Mitsubishi Electric WS-65615 Specifications

Ser vice
Manual
2005
MITSUBISHI ELECTRIC
PROJECTION TELEVISION
V27 CHASSIS
V27 MODELS
WS-55517
WS-55517
WS-65517
WS-73517
CAUTION:
Before servicing this chassis, it is important that the service person read the "SAFETY PRECAUTIONS" and
"PRODUCT SAFETY NOTICE" contained in this manual.
SPECIFICATIONS
• Power Input
: AC 120V, 60Hz
• Power Usage
: 275W
300W [WS-65517/ WS-73517]
• Frequency Range
: VHF 54 ~ 470MHz
UHF 470 ~ 806MHz
• Antenna Input
: VHF/UHF 75Ω unbalanced
1 - NTSC.ATSC/QAM
1 -NTSC for PIP
• CRT Size
: [7 inches] WS-55517/WS-65517
: [9 inches] WS-73517
• High Voltage
: 32.0kV (at 0A)
• Input Level
• Output Level
• Speakers (8 Ohms 10W)
: 2 - 6" full range
Model
WS-55517
WS-65517
WS-73517
Cabinet Weight & Demensions
Weight
Height
Width
221 lbs
50.7 in.
50.4in.
292 lbs
62 in.
59 in.
383 lbs
66.3 in.
65.9 in.
Depth
28 in.
28 in.
30 in.
• Weight and dimensions shown are approximate.
• Design specifications are subject to change without notice.
• Digital
Interface
: VIDEO IN JACK (RCA Type)
1.0Vp-p 75Ω unbalanced
: AUDIO IN JACK (RCA Type)
-4.7dBm 43kΩ unbalanced
: S-VIDEO IN JACK
(Y/C separate type)
Y:1.0 Vp-p C:0.286Vp-p(BURST)
75Ω unbalanced
: COMP / Y, Cr, Cb (RCA Type)
Y: 1.0 Vp-p Cr, Cb: 700mVp-p
: ATV / Y(G), Pr(R), Pb(B), H, V
Y: 1.0Vp-p with sync 75Ω (BNC)
Pr, Pb: 700mV 75Ω
H, V: 3.0Vp-p 75Ω
: VGA / R,G,B,V,H (15 pin D)
: VIDEO OUT JACK (RCA Type)
1.0Vp-p 75Ω unbalanced
: AUDIO OUT JACK (RCA Type)
-4.7dBm 4.7kΩ unbalanced
: IEEE-1394 I/O Jacks
: AC-3 Digtal Audio Output
: HDMI
: CableCARD
: System 5 IR
: USB Service Port
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road, Irvine, CA 92618-1904
Copyright © 2005 Mitsubishi Digital Electronics America, Inc.
All Rights Reserved
MODELS: WS-55517 / WS-65517 / WS-73517
CONTENTS
INTRODUCTION ................................................................................................................................ 5
PRODUCT SAFETY NOTICE ............................................................................................................. 5
SAFETY PRECAUTIONS ................................................................................................................... 6
DISASSEMBLY PROCEDURES ......................................................................................................... 7
Cabinet Disassembly (Front) .................................................................................................. 7
Cabinet Disassembly (Rear) .................................................................................................. 8
SERVICING THE LENTICULAR LENS AND FRESNEL SCREEN ....................................................... 9
Removal of the Lenticular Screen and Fresnel Lens ........................................................................ 9
Installation of the Lenticular Screen and Fresnel Lens ................................................................... 10
DIAMONDSHIELDTM Removal and Installation ............................................................................. 11
CABINET SEPARATION PROCEDURES
WS-65517 / WS-73517 Cabinet Separation .................................................................................. 12
SERVICING PCBs ............................................................................................................................ 12
Chassis Removal .......................................................................................................................... 12
PCB Locations .............................................................................................................................. 13
Major Parts Locations ................................................................................................................... 13
CRT REPLACEMENT ....................................................................................................................... 14
CRT Removal ................................................................................................................................ 14
CRT Installation ............................................................................................................................ 15
ELECTRICAL ADJUSTMENTS ........................................................................................................ 17
Equipment and Initial Setup .......................................................................................................... 17
Initial Setup ................................................................................................................................... 18
LED Indicator Diagnostics ............................................................................................................. 19
Remote Control Operational Mode ................................................................................................ 19
Circuit Adjustment Mode ............................................................................................................... 20
Service Mode Reset ...................................................................................................................... 21
Convergence Adjustment Mode ..................................................................................................... 21
Adjustment Items List ................................................................................................................... 23
Adjustment Procedures ................................................................................................................ 26
Test Point Locations ............................................................................................................ 26
Main / Sub Y Level & HV Regulation .................................................................................... 27
Main / Sub Color Level & CRT Cutoff .................................................................................... 28
White Balance (NTSC) & White Balance (HD) ..................................................................... 29
Black Level & Sub Contrast ................................................................................................. 30
Dynamic Focus Presets & Lens Focus ................................................................................ 31
Alignment Magnet / Electrostatic Focus & Character Position ............................................. 32
Geometry Presets ............................................................................................................... 33
Deflection Geometry Adjustments ........................................................................................ 34
Convergence Geometry Adjustments ................................................................................... 35
Centering & Static Convergence ........................................................................................... 36
Coarse Convergence Adjustments ........................................................................................ 37
Fine Convergence Adjustments ............................................................................................ 38
Page 3
MODELS: WS-55517 / WS-65517 / WS-73517
CHIP PARTS REPLACEMENT ......................................................................................................... 39
REPLACEMENT PARTS .................................................................................................................. 40
Parts Ordering .............................................................................................................................. 40
Critical and Warranty Parts Designation........................................................................................ 40
Parts Tolerance Codes .................................................................................................................. 40
Quick Reference List .................................................................................................................... 41
SERVICE PARTS LIST .................................................................................................................... 42
SCREEN ASSEMBLY PARTS LIST .................................................................................................. 55
CIRCUITRY BLOCK DIAGRAMS ..................................................................................................... 56
Part 2
V25/V27 Schematic Diagrams
CONTENTS
Page
SCHEMATIC DIAGRAMS
PWB Interconnect Diagram............................................................................................................. 1
PWB-MAIN (Power Supply / Horizontal Deflection / HV) ................................................................ 2
PWB-TERMINAL -1 (Input Switch) .................................................................................................. 3
PWB-TERMINAL 2 (PIC µPC / FIF /E2P) ....................................................................................... 4
PWBs-CRT / CONTROL / FRONT / PREAMP / SVM / DBF ........................................................... 5
HDMI .............................................................................................................................................. 6
PWB-SIGNAL-1 (MICRO) ............................................................................................................... 7
PWB-SIGNAL-2 (Convergence Generator) ....................................................................................... 8
PWB-SIGNAL-3 (VCJ / Vertical Deflection / Audio)) ........................................................................ 9
PWB-TUNER-1 (Tuners / Audio) .................................................................................................... 10
PWB-TUNER-2 (Demodulator) ...................................................................................................... 12
Page 4
MODELS:
WS-55517 / WS-65517 / WS-73517
INTRODUCTION
This service manual provides service instructions for projection TV models WS-55517, WS-65517 and WS-73517
using the V27 chassis. Service personnel should read this manual thoroughly before servicing these chassis.
This service manual includes:
1. Assembly and disassembly instructions for the front and rear cabinet components.
2. Servicing of the Lenticular Screen and Fresnel Lens.
3. Servicing printed circuit boards (PCBs).
4. CRT replacement procedure.
5. Electrical adjustments.
6. Chip parts replacement procedures.
7. Circuit path diagrams.
The parts list section of this service manual includes:
1. Cabinet and screen parts.
2. Electrical parts.
Schematic and block diagrams of the above listed models are included in this service manual for better understanding of the circuitry. PCB drawings are also included for easy location of parts and test points.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in television receivers have special safety related characteristics. These
characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be
obtained by using replacement components rated for higher voltage, wattage, etc.
Replacement parts which have special safety characteristics are identified in this service manual.
Electrical components having such features are identified by shading
on the schematic diagram and by bold
type in the parts list of this service manual. The replacement for any safety part should be identical in value
and characteristics.
Page 5
MODELS:
WS-55517 / WS-65517 / WS-73517
SAFETY PRECAUTIONS
NOTICE:
WARNING:
1.
2.
3.
Observe all cautions and safety related notes located inside the receiver cabinet and on the
receiver chassis.
Operation of this receiver outside the cabinet or with the cover removed presents a shock hazard
from the receiver's power supplies. Work on the receiver should not be attempted by anyone who is
not thoroughly familiar with the precautions necessary when working on high voltage equipment.
Do not install, remove or handle the picture tubes in any manner unless shatterproof goggles are
worn. People not so equipped should be kept away while the picture tube is being handled. Keep
the picture tube away from the body while handling.
When service is required, observe the original lead dress. Extra precaution should be taken to
assure correct lead dress in the high voltage area. Where a short-circuit has occurred, replace those
components that indicate evidence of overheating.
X-Radiation warning
The surface of the cathode ray tubes (CRTs) may generate X-Radiation, so take proper precautions when servicing. It is recommended that a lead apron be used for shielding while handling the CRT. Use this method if
possible.
When replacing the CRTs, use only the designated replacement part since it is a critical component with regard to
X-Radiation. High voltage must be set as prescribed under the section titled Electrical Adjustments.
Leakage current check
Before returning the receiver to the customer, it is recommended that leakage current be measured according to
the following methods.
1. Cold Check
With the alternating current (AC) plug removed from the AC source, place a jumper across the two AC plug
prongs. Connect one lead of an ohm meter to the AC plug and touch the other lead to each exposed metal
part (i.e. antennas, handle bracket, metal cabinet, screw heads, metal overlay, control shafts, etc.), particularly any exposed metal part that has a return path to the chassis. The resistance of the exposed metal parts
having a return path to the chassis should be a minimum of 1Meg Ohm. Any resistance below this value
indicates an abnormal condition and requires corrective action.
2. Hot Check ...Use the circuit shown below to perform the hot check test.
1. Keep switch S1 open and connect the receiver to the measuring circuit. Immediately after
connection, and with the switching devices of the receiver in their operating positions, measure
the leakage current for both positions of switch S2.
2. Close switch S1, energizing the receiver. Immediately after closing switch S1, and with the
switching devices of the receiver in their operating positions, measure the leakage current for both
positions of switch S2. Repeat the current measurements of items 1 and 2 after the receiver has
reached thermal stabilization. The leakage current must not exceed 0.5 milliampere (mA).
Page 6
MODELS:
WS-55517 / WS-65517 / WS-73517
CABINET DISASSEMBLY (FRONT VIEW)
*Refer to the Parts List for Part Numbers
Front Cabinet Disassembly
1.
2.
3.
4.
5.
6.
Remove the Speaker Grille by pulling forward.
Remove the Board Front by removing screws (a).
Remove 4 screws (b) holding the Screen Assembly (all models).
Remove screws (c) from the Screen Assembly (WS-65517 & WS-73517 only)
Unplug the CC, ZF and GR connectors from the Control Panel.
Lift the Screen Assembly up and away from the cabinet.
Page 7
MODELS:
WS-55517 / WS-65517 / WS-73517
CABINET DISASSEMBLY (REAR VIEW)
*Refer to the Parts List for Part Numbers
Rear Cabinet Disassembly
1.
2.
3.
4.
5.
6.
Remove the Back Board by removing screws (a), and screws (b).
Remove screws (c) to remove the Board Slide.
Remove screws (d) to remove the Board Shelves.
Remove screw (e) holding the chassis.
Remove 4 screws (f) securing the Light Box Assembly.
Be certain that all cables and connectors between the Light Box Assembly and external items are
disconnected (e.g. speaker plugs, etc.), including the USB and 1394 connectors.
7. Slide the Light Box Assembly from the cabinet.
Page 8
MODELS:
WS-55517 / WS-65517 / WS-73517
SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS
WS-55517 / WS-65517 / WS-73517
CAUTION:
Wear gloves when handling the Lenticular Screen and Fresnel Lens.
This prevents cuts and finger prints. Do not place Fresnel Lens in the sun.
This may cause fire and heat related injuries.
1b. Lenticular Screen and Fresnel Lens Removal
1. Remove the screen assembly as shown in the Cabinet Disassembly procedure.
2. Remove the Screen Frame top section by removing 4 screws (a).
3. Carefully grasp the Lenticular Screen and Fresnel Lens combination, and pull upward and out of the Screen
Frame Assembly.
Note: When separating the Lenticular Screen from the Fresnel Lens, use caution
while prying the Screen and Lens apart. Use a slot type screw driver, and
remove the pressure sensitive double sided tape.
(Rear View)
Page 9
MODELS:
WS-55517 / WS-65517 / WS-73517
SERVICING THE LENTICULAR SCREEN AND FRESNEL LENS
2. Lenticular Screen and Fresnel Lens Installation.
Note: Store the Lenticular Screen and Fresnel Lens in a cool dry place. High humidity may
deform the Lenticular Screen and Fresnel Lens.
1. Apply double coated tape (Part # LENS-TAPE) along the top front edge of the Fresnel Lens
as shown below. Refer to the Table below for proper tape length.
2. Place the Fresnel Lens on top of the Lenticular Screen and apply pressure at the top edge
to bond them together as shown below.
Model
WS-55517
WS-65517
WS-73517
Screen
Size
55"
65"
73"
Page 10
Tape
Length
47.8"
56.5"
63.5"
MODELS:
WS-55517 / WS-65517 / WS-73517
SERVICING THE DIAMONDSHIELD™
1. DiamondShield™ Removal Procedure
The appropriate disassembly procedure given below.
Note: Wear gloves when handling the DiamondShield™ to prevent finger prints.
1. Gently insert a small plastic card (such as a credit card or a
plastic putty knife) between the Diamond ShieldTM and one end of
the clip to pry the clip loose.
2. From the edge of the trim, pull the brackets outward to open like
a hinge.
3. Carefully insert the small plastic card (or plastic putty knife) into
the gap at the side/center point of the Shield and pull the Shield
slightly away from the unit. Place your hands at the points
shown and gently bow the Shield toward you and remove from the
unit.
4.
Close the two trim brackets at the sides.
2. DiamondShield™ Installation Procedure
To install the DiamondShieldTM, reverse the above Removal Procedure.
*(See the Parts List for DiamondShield™ part numbers)
Page 11
MODELS:
WS-55517 / WS-65517 / WS-73517
CABINET SEPARATION PROCEDURE
WS-65517 / WS-73517
Cabinet Separation Procedure
1. Pull the Speaker Grill from the cabinet.
2. Unplug the CC, ZF and GR connectors.
3. Remove 4 plastic covers and screws (a)
from each side of the cabinet.
4. Carefully lift the cabinet top and place it on
the floor.
5. Place the cabinet bottom in the desired
location.
6. Reverse the procedure and mount the
cabinet top on the cabinet bottom.
Main Chassis Removal
Chassis Removal
1.
2.
2.
3.
4.
5.
Undo the cable wire ties to the Front Panel, Speakers, CRTs, etc.
Unplug the 1394 cables from the DM module.
Remove screw (a) securing the Main Chassis.
Release the Chassis Locks on each side of the chassis.
Slide the Chassis out the rear of the unit.
Tilt upward to access the bottom of the main chassis.
Page 12
MODELS:
WS-55517 / WS-65517 / WS-73517
PCB Locations
Main Components Location (Top View)
(DM Fan & Bracket Removed)
Page 13
MODELS:
WS-55517 / WS-65517 / WS-73517
CRT REPLACEMENT
1. Removal of the CRT
Caution!
High voltage should be completely discharged prior to CRT removal.
Since The CRTs receive high voltage from the HV Block, discharge
by shorting the open end of the respective high voltage cable to
chassis ground.
Note: Refer to the Cabinet Disassembly Procedures when performing steps 1 through 4.
1.
2.
3.
4.
5.
6.
Remove the Speaker Grille, Front Board, and Screen Assy.
Remove the Back Board.
Remove the Anode Lead Wire from the CR Block.
Remove the PCB-CRT.
Remove 4 hex-screws "a" retaining the Optical Unit. [Figure 5-1]
Remove 4 screws "b" retaining the Lens.
Note: DO NOT loosen the RED screws. Doing so will break the seal between the
C-Element and the # 6 Lens, causing leakage of the CRT Coolant.
7. Remove 4 screws "c" retaining the CRT. [Figure 5-2]
8. Remove the Deflection Yoke from the neck of the CRT. [Figure 5-7]
Figure 5-1
Figure 5-2
Note: The 4 spring-loaded screws shown
in Fig 5-2 and labeled as "DO NOT
REMOVE", should not be loosened
under any circumstance. Doing so
will break the seal between the
CRT and the CRT-Spacer, causing
leakage of the CRT Coolant.
Page 14
MODELS:
WS-55517 / WS-65517 / WS-73517
2. Installation of the CRT
Note: The replacement CRT is supplied as an assembly comprised of the CRT and the
Inner Lens with the space between them filled with ethylene glycol. Care should
be taken during handling and installation to prevent shock from disrupting the seal
or alignment between the CRT and Inner Lens. [Figure 5-3]
Figure 5-3
Note: The CRT fixing screws should not be loosened nor should they be removed. [Figure 5-4]
Figure 5-4
1. Carefully position the replacement CRT and fasten in place using 4 screws "d". [Figure 5-6]
Figure 5-6
Figure 5-5
Page 15
MODELS:
WS-55517 / WS-65517 / WS-73517
2. Install the Deflection Yoke on the CRT neck. [Figure 5-7]
3. Install the Lens that was removed in step 6 of Removal Of The CRT. [ Figures 5-1 and 5-2 ]
a) Position the Lens so that the Label faces the direction shown in Figure 5-8.
b) Install the mounting screws. [Figure 5-1]
4. Connect the PCB-CRT.
5. Insert the Optical Unit into the Light Box Assembly.
6. Insert the Anode Lead Wire into the Flyback Transformer.
7. Re-clamp the Lead Wire in its original position.
Figure 5-7
Figure 5-8
Adjustment procedures after replacing the CRT(s)
• CRT Cut Off / White Balance Adjustment
• Static Convergence Adjustment
• Dynamic Convergence Adjustment
Page 16
MODELS:
WS-55517 / WS-65517 / WS-73517
ELECTRICAL ADJUSTMENTS
Note: Perform only the adjustments required.
Do not attempt an alignment if proper equipment is not available.
Test Equipment
•
•
•
•
•
•
•
Oscilloscope (Unless otherwise specified, use 10:1 probes)
Signal Generator (both SD and HD capable)
Frequency Counter
Direct Current Voltmeter
Direct Current Power Supply
Multiplex Audio Signal Generator
Direct Current Ampere Meter
Test Signal
A. Monoscope Signal
Note: If you do not have
a monoscope signal source,
connect the unit to a VCR
and play a Monoscope
*alignment tape.
(* Part Number: 859C568060)
B. Color Bar Signal
Use the color bar signal shown
below, unless otherwise specified
in this manual.
Monoscope Signal
100%
75%
40%
40%
1H
Split-Field Color Bars (100% window)
Page 17
MODELS:
WS-55517 / WS-65517 / WS-73517
Initial Setup
A. Option Menu Setup
Follow the steps below for the initial set-up:
1. Select the "MENU" display by pressing the "MENU" button once.
2. Press the number buttons "2", "4", "7", "0" in sequence to select
the "OPTION MENU" display.
3. Press the "ADJUST" button to select "INITIAL."
4. Press "ENTER."
NOTE: At this time channel 3 is automatically selected.
B.
Default Settings
(MENU-2-4-7-0)
OPTION MENU
Initial
Power Restore
Direct Key Mode
:Off
:Off
MAIN MENU DEFAULT SETTINGS
SETUP
CAPTIONS
Edit Setup
Analog Captions
With Mute
Background
Gray
Review
Antenna 1
Enabled
Digital Captions
With Mute
Antenna B
Enabled
Digital Settings
Input DTV
Enabled
Appearance
Default
Input 1
Enabled
Digital Channel Guide
Off
Input 2
Enabled
V-CHIP LOCK
Input 3
Enabled
Component 1
Enabled
V-CHIP
Off
Component 2
Enabled
TV Rating
TV-PG
Antenna DTV
Enabled
FV-Fantasy Violence
Enabled
VGA
Enabled
D-Sexual Dialog
Enabled
HDMI
Enabled
L-Adult Language
Enabled
Icon Position
S-Sexual Situation
Enabled
Ant-A, Ant-B, Ant-DTV, ComFlash
V-Violence
Enabled
Input-1, Input-2, Input-3, Comp-1,
Program not Rated
Enabled
Comp-2, HDMI.
Movie Rating
PG
Transport Menu
On
V-Chip Time
English
Start Time
12:00 AM
Language
Stop Time
12:00 AM
ANTENNA
Lock By Time
Antenna
ANT A
Memorize Channels
Air
Lock by Time
Off
Channel
Ch-3
Lock Time
NA
Memory
Deleted
Unlock Time
NA
TIME
Front Button Lock
Off
Clock Setting
Manual
AUDIO/VIDEO SETTINGS
Time
12:00 AM A/V Memory Reset
Ant-A
Day
Monday Audio
Volume
30%
Bass
50%
Treble
50%
Balance
50%
Surround
Off
Listen to
Stereo
Level Sound
Off
TV Speakers
On
Audio 2 Out
Main
Video
Contrast
100%
Brightness
50%
Sharpness
50%
Color
50%
Tint
50%
Color Temp.
High
Video Noise
Standard
Image Type
Video
VSM Sharpness
On
Video Mute
On
Black Enhancement
On
Advanced
Color Balance
Manual
PerfectColor™
A/V Memory for Ant-A
All Centered
PIP/POP
Source
Ant A Ch 3
PIP Position
Lower Right
POP Position
Right Half
PIP/POP Format
Dble. Window
Stretched
Format
A/V RESET DEFAULT SETTINGS (By Input)
INPUTS Component 1394 when
A/V Memory
Ant 1/2
HDMI
1/2/3
1/2/DTV
connected
Contrast
Max.
Max.
Max.
Max.
Max.
Brightness
Center
Center
Center
Center
Center
Sharpness
Center
Center
Center
Center
Center
Color
Center
Center
Center
Center
Center
Tint
Center
Center
Center
Center
Center
Color Temp.
High
High
High
High
High
Video Noise
Standard Standard
Standard
N/A
Standard
TV Film Mode (Auto)
On
On
On
N/A
On
TV DefinEdge VSM
On
On
On
On
On
Bass
Center
Center
Center
Center
Center
Treble
Center
Center
Center
Center
Center
Balance
Center
Center
Center
Center
Center
Surround
OFF
OFF
OFF
OFF
OFF
Listen To
Stereo
N/A
N/A
N/A
N/A
Level Sound
OFF
OFF
OFF
OFF
OFF
Page 18
MODELS:
WS-55517 / WS-65517 / WS-73517
C. A/V Memory
Each of the external inputs has its’ own Audio/Video Memory. A change in an A/V setting at a specific input is
stored in memory for that specific input.
A/V Reset
1. The front panel AV Reset button initializes all A/V Memories.
2. The AV Reset in the user’s menu initializes only the selected input’s A/V Memory.
LED Indicator Diagnostics
The “Power ON LED” provides an indication of the sets operation, and the possible cause of a malfunction.
1. Initial Control Circuitry Check
Immediately after the TV is connected to an AC power source:
LED Indica tions
Off
Fast B link for 70 sec.
Fast B link (Doesn't stop)
Slow Blink
Conditions
A fter AC is applied
A fter AC is applied
A fter AC is applied
Set is Off
Proba ble Ca use
No Standby P ower or TV µP C not running
Normal - DM µPC is booting up.
TV µPC is running, but DM failed to boot up
Normal - Timer is set for Auto Trun On
2. Error Code Operational Check
Note: The TV must be in “Shut Down” and not have been switched Off, to perform the Error Code Operational Check. When the TV is switched Off, the code automatically resets to “12” No Error.
Pressing the front panel “INPUT” and “MENU” buttons at the same time, and holding for 5 seconds,
activates the Error Code Mode. The LED flashes denoting a two digit Error Code, or indicating no problem
has occurred since the last Initialization.
Note: The front panel buttons must used, NOT those on the Remote Control.
•
•
•
•
The number of flashes indicates the value of the MSD (tens digit) of the Error Code.
The flashing then pauses for approximately 1/2 second.
The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.
The Error Code is repeated a total of 5 times.
Example: If the Error Code is “23”, the LED will flash two times, pause, and then flash three
times.
3. Error Codes
The Error Code designations indicating malfunction, or no malfunction, are listed below:
Error Code
12
21
22
23
Probable Cause
No error detected
X-Ray Protect
Short Protect
Loss of Deflection
Remote Control Operational Modes
There are two Remote Hand Unit Operational Modes, “Standard” and “NetCommandTM”. The Remote is initially
in the “Standard” mode. The “NetCommandTM” mode is used when controlling Home Theater devices using
NetCommandTM. To change the Remote Operational Mode:
•
•
•
•
Set the Remote to the TV Layer
Point the Remote away from the TV.
To change to “NetcommandTM” ... Hold the “Power” button and press “9-3-5” in sequence.
To change to “Standard” ... Hold the “Power” button and press “0-0-0” in sequence.
Page 19
MODELS:
WS-55517 / WS-65517 / WS-73517
Circuit Adjustment Mode
Most of the adjustments can only be performed using the remote hand unit. Many of the adjustments must be
performed in both the 480i and 1080i modes. Video/Color adjustments must be performed in the 480i and
1080i modes, and data must be preset in the 480P (DVD) and VGA modes.
Note: Set the Remote Operational Mode to “NetCommandTM”. (Hold the “Power” button and press
“9-3-5” in sequence.) This slows the remote’s response and makes adjustments easier. When
adjustments are complete, set the Remote to its’ original Operational Mode.
(Hold the “Power” button and press “0-0-0” in sequence)
A. Activating the Circuit Adjustment Mode
The current signal source determines if the
activated Adjustment Mode is 480i or 1080i.
1. Select the signal source (480i or 1080i).
2. Press the "MENU" button on a remote hand unit.
3. Press the number buttons "2, "4", "5", "7" in sequence. The screen will
change to the Adjustment Mode.
Note: Repeat steps 1 and 2 if the circuit
adjustment mode does not appear
on screen.
CHASSIS
FUNCTION
ADJ ITEM
ISF
MMTX
15 YD RM 5
ABBREV.
480i
SIGNAL
DATA
B. Selection of adjustment Functions and Adjustment Items
To select an adjustment item in the circuit adjustment mode, first select the adjustment function that includes
the specific adjustment item to be selected. Then select the adjustment item. Refer to the following pages for
the listing of adjustment functions and adjustment items.
1. Press the "AUDIO" button on a remote hand unit to select an adjustment function. Each time the button
is pressed, the Function changes in the following sequence:
CRT_JUNGL
CRT_VC
SMTX
AD9883A
MMTX
Adjustment Functions
2. Press the “VIDEO” button to select a specific Adjustment Item. The Item number increases each time the
“VIDEO” button is pressed.
C. Changing Data
After selecting an adjustment Item, use the “ADJUST UP/DOWN” buttons to change data.
• Press “ADJUST DOWN” to decrease the data value.
• Press “ADJUST UP” to increase the data value.
D. Saving Adjustment Data
Press “ENTER” to save adjustment data in memory. The character display turns red for approximately one
second in this step.
Note: If the circuit adjustment mode is terminated without pressing “ENTER”, changes in adjustment data
are not saved.
Page 20
MODELS:
WS-55517 / WS-65517 / WS-73517
E. Terminating the Circuit Adjustment Mode
Press the “MENU” button on the remote hand unit twice to terminate the adjustment mode.
Note: The circuit adjustment mode can also be terminated by turning power OFF.
F. Toggle Between Reception Modes
Pressing “3” when in the Adjustment Mode CRT-VC Function toggles between 480i, 480p, 1080i and VGA.
However data changes are not automatically saved. Press “ENTER” to save data before pressing “3”.
G. Service Mode Reset
To reset items in the Service Mode to their factory values:
1. Press MENU-2-4-5-7 to enter the Service Mode.
2. Press the “0”.
3. Select “Restore Backup”
4. Press “”ENTER”
"MENU-2-4-5-7-0"
Restore Backkup
UPLOAD TERMINAL BOARD DATA
On Screen Display Position Adjustment Mode
Activation
1.
2.
Select 480i or 1080i source.
Press MENU-2-4-8-8
Convergence Adjustment Mode
The Convergence mode is used to perform raster geometry
correction, and convergence adjustments. These adjustments must be made in both the SD (NTSC) and HD modes.
Note: Before activating the Convergence mode, turn
“Video Mute” Off. The internal crosshatch pattern
will not be displayed with “Video Mute” On, only a blue
background is displayed.
convM
COARSE GREEN
0
HSTA
ITEM
NO.
00
ABREV
DATA
A. Convergence Mode Activation
1.
2.
Press MENU-2-4-5-9
When the Convergence Mode is activated, this display appears on a Green Crosshatch.
B. Selecting the HD or SD Mode
1.
Select the Signal Source before entering the
Convergence Mode, either an NTSC or HD source.
2.
Enter the Convergence Mode
• If the signal source is NTSC, the SD mode is activated.
• If the signal source is HD, the HD mode is activated.
3.
Activating the HD mode when no HD signal is available
• Press the “DEVICE” button.
• Use the “UP-DOWN-RIGHT-LEFT” direction buttons to select the ANT-DTV, then press “ENTER”.
• Press “MENU-2-4-5-9-5” in sequence to activate the Coarse Green HD Convergence mode.
C. Convergence Mode Functions
In the Convergence Mode there are three main Functions (Categories).
• Pressing “6” activates CONV MISC
• Pressing “5” activates COARSE CONV
• Pressing “4” activates FINE CONV
Page 21
MODELS:
WS-55517 / WS-65517 / WS-73517
D. CONV MISC (Press 6)
This mode is used to preset data values controlling the Convergence Generator, and to perform the HV
Regulation adjustment.
1. Use the VIDEO button to select an item.
2. Use the ADJUST buttons to change data.
NOTE: When Item “1 HVOL” is selected the screen goes black except for the data display. This occurs
since a black screen is required when making the HV Regulation adjustment.
E. COARSE CONV (Press 5)
There are four Sub Functions in the Coarse mode, COARSE GREEN, COARSE RED, COARSE BLUE and
DF.
• COARSE GREEN .... used to make Coarse Raster Geometry Adjustments.
• COARSE RED ... used to make Coarse Red Convergence Adjustments.
• COARSE BLUE ... used to make Coarse Blue Convergence Adjustments.
• DF ... used to preset data values controlling the Dynamic Beam Focus circuit drive signal.
1. Use AUDIO button to select a Sub Function
2. Use the VIDEO button to select an Adjustment Item.
3. Use the ADJUST buttons to change data.
F. FINE CONV (Press 4)
Sub Functions
This mode is used to perform Fine Raster Correction, and Fine Red and Blue Convergence Adjustments.
There are three Sub Adjustment Functions, selected with the AUDIO button:
• FINE GREEN .... a Green Crosshatch is displayed, to make Fine Raster Corrections.
• FINE RED .... a White Crosshatch is displayed, to make Fine Red Convergence Adjustments.
• FINE BLUE .... a White Crosshatch is displayed, to make Fine Blue Convergence Adjustments.
Cursor
In the Fine mode a Cursor is added to the Crosshatch. The ENTER button toggles the Cursor between two
modes:
• MOVE (blinking Cursor) .... use the ADJUST buttons to select any of 64 points on the Crosshatch.
• ADJUST (Non blinking Cursor) .... the ADJUST buttons adjust the active color at the current Cursor
position, horizontally or vertically.
Display
The on-screen display changes in the Fine mode, as shown at the right.
The display shows the vertical and horizontal data for the current Cursor
Position, and the horizontal and vertical coordinates for that position.
G. Saving Data and Exiting the Convergence Mode
Press MENU twice to exit the Convergence mode, data is automatically saved.
Page 22
V27
CONV FINE
V13
VERTICAL
DATA
GREEN
H-4
SD
HORIZ.
DATA
MODELS:
WS-55517 / WS-65517 / WS-73517
E2PROM Replacement
Data accessed in the Convergence Adjustment Mode is stored in IC8D01on the PCB-SIGNAL. Replacement
PCB’s are supplied pre-aligned so that only fine adjustments should be necessary after replacement. All other
service data is stored on the PCB-E2P located on the DM assembly. When replacing the DM assembly,
retaining the original PCB-E2P will eliminate the need for any realignment. The following tables are provided as
a guide in case of total data loss.
List of Adjustment Items.
VC Function (Video Color)
MENU-2-4-5-7
Data
Initial Data
Notes
Range 480i 480p 1080i
0~63
20
20
20
Black Level
0~63
31
42
42
Sub Contrast
0~15
7
7
7
Preset
0~15
31
31
31
White Balance
0~15
37
41
41
"
0~63
31
31
31
White Balance
0~63
31
31
31
"
0~63
25
31
31
"
0~63
31
31
31
"
0~63
31
31
31
"
0~63
37
41
41
"
0~63
31
31
20
"
0~63
31
31
25
"
0~63
25
31
35
"
0~63
31
31
20
"
0~3
2
2
2
"
0~1
0
0
0
Preset
0~63 28/*32 33
36
User
0~63
34
35
32
User
0~63 26/*29 30
29
User
0~63
31
31
31
Preset
0~63
31
31
31
"
0~3
1
1
2
"
0~3
0
0
0
"
Function Display
Adjustment
NO.
Abbrev.
Description
1
SBRT
Sub Brightness Adjust
2
SCT
Picture Gain Adjust
3
SCON
Sub Contrast Adjust
4
RDRH
R-Drive (high)
5
GDRH
G-Drive (high)
6
BDRH
B-Drive (high)
7
CTRH
R-Cutoff (high)
8
CTGH
G-Cutoff (high)
9
CTBH
B-Cutoff (high)
10
RDRL
R-Drive (low)
11
GDRL
G-Drive (low)
12
BDRL
B-Drive (low)
13
CTRL
R-Cutoff (low)
14
CTGL
G-Cutoff (low)
15
CTBL
B-Cutoff (low)
16
GMMA
RGB Gamma correction
17
GAML
Gamma Differ. Sw.
18
BRT
Brightness Control
19
COL
Color Control
20
TNT
Hue Control
22
CBOF
Cb sub signal DC cancel
23
CR0F
Cr sub signal DC cancel
38
DCTR
Y DC trans. Ration
56
ASBL
S-ABL gain setting
* Component Input
CRT-JNGL Function (Jungle)
Display
No.
1
2
7
8
9
13
18
Item
HWID
HKEY
VHGT
VLIN
VSCN
H-POS
V-POS
Adjustment
Description
Data
Range
Horizontal Width
Horizontal Keystone
Vertical Height
Vertical Linearity
Vertical S-Correction
Horizontal Position
Vertical Position
0~63
0~63
0~63
0~15
0~15
0~63
0~63
Page 23
MENU-2-4-5-7
WS-55517
WS-65517
WS-73517
HD
25
41
28
6
3
38
31
HD
21
25
33
6
3
38
31
HD
28
25
33
6
3
38
31
SD
25
37
31
6
3
23
31
SD
21
24
38
6
3
23
31
SD
28
24
41
6
3
23
31
MODELS:
WS-55517 / WS-65517 / WS-73517
MAIN MATRIX
Item
Abbrev.
Description
Number
Name
4
COLM Color Gain Control
15
YDRM Y Drive Gain Control
(MENU-2-4-5-7)
Initial
Range
Data
0~63
17
0~63
5
SUB MATRIX
Item
Abbrev.
Description
Number
Name
4
COLS Color Gain Control
15
YDRS Y Drive Gain Control
(MENU-2-4-5-7)
Initial
Range
Data
0~63
17
0~63
5
AD9883A
Item
Number
12
14
Abbrev.
Name
ROFF
BOFF
Data
(Hex)
3A
3C
Description
Red Offset
Blue Offset
OSD Horiz. Centering
(MENU-2-4-8-8))
Abbrev.
Description
DATA
Name
HR
Display Horiz. centering (NTSC)
120
DYNAMIC FOCUS
Item
Abbrev.
Number
Name
1
DFH
2
DFV
(MENU-2-4-5-9-5)
Description
Dynamic Horiz. Focus
Dynamic Vert. Focus
CONV MISC.
Item
Abbrev.
Number
Name
1
HVOL
Data
-450
200
(MENU-2-4-5-9-6)
SD DATA HD DATA
228
Page 24
216
Notes
HV adj.
MODELS:
WS-55517 / WS-65517 / WS-73517
CONV GREEN Items
(MENU-2-4-5-9-5)
No. Abbrev.
Description
Name
1
HSTA*
Horizontal Position
2
VSTA*
Vertical Position
3
SKEW
Skew (Y axis rotation)
4
TILT
Tilt (X axis rotation)
5
HWID
Horisontal Width
6
HLIN
Horizontal Linearity
7
SPCC
Side Pin Cushion Correction
8
HKEY
Horizontal Keystone
9
TBPC
Top/Bottom PC Correction
10
VKEY
Vertical Keystone
11
VWID
Vertical Height
12
VLIN
Vertical Linearity.
*HSTA and VSTA must not exceed ±200
WS-55517 WS-65517 WS-73517
SD
HD
SD
HD
SD HD
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
20
20
20
20
20
20
12
12
12
12
12
12
0
0
0
0
0
0
0
0
0
0
0
0
-195 -180 -200 -170 -210 -180
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
CONV RED Items
(MENU-2-4-5-9-5)
No. Abbrev.
Description
Name
1
HSTA
Horizontal Position
2
VSTA
Vertical Position
3
SKEW
Skew (Y axis rotation)
4
TILT
Tilt (X axix rotation)
5
HLIN
Horixontal Linearity
6
HWID
Horizontal Width
7
VKEY
Vertical Keystone Correction
8
VWID
Vertical Height
9
VLIN
Vertical Linearity
10
TPPC
Top/Bottom PC Correction
11
SDBW
Horizontal Side Bow
*HSTA and VSTA must not exceed ±200
WS-55517 WS-65517 WS-73517
SD
HD
SD
HD
SD HD
50
50
50
50
10
100
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-210 -150 -180 -160 -230 -210
10
10
0
0
0
0
-100 -100 -100 -90 -140 -110
0
0
0
0
0
0
0
0
0
0
0
0
20
20
20
20
20
20
30
30
30
30
30
30
CONV BLUE Items
(MENU-2-4-5-9-5)
No. Abbrev.
Description
Name
1
HSTA
Horizontal Position
2
VSTA
Vertical Position
3
SKEW
Skew (Y axis rotation)
4
TILT
Tilt (X axix rotation)
5
HLIN
Horixontal Linearity
6
HWID
Horizontal Width
7
VKEY
Vertical Keystone Correction
8
VWID
Vertical Height
9
VLIN
Vertical Linearity
10
TPPC
Top/Bottom PC Correction
11
HSBW
Horizontal Side Bow
*HSTA and VSTA must not exceed ±200
Page 25
WS-55517
SD
HD
-50 -50
0
0
0
0
0
0
180 180
0
0
100 100
0
0
0
0
-20 -20
-30 -30
WS-65517
SD
HD
-50 -50
0
0
0
0
0
0
180 160
0
0
100
70
0
0
0
0
-20 -20
-30 -30
WS-73517
SD HD
-100 -100
0
0
0
0
0
0
230 200
0
0
70
90
0
0
0
0
-20 -20
-30 -30
MODELS: WS-55517 / WS-65517 / WS-73517
Adjustment Test Point Location
Test Points
DT pin 3 - HV Adjust
DT pin 6 - Ground
DT pin 7 - 12 Volts
DT pin 8 - ACL
JA pin 25 - Main Picture (Y)
JA pin 29 - Main Picture (Cr)
JA pin 40 - Sub Picture (Y)
JA pin 44 - Sub Pictur (Cr)
TP6(R, G or B) - CRT Cathode
Page 26
MODELS: WS-55517 / WS-65517 / WS-73517
[HV Circuit]
1. HV Regulation
Measuring
Instrument
DC Voltmeter
Test Point
DT connector pins 3 & 6
Ext. Trigger
Measuring
Range
------
Input Signal
------Video Signal
Monoscope
Input Terminal
Video Input
Purpose:
To set the CRT Anode voltage.
Symptom:
Dark Picture
Note: This adjustment must be rechecked following Adjustment 9 CRT Cutoff.
1. Supply a video monoscope signal.
2. Sent Contrast to maximum, and Brightness to mid position.
3. Connect a DC volt meter between pins 3 and 6 of the DT connector.
(Positive lead to pin 3)
4. Activate the Conv-Misc Mode.
5. Select Item “1 HVOL” (screen goes black).
6. Adjust Item “1 HVOL” for 15.4V ±0.2V on the meter.
7. Save data and exit the Conv-Misc mode.
8. Confirm that the voltage does not change more than 0.15V.
Note: This adjustment must be performed if E2RESET or Convergence E2RESET
are activated.
CONVERGENCE MODE
Activate … …..MEN U-2-4-5-9
Mis c. ……… ……… .… …"6"
C oars e… ……… ……..…."5"
Fine ……… ………… …..."4"
C olor (R ,G or B)…… AUD IO
Item No…… …….…..VIDEO
Adjus t/Move…… ….ADJUST
C urs or Toggle….…..EN TER
Save & Exit…..MEN U (tw ice)
[Video Circuit]
Purpose
2. Main/Sub Y Level
Symptom:
Measuring
Instrument
Oscilloscope
Test Point
JA connector pins 26 &35
Ext. Trigger
------
Measuring
Range
Input Signal
Input Terminal
-----Color Bars
Video Input
To set picture luminance
Excess or insufficient brightness.
1.
2.
3.
4.
5.
6.
Supply a color bar signal to a Video Input (not an RF input).
Select the color bar signal for both the main and sub pictures.
Connect the oscilloscope to connector JA pin 25.
Activate the Adjustment Mode
Select Item “15 YDMR” in the MAIN MTRX function.
Adjust the data for 0.66 Vp-p min.- 0.71 Vp-p max. at JA pin 25.
(If it cannot be adjusted within this range, set to the lower value)
7. Move the oscilloscope to JA pin 40.
8. Select Item “15 YDRS” in the SUB MTRX function.
9. Adjust the data to equal the MAIN-Y Gain (+0.0V -0.05V).
CIRCUIT ADJUST MODE
Activate …….. MEN U-2-4-5-7
Function … ...…… …..AUD IO
Item No. …… ….…….VIDEO
Adjus t Data ….…….AD JU ST
Save Data …. ……… ENTER
Exit ……… …..MEN U (twice)
Page 27
MODELS: WS-55517 / WS-65517 / WS-73517
To match the sub picture color to that of the main picture.
[Video Circuit]
Purpose:
3. Main/Sub Color Level
Symptom: Main and sub pictures colors differ.
Measuring
Instrument
Oscilloscope
Test Point
JA pin 29 & JA pin 37
JB pin 5
Ext. Trigger
------
Measuring
Range
------
Input Signal
Color Bars
Input Terminal
Video
1.
2.
3.
4.
5.
6.
Supply an NTSC signal to an External Video Input.
Select the NTSC signal as the source for both the main and sub pictures.
Connect an oscilloscope to connector JA pin 29 (Main Pr).
Activate the Adjustment mode.
Select Item “04 COLM” in the Main Matrix Function.
Adjust data so the PR signal is 0.66 Vp-p min. - 0.71 Vp-p max.
(If it cannot be adjusted within this range, set to the lower value)
7. Connect an oscilloscope to connector JA pin 44 (Sub Pr).
8. Select item “04 COLS” in the Sub Matrix Function.
9. Adjust so Sub PR = Main PR (+0.0V ~ -0.05V).
CIRCUIT ADJUST MODE
Activate …….. MEN U-2-4-5-7
Function … ...…… …..AUD IO
Item No. …… ….…….VIDEO
Adjus t Data ….…….AD JU ST
Save Data …. ……… ENTER
Exit ……… …..MEN U (twice)
[CRT Circuit]
Purpose
To set the cutoff point for all three CRTs.
4. CRT Cutoff
Symptom:
Monochrome has a color tint, or incorrect brightness.
Measuring
Instrument
Oscilloscope
Test Point
TP6R, TP6G, TP6B
Ext. Trigger
------
Measuring
Range
Input Signal
Input Terminal
50V/Div. 2msec/Div.
None
Video Input
VC Function
Ite m
Abbr.
1
SBRT
2
SCT
3
SCON
4
RDRH
5
GDR
6
BDRH
7
CTRH
8
CTGH
9
CTBH
Se tting
20
31
7
31
37
31
31
25
31
Note: Use the Expand mode (full screen)
1. Select an External Input with no signal.
2. Enter the Adjustment Mode, VC Function.
3. Press “1”, automatically blanks the screen and sets COL to 0.
Note: If the screen goes blue, turn off Video Mute.
4. Set the data to the values given in the table below.
5. Connect the oscilloscope to TP6R.
6. Adjust the Red Screen VR so the black level is 175V, as shown below, or
179V ±1VDC using an DC Voltmeter.
7. Repeat Steps 4 and 5 to set the Blue and Green Screen VRs, using
TP6G and TP6B.
Note: White Balance must be performed
after this adjustment.
CIRCUIT ADJUST MODE
Activate …….. MEN U-2-4-5-7
Function … ...…… …..AUD IO
Item No. …… ….…….VIDEO
Adjus t Data ….…….AD JU ST
Save Data …. ……… ENTER
Exit ……… …..MEN U (twice)
Page 28
MODELS: WS-55517 / WS-65517 / WS-73517
Purpose:
[CRT Circuit]
5. White Balance (NTSC)
Measuring
Instrument
Test Point
Ext. Trigger
Measuring
Range
Input Signal
Input Terminal
Symptom:
Note: Use the “FORMAT” button to activate the Expand mode (full screen).
------
1. Supply a full White Raster Signal
2. Activate the Service Mode, VC function.
3. Adjust Items “4 RDRH” and “6 BDRH” for optimum white at the center of
the screen.
4. Reduce the input luminance level to 25%.
5. Adjust Items “7 CTRH” and “9 CTBH” for optimum white.
6. Insert a Milliammeter in series with each CRT Cathode. The maximum
allowable current for each CRT is given in the table below.
7. Set the white raster to 100% and adjust Items “10 RDRL” and “12 BDRL” for
optimum white at the center of the screen.
8. Reduce the luminance level to 25%.
9. Adjust Item “13 CTRL” and “15 CTBL” for optimum white.
10. Set the data for Item “19 COL” back to 31.
----------NTSC White Raster
RF or Video
Maximum CRT Current
WS-55517
CRT
WS-65517
RED
580ua
GREEN
580ua
BLUE
580ua
Purpose
[CRT Circuit]
6. White Balance (HD)
Test Point
Ext. Trigger
Measuring
Range
Input Signal
Input Terminal
Monochrome has a color tint.
DC ma meter
CIRCUIT ADJUST MODE
Activate …….. MEN U-2-4-5-7
Function … ...…… …..AUD IO
Item No. …… ….…….VIDEO
Adjus t Data ….…….AD JU ST
Save Data …. ……… ENTER
Exit ……… …..MEN U (twice)
Measuring
Instrument
To set the CRTs white level in the NTSC mode.
-----------------HD White Raster
DTV Inputs
Symptom:
WS-73517
900ua
900ua
900ua
To set the CRTs white level in the HD mode.
Monchrome pictures have a color tint.
1.
2.
3.
4.
5.
Supply an HD Full White Raster signal to the DTV Inputs.
Select the DTV Inputs (Input button)
Activate the Adjustment mode, VC Function.
Set Item “19 COL” to 0.
Adjust Items “4 RDRH” and “6 BDRH” for optimum white at the center of the
screen.
6. Reduce the input signal luminance to 25%.
7. Adjust Items “7 CTRH” and “9 CTBH” for optimum white.
8. Set the data for Item “19 COL” back to 31.
CIRCUIT ADJUST MODE
Activate …….. MEN U-2-4-5-7
Function … ...…… …..AUD IO
Item No. …… ….…….VIDEO
Adjus t Data ….…….AD JU ST
Save Data …. ……… ENTER
Exit ……… …..MEN U (twice)
Page 29
MODELS: WS-55517 / WS-65517 / WS-73517
[Video Circuit]
Purpose:
To set the black level of the picture.
7. Black Level
Symptom:
Excess or insufficient brightness.
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
------
Input Signal
Monoscope
Input Terminal
1. Supply a Monoscope signal to a Video Input.
2. Activate the Adjust Mode, VC Function.
3. Adjust Item “1 SBRT” so the 0% and 10% black levels on the gradation scale
are the same.
4. Press ENTER to save data.
7. Exit the Service Mode.
Video Input
CIRCUIT ADJUST MODE
Activate …….. MEN U-2-4-5-7
Function … ...…… …..AUD IO
Item No. …… ….…….VIDEO
Adjus t Data ….…….AD JU ST
Save Data …. ……… ENTER
Exit ……… …..MEN U (twice)
40% 30% 20% 10%
50% 0%
0%
0%
60% 70% 80% 90%
GRADATION SCALE
[Video Circuit]
Purpose
To set overall beam current to its’ optimum level.
8. Sub Contrast
Symptom:
Excess or insufficient contrast.
Measuring
Instrument
DC ma meter
Test Point
DT connector pins 7 & 8
Ext. Trigger
------
Measuring
Range
Input Signal
-----
Note: Activate the Expand mode (full screen).
1. Supply a Grayscale signal to a RF Input.
2. Activate the Adjust Mode, VC Function.
3. Select Item “2 SCT”, signal level automatically reduces.
4. Connect a 3ma DC meter between DT connector pins 7 and 8. Positive lead to
pin 7.
5. Adjust Item “1 SCT” to the values given in the Table below.
Input Terminal
RF Input
Grayscale
MODEL
W S-55517
W S-65517 & W S-73517
6. Remove the meter.
7. Save data and Exit the Service Mode.
CIRCUIT ADJUST MODE
Activate …….. MEN U-2-4-5-7
Function … ...…… …..AUD IO
Item No. …… ….…….VIDEO
Adjus t Data ….…….AD JU ST
Save Data …. ……… ENTER
Exit ……… …..MEN U (twice)
Page 30
CURRENT
480 ±ua
525 ±ua
MODELS: WS-55517 / WS-65517 / WS-73517
[Focus Circuit]
Purpose:
9. Dynamic Focus Preset
Symptom: Poor focus at the edges of the screen.
Measuring
Instrument
Test Point
---------
Ext. Trigger
------
Measuring
Range
-----
Input Signal
Monoscope
Input Terminal
Video Input
CONVERGENCE MODE
Activate … …..MEN U-2-4-5-9
Mis c. ……… ……… .… …"6"
C oars e… ……… ……..…."5"
Fine ……… ………… …..."4"
C olor (R ,G or B)…… AUD IO
Item No…… …….…..VIDEO
Adjus t/Move…… ….ADJUST
C urs or Toggle….…..EN TER
Save & Exit…..MEN U (tw ice)
1.
2.
3.
4.
5.
To improve edge focus.
Supply a Monoscope signal to a Video Input
Activate the Convergence Mode.
Select the DF Function under the Conv. Coarse Mode.
Set Items “1 DFH” and “2 DFV” to the data values given in the DF Table.
Exit the Conv. Mode.
DF
Item
1
2
Abbr
DFH
DFV
[Video Circuit]
Purpose
10. Lens Focus
Symptom: Poor focus
Measuring
Instrument
-----
Test Point
------
Ext. Trigger
------
Measuring
Range
Input Signal
-----
Input Terminal
Video Input
Monoscope
Function
Dynamic Focus Horiz.
Dynamic Focus Vert..
MENU-2-4-5-6-5
Data
-450
200
To set the Lens position for optimum focus.
Note: This adjustment must be done before Electrostatic Focus. Perform this
adjustment for RED, GREEN, and BLUE monochrome pictures.
1. Supply a VIDEO signal (Monoscope).
2. Cover the Red and Blue Lens (producing a green raster).
3. Adjust the Green Lens for best focus at the center of the Monoscope pattern.
Note: Attach a white paper to the
screen center. During adjustment,
observe the picture on the screen
from inside for easier adjustment.
4. Repeat Steps 2 and 3 for the Red
and Blue monochrome pictures.
Page 31
MODELS: WS-55517 / WS-65517 / WS-73517
[CRT Circuit]
Purpose:
To set electrostatic focus to the optimum point.
11. Electrostatic Focus &
(Alignment Magnet)
Symptom:
Poor focus.
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
------
Input Signal
Input Terminal
Monscope & Crosshatch
Video Input
Note: This adjustment must be performed after the Sub Contrast adjustment.
Alignment Magnet Adjustment
This adjustment must be performed before Static Focus Adjustment
1. Supply a Crosshatch with Center Dot signal to a Video Input.
2. Set the display format to Standard (Format button)
3. Select a Green raster using the table below.
4. Roughly adjust Green Focus VR.
5. Rotate Green Focus VR CCW so the center dot is about 10mm diameter.
6. Adjust the Green 4 Pole Magnet for the roundest center dot.
7. Set the Green Focus VR for optimum focus.
8. Repeat the procedure with a Red raster and adjust the Red 4 Pole Magnet.
9. Use silicon to lock the magnets in place.
Static Focus Adjustment (All Models)
1. Supply a Monoscope signal to a Video Input
2. Activate A/V Reset
3. Select Red, Green or Blue rasters using the table below.
3. Set the Red, Green and Blue Focus VRs for optimum focus in the center of
the picture.
Ra ste r Color
Color Raster
Red
Green
Blue
Se le ction
Activation Code
MENU-2-4-5-9-1
MENU-2-4-5-9-2
MENU-2-4-5-9-3
[On Screen Display]
Purpose
To position the character display horizontally.
12.Character Position
Symptom:
Incorrect display position
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
Input Signal
------
Input Terminal
ANT-A
1.
2.
3.
4.
Supply an NTSC signal to Ant-A and select Ant-A as the source.
Enter the OSD Position Mode, press “MENU-2-4-8-8”.
Adjust “OSDSD” to center the OSD horizontally.
Press “MENU” to save data and exit the mode.
Video Signal (NTSC)
Page 32
MODELS: WS-55517 / WS-65517 / WS-73517
[Conv/Defl]
Purpose:
To preset data controlling raster geometry
13. Geometry Preset
Symptom:
Raster distortion.
Measuring
Instrument
Test Point
Ext. Trigger
-----
------
Measuring
Range
-----
Input Signal
NTSC & HD
Input Terminal
Procedure
In the Circuit Adjustment and Coarse Convergence Modes preset the data to the
values given in the Tables below.
------
CRT-JNGL
Display
Video & DTV Inputs
CONV GREEN Items
(MENU-2-4-5-9-5)
No. Abbrev. WS-55517 WS-65517 WS-73517
Name
SD
HD
SD HD
SD HD
1
HSTA*
0
0
0
0
0
0
2
VSTA*
0
0
0
0
0
0
3
SKEW
0
0
0
0
0
0
4
TILT
0
0
0
0
0
0
5
HWID
20
20
20
20
20
20
6
HLIN
12
12
12
12
12
12
7
SPCC
0
0
0
0
0
0
8
HKEY
0
0
0
0
0
0
9
TBPC -195 -180 -200 -170 -210 -180
10
VKEY
0
0
0
0
0
0
11
VWID
0
0
0
0
0
0
12
VLIN
0
0
0
0
0
0
CONV RED Items
No.
1
2
7
8
9
13
18
Item
HWID
HKEY
VHGT
VLIN
VSCN
H-POS
V-POS
No. Abbrev. WS-55517
Name
SD
HD
1
HSTA
-50 -50
2
VSTA
0
0
3
SKEW
0
0
4
TILT
0
0
5
HLIN
180 180
6
HWID
0
0
7
VKEY
100 100
8
VWID
0
0
9
VLIN
0
0
10
TPPC
-20 -20
11
HSBW
-30 -30
(MENU-2-4-5-9-5)
WS-65517
WS-73517
HD
25
41
28
6
3
38
31
HD
21
25
33
6
3
38
31
HD
28
25
33
6
3
38
31
SD
25
37
31
6
3
23
31
SD
21
24
38
6
3
23
31
SD
28
24
41
6
3
23
31
CONVERGENCE MODE
Activate … …..MEN U-2-4-5-9
Mis c. ……… ……… .… …"6"
C oars e… ……… ……..…."5"
Fine ……… ………… …..."4"
C olor (R ,G or B)…… AUD IO
Item No…… …….…..VIDEO
Adjus t/Move…… ….ADJUST
C urs or Toggle….…..EN TER
Save & Exit…..MEN U (tw ice)
(MENU-2-4-5-9-5)
WS-65517
SD HD
-50 -50
0
0
0
0
0
0
180 160
0
0
100
70
0
0
0
0
-20 -20
-30 -30
0~63
0~63
0~63
0~15
0~15
0~63
0~63
WS-55517
CIRCUIT ADJUST MODE
Activate …….. MEN U-2-4-5-7
Function … ...…… …..AUD IO
Item No. …… ….…….VIDEO
Adjus t Data ….…….AD JU ST
Save Data …. ……… ENTER
Exit ……… …..MEN U (twice)
No. Abbrev. WS-55517 WS-65517 WS-73517
Name
SD
HD
SD HD
SD HD
1
HSTA
50
50
50
50
10
100
2
VSTA
0
0
0
0
0
0
3
SKEW
0
0
0
0
0
0
4
TILT
0
0
0
0
0
0
5
HLIN
-210 -150 -180 -160 -230 -210
6
HWID
10
10
0
0
0
0
7
VKEY -100 -100 -100 -90 -140 -110
8
VWID
0
0
0
0
0
0
9
VLIN
0
0
0
0
0
0
10
TPPC
20
20
20
20
20
20
11
SDBW
30
30
30
30
30
30
CONV BLUE Items
MENU-2-4-5-7
Data
Range
WS-73517
SD HD
-100 -100
0
0
0
0
0
0
230 200
0
0
70
90
0
0
0
0
-20 -20
-30 -30
Page 33
MODELS: WS-55517 / WS-65517 / WS-73517
[Deflection Circuit]
Purpose:
To set the height, width and linearity of the raster.
14: Deflection Geometry
Height & Width Adjustment
Symptom:
Incorrect height, width and/or linearity.
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
-----
Input Signal
Monoscope (NTSC & HD)
Input Terminal
Video & DTV Inputs
CIRCUIT ADJUST MODE
Activate …….. MEN U-2-4-5-7
Function … ...…… …..AUD IO
Item No. …… ….…….VIDEO
Adjus t Data ….…….AD JU ST
Save Data …. ……… ENTER
Exit ……… …..MEN U (twice)
Note:
Always use the Standard Format when aligning Geometry and Convergence.
Preliminary:
1. DO NOT change the initial values for “#8 VLIN” in the CRT Jungle Function.
2. DO NOT exceed the following VHGT adjustment ranges:
NTSC ... from -4 to +10
HD ... from -10 TO +5
NTSC Mode
1. Supply an NTSC Monoscope signal to a Video Input.
2. Select the Monoscope as the signal source.
3. Activate the Adjustment Mode, CRT-JNGL Function.
4. Select and adjust each of the following items.
• “7 VHGT” ... so the vertical marker sum = 4
• “1 HWD” ... so the horizontal marker sum = 7
5. Save data and Exit the Service Mode.
HD Mode
1. Supply an HD Monoscope signal to the DTV HD Inputs.
2. Select the DTV Inputs as the signal source (Input button)
3. Activate the Service Mode, CRT JNGL Function.
4. Select and adjust each of the following items.
• “7 VHGT” ... so the vertical marker sum = 2
• “1 HWD” ... so the horizontal marker sum = 5
5. Save data and Exit the Service Mode.
Page 34
MODELS: WS-55517 / WS-65517 / WS-73517
[Convergence Circuit]
Purpose:
To set the Convergence circuit geometry adjustments.
15. Convergence Geometry
Adjustment
Symptom:
Raster distortion at the top, bottom or sides of the picture.
Measuring
Instrument
-----
Note: Deflection Circuit Geometry must be performed before this adjustment.
Test Point
------
Ext. Trigger
------
Note:
Always use the Standard Format when aligning Geometry and Convergence.
Measuring
Range
-----
Input Signal
NTSC -- None
HD -- HD sync
Input Terminal
Video & DTV Inputs
NTSC mode
1. Select a Video Input with no signal.
2. Activate the Convergence Mode, Coarse Green.
3. Adjust the Coarse Green Items shown below for straight crosshatch lines.
4. Select the Fine Green Mode, a Cursor is displayed on the crosshatch.
5. Use the Cursor to adjust for straight crosshatch lines.
6. Exit the Convergence Mode.
HD mode
1. Supply an HD signal (sync only) to a Component input and select that
Component Input as the signal source.
2. Repeat NTSC Steps 2 through 6, in the HD mode.
3. Exit the Convergence Mode.
CONVERGENCE MODE
Activate … …..MEN U-2-4-5-9
Mis c. ……… ……… .… …"6"
C oars e… ……… ……..…."5"
Fine ……… ………… …..."4"
C olor (R ,G or B)…… AUD IO
Item No…… …….…..VIDEO
Adjus t/Move…… ….ADJUST
C urs or Toggle….…..EN TER
Save & Exit…..MEN U (tw ice)
Page 35
MODELS: WS-55517 / WS-65517 / WS-73517
[Convergence Circuit]
Purpose:
To converge red, green and blue at the center of the screen
16. Centering and Static
Convergence
Symptom:
Color edging over the entire picture.
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
-----
Input Signal
NTSC -- Monoscope
HD -- Monoscope
Input Terminal
Video & DTV Inputs
CONVERGENCE MODE
Activate … …..MEN U-2-4-5-9
Mis c. ……… ……… .… …"6"
C oars e… ……… ……..…."5"
Fine ……… ………… …..."4"
C olor (R ,G or B)…… AUD IO
Item No…… …….…..VIDEO
Adjus t/Move…… ….ADJUST
C urs or Toggle….…..EN TER
Save & Exit…..MEN U (tw ice)
Preliminary
Degauss the shield cover and bracket unit of the CRT assembly and chassis.
DO NOT degauss the CPM Assemblies.
CAUTION: Do Not adjust the Alignment Magnets instead of the Centering Magnets.
NOTE: Confirm that Item #13 HPOS, in the CRT-DEFL function of the MENU-2-4-5-7
Adjustment mode is set to the following values:
HD=34
SD=23
HD mode (The following steps must be performed in the HD mode)
1. Supply an HD Monoscope signal to the DTV Inputs.
2. Select the DTV Inputs as the signal source (Input button).
3. Enter the Convergence Coarse mode.
4. Set the data for the “HSTA” and “VSTA” items to:
GREEN
RED
BLUE
HSTA = 0
HSTA = 50
HSTA = -50
VSTA = 0
VSTA = 0
VSTA = 0
5. In the Coarse Green mode:
• Center the Green Raster using the Green Centering Magnet.
• Rotate the Green Deflection Yoke to correct any tilt.
6. In the Coarse Red mode, use the Red Centering Magnet to converge
red on the green at the center of screen. Correct any red tilt with the Red
Deflection Yoke.
7. In the Coarse Blue mode, repeat Step 6 using the Blue Centering magnet and
the Blue Deflection Yoke.
8. Exit the Convergence mode.
SD mode
1. Supply an NTSC Monoscope signal to a Video Input.
2. Select the Monoscope as the signal source (Input button).
3. Enter the Convergence Coarse Green mode.
4. Confirm that the Green Raster is centered.
Page 36
MODELS: WS-55517 / WS-65517 / WS-73517
[Convergence Circuit]
Purpose:
17. Coarse Convergence
Symptom:
Measuring
Instrument
-----
Test Point
Note:
Always use the Standard Format when aligning Geometry and Convergence.
------
Ext. Trigger
------
Measuring
Range
-----
Input Signal
NTSC -- None
HD -- HD sync
Input Terminal
Video & HD Inputs
CONVERGENCE MODE
Activate … …..MEN U-2-4-5-9
Mis c. ……… ……… .… …"6"
C oars e… ……… ……..…."5"
Fine ……… ………… …..."4"
C olor (R ,G or B)…… AUD IO
Item No…… …….…..VIDEO
Adjus t/Move…… ….ADJUST
C urs or Toggle….…..EN TER
Save & Exit…..MEN U (tw ice)
To converge red and blue on green at the edges of the
screen.
Color edging at the top, bottom and sides of the screen.
SD mode
1. Select an External Input with no signal.
2. Activate the Convergence Mode, Coarse Red.
3. Adjust the Items shown below to converge the red on the green.
4. Select Coarse Blue mode.
5. Adjust the Items shown below to converge the blue on the green.
Note: If center convergence shifts, use red and blue Items “1 HSTA” and
“2 VSTA” to correct the shift.
6. Exit the Convergence Mode.
HD mode
1. Supply an HD signal (sync only) to a Component input and select that
Component Input as the signal source.
2. Repeat SD Steps 2 through 6, in the HD mode.
3. Exit the Convergence Mode
Page 37
MODELS: WS-55517 / WS-65517 / WS-73517
[Convergence Circuit]
Purpose:
To converge red, green and blue at the edges of the screen
18. Fine Convergence
Symptom:
Color edging at the edges of the picture.
Measuring
Instrument
-----
Test Point
-----
Ext. Trigger
------
Measuring
Range
-----
Input Signal
NTSC -- None
HD -- HD sync
Input Terminal
Video & DTV Inputs
CONVERGENCE MODE
Activate … …..MEN U-2-4-5-9
Mis c. ……… ……… .… …"6"
C oars e… ……… ……..…."5"
Fine ……… ………… …..."4"
C olor (R ,G or B)…… AUD IO
Item No…… …….…..VIDEO
Adjus t/Move…… ….ADJUST
C urs or Toggle….…..EN TER
Save & Exit…..MEN U (tw ice)
Note:
Always use the Standard Format when aligning Geometry and Convergence.
SD Fine Adjustment
1. Select an External Input, no signal.
2. Activate the Convergence Mode, Fine Red.
3. Use the Cursor to converge red on the green.
4. Select the Fine Blue mode.
5. Use the Cursor to converge blue on the green.
6. Exit the Convergence mode.
HD Fine Adjustment
1. Supply an HD signal (sync only) to a Component input and select that
Component Input as the signal source.
2. Repeat SD Fine Adjustment Steps 2 through 6, in the HD mode.
3. Exit the Convergence Mode.
Page 38
MODELS: WS-55517 / WS-65517 / WS-73517
CHIP PARTS REPLACEMENT
Some resistors, shorting jumpers (0 Ohm resistors),
ceramic capacitors, transistors and diodes are chip parts.
The following precautions should be taken when replacing
these parts.
Cautions:
1. Use a fine tipped, well insulated soldering iron
(approximately 30 watts), and tweezers.
2. Melt the solder and remove the chip parts
carefully so as not to tear the copper foil from
the printed circuit board.
3. Discard removed chips; do not reuse them.
4. Do not apply heat for more than 3 (three)
seconds to new chip parts.
5. Avoid using a rubbing stroke when soldering.
6. Take care not to scratch, or damage the chip
parts when soldering.
7. Supplementary cementing is not required.
Chip Parts Removal (Transistors)
1. Melt the solder of one lead and lift the side of
that lead upward.
2. Simultaneously melt the solder of the other
two leads and lift the part from the PCB.
Chip Parts Removal (Resistors, Capacitors, etc.)
1. Grasp the part with tweezers. Melt the solder
at both sides alternately, and remove one side
of the part with a twisting motion.
2. Melt the solder at the other side and remove
the part.
Replacement
1. Presolder the contact points on the circuit
pattern.
2. Press the part downward with tweezers and
apply the soldering iron as shown.
PAGE 39
MODELS: WS-55517 / WS-65517 / WS-73517
REPLACEMENT PARTS
Parts Ordering
To expedite delivery of replacement parts orders, specify the following:
1. Model Number/Serial Number
2. Part Number and description
3. Quantity
Note: Unless complete information is supplied, delay in processing of orders will result.
Critical and Warranty Parts Designation
Critical Electrical Components are indicated by Bold Type in the Parts List, and in the schematic
diagrams by shading.
Warranty Return Parts are indicated in the Parts List with an (*).
Parts Tolerance Codes
Refer to the following chart for tolerance characteristics of electrical components.
MARK
B
C
D
F
G
J
K
Tolerance %
± 0.1
± 0.25
± 0.5
±1
±2
±5
± 10
MARK
M
N
V
X
Z
P
Q
Tolerance %
± 20
± 30
± 10
+ 40
+ 80
+ 100
+ 30
-20
-20
-0
-10
MARK
M
N
V
X
Z
Tolerance (pF)
± 0.1
± 0.25
± 0.5
±1
±2
PAGE 40
MODELS: WS-55517 / WS-65517 / WS-73517
QUICK REFERENCE FOR COMMON REPLACEMENT PARTS
CRT ASSEMBLIES
MODEL
WS-55517
WS-65517
WS-73517
ASSY-CRT [R]
251C330040
251C331010
251C331040
ASSY-CRT [G]
251C330050
251C331020
251C331050
ASSY-CRT [B]
251C330060
251C331030
251C331060
REMOTE CONTROL
290P122010
REMOTE CONTROL
HIGH VOLTAGE / DEFLECTION COMPONENTS
Q5A31
Q5A51
T5A51
261P122010
261P142010
334P288010
129P070020
HORIZ-OUT 2SC5778
HV-OUT2SK2847
TRANS-FLYBACK
VR-FOCUS
338P054010
338P054020
SVM COIL
SVM COIL
WS-55517 / WS-65517
WS-73517
330P294020
453B036010
453B036020
453B036070
453B036080
DEFL-YOKE
CAP-ANODE-[R]
CAP ANODE-[GB]
CAP-ANODE-[R]
CAP ANODE-[GB]
WS-55517 / WS-65517
WS-55517 / WS-65517
WS-73517
WS-73517
MISCELLANEOUS
MODEL
MIRROR
WS-55517
WS-65517
WS-73517
767D072030
767D048090
767C031020
LENTICULAR
SCREEN
491P180010
491P182010
491P185010
PAGE 41
FRESNEL
LENS
491P181010
491P183010
491P186010
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
Part #
Part Name & Description
[#]
TUBES
251C330040
251C330050
251C330060
251C331010
251C331020
251C331030
251C331040
251C331050
251C331060
ASSY-CRT-R(P16LYT03RJA)
ASSY-CRT-G(P16LYT05HKA)
ASSY-CRT-B(P16LYT03BMB)
ASSY-CRT-R(P16LYT03RJA)
ASSY-CRT-G(P16LYT05HKA)
ASSY-CRT-B(P16LYT03BMB)
ASSY-CRT-R(P21LUB05RJA)
ASSY-CRT-G(P21LUB05HKA)
ASSY-CRT-B(P21LUB05BMB)
INTEGRATED CIRCUITS
IC2000
IC2010
IC2020
IC2030
IC2040
IC2050
IC2300
IC2K01
IC2L01
IC2L41
IC2M01
IC2M02
IC2N01
IC2N41
IC2P01
IC2P41
IC2V00
IC2V01
IC3002
IC3003
IC3004
IC3005
IC3006
IC3007
IC3E01
IC3J01
IC4B01
IC5A00
IC5A01
IC5A02
IC5A03
IC5A04
IC6B01
IC6G01
IC6R01
IC7A00
IC7A02
IC7D00
IC7D01
IC7DA1
IC7DB0
IC7DC0
IC7E01
IC7EA0
IC7H00
IC7K21
IC7M00
276P090010
261P829010
275P981010
271P069010
271P072020
271P099010
276P109010
271P061010
271P078010
271P078010
275P947010
272P379020
270P658030
270P703010
270P658030
270P703010
275P733010
271P068010
276P109010
270P938010
275P731020
275P278010
270P838010
270P838010
270P750010
271P060010
270P261020
267P163010
271P068010
271P067010
270P704010
271P062010
270P667010
270P667010
270P667010
276P087010
270P706020
275P278010
270P818020
267P176010
271P072020
271P072040
275P894010
275P663030
276P106010
270P831010
276P091010
IC-C-MOS - SiI9993
TR-CHIP - NDC7002N
IC-C-MOS - 24LCS22AT/SN
IC-C-MOS - CM1210-08MS
IC - LD29150DT33
IC - LD29150PT50R
IC-C-MOS - CS4334-KS
IC - CXA2189Q
IC - MM1566AJBE
IC - MM1566AJBE
IC-C-MOS - UPD64083
IC - LM1881MX (NSC)
IC - CXA2019AQ/T4
IC - BA7657F
IC - CXA2019AQ/T4
IC - BA7657F
IC-C-MOS - CXA2150AQ
IC - LM324AD
IC-C-MOS - CS4334-KS
IC - MC33202D
IC-C-MOS - MSP3445G-QI-B8-V3
IC-C-MOS - TC74LVX14FT
IC-C-MOS - NJM2520M
IC-C-MOS - NJM2520M
IC - LA4663
IC - CXA2188Q
IC - TDA8177
HIC - MSPAD401
IC - LM324AD
IC - LM339AD
IC - LM4040BIZ-10.0
IC - BA9759F
IC - TDA6120Q
IC - TDA6120Q
IC - TDA6120Q
IC-C-MOS - M306V7MG-086FP
IC - MAX823REUK
IC-C-MOS - TC74LVX14FT
IC - CXA3506R
HIC - AF-9412
IC - LD29150DT33
IC - LD29150DT18R
IC-C-MOS - AD9883AKST-110
IC-C-MOS - M4A3-32/32-5VC-48
IC-C-MOS - MB87M1823PFV-ES-BND
IC-C-MOS - OPA2350PA
IC-C-MOS - M12L64322A-6T
a
a
a
b
b
b
c
c
c
Ref #
IC7N00
IC7P01
IC7P02
IC7P03
IC7Q01
IC8001
IC8002
IC8003
IC80E1
IC80E2
IC80E3
IC8101
IC8102
IC8103
IC81A1
IC81A2
IC81A3
IC81A4
IC81A5
IC81A6
IC81A7
IC81A8
IC8205
IC8211
IC8212
IC8280
IC8301
IC8302
IC8303
IC8305
IC8307
IC8309
IC8310
IC8312
IC8313
IC8314
IC8315
IC8401
IC8402
IC8501
IC8502
IC8503
IC8504
IC8505
IC8506
IC8507
IC8508
IC8509
IC8708
IC8709
IC8710
IC8719
IC8720
IC8721
IC8800
IC8801
IC8802
IC8805
IC8806
IC8C01
PAGE 42
Part #
270P997010
275P943030
271P023010
263P154010
275P533010
276P030030
270P706020
276P064010
275P657050
276P174010
270P880010
271P033010
276P029020
276P029020
270P991010
261P135010
270P879030
270P992010
270P879030
270P037020
270P999010
271P081010
276P042010
276P029020
276P029020
275P955010
275P677010
275P677010
275P677010
275P956010
275P983020
275P660020
275P270010
270P938010
275P731020
275P677010
275P464010
275P624010
275P686010
275P679010
275P124040
275P677010
271P036020
275P677010
276P065020
275P680010
275P675010
271P036020
271P072030
271P082010
271P072010
271P023010
271P023010
270P677030
270P877010
270P877010
275P464010
271P064010
271P039010
267P173010
Part Name & Description
IC-C-MOS - SM5301AS
IC-C-MOS - PIC18F252T-I/SO030
IC - SN74CBTD1G125DBVR
IC-C-MOS - SN74HC132DB
IC-C-MOS - M24C64WM6T
IC-C-MOS - 215H31AGA12H
IC - MAX823REUK
IC-C-MOS - SN74LVC1G125DBV
IC-C-MOS - 24LC256T-I/SN
IC-C-MOS - AT24C512N-10S1-2.7
IC - 24LC64I/SN
IC - LP2996MRX
IC-C-MOS - NT5DS16M16BT-5T
IC-C-MOS - NT5DS16M16BT-5T
IC - IRU3037CS
FET-HEX - IRF7313
IC - SC1566I5M-2.5TR
IC - BA18BC0FP
IC - SC1566I5M-2.5TR
IC - MIC29301-5.0BU
IC - NJM2370R09
IC - BA00CC0WFP
IC-C-MOS - MIC2544-1BM
IC-C-MOS - NT5DS16M16BT-5T
IC-C-MOS - NT5DS16M16BT-5T
IC-C-MOS - RTC-8564JE
IC-C-MOS - SN74LVC573APWR
IC-C-MOS - SN74LVC573APWR
IC-C-MOS - SN74LVC573APWR
IC-C-MOS - MD2811-D16-V3
IC-C-MOS - ST16C650ACQ48
IC-C-MOS - CS4341-KSR
IC-C-MOS - M66010GP
IC - MC33202D
IC-C-MOS - MSP3445G-QI-B8-V3
IC-C-MOS - SN74LVC573APWR
IC-C-MOS - TC7WH14FK
IC-C-MOS - TSB42AA4
IC-C-MOS - TSB41AB3PFP
IC-C-MOS - TC74LCX74FT
IC-C-MOS - SN74LVC245APWR
IC-C-MOS - SN74LVC573APWR
IC - TPS2221PWPR
IC-C-MOS - SN74LVC573APWR
IC-C-MOS - CIMAX(103563)
IC-C-MOS - TC74VCX257FT
IC-C-MOS - SN74LV125APWR
IC - TPS2221PWPR
IC - LD29150DT50
IC - LD1117DT12
IC - LD29150DT25
IC - SN74CBTD1G125DBVR
IC - SN74CBTD1G125DBVR
IC - BAO9FP
IC - UPC3217GV
IC - UPC3217GV
IC-C-MOS - TC7WH14FK
IC - TA75S01F
IC-C-MOS - NXT2003 100C
HIC - STK394-250
[#]
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
Part #
Part Name & Description
IC8C02
IC8D00
IC8D01
IC8E00
IC8E01
IC8E02
IC8E03
IC9A20
IC9A21
IC9A50
IC9C01
IC9C02
IC9C03
IC9C04
IC9C05
IC9C21
IC9C41
IC9C61
IC9M01
IC9M02
267P173010
276P088010
275P222020
270P751010
270P751010
270P751010
275P721020
267P175010
270P816020
267P161010
271P071020
271P099010
271P099010
271P071010
271P071020
271P072020
271P072030
271P072010
270P677010
270P992020
HIC - STK394-250
IC-C-MOS - CM0038AF
IC-C-MOS - M24C32MN6T
IC - TL084CD
IC - TL084CD
IC - TL084CD
IC-C-MOS - CD0031CM
HIC - STR-W6735
IC - TL431ACLPR
HIC - STR-F6428S
IC - BA09SFP
IC - LD29150PT50R
IC - LD29150PT50R
IC - BA033SFP
IC - BA09SFP
IC - LD29150DT33
IC - LD29150DT50
IC - LD29150DT25
IC - BA033FP
IC - BA25BC0FP
[#]
TRANSISTORS
Conventional
Part #
260C004020
261P149010
260C416030
260C255040
261P122010
261P155010
261P150010
260P630010
261P151010
261P142010
260C001040
260C001040
260C001040
260C001060
260C001030
260C001060
260P644040
260P647040
260C004050
261P151010
260C004010
261P151010
Transistors (By Ref #)
Part Name & Description
TR - 2SC1740S-R,S/2SC3311A-R,S
TR - 2SJ585LS
TR - 2SC2274-F/2SC2274K-F
TR - 2SA950-Y
TR - 2SC5778
TR - 2SK2169
TR - 2SA1207
TR - 2SD2012
TR - 2SC2909
TR - 2SK2847
TR - 2SC2603-G/2SC1740S-E
TR - 2SC2603-G/2SC1740S-E
TR - 2SC2603-G/2SC1740S-E
TR - 2SA1115-F/2SA933S-S
TR - 2SC2603-F,G/2SC1740S
TR - 2SA1115-F/2SA933S-S
TR - 2SA1535-R
TR - 2SC3944-R
TR - 2SA933S-R,S/2SA1309A-R,S
TR - 2SC2909
TR - 2SC1740S-R,S/2SC3311A-R,S
TR - 2SC2909
Part #
Part Name & Description
Q5K05
Q5K06
Q5K07
Q5K08
Q5K09
Q5K50
Q6B01
Q6B02
Q6B03
Q6G01
Q6R01
Q7K21
Q7P22
Q8701
Q9A21
Q9A50
261P150010
261P152010
261P152010
260C004050
261P214010
261P214010
260C001010
260C001050
260C001050
260C001010
260C001010
260C004010
261P114010
261P026010
260P630010
260C416030
TR - 2SA1207
TR - 2SC3116
TR - 2SC3116
TR - 2SA933S-R,S/2SA1309A-R,S
TR - 2SC4634LS
TR - 2SC4634LS
TR - 2SC2603-E,F
TR - 2SA1115-E,F/2SA933S
TR - 2SA1115-E,F/2SA933S
TR - 2SC2603-E,F
TR - 2SC2603-E,F
TR - 2SC1740S-R,S/2SC3311A-R,S
TR - 2SA1585STPR
TR - 2SC3356
TR - 2SD2012
TR - 2SC2274-F/2SC2274K-F
D2760
D2761
D2770
D2771
D2W01
D2W02
D2W03
D2W04
D4B01
D4B04
D4B05
D5A01
D5A02
D5A03
D5A04
D5A05
D5A06
D5A12
D5A13
D5A14
D5A33
D5A34
D5A35
D5A36
D5A37
D5A51
D5A52
D5A53
D5A54
D5A55
D5A56
D5A57
D5A58
D5A60
D5H01
D5H02
D5K00
D5K01
D6B00
D6B07
D6B08
D6G00
264P828010
264P828010
262P805050
264P828010
264P828010
264P828010
264P828010
264P828010
264D056020
264P828010
264P828010
264P045080
264P045080
264P045080
264P045080
264P466040
262P085010
264P045080
264P045080
264P045080
262P129010
264P460060
264P045080
264P045080
264D056020
262P039010
264P899010
264P466040
262P085010
262P085010
264P045080
262P085010
264P045080
264P463040
264P045080
264P045080
262P150010
262P150010
262P063010
262P063010
262P063010
262P063010
DIODES
TR-CHIP Type (By Part #)
Part No.
Generic No.
260P806010 DTA124EK/UN2112
260P817030 2SA1037K-S
260P817050 2SA1037K-R,S/2SB709AI-R,S
260P817080 2SA1037K-R,S
260P818010 2SC2412K-Q
260P818030 2SC2412K-S
260P818050 2SC2412K-R,S/2SD601AI-R,S
260P818080 2SC2412K-R,S
260P836090 2SC3326-A,B
260P846030 DTC143ZKAT146
261P801010 2SA1252-5,6
Ref #
Q2V30
Q5A04
Q5A07
Q5A09
Q5A31
Q5A32
Q5A34
Q5A36
Q5A41
Q5A51
Q5H03
Q5H04
Q5H05
Q5H06
Q5H09
Q5H10
Q5H11
Q5H12
Q5K01
Q5K02
Q5K03
Q5K04
Ref #
[#]
PAGE 43
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
D-CHIP - UDZS5.1B
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
DIODE - S5500D/EM1Z/ERB12-02RK
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - EQA02-15AB/RD16EB1
DIODE - 11EFS2N-TA2B5
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 30PRA20-FC5
DIODE - EQA02-05C/RD5.1EB1
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - S5500D/EM1Z/ERB12-02RK
DIODE - BYW96E/20
DIODE - BYV26E
DIODE - EQA02-15AB/RD16EB1
DIODE - 11EFS2N-TA2B5
DIODE - 11EFS2N-TA2B5
DIODE - 1S2076A/1S2471OM
DIODE - 11EFS2N-TA2B5
DIODE - 1S2076A/1S2471OM
DIODE - RD9.1EB1
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - RL153 (Pb-free)
DIODE - RL153 (Pb-free)
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
[#]
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
Part #
Part Name & Description
D6G07
D6G08
D6R00
D6R07
D6R08
D7K21
D7K22
D7L41
D7R03
D81A1
D81A2
D81A3
D81A4
D81A5
D8201
D8202
D8203
D8204
D8280
D8800
D8802
D8803
D8805
D8C03
D8C04
D9A01
D9A02
D9A03
D9A04
D9A20
D9A21
D9A22
D9A23
D9A24
D9A25
D9A26
D9A27
D9A28
D9A29
D9A30
D9A31
D9A50
D9A51
D9A52
D9A53
D9A54
D9A55
D9A56
D9A57
D9A58
D9A60
D9A61
D9A68
D9A69
262P063010
262P063010
262P063010
262P063010
262P063010
268P100010
264P045080
264P212020
264P828010
264P828010
264P828010
264P828010
262P090010
264P458050
264P846010
264P846010
264P846010
264P846010
264P808010
262P089010
262P071070
262P071070
262P089010
262P817010
262P817010
262P031010
264P045080
264P461050
264P045080
264P045080
264P899010
264P825040
262P085010
264P045080
262P085010
262P083010
262P127010
264P045080
264P045080
264P470070
264P045080
264P045080
264P045080
264P045080
264P045080
262P085010
264P045080
262P083010
264P899010
262P088010
262P129010
262P129010
264P469070
264P527020
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
DIODE - 1SS244
DIODE-PHOTO - SFH235FA
DIODE - 1S2076A/1S2471OM
D-LED - LN31GPH
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
D-CHIP - DAN202U/MA142WK
DIODE - M1FP3
DIODE - RD3.9EB1
DIODE-CHIP - MA732
DIODE-CHIP - MA732
DIODE-CHIP - MA732
DIODE-CHIP - MA732
DIODE-CHIP - DAN202K
DIODE - MA2S728
DIODE-LE - SML-210FT
DIODE-LE - SML-210FT
DIODE - MA2S728
DIODE-CHIP - PTZ9.1B
DIODE-CHIP - PTZ9.1B
DIODE - D6SB80
DIODE - 1S2076A/1S2471OM
DIODE - EQA02-06B/RD5.6EB3
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - BYV26E
DIODE - ERA15-08
DIODE - 11EFS2N-TA2B5
DIODE - 1S2076A/1S2471OM
DIODE - 11EFS2N-TA2B5
DIODE - FSF05A20
DIODE - FSH05A03L
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - EQA02-32B/RD33EB3
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 1S2076A/1S2471OM
DIODE - 11EFS2N-TA2B5
DIODE - 1S2076A/1S2471OM
DIODE - FSF05A20
DIODE - BYV26E
DIODE - 31DF4-FC5
DIODE - 30PRA20-FC5
DIODE - 30PRA20-FC5
DIODE - EQA02-28A/RD27EB4
DIODE - AK04
L1H01
L1H02
L1H51
L1H52
321C114010
325C461030
321C114010
325C461030
COILS
COIL-RF - 2200MH-J
COIL-PEAKING - 10MH-K
COIL-RF - 2200MH-J
COIL-PEAKING - 10MH-K
[#]
Ref #
Part #
Part Name & Description
L2011
L2012
L2061
L2071
L2111
L2121
L2141
L2151
L2231
L2271
L2300
L2301
L2311
L2321
L2331
L2341
L2711
L2721
L2761
L2801
L2821
L2K01
L2K09
L2K58
L2K67
L2K71
L2L01
L2L61
L2M21
L2M31
L2M35
L2M36
L2M38
L2M40
L2M41
L2M45
L2M46
L2M50
L2M53
L2M70
L2M71
L2M77
L2M81
L2N03
L2N25
L2N60
L2P03
L2P25
L2P60
L2V19
L2V55
L2V61
L2W02
L2W03
L2W04
L3020
L3034
L3048
L3049
L3050
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P865020
409P923060
409P865020
409P865020
409P865020
409P865020
409P865020
409P865020
409P865020
409P777080
409P777080
409P777080
325C461030
325C461030
325C461030
325C461030
325C461030
325C461030
325C461030
325C461030
409P777080
325C461050
325C461030
409P777080
325C461030
325C461030
409P777080
409P777080
325C461000
325C461030
325C461030
325C461030
325C461030
409P777080
325C461030
409P777080
409P777080
325C461030
409P777080
409P777080
325C461010
325C461010
325C461010
409P923060
409P923060
409P923060
409P923060
409P923060
409P923060
409P923060
409P923060
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 15MH-K
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 5.6MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 6.8MH-K
COIL-PEAKING - 6.8MH-K
COIL-PEAKING - 6.8MH-K
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
PAGE 44
[#]
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
L3054
L4B01
L5A01
L5A02
L5A03
L5A22
L5A34
L5A51
L5A54
L7A16
L7A19
L7A88
L7A90
L7A91
L7A99
L7D16
L7DA7
L7DF4
L7DF8
L7E34
L7E42
L7E69
L7EB7
L7H01
L7H04
L7H23
L7H29
L7H49
L7H66
L7H76
L7H95
L7H96
L7J13
L7J23
L7J38
L7J44
L7K01
L7M90
L7N24
L7P14
L7P20
L7Q31
L7R08
L8001
L8002
L8003
L8004
L8005
L8006
L8007
L8008
L8009
L8012
L8013
L81A1
L81A2
L81A3
L81A4
L81A5
L81A6
Part #
409P923060
321C140060
321C141070
411D009020
411D009020
333P059020
321C140060
321C151010
411D009020
409P777050
409P777050
409P777050
409P777050
409P777050
409P777050
325C420070
325C420070
409P777080
325C420070
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P777080
409P865020
409P865020
409P777080
325C420070
409P777080
409P777080
325C121030
409P777080
325C420070
409P777050
409P777050
409P777080
409P777050
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P777080
409P865080
409P865080
321C140060
351P250010
409P777080
321C140060
321C140060
409P777080
Part Name & Description
EMI-F-CHIP - BLM21B272S
COIL-RF - 2.7MH-M
COIL-RF - 22MH-K
CORE-FERRITE - ZBF503D-01
CORE-FERRITE - ZBF503D-01
COIL-HORIZ-LIN
COIL-RF - 2.7MH-M
COIL-RF - 6.8MH-M
CORE-FERRITE - ZBF503D-01
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
COIL-CHIP - 10MH-K
COIL-CHIP - 10MH-K
EMI-F-CHIP - BLM21P221S
COIL-CHIP - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM21P221S
COIL-CHIP - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
COIL-CHIP - 10MH-K
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21B201S
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
COIL-RF - 2.7MH-M
COIL-CHOKE - GSTC6018-100M
EMI-F-CHIP - BLM21P221S
COIL-RF - 2.7MH-M
COIL-RF - 2.7MH-M
EMI-F-CHIP - BLM21P221S
[#]
Ref #
Part #
Part Name & Description
L81A7
L81A8
L8202
L8203
L8204
L8205
L8206
L8207
L8280
L8301
L8304
L8305
L8307
L8313
L8314
L8315
L8316
L8320
L8321
L8322
L8323
L8324
L8326
L8329
L8331
L8332
L8333
L8401
L8403
L8404
L8411
L8412
L8413
L8414
L8415
L8416
L8501
L8502
L8503
L8504
L8505
L8506
L8507
L8508
L8509
L8510
L8511
L8512
L8701
L8702
L8703
L8704
L8706
L8711
L8717
L8718
L8723
L8725
L8726
L8727
409P865080
409P777080
409P777080
409P777080
409P777080
409P777080
351P265010
351P265010
409P865080
409P865080
325C501010
325C501010
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P865080
409P777080
409P777080
351P265020
351P265020
351P265020
351P265020
351P265020
351P265020
409P865080
409P777080
409P865080
409P777080
409P865080
409P777080
409P865080
409P865080
409P865080
409P777080
409P777080
409P777080
409P923060
409P923060
409P923060
409P923060
409P923060
325C414030
409P923060
409P923060
409P923060
409P923060
409P923060
409P923060
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-CHOKE-CHIP - ACM2012
COIL-CHOKE-CHIP - ACM2012
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
COIL-CHIP - ALQM21NNR47K10
COIL-CHIP - ALQM21NNR47K10
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-CHIP - ACM2012-201-2P
COIL-CHIP - ACM2012-201-2P
COIL-CHIP - ACM2012-201-2P
COIL-CHIP - ACM2012-201-2P
COIL-CHIP - ACM2012-201-2P
COIL-CHIP - ACM2012-201-2P
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM18PG6
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
COIL-CHIP - 0.22MH-J
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
PAGE 45
[#]
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
L8736
L8802
L8803
L8804
L8805
L8808
L8809
L8810
L8811
L8814
L8815
L8824
L8C01
L8C02
L8D01
L8D02
L8D03
L8D04
L8D05
L8D06
L8D07
L8D08
L8D09
L8G00
L8G01
L9A21
L9A22
L9A23
L9A50
L9A51
L9A52
L9A53
L9A54
L9A55
L9A56
L9A57
L9A62
L9A63
L9A64
L9D00
L9D01
LC2H40
LC2H41
LC2H42
LC2H43
LC2H44
LC2H45
LC81A1
LC8301
LC8302
LC8303
LC8304
LC8305
LC8306
LC8307
LC8308
LC8309
LC8310
LC8311
LC8312
Part #
Part Name & Description
409P923060
409P923060
409P923060
409P923060
409P923060
409P923060
325C410040
409P923060
409P923060
325C141070
409P923060
409P923060
321C141070
321C141070
409P777080
409P777080
409P777080
409P777080
325C461030
409P777080
409P777080
325C461030
325C461030
409P777080
409P777080
321C141010
321C141030
321C141030
411D009020
321C141010
411D009020
321C141010
411D009020
321C142030
411D009020
321C141010
321C141010
321C141070
321C141070
351P266010
351P266010
409P777020
409P777020
409P777020
409P777020
409P777020
409P777020
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
COIL-CHIP - 1.8MH-J
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
COIL-CHIP - 22MH-K/J
EMI-F-CHIP - BLM21B272S
EMI-F-CHIP - BLM21B272S
COIL-RF - 22MH-K
COIL-RF - 22MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-PEAKING - 10MH-K
COIL-PEAKING - 10MH-K
EMI-F-CHIP - BLM21P221S
EMI-F-CHIP - BLM21P221S
COIL-RF - 6.8MH-M
COIL-RF - 10MH-K
COIL-RF - 10MH-K
CORE-FERRITE - ZBF503D-01
COIL-RF - 6.8MH-M
CORE-FERRITE - ZBF503D-01
COIL-RF - 6.8MH-M
CORE-FERRITE - ZBF503D-01
COIL-RF - 68MH-K
CORE-FERRITE - ZBF503D-01
COIL-RF - 6.8MH-M
COIL-RF - 6.8MH-M
COIL-RF - 22MH-K
COIL-RF - 22MH-K
LINE-FILTER - ELF22V050BN
LINE-FILTER - ELF22V050BN
EMI-F-CHIP - BLM21A05
EMI-F-CHIP - BLM21A05
EMI-F-CHIP - BLM21A05
EMI-F-CHIP - BLM21A05
EMI-F-CHIP - BLM21A05
EMI-F-CHIP - BLM21A05
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
[#]
Ref #
LC8313
LC8314
LC8315
LC8316
LC8317
LC8318
LC8319
LC8501
LC8502
LC8503
LC8504
LC8505
LC8506
LC8507
LC8508
LC8509
LC8511
LC8512
LC8514
LC8515
LC8516
LC8517
LC8518
LC8519
LC8520
LC8521
LC8522
LC8523
LC8524
LC8525
LC8526
LC8527
LC8528
LC8529
LC8530
LC8531
LF7D02
LF7D04
LF7D06
LF7D08
LF7D10
LF7D12
LF7D14
LF7D16
LF7D18
LF7D20
LF7D22
LF7D24
LF7H02
LF7H04
LF7H06
LF7H08
LF7H10
LF7H13
LF7H14
LF7H18
LF7H20
LF7H22
LF7H24
PAGE 46
Part #
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P945010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P944010
409P865020
409P865020
409P865020
409P865020
409P865020
409P865020
Part Name & Description
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP506X13CD
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - NFL21SP107X1
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
EMI-F-CHIP - BLM11A601S
[#]
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
Part #
Part Name & Description
[#]
Ref #
TRANSFORMERS
T2830
T2860
T2910
T2961
T5A31
T5A32
T5A51
T5K01
T9A20
T9A50
409P961010
409P961010
409P961010
409P961010
349P223010
349P224010
334P288010
349P222020
350P819010
350P818010
103P491070
103P502010
103P491080
103P502020
103P502030
103P502040
103P492000
103P492010
103P492020
103P492030
103P492050
103P492060
103P502050
103P502060
103P402070
103P472090
103P492090
103P502070
103P502080
CHIP-FILTER - ACM2012D-9002P
CHIP-FILTER - ACM2012D-9002P
CHIP-FILTER - ACM2012D-9002P
CHIP-FILTER - ACM2012D-9002P
TRANS-HORIZ
TRANS-HORIZ-DRIVE
TRANS-FLYBACK
TRANS-DBF
TRANS-PWR - ER28TM112
TRANS-PWR - ER42TM051
VARIABLE RESISTORS
129P070020 VR-FOCUS - MT021101-189-2
RV9D00 265P100020 VAR - ERZV10D271CS
RESISTORS
R-CHIP Type
Part No.
103P409050
103P509050
103P508040
103P509000
103P500010
103P793020
103P400050
103P500050
103P500060
103P500070
103P793080
103P500080
103P500090
103P794010
103P501000
103P501010
103P489090
103P509090
103P794060
103P501020
103P794080
103P401030
103P490010
103P501030
103P501040
103P401050
103P501050
103P810050
103P501060
103P490080
103P481070
103P501070
103P471010
103P491020
103P491030
103P501090
103P491040
103P491050
Part No.
103P502000
(By value)
Value
1/8W 0OHM
1/16W 0OHM
1/16W 2.2-J
1/16W 6.8-J
1/16W 10-J
1/16W 20F
1/10W 22-J
1/16W 22-J
1/16W 27-J
1/16W 33-J
1/16W 36F
1/16W 39-J
1/16W 47-J
1/16W 47-F
1/16W 56-J
1/16W 68-J
1/4W 75-J
1/16W 75-J
1/16W 75-F
1/16W 82-J
1/16W 91F
1/10W 100-J
1/16W 100F
1/16W 100-J
1/16W 120-J
1/10W 150-J
1/16W 150-J
1/16W 150-D
1/16W 180-J
1/16W 200-F
1/4W 220-J
1/16W 220-J
1/8W 270-F
1/16W 300-F
1/16W 330-F
1/16W 330-J
1/16W 360-F
1/16W 390-F
Value
1/16W 390-J
Part No.
103P493020
103P493030
103P502090
103P493040
103P493050
103P503000
103P493060
103P493070
103P503010
103P503020
103P494000
103P494010
103P503030
103P494020
103P494030
103P503040
103P814040
103P494050
103P503050
103P494070
103P503060
103P494080
103P503070
103P494090
103P495010
103P503080
103P495020
103P495030
103P503090
103P495040
103P495050
103P504000
103P495070
103P504010
103P495080
103P495090
103P496000
103P496010
Part No.
103P504030
Part #
Value
1/16W 2K-F
1/16W 2.2K-F
1/16W 2.2K-J
1/16W 2.4K-F
1/16W 2.7K-F
1/16W 2.7K-J
1/16W 3K-F
1/16W 3.3K-F
1/16W 3.3K-J
1/16W 3.9K-J
1/16W 4.3K-F
1/16W 4.7K-F
1/16W 4.7K-J
1/16W 5.1K-F
1/16W 5.6K-F
1/16W 5.6K-J
1/16W 6.2K-D
1/16W 6.8K-F
1/16W 6.8K-J
1/16W 8.2K-F
1/16W 8.2K-J
1/16W 9.1K-F
1/16W 10K-J
1/16W 10K-F
1/16W 12K-F
1/16W 12K-J
1/16W 13K-F
1/16W 15K-F
1/16W 15K-J
1/16W 16K-F
1/16W 18K-F
1/16W 18K-J
1/16W 22K-F
1/16W 22K-J
1/16W 24K-F
1/16W 27K-F
1/16W 30K-F
1/16W 33K-F
Value
1/16W 33K-J
Ref #
R2J03
R2J05
R2J07
R2V96
R3E09
R3E11
R3E12
R3E14
R4B04
R4B10
R4B12
R4B16
R4B18
R4B23
R5A16
R5A20
R5A26
R5A32
R5A34
R5A35
R5A36
R5A37
R5A38
R5A39
R5A45
R5A46
R5A50
R5A62
R5A64
R5A65
R5A80
R5A82
R5A85
R5A87
R5A90
R5A93
R5A94
PAGE 47
Conventional
Part #
103P719090
103P719090
103P719090
109D151050
109D151010
109D151010
109D151010
109D151010
103C178060
103C188040
103C188040
109P095010
103P338020
109D151080
103P144010
103P144050
103P761030
103P145030
103P143070
103P143030
103P143070
103C393010
103C187020
103P140090
109D151090
103C391050
103P711000
103P711070
103P712010
103P141030
109P180010
103P370090
109D151030
103P142060
103P711060
103P140090
103C390060
Part Name & Description
1/16W 470-F
1/16W 470-J
1/16W 510-F
1/16W 560-J
1/16W 680-J
1/16W 820-J
1/16W 620-F
1/16W 680-F
1/16W 750-F
1/16W 820-F
1/16W 1K-F
1/16W 1.1K-F
1/16W 1K-J
1/16W 1.2K-J
1/8W 1.5K-J
1/8W 1.5K-F
1/16W 1.5K-F
1/16W 1.5K-J
1/16W 1.8K-J
103P496040
103P496050
103P504050
103P504060
103P496080
103P496090
103P504070
103P504080
103P497030
103P497070
103P498020
103P504090
103P505000
103P505030
103P505050
103P505070
103P505090
103P506000
103P506010
103P506070
Resistors (By Ref #)
Part Name & Description
R-CARBON - 1/4W 75-J
R-CARBON - 1/4W 75-J
R-CARBON - 1/4W 75-J
R-CARBON - 1/4W 75-J
R-CARBON - 1/4W 2.2-J
R-CARBON - 1/4W 2.2-J
R-CARBON - 1/4W 2.2-J
R-CARBON - 1/4W 2.2-J
R-METAL - 1W 3.3-J
R-METAL - 2W 2.2-J
R-METAL - 2W 2.2-J
R-METAL-LIN - 1/4W 5.1K-J
R-CARBON-25 - 1/4W 1.5-J
R-CARBON - 1/4W 220-J
R-CARBON - 1/2W 22K-J
R-CARBON - 1/2W 47K-J
R-FUSE - 1/2W 100-J
R-CARBON - 1/2W 220K-J
R-CARBON - 1/2W 10K-J
R-CARBON - 1/2W 4.7K-J
R-CARBON - 1/2W 10K-J
R-METAL-P - 3W 3.3K-J
R-METAL - 2W 0.22-J
R-CARBON - 1/2W 47-J
R-CARBON - 1/4W 33-J
R-METAL-P - 3W 150-J
R-CARBON - 1/4W 56-J
R-CARBON - 1/4W 220-J
R-CARBON - 1/4W 470-J
R-CARBON - 1/2W 100-J
R-WIRE - 2W 0.16-G
R-FUSE - 1/4W 47-J
R-CARBON - 1/4W 4.7-J
R-CARBON - 1/2W 1.2K-J
R-CARBON - 1/4W 180-J
R-CARBON - 1/2W 47-J
R-METAL-P - 3W 27-J
[#]
1/16W 43K-F
1/16W 47K-F
1/16W 47K-J
1/16W 56K-J
1/16W 62K-F
1/16W 68K-F
1/16W 68K-J
1/16W 82K-J
1/16W 100K-F
1/16W 150K-F
1/16W 240K-F
1/16W 100K-J
1/16W 120K-J
1/16W 220K-J
1/16W 330K-J
1/16W 470K-J
1/16W 680K-J
1/16W 820K-J
1/16W 1M-J
1/16W 3.3M-J
[#]
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
R5B04
R5H02
R5H07
R5H11
R5H12
R5H13
R5H16
R5H17
R5H47
R5H49
R5H50
R5H55
R5H56
R5H58
R5H59
R5H60
R5H67
R5K00
R5K01
R5K02
R5K03
R5K04
R5K05
R5K06
R5K07
R5K08
R5K09
R5K10
R5K11
R5K12
R5K13
R5K15
R5K16
R5K17
R5K18
R5K19
R5K20
R5K21
R5K22
R5K23
R5K24
R5K25
R5K26
R5K27
R5K28
R5K29
R5K30
R5K31
R5K32
R5K33
R5K34
R5K35
R5K36
R5K37
R5K38
R5K50
R5K51
R5K52
R6B01
R6B02
Part #
Part Name & Description
103P711030
103P758000
103P461060
103P712020
103P712020
103P712020
103P710020
103P710020
103C392010
103P714070
103P714070
103P140070
103P140070
103P148000
103C191050
103C178080
103P148000
103P760060
103P760060
103P143070
103P143070
103P760060
103P712080
103P712030
109D151090
103P712050
109D151090
109D031070
103P713070
103P711030
103P712030
103P144070
103P143070
103P145050
103P145050
103P145050
103P145050
103P712050
103P714010
103P713070
103P713050
103P712090
103P713040
103P713040
103P143070
103P146010
103P146010
103P713070
103P714090
103P711080
103P143020
109D151030
109D151030
109D151090
109D151090
103P713070
103P713070
109D031090
103P711030
103P713090
R-CARBON - 1/4W 100-J
R-FUSE - 1/4W 1-J
R-METAL - 1/4W 430-F
R-CARBON - 1/4W 560-J
R-CARBON - 1/4W 560-J
R-CARBON - 1/4W 560-J
R-CARBON - 1/4W 12-J
R-CARBON - 1/4W 12-J
R-METAL-P - 3W 470-J
R-CARBON - 1/4W 68K-J
R-CARBON - 1/4W 68K-J
R-CARBON - 1/2W 33-J
R-CARBON - 1/2W 33-J
R-CARBON - 1/2W 1-J
R-METAL - 3W 150-J
R-METAL - 1W 4.7-J
R-CARBON - 1/2W 1-J
R-FUSE - 1/2W 27-J
R-FUSE - 1/2W 27-J
R-CARBON - 1/2W 10K-J
R-CARBON - 1/2W 10K-J
R-FUSE - 1/2W 27-J
R-CARBON - 1/4W 1.8K-J
R-CARBON - 1/4W 680-J
R-CARBON - 1/4W 33-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 33-J
R-COMP - 1/2W 10K-K
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 680-J
R-CARBON - 1/2W 68K-J
R-CARBON - 1/2W 10K-J
R-CARBON - 1/2W 330K-J
R-CARBON - 1/2W 330K-J
R-CARBON - 1/2W 330K-J
R-CARBON - 1/2W 330K-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 22K-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 6.8K-J
R-CARBON - 1/4W 2.2K-J
R-CARBON - 1/4W 5.6K-J
R-CARBON - 1/4W 5.6K-J
R-CARBON - 1/2W 10K-J
R-CARBON - 1/2W 1M-J
R-CARBON - 1/2W 1M-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 100K-J
R-CARBON - 1/4W 270-J
R-CARBON - 1/2W 3.9K-J
R-CARBON - 1/4W 4.7-J
R-CARBON - 1/4W 4.7-J
R-CARBON - 1/4W 33-J
R-CARBON - 1/4W 33-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 10K-J
R-COMP - 1/2W 470K-K
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 15K-J
[#]
Ref #
R6B03
R6B04
R6B05
R6B06
R6B07
R6B08
R6B09
R6B10
R6B11
R6B13
R6B15
R6B16
R6B17
R6B18
R6B19
R6B20
R6B21
R6B22
R6B23
R6B24
R6B25
R6B26
R6B27
R6B31
R6G01
R6G02
R6G03
R6G04
R6G05
R6G06
R6G07
R6G08
R6G09
R6G10
R6G11
R6G13
R6G15
R6G16
R6G17
R6G20
R6G21
R6G22
R6G23
R6G31
R6R01
R6R02
R6R03
R6R04
R6R05
R6R06
R6R07
R6R08
R6R09
R6R10
R6R11
R6R13
R6R15
R6R16
R6R17
R6R20
PAGE 48
Part #
103P464020
103P713000
103P411010
103P462050
103P711030
103P710010
103P711030
103P713030
103C194020
103P331030
103P714090
103P411000
101P221030
103P713040
103P713050
101P221030
103P467030
103P467030
103P711030
103P713030
103P711030
103P713050
103P711030
103P712060
103P711030
103P713090
103P464020
103P463040
103P411010
103P462030
103P711030
103P710010
103P711030
103P713030
103C194020
103P331030
103P714090
103P411000
101P221030
101P221030
103P467010
103P467010
103P711030
103P712060
103P711030
103P713090
103P464020
103P713000
103P411010
103P462050
103P711030
103P710010
103P711030
103P713030
103C194020
103P331030
103P714090
103P411000
101P221030
101P221030
Part Name & Description
R-METAL - 1/4W 2.4K-F
R-CARBON - 1/4W 2.7K-J
R-CARBON - 1/4W 68-J
R-METAL - 1/4W 1K-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 10-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 4.7K-J
R-METAL - 3W 27K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 100K-J
R-CARBON - 1/4W 56-J
R-COMP - 1/2W 220-K
R-CARBON - 1/4W 5.6K-J
R-CARBON - 1/4W 6.8K-J
R-COMP - 1/2W 220-K
R-METAL - 1/4W 100K-F
R-METAL - 1/4W 100K-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 4.7K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 6.8K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 1.2K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 15K-J
R-METAL - 1/4W 2.4K-F
R-METAL - 1/4W 2.4K-F
R-CARBON - 1/4W 68-J
R-METAL - 1/4W 820-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 10-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 4.7K-J
R-METAL - 3W 27K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 100K-J
R-CARBON - 1/4W 56-J
R-COMP - 1/2W 220-K
R-COMP - 1/2W 220-K
R-METAL - 1/4W 82K-F
R-METAL - 1/4W 82K-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 1.2K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 15K-J
R-METAL - 1/4W 2.4K-F
R-CARBON - 1/4W 2.7K-J
R-CARBON - 1/4W 68-J
R-METAL - 1/4W 1K-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 10-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 4.7K-J
R-METAL - 3W 27K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 100K-J
R-CARBON - 1/4W 56-J
R-COMP - 1/2W 220-K
R-COMP - 1/2W 220-K
[#]
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
R6R21
R6R22
R6R23
R6R31
R7K01
R7K02
R7K03
R7K21
R7K22
R7K23
R7K24
R7K25
R7K26
R7K27
R7K28
R7K29
R7K30
R7K31
R7K32
R7K33
R7K34
R7K35
R7K36
R7L42
R7L44
R7L45
R7L46
R7L47
R7L48
R7L49
R7P22
R7P28
R8798
R8C05
R8C06
R8C07
R8C13
R8C14
R8C15
R8C21
R8C22
R8C23
R8C29
R8C30
R8C31
R8C37
R8C38
R8C39
R8C45
R8C46
R8C47
R8C60
R8C61
R9A02
R9A03
R9A05
R9A06
R9A09
R9A11
R9A20
Part #
103P467030
103P467030
103P711030
103P712060
103P712050
103P713010
103P719050
103P710090
103P715030
103P712050
103P713080
103P712050
103P715030
103P713070
103P711050
103P712060
103P712050
103P715030
103P713030
103P712050
103P713000
103P711030
103P710090
103P466070
103P462090
103P463030
103P463070
103P464030
103P465010
103P466010
109D151010
109D151010
103C288040
103C288070
103C288070
103C391050
103C288070
103C288070
103C391050
103C288070
103C288070
103C391050
103C288070
103C288070
103C391050
103C288070
103C288070
103C391050
103C288070
103C288070
103C391050
103C191090
103C191090
109P179010
109C010010
109C010010
109C010010
103P145030
103P145030
103P144020
Part Name & Description
R-METAL - 1/4W 100K-F
R-METAL - 1/4W 100K-F
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 1.2K-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 3.3K-J
R-CARBON - 1/4W 0OHM (MAX 3A)
R-CARBON - 1/4W 47-J
R-CARBON - 1/4W 220K-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 12K-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 220K-J
R-CARBON - 1/4W 10K-J
R-CARBON - 1/4W 150-J
R-CARBON - 1/4W 1.2K-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 220K-J
R-CARBON - 1/4W 4.7K-J
R-CARBON - 1/4W 1K-J
R-CARBON - 1/4W 2.7K-J
R-CARBON - 1/4W 100-J
R-CARBON - 1/4W 47-J
R-METAL - 1/4W 56K-F
R-METAL - 1/4W 1.5K-F
R-METAL - 1/4W 2.2K-F
R-METAL - 1/4W 3.3K-F
R-METAL - 1/4W 5.6K-F
R-METAL - 1/4W 12K-F
R-METAL - 1/4W 33K-F
R-CARBON - 1/4W 2.2-J
R-CARBON - 1/4W 2.2-J
R-METAL-CP - 2W 2.2-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-METAL-CP - 2W 3.9-J
R-METAL-CP - 2W 3.9-J
R-METAL-P - 3W 150-J
R-METAL - 3W 330-J
R-METAL - 3W 330-J
R-CEMENT-PLATE - 6.8-J
R-COMP - 1/2W 1M-K
R-COMP - 1/2W 1M-K
R-COMP - 1/2W 1M-K
R-CARBON - 1/2W 220K-J
R-CARBON - 1/2W 220K-J
R-CARBON - 1/2W 27K-J
[#]
Ref #
Part #
Part Name & Description
R9A21
R9A22
R9A25
R9A26
R9A27
R9A36
R9A38
R9A50
R9A52
R9A54
R9A55
R9A59
R9A60
R9A64
R9A67
R9A68
R9A70
R9A71
R9C01
R9D00
103P144020
109P175030
103P142050
109D151090
109D151050
103P142070
103P144090
103P143010
103P140090
109P175020
109P175010
109D151030
109D151090
103P713030
103P710050
103C390020
109D151090
103P145030
103C298040
109D036020
R-CARBON - 1/2W 27K-J
R-WIRE - 2W 0.39-J
R-CARBON - 1/2W 1K-J
R-CARBON - 1/4W 33-J
R-CARBON - 1/4W 75-J
R-CARBON - 1/2W 1.5K-J
R-CARBON - 1/2W 100K-J
R-CARBON - 1/2W 3.3K-J
R-CARBON - 1/2W 47-J
R-WIRE - 2W 0.15-J
R-WIRE - 2W 0.12-J
R-CARBON - 1/4W 4.7-J
R-CARBON - 1/4W 33-J
R-CARBON - 1/4W 4.7K-J
R-CARBON - 1/4W 22-J
R-METAL-P - 3W 12-J
R-CARBON - 1/4W 33-J
R-CARBON - 1/2W 220K-J
R-METAL-CP - 3W 2.2-J
R-COMP - 1/2W 4.7M-K
[#]
CAPACITORS AND TRIMMERS
Chip Type Capacitors (listed by value)
Part No.
Value
Part No.
Value
154P340040
50V 3P-C
141P142010
B50V 0.01M-K
154P340090
CH50V 8P-C
141P143080
F50V 0.01M-Z
154P341010
CH50V 10P-C 141P142090
B25V 0.047M-K
154P341030
CH50V 12P-J
141P143010
B25V 0.068M-K
154P343070
CH50V 120P-J 141P143020
B16V 0.082M-K
154P341050
CH50V 15P-J
141P143030
B16V 0.1M-K
154P341070
CH50V 18P-J
141P144020
F25V 0.1M-Z
154P341090
CH50V 22P-J
141P139030
B25V 0.1M-K
154P342010
CH50V 27P-J
141P134090
F50V 0.1M-Z
154P342030
CH50V 33P-J
141P135080
F50V/25V 0.1M-Z
154P342070
CH50V 47P-J
141P139050
B25V/16V 0.15 M-K
154P340080
CH50V 47P-J
141P138080
B25V 0.33M-K
154P342070
CH50V 47P-J
141P146080
B10V 0.47M-K
154P352080
SL50V 47P-J
141P139090
B16V 0.47M-K
154P342090
CH50V 56P-J
141P134070
B16V 1M-K
154P343030
CH50V 82P-J
141P147020
B10V/6.3V 1M-K
154P343050
CH50V 100P-J 181P526010
50V 1M-M
154P343090
CH50V 150P-J 141P144060
F25V 1M-Z
154P344030
CH50V 220P-J 181P506030
50V 3.3M-M
141P140010
B50V 220P-K
181P524090
35V 4.7M-M 105C
154P344050
CH50V 270P-J 181P502030
16V 10M-M
154P345010
CH50V 470P-J 181P522030
16V 10M-M 105C
141P140050
B50V 470P-K
181P525000
35V 10M-M 105C
154P345030
CH25V 560P-J 181P532030
BP16V 10M-M 105C
154P345050
CH25V 680P-J 181P522040
16V 22M-M 105C
154P345070
CH25V 820P-J 181P520010
6.3V 22M-M 105C
141P143050
F50V 1000P-Z/ 181P520030
6.3V 47M-M
141P140090
B50V 1000P-K 181P500030
6.3V 47M-M
154P345090
CH25V 1000P-J 181P522060
6V 47M-M
141P141010
B50V 1500P-K 181P502070
16V 100M-M
141P141050
B50V 3300P-K 181P528000
4V 100M-M 105C
141P141070
B50V 4700P-K 181P520040
6.3V 100M-M
141P141090
B50V 6800P-K 181P528010
4V 220M-M 105C
141P142000
B50V 8200P-K 181P520050
6.3V 220M-M 105C
PAGE 49
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
C1H03
C1H05
C1H53
C1H55
C2014
C2016
C2019
C2051
C2054
C2064
C2081
C2114
C2144
C2173
C2213
C2233
C2242
C2762
C2803
C2824
C2K06
C2K10
C2K52
C2K59
C2K62
C2K68
C2K72
C2K73
C2K77
C2L01
C2L08
C2L12
C2L13
C2L31
C2L32
C2L33
C2L34
C2L51
C2L52
C2L53
C2L54
C2L61
C2L67
C2L69
C2L70
C2L72
C2L73
C2M26
C2M28
C2M29
C2M31
C2M33
C2M36
C2M38
C2M39
C2M43
C2M44
C2M54
C2M56
Part #
Part Name & Description
Conventional
181P352040
172P262010
181P352040
172P262010
181P355060
181P352040
181P351070
181P352040
181P743040
181P355060
181P355050
181P355060
181P355060
181P355060
181P355060
181P355050
181P355050
181P355050
181P355050
181P355060
181P355050
181P355050
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352010
181P352010
181P352040
181P355050
181P122070
181P355050
181P122070
181P355050
181P122070
181P355050
181P122070
181P352030
181P352010
181P352040
181P352010
181P352040
181P352010
181P352040
181P351080
181P351080
181P352030
181P352030
181P352040
181P352030
181P352030
181P352030
181P352030
181P355050
181P355050
Capacitors (By Ref #)
C-ELEC - 16V 100M-M
C-M-POLY - 50V 0.047M-J
C-ELEC - 16V 100M-M
C-M-POLY - 50V 0.047M-J
C-ELEC - 50V 22M-M
C-ELEC - 16V 100M-M
C-ELEC - 10V 470M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 330M-M
C-ELEC - 50V 22M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 22M-M
C-ELEC - 50V 22M-M
C-ELEC - 50V 22M-M
C-ELEC - 50V 22M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 22M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 22M-M
C-ELEC - 16V 22M-M
C-ELEC - 16V 100M-M
C-ELEC - 50V 10M-M
C-ELEC-NP - 25V 10M-M
C-ELEC - 50V 10M-M
C-ELEC-NP - 25V 10M-M
C-ELEC - 50V 10M-M
C-ELEC-NP - 25V 10M-M
C-ELEC - 50V 10M-M
C-ELEC-NP - 25V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 22M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 22M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 22M-M
C-ELEC - 16V 100M-M
C-ELEC - 10V 1000M-M
C-ELEC - 10V 1000M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
[#]
Ref #
Part #
Part Name & Description
C2M59
C2M64
C2M73
C2M75
C2M77
C2M80
C2M88
C2M89
C2M98
C2N01
C2N04
C2N24
C2N33
C2N41
C2N45
C2N47
C2N48
C2N50
C2N52
C2N60
C2P01
C2P04
C2P24
C2P33
C2P42
C2P45
C2P47
C2P48
C2P50
C2P52
C2P60
C2V14
C2V17
C2V19
C2V29
C2V30
C2V32
C2V48
C2V49
C2V55
C2V57
C2V61
C2V62
C2W02
C2W05
C2W09
C2W14
C3007
C3012
C3022
C3025
C3026
C3061
C3070
C3E01
C3E02
C3E03
C3E04
C3E05
C3E06
181P352030
181P352030
181P355050
181P212060
181P352040
181P352030
181P355010
181P352030
181P355050
181P355040
181P352030
181P352030
181P355040
181P121070
181P121070
181P121070
181P121070
181P121070
181P121070
181P352030
181P355040
181P352030
181P352030
181P355040
181P121070
181P121070
181P121070
181P121070
181P121070
181P121070
181P352030
181P352040
181P355040
181P352040
181P352040
181P118010
181P355000
172P166030
172P166030
181P352040
181P355060
181P352040
181P355050
181P352080
181P352030
181P352030
181P352030
181P353020
181P352030
181P353020
181P352030
181P355030
181P352030
181P352030
181P354050
181P355010
172P331010
181P355010
172P331010
181P355050
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 1M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 4.7M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 4.7M-M
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M
C-ELEC - 50V 4.7M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 4.7M-M
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M NP
C-ELEC - 16V 47M-M
C-ELEC - 16V 100M-M
C-ELEC - 50V 4.7M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 100M-M
C-ELEC - 50V 0.68M-M
C-ELEC - 50V 0.47M-M
C-TF - 50V 0.1M-J
C-TF - 50V 0.1M-J
C-ELEC - 16V 100M-M
C-ELEC - 50V 22M-M
C-ELEC - 16V 100M-M
C-ELEC - 50V 10M-M
C-ELEC - 16V 1000M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 25V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 25V 10M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 3.3M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 35V 47M-M
C-ELEC - 50V 1M-M
C-POLY - 50V 6800P-J
C-ELEC - 50V 1M-M
C-POLY - 50V 6800P-J
C-ELEC - 50V 10M-M
PAGE 50
[#]
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
C3E07
C3E09
C3E11
C3E12
C3E14
C3J08
C3J26
C3J38
C4B01
C4B02
C4B03
C4B04
C4B06
C4B07
C4B08
C4B09
C4B10
C4B11
C5A01
C5A02
C5A03
C5A04
C5A07
C5A09
C5A10
C5A12
C5A14
C5A15
C5A22
C5A23
C5A31
C5A32
C5A34
C5A36
C5A39
C5A40
C5A41
C5A42
C5A43
C5A52
C5A53
C5A55
C5A56
C5A60
C5A61
C5A64
C5A65
C5A68
C5A70
C5A71
C5A72
C5H01
C5H16
C5H17
C5H19
C5H20
C5H21
C5H24
C5K00
C5K01
Part #
181P353090
172P262050
172P262050
172P262050
172P262050
181P352030
181P352030
181P355050
172P261030
181P358000
172P383030
181P184020
172P330090
172P383030
172P263070
181P355060
181P354050
181P353090
181P355050
154P345090
141P140090
172P262010
181P354050
181P355060
172P331070
181P354090
172P434010
189D185010
181P355050
181P355050
172P571070
172P571010
172P434010
172P436070
142P010050
142P011000
181P352080
181P354050
181P780030
172P571030
185D120020
172P082090
181P354050
172P262050
181P355040
181P355060
181P355050
181P123070
172P264010
172P262050
181P355010
181P354080
172P186030
172P261030
181P352040
181P352040
181P780060
181P192060
172P572090
172P572090
Part Name & Description
C-ELEC - 5V 2200M-M
C-M-POLY - 50V 0.1M-J
C-M-POLY - 50V 0.1M-J
C-M-POLY - 50V 0.1M-J
C-M-POLY - 50V 0.1M-J
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-M-POLY - 50V 0.01M-J
C-ELEC - 35V 1000M-M
C-M-POLY - 100V 0.47M-K
C-ELEC - 35V 100M-M
C-POLY - 50V 4700P-J
C-M-POLY - 100V 0.47M-K
C-M-POLY - 50V 1.0M-J
C-ELEC - 50V 22M-M
C-ELEC - 35V 47M-M
C-ELEC - 5V 2200M-M
C-ELEC - 50V 10M-M
C-CER-CHIP - CH25V 1000P-J
C-CER-CHIP - B50V 1000P-K
C-M-POLY - 50V 0.047M-J
C-ELEC - 35V 47M-M
C-ELEC - 50V 22M-M
C-POLY - 50V 0.022M-J
C-ELEC - 35V 470M-M
C-M-PLA-PP - 250V 0.047M-J
C-ELEC - 160V 100M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-M-PLA-PP - 1500V 5600P-J
C-M-PLA-PP - 1500V 2700P-J
C-M-PLA-PP - 250V 0.047M-J
C-M-PLA-PP - 250V 0.56M-J
C-CER - B500V 220P-K
C-CER - B500V 560P-K
C-ELEC - 16V 1000M-M
C-ELEC - 35V 47M-M
C-ELEC - 160V 2.2M-M 105C
C-M-PLA-PP - 1500V 3300P-J
C-ELEC - H160V 470M-M 105C
C-PLA-PP - 630V 8200P-J
C-ELEC - 35V 47M-M
C-M-POLY - 50V 0.1M-J
C-ELEC - 50V 4.7M-M
C-ELEC - 50V 22M-M
C-ELEC - 50V 10M-M
C-ELEC-NP - 50V 0.47M-M
C-M-POLY - 50V 2.2M-J
C-M-POLY - 50V 0.1M-J
C-ELEC - 50V 1M-M
C-ELEC - 35V 330M-M
C-PLA-PP - 200V 0.01M-K
C-M-POLY - 50V 0.01M-J
C-ELEC - 16V 100M-M
C-ELEC - 16V 100M-M
C-ELEC - 160V 10M-M
C-ELEC - 200V 22M-M/Q
C-M-PLA-PP - 1500V 0.015M-J
C-M-PLA-PP - 1500V 0.015M-J
[#]
Ref #
C5K03
C5K04
C5K05
C5K06
C5K07
C5K08
C5K09
C5K10
C5K11
C5K12
C5K13
C5K51
C6B02
C6B03
C6B04
C6B05
C6B06
C6B07
C6B08
C6B09
C6B10
C6B11
C6B12
C6B13
C6B14
C6B20
C6G02
C6G03
C6G04
C6G05
C6G06
C6G07
C6G09
C6G10
C6G11
C6G12
C6G13
C6G14
C6G20
C6R02
C6R03
C6R04
C6R05
C6R06
C6R07
C6R09
C6R10
C6R11
C6R12
C6R13
C6R14
C6R20
C7A00
C7B02
C7B16
C7B88
C7B96
C7B99
C7DF3
C7K01
PAGE 51
Part #
142P024060
181P191000
172P383030
154P260080
172P261030
155P239040
172P262010
181P354050
181P355050
172P262010
154P270050
142P023080
181P195050
155P231070
142P023080
181P352080
142P023080
172P532050
142P020030
142P023080
172P532050
154P400010
155P231050
155P231090
154P405000
172P532050
181P195050
155P232010
142P023080
181P352080
142P023080
172P532050
142P023080
172P532050
154P400010
155P231050
155P231090
154P405000
172P532050
181P195050
155P231090
142P023080
181P352080
142P023080
172P532050
142P023080
172P532050
154P400010
155P231050
155P231090
154P405000
172P532050
154P345050
181P355020
181P352030
181P355050
181P355020
181P352030
181P350060
181P352030
Part Name & Description
C-CER - BF50V 0.1M-Z
C-ELEC - 160V 22M-M/Q
C-M-POLY - 100V 0.47M-K
C-CER - R1KV 3300P-K
C-M-POLY - 50V 0.01M-J
C-CER - CH50V 100P-J
C-M-POLY - 50V 0.047M-J
C-ELEC - 35V 47M-M
C-ELEC - 50V 10M-M
C-M-POLY - 50V 0.047M-J
C-CER - SL1KV 22P-J
C-CER - BF50V 0.01M-Z
C-ELEC - 350V 10M-M/Q
C-CER - CH50V 18P-J
C-CER - BF50V 0.01M-Z
C-ELEC - 16V 1000M-M
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - B50V 330P-K
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - B1KV 220P-K
C-CER - CH50V 15P-J
C-CER - CH50V 22P-J
C-CER - B3KV 1000P-K
C-M-POLY - 400V 0.1M-J
C-ELEC - 350V 10M-M/Q
C-CER - CH50V 27P-J
C-CER - BF50V 0.01M-Z
C-ELEC - 16V 1000M-M
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - B1KV 220P-K
C-CER - CH50V 15P-J
C-CER - CH50V 22P-J
C-CER - B3KV 1000P-K
C-M-POLY - 400V 0.1M-J
C-ELEC - 350V 10M-M/Q
C-CER - CH50V 22P-J
C-CER - BF50V 0.01M-Z
C-ELEC - 16V 1000M-M
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - BF50V 0.01M-Z
C-M-POLY - 400V 0.1M-J
C-CER - B1KV 220P-K
C-CER - CH50V 15P-J
C-CER - CH50V 22P-J
C-CER - B3KV 1000P-K
C-M-POLY - 400V 0.1M-J
C-CER-CHIP - CH25V 680P-J
C-ELEC - 50V 2.2M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 2.2M-M
C-ELEC - 16V 47M-M
C-ELEC - 3V 1000M-M
C-ELEC - 16V 47M-M
[#]
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
C7K20
C7K21
C7K23
C7K25
C7K26
C7K27
C7K28
C7K30
C7M92
C7N06
C7P15
C7P19
C7P22
C7Q02
C7Q03
C7Q52
C7Q53
C7R08
C81A2
C81A3
C81B3
C81B4
C8281
C8705
C8710
C8717
C8719
C8720
C8725
C8727
C8729
C8730
C8733
C8751
C8761
C8764
C8771
C8772
C8780
C8783
C8795
C8797
C8798
C8889
C8C03
C8C05
C8C18
C8C20
C8D12
C8D16
C8D20
C8D21
C8D22
C8D30
C8D31
C8D39
C8D40
C8E01
C8E03
Part #
155P314040
181P355050
181P355010
172P262050
172P262050
181P355010
181P352040
172P261030
181P350040
181P350040
181P212060
181P352030
181P352050
181P352040
181P352030
181P352040
181P352030
181P355050
181P182030
181P182030
181P182030
181P182030
189P197020
181P185060
181P181000
181P352060
181P732000
181P185060
181P182010
181P181000
181P732000
181P352060
181P182010
181P355090
181P352060
181P352060
181P353060
181P732000
181P352060
181P350040
181P350040
181P350040
181P350040
181P350040
181P358000
181P358000
181P358000
181P358000
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
Part Name & Description
[#]
C-CER - SL50V 220P-J
C-ELEC - 50V 10M-M
C-ELEC - 50V 1M-M
C-M-POLY - 50V 0.1M-J
C-M-POLY - 50V 0.1M-J
C-ELEC - 50V 1M-M
C-ELEC - 16V 100M-M
C-M-POLY - 50V 0.01M-J
C-ELEC - 6.3V 330M-M
C-ELEC - 6.3V 330M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 220M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 47M-M
C-ELEC - 50V 10M-M
C-ELEC - 16V 1000M-M 105C
C-ELEC - 16V 1000M-M 105C
C-ELEC - 16V 1000M-M 105C
C-ELEC - 16V 1000M-M 105C
C-ELE-DBL-LA - FM0H473Z/EECS5R5T473Z
C-ELEC - 50V 10M-M 105C
C-ELEC - 10V 330M-M 105C
C-ELEC - 16V 330M-M
C-ELEC - 10V 680M-M 105C
C-ELEC - 50V 10M-M 105C
C-ELEC - 16V 330M-M 105C
C-ELEC - 10V 330M-M 105C
C-ELEC - 10V 680M-M 105C
C-ELEC - 16V 330M-M
C-ELEC - 16V 330M-M 105C
C-ELEC - 50V 100M-M
C-ELEC - 16V 330M-M
C-ELEC - 16V 330M-M
C-ELEC - 25V 330M-M
C-ELEC - 10V 680M-M 105C
C-ELEC - 16V 330M-M
C-ELEC - 6.3V 330M-M
C-ELEC - 6.3V 330M-M
C-ELEC - 6.3V 330M-M
C-ELEC - 6.3V 330M-M
C-ELEC - 6.3V 330M-M
C-ELEC - 35V 1000M-M
C-ELEC - 35V 1000M-M
C-ELEC - 35V 1000M-M
C-ELEC - 35V 1000M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
Ref #
C8E05
C8E07
C8E09
C8E12
C8E14
C8E16
C8G00
C8G01
C8G03
C8G05
C8G06
C9A01
C9A05
C9A06
C9A08
C9A09
C9A10
C9A11
C9A13
C9A14
C9A20
C9A21
C9A25
C9A26
C9A29
C9A30
C9A32
C9A33
C9A34
C9A35
C9A37
C9A38
C9A41
C9A43
C9A45
C9A50
C9A51
C9A52
C9A54
C9A56
C9A57
C9A58
C9A59
C9A60
C9A61
C9A62
C9A63
C9A65
C9A66
C9A68
C9A69
C9A72
C9A74
C9A75
C9A79
C9A80
C9A85
C9A86
C9C02
C9C03
PAGE 52
Part #
Part Name & Description
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352030
181P352020
181P352030
181P352030
181P352030
189P185070
189P185070
189P185090
189P185090
189P185090
189P185090
189P152070
189P152070
154P400050
181P355050
172P138010
185D122050
181P355050
181P355050
181P735020
181P735020
154P400050
181P735010
181P734000
181P734000
181P732010
172P262050
189P185090
142P020050
181P355090
154P260080
154P260080
181P355080
142P010090
185D122040
185D122040
154P400030
142P010090
189D183010
185D120020
181P194000
142P012050
142P010090
181P736070
181P736070
142P010090
181P355080
181P736070
181P736070
181P735020
181P735020
181P352040
181P743040
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 33M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-CER - AC250V E1000P-M
C-CER - AC250V E1000P-M
C-CER - AC250V E2200P-M
C-CER - AC250V E2200P-M
C-CER - AC250V E2200P-M
C-CER - AC250V E2200P-M
C-M-POLY - 250VAC 0.01M-M
C-M-POLY - 250VAC 0.01M-M
C-CER - B1KV 1000P-K
C-ELEC - 50V 10M-M
C-POLY - 50V 4700P-J
C-ELEC - H200V 1000M-M
C-ELEC - 50V 10M-M
C-ELEC - 50V 10M-M
C-ELEC - 25V 1000M-M 105C
C-ELEC - 25V 1000M-M 105C
C-CER - B1KV 1000P-K
C-ELEC - 25V 470M-M
C-ELEC - 16V 2200M-M 105C
C-ELEC - 16V 2200M-M 105C
C-ELEC - 10V 1000M-M 105C
C-M-POLY - 50V 0.1M-J
C-CER - AC250V E2200P-M
C-CER - B50V 470P-K
C-ELEC - 50V 100M-M
C-CER - R1KV 3300P-K
C-CER - R1KV 3300P-K
C-ELEC - 50V 47M-M
C-CER - B500V 470P-K
C-ELEC - H200V 820M-M
C-ELEC - H200V 820M-M
C-CER - B1KV 470P-K
C-CER - B500V 470P-K
C-ELEC - 400V 100M-KC
C-ELEC - H160V 470M-M 105C
C-ELEC - 250V 10M-M/Q
C-CER - B500V 0.01M-K
C-CER - B500V 470P-K
C-ELEC - 35V 330M-M
C-ELEC - 35V 330M-M
C-CER - B500V 470P-K
C-ELEC - 50V 47M-M
C-ELEC - 35V 330M-M
C-ELEC - 35V 330M-M
C-ELEC - 25V 1000M-M 105C
C-ELEC - 25V 1000M-M 105C
C-ELEC - 16V 100M-M
C-ELEC - 16V 330M-M
[#]
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
Part #
Part Name & Description
C9C06
C9C07
C9C10
C9C13
C9C14
C9C16
C9C19
C9C22
C9C42
C9C44
C9C62
C9D00
C9D02
C9M01
C9M04
C9M05
C9M08
181P352040
181P743040
181P743040
181P352040
181P743040
181P352040
181P743040
181P352030
181P352040
181P352040
181P352030
189P153040
189P153040
181P352030
181P352030
181P212060
181P352030
S7L40
S7L41
S7L42
S7L43
S7L44
S7L45
S7L46
S7L47
S7L48
S7L49
432P109010
432P109010
432P109010
432P109010
432P109010
432P109010
432P109010
432P109010
432P109010
432P109010
[#]
Ref #
C-ELEC - 16V 100M-M
C-ELEC - 16V 330M-M
C-ELEC - 16V 330M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 330M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 330M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 100M-M
C-ELEC - 16V 47M-M
C-M-POLY - 250VAC 0.1M-M
C-M-POLY - 250VAC 0.1M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
C-ELEC - 16V 47M-M
SWITCHES
SW-KEY BOARD - KSHS611BT
SW-KEY BOARD - KSHS611BT
SW-KEY BOARD - KSHS611BT
SW-KEY BOARD - KSHS611BT
SW-KEY BOARD - KSHS611BT
SW-KEY BOARD - KSHS611BT
SW-KEY BOARD - KSHS611BT
SW-KEY BOARD - KSHS611BT
SW-KEY BOARD - KSHS611BT
SW-KEY BOARD - KSHS611BT
MISCELLANEOUS
096Z465030
242D535040
242D535050
242D540010
242D540020
242D540030
246C351030
299P103060
299P254020
305P703010
330P294020
338P054010
338P054020
411D033010
411D044020
411D062010
411D064010
411D064020
452C411010
453B036010
453B036020
453B036070
453B036080
480P063010
598D417020
622D875010
642C340010
TAPE-LENS
CABLE - 1394 - 300mm
CABLE - 1394 - 1000mm
CABLE-IF - F-CONN 250mm
CABLE-IF - PIN-PLUG 325mm
CABLE-IF - PIN-PLUG 375mm
CORD-AC - POWER
FAN - MMF-04B12-DL-RB1
IR-EMITTER, 4-HEAD - T-IR-02 W
/FERRITE CO
2RF-SWITCH
YOKE-DEFL - 720UH
SVM-ASSY
SVM-ASSY
CORE-FERRITE - R15 L18
CORE-FERRITE - ZCAT2032-0930
CORE-FERRITE - ZCAT1518-0730
FERRITE CORE - HF57SH35X0.8
FERRITE CORE - HF57SH28X0.7
CONNECTOR: PC-CARD
CAP-ANODE - [R]
CAP-ANODE - [GB]
CAP-ANODE - [R]
CAP-ANODE - [BG]
SPEAKER - 6"
PLATE - RF-SWITCH
CUSHION-TAPE - OPTICAL
BRACKET-MIRROR - TOP
b
ab
c
c
ab
ab
c
c
c
b
Part #
642C352010
702A447010
767C031020
767D048090
767D072030
AG6B01 224D019090
AG6B02 224D019090
AG6G01 224D019090
AG6G02 224D019090
AG6R01 224D019090
AG6R02 224D019090
F5A00 283P144070
F9A01 283P144060
F9A02 283P144090
F9A03 283P144080
F9A04 283P144080
F9A05 283P144080
F9A21 283P144090
F9A22 283P144090
F9A23 283P144070
F9D00 283D131040
SF8800 296P171010
SF8801 296P172010
CF2N01 299P128010
CF2P01 299P128010
CF2V01 299P259010
SKT6B1 449C141030
SKT6R1 449C141030
STK6G1 449C141030
J2000
452C410010
J2J21
452C401010
J2J22
451P246010
J8202
452C401010
J8301
440C393030
J8402
451P246010
J8403
451P246010
K9A50 287P111030
PC9A21 268P058020
PC9A50 268P106010
PJ2J00 440C407010
PJ2J01 440C412020
PJ2J02 440C421010
PJ2J03 440C410010
PJ2J04 440C410010
PJ2J05 440C421010
PJ2J06 451C259010
PJ2J07 451C259010
PJ2J11 440C412010
TU8700 295P490040
TU8701 295P523010
TU8702 295P524010
TU8704 295P527020
X2K51 285P426020
X2M47 285P426040
X2N26 285P426010
X2P26 285P426010
X3001 285P413010
X7A13 285P434020
X7J10 285P335050
X7P09 285P434010
PAGE 53
Part Name & Description
[#]
CLIP-MIRROR - TOP
a
PANEL-TERMINAL
MIRROR - 73"
c
MIRROR - 65"
b
MIRROR - 55"
a
AIR GAP - 1.5+-0.5KV
AIR GAP - 1.5+-0.5KV
AIR GAP - 1.5+-0.5KV
AIR GAP - 1.5+-0.5KV
AIR GAP - 1.5+-0.5KV
AIR GAP - 1.5+-0.5KV
FUSE - 125V 3A
FUSE - 125V 7A
FUSE - 125V 10A
FUSE - 125V 5A
FUSE - 125V 5A
FUSE - 125V 5A
FUSE - 125V 10A
FUSE - 125V 10A
FUSE - 125V 3A
FUSE - S10A 125A
SAW-FILTER - X6892D
SAW-FILTER - X7303P
OSC-CERAMIC - CSB500F2
OSC-CERAMIC - CSB500F2
OSC-CERAMIC - CSALA2M6964ZF01-B0
SOCKET-CRT
SOCKET-CRT
SOCKET-CRT
CONNECTOR-HDMI
CONNECTOR-USB
JACK-1394 - MINI
CONNECTOR-USB
PIN-JACK-BOARD-1P
JACK-1394 - MINI
JACK-1394 - MINI
RELAY-POWER - LKS1AF-12V
PHOTO-COUPLER - ON3131-R/ON3161-R
PHOTO-COUPLER - CNZ3133
PIN-JACK-BOARD-6P
PIN-JACK-BOARD-3P-1S
PIN-JACK-BOARD-2P
PIN-JACK-BOARD-5P
PIN-JACK-BOARD-5P
PIN-JACK-BOARD-2P
JACK-MICROPHONE
JACK-MICROPHONE
PIN-JACK-BOARD-3P
TUNER-TV - ENA46914P4A
TUNER-NTSC/ATSC
TUNER-OOB
NTSC DEMODULATOR
QTZ-CRYST - 4.000000MHZ
QTZ-CRYST - 20.000MHZ
QTZ-CRYST - 3.579545MHZ
QTZ-CRYST - 3.579545MHZ
QTZ-CRYST - 18.432MHZ
QTZ-CRYST - 16.000MHZ
QTZ-CRYST - 80.000MHZ
QTZ-CRYST - 8.000MHZ
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend:
(a) WS-55517, (b) WS-65517, (c) WS-73517
Ref #
X8001
X8301
X8303
X8401
X8402
X8800
Z7K01
Z81A1
Z81A2
Z81A3
Z81A4
Part #
Part Name & Description
285P441040
285P434020
285P413010
285P431020
285P410020
285P453010
938P005010
283P128050
283P128050
283P128050
283P128050
QTZ-CRYST - 26.1621MHZ
QTZ-CRYST - 16.000MHZ
QTZ-CRYST - 18.432MHZ
QTZ-CRYST - 54.000MHZ
QTZ-CRYST - 24.576MHZ
QTZ-CRYST - 25.140MHZ
UNIT-PREAMP
FUSE-CHIP - AC125/100V
FUSE-CHIP - AC125/100V
FUSE-CHIP - AC125/100V
FUSE-CHIP - AC125/100V
[#]
Ref #
4A
4A
4A
4A
PRINTED CIRCUIT BOARDS
930B918002 ASSY-PWB-MAIN
930B918003 ASSY-PWB-MAIN
930B919002-55 ASSY-PWB-SIGNAL
930B919002-65 ASSY-PWB-SIGNAL
930B919003 ASSY-PWB-SIGNAL
930B920001 ASSY-PWB-TERMINAL
934C106001 ASSY-PWB-CRT
934C107001 ASSY-PWB-HDMI
934C108003 ASSY-PWB-DM3
934C109001-55 ASSY-PWB-E2P
934C109001-65 ASSY-PWB-E2P
934C109001-73 ASSY-PWB-E2P
934C110005 ASSY-PWB-DTV-TUNER
935D762001 ASSY-PWB-PREAMP
935D763001 ASSY-PWB-FRONT
935D767001 ASSY-PWB-DBF
935D770001 ASSY-PWB-FIF
935D772001 ASSY-PWB-CONTROL
ab
c
a
b
c
a
b
c
COSMETIC PARTS
761A224020
761A225020
761A226020
850A004010
850C089010
GRILLE SPEAKER
GRILLE SPEAKER
GRILLE SPEAKER
INLAY-TERMINAL
INLAY-DM
a
b
c
ACCESSORIES
242D525010
290P122010
I/QR WS55517
I/B WS55517
CABLE - AUDIO - AC3
REMOTE-CONTROL - V25/V25+
QR GUIDE
IB PCTV
PAGE 54
Part #
Part Name & Description
[#]
MODELS: WS-55517 / WS-65517 / WS-73517
[#] Model Legend: (a) WS-55517, (b) WS-65517, (c) WS-73517
Ref # Part #
Part Name & Description
[#]
SCREEN ASSEMBLY PARTS
WS-55517 Screen Parts
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
491P181010
491P180010
702A449020
701B498010
598D619010
635B113010
760D628080
622C104030
702A550020
(1)
(2)
(3)
(4)
(5)
491P183010
491P182010
702A453020
701B498020
598D619010
LENS-FRESNEL
SCREEN-LENTICULAR
FRAME SCREEN - TOP
FRAME-SCREEN - SIDE
BRACKET-SCREEN - SIDE
FRAME-TOP - SUPPORT
DIAMOND SHIELD - 55"
HOLDER-SCREEN
CONTROL PANEL
a
a
a
a
a
a
a
a
a
WS-65517 Screen Parts
LENS-FRESNEL
SCREEN-LENTICULAR
FRAME SCREEN - TOP
FRAME-SCREEN - SIDE
BRACKET-SCREEN - SIDE
b
b
b
b
b
Ref # Part #
(6)
(7)
(8)
(9)
(10)
635B113020
760D627070
622C214010
702A452020
594C988010
Part Name & Description
FRAME-TOP - SUPPORT
DIAMOND SHIELD - 65"
HOLDER-SCREEN
CONTROL PANEL
BRACKET-SCREEN - FRAME
[#]
b
b
b
b
b
WS-73517 Screen Parts
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
PAGE 55
491P186010
491P185010
702A454020
701B498030
598D619010
635B113030
760D638010
622C214010
702A450020
594C988010
LENS-FRESNEL
SCREEN-LENTICULAR
FRAME SCREEN - TOP
FRAME-SCREEN - SIDE
BRACKET-SCREEN - SIDE
FRAME-TOP - SUPPORT
DIAMOND SHIELD - 73"
HOLDER SCREEN
CONTROL PANEL
BRACKET-SCREEN - FRAME
c
c
c
c
c
c
c
c
c
c
MODEL: WS-55517 / WS-65517 / WS-73517
POWER SUPPLY
Page 56
MODEL: WS-55517 / WS-65517 / WS-73517
VIDEO SIGNAL PATH
Page 57
A/V SWITCH
MODEL: WS-55517 / WS-65517 / WS-73517
Page 58
MODEL: WS-55517 / WS-65517 / WS-73517
SYNC PATH
Page 59
MODEL: WS-55517 / WS-65517 / WS-73517
DEFLECTION / HV
Page 60
MODEL: WS-55517 / WS-65517 / WS-73517
X-RAY PROTECT
Page 61
CONVERGENCE CIRCUIT
MODEL: WS-55517 / WS-65517 / WS-73517
Page 62
MODEL: WS-55517 / WS-65517 / WS-73517
SOUND CIRCUIT
Page 63
MODEL: WS-55517 / WS-65517 / WS-73517
CONTROL CIRCUITRY
Page 64
Ser vice
Manual
2004/2005
MITSUBISHI ELECTRIC
PROJECTION TELEVISION
V25 / V25+ / V25++ / V27 CHASSIS
WS-48515
V25 MODELS
V25+ MODELS
V25++ MODELS
V27 MODELS
WS-48515
WS-55515
WS-65515
WS-55815
WS-65815
WS-55615
WS-65615
WS-73615
WS-55517
WS-65517
WS-73517
CAUTION:
Before servicing this chassis, it is important that the service person read the "SAFETY PRECAUTIONS" and
"PRODUCT SAFETY NOTICE" contained in Part 1 of this manual.
PART 2
SCHEMATIC DIAGRAMS
CONTENTS
Page
Overall PCB Block Diagram ........................................... 1
PCB-MAIN ..................................................................... 2
PCB-TERMINAL [INPUT SWITCH] ................................ 3
PCB-TERIMINAL [PIC µP / FIF / E2P] ............................ 4
PCBs-CRT / DBF / PREAMP /CONTROL1 /
CONTROL2 / FRONT ......................................... 5
PCB-HDMI ..................................................................... 6
PCB-SIGNAL-1 [MICRO] ............................................... 7
PCB-SIGNAL-2 [CONVERGENCE GENERATOR] ....... 8
PCB-SIGNAL-3 [VCJ / VERTICAL DEF / AUDIO] .......... 9
PCB-TUNER-1 [TUNER / AUDIO] ................................ 10
PCB-TUNER-2 [ATSC DEMOD] .................................. 11
Refer to PART 1 for:
• Specifications
• Safety Precautions
• Disassembly
• CRT Replacement
• Electrical Adjustments
• Parts List
• Block Diagrams
MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC.
9351 Jeronimo Road, Irvine, CA 92618-1904
Copyright © 2005 Mitsubishi Digital Electronics America, Inc.
All Rights Reserved