Sharp DK-KP95P Specifications

ENGLISH
MODEL
DK-KP95P
SLIM MICRO SYSTEM
OPERATION MANUAL
Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual
carefully. It will guide you in operating your SHARP product.
AirPlay, the AirPlay logo, iPad, iPhone, iPod, iPod
classic, iPod nano, and iPod touch are trademarks of
Apple Inc., registered in the U.S. and other countries.
“DLNA®, the DLNA Logo and DLNA CERTIFIED® are
trademarks, service marks, or certification marks of the
Digital Living Network Alliance.”
“Made for iPod,” “Made for iPhone,” and “Made for iPad” mean that an electronic accessory has been designed to connect
specifically to iPod, iPhone, or iPad respectively, and has been certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, iPhone, or iPad may affect wireless performance.
Accessories
The following accessories are included.
Remote control x 1
(RRMCGA286AWSA)
Stand for iPad x 1
(GITAUA014AW01)
AM loop antenna x 1
(QANTL0005AWZZ)
FM antenna x 1
(FANTI1535A)
Dock Spacer x 1
(PSPAGA003AWZZ)
Special Note
Supply of this product does not convey a license nor imply any right to distribute content created with this product in
revenue-generating broadcast systems (terrestrial, satellite, cable and/or other distribution channels), revenue-generating
streaming applications (via Internet, intranets and/or other networks), other revenue-generating content distribution
systems (pay-audio or audio-on-demand applications and the like) or on revenue-generating physical media (compact
discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like). An independent license for such
use is required. For details, please visit http://mp3licensing.com
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.
*TINSZB210AWZZ4W*|
TINSZB210AWZZ
Printed in Malaysia
SHARP CORPORATION
12C R MW 1
System connections
Make sure to unplug the AC power cord before making any connections.
FM antenna
MODEL NO. DK-KP95P
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
SLIM MICRO SYSTEM
AC 120V
60Hz
26W
FREQUENCY RANGE : FM 87.5 - 108.0 MHz
AM 530 - 1,710 kHz
External FM
antenna for
better reception
(not supplied)
MADE IN MALAYSIA
FABRIQUÉ IN MALAISIE
MARKETED BY : SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH, NEW JERSEY 07495 - 1163
“THIS PRODUCT COMPLIES WITH DHHS STANDARDS 21 CFR,
SUBCHAPTER J. PART 1040. 10”
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
TSPC-B605AWZZ
AC outlet
(AC 120 ~ 60 Hz)
■
AM loop antenna
■
Antenna connection
Supplied FM antenna:
Connect the FM antenna wire to the FM 75 OHMS jack and position the FM
antenna wire in the direction where the strongest signal can be received.
External FM antenna:
Use an external FM antenna (75 ohms coaxial cable) for better reception. When
an external FM antenna is used, disconnect the supplied FM antenna wire.
Supplied AM loop antenna:
Connect the AM loop antenna to the AM and earth (GND) terminals. Position
the AM loop antenna for optimum reception. Place the AM loop antenna on a
shelf, etc., or attach it to a stand or a wall with screws (not supplied).
Installing the AM loop antenna:
<Assembling>
AC power connection
After checking all the connections have been made correctly, plug the AC
power cord of this unit into the AC outlet.
Note:
Unplug the AC power cord from the AC outlet if the unit will
not be in use for a prolonged period of time.
■
Demonstration (Network stand-by) mode
● The first time the unit is plugged in, the unit will enter
the demonstration mode. (refer page 4)
<Attaching to the wall>
Wall
Screws
(not supplied)
Note:
Placing the antenna on the unit or near the AC power cord may cause noise
pickup. Place the antenna away from the unit for better reception.
● To cancel the demonstration mode, press the DEMO
button (remote control) during power stand-by mode.
The unit will enter the low power consumption mode.
● To return to the demonstration mode, press the DEMO
button again.
● If iPod or iPhone is docked, the unit will begin charging.
“Charge Mode” will be displayed. Demonstration mode
is invalid during charge mode.
Remote control
■
Battery installation
Use 1 “AA” size battery (UM/SUM-3, R6, HP-7 or similar).
Battery is not included.
1 Open the battery cover.
2 Insert the supplied battery according to the terminal
indicated in the battery compartment.
When inserting or removing the battery, push it towards the
(–) battery terminals.
3 Close the cover.
E-1
Caution:
● Remove the battery if the unit will not be used for a long
period of time. This will prevent potential damage due to
battery leakage.
● Do not use rechargeable battery (nickel-cadmium battery,
etc.).
● Installing the battery incorrectly may cause the unit to
malfunction.
● Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the
like.
Notes concerning use:
● Replace the battery if the operating distance is reduced or
if the operation becomes erratic. Purchase an “AA” size
battery (UM/SUM-3, R6, HP-7 or similar).
● Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
● Exposing the sensor on the unit to strong light may
interfere with operation. Change the lighting or the
direction of the unit if this occurs.
● Keep the remote control away from moisture, heat, shock,
and vibrations.
General control
■
AirPlay auto switch
During other function (CD, TUNER, USB, iPod, Audio In), when you select DKKP95P speaker through AirPlay icon on your AirPlay device, the unit will
automatically switch to Network function and stream the music from your AirPlay
device.
This condition applies when:
The AirPlay network has previously been set up between the unit and your
AirPlay device.
■
X-Bass control
When the power is first turned on, the unit will enter the extra
bass mode which emphasises the bass frequencies, and
“X-BASS” indicator will appear. To cancel the extra bass mode,
press the X-BASS button on the remote control.
■
■ Bass control
1 Press the BASS/TREBLE button to select “Bass”.
2 Within 5 seconds, press the VOLUME (+ or –) button to adjust the bass.
To turn the power on
Press the POWER ON/STAND-BY button to turn the power on.
After use:
Press the POWER ON/STAND-BY button to enter the
power stand-by mode.
■
■ Treble control
1 Press the BASS/TREBLE button to select “Treble”.
2 Within 5 seconds, press the VOLUME (+ or –) button to adjust the treble.
Display brightness control
To dim the display brightness, press the DIMMER button on
the remote control.
Dimmer 1 (Display is dim).
Dimmer 2 (Display gets dimmer).
■
Dimmer off (Display is bright).
■
NETWORK
Volume auto fade-in
Audio In
If you turn off and on the main unit with the volume set to 27 or
higher, the volume starts at 16 and fades in to the last set level.
■
Volume control
Auto power off function
The main unit will enter the stand-by mode (when iPad, iPod or
iPhone is not connected) after 15 minutes of inactivity during:
iPod :
Not docked.
Audio In : No detection of input signal.
CD :
In the stop mode or no disc.
USB :
In the stop mode or no media.
Note:
However, if iPod or iPhone is docked, the unit will begin
charging. “Charge Mode” will be displayed.
■
Muting
The volume is muted temporarily when pressing the MUTE
button on the remote control. Press again to restore the volume.
■
USB
Wi-Fi network Setup for AirPlay / DLNA
Direct key power on function
When you press any of the following buttons, the unit turns on.
● iPod, CD/USB, AUDIO IN, TUNER, NETWORK on the
remote control: Selected function is activated.
●
/ button on the main unit: The unit turns on and
playback of the last function will start (CD, TUNER, USB,
iPod, AUDIO IN, NETWORK)
■
AM
iPod
Note:
The backup function will protect the memorized function mode for
a few hours should there be a power failure or the AC power cord
becomes disconnected.
Press VOL +/- to increase or decrease the volume.
■
Function
When the FUNCTION button on main unit is pressed, the current
function will change to different mode. Press the FUNCTION
button repeatedly to select desired function.
FM MONO
CD
FM STEREO
Auto power on
During stand-by mode, when you select DK-KP95P speaker
through AirPlay icon on your AirPlay device, the unit will
automatically power on to Network function and stream the
music from your AirPlay device.
This condition applies when:
● The AirPlay network has previously been set up
between the unit and your AirPlay device.
● Set the Network Stand-by mode to ON. (refer page 4)
(AirPlay)
With Apple AirPlay technology, you can stream your music from your
iTunes on a Mac, PC, iPhone, iPod touch, or iPad to external speakers
(DK-KP95P) via a Wi-Fi network.
AirPlay usage requires:
● MacBook or MacBook Pro running MacOS 10.6.6 or greater.
● iTunes 10.2 or greater (Mac/PC).
● iOS 4.3 or later
- iPod touch (4th, 3rd and 2nd generation)
- iPhone 4
- iPhone 3GS (iPhone 3G cannot support AirPlay)
- iPad 2
- iPad
(DLNA)
DLNA technology enables you to share media from one device to
another via a Wi-Fi network.
DLNA usage requires:
● DLNA compatible devices with appropriate application. (Refer to
your devices’ manual) Support status varies depending on model
and software features such as client and server functions.
● PC with Windows 7.
● DLNA version 1.5
● This product supports audio source with playback capability only.
Streaming (audio and video) from DLNA devices is not supported
by this product.
● DRM file playback (DTCP-IP) is not supported.
● SHARP does not guarantee that this product will work with all
DLNA compatible devices and wireless LAN routers.
Note:
When this unit is placed too near a Wireless LAN device or microwave,
noise interference may occur, causing crackling sound. It may also
reduce the communication speed and cause invalid connection. If these
happen, do the following:
- Place the unit away from the Wireless LAN device or microwave.
- Place the unit closer to the source device.
E-2
Wi-Fi network Setup for AirPlay / DLNA (continued)
7 On the iPod touch/iPhone/iPad, select ‘Settings’ --> ‘Wi-Fi’.
■ Direct wireless connection
1 Press the POWER ON/STAND-BY button.
2 Press the NETWORK button.
3 Press the iPod MENU button on the remote control.
4 Press the / button to select ‘Wi-Fi Setup’.
On the PC/Mac, enter the list of available wireless networks.For
other DLNA compatible devices, turn on the Wi-Fi. For more
details, refer to your devices’ manual.
8 Select your router from the list of available networks. Enter your
network password if required.
Press the ENTER button.
/
button to select ‘Direct’. Press the
ENTER button. Wait until ‘ • ’ on the display turns off and
shows ‘Direct Ready’ which takes about 40 seconds.
6 On the iPod touch/iPhone/iPad, select ‘Settings’ -->
‘Wi-Fi’. On the PC/Mac, enter the list of available
wireless networks
5 Press the
9 Continue with step 8 to 9 in ‘Direct wireless connection’.
Note:
WPS process (network search) takes about 2 minutes. If
fail to connect, the display will show ‘Cannot connect to
Network’. Repeat step 4 to retry.
Wi-Fi
■
SHARP_DK-KP95
For other DLNA compatible devices, turn on the Wi-Fi.
For more details, refer to your devices’ manual.
7 Select SHARP_DK-KP95 from the list of available
networks.
8 Launch Music and play desired song on your iPod touch /
iPhone or iPad. For PC/Mac, launch iTunes.
For other DLNA compatible devices, launch the DLNA
compatible media software. For more details, refer to your
devices’ manual.
1
2
3
4
5
6
9 Tap / click on the AirPlay icon
.
Select the speaker : SHARP_DK-KP95_xxxxxx.
Sound will be heard from the DK-KP95 speakers via
audio streaming.
7
8
Note: ‘xxxxxx’ is MAC ID.
Connection via SSID (wireless router without WPS)
Press the POWER ON/STAND-BY button.
Press the NETWORK button on the remote control.
Press the iPod MENU button on the remote control.
Press the / button to select ‘Wi-Fi Setup’.
Press the ENTER button.
Press the
/
button to select ‘SSID Set’. Press the
ENTER button. Wait until the display shows “SSID
Ready” which takes about 40 seconds.
On the iPod touch/iPhone/iPad, select ‘Settings’ -->
‘Wi-Fi’. On the PC/Mac, enter the list of available
wireless networks.
For other DLNA compatible devices, turn on the Wi-Fi.
For more details, refer to your devices’ manual.
Select Sharp_DK-KP95 from the list of available
networks.
Open web browser as Safari or Explorer on iPod touch /
iPhone / iPad or PC/Mac. Type 192.168.1.1 at the
address bar.
The DK-KP95 configuration page is displayed.
SHARP DK-KP95
SHARP_DK-KP95_xxxxxx
192.168.1.1
Network Configuration
■
Connection via wireless router with WPS
9 Select Network Configuration tab.
10 Select your router SSID from the pull-down list of
1 Press the WPS button on the wireless router.
Service Set ID (SSID).
WPS
2
3
4
5
Press the POWER ON/STAND-BY button.
Press the NETWORK button.
Press the iPod MENU button on the remote control.
Press the / button to select ‘Wi-Fi Setup’.
Press the ENTER button.
6 Press the / button to select ‘WPS’. Press the ENTER
button. Wait until ‘
’ on the display stop blinking and the
display shows "Successfully Connected to [network name]".
E-3
Wi-Fi network Setup for AirPlay / DLNA (continued)
11 Enter your network password if required (for some
routers, you may also need to tick DHCP under
Advance Setting).
12 Change the name of SHARP_DK-KP95_xxxxxx in
AirPlay Device Name if you like and click Apply (*1).
13 Click Apply (*2) at the bottom of the page to apply your settings.
■
Various function control during AirPlay / DLNA
Various function can be controlled from the remote control
or your AirPlay / DLNA device.
Function
Main unit
Remote
control
AirPlay
device
Volume up/
down
*1
Play/pause
*2
Next/previous
track
Mute
14 Click OK to confirm your settings.
15 On the iPod touch/iPhone/iPad, select ‘Settings’ --> ‘Wi-Fi’.
Display
On the PC/Mac, enter the list of available wireless networks.
16 Select your router from the list of available networks.
17 Continue with step 8 to 9 in ‘Direct wireless connection’ of
page 2.
■
Notes:
● For DLNA compatible devices, the function control may
vary depending on DLNA application used.
● To enable this unit to control iTunes software, the
setting below is required.
For Mac iTunes:
1 On the toolbar menu, click iTunes and select
Preferences.
2 Under Devices tab, check the ‘
Allow iTunes
audio control from remote control speakers’ box.
Connection of an AirPlay device to the
same Wi-Fi network
For Window iTunes:
1 On the toolbar menu, click Edit and select
You can add other AirPlay devices to join the same Wi-Fi
network as the unit.
1 On the iPod touch/iPhone/iPad, select ‘Settings’ --> ‘Wi-Fi’.
On the PC/Mac, enter the list of available wireless networks.
For other DLNA compatible devices, turn on the Wi-Fi. For
more details, refer to your devices’ manual.
2 Select your router SSID from the list of available wireless
networks.
Preferences.
2 Under Devices tab, check the ‘
Allow iTunes
control from remote control speakers’ box.
■
Network Stand-by mode
On: Network Stand-by mode is enable.
During stand-by mode, if select DK-KP95 speakers
through AirPlay icon and tap/click PLAY on AirPlay device,
the unit will automatically power on and stream the music
from your AirPlay device.
To enable the Network Stand-by mode :
During Stand-by mode, press DEMO button on remote
control to select the Network Stand-by mode on or off.
3 Wait until successful Wi-Fi connection from the
additional AirPlay devices to the router.
4 Continue with step 8 to 9 in ‘Direct wireless connection’ of page 3.
Notes:
● This product may face some irregularities due to various unforseen
reasons from other devices in the process of Wi-Fi pairing. Should
this happen, unplug the AC power cord, and plug it back in.
● If the Network function operates incorrectly, do the Network reset
(refer page 14).
To check the IP address of the router / Mac ID / SSID:
1 Press iPod MENU button on the remote control.
2 Press / button on the remote control repeatedly.
The display will toggle as below:
Wi-Fi Setup
Mac ID
E-4
SSID
(when using router)
IP address
Listening to the iPod, iPhone or iPad
Made for:
● iPod touch (4th generation)
● iPod touch (3rd generation)
● iPod touch (2nd generation)
● iPod touch (1st generation)
● iPod classic
● iPod nano (6th generation)
● iPod nano (5th generation)
● iPod nano (4th generation)
■ iPod, iPhone or iPad playback via USB terminal
1 Press the POWER ON/STAND-BY button to turn the power on.
2 Press the CD/USB button on the remote control or FUNCTION
● iPod nano (3rd generation)
● iPod nano (2nd generation)
● iPhone 4
● iPhone 3GS
● iPhone 3G
● iPhone
● iPad 2
● iPad
button repeatedly on the main unit to select USB function.
3 Connect iPod, iPhone or iPad to the unit. “USB/iPod” will appear.
Caution:
Please update your iPod, iPhone and iPad unit to the latest
software version before using it. Please visit Apple’s
homepage to download the latest version for your iPod,
iPhone and iPad.
Notes:
● Charging terminal for iPod, iPhone and iPad:
Condition
DOCK
USB terminal
USB function
YES
YES
(without iPod
or iPhone
docking)
Other function
YES
NO
(iPod / CD / Network
Tuner / Audio In)
Stand-by
YES
NO
● The message “This accessory is not made to work with
iPhone” or similar, may appear on the iPhone screen
when:
- battery is low.
- the iPhone is not properly docked (eg. slanting).
If this occurs, remove and re-dock the iPhone.
● This product is made for iPod, iPhone and iPad. To
prevent random interference when iPod, iPhone or
iPad is connected, the headphone output of main unit
is disabled, and “HP INVALID” will be displayed.
You may also experience brief audio interference
during incoming calls.
● The headphone output of main unit is switched off during
inserting iPod, iPhone and iPad unit. This is an Apple
product specification.
■
File name
4 Press the / (USB / ) button to start playback.
Note:
Stop button ( ) is invalid during iPod, iPhone or iPad
playback
■
iPhone playback
● Sound will only switch from iPhone to the main unit after
authentication process is completed in approximately 10
seconds.
● Incoming calls will pause the playback.
● Once the calls are answered, the conversation can only be
heard through the built-in iPhone speaker. Turn on the
iPhone speaker or undock the iPhone to start conversation.
■
iPod and iPhone connection (Dock only)
Caution:
Unplug all accessories from the iPod or iPhone before
inserting it into the dock.
Note:
Docking station is not recommended for iPad connection.
1 Open the docking station for iPod and
iPhone by pulling up the cover.
2 Dock your iPod or iPhone into the unit.
iPhone (bottom)
iPod, iPhone and iPad connection via USB terminal
iPhone
1 Insert the connector to the iPod, iPhone or iPad.
iPad
Dock connector
Dock for iPhone
Connector
2 Place the iPad to the stand for iPad.
For iPod nano or iPod touch :
For additional support, apply dock spacer (supplied) as shown.
iPad
Peel off
separator
Stand for iPad
3 Connect the iPod,
Rib
iPod
docking
cover
USB
iPhone or iPad to
the unit via USB
connector.
Dock spacer
1 Peel off the double sided tape separator.
2 Place the spacer between the two ribs of the iPod docking
cover as shown.
E-5
Listening to the iPod, iPhone or iPad (continued)
■
■
iPod or iPhone playback
1 Press the POWER ON/STAND-BY button to turn the power on.
2 Press the iPod button on the remote control or FUNCTION
Function Main unit
Dock/USB
Play
button repeatedly on the main unit to select iPod function.
3 Insert iPod or iPhone unit into the dock of main unit. “DOCK
OK” will appear.
4 Press the / (iPod
Various iPod, iPhone and iPad functions
/ ) button to start playback.
Navigating the iPod, iPhone or iPad menus
■
Press in the pause
mode.
Press in the playback
mode.
Track up/
down
Press in the playback
or pause mode.
If you press the
button in the pause
mode, press the /
button to start the
desired track.
Press and hold down
in the playback
mode.
Release the button to
resume playback.
Press to toggle
repeat mode.
Repeat
____
1 Press the iPod MENU button to view the menu on iPod,
iPhone or iPad unit. Press it again to go back to previous
menu.
2 Use the PRESET ( or ) button to select an item on the
menu and then press ENTER button.
Note:
When navigating the iPod, iPhone or iPad menu with remote
control, do not operate any of the buttons on the iPod or
iPhone unit. The volume level is adjusted by pressing the VOL
(+ or –) button on the main unit or the remote control.
Adjusting the volume on the iPod, iPhone or iPad units give no
effect.
iPod, iPhone and iPad operations:
The operations described below depend on the generation
iPod, iPhone and iPad you are using.
System on operation:
When the main unit is powered on, the iPod, iPhone or iPad
units will automatically power on when docked or connected
in the unit.
System off (stand-by operation):
When the main unit is turned to stand-by mode, the docked
iPod, iPhone or connected iPad unit will automatically turn to
stand-by mode.
Operation
Pause
Fast
forward/
reverse
■
Remote control
Dock
USB
Shuffle
Press and hold to
toggle shuffle mode.
Press to view the iPod
menu during iPod
function.
Menu
____
Enter
____
Press to confirm the
selection.
Cursor
Up/Down
____
Press to select the
iPod menu.
To disconnect iPod, iPhone or iPad
Simply remove the iPod or iPhone from the docking station or
iPad connector from USB terminal. It is safe to do so even
during playback.
Caution:
● Unplug all accessories for the iPod or iPhone before
inserting it into the docking station.
● Stop button ( ) at main unit is invalid during iPod function.
E-6
Listening to a CD or MP3/WMA disc
A. For example, to choose 13
1 Press the “10+” button once.
2 Press the “1” button.
3 Press the “3” button.
Selected track number
B. For example, to choose 130
1 Press the “10+” button twice.
2 Press the “1” button.
3 Press the “3” button.
4 Press the “0” button.
Notes:
● A track number higher than the number of tracks on the
disc cannot be selected.
● During random play, direct search is not possible.
To stop playback:
● Press the (CD ) button.
■
■
Disc playback
Various disc functions
Function
1 Press the POWER ON/STAND-BY button to turn the power on.
2 Press the CD/USB button on the remote control or FUNCTION
button repeatedly on the main unit to select CD function.
3 Press the OPEN/CLOSE button
to open the disc compartment.
4 Place the disc in the disc
compartment, label side front.
5 Press the OPEN/CLOSE button
to close the disc compartment.
Main
unit
Remote
control
Operation
Play
Press in the stop mode.
Pause
Press in the playback
mode. Press the /
button to resume
playback from the
paused point.
Press in the playback
mode.
Stop
6 Press the / (CD
/ ) button to start playback. After the
last track is played, the unit will stop automatically.
Caution:
● Do not place two discs in the disc compartment.
● Do not play discs of special shapes (heart, octagon, etc). It
may cause malfunctions.
● Do not push the disc compartment while it is moving.
● If the power fails while the compartment is open, wait until the
power is restored.
● If TV or radio interference occurs during CD operation, move
the unit away from the TV or radio.
● Be sure to place 8 cm (3") disc in the middle of the disc
compartment.
● Due to the structure of the disc information, it takes longer to
read an MP3/WMA disc than a normal CD (approximately 20
to 90 seconds).
Notes for CD or MP3/WMA disc:
● When the end of the last track is reached during fast forward,
“END” will appear on the display and CD operation will be
paused. When the beginning of the first track is reached
during fast reverse, the unit will enter the playback mode (only
for CD).
● Rewritable multi-session discs with unfinished writing, can
still be played.
■
Direct track search
By using the Numeric buttons, the desired tracks on the
current disc can be played.
Use the Numeric buttons on the remote control to select
the desired track while playing the selected disc.
● The Numeric buttons allow you to select up to number 9.
● When selecting number 10 or higher, use the “10+” button.
E-7
Track
up/
down
Fast
forward/
reverse
■
Press in the playback or
stop mode.
If you press the button in
the stop mode, press the
/ button to start the
desired track.
Press and hold down in
the playback mode.
Release the button to
resume playback.
Repeat play
Repeat play can play one track, all tracks or a programmed
sequence continuously.
To repeat one track:
Press the PLAY MODE button repeatedly until “Repeat One”
appears. Press the / (CD / ) button.
To repeat all tracks:
Press the PLAY MODE button repeatedly until “Repeat All”
appears. Press the / (CD / ) button.
To repeat desired tracks:
Perform steps 1 - 4 in “Programmed play” section on page 8
and then press the PLAY MODE button repeatedly until
“Repeat All” appears.
To cancel repeat play:
Press the PLAY MODE
button repeatedly until
“Normal” appears and
“
” disappears.
Caution:
After performing repeat play, be sure to press the (CD )
button. Otherwise, the disc will play continuously.
Listening to a CD or MP3/WMA disc (continued)
■
Random play (shuffle)
The tracks on the disc can be played in random order
automatically.
To random play all tracks:
Press and hold the PLAY MODE button on the remote control
until “Random” appears. Press the / (CD / ) button.
To cancel random play:
Press the PLAY MODE
button again. “RDM”
indicator will disappear.
Notes:
● If you press the
button during random play, you can
move to the track selected next by the random operation.
On the other hand, the
button does not allow you to
move to the previous track. The beginning of the track
being played will be located.
● In random play, the unit will select and play tracks
automatically. (You cannot select the order of the tracks.)
■
Programmed play (CD)
To cancel the programmed play mode:
During programmed stop mode, press the
(CD )
button. The display will show “Memory Clear” and all the
programmed contents will be cleared.
Adding tracks to the program:
If a program has been previously stored, the “MEM”
indicator will be displayed. Press the MEMORY button.
Then follow step 2 to add tracks.
Notes:
● When the disc compartment is opened, the program is
automatically canceled.
● If you press the POWER ON/STAND-BY button to
enter the stand-by mode or change the function from
CD to another, the programmed selections will be
cleared.
● During the program operation, random play is not
possible.
■
Procedure to playback MP3/WMA disc with
folder mode on
To play back CD-R/RW.
You can choose up to 32 selections for playback in the order
you like.
1 Press the CD/USB button, and load an MP3/WMA disc. Press
the FOLDER button and disc info will be displayed.
1 While in the stop mode, press the MEMORY button on the remote
MP3 indicator
WMA indicator
control to enter the programming save mode.
TOTAL indicator
2 Press the Numeric button
on the remote control to
select the desired track.
Selected track number
Total number of folder
Note: To select track number 10 or higher, refer ’Direct
track search’.
2 Press the PRESET (
or ) button to select desired
playback folder. (Folder mode on)
3 Repeat step 2 for other tracks. Up to 32 tracks can be programmed. If
FOLDER
indicator
you want to check the programmed tracks, press the MEMORY
button repeatedly. If you make a mistake, the programmed tracks can
be cleared by pressing the CLEAR button.
4 Press the
■
/ (CD
/ ) button to start playback.
Programmed play (MP3/WMA)
FOLDER number
First track number
in the folder
3 Select desired file to be played back by pressing the
or
1 While in the stop mode, press the MEMORY button to
enter the programming save mode.
Total number of files
button.
4 Press the
/ (CD / ) button. Playback will start and
file name will be displayed.
● Title, Artist and Album name are displayed if they are
recorded on the disc.
● In case of playback with the folder mode on, press
the PRESET ( or ) button, and the folder can be
selected even though it is in playback/pause mode.
It will continue playback/pause mode in the 1st track
of the selected folder.
● Display content can be changed by pressing the
DISPLAY button.
2 Press the PRESET (
or
) button on the
remote control to select
the desired folder.
Then press the Numeric
buttons on the remote
control to select the
desired tracks.
Note: To select track number 10 or higher, refer
’Direct track search’.
File name display
Folder display
3 Repeat step 2 for other folder/tracks. Up to 32 tracks
can be programmed.
4 Press the
/ (CD
Counter display
/ ) button to start playback.
Album display
Title display
Artist display
Note:
If “Not Support” is displayed, it means “Copyright protected
WMA file” or “Not supported playback file” is selected.
E-8
Listening to USB mass storage device/MP3 player
Caution:
At USB mode, once the iPod or iPhone is docked onto the
unit, the iPod or iPhone will automatically start charging.
‘iPod DOCK Charge Mode’ will be displayed. In order to
listen to any USB mass storage device / MP3 player, the
iPod or iPhone must be removed from the docking station.
Notes:
1. Remove the USB terminal cover
before use. Keep it away from
children as it may be swallowed.
2. Cover the USB terminal if it is not
used for a long period of time to
prevent dust or rust.
■
To play back USB/MP3 player with folder
mode on
1 Press the CD/USB button on the remote control or
FUNCTION button repeatedly on main unit to select
USB function. Connect the USB memory device that
has MP3/WMA format files on the unit. When the USB
memory is connected to the main unit, the device
information will be displayed.
2 Press the FOLDER button, and press the PRESET
( or ) button to select desired playback folder. To
start playback with folder mode on, go to step 4. To
change the playback folder, press the PRESET
( or ) button to select another folder.
3 Select desired file to be played back by pressing the
or
button.
4 Press the / (USB / ) button. Playback will start and
the file name will be displayed.
● Title, Artist and Album name are displayed if they are
recorded in the USB memory device.
● Display content can be changed by pressing the
DISPLAY button.
■
To remove USB memory device
1 Press the
(USB
) button to stop playback.
2 Disconnect USB memory device from the USB terminal.
Note:
This product is not compatible with MTP and AAC file
systems from USB mass storage device or MP3 player.
■
To play back USB/MP3 player with folder
mode off
1 Press the CD/USB button on the remote control or
FUNCTION button repeatedly on main unit to select
USB function. Connect the USB memory device that
has MP3/WMA format files on the unit. When the USB
memory is connected to the main unit, the device
information will be displayed.
2 Select desired file to be played back by pressing the
or
button.
3 Press the
/ (USB / ) button. Playback will start
and the file name will be displayed.
● Title, Artist and Album name are displayed if they are
recorded in the USB memory device.
● Display content can be changed by pressing the
DISPLAY button.
Note:
To pause playback:
Press the / (USB
/ ) button.
E-9
Notes:
● SHARP will not be held liable for the loss of data while
the USB memory device is connected to the audio
system.
● Files compressed in MP3 and/or WMA format can be
played back when connected to the USB terminal.
● This USB memory’s format supports FAT 16 or FAT 32.
● SHARP cannot guarantee that all USB memory
devices will work on this audio system.
● USB cable is not recommended for use in this audio
system to connect to USB memory device. Use of the
USB cable will affect the performance of this audio
system. iPod, iPhone and iPad is not prone to this
condition.
● This USB memory cannot be operated via USB hub.
● The USB terminal in this unit is not intended for a PC
connection but is used for music streaming with a USB
memory device.
● External HDD-storage cannot be played back via USB
terminal.
● If the data inside the USB memory is large, it may take
longer time for the data to be read.
● This product can play WMA and MP3 files. It will
automatically detect the file type being played. If
unplayable file is played on this product, “Not Support”
is indicated and the file will be automatically skipped.
This will take a few seconds. If abnormal indications
appear on the display due to the unspecified file, turn
off the unit and then turn it on again.
● This product relates to USB mass storage devices and
MP3 players. It may however face some irregularities due
to various unforeseen reasons from some devices. Should
this happen, turn off the unit and then turn it on again.
● During CD function, MP3 player will not be charging.
Advanced USB playback
The following functions are the same as CD
operations:
Page
Direct track search . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Repeat play. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Random play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Programmed play (MP3/WMA) . . . . . . . . . . . . . . . . . . . 8
Note:
● If USB memory device is not connected, “USB No
Media” will be shown on the display.
Notes:
● This unit only supports “MPEG-1 Audio Layer-3”
format. (Sampling Frequency is 32, 44.1, 48kHz)
● Playback order for MP3 files may differ depending on
the writing software used during file download.
● Bitrate which is supported by MP3 is 32~320 kbps,
WMA is 64~160 kbps.
● For MP3/WMA files, please put “.MP3” “.WMA”
extension. Files cannot be played back if there is no
MP3/WMA extension.
● Playlists are not supported on this unit.
● This unit can display Folder Name or File Name up to
32 characters.
● Maximum total number of MP3/WMA files is 65025.
● Total number of folders read is 999 including folder with
non-playable file. However, the display shows only
folder with MP3 files.
● The display playback time may not be displayed
correctly when playing back a variable bitrate file.
● The ID3TAG information supported are TITLE, ARTIST
and ALBUM only. Title name, artist name and album
name can be displayed by pressing the DISPLAY
button during file playback or pause mode.
● WMA meta tag also supports title, artist and album
name which are recorded in WMA files. Copyright
protected WMA files cannot be played back.
Listening to the radio
● Auto tuning:
When the TUNING ( or
) button is pressed for
more than 0.5 seconds, scanning will start
automatically and the tuner will stop at the first
receivable broadcast station.
Notes:
● When radio interference occurs, auto scan tuning may
stop automatically at that point.
● Auto scan tuning will skip weak signal stations.
● To stop the auto tuning, press the TUNING ( or
)
button again.
To receive an FM stereo transmission:
● Press the TUNER button to select stereo mode and
“ST” indicator will be displayed. “
” and “ ” will
appear when an FM broadcast is in stereo.
● If the FM reception is weak, press the TUNER button to
extinguish the “ST” indicator. The reception changes to
monaural, and the sound becomes clearer.
■
Memorizing a station
You can store 40 AM and FM stations in memory and recall
them at the push of a button. (Preset tuning)
1 Perform steps 2 - 3 in “Tuning”.
2 Press the MEMORY
button.
3 Within 30 seconds, press the PRESET (
or ) button
to select the preset channel number. Store the stations
in memory, in order, starting with preset channel 1.
4 Within 30 seconds, press the MEMORY button to store
that station in memory. If the “MEMORY” and preset
number indicators disappear before the station is
memorized, repeat the operation from step 2.
5 Repeat steps 1 - 4 to set other stations, or to change a
preset station. When a new station is stored in the
memory, the station previously memorized for that
preset channel number will be erased.
Note:
The backup function protects the memorized stations for a
few hours should there be a power failure or the AC power
cord becomes disconnected.
■
To recall a memorized station
Press the PRESET ( or
) button for less than 0.5
seconds to select the desired station.
■
To scan the preset stations
The stations saved in the memory can be scanned
automatically. (Preset memory scan)
1 Press the PRESET (
or
) button for more than 0.5
seconds. The preset number will flash and the programmed
stations will be tuned in sequentially, for 5 seconds each.
2 Press the PRESET (
or
) button again when the desired
station is located.
■
Tuning
■
1 Press the POWER ON/STAND-BY button to turn the power on.
2 Press the FUNCTION button on the main unit or
TUNER button on the remote control repeatedly to
select FM Stereo, FM Mono or AM.
To erase entire preset memory
1 Press the POWER ON/STAND-BY button to enter the stand-by mode.
2 While pressing down the
button, press the POWER ON/
STAND-BY button until “Tuner Clear” appears.
3 Press the TUNING (
or
) button on the remote
control to tune in to the desired station.
● Manual tuning:
Press the TUNING (
or
) button repeatedly to
tune in to the desired station.
E-10
TUNING
POWER
Setting the clock (Remote control only)
Timer and sleep operation (Remote
control only)
Timer playback:
The unit turns on and plays the desired source (CD,
TUNER, USB, iPod, AUDIO IN) at a preset time.
This unit has 2 types of timer: ONCE TIMER and DAILY
TIMER.
Once timer (“ ” indicator):
Once timer play works for one time only at a preset time.
In this example, the clock is set for the 24-hour (0:00) display.
1 Press the POWER ON/STAND-BY button to turn the power on.
2 Press the CLOCK/TIMER button.
3 Within 5 seconds, press the ENTER button. To adjust the
day, press the
or
button and then press the
ENTER button.
4 Press the
or
button to select 12-hour or 24-hour
display and then press the ENTER button.
Daily timer (“DAILY” indicator):
Daily timer play works at the same preset time every day
that we set. For example, set the timer as a wake-up call
every morning.
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio program,
and use the daily timer to wake up.
1 Set the daily timer.
2 Set the once timer.
1 minute or more
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
The 24-hour display will appear.
(0:00 - 23:59)
Start
■
or
button and then
press the ENTER button. Press the
or
button
once to advance the time by 1 hour. Hold it down to
advance continuously.
6 To adjust the minutes, press the
or
button and
then press the ENTER button. Press the
or
button once to advance the time by 1 minute. Hold it
down to advance the time by 5 minutes interval.
Note:
When power supply is restored after unit is plugged in again
or after a power failure, reset the clock.
To readjust the clock:
Perform “Setting the clock” from step 1. If the “Clock” does not
appear in step 2, step 4 (for selecting the 24-hour or 12-hour
display) will be skipped.
To change the 24-hour or 12-hour display:
1 Clear all the programmed contents. [Refer to “Factory
reset, clearing all memory” on page 14 for details.]
2 Perform “Setting the clock” from step 1 onwards.
Stop
Stop
Start
Timer playback
Before setting timer:
● Check that the clock is set to the correct time (refer to
this page). If it is not set, you cannot use the timer
function.
● For timer playback: Plug in USB or load discs or dock
iPod to be played.
5 To adjust the hour, press the
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Once timer
Daily timer
1 Press the POWER ON/STAND-BY button to turn the power on.
2 Press and hold the CLOCK/TIMER button.
3 Within 10 seconds, press the
or
button to
select “Once” or “Daily”, and press the ENTER button.
4 Within 10 seconds, press the
or
button to
select “Timer Set”, and press the ENTER button.
5 To select the timer playback source (CD, TUNER, USB,
iPod, AUDIO IN), press the
or
button. Press
the ENTER button.
When you select the tuner, select a station by pressing
the
or
button, and then press the ENTER
button. If a station has not been programmed, “No
Preset” will be displayed and timer setting will be
canceled.
6 To adjust the day, press the
or
button and then
press the ENTER button.
7 Press the ENTER button to adjust the hour. Press the
or
button and then press the ENTER button.
8 To adjust the minutes, press the
or
button and
then press the ENTER button.
9 Set the time to finish as in steps 7 and 8 above.
10 Adjust the volume using the VOLUME control, and then
press the ENTER button. Do not turn the volume up too
high.
E-11
Timer and sleep operation (Remote control only) (continued)
11 Press the POWER ON/STAND-BY button to enter the
power stand-by mode. The “TIMER” indicator lights up
and the unit is ready for timer playback.
■
Sleep operation
The radio, compact disc, iPod, USB, Audio In, Network can
all be turned off automatically.
1 Play back the desired sound source.
2 Press the SLEEP button.
3 Within 5 seconds, press the Numeric button to set the
12 When the preset time is reached, playback will start.
The volume will increase gradually until it reaches the
preset volume. The timer indicator will blink during
timer playback.
time. (1 minute ~ 99 minutes)
4 “SLEEP” will appear.
5 The unit will enter the power stand-by mode
automatically after the preset time has elapsed. The
volume will be turned down 1 minute before the sleep
operation finishes.
13 When the timer end time is reached, the system will
enter the power stand-by mode automatically.
Once timer:
The timer will be canceled.
Daily timer:
The timer operates at the same time every selected day.
It will continue until the daily timer setting is canceled.
Cancel the daily timer when it is not in use.
Notes:
● When performing timer playback using another unit
connected to the USB terminal or AUDIO IN jack, select
“USB” or “AUDIO IN” in step 5.
● This unit will turn on or enter the power stand-by mode
automatically. However, the connected unit will not turn
on or off. To stop the timer playback, follow step
“Cancelling the timer setting” of this page.
To confirm the remaining sleep time:
While “SLEEP” is indicated, press the SLEEP button.
To cancel the sleep operation:
Press the POWER ON/STAND-BY button while “SLEEP”
is indicated. To cancel the sleep operation without setting
the unit to the stand-by mode, proceed as follows.
1 While “SLEEP” is indicated, press the SLEEP button.
2 Within 5 seconds, press the “0” button twice until
“SLEEP 00” appears.
■
To use timer and sleep operation together
Checking the timer setting:
1 Turn the power on and press and hold down the
CLOCK/TIMER button.
Sleep and timer playback:
For example, you can fall asleep listening to the radio and
wake up to CD in the next morning.
2 Within 10 seconds, press the
1 Set the sleep time (see above, steps 1 - 5).
3 Within 10 seconds, press the
2 While the sleep timer is set, set the timer playback
or
button to select
“Once” or “Daily”, and press the ENTER button.
or
button to select
“Timer Call”, and press the ENTER button.
(steps 2 - 9, page 11).
Cancelling the timer setting:
1 Turn the power on and press and hold down the
CLOCK/TIMER button.
1-99 minutes
2 Within 10 seconds, press the
or
button to select
“Once” or “Daily”, and press the ENTER button.
or
button to select
“Timer Off”, and press the ENTER button. Timer will be
canceled (the setting will not be canceled).
1 Turn the power on and press and hold down the
End
time
Desired time
Sleep operation will
automatically stop
3 Within 10 seconds, press the
Reusing the memorized timer setting:
The timer setting will be memorized once it is entered. To
reuse the same setting, perform the following operations.
Timer playback
setting
Sleep timer
setting
Timer playback
start time
Enhancing your system
The connection cord is not included. Purchase a
commercially available cord as shown below.
CLOCK/TIMER button.
2 Within 10 seconds, press the
or
button to select
“Once” or “Daily”, and press the ENTER button.
3 Within 10 seconds, press the
or
button to select
“Timer On” , and press the ENTER button.
4 Press the POWER ON/STAND-BY button to enter the
power stand-by mode.
Portable audio
player, etc.
E-12
Audio cord (sold separately)
Enhancing your system (continued)
Troubleshooting chart (continued)
■
■
Listening to the playback sounds of
portable audio player, etc.
Symptom
1 Use a connection cord to connect the portable audio
player etc. to the AUDIO IN jack. When using video
equipment, connect the audio output to this unit and the
video output to a television.
2 Press the POWER ON/STAND-BY button to turn the power on.
3 Press the AUDIO IN button on the remote control or
FUNCTION button repeatedly on main unit to select
AUDIO IN function.
4 Play the connected equipment. If volume level of the
connected device is too high, sound distortion may
occur. Should this happen, lower the volume of the
connected device. If volume level is too low, increase the
volume of the connected device.
Note:
To prevent noise interference, place the unit away from the television.
■
Headphones
● Do not turn the volume on to full at switch on and listen to
music at moderate levels. Excessive sound pressure from
earphones and headphones can cause hearing loss.
● Be sure your headphone has a 1/8" (3.5 mm) diameter plug
and impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
● Before plugging in or unplugging the headphone, reduce the
volume.
● Plugging in the headphone disconnects the speakers
automatically. Adjust the volume using the VOLUME control.
Troubleshooting chart
Many potential problems can be resolved by the owner without
calling a service technician.
If something is wrong with this product, check the following before
calling your authorised SHARP dealer or service centre.
■
General
Symptom
Possible cause
● The clock is not set to
the correct time.
● Did a power failure occur?
Reset the clock. (Refer page
11)
● When a button is
pressed, the unit does
not respond.
● Set the unit to the power standby mode and then turn it back
on.
● If the unit still malfunctions,
reset it. (Refer page 14)
● No sound is heard.
● Is the volume level set to “Min”?
● Are the headphones
connected?
■
● The remote control
does not operate.
■
Symptom
● The radio makes
unusual noises
continuously.
■
● Is the disc loaded face
down?
● Does the disc satisfy the
standards?
● Is the disc distorted or
scratched?
● Playback sounds are
skipped, or stopped
in the middle of a
track.
● Is the unit located near
excessive vibrations?
● Is the disc very dirty?
● Has condensation formed
inside the unit?
Possible cause
● Is the unit placed near the
TV or computer?
● Is the FM antenna placed
properly? Move the antenna
away from the AC power
cord if it is located nearby.
USB
Symptom
● Device cannot be
detected.
Possible cause
● Is there any MP3/WMA file
available?
● Is the device properly
connected?
● Is it an MTP device?
● Does the device contain
AAC file only?
● Playback does not ● Is it a copyright protected
start.
WMA file?
● Is it a false MP3 file?
● Wrong time display. ● Is Variable Bitrate file being
played back?
● Wrong file name
display.
● Is the File Name written in
Chinese or Japanese
characters?
■
iPod, iPhone or iPad
Symptom
● No sound is
produced.
Possible cause
● Playback does not
start.
● Playback stops in
the middle or is not
performed properly.
Possible cause
● Is the AC power cord of the
unit plugged in?
● Is the battery polarity
correct?
● Is the battery dead?
● Is the distance or angle
incorrect?
● Does the remote control
sensor receive strong light?
Tuner
● iPod, iPhone or iPad
will not charge.
CD player
Symptom
Remote control
● “This accessory is
not made to work
with iPhone” or
“This accessory is
not supported by
iPhone” appears on
iPhone screen.
E-13
Possible cause
● The iPod, iPhone or iPad is
not playing.
● The iPod, iPhone or iPad is
not properly connected to the
unit.
● Is the AC power cord of the
unit plugged in?
● The iPod, iPhone or iPad is
not making full contact with
the connector.
● Using iPod (3rd generation).
● The iPod or iPhone is not
supported. Refer to page 5 for
compatible models.
● The iPhone battery is low.
Please charge the iPhone.
● iPhone is not properly
docked.
Troubleshooting chart (continued)
■
■
Wi-Fi connection
Symptom
● Wi-Fi network
connection failed.
■
Possible cause
● Is your router Wi-Fi certified?
● WPS-Pin and WPS-PBC
routers is not supported by
this unit.
● Is the SSID broadcast on the
Wi-Fi router enabled?
● Avoid using Wi-Fi channel
which is much overlapped by
the nearby Wi-Fi network.
● Is the unit placed near a
potential source of
interference which may affect
Wi-Fi signal, such as
microwave ovens?
● Is your PC using a Wi-Fi
network? Ethernet connection
for AirPlay / DLNA network
setup is not possible.
● Do not use special characters
like ‘%, #, *’ to rename your
router or the AirPlay device in
the setting menu.
●
●
● Breaking of music
streaming.
●
●
●
●
●
●
Possible cause
Is the unit joined to the AirPlay
network?
Is the Bonjour service in your
PC enabled before you open
iTunes?
Firewalls and security software
must be disabled.
Is your network speed fast
enough? Other devices
connected to your home router
might need to be turned off.
Restart your Apple AirPlay /
DLNA device or this unit.
Stop any internet content
browsing via your home router.
Enable the Auto Channel Scan
Option on the Wi-Fi router if
available.
Enable the Wireless Intelligent
Stream Handling (WISH)
option on the Wi-Fi router if
available.
Enable the Quality of Service
(QoS) option on the Wi-Fi
router if available.
Other home routers must be
turned off.
Network reset
If the Network function operates incorrectly, do the reset
operation as below:
During Network function, press and hold CLEAR button
until “Network Clear” appears.
This operation will erase the current Wi-Fi setting.
If problem occurs
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on
again.
2 If the unit is not restored in the previous operation,
unplug and plug in the unit again, and then turn the
power on.
Note:
If neither operation above restores the unit, clear all the
memory by resetting it.
■
● AirPlay connection
●
failed with Mac or PC.
●
■
■
When this product is subjected to strong external
interference (mechanical shock, excessive static
electricity, abnormal supply voltage due to lightning, etc.)
or if it is operated incorrectly, it may malfunction.
AirPlay / DLNA
Symptom
● No AirPlay icon on
Apple AirPlay device
or iTunes in my PC.
Condensation
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet (CD pickup, etc.) or on the transmitter on
the remote control. Condensation can cause the unit to
malfunction. If this happens, leave the power on with no
disc in the unit until normal playback is possible (about 1
hour). Wipe off any condensation on the transmitter with a
soft cloth before operating the unit.
Factory reset, clearing all memory
1 Press the POWER ON/STAND-BY button to enter the
power stand-by mode.
2 While pressing down the OPEN/CLOSE button, press the
POWER ON/STAND-BY button until “Clear All” appears.
POWER
Caution:
This operation will erase all data stored in memory
including clock, timer settings and tuner preset.
■
Before transporting the unit
Remove the iPod, iPhone, iPad, USB memory device and disc
from the unit. Then, set the unit to the power stand-by mode.
Carrying the unit with iPod, iPhone, iPad or USB memory
device left connected or discs left inside might damage the unit.
■
Care of compact discs
Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on the
disc surface. Follow the guidelines below for maximum
enjoyment from your CD collection and player.
● Do not write on either side of the disc, particularly the
non-label side from which signals are read. Do not
mark this surface.
● Keep your discs away from direct sunlight, heat, and
excessive moisture.
● Always hold the CDs by the edges. Fingerprints, dirt, or
water on the CDs can cause noise or mistracking. If a CD
is dirty or does not play properly, clean it with a soft, dry
cloth, wiping straight out from the centre, along the radius.
YES
NO
Correct
E-14
Maintenance
■
Cleaning the cabinet
Periodically wipe the cabinet with a soft cloth and a diluted
soap solution, then with a dry cloth.
Caution:
● Do not use chemicals for cleaning (gasoline, paint
thinner, etc.). It may damage the cabinet.
● Do not apply oil to the inside of the unit. It may cause
malfunctions.
Specifications
As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of
production units. There may be some deviations from these values in individual units.
■
■
General
Power source
AC 120 ~ 60 Hz
Power
consumption
Power on: 26 W
Speaker
1-way speaker system
Speaker: 2-1/2" (6.5 cm)
Speaker
maximum input
power
50 W/channel
Speaker rated
input power
25 W/channel
Dimensions
Width: 18 - 11/16" (475 mm)
Height: 7 - 1/2" (191 mm)
Depth: 3 - 1/4" (83 mm)
Weight
5.9 lbs. (2.7 kg)
■
Amplifier
Output power
RMS: Total 50 W (25 W per channel
into 6 ohms at 1 kHz, 10%
T.H.D.)
FTC: 22 W minimum RMS per
channel into 6 ohms from
100 Hz to 20 kHz, 10% T.H.D.
Output terminals Headphones: 16 ohms
(recommended: 32 ohms)
Input terminals
■
Audio In (audio signal):
500 mV/47 k ohms
USB host interface ● Complies with USB 1.1 (Full
Speed)/2.0 Mass Storage
Class.
● Support Bulk only and CBI
protocol.
Support file
● MPEG 1 Layer 3
● WMA (Non DRM)
Bitrate support
● MP3 (32 ~ 320 kbps)
● WMA (64 ~ 160 kbps)
Other
● Maximum total number of
MP3/WMA files is 65025.
● Maximum total number of
folders is 999 INCLUSIVE of
root directory.
● The ID3TAG information
supported are TITLE, ARTIST
and ALBUM only.
● Supports ID3TAG version 1
and version 2.
File system
● Support USB devices with
Microsoft Windows/DOS/FAT
support
12/FAT 16/ FAT 32.
● 2 kbyte block length for sector.
■
Single disc multi-play compact disc
player
Signal readout
Non-contact, 3-beam
semiconductor laser pickup
D/A converter
Multi bit D/A converter
Frequency
response
20 - 20,000 Hz
Dynamic range
90 dB (1 kHz)
Tuner
Frequency range
FM: 87.5 - 108.0 MHz
AM: 530 - 1,710 kHz
Preset
40 (FM and AM station)
CD player
Type
USB (MP3 / WMA)
E-15