Chauvet Q-Mix User manual

Q-Mix
Q-Mix™ DMX Lighting Effect
USER MANUAL
CHAUVET, 3000 N 29th Ct, Hollywood, FL 33020 U.S.A
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
www.chauvetlighting.com
2006-10-11/13:16
Table of Content
BEFORE YOU BEGIN........................................................................................................................................................... 3
WHAT IS INCLUDED .......................................................................................................................................................................................................... 3
UNPACKING INSTRUCTIONS.............................................................................................................................................................................................. 3
AC POWER ..................................................................................................................................................................................................................... 3
SAFETY INSTRUCTIONS .................................................................................................................................................................................................... 3
INTRODUCTION ................................................................................................................................................................... 4
FEATURES ....................................................................................................................................................................................................................... 4
DMX CHANNEL SUMMARY ............................................................................................................................................................................................... 4
PRODUCT OVERVIEW....................................................................................................................................................................................................... 5
SETUP ................................................................................................................................................................................... 6
LAMP............................................................................................................................................................................................................................... 6
Lamp Installation ................................................................................................................................................................................................ 6
POWER ........................................................................................................................................................................................................................... 6
MOUNTING ...................................................................................................................................................................................................................... 7
OPERATING INSTRUCTIONS.............................................................................................................................................. 8
CONTROL PANEL ............................................................................................................................................................................................................. 8
CONTROL PANEL FUNCTIONS .......................................................................................................................................................................................... 8
APPLYING CHANGES TO FUNCTIONS (QUICK INSTRUCTIONS) ............................................................................................................................................ 8
OPERATING MODES ......................................................................................................................................................................................................... 9
Master & Stand Alone (F6)................................................................................................................................................................................. 9
Setting Slave Fixtures ........................................................................................................................................................................................ 9
Sound-active (F4) or Auto-run (F5).................................................................................................................................................................... 9
DMX Mode........................................................................................................................................................................................................ 10
Daisy Chain Connection................................................................................................................................................................................... 10
MENU FUNCTIONS ......................................................................................................................................................................................................... 10
DMX-512 addressing ............................................................................................................................................................................................. 10
Setting the starting address ............................................................................................................................................................................. 10
Segment Display Configurations ........................................................................................................................................................................... 11
F8 - Display Invert ............................................................................................................................................................................................ 11
Service Functions .................................................................................................................................................................................................. 11
F3 - Fixture Reset (all motors) ......................................................................................................................................................................... 11
APPENDIX........................................................................................................................................................................... 12
DMX PRIMER ................................................................................................................................................................................................................ 12
Fixture Linking .................................................................................................................................................................................................. 12
DMX CHANNEL VALUES ................................................................................................................................................................................................ 13
MAINTENANCE ............................................................................................................................................................................................................... 14
RETURNS PROCEDURE .................................................................................................................................................................................................. 14
CLAIMS ......................................................................................................................................................................................................................... 14
GENERAL TROUBLESHOOTING ....................................................................................................................................................................................... 15
TECHNICAL SPECIFICATIONS .......................................................................................................................................................................................... 16
TECHNICAL SUPPORT .................................................................................................................................................................................................... 16
Q-Mix User Manual
2
2006-10-11/13:16
BEFORE YOU BEGIN
What is included
¾
¾
¾
¾
Q-Mix™ with ELC bulb
Power cord with plug
Manual
Warranty Card
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that
all parts are present, and have been received in good condition. Notify the shipper immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture
must be returned to the factory, it is important that the fixture be returned in the original factory box
and packing.
AC Power
To determine the power requirements for a particular fixture, see the label affixed to the back plate of
the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average
current draw under normal conditions. All fixtures must be powered directly off a switched circuit and
cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer
Figure 1 - AC Voltage Switch
channel is used solely for a 0% to 100% switch. Before applying power to a
fixture, check that the source voltage matches the fixture’s requirement.
Check the fixture or device carefully to make sure that if a voltage selection
switch exists that it is set to the correct line voltage you will use.
Warning!
Verify that the power select switch on your unit matches the
line voltage applied. All fixtures must be connected to circuits
with a suitable Earth Ground.
Safety Instructions
Please read these instructions carefully, which includes important
information about the installation, usage and maintenance?
•
•
•
•
•
•
•
Please keep this User Guide for future consultation. If you
sell the unit to another user, be sure that they also receive
this instruction booklet.
Always make sure that you are connecting to the proper
voltage and that the line voltage you are connecting to is
not higher than that stated on decal or rear panel of the
fixture.
This product is intended for indoor use only!
To prevent risk of fire or shock, do not expose fixture to
rain or moisture. Make sure there are no flammable
materials close to the unit while operating.
The unit must be installed in a location with adequate
ventilation, at least 50cm from adjacent surfaces. Be sure
that no ventilation slots are blocked.
•
Always disconnect from power source before servicing or
replacing lamp or fuse and be sure to replace with same
lamp source.
Caution!
Q-Mix User Manual
Secure fixture to fastening device using a safety chain.
Never carry the fixture solely by its head. Use its carrying
handles.
Maximum ambient temperature is Ta: 40°. Do not operate
fixture at temperatures higher than this.
•
In the event of serious operating problem, stop using the
unit immediately. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the
same type spare parts.
•
•
Don’t connect the device to a dimmer pack.
Make sure power cord is never crimped or damaged.
•
Never disconnect power cord by pulling or tugging on the
cord.
Avoid direct eye exposure to lamp while it is on.
•
There are no user serviceable parts inside the unit. Do not open the housing or
attempt any repairs yourself. In the unlikely event your unit may require service,
please contact CHAUVET.
3
2006-10-11/13:16
INTRODUCTION
Features
Control Features
•
•
•
•
2 channel DMX Intelligent Effect
Variable strobe
11 Gobo/Color combinations plus open
- Gobo wheel spin in both directions, at variable speeds
- Gobo Bounce™
Variable mirror reflector rotation in both directions
Features
•
•
•
•
•
•
•
•
Built in beat activated and automatic programs (stand-alone)
Linkable via Master/Slave
LED Display
Manual focus
Sound sensitivity knob
Micro-stepping motors
Thermal switch
Fan cooled
DMX Channel Summary
Q-Mix User Manual
CHANNEL
FUNCTION
1
Gobo
2
Gobo Wheel Rotation
4
2006-10-11/13:16
Introduction
Product Overview
3
2
1
4
1. Projector head
2. Projector
3. Hanging yoke
4. Fan (bottom rear)
5. LED display
6. LED power indicator
7. LED segment display
8. [Enter] button
9. [Choose] button
10. [Up] button
11. [Down] button
12. Voltage Selector Switch
13. DMX output
14. DMX input
14. Internal microphone
15. AC input IEC 60320 C14
15. Fuse holder
16. Control functions chart
17. Music Sensitivity Knob
16
5
15
13
7
Control Board
14
12
i
j
Enter
Choose
Up
Down
8
9
10
11
17
14
6
SEGMENT BUTTONS I/O PANEL OVERVIEW
BUTTONS
I/O PANEL
Choose
Toggles menu functions
DMX Out & In
DMX-512 connectors
Down
Steps backward through menu
functions
Power
AC input IEC 60320 C14 and fuse holder
Up
Steps forward through menu
functions
Enter
Confirms selected menu
function
Q-Mix User Manual
5
2006-10-11/13:16
SETUP
Lamp
You will need to install a lamp prior to the initial operation of the fixture. An ELC halogen lamp is
included.
Warning!
When replacing the lamp, please wait 15 minutes after powering down to allow the
unit to cool down! Always disconnect from main power prior to lamp replacement.
Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp
with alcohol and wipe it with a lint free cloth before installation.
L a mp I n s t a l l a t io n
1. Remove screws labeled (S1) and pull cover
plate.
2. The lamp is encased in a mirror reflector. Slide
entire reflector out of the lamp cage and
disconnect from socket. If replacing the lamp,
remove old lamp first.
3. Replace with new lamp and slide back into the
lamp cage.
4. Replace the cover, align the screw holes and
fasten the screws back onto the cover.
S1
Power
Your product is equipped with switch-selectable AC power setting.
Warning!
Verify that the power select switch on your unit
matches the line voltage applied. All fixtures must
be connected to circuits with a suitable Earth
Ground.
Slide switch up or down
depending on your line voltage.
• To determine the power requirements for a particular fixture,
see the label affixed to the back plate of the fixture or refer to the fixture’s specifications chart.
• A fixture’s listed current rating is its average current draw under normal conditions.
• All fixtures must be powered directly off a switched circuit and cannot be run off a rheostat
(variable resistor) or dimmer circuit, even if the rheostat or dimmer channel is used solely for a 0%
to 100% switch.
• Before applying power to a fixture, check that the source voltage matches the fixture’s
requirement.
• All fixtures must be connected to circuits with a suitable Earth Ground.
Pow er C able C onf igur at io n
CABLE
Q-Mix User Manual
PIN
INTERNATIONAL
BROWN
Live
L
BLUE
Neutral
N
YELLOW/GREEN
Earth
EG (Ground)
6
2006-10-11/13:16
Introduction
Mounting
O r ie ntat i on
Both fixtures can sit on stage or be mounted on a truss using a clamp in any position, provided, there
is adequate room for ventilation.
Warning
It is important never to obstruct the fan or vents pathway.
• When selecting installation location, take into consideration lamp replacement access and routine
maintenance.
• Safety cables should always be used.
• Never mount in places where the fixture will be exposed to rain, high humidity, extreme
temperature changes or restricted ventilation.
• The fixture must have a minimum of 1 meter distance from combustible materials.
1
2
1. Clamp
2. Fixture Yoke
3
3. Angle Adjustment
R ig g in g
The fixture includes a mounting yoke to which 1 rigging clamp can be bolted.
1. Align the clamp screw with the center hole on the yoke and tighten.
2. Verify the structure can hold 10 times the weight of all to-be installed fixtures.
3. Adjust the angle on the yoke arm as necessary.
Q-Mix User Manual
7
2006-10-11/13:16
OPERATING INSTRUCTIONS
Control Panel
On the control panel you can set the DMX address, set the fixture to Master/Slave mode, reset the
fixture and change fixture personality traits.
Control Board
[Enter] Confirms selection
[Choose] Access to main menu
[Up] Toggle menu items in a forward direction
[Down] Toggle menu items in a reverse direction
i
j
Enter
Choose
Up
Down
Control Panel Functions
FUNCTION
OPTIONS
Φ1
−Ψ/−ν
No Function
NOTES
Φ2
−Ψ/−ν
No Function
Φ3
−Ψ/−ν
Fixture reset
Φ4
−Ψ/−ν
Stand Alone (Sound-Active)
Φ5
−Ψ/−ν
Stand Alone (Auto Run)
Φ6
−Ψ/−ν
Master/Slave
Φ7
−ψ/−ν
No Function
Φ8
−Ψ/−ν
Display invert
Α001
000~512
DMX channel addressing
-y: Activates setting
-n: Disables, skips or selects alternative setting
Applying changes to Functions (Quick Instructions)
Unless other wise stated changes in the control panel can be applied in the following manner.
1. Press [Choose] button repeatedly until the display reads the menu function you wish to change as
illustrated in the table above in section “Control Panel Functions”
2. The display will read the previously stored settings for the desired function, for example, either
with a “-y” or a “-n” as in “F1-y or F1-n”.
3. Press the [Up] or [Down] button to toggle between either the “-y” or “-n” selection for that
particular menu function.
4. Press the [Enter] button to store your selection. The display will read “PASS” to confirm your
selection
Q-Mix User Manual
8
2006-10-11/13:16
Operating Modes
• A stand-alone mode will listen to sound and run through its diverse range of built in programs.
• Master/Slave mode will allow the command of up to as many units you want in a synchronized
light show to the sound.
• DMX control mode will provide the greatest flexibility and creativity. Each fixture trait can be
controlled individually using any universal DMX-512 controller.
Mast er & Sta nd A lon e (F 6)
In order to create the correct environment for Stand Alone
operation, several parameters have to be set in the control
panel. Please make the changes to the functions as listed in
the table below.
Note!
If the fixture is connected to a
controller, please disconnect it.
The display will read the previously
selected setting.
FUNCTION
SET TO
NOTES
F6
F4
A
-y
-y
001
Master mode (one Master only)
Sound activated
Channel address
Only one fixture can be the Master
assigned fixture. However, 16 units
can be slaved to the master unit.
S et t i ng S la ve F i xtu re s
The Master/Slave mode will allow you to link multiple units in a daisy chain fashion. In this mode, the
first unit in the daisy chain, the master, will automatically command all other units following. The first
unit will operate in a Stand/Alone mode and all units following will synchronize to the first unit. Up to
16 fixtures can be daisy chained in Master/Slave mode.
MENU
SET TO NOTES
F6
F4
A
-n
-n
001
Master mode
Sound activated
Channel address
S o un d-a ctive ( F 4) o r Au to- ru n ( F5)
In Master/Slave mode you can choose whether the fixture will run in a sound-active state where the
movement is triggered by sound or in auto-run where the speed is pre-programmed.
Q-Mix User Manual
MENU
SET TO NOTES
F4
or
F5
-n
Sound Activated
-n
Auto-run
9
2006-10-11/13:16
Operating Instructions
D MX Mo de
Operating in a DMX Control mode environment gives the user the greatest flexibility when it comes to
customizing or creating a show. You can tailor your programming to suit a specific event. Whether it
is a wedding where a spot light may be required or a lead singer requiring a color solo, the
opportunities are endless. In this mode you will be able to control each individual trait of the fixture
independently.
D a i s y C h a in C on ne ct i o n
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector
of the first fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin
connector to the input connector of the next fixture consisting of a (male) 3 pin connector. Then,
proceed to connect from the output as stated above to the input of the following fixture and so on.
Daisy Chain Connection
Controller not required for
Master/Slave operation
Menu Functions
DMX-512 addressing
This mode enables the use of a universal DMX controller device. Each fixture requires a "start
address" from 1 to 511. A fixture requiring one or more channels for control begins to read the data
on the channel indicated by the start address. For example, a fixture that occupies or uses 6 channels
of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101,
102, 103, 104, and 105. Choose start addresses so that the channels used do not overlap and notate
the start address selected for future reference.
If this is your first time addressing a fixture using the DMX-512 control protocol than I suggest jumping
to the Appendix Section and read the heading “DMX Primer”. It contains very useful information that
will help you understand its use.
S et t i ng t he sta rt in g a dd re ss
1. Press the [Choose] button until the display reads “ANNN” where N represents a number from 0 to
9.
2. Press the [Up] and [Down] buttons to increase or decrease values until the desired value is
achieved.
3. Press the [Enter] button to activate selection.
Q-Mix User Manual
10
2006-10-11/13:16
Segment Display Configurations
The display can be inverted making it easier to read the menu depending on the orientation of your
fixture.
F 8 - D is p la y In ve r t
FUNCTION
SET TO
NOTES
F8
F8
-y
-n
Invert display
Return to normal
Service Functions
F 3 - F i xtu re R ese t (a ll mot or s)
This function will re-initialize the fixture by returning all motors to its startup positions or otherwise
known as (home position).
Q-Mix User Manual
FUNCTION
SET TO
NOTES
F3
F3
-y
-n
Reset fixture
Skip function
11
2006-10-11/13:16
APPENDIX
DMX Primer
There are 512 channels in a DMX-512 connection. Channels may be assigned in any manner. A
fixture capable of receiving DMX-512 will require one or a number of sequential channels. The user
must assign a starting address on the fixture that indicates the first channel reserved in the controller.
There are many different types of DMX controllable fixtures and they all may vary in the total number
of channels required. Choosing a start address should be planned in advance. Channels should
never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is
set incorrectly. You can however, control multiple fixtures of the same type using the same starting
address as long as the intended result is that of unison movement or operation. In other words, the
fixtures will be slaved together and all respond exactly the same.
DMX fixtures are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is
where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which
the fixtures are connected is not important and has no effect on how a controller communicates to
each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures
using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The
shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET
carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’)
Figure 2 - DMX connector configuration
1
3
2
COMMON
INPUT
1
3
1
3
DMX +
2
2
DMX -
Resistance 120
ohm 1/4w between
pin 2 (DMX -) and
pin 3 (DMX +) of
the last fixture.
OUTPUT
Termination reduces signal errors and to
avoid signal transmission problems and
interference, it is always advisable to
connect a DMX signal terminator.
F i xtu re L in k in g
Note!
If you use a controller with a 5 pin DMX output connector, you will need to use a 5
pin to 3 pin adapter. CHAUVET Model No: DMX5M.
The chart below details a proper cable conversion:
3 PIN TO 5 PIN CONVERSION CHART
Q-Mix User Manual
Conductor
3 Pin Female (output)
5 Pin Male (Input)
Ground/Shield
Pin 1
Pin 1
Data ( - )signal
Pin 2
Pin 2
Data ( + ) signal
Pin 3
Pin 3
Do not use
Do not use
Do not use
Do not use
12
2006-10-11/13:16
Appendix
DMX Channel Values
DEFAULT
Q-Mix User Manual
VALUE
FUNCTION
1
000 Ù 005
006 Ù 039
040 Ù 045
046 Ù 051
052 Ù 057
058 Ù 063
064 Ù 069
070 Ù 075
076 Ù 081
082 Ù 087
088 Ù 093
094 Ù 099
100 Ù 105
106 Ù 111
112 Ù 129
130 Ù 135
136 Ù 141
142 Ù 148
149 Ù 153
154 Ù 159
160 Ù 165
166 Ù 171
172 Ù 177
178 Ù 183
184 Ù 189
190 Ù 196
197 Ù 225
226 Ù 255
Gobo
Blackout
Strobe: Slow > Fast
Open
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
Gobo 6
Gobo 7
Gobo 8
Gobo 9
Gobo 10
Gobo 11
Open
Gobo 1 Bounce™: Slow > Fast
Gobo 2 Bounce™: Slow > Fast
Gobo 3 Bounce™: Slow > Fast
Gobo 4 Bounce™: Slow > Fast
Gobo 5 Bounce™: Slow > Fast
Gobo 6 Bounce™: Slow > Fast
Gobo 7 Bounce™: Slow > Fast
Gobo 8 Bounce™: Slow > Fast
Gobo 9 Bounce™: Slow > Fast
Gobo 10 Bounce™: Slow > Fast
Gobo 11 Bounce™: Slow > Fast
Open
Scroll: Slow > Fast
2
000 Ù 005
000 Ù 005
000 Ù 005
000 Ù 005
Gobo Wheel Rotation
Static
Rotation Counter-Clockwise: Slow > Fast
Static
Rotation Clockwise: Slow > Fast
13
2006-10-11/13:16
Maintenance
To maintain optimum performance and minimize wear fixtures should be cleaned frequently. Usage
and environment are contributing factors in determining frequency. As a general rule, fixtures should
be cleaned at least twice a month. Dust build up reduces light output performance and can cause
overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off
fixture before conducting maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean all glass when the fixture is cold with a
mild solution of glass cleaner or Isopropyl Alcohol and a soft lint free cotton cloth or lens tissue. Apply
solution to the cloth or tissue and drag dirt and grime to the outside of the lens. Gently polish optical
surfaces until they are free of haze and lint. Do not to touch the lamp glass when cleaning fixture. Oil
and dirt can cause damage and premature aging of the lamp. In the event that the lamp is touched or
becomes dirty, clean the lamps with an alcohol wipe.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to
optimize light output. Cleaning frequency depends on the environment in which the fixture operates:
damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s
optics. Clean with soft cloth using normal glass cleaning fluid. - Always dry the parts carefully. - Clean
the external optics at least every 20 days. Clean the internal optics at least every 30/60 days.
Returns Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products
returned without an RA # will be refused. Call CHAUVET and request RA # prior to shipping the
fixture. Be prepared to provide the model number, serial number and a brief description of the cause
for the return. Be sure to properly pack fixture, any shipping damage resulting from inadequate
packaging is the customer’s responsibility. CHAUVET reserves the right to use its own discretion to
repair or replace product(s). As a suggestion, proper UPS packing or double-boxing is always a safe
method to use.
Claims
Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise. It is the customer's responsibility to notify and
submit claims with the shipper in the event that a fixture is damaged due to shipping. Any other claim
for items such as missing component/part, damage not related to shipping, and concealed damage,
must be made within seven (7) days of receiving merchandise.
Q-Mix User Manual
14
2006-10-11/13:16
Appendix
General Troubleshooting
Applies to
Symptom
Solution(s)
Lights
Foggers
& Snow
Controllers
Dimmers
& Chaser
Auto shut off
Check fan thermal switch reset
9
Beam is very dim or not
bright
Clean optical system or replace lamp
Check 220/110v switch for proper setting
9
Breaker/Fuse keeps
blowing
Check total load placed on device
Chase is too slow
Check users manual for speed adjustment
9
9
9
Device has no power
Check for power on Mains.
Check device’s fuse. (internal and/or external)
9
9
9
Fixture is not responding
Check DMX Dip switch settings for correct addressing
Check DMX cables
Check polarity switch settings
Fixture is on but there is
no movement to the
audio
Make sure you have the correct audio mode on the control
switches. If audio provided via ¼” jack, make sure a live audio
signal exists
Adjust sound sensitivity knob
9
9
Lamps cuts off
sporadically
Possible bad lamp or fixture is overheating.
Lamp may be at end of its life.
Light will not come on
after power failure
Some discharge lamps require a cooling off period before the
electronics in the fixture can kick start it again, wait 5 to 10
minutes before powering up
Loss of signal
Use only DMX cables
Install terminator
Note: Keep DMX cables separated from power cables or black
lights.
9
9
9
9
9
9
9
9
Motor movements are
jerky or jumpy
Possible bad motor driver or sensors
Check polarity switch on controller
9
Moves slow
Check 220/110v switch for proper setting
9
No flash
Re-install bulb, may have shifted in shipping
9
No light output
Check slip ring & brushes for contact
Install bulb
Call service technician
9
Relay will not work
Check reset switch
Check cable connections
Remote does not work
Make sure connector is firmly connected to device
9
Stand alone mode
All CHAUVET lighting fixtures featuring stand-alone functions
do not require additional settings, simply power the fixture and
it will automatically enter into this mode
9
Unit wobbles when
rotating
Check for damages possibly incurred during shipping
Q-Mix User Manual
9
9
9
15
9
9
2006-10-11/13:16
Appendix
Technical Specifications
WEIGHT & DIMENSIONS
Length......................................................................................................................... 349 mm (13.75 in)
Width ............................................................................................................................... 305 mm (12 in)
Height .............................................................................................................................. 254 mm (10 in)
Weight ............................................................................................................................ 9 Kgs (20.2 lbs)
POWER
Switch-selectable power settings ..................................................................115V 60 Hz or 230V 50 Hz
AC input............................................................................................................ 3 prongs IEC 60320 C14
European version .................................................................................................................. 240V 50 Hz
LAMPS
ELC............................................................................................................................... 250W 24V MR16
PHOTO OPTIC
Beam Angle ........................................................................................................................................ 27°
THERMAL
Maximum ambient temperature............................................................................................ 40° (104° F)
FUSE
Main (115V) ................................................................................................ 20mm Glass 6.3A Fast Blow
Internal PCB .................................................................................................. 20mm Glass 5A Fast Blow
CONTROL & PROGRAMMING
Data input ................................................................................................ locking 3-pin XLR male socket
Data output ........................................................................................... locking 3-pin XLR female socket
Data pin configuration ..............................................................................pin 1 shield, pin 2 (-), pin 3 (+)
Protocols........................................................................................................................ DMX-512 USITT
DMX Channels .......................................................................................................................................2
ORDERING INFORMATION
Q-Mix™ DMX Intelligent Effect Light .............................................................................................. Q-Mix
Fuse 6.3A .........................................................................................................................P170FUSE006
Fuse 5A ............................................................................................................................P170FUSE005
Technical Support
Address:
Service Dept.
th
3000 N 29 Ct, Hollywood, FL 33020 (U.S.A.)
Support (Email):
[email protected]
Telephone:
(954) 929-1115 - (Press 4)
Fax:
(954) 929-5560 - (Attention: Service)
Website:.................................................................................................. http://www.chauvetlighting.com
Q-Mix User Manual
16
2006-10-11/13:16