Miele DA 5100 D EXT Technical data

Operating and installation instructions
Cooker hoods
DA 5100 D
DA 5100 D U
DA 5100 D EXT
To avoid the risk of accidents
or damage to the appliance
it is essential to read these
instructions before it is installed
and used for the first time.
en - GB
M.-Nr. 09 202 760
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Modes of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Miele|home . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Con|ctivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To switch the fan on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
To select a power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Intensive setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Run-on option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
To switch the fan off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
To switch the lighting on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Dimming the lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
To switch the lighting off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Filter operating hours counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Resetting the operating hours counter for the grease filter . . . . . . . . . . . . . . . 18
Resetting the operating hours counter for the charcoal filter . . . . . . . . . . . . . 20
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Grease filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Fitting and replacing the charcoal filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Changing a halogen lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Safety distance between hob and cooker hood. . . . . . . . . . . . . . . . . . . . . . . . 29
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Assembly parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2
Contents
Operation with DSM 400 control module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Potential free connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Connection to a light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Connection for air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Condensate trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Silencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3
Caring for the environment
Disposal of the packing material
Disposal of your old appliance
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
Packaging e.g. cling film, polystyrene
and plastic wrappings must be kept out
of the reach of babies and young
children. Danger of suffocation!
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
4
Warning and Safety instructions
This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal injury
and damage to property.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time.
They contain important information
on safety, installation, use and
maintenance.
Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.
Correct application
~ This appliance is intended for use in
domestic households and in similar
working and residential environments
such as:
– Shops
– Offices and showrooms
and by residents in establishments
such as:
– Hostels and guest houses.
~ It must only be used as a domestic
appliance to extract vapours and
remove odours from cooking.
~ The cooker hood is not intended for
outdoor use.
Any other usage is not supported by
the manufacturer and could be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation.
~ This appliance is not intended for
use by people with reduced physical,
sensory or mental capabilities, or lack
of experience or knowledge, unless
they are supervised whilst using it or
have been shown how to use it
correctly by a person responsible for
their safety.
Safety with children
~ This appliance is only intended for
use by adults who have read these
instructions.
~ This appliance is not a toy! To
prevent the risk of injury do not let
children play with the appliance or its
controls.
~ Children under 8 years of age must
be kept away from the cooker hood
unless they are constantly supervised.
~ Children 8 years and older may use
the cooker hood only if they have been
shown how to use it in a safe way and
understand the hazards involved.
~ Please be aware that on cooker
hoods with halogen lighting, the lamps
will get very hot during use and remain
hot for some time after switching off. To
safeguard against burning, keep
children well away from the lamps at all
times.
5
Warning and Safety instructions
Technical safety
~ Before installation, check the cooker
hood for visible signs of damage. Do
not install and use a damaged
appliance. It could be dangerous.
~ Before connecting the appliance to
the mains supply, make sure that the
voltage and frequency details given on
the data plate correspond with the
household electricity supply, otherwise
the appliance could be damaged.
Consult a qualified electrician if in any
doubt.
~ The electrical safety of this
appliance can only be guaranteed if it
is correctly earthed. It is most important
that this basic safety requirement is
observed and regularly tested and
where there is any doubt, the
household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
~ For safety reasons, this appliance
may only be used when it has been
fully installed.
~ Only open the housing as described
in the instructions given in the
installation sheet and in the Cleaning
and care section of this booklet. Under
no circumstances should any other
parts of the housing be opened.
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user, and can
cause operational faults.
6
~ Installation, maintenance and
repairs may only be carried out by a
service technician authorised by the
manufacturer in strict accordance with
current national and local safety
regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
~ Faulty components must only be
replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
~ During installation, maintenance and
repair work, the appliance must be
disconnected from the mains electricity
supply.
Warning and Safety instructions
~ Do not connect the appliance to the
mains electricity supply by a
multi-socket adapter or an extension
lead. These do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
Using at the same time as other
heating appliances that depend on
the air from the room
Warning - danger of toxic fumes
~ For appliances with an external fan
motor (...EXT models) the connection of
the two units must be made using the
connection cable and the plug
connectors.
These models may only be combined
with a Miele external motor.
~ This appliance must not be used in
a non-stationary location (e.g. on a
ship).
~ In areas which may be subject to
infestation by cockroaches or other
vermin, pay particular attention to
keeping the appliance and its
surroundings in a clean condition at all
times. Any damage which may be
caused by cockroaches or other vermin
will not be covered by the guarantee.
~ Great care should be taken when
using the cooker hood at the same time
and in the same room or area of the
house as another heating appliance
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas hobs, cookers or ovens which draw
air in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
When used in extraction mode, with or
without an external motor fitted, the
appliance draws air in from the room in
which it is installed and from
neighbouring rooms.
If there is insufficient air, an
underpressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.
Harmful gases could be drawn out of
the chimney or extraction ducting back
into the room, with potentially fatal
consequences.
7
Warning and Safety instructions
In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the cooker
hood and the heating appliance are in
operation simultaneously, an
underpressure in the room of 0.04 mbar
(4 pa) is the maximum permissible.
Ventilation can be maintained by air
inlets which cannot be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the cooker hood can
only be switched on when the heating
appliance is switched off or vice versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.
,The overall ventilation condition
of the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder or, for gas, a
qualified gas fitter (GasSafe
registered in the UK) or electrician
must be sought.
If the hood is being operated in
recirculation mode, the above
restrictions do not apply.
8
Warning and Safety instructions
Correct use
~ Never use an open flame beneath
the cooker hood. To avoid the danger
of fire, do not flambé or grill over an
open flame.
When switched on, the cooker hood
could draw flames into the filter. Fat
particles drawn into the cooker hood
present a fire hazard.
~ When using the cooker hood over a
gas hob, ensure that any burners in use
are always covered by a pan. Switch
the cooking zone off when a pan is
removed, even for a short time.
Regulate the flame so that it does not
burn up the sides of the pan.
Do not allow the pans to overheat
excessively (e.g. when using a wok).
The cooker hood can become
damaged when exposed to excessive
heat.
~ Do not use the cooker hood without
the filters in place. This way you will
avoid the risk of grease and dirt getting
into the appliance and hindering its
smooth operation.
~ The filters should be regularly
cleaned or changed as appropriate.
Saturated filters are a fire hazard. See
"Cleaning and care".
~ The cooker hood can get very hot
during cooking due to heat rising from
the hob.
Do not touch the housing or the grease
filters until the cooker hood has cooled
down.
~ Do not use a steam-cleaner to clean
this appliance. Steam could reach the
electrical components and cause a
short circuit.
~ Always switch the cooker hood on
when using the hob, otherwise
condensation may collect in the hood,
which could cause corrosion.
~ When cooking with oil or fat, chip
pans and deep fat fryers etc, do not
leave the pans unattended. Never leave
an open grill unattended when grilling.
Overheated oil and fat can ignite and
could set the cooker hood on fire.
9
Warning and Safety instructions
Correct installation
Accessories
~ Refer to the cooker or hob
manufacturer's instructions as to
whether a cooker hood may be
operated above the cooker/hob.
~ Only use genuine Miele original
~ The minimum safety distances
between the top of the cooker or hob
and the bottom of the cooker hood
given in the "Appliance dimensions"
section of this booklet must be
maintained, unless the hob
manufacturer states that a greater
safety distance is required.
If more than one cooking appliance is
fitted beneath the cooker hood, and
they have different minimum safety
distances to the cooker hood, select
the greater distance.
~ Safety regulations prohibit the fitting
of a cooker hood over solid fuel stoves.
~ All ducting, pipework and fittings
must be of non-flammable material.
These can be obtained from the Miele
Spare Parts department or from
builders' merchants.
~ The appliance must not be
connected to a chimney or vent flue
which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
~ If exhaust air is to be extracted into
a chimney or ventilation duct no longer
used for other purposes, seek
professional advice.
10
spare parts and accessories with this
appliance. Using spare parts or
accessories from other manufacturers
will invalidate the guarantee, and Miele
cannot accept liability.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
Modes of operation
The cooker hood works with
. . . air extraction:
. . . air recirculation:
(...U models only)
(excluding ...U models)
The air is drawn in, cleaned by the
grease filter and then directed outside.
The cooker hood is fitted with a
non-return flap, which is closed when
the cooker hood is switched off. No
exchange of room air and outside air
can take place. When the cooker hood
is switched on, the non-return flap
opens for the cooking vapours to be
blown directly outside.
The air is drawn in and cleaned first by
the grease filter and then by a charcoal
filter. The cleaned air is then
recirculated back into the kitchen
through grilles in the top of the cooker
hood tower.
Before using the cooker hood in
recirculation mode, ensure that the
charcoal filter is in place. See
"Cleaning and care".
. . . an external motor:
(...EXT models only)
...EXT models are designed to be
connected to an external motor located
outside the room.
The external motor is connected to the
cooker hood by means of a control
cable and is operated by the controls
on the cooker hood.
11
Guide to the appliance
12
Guide to the appliance
a Cover plate
m Operating hours control
b Tower
The indicator lamp for the operating
hours control lights up red when the
grease filter needs to be cleaned.
c Controls
d Hob lighting
e Recirculation grille
(...U models only)
f Canopy
g Charcoal filter
Optional accessory for ...U models only
h Grease filter
i Hob lighting control
This control switches the lighting on
and off, and is also a dimmer switch.
j On/Off control for the fan
Additional feature of the DA 5100 U:
The indicator lamp lights up blue when
the charcoal filter used in recirculation
mode needs to be replaced. For this to
happen, the operating hours counter
needs to be activated before the
appliance is used for the first time.
The control is used to reset the
appropriate operating hours counter
each time the grease filter is cleaned or
the charcoal filter has been changed
(see "Cleaning and care").
It can also be used to check and alter
the operating hours counter.
k Controls to select the fan power
level
l Control for the run-on option
The fan can be set to switch off
automatically after either 5 or 15
minutes.
For further details about the functions
of the appliance, see "Use".
13
Miele|home
Con|ctivity
– When the hob is switched on the
cooker hood hob lighting also comes
on and then after a short time the fan
switches on.
– During cooking the cooker hood
automatically sets its power level
according to the number of cooking
zones in operation and their power
levels.
– After switching the hob off the fan
and the hob lighting will switch off
automatically after a period of time.
This cooker hood is communication
enabled.
Communication module XKM 2000 DA
a, available as an optional extra,
enables the operation of the cooker
hood to be automatically controlled by
the operating status of a Miele electric
hob with onset controls.
For communication to take place, the
hob must be fitted with the appropriate
communication module b.
The hob transmits information about its
operating status to the cooker hood via
the household power supply
(Powerline) c.
14
For detailed information about this
function please read the separate
instruction booklet supplied with the
XKM 2000 DA communication module.
The communication module is fitted to
the cooker hood in the area of the
motor and is connected to the controls
of the cooker hood.
This module must be installed by a
Miele service technician or suitably
qualified electrician.
Use
To switch the fan on
Automatic switch-off of the Intensive
setting
You can set the Intensive setting so that
it only runs for 10 minutes before
reverting automatically to level III.
^ Press the On/Off control.
The fan runs at power level "II".
The indicator lamp will come on.
^ To set this option, both the fan and
the hob lighting must be switched off.
To select a power level
^ Press the run-on option control for
approximately 10 seconds. The first
fan setting indicator will light up.
^ Use the – / + controls to select the
power level required.
^ Then press, one after the other,
+ control = higher setting
– control = lower setting
Depending on the intensity of the
cooking vapours, levels I to III are
usually sufficient for normal cooking.
– the hob lighting control,
Intensive setting
When frying or cooking food with a
strong aroma, you may wish to select
the Intensive setting for a short period.
– the – control, and
– the hob lighting control again.
15
Use
Run-on option
The indicator lamps for fan power levels
I and IV will flash if the automatic
switch-off of the Intensive setting is not
activated.
^ Press the + control to activate automatic switch-off.
The indicator lamps for fan power
levels I and IV will now light up
constantly.
It is advisable to run the fan for a few
minutes after cooking is finished to
neutralise any lingering odours in the
air, whether you are using air extraction
or recirculation mode.
The fan can be set to switch off
automatically after either 5 or 15
minutes:
^ After cooking is finished, press the
run-on option control whilst the fan is
still running.
Press the – control to deactivate the
automatic switch-off function.
^ Press the run-on option control to
confirm your selection.
If you do not confirm your selection
within 4 minutes, the cooker hood will
automatically revert to the "old" setting.
– Press once = The fan will switch off
after 5 minutes (left-hand indicator
lamp).
– Press twice = The fan will switch off
after 15 minutes (right-hand indicator
lamp).
To switch off the run-on option, press
the run-on option control again. The
appliance will then not switch off
automatically.
To switch the fan off
^ Press the On/Off control to switch the
fan off.
The indicator lamp will go out.
16
Use
To switch the lighting on
Safety cut-out
The hob lighting can be switched on
and off independently of the fan.
Should the cooker hood be left on, the
fan will switch off automatically after 10
hours. The lighting will remain on.
^ Briefly press the lighting control to
switch on the hob lighting.
The indicator lamp will come on.
^ Pressing the On/Off control will
switch the fan back on again.
The lighting will switch on at maximum
brightness.
Dimming the lighting
The brightness of the lighting can be
adjusted.
^ With the lighting switched on, press
and hold the hob lighting control in.
The brightness will gradually dim until
you release the control.
^ Press the control in again to increase
the brightness to the level required
and then release it.
If you keep the control pressed in, the
light will continually change between
bright and dim.
To switch the lighting off
^ Press the hob lighting control briefly
to switch the lighting off.
The indicator lamp will go out.
17
Use
Filter operating hours counter
The number of hours the appliance has
been in operation is stored in memory.
The operating hours counter tells you
when the grease filter or charcoal filter
needs to be cleaned or replaced.
Resetting the operating hours
counter for the grease filter
After 30 hours of operation (or another
time if the operating hours counter has
been altered), the operating hours
indicator lamp will light up red. The
grease filter must then be cleaned.
Reading the operating hours counter
for the grease filter
To check the percentage of time set
already used:
^ Press the On/Off touch control to
switch the fan on.
^ Press and hold the operating hours
control in.
The indicator lamp will light up red.
Afterwards, the filter operating hours
counter must be reset.
^ Press the operating hours control for
about 3 seconds while the fan is
switched on.
One or more of the indicator lamps for
the – / + controls will flash.
The indicator lamp for the control will
go out.
The number of flashing lamps shows
the percentage of the operating time
which has already been used up.
1 lamp
2 lamps
3 lamps
4 lamps
= 25 %
= 50 %
= 75 %
= 100 %
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
18
Use
Altering the operating hours counter
for the grease filter
You can set the operating hours
counter for the grease filter to suit the
type of cooking you do.
– Select a short time if you roast or fry
a lot.
– If you use very little fat for cooking,
select a longer time.
– If you only cook occasionally we
recommend that you still select a
short time, because grease which
has built up gradually over a long
period of time will harden on the
grease filter and make cleaning more
difficult.
The operating hours counter for the
grease filter is set at the factory for 30
hours. The time set can be lengthened
or shortened: you can choose 20, 30,
40 or 50 hours.
The – / + control lamps show the time
which has been set:
1st lamp from the left = 20 hours
2nd lamp from the left = 30 hours
3rd lamp from the left = 40 hours
4th lamp from the left = 50 hours
^ Use the – / + controls to select the
desired time.
^ Confirm the selection by pressing the
operating hours control.
All the indicator lamps will go out.
If you do not confirm your selection
within 4 minutes, the cooker hood
will automatically revert to the "old"
data.
^ Press the On/Off control to switch the
fan off.
^ Press the run-on option control and
the operating hours control at the
same time.
The red indicator lamp for the operating
hours control and one of the – / +
control lamps will flash.
19
Use
Activating and altering the operating
hours counter for the charcoal filter
^ Confirm the selection by pressing the
operating hours control.
(...U models only)
All the indicator lamps will go out.
The charcoal filter is needed for
recirculation mode.
On delivery, the operating hours
counter for the charcoal filter is
switched off, and is set at unlimited.
For recirculation mode, the operating
hours counter needs to be set to the
required time:
^ Press the On/Off control to switch the
fan off.
If you do not confirm your selection
within 4 minutes, the cooker hood
will automatically revert to the "old"
data.
Resetting the operating hours
counter for the charcoal filter
The indicator lamp for the operating
hours control will light up blue after the
cooker hood has operated for the
number of hours set. The charcoal
filter must then be replaced with a new
one.
Afterwards, the operating hours counter
must be reset.
^ Press the + control and the operating
hours control at the same time.
The blue indicator lamp for the
operating hours control and one of the
– / + control lamps will flash.
^ Press the operating hours control for
about 3 seconds while the fan is
switched on.
The indicator lamp for the control will
go out.
The – / + control lamps show the time
which has been set:
1st lamp from the left = 120 hours
2nd lamp from the left = 180 hours
3rd lamp from the left = 240 hours
4th lamp from the left = unlimited
^ Use the – / + controls to select the
desired time.
20
Use
Reading the operating hours counter
for the charcoal filter
To check the percentage of time set
already used:
^ Press the On/Off touch control to
switch the fan on.
^ Press the operating hours control
twice in succession, and hold it
pressed in.
The indicator lamp will light up blue.
One or more of the indicator lamps for
the – / + controls will flash.
The number of flashing lamps shows
the percentage of the operating time
which has already been used up.
1 lamp
2 lamps
3 lamps
4 lamps
= 25 %
= 50 %
= 75 %
= 100 %
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
21
Cleaning and care
A range of Miele branded cleaning and
conditioning products is available to
order from Miele (see back page for
details) or via the internet at
www.miele-shop.com.
,Before any cleaning or
maintenance work is carried out,
disconnect the cooker hood from the
mains supply.
,Halogen lamps get very hot
during use and remain hot for some
time after being switched off. The
hot lamps are also susceptible to
damage from damp cleaning. Wait a
few minutes after switching off
before commencing cleaning.
Housing
General notes
The surfaces and controls are
susceptible to scratches and
abrasions. Please observe the
following cleaning instructions.
^ All external surfaces and controls can
be cleaned using warm water with a
small amount of washing-up liquid
applied with a well wrung-out soft
sponge or cloth.
^ Wipe the surfaces dry using a soft
cloth.
Do not use too much water when
cleaning the controls. Water could
penetrate into the electronics and
cause damage.
22
^ A microfibre "E-Cloth" is available
from the Miele UK Spare Parts
Department, which is suitable for
cleaning surfaces such as stainless
steel, glass, plastic and chrome
without the use of chemicals.
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents, e.g.
powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents.
These will damage the surface
material.
Important for appliances with
stainless steel housing
(This infomation does not apply to the
controls).
Stainless steel surfaces can be cleaned
using the Miele E-cloth or with a
proprietary non-abrasive cleaning
agent designed specifically for use on
stainless steel.
To help prevent re-soiling, a proprietary
conditioning agent for stainless steel
such as Neoblank (available from the
Miele UK Spare Parts Department) can
also be used. Follow the manufacturer’s
instructions, and apply sparingly with
an even pressure in the direction of the
"grain".
Cleaning and care
Important for appliances with
lacquered housing
(special finish)
It is very difficult to clean this type of
surface without causing minor marks to
the surface material. This can become
particularly noticeable with darker
colours and if there is halogen lighting
in the kitchen.
Controls
The controls may suffer
discolouration or damage if soiling is
left on them for too long. Remove
soiling straight away.
Grease filter
The re-usable metal grease filter in the
appliance removes solid particles from
the kitchen vapours (grease, dust, etc),
preventing soiling of the cooker hood.
The grease filter should be cleaned
regularly (at least every 3-4 weeks) to
avoid a built-up of fat, but always clean
immediately if the operating hours
control indicator lamp lights up red.
,An oversaturated filter is a fire
hazard.
Observe the General notes on cleaning
earlier in this section.
Do not use stainless steel cleaning
agents on the controls.
Glass surfaces
^ Glass surfaces can be cleaned using
a proprietary non-abrasive cleaning
agent designed specifically for use
on glass.
Do not use:
– abrasive cleaning agents, e.g.
powder cleaners and cream
cleaners,
– abrasive sponges, e.g. pot scourers
or sponges which have been
previously used with abrasive
cleaning agents,
^ To take out the grease filter, release
the locking clip on the filter, lower the
filter 45°, unhook it at the back and
remove it.
To avoid damaging the filter or the
hob below, make sure you hold the
filter securely at all times when
handling it.
– oven sprays.
23
Cleaning and care
Cleaning the grease filter by hand
^ Clean the filter with a soft nylon brush
in a mild solution of hot water and a
small amount of washing-up liquid.
Do not use "neat" washing up liquid.
Do not use:
– cleaning agents containing
descaling agents,
^ When removing the filter for cleaning,
also clean off any residues of oil or
fat from the now accessible housing
to prevent the risk of these catching
fire.
When putting the grease filter back in
position, ensure that the locking clip is
visible facing down towards the hob.
– powder cleaners, cream cleaners or
abrasive all-purpose cleaning agents,
– oven sprays.
Cleaning the grease filter in the
dishwasher
^ Place the filter as upright as possible
in the lower basket, with the short
sides upright. Make sure that the
spray arm can move freely.
^ Do not wash at more than 65° C. If a
Miele dishwasher is being used,
select the Sensor wash programme.
^ Use a mild dishwasher detergent.
Depending on the cleaning agent
used, cleaning the filter in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filter in any way.
^ After cleaning, leave the filter to dry
for a while on an absorbent surface
before putting it back in place.
24
^ If the grease filter is inadvertently
replaced upside down, insert a small
screwdriver blade into the slit to
disengage the clip.
^ After replacing the grease filter,
press the operating hours control for
approximately 3 seconds to reset the
operating hours counter.
The indicator lamp will go out.
^ If the grease filter is cleaned before
the operating hours counter has
reached its maximum, the operating
hours control should be pressed for
approximately 6 seconds to reset the
counter.
Cleaning and care
Fitting and replacing the
charcoal filter
If the cooker hood is connected for
recirculation, a charcoal filter must be
inserted in addition to the grease filter.
This is designed to absorb cooking
odours.
It is fitted in the canopy above the
grease filter.
New filters can be purchased from
your Miele dealer or from the Miele
Spare Parts Department.
See back cover for contact details,
and "Technical data" for the model
number of the filter.
^ Before fitting or replacing a charcoal
filter, the grease filter must first be
taken out (see previous section for
instructions on how to do this).
^ Take the charcoal filter out of its
packaging.
Always replace the charcoal filter immediately if
– the indicator lamp for the operating
hours control lights up blue,
or
– if it is no longer effective in absorbing
kitchen odours.
It should, however, be replaced at least
every 6 months.
Used charcoal filters can be disposed
of with the normal household waste.
^ After fitting a new charcoal filter,
press the operating hours control
twice and hold it pressed in for
approximately 3 seconds to reset the
operating hours counter.
The operating hours indicator lamp
will go out.
^ If a charcoal filter is replaced before
the operating hours counter has
reached its maximum, the operating
hours control should be pressed
twice and held pressed in for
approximately 6 seconds to reset the
counter.
^ Insert the charcoal filter into the
canopy.
^ Replace the grease filter.
When fitting for the first time:
^ Activate the operating hours counter
(see "Use").
25
Cleaning and care
Changing a halogen lamp
^ Before any cleaning or maintenance
work, disconnect the cooker hood
from the mains supply.
,Exercise caution when changing
halogen lamps. They get very hot
during use and remain hot for some
time after being switched off. Let
them cool down before you change
them.
^ To access the halogen lamp, push
the lamp cover gently upwards. The
cover will open and can be pulled
down.
^ Pull the old halogen lamp out of the
connection socket.
^ Using a cloth or glove, push the new
lamp (12 V, 20 W, G4 cap) carefully
into the connection socket. Please
follow the manufacturer's instructions.
^ Push the cover back up and make
sure it clicks into place.
26
After Sales Service
In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
– Your Miele Dealer / Chartered Agent
or
– The Miele Service Department (see
back cover for address).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. These are
shown on the data plate which is visible
when the grease filter is removed.
Guarantee
For information on the appliance
guarantee specific to your country
please contact Miele. See back cover
for contact details.
In the U.K. your appliance is
guaranteed for 2 years from the date of
purchase. To activate your cover call
0845 365 6640 or register online at
www.miele.co.uk
For G.B.: Please note that telephone
calls may be monitored and
recorded for training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
27
Appliance dimensions
1) Cut-out for feeding through the
exhaust ducting, the mains cable and,
with ... EXT models, the connection
cable to the external motor
In recirculation mode, only the mains
cable is required.
Exhaust connection C 150 mm (not
needed for recirculation mode)
DA 5100 D, DA 5100 D EXT
(Ceiling fixing viewed from above)
DA 5100 D U
(Ceiling fixing viewed from above)
28
The exhaust connection in the ceiling
plate is not fixed in the middle which
means that the hood can also be
installed where the exhaust cut-out in
the ceiling is not centrally positioned
over the hob. There is a max. margin of
30 mm in any direction.
Appliance dimensions
Safety distance between hob and
cooker hood
The minimum safety distances
between the top of a cooker or hob
and the bottom of the cooker hood
are as follows, unless a greater
distance is specified by the
manufacturer of your cooking
appliance:
550 mm (GB), 600 mm (AU, NZ)
above electric hobs and cookers,
650 mm above an open grill or
deep fat fryer,
650 mm above gas hobs and
cookers.
If this cooker hood is installed above
a Miele Wok CS 1028 CombiSet
appliance, a minimum safety
distance of 760 mm must be
maintained between the burner and
the lower edge of the cooker hood.
See "Warning and Safety" instructions
for further information.
A distance of 650 mm above the hob
may be preferable to give more working
space.
29
Installation
,Before installation, it is important
to read the information given on the
following pages as well as the
"Appliance dimensions" and the
"Warning and Safety instructions" at
the beginning of this booklet.
This is particularly crucial when
using the cooker hood at the same
time as a heating appliance that
relies on oxygen from the same
room to avoid the danger of toxic
fumes building up.
2 screws M4 x 8 mm
for securing the tower.
4 spacers to use in the event of an
uneven ceiling.
Installation instructions
See enclosed Installation sheet for
instructions on how to install this
appliance.
Assembly parts
1 floating bracket to give a choice of
position for the exhaust cut-out in the
ceiling (not required for ...U models)
4 screws 8 x 60 mm with
4 washers and
4 plugs S 10 to secure the cover plate
to the ceiling
1 hose clip for securing the exhaust
ducting to the exhaust stub
(not required for ...U models)
,The screws and plugs are for use
in concrete ceilings only.
For other types of construction,
alternative suitable fixings will be
required.
Make sure the ceiling is strong
enough to bear the weight of the
cooker hood.
30
Electrical connection
,All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national
and local safety regulations
(BS 7671 in the UK).
Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
manufacturer cannot be held liable.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
The connection data is given on the
data plate. (See "After Sales Service").
Ensure that this data matches the
household mains supply.
If the switch is not accessible after
installation (depending on country), an
additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to install
a residual current device (RCD) with a
trip current of 30 mA.
Important
This appliance is supplied for
connection to an a.c.
230 V single phase 50 Hz supply.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue
= neutral
Brown
= live
WARNING:
THIS APPLIANCE MUST BE
EARTHED
Connection of this appliance should be
made via a suitable isolator or a double
pole fused spur connection unit which
complies with national and local safety
regulations and the On-Off switch
should be easily accessible after the
appliance has been built in.
When switched off there must be an
all-pole contact gap of 3 mm in the
switch (including switch, fuses and
relays according to EN 60335).
31
Operation with DSM 400 control module
The Miele DSM 400 control module can
be used to combine the cooker hood
with other components.
It enables the following:
Potential free connection
This can be used to operate a further
appliance via the On/Off button s on
the cooker hood.
Components used in the central
ducting system are not supplied by
Miele.
If in any doubt, the advice of a
competent builder or, for gas, a Gas
Safe installer must be sought.
Connection to a light switch
The control module can be used to
switch on the cooker hood lighting and
also to dim it via a light switch in the
house.
Installation
The control module is fitted in the tower
after the cover plate has been
unscrewed from the ceiling.
The potential free contact on the
DSM 400 a can, for example, be used
in a cooker hood with an external motor
...EXT, which is connected to a central
ducting system.
The contact can then be used to
operate an electrically driven non-return
flap b which is connected to the
central extraction unit c.
32
The electrical connection of
components to the control module
must be carried out by a suitably
qualified and competent person.
Connection for air extraction
Important: To avoid the danger of
toxic fumes, please observe the
Warning and Safety instructions.
This is especially crucial when using
the cooker hood at the same time as
another heating appliance which
relies on air from the same room.
The cooker hood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
– Only use smooth pipes or flexible
hoses made from non-flammable
materials for the extraction ducting.
– When using an external motor, make
sure that the exhaust ducting is
sufficiently rigid. The external motor
can cause an underpressure which
could result in the exhaust ducting
distorting.
To achieve the greatest possible air
extraction with the lowest noise level,
please note the following:
– To ensure efficient air extraction, the
diameter of the exhaust ducting
should not be less than 150 mm.
– If flat ducting is being used, the
cross-sectional area must not be
smaller than the cross-sectional area
of the exhaust connection.
– The exhaust ducting should be as
short and straight as possible.
– Only use wide radius bends.
– The exhaust ducting should not be
kinked or compressed.
– Ensure that all connections are
strong and airtight.
– Where ducting is horizontal, it must
be laid to slope away at at least 1 cm
per metre. This is to ensure that
condensate cannot drain back into
the cooker hood.
33
Connection for air extraction
– If the exhaust air is to be ducted into
the open air, the installation of a
telescopic wall vent or roof vent is
recommended.
Condensate trap
(optional accessory)
– If the exhaust air is to be ducted into
a vent flue, the ducting must be
directed in the flow direction of the
flue.
Important.
If the exhaust ducting is to run through
rooms, ceiling space etc. where there
may be great variations in temperature
between the different areas, the
problem of condensation will need to
be addressed. The exhaust ducting will
need to be suitably insulated.
In addition to insulating the exhaust
ducting, we recommend that a suitable
condensate trap is also installed to
collect and evaporate any condensate
which may occur. Condensate traps
are available for C 125 mm or
C 150 mm ducting.
When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the
exhaust connection. The arrow on the
housing indicates the direction of
air-flow.
Cooker hoods designed for use with an
external motor (...EXT models) have an
integrated condensate trap.
34
Connection for air extraction
Silencer
...with air extraction:
(optional accessory)
The silencer not only reduces noise
from the fan, but also sounds from
outside (e.g. traffic noise).
For this reason the silencer must be
positioned as close as possible to where
the ducting leaves the building a.
...air extraction with external motor:
To achieve even further reductions in
noise levels, a special silencer can be
fitted in the ducting system...
To minimise noise from the motor in the
kitchen, the silencer should be
positioned in front of the external motor
b if possible, or if the ducting is long,
then in the ducting above the cooker
hood itself c.
In the case of an external motor placed
inside the house, fitting a silencer
behind the external motor d reduces
the noise of the motor outside the
house.
In all modes of operation, the most
effective noise reductions are
achieved if two silencers are fitted
one behind the other in the system.
35
Technical data
Total connected load* . . . . . . . . . 280 W
Fan motor* . . . . . . . . . . . . . . . . . 200 W
Hob lighting . . . . . . . . . . . . . . 4 x 20 W
Voltage . . . . . . . . . . . . . . . . . . AC 230 V
Frequency . . . . . . . . . . . . . . . . . . 50 Hz
Fuse rating (GB). . . . . . . . . . . . . . . 13 A
AUS, NZ:
Plug rating . . . . . . . . . . . . . . . . . . . 10 A
Test marks . . . . . . . . . . Electrical safety
. . . . . . . . . . . . . . . . . . . . . . C-Tick Mark
Electrically suppressed
according to AS/NZS 1044
Weight
DA 5100 . . . . . . . . . . . . . . . . . . . . 36 kg
DA 5100 D U. . . . . . . . . . . . . . . . . 36 kg
DA 5100 D EXT . . . . . . . . . . . . . 32.8 kg
Fan performance* according to
EN 61591
Extraction power on the DA 5100 D with
C 150 mm ducting:
Level I . . . . . . . . . . . . . . . . . . . 160 m3/h
Level II. . . . . . . . . . . . . . . . . . . 310 m3/h
Level III . . . . . . . . . . . . . . . . . . 450 m3/h
Intensive Setting . . . . . . . . . . . 620 m3/h
Recirculation power on the
DA 5100 D U with charcoal filter:
Level I . . . . . . . . . . . . . . . . . . . 130 m3/h
Level II. . . . . . . . . . . . . . . . . . . 230 m3/h
Level III . . . . . . . . . . . . . . . . . . 360 m3/h
Intensive Setting . . . . . . . . . . . 470 m3/h
Optional accessory for recirculation
mode:
- Miele charcoal filter DKF 12-1
* For EXT models the connected load
and extraction power will depend on
the type of external motor fitted.
Length of connection cable to external
motor. . . . . . . . . . . . . . . . . . . . . . . 1.4 m
36
37
38
39
Alteration rights reserved / 3011
M.-Nr. 09 202 760 / 00