Casio DT-X7 Series User`s guide

E
Handheld Terminal
Series
User’s Guide
Be sure to read “Safety
Precautions” inside this
guide before trying to use
your Handheld Terminal.
Illustrated operating instructions in this user’s
guide use laser model of DT-X7 series.
• This Product is equipped with the Brycen BL-RAPPORE Stack and My Wirefree
Network Bluetooth User Interface Application, the use of which is governed by a license
granted by Brycen Co., Ltd.
• BLUETOOTH is a registered trademark owned by Bluetooth SIG, Inc. and licensed to
CASIO COMPUTER CO., LTD.
• Microsoft and Windows are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
Information in this document is subject to change without advance notice. CASIO Computer Co.,
Ltd. makes no representations or warranties with respect to the contents or use of this manual
and specifically disclaims any express or implied warranties of merchantability or fitness for any
particular purpose.
Contents
Safety Precautions .........................................................................................E-3
Operating Precautions ...................................................................................E-8
Important ........................................................................................................E-9
Regulatory Information ...............................................................................E-10
Checking in the Box .....................................................................................E-14
Handheld Terminal System Configuration .................................................E-15
General Guide ...............................................................................................E-18
Loading and Removing the Battery Pack...................................................E-21
Loading .............................................................................................................. E-22
Removing ........................................................................................................... E-23
Attaching the Hand Strap ............................................................................E-25
Setting up ......................................................................................................E-26
Using the Mouse Emulator Function ................................................................. E-26
Adjusting Display Brightness ............................................................................ E-28
Display Auto Dimmer ........................................................................................ E-28
Using the Laser Scanner (DT-X7M10E/DT-X7M10R2) ...............................E-29
Attaching the Bumper ........................................................................................ E-29
Warning Label .................................................................................................... E-30
Bar Code Scanning Position .............................................................................. E-30
Adjusting the Laser Light Emission Width .................................................E-31
Using the C-MOS Imager (DT-X7M30E/DT-X7M30R) ................................E-33
Warning Label .................................................................................................... E-34
Using the Linear Imager (DT-X7M10U) .......................................................E-35
Warning Label .................................................................................................... E-35
Performing Communications .....................................................................E-36
IR Communication ............................................................................................. E-36
Bluetooth® Communication ............................................................................... E-37
Resetting the Handheld Terminal ................................................................E-38
Performing a Full Reset (Initialization) ............................................................ E-39
E-1
DT-X7 Specifications ...................................................................................E-40
Using the USB Cradle (HA-F60IO) ...............................................................E-44
General Guide .................................................................................................... E-44
Connecting the USB Cradle Power Supply .......................................................E-46
Specifications .....................................................................................................E-48
Using the Ethernet Cradle (HA-F62IO)........................................................E-49
General Guide .................................................................................................... E-49
Connecting the Ethernet Cradle Power Supply.................................................. E-51
Specifications .....................................................................................................E-53
Using the Cradle-type Battery Charger (HA-F30CHG) ..............................E-54
General Guide .................................................................................................... E-54
Connecting the AC Adaptor for Cradle-type Battery Charger ........................... E-55
Specifications .....................................................................................................E-57
Using the Cradle-type Dual Battery Charger (HA-F36DCHG) ..................E-58
General Guide .................................................................................................... E-58
Charging Battery Pack ....................................................................................... E-60
Connecting Multiple Cradle-type Dual Battery Chargers..................................E-61
Specifications .....................................................................................................E-62
Using the Dual Battery Charger (HA-F32DCHG)........................................E-64
General Guide .................................................................................................... E-64
Charging Battery Pack ....................................................................................... E-66
Connecting Multiple Dual Battery Chargers...................................................... E-67
Specifications .....................................................................................................E-68
Using Rechargeable Battery Pack ..............................................................E-69
Battery Pack Specifications................................................................................E-70
Large-capacity Battery Pack Specifications .......................................................E-70
Attaching the Hand Belt (HA-F95HB) ..........................................................E-71
Attaching the Hand Belt.....................................................................................E-71
E-2
Safety Precautions
Congratulations upon your selection of this CASIO product. Be sure to read the
following Safety Precautions before trying to use it for the first time.
Your neglect or avoidance of the warning and caution statements in the
subsequent pages causes the danger of fire, electric shock, malfunction and
damage on the goods as well as personal injury.
Markings and Symbols
The following are the meanings of the markings and symbols used in these Safety
Precautions.
Danger
This symbol indicates information that, if ignored or applied
incorrectly, creates the danger of death or serious personal injury.
Warning
This symbol indicates information that, if ignored or applied
incorrectly, creates the possibility of death or serious personal
injury.
Caution
This symbol indicates information that, if ignored or applied
incorrectly, creates the possibility of personal injury or property
damage.
• A diagonal line indicates something you should not do. The symbol shown
here indicates you should not try to take the unit apart.
• A black circle indicates something you should do. The symbol shown here
indicates you should unplug the unit from the wall outlet.
Warning
Disassembly and Modification
• Never try to disassemble or modify the Handheld Terminal and its options
including battery pack and battery in any way.
Abnormal Conditions
• Should the Handheld Terminal and/or its options including battery pack and
battery become hot or start to emit smoke or a strange odor, immediately turn
off the power and contact your dealer or distributor whom you purchased the
product from, or an authorized CASIO service provider.
E-3
Warning
Dust and Moisture
• Though the Handheld Terminal is dust and water splash resistant, its options
including the battery pack are not. Keep loose metal objects and containers
filled with liquid away from your Handheld Terminal and the options. Also,
never handle the Handheld Terminal and the options while your hands are wet.
Laser Light
• The products (Laser Scanner and C-MOS Imager models) scan bar codes
using laser light. Never look directly into the laser light or shine the laser
light into the eyes.
LED Light
• This product (DT-X7M10U) scans bar codes using LED light. Never look
directly into the LED light or shine the LED light into the eyes.
Warning
Interference with the Operation of Other Equipment
(Using Wireless Data Communication)
11
• Keep your Handheld Terminal at least 22 centimeters (8 /16") away from
anyone wearing a pacemaker. Radio waves emitted by the Handheld
Terminal can affect the operation of a pacemaker.
• Before the use in aircraft, be sure to consult with cabin crew for interference
the Handheld Terminal emits.
• Before the use in medical facility, be sure to consult with the facility
management or the manufacture of a specific medical equipment that the
Handheld Terminal may interfere with.
• Do not use the Handheld Terminal nearby gas pump or chemical tank or any
other places flammable or explosive.
E-4
Caution
Foreign Objects
• Take care to ensure that metals or combustible objects are not inserted into
the openings of the Handheld Terminal or its options, and not to allow
moisture to get inside of them.
Location
• Install the cradle properly on a flat and stable surface so that it cannot fall
down onto floor.
• Do not leave the Handheld Terminal and its options for a long period in a
car parked in direct sunlight.
LCD Screen
• Never apply strong pressure to the screen or subject it to strong impact.
Doing so can crack the LCD Screen.
E-5
Optional Lithium-ion Battery Pack
Danger
• Never use the Handheld Terminal and its option including the battery pack
and battery next to open flame, near a stove, or any other area exposed to
high heat, or leave them for a long period of time in a vehicle parked in
direct sunlight.
• Never use the battery pack with any device other than the Handheld
Terminal.
• Never dispose of the battery pack by incinerating it or otherwise expose it
to heat.
• Never transport or store the battery pack together with metal objects that
may result in shorting positive (+) and negative (–) terminals of the battery
pack. Be sure to place the battery pack in its case whenever transporting or
storing it.
• Never throw the battery pack or otherwise subject it to strong impact.
• Never pierce the battery pack with nails, hit it with a hammer, or step on it.
• Use only the specified battery charger to charge the battery pack.
Warning
• Never place the battery pack in a microwave oven or any other high-voltage
device.
• If the amount of time period the battery pack can serve becomes
considerably short even after it has been fully charged for the specified time
period, stop using it.
• Should the battery pack start to leak or emit a strange odor, immediately
move it away from any flame nearby. Leaking battery fluid is combustible.
• Should fluid from the battery pack accidentally get into your eyes or on the
skin, do not rub it. Immediately rinse it off with clean tap water and then
consult a physician.
Caution
• Replace only with the same type of battery pack recommended by CASIO.
Dispose of used battery packs according to the local regulation.
• Keep the battery pack out of the reach of small children.
E-6
Power Supply / AC Adaptor
Warning
• Do not use the Handheld Terminal at a voltage other than the specified voltage.
Also, do not connect the Handheld Terminal to a multi-plug power strip.
• Never modify, sharply bend, twist, or pull on the power cord.
• Never use a detergent to clean AC adaptor and its power cable, especially
on the plug and the jack.
• When using the battery chargers and the cradles, be sure to use the respective
AC adaptors.
Caution
• Never pull on the power cord when unplugging it. Always hold the plug
when unplugging it from the wall outlet.
• Never touch the plug while your hands are wet.
• Be sure to unplug the power cord from the wall outlet before cleaning the
battery chargers and the cradles.
• Unplug the power cord from the wall outlet whenever leaving the battery
chargers and the cradles unattended for a long period.
• The housing of the AC adaptor can become warm during normal use.
• At least once a year, unplug the AC adaptor from the wall outlet and clean
any dust that builds up between the prongs of the plug.
Dust built up between the prongs can lead to the danger of fire.
Backup Copies of All Important Data
Caution
• Note that CASIO Computer Co., Ltd. shall not be held liable to you or any
third party for any damages or loss caused by deletion or corruption of data
due to use of the Handheld Terminal, malfunction or repair of the Handheld
Terminal or its peripherals, or due to the batteries going dead.
• The Handheld Terminal employs electronic memory to store data, which
means that memory contents can be corrupted or deleted if power is
interrupted due to the batteries going dead or incorrect battery replacement
procedures. Data cannot be recovered once it is lost or corrupted. Be sure to
make backup copies of all important data. One way to do this is to use the
separately sold cradles to transfer data to a computer.
E-7
Operating Precautions
Your Handheld Terminal and its options are precision. Improper operation or rough
handling can cause problems with data storage and other problems. Note and observe
the following precautions to ensure proper operation.
• Do not continue operating the Handheld Terminal when battery power is low.
Doing so can cause data to be lost. When the battery goes low, charge it as soon as
possible.
• Do not leave dead battery pack in the Handheld Terminal for a long period.
Dead battery pack can leak, leading to malfunction and damage to the Handheld
Terminal.
• Use the Handheld Terminal and its options only within the specified
temperature range.
Use outside of the specified temperature range creates the risk of malfunction.
• Avoid using the Handheld Terminal and its options in areas subject to the
following conditions.
— Large amounts of static electricity
— Extreme heat or extreme cold
— High humidity
— Sudden temperature extremes
— Large amounts of dust
• Never use thinner, benzene, cosmetic cleaning fluids, or other volatile agents to
clean the Handheld Terminal.
To clean the Handheld Terminal, wipe it with a dry cloth, or a cloth moistened in
a weak solution of water and a mild neutral detergent. Wring all excess moisture
from the cloth before wiping.
• Although the Handheld Terminal meets the IP54 level of the International
Standard IEC60529, pay your attention to the following when using it in the
rain.
— After a large amount of rain or water falls on the Handheld Terminal, wipe off it
immediately.
— Do not use it in the rain for a long period of time.
— Make sure the battery cover and connect cover are closed securely before using it.
— Do not press on the screen or keys with excessive force when using it in the rain.
• Dead Pixels
The LCD panel employed in this product uses high precision and substantial number
of components which commonly cause a small number of the pixels not to light or
to remain lit all the time. This is due to the characteristics of LCD panel yield in
accuracy over 99.99% and permissible.
E-8
Important
• This guide does not include any information about programming and download
procedures. See the applicable separate documentation for information about the
procedures.
After Service
• Should this product ever malfunction, contact your original retailer providing
information about the product name, the date you purchased it, and details about the
problem.
This mark applies to EU countries and Turkey only.
E-9
Regulatory Information
The USA and Canada
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not
applicable to other areas).
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Proper connectors must be used for connection to host computer and/or peripherals in order to meet FCC
emission limits.
Caution Exposure to radio frequency radiation (below is for portable device)
To comply with FCC RF exposure compliance requirements, this device must not be co-located or
operating in conjunction with any other antenna or transmitter.
Declaration of Conformity
Model Number:
HA-F60IO, HA-F62IO
Trade Name:
CASIO
Responsible party: Casio America, Inc. Industrial Handheld Division
Address:
10710 Baxter Avenue, Los Altos, California 94024 USA
Telephone number: 585-624-2562
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For Customers in Canada
These Class B digital apparatuses comply with Canadian ICES-003.
Cet appareil numériqué de la classes B est conformé à la norme NMB-003 du Canada.
These devices comply with RSS 210 of Industry Canada (IC).
Operation is subject to the following two conditions:
(1) These devices may not cause interference, and
(2) These devices must accept any interference, including interference that may cause undesired operation of this device.
E-10
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si ce
brouillage est susceptible de compromettre le fonctionnement du dispositif.
Exposure to radio frequency radiation
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does
not emit RF field in excess of Health Canada limits for the general population;
consult Safety Code 6, obtainable from Health Canada's website at www.hc-sc.gc.ca/rpb.
Europe
We, the undersigned.
Company
Address, City
Country
Phone number
Fax number
CASIO Europe GmbH
Casio-Platz 1, 22848 Norderstedt
Germany
+49(0)40-528-65-0
+49(0)40-528-65-424
certify and declare under our sole responsibility that the following equipments:
Product description/Intended use
EU/EFTA member states intended for use
Member states with restrictive use
Manufacturer
Brand
Type
EU: Austria, Belgium, Bulgaria, Cyprus,
Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, United Kingdom
EFTA: Switzerland, Iceland, Lichtenstein, Norway
NONE
CASIO COMPUTER CO., LTD.
CASIO
DT-X7M10E, DT-X7M10R2, DT-X7M30E, DTX7M30R
are tested and found to conform with the essential requirements for protection of health and the safety of
the user and any other persons and Electromagnetic Compatibility, as included in following standards:
Standard
EN 60950-1
EN 301 489-17
EN 50371
(for DT-X7M10R2, DTX7M30R)
lssue date
2001
v1.2.1: 2002.08
2002
and are tested and found to conform with the essential radio test suites so that they effectively use the
frequency spectrum allocated to terrestrial/space radio communication and orbital resources so to as to
avoid harmful interference, as included in following standards:
E-11
Standard
EN 300 328
EN 50371
(for DT-X7M10R2, DTX7M30R)
lssue date
v1.7.1: 2006.10
2002
and therefore comply with the essential requirements and provisions of the Directive 1999/5/EC of the
European Parliament and of the council of March 9, 1999 on Radio equipment and Telecommunications
Terminal Equipment and the mutual recognition of their conformity and with the provisions of Annex III
(Conformity Assessment procedure referred to in article 10).
The technical documentation as required by the Conformity Assessment procedure is kept at the following
address:
Company
Address, City
Country
Phone number
Fax number
CASIO Europe GmbH
Casio-Platz 1, 22848 Norderstedt
Germany
+49(0)40-528-65-0
+49(0)40-528-65-424
0984
Products are for distribution within
all member states of the EU.
France limited to 2446.5-2483.5 Mhz Indoor use.
Belgium limited to 2400-2483.5 Mhz Indoor, 2460-2483.5 Mhz Outdoor use.
The information described above dates from January 2003 and may be subjected to future
changes.
Manufacturer:
CASIO COMPUTER CO., LTD.
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Representative within the European Union:
CASIO EUROPE GmbH
Casio-Platz 1, 22848 Norderstedt, Germany
E-12
The CASIO DT-X7M10E, DT-X7M10R2, DT-X7M30E, DT-X7M30R and DT-X7M10U
models are designed, tested and found to meet the relevant regulatory standards described
below.
DT-X7M10E, DT-X7M10R2, DT-X7M30E, DT-X7M30R
International standards:
IEC 60825-1
IEC 60529, IP54 level
Europe standards:
EN 60950-1
EN 60825-1
EN 300 328
EN 301 489-17
China standards:
GB 4943
GB 9254
GB 17625.1
GB 7247.1-2001
[2002] 353
Taiwan standards:
CNS 14336
CNS 13438
LP 0002
Australia and New Zealand standards:
AS/NZS CISPR22
DT-X7M10U
International standards:
IEC 60529, IP54 level
IEC 60825-1
USA standards:
FCC Part 15B
FCC Part 15C
UL 60950-1
Canada standards:
RSS-GEN, RSS-210
ICES-003
cUL 60950-1
The DT-X7M10R2-CN and DT-X7M30R-CN for the destination of China only are designed and built to meet the Chinese
radio related regulations. These models do not permanently integrate a microphone described in this guide which disables the
capability of voice data transmission via Internet Protocol including the "VOIP". The description about the microphone is thus
intended for other models which are not available in China.
E-13
Checking in the Box
Please check the contents of the box before using the Handheld Terminal for the first
time.
Open the box and make sure that all the items shown here are included.
Handheld Terminal
Large-capacity Battery
Pack Cover
Bumper*
Hand Strap
* This is attached to the main body of
C-MOS Imager models.
User's Guide (this manual)
E-14
Handheld Terminal System Configuration
Options
USB Cradle
HA-F60IO
DT-X7 Series
Ethernet Cradle
HA-F62IO
Cradle-type Battery Charger
HA-F30CHG
The illustration shows the
USB Cradle (HA-F60IO).
Cradle-type Dual Battery Charger
HA-F36DCHG
E-15
Options
Battery Pack
HA-F20BAT
(Battery Pack)
HA-F21LBAT
(Large-capacity Battery Pack)
Dual Battery Charger
HA-F32DCHG
AC Adaptor for USB Cradle/Ethernet Cradle/
Dual Battery Charger
AD-S42120B
AD-S42120B-N
AC Adaptor for Cradle-type Battery Charger
AD-S15050BE
E-16
AD-S15050B-N
Options
AC Adaptor for Cradle-type Dual Battery Charger
AD-S60160BE
AD-S60160BU
AD-S60160B-N
Cable
DT-380USB
Power Cord for Europe
Power Cord for North America
Power Cord for Taiwan
Power Cord for Korea
Power Cord for Australia
AC-CORD-EU
AC-CORD-US
AC-CORD-TW
AC-CORD-KR
AC-CORD-AU
Hand Belt
HA-F95HB
E-17
General Guide
TOP
17
17
DT-X7M10E
DT-X7M10R2
DT-X7M30E
DT-X7M30R
Left
17
DT-X7M10U
Front
12
3
Right
Back
4
16
16
23
22
5
14
15
24
7
24
7
6
8
11
25
9
10
12
13
21
20
21
Bottom
18
19
19
1
Indicator 1
Orange: Charging the battery pack.
Green: Charging the battery pack is complete.
Red: Battery pack error or the surrounding temperature is out of
the charging temperature range.
2
Indicator 2
Flashes in blue when operating via Bluetooth or in orange when
operating via WLAN. Lights in green when reading a bar code
successfully.
3
Speaker
Buzzer and voice messages are output here.
4
Power Key
Turns the power on and off.
5
Screen
Displays text and operating instructions.
6
Trigger Center Key
Used to perform bar code reading. Can be assigned an arbitrary
function.
E-18
7
Cursor Keys
Perform the same functions as the up and down arrow keys on a
PC keyboard.
8
Enter Key
Press when finishing entering numerical values or when moving
to the next step.
9
Numeric Keys
Used to enter numeric values and decimal points.
10 Fn Key
Used to make various settings in combination with the function
keys or numeric keys or when starting a pre-registered
application.
11 CLR Key
Used to clear one letter to the left of the cursor.
12 Function Keys
Various functions other than bar code reading can be assigned to
these keys.
The default key assignments are as follows.
F1: Similar function as the Alt key on a PC keyboard.
F2: Similar function as the Shift+Tab keys combination on a PC
keyboard. Used to move the cursor among entry or selection
items.
F3: Similar function as the Tab key on a PC keyboard. Used to
move the cursor among entry or selection items.
F4: Not assigned.
F5: Enter a space.
F6: Similar function as the cursor left key on a PC keyboard.
F7: Similar function as the cursor right key on a PC keyboard.
F8: Select text entry mode.
(The mode changes in order of Numeric ➝ Uppercase letter ➝
Lowercase letter)
13 Microphone
Used to input a sound including voice.
14 Trigger R Key
Used to perform bar code reading.
15 Trigger L Key
Used to perform bar code reading.
16 Contact Scanning
Guide Attachment
Holes
Used to mount the contact scanning guide.
(DT-X7M10E/DT-X7M10R2)
17 Barcode Reader Port Laser light or LED light is emitted from this window that reads
bar codes.
18 IR Port
Used for communication with another Handheld Terminal.
19 Power Contacts
Used to receive power provided by the USB Cradle or Ethernet
Cradle.
20 Data Communication Used for data communications.
Terminal
E-19
21 Strap Holes
Used to attach the hand strap. Also used for the hand belt.
22 Reset Switch
Used to reset the Handheld Terminal.
23 Hand Belt Holes
Used to attach the hand belt.
24 Battery Pack Cover
Lock Switch
Used to lock the battery cover and to release.
25 Battery Pack Cover
Used to cover the battery compartment that holds the battery
pack inside.
E-20
Loading and Removing the Battery Pack
Your Handheld Terminal uses two types of battery: a battery pack and a memory
backup battery.
The battery pack is used to power normal operations and to store data, while the
memory backup battery provides the power required to maintain memory contents
when the battery pack power is unable to supply power for some reason.
The operating power is supplied by a battery pack. You can choose between a battery
pack (HA-F20BAT) and a large-capacity battery pack (HA-F21LBAT).
The backup battery is installed inside of the Handheld Terminal.
This guide uses the following terms to refer to the batteries.
Battery Pack:
Rechargeable battery pack (HA-F20BAT or HA-F21LBAT) for
normal operations and data storage
Backup Battery: Built-in battery for memory backup
When the battery pack power goes low, immediately charge it or replace it with a
charged battery pack.
You can use the Dual Battery Charger, the Cradle-type Battery Charger, the Cradle-type
Dual Battery Charger, the USB Cradle, or Ethernet Cradle to charge a battery pack. See
the sections of this guide that cover the Dual Battery Charger, the Cradle-type Battery
Charger, the Cradle-type Dual Battery Charger, the USB Cradle, and the Ethernet
Cradle for information about how to use them for charging.
Important!
Always keep backup copies of all important data!
• The battery pack powers normal operation and also provides power required to
maintain memory contents, while the backup battery provides backup power to
maintain memory contents. Because of this, you should not remove the battery
pack if the backup battery is dead. Removing the battery pack while the backup
battery is dead causes data in the memory to be corrupted or lost. Note that
once data is lost it cannot be recovered. Always keep separate backup copies of
all important data.
• The charge of a battery pack when you purchase it may be depleted due to
testing at the factory or natural discharge during shipment and storage. Be sure
to charge the battery pack before you use it.
• The life of a battery pack is limited, and charging a battery pack causes it to
gradually lose its ability to maintain the charge. If your battery pack seems to
require charging very frequently, it probably means it is time to purchase a new one.
• If a battery pack is used past the end of its service life, it may swell up in size. In
such a case, replace the battery pack with a new one.
• When the battery pack is attached, it takes 30 minutes for the backup battery to
obtain enough charge for maintaining memory (RAM) contents for 10 minutes.
It takes two days for the backup battery to achieve a full charge.
E-21
Loading
1. Turn over the Handheld Terminal.
2. Remove the rechargeable battery pack cover as follows:
Slide the left and right lock switches for the rechargeable battery pack cover
simultaneously in the direction indicated by the arrows.
While holding the switches back, hook your fingertips into the notches in the
rechargeable battery pack cover and lift the cover up in the direction indicated by
the arrow.
Notch
Notch
3. Load a battery pack (HA-F20BAT) or large-capacity battery pack (HA-F21LBAT).
Take care that the battery pack is oriented correctly when you load it. In addition,
load the battery back while making sure that the end of the battery pack removal tape
is protruding above the battery pack.
4. Put back the battery pack cover in the compartment as instructed by the arrows,
and
in the illustration.
E-22
After putting back the cover, firmly press the cover so that it is locked in the position by
the two Battery Pack Cover Lock Switches.
• Ensure that both the switches returned all the way down to the home positions as
indicated by the two arrows.
If the switches are lackadaisically positioned, it causes the switches not to activate.
When loading a large-capacity battery pack, use the large-capacity battery cover instead
of the standard battery cover.
Battery Pack Cover Lock Switches
Removing
1. Make sure that the Handheld Terminal is turned off.
If the power is on, press the power key to turn it off.
2. Turn over the Handheld Terminal.
3. Remove the rechargeable battery pack cover as follows:
Slide the left and right lock switches for the rechargeable battery pack cover
simultaneously in the direction indicated by the arrows.
While holding the switches back, hook your fingertips into the notches in the
rechargeable battery pack cover and lift the cover up in the direction indicated by
the arrow.
E-23
4. Remove the battery pack by pulling up the removal tape as shown in the illustration.
Loading the large-capacity battery pack into the Handheld Terminal
After loading the large-capacity battery pack, you need to use the special large-capacity
battery pack cover in place of the standard battery pack cover.
“Loading and Removing” of the large-capacity battery pack cover is the same as those
for the standard battery pack cover.
Important!
• When removing the battery pack, make sure you do not leave the Handheld
Terminal without a battery pack for more than about 10 minutes. Doing so can
cause data in the memory to be deleted.
• Never try to use other type of battery than the ones that are specified for this
product.
• When removing the battery pack, pull the removal tape straight up and remove
the battery pack. Removing with excessive force can damage the battery pack.
• Before starting to use the DT-X7, ensure that the battery pack cover is properly
closed. If not, the power cannot be turned on or is turned off abruptly while the
DT-X7 is in use.
E-24
Attaching the Hand Strap
The hand strap can be used to prevent the Handheld Terminal from dropping when
carrying it around. Since there are two strap holes where the hand strap can be attached,
use the hole that affords the ease of use. Attach the hand strap according to the
procedure described below.
To attach the hand strap
1. Pass the thin cord of the hand strap through the hand strap hole on the back of the
Handheld Terminal.
2. Pass the other end of the strap (the part you put around your hand) through the loop
formed by the thin cord.
Important!
Do not swing the Handheld Terminal around holding the hand strap.
E-25
Setting up
Using the Mouse Emulator Function
The mouse emulator function lets you make settings and adjustments by using a mouse
cursor.
To use the mouse cursor, first set up the mouse emulation mode by following the below
procedure.
In the emulation mode, the numeric keys and Trigger R key are used to
manipulate the mouse cursor. (In the emulation mode, the numeric keys and
Trigger R key cannot be used for entering numerics and scanning bar codes
respectively.)
■ Activating the mouse emulator function
• While no mouse cursor is shown on the screen, press the “Fn” key followed by the
“4” key. The mouse cursor appears, and the mouse emulator function is now active.
* To turn off the function, press the same key sequence again, i.e. “Fn” key ➝ “4” key.
* Each push of this key toggles the function between on and off.
■ Using the mouse cursor
Activate the mouse emulator function as described above.
Mouse cursor movement
• Press a numeric key for the direction in which you want to move the mouse cursor.
Mouse cursor moves
in the arrow direction.
* Holding down a key moves
the mouse cursor continuously.
Left click
This serves for selecting a file, making a menu selection, or a similar action.
• Move the mouse cursor to the position where you want to click, and press the “5”
key.
E-26
Right click (calling up a menu)
• Move the mouse cursor to the position where you want to click, and press the
Trigger R key.
Left double click
Performing this action while the mouse cursor is on an icon starts an application,
opens a file, etc.
• Move the mouse cursor to the position where you want to double click, and press
the “5” key twice.
* The double click timing follows the double tap setting of Windows CE. The setting
can be changed by accessing the “Mouse” icon in the Control Panel.
Dragging
This action allows you to move an application icon on the screen or a file or folder in
File Explorer.
• Move the mouse cursor to the position where you want to start dragging, and press
the “5” key. Then move the mouse cursor by holding down the “5” key and pressing
another numeric key for the direction in which you want to move. The selected item
will be dragged along with the cursor. When you release the “5” key, the item is
dropped at the current location.
E-27
Adjusting Display Brightness
You can use the following procedure to adjust display brightness to make it easier to
read under different lighting conditions.
• Press the “Fn” key and then press the “5” key or “6” key after confirming that “F”
is displayed in the lower right corner of the screen. Pressing the “5” key adjusts
brightness for a darker display, while pressing the “6” key adjusts brightness for a
lighter display.
* In order to continue to make adjustments, press the “5” key or “6” key after pressing
the “Fn” key.
Display Auto Dimmer
The display auto dimmer automatically lowers display brightness if you do not perform
any operation for a specific period of time. This helps the battery power to be
conserved.
You can use the following procedure to specify a period of time that should be allowed
to elapse until when the auto dimming is initiated.
1. Use the “ ”/“ ” keys to move the focus to the [Start] icon and press the Enter
key. Then navigate to Settings ➝ Control Panel with the Enter
key to bring up the Control Panel.
Focus
2. Move the focus to the “Brightness” icon and press the
Enter key. Then use the “ ”/“ ” keys to move the
focus to the tabs and use the “<”/ “>” keys to select the
[Backlight] tab. Adjust the displayed items.
* The mouse emulator function can also be used to make
the adjustment.
E-28
Using the Laser Scanner (DT-X7M10E/DT-X7M10R2)
1. After turning on the power, position the laser scanner close to a bar code and then
press the trigger key.
2. The laser emits light and scans the bar code. If scanning is completed normally,
Indicator 2 displays a green light and a buzzer sounds.
Important!
• If you are unable to scan a bar code, try changing the angle at which the scanner
is held or distance from the scanner to the bar code, and then try scanning
again.
• This Handheld Terminal is capable of scanning bar codes at a distance of
about 40-400 mm (19/16"-153/4"). Furthermore, the distance at which
scanning is possible may vary according to the bar code symbology.
Attaching the Bumper
1. Attach the Bumper on DT-X7.
2. Be sure that the Bumper and the new battery pack cover are attached on DT-X7 as
shown in the illustrations.
.
E-29
Warning Label
• This label is a warning and caution label for Class 2 laser products that comply
with IEC60825-1:1993+A1:1997+A2:2001.
• Although Class 2 laser light is only emitted momentarily, never look directly
into the beam light.
• The laser light emitted by this laser scanner has a maximum output of less than
1 mW and a wavelength of 650 nm.
• Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
Bar Code Scanning Position
Position the laser scanner close to the bar code when scanning small bar codes.
Position the laser scanner at a distance from the bar code so that the bars enter the light
when scanning large bar codes.
Margin
Good
Bad
Margin
Good
Bad
Good
Bad
Bad
Warning!
■ Never look directly into the laser light.
E-30
• The products with the integrated Laser Scanner module scan bar codes using
laser light. Never look directly into the laser light or shine the laser light
into the eyes.
Adjusting the Laser Light Emission Width
The emission width of the laser light emitted by the Handheld Terminal can be adjusted.
Adjust the emission width when it has been changed.
* The mouse emulator function can also be used to make the adjustment.
1. Use the “ ”/“ ” keys to move the focus to the [Start]
icon and press the Enter key. Then navigate to Settings
➝ Control Panel with the Enter key to bring up the
Control Panel.
2. Move the focus to the [Scanner Setting] icon and press
the Enter key. The display appears as shown at right.
3. Use the “ ”/“ ” keys to move the focus to the tabs
and use the “<”/“>” keys to select the [Others] tab.
E-31
4. Use the “ ”/“ ” keys to move the focus to
[Calibration] and press the Enter key. The message
appears as shown at right.
5. Press the Trigger Key to emit laser light, and align the
light with the barcode for adjusting emission width.
• Align the laser light with the narrow bars on both sides.
• The message appears as shown at right when adjustment
is completed.
• Repeat the setting if “Setting failed” message appears.
Emission Width Adjustment Bar Code
E-32
Using the C-MOS Imager (DT-X7M30E/DT-X7M30R)
1. Turn on the Handheld Terminal, position its C-MOS Imager reader port near the bar
code or 2D code, and then press the Trigger Key.
2. The Handheld Terminal reads the code by emitting laser and red lights.
Indicator 2 (read operation indicator lamp) lights in green when the reading is
successful.
Bar code and stacked 2D code Reading Guide
When you press the Trigger key, LEDs in the Handheld Terminal emit laser and red
lights. Align the laser frame with the center of the bar code or 2D code you are trying
to read. Take particular care aligning the light when there are other bar codes nearby.
When reading a bar code in large size, adjust the position of the Handheld Terminal
so that the entire code is enclosed within the laser frame. For small size, move the
Handheld Terminal closer to it.
Important!
• If you have problem not properly reading a code, change the angle and/or the
distance between the code and the Handheld Terminal and try reading it again.
• A bar code can be read from a distance of 40mm to 410mm (19/16" to 161/8"),
and a stacked 2D code can be read from a distance of 50mm to 250mm (115/16"
to 913/16") and matrix 2D code can be read from a distance of 60mm to 150mm
(23/8" to 515/16"). The actual reading distance depends on the symbology and the
resolution.
• Note that a special reader application is required to read bar codes and 2D
codes.
• Fingerprints, dust, dirt, or stain on the C-MOS Imager reader port can cause
abnormal reading. Should the reader port become dirty, wipe it clean with a soft
and dry cloth.
E-33
Warning Label
DT-X7M30E
DT-X7M30R
DT-X7M30R-CN
• This label is a warning and caution label for Class 2 laser products that comply
with IEC60825-1:1993+A1:1997+A2:2001.
• Although Class 2 laser light is only emitted momentarily, never look directly into
the beam light.
• The laser light emitted by this laser scanner has a maximum output of less than
1 mW and a wavelength of 650 nm.
• Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
Warning!
„ Never look directly into the laser light.
• The products with the integrated C-MOS Imager module scan bar codes
using laser light. Never look directly into the laser light or shine the laser
light into the eyes.
E-34
Using the Linear Imager (DT-X7M10U)
1. After turning on the power, position the reader port close to a bar code and then press
the Trigger key.
2. The LED emits light and scans the bar code. When scanning is completed normally,
Indicator 2 displays a green light and a buzzer sounds.
Important!
• If you are unable to scan a bar code, try changing the angle at which the
Handheld Terminal is held or distance between the reader port and the bar
code, and then try scanning again.
• This Handheld Terminal is capable of scanning bar codes at a distance of
about 60-300 mm (26/16"-1113/16"). Furthermore, the distance at which scanning
is possible may vary according to the bar code symbology.
Warning Label
Warning!
■ Never look directly into the LED light.
• This product scans using LED light. Never look directly into the LED light
or shine the LED light into the eyes.
About the Class 1 LED Label
• This label identifies the Handheld Terminal as a Class 1 LED product
compliant with IEC60825-1 (ed.1.2).
E-35
Performing Communications
IR Communication
IR communication can be used to transmit data between two Handheld Terminals.
When performing IR communication, orient the IR ports of both Handheld Terminals
so they are pointing directly at each other.
The ports can be in direct contact with each other, or they can be separated by up to
30cm (1113⁄16") (up to 20cm (7 7⁄8") for communication between units).
Important!
• A high-sensitivity communication element is used during IR communication.
• In order to ensure successful communication, avoid using cellular phones or
other devices that emit radio wave in the area where you are performing IR
communication.
• If you need to use such a device, move away from the communicating Handheld
Terminals. In case of a cellular phone, keep it at least 30cm (1113⁄16") away.
E-36
Bluetooth® Communication
Bluetooth® interface can also be used to transmit data between two Handheld Terminals.
With Bluetooth® the two Handheld Terminals should be located within about three meters
(9'103⁄8") (Laser Scanning and C-MOS Imager models) or 100 meters (328'1") (DTX7M10U) from each other, as long as there is nothing blocking the path between them.
Important!
Observe the following precautions to help ensure that Bluetooth communication is
successful.
• Make sure there is at least two meters (6'7") between the Handheld Terminal and
other equipment (electrical appliances, audio-visual equipment, OA equipment,
and digital cordless telephones, facsimile machines, etc.). (Take special care with
microwave ovens. Allow at least three meters (9'103⁄8) between the Handheld
Terminals in wireless operation and a microwave oven.) When approaching such a
device when its power is turned on, proper communication may prove impossible
while this may also cause interference with TV and radio reception (images
produced by certain UHF and broadcast satellite channels may become blurry).
• Normal communication may not be possible in an area near a broadcast transmitter or wireless transmitter. If this happens, move the Handheld Terminal to a
different location. Normal communication may not be possible in areas exposed
to strong radio waves.
• RF Wireless LAN Interference
Because Bluetooth® and RF wireless LAN use the same frequency band
(2.4GHz), radio interference can occur if there is a wireless LAN device nearby.
This can result in lower communication speeds, or even make it impossible to
establish a connection. If this happens, try the following countermeasures.
• Move at least 10 meters (32'103⁄4") away from the wireless LAN device.
• If you cannot keep the distance at least 10 meters (32'103⁄4") or more between the
Handheld Terminal and a wireless LAN device, turn off the power of either the
Handheld Terminal or the wireless LAN device.
®
• Although the Handheld Terminal enables wireless LAN and Bluetooth
communication to be used simultaneously as a result of being equipped with
Bluetooth® Ver.2.0, communication may not be possible depending on the
surrounding radio wave environment.
E-37
Resetting the Handheld Terminal
Resetting the Handheld Terminal is the same as restarting a PC. Performing a reset
causes all unsaved inputs and edits to be lost, but data that is already stored in the
memory as well as all settings should be unaffected.
Use reset to restore normal operation whenever the Handheld Terminal operates
abnormally due to misoperation or some other reason.
Use a stylus to press the reset switch on the back of the DT-X7.
This starts the reset operation.
* Do not use a toothpick or pencil or other object
whose tip may break off when pressing the reset
switch. Otherwise there is a risk of damage.
If reset does not find a memory problem
The Handheld Terminal restarts, and normal operation is restored.
If reset finds a memory problem
A message like the one shown below appears on the display when the reset operation
discovers a memory problem.
Trigger R
Key
When this message appears, press the Trigger key to continue with the reset operation.
Note, however, that reset may not be successful depending on the condition of the
memory. In this case, perform the full reset operation described on the next page.
E-38
Performing a Full Reset (Initialization)
Performing a full reset initializes memory. This means that all data stored in the
memory (RAM) is deleted and all the settings are returned to their initial factory
settings.
Perform a full reset whenever any one of the following conditions exists.
• When you want to delete all memory contents and return the settings to their initial
factory settings.
• When you are no longer able to use the Handheld Terminal because you forgot your
password.
• When the Handheld Terminal does not operate normally due to a memory problem.
• When the message “A problem with memory contents has been found. ...” appears.
To perform a full reset
Important!
Performing a full reset deletes all data currently stored in the memory (RAM).
If possible, backup data of the Handheld Terminal to a PC, Flash Memory, a
memory card, or some other medium before performing a full reset.
1. While holding down the Power key and CLR key simultaneously, press the reset
swicth using stylus for approximately one second and then release the reset switch
first. The message shown below appears.
• To cancel the full reset operation, press the Trigger L key.
Trigger R
Key
2. Press the Trigger R key. This causes the message shown below to appear.
• To cancel the full reset operation, press the Trigger L key.
Trigger R
Key
3. Press the Trigger R key again.
• Full reset is performed, all data in the memory (RAM) are erased and the start-up
screen is displayed.
E-39
DT-X7 Specifications
Model:
DT-X7M10E, DT-X7M10R2, DT-X7M10U, DT-X7M30E,
DT-X7M30R
CPU:
Marvell® PXA270 416MHz
Memory:
64MB RAM, 64MB Flash ROM (user area: approx. 28MB)
OS:
Microsoft® Windows® CE5.0 operating system,
English Version
Display:
2.4-inch, 320 × 240-dot transflective TFT color LCD
Laser Scanner (DT-X7M10E, DT-X7M10R2):
Readable symbologies: UPC-A, UPC-E, EAN8 (JAN8), EAN13 (JAN13), Codabar
(NW-7), Code39, Interleaved 2 of 5 (ITF), MSI, Industrial 2 of 5,
Code93, Code128 (EAN128), IATA, RSS-14, RSS Limited,
RSS Expanded, RSS-14 Stacked, RSS Expanded Stacked*
* RSS was renamed as GS1 DataBar in February 2007.
Scanning distance: Within approximately 40-400 mm (19/16"-153/4")
Linear Imager (DT-X7M10U):
Readable symbologies: UPC-A, UPC-E, EAN8 (JAN8), EAN13 (JAN13), Codabar
(NW-7), Code39, Interleaved 2 of 5 (ITF), MSI, Industrial 2 of 5,
Code93, Code128 (EAN128), IATA, RSS-14, RSS Limited,
RSS Expanded, RSS-14 Stacked, RSS Expanded Stacked
* RSS was renamed as GS1 DataBar in February 2007.
Scanning distance: Within approximately 60-300 mm (26/16"-1113/16")
C-MOS Imager (DT-X7M30E, DT-X7M30R):
Readable symbologies: 1D: UPC-A/UPC-E/EAN8 (JAN8)/EAN13 (JAN13)/Codabar
(NW-7)/Code39/Interleaved 2 of 5 (ITF)/MSI/Code93/
Code128 (EAN128 (GS1-128))/Code11/IATA/RSS-14 (GS1
DataBar Omnidirectional)/RSS Limited (GS1 DataBar Limited)/
RSS Expanded (GS1 DataBar Expanded)
Stacked 2D: PDF417/Micro PDF/CODE49/Composite/
Codablock F/TLC39/RSS Expanded Stacked (GS1 DataBar
Expanded Stacked)/RSS-14 Stacked (GS1 DataBar Stacked)
Matrix 2D: Aztec/DataMatrix/Maxicode/QR Code
Scanning distance:
1D: 40 – 410 mm (19/16"-161/8")
Stacked 2D: 50 – 250 mm (1911/16"-913/16")
Matrix 2D: 60 – 150 mm (23/8"-57/8")
IR Port:
Interface: IrDA Ver. 1.3 LowPower
Synchronization: Asynchronous, frame synchronization
Transmission rate: Up to 4Mbps (max.)
Bluetooth® (Laser Scanner and C-MOS Imager models):
Protocol: Bluetooth® Specification Ver.2.0
Range: Approximately 3 m (9'103/8") (depends on radio wave conditions
and environment)
Output: 4dBm max. (PowerClass2)
Bluetooth® (DT-X7M10U):
Protocol: Bluetooth® Specification Ver.2.0
Range: Approximately 100 m (328'1") (depends on radio wave
conditions and environment)
Output: 12dBm max. (PowerClass1)
E-40
WLAN(DT-X7M10R2, DT-X7M30R):
Standards: Complies with IEEE 802.11b/g
Diffusion Modulation: DS: 802.11b
DS/OFDM: 802.11g
Frequency: 802.11b/g: 2.400-2.4835 GHz
Transmission Rate: 802.11b: Max. 11 Mbps
802.11g: Max. 54 Mbps
Communication Range: 50 m indoors, 150 m outdoors (varies according to usage
environment and transmission rate)
Power Requirements:
Power Source: HA-F20BAT Battery Pack
HA-F21LBAT Large-capacity Battery Pack
Memory Backup: Rechargeable Lithium Battery (Built-in)
Consumption Current: DC 1.3A (DT-X7M10E)
DC 1.6A (DT-X7M10R2)
DC 1.4A (DT-X7M10U, DT-X7M30E)
DC 1.7A (DT-X7M30R)
Battery Life:
Battery pack:
DT-X7M10E/DT-X7M10U/DT-X7M30E
Approximately 15 hours (HA-F20BAT)*
Approximately 26 hours (HA-F21LBAT)*
DT-X7M10R2/DT-X7M30R
Approximately 15 hours (HA-F20BAT)*
Approximately 26 hours (HA-F21LBAT)*
Approximately 10 hours (HA-F20BAT)**
Approximately 17 hours (HA-F21LBAT)**
* under the conditions that CPU speed is set to the auto power
save mode, backlight is set to off, and the ratio of cyclic
operation of “Standby, Key input, and Scanning” is set at
20:1:1.
** under the conditions that CPU speed is set to the auto
power save mode, backlight is set to off, and the ratio of
cyclic operation of “Standby, Key input, Scanning, and
WLAN” is set at 20:1:1:1.
Memory backup: 10 minutes for protection of data in memory
3 days for backup of built-in clock
Operating Temperature: –10°C to 50°C (14°F to 122°F)
Operating Humidity:
10% to 80% RH (non-condensation)
Dust and Water Splash Proof:
IEC60529 standard, IP54 level
Dimensions:
Refer to “Dimensional Drawing” on the next page.
Weight:
DT-X7M10E, DT-X7M10R2:
Approximately 145g (5.1oz) (when standard battery pack is
installed)
DT-X7M10U:
Approximotely 155g (5.5oz) (when standard battery pack is
installed)
DT-X7M30E, DT-X7M30R:
Approximotely 160g (5.6oz) (when standard battery pack and
bumper are installed)
Vibrator Function:
Available according to software setting.
E-41
Dimensional Drawings
Approx.
52.5mm (21/16")
(Display)
Approx.
51mm (2")
(Grip)
E-42
Approx.
23.5mm (15/16")
(Display)
Approx.
30.5mm (13/16")
(Grip)
Approx. 166mm (69/16")
For Laser Scanner Models
Linear Imager Model
Approx.
52.5mm (21/16")
(Display)
Approx.
51mm (2")
(Grip)
Approx.
23.5mm (15/16")
(Display)
Approx.
30.5mm (13/16")
(Grip)
Approx. 169mm (65/8")
For C-MOS Imager Models
E-43
Using the USB Cradle (HA-F60IO)
The optionally available USB Cradle (HA-F60IO) makes it possible to transmit
data and files between the Handheld Terminal and a PC via a USB connection
(download or upload). You can also use the USB Cradle to charge the battery pack
installed in the Handheld Terminal.
General Guide
Top
7
5
6
Front
8
E-44
Back
Left
3
4
2
1
1
USB Client Port
This port is used to transmit data and files (download, upload) by
connecting the Cradle to a PC using a USB cable (DT-380USB).
A dedicated driver must be installed in the PC before connecting
the Cradle to the PC.
2
USB Host Port
This port is used to connect a corresponding USB peripheral
device.
3
Selector Switch
This switch is used to switch between the USB host port and
USB client port.
4
AC Adaptor Jack
Connect the AC adaptor here.
5
Terminal Detect
Switch
This switch detects when the DT-X7 is seated correctly on the
Cradle.
6
Power Contacts
Power is supplied to the DT-X7 via these contacts.
7
Data
Communication
Terminal
Used for USB communications.
8
Power LED
This LED indicates the power status and the mounting status of
the DT-X7.
Off: DT-X7 is not installed. Or, the AC adaptor is not connected.
Green: Power on, DT-X7 mounted correctly.
E-45
Connecting the USB Cradle Power Supply
Use the separately sold AC adaptor (AD-S42120B) for the power supply of the USB
Cradle. Always make sure to connect the AC adaptor to the USB Cradle before
performing communication with the Handheld Terminal. Power to the Handheld
Terminal is supplied from the USB Cradle.
1. Plug the AC adaptor into the AC adaptor jack on the back of the USB Cradle.
2. After connecting the power cable to the AC adaptor, plug the other end of it into an
electrical outlet.
3. Use the selector switch on the left side of the USB Cradle to select the port to be used.
Set the switch to the “B” position when using the unit as a USB client, or set it to the “A”
position when using the unit as a USB host.
E-46
4. Connect the USB cable (DT-380USB) to the USB client port on the back of the USB
Cradle, and then connect it to the PC. The USB host port is used when connecting the
cradle with other USB peripheral device.
PC
USB peripheral device
5. Align the contacts on the bottom of the DT-X7 with the power contacts of the
USB Cradle when inserting the unit.
The power LED on the front of the USB Cradle will light green if the Handheld
Terminal has been properly mounted.
Status of Indicator 1 on DT-X7:
Orange: Charging the battery pack.
Red:
Standby due to battery pack error or the surrounding temperature is out of the
charging temperature range.
(charging begins when the temperature is within the charging temperature range)
Green: Charging the battery pack is complete.
Important!
• Always make sure to first remove the Handheld Terminal from the USB Cradle
when switching the selector switch.
• Allowing the power contacts become wet can cause an electric shock or fire. In
addition, if the contacts become soiled, contact may be impaired resulting in
poor charging. For reasons of safety and maintaining charging battery pack(s)
in optimum condition, clean the power contacts by wiping with a dry cloth or
cotton swab after disconnecting the AC adaptor.
• Never short out the power contacts of the USB Cradle. This can damage the
USB Cradle.
E-47
• Do not subject the Handheld Terminal and USB Cradle to vibration or impact
during communication. This can cause communication to be interrupted.
• When placing the DT-X7, make sure that it is seated properly and that the power
LED at the front of the USB Cradle is lit in green. Charging and communication
will not proceed properly if the Handheld Terminal is not seated properly.
• Always cap ports that are not being used. Using the USB Cradle while the ports
are uncapped can cause damage.
Specifications
1. USB
Protocol:
Transfer Rate:
2. Charging
Charging Method:
Charge Period:
3. Power Supply
Power Source:
Consumption Current:
Output to Handheld Terminal:
USB Host Output:
4. AC Adaptor
Model:
Input:
Output:
5. Dimensions and Weight
Dimensions:
Weight:
6. Operating Environment
Temperature:
Humidity:
USB Ver1.1 Standard
12Mbps (max.)
Constant current/voltage
Approximately 3 hours (battery pack)
Approximately 5.5 hours (large-capacity battery pack)
AC adaptor (AD-S42120B)
12V DC approximately 1.3A
5V DC 1.6A (max.)
5V DC 0.5A (max.)
AD-S42120B
100V to 240V AC 50/60Hz 1.2A
12V DC 3.5A
Approximately 93(W) × 83(D) × 101(H) mm
(311⁄16"W × 31⁄4"D × 4"H)
Approximately 270g (9.5oz)
0°C to 40°C (32°F to 104°F)
30% to 80% RH (non-condensation)
The AD-S42120 series comes available in the following models depending on area or region
where you are in.
E-48
Model no. of AC Adaptor
AD-S42120B
Area/Region
All except China
AD-S42120B-CN
China only
Compliance
Compliant with CE,
UL, FCC, and Energy
Efficiency Standards.
Compliant with Energy
Efficiency Standards and
CCC.
Using the Ethernet Cradle (HA-F62IO)
The optionally available Enthernet Cradle (HA-F62IO) makes it possible to
transmit data and files between the Handheld Terminal and a PC via a USB or LAN
connection (download or upload). You can also use the Ethernet Cradle to charge
the battery pack installed in the Handheld Terminal.
General Guide
Top
10
8
9
Front
Left
Back
6
7
11
3
5 4 2
1
E-49
1
USB Client Port
This port is used to transmit data and files (download, upload)
by connecting the Ethernet Cradle to a PC using a USB cable
(DT-380USB). The dedicated driver must be installed in the PC
before connecting the Ethernet Cradle to the PC.
2
USB Host Port
This port is used to connect a corresponding USB peripheral
device.
3
Selector Switch
This switch is used to switch between a USB connection and a
LAN connection.
4
LAN Connection
Status LED
This LED shows the status of the LAN connection.
Off: LAN cable not connected correctly.
Lit green: LAN cable connected correctly.
5
LAN
Communication
Status LED
This LED shows the LAN operation status.
Off: No communication.
Blinking green: Communication in progress.
6
LAN Port
This port is used for connecting the cradle to a PC or hub via a
LAN cable so that data and files can be transmitted (uploaded or
downloaded).
The special driver software must be installed in the DT-X7.
7
AC Adaptor Jack
Connect the AC adaptor here.
8
Terminal Detect
Switch
This switch detects when the DT-X7 is seated correctly on the
Ethernet Cradle.
9
Power Contacts
Power is supplied to the DT-X7 via these contacts.
10 Communication
Terminal
Used for communications.
11
This LED indicates the power status and the mounting status of
the DT-X7.
Off: DT-X7 is not installed. Or, the AC adaptor is not connected.
Green: Power on, DT-X7 mounted correctly.
E-50
Power LED
Connecting the Ethernet Cradle Power Supply
Use the separately sold AC adaptor (AD-S42120B) for the power supply of the
Ethernet Cradle. Always make sure to connect the AC adaptor to the Ethernet Cradle
before performing communication with the Handheld Terminal. Power to the Handheld
Terminal is supplied from the Ethernet Cradle.
1. Plug the AC adaptor into the AC adaptor jack on the back of the Ethernet Cradle.
2. After connecting the power cable to the AC adaptor, plug the other end of it into an
electrical outlet.
3. Use the selector switch on the left side of the Ethernet Cradle to select the port to be
used. Set the switch to the “LAN” position when using the LAN port on the cradle.
Set the switch to the “B” position when using the unit as a USB client, or set it to the
“A” position when using the unit as a USB host.
E-51
4. Before using the cradle ports, remove the caps from the ports.
When using a LAN, connect one end of the LAN cable to the LAN port and the other end to
the PC or hub.
When using a USB connection, connect one end of the USB cable (DT-380USB) to the
USB port and the other end to the PC.
The USB host port is used for connecting the cradle with other USB peripheral device.
PC
PC or hub
5. Align the contacts on the bottom of the DT-X7 with the power contacts of the
Ethernet Cradle when inserting the unit.
The power LED on the front of the Ethernet Cradle will light green if the Handheld
Terminal has been properly mounted.
Status of Indicator 1 on DT-X7:
Orange: Charging the battery pack.
Red:
Standby due to battery pack error or the surrounding temperature is out of the
charging temperature range.
(charging begins when the temperature is within the charging temperature range)
Green: Charging the battery pack is complete.
Important!
• Always make sure to first remove the Handheld Terminal from the Ethernet
Cradle when switching the selector switch.
• Allowing the power contacts become wet can cause an electric shock or fire. In
addition, if the contacts become soiled, contact may be impaired resulting in
poor charging. For reasons of safety and maintaining charging battery pack(s)
in optimum condition, clean the power contacts by wiping with a dry cloth or
cotton swab after disconnecting the AC adaptor.
• Never short out the power contacts of the Ethernet Cradle. This can damage the
Ethernet Cradle.
• Do not subject the Handheld Terminal and Ethernet Cradle to vibration or
impact during communication. This can cause communication to be interrupted.
E-52
• When placing the DT-X7, make sure that it is seated properly and that the
power LED at the front of the Ethernet Cradle is lit in green. Charging and
communication will not proceed properly if the Handheld Terminal is not
mounted properly.
• Always cap ports that are not being used. Using the Ethernet Cradle while the
ports are uncapped can cause damage.
Specifications
1. LAN Specifications
Communications protocol:
Media type:
2. USB
Protocol:
Transmission rate:
3. Charging
Charging Method:
Charge Period:
4. Power Supply
Power Source:
Consumption Current:
Output to Handheld Terminal:
USB Host Output:
5. AC Adaptor
Model:
Input:
Output:
6. Dimensions and Weight
Dimensions:
Weight:
7. Operating Environment
Temperature:
Humidity:
IEEE 802.3
10base-T/100base-TX auto-switched
USB Ver1.1 Standard
12Mbps (max.)
Constant current/voltage
Approximately 3 hours (battery pack)
Approximately 5.5 hours (large-capacity battery pack)
AC adaptor (AD-S42120B*)
12V DC approximately 1.5A
5V DC 1.6A (max.)
5V DC 0.5A (max.)
AD-S42120B
100V to 240V AC 50/60Hz 1.2A
12V DC 3.5A
Approximately 93(W) × 83(D) × 101(H) mm
(311⁄16"W × 31⁄4"D × 4"H)
Approximately 280g (9.9oz)
0°C to 40°C (32°F to 104°F)
30% to 80% RH (non-condensation)
*See page 47.
E-53
Using the Cradle-type Battery Charger (HA-F30CHG)
The optionally available Cradle-type Battery Charger (HA-F30CHG) lets you charge
the Handheld Terminal’s battery simply by placing the Handheld Terminal onto the
charger.
General Guide
Top
2
3
Front
Left
4
Back
1
1
AC Adaptor Jack
Connect the AC adaptor here.
2
Terminal Detect
Switch
This switch detects when the DT-X7 is mounted correctly on the
charger.
3
Power Contacts
Power is supplied to the DT-X7 via these contacts.
4
Power LED
This LED indicates the power status and the mounting status of
the Handheld Terminal.
Off: DT-X7 is not installed
Green: Power on, DT-X7 mounted correctly
E-54
Connecting the AC Adaptor for Cradle-type Battery Charger
Use the separately sold AC adaptor (AD-S15050BE) for the power supply of the
Cradle-type Battery Charger.
1. Plug the AC adaptor into the AC adaptor jack on the back of the charger.
2. Next, plug the AC adaptor into a wall outlet.
3. Align the contacts on the bottom of the DT-X7 with the power contacts of the Cradletype Battery Charger when inserting the unit.
The power LED on the front of the charger will light green if the Handheld Terminal
has been properly mounted.
E-55
Status of Indicator 1 on DT-X7:
Orange: Charging the battery pack.
Red:
Standby due to battery pack error or the surrounding temperature is out of the
charging temperature range.
(charging begins when the temperature is within the charging temperature range)
Green: Charging the battery pack is complete.
Important !
• Never short out the power contacts of the Cradle-type Battery Charger. This
can damage the Cradle-type Battery Charger.
• Allowing the power contacts become wet can cause an electric shock or fire. In
addition, if the contacts become soiled, contact may be impaired resulting in
poor charging. For reasons of safety and maintaining charging battery pack(s)
in optimum condition, clean the power contacts by wiping with a dry cloth or
cotton swab after disconnecting the AC adaptor.
• When placing the DT-X7, make sure that it is seated properly and that the power
LED at the front of the Cradle-type Battery Charger is lit in green. Charging and
communication will not proceed properly if the Handheld Terminal is not seated
properly.
E-56
Specifications
1. Charging Specifications
Charging Method:
Charge Period:
2. Power Supply
Power Source:
Consumption Current:
Output to Handheld Terminal:
3. AC Adaptor
Model:
Input:
Output:
4. Dimensions and Weight
Dimensions:
Weight:
5. Operating Environment
Temperature:
Humidity:
Constant current/voltage
Approximately 3 hours (battery pack)
Approximately 5.5 hours (large-capacity battery pack)
AC adaptor (AD-S15050BE)
5V DC 1.6A
5V DC 1.6A (max.)
AD-S15050B
100V to 240V AC 50/60Hz 0.4A
5V DC 3.0A
Approximately 93(W) × 83(D) × 101(H) mm
(311⁄16"W × 31⁄4"D × 4"H)
Approximately 230g (8.1oz)
0°C to 40°C (32°F to 104°F)
30% to 80% RH (non-condensation)
The AD-S15050 series comes available in the following models depending on area or region
where you are in.
Model no. of AC Adaptor
AD-S15050BE
Area/Region
All except China
AD-S15050BE-CN
China only
Compliance
Compliant with CE,
UL, FCC, and Energy
Efficiency Standards.
Compliant with Energy
Efficiency Standards and
CCC.
E-57
Using the Cradle-type Dual Battery Charger (HA-F36DCHG)
The optionally available Cradle-type Dual Battery Charger (HA-F36DCHG) can be
used to simultaneously charge two battery packs.
General Guide
Left
Top
1
2
4
Right
4
Bottom
2
Front
3
1
AC Adaptor Jack
This is used to supply power by connecting the AC adaptor (sold
separately).
2
Cradle-type Dual
Battery Charger
Connection Port
Use this port to connect multiple Cradle-type Dual Battery
Chargers to each other.
3
Connection
Bracket
Attachment Holes
The connection bracket attaches here when you connect multiple
Cradle-type Dual Battery Chargers to each other.
4
Power Contacts
Power is supplied to the Handheld Terminal via these contacts.
E-58
Bundled Items
Used when linking two or more Cradle-type Dual Battery Chargers.
x Connection
bracket (for rear)
x Connection
bracket (for side)
x Connection screws
(for rear and side),
2 each
E-59
Charging Battery Pack
Use the separately sold AC adaptor (AD-S60160BE/AD-S60160BU) for the power
supply of the Cradle-type Dual Battery Charger.
1. Plug the cord from the AC adaptor into the AC adaptor jack of the Cradle-type Dual
Battery Charger.
2. Plug the AC cord into a wall outlet.
AC Adaptor
AC Adaptor Jack
3. Align the contacts on the bottom of the DT-X7 with the power contacts of the Cradletype Dual Battery Charger when inserting the unit.
- Check the charging status with Indicator 1 on the DT-X7.
Status of Indicator 1 on DT-X7
Orange: Charging the battery pack.
Red:
Battery pack problem, or standby due to the surrounding temperature being
beyond the specified temperature range (charging resumes when the
temperature reaches the range).
Green: Charging the battery pack is complete.
E-60
Connecting Multiple Cradle-type Dual Battery Chargers
You can connect up to three Cradle-type Dual Battery Chargers. Doing so makes
it possible to supply power to all the Cradle-type Dual Battery Chargers using one
dedicated AC adaptor.
1. As shown in the illustrations below, remove the connector covers of the Cradle-type
Dual Battery Chargers you want to connect to each other.
Connector cover
2. Connect the two Cradle-type Dual Battery Chargers as shown below.
Cradle-type Dual Battery
Charger link connector
3. Attach the rear and side connection brackets with the connection screws.
You can repeat the above steps to connect up to 3 Cradle-type Dual Battery Chargers.
* Attach the connection brackets so that the front side faces outwards. (The front side
has protruding ribs.)
Connection brackets
Rib
Side
Rear
Rib
E-61
Specifications
1. Charging Specification
Charging Method:
Charge Period:
Constant current/voltage
Approx. 3 hours (1 standard battery pack)
Approx. 5.5 hours (1 large-capacity battery pack)
2. Power Supply
Power Source:
Consumption Current:
AC adaptor (AD-S60160BE/AD-S60160BU)
1.25A, 16V DC (1 unit)
3.7A, 16V DC (3 units)
Output to Handheld Terminal: 5V DC 1.6A (max.)
3. AC Adaptor
Model:
AD-S60160B
Input:
100V to 240V AC 50/60 Hz 1.5A
Output:
16V DC 3.0A
4. Dimensions and Weight
Dimensions:
Approximately 189(W) × 80(D) × 110(H) mm
(77⁄16"W × 31⁄8"D × 45⁄16"H)
Weight:
Approximately 500g (17.6oz)
5. Operating Environment
Temperature:
Approximately 0°C to 40°C (32°F to 104°F)
Humidity:
30% to 80% RH (non-condensation)
The AD-S60160 series comes available in the following models depending on area or region
where you are in.
E-62
Model no. of AC Adaptor
AD-S60160BE
Area/Region
All except China, USA,
and Canada
AD-S60160BE-CN
China only
AD-S60160BU
USA and Canada
Compliance
Compliant with CE
and Energy Efficiency
Standards.
Compliant with Energy
Efficiency Standards and
CCC.
Compliant with UL, FCC,
and Energy Efficiency
Standards.
Important !
• Never short out the power contacts of the Cradle-type Dual Battery Charger.
This can damage the Cradle-type Dual Battery Charger.
• Allowing the power contacts become wet can cause an electric shock or fire. In
addition, if the contacts become soiled, contact may be impaired resulting in
poor charging. For reasons of safety and maintaining charging battery pack(s)
in optimum condition, clean the power contacts by wiping with a dry cloth or
cotton swab after disconnecting the AC adaptor.
• Place the Handheld Terminal in the Cradle-type Dual Battery Charger. Check
the Indicator 1 on the terminal to ensure that it has been securely positioned in
the charger. The indicator will light up in orange for correct positioning.
• Each unit of the charger comes with one piece each of the side and bottom brackets.
After you join two chargers together using these two brackets, one side bracket and
one bottom bracket will be left over. Keep these as spare for use in future.
• Before linking multiple Cradle-type Dual Battery Chargers, be sure to
disconnect the AC adaptor.
• Turn off the power on DT-X7 before placing it in the charger.
E-63
Using the Dual Battery Charger (HA-F32DCHG)
The optionally available Dual Battery Charger (HA-F32DCHG) can be used to
simultaneously charge two battery packs.
General Guide
Left
Top
1
3
Bottom
Right
2
3
Front
4
Bundled Items
Connection Bracket
2 screws
5
E-64
1
Charge Indicator
LED
This LED indicates the charge status of the battery pack(s).
Off: Not charging the battery pack.
Red: Charging the battery pack.
Red Flashing: Battery pack problem
Green Flashing: Standby
Green: Charging the battery pack is complete.
2
AC Adaptor Jack
This is used to supply power by connecting the AC adaptor (sold
separately).
3
Dual Battery
Charger
Connection Port
Use this port to connect multiple Dual Battery Chargers to each
other.
4
Connection
Bracket
Attachment Holes
The connection bracket attaches here when you connect multiple
Dual Battery Chargers to each other.
5
Power Contacts
Power is supplied to the Handheld Terminal via these contacts.
Important!
• Allowing the power contacts become wet can cause an electric shock or fire. In
addition, if the contacts become soiled, contact may be impaired resulting in
poor charging. For reasons of safety and maintaining charging battery pack(s)
in optimum condition, clean the power contacts by wiping with a dry cloth or
cotton swab after disconnecting the AC adaptor.
• Although the battery may become warm during charging, this is normal and
does not indicate a malfunction.
• Do not remove the battery pack or disconnect the AC adaptor during charging.
• Repeated “Mounting and Removing” of battery pack in excess of times may
cause the quality deterioration of the battery pack.
• Each Dual Battery Charger comes with one connection bracket.
Since only one connection bracket is required when you connect two Dual
Battery Chargers, you will always have one left over.
Simply keep the other connection bracket on hand as an extra, in case you ever
need it.
E-65
Charging Battery Pack
Use the separately sold AC adaptor (AD-S42120B) for the power supply of the Dual
Battery Charger.
1. Plug the cord from the AC adaptor into the AC adaptor jack of the Dual Battery
Charger.
2. Plug the AC cord into a wall outlet.
3.Taking care that the battery pack is oriented correctly, insert it into the Dual Battery
Charger.
This causes the Charge Indicator LED to light in red, indicating that charging has
started.
Status of Charge Indicator LED
Off:
Red:
Red Flashing:
Green:
Green Flashing:
E-66
Not charging the battery pack.
Charging the battery pack.
Battery pack problem
Charging the battery pack is complete.
Standby due to the surrounding temperature being beyond the
specified temperature range (approximately 0°- 40°C). (charging
resumes when the temperature reaches the range)
Connecting Multiple Dual Battery Chargers
You can connect up to three Dual Battery Chargers. Doing so makes it possible to
supply power to all the Dual Battery Chargers using one dedicated AC adaptor.
1. As shown in the illustrations below, remove the connector covers of the Dual Battery
Chargers you want to connect to each other.
Connector cover
2. Connect the two Dual Battery Chargers as shown below.
3. Turn over the connected Dual Battery Chargers and attach a connection bracket,
securing it in place with screws.
You can repeat the above steps to connect up to 3 Dual Battery Chargers.
E-67
Specifications
1. Charging Specification
Charging Method:
Charge Period:
Constant current/voltage
Approx. 3 hours (1 standard battery pack, normal temperature)
Approx. 5.5 hours (1 large-capacity battery pack, normal
temperature)
When charging two battery packs:
Approx. 5.5 hours (2 standard battery packs, normal
temperature)
Approx. 10 hours (2 large-capacity battery packs, normal
temperature)
2. Power Supply
Power Source:
Consumption Current:
Output:
AC adaptor (AD-S42120B*)
12V DC 3.5A
4.2V DC 1.1A (max.)
3. AC Adaptor
Model:
Input:
Output:
AD-S42120B
100V to 240V AC 50/60Hz 1.2A
12V DC 3.5A
4. Dimensions and Weight
Dimensions:
Weight:
5. Operating Environment
Temperature:
Humidity:
*See page 47
E-68
Approximately 108(W) × 104(D) × 45(H) mm
(41⁄4"W × 41⁄8"D × 13⁄4"H)
Approximately 152g (5.4oz)
Approximately 0°C to 40°C (32°F to 104°F)
30% to 80% RH (non-condensation)
Using Rechargeable Battery Pack
HA-F20BAT
HA-F21LBAT
Your Handheld Terminal supports use of two battery pack types, one at a time, of
different capacity.
You can select the one that best suits your needs in terms of operating time, the type of
options you need to use, etc.
When using the large-capacity battery pack, you need to use the special large-capacity
battery pack cover that comes with the battery pack (HA-F21LBAT).
Important!
• Store a battery pack in its special soft case whenever you are not using it.
• If the battery pack has been left over unused for a long period of time, the
capacity remained decreases due to spontaneous discharge or chemical
decomposition by the battery pack itself. If the battery pack fails to hold its
operating duration after it has been fully charged, replace it with a new one. The
battery pack may reach the end of its service life.
th
• Follow the packing instruction promulgated in the IATA DGR 50 regulations
to transport lithium-ion battery packs.
E-69
Battery Pack Specifications
Model:
HA-F20BAT
Rated Capacity:
4.07WH (1100mAh)
Rated Voltage:
3.7V
Dimensions:
Approximately 36(W) × 55(D)
× 9(H) mm (17⁄16"W × 23⁄16"D × 3⁄8"H)
Weight:
Approximately 28g (1oz)
Bundled Item:
Soft case
Large-capacity Battery Pack Specifications
Model:
HA-F21LBAT
Rated Capacity:
6.956WH (1880mAh)
Rated Voltage:
3.7V
Dimensions:
Approximately 36(W) × 55(D)
× 14(H) mm (17⁄16"W × 23⁄16"D × 9⁄16"H)
Weight:
Approximately 46g (1.6oz)
Bundled Item:
Soft case
E-70
Warning Label
(on top side of
battery pack)
Attaching the Hand Belt (HA-F95HB)
To use the Hand Belt (HA-F95HB), attach it to the DT-X7 as follows.
Items Included
• Holdfast
• Hand Belt
• Screw (2pcs)
Attaching the Hand Belt
Attach the Hand Belt as described below.
1. Turn the DT-X7 over.
2. Attach the holdfast on the back of the DT-X7 and secure it using the screws supplied.
E-71
3. Thread the looped cord on the end of the Hand Belt through one of the strap holes at
the bottom of the DT-X7. (You can use either hole.)
Strap holes
4. Feed the belt through the wire loop on the mount, fold it back and secure it with the
hook-loop fastener.
Wire loop
Important!
• When inserting the DT-X7 with the Hand Belt attached into the USB Cradle, etc.,
check the Power LED on the cradle and the indicator on the DT-X7 to ensure that the
DT-X7 is inserted securely.
The DT-X7 must be inserted correctly to charge and communicate successfully.
E-72
CASIO COMPUTER CO., LTD.
6-2, Hon-machi 1-chome
Shibuya-ku, Tokyo 151-8543, Japan