Audiovox CDC-10R Owner`s manual

VOL
TUNE/
SKIP/
TRACK
VOL
CLAS
POP
ROCK
MP3 ST PTY ME/CR EON LOC
SW LOUD AF TA TP MONO REC
TAPE IN
CDP
P-945W
LEVEL METER
AM/FM/MPX RADIO WITH DETACHABLE FRONT PANEL,
COMPACT DISC PLAYER, CD CHANGER CONTROLS
AND QUARTZ CLOCK
OWNER'S
MANUAL
Released 3-27-02.
INDEX
Page
Operating Instructions ................................................................ 3 - 9
Specifications ............................................................................... 10
CD Changer Controls ................................................................... 11
Setting the Clock .......................................................................... 12
CD Player Error Codes ................................................................. 13
CD Changer Error Codes ............................................................. 13
Care and Maintenance ................................................................. 14
Warranty .......................................................................... Inside Back Cover
OPERATING INSTRUCTIONS
30
32
31
14
26
15
23
25
22
24
27
33
11
16
17
36
37
VOL
TUNE/
SKIP/
TRACK
VOL
9
CLAS
POP
ROCK
MP3 ST PTY ME/CR EON LOC
SW LOUD AF TA TP MONO REC
TAPE IN
CDP
LEVEL METER
2
18
3,4,5,6,7 8,10 12
21,38 19,39 20,40 29,35 28,34
1 POWER ON/OFF BUTTON
Press this button to turn the unit on or off. If the unit is off and the
ignition switch is "on", the unit will turn on automatically when a
disc is inserted, or when the MODE switch or BAND switch is
pressed.
2
1
13
AUDIO ADJUST VOLUME (VOL) CONTROL
3 AUDIO SELECT (SEL) BUTTON
This button is used to select the audio function (volume, bass,
treble, balance, or fade) to be adjusted using the Volume/Level
Control . Pressing the SEL button will select bass (BAS on
the display), treble (TRE), balance (BAL), fader (FAD) or volume (VOL). The display will automatically return to the normal
indication 5 seconds after the last adjustment or when another
function is activated.
2
To increase the volume level, press the VOL
button. The
volume will increase and the level will be shown on the display
panel from a minimum of VOL 00 to a maximum of VOL 100. To
BASS CONTROL
increase the volume quickly, keep the button pressed. To
decrease the volume level, press the VOL
button. Keep the To adjust the bass level, first select the Bass mode by pressing
so that the BAS indication appears on the
button pressed to decrease the volume quickly. The display the SEL button
will automatically return to the normal indication 5 seconds display panel. Within 5 seconds of choosing the Bass mode,
or
button
to adjust the
after the last volume adjustment or when another function is acti- press the AUDIO ADJUST VOL
vated. These buttons are also used in conjunction with the bass response as desired. The bass level will be shown on the
to adjust the bass, treble, bal- display panel from a minimum of -10 to a maximum of +10 (00
AUDIO SELECT (SEL) button
is flat response). The display will automatically return to the
ance, and fader levels as described in , ,
and .
-3-
4
3
3
456
7
2
normal indication 5 seconds after the last adjustment or when
another function is activated.
5 TREBLE CONTROL
To adjust the treble level, first select the Treble mode by pressing
the SEL button
so that the TRE indication appears on the
display panel. Within 5 seconds of choosing the Treble mode,
press the AUDIO ADJUST VOL
or
button
to adjust the
treble response as desired. The treble level will be shown on the
display panel from a minimum of -10 to a maximum of +10 (00 is
flat response). The display will automatically return to the
normal indication 5 seconds after the last adjustment or when
another function is activated.
3
2
6 LEFT/RIGHT BALANCE CONTROL
To adjust the left-right speaker balance, first select the Balance
mode by pressing the SEL button
so that the BAL indication
appears on the display panel. Within 5 seconds of choosing the
Balance mode, press the AUDIO ADJUST VOL
or
butto adjust the balance as desired. The balance position will
ton
be shown on the display panel from BAL10L (full left) through
BAL 10R (full right). When the volume level between the left and
right speakers is equal, BAL L=R will be shown on the display
panel. The display will automatically return to the normal indication 5 seconds after the last adjustment or when another function is activated.
3
2
7
FRONT/REAR FADER CONTROL
appears on the display panel. Within 5 seconds of choosing the
Fader mode, press the AUDIO ADJUST VOL
or
button
to adjust the front-rear speaker balance as desired. The fader
position will be shown on the display panel from FAD 10R (full
rear) through FAD 10F (full front). When the level between the
front and rear speakers is equal, FAD F=R will be shown on the
display panel. The display will automatically return to the
normal indication 5 seconds after the last adjustment or
when another function is activated.
2
8 LOUDNESS CONTOUR (LOUD)
When listening to music at low volume levels, this feature will
boost the bass and treble ranges to compensate for the characteristics of human hearing. Press and hold the BAND/LOUD
button for 2 seconds to activate this feature and the indication
LOUD ON will appear on the display panel. Pressing the button again for 2 seconds will deactivate the feature (the LOUD
OFF indication will disappear from the display panel).
9 AUDIO MUTE (MUTE)
This button is used to mute the volume from the system. By
pressing the button, a flashing MUTE indication will appear on
the display panel and the volume will be muted. Pressing the
MUTE button again, or activating the Volume Control
Select
(SEL) button , LOUD button or Equalizer (P.EQ) button will return the volume level to the setting in use before the Mute function was activated.
3
bl AM/FM BAND SELECTOR (BAND)
2
During radio operation, each momentary press of the BAND/LOUD
To adjust the front-rear speaker balance, first select the Fader button will change the radio band. The indication AM, FM1, FM2, or
mode by pressing the SEL button
so that the FAD indication
-4-
3
FM3 will appear on the display panel according to your selection.
cs
to return to disc play from the beginPress the Mode button
ning of the last track in play.
bm MANUAL
UP/DOWN TUNING (+
SEEK TUNING
/
-) / AUTOMATIC
The radio tuning function is normally in automatic seek tuning
mode. The radio will seek the next available station and stop at
that frequency. The Seek function can be stopped by pressing the
button again. The radio will return to the last tuned frequency.
To tune rapidly in an upward or downward direction, press and
hold either button. The radio will tune the entire band in an up or
down direction. When the desired radio frequency is reached,
release the button.
Pressing either button for 2.0 seconds will activate the manual
tuning function. MANUAL will appear on the display. Each time
the +
button is tapped, the radio will tune one frequency step
higher. Similarly, each tap of the
- button will tune one frequency step lower.
stop Pre-Set Scan operation and remain on the selected frequency. The station number (F) stops flashing.
Pressing the button for longer than 2 seconds will activate the
Auto-Store Tuning feature which will automatically scan the
band and enter up to 6 strong stations into the 6 pre-set memories. After entering the stations into the memories, the unit will
automatically stop at each station for 5 seconds so each can be
heard. If you have already set the pre-set memories to your favorite stations, activating the Auto-Store feature will erase those
stations and enter the new strong stations. This feature is most
useful when travelling in a new area where you are not familiar
with the local stations.
bo STATION PRE-SET MEMORIES
To set any of the 6 pre-set memories in each band, use the following procedure:
bn AUTO-STORE TUNING (AS) PRE-SET SCAN TUNING (PS)
During radio operation, press this button momentarily to scan the
6 stations pre-set into the memories of that band. The unit will
stop at each pre-set station for 5 seconds before continuing to the
next pre-set station. During this time, the pre-set station number
(F) in the band will flash. Press the button again momentarily to
-5-
1. Turn the radio on and select the desired band.
2. Select the first station to be pre-set using the Manual Up/
Down or Automatic Seek Tuning Controls .
bm
3. Press the pre-set button (1-6) to be set and continue to
hold it in. After approximately 2 seconds, a tone will sound
and the pre-set number will appear on the display panel,
indicating that the station is now set into that pre-set memory
position. The station can now be recalled at any time by
pressing that button.
4. Repeat the above procedure for the remain in pre-sets on
that band and for the other 4 bands on the unit.
button is pressed within one second. Similarly, with each momentary tap of the Backward Track Select button ( - ), the next
lower track number will be selected if the button is pressed within
one second.
bp LIQUID CRYSTAL DISPLAY PANEL FUNCTIONS
The Liquid Crystal Display (LCD) panel displays the frequency,
time, and all activated functions, including five bar graphs
which provide a visual representation of the audio signal.
bs CUE/REVIEW FUNCTIONS
NOTE: It is a characteristic of LCD panels that, if subjected to cold
temperatures for an extended period of time, they may
take longer to illuminate than under normal conditions. In
addition, the visibility of the numbers on the LCD may
slightly decrease. The LCD readout will return to normal
when the temperature increases to a normal range.
High-speed audible search to any section of the disc can be made
by the Cue and Review functions. Press and hold the Cue button (+ ) to advance rapidly in the forward direction or the Review button ( -) to advance rapidly in the backward direction.
During either function, the elapsed time within each track will automatically be shown on the display panel.
bq DISC SLOT
bt PAUSE (PAU) BUTTON
With the label surface facing up, gently insert the disc into the
slot until the soft-loading mechanism engages and disc play
begins. The
indication illuminates and becomes animated,
the CDP symbol lights, and the track number and elapsed time
will appear on the display panel.
Pressing this button during CD play will pause disc operation and
the elapsed time indication will remain stationary. Press the button again and disc play will resume.
bu REPEAT PLAY SELECTOR (RPT)
CAUTION: This unit is designed for play of standard 5" (12cm)
Compact Discs ONLY. Do not attempt to use 3" (8cm)
CD-Singles in this unit, either with or without an adaptor, as damage to the player and/or disc can occur. Such
damage will not be covered by the Warranty on this
product.
During disc play, press this button to repeat the play of the
selected track (RPT will appear on the display panel). Play of
the track will continue to repeat until the button is pressed again
and the RPT indication disappears from the display panel.
Repeat Play mode will also be cancelled by activating the Shuffle
Play
Track Scan
functions.
cl
br TRACK SELECT
These buttons are used to quickly select the beginning of a particular track. With each momentary tap of the Forward Track Select
button (+ ), the next higher track number will be selected if the
-6-
cm
cl SHUFFLE PLAY SELECTOR (SHF)
co TIME/FREQUENCY SELECTOR (T/F)
During disc play, press this button to play the tracks on the disc
in a random or shuffled order (SHF) will appear on the display
panel). In Random Play mode, pressing the Forward Track Select
(+ ) or the Backward Track Select ( -) will also select tracks in
a random order instead of the normal progression. Additional
presses will select tracks in random order. The Random Play
mode can be cancelled by pressing the button again (SHF)
indication will disappear from the display panel) or by activating
the Repeat Play
or Track Scan
functions.
bu
This unit can display the clock time, radio frequency or CD player
functions on the display panel. Pressing the Time/Frequency
Selector button when the radio frequency or CD player track
indication is shown will change the display to show the time.
The time display will automatically return to the radio frequency or
CD player function indication after 5 seconds.
cp FM MONO/STEREO SELECTOR (MONO)
cm
cm TRACK SCAN (SCN)
During FM radio operation, this button is used to select monaural
or stereo reception of the broadcast signal. Under normal reception conditions, the unit should be left in the stereo mode, as
indicated by ST on the display panel when listening to an FM
stereo signal. If the stereo signal is too weak for comfortable listening, press the button to switch to monaural reception (the ST
indication will disappear from the display panel and MONO will
appear). To return to the stereo reception mode, press the
button again so that the ST indication returns and the MONO
indication disappears.
During disc play, press this button to play the first 10 seconds of
each track on the disc (SCN will appear on the display panel).
When a desired track is reached, press the Scan button again
to cancel the function and play of the selected track will
continue. Track Scan mode will also be cancelled by activating
the Repeat Play
or Shuffle Play
functions.
bu
cn DISC EJECT (
cl
cq EQUALIZER SELECTOR (P.EQ)
)
Disc play is stopped, the disc is ejected and the unit will change to
radio operation by pressing this button.
The P.EQ button applies preset sound effects to the unit's audio output signal. The P. EQ button, when first pressed, causes
FLAT to appear on the panel, indicating no equalization factor. Subsequent presses will activate one of three operating modes (CLAS,
POP or ROCK). When the equalizer function is active, the bass
and treble levels can be changed by pressing the Select button
and the volume up/down buttons . The equalizer function
is disabled and the unit returns to the user-set bass and treble
levels.
If the disc is not removed from the disc slot within 15 seconds of
being ejected, it will automatically be re-loaded into the unit to
prevent it from being accidentally damaged. Play of the disc
to choose CD
can be resumed by using the MODE button
player function.
cs
3
-7-
2
dl
cr LOCAL/DISTANT (LOC) SELECTOR
This feature is used to select the strength of the signals at
which the radio will stop during Automatic Seek Tuning. Pressing and holding this button will select the Local setting (LOCAL will appear on the display panel) and only strong (local)
stations will be received. Pressing the button again will select
the normal Distant setting (Dx will appear on the display panel).
The radio will stop at a wider range of signals, including weaker
(more distant) stations.
cs MODE SELECTOR (MODE)
This button is used to select the radio, or the playback mode for the
CD player or remote CD changer (if installed). Each press of the
button will select a different mode as indicated on the display
panel.
During CD player operation, this button may be used to change
to radio or remote CD changer mode ("CDC AUX") without ejecting
the disc (the CDP indication will remain on the display panel to
show that a disc is still loaded in the unit). Press the button again to
return to integral CD player mode and resume play of the disc from
the point at which it was stopped.
ct & cu DISC SELECT (D.UP & D.DN)
This button is used to release the mechanism that holds the front
panel to the chassis. To detach the front panel, press the button
so that the left side of the panel is released. Grasp the released side
and pull it off of the chassis.
To re-attach the panel, position the right side of the panel in place
first and then press the left side of the panel in until the mechanism
locks it into place.
dm THEFT-DETERRENT LED
The theft-deterrent Light Emitting Diode (LED) is located behind the
front panel and is accessible when the front panel is removed. The
flashing light serves as a visual warning to the would-be thief that
the unit has been disabled by removal of the front panel.
dn RESET BUTTON
A RESET button is located on the front of the chassis (front panel
must be removed to access the button). The RESET circuitry is
provided to protect the microprocessor circuitry and should only
be activated under the following circumstances as it will erase the
time and pre-set memories:
1. Upon initial installation after all wiring is completed.
These buttons are used to increase or decrease selection of a
desired disc for play in the remote CD changer. To advance to a
higher number disc, press the D.UP button . To return to a
lower number disc, press the D.DN button . The number of the
disc in play will be shown on the display panel.
cu
FRONT PANEL RELEASE BUTTON
ct
-8-
2. After the position of the frequency step switch on the bottom
of the chassis has been changed.
3. If there is a malfunction of any of the switches on the unit,
pressing the RESET button may clear the system and return
to normal operation.
NOTES ON USE OF FRONT PANEL
DETACHING THE FRONT PANEL
1. Make sure the front panel is right-side-up when attaching it to the chassis as it cannot be attached when up-side down.
2. Do not press very hard on the front panel when attaching it to the chassis. No more than light to moderate pressure should be needed.
3. When attaching the front panel, make sure the right side is correctly
engaged before pressing the left side to lock it into position.
4. When taking the front panel with you, please use the supplied carrying
case to protect the panel from dirt and damage. Make sure there is no
dust or dirt on the electrical terminals on the back of the panel as this
could cause intermittent operation or other malfunctions.
Release Button
ATTACHING THE FRONT PANEL
Engage right
side first
NOTES ON USE OF REMOTE INPUT JACK
The remote input jack provides the user option of applying an external audio
source to the radio.
The audio jack is compatible with most "Walkman" CD and cassette
players, or an MP3 digital audio playback unit. When the external source
is connected, only that media is played by the radio; no other input sources
(radio or CD) are operative.
-9-
SPECIFICATIONS
Size:
7" W
x
2" H
178 mm x 50 mm
x
x
6-5/8" D
168mm
Operating Voltage:
12 volts DC, negative ground
Output Power:
160 watts maximum
(40 watts x 4 channels)
Output Wiring:
Floating-ground type designed for 4 speaker use.
Front and rear channels CANNOT be combined (bridged) for use
with 2 speakers.
RCA low-level outputs (rear channels).
Output Impedance:
Compatible with 4 ohm speakers.
Low-Level Output:
1.0 volt (1,000 mv.)
Tuning Range:
AM: 530 - 1,710 kHz. (10 kHz. step)
FM: 87.5 - 107.9 MHz. (200 kHz. step)
Sensitivity:
< 3.0 uV
FM Stereo Separation:
> 20 dB
CD Frequency Response:
20 - 20,000 Hz. +0 / -3 dB
CD Signal/Noise Ratio:
>60 dB
CD Channel Separation:
>55 dB
CD Distortion:
0.2%
*Specifications are subject to change without notice.
-10-
CD
CHANGER
dr TRACK SELECT (+
CONTROLS
Built into this radio are controls to operate an optional CD changer.
Please check with your Rampage/Audiovox car stereo specialist
or call 1-800-645-4994 for recommendations of the models that
will work with this radio.
Adjustment of the audio functions (volume, tone, balance, and
fader) for the CD changer operate in the same manner as they
do for radio play. The following controls will operate the CD
changer when it is installed and connected to this radio. Refer
to the owner’s manual included with the CD changer for instructions on the installation and correct loading and use of the CD
magazine.
do CD CHANGER MODE SELECTOR (MODE)
During radio or CD play, press this button to select operation of the
CD changer as shown by CDC on the display panel. Disc play will
begin and the disc and track number will be shown on the display
panel. If a new magazine has been loaded into the changer, play
will begin from the first track of the first disc in the magazine.
dp dq DISC SELECT (D.UP & D.DN)
&
These buttons are used to select the desired disc for play. To
advance to a higher number disc, press the D.UP button
To
return to a lower number disc, press the D.DN button . The
number of the disc in play will be shown on the display panel.
dp
dq
/
-)
The Track Select functions are used to quickly access the
beginning of a particular track. Each time the Forward Track
Select (+ ) in side of the button is pressed, the next higher
track number will be selected as shown on display panel. Similarly, each time the Backward Track Select (
-) side of the
button is pressed, the next lower track number will be selected
as shown on the display panel.
ds CUE/REVIEW FUNCTIONS (+
/
-)
High-speed audible search to any section of the disc can be made
by the Cue and Review functions. Press and hold the Cue (+ )
side of the button to advance rapidly in the forward direction (the
disc play symbol will rotate forward on the display panel) or the
Review ( -) side of the button to advance rapidly in the backward
direction (the disc symbol will rotate backwards on the display
panel).
dt TRACK/DISC SCAN SELECTOR (SCN)
When the SCN button is pressed, the SCN indication will appear
on the display panel, and the first 10 seconds of each track on
the disc will be played in order. When a desired track is reached,
press the SCN button once and play of the selected track will
continue (SCN will disappear from the display panel). The Track
Scan mode will also be canceled by activating the (Repeat or
Random Play functions).
When the SCN button is pressed and held, the DSN indication will appear on the display panel and the first 10 seconds of
the first track on each disc in the magazine will be played. When
-11-
a desired disc is reached, press the Scan button again and play
of the selected disc will continue ( DSN will disappear from the
display panel). The Disc Scan mode will also be canceled by
activating the (Repeat Play or Random Play functions).
du DISC/TRACK REPEAT PLAY (RPT)
When the Repeat button is pressed, the RPT indication will
appear on the display panel and play of the selected track will
be continually repeated until the Track Repeat mode is canceled
by pressing the Repeat button again or by activating the Scan or
Shuffle Play functions.
When the Repeat button is pressed and held, the DRT indication will appear on the display panel and play of the selected
disc will be continually repeated until the Disc Repeat mode is
canceled by pressing the Repeat button again or by activating
the Scan
or Shuffle Play
functions.
dt
el
dt
el
SETTING
1. Turn the vehicle ignition and radio “on”.
2. Press the Time/Frequency Selector button
el DISC/TRACK SHUFFLE PLAY (SHF)
When the SHF button is pressed, the SHF indication will appear
on the display panel and the tracks on the disc will be played in a
random, shuffled order. The Track Select button
will also select tracks in the shuffled order instead of the normal progression. The Random Track mode can be canceled by pressing
the Shuffle button again or by activating the Scan
or Repeat
functions.
Play
When the SHF button is pressed and held, the DSF indication
will appear on the display panel and the discs in the magazine will
be played in a random, shuffled order, as well as the tracks on
each disc. After playing a track selected at random from a disc in
the magazine, the unit will select another disc at random and
play a randomly selected track on it. This will continue until
the Random Disc mode is canceled by pressing the Shuffle button again or by activating the Scan
or Repeat Play
functions.
THE
co to display the time.
dr
dt
du
dt
du
CLOCK
co
3. While the time is being displayed, press the Time /Frequency Selector button
again. The time display will flash and a tone will
sound. Press the Manual Up Tuning button (
+ ) to adjust the hours or the Manual Down Tuning button ( ) to adjust the
minutes to the correct time.
4. Five seconds after the last hour or minute adjustment is made, the time will be set in the unit and normal operation can resume.
-12-
OR CODES
CD PL A YER ERR
ERROR
If a problem should develop while operating the CD player, an error code (ER-1, ER-2, ER-3, etc.) may appear on the display panel.
This can indicate a number of problems with the unit, including a mechanical error or an error in the microprocessor control of the
player. If an error code should appear, try ejecting and re-loading the disc into the player. While the disc is out of the unit, make sure
it is clean, undamaged, and loaded correctly (label surface up). You may also try activating the RESET button on the unit, but this
will also erase the time and pre-set memories.
If the suggested measures do not solve the problem, contact an approved warranty station near you for further assistance.
dn
CD
CHANGER
ERROR
CODES
If a problem should develop while operating the CD changer, the following error codes may appear on the display panel.
ER-1: Indicates that there is no magazine loaded in the CD changer.
ER-2: Indicates a problem with the magazine eject function.
ER-3: Indicates an error in the disc loading function.
ER-4: Indicates an error in the disc un-loading function.
ER-5: Indicates an error in the magazine position.
ER-6: Indicates an error in the laser pick-up position.
ER-7: Indicates an error in the laser focus on the disc.
In any of the above situations, try ejecting the CD magazine from the changer and make sure the discs are clean, undamaged, and
loaded correctly (refer to the Owner’s Manual of the CD changer). Re-load the magazine and check for proper operation. You may
also try activating the RESET button on the unit, but this will also erase the time and pre-set memories.
dn
If the suggested measures do not solve the problem, contact an approved warranty station near you for further assistance.
-13-
l
Do not attempt to open the unit chassis. There are no user
serviceable parts or adjustments inside.
l When the vehicle warms up during cold weather or under damp
conditions, moisture may condense on the lens of the disc
player. Should this occur, the player will not operate properly
until the moisture has evaporated.
l The unit is designed with a vibration dampening CD mechanism
to minimize interruption of disc play due to normal vibration in
a moving vehicle. When driving on very rough roads, however,
occasional sound skips may occur. This will not scratch or
damage the disc and normal play will resume when the rough
conditions cease.
CARE AND MAINTENANCE
The radio section of your new sound system does not require any
maintenance. We recommend you keep this manual for
reference on the many features found in this unit as well as how
to set the clock.
The compact disc player section also requires no routine
maintenance, but proper understanding of its use and handling
will help you obtain maximum enjoyment of its capabilities. The
following points should be observed:
l When cleaning the interior of the vehicle, do not get water or
cleaning fluids on the unit.
l The CD player is a precision instrument and will not operate
properly in extreme hot or cold. In case of such conditions, wait
until the interior temperature of the vehicle reaches a normal
temperature before using the player.
l If the temperature inside the player gets too hot, a protective
circuit will automatically stop play of the disc. In this case, allow
the unit to cool off before operating the player again.
l Never insert anything other than a 5" (12 cm) compact disc into
the player as the mechanism can be damaged by foreign
objects.
l Do not attempt to use 3" (8 cm) CD-Single discs in this unit,
either with or without an adaptor, as damage to the player and/
or disc may occur. Such damage will not be covered by the
Warranty on this product.
l When not using the disc player, always remove the compact
disc. Do not leave an ejected disc sitting in the disc slot as this
can expose it to sunlight and other causes of damage.
HANDLING COMPACT DISCS
Dirt, dust, scratches, and warpage can cause skips in the
playback and deterioration of sound quality. Please follow these
guidelines to take care of your compact discs:
-14-
l
l
l
l
l
l
Use only compact discs with the mark
.
Fingerprints, dust, and dirt should be carefully wiped off the
disc’s playing surface (shiny side) with a soft cloth. Wipe in a
straight motion from the inside to the outside of the disc.
Never use chemicals such as record sprays, household cleaners
or thinner to clean compact discs. Such chemicals can
irreparably damage the disc’s surface.
Discs should be kept in their storage cases when not in use.
Do not expose discs to direct sunlight, high temperatures or
high humidity for extended periods.
Do not stick paper, tape, or labels on the disc surfaces nor write
on them with any type of marker.
12 / 24 MONTH LIMITED WARRANTY
Applies to automotive radios, radio/tape players, radio/CD
players, CD changers, power amplifiers, equalizers and accessories.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof,
under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such
defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill
of sale), specification of defect(s), transportation prepaid, to an approved warranty station or the Company at the address shown below.
The warranty period will be extended to 24 months from the date of original purchase if the product is installed by an authorized Prestige Audio
dealer. To claim warranty service during this extended period, the bill of sale must specify that the product was installed by an authorized Prestige
Audio dealer.
This Warranty does not extend to the elimination of externally generated static or noise, to correction of antenna problems, to costs incurred for
installation, removal or reinstallation of the product, or to damage to tapes, compact discs, speakers, accessories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through
alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code
label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT
PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER
FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF
30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or
representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage
so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
U.S.A. : AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 l 1-800-645-4994
CANADA : CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
128-5543
© 2002 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788
Printed in China
128-6289