Alpha 1500 Instruction manual

Add to my manuals
32 Pages

advertisement

Alpha 1500 Instruction manual | Manualzz
ENGLISH
®
ALPHA SPOT HPE 1500
C61325
INSTRUCTION MANUAL
INDEX
Pag.
Contents
2
Safety information
3
Unpacking and preparation
4
Installation and start-up
5
Control panel
7
Menu setting
15
Maintenance
23
Technical information
23
Cause and solution of problems
24
Channel functions
Congratulations on choosing a Clay Paky product!
We thank you for your custom.
Please note that this product, as all the others in the rich Clay
Paky range, has been designed and made with total quality to
ensure excellent performance and best meet your expectations
and requirements.
Carefully read this instruction manual in its entirety and keep it
safe for future reference. It is essential to know the information
and comply with the instructions given in this manual to ensure
the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting
or to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instruction manual at any time and
without prior notice.
1
SAFETY INFORMATION
• Installation
Make sure all parts for fixing the projector are in a good state of repair.
Make sure the point of anchorage is stable before positioning the projector.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if
the primary support system fails, the fitting falls as little as possible.
If the safety chain gets used, it needs to be replaced with a genuine spare.
1500W
• Minimum distance of illuminated objects
The projector needs to be positioned so that the objects hit by the beam of light are at least 5 metres
(16'5'') from the lens of the projector.
5
• Minimum distance from flammable materials
The projector must be positioned so that any flammable materials are at least 0.20 metres (8") from
every point on the surface of the fitting.
• Mounting surfaces
It is permissible to mount the fitting on normally flammable surfaces.
• Maximum ambient temperature
Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
IP20
• IP20 protection rating
The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first
digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0).
• Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class I appliance
according to standard EN 60598-1).
It is, moreover, recommended to protect the supply lines of the projectors from indirect contact
and/or shorting to earth by using appropriately sized residual current devices.
• Connection to mains supply
Connection to the electricity mains must be carried out by a qualified electrical installer.
Check that the mains frequency and voltage correspond to those for which the projector is designed
as given on the electrical data label.
This label also gives the input power to which you need to refer to evaluate the maximum number
of fittings to connect to the electricity line, in order to avoid overloading.
• Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting, in a thermally
steady state, is 150°C (302°F).
• Maintenance
Before starting any maintenance work or cleaning the projector, cut off power from the mains supply.
After switching off, do not remove any parts of the fitting for at least 10 minutes. After this time the
likelihood of the lamp exploding is virtually nill. If it is necessary to replace the lamp, wait for another
20 minutes to avoid getting burnt.
The fitting is designed to hold in any splinters produced by a lamp exploding. The lenses must be
mounted and, if visibly damaged, they have to be replaced with genuine spares.
• Lamp
The fitting mounts a high-pressure lamp that needs an external igniter. This igniter is fitted onto the
apparatus.
- Carefully read the "operating instructions" provided by the lamp manufacturer.
- Immediately replace the lamp if damaged or deformed by heat.
Pb
• Battery
This product contains a rechargeable lead-acid battery. To preserve the environment, please
dispose the battery at the end of its life according to the regulation in force. Instructions on how to
remove the battery from the product are available on www.claypaky.it
The products referred to in this manual conform to the European Community Directives to which
they are subject:
• Low Voltage 2006/95/CE
• Electromagnetic Compatibility 2004/108/CE
ALPHA SPOT HPE 1500
2
UNPACKING AND PREPARATION
1
Lamp 1500W
(fitted into projector)
099105
2 x 183102/802
Packing contents - Fig. 1
2
3
45°
45°
45°
45°
45°
UNLOCKED
45°
LOCKED
LOCKED
UNLOCKED
°
90
°
90
°
90
°
90
PAN Mechanism Lock and Release (every 90°) - Fig. 2
TILT Mechanism Lock and Release (every 45°) - Fig. 3
ALPHA SPOT HPE 1500
3
INSTALLATION AND START-UP
4
Installing the projector - Fig. 4
The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
WARNING: with the exception of when the projector is positioned on the floor, the safety cable must be fitted. (Cod. 105041/003 available on request).
This must be securely fixed to the support structure of the projector and then connected to the fixing point at the centre of the base.
5
1
2
2
1
Connecting and disconnecting power cable - Fig. 5
ALPHA SPOT HPE 1500
4
3
CONTROL PANEL
6
Mains
L
N
Connecting to the mains supply - Fig. 6
7
DMX 512
5 PIN
5
4
3
1
2
SCREEN
SIGNAL
SIGNAL
DMX 512
DMX 512
3 PIN
SIGNAL
2
SCREEN
1
3
SIGNAL
Connecting to the control signal line (DMX) - Fig. 7
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AWG, low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female
connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.
8
Fixture ID
Dmx Address
2
1
MAINS
Warning Message
Switching on the projector - Fig. 8
Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:
Model
Alpha SPOT HPE
1500
Firmware
Version X.X.X
Date - Hour
xxx (Fixture ID)
Dmx Address xxx
System errors
E: .........................
W: .........................
On conclusion of resetting in case of absence of dmx signal, Pan and Tilt move to the “Home” position (Pan 50% - Tilt 50%). The control panel (Fig.
8) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions:
rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set).
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the
key will be cancelled.
Continue
ALPHA SPOT HPE 1500
5
➔
9
28
28
Reversal of the display - Fig. 9
To activate this function, press UP
and DOWN
keys simultaneously while the display is in the rest mode. This status will be memorised and
maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
The address can also be set with the projector switched off.
Setting the address: see pag. 8.
Setting the projector Fixture ID
On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255).
The Fixture ID address can be set with the projector switched off.
Setting the Fixture ID: see pag. 8.
Functions of the buttons - Using the menu
Confirms the displayed value, or activates the displayed function, or enters the successive
menu.
Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.
DOWN
Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.
Return to the top level
Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.
UP
LEFT
RIGHT
USING THE MENU:
once – “Main Menu” appears on the display.
1) Press
2) Use the UP
and DOWN
keys to select the menu to be used:
• Setup (Setup Menu): To set the setting options.
• Option (Option Menu): To set the operating options.
• Informations (Informations Menu): To read the counters, software version and other information.
• Manual Control (Manual control Menu): To trigger the test and manual control functions.
• Test (Test Menu): To check the proper functionning of effects.
• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel.
To enable the "Advanced" see pag. 14
3) Press
to display the first item in the selected menu.
4) Use the UP
and DOWN
keys to select the MENU items.
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press
to momentarily activate the display and thus access the settings. Once the required operations have been carried out,
the display will switch off again after a wait time of 30 seconds.
ALPHA SPOT HPE 1500
6
MENU SETTING
MAIN MENU
1
2
Set Up
Dmx
Address
Channel
Mode
3
Option
Lamp Dmx
Pan / Tilt
Information
Invert
Pan
System
Errors
Fixture
Hours
Invert
Tilt
Fixture ID
Lamp
Hours
Swap
Pan-Tilt
Ethernet
Interface
Lamp
Strikes
Encoder
Pan-Tilt
Color
Option
Color
Mixing
System
Version
Fixed Wheel
Shortcut
Information
Board
diagnostic
Macro Color
Adjustment
Manual
Control
Shutter
Shutter
On Error
Dmx
Monitor
Dimmer On
Shutter
Test
Autofocus
Mode
Advanced
Fans
Monitor
Limited Zoom
Range
Network
parameters
Complete
Zoom Range
Macro
Effects
4
Macro group
size
Macro
fixture Id
Manual
Control
Lamp
Silent
Mode
Standard
Quiet
Reset
Power Mode
1500-1200
Full fan speed
1200
Low fan speed
Channel
1500-1200
Auto fan speed
Display
5
Setting
Test
Default
Preset
User
Preset 1
Pan / Tilt
6
Advanced
Access code
1234
User
Preset 2
Colour
User
Preset 3
Upload
Firmware
Beam
Setup
Model
Gobo
Calibration
All
Continue
ALPHA SPOT HPE 1500
7
➔
NOTE: On grey the default options
Set Up
Dmx
Address
SET UP MENU
DMX ADDRESS
NOTE: without the DMX signal the Address (XXX) flashing
Allows you to select the DMX ADDRESS
1) Press
- the current DMX Adress appear on the display.
2) Use the UP , DOWN
, RIGHT
keys to plan the DMX
Address.
3) Press
to confirm the selection or LEFT
to keep current settings.
Address xxx
Channel
Mode
CHANNEL MODE
Allows you to select a channel arrangement from the two available.
1) Press
- the current settings appear on the display (Standard or
Vector).
2) Use the UP
and DOWN
keys to select one of the following
settings:
- Standard
- Vector
3) Press
to confirm the selection or LEFT
to keep current settings.
Standard
Vector
Fixture Id
FIXTURE ID
Allows you to select the FIXTURE ID
1) Press
- the current Fixture ID appear on the display.
2) Use the UP , DOWN
, RIGHT
keys to plan the Fixture ID.
3) Press
to confirm the selection or LEFT
to keep current settings.
Value xxx
ETHERNET INTERFACE
It lets you set the Ethernet settings to be attributed to the projector.
1) Premere
.
2) Use the UP
and DOWN
keys to select the “Ethernet Interface”
options to set:
Ethernet
Interface
Control
Protocol
Control Protocol
It lets you select the “Control Protocol” Art-net to assign according to the
control unit used:
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
- Disabled
- Art-net on IP 2
- Art-net on IP 10
3) Press
to confirm the selection or LEFT
to keep the current setting.
Repeat on DMX
It lets you enable the transmission of the Ethernet protocol by DMX signal
to all the connected projectors.
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
- Disabled: DMX transmission disabled.
- Enabled on primary: DMX transmission enabled.
3) Press
to confirm the selection or LEFT
to keep the current setting.
Repeat on
DMX
Universe
It lets you assign the “Universe” number to be assigned to a series of
projectors.
1) Press
– the current Universe address appears on the display.
2) Use the UP
, DOWN
, RIGHT
keys to set the Universe address.
3) Press
to confirm the selection or LEFT
to keep the current setting.
Universe
ALPHA SPOT HPE 1500
8
OPTIONS MENU
On
Option
LAMP DMX
Used for enabling lamp remote control channel.
1) Press
- the current settings appear on the display (On or Off).
and DOWN
keys to enable (On) or disable (Off)
2) Use the UP
the lamp remote control channel.
3) Press
to confirm the selection or LEFT
to keep current settings.
Lamp Dmx
Off
Pan / Tilt
Invert
Pan
PAN / TILT
Invert pan
Used for reversing Pan movement.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
PAN inversion.
3) Press
to confirm the selection or LEFT
to keep current settings.
On
Off
Invert
Tilt
On
Invert tilt
Used for reversing tilt movement.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
Tilt inversion.
3) Press
to confirm the selection or LEFT
to keep current settings.
Off
Swap
Pan-Tilt
On
Swap Pan-Tilt
Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine).
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
Pan and Tilt channel swap.
3) Press
to confirm the selection or LEFT
tto keep current settings.
Off
Encoder
Pan-Tilt
On
Encoder Pan-Tilt
Used for enabling the Pan / Tilt encoders.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
Pan / Tilt encoders.
3) Press
to confirm the selection or LEFT
to keep current settings.
Off
Color
Color
Mixing
RGB
COLOR
Color mixing
Used for reversing the CMY color mixing system.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys select one of the following settings:
RGB color mixing mode
CMY color mixing mode
3) Press
to confirm the selection or LEFT
to keep current settings.
CMY
Fixwheel
Shortcut
On
Fixed wheel short-cut
Used for optimizing color change time so that the disc turns in the direction that requires shorter movement.
1) Press
– the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
color change optimization.
3) Press
to confirm the selection, or LEFT
to keep current settings.
Off
Macro Color
Adjustment
Macro color adjustment
It lets you enable the overwriting of a “Macro Colour” with the Cyan,
Magenta, Yellow, CTO and Colour wheel channels.
Press
the current setting appears on the display.
1) Use the UP
and DOWN
keys to enable (On) or disable (Off)
the overwriting.
2) Press
to confirm the selection or LEFT
to keep the current setting.
Off
ALPHA SPOT HPE 1500
On
9
Continue
➔
Shutter
Shutter
On Error
SHUTTER
Shutter on error
Used for automatically closing the stop/strobe in the event of Pan/Tilt
position error.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
automatic stop/strobe closing in the event of Pan/Tilt position error.
3) Press
to confirm the selection, or LEFT
to keep current settings.
On
Off
Dimmer On
Shutter
On
Dimmer on Shutter
Enables automatic closing of the dimmer when the strobe is completely closed.
1) Press
– the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
the automatic closing of the dimmer.
3) Press
to confirm the selection or LEFT
to keep current settings.
Off
Auto-focus
Mode
AUTO-FOCUS MODE
It lets you select the “Auto-focus Mode” from the two available.
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
Limited Zoom Range: The “Autofocus” works only in the optical run
that was specifically designed for the projector in question.
Complete Zoom Range: The “Autofocus” also works in overrun
3) Press
to confirm the selection or LEFT
to keep the current setting.
Limited
Zoom Range
Complete
Zoom Range
MACRO EFFECTS
It lets you select the “Macro Effects” set up from the two available.
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
Macro
Effects
Macro group
size
Macro group size
It lets you set the number of projectors to be included in the macro mode
operation.
1) Press
2) Use the UP
, DOWN
, RIGHT keys to set the number of projectors
to be included in the “Macro Effect” operation.
3) Press
to confirm the selection or LEFT
to keep the current setting.
Macro fixture Id
It lets you attribute an ID address to the projector for the phase
displacement for the scene’s starting time in Macro mode.
1) Press
2) Use the UP
and DOWN
keys to select one of the following settings:
Fixed to X. (to assign to all the projectors to be included in the Macro
operation).
Auto by DMX Address: According to the DMX address, it automatically
detects the starting sequence of the scene in the Macro mode (to assign
to all the projectors to be included in the Macro operation).
3) Press
to confirm the selection or LEFT
to keep the current setting.
Macro fixture Id
Silent
Mode
SILENT MODE
It lets you select the “Silent Mode” from the two available.
1) Press
the current setting appears on the display.
2) Use the UP
and DOWN
keys to select one of the following settings:
Standard: Maximum speed and consequently maximum effects noise level.
Quiet: reduces the speed of some effects, thereby reducing their noise level.
3) Press
to confirm the selection or LEFT
to keep the current setting.
Standard
Quiet
ALPHA SPOT HPE 1500
10
POWER MODE
Allows you to select a Power Mode from the three available.
1) Press
- the current settings appear on the display.
2) Use the UP and DOWN keys to select one of the following settings:
- 1500-1200W Full fan speed: Lamp can change from full-power
(1500W) to half-power (1200W) using the LAMP CONTROL channel.
Fans always work at Full speed
- 1200W Low fan speed: Lamp constantly works in half-power mode
(1200W) while the Fan always works at Low speed. With LAMP
CONTROL channel you can only switch the lamp ON and OFF.
- 1500-1200W Auto fan speed: Lamp can change from full-power
(1500W) to half-power (1200W) using the LAMP CONTROL channel.
Automatically the fans switch from Full speed to Low speed respectively.
3) Press
to confirm the selection or LEFT
to keep current setting.
Power Mode
1500-1200
Full fan speed
1200
Low fan speed
1500-1200
Auto fan speed
On
DISPLAY
Used for automatically reduce brightness on the display after about 30
seconds in idle.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to enable (On) or disable (Off)
the decreasing of display brightness.
3) Press
to confirm the selection or LEFT
to keep current
settings.
Display
Off
Setting
Default
Preset
Reset To
Dafault
SETTING
Used to save 3 different settings of the items in the options menu and
relative submenus.
1) Press
- “Default preset” appears on the display.
2) Use the UP
and DOWN
keys to select one of the following
configurations:
- Default preset (*)
- User preset 1
- User preset 2
- User Preset 3
3) Press
- “Load preset X” appears on the display.
4) Use the UP
and DOWN
keys to select:
- Load preset X to recall a previously stored configuration.
- Save to preset X to store the current configuration.
a confirmation message (Are you sure?) appears on the display.
5) Select YES to confirm the selection or NO to keep the current setting
and return to the next higher level.
Go Back
User
Preset 1
Load
Preset 1
Save To
Preset 1
User
Preset 2
Load
Preset 2
Save To
Preset 2
User
Preset 3
Load
Preset 3
Save To
Preset 3
(*) DEFAULT PRESET
Used for restoring default values on all options menu items and relevant
submenus.
1) Press
, a confirmation message (Are you sure?) appears on the
display.
2) Select YES to confirm the selction or NO to keep current setting.
OPTION
DEFAULT
Lamp DMX
On
Invert Pan
Off
Invert Tilt
Off
Swap Pan-Tilt
Off
Encoder Pan-Tilt
On
Colour mixing
CMY
Fixed Wheel Shortcut
On
Macro Color Adjustment
On
Shutter on error
Off
Dimmer on Shutter
Off
Auto-focus mode
Limited zoom range
Silent mode
Standard
Power mode
1500-1200w full fan speed
Display
On
ALPHA SPOT HPE 1500
11
Continue
➔
INFORMATION MENU
Information
SYSTEM ERRORS
Shows a list of warnings and messages relevant to errors occurred since
the fixtures switching-on.
1) Pressing
you are allowed to reset the SYSTEM ERRORS list.
A confirmation message (Are you sure you want to clear error list ?)
appears on the display.
2) Select YES to reset the list or NO to go back.
System
Errors
Fixture
Hours
Total XXX
Partial XXX
FIXTURE HOURS
Used for displaying projector operating hours (total and partial).
- Hours total and partial appears on the display.
1) Press
Total counter
Counts the number of projector working life hours (from manufacture to date).
Partial counter
Counts the number of partial projector working life hours since the
last reset to date.
to reset partial projector working hours a confirmation
2) Press
message (Are you sure?) appears on the display.
3) Select YES to reset partial projectors counter or NO to keep the
current setting and return to the top menu level.
Reset...
Lamp
Hours
Total XXX
Partial XXX
LAMP HOURS
Used for displaying the lamp working hours (total and partial).
- Hours total and partial appears on the display.
1) Press
Total counter
Counts the number of projector working hours with the lamp on (from
manufacture to date).
Partial counter
Counts the number of lamp working hours since the last reset to date.
to reset partial lamp working hours, a confirmation message
2) Press
(Are you sure ?) appears on the display.
3) Select YES to reset partial counter or NO to keep the current setting and
return to the top menu level
Reset...
Lamp
Strikes
Total XXX
Partial XXX
LAMP STRIKES
Used for displaying the number of times the lamp was turned on (total and
partial).
- the number of times the lamp was turned on (total and
1) Press
partial) appears on the display.
Total counter
Counts the number of times the lamp was turned on (from manufacture
to date).
Partial counter
Counts the number of times the lamp was turned on since the last
reset to date.
to reset partial lamp strikes hours, a confirmation message
2) Press
(Are you sure ?) appears on the display.
3) Select YES to reset partial counter or NO to keep the current setting
and return to the top menu level
Reset...
System
Version
ALPHA SPOT HPE 1500
Board
CPU brd
com.dev
0: PT-3f
1: 8-Ch
2: 8-Ch
3: 8-Ch
Revis.
x.x.x
x.x
x.x
x.x
x.x
x.x.
SISTEM VERSION
Used for displaying the software and hardware version of each board
installed in the projector.
CPU brd (CPU board)
0: PT-3f (Pan / Tilt board)
1: 8-Ch (8 channel board)
2: 8-Ch (8 channel board)
3: 8-Ch (8 channel board)
Hw.rv.
x.x
x.x
x.x
x.x
x.x
12
Board
Diagnost.
Board
0:PT-3f
1:8-Ch
2:8-Ch
3:8-Ch
Status
Good
Good
Good
Good
BOARD DIAGNOSTIC
Used for displaying the status error of each board installed in the projector:
0: PT-3f (Pan / Tilt board)
1: 8-Ch (8 channel board)
2: 8-Ch (8 channel board)
3: 8-Ch (8 channel board)
Err%
0.00
0.00
0.00
0.00
DMX MONITOR
Used for displaying the projector DMX channel level in bit (Val) and in
percentage (Perc).
Dmx
Monitor
Fans
Monitor
Fan
Pwr.Sup
Ball.In.
Ball.Out
Eff.In
Eff.Out
Lamp
Lamp
Gobo
Board
FANS MONITOR
Used for displaying the speed of each fan installed in the projector:
Pwr.Sup (Power supply Fan)
Ball. IN (Ballast IN Fan)
Ball. Out (Ballast OUT Fan)
Eff.IN (Effects IN Fan)
Eff.OUT (Effects OUT Fan)
Lamp (Lamp Fan)
Lamp (Lamp Fan)
Gobo (Gobo Fan)
Board (Yoke Board Fan)
Speed (RPM)
XXXX
XXXX
XXXX
XXXX
XXXX
XXXX
XXXX
XXXX
XXXX
NETWORK PARAMS
Allows the "Network" parameters of the projector to be displayed or:
IP address: Internet Protocol address (two projectors must not have the
same IP address)
IP mask:
Mac address: Media Access Control: the projector’s Ethernet Address.
Network
params
MANUAL CONTROL
Manual
Control
On
LAMP
Used for turning lamp on and off from the projector control panel.
1) Press
- the current settings appear on the display (On or Off).
2) Use the UP
and DOWN
keys to turn the lamp on (On) or off (Off)
3) Press
to confirm the selection or LEFT
to keep current settings
and return to the top level.
Lamp
Off
No
RESET
Used for resetting the projector.
1) Press
to reset the projectors, a confirmation message (Are you sure ?)
appears on the display.
2) Select YES to starting reset the fixture or NO to keep the current setting
and return to the top menu level.
Reset
Yes
CHANNEL
Used for setting channel levels from the projector control panel.
1) Press
- the first channel appears on the display.
2) Use the UP
and DOWN
keys to select the required channel:
3) Press
and use the UP
and DOWN
keys to select the
required DMX level (value between 0 and 255).
4) Press LEFT
to return to the top menu level.
Channel
ALPHA SPOT HPE 1500
13
Continue
➔
TEST MENU
Test
AUTOTEST
Allows you to check the proper functioning of effects.
1) Press
.
2) Use the UP
and DOWN
keys to select the required test.
3) Press
to confirm the selection or LEFT
to return to the top
menu level.
Pan-Tilt
Colour
Beam
Gobo
All
Test sequence:
- Pan - Tilt effects (Pan & Tilt)
- Colour effects (CMY, colour wheel)
- Beam effects (Stopper-Strobe / Dimmer / Iris / Prism / Frost / Focus /
Zoom, Animation disk)
- Gobo effects (Fixed gobo / Rotating gobo)
- All effects
ADVANCED MENU
Advanced
Code
1234
To enable the "Advanced Menu" set up the "Access code" (1234) using the
UP , DOWN
, RIGHT
keys.
Press
- "Menu advanced" appears on the display
Upload
Firmware
Setup
Model
Transfer the firmware on all
the connected fixtures ?
Are you sure ?
Yes/No
UPLOAD FIRMWARE
Allows you to transfer the firmware from 1 fixture to all the connected fixtures.
1) Press
, a confirmation message appears on the display.
2) Select YES to start the firmware loading or NO to keep the current setting and return to the top menu level
Changing to a wrong model
may damage the fixture.
Are you sure ?
Yes/No
SETUP MODEL
Allows you to change the default model of projector.
1) Press
a confirmation message appears on the display.
2) Select YES to define the model of projector or NO to keep the current
setting and return to the top menu level.
CALIBRATION
Allows you to adjust effects from the control panel to obtain perfect uniformity between the projectors.
1) Press
- “channels” appears on the display.
2) Using the UP
and DOWN
keys, select the effect you wish to
regulate.
3) Press
and use the RIGHT
, UP
and DOWN
buttons to
make the adjustment by setting a value between 0 and 255.
4) Press
to confirm the selection or LEFT
to keep current settings and return to the top level.
Calibration
FACTORY DEFAULT
Allows you to restore default values of all channels (128).
1) Press
– a confirmation message appears on the display (Reset
calibration to factory default ?).
2) Select YES to reset calibration to factory default or NO to keep the
current setting and return to the top menu level.
ALPHA SPOT HPE 1500
14
MAINTENANCE
11
12
3
1
2
2
1
1/4 Turn
4
1
5
Locking and releasing Pan and Tilt movements - Refer to the instructions in the UNPACKING AND PREPARATION section.
Opening the head covers - Fig. 11.
Closing the head covers - Fig. 12.
ALPHA SPOT HPE 1500
15
1/4 Turn
13
14
1
1
2
Lamp change - Fig 14
Take the new lamp out of its package and insert in the fitting.
WARNING: do not touch the lamp’s envelope with bare hands.
Should this happen, clean the bulb with a cloth soaked in alcohol
and dry it with a clean, dry cloth.
2
15
Opening and closing lamp compartment - Fig. 13
16
Lamp regulation - Fig. 15
To centre the lamp, turn the three adjusting screws as shown in the figure.
Lower Side
1
2
Fan support plate opening and closing (Lower side) - Fig. 16
ALPHA SPOT HPE 1500
16
Continue
➔
17
Upper Side
1
2
Fan support plate opening and closing (Upper side) - Fig. 17
18
Black Side
Lower Side
2
Black Side
1
085908/001
085904/001
085912/001
085906/001
Replacing fixed gobos (ø 31.5 mm - max 25 mm image - thickness max 1 mm) - Fig. 18
IMPORTANT: Please contact CLAY PAKY before using customized gobos.
ALPHA SPOT HPE 1500
17
085907/001
085903/001
085911/001
085901/001
19
Lower Side
1
2
Bearing group replacement - Fig. 19
20
1
2
GOBO ROTATION 1
105115/801
105115/802
084632/001
GOBO ROTATION 2
084624/001
084631/001
GOBO
INDEX
084629/001
GOBO
INDEX
084630/001
084628/001
084633/001
084625/001
084626/001
084627/001
Replacing rotating gobos (ø 37.5 mm - max 25 mm image – thickness 1 mm) - Fig. 20
IMPORTANT: Please contact CLAY PAKY before using customized gobos.
ALPHA SPOT HPE 1500
18
Continue
➔
21
COATED GLASS GOBOS TYPE 1
COATED GLASS GOBOS TYPE 2
Coated side
towards lamp
Grey/Black side away
from lamp
Coated side
Uncoated
side
Uncoated side
Reflective side towards lamp
To determine which side of a godo is coated, hold an odject up to it. On the
uncoated side, there is a space between the object and its reflection.
Gobo orientation - Fig. 21
The pictures shown the correct gobos orientation.
22
Upper Side
Lower Side
Periodical cleaning - Fig. 22
To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The
frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of the
working environment (air humidity, presence of dust, salinity, etc.).
Use a soft cloth dampened with any detergent liquid for cleaning glass to remove the dirt from the reflectors, from the lenses and filters. It is recommended
that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations:
• General cleaning of internal parts.
• Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Clay Paky.
• General visual check of the internal components, cabling, mechanical parts, etc.
• Electrical, photometric and functional checks; eventual repairs.
ALPHA SPOT HPE 1500
19
23
4
3
Thermostat
5
Lower Side
2
6
1
Extraction of the effect modules: Preliminary operations - Fig. 23
ALPHA SPOT HPE 1500
20
Continue
➔
24
Lower Side
10
6
7
9
13
11
8
12
Upper Side
Upper Side
18
14
15
17
16
Extraction of the effect modules - Fig. 24
IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged.
Insertion of the effect modules: Repeat the operations indicated in Fig. 24 and 25 in reverse order
ALPHA SPOT HPE 1500
21
25
Upper Side
Upper Side
21
19
20
Upper Side
Upper Side
26
22
23
24
25
Extraction of the effect modules - Fig. 25
IMPORTANT: Grasp the modules using the support structure and not the details which could get damaged.
Insertion of the effect modules: Repeat the operations indicated in Fig. 24 and 25 in reverse order
ALPHA SPOT HPE 1500
22
TECHNICAL INFORMATION
IP20 protection rating
• Protected against the entry of solid bodies larger
than 12mm (0.47”).
• No protection against the entry of liquids.
Power supplies available
200-240V 50/60Hz
Input power
• 2000VA a 230V 50Hz.
Lamp
Discharge lamp.
• Type HTI 1500W/60/P50-L Lok-it Osram (L10102)
- Cap PGJ50
- Colour temperature 6000 K
- Luminous flux 135000 lm
- Average life 750 h
- Any working position
628
(24.72")
Motors
29 stepper motors, operating with microsteps,
totally microprocessor controlled.
Channels
Max 40 control channels.
843
(33.19")
Movable body
• Movement by means of two stepper motors, controlled by microprocessor.
• Automatic repositioning of PAN and TILT after
accidental movement not controlled by control
unit.
• Travel:
- PAN = 540°
- TILT = 252°
• Maximum speeds:
- PAN = 4.0 sec (360°)
- TILT = 3.2 sec (252°)
• Resolution:
- PAN = 2.11°
- PAN FINE = 0.008°
- TILT = 0.98°
- TILT FINE = 0.004°
500
(19.69")
Cooling
Forced ventilation with axial fans.
Working position
Functioning in any position.
Inputs
• DMX 512
232
(9.13")
Safety Devices
• Bipolar circuit breaker with thermal protection.
• Automatic break in power supply in case of
overheating or failed operation of cooling system.
Body
• Aluminium structure with die-cast plastic cover.
• Two side handles for transportation.
• Device locking PAN and TILT mechanisms for
transportation and maintenance.
Optical unit
• Elliptic reflector with high luminous efficiency
660
(25.98")
CE Marking
In conformity with the European Union Low Voltage
Directive 2006/95/CE and Electromagnetic compatibility Directive 2004/108/CE.
Weights
about 50.95 Kg (112lbs, 1oz).
480
(18.90")
488
(19.21")
CAUSE AND SOLUTION OF PROBLEMS
THE PROJECTOR WILL NOT SWITCH ON
ELECTRONICS NON-OPERATIONAL
PROBLEMS
DEFECTIVE PROJECTION
REDUCED LUMINOSITY
POSSIBLE CAUSES
No mains supply.
Lamp exhausted or defective.
Signal transmission cable faulty or disconnected.
Incorrect addressing.
Fault in the electronic circuits.
Lenses or reflector broken
Dust or grease deposited.
ALPHA SPOT HPE 1500
CHECKS AND REMEDIES
Check the power supply voltage.
Replace the lamp. (See instructions).
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).
23
CHANNEL FUNCTION
ALPHA SPOT HPE 1500
CHANNEL MODE
CHANNEL
STANDARD
VECTOR
1
CYAN
CYAN
2
MAGENTA
MAGENTA
3
YELLOW
YELLOW
4
C.T.O
C.T.O
5
COLOUR WHEEL
COLOUR WHEEL
6
MACRO COLOURS
MACRO COLOURS
7
STOP/STROBE
STOP/STROBE
8
DIMMER
DIMMER
9
DIMMER FINE
DIMMER FINE
10
IRIS
IRIS
11
ANIMATED STAR GOBO
ANIMATED STAR GOBO
12
STATIC GOBO CHANGE
STATIC GOBO CHANGE
13
ROTATING GOBO 1 CHANGE
ROTATING GOBO 1 CHANGE
14
GOBO 1 ROTATION
GOBO 1 ROTATION
15
GOBO 1 FINE
GOBO 1 FINE
16
ROTATING GOBO2 CHANGE
ROTATING GOBO2 CHANGE
17
GOBO2 ROTATION
GOBO2 ROTATION
18
GOBO2 FINE
GOBO2 FINE
19
ANIMATION DISK INSERTION
ANIMATION DISK INSERTION
20
ANIMATION DISK ROTATION
ANIMATION DISK ROTATION
21
ROTATING PRISM INSERTION
ROTATING PRISM INSERTION
22
PRISM ROTATION
PRISM ROTATION
23
FROST INSERTION
FROST INSERTION
24
FOCUS
FOCUS
25
FOCUS FINE
FOCUS FINE
26
ZOOM
ZOOM
27
AUTOFOCUS DISTANCE
AUTOFOCUS DISTANCE
28
AUTOFOCUS ADJUSTMENT
AUTOFOCUS ADJUSTMENT
29
MACRO EFFECTS
MACRO EFFECTS
30
PAN
PAN
31
PAN FINE
PAN FINE
32
TILT
TILT
33
TILT FINE
TILT FINE
34
FUNCTION
FUNCTION
35
RESET
RESET
36
LAMP ON/OFF (with Option "Lamp DMX" ON)
LAMP ON/OFF (with Option "Lamp DMX" ON)
37
PAN-TILT TIME
38
COLOUR TIME
39
BEAM TIME
40
GOBO TIME
Continue
ALPHA SPOT HPE 1500
24
➔
NOTE: On conclusion of resetting in case of absence of DMX signal, Pan & Tilt move to the "Home" position (Pan 50% - Tilt 50%) all the others channels stay at 0%.
• MACRO COLOURS - channel 6
• COLOUR MIXING - channel 1 - 2 - 3
Operation with option color mixing: RGB
CHANNEL 1
CYAN
CHANNEL 2 CHANNEL 3
MAGENTA
BIT
%
255
100
0
YELLOW
0.0
COLOR NAME
EFFECT
Unused Range
Half CT straw
Lighter blue
Glacier blue
Fuschia pink
Mallard green
Jade
3/4 CT Orange
3/4 CTB
Half minus green
Minus green
1/4 CTO
1/2 CTO
Full CT Orange
1/4 CTB
1/2 CTB
Full CTB
Alice Blue
Congo Blue
Dark Lavender
Chrome Orange
Lagoon blue
Deep Lavender
Liliac tint
Daylight Blue
Flame red
Bastard amber
Deep Orange
Pink
Pale rose
Pale Gold
Bright rose
Apricot
Bright Blue
Primary green
Light green
Pale green
Special Lavender
Pale Lavender
Deep golden amber
Golden amber
Medium blue
Marine blue
Bright pink
Mauve
Fern Green
Leaf green
Deep Blue
Dark blue
Light blue
Steel blue
Medium blue green
Peacock blue
Dark pink
Light Salmon
English rose
Light rose
COLOUR INSERTED
IMPORTANT: The lamp dim to half power 1 second after all the 3 channels stay at 0%
level. The lamp goes back to full power when the channels level is put higher than 0%.
Operation with option color mixing: CMY
CHANNEL 1 CHANNEL 2 CHANNEL 3
CYAN
MAGENTA
BIT
%
255
100
COLOUR INSERTED
0
0.0
COLOUR EXCLUDED
YELLOW
EFFECT
IMPORTANT: The lamp dim to half power 1 second after all the 3 channels
stay at 100% level. The lamp goes back to full power when the channels level
is put lower than 100%.
• C.T.O. - channel 4
CHANNEL 4
CTO
BIT
%
EFFECT
255
100
FILTER INSERTED
0
0.0
FILTER EXCLUDED
Primary red
Orange
Deep amber
Straw
Light amber
Yellow
Spring yellow
Dark Yellow Green
Lime green
Just Blue
Tokyo Blue
Sky blue
Pale blue
Lavender
Bright Red
Med Yellow
Med bastard amber
Random Macro Color
(only for Macro effects)
Unused Range
• COLOUR WHEEL - channel 5
ALPHA SPOT HPE 1500
BIT
%
148-255
146-147
144-145
142-143
140-141
138-139
136-137
134-135
132-133
130-131
128-129
126-127
124-125
122-123
120-121
118-119
116-117
114-115
112-113
110-111
108-109
106-107
104-105
102-103
100-101
98-99
96-97
94-95
92-93
90-91
88-89
86-87
84-85
82-83
80-81
78-79
76-77
74-75
72-73
70-71
68-69
66-67
64-65
62-63
60-61
58-59
56-57
54-55
52-53
50-51
48-49
46-47
44-45
42-43
40-41
38-39
36-37
58,0-100
57,0-57,5
56,2-56,7
55,5-56,0
54,7-55,0
54,0-54,2
53,2-53,7
52,5-53,0
51,7-52,0
51,0-51,2
50,0-50,5
49,5-49,7
48,7-49,0
48,0-48,2
47,0-47,5
46,2-46,7
45,5-46,0
44,7-45,0
44,0-44,2
43,2-43,7
42,5-43,0
41,7-42,0
41,0-41,2
40,0-40,5
39,0-39,5
38,2-38,7
37,5-38,0
36,7-37,0
36,0-36,2
35,0-35,5
34,2-34,7
33,7-34,0
33,0-33,2
32,0-32,5
31,2-31,7
30,5-31,0
29,7-30,0
29,0-29,5
28,2-28,7
27,5-28,0
26,7-27,0
26,0-26,2
25,0-25,5
24,2-24,7
23,7-24,0
23,0-23,2
22,0-22,5
21,2-21,7
20,5-21,0
19,5-20,0
18,7-19,0
18,0-18,2
17,0-17,5
16,2-16,7
15,5-16,0
14,7-15,0
14,0-14,2
34-35
32-33
30-31
28-29
26-27
24-25
22-23
20-21
18-19
16-17
14-15
12-13
10-11
8-9
6-7
4-5
2-3
1
0,00
13,2-13,7
12,5-13,0
11,7-12,0
11,0-11,2
10,0-10,5
9,5-9,7
8,7-9,0
8,0-8,2
7,0-7,5
6,2-6,7
5,5-6,0
4,7-5,0
4,0-4,2
3,2-3,7
2,5-3,0
1,7-2,0
1,0-1,2
0,5
0,0
COLOUR EXCLUDED
BIT
%
255
100
FAST ROTATION 160 rpm
EFFECT
128
50.0
SLOW ROTATION 0.2rpm
117
46.0
BLUE
97
38.0
ORANGE
77
30.0
AQUAMARINE
58
23.0
GREEN
39
15.0
CTO 3200
20
8.0
RED
0
0.0
WHITE
25
ROSCO LEE
CODE CODE
442
442
353
353
352
352
345
345
325
325
323
323
285
285
281
281
248
248
247
247
206
206
205
205
204
204
203
203
202
202
201
201
197
197
181
181
180
180
179
179
172
172
170
170
169
169
165
165
164
164
162
162
158
158
157
157
154
154
152
152
148
148
147
147
141
141
139
139
121
121
138
138
137
137
136
136
135
135
134
134
132
132
131
131
128
128
126
126
122
122
121
121
120
120
119
119
118
118
117
117
116
116
115
115
111
111
109
109
108
108
107
107
106
105
104
103
102
101
100
090
088
079
071
068
063
058
026
010
004
-
182
105
104
103
102
101
100
090
088
079
071
068
063
058
026
010
004
-
CYAN
BIT
0
226
220
109
255
127
0
85
60
60
62
25
0
75
85
94
236
251
195
0
224
100
41
210
0
0
0
0
0
0
0
0
182
0
0
105
97
73
0
0
255
60
0
0
173
136
255
255
245
167
189
136
0
50
0
0
0
0
0
58
0
0
80
255
118
255
255
245
122
165
0
48
0
-
MAGENTA YELLOW
BIT
BIT
0
34
0
149
0
129
186
77
0
0
0
162
36
61
79
87
19
86
71
86
71
123
26
45
44
58
54
91
71
84
79
80
51
0
241
0
170
0
98
255
0
121
129
77
59
39
73
105
255
227
26
0
148
255
159
0
48
0
60
98
255
0
81
55
0
99
0
0
0
255
0
179
105
72
102
44
255
255
142
234
152
127
0
106
255
0
255
0
0
235
0
241
229
58
161
0
0
145
0
141
0
157
0
128
139
0
121
58
62
0
95
0
0
182
26
17
0
0
0
0
0
77
255
77
0
186
255
0
62
-
0
255
199
104
171
255
227
255
241
0
0
64
112
77
0
239
78
-
CTO
BIT
190
138
138
120
236
0
217
54
75
75
122
131
234
109
89
0
205
255
160
255
40
120
120
88
255
199
255
255
189
138
255
255
92
231
0
100
90
120
255
110
0
73
197
255
89
64
128
0
138
165
91
91
220
230
247
220
WHEEL
BIT
0
0
0
0
58
77
0
0
39
39
0
0
0
0
0
0
0
0
0
0
79
0
0
0
97
0
0
0
0
0
0
0
77
58
77
0
0
0
0
0
77
77
0
74
0
0
77
77
0
0
77
77
0
0
0
0
0
76
223
176
193
149
157
204
124
204
180
173
127
0
255
115
159
-
20
0
0
0
0
0
0
0
0
0
77
0
0
0
21
0
0
-
• ANIMATED STAR GOBO – channel 11
*With the "Animated star gobo" on this bit/percentual, all "Macro effects" that include
an Iris scene, use the "Animated Star gobo" instead the "Iris"
BIT
%
EFFECT
252 - 255
239 - 251
226 - 238
213 - 225
208 - 212
207
98.7 - 100
93.7 - 98.2
88.7 - 93.2
83.7 - 88.2
81.7 - 83.2
81.2
OPEN
RANDOM FAST STROBE
RANDOM MEDIUM STROBE
RANDOM SLOW STROBE
OPEN
FAST PULSATION
MACRO
MACRO
• STOP / STROBE - channel 7
108
104 - 107
103
42.5
41.0 - 42.0
40.5
SLOW PULSATION
OPEN
FAST STROBE (12 flash/sec)
4
0-3
1.7
0.0 - 1.2
SLOW STROBE (1 flash/sec)
CLOSED
EFFECT
MAXIMUM APERTURE
FAST PULSATION, FAST CLOSING
212
211
83.2
83
SLOW PULSATION, FAST CLOSING
FAST PULSATION, FAST OPENING
172
171
67.5
67
SLOW PULSATION, FAST OPENING
FAST PULSATION
0
SLOW PULSATION
51.7
50.0 - 51.2 MAXIMUM APERTURE
0.0
MINIMUM APERTURE
• STATIC GOBO CHANGE - channel 12
• DIMMER - channel 8
%
255
100
EFFECT
DIMMER OPEN
MACRO
BIT
0
0.0
DIMMER CLOSED
The lamp is linearly dimmed from full power to half power electronicaly and
mechanically from half power to off.
• DIMMER FINE - channel 9
BIT
%
255
100
0
EFFECT
0.0
• IRIS - channel 10
MACRO
%
98.7 - 100
98.2
132
128 - 131
IMPORTANT: The lamp dim to half power 1 second after the channel stay at
0% level. The lamp goes back to full power when the channel level is put
higher than 0%.
BIT
%
EFFECT
252 - 255
251
98.7 - 100
98.2
MAXIMUM APERTURE
FAST PULSATION, FAST CLOSING
212
211
83.2
83
SLOW PULSATION, FAST CLOSING
FAST PULSATION, FAST OPENING
172
171
67.5
67
SLOW PULSATION, FAST OPENING
FAST PULSATION
132
128 - 131
0
ALPHA SPOT HPE 1500
BIT
252 - 255
251
SLOW PULSATION
51.7
50.0 - 51.2 MAXIMUM APERTURE
0.0
MINIMUM APERTURE
26
BIT
%
EFFECT
255
100
GOBO 8 SHAKE, FAST SPEED
244
243
95.5
95.0
GOBO 8 SHAKE, SLOW SPEED
GOBO 7 SHAKE, FAST SPEED
232
231
91.0
90.5
GOBO 7 SHAKE, SLOW SPEED
GOBO 6 SHAKE, FAST SPEED
220
219
86.2
86.0
GOBO 6 SHAKE, SLOW SPEED
GOBO 5 SHAKE, FAST SPEED
208
207
81.7
81.2
GOBO 5 SHAKE, SLOW SPEED
GOBO 4 SHAKE, FAST SPEED
196
195
76.7
76.2
GOBO 4 SHAKE, SLOW SPEED
GOBO 3 SHAKE, FAST SPEED
184
183
72.0
71.7
GOBO 3 SHAKE, SLOW SPEED
GOBO 2 SHAKE, FAST SPEED
172
171
67.5
67.0
GOBO 2 SHAKE, SLOW SPEED
GOBO 1 SHAKE, FAST SPEED
160
159
63.0
62.5
GOBO 1 SHAKE, SLOW SPEED
FAST ROTATION (100 rpm)
118
114 - 117
113
46.2
44.7 - 46.0
44.2
SLOW ROTATION (5 rpm)
STOP
SLOW ROTATION (5 rpm)
FAST ROTATION (100 rpm)
72
28.2
64 - 71
25.0 - 28.0
GOBO 8
56 - 63
22.0 - 24.7
GOBO 7
48 - 55
18.7 - 21.7
GOBO 6
40 - 47
15.5 - 18.2
GOBO 5
32 - 39
12.5 - 15.0
GOBO 4
24 - 31
9.5 - 12.0
GOBO 3
16 - 23
6.2 - 9.0
GOBO 2
8 - 15
3.2 - 6.0
GOBO 1
0-7
0 - 3.0
WHITE
• ROTATING GOBO 2 CHANGE - channel 16
BIT
%
EFFECT
BIT
%
EFFECT
255
100
GOBO 6 SHAKE, FAST SPEED
255
100
GOBO 6 SHAKE, FAST SPEED
235
234
92.0
91.7
GOBO 6 SHAKE, SLOW SPEED
GOBO 5 SHAKE, FAST SPEED
235
234
92.0
91.7
GOBO 6 SHAKE, SLOW SPEED
GOBO 5 SHAKE, FAST SPEED
214
213
84.0
83.7
GOBO 5 SHAKE, SLOW SPEED
GOBO 4 SHAKE, FAST SPEED
214
213
84.0
83.7
GOBO 5 SHAKE, SLOW SPEED
GOBO 4 SHAKE, FAST SPEED
193
192
75.5
75.0
GOBO 4 SHAKE, SLOW SPEED
GOBO 3 SHAKE, FAST SPEED
193
192
75.5
75.0
GOBO 4 SHAKE, SLOW SPEED
GOBO 3 SHAKE, FAST SPEED
172
171
67.5
67.0
GOBO 3 SHAKE, SLOW SPEED
GOBO 2 SHAKE, FAST SPEED
172
171
67.5
67.0
GOBO 3 SHAKE, SLOW SPEED
GOBO 2 SHAKE, FAST SPEED
151
150
59.0
58.7
GOBO 2 SHAKE, SLOW SPEED
GOBO 1 SHAKE, FAST SPEED
151
150
59.0
58.7
GOBO 2 SHAKE, SLOW SPEED
GOBO 1 SHAKE, FAST SPEED
130
112-129
51.0
44.0-50.5
GOBO 1 SHAKE, SLOW SPEED
GOBO 6
130
112-129
51.0
44.0-50.5
GOBO 1 SHAKE, SLOW SPEED
GOBO 6
93-111
36.2-43.7
GOBO 5
93-111
36.2-43.7
GOBO 5
75-92
29.5-36.0
GOBO 4
75-92
29.5-36.0
GOBO 4
56-74
22.0-29.0
GOBO 3
56-74
22.0-29.0
GOBO 3
38-55
14.7-21.7
GOBO 2
38-55
14.7-21.7
GOBO 2
19-37
7.5-14.2
GOBO 1
19-37
7.5-14.2
GOBO 1
0-18
0-7.0
WHITE
0-18
0-7.0
WHITE
MACRO
MACRO
• ROTATING GOBO 1 CHANGE - channel 13
• GOBO 1 ROTATION - channel 14
• GOBO 2 ROTATION - channel 17
BIT
%
EFFECT
BIT
%
EFFECT
255
100
FAST ROTATION (150 rpm)
255
100
FAST ROTATION (150 rpm)
193
191 - 192
190
STOP
128
127
540°
360°
0°
SLOW ROTATION (2,2 rph)
75.5
74.7 - 75.0 STOP
SLOW ROTATION (2,2 rph)
74.2
50.0
49.7
193
191 - 192
190
STOP
FAST ROTATION (150 rpm)
540° POSITION
105
41.7
450° POSITION
84
33.0
360° POSITION
63
24.7
270° POSITION
42
16.2
180° POSITION
21
8.2
90° POSITION
0
0.0
0° POSITION
540°
360°
0°
• GOBO 1 FINE - channel 15
SLOW ROTATION (2,2 rph)
75.5
74.7 - 75.0 STOP
SLOW ROTATION (2,2 rph)
74.2
128
127
50.0
49.7
FAST ROTATION (150 rpm)
540° POSITION
105
41.7
450° POSITION
84
33.0
360° POSITION
63
24.7
270° POSITION
42
16.2
180° POSITION
21
8.2
90° POSITION
0
0.0
0° POSITION
• GOBO 2 FINE - channel 18
BIT
%
BIT
%
255
100
255
100
127
50.0
127
50.0
0
0.0
0
0.0
Continue
ALPHA SPOT HPE 1500
27
➔
• ANIMATION DISK INSERTION - channel 19
• FROST - channel 23
BIT
%
EFFECT
255
100
DISK INSERTED
0
0.0
DISK EXCLUDED
• ANIMATION DISK ROTATION - channel 20
BIT
%
255
100
FROST INSERTED
EFFECT
0
0.0
FROST EXCLUDED
• FOCUS - channel 24
BIT
%
EFFECT
BIT
%
255
100
FAST ROTATION (120 rpm)
255
100
NEAR
131
125 - 130
124
51.2
49.0 - 51.0
48.7
SLOW ROTATION (4,4 rph)
STOP
SLOW ROTATION (4,4 rph)
0
0.0
FAST ROTATION (120 rpm)
0
0.0
DISTANT
• PRISM INSERTION - channel 21
EFFECT
• FOCUS FINE -channel 25
BIT
%
255
100
EFFECT
BIT
%
255
100
NEAR
EFFECT
0
0.0
DISTANT
PRISM INSERTED
128
127
50.0
49.7
PRISM EXCLUDED
0
0.0
• ZOOM - channel: 26
• PRISM ROTATION - channel 22
BIT
%
EFFECT
BIT
%
255
100
FAST ROTATION (120 rpm)
255
100
NARROW BEAM
EFFECT
0
0.0
WIDE BEAM
193
75.5
SLOW ROTATION (3 rph)
191 - 192 74.7 - 75.0 STOP
190
74.2
SLOW ROTATION (3 rph)
STOP
540°
360°
0°
ALPHA SPOT HPE 1500
128
127
50.0
49.7
FAST ROTATION (120 rpm)
POSITION 540°
105
41.7
POSITION 450°
84
33.0
POSITION 360°
63
24.7
POSITION 270°
42
16.2
POSITION 180°
21
8.2
POSITION 90°
0
0.0
POSITION 0°
28
• AUTOFOCUS DISTANCE - channel 27
BIT
%
255
100
EFFECT
100 METRES
128
50.0
50 METRES
102
40.0
40 METRES
77
30.0
30 METRES
51
20.0
20 METRES
26
10.0
10 METRES
7
3.0
3 METRES
0-6
0.0-2.5
AUTOFOCUS priority:
1) Rotating Gobo 2
2) Static Gobo
3) Rotating Gobo 1
4) Animated Star Gobo
5) Iris
• PAN - channel 30
Operation with option InvertPan Off
(Tilt conventionally represented at 14% and option Invert Tilt
100
0
0.0
Operation with option InvertPan On
(Tilt conventionally represented at 14% and option Invert Tilt
BIT
%
255
100
128
50.0
0
0.0
EFFECT
FOCUS FINE
BIT
%
255
100
0
0.0
FOCUS FINE
• MACRO EFFECTS - channel 29
ALPHA SPOT HPE 1500
%
255
AUTOFOCUS OFF
• AUTOFOCUS ADJUSTMENT - channel 28
• PAN FINE - channel 31
Operation with option InvertPan Off
(Tilt conventionally represented at 14% and option Invert Tilt
BIT
%
232-255
91,0-100
STAND BY BLACK
220-231
86,2-90,5
RANDOM MACRO 8
208-219
81,7-86,0
RANDOM MACRO 7
196-207
76,7-81,2
RANDOM MACRO 6
184-195
72,0-76,2
RANDOM MACRO 5
172-183
67,5-71,7
RANDOM MACRO 4
160-171
63,0-67,0
RANDOM MACRO 3
148-159
58,0-62,5
RANDOM MACRO 2
Off)
Off)
EFFECT
136-147
53,2-57,5
RANDOM MACRO 1
112-135
44,0-53,0
STAND BY BLACK
100-111
39,0-43,7
MACRO 8
88-99
34,2-38,7
MACRO 7
76-87
29,7-34,0
MACRO 6
64-75
25,0-29,5
MACRO 5
52-63
20,5-24,7
MACRO 4
40-51
15,5-20,0
MACRO 3
28-39
11,0-15,0
16-27
6,2-10,5
MACRO 1
12-15
4,7-6,0
STAND BY BLACK
8-11
3,2-4,2
STAND BY
0,0-3,0
MACRO OFF
0-7
BIT
Off)
BIT
%
255
100
0
0.0
Operation with option InvertPan On
(Tilt conventionally represented at 14% and option Invert Tilt
BIT
%
255
100
0
0.0
MACRO 2
29
Off)
• TILT - channel 32
Operation with option Invert Tilt Off
(Pan conventionally represented at 0% and option Invert Pan
BIT
%
255
100
• FUNCTION - channel: 34
Off)
BIT
%
255
100
EFFECT
UNUSED RANGE
SE
L
TX
D MX
S
E
63
128
50.0
24.7
51-62
20.0-24.2 LINEAR (Default)
38-50
14.7-19.5 CONVENTIONAL
DIMMER CURVE
FUNCTION
SEL
TX
DMX
S
E
0
TX
DMX
E
Operation with option Invert Tilt On
(Pan conventionally represented at 0% and option Invert Pan
BIT
%
255
100
9.7-14.2 NORMAL
12-24
4.7-9.5
FAST (Default)
0-11
0.0-4.2
UNUSED RANGE
PAN-TILT
FUNCTION
The functions are actived passing through unused range and staying 5 seconds in
necessary level.
0.0
SEL
S
25-37
• RESET - channel: 35
Off)
BIT
%
EFFECT
255
100
COMPLETE RESET
Complete reset is activated passing
throug the unused range and staying
5 seconds in complete reset levels.
SEL
TX
DMX
S
E
128
127
128
COMPLETE RESET
PAN / TILT RESET
Pan / Tilt reset is activated passing
throug the unused range and staying
5 seconds in Pan / Tilt reset levels.
50.0
30.0
29.7
77
76
S EL
TX
DMX
S
50.0
49.7
E
PAN / TILT RESET
EFFECTS RESET
Effects reset is activated passing
throug the unused range and staying
5 seconds in Effects reset levels.
26
25
10.0
9.7
0
0.0
EFFECTS RESET
UNUSED RANGE
0
0.0
SEL
TX
DMX
S
E
• TILT FINE - channel 33
Operation with option Invert Tilt Off
(Pan conventionally represented at 0% and option Invert Pan
• LAMP CONTROL (only with option LAMP DMX On) - channel: 36
Off)
IMPORTANT: Alpha Spot HPE 1500 is not provided with hot restrike igniter
BIT
%
BIT
%
EFFECT
255
100
255
100
LAMP ON (1500 W)
ON
Lamp ignition after 5 s
in full power levels.
Immediate transition
from half to full power.
SE
L
TX
DMX
S
E
ON
ON
180
179
70.5
70.0
LAMP ON (1500 W)
LAMP ON (1200 W)
Immediate transition
from full to half power.
Lamp ignition not allowed
in half power.
ON
OFF
101
100
39.5
39.0
LAMP ON (1200 W)
LAMP OFF
Lamp switch off passing
throug the unused
range and staying 5 s in
Lamp OFF levels.
OFF
0
SEL
0.0
TX
DMX
S
E
Operation with option Invert Tilt On
(Pan conventionally represented at 0% and option Invert Pan
BIT
%
255
100
0
0.0
Off)
SEL
TX
DMX
S
E
S
E
SEL
TX
DMX
ALPHA SPOT HPE 1500
30
26
25
10.0
9.7
LAMP OFF
0
0.0
UNUSED RANGE
TIMING CHANNELS
Timing Channel
Channel function
37
Pan - Tilt time
Pan – Tilt – Pan Fine – Tilt Fine
38
Colour time
Cyan - Magenta - Yellow – C.T.O. – Color wheel
39
Beam time
Dimmer - Iris -Focus effects movment - Focus - Zoom - Frost – Rotating Prism change – Frost insertion
40
Gobo time
Gobo Fix - Rotating Gobo 1/2 change – Animation Disk insertion
TIME TABLE
BIT
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Seconds
Full
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
3.6
3.8
4
4.2
4.4
4.6
4.8
5
5.2
5.4
5.6
5.8
6
6.2
6.4
6.6
6.8
7
7.2
7.4
7.6
7.8
8
8.2
8.4
ALPHA SPOT HPE 1500
BIT
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
Seconds
8.6
8.8
9
9.2
9.4
9.6
9.8
10
10.2
10.4
10.6
11
12
13
14
15
16
17
18
19
20
21
22
23
BIT
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
Seconds
BIT
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
31
Seconds
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
BIT
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
Seconds
58
59
60
65
70
75
80
85
90
95
100
110
120
130
140
150
BIT
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
160
Seconds
170
180
190
200
210
220
230
240
250
260
270
280
290
300
310
Follow cue
Data
www.gfstudio.com
Cod. 099105 - EN
Rev.0 10/10
CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.it

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement