- Home
- Home security & automation
- Security access control systems
- BEST ACCESS SYSTEMS
- 45HM IDH Max 1300
- Specification
advertisement
IDH MAX
®
&
ELECTROMECHANICAL LOCKS
2
TABLE OF CONTENTS
IDH MAX ®
Page introduction ....................................................2
IDH MAX ®
IDH Max ® features ..........................................................2
and IDH Max ® 1300 comparison chart ............3
HM, KM, HW & KW options ............................................3
40HM IDH MAX ® specifications, how-to-order ................4
40HM IDH MAX ®
93KM IDH MAX ® functions ..............................................5
specifications........................................6
93KM IDH MAX ®
93KM IDH MAX ® how-to-order ........................................6
functions ..............................................7
40HW electrified specification ..........................................7
40HW electrified how-to-order ........................................8
Page
40HW electrified functions ..............................................8-9
8KW/9KW electrified specification ....................................10
8KW/9KW electrified how-to-order ..................................10
8KW/9KW electrified functions ........................................10
Trim variations ..................................................................11
Electrified accessories ................................................12,13
Terminology ......................................................................13
1W electric switch lock introduction ..................................14
Optional boxes ..................................................................14
1W electric switch lock how-to-order ................................14
1W electric switch locks................................................15-19
IDH MAX ® – INTRODUCTION
The IIDH MAX ® from Stanley Security Solutions offers convenience and efficiency for your electrified lock applications. Instead of installing reader devices, installing electrified strikes, installing door contacts and installing request-to-exit devices, you can now install the IDH MAX ® in cylindrical or mortise lock applications. With IDH MAX ® all of the formerly separate equipment needed to control access are self-contained in a single installation. The complexity of multiple wire runs is drastically reduced.
You can let Stanley Security Solutions show you how to MAXimize your access control system with the IDH MAX ® ! For the name and location of your local office, visit our web site at www.stanleysecuritysolutions.com. IDH MAX ® and W series locks (with the exception of the IDH Max ® 1300) are compatible with Stanley’s NT500 and B.A.S.I.S. Acess Control Systems.
IDH MAX ® – FEATURES
IDH Max
®
Features
• Includes latch and door position indicator, RQE switch.
• The 1300 option eliminates the need for a RIM (reader interface module) which is embedded behind the escutcheon
• Requires only one 4 conductor wire run
• Reduces number of components installed and visible at the door (PIR, RQE push buttons and door contacts)
• Installation time is reduced
• The RQE switch senses the inside lever/knob rotation.
• All of the door components are housed in one manufacturer's hardware
• With the elimination of components, only the lockset is visible at the door
• The reader is integrated into the lockset escutcheon
• Available in magnetic stripe and proximity readers
• Available in all popular lever/knob styles and finishes
• Operates with BEST interchangeable core as a mechanical override
• Integrates with many manufacturer's on-line EAC equipment
Mortise Features
(continued)
• Twist off lever spindle design protect internal lock parts from damage and failure.
• Oil impregnated stainless steel 3 /
4
" anti-friction latchbolt reduces door closing force and wear.
Cylindrical Features
• Non-handed levers allow for ease of installation
• Lock chassis meets the requirements as listed in the ANSI/
BHMA A156.2, standard for Series 4000 Grade 1 locks
• UL listed for GYQS Electrically controlled single point licks or latches for use on 3 hr, A label single doors (4 ' x 10 ' ) GYJB.
The listing applies for both U.S. and Canadian applications
• Request-to-exit sensor positioned inside lock trim
• The ISC (Intelligent System Controller) is embedded behind the escutcheon secured and out of site
• Request-to-exit and door contact sensors are standard in
IDH MAX cylindrical locks
Mortise Features
• Lock case meets the requirements as listed in the ANSI/
BHMA A156.13 standard for Series 1000, Grade 1
Operational and Grade 2 Security locks
• UL listed for GYQS Electrically controlled single point locks or latches for use on 3 hr, A label doors (4 ' x 10 ' ). The listing applies for bother U.S. and Canadian applications
• Door contact, request-to-exit, and latch status sensors positioned inside lock case
• The 1300 option eliminates the need for a RIM (reader interface module) which is embedded behind the escutcheon
• The door contact magnet is installed behind the strike and out of site (except when deadbolt option is ordered)
• All sensors are all standard in IDH Max mortise locks
• The heavy duty design of the mortise lock makes easy field maintenance and reduces risk of part failure
Magnetic Stripe Electronic Lock Features
• Durable material has teflon-like characteristics for increased life and wear resistance
• Variable read rate allows for easy usage
Proximity Card Reader Features
• HID and Motorola/Indala proximity cards supported
• UL listed for GYQS Electrically controlled single point locks or latches.
• Usable in all environmental/exterior applications.
1300 Option Features
• Eliminates need for small panel interface module
• Eliminates reader interface board
• Incorporates 3 modules into a single electronics board inside
IDH Max escutcheon trim
• Connects directly to ACP via 2 wire RS485 connection
I D H M A X ® & E L E C T R O
IDH MAX ®
*
& IDH MAX ® 1300 COMPARISON CHART
**
IDH MAX ®
1. Prep door for IDH MAX ®
2. Run single 4 conductor wire for IDH MAX ®
3. Install IDH MAX ®
4. Install electrified hinge
5. Mount control panel
* Operates with any control panel hardware, including B.A.S.I.S.
control panels.
IDH MAX ® 1300
1. Prep door for IDH MAX ®
2. Run single 4 conductor wire for IDH MAX ®
3. Install IDH MAX ®
1300
1300 which includes Intelligent System
4. Install electrified hinge
** Operates with B.A.S.I.S. control panels only.
HM, KM, HW & KW – OPTIONS
AL– Besides complying with a wide variety of accessibility codes and ordinances, lever handles are available with a special abrasive feature. Abrasive strip on the lever immediately identifies warnings on doors to hazardous areas for the blind.
BRK– When excessive force (approx. 300 inch lbs.) is applied to #4, #6 keyed knobs, they “breakaway” and spin freely, thus allowing entrance only by key. Simple part replacement returns lock to functional usage.
IDH– The integrated Door Hardware groups three components into one hardware package. 1. Door monitoring switch (normally closed) 2. Request-to-Exit switch (normally open) 3. Electrically controlled locking mechanism.
KNL– Knurl feature is available only on #6 knobs. The knurling is machined into the outer edge of the knob. The knurled feature can be used for blind, safety, or accessibility applications.
LL– Lead lined feature can be used to protect against X-rays. Since the majority of lead lined doors contain the lead in the surface of the door, the knob lockset provide lead lining for the holes cut in the door when preparing the door for the trim.
LM– The Lost Motion feature allows the lever handle to move 45 degrees from parallel to the horizontal plane without engaging the latchbolt assembly. When the lockset is in the locked mode, this feature makes over-torque or over-lever-age abuse more difficult to achieve.
SH– Security head provided for all exposed screws.
RQE– Cylindrical or Mortise locksets can be supplied with a request-to-exit switch. A normally open switch provides momentary switch closure when the inside lever/knob is rotated.
TAC– Grooves are machined into knobs to improve grip or to be used as a warning in hazardous areas. This option can be used for blind, safety or accessibility applications.
Thick door– Specify thickness if other than 1 3 ⁄
4
" .
TL– Tactile levers may be used in areas where improved grip is required or as a warning in hazardous or Safety First areas. Grooves are machined into the back of the hand grasp portion of the lever to improve grip and/or provide a sensory warning. This option can be used for blind, safety, or accessibility applications.
1300– Integrated BAS1300/LNL1300 reader electronics board or (ISC) Intelligent System Controller is embedded behind the escutcheon secured and out of site. Functions with B.A.S.I.S./Mercury on-line equipment only.
OMECHANICAL LOCKS
3
4
40HM IDH MAX ® – SPECIFICATIONS
MECHANICAL
Case— Heavy wrought steel, 5 7 ⁄
8
" H x 4 1 ⁄
4
" D x 1 " W steel parts are zinc dichromate plated for corrosion protection.
Faceplate— Brass or bronze, 1 to beveled 1 ⁄
8
" - 2 " .
1 ⁄
4
" x 8 " x 7 ⁄
32
" . Armored. Adjustable from flat
Strike— Brass, bronze or Stainless Steel, 4 7 ⁄
8
" x 1 1 ⁄
4
" x 3 ⁄
32
" . Fits standard door frame cut out as specified in ANSI A115.1.Correct strike automatically supplied with unit. Strike box supplied standard.
Door thickness— For doors 1 3 ⁄
4
" – 4 " thick.
Installation— Lock requires modified door prep to mount the trim. Faceplate dimensions fit standard door preparation as specified in ANSI A115.1,.
Lockset is reversible for hand of door.
Latchbolt— Stainless steel, 3 ⁄
4
" throw with anti-friction latch.
Deadbolt— Solid stainless steel, 1 " throw.
Auxiliary bolt— Stainless steel.
Die cast trim housing—Dimensions: 10
Knobs— Diameter: 2 1
3 ⁄
8
" H x 3 1 ⁄
4
" W x 1 " D sloping down to 3 ⁄
4
" .
⁄
8
" Projection on door: 2 7 ⁄
8
"
#4, #6 knobs: Material machined from brass or bronze.
Lever handle— Brass, bronze or stainless steel. (Lever #3, #14 and #15 conform to California Titles 19 and 24.)
Mounting— Knob and lever attached with hardened set screw on inside knob or inside lever.
45HM IDH MAX ® Mortise
Finish— 605-bright brass, clear coated; 606-satin brass, clear coated; 611-bright bronze, clear coated; 612-satin bronze, clear coated; 613-oxidized satin bronze, oil rubbed; 625-bright chromium plated; 626-satin chromium plated; 629-bright stainless steel; 630-satin stainless steel; 690-dark bronze.
ELECTRONIC
Maximum current draw: 1.1 Amp for 50 milliseconds
Typical current draw (hold condition): 650 milliAmps
Voltage: 10.2 to 13.2 V (DC only)
Operating Temperature: Minimum/Maximum range Inside: 70˚± 4˚F (21˚± 2˚C) Outside: -31˚F (-35˚C) to +151˚F (+66˚C)
Magnetic Stripe Card Reader:
Read Rate: 5 inches per second to 50 inches per second.
Card thickness: ISO standard .030
"
± .003 thick.
Compliance to FCC, Canadian, and European EMC requirements; for interference FCC Class A digital apparatus.
Magnetic Stripe adaptation: Trim option that can accept other manufacturers cylinder.
Proximity Reader:
ANSI/BHMA A156.25 compliant. Compatible with Motorola / Indala and HID proximity cards. ABA and Wiegand output.
Weatherproof bezel and gasket provide protection for outdoor use. (Usable in all environmental/exterior applications)
Card Read Range: 0 – 3 inches. Compliance to US FCC, Canadian FCC, and European EMC requirements
ESD Protection:15 Kilo Volt
40HM IDH MAX ®
–
HOW TO ORDER
45HM
Series
7
Core
Housing
DEU
Function
14
Lever/Knob
Style
MS
Trim
Style
626
Finishes
†
45HM–
IDH Max™
0– Keyless or less cylinder,
7– 7 pin housing
ONLY
DEL– electrically locked
DEU– electrically unlocked
NXEL– electrically locked
NEU– electrically unlocked
TDEL– electrically locked
TDEU– electrically unlocked
LEL– electrically locked
LEU– electrically unlocked
(page 5)
Levers
3– solid tube return
12– solid tube
14– curved return
15– curved angle return
16– curved no return
17– gullwing no return
Knobs
4– round
(page 11)
MS– magnetic stripe
PM– proximity
Motorola
PH– proximity
HID
MSA– other cylinder
PHA– other cylinder
PMA– other cylinder
(page 11)
605
611
613
619
626
606
612
618
625
690
**Must specify key mark and number of keys or designate L/C for less core. †See H Series catalog for details.
RH
Handing
RH
RHRB
LH
LHRB
KNL
Options†
SH – security head screws
TAC – tactile lever
Thick
Door – specify thickness if other than 1 3 /
4
"
7/8" LTC– flat lip strike
1300 – B.A.S.I.S. direct connect
(page 3)
I D H M A X ® & E L E C T R O
Function
DEL–Locked
Fail Safe
Latch
Operated by
• Outside knob/lever when power is removed from the solenoid
• Outside key
• Inside knob/lever.
Locked by
40HM IDH MAX ®
Outside Knob/Lever
Applying power to solenoid; remains locked while power is on.
Unlocked by
Removing power from solenoid
– FUNCTIONS
Inside Knob/Lever
Locked by Unlocked by
Cannot be locked Always unlocked
DEU–Unlocked
Fail Secure
Powered by 12 DC. temperature control module is not needed.
• Outside knob/lever when power is removed from the solenoid
• Outside key
• Inside knob/lever.
Removing power from solenoid
Applying power to solenoid; remains locked while power is on.
Cannot be locked Always unlocked
NXEL–Locked
Fail Safe
NXEU–Unlocked
Fail Secure
TDEL–Locked
Fail Safe
TDEU–Unlocked
Fail Secure
LEL–Locked
Fail Safe
LEU–Unlocked
Fail Secure
Powered by 12 DC. temperature control module is not needed.
• Outside knob/lever when power is removed from the solenoid
• Inside knob/lever.
Applying power to solenoid; remains locked while power is continuously applied.
Removing power from solenoid
Latchbolt is deadlocked by an auxiliary latch
Powered by 12 DC. temperature control module is not needed.
• Outside knob/lever when power is removed from the solenoid
• Inside knob/lever.
Removing power from solenoid
Applying power to solenoid; remains locked while power is continuously applied.
Latchbolt is deadlocked by an auxiliary latch
Powered by 12 DC. temperature control module is not needed.
• Outside key
• Outside knob/lever when power is removed from the solenoid.
Latchbolt is deadlocked by an auxiliary latch
Applying power to the solenoid; remains locked while power is continuously applied
Deadbolt operated by:
Outside key
Removing power from the solenoid
Deadbolt and Latchbolt retracted simultaneously by:
• Inside knob/lever
• Outside knob/lever when power is removed
Powered by 12 DC. temperature control module is not needed.
• Outside key
• Outside knob/lever when power is removed from the solenoid.
Latchbolt is deadlocked by an auxiliary latch
Removing power from the solenoid
Deadbolt operated by:
Outside key
Applying power to the solenoid; remains locked while power is continuously applied
Deadbolt and Latchbolt retracted simultaneously by:
• Inside knob/lever
• Outside knob/lever when power is removed
Powered by 12 DC. temperature control module is not needed.
• Outside knob/lever when power is removed from the solenoid
• Inside knob/lever.
Applying power to the solenoid; remains locked while power is continuously applied
Deadbolt extended by:
Inside thumb turn
Removing power from the solenoid
Deadbolt retracted by:
• Inside thumb turn
• Inside knob/lever retracts the deadbolt and latchbolt simultaneously
• Outside lever when power is removed
Powered by 12 DC. temperature control module is not needed.
• Outside knob/lever when power is applied to the solenoid
• Inside knob/lever.
Removing power from the solenoid
Deadbolt extended by:
Inside thumb turn
Applying power to the solenoid; remains locked while power is continuously applied
Deadbolt retracted by:
• Inside thumb turn
• Inside knob/lever retracts the deadbolt and latchbolt simultaneously
• Outside knob/lever when power is removed
Powered by 12 DC. temperature control module is not needed.
Cannot be locked
Cannot be locked
Cannot be locked
Cannot be locked
Cannot be locked
Cannot be locked
OMECHANICAL LOCKS
Always unlocked
Always unlocked
Always unlocked
Always unlocked
Always unlocked
Always unlocked
5
6
9KM IDH MAX ®
MECHANICAL
– SPECIFICATIONS
Materials— Internal parts are brass, zinc or corrosion-treated steel.
Chassis— 2 1 ⁄
16
" diameter to fit 2 1 ⁄
8
" diameter hole in door.
Strike— Brass or bronze, 4 7 ⁄
8
" x 1 1 ⁄
4
" x 3 ⁄
32
". Fits standard door frame cut out as specified in ANSI A115.1. Correct strike automatically supplied with unit.
Strike box supplied standard.
Backset— 2 3 ⁄
4
" standard, 3 3 ⁄
4
" and 5" available.
Door thickness— For doors 1 3 ⁄
4
" – 2 1 ⁄
4
"
Installation— Lock dimensions requires modified door prep ANSI A156.2
Series 4000, Grade 1 to mount housing.
Latchbolt— 9 ⁄
16
" throw.
Die cast trim housing— Dimensions: 10 3 ⁄
8
" H x 3 1 ⁄
4
" W x 1" D sloping down to
Knobs— Diameter: 2 1 ⁄
8
" Projection on door: 2 7 ⁄
8
"
3 ⁄
4
".
#4, #6 knobs: Material machined from brass or bronze.
Lever handle— Made from high-quality zinc alloy. Body is approximately 1 5 ⁄
8
" in diameter: Handle is approximately 4 3 ⁄
4
" in length (from center-line of chassis).
(Lever #14,15 conform to California Titles 19 and 24.)
Finish— 605-bright brass, clear coated; 606-satin brass, clear coated; 611-bright bronze, clear coated; 612-satin bronze, clear coated; 613-oxidized satin bronze, oil rubbed
625-bright chromium plated; 626-satin chromium plated; 690-dark bronze.
93KM IDH MAX ®
ELECTRONIC
Maximum current draw: 850 MilliAmps, for 50 milliseconds
Typical current draw (hold condition): 550 milliAmps
Voltage: 10.2 to 13.2 V
Operating Temperature:
Minimum/Maximum range Inside: 70˚± 4˚F (21˚± 2˚C) Outside: -31˚F (-35˚C) to +151˚F (+66˚C)
Cylindrical
Magnetic Stripe Card Reader:
Read Rate: 5 inches per second to 50 inches per second.
Card thickness: ISO standard .030" ± .003 thick. Compliance to FCC, Canadian, and European EMC requirements; for interference FCC Class A digital apparatus.
Magnetic Stripe adaptation: Trim option that can accept other manufacturers cylinder.
Proximity Reader:
ANSI/BHMA A156.25 compliant, Compatible with Motorola / Indala and HID proximity cards, ABA and Wiegand output
Weatherproof bezel and gasket provide protection for outdoor use. (Usable in all environmental/exterior applications).
Card Read Range: 0 – 3 inches. Compliance to US FCC, Canadian FCC, and European EMC requirements
ESD Protection: 15 Kilo Volt
9KM/8KM IDH MAX ® – HOW TO ORDER
93KM 7 DDEU 14 MS STK
Series Core
Housing
Function Lever*/Knob
Style
Trim*
Style
Strike
Package
Lever
93KM– 2 3 /
4
"
94KM– 3 3 /
4
"
95KM– 5"
Knob
83KM– 2 3 /
4
"
84KM– 3 3 /
4
"
85KM– 5"
0– keyless
7– 7 pin housing accepts all BEST cores
DDEU– electricallyunlocked
DDEL– electricallylocked
(page 7)
Lever
14– curved return
15– contour angle return
16– curved no return
Knob
4– round
6– tulip
(page 11)
MS– magnetic stripe
PM– proximity
Motorola
PH– proximity
HID
(page 11)
STK– 2 3 /
4
"
ANSI
S3– 4 7 /
8
"
ANSI
626
Finishes*
605 606
611 612
613 618
619 625
626 690
TL
Options
8KM:
BRK – breakaway knob
KNL – knurled knob
TAC – tactile knob
9KM:
AL – abrasive lever
LM – lost motion
TL – tactile lever
Note: specify inside (I), outside
(O), or both (B) for AL, TL,TAC,
KNL options
Both 8KM & 9KM:
SH – security head screws
3
/
4 –
3
/
4
" throw latch
1300 – Integrated BAS1300/
LNL1300 reader electronic board
(page 3)
* Handles and trim are made from a zinc alloy, and have been plated to be equivalent in appearance to the finishes listed.
IDH MAX ® & ELECTROMECHANICAL LOCKS
Function Latch
Operated by
DDEL–Locked • Rotating the inside knob/lever, OR
• Rotating the outside knob/lever—only when power is off, OR
• Turning the key in the out side knob/lever.
9KM IDH MAX ®
Outside Knob or Lever
Locked by Unlocked by
– FUNCTIONS
Inside Knob or Lever
Locked by Unlocked by
Switching off 12 volts DC Cannot be locked Always unlocked Applying 12 volts DC.
The outside knob/lever remains locked only while power is on.
Powered by 12 DC. temperature control module is not needed.
DDEU–Unlocked • Rotating the inside knob/lever, OR
• Rotating the outside knob/lever—only when power is on, OR
• Turning the key in the out side knob/lever.
Switching off 12 volts DC Applying 12 volts DC.
The outside knob/lever remains locked only while power is off.
Powered by 12 DC. temperature control module is not needed.
Cannot be locked Always unlocked
Shading indicates a ridged lever/knob in a non-energized state.
40HW ELECTRIFIED – SPECIFICATIONS
The 40HW electromechanical locks provide a way to lock or unlock a door from a remote location for safety, convenience, or security. The 8KW/9KW cylindrical and
40HW mortise locks in fail-safe or fail-secure operation. These locksets can be controlled by an individual switch, switch lock, relay, access control or other automatic control system. As expected, the 8KW/9KW and 40HW electromechanical locks exhibit the same features and meet the same specifications as our standard 8K/9K cylindrical and 40H mortise locksets.
Types:
• 12 volts AC or DC — 1.10 amps
• 24 volts AC or DC — 0.75 amps
• All EU functions: Electrically Unlocked (Fail Secure)
• All EL functions: Electrically Locked (Fail Safe)
Approval Listings:
• UL listed for GYQS Electrically-controlled singlepoint locks or latches.
• This product has been approved by the California State Fire Marshal (CSFM) pursuant to section 13144.1 of the California Health and Safety Code.
• Approved by the city of New York Board of Standards and Appeals under calendar number 49-88-SA. See CSFM listing No. 4136-1175:101 for allowable values and/or conditions fo use concerning material presented in this document. It is subject to re-examination,revisions and possible cancellation.
NOTE: A Temperature Control Module (TCM) may be needed when a lockset is energized for long periods of time. The TCM must be ordered separately for
"EU" functions, but is automatically included with 45HW "EL" functions.
40HW Mortise Electrically-
Operated Lockset
OMECHANICAL LOCKS
7
8
40HW ELECTRIFIED – HOW TO ORDER
45HW
Series
7
Core
Housing
NXEU
Function
12
Lever
Style
J
Trim
Style
612
Finishes
†
LH
Handing
45HW– lever
47HW– lever high security
45HW:
0– keyless or less cylinder,
7– 7 pin
47HW:
7– 7 pin
(accepts
5C cores only)
45HW/47HW:
DEL– single key latch, fail safe
DEU– single key latch, fail secure
WEL– double key latch, fail safe
WEU– double key latch, fail secure
TDEL– single key deadbolt, fail safe
TDEU– single key deadbolt, fail secure
TWEL– double key deadbolt, fail safe
TWEU–double key deadbolt, fail secure
Levers:
3– solid tube/ return
12– solid tube/ no return
14– curved return
15– contour/ angle return
16– curved/no return
17– gullwing no
4– round return
Knobs:
45HW:
H– 2 9 /
16
" dia.
J– wrought
M– forged
N– forged concealed cylinder
S– 3 1 /
2
" dia.
47HW:
M– forged
45HW:
605 606
611 612
613 618
619
626
47HW:
626
625
690
630
RH
RHRB
LH
LHRB
45HW only:
NXEL– keyless, latch, fail safe
NXEU– keyless, latch, fail secure
LEL– keyless, deadbolt, fail safe
LEU– keyless, deadbolt, fail secure
(pages 8–9) (page 11) (page 11)
* “N” trim not available on double keyed functions. **Must specify key mark and number of keys or designate L/C for less core.
†See H Series catalog for details.
40HW ELECTRIFIED – FUNCTIONS
Function Latch
Operated by
Outside Knob or Lever
Locked by Unlocked by
DEL–Locked
Fail Safe
• Outside knob/lever when power is removed from the solenoid
• Outside key
• Inside knob/lever.
Applying power to solenoid; remains locked while power is on.
Removing power from solenoid
RQE
Options†
AL – abrasive lever
IDH – integrated door hardware
LL – lead lined
LS – latch status
RQE – request to exit
SH – security head screws
TL – tactile lever
Thick
Door – specify thickness if other than 1
3
/
4
"
(page 3)
Inside Knob or Lever
Locked by Unlocked by
Cannot be locked Always unlocked
DEU–Unlocked
Fail Secure
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty. Temperature control module (TCM) included.
• Outside knob/lever when power is removed from the solenoid
• Outside key
• Inside knob/lever.
Removing power from solenoid
Applying power to solenoid; remains locked while power is on.
Cannot be locked Always unlocked
WEL–Locked
Fail Safe
WEU–Unlocked
Fail Secure
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty.
• Inside and Outside knob/lever when power is removed from the solenoid
• Inside/Outside key
Latchbolt is deadlocked by an auxiliary latch
Applying power to solenoid; remains locked while power is continuously applied.
Removing power from solenoid Applying power to the solenoid; remains locked while power is continuously applied
Removing power from the solenoid
Temperature control module (TCM) included.
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty. Applying voltage locks inside & outside knobs/levers simultaneously.
• Inside and Outside knob/lever when power is applied to the solenoid
• Inside/Outside key
Latchbolt is deadlocked by an auxiliary latch
Removing power from solenoid
Applying power to solenoid; remains locked while power is continuously applied
Switching off 24 volts AC/DC. Inside knob/lever remains locked only while power is off.
Applying 24 volts
AC/DC. Inside knob/lever remains unlocked only while power is on.
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty. Applying voltage locks inside & outside knobs/levers simultaneously.
IDH MAX ® & ELECTROMECHANICAL LOCKS
Function
TDEL–Locked
Fail Safe
TDEU–Unlocked
Fail Secure
TWEL–Locked
Fail Safe
TWEU–Unlocked
Fail Secure
NXEL–Locked
Fail Safe
NXEU–Unlocked
Fail Secure
LEL–Locked
Fail Safe
LEU–Unlocked
Fail Secure
Latch
Operated by
40HW ELECTRIFIED – FUNCTIONS (CONTINUED)
Outside Knob or Lever
Locked by Unlocked by
Inside Knob or Lever
Locked by Unlocked by
• Outside key
• Outside knob/lever when power is removed from the solenoid.
Latchbolt is deadlocked by an auxiliary latch
Applying power to solenoid; remains locked while power is continuously applied.
Deadbolt operated by:
Outside key
Removing power from solenoid
Deadbolt and latchbolt retracted simultaneously by:
• Inside knob/lever
• Outside knob/lever when power is removed.
Cannot be locked Always unlocked
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty. Temperature control module (TCM) included.
• Outside key
• Outside knob/lever when power is applied to the solenoid.
Latchbolt is deadlocked by an auxiliary latch
Removing power from solenoid
Deadbolt operated by:
Outside key
Applying power to solenoid; remains locked while power is continuously applied.
Deadbolt and latchbolt retracted simultaneously by:
• Inside knob/lever
• Outside knob/lever when power is removed.
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty.
Cannot be locked Always unlocked
• Outside & inside key
• Outside & Inside knob/lever when power is removed from the solenoid.
Latchbolt is deadlocked by an auxiliary latch
Applying power to solenoid; remains locked while power is continuously applied.
Deadbolt operated by:
• Outside or inside key
• Outside & Inside knob/ lever when power is removed from the solenoid
Removing power from solenoid Applying power to solenoid; remains locked while power is continuously applied.
Removing power from solenoid
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty. Applying voltage locks inside & outside knobs/levers simultaneously.
• Outside & inside key
• Outside & Inside knob/lever when power is applied to the solenoid.
Latchbolt is deadlocked by an auxiliary latch
Removing power from solenoid
Deadbolt operated by:
• Outside or inside key
• Outside & Inside knob/ lever when power is removed from the solenoid
Applying power to solenoid; remains unlocked while power is continuously applied.
Removing power from solenoid
Applying power to solenoid; remains locked while power is continuously applied.
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty. Applying voltage locks inside & outside knobs/levers simultaneously.
• Outside knob/lever when power is removed from the solenoid
• Inside knob/lever.
Latchbolt is deadlocked by an auxiliary latch
Applying power to solenoid; remains locked while power is continuously applied.
Removing power from solenoid
Cannot be locked Always unlocked
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty. Temperature control module (TCM) included.
• Outside knob/lever when power is removed from the solenoid
• Inside knob/lever.
Latchbolt is deadlocked by an auxiliary latch
Removing power from solenoid
Applying power to solenoid; remains locked while power is continuously applied.
Cannot be locked
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty.
• Outside knob/lever when power is removed from the solenoid
• Inside knob/lever.
Applying power to the solenoid; remains locked while power is continuously applied
Deadbolt extended by:
Inside thumb turn
Removing power from the solenoid Cannot be locked
Deadbolt retracted by:
• Inside thumb turn
• Inside knob/lever retracts the deadbolt and latchbolt simultaneously
• Outside knob/lever when power is removed
Always unlocked
Always unlocked
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty. Temperature control module (TCM) included.
• Outside knob/lever when power is applied to the solenoid
• Inside knob/lever.
Removing power from the solenoid
Deadbolt extended by:
Inside thumb turn
Applying power to the solenoid; remains locked while power is continuously applied
Deadbolt retracted by:
• Inside thumb turn
• Inside knob/lever retracts the deadbolt and latchbolt simultaneously
• Outside knob/lever when power is removed
Powered by 12 or 24 volts AC/DC & 1.10 or 0.75 amps, continuous duty.
Cannot be locked Always unlocked
ATTENTION: Locksets that secure both sides of the door are controlled by building codes and the Life Safety Code ®
.
In an emergency exit situation, failure to quickly unlock the inside lever could be hazardous or even fatal.
OMECHANICAL LOCKS
9
8KW & 9KW ELECTRIFIED LOCKS – SPECIFICATIONS
Types:
• 24 volts DC only — 0.18 amps intermittent or continuous duty.
• EU: Electrically Unlocked (Fail Secure)
• EL: Electrically Locked (Fail Safe)
Approval Listings:
• UL listed for GYQS Electrically-controlled singlepoint locks or latches.
• This product has been approved by the California State Fire
Marshal (CSFM) pursuant to section13144.1 of the California
Health and Safety Code.
• Approved by the city of New York Board of Standards and
Appeals under calendar number 730-89-SA. See CSFM listing No.
4136-1175:103. It is subject to re-examination, revision and possible cancellation.
93KW Cylindrical Electrically-Operated Lockset
† NOTE:
8KW/9KW Electromechanical locksets are intended for use on 1
3
/
4
" minimum thick doors. Consult your local Stanley office when installing
8KW/9KW electromechanical locksets on doors less than 1
3
/
4
" thick.
10
8KW & 9KW ELECTRIFIED LOCKS – HOW TO ORDER
93KW 7 DEU 14 K STK 626 TL
Series Core
Housing
Function Knob/Lever
Style
Trim
Style
Strike
Package
Finishes* Options
8KW:
83KW– 2 3 /
4
"
84KW– 3 3 /
4
"
85KW– 5"
9KW:
93KW– 2 3 /
4
"
94KW– 3 3 /
4
"
95KW– 5"
0– keyless
7– 7 pin housing accepts all Best cores
DEU– electricallyunlocked
DEL– electricallylocked
8KW:
4– round
6– tulip
9KW:
14– curved return
15– contour angle return
16– curved no return
C– 3" convex
D– 3 1 /
2
" convex
K– 3" convex— no ring
L– 3 1 /
2
" convex
—no ring
STK–
2 3 /
4
" ANSI
S3–
4 7 /
8
" ANSI
605 606
611 612
613 618
619 625
626 690
(See Below) (page 11) ( page 11)
* Handles are made from a zinc alloy, and have been plated to be equivalent in appearance to the finishes listed.
8KW only:
BRK– breakaway knob
KNL– knurled knob
TAC– tactile knob
9KW only:
AL– abrasive lever
LM– lost motion
RQE– request-to-exit
TL– tactile lever
Note: specify inside (I), outside
(O), or both (B) for AL, TL, TAC,
KNL options
8KW & 9KW:
LL– lead lined
SH– security head screws
3
/
4 – 3
/
4
" throw latch
( page 3)
8KW & 9KW ELECTRIFIED LOCKS – FUNCTIONS
Function Latch
Operated by
Outside Knob or Lever
Locked by Unlocked by
Inside Knob or Lever
Locked by Unlocked by
DEL-Locked • Rotating the inside knob/lever, OR
• Rotating the outside knob/lever—only when power is off, OR
• Turning the key in the outside knob/lever.
Applying 24 volts DC.
The outside knob/lever remains locked only while power is on.
Switching off 24 volts DC.
Locks are powered by 24 volts DC and 0.18 amps, continuous duty.
Cannot be locked.
Always unlocked.
DEU-Unlocked • Rotating the inside knob/lever, OR
• Rotating the outside knob/lever—only when power is on, OR
• Turning the key in the outside knob/lever.
Switching off 24 volts DC. Applying 24 volts DC.
The outside knob/lever remains locked only while power is off.
Locks are powered by 24 volts DC and 0.18 amps, continuous duty.
Shading indicates a ridged lever/ knob in a non-energized state.
Cannot be locked.
Always unlocked.
IDH MAX ® & ELECTROMECHANICAL LOCKS
KNOB TRIM VARIATIONS
#4 knob #6 knob
LEVER TRIM VARIATIONS
#3 lever #12 lever
MORTISE ROSE TRIM
#14 lever #15 lever
#16 lever #17 lever
CYLINDRICAL ROSE TRIM
H Rose S Rose C Rose D Rose K Rose L Rose
ESCUTCHEON TRIM VARIATIONS
J Escutcheon M Escutcheon N Escutcheon MS Escutcheon
M E C H A N I C A L L O C K S
Prox Escutcheon
11
12
ELECTRIFIED ACCESSORIES
8W599
Features
• Offers exceptionally high power for its compact size
• UL listed
• Thermally fused
• Convenient 4 point mounting provision allows rapid installation in a standard 1 /
2
" knockout
• Foot-mounts for surface installation
• Pre-stripped pigtails provided for quick primary connection
• Secondary connection by screw terminals
• Sturdy nylon bobbin construction
• Cadmium plated finish
Specifications
Primary voltage: 120 VAC (Wire Leads)
Secondary voltage: 24 VAC (Screw Terminals)
Secondary VA: 40 volts-amperes
Dimensions: 2 1 /
4
" x 2 1 /
8
" x 2 15 /
16
"
To order specify: 8W599
Transformer
Function/Application
Transforms 120 volts AC to 24 volts AC. (To get 24 volts
DC, use with 8WCON, AC to DC converter.) Typically used as a power supply for electrically-operated locks.
8WCON
Features
• 400 Ampere surge capability
• Electrically isolated base
• UL recognized
• Single-phase, full wave bridge
Specifications
Average forward current: 25 amps
Case: Plastic case with an electrically isolated aluminum base
Polarity: Terminal designation embossed on case: +DC output,
-DC output, AC not marked
Mounting position: Bolt down. Gain the highest heat transfer efficiency through the surface opposite the terminals. Use silicone heat sink compound on mounting surface for maximum heat transfer.
Terminals: Suitable for “fast-on” connections. Readily solderable and corrosion resistant. Soldering is recommended for applications greater than15 amperes.
Mounting torque: 20 inch-pounds maximum
Case size: 1.030 x 1.030 inches
Temperature range: -85° to 347°F (-65° to + 175°C)
To order specify: 8WCON
AC to DC Converter
Full wave bridge rectifier
Function/Application
Converts AC (alternating current) to DC (direct current) for locking circuit applications. (Typically used with
8W599 transformer.)
8WBU-1-A / 8WBU-1-N
Features
• Positive “snap” feedback
• Industrial-grade switch designed for rugged control applications
• Factory assembled with trimplate
• Standard or narrow plate available
• 1 3 /
16
" dia. mushroom head—red in color
Specifications
Electrical rating: 28VDC or 115 VAC, 10A resistive, 5A inductive,
3A lamp load (see terminology on the back cover)
Switch type: SPST-NO-DB, FORM-X contacts, 25,000 cycles at
8WBU-1-A
Standard plate
8WBU-1-N
Narrow plate full load, 50,000 cycles mechanical life
Mounting hole:
5
/
8
" (.625) dia.
Function/Application
Switch dim.: 1.187 dia.x 1.528 overall length
Std. wall plate: 2
3
/
4
" x 4
1
Narrow wall plate: 1
1
/
2
"
/
2
" x 4
1
/
2
"
Normally open push-button switch provides momentary switch closure when pressed. Typically used to momentarily energize electrified locks or strikes or used as a request-to-
Material/finish: Satin stainless steel exit switch on access control systems.
Wire leads: Two 6" long 20 AWG insulated wire leads
To order specify: 8WBU-1-A standard plate 8WBU-1-N narrow plate
IDH MAX ® & ELECTROMECHANICAL LOCKS
Features
• All circuitry completely sealed
• Wire leads for easy installation
• Through hole mounting
• Usable on other manufacturer’s 12 & 24 VDC locksets
Specifications
Wire leads: 18 AWG stranded vinyl insulated wire approx. 6" in length
Voltage input: 24 volts AC/DC
Voltage output: 12 volts DC; 24 volts DC minimum at one (1) amp max. load for approx. one (1) second, then 15 to 17 VDC regulated output until input voltage is interrupted.
Output protection: Short circuit current limiting set at one (1) amp; output reverse hookup protection for internal circuitry only.
Operating temp: -4 to 158°F (-20 to 70°C)
Size: 2" x 2 1 /
8
" x 1 3 /
8
"
To order specify: 8WTCM
ELECTRIFIED ACCESSORIES
8WTCM
Temperature control module
Function/Application
A temperature control module (TCM) reduces the amount of current flow to a lockset one second after energizing, thereby lowering the temperature of the lockset trim. A TCM may be needed on an electrified mortise or electrified cylindrical lockset if energized for long periods of time. The TCM is not used with any IDH-Max function. The TCM Must Be ordered separately for DEL, WEU, NXEU functions, but is automatically included with 44H–47H DEL\, WEL,
NXEL functions.
TERMINOLOGY
Closed–A state in which a connection exists between the common terminal and another terminal on the switch. See also Open.
Common terminal–A terminal on a switch whose contact can be connected to one or more terminals on the switch.
Door monitor switch–A switch that monitors whether the door is open or closed. This switch is used to detect a forced entry, or a door that is propped open.
Inductive load–An electrical device such as a motor, relay, or solenoid. Note: this type of load can cause arcing across switch contacts and may burn the contacts. See also Resistive load and Lamp load.
Lamp load –An electrical device that produces light using a tungsten filament, such as an incandescent light bulb. Note: this type of load can cause surges of current upon contact closure. This may cause the contacts to weld together. See also
Inductive load and Resistive load.
Maintained–Remaining in a given state until the switch lever or button is actuated. Actuating the switch lever or button causes the switch to change to another maintained state.
Momentary–Remaining in a given state only as long as an external force is applied to the switch lever or button.
NC–(Normally Closed) Switch contacts that are closed as long as no external force is applied to the switch lever or button
NO–(Normally Open) Switch contacts that are open as long as no external force is applied to the switch lever or button.
Open–A state in which no connection exists between the common terminal or any other terminal on the switch.
Pole–The number of independent circuits in a switch. For example, a double-pole, single-throw switch can control two separately powered motors. See also Throw.
Resistive load–An electrical device, such as a heater, having none of the characteristics of an inductive or lamp load. This type of load is the least severe on the switch because only a small amount of arcing occurs when the switch contacts open and close. See also Inductive load and Lamp load.
RQE–Request-to-exit. A switch that allows the user to exit without setting off an alarm. The 34–37H mortise lock can be supplied with an internal request-to-exit switch. Turning the inside knob or lever actuates the switch and, when wired to an alarm system, sends a signal to disable or sound an alarm, start a timer, etc.
Throw–The number of circuits, or contacts controlled by each pole. For example, a single-pole, double-throw switch can control a motor with two contacts—a forward contact, and a reverse contact. See also Pole.
1300– Integrated BAS1300/LNL1300 reader electronics board or (ISC) Intelligent System Controller is embedded behind the escutcheon secured and out of site. Functions with B.A.S.I.S./Mercury on-line equipment only.
OMECHANICAL LOCKS
13
ELECTRIC SWITCH LOCK – INTRODUCTION
Stanley Security Solutions offers a line of electric switch locks available in various “on-off” and “momentary” keyed switch functions.
Circuitry variations are available in single, double and triple pole with varied voltage and amperage ratings. Units may be keyed into any BEST system. The BEST interchangeable core offers versatility and adaptability for new and existing electrical controls, panels, machines, etc.
Features
• Double D lock cylinder prevents slipping and turning
• Screw terminals on all switch locks (except the 1W7A1) provides ease of installation
• All switches are UL recognized or listed
Note on functionality: Switch lock keys can only be removed in the 12 o’clock position.
How to select a switch lock
1. Determine the electrical requirements for the device being controlled:
A. Voltage (for example: 115 VAC or 24 VDC)
B. Current or horsepower (for example: 6 amps or
1 /
2 horsepower)
C. Type of load
• Resistive (for example, heater elements)
• Inductive (for example, motors, large transformers)
• Lamp (for example, incandescent lights)
2. Determine the switch configuration (poles and throws) and key removal condition:
A. Poles To determine the number of poles, find how many wires from the power source need to be switched on and off by the switch lock.
B.
Throws To determine the number of throws, find how many wires to the device the switch needs to control. For example, if a switch needs two different “on” conditions (low and high speed), two throws are needed. Or if the device is simply an “on-off” type (only one wire), you need one throw.
Note: A switch throw may be left unwired and used as an “off” condition.
C. Key removal To determine the key removal condition, ask the question, “When the key is removed, should the switch be
“off”, or could the switch be either “on” or “off” ?” Although the key can only be removed in the 12 o’clock position, the switch itself may be left in two or three positions. Check each switch lock for key removal switch positions.
3. Use the information collected and find the switch lock that best meets the requirements. Refer to the following catalog pages for a description of each switch lock. If environmental conditions make it necessary that the switch lock be housed in an electrical box, see the Optional boxes (above) for the box that best suits the switch lock and your application.
OPTIONAL BOXES
14
OC1
Standard octagon center mount
3 1 /
2
" x 3 1 /
2
" x 1 5 /
8
"
OC2
Deep octagon offset mount
3 1 /
2
" x 3 1 /
2
" x 3 1 /
4
"
INT
Interior box
4" x 2 1 /
8
" x 1 7 /
8
"
SWR
Standard weather resistant box
4 5 /
8
" x 2 7 /
8
" x 2 1 /
4
"
HOW TO ORDER – 1W ELECTRIC SWITCH LOCK
1W
Series
7
Core
Housing
1W 7– 7 pin housing accepts all
Best cores
B1
Function Finishes see pages
15–19
626
605 606
611 612
613 619
622 625
626 690
SWR
Box see above
DWR
Deep weather resistant box
4 5 /
8
" x 2 7 /
8
" x 3"
IDH MAX ® & ELECTROMECHANICAL LOCKS
1W ELECTRIC SWITCH LOCKS
1W7A1
Contacts ..............................................................................................Silver or gold flash
Contact rating ..........................................................................28 VDC, 10 amps resistive
28 VDC, 3 amps inductive, lamp
125 VAC, 10.1 amps resistive
250 VAC, 10.1 amps resistive
Horsepower rating ..................................................................................125 VAC, 1 /
4
HP
Operating temperature ................................................-85°F to +257°F (-65° to +125°C)
Switch type ....................................................................SPDT (Single pole-double throw)
Switch lock action ..............................................................................Maintained (on-on)
Number of switches per assembly ............................................................................One
2 1 /
16
"
1W7A1
31
/ 32 "
1
5
/
32
"
5 /
16
"
Hole cutout
Key & switch positions
Key pos.1– Swt. pos.1
15 /
16
"
Back view
Key pos.2– Swt. pos.2
3 /
4
"
1 /
8
"
Side view
Remove key Optional boxes
DWR
INT
OC1
OC2
Key pos. 1only Swt.
1W7B1 & 1W7J1
Contact rating ........................................................................30 VDC, 15 amps, resistive
125 VDC, 0.6 amps, resistive
250 VDC, 0.3 amps, resistive
125 VAC, 15 amps, resistive
25 VAC, 5 amps, lamp
250 VAC, 15 amps, resistive
Horsepower rating ..........................................................................125–250 VAC, 1 /
2
HP
Operating temperature ....................................................................up to +176°F (+80°C)
Switch type ....................................................................SPDT (Single pole-double throw)
Switch lock action ..............................................................................Maintained (on-on)
Number of switches per assembly ........................................1W7B1: One 1W7J1: Two
1W7B1—One switch
31 /
32
"
1 5 /
32
"
Hole cutout
Key & switch positions
Back view Side view
The shaded area shows the additional 1W7J1 switch and cam length.
Remove key Optional boxes
OC1 DWR
OC2 INT
SWR (1W7B1 only)
Key pos.1– Swt. pos.1 Key pos.2– Swt. pos.2 Key pos. 1 only
Swt. pos. 1
OMECHANICAL LOCKS
1W7J1—Two switches
15
1W ELECTRIC SWITCH LOCKS
1W7B2 & 1W7J2
Contact rating .................................................................. 30 VDC, 15 amps, resistive
125 VDC, 0.6 amps, resistive
250 VDC, 0.3 amps, resistive
125 VAC, 15 amps, resistive
125 VAC, 5 amps, lamp
250 VAC, 15 amps, resistive
Horsepower rating ......................................................................125–250 VAC, 1 /
2
HP
Operating temperature ..............................................................up to +176°F (+80°C)
Switch type ..............................................................SPDT (Single pole-double throw)
Switch lock action ..........................................................................Maintained (on-on)
Number of switches per assembly ..................................1W7B2: One 1W7J2: Two 1W7B2—One switch
31 /
32
"
1 5 /
32
"
Hole cutout
Back view
The shaded area shows the additional 1W7J2 switch and cam length.
Key & switch positions
Side view
Remove key Optional boxes
OC1 DWR
OC2 INT
SWR (1W7B2 only)
Key pos.1– Swt. pos.1 Key pos. 2
(360°CCW)
Swt. pos. 2 Key pos. 1 and 2
Swt. pos. 1 and 2
1W7B3 & 1W7J3
Contact rating .................................................................. 30 VDC, 15 amps, resistive
125 VDC, 0.6 amps, resistive
250 VDC, 0.3 amps, resistive
125 VAC, 15 amps, resistive
125 VAC, 5 amps, lamp
250 VAC, 15 amps, resistive
Horsepower rating ....................................................................125–250 VAC, 1/2 HP
Operating temperature ..............................................................up to +176°F (+80°C)
Switch type ..............................................................SPDT (Single pole-double throw)
Switch lock action ........................................................................Momentary (on-on)
Number of switches per assembly ..................................1W7B3: One 1W7J3: Two
31 /
32
"
1 5 /
32
"
1W7J2—Two switches
1W7B3—One switch
16
Hole cutout
Back view
The shaded area shows the additional 1W7J3 switch and cam length.
Key & switch positions Remove key
Side view
Optional boxes
OC1 DWR
OC2 INT
SWR (1W7B3 only)
1W7J3—Two switches
Key pos.1– Swt. pos.1 Key pos.2– Swt. pos.2 Key pos.1– Swt. pos.1
IDH MAX ® & ELECTROMECHANICAL LOCKS
1W ELECTRIC SWITCH LOCKS
1W7D2
Contact rating . . . . . . . . . . . . . . . . . . . . . . . . . .110 VAC or VDC, 16 amps, resistive
220 VAC or VDC, 8 amps, resistive
Horsepower rating . . . . . . . . . . . . . . . . . . . . . . . . . . .1 HP @ 125–250 VAC or VDC
Operating temperature . . . . . . . . . . . . . . . . . . . . . . .0°F to +150°F (-18°C to +66°C)
Switch type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .DPST (Double pole-single throw)
Switch lock action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Maintained (off-on)
Number of switches per assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .One
7 /
8
"
1 5 /
32
"
1W7D2
Hole cutout
Limiting plate†
Key & switch positions
Side view
Remove key
Front view
Optional boxes
OC2 DWR
INT SWR
Key pos.1– Swt. pos.1 Key pos.2– Swt. pos.2 Key pos. 1 only
Swt. pos. 1 and 2†
†Installing the limiting plate limits key removal to switch position 1 or 2. The key is always removed in the vertical position (key position 1).
1W7C2
Contact rating ..............................................................110 VAC or VDC, 10 amps, lamp
220 VAC or VDC, 5 amps, resistive
Operating temperature ................................................-40°F to +220°F (-40° to +104°C)
Switch type ......................................................................SPST (Single pole-single throw)
Switch lock action ..............................................................................Maintained (off-on)
Number of switches per assembly ............................................................................One
1W7C2
Front (inside) view
Key & switch positions
Side (inside) view
Remove key Optional boxes
OC1
OC2
Key pos.1– Swt. pos.1 Key pos.2– Swt. pos.2 Key pos. 3 only
Swt. pos. 1 and 2
OMECHANICAL LOCKS
17
1W ELECTRIC SWITCH LOCKS
1W7E2
Contact rating 110 VAC, 15 amps, resistive
Horsepower rating
220 VAC, 10 amps, resistive
125–250 VAC or VDC,
3
/
4
HP; 1, 2, or 3 phase
Operating temperature ........................................................0 to +150°F (-18°C to 66°C)
Switch type ....................................................................TPDT (Triple pole-double throw)
Switch lock action ............................................Maintained Momentary (on-center off-on)
Number of switches per assembly ............................................................................One
7 /
8
"
1 5 /
32
"
Hole cutout
1W7E2
Limiting plate *
Key & switch positions
Side view Front view
Remove key Opt. box
OC2
Key pos.1
Swt. pos.1
Key pos.2
Swt. pos.2
Key pos.3
Swt. pos.3
Key pos. 1 only
Swt. pos. 1, 2, and 3*†
*Installing the limiting plate limits key removal to switch position 2, or 3. The key is always removed in the vertical position (key position 1). The limiting plate is available for 1W7E2 only.
1W7K4
Contact rating ......................................................................110 VAC, 15 amps, resistive
220 VAC, 10 amps, resistive
Horsepower rating .................................................................................. 250 VAC, 1 /
2
HP
Operating temperature ..................................................................up to +221°F (+105°C)
Switch type ..................................................................DPDT (Double pole-double throw)
Switch lock action ..............................................................Momentary (on-center off-on)
Number of switches per assembly ............................................................................One
7 /
8
"
1 5 /
32
"
Hole cutout
Key & switch positions
1W7K4
Side view
Remove key
Back view
Opt. boxes
OC2
18
Key pos.1 Swt. pos.1 Key pos 2 Swt. pos.2 Key pos.3 Swt. pos.3 Key pos. 1 only
Swt. pos. 1 only
IDH MAX ® & ELECTROMECHANICAL LOCKS
1W ELECTRIC SWITCH LOCKS
1W7L2
Contact rating ..........................................................110 VAC or VDC, 12 amps, resistive
220 VAC or VDC, 6 amps, resistive
Operating temperature ..................................................................up to +221°F (+105°C)
Switch type ....................................................................SPDT (Single pole-double throw)
Switch lock action ..............................................................................Maintained (on-on)
Number of switches per assembly ............................................................................One
7 /
8
"
1 5 /
32
"
1W7L2
Hole cutout
Limiting plate
†
Key & switch positions
Side view
Remove key
Front view
Optional boxes
DWR
OC2
Key pos. 1
Swt. pos. 1
Key pos. 2
Swt. pos. 2
Key pos. 3 only
Swt. pos. 1 and 2†
†Installing the limiting plate limits key removal to switch position 1 or 2. The key is always removed in the vertical position (key position 3).
1W7P4 & 1W7R4
Contact rating ..........................................................................30 VDC, 15 amps, resistive
125 VDC, 0.6 amps, resistive
250 VDC, 0.3 amps, resistive
125 VAC, 15 amps, resistive
125 VAC, 5 amps, lamp
250 VAC, 15 amps, resistive
Horsepower rating ............................................................................125–250 VAC, 1 /
2
HP
Operating temperature ....................................................................up to +176°F (+80°C)
Switch type ....................................................................SPDT (Single pole-double throw)
Switch lock action ..............................................................................Momentary (on-on)
Number of switches per assembly ........................................1W7P4: Two 1W7R4: Four
1 1 /
2
"
2 5 /
16
"
1 29 /
32
"
31 /
32
"
1W7P4—two switches
1 5 /
32
" 2 7 /
8
"
1 /
8
"
Hole cutout
Back view
The shaded area shows the additional 1W7R4 switches and cam length.
Key & switch positions
Key pos.1 Swt. pos.1 Key pos.2 Swt. pos. 2
Side view
Remove key Boxes
SWR†
INT†
DWR
†1W7P4 only
Key pos.3 Swt. pos.3
Key pos. 1 only
Swt. pos. 1 only
OMECHANICAL LOCKS
1W7R4—four switches
19
For more information on Stanley Security Solutions’ products, services, and office locations visit our web site at www.stanleysecuritysolutions.com
Product information contained in this catalog has been compiled and presented with as much care and completeness as is reasonably possible. Errors or mistakes may be present, and in many cases, reliance has been placed on information supplied by other manufacturers which may be in error or which may be subject to changes or modifications by the manufacturer without notice and without obligation. Therefore, no guarantee can be made or should be assumed or implied with regards to product information contained in this catalog.
Stanley Security Solutions, Inc.
6161 E. 75th Street Indianapolis, Indiana 46250 www.stanleysecuritysolutions.com
© 2007 Stanley Security Solutions, Inc. and Stanley Logistics
010M 707FP
BAS019
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 introduction
- 2 features
- 3 1300 comparison chart
- 3 HM, KM, HW & KW options
- 4 specifications, how-to-order
- 5 functions
- 6 specifications
- 6 how-to-order
- 7 functions
- 7 40HW electrified specification
- 8 40HW electrified how-to-order
- 8 40HW electrified functions
- 10 8KW/9KW electrified specification
- 10 8KW/9KW electrified how-to-order
- 10 8KW/9KW electrified functions
- 11 Trim variations
- 13 Electrified accessories
- 13 Terminology
- 14 1W electric switch lock introduction
- 14 Optional boxes
- 14 1W electric switch lock how-to-order
- 15 1W electric switch locks