Liebert® APS™
User Manual – 5-20kVA Modular UPS
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SAVE THESE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
GLOSSARY OF SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.0
PRODUCT INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1.1
System Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.3
Operating Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.4
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.5
Major Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.5.1
UPS Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.5.2
User Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.5.3
System Control Module and System Monitor Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.5.4
Power Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.5.5
Battery Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.5.6
Charger Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.5.7
External Battery Cabinet (EBC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.0
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1
Unpacking Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1.1
Installation Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1.2
Installation Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.1.3
Installation Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.2
Unloading the UPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.3
Mechanical Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.4
2.5
2.3.1
Tower Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.3.2
Rack Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.4.1
Installing Power Module, Battery Module and Charger Module. . . . . . . . . . . . . . . . . . . . . . . 22
2.4.2
Install System Control and System Monitor Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2.5.1
Transformer-Free UPS Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
2.5.2
Transformer-Based UPS Cable Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2.5.3
Transformer-Free UPS—Dual Inverter Frames. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.5.4
Connecting External Battery Cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2.5.5
Connecting Integrated Power Output Distribution (POD) . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
2.5.6
Commissioning/Startup Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3.0
COMMUNICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.1
Liebert IntelliSlot Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.2
Dry Contact Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.3
REPO (Remote Emergency Power Off) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
i
3.4
Long Run Time (LRT) Battery Temperature Probe Terminals . . . . . . . . . . . . . . . . . . . . . . . 41
3.5
USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.6
Liebert MultiLink® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.7
LCD Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.0
OPERATION AND DISPLAY PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
4.2
LCD Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.3
4.2.1
Startup Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.2.2
Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.2.3
Default Screen/Screen Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
LCD Screen Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.3.1
AC Mains Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
4.3.2
Battery Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.3.3
Output Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
4.3.4
Load Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.3.5
UPS Information Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4.3.6
Redundancy Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
4.3.7
Settings Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.4
Entering a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.5
Setting or Changing a Parameter Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
4.5.1
Battery Setting Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4.5.2
Language Selection Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4.5.3
Alarms Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
4.5.4
Records Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
4.5.5
Module Replacement Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.5.6
Prompt Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
5.0
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
5.1
Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
5.2
Module Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
5.3
Module Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
5.3.1
Removing Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
5.3.2
Replacing the User Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
6.0
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.1
Proper Care. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.2
Scheduled Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.3
Cleaning Fan Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.3.1
Top Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.3.2
Bezel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
6.3.3
Bottom Fan Filter—Transformer-Based Frames Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
7.0
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
7.1
Estimated Battery Run Times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
7.1.1
Tables for UPS Where Model Number Digits 1-3 are AS1 or ASA . . . . . . . . . . . . . . . . . . . . . 72
ii
7.2
Estimated Battery Run Times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
7.2.1
7.3
Estimated Battery Run Times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
7.3.1
7.4
Tables for UPS Model Number Where Digits 1-3 are AS4 or ASD . . . . . . . . . . . . . . . . . . . . . 85
Estimated Battery Run Times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
7.5.1
7.6
Tables for UPS model number digits 1-3 are AS3 or ASC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Estimated Battery Run Times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
7.4.1
7.5
Tables for UPS Model Number Where Digits 1-3 are AS2 or ASB . . . . . . . . . . . . . . . . . . . . . 77
Tables for UPS Model Number Where Digits 1-3 are AS5 or ASE . . . . . . . . . . . . . . . . . . . . . 89
Estimated Battery Run Times. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
7.6.1
Tables for UPS Model Number Where Digits 1-3 are AS6 or ASF . . . . . . . . . . . . . . . . . . . . . 93
FIGURES
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Figure 24
Figure 25
Figure 26
Figure 27
Figure 28
Figure 29
Figure 30
Figure 31
Figure 32
Figure 33
Figure 34
Figure 35
Figure 36
16-bay transformer-free UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
10-bay transformer-free UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
12-bay transformer-based UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
16-bay transformer-based UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Operating principle diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
UPS frames, bezels removed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
User interface module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Liebert APS system control module and the system monitor module . . . . . . . . . . . . . . . . . . . . . . 12
Liebert APS power module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Battery module appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Appearance of the charger module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
External battery cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Front and rear installation clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Remove the mounting brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Connect the ramp and remove UPS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Adjust the leveling feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installation position and drilling hole dimensions for stationary mounting. . . . . . . . . . . . . . . . . 17
Install cage nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Install the tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Install the guide rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Install the brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Push the UPS frame into the rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Fix the UPS frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Install the metal plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Installation completed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Insert the power module, battery module and charger module . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Lever and fastener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Remove large plastic bezel and user interface module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Insert the System Control and System Monitor module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Lever and fastener on System Control and System Monitor Module . . . . . . . . . . . . . . . . . . . . . . 24
Knockouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Connection in single-phase input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Connection in 3-phase input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Setting bypass voltage jumper (default: 208VAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Setting bypass voltage jumper (200/220/230/240VAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Configuring the neutral/earth jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
iii
Figure 37
Figure 38
Figure 39
Figure 40
Figure 41
Figure 42
Figure 43
Figure 44
Figure 45
Figure 46
Figure 47
Figure 48
Figure 49
Figure 50
Figure 51
Figure 52
Figure 53
Figure 54
Figure 55
Figure 56
Figure 57
Figure 58
Figure 59
Figure 60
Figure 61
Figure 62
Figure 63
Figure 64
Figure 65
Figure 66
Figure 67
Figure 68
Figure 69
Figure 70
Figure 71
Figure 72
Figure 73
Figure 74
Figure 75
Knockouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connection method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Knockouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Secure cables on cable bridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting external battery cabinet to a transformer-free UPS . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting external battery cabinet (transformer-based UPS) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert IntelliSlot communication port location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin layout of the dry contacts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REPO connector pin layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REPO switch connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin layout of the temperature sensor terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LCD port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation and display panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User interface module layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Startup screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Default screen/screen saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mains screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS info screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Redundancy screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings screens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery settings screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Language selection screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarms screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Records screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module replacement screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example of prompt window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module LED location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lever and fastener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pull out a battery module, a power module or a charge module . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the user interface module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replace/clean the top filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replace/clean the bezel filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replace/clean the bottom fan filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
31
32
33
33
34
35
35
38
39
40
40
41
42
43
44
45
45
50
50
51
51
52
52
53
54
56
56
57
57
58
58
63
64
65
66
67
68
68
TABLES
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Frame designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Cable connection method reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Input cable selection list—60Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Input cable selection list—50Hz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Key to Figures 32 and 33 UPS wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Input cable selection for transformer-based frames (60 Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Input cable selection for transformer-based frames (50 Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Key to Figure 38 UPS input wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Key to Figure 38 UPS output wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
iv
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Table 20
Table 21
Table 22
Table 23
Table 24
Table 25
Table 26
Table 27
Table 28
Table 29
Table 30
Table 31
Table 32
Table 33
Table 34
Table 35
Table 36
Table 37
Table 38
Table 39
Table 40
Table 41
Table 42
Table 43
Table 44
Table 45
Table 46
Table 47
Table 48
Table 49
Table 50
Table 51
Table 52
Table 53
Table 54
Maximum load capacity of the output winding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input cable selection for Transformer-free Dual Inverter frames(50/60 Hz). . . . . . . . . . . . . . . . .
Input cable selection for Transformer-free Dual Inverter frames(50/60 Hz). . . . . . . . . . . . . . . . .
EBC DIP switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin definition of dry contact port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin definition of the REPO dry contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pin definition of the temperature sensor terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LED descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audible alarm descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control buttons functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function descriptions of menu button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Item description of system information window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Item description of menu window and data window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function descriptions of menu buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information and actions required for the prompt window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm message list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Descriptions of module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert APS specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rated input voltage range (Unit: VAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert APS external battery cabinet specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-bay, single-phase, no transformer unit Type N (& UPS model number digit 6 = N) . . . . . . . .
10-bay, single-phase, no transformer unit Type N (& UPS model number digit 6 = N) . . . . . . . .
10-bay, single-phase, no transformer unit Type R (& UPS model number digit 6 = R) . . . . . . . .
10-bay, single-phase, no transformer unit Type B (& UPS model number digit 6 = B) . . . . . . . .
10-bay, single-phase, no transformer unit Type F (& UPS model number digit 6 = F) . . . . . . . .
16-bay, single-phase, no transformer unit Type N (& UPS model number digit 6 = N) . . . . . . . .
16-bay, single-phase, no transformer unit Type R (& UPS model number digit 6 = R) . . . . . . . .
16-bay, single-phase, no transformer unit Type B (& UPS model number digit 6 = B) . . . . . . . .
16-bay, single-phase, no transformer unit Type F (& UPS model number digit 6 = F) . . . . . . . .
12-bay, single-phase, transformer-based unit Type N (& UPS model number 6 = N) . . . . . . . . .
12-bay, single-phase, transformer-based unit Type R (& UPS model number 6 = R). . . . . . . . . .
12-bay, single-phase, transformer-based unit Type B (& UPS model number 6 = B). . . . . . . . . .
12-bay, single-phase, transformer-based unit Type F (& UPS model number 6 = F) . . . . . . . . . .
16-bay, single-phase, transformer-based unit Type N (& UPS model number 6 = N) . . . . . . . . .
16-bay, single-phase, transformer-based unit Type R (& UPS model number 6 = R). . . . . . . . . .
16-bay, single-phase, transformer-based unit Type B (& UPS model number 6 = B). . . . . . . . . .
16-bay, single-phase, transformer-based unit Type F (& UPS model number 6 = F) . . . . . . . . . .
10-bay, two-phase, no transformer unit Type N (& UPS model number 6 = N) . . . . . . . . . . . . . .
10-bay, two-phase, no transformer unit Type R (& UPS model number 6 = R) . . . . . . . . . . . . . .
10-bay, two-phase, no transformer unit Type B (& UPS model number 6 = B) . . . . . . . . . . . . . .
10-bay, two-phase, no transformer unit Type F (& UPS model number 6 = F). . . . . . . . . . . . . . .
16-bay, two-phase, no transformer, unit Type N (& UPS model number 6 = N) . . . . . . . . . . . . .
16-bay, two-phase, no transformer unit Type R (& UPS model number 6 = R) . . . . . . . . . . . . . .
16-bay, two-phase, no transformer unit Type B (& UPS model number 6 = B) . . . . . . . . . . . . . .
16-bay, two-phase, no transformer unit Type F (& UPS model number 6 = F). . . . . . . . . . . . . . .
v
31
32
32
35
39
40
41
43
44
44
44
45
46
49
59
60
63
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
vi
Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important safety instructions. Read all safety, installation and operating
instructions before operating the Liebert® APS™ modular UPS system. Adhere to all warnings on the
unit and in this manual. Follow all operating and user instructions. Individuals must fully
understand this equipment to install and operate it.
This product is designed for commercial/industrial use only. It is not intended for use with life support
or other designated critical devices. Maximum load must not exceed that shown on the rating label.
Install and operate the unit only in an indoor clean environment, free from conductive contaminants,
moisture, flammable liquids, gases and corrosive substances. This Liebert APS contains no user
serviceable parts other than the user replaceable modules. Refer all faults to your local dealer, local
Emerson Network Power representative or the Emerson Network Power Liebert Services Group.
The Liebert APS UPS system is designed for use on a properly earthed (grounded) “TN” electrical
supply, for installation by qualified personnel. A qualified electrician must review and approve
customer supplied wiring, circuit breakers, and intended loads and verify correct input, output, and
earth connections to ensure compliance with the technical standards and local electrical codes of
practice. Installation instructions and warning notices are found in this manual.
! WARNING
Risk of electric shock. Can cause equipment damage, injury and death.
The battery can present a risk of electrical shock and high short circuit current. The following
precautions should be observed before replacing the battery pack:
•
•
•
•
•
Wear rubber gloves and boots
Remove rings, watches and other metal objects.
Use tools with insulated handles.
Do not lay tools or other metal objects on the batteries.
If the battery kit is damaged in any way or shows signs of leakage, contact your local Emerson representative immediately.
• Do not dispose of batteries in a fire. The batteries may explode.
• Handle, transport and recycle batteries in accordance with local regulations.
! WARNING
Risk of electric shock and fire. Can cause equipment damage, injury and death.
Although the Liebert APS UPS has been designed and manufactured to ensure personal
safety, improper use can result in electrical shock or fire. To ensure safety, observe the
following precautions:
• Clean the UPS with a dry cloth. Do not use liquid or aerosol cleaners.
• Never block or insert any objects into the ventilation holes or other openings of the UPS.
• Do not place the Liebert APS where it might be damaged.
! WARNING
Risk of electric shock. Can cause equipment damage, injury and death.
This UPS contains no user-serviceable parts except for the user-replaceable module
assemblies. The UPS On/Off push button does not electrically isolate internal parts.
All service and maintenance operations must be performed by properly trained and qualified
personnel. Under no circumstances should unqualified or unauthorized personnel attempt to
gain access to the internal portions of the Liebert APS.
1
Liebert® APS™
Important Safety Instructions
ELECTROMAGNETIC COMPATIBILITY—The Liebert APS complies with the limits of Category
C2, pursuant to IEC/EN/AS 62040-2, and for a Class A digital device, pursuant to Part 15 of FCC
rules. Operation is subject to the following conditions:
• The output cables shall be no longer than 10m (32ft).
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause
undesired operation. Operating this device in a residential area is likely to cause harmful
interference that users must correct at their own expense.
The Liebert APS complies with the requirements of EMC Directive 2004/108/EC and the published
technical standards. Continued compliance requires installation in accordance with these
instructions and use of accessories approved by Emerson.
Operate the UPS in an indoor environment only in an ambient temperature range of 0-40°C
(32-104°F). Install it in a clean environment, free from moisture, flammable liquids, gases and
corrosive substances.
Do not continue to use the UPS if the front panel indications are not in accordance with these
operating instructions or the UPS performance alters in use. Refer all faults to your local service
dealer.
Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and
the required precautions. Keep unauthorized personnel away from the batteries. Proper disposal of
batteries is required. Refer to your local laws and regulations for disposal requirements.
Never block or insert any object into the ventilation holes or other openings.
DO NOT CONNECT equipment that could overload the UPS or demand DC current from the UPS,
for example: electric drills, vacuum cleaners, laser printers, hair dryers or any appliance using half
wave rectification.
Storing magnetic media on top of the UPS may result in data loss or corruption. Turn Off and isolate
the UPS before cleaning it. Use only a soft dry cloth; never use liquid or aerosol cleaners.
Information for the Protection of the Environment
UPS SERVICING—This UPS makes use of components dangerous for the environment (electronic
cards, electronic components). The components removed must be taken to specialized collection and
disposal centers.
NOTICE TO EUROPEAN UNION CUSTOMERS: DISPOSAL OF OLD
APPLIANCES—This product has been supplied from an environmentally aware
manufacturer that complies with the Waste Electrical and Electronic Equipment
(WEEE) Directive 2002/96/CE.
The crossed-out trash bin symbol at right is placed on this product to encourage
users to recycle components and units whenever possible. Please be
environmentally responsible and recycle this product through your recycling
facility at its end of life. Do not dispose of this product as unsorted municipal
waste. Follow local municipal waste ordinances for proper disposal provisions to
reduce the environmental impact of waste electrical and electronic equipment (WEEE).
For information regarding the scrapping/disposal of this equipment, please browse
www.eu.emersonnetworkpower.com (Products section or Contact us section) or call Emerson’s
worldwide technical support.
• Toll Free Outside of North America: 00 80011554499
• Toll Number Based in Italy: +39 0298250222
• Toll Free in North America: 1-800-LIEBERT (1-800-543 2378)
Liebert® APS™
2
Glossary of Symbols
GLOSSARY OF SYMBOLS
Risk of electrical shock
!
Indicates caution followed by important instructions
AC input
AC output
i
-
Requests the user to consult the manual
+
Indicates the unit contains a valve-regulated lead acid battery
PbH2SO4
R
Recycle
DC voltage
Equipment grounding conductor
Bonded to ground
AC voltage
3
Liebert® APS™
Product Introduction
1.0
PRODUCT INTRODUCTION
Congratulations on your purchase of the Liebert APS Uninterruptible Power System (UPS). As with
every other Liebert product, we stand behind our quality. If you have any questions concerning this
UPS, please feel free to contact your local dealer or Liebert representative or call the appropriate
Technical Support number listed on the back of this manual.
To ensure proper installation and operation of this unit, please read this manual thoroughly.
The installation must be completed by trained professionals and follow all local codes. General
operation of the units can be conducted without any specialized training.
This chapter provides the system description, features, operating principle, operating mode, main
components and specifications of the Liebert APS UPS.
1.1
System Description
The Liebert APS power system is a modular UPS designed to provide high reliability. It is intended
for use with workstations, servers, networks, telecoms and other sensitive electronic equipment. It
provides continuous, high-quality AC power to your equipment, protecting it from any power
disturbance due to blackouts, brownouts, surges or noise interference.
The Liebert APS UPS is an easily adaptable UPS system. By simply installing additional power or
battery modules, you can expand your current system capacity, extend your backup runtime, or
provide redundancy. The Liebert APS UPS user interface enables the user to configure the operation
according to application requirements. It also informs the user on the status of the UPS and keeps a
log of events.
The Liebert APS series UPS contains both transformer-free and transformer-based UPS frames. The
use of the transformer-free or transformer-based frames is dependent upon the specific application
requirements. The appearance of the different frames is shown in Figures 1 through 4.
Table 1
Frame designation
UPS Model Number Digits 1-3
Frame Type
Frame Rating
AS1 or ASA or AS5 or ASE
10 Bay Transformer-free
15 kVA redundant
AS2 or ASB or AS6 or ASF
16 Bay Transformer-free
20 kVA redundant
AS3 or ASC
12 Bay Transformer-based
15 kVA redundant
AS4 or ASD
16 Bay Transformer-based
20 kVA redundant
Liebert® APS™
4
Product Introduction
Figure 1
16-bay transformer-free UPS
Liebert IntelliSlot®
Ports
Manual Bypass Breaker
(under cover)
Input Breaker
(under cover)
User
Interface
Module
Bays for
Power,
Charger or
Battery
Modules
Bays for
Battery
Modules
System Control
Module (under
cover)
Power Input and
Output
Terminals
Dry Contacts
and REPO
Connections
System
Enable
Switch
USB Port
Output
Breaker
FRONT VIEW
(Bezels Removed)
Figure 2
External Battery
Cabinet
Connector
POD Ports
REAR VIEW
10-bay transformer-free UPS
Manual Bypass
Breaker (under cover)
Liebert
IntelliSlot
Ports
System
Control
Module
(under
cover)
Input Breaker
(under cover)
User Interface
Module
Power Input
and Output
Terminals
System
Enable
Switch
Dry Contacts
and REPO
Connections
Bays for Power,
Charger, or
Battery Modules
Output
Breaker
USB Port
Bays for Battery
Modules
POD
Port
External
Battery
Cabinet
Connector
FRONT VIEW
(Bezels Removed)
REAR VIEW
5
Liebert® APS™
Product Introduction
Figure 3
12-bay transformer-based UPS
Liebert
IntelliSlot®
Ports
System Control
Module
(under cover)
User Interface
Module
System Enable
Switch
Dry Contacts
and REPO
Connections
Bays for Power,
Charger, or
Battery Modules
USB Port
Bays for
Battery
Modules
External Battery
Cabinet
Connectors
Ports for
PODs
Manual Bypass
Breaker
Output
Breaker
Input Breaker
Power Input
and Output
Terminals
Fans
FRONT VIEW
(Bezels Removed)
Liebert® APS™
REAR VIEW
6
Product Introduction
Figure 4
16-bay transformer-based UPS
System Control
Module
(under cover)
User Interface
Module
Liebert
IntelliSlot®
Ports
Dry Contacts
and REPO
Connections
Bays for Power,
Charger or
Battery Modules
System
Enable
Switch
USB Port
POD
Ports
Battery
Module
Bays
Input
Breaker
Output
Breaker
Manual Bypass
Breaker
(under cover)
External
Battery
Cabinet
Connector
Power Input
and Output
Terminals
Fans
REAR VIEW
FRONT VIEW
(Bezels Removed)
7
Liebert® APS™
Product Introduction
1.2
Features
Liebert APS UPS
•
•
•
•
•
•
•
•
•
•
•
•
•
Flexible extension of capacity, up to 15 or 20kVA modular power, depending upon frame rating
N + 1 redundancy, improving availability
Module design, modules hot-swappable by user
Redundant intelligent module, providing redundant communication path
Intelligent battery management
External large batteries can be connected
Internal automatic and manual bypass
Transformer-based UPS frames provide output isolation transformer
Optional 10A battery charger module
Continuous system monitoring
User-friendly interface with audible alarms and event logs
Supporting hot-pluggable and online update
Compatible with backup generators
Standard Components
•
•
•
•
•
•
•
UPS frame
User interface module: for comprehensive user indications and programmable controls
System control modules and system monitor module: for system monitoring and communications
Power modules: for power conditioning
Battery modules: for backup power
Charger module: option for charging batteries and long run time applications
External battery cabinet: prolongs system run time
Communications
• Dry contacts
• Liebert IntelliSlot communication ports
• USB port
Liebert® APS™
8
Product Introduction
1.3
Operating Principle
The operating principle of the Liebert APS UPS is shown in Figure 5.
Figure 5
Operating principle diagram
Manual Bypass
Output
Input
EMI
Filter
Power
Module(s)
EMI
Filter
Output and
Bypass
Contactor
Transformer models
have an output isolating
transformer
Battery
Module(s)
Wiring
Power
Control
User
Interface
Output
Transformer
System Control
Module
Control
Interface
System Monitor
Module
Communication
The Liebert APS UPS is composed of AC input, EMI filter, power module(s), battery module(s), user
interface, control interface, system control module, output and bypass contactor, manual bypass,
output transformer (certain frames only) and AC output.
9
Liebert® APS™
Product Introduction
1.4
Operating Modes
The Liebert APS UPS is a true online double-conversion system, having the following operating
modes:
•
•
•
•
Normal Mode
Backup Mode
Auto Restart Mode
Bypass Mode
Normal Mode
The power module rectifiers derive power from a utility AC source and supply regulated DC power to
the inverter. The module’s inverter regenerates precise AC power to supply the connected equipment.
The battery charger is in the power module and maintains a float-charge on the batteries of the UPS;
additionally, the optional charger module can also charge the batteries to maintain a quicker
recharge time for long backup time applications.
Backup Mode
When AC utility fails, the connected equipment is supplied power by the inverter, which obtains
energy from the battery modules. The output power will not be interrupted during the failure or
restoration of the AC utility/mains source.
Auto Restart Mode
After a power outage and complete battery discharge, and once AC utility is restored, the UPS will
automatically restart and resume supplying power to connected equipment. This feature is enabled at
the factory, but can be disabled by the user. The user can also program two auto restart delay settings
from the LCD:
• Battery capacity level (%)
• Countdown timer
Bypass Mode
The bypass provides an alternate path for power to the connected equipment and operates in the
following manner:
• Automatic: In the event of an internal fault or should the inverter overload capacity be exceeded,
the UPS performs an automatic transfer of the connected equipment from the inverter to the
bypass source.
• Manual: Should the UPS need to be taken out of service for limited maintenance or repair,
manual activation of the bypass will cause an immediate transfer of the equipment from the
inverter to the bypass source.
Liebert® APS™
10
Product Introduction
1.5
Major Components
This section provides a general description of each component and its functions. Please review this
section carefully, as it will give you a better understanding of how the UPS operates.
1.5.1
UPS Frame
The UPS frames are shown in Figure 6.
Figure 6
UPS frames, bezels removed
Manual Bypass
Breaker
Fan
(behind
display
bracket)
Manual
Bypass
Breaker
Fan
(behind
display
bracket)
10-Bay Transformer-Free UPS
16-Bay Transformer-Free UPS
Fan
(behind
display
bracket)
Fan
(behind
display
bracket)
Manual
Bypass
Breaker
Manual Bypass
Breaker
Fans
Fans
12-Bay Transformer-Based UPS
16-Bay Transformer-Based UPS
NOTE
In Figure 6, the power module and battery module are extended for illustration purposes only.
Extending more than one module at a time could cause the unit to tip over.
All UPS components are located in the Liebert APS frame. The front of the UPS consists of a series of
plastic bezels. By grasping these bezels from the sides and pulling straight out, you can remove the
bezel to reveal the battery/power module bays. The standard-model frame provides cooling fans and a
manual bypass breaker on its top; the transformer-model frame provides a manual bypass breaker on
its bottom and fans on both top and bottom. The user interface module is located above the
power/battery module bays for easy access, operation and for viewing UPS operating information. On
the lower right part of the user interface module, you will see the system control module bays.
11
Liebert® APS™
Product Introduction
1.5.2
User Interface Module
The user interface module is shown in Figure 7.
Figure 7
User interface module
The user interface module is the primary source of communication between the UPS and the user.
The user interface module permits:
•
•
•
•
Viewing the UPS status
Configuring the system
Reviewing the event log
Silencing the audible alarm
Refer to 4.0 - Operation and Display Panel for details on operating the user interface module.
1.5.3
System Control Module and System Monitor Module
The system control module and the system monitor module are the communication backbone of the
UPS. They gather input from all modules and process the data to control the operation of the system,
including monitoring the condition of each module. Except for the silkscreen, the appearance of the
system control module and the system monitor module is as shown in Figure 8.
Figure 8
Liebert APS system control module and the system monitor module
Handle
Securing Hole
Green Status LED
Locking Lever
Yellow Fault LED
Under normal operation, the green status LED will blink and the yellow fault LED will be Off. For
any other condition, refer to 5.0 - Troubleshooting.
Liebert® APS™
12
Product Introduction
1.5.4
Power Module
The power module is shown in Figure 9.
Figure 9
Liebert APS power module
Fan
Green Status LED
Yellow Fault LED
Locking Lever
FRONT VIEW
Each power module is an independent 5kVA unit, consisting of a power factor corrected rectifier,
battery charger and inverter, with associated monitoring and control circuitry. The modules are
connected in parallel for greater capacity and/or redundancy.
The power modules may be added or replaced on-line with no interruption or danger to the connected
equipment or user.
1.5.5
Battery Module
The battery module is shown in Figure 10.
Figure 10 Battery module appearance
Green Status LED
Yellow Fault LED
Locking Lever
FRONT VIEW
When AC utility fails, the battery module will supply power to the load. Each battery module contains
six individual 12V, valve-regulated lead-acid (VRLA) battery blocks. Two battery modules are
connected in series to form a battery string.
Each battery module has monitoring and controls to isolate the battery module in the event of a
battery failure. The battery strings are connected in parallel to provide backup time and/or
redundancy.
NOTE
Two battery modules must be installed in the same layer to make a complete battery string.
The battery modules may be added or replaced on-line with no interruption or danger to the
connected equipment, provided that the UPS is not operating on battery.
Under normal operation, the green status LED will blink continuously and the yellow fault LED will
be Off. For any other condition, refer to 5.0 - Troubleshooting.
13
Liebert® APS™
Product Introduction
1.5.6
Charger Module
Figure 11 shows the charger module.
Figure 11 Appearance of the charger module
Green Status LED
Yellow Fault LED
In AC mains mode, the charger module charges the system battery modules or external battery
cabinet. Each charger module is rated to deliver 10A charging current. The charger module has an
independent control function and maintains real-time communication with the system and the
battery modules to ensure stable charging and fault protection.
The charger module may be added or replaced on-line with no interruption or danger to the user,
connected battery system or connected equipment.
1.5.7
External Battery Cabinet (EBC)
The external battery cabinet is divided into nine layers: the upper seven layers are for use with the
intelligent battery modules, and the lower two are used for overcurrent protection for each battery
cabinet. For normal operation, two battery modules must be inserted in the same layer of the frame to
create a complete string. The battery module strings work in parallel to provide longer backup time
for the UPS. A Liebert APS can be configured with, at most, four external battery cabinets.
An external battery cabinet is shown in Figure 12.
Figure 12 External battery cabinet
Liebert® APS™
14
Installation
2.0
INSTALLATION
This chapter describes UPS installation, including installation preparation, unloading the UPS,
mechanical installation, installing modules and cable connection.
2.1
Unpacking Inspection
Upon receiving the UPS, uncrate it and conduct the following checks:
• Inspect the UPS appearance for shipping damage. Report any shipping damage to the carrier and
send a copy to your Emerson Network Power® representative.
• Check against the delivery list to ensure that the package contains the correct number and type of
accessories. If there is any discrepancy, contact the distributor immediately.
2.1.1
Installation Environment
NOTE
Operating the UPS in temperatures above 77°F (25°C) will reduce battery life.
The UPS environment must be free of conductive contaminants and excessive moisture (water and
condensation), flammable vapors, chemical fumes, corrosive gases and liquids.
2.1.2
Installation Tools
The tools required to properly set up your UPS are listed below:
•
•
•
•
•
•
2.1.3
Pallet jack
17mm (11/16") wrench or socket
13mm (1/2") wrench or socket
10mm wrench or socket
#1 and #3 Phillips screwdrivers
Torque wrench
Installation Site
Consider the weight and size of the Liebert APS when deciding where to install the unit. Verify that
the floor can support the weight of a fully loaded unit, any accessories and external cabinets.
Verify that the UPS will be in a well-ventilated area with at least 12 inches (305mm) clearance
behind it. The UPS is air-cooled, utilizing internal fans. Air is drawn into the front of the UPS and is
exhausted through ventilation grilles in the back. The UPS should also have at least 39 inches (1m)
clearance in front for service and to meet many local and national building codes.
Figure 13 Front and rear installation clearances
12in. (305mm)
39in. (1000mm)
15
Liebert® APS™
Installation
2.2
Unloading the UPS
The unit frame is bolted to the shipping pallet to ensure safety during shipping. Emerson
recommends keeping the unit bolted to the pallet and using a pallet jack to transport the unit to its
installation location.
NOTE
This UPS is very heavy. At least two people should assist in unloading it from the pallet.
To unload the UPS:
1. Move the UPS to its installation site and remove the package paper.
2. Use a 17mm (11/16") wrench, to remove the four mounting bolts from the pallet brackets (see
Figure 14).
3. Remove the mounting brackets from the UPS with a 10mm wrench or socket or a #3 Phillips
screwdriver.
Figure 14 Remove the mounting brackets
Mounting Bolts
(4 places)
Mounting Bracket
UPS
Pallet
Detail A
A
4. Raise the four leveling feet to provide clearance between the pallet and the UPS frame.
5. Connect the ramp to the UPS pallet, as shown in Figure 15.
6. Roll the UPS slowly down the ramp until it is on a level surface, as shown in Figure 15.
Figure 15 Connect the ramp and remove UPS
Liebert® APS™
16
Installation
2.3
Mechanical Installation
Two installation modes are available for the Liebert APS UPS: tower installation and rack
installation.
2.3.1
Tower Installation
1. Once the UPS is in the desired location, adjust the leveling feet to secure its position, as shown in
Figure 16.
a. Use an open end wrench to turn the lower nut to raise or lower the leveling foot.
b. After the unit is level, tighten the upper nut against the frame to prevent the height from
changing.
Figure 16 Adjust the leveling feet
Upper nut is threaded on
leveling foot; used to hold
foot height
A
Lower nut is bonded to
leveling foot; used to raise
and lower foot
Detail A
2. For added stability or earthquake-resistant installations, the shipping brackets can be used to
secure the unit to the floor.
a. Drill holes 10.3mm (13/32") in the floor for stationary mounting; these will accommodate the
mounting bolts removed from the pallet. Refer Figure 17 for the layout.
b. Use the mounting screws to install the mounting brackets on the front and rear of the UPS.
c. Secure the mounting brackets to the floor with the mounting bolts (see Figure 17).
For greater stability, use a higher-grade bolt.
Figure 17 Installation position and drilling hole dimensions for stationary mounting
716mm
(28.19")
Mounting Bolt
Mounting Bracket
M10
screw
Rear View
340mm
(13.39")
Floor-Mounting Hole Layout
17
Liebert® APS™
Installation
2.3.2
Rack Installation
1. Install the cage nuts on the corresponding positions in the rack, as shown in Figure 18.
a. Install cage nuts in the two lower square holes of 1U space and in the two upper square holes
of 2U space of all four rack posts. These cage nuts will secure the optional shelf that will
support the weight of the Liebert APS.
b. Install a cage nut in the middle square hole of 4U, 6U, 10U, 12U spaces, respectively, again in
all four posts. The cage nuts will help secure the UPS in the rack.
Figure 18 Install cage nuts
Floating Nut
Detail A
A
2. Install the rack-mount shelf on the corresponding position between 1U space and 2U space on the
bottom of the rack, as shown in Figure 19.
Figure 19 Install the tray
Screw,16 places
Tray
B
Detail B
3. Install the guide rails (ramp) in the mounting slot at the front of the tray, as shown in Figure 20.
Liebert® APS™
18
Installation
Figure 20 Install the guide rails
Detail C
Mounting Slot
Insert one end
of the guide rail
into the mounting
slot on the tray
Guide
Rail
C
4. Unscrew the 10 screws on the front of the two side panels of the UPS frame.
5. Use those screws to attach the brackets to each side of the UPS frame, as shown in Figure 21.
Figure 21 Install the brackets
Bracket
Screw
(8 places)
D
Detail D
Bracket
6. Push the Liebert APS frame slowly into the enclosure from the front, as shown in Figure 22. The
rear of the UPS goes into the rack first when installing through the front of the rack.
19
Liebert® APS™
Installation
Figure 22 Push the UPS frame into the rack
Front of Rack
Front of UPS
Push the
UPS frame
into the
rack.
Guide Rails
7. Use eight panel screws to secure the UPS frame to the rack posts, as shown in Figure 23.
NOTE
It might be necessary to use the leveling feet to get the holes to align
Figure 23 Fix the UPS frame
Panel Screw (8 Places)
Detail E
E
8. Use four screws to install the metal plate (accessory in the rack-mount kit) on the corresponding
position on the lower front part of the UPS frame
9. Insert the plastic bezel into the square holes of the metal plate, as shown in Figures 24 and 25.
Liebert® APS™
20
Installation
Figure 24 Install the metal plate
Square
hole
(2 places)
Metal
Plate
Screw
(4 places)
Detail F
F
10. The installation is complete, as shown in Figure 25.
Figure 25 Installation completed
Bezel
21
Liebert® APS™
Installation
2.4
Module Installation
The Liebert APS ships from the factory configured (modules prepopulated) and tested as a system to
the customer’s requirements. If any modules were removed to facilitate ease of installation, follow the
steps below to re-insert them properly.
2.4.1
Installing Power Module, Battery Module and Charger Module
1. Lift module to appropriate bay, resting end of module on bay shelf.
NOTE
Use caution not to rest the module on any of the plastic bezels, this could damage the bezel.
Two battery modules must be installed in the same row to complete the battery string.
2. Push the module into the bay slowly. The module will be locked until 1/3 is in.
a. At this point, lift the module up and continue pushing it until about 5cm of the module is still
out of the bay.
b. Push it firmly and smoothly to ensure that the module is fully inserted, as shown in
Figure 26.
Figure 26 Insert the power module, battery module and charger module
Step 2 a
Step 1
50mm
Step 2 b
3. Use a #2 Phillips screwdriver to install the module-securing bracket, and then press the lever
down into the bracket, as shown in Figure 27.
Liebert® APS™
22
Installation
Figure 27 Lever and fastener
Pull Out
Press
Downward
Before Pressing the Lever
Side View
After Pressing the Lever
Side View
NOTE
If the lever of the module cannot be pressed down smoothly, remove the module and reinstall it.
4. Replace the small plastic bezels.
2.4.2
Install System Control and System Monitor Modules
1. Remove the display bezel and the user interface (LCD) module on top of the frame, as shown in
Figure 28.
Figure 28 Remove large plastic bezel and user interface module
Display
Bezel
User
Interface
Module
2. Push the module slowly until about 1cm of the module is still out of the bay, and then press it
firmly to ensure that the module is fully inserted, as shown in Figure 29.
23
Liebert® APS™
Installation
Figure 29 Insert the System Control and System Monitor module
10mm
Insert
module
here
3. Use a #2 Phillips screwdriver to install the screws into the holes on each end.
4. Slide the lever toward the right, as shown in Figure 30.
Figure 30 Lever and fastener on System Control and System Monitor Module
Mounting
Hole
Mounting
Hole
Lever
Press and Slide
to the Right
Pull
Out Before Pressing
Lever
After Pressing
Lever
5. Replace the LCD module and display bezel.
Liebert® APS™
24
Installation
2.5
Cable Connection
! WARNING
Risk of electric shock. Can cause injury or death.
Disconnect local and remote power supplies before working within.
Read this section thoroughly before attempting to install wiring to this unit.
Ensure that all the UPS input sources are disconnected off before attempting to install wiring
to this unit.
This UPS cables should be connected by a properly trained and qualified electrician.
Refer to the unit model number in Table 2 to determine which instructions to use for installation.
Table 2
Cable connection method reference
UPS Model #
Digits 1-3
AS1 or ASA
2.5.1
Manual
Section
Frame Type
10 Bay Transformer-free
2.5.1
AS2 or ASB
16 Bay Transformer-free
2.5.1
AS3 or ASC
12 Bay Transformer-based
2.5.2
AS4 or ASD
16 Bay Transformer-based
2.5.2
AS5 or ASE
10 Bay Transformer-free
2.5.3
AS6 or ASF
16 Bay Transformer-free
2.5.3
Transformer-Free UPS Cable Connection
A junction box is factory-installed on each model of the Liebert APS to ease cable connection.
Select the appropriate input cables according to Table 3 and Table 4 based on the UPS rating and
mains frequency; however, it is recommended that you size the over current protection and wiring for
the frame rating to easily allow upgrades to the UPS system.
Table 3
Input cable selection list—60Hz
Input voltage - 200VAC
Input voltage - 208VAC
Input voltage - 240VAC
Maximum
System
Rated Load
Maximum
Current in
UPS Mode
Recommended
Input Protection
Circuit Breaker
Maximum
Current in
UPS Mode
Recommended
Input Protection
Circuit Breaker
Maximum
Current in
UPS Mode
Recommended
Input Protection
Circuit Breaker
5kVA
27A
50A
26A
50A
23A
50A
10kVA
53A
63A
51A
63A
45A
63A
15kVA
80A
100A
77A
100A
67A
100A
20kVA
106A
125A
102A
125A
90A
125A
2
The power input and output terminals accept a maximum cable cross-sectional area of 35mm (2AWG); the minimum cable
cross-sectional area is 16mm2 (6AWG); the rated torque is 4.52Nm (40 in-lb).
Use of 90°C copper wire is recommended
Table 4
Input cable selection list—50Hz
Input Voltage - 220VAC
Input Voltage - 230VAC
Input Voltage - 240VAC
Maximum Recommended Maximum Recommended Maximum Recommended
Maximum
System Rated Current in Input Protection Current in Input Protection Current in Input Protection
UPS Mode Circuit Breaker UPS Mode Circuit Breaker UPS Mode Circuit Breaker
Load
5kVA
25A
50A
24A
50A
23A
50A
10kVA
49A
63A
47A
63A
45A
63A
15kVA
73A
100A
70A
100A
67A
100A
20kVA
97A
125A
93A
125A
90A
125A
The power input and output terminals accept a maximum cable cross-sectional area of
cross-sectional area is 16mm2 (6AWG); the rated torque is 4.52Nm (40 in-lb).
90°C copper wire recommended
25
35mm2
(2AWG); the minimum cable
Liebert® APS™
Installation
To connect the cable:
NOTE
Input and output cables must be run in separate conduit before cable connection.
For the user whose input power grid is L-L line voltage, the input N of the power input and
output terminals will connect live wire, so the output N of the power input and output
terminals is also live wire.
1. Remove the knockouts at the junction box (see Figure 31) and pull the cables through them,
leaving some slack for installation.
Figure 31 Knockouts
10-Bay Liebert APS
No Transformer
16-Bay Liebert APS
No Transformer
2. Connect the cables to the corresponding terminal of the power input and output terminals.
3. Tighten the screws to 4.52Nm (40 in-lb) with a 13mm (1/2") torque wrench.
4. Respectively, secure the conduit of the input/output cables through the cable bridges on the rear
panel of the UPS (see Figure 31).
The connection methods in the single-phase input mode and the 3-phase input mode are shown in
Figures 32 and 33, respectively. Installation of the factory-provided copper bar is essential in the
single-phase input mode. The copper busbar is in the accessory bag included with the UPS.
Figure 32 Connection in single-phase input
OUTPUT
PE
2
INPUT
1
PE
4
3
2
200V/208V/220V/230V/240V
200V/208V/220V/230V/240V
Liebert® APS™
26
1
Installation
Figure 33 Connection in 3-phase input
OUTPUT
PE
2
INPUT
1
PE
4
200V/208V/220V/230V/240V
Table 5
3
2
1
380V/400V/415V
Key to Figures 32 and 33 UPS wiring
Input Terminal Block
Output Terminal Block
System
Voltage
System Nominal
Frequency
1
2
3
4
PE
1
2
PE
200
60
L1 *
L1 *
L1 *
L2
GND
L1
L2
GND
208
60
L1 *
L1 *
L1 *
L2
GND
L1
L2
GND
220
60
L1 *
L1 *
L1 *
L2
GND
L1
L2
GND
230
60
L1 *
L1 *
L1 *
L2
GND
L1
L2
GND
240
60
L1 *
L1 *
L1 *
L2
GND
L1
L2
GND
200
50
L*
L*
L*
N
PE
L
N
PE
220
50
L*
L*
L*
N
PE
L
N
PE
230
50
L*
L*
L*
N
PE
L
N
PE
240
50
L*
L*
L*
N
PE
L
N
PE
380
50
L1
L2
L3
N
PE
L
N
PE
400
50
L1
L2
L3
N
PE
L
N
PE
415
50
L1
L2
L3
N
PE
L
N
PE
*
This connection requires the factory-provided three-position busbar to connect the three terminal block positions
27
Liebert® APS™
Installation
2.5.2
Transformer-Based UPS Cable Connection
NOTE
After the output transformer is installed, if the startup is on bypass, the UPS has a six-cycle
inrush current that is up to 20 times the rated output current. This must be taken into account
when selecting the input overload protection device at the AC input supply distribution point.
To avoid random tripping on startup, Emerson® recommends that the AC input supply be
protected with a circuit breaker capable of withstanding this initial inrush (the MCB is
derated according to the D curve or TYPE 4).
This UPS is fitted with EMI filters. Earth leakage current is less than 40mA. Transient and
steady state earth leakage currents may occur when starting the UPS. This should be taken
into account when selecting transient RCCB or RCCD (leakage current devices of the UPS and
load).
The MCB of the AC power supply connected to the UPS input must bear this warning:
Disconnect the connection with UPS before maintaining this circuit
The warning is required because the UPS has no autofeeding protection device.
The UPS grounding should be in accordance with local regulations.
A junction box is factory-installed on all models of the Liebert APS to ease cable connection.
Select the appropriate input cables according to Table 6 and Table 7 based upon the UPS rating and
mains frequency. Emerson recommends sizing the frame’s overcurrent protection and wiring to
permit easier UPS system upgrades.
Table 6
Input cable selection for transformer-based frames (60 Hz)
Input Voltage - 200VAC
Input Voltage - 208VAC
Input Voltage - 240VAC
Maximum
Maximum Recommended Maximum Recommended Maximum Recommended
System Rated Current in Input Protection Current in Input Protection Current in Input Protection
Load
UPS Mode Circuit Breaker UPS Mode Circuit Breaker UPS Mode Circuit Breaker
5kVA
27A
50A
26A
50A
23A
50A
10kVA
53A
63A
51A
63A
45A
63A
15kVA
80A
100A
77A
100A
67A
100A
20kVA
106A
125A
102A
125A
90A
125A
2
The power input and output terminals accept a maximum cable cross-sectional area of 70mm (2/0AWG); the minimum cable
cross-sectional area is 16mm2 (6AWG). The rated torque is 12.43Nm (110 in-lb).
90°C copper wire recommended.
Table 7
Input cable selection for transformer-based frames (50 Hz)
Input Voltage - 220VAC
Input Voltage - 230VAC
Input Voltage - 240VAC
Maximum Recommended Maximum Recommended Maximum Recommended
Maximum
System Rated Current in Input Protection Current in Input Protection Current in Input Protection
UPS Mode Circuit Breaker UPS Mode Circuit Breaker UPS Mode Circuit Breaker
Load
5kVA
25A
50A
24A
50A
23A
50A
10kVA
49A
63A
47A
63A
45A
63A
15kVA
73A
100A
70A
100A
67A
100A
20kVA
97A
125A
93A
125A
90A
125A
2
The power input and output terminals accept a maximum cable cross-sectional area of is 70mm (2/0AWG); the minimum cable
cross-sectional area is 16mm2 (6AWG). The rated torque is 12.43Nm (110 in-lb).
90°C copper wire recommended.
Liebert® APS™
28
Installation
Configuring the Bypass Voltage
The UPS bypass voltage is factory-set to 208V (the jumper copper bar has been installed). Should the
user have a utility supply of 200V/220V/230V/240V, the bypass voltage jumper must be changed to
ensure correct output voltages when in bypass mode. Configuring the bypass voltage jumper settings
are shown in Figures 34 and 35. Refer to Table 9 for the proper setting according to the AC mains
voltage configuration.
Figure 34 Setting bypass voltage jumper (default: 208VAC)
Jumper
208V Tap
240V Tap
OUTPUT
PE GEC
4
3
2
1
1
2
3
INPUT
1
2
PE
208VAC
Figure 35 Setting bypass voltage jumper (200/220/230/240VAC)
Jumper
208V Tap
240V Tap
OUTPUT
PE GEC
4
3
2
1
1
2
3
INPUT
1
2
PE
240VAC
29
Liebert® APS™
Installation
Configuring the Neutral/Earth Jumper
The UPS contains an isolation transformer that generates a neutral conductor for the connected load.
The UPS is a separately derived source and contains a neutral/earth jumper. A factory-installed
neutral/earth jumper copper bar may require removal to comply with local codes and regulations.
Figure 36 Configuring the neutral/earth jumper
Neutral/Earth Jumper
208V Tap
240V Tap
OUTPUT
PE
GEC
4
3
2
1
1
2
3
INPUT
1
2
PE
Connecting Cables
To connect the cable:
NOTE
Input and output cables must be run in separate conduit before cable connection.
1. Remove the knockouts at the junction box (see Figure 37) and pull the cables through them,
leaving some slack for installation.
Figure 37 Knockouts
12-Bay Liebert APS
With Transformer
16-Bay Liebert APS
With Transformer
2. Connect the cable to the corresponding terminal of the power input and output terminals. Using a
torque wrench, tighten the screws to 4.52 Nm (40 in-lb). The connections are shown in Figure 38.
Liebert® APS™
30
Installation
Figure 38 Connection method
208V Tap
240V Tap
1
2
3
OUTPUT
PE GEC
4
3
2
1
1-3: 240V; 2-3: 208V; 1-4: 120V;
3-4: 120V (When the output voltage is
set to 240V through LCD )
INPUT
1
2
PE
200V/208V/
220V/230V/240V
Factorysupplied
jumper
Refer to Table 7 for configuring the output cable. For standard voltages, make the connections shown
in Table 9.
Table 8
Key to Figure 38 UPS input wiring
System
Voltage
System
Nominal
Frequency
200
208
220
230
240
200
220
230
240
60
60
60
60
60
50
50
50
50
Table 9
Input Terminal Block
1
2
PE
L1
L1
L1
L1
L1
L
L
L
L
L2
L2
L2
L2
L2
N
N
N
N
GND
GND
GND
GND
GND
PE
PE
PE
PE
Key to Figure 38 UPS output wiring
Output
Voltage
Set Output
Voltage
by LCD
200/100
Bypass Voltage Jumper
Output Voltage (Between Terminals)
208V TAP
(1-2)
240V TAP
(2-3)
1-4
3-4
200
—
OK
100
100
220/110
220
—
OK
110
110
230/115
230
—
OK
115
115
220/127
220
OK
—
127
127
220
240/120
208/120
240
208
—
OK
OK
—
120
120
120
120
208
208
2-3
1-3
173
(Do Not Use)
190
(Do Not Use)
199
(Do Not Use)
200
220
230
254
(Do Not Use)
240
240
If the bypass voltage jumper copper bar is connected incorrectly, the system will report a fault alarm.
When wiring to single-phase panels, connect to output terminals 1, 3, 4 and PE (GND) only.
Table 10 shows the maximum load capacity of the output winding of the transformer-based UPS.
Table 10
Maximum load capacity of the output winding
Maximum Output Capacity, kVA
(Between Terminals)
UPS Model
1-4
3-4
2-3
1-3
16-bay Transformer-based UPS
10
10
20
20
10-bay Transformer-based UPS
7.5
7.5
15
15
31
Liebert® APS™
Installation
2.5.3
Transformer-Free UPS—Dual Inverter Frames
A junction box is factory-installed on all models of the Liebert APS to ease cable connection.
Select the appropriate input cables according to Tables 11 and 12 based on the UPS rating and
mains frequency. Emerson recommends sizing the overcurrent protection and wiring for the frame
rating for easing upgrades to the UPS system.
Table 11
Input cable selection for Transformer-free Dual Inverter frames(50/60 Hz)
Input Voltage – 200/100VAC
Input Voltage – 208/120VAC
Input Voltage – 240/120VAC
Maximum
Maximum Recommended Maximum Recommended Maximum Recommended
System Rated Current in Input Protection Current in Input Protection Current in Input Protection
Load
UPS Mode Circuit Breaker UPS Mode Circuit Breaker UPS Mode Circuit Breaker
5kVA
28A
50A
27A
50A
27A
50A
10kVA
56A
63A
54A
63A
54A
63A
15kVA
84A
100A
80A
100A
80A
100A
20kVA
112A
125A
107A
125A
107A
125A
The power input and output terminals accept a maximum cable cross-sectional area of 35mm2 (2AWG); the minimum cable
cross-sectional area is 16mm2 (6AWG); and the rated torque is 4.52Nm (40 in-lb);.
90°C copper wire is recommended.
Table 12
Input cable selection for Transformer-free Dual Inverter frames(50/60 Hz)
Input Voltage – 220/110VAC
Input Voltage – 230/115VAC
Input Voltage – 220/127VAC
Maximum
Maximum Recommended Maximum Recommended Maximum Recommended
System Rated Current in Input Protection Current in Input Protection Current in Input Protection
Load
UPS Mode Circuit Breaker UPS Mode Circuit Breaker UPS Mode Circuit Breaker
5kVA
28A
50A
28A
50A
27A
50A
10kVA
56A
63A
56A
63A
54A
63A
15kVA
84A
100A
84A
100A
80A
100A
20kVA
112A
125A
112A
125A
107A
125A
The power input and output terminals accept a maximum cable cross-sectional area of 35mm2 (2AWG); the minimum cable
cross-sectional area is 16mm2 (6AWG); and the rated torque is 4.52Nm (40 in-lb);
90°C copper wire is recommended.
To connect the cable:
NOTE
Input and output cables must be run in separate conduit before cable connection.
1. Remove the knockouts at the junction box (see Figure 31) and pull the cables through them,
leaving some slack for installation.
Figure 39 Knockouts
10-Bay Liebert APS
No Transformer
16-Bay Liebert APS
No Transformer
2. Connect the cables to the corresponding terminal of the power input and output terminals.
3. Tighten the screws to 4.52Nm (40 in-lb) with a 13mm (1/2 in) torque wrench.
Liebert® APS™
32
Installation
4. Respectively secure the input/output cables through the cable bridges on the rear panel of the
UPS (see Figure 40).
Figure 40 Secure cables on cable bridges
The connections for the single-phase input mode and the 3-phase input mode are shown in Figure 32
and Figure 33, respectively. The copper jumper busbar is essential for the single-phase input mode.
Figure 41 Wiring connections
PE
OUTPUT
N
L2
L1
PE
33
INPUT
N
L2
L1
Liebert® APS™
Installation
2.5.4
Connecting External Battery Cabinet
Up to four external battery cabinets may be connected to the Liebert APS to provide longer battery
run times.
An external battery cabinet contains a standard battery cable and a communication cable, each
1meter (39in) long. They are used to connect UPS and the external battery cabinet. Optional cables of
3 and 5 meters can be provided if the battery cabinets must be located some distance from the UPS
cabinet.
To connect an external battery cabinet:
1. Connect one end of the battery cable to the external battery connector on the rear of the UPS.
2. Connect the other end to the corresponding port on the rear of the external battery cabinet, as
shown in Figure 42 and Figure 43.
3. Install and tighten a grounding screw between the EBC battery cable and the UPS frame.
4. Insert a Liebert IntelliSlot EBC card into any intelligent card slot on the rear of UPS. Connect
one end of the signal cable to the Liebert IntelliSlot EBC card and the other end to the Liebert
IntelliSlot EBC card on the rear of the external battery cabinet, as shown in Figure 42 and
Figure 43.
Figure 42 Connecting external battery cabinet to a transformer-free UPS
Communication
Cable
Battery
Cable
Liebert APS
Liebert® APS™
Battery Cabinet
34
Installation
Figure 43 Connecting external battery cabinet (transformer-based UPS)
Communication
Cable
Battery
Cable
Liebert APS
Battery Cabinet
After connecting the external battery cabinet, use the user interface to determine the number of
external battery cabinets, as shown in Figure 44.
Figure 44 Battery screen
Liebert APS
Batt temp (e
C)
Discharge count
Discharge hour (H)
Ext batt-cab count
2012-01-01
10:45:20
25.0
303
9.4
0
Ʒ
Ʒ
Battery
ESC
If the number displayed is not consistent with the actual installation number of external battery
cabinets:
• Ensure each external battery cabinet contains two battery modules installed on the same row and
both have the locking levers in the locked position.
• Ensure the Liebert IntelliSlot EBC card is installed properly and the communication cables are
fully inserted in the connectors.
• Determine that the DIP switch setting of each battery cabinet is correct using the following table
Table 13
EBC DIP switch settings
External Battery
Cabinet Number
DIP Switch Setting
1
2
EBC #1
UP
UP
EBC #2
Down
UP
EBC #3
UP
Down
EBC #4
Down
Down
35
Liebert® APS™
Installation
2.5.5
Connecting Integrated Power Output Distribution (POD)
The rear panel of the Liebert APS UPS provides the capability to add integrated distribution outlets
(PODs) as an option to allow direct AC power connection of the supported equipment to the UPS.
These PODs are intended to allow the user to install and even change distribution, if necessary as
equipment changes, while the UPS is still providing power. Follow these steps to properly and safely
add or change the optional PODs.
1. Ensure that the POD breaker is in the Off position.
NOTE
This is the breaker located near the POD port.
2. Using a Phillips screwdriver, remove the two screws that are at the top of the POD cover plate
and retain these for reattaching the POD.
3. Remove the POD cover plate to expose the POD connectors.
4. Insert the bottom of the POD into the slot provided, and then connect the POD connectors.
NOTE
The two connectors should connect only one way, matching the color of the connectors.
NOTE
Distribution PODs PD2-101, PD2-102, PD2-103, PD2-104, PD2-105, PD2-106 and PD2-107
should not be used if the UPS output voltage is set to 220/127V.
5. Secure the POD by using the two screws removed in Step 2.
6. Repeat Steps 1 through 5 to install a second POD on the Liebert APS (only the 16-bay frame has
two POD ports).
7. Connect the equipment to the appropriate outlets.
8. Close the POD breaker(s) to connect AC power to the outlets.
9. After commissioning the UPS, turn On the connected equipment per the manufacturer’s
instructions (see 2.5.6 - Commissioning/Startup Procedures).
2.5.6
Commissioning/Startup Procedures
The Liebert APS can be commissioned with or without AC power being connected. Follow these steps
for the initial UPS system startup:
Checks Before Commissioning/Startup
___ 1. Verify that the AC power connections are wired properly and all connections are tight.
___ 2. If using external battery cabinets or third-party battery systems, verify that the DC power
and communication cables are connected properly and all connections are tight.
___ 3. Measure and record the AC input voltage and frequency. This will be needed to properly
configure the output voltage of the Liebert APS system.
___ 4. If any modules within the Liebert APS system were removed during installation, verify that
all modules are fully inserted and that the module locking levers are in the locked position.
___ 5. If the UPS is being connected into a Remote Emergency Power Off (REPO) circuit, refer to
3.3 - REPO (Remote Emergency Power Off) for the REPO connection details and
instructions. If no REPO circuit is required or used, the factory-installed jumper must be
removed from the terminal block Pins 9-10 as described in 3.2 - Dry Contact Ports.
___ 6. Verify that the UPS internal bypass breaker is in the open position with the guard in place
and secure.
Liebert® APS™
36
Installation
Commissioning/Startup with AC Power Available (Normal Mode Operation)
___ 1. Verify that the upstream mains AC breaker is closed.
___ 2. Turn On the UPS Enable switch on the rear of the unit (it is protected by a clear plastic
cover).
___ 3. Close the UPS input breaker: it is on the front of transformer-free frame systems and on the
rear of transformer-based frame systems.
NOTE
This will begin the initial system checks and enable power to begin charging the battery
___ 4. Press the ON/OFF button on the LCD panel.
___ 5. When asked to confirm, press Enter (F5 button) to turn On the UPS.
___ 6. Close the UPS output breaker on the rear of the unit.
___ 7. If supplying power to an external distribution panel, close all breakers to provide power to the
equipment. If using the integral distribution PODs on the UPS or MBC, ensure the individual
POD breakers are closed.
Commissioning/Startup Without AC Power Available (Battery Mode Operation)
NOTE
Starting the UPS system without AC power will discharge the batteries. If AC mains power is
not restored before the batteries discharge, the USP will shutdown and power will be lost to the
connected equipment. If the UPS reaches the battery EOD level and shuts down, AC mains
power must be present to restart the UPS system.
1. Check to ensure the upstream mains AC breaker is closed.
2. Turn on the UPS “Enable” switch on the rear of the unit.
3. Locate the “Battery Start” push button that is on either of the two control modules. Press and
hold this button for 5 seconds.
NOTE
This will begin the initial system checks and automatically enable output power.
4. Close the output breaker on the rear of the Liebert APS.
5. If supplying power to an external distribution panel, close all breakers to provide power to the
equipment. If using the integral distribution PODs on the UPS or MBC, verify that the individual
POD breakers are closed.
6. Emerson recommends closing the UPS input breaker; it is on the front of transformer-free frame
systems and on the rear of transformer-based frame systems. If AC mains becomes available, the
UPS will revert to AC power mode and begin recharging the battery.
37
Liebert® APS™
Communication
3.0
COMMUNICATION
The rear panel of the Liebert APS provides these communication ports:
•
•
•
•
•
3.1
Liebert IntelliSlot® ports—3
Dry contact ports—1
REPO (Remote Emergency Power Off)—1
Long Run Time (LRT) Battery Temperature Probe Terminals—1
USB port—1
Liebert IntelliSlot Ports
The three Liebert IntelliSlot communication ports (see Figure 45) are used for installing
communication options, including the Liebert IntelliSlot Unity card, dry contact card, Liebert
MultiPort and Liebert IntelliSlot EBC card. The Liebert IntelliSlot ports and the USB port can be
used at the same time.
Figure 45 Liebert IntelliSlot communication port location
Liebert
IntelliSlot
Ports
Liebert IntelliSlot Ports
(with protective covers)
Liebert IntelliSlot Unity Cards—IS-UNITY-LIFE, IS-UNITY-S, IS-UNITY-DP
• IS-UNITY-LIFE: This card is standard in every Liebert APS. It is used for communication
between the Liebert APS UPS and Emerson’s Trellis® NMS and LIFE Services.
• IS-UNITY-S: This optional card can be used instead of the standard card if communication to a
third party platform is required. Third-party platforms include SNMP or 485 (Modbus/Bacnet)
protocols. This card would still be used for communication between the Liebert APS and
Emerson’s Trellis NMS and LIFE Services. All communication protocols are active
simultaneously.
• IS-UNITY-DP: This optional card can be used instead of the standard card if communication to
two third-party platforms is required. Third-party platforms include SNMP and 485
(Modbus/Bacnet) protocols. This card would still be used for communication between the Liebert
APS UPS and Emerson’s Trellis NMS and LIFE Services. All communication protocols are active
simultaneously.
Liebert® APS™
38
Communication
Liebert IntelliSlot® Dry Contact Card (IS-RELAY)
Provides dry contact alarm information, including: On Battery, On Bypass, Low Battery, Summary
Alarm, UPS Fault and On UPS signals for communication to a remote monitoring system or for use
with Liebert MultiLink® software. This card also can accept input signals to shut down the UPS while
it is in any mode of operation.
Liebert IntelliSlot MultiPort Card (IS-MULTIPORT)
Provides dry contact alarm information, including: On Battery, Low Battery signals for
communication to four servers for use with Liebert MultiLink software.
Liebert IntelliSlot EBC Card
This card is used for the Liebert APS UPS to monitor and manage the intelligent battery modules in
external matching battery cabinets.
3.2
Dry Contact Ports
The UPS provides dry contact ports. See Figure 1 for location and Figure 46 for the pin layout.
Figure 46 Pin layout of the dry contacts
1
2
3
4
5
6
7
8
Table 14 shows the pin definition of each dry contact port.
Table 14
Position
Pin definition of dry contact port
Name
Description
1
Battery Mode
Output dry contact of battery mode operation
2
Battery Mode
Output dry contact of battery mode operation
3
Low Battery
Output dry contact of low battery operation
4
Low Battery
Output dry contact of low battery operation
5
Any Mode Shut Down
Input dry contact of any mode shut down
6
GND
Any mode shutdown GND
7
Battery Mode Shut Down
Input dry contact of battery mode shut down
8
GND
Battery mode shutdown GND
Battery Mode Dry Contact
Pins 1 and 2: Output dry contact, normally open. The dry contact is closed when the UPS is
operating on battery. The maximum voltage and current are 24VDC and 0.3A, respectively.
Low Battery Dry Contact
Pins 3 and 4: Output dry contact, normally open. When the UPS is operating on battery, the dry
contact is closed upon battery low voltage alarm. The maximum voltage and current are 24VDC and
0.3A, respectively.
39
Liebert® APS™
Communication
Any Mode Shut Down
Pins 5 and 6: Input dry contact, normally open. After the external dry contact is closed (shorted), the
UPS output will be shut down during any mode of operation (mains, battery, bypass).
Battery Mode Shut Down
Pins 7 and 8: Input dry contact, normally open. After the external dry contact is closed (shorted), the
UPS output will be shut down only during battery mode operation.
NOTE
The default for the Any Mode and Battery Mode Shutdown features is disabled. Using this
function requires setting Remote Comms shutdown to Enabled in the Settings through the
LCD. Additionally, the shutdown delay can be accessed in the LCD Settings to set the delay
time for the UPS shutdown after the dry contact is closed. Enabling the feature on the LCD
enables both shutdown methods.
3.3
REPO (Remote Emergency Power Off)
The Liebert APS is equipped with a REPO (Remote Emergency Power Off) connection. Only the SELV
(Safety Extra Low Voltage) circuit can be connected to the REPO terminal block. Figure 48 shows
the REPO connection pin layout. See Table 15 for the pin definition.
Figure 47 REPO connector pin layout
9
10
11
12
Table 15
Position
Pin definition of the REPO dry contact
Name
Description
9
REPO +12V
REPO power, 12VDC 100mA
10
REPO Coil -NO
REPO normally open nodes, shorting pins 9 and 10, REPO is triggered
11
REPO Coil -NC
REPO normally closed nodes (fail-safe), shorting pins 9, 10, 11, 12, and opening
pins 11 and 12, REPO is triggered
12
GND
GND
Figure 47 shows the schematic diagram of REPO switch connections.
Figure 48 REPO switch connections
During Shipping
9
Liebert® APS™
10
11
For Normally Open System
12
9
10
11
40
12
For Normally Closed System
(fail-safe)
9
10
11
12
Communication
! WARNING
Risk of electrical shock. Can cause property damage, injury and death.
Operating the REPO circuit will NOT trip the manual bypass breaker. If the REPO must shut
off UPS output under all circumstances, the user must tie the REPO into the breaker feeding
the UPS source. Otherwise, voltage may be present on the output connections if the unit is in
manual bypass.
NOTICE
Risk of improper installation. Can cause unintended UPS shutdown and loss of power to the
load.
Run signal cables separately from power cables. Running cables in the same conduit can
cause signal noise, possibly causing the system to shut down.
NOTE
A jumper is factory-installed between Pins 9 and 10 to disable the Main Control Switch. This
will prevent the UPS from being started accidentally during shipment and installation. This
jumper must be removed before the unit can be started.
If the installation does not require connection to a REPO system, the factory-installed jumper
must be removed.
3.4
Long Run Time (LRT) Battery Temperature Probe Terminals
The Liebert APS contains a temperature-compensated battery charging system. To use this feature
with external LRT battery systems, Pins 13-16 of the contact terminal strip are used to connect a
temperature sensor. See Figure 49 and Table 16 for the pin definition of the temperature sensor
terminals.
Figure 49 Pin layout of the temperature sensor terminal
13
14
15
16
Table 16
Pin definition of the temperature sensor terminal
Position
13
3.5
Name
Description
Inside Battery Temperature
Locate battery temperature signal close to the UPS
14
Battery Temperature +12V
Battery temperature signal power supply
15
Outside Battery Temperature
Locate battery temperature signal at UPS remote end
16
GND
GND
USB Port
The Liebert APS UPS contains a standard B type USB port on the rear of the unit to connect the UPS
to a network server or other computer for monitoring using any operating system, built-in UPS
support or in conjunction with Liebert MultiLink® software.
41
Liebert® APS™
Communication
3.6
Liebert MultiLink®
Liebert MultiLink monitors the UPS continuously and can shut down configured computers in the
event of an extended power failure. Liebert MultiLink can also be configured to shut down the UPS.
Liebert’s MultiLink can also be configured for use without the USB cable when the Liebert
IntelliSlot® UNITY-S or UNITY-DP SNMP Card is installed in the UPS. An optional Liebert
MultiLink License Kit permits shutting down the UPS over a network. For more information about
the Liebert IntelliSlot SNMP Card, Liebert IntelliSlot Web Card and Liebert MultiLink license kits,
visit http://multilink.liebert.com or contact your local Emerson representative.
3.7
LCD Port
The LCD module contains the LCD port, which is used for power and data communication between
the UPS monitor module and display module. The LCD module can be removed from the Liebert APS
and remotely located. A longer Ethernet cable must be used when installing the LCD module
remotely. A standard Ethernet (Category 5, with RJ-45 connectors, both ends meet T568B standard)
type cable can be used. Maximum cable length is 14 meters to ensure proper communication signals
between the UPS and the LCD module.
The user interface module provides three network ports and one USB port. Of those, one network port
(LCD port) is used for power supply and communication of the user interface module. Other network
ports and the USB port are reserved for use only by customer service personnel.
Figure 50 LCD port
LCD Port
User Interface
Module
Liebert® APS™
42
Operation and Display Panel
4.0
OPERATION AND DISPLAY PANEL
4.1
Overview
This chapter describes the functions and operation of the UPS display panel. The LCD is composed of
an LED mimic power flow diagram, fault LED indicator and LCD screen to show detailed operational
information and UPS alarm list using the navigation buttons. For location and information about the
display panel, refer to Figure 51 below
Figure 51 Operation and display panel
Bypass LED Output LED LCD
Inverter LED
On/Off button
Fault LED
AC LED
Alarm Silence
Battery LED
Menu Buttons
Mimic LEDs
The mimic power flow LEDs indicate current operating state of the UPS. The state descriptions of the
LEDs are given in Table 17.
Table 17
LED descriptions
LED
State
On (Green)
AC LED
Battery LED
Bypass LED
Inverter LED
Output LED
Fault LED
Description
The rectifier is functioning normally
Flashing (Green)
The AC mains is normal, but the rectifier is not functioning properly
On (Red)
The rectifier is faulty
Off
The AC mains is abnormal, and the rectifier is not functioning
On (Green)
The battery is discharging
Flashing (Green)
The battery has a pre-alarm of low voltage
On (Red)
The DC-DC converter is faulty
Off
The battery is charging, and the DC-DC converter is not functioning
On (Green)
The bypass is supplying power
On (Red)
The bypass is abnormal and not available
Off
The bypass is normal, but not supplying output power
On (green)
The inverter is supplying output power
Flashing (green)
The inverter is starting up, in soft start or phase locked, and is not supplying
output power
On (red)
The inverter is faulty
Off
The inverter is off
On (green)
The UPS output is supplying power
Flashing (green)
The UPS internal manual bypass is supplying output power
On (red)
The UPS has output overload
Off
The UPS does not have output power
On (yellow)
The UPS has an alarm or alarms
On (red)
The UPS has one or more faults
Off
UPS operating normally with no alarm or fault conditions
43
Liebert® APS™
Operation and Display Panel
Audible Alarms
Three different audible alarms may occur during the UPS operation; see Table 18 for a description of
the audible alarms.
Table 18
Audible alarm descriptions
Alarm sound
Meaning
One beep per second
When the UPS has an alarm, for example, AC fault (mains failure)
One beep every 0.5 second
Upon UPS output overload or low battery voltage alarm during discharge
Continuous beep
When the UPS has a fault
Control Buttons
The operation and display panel provides two control buttons. See Table 19 for their function
descriptions.
Table 19
Control buttons functions
Control Button
Function
ON/OFF Button
Used to turn the UPS On and Off.
Alarm Silence Button
When an audible alarm sounds, pressing this button can silence the alarm. Pressing this
button again can restart the audible alarm.
LCD and Menu Buttons
The operation and display panel provides an LCD screen and five menu buttons (F1, F2, F3, F4, F5).
See Table 20 for the function description of each menu button.
Table 20
Function descriptions of menu button
Button
F1
Function 1
F2
F4
F5
To Left
To Right
Enter
—
HOME
Function 2
F3
—
ESC Exit
—
Up
Down
The LCD is a 320 × 240 dot matrix graphic display. Through the LCD interface and the easily
operated menu, you can browse the UPS input, output, load and battery parameters and obtain the
current state and alarm information of the UPS. You also can perform relevant function/parameter
settings and control operations.
Figure 52 User interface module layout
Bypass LED Output LED
LCD
On/Off Button
Inverter
LED
Fault LED
AC LED
Alarm
Silence
Button
Battery
LED
Liebert® APS™
44
Operation and Display Panel
4.2
LCD Screen
4.2.1
Startup Screen
When the UPS starts up, it will conduct a self-test, and the LCD will display the startup screen,
which lasts for 15 seconds as shown in Figure 53.
Figure 53 Startup screen
4.2.2
Main Screen
The main screen is divided into four parts: system information window, data window, menu window
and keyboard window, as shown in Figure 54.
Figure 54 Main screen
Liebert APS
L-N Voltage (V)
L-N Current (A)
Frequency (Hz)
Power Factor
2013-03-22
3:22:00
220.0
90.9
50.0
0.99
Information Window
Data Window
Mains
Menu Window
Keyboard Window
The functions of F1 ~ F5 buttons will change automatically according to the currently-displayed
screen. On any screen, pressing the F1 button will return to the Output screen.
System Information Window
The system information window displays the current time and the UPS name without requiring user
intervention. See Table 21 for the detailed description.
Table 21
Item description of system information window
Item
Description
Liebert APS
UPS name, representing Liebert APS
2012-01-01
10: 45: 20
Current time (format: year-month-date)
(format: 24 hours, h: m: s)
45
Liebert® APS™
Operation and Display Panel
Menu Window and Data Window
The menu window shows the menu name and allows navigation to different menu items. Each menu
item has a set of data that is displayed in the data window. Using the menu window, you can browse
the relevant parameters of the UPS and can adjust/set some operational parameters. See Table 22
for the menu and data descriptions.
Table 22
Item description of menu window and data window
Menu Name
Mains
Battery
Output
Load
Data Item
L-N Voltage (V)
L-N Current (A)
Frequency (Hz)
L-L Voltage (V)
kVA
Power Factor
Batt Voltage (V)
Batt Current (A)
Runtime (Min.)
Batt Capacity (%)
Batt State
Batt String Count
Batt Temp (°C)
Discharge Count
Discharge Time
(H)
EBC Count
L-N Voltage (V)
L-N Current (A)
Frequency (Hz)
Power Factor
Line Voltage (V)
kVA
kW
Load Level (%)
Crest Factor
UPS ID
LCD Module
UPS Info
Bypass Monitor
Module
Bypass Control
Module
Charger Module
Power Module
Battery Module
Redundant
State
Liebert® APS™
PM Installed
PM
Data Description
L-N input voltage
L-N input current
Input frequency
L-L input voltage
Input apparent power
Input power factor
Battery bus voltage
Battery bus current
Battery backup time remaining
Percentage of battery capacity
Charging, discharging or fully charged
Online battery string count
Battery temperature
Maximum historical discharge count within current battery modules
Maximum historical discharge time within current battery modules
Number of connected External Battery Cabinets
L-N Output Voltage
L-N Output Current
Output Frequency
Output Power Factor
L-L Output Voltage (not displayed for single-phase output model)
Output apparent power
Output active power
Output loading, indicated in percentage of the UPS system rated load
Output current peak value factor
UPS ID
If the module is online, the serial number and software version will be
displayed
If the module is online, the serial number and software version will be
displayed
If the module is online, the serial number and software version will be
displayed
If the module is online, the serial number and software version will be
displayed
If the module is online, the serial number and software version will be
displayed
If the module is online, the serial number and software version will be
displayed
The number of installed power modules
Whether there are redundant power modules supplying power.
46
Operation and Display Panel
Table 22
Item description of menu window and data window (continued)
Menu Name
Data Item
Set Redundancy
Mode
Remote Comms
Shutdown
Bypass Setting
Output Frequency
Output Voltage
Inverter Sync
Range
Remote Shutdown
Delay
Bypass Upper
Limit
Bypass Lower
Limit
Settings
Data Description
Disabled/ Enabled. If ‘Enabled,’ the system operational parameters will
assume there is a redundant power module in the frame; if ‘Disabled’, the
system operational parameters will assume that all power modules in the
frame are not redundant.
Note: This item is closely related to the ‘Redundant alarm’ setting
Disabled/ Enabled. If ‘Enabled,’ this allows the UPS output power to be
shutdown through remote communication, including the dry contacts and
Liebert IntelliSlot communication cards.
Note: This item is closely related to ‘Remote shutdown delay’
Enables the bypass to supply power or not
Sets the output frequency to allow frequency conversion operation
Sets the output voltage level to match the mains input voltage
Sets the range of inverter synchronization for bypass frequency operation
and availability
Sets the shutdown delay time for the remote signal operation
Sets the upper limit of bypass voltage operation and availability
Sets the lower limit of bypass voltage operation and availability
Guaranteed
Shutdown
Disabled/ Enabled. If ‘Enabled,’ once a low battery alarm is generated
during a battery discharge, the UPS will continue battery mode operation
until it reaches the end of discharge (EOD) setpoint, then will shutdown
output power, whether the AC mains recovers or not.
Bypass Alarm
Mode
Allows an alarm to be generated when the bypass is abnormal
Set RS232
Protocol
Auto-Restart Mode
Auto-Restart
Capacity
Auto-Restart Delay
Display Contrast
Date and Time
Command
Password
Max Load Alarm
Max Load
Threshold
Redundant Alarm
Mode
Because the slot 2 and the serial port on the rear panel cannot work at the
same time, you must select one of them to work. If ‘INTERFACE2’ is
selected, the slot 2 can communicate; if ‘RS232’ is selected, the serial
port can communicate.
Allows auto restart after a EOD shutdown and AC mains returns
Sets the battery capacity limit of auto restart feature. When AC mains
power returns, the UPS will charge the battery to the specified battery
capacity before enabling output power.
Sets the delay time of auto restart feature. When AC mains power returns,
the UPS will start a countdown timer based upon the setting before
enabling output power.
Adjusts the contrast of LCD backlighting
Sets date and time
Users can change the command password to prevent unauthorized user
from changing any user configurable settings. The default password is
1234567. Once the password is changed, the default password is no
longer operational and users are then required to enter the new password
to enter/change any ‘Settings’ or ‘Battery settings’. If the new password is
forgotten, contact your local customer service center for steps to reset the
password back to the factory default.
Sets a maximum load alarm. This item is closely related to ‘Max load
threshold.’
Sets the threshold of maximum load alarm. When the UPS loads exceed
the threshold, and the maximum load alarm is enabled, an alarm will be
generated.This item is closely related to ‘Max load alarm,’ for example, set
this item to 5.0kVA, when the UPS loads exceed 5.0kVA, an alarm will be
generated.
Allows alarm to be generated when the system loses redundant power
module
47
Liebert® APS™
Operation and Display Panel
Table 22
Item description of menu window and data window (continued)
Menu Name
Data Item
Communication
Address
Air Filter Reminder
Air Filter Type
Settings
(continued)
IT System
Compatibility
UPS ID
Company Name
Contact Number
Load factory
defaults
Low battery
Warning
Automatic Battery
Test Interval
Battery settings
Auto Batt Test
Start Day
Auto Batt Test
Start Time
External Battery
AH
Load Factory
Defaults
Language
Language Options
Alarms
Records
Current Alarms
Historical Alarms
LCD Module
Bypass Monitor
Module
Bypass Control
Module
Power Module
Battery Module
Charger Module
Module
replacement
Liebert® APS™
Data Description
Sets the UPS device address. This setting is only for the network card
communication of newly emerging market.
Set the reminder period of checking dust-proof filter
Standard: Use this setting if air filter is not installed.
Fine Dust: Use this setting if air filter is installed.
Enabled - Neutral back-feed relay will open on battery mode
Disabled (Default) - Neutral back-feed relay is always closed
Users can set the UPS name to facilitate managing the UPS through
remote communications
Set the local service company name of the UPS
Set the local service telephone number of the UPS
Restores the setting items in ‘Settings’ menu to factory values
Sets the battery low voltage alarm time
Sets the interval for the automatic battery test. Intervals of 8, 12, 16, 20,
26 weeks or Disable are available for selection. Factory default is 8
weeks.
Sets the day of the week for the automatic battery test
Sets the time of the day for the automatic battery test
Sets the AH capacity of external third party battery system to calculate the
battery capacity and estimate the battery time remaining
Restores the setting items in ‘Battery set’ menu to factory values
Provides a selection of seven languages:
Chinese, English, French, Spanish, Italian, Russian and German
Displays the current alarms. See Table 25 for the UPS alarm list
Displays all historical alarms. See Table 25 for the UPS alarm list
Displays the procedures for replacing LCD module
Displays the procedures for replacing system monitor module
Displays the procedures for replacing system control module
Displays the procedures for replacing power module
Displays the procedures for replacing battery module
Displays the procedures for replacing charger module
48
Operation and Display Panel
Table 22
Item description of menu window and data window (continued)
Menu Name
Data Item
Battery
Maintenance Test
Stop Battery Test
System Test
Stop Testing
Freshening Charge
Stop Freshening
Charge
Data Description
Battery maintenance test allows battery to discharge some voltage to
obtain the battery activity. The loads must be within 0% ~ 90%, the battery
capacity must be larger than 70%, and there is no battery fault and alarm
in the system.
Stops battery maintenance test
A UPS self-test, used to test whether the LEDs are normal. When you
start this function, 5 seconds later, the screen will prompt a window to
display the system self-test result.
Stops system test manually
Boost charges the battery by force, manually
Stops freshening charge manually
Allows customer service personnel to set the UPS ID, to facilitate
maintenance
Allows customer service personnel to set the UPS address, to facilitate
Site ID
maintenance
Allows customer service personnel to set the UPS tag, to facilitate
Tag Number
Service
maintenance
Allows customer service personnel to set the UPS company name, to
Company Name
facilitate maintenance
Allows customer service personnel to set the UPS company contact
Contact Number
number, to facilitate maintenance
Reset this when replacing the LCD board. The frame S/N is labeled on the
Frame S/N
frame.
Allows customer service personnel to set the UPS operating mode to
Normal Mode
normal online mode
Allows customer service personnel to set the UPS operating mode to
ECO Mode
ECO mode
Enable Max
By default, the UPS has a maximum discharge time to protect the
Discharge
batteries from a deep, slow discharge. After this time, the UPS will turn Off
Protection
its output.
If this variable is set, there will be no time limit and the UPS will stay on
Disable Max
battery until the EOD setpoint is reached. This may cause damage to
Discharge
some battery types and should only be used for DC sources that do not
Protection
have slow discharge issues.
The Service screen is only for customer service personnel; it is not open to the user.
UPS ID
Keyboard Window
For the functions of the menu buttons (F1 ~ F5) in the keyboard window, see Table 23
Table 23
Function descriptions of menu buttons
Button
F1
Function 1
F2
F4
F5
To Left
To Right
Enter
—
HOME
Function 2
F3
—
ESC Exit
—
Up
49
Down
Liebert® APS™
Operation and Display Panel
4.2.3
Default Screen/Screen Saver
During the UPS operating process, if there are no active alarms, the LCD will go into a screen saver
mode after 2 minutes of no user navigation activity. The default screen saver is shown in Figure 55.
After a brief delay, the LCD backlight will also turn Off. Pressing any button will return to the
original screen.
Figure 55 Default screen/screen saver
4.3
LCD Screen Views
This section gives a detailed description of each display screen and its contents. The default “main
screen” is the Output menu and its data. The navigation indicated for each screen below is in
reference to the Output screen.
4.3.1
AC Mains Screen
From the main screen, press the F3 button twice, until the AC mains screen is displayed, as shown in
Figure 56.
Figure 56 Mains screen
2014-01-01
10:45:20
Liebert APS
L-N Voltage (V)
L-N Current (A)
Frequency (Hz)
L-L Voltage (V)
kVA
Power Factor
L1
220.0
30.3
50.00
380.0
6.67
1.00
L2
220.0
30.3
50.00
380.0
6.67
1.00
L3
220 .0
30.3
50.00
380 .0
6.67
1.00
Mains
▲
The AC mains screen displays the input L-N voltage, L-N current, input frequency, L-L voltage,
apparent power and power factor of three phases (L1, L2, L3).
Liebert® APS™
50
Operation and Display Panel
4.3.2
Battery Screen
From the main screen, press the F3 button once and the battery screen will be displayed, as shown in
Figure 57.
Figure 57 Battery screens
Liebert APS
Batt Voltage (V)
Batt Current (A)
Runtime (Min.)
Batt Capacity (%)
Batt State
Batt String Count
2014 -01-01
10:45:20
157 .0
0.03
407
100
Batt Full Charge
0
Battery
▲
Liebert APS
Batt Temp ( )
Discharge Count
Discharge Time (H)
EBC Count
▲
2014 -01-01
10:45:20
25.0
303
9.4
0
Battery
▲
▲
▲
ESC
First Screen
Second Screen
On the first battery screen, pressing the F5 button will change the function of the F2, F3, and F4
buttons from the primary functions to the secondary functions, as shown above in Table 23.
The battery screen displays Battery voltage, Battery current, Battery time remaining, Battery
capacity, Battery state, Battery string count, Battery temperature, cumulative discharge count
(highest of all installed battery modules), cumulative discharge time (in hours) and External battery
cabinet count.
4.3.3
Output Screen
The main screen is the output screen by default, as shown in Figure 58.
Figure 58 Output screen
Liebert APS
L-N Voltage (V)
L-N Current (A)
Frequency (Hz)
Power Factor
2013-03-22
3:22:00
220.0
90.9
50.00
0.90
Output
The output screen displays L-N or L-L voltage, L-N or L-L current, Frequency and Power factor.
51
Liebert® APS™
Operation and Display Panel
4.3.4
Load Screen
From the main screen, press the F4 button once and the load screen will be displayed, as shown in
Figure 59.
Figure 59 Load screen
Liebert APS
kVA
kW
Load Level (%)
Crest factor
2014-01-01
10:45:20
20.00
18.00
100.0
3.00
Load
▲
▲
The load screen displays output kVA (Sout/apparent power), output kW (Pout/active power), load
level and crest factor.
4.3.5
UPS Information Screen
From the main screen, press the F4 button twice until the UPS info screen is displayed as shown in
Figure 60)
Figure 60 UPS info screen
The UPS information screen displays UPS ID (name set by user), serial number and software version
of LCD module, system monitor module, system control module, charger module, power module and
battery module (if the modules are installed and are online).
Liebert® APS™
52
Operation and Display Panel
4.3.6
Redundancy Screen
From the main screen, press the F4 button three times until the redundancy screen is displayed, as
shown in Figure 61.
Figure 61 Redundancy screen
Liebert APS
PM Installed
PM
2014-01-01
10:45:20
5
Redundant
Redundant State
▲
▲
The redundant screen displays the number of installed power modules in the frame, and whether the
system contains a redundant module or not.
53
Liebert® APS™
Operation and Display Panel
4.3.7
Settings Screen
From the main screen, press the F4 button four times until the settings screen is displayed. The
settings screen is displayed in a total of nine screens as you scroll down, as shown in Figure 62.
Figure 62 Settings screens
2014-01-01
10:45:20
Liebert APS
Set Redundancy Mode
Remote Comms Shutdown
Bypass Setting
Output Frequency
Output Voltage
Inverter Sync Range
Settings
2014-01-01
10:45:20
Liebert APS
Remote Shutdown Delay
Bypass Upper Limit
Bypass Lower Limit
Guaranteed Shutdown
Bypass Alarm Mode
Set RS232 Protocol
Disabled
Enabled
Enabled
50Hz
230
± 5.0Hz
2second
+10%
-15%
Disabled
Enabled
INTERFACE2
Settings
▲
▲
▲
▲
ESC
First Screen
Second Screen
2014-01-01
10:45:20
Liebert APS
Auto-Restart Mode
Auto-Restart Capacity
Auto-Restart Delay
Display Contrast
Date & Time
Command Password
2014-01-01
10:45:20
Liebert APS
Enabled
20%
12second
Max Load Alarm
Max Load Threshold
Redundant Alarm Mode
Communication Address
Air Filter Reminder
Air Filter Type
2014 -01-01 10 :45:20
*******
Settings
Disabled
0.0kVA
Disabled
1
Disabled
Standard
Settings
▲
▲
▲
▲
ESC
Third Screen
Fourth Screen
2014-01-01
10:45:20
Liebert APS
Disabled
IT System Compatibility
UPS ID
Company Name
Contact Number
Load Factory Default
No
Settings
▲
▲
Fifth Screen
On the first settings screen, pressing the F5 button will prompt a password window to pop up. After
you enter the correct password, the function of the F2, F3, and F4 buttons will switch from the
primary functions to the secondary functions, as shown in Table 23.
4.4
Entering a Password
1. On the password prompt window, press the F5 button, the first digit will become editable, press
the F3 button to enter the correct number.
2. Press the F4 button, the second digit will become editable, press the F3 button to enter the correct
number.
3. Enter the rest of the password digits using the same method in Step 2, and press the F5 button
when complete.
Liebert® APS™
54
Operation and Display Panel
4.5
Setting or Changing a Parameter Setting
1. Press the F4 button to navigate to the parameter to be set, and press the F5 button to enter the
edit mode.
2. Press the F3 or F4 button to select the setting item or change the setting value, then press the F5
button to confirm the setting. Press the F2 button to exit the edit setting mode.
55
Liebert® APS™
Operation and Display Panel
4.5.1
Battery Setting Screen
From the main screen, press the F4 button five times until the battery settings screen is displayed, as
shown in Figure 63.
Figure 63 Battery settings screen
Liebert APS
Low Battery Warning
Auto Batt Test Interval
Auto Batt Test Start Day
Auto Batt Test Start Time
External Battery AH
Load Factory Defaults
2014-01-01
10:45:20
2Min
Disabled
Sunday
06:00
0AH
NO
Battery Set
On the first settings screen, pressing the F5 button will prompt a password window to pop up. After
you enter the correct password, the function of the F2, F3, and F4 buttons will switch from the
primary functions to the secondary functions as shown above in Table 23. Refer to the notes listed
above in section 4.3.7 for entering the password and making changes to the battery setting
parameters.
4.5.2
Language Selection Screen
From the main screen, press the F4 button six times until the language screen is displayed, as shown
in Figure 64.
Figure 64 Language selection screen
The language selection screen displays a choice from seven languages: Chinese, English, German,
Russian, French, Italian and Spanish.
NOTE
The languages are displayed in their alphabet.
To set the language:
1. Press the F5 button, the language option is highlighted.
2. Press the F3 or F4 button to navigate to the desired language.
3. Press the F5 button to confirm the selection. Once the screen language changes, press the F2
button to exit the language setting mode.
Liebert® APS™
56
Operation and Display Panel
4.5.3
Alarms Screen
From the main screen, press the F4 button seven times until the alarms screen is displayed, as shown
in Figure 65.
Figure 65 Alarms screen
The alarms screen displays any current alarms of the UPS, including the alarm name, alarm ID code
and alarm date/time stamp.
4.5.4
Records Screen
From the main screen, press the F4 button eight times until the records screen is displayed, as shown
in Figure 66.
Figure 66 Records screen
The records screen displays all historical alarms of the UPS, including the alarm name, alarm ID
code, alarm date/time stamp and record number/total record count.
57
Liebert® APS™
Operation and Display Panel
4.5.5
Module Replacement Screen
From the main screen, press the F4 button nine times until the module replacement screen is
displayed, as shown in Figure 67.
Figure 67 Module replacement screen
Liebert APS
2014-01-01
10:45:20
LCD Board
Bypass Monitor Board
Bypass Control Board
Power Module
Battery Module
Charger Module
Liebert APS
1. Remove larger plastic bezel
2. Lift up on the LCD module
3. Swap the LCD module
4.Install the new LCD module
5. Replace larger plastic bezel
▲
Module Replacement
Module Replacement
▲
2014-01-01
10:45:20
▲
▲
Module Replacement Screen
▲
LCD Board Replacement Procedures
The module replacement screen displays the procedures for replacing all user replaceable module
assemblies in the UPS frame.
To view the procedure, press the F5 button to enter the module replacement. One module option is
highlighted. Press the F3 or F4 button to navigate to the specific module procedures, and then press
the F5 button to view the procedures. Once completed, press the F2 button to exit.
4.5.6
Prompt Window
During system operation, occasionally the UPS system needs to alert or remind the user of alarm
notifications or require the user to confirm a command or perform other operations. When this occurs,
a prompt window will pop up, as shown in Figure 68. Refer to Table 23 below for possible prompts
and the descriptions/actions to be taken.
Figure 68 Example of prompt window
Liebert® APS™
58
Operation and Display Panel
Table 24
Information and actions required for the prompt window
Prompt Window
Explanation
Turn On/Off:
Turn On UPS
Cancel
When you press the ON/OFF-button while UPS is Off.
Turn On/Off:
Turn On INV
Turn Off UPS
When you press the ON/OFF-button while UPS is operating on bypass
mode.
Turn On/Off:
Transfer to Bypass
Cancel
When you press the ON/OFF-button while UPS is operating on inverter
mode and bypass is qualified.
Turn On/Off:
Turn Off UPS
Cancel
When you press the ON/OFF-button while UPS is operating on inverter
mode and bypass is not qualified.
Enter password
*******
After the control password is changed, you are required to enter the
password when you want to enter “Settings,” “Battery set” and “Service”
screens.
Output must be Off
While the UPS output is supplying power, this prompt appears when you
want to set some key system parameters. You need to close the output
before setting key parameters.
On manual bypass
can't turn Off the load
This prompt appears when UPS operates on manual bypass and the
ON/OFF button is pressed.
Please verify output settings before
starting the UPS
Escape: Ignore this message
Enter: Go to Settings Screen
After the UPS is powered on, When you press the ON/OFF button for the
first time, this prompt appears to remind you of viewing relevant setting.
Short Circuit Recovery
After the UPS output short circuits, wait 30 seconds before turning On
the UPS again.
System is not ready
When the power modules in the frame is initializing or there are no power
modules, this prompt appears when you press the ON/OFF button.
AC input not qualified,
cannot start UPS
When the input voltage cannot meet the startup condition of the inverter,
this prompt appears when you press the ON/OFF button.
Please check air filter
When you set “Enabled” for “Air filter reminder,” this prompt appears after
the reminder time is up.
Removal of module will result
in loss of output power
When only one of the system monitor module OR system control module
is installed and active, when the locking level is moved to the unlock
position, this prompt appears to remind user of loss of output power will
occur if the module is removed from the system.
New Alarms Present
Escape: Ignore this message
Enter: Go to Alarms Screen
Warning! Frame Fan Fault
Reduce load or replace fan
to avoid damage to bypass
Bypass source not qualified
Can not switch to bypass
This prompt appears when a new alarm occurs.
This prompt appears when frame fan is in fault and load is heavy, user
should reduce load or replace fan
This prompt appears when bypass source is not qualified and inverter
can’t power on the load for transformer based frame
59
Liebert® APS™
Troubleshooting
5.0
TROUBLESHOOTING
This chapter provides the basic troubleshooting guide and required actions for maintaining the
Liebert APS system.
5.1
Active Alarms
In the event of an alarm, the User Interface LCD will display the latest alarm message. A list of
possible alarm messages are displayed in Table 25. If an alarm occurs and you are uncertain of the
corrective action to take, contact your local Liebert Services representative.
Table 25
Alarm message list
Alarm Message
Possible Cause
Corrective Action
Power Module Warning
One or more power modules is not
operating correctly.
View the corresponding module serial
number in the fault logs or event logs and
contact your local Liebert Services
representative.
Power Module Fail
One or more power modules has a
fault.
View the corresponding module serial
number in the fault logs or event logs and
either replace the module or contact your
local Liebert Services representative.
Power Module
Over Temp Warning
One or more power modules is
operating at an internal high
temperature.
Check the air filters located behind the
bezels and clean if necessary, or check
to see if the ambient temperature is too
high. If these conditions do not exist,
contact your local Liebert Services
personnel.
Power Module
Over Temp Shutdown
One or more power modules has
stopped operating due to an internal
over temperature.
Check the air filters located behind the
bezels and clean if necessary, or check
to see if the ambient temperature is too
high. If these conditions do not exist,
contact your local Liebert Services
representative.
Power Module Fan Failure
One or more of the power module
fans has failed.
Check to see if the fan is blocked. If not,
contact your local Liebert Services
representative.
Insufficient Capacity To Start
Inverter
The load value exceeds the maximum
load capacity of all operating
modules.
Ensure all power modules are inserted
and the locking lever is fully inserted. If all
modules are active, add power modules
to increase capacity or contact your local
Liebert Services representative.
PM Locking Lever In
Remove Position
The power module locking lever is not
in the locked position.
Check the locking lever to ensure it is
fully inserted. If so, contact your local
Liebert Services representative.
A-phase voltage is too high or too low.
Check the upstream feeder breaker or
the UPS input breaker and reset if
necessary, or contact your local Liebert
Services representative.
Input Phase B Not Qualified
B-phase voltage is too high or too low.
Check the upstream feeder breaker or
the UPS input breaker and reset if
necessary, or contact your local Liebert
Services representative.
Input Phase C Not Qualified
C-phase voltage is too high or too
low.
Check the upstream feeder breaker or
the UPS input breaker and reset if
necessary or contact your local Liebert
Services representative.
Two phases are reversely connected.
Have a qualified electrician check the
phase rotation at the distribution panel
and/or at the UPS input terminal block. If
this is not the problem, contact your local
Liebert Services representative.
Input Phase A Not Qualified
L1L2 Phase Reversed
Liebert® APS™
60
Troubleshooting
Table 25
Alarm message list (continued)
Alarm Message
Possible Cause
Corrective Action
The battery is reversely connected.
Have a qualified electrician check the
wiring rotation at the external battery
cabinet. If this is not the problem, contact
your local Liebert Services
representative.
No Battery Modules Are
Ready
The battery module is not ready, and
the yellow fault LED flashes.
Ensure that the battery module is fully
inserted and locking levers are in the
locked position. If this is not the problem,
contact your local Liebert Services
representative.
All PM’s Are Not Ready
The power module is not ready, and
the yellow fault LED flashes.
Ensure that the power module is fully
inserted in the upper frame bays and
locking levers are in the locked position.
If this is not the problem, contact your
local Liebert Services representative.
Power Module Redundancy
Alarm
The UPS has no redundant power
module
Add power modules or replace the faulty
power module to obtain redundancy, or
contact your local Liebert Services
representative.
Output Exceeds Max Load
Setting
The maximum load alarm is effective,
the actual load is larger than the
setting
Either decrease load on the UPS or
readjust the user programmable alarm
set point from the LCD. It might also
require another power module to
increase capacity. If this is not the
problem, contact your local Liebert
Services representative.
Turn Rocker Switch Off
Before Removing
The bypass power is unqualified or
the system output is disconnected.
There is only one system monitor
module or one system control module
in the system, and the control lever is
removed. The alarm reminds you to
open the startup switch before pulling
out the control module.
Open the startup switch.
Time to Check the Fan Filters
for Excessive Dirt
When the air filter reminder is
‘Enabled,’ this message appears to
remind users to check the air filters.
Check the air filters and clean them if
necessary, or contact your local Liebert
Services representative.
No Matching Module
Only one battery module is inserted
into one layer of bays in the system.
Ensure that there are a pair of battery
modules in the same layer of the frame,
or contact your local Liebert Services
representative.
Load Exceeds Battery
Module Capacity
The system has determined the load
exceeds the capacity of the battery.
Check to ensure that all battery modules
are fully inserted and the locking lever is
in the locked position. It is possible that
more battery modules are required to
increase battery run time. If this is not the
problem, contact your local Liebert
Services representative.
Battery Cabinet Not
Connected
The power cable of the external
battery cabinet is not connected or
fully inserted.
Connect the cable or contact your local
Liebert Services representative.
BM Lock Lever in Remove
Position
The locking lever is not in the locked
position.
Check the locking lever to ensure it is
fully inserted. If so, contact your local
Liebert Services representative.
The internal battery module
temperature is at an elevated level.
Check the air filters located behind the
bezels and clean if necessary, or check
to see if the ambient temperature is too
high. If this is not the problem, contact
your local Liebert Services
representative.
Battery Reversed
BM Over Temperature
Warning
61
Liebert® APS™
Troubleshooting
Table 25
Alarm message list (continued)
Possible Cause
Corrective Action
Low Battery Warning
The battery capacity has reached the
user programmable set point.
Check upstream feeder breaker or the
UPS input breaker and reset if
necessary.If this is not the problem,
begin the orderly shutdown of all
connected equipment as UPS shutdown
is imminent.
Battery Module Warning
One or more battery modules is
abnormal.
View the corresponding module serial
number in the fault logs or event logs and
contact your local Liebert Services
representative.
Battery Module Fail
One or more battery modules has a
fault.
View the corresponding module serial
number in the fault logs or event logs and
either replace the module or contact your
local Liebert Services representative.
Battery Test Warning Weak
Battery
One or more battery modules has
detected batteries that are no longer
in specification due to age or
operating conditions.
Replace the battery string or contact your
local Liebert Services representative.
BM Temp Unbalance
The temperature difference between
all the battery modules exceeds 10°C.
Check the air filters located behind the
bezels and clean if necessary, or check
to see if the ambient temperature is too
high. If this is not the problem, contact
your local Liebert representative.
Frame Fan Failure
The fan located behind the display
panel has failed.
Contact your local Liebert Services
representative for fan replacement.
Transformer Fan Failure
There is a transformer on the UPS
frame and at least one transformer
fan has failed.
Contact your local Liebert Services
representative for fan replacement.
Transformer Temperature
Warning
A high temperature condition has
occurred in the output transformer
area.
Check the air filters located behind the
bezels and clean if necessary, or check
to see if the ambient temperature is too
high. If this is not the problem, contact
your local Liebert Services
representative.
Bypass Source Not Qualified
The UPS bypass functionality is not
available because the input source is
out of tolerance to the bypass voltage
and/or frequency window.
No action necessary unless the AC input
has been verified within bypass settings.
If this is not the problem, contact your
local Liebert Services representative.
Output Is Off
Abnormal Output Volt
The cable connection is wrong.
Check the power distribution.
System Control Module Lock
Lever in Remove Position
The locking lever is not in the locked
position.
Check the locking lever to ensure it is
fully inserted. If so, contact your local
Liebert Services representative.
System Monitor Module Lock
Lever in Remove Position
The locking lever is not in the locked
position.
Check the locking lever to ensure it is
fully inserted. If so, contact your local
Liebert Services representative.
Charger Module Warning
The charger module is not operating
correctly.
View the corresponding module serial
number in the fault logs or event logs,
and contact your local Liebert Services
representative.
The charger module has a fault.
View the corresponding module serial
number in the fault logs or event logs,
and either replace the module or contact
your local Liebert Services
representative.
Check the power distribution.
Check upstream feeder breaker or the
UPS input breaker and reset if
necessary, or contact your local Liebert
Services representative
Alarm Message
Charger Module Fail
CM Power source Is Not
Qualified
Liebert® APS™
62
Troubleshooting
Table 25
Alarm message list (continued)
Possible Cause
Alarm Message
5.2
Corrective Action
Charger Module LOCK Lever
in Remove Position
The locking lever is not in the locked
position.
Check the locking lever to ensure it is
fully inserted. If so, contact your local
Liebert Services representative.
Charger Module Fan Failure
One or more of the charger module
fans has failed.
Check to see if the fan is blocked. If not,
contact your local Liebert Services
representative.
Charger Module
Temperature Warning
One or more charger modules is
operating at an internal high
temperature.
Check the air filters located behind the
bezels and clean if necessary, or check
to see if the ambient temperature is too
high. If this is not the problem, contact
your local Liebert Services
representative.
Module Troubleshooting
The power, battery, charger, system control and system monitor module have two LEDs each to
indicate the module operating state. Figure 69 shows the location of these LEDs; the meaning of the
LED indicators is detailed in Table 26.
Figure 69 Module LED location
Green Status LED
Green Status LED
Yellow Fault
LED
Yellow Fault LED
Battery
Module
Power Module
Green Status LED
Yellow Fault LED
Table 26
System Control Module
and System Monitor Module
Descriptions of module LEDs
Green Status LED Yellow Fault LED
Descriptions of Module State
Off
Off
The module is not inserted into the frame, lock lever is in unlocked
position or the system is off
Off
On
The module is initializing (maximum 30 seconds 1)
Flashing
Off
The module is operating normally
Flashing
Flashing
Flashing
On
Off
Flashing
On
Off
On
On
On
Flashing
The module is in startup mode or the module has an alarm 2
The module is faulty and off-line, and the control module is operating
The module is not operating correctly, re-insert the module. If this
persists, contact technical support personnel.
1. If this condition persists for more than 30 seconds, verify that the lock lever is in the locked position; if it is not, the module is
faulty.
2. If both green and yellow LEDs are flashing for more than 30 seconds, reinsert module.
63
Liebert® APS™
Troubleshooting
5.3
Module Replacement
Follow the instructions below when replacing or adding a system control, system monitor, power,
battery, or charger module. Contact your local Liebert representative if you need to purchase
additional modules to expand your system or contact authorized your Liebert Services representative
for replacement modules.
5.3.1
Removing Modules
1. Remove bezel cover to locate the faulty module. The yellow fault LED will be illuminated on the
faulty module.
NOTE
When removing bezels from a transformer-based UPS, note which have filters and replace
them accordingly. Bezels from the modules will have air filters. There will be no filters on the
bottom three transformer bezels. The transformer has a separate air filter.
For module removal, after unlocking the lever, wait a few seconds to remove the module.
If your system does not contain a redundant module, you may need to manually place the UPS
into manual bypass before removing modules to avoid accidental loss of output power for the
connected equipment.
2. The method for removing a module varies depending on the module type. The two methods are as
follows:
• When removing a power, battery or charger module, use a Phillips screwdriver to remove
the fastener (if installed). Then pull out the lock lever slightly and lift up to unlock the
module.
• When removing a system control or system monitor module, use a Phillips screwdriver
to remove the two screws from the securing holes on each end. Then pull out the lock lever
slightly and slide it to the left to unlock the module.
Figure 70 Lever and fastener
Locking Lever
Securing Hole
Fastener
Locking Lever
System Control Module or System Monitor Module
Power Module
3. To pull out a power, charger or battery module:
a. When removing a power module, charger module or battery module: slide it 2/3 of the way out.
It will be stopped by the safety catch.
b. Lift the module up slightly while continuing to pull it out as shown in Figure 71.
c. Support the module and slide it completely out of the unit.
d. When removing a system control or a system monitor module, there is no safety catch because
the modules are lightweight.
Liebert® APS™
64
Troubleshooting
Figure 71 Pull out a battery module, a power module or a charge module
Step 3
Step 3
Step 3
! WARNING
Risk of heavy unit falling over. Can cause equipment damage, injury or death.
Read all of the instructions before attempting to move the unit, lift it, remove packaging or
prepare the unit for installation.
The UPS presents a tipping hazard. Do not remove more than one module at a time. Failure
to do so may cause unit to tip over and cause serious injury.
65
Liebert® APS™
Troubleshooting
5.3.2
Replacing the User Interface Module
1.
2.
3.
4.
5.
Remove the display bezel on top of the frame.
Lift up the user interface module, and put it on top of the UPS frame.
Disconnect the network cable from the user interface module.
Connect the network cable to the new user interface module.
Insert the new user interface module into the clips and replace the display bezel.
Figure 72 Replacing the user interface module
Display Bezel
User Interface
Module
Liebert® APS™
66
Maintenance
6.0
MAINTENANCE
This chapter describes the routine maintenance for the Liebert APS UPS, including proper care,
scheduled maintenance and procedures for cleaning fan filters.
6.1
Proper Care
Proper maintenance of the UPS is imperative to optimal performance and life of the unit. Emerson
recommends that a certified technician perform preventive and corrective maintenance. Emerson
Network Power Liebert Services is dedicated to ensuring the highest level of performance and
unmatched support for your UPS. Contact your local Liebert representative for service.
6.2
Scheduled Maintenance
Emerson recommends performing the following maintenance at least monthly:
• Clean unit.
• Clean or replace filters.
• Verify proper airflow.
Emerson recommends performing the following maintenance annually:
• Verify that all power modules are operating properly.
• Verify that all battery modules are operating properly.
• Verify redundancy (if applicable).
6.3
Cleaning Fan Filters
The intake fans contain filters that will need to be replaced or cleaned periodically, depending on the
surrounding environment. Check filters; replace if they are very dirty or damaged.
To clean filters, either use a vacuum to remove the dirt and dust or rinse out the filters under running
water (with the dirt side down) to remove dirt and dust. Blot the filters dry with a towel and allow
air-drying before reinstalling it.
6.3.1
Top Filter
1.
2.
3.
4.
Remove the display bezel.
Remove the user interface module, and lay it on top of the UPS frame.
Remove the two screws on the LCD mounting plate
Remove the screw in the middle of the filter assembly, remove the filter, as shown in Figure 73,
and clean the filters as described above.
5. Replace the filter, mounting plate, user interface module and display bezel.
Figure 73 Replace/clean the top filter
Filter
Screw,
1 Place
67
Liebert® APS™
Maintenance
6.3.2
Bezel Filter
1. Remove the bezel from the frame.
2. Remove the filter assembly from the bezel, as shown in Figure 74, and clean the filters as
described above.
3. Restore the filter and small plastic bezel of the frame.
Figure 74 Replace/clean the bezel filter
6.3.3
Bottom Fan Filter—Transformer-Based Frames Only
1. Remove the three lower bezels at the bottom of the frame.
2. Remove the screws and take out the filter, as shown in Figure 75, and clean the filters as
described above.
3. Replace the filter and bezels.
Figure 75 Replace/clean the bottom fan filter
Bottom Fan Filters
Liebert® APS™
68
Specifications
7.0
SPECIFICATIONS
Table 27
Liebert APS specifications
10 Bay
Unit Size, Type
Frame Rating, kVA/kW
General & Environmental
Conducted and Radiated
EMC Levels
Compliant Safety Standards
16 Bay
12 Bay
No Transformer
15/13.5
16 Bay
Transformer-based
20/18
15/13.5
20/18
10 Bay
16 Bay
No Transformer
Dual Inverter
15/13.5
20/18
IEC/EN/AS 62040-2 Cat 2, CISPR22 Class A, FCC Part 15 Class A
IEC/EN/AS 62040-1:2008,
UL 1778 4th Ed and CSA 22.2 No. 107.3
UL 1778 4th Ed and
CSA 22.2 No. 107.3
Compliant Immunity
IEC/EN/AS 61000-4-2, 3, 4, 5, 6
Standards
Transportation
Individual packaged modules meet ISTA-1A / 1B; the complete system meets ISTA-1E
UPS Classification According
VFI-SS-111
to IEC EN 62040-3
Environmental
WEEE and ROHS2 (6 by 6), REACH Compliant
Protection Degree
IP 20
IEC60529
Color
RAL 7021
Dimensions, W x D x H, mm (in)
440 x 800 x 695 440x850x970 440x800x1060 440x850x1240 440x800x695 440x850x970
(17x32x27)
(17x34x38)
(17x32x42)
(17x34x49)
(17x32x27)
(17x34x38)
Weight, kg (lb)
Unit Weight
127 (280)
145.1 (320)
231.3 (510)
244.9 (540)
127 (280)
145.1 (320)
(empty frame)
Shipping Weight
145.1 (320)
163.3 (360)
249.5 (550)
263.1 (580)
145.1 (320)
163.3 (360)
(empty frame)
Unit Weight
256.3 (565)
317.5 (700)
360.6 (795)
417.3 (920)
256.3 (565)
317.5 (700)
(frame rating populated)
Shipping Weight
274.4 (605)
335.7 (740)
378.7 (835)
435.4 (960)
274.4 (605)
335.7 (740)
(frame rating populated)
Environmental
Operating Temperature,
0 - 40 (32 - 104)
°C (°F)
Relative Humidity, %
0 - 95%, non-condensing
Altitude, m (ft)
3000 (10000) @ 25°C (77°F)
Efficiency (AC-AC), %
91.8-92.0
91.6-92.0
88.5-89.9
88.6-89.7
90.4-91.0
90.0-91.0
Nominal Heat Dissipation
4208
5747
5528
7965
4904
6768
BTU/Hr (maximum)
Acoustic Noise Level, dBA
< 55dB (< 50% load), < 65dB (51-100% load) @ 1 meter
Input Data
200/208/220/230/240; Single-Phase
200/100, 220/110, 230/115,
Nominal Input Voltage,
240/120, 254/127, 208/120,
VAC
173/100, 190/110, 200/115,
380/400/415; Three-Phase
—
—
220/127; Two-Phase
Input Voltage Range,
The input voltage range based on the output loading, refer to Table 28
VAC
Single-Phase Input, > 0.99;
Single-Phase Input, > 0.99
Power Factor, Cos
Three-phase Input, > 0.95
Input Frequency, Nominal,
50/60
Hz
Input Current
< 5%
Distortion, THDi
Input Frequency Range, Hz
40 to 70 auto-sensing
69
Liebert® APS™
Specifications
Table 27
Liebert APS specifications (continued)
10 Bay
Unit Size, Type
Frame Rating, kVA/kW
Battery Module
Lead-Acid Batteries
Per String, Pieces
Battery Cells Per String,
Pieces
Battery Capacity, W
Backup Time, Minutes,
Full Load
Maximum Charge Current
(Full, Load)
Nominal Voltage, VDC
Recharge Time, Hr
Output Data
Output Voltage, VAC
16 Bay
12 Bay
No Transformer
15/13.5
Transformer-based
20/18
15/13.5
Dual-Inverter
Configured to 100,
110 or 115 VAC per Phase
Single-Inverter
Transformer-Based and
Transformer-Free
Liebert® APS™
15/13.5
20/18
5 (for non-redundant system which has equal number of battery strings and power modules)
Power module internal charger: 1.8A
Charger module: 10A
144
< 5 to 90% capacity (PM internal charger with 1:1 ratio of PM to Battery Strings)
100/100/173/200
110/110/190/220
115/115/199/230
120/120/208/240
Single-Phase
±3
200/208/220/230/240
Single-Phase
200/100, 220/110, 230/115,
240/120, 254/127, 208/120,
173/100, 190/110, 200/115,
220/127; Two-Phase
±7
≤ 60
≤ 3, linear load
≤ 7, non-linear load
50/60
< 104% continuous
105% - 130% for 1 min
131% - 150% for 10 sec
151% - 200% for 1 sec
> 201% for 250 msec
≤ 5, non-linear load
Rated input voltage range (Unit: VAC)
Dual-Inverter
Configured to 120
or 127 VAC per Phase
No Transformer
Dual Inverter
36W @ 15min-rate to 1.67V per cell @25°C (77°F)
Output Overload
Capability, %
System Configuration
16 Bay
72
Output Frequency, Hz
Table 28
20/18
10 Bay
12
Voltage Regulation, %
Voltage Stability
(100% Step Load), %
Voltage Recovery Time, ms
Voltage Distortion, %
16 Bay
% UPS Load
Low Limit Value
>100%
90% ~ 100%
70% ~ 90%
30% ~ 70%
<30%
>100%
90% ~ 100%
70%~90%
40%~70%
<40%
> 100%
90 ~ 100%
70 ~ 90%
50 ~ 70%
< 50%
98 ±3.1
89 ±3.1 ~ 98 ±3.1
74 ±3.1 ~ 89 ±3.1
60.5 ±3.1 ~ 74 ±3.1
60.5 ±3.1
84 ±3.1
80 ±3.1 ~ 84 ±3.1
72 ±3.1 ~ 80 ±3.1
60 ±3.1 ~ 72 ±3.1
60 ±3.1
170 ±5
160 ±5 ~ 170 ±5
140 ±5 ~ 160 ±5
120 ±5 ~ 140 ±5
120 ±5
70
High Limit Value
139.5 ±3.1
280 ±5
≤ 5, non-linear load
Specifications
Table 29
Liebert APS external battery cabinet specifications
Parameters
AS7EBCNCC1BX000
General and Environmental
Conducted and Radiated EMC Levels
Safety Standards
Immunity Standards
Transportation
IEC/EN/AS 62040-2—Class A, FCC Part 15 (Class A)
IEC/EN/AS 62040-1:2008, UL 1778 4th Ed and CSA 22.2 No. 107.3
IEC/EN/AS 61000-4-2, 3, 4, 5, 6
ISTA-1E
17x28x38
(440x712x970)
Dimensions, WxDxH
Unit Weight, lb (kg)
147.7 (67)
Shipping Weight, lb (kg)
209.4 (95)
Environmental
Operating Temperature °F (°C)
Storage Temperature, °F (°C)
32 to 104 (0 to 40)
Without battery: -4 to 140 (-20 to 60)
With battery: 5 to 104 (-15 to 40)
Relative Humidity, %
0 - 95%, non-condensing
Altitude, ft. (m)
10000 (3000)
Battery Module *
Lead-Acid Batteries (Per String)
Backup Time (Full Load), Minutes
*
12
See Estimated Battery Run Times, 7.1 through 7.5
Up to four external battery cabinets can be connected to each UPS frame and each external battery cabinet can be configured
with up to seven strings of batteries.
71
Liebert® APS™
Liebert® APS™
27
28
29
30
31
32
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
90%
80%
70%
60%
50%
40%
72
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
113 135 147 156 164 187 202 215 226 308 317 324 331 337 342 347 423 427 431 434 437 440 443 445 448 450 452
10
16
21
91
64
48
41
33
27
23
26
33
99
75
53
48
43
38
39
44
48
97
77
66
52
52
63
70
94
78
76
81
97
93
99
105 110 120 126 131 135 139 143 146 149 152 155 157 160 162
103 109 120 126 131 136 140 144 148 151 154 157 160 162 165 167 183
102 108 120 126 132 138 142 146 150 154 157 160 163 165 180 187 193 199 204
90
100 107 120 127 134 140 145 149 153 157 160 164 166 184 191 198 204 210 215 220 225
81
72
106 113 128 135 142 147 152 157 161 164 167 188 196 203 210 216 222 227 304 309 313 317
91
74
64
103 113 129 137 145 151 156 161 165 183 193 202 210 217 224 302 308 313 318 322 327 331 334 338
81
69
52
48
111 129 140 148 155 161 166 188 199 209 218 226 306 312 318 324 329 333 337 341 345 420 424 427 429
92
71
53
48
44
109 130 143 153 161 167 194 208 220 302 311 318 325 332 337 342 347 423 427 430 434 437 440 442 445 447 449
79
61
48
42
36
30
105 133 149 161 186 207 223 309 320 330 338 345 423 428 433 438 441 445 448 451 454 456 459 461 463 464 466 480 480
67
47
38
28
25
21
18
98
44
27
20
15
11
9
8
6
5
98
69
50
43
37
30
26
22
94
71
52
46
41
35
30
92
71
53
48
44
39
83
72
60
50
46
97
77
66
52
48
94
77
67
53
91
76
68
97
80
72
95
80
99
83
97
101 105 108 111 120 124
103 107 110 120 124 127 131 134
93
102 106 110 120 124 128 132 136 139 142 145
90
76
100 105 109 120 125 129 134 138 141 145 148 151 153 156
81
72
63
103 109 113 125 131 135 140 144 147 151 154 157 159 162 164 166
82
72
61
51
100 107 113 126 132 137 142 147 151 155 158 161 164 166 183 190 196 202 208
78
65
51
47
43
104 111 126 133 140 145 151 155 159 163 166 184 192 199 206 213 219 224 301 306 310
79
64
50
45
40
35
109 125 135 143 150 156 161 165 184 194 204 212 220 227 305 311 316 321 325 330 334 337 341
79
61
48
42
36
30
26
-
-
-
-
-
-
-
-
-
80
53
45
37
30
26
22
19
132 152 165 201 222 311 324 335 344 424 430 436 441 445 449 453 456 459 461 464 466 480 480 480 480 480 480 480
67
47
38
28
25
21
18
16
-
81
50
40
28
23
19
16
14
12
105 125 139 149 157 164 186 200 212 223 304 313 320 326 332 337 342 347 423 426 430 433 436 439 441 444
63
41
28
22
18
14
12
10
8
144 166 213 312 331 345 428 436 444 450 455 459 463 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
73
46
34
26
20
17
14
12
Tables for UPS Where Model Number Digits 1-3 are AS1 or ASA
-
96
112 136 150 160 181 200 216 301 312 321 329 336 343 420 425 430 434 438 441 444 447 450 452 454 456 458 460 462
110 138 154 165 197 216 304 316 327 336 344 422 428 433 438 442 446 449 452 455 457 460 462 464 466 467 480 480 480
90
71
108 142 160 192 217 309 324 336 345 426 432 438 444 448 452 456 459 462 464 466 480 480 480 480 480 480 480 480 480 480
78
60
48
7.1.1
-
-
-
-
99
44
27
20
15
11
9
8
6
5
66
47
38
28
102 120 132 142 150 157 163 180 193 204 214 223 303 310 316 322 327 332 336 341 344 420 423 426 429 432
Estimated Battery Run Times
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
-
-
100%
99 166 312 345 437 450 459 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
26
10%
25
44 104 148 185 222 319 337 422 432 441 448 453 458 462 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
24
27
23
20%
22
30%
21
19
20
40%
19
100 120 134 144 153 160 166 191 204 215 225 305 313 320 326 332 337 341 346 421 425 428 432 434 437 440 442
81
18
15
77
66
17
11
53
48
16
# Battery Strings
15
105 120 130 139 146 152 157 162 166 186 196 204 212 220 226 304 310 315 320 324 328 332 336 339
14
104 120 131 140 148 154 160 165 184 195 204 213 221 300 307 313 318 323 328 332 336 340 343 346 422
93
13
50%
42
36
90
76
12
60%
25
21
72
63
11
9
52
48
10
8
44
39
9
70%
30
26
8
80%
18
16
7
6
6
5
5
90%
4
100%
3
1
Load
Level
2
10-bay, single-phase, no transformer unit Type N (& UPS model number digit 6 = N)
7.1
15 kVA /
13.5 kW
10 kVA /
9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 30
Specifications
73
1
5
6
8
9
11
15
19
27
44
99
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Load
Level
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
99
44
27
20
15
11
9
8
6
5
166
104
66
47
38
28
25
21
18
16
2
98
44
27
20
15
11
9
8
6
5
144
73
46
34
26
20
17
14
12
10
312
148
108
78
60
48
42
36
30
26
3
132
63
41
28
22
18
14
12
10
8
166
105
67
47
38
28
25
21
18
16
345
185
142
110
90
71
53
48
44
39
4
152
81
50
40
28
23
19
16
14
12
213
133
91
64
48
41
33
27
23
21
437
222
160
138
112
96
77
66
52
48
5
165
105
67
47
38
28
25
21
18
16
312
149
109
79
61
48
42
36
30
26
450
319
192
154
136
113
100
81
72
63
6
201
125
80
53
45
37
30
26
22
19
331
161
130
99
75
53
48
43
38
33
459
337
217
165
150
135
120
102
90
76
7
222
139
98
69
50
43
37
30
26
22
345
186
143
111
92
71
53
48
44
39
466
422
309
197
160
147
134
120
104
93
8
311
149
109
79
61
48
42
36
30
26
428
207
153
129
103
81
69
52
48
44
480
432
324
216
181
156
144
132
120
105
9
324
157
125
94
71
52
46
41
35
30
436
223
161
140
113
97
77
66
52
48
480
441
336
304
200
164
153
142
131
120
10
335
164
135
104
79
64
50
45
40
35
444
309
167
148
129
106
91
74
64
52
480
448
345
316
216
187
160
150
140
130
11
344
186
143
111
92
71
53
48
44
39
450
320
194
155
137
113
100
81
72
63
480
453
426
327
301
202
166
157
148
139
12
424
200
150
126
100
78
65
51
47
43
455
330
208
161
145
128
107
94
78
70
480
458
432
336
312
215
191
163
154
146
13
430
212
156
133
107
83
72
60
50
46
459
338
220
166
151
135
120
102
90
76
480
462
438
344
321
226
204
180
160
152
14
436
223
161
140
113
97
77
66
52
48
463
345
302
188
156
142
127
108
97
81
480
466
444
422
329
308
215
193
165
157
15
441
304
165
145
126
103
82
72
61
51
466
423
311
199
161
147
134
120
103
93
480
480
448
428
336
317
225
204
184
162
16
445
313
184
151
132
109
94
77
67
53
480
428
318
209
165
152
140
126
109
99
480
480
452
433
343
324
305
214
195
166
17
449
320
194
155
137
113
100
81
72
63
480
433
325
218
183
157
145
132
120
105
480
480
456
438
420
331
313
223
204
186
18
# Battery Strings
453
326
204
159
142
125
105
91
76
68
480
438
332
226
193
161
149
138
126
110
480
480
459
442
425
337
320
303
213
196
19
456
332
212
163
147
131
109
97
80
72
480
441
337
306
202
164
153
142
131
120
480
480
462
446
430
342
326
310
221
204
20
459
337
220
166
151
135
120
102
90
76
480
445
342
312
210
167
157
146
136
126
480
480
464
449
434
347
332
316
300
212
21
10-bay, single-phase, no transformer unit Type N (& UPS model number digit 6 = N)
461
342
227
184
155
140
125
106
95
80
480
448
347
318
217
188
160
150
140
131
480
480
466
452
438
423
337
322
307
220
22
464
347
305
192
158
144
129
110
99
83
480
451
423
324
224
196
164
154
144
135
480
480
480
455
441
427
341
327
313
226
23
466
423
311
199
161
147
134
120
103
93
480
454
427
329
302
203
166
157
148
139
480
480
480
457
444
431
346
332
318
304
24
480
426
316
206
164
151
138
124
107
97
480
456
430
333
308
210
184
160
151
143
480
480
480
460
447
434
421
336
323
310
25
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
15 kVA /
13.5 kW
10 kVA /
9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 31
480
430
321
213
166
154
141
128
110
101
480
459
434
337
313
216
191
163
154
146
480
480
480
462
450
437
425
341
328
315
26
480
433
325
219
183
157
145
132
120
105
480
461
437
341
318
222
198
165
157
149
480
480
480
464
452
440
428
344
332
320
27
480
436
330
224
190
159
148
136
124
108
480
463
440
345
322
227
204
180
160
152
480
480
480
466
454
443
432
420
336
324
28
480
439
334
301
196
162
151
139
127
111
480
464
442
420
327
304
210
187
162
155
480
480
480
467
456
445
434
423
340
328
29
480
441
337
306
202
164
153
142
131
120
480
466
445
424
331
309
215
193
165
157
480
480
480
480
458
448
437
426
343
332
30
480
444
341
310
208
166
156
145
134
124
480
480
447
427
334
313
220
199
167
160
480
480
480
480
460
450
440
429
346
336
31
-
-
-
-
-
-
-
-
-
-
480
480
449
429
338
317
225
204
183
162
480
480
480
480
462
452
442
432
422
339
32
Specifications
Liebert® APS™
Liebert® APS™
74
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
111 129 140 148 155 161 166 188 199 209 218 226 306 312 318 324 329 333 337 341 345 420 424 427 429
107 131 145 156 165 191 207 221 304 314 323 331 337 343 420 425 429 433 437 440 443 446 449 451 453 455 457 459
133 153 166 203 224 312 326 336 345 425 431 437 442 446 450 453 457 459 462 464 466 480 480 480 480 480 480 480 480
-
-
-
-
-
-
-
-
-
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
81
104 124 138 148 157 163 184 199 211 222 303 311 319 325 331 336 341 346 422 426 429 432 435 438 441 443
126 143 156 165 195 213 227 311 321 330 338 344 422 427 432 436 440 443 446 449 452 454 457 459 461 463 464
91
42
27
19
15
11
9
7
6
5
94
67
50
43
36
28
26
22
92
69
51
46
40
35
30
90
70
52
48
43
39
98
77
64
51
46
42
95
76
65
52
48
93
76
66
53
98
80
71
62
96
79
72
94
79
98
83
97
101 104 108 111 120 123
102 106 110 113 123 127 130 133
93
101 105 109 113 123 127 131 135 138 141 144
83
76
104 108 113 123 128 132 136 140 143 147 149 152 155
90
75
67
102 107 112 124 129 134 138 142 146 150 153 156 158 161 163 165
81
71
60
51
105 111 124 130 136 141 145 149 153 156 160 162 165 180 187 193 199 205
82
71
53
49
46
101 109 123 131 137 143 148 153 157 161 164 167 187 195 202 209 215 220 226 302 307
77
62
49
44
39
35
106 122 132 140 147 153 158 163 167 188 198 207 215 222 300 306 312 317 321 326 330 334 337
77
60
48
41
35
28
26
-
-
-
-
-
-
-
-
-
-
77
52
44
37
28
25
21
19
-
125 146 161 189 212 302 316 327 337 345 424 430 436 440 445 448 452 455 457 460 462 464 466 480 480 480 480 480
64
46
38
28
25
20
18
16
-
-
78
49
38
28
23
19
16
13
12
-
100 120 134 145 154 161 167 192 205 216 226 306 314 321 327 332 337 342 346 422 426 429 432 435 438 440
53
40
27
22
18
14
11
10
8
136 160 199 300 320 336 420 429 437 444 449 454 458 462 465 480 480 480 480 480 480 480 480 480 480 480 480 480 480
98
62
100 110 126 134 142 148 154 159 163 167 188 197 205 213 220 226 304 309 314 319 323 327 331
108 125 136 144 152 158 163 180 192 202 212 220 300 307 313 318 324 328 333 337 341 344 420 423
83
106 113 126 132 138 143 148 152 156 159 163 165 181 189 195 202 207 213 218
-
-
-
90
-
-
10%
100%
67
44
95
72
98
104 112 126 133 140 146 151 155 159 163 166 184 192 200 207 213 219 224 301 306 311
83
104 109 113 125 130 134 138 142 145 149 151 154 157 159
103 108 113 125 130 135 140 144 147 151 154 157 159 162 164 166
99
41
26
76
53
76
95
96
92
101 107 113 126 131 137 141 146 150 153 156 159 162 165 167 185 191 197
83
81
-
60
47
67
79
94
78
75
-
46
37
52
70
80
71
69
20%
32
25
48
53
74
64
62
30%
19
14
41
47
65
52
52
-
33
40
52
48
48
-
25
28
48
43
44
40%
16
20
43
37
39
50%
9
11
35
28
32
-
27
23
26
-
20
18
20
60%
14
11
15
70%
7
6
10
-
5
-
138 161 203 303 323 338 422 431 439 445 451 455 459 463 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
99
13
80%
92
53
12
104 132 148 160 184 205 222 307 319 328 337 344 422 427 432 437 441 444 447 450 453 456 458 460 462 464 466 467 480
80
11
110 130 141 150 158 164 184 197 209 219 300 308 315 322 327 333 338 342 346 422 425 428 431 434 437 439
99
10
103 113 129 137 145 151 156 161 165 183 193 202 210 217 224 302 308 313 318 322 327 330 334 338
9
101 112 129 138 146 153 158 163 167 190 200 209 218 225 304 310 315 320 325 329 334 337 341 344 347
92
8
109 131 143 153 161 167 195 208 220 302 311 319 326 332 337 343 347 423 427 431 434 437 440 442 445 447 449
96
79
82
75
7
90%
39
20%
72
52
91
74
64
70
61
6
-
25
30%
44
35
67
52
47
51
48
5
78 154 216 327 422 438 449 457 464 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
18
40%
46
40
34
43
38
4
10%
14
50%
27
23
20
28
26
3
# Battery Strings
100%
9
11
7
80%
60%
6
90%
70%
15
5
100%
17
2
Load
Level 1
10-bay, single-phase, no transformer unit Type R (& UPS model number digit 6 = R)
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
15 kVA/
13.5 kW
10 kVA /9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 32
Specifications
75
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
99
44
27
19
15
11
9
8
6
5
2
3
99
44
27
20
15
11
9
8
6
5
166
104
66
47
38
28
25
21
18
16
4
144
73
46
34
26
20
17
14
12
10
312
148
108
78
60
48
42
36
30
26
5
166
105
67
47
38
28
25
21
18
16
345
185
142
110
90
71
53
48
44
39
6
213
133
91
64
48
41
33
27
23
21
437
222
160
138
112
96
77
66
52
48
7
312
149
109
79
61
48
42
36
30
26
450
319
192
154
136
113
100
81
72
63
8
331
161
130
99
75
53
48
43
38
33
459
337
217
165
150
135
120
102
90
76
9
345
186
143
111
92
71
53
48
44
39
466
422
309
197
160
147
134
120
104
93
10
428
207
153
129
103
81
69
52
48
44
480
432
324
216
181
156
144
132
120
105
11
436
223
161
140
113
97
77
66
52
48
480
441
336
304
200
164
153
142
131
120
12
444
309
167
148
129
106
91
74
64
52
480
448
345
316
216
187
160
150
140
130
13
450
320
194
155
137
113
100
81
72
63
480
453
426
327
301
202
166
157
148
139
14
455
330
208
161
145
128
107
94
78
70
480
458
432
336
312
215
191
163
154
146
15
459
338
220
166
151
135
120
102
90
76
480
462
438
344
321
226
204
180
160
152
16
463
345
302
188
156
142
127
108
97
81
480
466
444
422
329
308
215
193
165
157
17
466
423
311
199
161
147
134
120
103
93
480
480
448
428
336
317
225
204
184
162
18
480
428
318
209
165
152
140
126
109
99
480
480
452
433
343
324
305
214
195
166
19
480
433
325
218
183
157
145
132
120
105
480
480
456
438
420
331
313
223
204
186
20
480
438
332
226
193
161
149
138
126
110
480
480
459
442
425
337
320
303
213
196
21
480
441
337
306
202
164
153
142
131
120
480
480
462
446
430
342
326
310
221
204
22
480
445
342
312
210
167
157
146
136
126
480
480
464
449
434
347
332
316
300
212
23
480
448
347
318
217
188
160
150
140
131
480
480
466
452
438
423
337
322
307
220
24
480
451
423
324
224
196
164
154
144
135
480
480
480
455
441
427
341
327
313
226
25
480
454
427
329
302
203
166
157
148
139
480
480
480
457
444
431
346
332
318
304
26
480
456
430
333
308
210
184
160
151
143
480
480
480
460
447
434
421
336
323
310
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
10 kVA /
9 kW
5 kVA
/4.5 kW
-
100%
# Battery Strings
10-bay, single-phase, no transformer unit Type B (& UPS model number digit 6 = B)
UPS
Load
Rating Level 1
Table 33
27
480
459
434
337
313
216
191
163
154
146
480
480
480
462
450
437
425
341
328
315
28
480
461
437
341
318
222
198
165
157
149
480
480
480
464
452
440
428
344
332
320
29
480
463
440
345
322
227
204
180
160
152
480
480
480
466
454
443
432
420
336
324
30
480
464
442
420
327
304
210
187
162
155
480
480
480
467
456
445
434
423
340
328
31
480
466
445
424
331
309
215
193
165
157
480
480
480
480
458
448
437
426
343
332
32
480
480
447
427
334
313
220
199
167
160
480
480
480
480
460
450
440
429
346
336
Specifications
Liebert® APS™
Liebert® APS™
76
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
78
39
25
18
14
11
9
7
6
2
Load
Level 1
90
41
26
19
14
11
9
7
6
5
154
92
53
44
35
27
23
20
17
15
3
136
67
44
32
25
20
16
14
11
10
216
138
99
72
52
46
40
34
28
26
4
160
98
62
46
37
28
25
20
18
15
327
161
133
104
80
67
52
47
43
38
5
199
126
81
60
47
40
33
27
23
20
422
203
153
132
107
91
74
64
51
48
6
300
143
104
76
53
47
41
35
28
26
438
303
166
148
131
109
96
79
70
61
7
320
156
124
95
72
53
48
43
37
32
449
323
203
160
145
131
110
99
82
75
8
336
165
138
108
83
70
52
48
43
39
457
338
224
184
156
143
130
111
101
92
9
420
195
148
125
100
79
67
52
48
44
464
422
312
205
165
153
141
129
112
103
10
429
213
157
136
110
95
76
65
52
48
480
431
326
222
191
161
150
140
129
113
11
437
227
163
144
126
104
83
74
64
52
480
439
336
307
207
167
158
148
138
129
12
444
311
184
152
134
112
98
80
71
62
480
445
345
319
221
195
164
155
146
137
13
449
321
199
158
142
126
106
94
78
69
480
451
425
328
304
208
184
161
153
145
14
454
330
211
163
148
133
113
101
83
75
480
455
431
337
314
220
197
166
158
151
15
458
338
222
180
154
140
126
107
96
81
480
459
437
344
323
302
209
188
163
156
16
462
344
303
192
159
146
132
113
103
92
480
463
442
422
331
311
219
199
167
161
17
465
422
311
202
163
151
138
126
108
99
480
466
446
427
337
319
300
209
190
165
18
# Battery Strings
480
427
319
212
167
155
143
131
113
104
480
480
450
432
343
326
308
218
200
183
19
480
432
325
220
188
159
148
137
125
109
480
480
453
437
420
332
315
226
209
193
20
480
436
331
300
197
163
152
141
130
113
480
480
457
441
425
337
322
306
218
202
21
10-bay, single-phase, no transformer unit Type F (& UPS model number digit 6 = F)
480
440
336
307
205
166
156
146
135
125
480
480
459
444
429
343
327
312
225
210
22
480
443
341
313
213
184
159
150
140
130
480
480
462
447
433
347
333
318
304
217
23
480
446
346
318
220
192
163
153
144
134
480
480
464
450
437
423
338
324
310
224
24
480
449
422
324
226
200
165
156
147
138
480
480
466
453
440
427
342
329
315
302
25
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
10 kVA /
9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 34
454
480
480
429
333
309
213
189
162
154
145
480
480
480
458
446
434
422
337
325
313
27
452
426
328
304
207
181
159
151
142
480
480
480
456
443
431
346
333
320
308
26
480
457
432
337
314
219
195
165
157
149
480
480
480
460
449
437
425
341
329
318
28
480
459
435
341
319
224
202
167
159
151
480
480
480
462
451
440
428
345
334
322
29
480
461
438
344
323
301
207
185
162
154
480
480
480
464
453
442
431
420
337
327
30
480
463
441
420
327
306
213
191
164
157
480
480
480
466
455
445
434
424
341
330
31
-
-
-
-
-
-
-
-
-
-
480
480
480
467
457
447
437
427
344
334
32
Specifications
15 38
19 46
27 64 106 140 159 189 215 307 322 334 344 424 431 437 443 447 451 455 458 461 463 466 480 480 480 480 480 480 480 480 480 480 480 480 480
43 102 147 180 219 316 334 420 431 439 446 452 457 461 465 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
96 164 308 342 434 448 457 465 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
67
47
38
30
25
21
18
16
79
61
48
42
36
30
26
81
69
52
48
44
81
72
63
90
76
94 100 105 110 121 126 131 135 139 143 146 149 152 155 158 160 162 164 166 181
97 104 109 120 126 131 136 140 144 148 151 154 157 160 162 165 167 184 189 195 200
82
95 102 108 120 127 132 138 142 147 150 154 157 160 163 165 180 187 193 199 204 209 214 219
78
70
91 100 107 120 127 134 140 145 149 153 157 161 164 166 184 191 198 204 210 215 220 225 302 306 310
74
64
52
97 106 120 128 136 142 148 152 157 161 164 180 188 196 204 210 217 222 300 305 309 314 318 321 325 328
77
66
52
49
92 103 113 129 137 145 151 156 161 165 183 193 202 210 217 224 302 308 313 318 322 327 331 334 338 341 344 347
72
53
48
44
39
99 111 129 140 148 155 161 166 188 199 209 218 226 306 312 318 324 329 333 337 341 345 420 424 427 429 432 434 437
75
60
48
43
38
33
91 109 130 143 153 160 167 194 208 219 301 310 318 325 331 337 342 347 423 427 430 434 437 439 442 444 447 449 451 453 455
64
48
41
33
27
23
21
73 105 132 149 161 186 206 223 308 320 329 337 344 423 428 433 437 441 445 448 451 454 456 458 460 462 464 466 480 480 480 480 480
46
34
26
21
17
14
12
10
77
80
53
45
38
30
26
79
62
48
42
36
30
26
35
79
64
50
45
40
39
43
78
65
51
47
46
90
72
60
50
48
51
82
72
61
53
63
81
72
68
92
76
72
76
90
80
95
83
93
98 101 105 108 111 120 124 127 131 134
99 103 107 111 120 124 128 131 134 137 140 143
97 102 106 110 120 124 129 132 136 139 142 145 148 150 153
80
94 100 105 110 120 125 130 134 138 141 145 148 151 153 156 158 161 163
77
67
97 103 109 120 126 131 136 140 144 148 151 154 157 160 162 164 167 183 189 194
77
66
52
92 100 107 113 126 132 138 143 147 151 155 158 161 164 167 184 190 197 203 208 213 218 222
72
53
48
44
94 104 112 126 133 140 146 151 155 159 163 166 184 192 200 207 213 219 224 301 306 311 315 319 322
71
52
46
41
35
30
98 109 125 135 143 150 156 161 165 184 195 204 212 220 227 305 311 316 321 326 330 334 337 341 344 347 422
70
50
44
37
30
26
22
-
-
-
-
-
-
-
-
-
-
53
39
27
20
16
13
11
9
8
74
46
35
26
21
17
14
11
10
67
47
39
30
25
21
18
16
77
52
44
36
28
25
20
18
72
51
45
38
31
26
23
79
62
48
42
36
28
26
75
60
48
43
37
32
81
66
51
46
41
36
92
72
53
48
43
39
81
69
52
48
44
92
73
61
50
46
81
70
54
50
91
74
64
52
81
71
62
90
75
66
94
78
69
83
76
93
78
83
93
96
99
97 100 103 106 109
81
98 102 105 108 111 120 123 126
81
73
96 100 104 107 111 120 124 127 131 134 137 140
78
68
53
97 102 106 110 120 124 128 132 136 139 142 145 148 150 153
77
66
52
48
98 104 109 113 124 129 134 138 142 145 148 151 154 157 159 161 163 165
77
64
50
46
42
92 100 106 112 124 130 135 140 144 148 152 155 158 161 164 166 182 189 195 200 205 210
69
51
45
40
34
28
92 101 109 123 131 138 143 149 153 157 161 164 167 188 195 202 209 215 221 226 303 307 311 315 319
64
48
41
33
27
23
21
92 105 122 133 142 150 156 161 166 187 198 208 217 224 303 310 315 321 326 330 334 338 342 345 421 423 426 429
52
42
32
26
21
18
14
13
99 127 144 157 166 197 214 300 312 322 331 339 345 423 428 433 437 441 444 447 450 453 455 457 459 461 463 465 466 480 480
45
27
20
15
12
9
8
6
5
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
-
-
-
-
-
-
-
67
47
39
30
25
21
22
19
82 105 126 139 149 158 164 187 201 213 224 305 313 320 327 333 338 343 347 423 427 430 433 436 439 442 444 446 448 450
50
40
28
23
19
16
18
16
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Tables for UPS Model Number Where Digits 1-3 are AS2 or ASB
-
63
41
28
22
18
14
12
14
12
7.2.1
-
8
10
99 133 152 166 202 223 312 325 336 345 424 431 436 441 446 450 453 456 459 462 464 466 480 480 480 480 480 480 480 480 480 480
44
27
20
15
12
9
8
6
5
Estimated Battery Run Times
-
-
-
-
-
-
-
-
-
-
-
98 143 165 213 311 330 344 427 436 443 449 454 459 463 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
44
27
20
15
12
9
8
6
5
95 112 134 146 156 163 186 201 215 226 307 316 323 330 336 341 346 423 427 430 434 437 440 443 445 447 450 452 454 455 457
99 113 133 144 153 160 166 190 203 214 224 305 312 319 325 331 336 341 345 421 425 428 431 434 437 439 442 444 446 448
81 102 120 132 142 150 157 163 180 193 204 214 222 302 309 316 321 327 332 336 340 344 420 423 426 429 432 434 437 439
90 111 136 149 160 180 199 215 300 311 320 329 336 342 420 425 429 433 437 441 444 447 449 452 454 456 458 460 462 463 465 466
70
77
66
77 109 137 153 164 195 215 302 315 326 335 343 421 427 432 437 441 445 448 451 454 457 459 461 463 465 467 480 480 480 480 480 480
60
48
53
48
7.2
20kVA /
18kW
15kVA /
13.5 kW
10kVA
/9kW
5kVA /
4.5kW
11 28
42
36
93 105 120 130 139 146 152 157 162 166 186 196 205 213 220 226 304 310 315 320 324 328 332 336 339 342 345 420
90 103 120 131 140 148 154 160 165 183 194 204 213 221 300 307 313 318 323 328 332 336 340 343 346 421 424 427 429
76
60%
25
21
72
63
# Battery Strings
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
9
52
48
9
8
44
39
8
70%
30
26
7
80%
18
16
6
6
5
5
4
90%
3
100%
2
16-bay, single-phase, no transformer unit Type N (& UPS model number digit 6 = N)
UPS
Load
Rating Level 1
Table 35
Specifications
Liebert® APS™
Liebert® APS™
78
14
15
16
17
18
19
20
# Battery Strings
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
110 131 144 153 161 180 196 209 221 303 312 319 326 332 338 343 420 424 428 431 434 437 440 443 445 447 450 452 453 455
111 130 141 150 158 164 184 198 209 219 300 308 315 322 328 333 338 342 346 422 425 429 432 434 437 439 442 444 446
111 129 139 148 155 161 166 187 199 209 218 226 305 312 318 323 328 333 337 341 345 420 423 426 429 432 434 437
101 112 129 138 146 152 158 163 167 190 200 209 217 225 303 309 315 320 325 329 333 337 341 344 347 422 425 427
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
104 112 126 133 140 146 151 155 159 163 166 184 192 200 207 213 219 224 302 306 311 315 319 322
108 125 136 144 152 158 163 180 192 202 212 220 300 306 313 318 324 328 333 337 341 344 420 423 426 428 431
125 143 156 165 194 212 227 311 321 330 337 344 422 427 432 436 440 443 446 449 452 454 456 459 461 462 464 466 467 480
-
-
-
-
-
-
-
-
-
-
92
42
27
19
15
11
9
7
6
5
8
78
49
39
28
23
19
16
14
12
77
52
45
37
28
25
21
19
95
67
50
43
36
28
26
22
92
69
51
46
40
35
30
90
70
53
48
43
39
98
77
64
51
47
43
95
77
65
52
48
93
76
66
53
99
80
71
63
96
80
72
94
79
99
83
93
97
101 105 108 111 120 124 127 130 133
103 107 110 113 123 127 130 134 137 140 142
101 105 109 113 123 128 131 135 138 141 144 147 150 152
83
76
104 109 113 124 129 133 137 140 144 147 150 153 155 157 160 162
91
76
67
102 107 112 124 129 134 139 143 146 150 153 156 159 161 163 166 180 186 191
81
71
61
51
105 111 124 130 136 141 145 150 153 157 160 163 165 180 187 193 199 205 210 215 220
83
71
53
49
46
101 109 123 131 138 143 149 153 157 161 164 167 188 195 203 209 215 221 226 303 307 311 315 319
77
63
50
45
40
35
106 122 132 140 147 153 158 163 167 189 198 207 215 222 300 306 312 317 322 326 330 334 337 341 344 347
77
60
48
42
35
28
26
101 121 135 145 154 161 167 193 205 216 226 307 314 321 327 333 338 342 347 422 426 429 432 435 438 440 443 445 447
64
46
38
28
25
20
18
16
95
43
27
19
15
11
9
7
6
5
71
45
33
26
20
17
14
11
10
83
51
41
31
25
20
17
14
13
75
51
43
35
28
23
20
18
83
62
47
40
33
27
23
21
98
70
51
44
38
31
26
23
83
67
51
45
39
34
28
97
73
53
48
43
37
32
90
70
53
48
43
39
96
75
62
50
46
42
90
72
61
50
46
95
76
65
52
48
90
74
63
52
94
77
67
53
99
80
71
62
93
78
69
97
81
73
93
78
96
81
83
93
96
100 103 105
101 104 107 110 113 122
83
76
103 106 110 113 122 126 129 133 136
83
75
66
100 104 109 112 122 127 130 134 137 141 143 146 149
80
70
53
50
102 107 111 122 127 131 136 139 143 146 149 152 155 157 160 162
80
68
52
48
44
104 109 121 127 133 138 142 146 150 153 156 159 162 164 167 184 190 195 201
79
65
50
45
41
36
107 120 128 134 141 146 151 155 159 162 165 182 190 197 204 210 216 221 226 303 307 311
77
60
48
42
35
28
26
102 113 130 139 147 153 159 164 180 192 202 211 219 226 305 311 316 321 326 330 334 338 342 345 420 423
65
46
38
28
25
20
18
16
122 140 153 163 189 207 222 307 317 326 334 341 347 424 429 433 437 441 444 447 450 452 455 457 459 461 463 464 466
52
37
26
20
16
13
10
9
8
-
-
-
-
-
-
-
-
-
-
126 147 161 190 213 302 316 328 338 346 425 431 436 441 445 449 452 455 458 460 463 465 467 480 480 480 480 480 480 480 480
53
40
27
22
18
14
11
10
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
90%
98
104 109 120 125 130 134 138 142 145 149 152 154 157 159 162 164 166
135 159 199 227 320 335 347 429 437 443 449 454 458 461 465 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
67
99
100%
83
41
95
93
103 108 113 125 131 135 140 144 147 151 154 157 159 162 164 166 182 188 193
104 124 138 148 156 163 184 198 211 221 303 311 318 325 331 336 341 346 422 425 429 432 435 438 440 443 445 447 449
76
97
81
101 108 113 126 132 137 142 146 150 153 157 160 162 165 167 185 192 197 203 208 213
83
76
106 113 126 133 138 144 148 152 156 160 163 166 182 189 196 202 208 213 218 223 300 304
94
78
69
-
80
60
95
99
81
71
62
100 110 126 134 142 148 154 159 163 167 187 197 205 213 219 226 304 309 314 319 323 327 331 334 338 341
79
90
74
64
52
-
62
46
83
70
76
66
52
48
10%
44
32
72
53
68
52
48
44
20%
26
19
53
47
53
48
43
39
-
47
40
48
43
37
32
-
37
28
42
36
28
26
30%
25
20
33
27
23
21
40%
14
11
25
20
18
16
-
17
14
11
10
-
9
7
6
5
50%
136 160 199 300 320 336 420 429 437 444 449 454 458 462 465 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
133 153 166 202 223 312 325 336 345 424 431 437 441 446 450 453 456 459 462 464 466 480 480 480 480 480 480 480 480 480 480 480
104 132 149 161 185 206 222 308 319 329 337 344 422 428 433 437 441 445 448 451 453 456 458 460 462 464 466 467 480 480 480 480
60%
90
99
73
13
108 132 146 157 165 192 208 222 305 315 324 331 338 344 421 426 430 434 437 441 444 446 449 451 454 456 458 459 461 463 464
92
12
-
38
20%
53
44
81
68
96
99
82
11
103 113 129 137 145 151 156 161 165 183 193 202 210 218 224 302 308 313 318 323 327 331 334 338 341 344 347
10
-
25
30%
52
46
74
79
70
92
9
70%
18
40%
36
28
52
63
51
75
8
80%
14
50%
40
47
43
61
7
-
11
60%
23
34
28
48
6
-
9
70%
20
17
38
5
90%
7
80%
26
4
73 149 207 320 345 433 445 454 461 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
6
90%
15
3
10%
5
100%
2
100%
1
Load
Level
16-bay, single-phase, no transformer unit Type R (& UPS model number digit 6 = R)
Note: Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
20 kVA /
18 kW
15 kVA /
13.5 kW
10 kVA /
9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 36
Specifications
79
27
28
29
30
31
32
33
34
35
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
-
-
30%
-
-
40%
10%
-
50%
20%
-
60%
-
-
70%
-
-
80%
30%
-
90%
40%
-
-
10%
100%
96 164 308 342 434 448 457 465 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
26
43 102 147 180 219 316 334 420 431 439 446 452 457 461 465 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
25
-
24
-
23
20%
22
30%
21
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
27
19
15
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
98
44
27
20
15
12
9
8
6
5
64
46
38
42
53
77
99
113 133 144 153 160 166 190 203 214 224 305 312 319 325 331 336 341 345 421 425 428 431 434 437 439 442 444 446
112 134 146 156 163 186 201 215 226 307 316 323 330 336 341 346 423 427 430 434 437 440 443 445 447 450 452 454 455
111 136 149 160 180 199 215 300 311 320 329 336 342 420 425 429 433 437 441 444 447 449 452 454 456 458 460 462 463 465
95
109 137 153 164 195 215 302 315 326 335 343 421 427 432 437 441 445 448 451 454 457 459 461 463 465 467 480 480 480 480 480
90
70
103 120 131 140 148 154 160 165 183 194 204 213 221 300 307 313 318 323 328 332 336 340 343 346 421 424 427
91
64
48
41
33
27
23
21
99
75
60
48
43
38
33
97
77
66
52
49
95
78
70
97
82
94
100 105 110 121 126 131 135 139 143 146 149 152 155 158 160 162 164 166
104 109 120 126 131 136 140 144 148 151 154 157 160 162 165 167 184 189 195
102 108 120 127 132 138 142 147 150 154 157 160 163 165 180 187 193 199 204 209 214
90
76
100 107 120 127 134 140 145 149 153 157 161 164 166 184 191 198 204 210 215 220 225 302 306
81
72
63
106 120 128 136 142 148 152 157 161 164 180 188 196 204 210 217 222 300 305 309 314 318 321 325
91
74
64
52
103 113 129 137 145 151 156 161 165 183 193 202 210 217 224 302 308 313 318 322 327 331 334 338 341 344
81
69
52
48
44
111 129 140 148 155 161 166 188 199 209 218 226 306 312 318 324 329 333 337 341 345 420 424 427 429 432 434
92
72
53
48
44
39
109 130 143 153 160 167 194 208 219 301 310 318 325 331 337 342 347 423 427 430 434 437 439 442 444 447 449 451 453
79
61
48
42
36
30
26
105 132 149 161 186 206 223 308 320 329 337 344 423 428 433 437 441 445 448 451 454 456 458 460 462 464 466 480 480 480 480
67
47
38
30
25
21
18
16
-
-
-
-
-
-
-
-
-
-
99
44
27
20
15
12
9
8
6
5
82
50
40
28
23
19
16
14
12
80
53
45
38
30
26
22
19
98
70
50
44
37
30
26
22
94
71
52
46
41
35
30
92
72
53
48
44
39
90
72
60
50
46
97
77
66
52
48
94
77
67
53
92
76
68
97
80
72
95
80
99
83
93
98
101 105 108 111 120 124 127 131
103 107 111 120 124 128 131 134 137 140
102 106 110 120 124 129 132 136 139 142 145 148 150
90
76
100 105 110 120 125 130 134 138 141 145 148 151 153 156 158 161
81
72
63
103 109 120 126 131 136 140 144 148 151 154 157 160 162 164 167 183 189
82
72
61
51
100 107 113 126 132 138 143 147 151 155 158 161 164 167 184 190 197 203 208 213 218
78
65
51
47
43
104 112 126 133 140 146 151 155 159 163 166 184 192 200 207 213 219 224 301 306 311 315 319
79
64
50
45
40
35
109 125 135 143 150 156 161 165 184 195 204 212 220 227 305 311 316 321 326 330 334 337 341 344 347
79
62
48
42
36
30
26
105 126 139 149 158 164 187 201 213 224 305 313 320 327 333 338 343 347 423 427 430 433 436 439 442 444 446 448
67
47
39
30
25
21
18
16
99
45
27
20
15
12
9
8
6
5
74
46
35
26
21
17
14
11
10
92
52
42
32
26
21
18
14
13
77
52
44
36
28
25
20
18
92
64
48
41
33
27
23
21
79
62
48
42
36
28
26
92
69
51
45
40
34
28
81
66
51
46
41
36
92
72
53
48
43
39
98
77
64
50
46
42
92
73
61
50
46
97
77
66
52
48
91
74
64
52
96
78
68
53
90
75
66
94
78
69
98
81
73
93
78
97
81
83
93
96
100 103 106
102 105 108 111 120 123
83
76
100 104 107 111 120 124 127 131 134 137
81
71
62
102 106 110 120 124 128 132 136 139 142 145 148 150
81
70
54
50
104 109 113 124 129 134 138 142 145 148 151 154 157 159 161 163
81
69
52
48
44
100 106 112 124 130 135 140 144 148 152 155 158 161 164 166 182 189 195 200 205
75
60
48
43
37
32
101 109 123 131 138 143 149 153 157 161 164 167 188 195 202 209 215 221 226 303 307 311 315
72
51
45
38
31
26
23
105 122 133 142 150 156 161 166 187 198 208 217 224 303 310 315 321 326 330 334 338 342 345 421 423 426
67
47
39
30
25
21
18
16
127 144 157 166 197 214 300 312 322 331 339 345 423 428 433 437 441 444 447 450 453 455 457 459 461 463 465 466 480
53
39
27
20
16
13
11
9
8
133 152 166 202 223 312 325 336 345 424 431 436 441 446 450 453 456 459 462 464 466 480 480 480 480 480 480 480 480 480
63
41
28
22
18
14
12
10
8
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
143 165 213 311 330 344 427 436 443 449 454 459 463 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
73
46
34
26
21
17
14
12
10
106 140 159 189 215 307 322 334 344 424 431 437 443 447 451 455 458 461 463 466 480 480 480 480 480 480 480 480 480 480 480 480
77
60
48
20
102 120 132 142 150 157 163 180 193 204 214 222 302 309 316 321 327 332 336 340 344 420 423 426 429 432 434 437
90
19
-
25
28
81
72
18
40%
9
11
66
52
17
50%
# Battery Strings
-
48
44
16
-
36
30
15
105 120 130 139 146 152 157 162 166 186 196 205 213 220 226 304 310 315 320 324 328 332 336 339 342 345
14
60%
21
18
93
13
70%
8
6
76
12
-
63
11
-
48
10
80%
39
9
90%
26
8
16
5
7
-
6
100%
5
3
Load
Level 1 2
4
16-bay, single-phase, no transformer unit Type B (& UPS model number digit 6 = B)
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
20 kVA /
18 kW
15 kVA /
13.5 kW
10 kVA /
9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 37
Specifications
Liebert® APS™
Liebert® APS™
80
-
-
-
- 11
- 14
- 18
- 25
- 38
90%
80%
70%
60%
50%
40%
30%
20%
11
12
13
14
15
16
17
18
19
20
# Battery Strings
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
111 129 139 148 155 161 166 187 199 209 218 226 305 312 318 323 328 333 337 341 345 420 423 426 429 432 434
101 112 129 138 146 152 158 163 167 190 200 209 217 225 303 309 315 320 325 329 333 337 341 344 347 422 425
103 113 129 137 145 151 156 161 165 183 193 202 210 218 224 302 308 313 318 323 327 331 334 338 341 344
10
111 130 141 150 158 164 184 198 209 219 300 308 315 322 328 333 338 342 346 422 425 429 432 434 437 439 442 444
99
82
92
9
110 131 144 153 161 180 196 209 221 303 312 319 326 332 338 343 420 424 428 431 434 437 440 443 445 447 450 452 453
96
79
70
75
8
108 132 146 157 165 192 208 222 305 315 324 331 338 344 421 426 430 434 437 441 444 446 449 451 454 456 458 459 461 463
92
74
63
51
61
7
133 153 166 202 223 312 325 336 345 424 431 437 441 446 450 453 456 459 462 464 466 480 480 480 480 480 480 480 480 480 480
104 132 149 161 185 206 222 308 319 329 337 344 422 428 433 437 441 445 448 451 453 456 458 460 462 464 466 467 480 480 480
81
68
52
47
43
48
6
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
83
41
98
95
108 125 136 144 152 158 163 180 192 202 212 220 300 306 313 318 324 328 333 337 341 344 420 423 426 428
125 143 156 165 194 212 227 311 321 330 337 344 422 427 432 436 440 443 446 449 452 454 456 459 461 462 464 466 467
104 124 138 148 156 163 184 198 211 221 303 311 318 325 331 336 341 346 422 425 429 432 435 438 440 443 445 447
76
104 112 126 133 140 146 151 155 159 163 166 184 192 200 207 213 219 224 302 306 311 315 319
-
-
-
-
-
-
-
-
-
-
92
42
27
19
15
11
9
7
6
5
78
49
39
28
23
19
16
14
12
77
52
45
37
28
25
21
19
95
67
50
43
36
28
26
22
92
69
51
46
40
35
30
90
70
53
48
43
39
98
77
64
51
47
43
95
77
65
52
48
93
76
66
53
99
80
71
63
96
80
72
94
79
99
83
93
97
101 105 108 111 120 124 127 130
103 107 110 113 123 127 130 134 137 140
101 105 109 113 123 128 131 135 138 141 144 147 150
83
76
104 109 113 124 129 133 137 140 144 147 150 153 155 157 160
91
76
67
102 107 112 124 129 134 139 143 146 150 153 156 159 161 163 166 180 186
81
71
61
51
105 111 124 130 136 141 145 150 153 157 160 163 165 180 187 193 199 205 210 215
83
71
53
49
46
101 109 123 131 138 143 149 153 157 161 164 167 188 195 203 209 215 221 226 303 307 311 315
77
63
50
45
40
35
106 122 132 140 147 153 158 163 167 189 198 207 215 222 300 306 312 317 322 326 330 334 337 341 344
77
60
48
42
35
28
26
101 121 135 145 154 161 167 193 205 216 226 307 314 321 327 333 338 342 347 422 426 429 432 435 438 440 443 445
64
46
38
28
25
20
18
16
95
43
27
19
15
11
9
7
6
5
71
45
33
26
20
17
14
11
10
83
51
41
31
25
20
17
14
13
75
51
43
35
28
23
20
18
83
62
47
40
33
27
23
21
98
70
51
44
38
31
26
23
83
67
51
45
39
34
28
97
73
53
48
43
37
32
90
70
53
48
43
39
96
75
62
50
46
42
90
72
61
50
46
95
76
65
52
48
90
74
63
52
94
77
67
53
99
80
71
62
93
78
69
97
81
73
93
78
96
81
83
93
100 103
101 104 107 110 113
83
76
103 106 110 113 122 126 129 133
83
75
66
100 104 109 112 122 127 130 134 137 141 143 146
80
70
53
50
102 107 111 122 127 131 136 139 143 146 149 152 155 157 160
80
68
52
48
44
104 109 121 127 133 138 142 146 150 153 156 159 162 164 167 184 190 195
79
65
50
45
41
36
107 120 128 134 141 146 151 155 159 162 165 182 190 197 204 210 216 221 226 303 307
77
60
48
42
35
28
26
102 113 130 139 147 153 159 164 180 192 202 211 219 226 305 311 316 321 326 330 334 338 342 345 420
65
46
38
28
25
20
18
16
122 140 153 163 189 207 222 307 317 326 334 341 347 424 429 433 437 441 444 447 450 452 455 457 459 461 463 464
52
37
26
20
16
13
10
9
8
-
-
-
-
-
-
-
-
-
-
126 147 161 190 213 302 316 328 338 346 425 431 436 441 445 449 452 455 458 460 463 465 467 480 480 480 480 480 480 480
53
40
27
22
18
14
11
10
8
135 159 199 227 320 335 347 429 437 443 449 454 458 461 465 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
67
80
60
95
101 108 113 126 132 137 142 146 150 153 157 160 162 165 167 185 192 197 203 208
100 110 126 134 142 148 154 159 163 167 187 197 205 213 219 226 304 309 314 319 323 327 331 334 338
79
94
106 113 126 133 138 144 148 152 156 160 163 166 182 189 196 202 208 213 218 223 300
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
62
46
83
70
99
81
104 109 120 125 130 134 138 142 145 149 152 154 157 159 162 164
103 108 113 125 131 135 140 144 147 151 154 157 159 162 164 166 182 188
99
-
44
32
72
53
90
74
97
93
10%
26
19
53
47
76
66
83
81
20%
-
-
47
40
68
52
78
76
-
37
28
53
48
71
69
-
25
20
48
43
64
62
30%
14
11
42
36
52
52
40%
-
-
33
27
48
48
-
25
20
43
44
-
17
14
37
39
50%
9
7
28
32
60%
-
-
23
26
-
18
21
-
11
16
70%
6
10
80%
-
5
-
90%
-
- 73 149 207 320 345 433 445 454 461 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
-
136 160 199 300 320 336 420 429 437 444 449 454 458 462 465 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
99
73
52
46
40
34
28
38
5
10%
90
53
44
36
28
23
20
26
4
100%
9
7
6
17
15
-
100%
5
3
Load
Level 1 2
16-bay, single-phase, no transformer unit Type F (& UPS model number digit 6 = F)
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
20 kVA
/ 18 kW
15 kVA
/ 13.5 kW
10 kVA
/ 9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 38
Specifications
81
-
-
-
-
-
-
-
-
-
-
-
-
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
-
-
-
-
-
-
-
-
-
-
83
41
26
19
14
11
105 133 149 161 186 207 223 309 320 330 338 345 423 428 433 438 441 445 448 451 454 456 459 461 463 464 466 480 480 480
98
62
46
37
28
23
20
17
15
95
72
53
47
42
37
31
94
75
64
51
48
97
79
70
61
99
82
74
91
97
103 108 112 123 128 133 137 140 144 147 150 153 156 158 160 163
101 107 112 123 129 134 138 142 146 149 152 155 158 161 163 165 167 185
106 112 124 130 135 140 144 148 152 155 158 161 164 166 182 189 194 200 205
95
80
105 112 125 131 137 142 147 151 155 159 162 165 167 187 193 200 206 211 216 221 226
92
76
68
103 111 125 133 139 145 150 155 159 162 166 183 191 199 206 212 218 224 301 305 310 314 318
83
72
62
51
100 110 126 134 142 148 154 159 163 167 188 197 205 213 220 226 304 309 314 319 323 327 331 334 338
79
66
52
47
43
108 126 136 145 152 158 163 181 193 203 213 221 300 307 313 319 324 329 333 338 341 345 420 423 426 429
83
69
52
47
43
38
104 125 138 149 157 164 185 200 212 223 304 312 319 326 332 337 342 346 422 426 430 433 436 438 441 443 446 448
76
53
47
41
35
28
26
126 143 156 165 195 213 227 311 322 330 338 344 422 427 432 436 440 443 447 449 452 455 457 459 461 463 464 466 467
81
60
47
39
32
27
23
20
97
43
27
19
14
11
9
7
6
5
79
49
38
28
23
18
16
13
11
77
52
44
36
28
25
21
18
95
67
49
42
35
28
25
22
91
68
51
45
40
34
28
83
69
52
47
43
38
97
76
63
50
46
42
94
75
64
51
47
91
75
65
52
97
79
70
60
95
78
70
99
82
74
97
81
91
95
99
102 106 109 112 121 125
101 105 108 112 121 125 129 132 135
104 108 112 122 126 130 133 137 140 143 146
92
78
102 107 111 122 127 131 135 139 142 145 148 151 154 156
83
74
65
100 106 111 122 128 133 137 141 145 148 152 155 157 160 162 165 167
80
70
53
50
104 110 122 129 134 139 144 148 152 155 159 162 164 167 184 191 197 202 208
81
69
53
49
45
100 109 122 130 137 143 148 152 157 160 164 167 186 194 201 207 213 219 224 301 306 310
76
61
49
44
39
34
106 122 132 140 147 153 158 163 167 188 198 207 215 222 300 306 312 317 321 326 330 334 337 341
76
53
47
41
35
28
26
102 123 136 147 155 162 181 196 208 219 301 309 316 323 329 335 340 344 420 424 428 431 434 437 439 442 444
64
46
37
28
23
20
17
15
131 151 164 199 220 309 322 333 343 422 429 435 440 444 448 452 455 458 460 463 465 467 480 480 480 480 480 480 480
60
40
27
21
17
14
11
9
8
-
-
-
-
-
-
-
-
-
-
135 159 197 226 319 335 347 428 436 443 448 453 457 461 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
67
44
33
25
20
16
13
11
10
141 164 208 308 327 342 425 434 441 448 453 457 461 465 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
-
-
50%
109 131 143 153 161 167 195 209 220 302 311 319 326 332 338 343 347 423 427 431 434 437 440 442 445 447 449 451
Tables for UPS model number digits 1-3 are AS3 or ASC
-
-
60%
9
7
92
108 132 146 157 165 192 208 222 305 315 324 331 338 344 421 426 430 434 437 441 444 446 449 451 453 456 457 459 461
101 135 154 167 206 227 315 328 338 347 427 433 438 443 448 451 455 458 460 463 465 467 480 480 480 480 480 480 480 480 480
73
81
67
7.3.1
10%
-
6
5
96
53
44
52
46
111 129 139 148 155 160 166 187 198 209 218 226 305 312 318 323 328 333 337 341 345 420 423 426 429 432
Estimated Battery Run Times
20%
-
33
70%
32
80%
31
-
30
-
29
90%
28
100%
27
82 158 225 333 427 442 453 460 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
26
40
25
10%
24
20%
23
25
22
18
21
30%
20
110 130 141 150 157 164 184 197 209 219 300 308 315 321 327 332 337 342 346 422 425 428 431 434 437 439 441
99
19
40%
36
27
96
79
18
14
74
63
17
11
52
47
16
102 112 127 136 143 150 155 160 164 181 191 200 208 215 222 300 306 311 316 321 325 329 333 336 343
15
101 111 128 137 145 152 158 163 167 189 199 208 216 224 302 309 314 319 324 329 333 337 340 343 347 421
90
14
50%
40
34
82
74
13
60%
23
20
69
60
12
9
51
47
11
7
42
38
10
70%
28
26
9
80%
17
8
15
7
6
6
5
5
90%
4
100%
3
2
Load
Level 1
# Battery Strings
12-bay, single-phase, transformer-based unit Type N (& UPS model number 6 = N)
7.3
15 kVA /
13.5 kW
10 kVA /
9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 39
Specifications
Liebert® APS™
Liebert® APS™
82
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
33
-
32
-
31
70%
30
80%
29
-
28
-
27
90%
26
100%
25
71 147 203 317 342 431 443 452 459 465 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
24
35
23
10%
22
20%
21
22
20
16
-
-
-
-
-
-
-
-
-
-
75
38
25
18
14
11
9
7
6
5
79
50
41
125 142 155 165 193 211 226 310 320 329 337 343 421 426 431 435 439 443 446 449 451 454 456 458 460 462 464 465 467
125 147 161 190 212 302 316 328 337 346 425 431 436 441 445 448 452 455 458 460 462 465 467 480 480 480 480 480 480 480
97
105 126 139 149 157 164 186 200 213 223 304 313 320 326 332 338 342 347 423 426 430 433 436 439 441 444 446 448
107 126 138 147 155 161 167 190 203 213 222 303 310 317 323 328 333 338 342 346 422 425 428 431 434 436 439
102 125 140 152 161 180 197 212 224 307 316 324 331 337 343 420 424 428 432 436 439 442 445 447 449 452 454 456 457
81
109 126 135 143 150 156 161 165 185 195 205 213 221 227 306 311 317 322 326 330 334 338 341 344 347
108 126 137 145 152 158 164 182 193 204 213 222 301 308 314 320 325 330 334 338 342 345 421 424 426 429
91
53
44
36
27
23
19
17
15
91
70
52
47
41
36
31
98
77
65
51
47
43
95
78
69
60
98
81
74
90
96
102 107 112 122 127 132 136 140 143 147 150 152 155 158 160
100 106 111 122 127 132 137 141 145 148 151 154 157 160 162 164 166
105 110 122 128 134 139 143 147 151 154 157 160 163 165 167 186 192 197
93
79
103 110 123 129 135 141 145 150 154 157 160 163 166 183 190 196 202 208 213 218
90
75
67
101 109 123 131 137 143 148 153 157 161 164 167 187 195 202 208 214 220 225 302 307 311
81
71
61
51
108 122 132 139 146 152 157 161 165 182 192 200 208 215 222 300 305 310 315 319 324 327 331
91
74
63
51
47
105 121 132 141 149 155 161 165 186 197 206 215 223 302 308 314 320 325 329 333 337 341 344 420 423
81
67
51
47
42
38
100 120 134 144 153 160 166 191 204 215 225 305 313 320 326 332 337 341 346 421 425 428 432 434 437 440 442
73
52
46
40
34
28
26
112 137 150 161 182 201 217 302 313 322 330 337 343 421 426 430 434 438 442 445 447 450 452 455 457 459 461 462
77
52
46
38
31
26
22
20
82
41
26
18
14
11
9
7
6
5
75
48
37
27
22
18
16
13
11
97
61
45
36
28
23
20
17
15
91
65
49
42
35
28
25
22
83
67
51
45
39
34
28
99
75
60
49
43
38
33
95
75
62
50
46
41
93
74
63
51
47
99
79
69
53
50
96
78
69
60
93
78
70
98
81
74
96
81
90
94
98
102 105 109 112 121 124
100 104 108 111 120 124 128 131 134
103 107 111 121 125 129 132 136 139 142 145
91
77
101 106 111 121 126 130 134 138 141 145 148 150 153 155
82
74
65
105 110 121 127 132 136 140 144 148 151 154 157 159 162 164 166
90
74
64
52
103 109 121 127 133 138 143 147 151 155 158 161 163 166 182 188 194 200 206
81
69
52
48
45
107 120 128 135 141 146 151 155 159 162 166 182 190 197 204 210 216 221 226 303 308
82
68
52
47
42
38
103 113 129 137 144 151 156 161 165 183 193 202 210 217 224 302 308 313 318 322 326 330 334 337
75
53
47
40
34
28
26
112 131 142 151 159 165 186 200 211 221 302 310 317 323 329 334 339 343 347 423 426 430 432 435 480 480
75
51
43
36
28
25
21
18
121 143 158 183 206 225 311 323 333 342 421 427 433 438 442 446 449 453 455 458 460 463 465 467 480 480 480 480 480
52
38
27
21
17
13
11
9
8
124 151 167 211 306 323 336 347 428 435 441 447 451 455 459 462 465 467 480 480 480 480 480 480 480 480 480 480 480 480
61
42
30
25
19
16
13
11
10
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
130 155 188 219 313 329 342 424 432 439 445 450 454 458 462 465 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480
91
66
76
63
19
30%
50
44
18
40%
32
26
92
17
13
71
96
16
100 110 126 134 142 148 154 159 163 167 187 197 205 213 219 226 304 309 314 319 323 327 331 334 338
15
10
50
76
98
83
14
50%
39
61
80
72
13
60%
22
46
67
53
12
8
33
50
47
11
70%
19
41
37
10
7
27
25
9
80%
16
8
14
7
5
6
5
5
90%
4
100%
3
2
Load
Level 1
# Battery Strings
12-bay, single-phase, transformer-based unit Type R (& UPS model number 6 = R)
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
15 kVA /
13.5 kW
10 kVA /
9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 40
Specifications
83
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
82
40
25
18
14
11
9
7
6
5
83
41
26
19
14
11
9
7
6
5
158
96
53
44
36
27
23
20
17
15
3
135
67
44
33
25
20
16
13
11
10
225
141
101
73
52
46
40
34
28
26
4
159
98
62
46
37
28
23
20
17
15
333
164
135
105
81
67
52
47
42
38
5
197
126
81
60
47
39
32
27
23
20
427
208
154
133
108
92
74
63
51
47
6
226
143
104
76
53
47
41
35
28
26
442
308
167
149
132
109
96
79
69
60
7
319
156
125
95
72
53
47
42
37
31
453
327
206
161
146
131
110
99
82
74
8
335
165
138
108
83
69
52
47
43
38
460
342
227
186
157
143
130
111
101
90
9
347
195
149
126
100
79
66
52
47
43
467
425
315
207
165
153
141
129
111
102
10
428
213
157
136
110
94
75
64
51
48
480
434
328
223
192
161
150
139
128
112
11
436
227
164
145
126
103
83
72
62
51
480
441
338
309
208
167
157
148
137
127
12
443
311
185
152
134
111
97
79
70
61
480
448
347
320
222
195
164
155
145
136
13
448
322
200
158
142
125
105
92
76
68
480
453
427
330
305
209
184
160
152
143
14
453
330
212
163
148
133
112
99
82
74
480
457
433
338
315
220
197
166
158
150
15
457
338
223
181
154
139
125
106
95
80
480
461
438
345
324
302
209
187
163
155
16
461
344
304
193
159
145
131
112
101
91
480
465
443
423
331
311
219
198
167
160
17
464
422
312
203
163
150
137
124
107
97
480
480
448
428
338
319
300
209
189
164
18
467
427
319
213
167
155
142
130
112
103
480
480
451
433
344
326
308
218
199
181
19
480
432
326
221
188
159
147
135
123
108
480
480
455
438
421
332
315
226
208
191
20
480
436
332
300
197
162
151
140
129
112
480
480
458
441
426
338
321
305
216
200
21
480
440
337
307
205
166
155
144
134
123
480
480
460
445
430
343
327
312
224
208
22
480
443
342
313
213
183
159
148
138
128
480
480
463
448
434
347
332
318
302
215
23
480
447
346
319
220
191
162
152
142
133
480
480
465
451
437
423
337
323
309
222
24
480
449
422
324
226
199
165
155
146
137
480
480
467
454
441
427
342
328
314
300
25
480
452
426
329
304
206
167
158
149
140
480
480
480
456
444
431
346
333
319
306
26
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
10 kVA /
9 kW
5 kVA /
4.5 kW
-
100%
2
# Battery Strings
12-bay, single-phase, transformer-based unit Type B (& UPS model number 6 = B)
UPS
Load
Rating Level 1
Table 41
480
455
430
333
309
212
187
161
152
144
480
480
480
459
446
434
422
337
324
311
27
480
457
433
338
314
218
193
164
155
147
480
480
480
461
449
437
425
341
329
316
28
480
459
436
341
319
224
200
166
158
150
480
480
480
463
451
440
428
345
333
321
29
480
461
438
345
323
301
206
182
161
153
480
480
480
464
453
442
431
420
337
325
30
480
463
441
420
327
305
211
189
163
156
480
480
480
466
456
445
434
423
340
329
31
480
464
443
423
331
310
216
194
165
158
480
480
480
480
457
447
437
426
343
333
32
480
466
446
426
334
314
221
200
167
160
480
480
480
480
459
449
439
429
347
336
33
Specifications
Liebert® APS™
Liebert® APS™
84
24
25
26
27
28
29
30
31
32
33
-
-
-
-
-
-
-
-
-
-
-
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
71 147 203 317 342 431 443 452 459 465 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
23
35
22
-
21
20%
20
-
-
-
-
-
-
-
-
-
-
-
22
75
38
25
18
14
11
9
7
6
5
79
50
41
32
107 126 138 147 155 161 167 190 203 213 222 303 310 317 323 328 333 338 342 346 422 425 428 431 434 436
125 142 155 165 193 211 226 310 320 329 337 343 421 426 431 435 439 443 446 449 451 454 456 458 460 462 464 465
102 125 140 152 161 180 197 212 224 307 316 324 331 337 343 420 424 428 432 436 439 442 445 447 449 452 454 456
125 147 161 190 212 302 316 328 337 346 425 431 436 441 445 448 452 455 458 460 462 465 467 480 480 480 480 480 480
97
76
109 126 135 143 150 156 161 165 185 195 205 213 221 227 306 311 317 322 326 330 334 338 341 344
91
70
52
47
41
36
31
98
77
65
51
47
43
95
78
69
60
98
81
74
90
96
102 107 112 122 127 132 136 140 143 147 150 152 155 158
100 106 111 122 127 132 137 141 145 148 151 154 157 160 162 164
105 110 122 128 134 139 143 147 151 154 157 160 163 165 167 186 192
93
79
103 110 123 129 135 141 145 150 154 157 160 163 166 183 190 196 202 208 213
90
75
67
101 109 123 131 137 143 148 153 157 161 164 167 187 195 202 208 214 220 225 302 307
81
71
61
51
108 122 132 139 146 152 157 161 165 182 192 200 208 215 222 300 305 310 315 319 324 327
91
74
63
51
47
105 121 132 141 149 155 161 165 186 197 206 215 223 302 308 314 320 325 329 333 337 341 344 420
81
67
51
47
42
38
-
-
-
-
-
-
-
-
-
100 120 134 144 153 160 166 191 204 215 225 305 313 320 326 332 337 341 346 421 425 428 432 434 437 440
73
52
46
40
34
28
26
124 151 167 211 306 323 336 347 428 435 441 447 451 455 459 462 465 467 480 480 480 480 480 480 480 480 480 480 480
77
52
46
38
31
26
22
20
-
91
53
44
36
27
23
19
17
15
112 137 150 161 182 201 217 302 313 322 330 337 343 421 426 430 434 438 442 445 447 450 452 455 457 459 461
61
42
30
25
19
16
13
11
10
130 155 188 219 313 329 342 424 432 439 445 450 454 458 462 465 467 480 480 480 480 480 480 480 480 480 480 480 480 480
91
66
50
19
105 126 139 149 157 164 186 200 213 223 304 313 320 326 332 338 342 347 423 426 430 433 436 439 441 444 446
92
18
30%
16
13
71
81
17
-
50
63
16
108 126 137 145 152 158 164 182 193 204 213 222 301 308 314 320 325 330 334 338 342 345 421 424 426
98
15
-
39
44
96
80
14
40%
22
26
76
67
13
50%
8
10
61
50
12
-
46
41
11
100 110 126 134 142 148 154 159 163 167 187 197 205 213 219 226 304 309 314 319 323 327 331 334
10
-
33
27
9
83
60%
19
16
8
72
70%
7
5
7
53
-
6
47
-
5
37
80%
4
25
90%
3
5
-
100%
14
2
Load
Level 1
# Battery Strings
12-bay, single-phase, transformer-based unit Type F (& UPS model number 6 = F)
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
10 kVA /
9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 42
Specifications
85
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
67
44
32
25
20
16
13
11
10
76
53
47
41
35
28
26
79
66
52
47
43
83
72
62
51
92
76
68
91
97 103 108 112 123 128 133 137 140 144 147 150 153 156 158 160 163 165 166
95 101 107 112 123 129 134 138 142 146 149 152 155 158 161 163 165 167 185 190 195
80
99 106 112 124 130 135 140 144 148 152 155 158 161 164 166 182 189 194 200 205 210 215
82
74
97 105 112 125 131 137 142 147 151 155 159 162 165 167 186 193 200 206 211 216 221 226 302 306
79
70
61
94 103 111 125 133 139 145 150 155 159 162 166 183 191 199 206 212 218 223 301 305 310 314 318 322 325
75
64
51
48
83 100 110 126 134 142 148 154 159 163 167 187 197 205 213 219 226 304 309 314 319 323 327 331 334 338 341 344
69
52
47
43
38
95 108 125 136 145 152 158 163 180 192 203 212 221 300 307 313 319 324 329 333 337 341 345 420 423 426 429 431 434
72
53
47
42
37
31
81 104 125 138 149 157 164 185 199 212 222 304 312 319 326 332 337 342 346 422 426 429 433 436 438 441 443 446 448 450 452
60
47
39
32
27
23
20
98 126 143 156 165 195 213 227 311 321 330 338 344 422 427 432 436 440 443 447 449 452 454 457 459 461 463 464 466 467 480 480
62
46
37
28
23
20
17
15
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
60
40
27
21
17
14
11
9
8
64
46
37
28
23
20
17
15
77
52
44
36
28
25
21
18
76
53
47
41
35
28
26
76
61
49
44
39
34
83
69
52
47
43
38
81
70
53
49
45
80
70
53
50
91
75
65
52
83
74
66
82
74
92
78
91
95
99 103 106 109 112 121 125 128 131
97 101 105 109 112 121 125 129 132 135 138 141
81
95 100 104 108 112 122 126 130 134 137 140 143 146 148 151
78
70
97 103 107 112 122 127 131 135 139 142 146 149 151 154 156 159 161
79
70
61
94 100 106 111 122 128 133 137 141 145 149 152 155 157 160 162 165 167 183 188
75
64
51
48
97 104 110 122 129 134 139 144 148 152 155 159 162 164 167 184 191 197 202 208 213 217
76
63
50
46
42
91 100 108 122 130 137 142 148 152 157 160 164 167 186 193 201 207 213 219 224 301 306 310 314 318
68
51
45
40
34
28
94 106 122 132 140 147 153 158 163 167 188 198 207 214 222 300 306 312 317 321 326 330 334 337 340 344 347
66
49
42
35
28
25
22
79 102 122 136 147 155 162 181 195 208 219 300 309 316 323 329 334 339 344 420 424 427 431 434 437 439 442 444 446 448
49
38
28
23
18
16
13
11
-
-
-
-
-
-
-
-
-
-
52
37
26
20
16
12
10
9
7
71
45
33
25
20
16
13
11
10
65
46
37
28
23
20
17
15
75
51
43
35
27
23
20
18
83
61
47
40
32
27
23
20
77
53
47
41
35
28
26
83
67
50
44
38
32
27
78
64
50
45
40
34
83
69
52
47
42
38
79
66
52
47
43
83
71
53
49
45
94
75
64
51
47
83
72
62
51
93
76
66
52
82
73
64
92
76
67
96
79
70
91
76
94
79
90
93
96
97 101 104 106
81
99 103 106 109 112 120 124
82
74
97 101 105 108 112 121 125 128 131 134 137
79
69
60
99 104 108 111 121 126 130 133 137 140 143 145 148 151
79
68
53
49
95 101 106 111 121 126 131 135 139 143 146 149 152 154 157 159 161 163
75
61
50
45
40
97 103 109 121 127 132 137 142 146 150 153 156 159 162 164 167 183 189 195 200 205
73
53
47
42
36
31
98 107 120 128 135 141 146 151 155 159 162 165 182 190 197 204 210 216 221 226 303 307 311 315
70
50
44
37
30
26
22
83 102 113 130 139 147 153 159 164 181 192 202 211 219 227 305 311 317 322 326 331 335 339 342 345 420 423 426
51
41
30
25
20
17
14
12
96 123 141 154 164 190 209 223 308 318 327 335 342 420 425 430 434 438 441 445 448 450 453 455 457 459 461 463 465 466 480
43
27
19
14
11
9
7
6
5
96 130 151 164 198 220 309 322 333 342 422 429 435 440 444 448 452 455 458 460 463 465 467 480 480 480 480 480 480 480 480 480
43
27
19
14
11
9
7
6
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
83 135 159 197 226 319 335 347 428 436 443 449 453 457 461 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
41
26
19
14
11
9
7
6
5
73 104 132 149 160 185 206 222 308 319 329 337 344 422 428 433 437 441 444 448 451 453 456 458 460 462 464 466 467 480 480 480 480
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
-
-
90%
-
-
100%
10%
81 157 222 331 426 441 451 459 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
10%
20%
40 94 140 163 206 306 326 340 424 433 440 447 452 457 460 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
20%
-
25 53 100 134 154 167 205 226 314 327 337 346 426 432 438 443 447 451 454 457 460 462 465 467 480 480 480 480 480 480 480 480 480 480 480
30%
91 109 130 143 153 160 167 194 208 219 301 310 318 325 331 337 342 347 423 427 430 434 437 439 442 444 447 449 451 453 455
80 107 131 145 156 164 190 207 221 304 314 323 330 337 343 420 425 429 433 437 440 443 446 448 451 453 455 457 459 461 462 464
67
98 110 128 139 147 154 160 165 186 197 208 217 225 304 311 317 322 327 332 336 340 344 347 423 426 428 431 434 436
95 110 129 141 150 157 163 183 196 208 218 227 307 314 321 327 332 337 341 345 421 425 428 431 434 436 439 441 443 445
78
Tables for UPS Model Number Where Digits 1-3 are AS4 or ASD
-
18 44
40%
52
46
74
63
7.4.1
30%
14 35
50%
51
47
Estimated Battery Run Times
40%
11 27
60%
40
34
90 102 111 127 136 143 149 155 160 164 180 190 199 207 215 222 300 306 311 316 320 325 329 332 336 339 342 345
81 100 111 128 137 145 152 157 162 167 188 198 208 216 223 302 308 314 319 324 328 332 336 340 343 346 421 424 426
74
7.4
20 kVA /
18 kW
15 kVA /
13.5 kW
10 kVA /
9 kW
5 kVA /
4.5 kW
23
19
69
60
# Battery Strings
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
9
51
47
9
7
42
38
8
70%
28
26
7
80%
17
15
6
6
5
5
4
90%
3
100%
2
16-bay, single-phase, transformer-based unit Type N (& UPS model number 6 = N)
UPS
Load
Rating Level 1
Table 43
Specifications
Liebert® APS™
Liebert® APS™
86
14
15
17
18
19
20
# Battery Strings
16
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
109 126 135 143 150 156 161 165 185 195 204 213 220 227 305 311 317 321 326 330 334 338 341 344 347 422 425
22
34
70 146 201 315 341 430 442 451 459 464 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
75
38
25
18
14
11
9
7
6
5
79
50
41
32
124 142 155 165 193 211 226 310 320 329 336 343 421 426 431 435 439 443 446 449 451 454 456 458 460 462 464 465 467 480 480
102 125 140 152 160 180 197 212 224 306 316 324 331 337 342 420 424 428 432 436 439 442 444 447 449 452 454 456 457 459 461
125 146 160 189 212 301 316 327 337 345 424 430 436 440 444 448 452 455 457 460 462 464 466 480 480 480 480 480 480 480 480 480
97
76
91
53
44
36
27
23
19
17
15
91
70
52
47
41
36
31
98
77
65
51
47
43
95
78
69
60
98
81
74
90
96
102 107 112 122 127 132 136 140 143 147 150 152 155 158 160 162 164
100 106 111 122 127 132 137 141 145 148 151 154 157 160 162 164 166 182 188
104 110 122 128 134 138 143 147 151 154 157 160 163 165 167 185 191 197 202 207
93
79
103 110 122 129 135 141 145 150 154 157 160 163 166 183 190 196 202 208 213 218 223 227
90
75
67
101 109 123 131 137 143 148 153 157 161 164 167 187 195 202 208 214 220 225 302 307 311 315 319
81
71
61
51
108 123 132 139 146 152 157 161 165 182 192 200 208 215 222 300 305 310 315 320 324 328 331 335 338
92
74
62
51
47
105 121 132 141 149 155 161 165 186 197 206 215 223 302 308 314 320 325 329 333 337 341 344 420 423 425 428
81
67
51
47
42
38
100 120 134 144 153 160 166 191 204 215 225 305 313 320 326 332 337 341 346 422 425 428 432 434 437 440 442 444 446
73
52
46
40
34
28
26
112 137 150 161 182 201 217 302 312 322 330 337 343 421 426 430 434 438 441 445 447 450 452 455 457 459 461 462 464 465
77
52
46
38
31
26
22
20
-
-
-
-
-
-
-
-
-
-
82
41
26
18
14
11
9
7
6
5
75
48
37
27
22
18
16
13
11
97
61
45
36
28
23
20
17
15
91
65
49
42
35
28
25
22
83
67
51
45
39
34
28
99
75
60
49
43
38
33
95
75
62
50
46
41
93
74
63
51
47
99
79
69
53
50
96
78
69
60
93
78
70
98
81
74
96
81
90
94
98
102 105 109 112 121 124 127 130
100 104 108 111 120 124 128 131 134 137 140
103 107 111 121 125 129 132 136 139 142 145 147 150
91
77
101 106 111 121 126 130 134 138 141 145 148 150 153 155 158 160
82
74
65
105 110 121 127 132 136 140 144 148 151 154 157 159 162 164 166 181 186
90
74
64
52
103 109 121 127 133 138 143 147 151 155 158 161 163 166 182 188 195 200 206 211 215
81
69
52
48
45
107 120 128 135 141 146 151 155 159 162 166 182 190 197 204 210 216 221 226 303 308 312 316
82
68
52
47
42
38
103 113 129 137 144 151 156 161 165 183 193 202 210 217 224 302 308 313 318 322 326 330 334 337 341 344
75
53
47
40
34
28
26
111 131 142 151 158 164 186 199 211 221 302 309 317 323 329 334 339 343 347 423 426 429 432 435 438 440 442 445
75
51
43
36
28
25
21
18
90
42
26
19
14
11
9
7
6
5
68
44
32
25
20
16
13
11
10
80
50
40
30
25
20
17
14
12
99
62
46
37
28
23
20
17
15
81
60
46
39
32
26
23
20
96
68
50
43
36
30
26
22
82
65
50
44
38
32
27
95
72
52
47
42
36
31
82
69
52
47
42
38
94
74
60
49
45
40
82
70
53
49
45
93
75
63
51
47
98
78
68
53
49
92
75
65
52
96
79
69
60
91
76
67
95
79
70
99
81
73
94
79
97
81
90
93
100 103
102 105 108 111 120
90
76
100 104 108 111 120 124 127 130 133
82
72
64
103 107 111 120 124 128 132 136 139 142 145 147
82
72
61
51
100 105 110 120 125 130 134 138 141 145 148 151 153 156 158 160
78
66
51
47
43
102 108 113 125 131 136 140 144 148 152 155 158 161 163 165 180 186 192 197
77
63
50
44
39
34
104 111 125 132 138 144 149 153 157 161 164 167 185 193 199 206 212 217 222 227 304 308
76
53
47
41
34
28
26
110 126 136 144 150 156 161 166 186 196 205 213 221 300 306 312 317 322 326 331 334 338 342 345 420
73
50
42
34
27
23
20
18
111 136 149 160 180 199 215 300 311 320 328 336 342 420 425 429 433 437 440 444 446 449 452 454 456 458 460 462 463
50
36
26
19
16
12
10
9
7
-
-
-
-
-
-
-
-
-
-
121 143 158 182 206 224 311 323 333 341 421 427 433 437 442 446 449 452 455 458 460 462 464 466 480 480 480 480 480 480 480
52
38
27
21
17
13
11
9
8
124 151 167 210 305 322 336 347 427 435 441 446 451 455 458 462 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480
61
42
30
25
19
16
13
11
10
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
129 155 187 218 312 328 341 423 432 439 445 450 454 458 461 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
91
66
50
107 126 137 147 155 161 166 190 202 213 222 302 310 317 323 328 333 338 342 346 421 425 428 431 434 436 439 441 443
105 125 139 149 157 164 186 200 212 223 304 312 320 326 332 337 342 347 423 426 430 433 436 439 441 444 446 448 450 452
92
13
108 126 136 145 152 158 164 181 193 204 213 221 301 308 314 319 325 329 334 338 342 345 420 423 426 429 432 434
98
12
16
81
71
96
80
11
100 110 125 134 142 148 154 159 163 167 187 196 205 212 219 226 303 309 314 318 323 327 331 334 337 341 343
10
13
63
50
76
67
83
9
40%
44
38
60
50
72
8
50%
26
22
46
41
53
7
8
33
27
47
6
10
19
16
37
5
60%
7
80%
25
4
70%
5
90%
14
3
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
20 kVA /
18 kW
15 kVA /
13.5 kW
10 kVA /
9 kW
5 kVA /
4.5 kW
5
100%
2
16-bay, single-phase, transformer-based unit Type R (& UPS model number 6 = R)
UPS
Load
Rating Level 1
Table 44
Specifications
87
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
83
41
26
19
14
11
9
7
6
5
110 128 139 147 154 160 165 186 197 208 217 225 304 311 317 322 327 332 336 340 344 347 423 426 428 431 434
109 130 143 153 160 167 194 208 219 301 310 318 325 331 337 342 347 423 427 430 434 437 439 442 444 447 449 451 453
110 129 141 150 157 163 183 196 208 218 227 307 314 321 327 332 337 341 345 421 425 428 431 434 436 439 441 443
107 131 145 156 164 190 207 221 304 314 323 330 337 343 420 425 429 433 437 440 443 446 448 451 453 455 457 459 461 462
91
95
100 111 128 137 145 152 157 162 167 188 198 208 216 223 302 308 314 319 324 328 332 336 340 343 346 421 424
104 132 149 160 185 206 222 308 319 329 337 344 422 428 433 437 441 444 448 451 453 456 458 460 462 464 466 467 480 480 480
80
67
74
98
81
98
62
46
37
28
23
20
17
15
95
72
53
47
42
37
31
94
75
64
51
48
97
79
70
61
99
82
74
91
97
103 108 112 123 128 133 137 140 144 147 150 153 156 158 160 163 165
101 107 112 123 129 134 138 142 146 149 152 155 158 161 163 165 167 185 190
106 112 124 130 135 140 144 148 152 155 158 161 164 166 182 189 194 200 205 210
95
80
105 112 125 131 137 142 147 151 155 159 162 165 167 186 193 200 206 211 216 221 226 302
92
76
68
103 111 125 133 139 145 150 155 159 162 166 183 191 199 206 212 218 223 301 305 310 314 318 322
83
72
62
51
100 110 126 134 142 148 154 159 163 167 187 197 205 213 219 226 304 309 314 319 323 327 331 334 338 341
79
66
52
47
43
108 125 136 145 152 158 163 180 192 203 212 221 300 307 313 319 324 329 333 337 341 345 420 423 426 429 431
83
69
52
47
43
38
104 125 138 149 157 164 185 199 212 222 304 312 319 326 332 337 342 346 422 426 429 433 436 438 441 443 446 448 450
76
53
47
41
35
28
26
126 143 156 165 195 213 227 311 321 330 338 344 422 427 432 436 440 443 447 449 452 454 457 459 461 463 464 466 467 480
81
60
47
39
32
27
23
20
-
-
-
-
-
-
-
-
-
-
96
43
27
19
14
11
9
7
6
5
79
49
38
28
23
18
16
13
11
77
52
44
36
28
25
21
18
94
66
49
42
35
28
25
22
91
68
51
45
40
34
28
83
69
52
47
43
38
97
76
63
50
46
42
94
75
64
51
48
91
75
65
52
97
79
70
61
95
78
70
92
78
97
81
91
95
99
103 106 109 112 121 125 128
101 105 109 112 121 125 129 132 135 138
100 104 108 112 122 126 130 134 137 140 143 146 148
82
74
103 107 112 122 127 131 135 139 142 146 149 151 154 156 159
83
74
66
100 106 111 122 128 133 137 141 145 149 152 155 157 160 162 165 167 183
80
70
53
50
104 110 122 129 134 139 144 148 152 155 159 162 164 167 184 191 197 202 208 213
81
70
53
49
45
100 108 122 130 137 142 148 152 157 160 164 167 186 193 201 207 213 219 224 301 306 310 314
76
61
49
44
39
34
106 122 132 140 147 153 158 163 167 188 198 207 214 222 300 306 312 317 321 326 330 334 337 340 344
76
53
47
41
35
28
26
102 122 136 147 155 162 181 195 208 219 300 309 316 323 329 334 339 344 420 424 427 431 434 437 439 442 444 446
64
46
37
28
23
20
17
15
96
43
27
19
14
11
9
7
6
5
71
45
33
25
20
16
13
11
10
83
51
41
30
25
20
17
14
12
75
51
43
35
27
23
20
18
83
61
47
40
32
27
23
20
98
70
50
44
37
30
26
22
83
67
50
44
38
32
27
97
73
53
47
42
36
31
83
69
52
47
42
38
95
75
61
50
45
40
83
71
53
49
45
94
75
64
51
47
99
79
68
53
49
93
76
66
52
97
79
69
60
92
76
67
96
79
70
99
82
74
94
79
97
81
90
93
101 104
103 106 109 112 120
91
76
101 105 108 112 121 125 128 131 134
82
73
64
104 108 111 121 126 130 133 137 140 143 145 148
83
72
62
51
101 106 111 121 126 131 135 139 143 146 149 152 154 157 159 161
79
66
52
47
43
103 109 121 127 132 137 142 146 150 153 156 159 162 164 167 183 189 195 200
78
64
50
45
40
34
107 120 128 135 141 146 151 155 159 162 165 182 190 197 204 210 216 221 226 303 307 311
77
53
47
41
35
28
26
102 113 130 139 147 153 159 164 181 192 202 211 219 227 305 311 317 322 326 331 335 339 342 345 420 423
65
46
37
28
23
20
17
15
123 141 154 164 190 209 223 308 318 327 335 342 420 425 430 434 438 441 445 448 450 453 455 457 459 461 463 465 466
52
37
26
20
16
12
10
9
7
130 151 164 198 220 309 322 333 342 422 429 435 440 444 448 452 455 458 460 463 465 467 480 480 480 480 480 480 480 480
60
40
27
21
17
14
11
9
8
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
135 159 197 226 319 335 347 428 436 443 449 453 457 461 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
67
44
32
25
20
16
13
11
10
140 163 206 306 326 340 424 433 440 447 452 457 460 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
100 134 154 167 205 226 314 327 337 346 426 432 438 443 447 451 454 457 460 462 465 467 480 480 480 480 480 480 480 480 480 480
73
52
46
51
78
69
-
-
-
-
-
94
53
44
35
27
40
63
51
50%
34 35
60%
33
-
32
-
31
70%
30
80%
29
-
28
-
27
90%
26
100%
25
- 81 157 222 331 426 441 451 459 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
24
- 40
23
10%
22
20%
21
- 25
20
- 18
19
30%
18
40%
17
# Battery Strings
- 14
16
- 11
15
50%
14
102 111 127 136 143 149 155 160 164 180 190 199 207 215 222 300 306 311 316 320 325 329 332 336 339 342
13
60%
23
47
42
90
12
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
20 kVA /
18 kW
15 kVA /
13.5 kW
10 kVA /
9 kW
5 kVA /
4.5 kW
9
34
28
74
11
-
19
17
60
10
70%
7
6
47
9
-
38
8
-
26
7
80%
15
6
90%
5
5
-
4
100%
3
16-bay, single-phase, transformer-based unit Type B (& UPS model number 6 = B)
UPS
Load
Rating Level 1 2
Table 45
Specifications
Liebert® APS™
Liebert® APS™
88
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
75
38
25
18
14
11
92
107 126 137 147 155 161 166 190 202 213 222 302 310 317 323 328 333 338 342 346 421 425 428 431 434 436 439 441
124 142 155 165 193 211 226 310 320 329 336 343 421 426 431 435 439 443 446 449 451 454 456 458 460 462 464 465 467 480
102 125 140 152 160 180 197 212 224 306 316 324 331 337 342 420 424 428 432 436 439 442 444 447 449 452 454 456 457 459
105 125 139 149 157 164 186 200 212 223 304 312 320 326 332 337 342 347 423 426 430 433 436 439 441 444 446 448 450
125 146 160 189 212 301 316 327 337 345 424 430 436 440 444 448 452 455 457 460 462 464 466 480 480 480 480 480 480 480 480
97
76
71
81
91
53
44
36
27
23
19
17
15
91
70
52
47
41
36
31
98
77
65
51
47
43
95
78
69
60
98
81
74
90
96
102 107 112 122 127 132 136 140 143 147 150 152 155 158 160 162
100 106 111 122 127 132 137 141 145 148 151 154 157 160 162 164 166 182
104 110 122 128 134 138 143 147 151 154 157 160 163 165 167 185 191 197 202
93
79
103 110 122 129 135 141 145 150 154 157 160 163 166 183 190 196 202 208 213 218 223
90
75
67
101 109 123 131 137 143 148 153 157 161 164 167 187 195 202 208 214 220 225 302 307 311 315
81
71
61
51
108 123 132 139 146 152 157 161 165 182 192 200 208 215 222 300 305 310 315 320 324 328 331 335
92
74
62
51
47
105 121 132 141 149 155 161 165 186 197 206 215 223 302 308 314 320 325 329 333 337 341 344 420 423 425
81
67
51
47
42
38
100 120 134 144 153 160 166 191 204 215 225 305 313 320 326 332 337 341 346 422 425 428 432 434 437 440 442 444
73
52
46
40
34
28
26
112 137 150 161 182 201 217 302 312 322 330 337 343 421 426 430 434 438 441 445 447 450 452 455 457 459 461 462 464
77
52
46
38
31
26
22
20
-
-
-
-
-
-
-
-
-
-
82
41
26
18
14
11
9
7
6
5
75
48
37
27
22
18
16
13
11
97
61
45
36
28
23
20
17
15
91
65
49
42
35
28
25
22
83
67
51
45
39
34
28
99
75
60
49
43
38
33
95
75
62
50
46
41
93
74
63
51
47
99
79
69
53
50
96
78
69
60
93
78
70
98
81
74
96
81
90
94
98
102 105 109 112 121 124 127
100 104 108 111 120 124 128 131 134 137
103 107 111 121 125 129 132 136 139 142 145 147
91
77
101 106 111 121 126 130 134 138 141 145 148 150 153 155 158
82
74
65
105 110 121 127 132 136 140 144 148 151 154 157 159 162 164 166 181
90
74
64
52
103 109 121 127 133 138 143 147 151 155 158 161 163 166 182 188 195 200 206 211
81
69
52
48
45
107 120 128 135 141 146 151 155 159 162 166 182 190 197 204 210 216 221 226 303 308 312
82
68
52
47
42
38
103 113 129 137 144 151 156 161 165 183 193 202 210 217 224 302 308 313 318 322 326 330 334 337 341
75
53
47
40
34
28
26
111 131 142 151 158 164 186 199 211 221 302 309 317 323 329 334 339 343 347 423 426 429 432 435 438 440 442
75
51
43
36
28
25
21
18
90
42
26
19
14
11
9
7
6
5
68
44
32
25
20
16
13
11
10
80
50
40
30
25
20
17
14
12
99
62
46
37
28
23
20
17
15
81
60
46
39
32
26
23
20
96
68
50
43
36
30
26
22
82
65
50
44
38
32
27
95
72
52
47
42
36
31
82
69
52
47
42
38
94
74
60
49
45
40
82
70
53
49
45
93
75
63
51
47
98
78
68
53
49
92
75
65
52
96
79
69
60
91
76
67
95
79
70
99
81
73
94
79
97
81
90
100
102 105 108 111
90
76
100 104 108 111 120 124 127 130
82
72
64
103 107 111 120 124 128 132 136 139 142 145
82
72
61
51
100 105 110 120 125 130 134 138 141 145 148 151 153 156 158
78
66
51
47
43
102 108 113 125 131 136 140 144 148 152 155 158 161 163 165 180 186 192
77
63
50
44
39
34
104 111 125 132 138 144 149 153 157 161 164 167 185 193 199 206 212 217 222 227 304
76
53
47
41
34
28
26
110 126 136 144 150 156 161 166 186 196 205 213 221 300 306 312 317 322 326 331 334 338 342 345
73
50
42
34
27
23
20
18
111 136 149 160 180 199 215 300 311 320 328 336 342 420 425 429 433 437 440 444 446 449 452 454 456 458 460 462
50
36
26
19
16
12
10
9
7
-
-
-
-
-
-
-
-
-
-
121 143 158 182 206 224 311 323 333 341 421 427 433 437 442 446 449 452 455 458 460 462 464 466 480 480 480 480 480 480
52
38
27
21
17
13
11
9
8
124 151 167 210 305 322 336 347 427 435 441 446 451 455 458 462 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480
61
42
30
25
19
16
13
11
10
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
129 155 187 218 312 328 341 423 432 439 445 450 454 458 461 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
91
66
50
50
63
109 126 135 143 150 156 161 165 185 195 204 213 220 227 305 311 317 321 326 330 334 338 341 344 347 422
108 126 136 145 152 158 164 181 193 204 213 221 301 308 314 319 325 329 334 338 342 345 420 423 426 429 432
98
40%
-
-
9
7
6
5
79
50
41
32
38
44
96
80
-
22
26
76
67
-
-
-
-
-
8
60
50
50%
34 35
60%
33
-
32
-
31
70%
30
80%
29
-
28
-
27
90%
26
100%
25
- 70 146 201 315 341 430 442 451 459 464 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
24
- 34
23
10%
22
20%
21
- 22
20
30%
19
- 16
18
- 13
17
# Battery Strings
40%
16
50%
15
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
20 kVA /
18 kW
15 kVA /
13.5 kW
10 kVA /
9 kW
5 kVA /
4.5 kW
14
100 110 125 134 142 148 154 159 163 167 187 196 205 212 219 226 303 309 314 318 323 327 331 334 337 341
13
- 10
46
41
83
12
-
33
27
72
11
60%
19
16
53
10
70%
7
5
47
9
-
37
8
-
25
7
80%
14
6
90%
5
5
-
4
100%
3
16-bay, single-phase, transformer-based unit Type F (& UPS model number 6 = F)
UPS
Load
Rating Level 1 2
Table 46
Specifications
24
25
26
27
28
29
30
31
32
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
79
111 139 155 166 199 218 305 318 328 337 345 423 429 434 439 443 446 450 453 455 458 460 462 464 466 480 480 480 480
109 143 161 195 220 311 326 337 347 427 434 440 445 449 453 457 460 462 465 467 480 480 480 480 480 480 480 480 480 480
89
76
47
35
26
21
17
14
11
10
94
65
48
41
33
27
23
21
92
72
53
48
43
39
97
77
66
52
48
94
78
69
96
81
93
99
104 109 120 125 130 134 138 142 145 149 152 154 157 159 162
103 108 113 125 130 135 140 144 147 151 154 157 159 162 164 166 182
101 108 113 126 132 137 142 146 150 153 157 160 162 165 167 186 192 198 203
83
76
100 107 120 127 134 139 144 149 153 157 160 163 166 183 191 197 204 209 215 220 225
81
71
62
106 120 128 136 142 148 153 157 161 164 180 189 197 204 211 217 222 300 305 309 314 318
91
74
64
52
104 113 130 138 145 151 157 161 166 185 195 203 211 219 225 303 309 314 319 323 328 331 335 338
81
68
52
48
44
101 113 131 141 149 156 162 167 191 202 212 221 301 308 314 320 326 330 335 339 343 347 422 425 428 431
75
60
48
43
37
32
111 133 145 155 162 183 199 212 223 305 314 322 328 334 340 345 421 425 429 433 436 439 441 444 446 449 451
80
62
48
42
36
28
26
108 136 152 164 193 213 301 314 325 334 342 420 426 432 436 440 444 448 451 453 456 458 461 463 465 466 480 480 480
69
48
39
30
25
20
18
16
-
-
-
-
-
-
67
43
28
22
18
14
12
92
51
40
30
23
19
16
14
11
82
53
46
38
30
26
21
18
22
26
80
62
48
42
36
28
28
96
72
52
46
41
35
35
39
93
72
53
48
43
42
45
90
72
60
49
48
97
77
66
52
50
53
94
77
67
62
67
92
76
71
97
80
75
79
94
99
82
92
97
101 104 107 111 113 123
103 107 110 113 123 127 131 134
102 106 110 120 124 128 132 136 139 142 145
83
100 105 110 120 125 130 134 138 141 145 148 151 153 156
81
71
104 109 120 126 131 136 140 144 148 151 154 157 160 162 165 167
82
72
61
101 108 120 127 133 138 143 148 152 155 159 162 165 167 185 192 198 204 209
78
65
51
47
105 113 128 135 141 147 152 156 160 164 167 187 195 203 209 216 221 227 304 308 313
79
64
50
45
40
101 112 129 138 146 152 158 163 167 190 200 209 217 224 303 309 315 320 325 329 333 337 341 344
71
51
44
37
30
26
109 131 143 153 161 167 195 209 220 302 311 319 326 332 338 343 347 423 427 431 434 437 440 443 445 447
70
48
39
30
25
21
18
15
106 140 158 188 214 306 321 333 343 424 431 437 442 447 451 454 458 460 463 465 480 480 480 480 480 480 480 480 480
46
28
20
16
12
8
10
-
-
-
-
-
-
-
-
-
-
Tables for UPS Model Number Where Digits 1-3 are AS5 or ASE
9
8
6
5
7.5.1
-
-
-
-
104 148 184 222 319 336 422 432 441 447 453 458 462 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
46
28
20
15
12
9
7
6
5
106 150 188 225 321 339 424 434 442 449 454 459 463 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
67
47
112 137 150 161 182 201 217 302 313 322 330 337 343 421 426 430 434 438 442 445 447 450 452 455 457 459 461 462
113 135 147 156 164 187 203 216 227 308 317 324 331 337 342 347 423 427 431 434 438 440 443 446 448 450 452
113 133 144 153 160 166 190 203 214 224 305 312 319 325 331 336 341 345 421 425 428 431 434 437 439 442
101 113 132 142 150 157 162 167 192 203 213 222 301 309 315 321 326 331 336 340 344 347 422 426 428 431
Estimated Battery Run Times
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
-
100%
45
23
101 167 314 347 438 451 460 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
22
10%
21
20%
20
27
19
20
91
96
18
30%
61
71
99
81
17
40%
38
48
77
66
16
15
28
53
48
15
50%
# Battery Strings
104 113 129 138 145 151 157 161 165 184 194 203 211 218 225 303 309 314 319 323 327 331 335 338
14
103 113 130 139 147 154 159 164 182 193 203 212 220 227 305 311 317 322 327 331 335 339 342 346 421
92
13
11
42
36
83
75
12
60%
25
20
71
62
11
9
52
48
10
7
43
39
9
70%
28
26
8
80%
18
15
7
6
6
5
5
90%
4
100%
3
1
Load
Level
2
10-bay, two-phase, no transformer unit Type N (& UPS model number 6 = N)
7.5
15 kVA /
13.5 kW
10 kVA /
9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 47
Specifications
Liebert® APS™
Liebert® APS™
90
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
32
80%
31
-
30
-
29
90%
28
100%
27
91 160 301 337 430 444 455 462 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
26
42
25
10%
24
20%
23
26
22
19
21
30%
20
40%
19
14
112 132 143 152 159 165 188 201 212 222 303 311 318 324 330 335 340 344 420 424 427 430 433 436 438 441
111 133 145 155 163 183 199 212 224 306 314 322 329 335 340 345 421 426 429 433 436 439 442 444 447 449 451
110 134 148 159 167 196 212 226 309 318 327 334 340 346 423 428 432 436 439 443 445 448 451 453 455 457 459 461
94
100 113 131 141 149 156 162 167 190 202 212 221 301 308 314 320 325 330 335 339 343 346 422 425 428 431
108 136 152 163 192 212 300 313 324 333 341 420 426 431 436 440 444 447 450 453 456 458 460 462 464 466 480 480 480
83
69
98
80
73
46
34
26
20
17
14
12
10
91
63
48
40
33
27
23
21
98
74
53
48
43
38
32
96
77
66
52
48
94
78
70
97
81
93
99
105 109 120 125 130 135 139 142 146 149 152 155 157 160
103 109 120 126 131 136 140 144 148 151 154 157 160 162 165 167
102 108 120 126 132 137 142 146 150 154 157 160 163 165 180 187 193 199
90
76
100 107 120 127 134 139 144 149 153 157 160 163 166 183 191 197 204 209 215 220
81
72
63
105 113 128 135 141 147 152 156 160 164 167 187 195 203 209 216 221 227 304 308 313
91
74
64
52
103 112 128 137 144 150 156 160 165 182 192 201 209 216 223 301 307 312 317 322 326 330 333
80
68
52
48
44
111 129 139 147 154 160 165 186 198 208 217 225 305 311 317 323 328 332 337 341 344 420 423 426
91
71
53
48
44
39
109 130 143 152 160 167 194 207 219 301 310 318 325 331 337 342 346 423 427 430 433 436 439 442 444 447
78
61
48
42
36
30
26
105 133 149 161 187 207 224 309 320 330 338 345 423 429 433 438 442 445 448 451 454 456 459 461 463 465 466 480
67
47
38
28
25
21
18
16
-
-
-
-
-
-
-
-
-
-
8
65
42
28
22
18
14
12
10
11
83
50
40
28
23
19
16
14
15
18
80
53
45
38
30
26
22
22
99
70
50
44
37
30
26
26
28
95
71
52
46
41
35
35
39
92
72
53
48
44
42
45
90
72
60
50
48
97
77
66
52
50
53
94
77
67
62
67
92
76
71
97
80
75
79
94
82
99
92
97
100 104 107 111 113 123
103 107 110 120 124 127 131 134
102 106 110 120 124 128 132 136 139 142 145
90
100 105 110 120 125 130 134 138 141 145 148 151 153 156
81
72
103 109 120 126 131 136 140 144 148 151 154 157 160 162 164 167
82
72
61
100 107 113 126 132 138 143 147 151 155 158 161 164 167 184 191 197 203 208
78
65
51
47
104 112 126 134 140 146 151 155 159 163 166 185 193 200 207 214 219 225 302 307 311
79
64
50
45
40
110 126 136 144 151 156 161 166 186 196 205 214 221 300 306 312 317 322 327 331 335 338 342
79
62
48
42
36
30
107 128 141 151 159 165 190 204 216 226 307 315 322 329 334 340 344 421 425 428 432 435 438 440 443 445
68
47
39
30
25
21
18
102 136 155 180 207 300 316 329 339 420 427 433 439 444 448 452 455 458 461 463 466 480 480 480 480 480 480 480 480
45
28
20
15
12
9
8
6
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
144 166 214 312 331 345 428 437 444 450 455 459 463 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
104 138 157 185 212 304 319 332 342 422 429 436 441 446 450 453 457 460 462 465 467 480 480 480 480 480 480 480 480 480
76
53
47
76
65
100 145 167 216 314 333 346 429 438 445 451 456 460 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
44
27
20
15
11
9
8
6
5
99
62
46
37
28
52
48
18
104 120 130 138 145 152 157 162 166 185 195 204 212 219 226 304 309 314 319 324 328 332 335 339
17
102 113 130 139 147 154 159 164 181 193 203 211 219 227 305 311 317 322 327 331 335 339 342 345 420
93
16
50%
# Battery Strings
15
11
41
35
83
76
14
60%
25
20
71
62
13
9
52
48
12
7
43
39
11
70%
28
26
10
80%
18
9
16
8
6
7
5
6
90%
5
100%
4
2
Load
Level 1
3
10-bay, two-phase, no transformer unit Type R (& UPS model number 6 = R)
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
15 kVA /
13.5 kW
10 kVA/
9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 48
Specifications
91
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
104 113 129 138 145 151 157 161 165 184 194 203 211 218 225 303 309 314 319 323 327 331 335
103 113 130 139 147 154 159 164 182 193 203 212 220 227 305 311 317 322 327 331 335 339 342 346
92
113 133 144 153 160 166 190 203 214 224 305 312 319 325 331 336 341 345 421 425 428 431 434 437 439
101 113 132 142 150 157 162 167 192 203 213 222 301 309 315 321 326 331 336 340 344 347 422 426 428
83
75
113 135 147 156 164 187 203 216 227 308 317 324 331 337 342 347 423 427 431 434 438 440 443 446 448 450
99
81
71
62
112 137 150 161 182 201 217 302 313 322 330 337 343 421 426 430 434 438 442 445 447 450 452 455 457 459 461
96
77
66
52
48
111 139 155 166 199 218 305 318 328 337 345 423 429 434 439 443 446 450 453 455 458 460 462 464 466 480 480 480
91
71
53
48
43
39
109 143 161 195 220 311 326 337 347 427 434 440 445 449 453 457 460 462 465 467 480 480 480 480 480 480 480 480 480
79
61
48
42
36
28
26
106 150 188 225 321 339 424 434 442 449 454 459 463 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
67
47
38
28
25
20
18
15
-
-
-
-
-
-
-
-
-
-
76
47
35
26
21
17
14
11
10
94
65
48
41
33
27
23
21
92
72
53
48
43
39
97
77
66
52
48
94
78
69
96
81
93
99
104 109 120 125 130 134 138 142 145 149 152 154 157 159
103 108 113 125 130 135 140 144 147 151 154 157 159 162 164 166
101 108 113 126 132 137 142 146 150 153 157 160 162 165 167 186 192 198
83
76
100 107 120 127 134 139 144 149 153 157 160 163 166 183 191 197 204 209 215 220
81
71
62
106 120 128 136 142 148 153 157 161 164 180 189 197 204 211 217 222 300 305 309 314
91
74
64
52
104 113 130 138 145 151 157 161 166 185 195 203 211 219 225 303 309 314 319 323 328 331 335
81
68
52
48
44
101 113 131 141 149 156 162 167 191 202 212 221 301 308 314 320 326 330 335 339 343 347 422 425 428
75
60
48
43
37
32
111 133 145 155 162 183 199 212 223 305 314 322 328 334 340 345 421 425 429 433 436 439 441 444 446 449
80
62
48
42
36
28
26
108 136 152 164 193 213 301 314 325 334 342 420 426 432 436 440 444 448 451 453 456 458 461 463 465 466 480 480
69
48
39
30
25
20
18
16
104 148 184 222 319 336 422 432 441 447 453 458 462 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
46
28
20
15
12
9
7
6
5
101 167 314 347 438 451 460 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
45
27
20
15
11
9
7
6
5
2
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
10 kVA /
9 kW
5 kVA /
4.5 kW
-
100%
# Battery Strings
10-bay, two-phase, no transformer unit Type B (& UPS model number 6 = B)
UPS
Load
Rating Level 1
Table 49
Specifications
Liebert® APS™
Liebert® APS™
92
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
91
42
26
19
14
11
9
7
6
2
Load
Level 1
100
44
27
20
15
11
9
8
6
5
160
99
62
46
37
28
25
20
18
16
3
145
73
46
34
26
20
17
14
12
10
301
144
104
76
53
47
41
35
28
26
4
167
105
67
47
38
28
25
21
18
16
337
166
138
108
83
69
52
48
43
39
5
216
133
91
63
48
40
33
27
23
21
430
214
157
136
110
94
76
65
52
48
6
314
149
109
78
61
48
42
36
30
26
444
312
185
152
134
111
98
80
71
62
7
333
161
130
98
74
53
48
43
38
32
455
331
212
163
148
133
112
100
83
76
8
346
187
143
111
91
71
53
48
44
39
462
345
304
192
159
145
132
113
102
93
9
429
207
152
129
103
80
68
52
48
44
480
428
319
212
167
155
143
131
113
104
10
438
224
160
139
112
96
77
66
52
48
480
437
332
300
196
163
152
141
130
120
11
445
309
167
147
128
105
91
74
64
52
480
444
342
313
212
183
159
149
139
130
12
451
320
194
154
137
113
100
81
72
63
480
450
422
324
226
199
165
156
147
138
13
456
330
207
160
144
128
107
94
78
70
480
455
429
333
309
212
188
162
154
145
14
460
338
219
165
150
135
120
102
90
76
480
459
436
341
318
224
201
167
159
152
15
464
345
301
186
156
141
127
108
97
81
480
463
441
420
327
306
212
190
164
157
16
467
423
310
198
160
147
134
120
103
93
480
466
446
426
334
314
222
202
181
162
17
480
429
318
208
165
152
139
126
109
99
480
480
450
431
340
322
303
212
193
166
18
# Battery Strings
480
433
325
217
182
156
144
132
120
105
480
480
453
436
346
329
311
221
203
185
19
10-bay, two-phase, no transformer unit Type F (& UPS model number 6 = F)
480
438
331
225
192
160
149
137
126
109
480
480
457
440
423
335
318
301
211
195
20
480
442
337
305
201
164
153
142
131
120
480
480
460
444
428
340
324
308
219
204
21
480
445
342
311
209
167
157
146
136
125
480
480
462
447
432
345
330
314
227
212
480
448
346
317
216
187
160
150
140
130
480
480
465
450
436
421
335
320
305
219
480
451
423
323
223
195
163
154
144
135
480
480
467
453
439
426
340
325
311
226
480
454
427
328
301
203
166
157
148
139
480
480
480
456
443
429
344
330
317
304
314
459
480
480
433
337
312
216
191
163
154
146
480
480
480
460
448
436
424
339
327
456
430
332
307
209
183
160
151
142
480
480
480
458
445
433
420
335
322
309
480
461
436
341
317
221
197
165
157
149
480
480
480
462
451
439
427
343
331
319
480
463
439
344
322
227
204
180
160
152
480
480
480
464
453
442
430
346
335
324
480
465
442
420
326
304
209
187
162
155
480
480
480
466
455
444
433
422
339
328
480
466
444
423
330
308
215
193
165
157
480
480
480
480
457
447
436
425
342
332
-
-
-
-
-
-
-
-
-
-
480
480
480
480
459
449
438
428
345
335
22 23 24 25 26 27 28 29 30 31 32
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
10 kVA /
9 kW
5 kVA /
4.5 kW
UPS
Rating
Table 50
Specifications
27
45
30%
20%
10
11
12
13
14
15
17
18
19
20
# Battery Strings
16
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
104 113 129 138 145 151 157 161 165 184 194 203 211 218 225 303 309 314 319 323 327 331 335 338 341 344 347
9
103 113 130 139 147 154 159 164 182 193 203 212 220 227 305 311 317 322 327 331 335 339 342 346 421 423 426 429
92
8
113 133 144 153 160 166 190 203 214 224 305 312 319 325 331 336 341 345 421 425 428 431 434 437 439 442 444 446 448
101 113 132 142 150 157 162 167 192 203 213 222 301 309 315 321 326 331 336 340 344 347 422 426 428 431 434 436 438
83
75
7
112 137 150 161 182 201 217 302 313 322 330 337 343 421 426 430 434 438 442 445 447 450 452 455 457 459 461 462 464 465 467
113 135 147 156 164 187 203 216 227 308 317 324 331 337 342 347 423 427 431 434 438 440 443 446 448 450 452 454 456 458
99
81
71
62
6
111 139 155 166 199 218 305 318 328 337 345 423 429 434 439 443 446 450 453 455 458 460 462 464 466 480 480 480 480 480 480 480
91
96
77
66
52
48
5
109 143 161 195 220 311 326 337 347 427 434 440 445 449 453 457 460 462 465 467 480 480 480 480 480 480 480 480 480 480 480 480 480
79
61
71
53
48
43
39
4
106 150 188 225 321 339 424 434 442 449 454 459 463 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
67
47
38
48
42
36
28
26
3
93
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
76
47
35
26
21
17
14
11
10
94
65
48
41
33
27
23
21
92
72
53
48
43
39
97
77
66
52
48
94
78
69
96
81
93
99
104 109 120 125 130 134 138 142 145 149 152 154 157 159 162 164 166 180
103 108 113 125 130 135 140 144 147 151 154 157 159 162 164 166 182 188 193 198
101 108 113 126 132 137 142 146 150 153 157 160 162 165 167 186 192 198 203 208 213 218
83
76
100 107 120 127 134 139 144 149 153 157 160 163 166 183 191 197 204 209 215 220 225 301 305 309
81
71
62
106 120 128 136 142 148 153 157 161 164 180 189 197 204 211 217 222 300 305 309 314 318 322 325 329
91
74
64
52
104 113 130 138 145 151 157 161 166 185 195 203 211 219 225 303 309 314 319 323 328 331 335 338 342 345 347
81
68
52
48
44
101 113 131 141 149 156 162 167 191 202 212 221 301 308 314 320 326 330 335 339 343 347 422 425 428 431 433 436 438
75
60
48
43
37
32
111 133 145 155 162 183 199 212 223 305 314 322 328 334 340 345 421 425 429 433 436 439 441 444 446 449 451 453 455 456
80
62
48
42
36
28
26
108 136 152 164 193 213 301 314 325 334 342 420 426 432 436 440 444 448 451 453 456 458 461 463 465 466 480 480 480 480 480 480
69
48
39
30
25
20
18
16
-
-
-
-
-
-
-
-
-
-
8
67
43
28
22
18
14
12
10
92
51
40
30
23
19
16
14
11
82
53
46
38
30
26
21
18
80
62
48
42
36
28
26
96
72
52
46
41
35
28
93
72
53
48
43
39
90
72
60
49
45
97
77
66
52
48
94
77
67
53
92
76
67
97
80
71
94
79
99
82
92
97
101 104 107 111 113 123 126 130 133
103 107 110 113 123 127 131 134 140 143 145
102 106 110 120 124 128 132 136 139 142 145 148 150 153
83
75
100 105 110 120 125 130 134 138 141 145 148 151 153 156 158 161 163
81
71
62
104 109 120 126 131 136 140 144 148 151 154 157 160 162 165 167 184 189 195
82
72
61
50
101 108 120 127 133 138 143 148 152 155 159 162 165 167 185 192 198 204 209 215 219 224
78
65
51
47
42
105 113 128 135 141 147 152 156 160 164 167 187 195 203 209 216 221 227 304 308 313 317 321 324
79
64
50
45
40
35
101 112 129 138 146 152 158 163 167 190 200 209 217 224 303 309 315 320 325 329 333 337 341 344 347 422 425
71
51
44
37
30
26
22
109 131 143 153 161 167 195 209 220 302 311 319 326 332 338 343 347 423 427 431 434 437 440 443 445 447 449 451 453
70
48
39
30
25
21
18
15
-
-
-
-
-
-
-
-
-
-
62
40
27
21
16
13
10
9
7
77
48
36
26
21
17
14
11
10
97
53
43
32
26
20
17
14
12
80
52
44
36
28
23
20
18
95
66
48
41
33
27
23
20
81
63
48
42
35
28
26
94
70
51
45
39
33
28
81
66
51
45
40
35
93
72
53
48
43
38
99
77
63
50
45
41
92
73
60
50
46
97
77
65
51
48
90
73
63
51
95
77
67
53
99
80
70
61
93
77
68
97
80
71
92
77
95
80
99
82
91
94
97
102 105 107
101 104 107 110 113 122 125
82
74
103 107 110 113 123 127 130 133 136 139
83
74
65
102 106 110 120 124 128 132 136 139 142 145 148 150 153
81
69
53
49
105 110 120 125 130 135 139 142 146 149 152 155 157 160 162 164 166
81
68
52
48
43
102 108 120 126 132 137 142 146 150 154 157 160 163 165 180 186 192 198 204 209 214
76
60
48
42
37
31
105 112 127 134 141 146 151 156 160 163 167 186 194 201 208 214 220 225 302 307 312 316 320 323
74
52
45
38
31
26
23
110 127 138 146 153 159 165 184 196 206 215 223 303 310 316 321 326 331 335 339 343 347 422 425 428 430 433
70
48
39
30
25
20
18
15
105 133 149 161 187 207 224 309 320 330 338 345 423 428 433 438 442 445 448 451 454 456 459 461 463 464 466 480 480 480 480
46
28
21
16
12
9
7
6
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
Tables for UPS Model Number Where Digits 1-3 are AS6 or ASF
106 140 158 188 214 306 321 333 343 424 431 437 442 447 451 454 458 460 463 465 480 480 480 480 480 480 480 480 480 480 480 480
46
28
20
16
12
9
8
6
5
7.6.1
-
-
-
-
-
-
-
-
-
-
104 148 184 222 319 336 422 432 441 447 453 458 462 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
46
28
20
15
12
9
7
6
5
Estimated Battery Run Times
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
-
-
30%
-
-
40%
90%
-
50%
100%
-
60%
-
-
70%
-
-
80%
10%
-
90%
20%
-
100%
101 167 314 347 438 451 460 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
20
40%
10%
15
50%
28
25
20
18
15
2
7.6
20kVA/
18kW
15kVA/
13.5kW
10kVA/
9kW
5kVA/
4.5kW
9
7
80%
11
6
90%
60%
5
100%
70%
1
16-bay, two-phase, no transformer, unit Type N (& UPS model number 6 = N)
UPS Load
Rating Level
Table 51
Specifications
Liebert® APS™
Liebert® APS™
94
13
14
15
16
17
18
19
20
# Battery Strings
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
102 113 130 139 147 154 159 164 181 193 203 211 219 227 305 311 317 322 327 331 335 339 342 345 420 423 426 429
19
26
42
91 160 301 337 430 444 455 462 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
83
110 134 148 159 167 196 212 226 309 318 327 334 340 346 423 428 432 436 439 443 445 448 451 453 455 457 459 461 462 464 465
108 136 152 163 192 212 300 313 324 333 341 420 426 431 436 440 444 447 450 453 456 458 460 462 464 466 480 480 480 480 480 480
73
46
34
26
20
17
14
12
10
91
63
48
40
33
27
23
21
98
74
53
48
43
38
32
96
77
66
52
48
94
78
70
97
81
93
99
105 109 120 125 130 135 139 142 146 149 152 155 157 160 162 164 166 180
103 109 120 126 131 136 140 144 148 151 154 157 160 162 165 167 183 189 194 199
102 108 120 126 132 137 142 146 150 154 157 160 163 165 180 187 193 199 204 209 214 218
90
76
100 107 120 127 134 139 144 149 153 157 160 163 166 183 191 197 204 209 215 220 225 301 305 309
81
72
63
105 113 128 135 141 147 152 156 160 164 167 187 195 203 209 216 221 227 304 308 313 317 321 324 328
91
74
64
52
103 112 128 137 144 150 156 160 165 182 192 201 209 216 223 301 307 312 317 322 326 330 333 337 340 343 346
80
68
52
48
44
111 129 139 147 154 160 165 186 198 208 217 225 305 311 317 323 328 332 337 341 344 420 423 426 429 431 434 436
91
71
53
48
44
39
109 130 143 152 160 167 194 207 219 301 310 318 325 331 337 342 346 423 427 430 433 436 439 442 444 447 449 451 453 454
78
61
48
42
36
30
26
105 133 149 161 187 207 224 309 320 330 338 345 423 429 433 438 442 445 448 451 454 456 459 461 463 465 466 480 480 480 480 480
67
47
38
28
25
21
18
16
144 166 214 312 331 345 428 437 444 450 455 459 463 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
104 138 157 185 212 304 319 332 342 422 429 436 441 446 450 453 457 460 462 465 467 480 480 480 480 480 480 480 480 480 480 480 480
76
53
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
8
65
42
28
22
18
14
12
10
11
83
50
40
28
23
19
16
14
15
18
80
53
45
38
30
26
22
22
99
70
50
44
37
30
26
26
28
95
71
52
46
41
35
35
39
92
72
53
48
44
42
45
90
72
60
50
48
97
77
66
52
50
53
94
77
67
62
67
92
76
71
97
80
75
79
94
82
99
92
97
100 104 107 111 113 123 126 130 133
103 107 110 120 124 127 131 134 137 140 143
102 106 110 120 124 128 132 136 139 142 145 148 150 153
90
100 105 110 120 125 130 134 138 141 145 148 151 153 156 158 161 163
81
72
103 109 120 126 131 136 140 144 148 151 154 157 160 162 164 167 183 189 194
82
72
61
100 107 113 126 132 138 143 147 151 155 158 161 164 167 184 191 197 203 208 213 218 223
78
65
51
47
104 112 126 134 140 146 151 155 159 163 166 185 193 200 207 214 219 225 302 307 311 315 319 323
79
64
50
45
40
110 126 136 144 151 156 161 166 186 196 205 214 221 300 306 312 317 322 327 331 335 338 342 345 420 423
79
62
48
42
36
30
107 128 141 151 159 165 190 204 216 226 307 315 322 329 334 340 344 421 425 428 432 435 438 440 443 445 447 449 451
68
47
39
30
25
21
18
-
-
-
-
-
-
-
-
-
-
60
39
27
20
16
13
10
9
7
76
47
35
26
20
17
14
11
10
95
53
42
32
25
20
17
14
12
79
52
44
36
28
23
20
18
94
65
48
41
33
27
23
20
80
62
48
42
35
28
26
93
69
51
45
39
33
28
81
66
50
45
40
35
92
71
53
48
43
38
99
76
63
50
45
41
91
73
60
50
46
97
77
65
51
48
90
73
63
52
95
77
67
53
99
80
70
61
93
77
69
97
80
72
92
78
95
80
99
83
92
95
102 105
100 104 107 110 113 122
83
75
103 107 110 113 123 126 130 133 136
83
74
65
101 106 110 113 124 128 132 135 139 142 145 147 150
80
69
53
50
104 109 113 125 130 134 138 142 145 148 151 154 157 159 161 164
81
68
52
48
44
101 107 113 125 131 136 141 145 149 153 156 159 162 165 167 184 191 197 202 207
75
53
48
42
37
32
103 111 125 133 139 145 150 155 159 162 166 183 191 198 205 212 218 223 300 305 310 314 318
73
52
45
38
31
26
23
108 125 136 144 152 158 163 180 192 202 212 220 300 306 313 318 324 328 333 337 341 344 420 423 426 428
69
48
39
28
25
20
18
15
102 129 146 159 180 201 218 304 316 326 334 341 420 425 430 435 439 443 446 449 452 454 457 459 461 463 464 466 480 480
46
28
20
15
11
9
7
6
5
-
-
-
-
-
-
-
-
-
-
102 136 155 180 207 300 316 329 339 420 427 433 439 444 448 452 455 458 461 463 466 480 480 480 480 480 480 480 480 480 480 480
45
28
20
15
12
9
8
6
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
100 145 167 216 314 333 346 429 438 445 451 456 460 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
44
27
20
15
11
9
8
6
5
99
62
46
37
112 132 143 152 159 165 188 201 212 222 303 311 318 324 330 335 340 344 420 424 427 430 433 436 438 441 443 445 447
111 133 145 155 163 183 199 212 224 306 314 322 329 335 340 345 421 426 429 433 436 439 442 444 447 449 451 453 455 456
98
12
100 113 131 141 149 156 162 167 190 202 212 221 301 308 314 320 325 330 335 339 343 346 422 425 428 431 433 436 438
83
11
104 120 130 138 145 152 157 162 166 185 195 204 212 219 226 304 309 314 319 324 328 332 335 339 342 345 420
10
14
94
76
80
71
93
9
40%
69
52
65
52
76
8
50%
47
41
48
43
62
7
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
20kVA/
18kW
15kVA/
13.5kW
10kVA/
9kW
5kVA/
4.5kW
28
25
35
28
48
6
9
20
18
39
5
11
7
80%
26
4
60%
6
90%
16
3
70%
5
100%
2
16-bay, two-phase, no transformer unit Type R (& UPS model number 6 = R)
UPS
Load
Rating Level 1
Table 52
Specifications
95
17
18
19
20
# Battery Strings
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
103 113 130 139 147 154 159 164 182 193 203 212 220 227 305 311 317 322 327 331 335 339 342 346 421 423 426
113 133 144 153 160 166 190 203 214 224 305 312 319 325 331 336 341 345 421 425 428 431 434 437 439 442 444 446
112 137 150 161 182 201 217 302 313 322 330 337 343 421 426 430 434 438 442 445 447 450 452 455 457 459 461 462 464 465
109 143 161 195 220 311 326 337 347 427 434 440 445 449 453 457 460 462 465 467 480 480 480 480 480 480 480 480 480 480 480 480
-
-
-
-
-
-
-
-
20%
10%
100%
90%
80%
70%
60%
50%
-
-
30%
-
-
40%
10%
-
50%
20%
-
60%
-
-
70%
-
-
80%
30%
-
40%
-
90%
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
76
106 120 128 136 142 148 153 157 161 164 180 189 197 204 211 217 222 300 305 309 314 318 322 325
101 113 131 141 149 156 162 167 191 202 212 221 301 308 314 320 326 330 335 339 343 347 422 425 428 431 433 436
108 136 152 164 193 213 301 314 325 334 342 420 426 432 436 440 444 448 451 453 456 458 461 463 465 466 480 480 480 480 480
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
8
67
43
28
22
18
14
12
10
92
51
40
30
23
19
16
14
11
82
53
46
38
30
26
21
18
22
80
62
48
42
36
28
26
28
96
72
52
46
41
35
35
93
72
53
48
43
39
90
72
60
49
45
97
77
66
52
48
94
77
67
53
92
76
67
97
80
71
94
79
99
82
92
97
101 104 107 111 113 123 126 130
103 107 110 113 123 127 131 134 140 143
102 106 110 120 124 128 132 136 139 142 145 148 150
83
75
100 105 110 120 125 130 134 138 141 145 148 151 153 156 158 161
81
71
62
104 109 120 126 131 136 140 144 148 151 154 157 160 162 165 167 184 189
82
72
61
50
101 108 120 127 133 138 143 148 152 155 159 162 165 167 185 192 198 204 209 215 219
78
65
51
47
42
105 113 128 135 141 147 152 156 160 164 167 187 195 203 209 216 221 227 304 308 313 317 321
79
64
50
45
40
101 112 129 138 146 152 158 163 167 190 200 209 217 224 303 309 315 320 325 329 333 337 341 344 347 422
71
51
44
37
30
26
109 131 143 153 161 167 195 209 220 302 311 319 326 332 338 343 347 423 427 431 434 437 440 443 445 447 449 451
70
48
39
30
25
21
18
15
-
-
-
-
-
-
-
-
-
-
62
40
27
21
16
13
10
9
7
77
48
36
26
21
17
14
11
10
97
53
43
32
26
20
17
14
12
80
52
44
36
28
23
20
18
95
66
48
41
33
27
23
20
81
63
48
42
35
28
26
94
70
51
45
39
33
28
81
66
51
45
40
35
93
72
53
48
43
38
99
77
63
50
45
41
92
73
60
50
46
97
77
65
51
48
90
73
63
51
95
77
67
53
99
80
70
61
93
77
68
97
80
71
92
77
95
80
99
82
91
94
102 105
101 104 107 110 113 122
82
74
103 107 110 113 123 127 130 133 136
83
74
65
102 106 110 120 124 128 132 136 139 142 145 148 150
81
69
53
49
105 110 120 125 130 135 139 142 146 149 152 155 157 160 162 164
81
68
52
48
43
102 108 120 126 132 137 142 146 150 154 157 160 163 165 180 186 192 198 204 209
76
60
48
42
37
31
105 112 127 134 141 146 151 156 160 163 167 186 194 201 208 214 220 225 302 307 312 316 320
74
52
45
38
31
26
23
110 127 138 146 153 159 165 184 196 206 215 223 303 310 316 321 326 331 335 339 343 347 422 425 428 430
70
48
39
30
25
20
18
15
105 133 149 161 187 207 224 309 320 330 338 345 423 428 433 438 442 445 448 451 454 456 459 461 463 464 466 480 480 480
46
28
21
16
12
9
7
6
5
106 140 158 188 214 306 321 333 343 424 431 437 442 447 451 454 458 460 463 465 480 480 480 480 480 480 480 480 480 480 480
46
28
20
16
12
9
8
6
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
104 148 184 222 319 336 422 432 441 447 453 458 462 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
46
104 109 120 125 130 134 138 142 145 149 152 154 157 159 162 164 166
111 133 145 155 162 183 199 212 223 305 314 322 328 334 340 345 421 425 429 433 436 439 441 444 446 449 451 453 455
80
99
100%
-
-
94
65
97
93
103 108 113 125 130 135 140 144 147 151 154 157 159 162 164 166 182 188 193
104 113 130 138 145 151 157 161 166 185 195 203 211 219 225 303 309 314 319 323 328 331 335 338 342 345
81
96
81
101 108 113 126 132 137 142 146 150 153 157 160 162 165 167 186 192 198 203 208 213
83
76
-
69
48
92
72
94
78
69
100 107 120 127 134 139 144 149 153 157 160 163 166 183 191 197 204 209 215 220 225 301 305
81
71
62
-
47
35
75
60
91
74
64
52
10%
28
20
62
48
77
66
52
48
20%
-
-
48
41
68
52
48
44
-
39
30
53
48
43
39
-
26
21
48
43
37
32
30%
15
12
42
36
28
26
40%
-
-
33
27
23
21
-
25
20
18
16
-
17
14
11
10
50%
9
7
6
5
60%
-
-
-
-
-
106 150 188 225 321 339 424 434 442 449 454 459 463 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
67
16
111 139 155 166 199 218 305 318 328 337 345 423 429 434 439 443 446 450 453 455 458 460 462 464 466 480 480 480 480 480 480
91
15
113 135 147 156 164 187 203 216 227 308 317 324 331 337 342 347 423 427 431 434 438 440 443 446 448 450 452 454 456
99
14
-
45
27
79
61
77
96
13
101 113 132 142 150 157 162 167 192 203 213 222 301 309 315 321 326 331 336 340 344 347 422 426 428 431 434 436
83
12
104 113 129 138 145 151 157 161 165 184 194 203 211 218 225 303 309 314 319 323 327 331 335 338 341 344
11
70%
-
20%
47
38
53
71
81
71
92
10
80%
-
30%
20
15
42
48
66
52
75
9
-
-
40%
25
28
48
43
62
8
90%
-
50%
9
11
36
28
48
7
- 101 167 314 347 438 451 460 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
-
60%
20
18
39
6
-
-
70%
7
6
26
5
10%
-
80%
15
4
100%
-
90%
5
3
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
20kVA/
18kW
15kVA/
13.5kW
10kVA/
9kW
5kVA/
4.5kW
-
100%
2
16-bay, two-phase, no transformer unit Type B (& UPS model number 6 = B)
UPS
Load
Rating Level 1
Table 53
Specifications
Liebert® APS™
Liebert® APS™
96
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
100%
90%
80%
70%
60%
50%
40%
30%
20%
10%
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
98
112 132 143 152 159 165 188 201 212 222 303 311 318 324 330 335 340 344 420 424 427 430 433 436 438 441 443 445
110 134 148 159 167 196 212 226 309 318 327 334 340 346 423 428 432 436 439 443 445 448 451 453 455 457 459 461 462 464
111 133 145 155 163 183 199 212 224 306 314 322 329 335 340 345 421 426 429 433 436 439 442 444 447 449 451 453 455
108 136 152 163 192 212 300 313 324 333 341 420 426 431 436 440 444 447 450 453 456 458 460 462 464 466 480 480 480 480 480
83
76
94
73
46
34
26
20
17
14
12
10
91
63
48
40
33
27
23
21
98
74
53
48
43
38
32
96
77
66
52
48
94
78
70
97
81
93
99
105 109 120 125 130 135 139 142 146 149 152 155 157 160 162 164
103 109 120 126 131 136 140 144 148 151 154 157 160 162 165 167 183 189
102 108 120 126 132 137 142 146 150 154 157 160 163 165 180 187 193 199 204 209
90
76
100 107 120 127 134 139 144 149 153 157 160 163 166 183 191 197 204 209 215 220 225 301
81
72
63
105 113 128 135 141 147 152 156 160 164 167 187 195 203 209 216 221 227 304 308 313 317 321
91
74
64
52
103 112 128 137 144 150 156 160 165 182 192 201 209 216 223 301 307 312 317 322 326 330 333 337 340
80
68
52
48
44
111 129 139 147 154 160 165 186 198 208 217 225 305 311 317 323 328 332 337 341 344 420 423 426 429 431
91
71
53
48
44
39
109 130 143 152 160 167 194 207 219 301 310 318 325 331 337 342 346 423 427 430 433 436 439 442 444 447 449 451
78
61
48
42
36
30
26
105 133 149 161 187 207 224 309 320 330 338 345 423 429 433 438 442 445 448 451 454 456 459 461 463 465 466 480 480 480
67
47
38
28
25
21
18
16
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
8
65
42
28
22
18
14
12
10
83
50
40
28
23
19
16
14
11
80
53
45
38
30
26
22
18
99
70
50
44
37
30
26
22
95
71
52
46
41
35
28
92
72
53
48
44
39
90
72
60
50
45
97
77
66
52
48
94
77
67
53
92
76
67
97
80
71
94
79
99
82
92
97
100 104 107 111 113 123 126 130
103 107 110 120 124 127 131 134 137 140
102 106 110 120 124 128 132 136 139 142 145 148 150
90
75
100 105 110 120 125 130 134 138 141 145 148 151 153 156 158 161
81
72
62
103 109 120 126 131 136 140 144 148 151 154 157 160 162 164 167 183 189
82
72
61
50
100 107 113 126 132 138 143 147 151 155 158 161 164 167 184 191 197 203 208 213 218
78
65
51
47
42
104 112 126 134 140 146 151 155 159 163 166 185 193 200 207 214 219 225 302 307 311 315 319
79
64
50
45
40
35
110 126 136 144 151 156 161 166 186 196 205 214 221 300 306 312 317 322 327 331 335 338 342 345 420
79
62
48
42
36
30
26
107 128 141 151 159 165 190 204 216 226 307 315 322 329 334 340 344 421 425 428 432 435 438 440 443 445 447 449
68
47
39
30
25
21
18
15
-
-
-
-
-
-
-
-
-
-
69
48
39
28
25
20
18
15
79
52
44
36
28
23
20
18
94
65
48
41
33
27
23
20
80
62
48
42
35
28
26
93
69
51
45
39
33
28
81
66
50
45
40
35
92
71
53
48
43
38
99
76
63
50
45
41
91
73
60
50
46
97
77
65
51
48
90
73
63
52
95
77
67
53
99
80
70
61
93
77
69
97
80
72
92
78
95
80
99
83
92
102
100 104 107 110 113
83
75
103 107 110 113 123 126 130 133
83
74
65
101 106 110 113 124 128 132 135 139 142 145 147
80
69
53
50
104 109 113 125 130 134 138 142 145 148 151 154 157 159 161
81
68
52
48
44
101 107 113 125 131 136 141 145 149 153 156 159 162 165 167 184 191 197 202
75
53
48
42
37
32
103 111 125 133 139 145 150 155 159 162 166 183 191 198 205 212 218 223 300 305 310 314
73
52
45
38
31
26
23
-
-
-
-
-
-
-
-
-
95
53
42
32
25
20
17
14
12
102 129 146 159 180 201 218 304 316 326 334 341 420 425 430 435 439 443 446 449 452 454 457 459 461 463 464 466 480
76
47
35
26
20
17
14
11
10
-
60
39
27
20
16
13
10
9
7
108 125 136 144 152 158 163 180 192 202 212 220 300 306 313 318 324 328 333 337 341 344 420 423 426
46
28
20
15
11
9
7
6
5
102 136 155 180 207 300 316 329 339 420 427 433 439 444 448 452 455 458 461 463 466 480 480 480 480 480 480 480 480 480 480
45
28
20
15
12
9
8
6
5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
144 166 214 312 331 345 428 437 444 450 455 459 463 466 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
104 138 157 185 212 304 319 332 342 422 429 436 441 446 450 453 457 460 462 465 467 480 480 480 480 480 480 480 480 480 480 480
76
53
52
69
100 145 167 216 314 333 346 429 438 445 451 456 460 464 467 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
44
27
20
15
11
9
8
6
5
99
62
46
37
41
47
102 113 130 139 147 154 159 164 181 193 203 211 219 227 305 311 317 322 327 331 335 339 342 345 420 423 426
100 113 131 141 149 156 162 167 190 202 212 221 301 308 314 320 325 330 335 339 343 346 422 425 428 431 433 436
83
40%
-
-
25
28
80
71
-
-
-
-
-
9
65
52
-
35
50%
34
60%
33
-
32
-
31
70%
30
80%
29
-
28
-
27
90%
26
100%
25
- 91 160 301 337 430 444 455 462 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480 480
24
10%
23
- 42
22
- 26
21
20%
20
30%
19
- 19
18
- 14
17
# Battery Strings
40%
16
50%
15
- 11
14
104 120 130 138 145 152 157 162 166 185 195 204 212 219 226 304 309 314 319 324 328 332 335 339 342 345
13
-
48
43
93
12
60%
35
28
76
11
70%
20
18
62
10
Run times in this table are approximate. They are based on new, fully charged standard battery modules at a temperature of 25°C (77°F) with 100% resistive UPS loading.
20kVA/
18kW
15kVA/
13.5kW
10kVA/
9kW
5kVA/
4.5kW
7
6
48
9
-
39
8
-
26
7
80%
16
6
90%
5
5
-
4
100%
3
16-bay, two-phase, no transformer unit Type F (& UPS model number 6 = F)
UPS
Load
Rating Level 1 2
Table 54
Specifications
Specifications
NOTES
97
Liebert® APS™
Specifications
Liebert® APS™
98
Technical Support / Service
Web Site
www.liebert.com
Monitoring
liebert.monitoring@emerson.com
800-222-5877
Outside North America: +00800 1155 4499
Single-Phase UPS & Server Cabinets
liebert.upstech@emerson.com
800-222-5877
Outside North America: +00800 1155 4499
Three-Phase UPS & Power Systems
800-543-2378
Outside North America: 614-841-6598
Environmental Systems
800-543-2778
Outside the United States: 614-888-0246
Locations
While every precaution has been taken to ensure the accuracy
and completeness of this literature, Liebert Corporation assumes no
responsibility and disclaims all liability for damages resulting from use of
this information or for any errors or omissions.
© 2013 Liebert Corporation
All rights reserved throughout the world. Specifications subject to change
without notice.
® Liebert is a registered trademark of Liebert Corporation.
All names referred to are trademarks
or registered trademarks of their respective owners.
United States
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Europe
Via Leonardo Da Vinci 8
Zona Industriale Tognana
35028 Piove Di Sacco (PD) Italy
+39 049 9719 111
Fax: +39 049 5841 257
Asia
29/F, The Orient Square Building
F. Ortigas Jr. Road, Ortigas Center
Pasig City 1605
Philippines
+63 2 687 6615
Fax: +63 2 730 9572
SL-55010_REV3_12-13
Emerson Network Power
Division: Liebert
Web: www.emerson.com
www.EmersonNetworkPower.com