CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • INTAKE
R&D PERFORMANCE
POWER PLENUM AIR
FILTER KIT
The R&D High Performance Power
Plenum Air Filter Kit was designed,
developed and dyno tested exclusively
for the new Yamaha SHO/FZR supercharged intake system to unleash
low-end, mid-range, and peak horsepower trapped in the restrictive stock
air box. The exclusive lightweight filter
design couples to the OEM supercharger hose and is engineered with a large
6”x10”x6” plenum to deliver massive
cubic air volume and improved air speed
to the supercharger. Replacing the
O.E.M. air box with the R&D Filter kit
offers an economical way to improve performance, looks, and sound at a
fraction of the cost of other aftermarket kits. Kit comes complete with all
necessary hardware and installs in minutes.
Description
Part No.
R&D FX-SHO/FZR/FZS
Performance Power Plenum Air Filter Kit
R&D VXR/VXS POWER
PLENUM FILTER KIT
The R&D High Performance Power Plenum
Air Filter Kit was designed and developed
exclusively for the new Yamaha 1.8 liter
N.A. engine. The R&D filter kit will unleash
low-end, mid-range, and peak horsepower
trapped in the restrictive stock air box. The
exclusive lightweight filter design couples to
the OEM throttle body through a tuned built
in velocity stack. The engineered oversized
Tear Drop plenum, delivers the velocity
and cubic air volume needed to add power.
Power Plenum Filters generate the
maximum airflow and volume. Performs
well, sounds good, looks great, and will install in minutes. Kit comes
complete with all necessary hardware.
Description
R&D VXR/VXS Power Plenum Filter Kit
Part No.
200-01805
R&D FX-SHO/FZR/FZS
POWER PLENUM
FLAME ARRESTER
FOR STOCK AIR BOX
The R&D High Flow Filter design
replaces the restrictive stock filter
inside the stock air box, allowing improved air flow. Why? Because more air
flow means more power and improved performance. The washable and
reusable design means this will be the last filter you will ever have to buy.
Description
R&D FX-SHO/FZR/FZS / VXR / VXS
Power Plenum Flame Arrester
26
200-01801
Part No.
200-01800
SHO/FZR/FZS PRO COMP
COOL AIR FILTER KIT
The system is designed and tested with
boost levels above 23 pounds and speeds
of 92+ MPH. The R&D System utilizes an
oversized specifically designed 7.250” x
5.500” x 6” teardrop shaped R&D Power
Plenum Filter w/crankcase vent that rubber
mounts in the space over the top left side
of the gas tank. The system ducts its air
supply to the supercharger via an “Indy
Car style” 3.5” mandrel bent Aluminum tube
and couples to the supercharger with a 90°
Nomex tapered reduction elbow. Power
Plenum Filters generate the maximum airflow and volume and install in minutes. Recommended for the R&D C1, C3, C5, C20X and C23X Monster
Supercharger Wheel kits and Superchargers. This system will also couple to
the soon to be released R&D Cool Charger Housing, a 100% water-cooled
supercharger Housing.
Description
SHO/FZR/FZS Pro Comp Cool Air Filter Kit
Part No.
200-01802
OEM
FOR INTAKE
MANIFOLD
FOR INTERCOOLER
R&D
R&D SHO POWER CORE INTAKE
MANIFOLD/INTERCOOLER CFM KIT
The R&D FX-SHO/FZR/FZS Power Intake Manifold and Intercooler CFM Kit
was developed to increase airflow into and through the intake system by
relieving restrictions. The R&D FX-SHO/FZR/FZS intake manifold ribbon
remover sleeve will unlock a 40 CFM (cubic feet per minute) air flow restriction by replacing the intake manifold ribbon with the R&D billet venturi sleeve.
The R&D Intercooler Spacer will unlock a 30-35 CFM restriction in the intercooler. The R&D FX-SHO/FZR/FZS Intake Kit will add low end and mid range
throttle response, and a full 100 plus rpms to top end performance to a stock
FX-SHO/FZR/FZS. The R&D FX-SHO/FZR/FZS Intake Kit is an absolute must
have parts kit to remove intake restrictions before contemplating power
adding compressor booster wheels or turbo charger kits to the FXSHO/FZR/FZS engine. True horsepower gains on the FX-SHO/FZR/FZS start
right here with the R&D Intake Kit. More airflow will equal more power, and
there is no other way around the fact that restricted is restricted power.
Description
Part No.
R&D FX-SHO/FZR/FZS Power Core Billet Intake
612-18000
Manifold Sleeve & Intercooler Spacer CFM Kit
R&D Power Core Intake Manifold Sleeve Only
612-17998
R&D FX-SHO/FZR/FZS Intercooler CFM Spacer Only 612-17999
YAMAHA FX-SHO/FZ/VXR/VXS • INTAKE • SUPERCHARGER
YAMAHA
4 STROKE
INATKE
SYSTEMS
RIVA VXR/VXS POWER FILTER KIT
RIVA PERFORMANCE YAMAHA
FX-SHO/FZR/FZS POWER FILTER KIT
Description
Part No.
Part No.
RY13060
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
The Riva Power Filter feeds your SHO or FZR a steady diet of cool air
delivering greatly improved acceleration and rpm. Replaces restrictive stock air
box with a high-volume, precision-formed intake duct that attaches to
the supercharger via a large 4” adapter. Cool air enters the system via an
oversized K&N filter element. Includes water-repellent pre-filter.
Riva FX-SHO/FZR/FZS Performance Power Filter Kit RY13040
Description
RIVA VXR/VXS Power Filter Kit
EXHAUST
Key Features:
• Delivers increased acceleration & top speed.
• True "cold air" system utilizes OEM hood scoop.
• Ultra-dry water trap keeps water out of system.
• Genuine screen type K&N Flame Arrestor & water repellent prefilter cover.
• Large 4" smooth-bore ducting attaches to engine via flow-matched velocity
stack.
• Includes updated crankcase breather system for improved performance.
ENGINE/
GASKETS
Our VXR/VXS Power Filter is a true "cold air" intake system that draws cool
air from outside your engine compartment delivering significant performance
gains. Utilizes OEM hood scoop to feed air into an ultra-dry water trap system for reliable operation in rough water conditions. Cold air is delivered to
engine via large 4" smooth-bore ducting that is secured to throttle body with
unique velocity stack and sturdy billet clamps. Kit also includes an improved
breather system that keeps hot oil vapor and crankcase fumes from entering
your engine's air intake.
BODY
Our Intake Manifold Upgrade Kit enables your 1.8L naturally aspirated
engine to produce more horsepower by delivering increased air flow.
Precision tapered billet sleeve directly replaces restrictive mesh element
in intake manifold. Provides improved low end punch and mid range pull
through quick & easy installation. Includes detailed installation instructions.
NOTE: Our testing has determined the stock ECU will compensate for the
increased air flow provided by our Intake Manifold Upgrade Kit. Requires
RIVA Power Filter Kit to meet U.S. Coast Guard certified flame arrestor
requirements.
IJSBA Stock Class Legal.
Description
RIVA Yamaha 1.8L Engine Intake Manifold
Upgrade Kit
RIVA FX-SHO/FZR/FZS INTAKE
MANIFOLD UPGRADE KIT
Our Intake Manifold Upgrade Kit enables your SHO engine to produce more
horsepower by delivering increased air flow and boost pressure (+1lb).
Precision tapered billet sleeve directly replaces restrictive mesh element in
intake manifold. Provides improved low end punch and mid range pull through
quick & easy installation. Includes detailed installation instructions.
NOTE: Testing has determined the stock ECU will compensate for the
increased boost provided by our Intake Manifold Upgrade Kit.
Description
Part No.
RY12055-IMUK
Riva FX-SHO/FZR/FZS
Intake Manifold Upgrade Kit
Part No.
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
RIVA YAMAHA 1.8L ENGINE INTAKE
MANIFOLD UPGRADE KIT
RY12040-IMUK
27
YAMAHA FX-SHO & FZ • SUPERCHARGER
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
R&D FX-SHO/FZR/FZS C1
MONSTER CHARGER WHEEL
R&D’s new C1 11 Blade Series Monster
Compressor Wheel Kit for Yamaha SHO/FZS/FZR
engines is new and improved to deliver “horsepower you can feel” with instant throttle response,
improved mid range acceleration, and increased top end performance. The
R&D Monster Wheel replaces the stock wheels inefficient 5 blade design with
an all new modern low profile, high flow, 11 blade high tech design. Fits directly
into the O.E.M. stock compressor housing with no modifications. The C1-11
Monster works with the OEM intercooler, OEM fuel injectors, OEM ignition
system and the R&D Intake CFM Kit. Kit performs well on 91 octane pump
gasoline. Boost rated 7/8.5 P.S.I. (7 @ 7500 and 8.5 @ 7700) Horsepower
increases were professionally documented by MOTEC AUSTRALIA.
• Increased boost pressure ( 3-3.5 over stock @ 7700 rpm)
• Increased airflow (1.5-2 pound per minute gain)
• 25-30 Horsepower increase and 2 MPH Gain (with OEM ignition)
• 70 Horsepower increase (with Motec ECU, CFM kit, 91 pump gas)
• Precision balanced (turbo specs .012-.027 gram inches)
• Better throttle response, increased horsepower • Ultra easy installation
• 91 octane pump gas friendly • Inexpensive horsepower upgrade
The C1 Wheel Kit works excellent for recreational use applications retaining the
OEM ignition, fuel system, injectors, and intercooler. R&D has data logged and
documented the A.F.R. (air to fuel ratio) to be a conservative and safe 11.8-12.0
with the C1 wheel kit. R&D recommends that the R&D Power Core Intake
Manifold and intercooler CFM kit or the R&D Stage 1 Intercooler Kit be used
with the C1 wheel.
Description
Part No.
R&D FX-SHO/FZR/FZS C1 Monster Charger Wheel
612-25001
R&D FX-SHO/FZR/FZS C3
MONSTER CHARGER WHEEL
R&D’s new C3-11 Blade Series Racing Monster
Compressor Wheel Kit for Yamaha SHO/FZS/FZR
engines is an exciting new racing product that will
deliver “horsepower you can feel” with instant throttle
response, aggressively improved low and mid range
acceleration, and increased top end performance.
The R&D Monster Wheel replaces the stock wheels
low performing 5 blade design with a modern low profile, high flow 11 blade high
tech design with a larger exducer diameter to move more air flow at lower rpm’s
producing better holeshot horsepower. The R&D C3 Monster Wheel and R&D
Exducer Seal Plate Kit will install directly into the O.E.M. stock compressor
housing with no modifications. The C3 Racing Monster will require the R&D High
Performance Intercooler Kit, and an R&D Impellor upgrade. The C3-11 performs
well on 91 octane pump gasoline. Boost rated 10/13 P.S.I. (10 @ 7700 and
13@8300) The new R&D 11 blade series compressor wheels offer the highest
levels of airflow and horsepower gains available for the 1.8 Yamaha engine using
the stock E.C.U.
• Increased boost pressure ( 5 P.S.I. over stock @ 7700 rpm)
• Increased airflow ( 2.5-3 pound per minute gain)
• 35+ Horsepower increase and 2 MPH Gain (with stock ECU)
• 300+ Horsepower using aftermarket ECU (MOTEC)
• Precision balanced (turbo specs .012-.027 gram inches)
• Utilizes O.E.M. ignition system with R&D Impellor Upgrade
• Utilizes O.E.M. fuel injectors • 91 octane pump gas friendly
R&D FX-SHO/FZR/FZS C3 Monster Charger Wheel
The new “drop-in” R&D C5 Monster
Compressor Wheel and Exducer Seal Plate Kit installs directly into the OEM
supercharger without any modification. The new C5 delivers “horsepower you
can feel” with instant throttle response, aggressively improved low and mid
range acceleration, and intensified top end performance. The new C5 features
a light weight, high flow, 8 blade design with 8 supporting splitter veins and an
increased exducer diameter over stock. R&D’s large exducer diameter and
aggressive blade design is the key to improving CFM airflow volume throughout
the RPM range. The oversized exducer diameter increases the size of the
supercharger by enhancing air pumping volume and efficiency. The C5 out
performs any OEM sized compressor wheel in its boost pressure classification.
After all, its airflow volume gains that increase horsepower.
The R&D Monster Wheel Kit produces 14-15 pound per minute airflow gain
with a solid 15-16 pounds of boost pressure @ 8400-8500 rpm, 17+ @ 87008800 rpm. The new drop-in R&D C5 also offers superior off throttle surge
reduction over other 15-16 pound boost wheels. The new R&D C5 series
compressor wheels offer the highest levels of airflow and horsepower gains
available for the 1.8L Yamaha engine in the 15-17 pound boost range. A
properly tuned C5 set up (with supporting modifications) can produce well over
325 horsepower. In addition, no other rotating group on the market is lighter or
more powerful than the new C5 Monster Wheel combined with the R&D Billet
Supercharger Shaft.
In sum, the R&D C5 Monster Wheel and Shaft weighs less, has less surge,
rockets to 80 in less seconds and carves through corners in less time than any
other wheel and shaft in its class. Hit the throttle, hang on and discover the
astounding sensation that’s called Power!
• Aggressive throttle response, increased horsepower
• Increased boost pressure ( 10 P.S.I. over stock @ 8500 rpm)
• Increased airflow volume ( 14-15 pound per minute gain)
• 100+ horsepower increase (with R&D R3 ECU)
• 325+ horsepower using aftermarket ECU
• Precision balanced (turbo specs .012-.027 gram inches)
• Utilizes O.E.M. Reprogrammed R3 ECU ignition system
• Utilizes O.E.M. fuel injectors w/R&D RRFPR, R3, and Powershot
• 91 octane pump gas friendly with R3 ECU
• Less weight and surge
• Easy installation
C5 Modification Requirements:
R&D High Performance Pro Series Intercooler Kit w/R&D Greddy BOV
R&D Rising Rate Fuel Pressure Regulator Kit
R&D R3 ECU upgrade to allow 8500-8850 RPM
R&D Powershot
R&D Engine/intercooler Cooling Kit
R&D Twin Prop
NOTE: The C5 Monster Wheel will work best in sea level to 2000 ft. elevations,
or in ambient air temperatures between 60 and 100 degrees. NOTE: The C5
Monster Wheel Kit will require serious
impellor upgrades.
NOTE: The C3 Monster Wheel Kit will require impellor upgrades over the C1
impellor suggestions.
Description
Part No.
28
R&D SHO/FZR/FZS
C5 MONSTER
CHARGER WHEEL
612-25003
Description
SHO/FZR/FZS C5 Monster Charger Wheel
Part No.
612-25005
YAMAHA FX-SHO & FZ • SUPERCHARGER
FX-SHO/FZR/FZS
C20X MONSTER WHEEL
Boost rating: 12 @ 7800, 15/16 @ 8400-8500, 17 @ 8700-8800, 18 @ 92009500).
NOTE: The C8 Monster Wheel will work best in sea level to 2000 ft. elevations,
or in ambient air temperatures between 60 and 100 degrees. NOTE: The C5
Monster Wheel Kit will require serious impellor upgrades.
Description
FZR C8 Monster Charger Wheel
Part No.
612-25008
NOTE: The R&D C20X Monster Compressor Wheel delivers a 17.5-18.5 pound
per minute airflow gain (approximately 150 plus horsepower at sea level at
8500 rpm’s). Pound per air volume gain is based on the rate of 1 pound of air
gain per minute for every 8-10 H.P. gain. The C20X Monster Wheel will work
best in sea level to 2000 ft. elevations, or in ambient air temperatures between
60 and 100 degrees. R&D strongly suggests that the R&D High Performance
Racing Intercooler Kit, Aftermarket ECU, R&D RRFPR be installed with the
C20X Kit. Trust the pros at R&D to boost up your airflow volume, after all, its airflow volume gains that increase horsepower. NOTE: The C20X Monster Wheel
Kit requires serious impellor up grades.
Description
C20X Monster Wheel And Exducer Kit Only
C20X Monster Wheel And Exducer Kit with
Machining Service to your Front Housing
Watercooled Supercharger Cover for C20X
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
C8 Modification Requirements:
R&D High Performance Pro Series Intercooler Kit w/R&D GReddy BOV
R&D Rising Rate Fuel Pressure Regulator Kit
R&D R3 ECU upgrade to allow 8500-8850 RPM
R&D Powershot
R&D Engine/intercooler Cooling Kit
R&D Twin Prop
• Aggressive throttle response, increased horsepower
• Increased boost pressure ( +12 P.S.I. over stock @ 8700 rpm)
• Increased airflow ( 17.5-18.5 pound per minute gain)
• 150-175 horsepower increase
• Aftermarket ECU REQUIRED (MOTEC M400/ViPEC)
• Aftermarket R&D Fuel Injectors REQUIRED
• Aftermarket R&D RRFPR REQUIRED
• Precision balanced (turbo specs .012-.027 gram inches)
• Utilizes O.E.M. fuel injectors w/R&D RRFPR,R2 and Powershot
• VP C12 octane RACE gas friendly
• Easy installation
BODY
• Aggressive throttle response, increased horsepower
• Increased boost pressure ( 12 P.S.I. over stock @ 8800 rpm)
• Increased airflow volume ( 14-15 pound per minute gain)
• 100+ horsepower increase (with R&D R3 ECU)
• 350+ horsepower w/supporting parts
• Precision balanced (turbo specs .012-.027 gram inches)
• Utilizes O.E.M. Reprogrammed R3 ECU ignition system
• Utilizes O.E.M. fuel injectors w/R&D RRFPR, R3, and Powershot
• 91 octane pump gas friendly with R3 ECU
• Less weight and surge
• Easy installation
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Less is More
In sum, the R&D C8 Monster Wheel and Shaft weighs less, has far less surge
over competitors’ wheel kits, rockets to 80 in less seconds and carves through
corners in less time than any other wheel and shaft on the planet. Hit the
throttle, hang on and discover the astounding sensation that less IS more
…much, much more.
EXHAUST
The new R&D C8 series compressor wheels offer the highest levels of airflow
and horsepower gains available for the 1.8L Yamaha engine. A properly tuned
C8 set up (with supporting modifications) can produce well over 325+ horsepower. In addition, the rotating group of the new C8 Monster Wheel combined
with the R&D Billet Supercharger Shaft is the undisputed Light Weight Champ,
no other rotating group on the market is lighter or more powerful.
ENGINE/
GASKETS
The R&D Monster Wheel Kit produces 18 plus pounds of boost pressure @
8700-8900 rpm, 16+ @ 8500-8600 rpm. The new drop-in R&D C8 also offers
superior off throttle surge over other 16-18 pound boost wheels. Less surge
increases supercharger clutch reliability.
Twenty pounds of boost now available. R&D’s
leading the way in performance with the new
C20X Racing Monster Compressor Wheel Kit
for the Yamaha SHO, FZ, and FZR. The
C20X delivers arm stretching power like you
have never experienced. The C20X pumps
out 18 pounds of boost @ 8500-8700 rpm
and 20 pounds of boost @ 9000 rpm with a
17.5-18.5 pound per minute airflow gain
through its high flow 8 blade wheel design featuring oversized inducer and
exducer wheel diameters. R&D’s large inducer and exducer wheel diameters
along with an aggressive blade design are the key to improving CFM airflow
volume throughout the RPM range. The oversized inducer and exducer diameters increase the size of the supercharger by enhancing air pumping volume
and efficiency. After all, its airflow volume gains that increase horsepower. The
C20X Racing Monster wheel requires the R&D High Performance Pro Series
Intercooler Kit, R&D 1000cc Fuel Injectors, R&D Rising Rate Fuel Pressure
Regulator Kit, and an aftermarket ECU (MoTeC or ViPEC) upgrade to allow
proper engine tuning. R&D also suggests upgrading to R&D Forged Racing
Rods and Performance Pistons. The new R&D C20X is for Racing use only and
requires 110 octane racing fuel. Boost rated to 18 plus at 8500-8700 and 20
pounds at 9000. The new R&D C20X series compressor wheels offer the highest levels of airflow and horsepower gains available for the 1.8 Yamaha engine.
Aftermarket ignition systems and a C20X Monster properly tuned can achieve
up to 400 Horsepower.
The new C20X will require a shop service to bore out your compressor front
housing to except the larger C20X compressor wheel. For those customers that
have previously purchased the C5-11 and already have the shop service to the
compressor front housing, just order the C20X wheel kit and change out the
wheel. No other supercharger compressor wheel kit has stolen more holeshots
and won more National and Offshore Titles than the R&D Monster Wheel Kits.
If 20 pounds of boost is truly what you’re looking for, well look no further and
just give us a call. The new C20X has been tested against all other existing
wheels on the market and is guaranteed to blow them away!
INATKE
SYSTEMS
The new “drop-in” R&D C8 Monster
Compressor Wheel and Exducer Seal
Plate Kit installs directly into the OEM
supercharger without any modification.
The new C8 delivers “horsepower you
can feel” with instant throttle response,
aggressively improved low and mid range acceleration, and intensified top end
performance. The new C8 features a light weight, high flow, 8 blade design with
8 supporting splitter veins and an increased exducer compression height over
stock. R&D’s larger exducer height and aggressive blade design is the key to
improving CFM airflow volume throughout the RPM range. The increased
exducer height dimension increases the size of the supercharger by enhancing
air pumping volume and efficiency. The C8 out performs any OEM sized
compressor wheel in its boost pressure classification. After all, its airflow
volume gains that increase horsepower.
YAMAHA
4 STROKE
FX-SHO/FZR/FZS
C8 MONSTER WHEEL
Part No.
612-25006
612-25007
612-24001
29
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO & FZ • SUPERCHARGER
RIVA FX-SHO/FZR
SUPERCHARGER IMPELLERS
Riva Racing released the ultimate (drop-in) performance supercharger
impellers for the Yamaha 1.8 liter SHO Engine! Working closely with Vortech
Engineers, Riva designed these impellers to deliver more horsepower and
torque throughout the RPM range resulting in excellent acceleration and top
speed. Investment cast from an extremely strong, lightweight proprietary aluminum and CNC machined to ensure exact tolerances. All new blade design
is optimized aerodynamically and precision balanced to deliver smooth
operation. Installs easily into stock supercharger housing with no
modifications required. Includes detailed installation instructions.
B1 produces 11.5psi @ 7,700rpm • E1 produces 16psi @ 8,000rpm
NOTE: Both impellers require use of aftermarket engine management system
for proper calibration
Description
Riva FX-SHO/FZR S/C Impeller - 11.5 psi
Riva FX-SHO/FZR S/C Impeller - 16 psi
Ever wonder why the supercharger is so HOT? Heat is a derivative of
compressed air (boost). The more boost pressure, the hotter the supercharger
gets. The engineers at R&D understand the key in producing more horsepower
and maximizing performance, is managing heat.
R&D is proud to announce the new Water-Cooled Supercharger Housing
System. The new R&D Water-Cooled Supercharger System is fully water
jacketed and eliminates heat at its source, the Supercharger. The new system
replaces the OEM inducer cover and mounts directly to the OEM
Supercharger body.
The system features a High Performance Volute (intake air path), Internal
Anti-Surge Port, 100% Water-Cooling and a custom R&D Power Plenum Air
Filter. Now since the Supercharger is the coolest part in the engine compartment and runs at lake temperature, it only made since to design a custom
R&D Power Plenum Air Filter that would take full advantage of the new found
cool air, now located directly in front of the Supercharger.
System installs in 45 minutes and comes complete with all necessary
hardware and pictorial instructions.
RIVA FX-SHO/FZ 'H1' RACE CHARGER
IMPELLER & HOUSING
The 'H1' Race Charger was designed for serious racers and tuners who
demand the ultimate performance gains. H1 Impeller and housing combo
delivers 20psi of boost pressure at 8,500rpm producing up to 400hp on modified engines. High performance impeller and housing combo increase horsepower through superior blade design and larger interior housing volume.
Impeller features a sophisticated HKS blade design that is precision balanced
for smooth operation. Requires aftermarket ECU and upgraded engine components for proper calibration and durability.
Performance Benefits: Up to 200° F cooler supercharger temperature,
cooler and denser intake air, decreased engine compartment temperature,
improved clutch life through Internal Anti-Surge Port, increased RPM (up to
200 rpm), increased boost pressure, improved top speed, no heat fade,=
consistent peak engine rpm.
Fitment: The R&D Water-Cooled System fits all supercharger wheels that fit
into the OEM charger housing.
Description
612-24000
612-24001
R&D SUPERCHARGER
BLOCK-OFF PLATE
The R&D Supercharger Block-off
Plate is designed to seal the case
on the front of the engine that is
exposed when the supercharger is
removed for a Turbo.
Performance Data:
• 16.5psi @ 7,500rpm • 17psi @ 7,700rpm
• 18psi @ 8,000rpm • 20psi @ 8,500rpm
Part No.
RY17040-IH-H1
Part No.
SHO/FZR/FZS Water-Cooled OEM
Supercharger System for (C1, C3, C5)
SHO/FZR/FZS Water-Cooled
Supercharger System (For C20X)
FOR COMPETITION USE ONLY. RIVA Racing is not liable for possible
damage to associated parts or labor costs incurred due to the installation of
this racing component.
Description
RIVA FX-SHO/FZ 'H1' Race Charger
Impeller & Housing
30
Part No.
RY17040-SCI-B1
RY17040-SCI-E1
FZR WATER-COOLED
SUPERCHARGER SYSTEM
Description
R&D Supercharger Block-off Plate
Part No.
612-19100
YAMAHA FX-SHO & FZ • SUPERCHARGER
ENGINE-TECH FX-SHO/FZ
XTREME SERIES SC IMPELLER
Part No.
ETYAMHO
ENGINE-TECH YAMAHA FZR
SUPERCHARGER IMPELLER
Must be used with adjustable fuel regulator, high flow intercooler and ECU
(Motec or equiv, Motec map available upon request)
Description
Part No.
Engine-Tech FZR SC Impeller (18+ lbs)
A.
B.
ETYAMSHO
R&D SPECIALTY
SUPERCHARGER TOOLS
Lastly, R&D reduced the weight of the R&D Supercharger shaft by eliminating
the hex nut on rear the gear and lightened the end of the shaft/gear inside
diameter to significantly reduce reciprocating weight. We all know what that
will do to add to clutch performance. Kit comes complete with larger nut and
installation instructions. All in all, the new R&D High Performance Billet Racing
Shaft is not just a replacement shaft, but a solution to end all supercharger
shaft problems.
Description
Description
Riva Heavy-Duty SC Shaft Upgrade Kit
Part No.
RY17040-UK-6S5
Description
Part No.
OEM Replacement Bearing Kit (stock/limited class legal) 612-25025
Upgraded Supercharger Duplex Bearing Kit
612-25026
Supercharger Rebuild Kit with OEM
612-25028
Exducer/Thrust Bearing Assembly Kit
Supercharger Rebuild Kit with C3/C5
612-25030
Exducer/Thrust Bearing Assembly Kit
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Riva Heavy-duty Supercharger Shaft Upgrade Kit delivers increased strength
& reliability to your Yamaha SC System. Upgraded shaft & bearings directly
replace OEM parts for maximum durability in performance applications.
Manufactured exclusively for RIVA by HKS, these components feature
superior materials & finishing treatments for reduced friction and abrasion
resistance.
Key benefits include:
• Reduced friction between moving parts • Increased fatigue strength in parts
• Higher resistance to surface abrasion • Improved seize resistance
Kit includes supercharger shaft, 2 bearings, shaft nut and instructions.
R&D offers an answer to both repairing & upgrading the O.E.M. superchargers
vulnerable thrust bearing and main shaft bearing assemblies. Engines with
superchargers running higher boost pressures and higher rpm frequencies will
eventually need bearing servicing. Servicing the supercharger main bearings
periodically or upgrading to R&D’s new “Duplex Bearing System” will extend
the life of the superchargers thrust bearing significantly. R&D offers both standard replacement bearing kits, and the new “Duplex Bearing Kit” that will work
in any Yamaha supercharger. R&D also offers complete rebuild kits for stock
superchargers running C1 Monster Wheel Kits and all supercharger wheel kits
using the stock exducer size. R&D also offers rebuild kits for all C3, C5, C7
Monster Wheel Kits with larger exducers.
BODY
Part No.
612-92010
612-92011
RIVA YAMAHA
FX-SHO/FZ
HEAVY DUTY SHAFT
UPGRADE KIT
612-25020
R&D SHO/FZR
HIGH PERFORMANCE
SUPERCHARGER
REPLACEMENT THRUST
BEARING/SEAL KITS &
DUPLEX BEARING KIT
R&D has designed a custom tool kit that is
essential in the rebuilding process of the
Yamaha Supercharger. All tools are specific
in application and are cnc machined to
ensure a precision job.
Description
A. Supercharger Housing Holder Bracket Tool
B. Shaft/Gear Holding Tool
Part No.
R&D FX-SHO/FZR Billet Supercharger Shaft Kit
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
This is a drop in impeller so no modifications to
the housings are necessary. Weighing a mere
106 grams this is the lightest impeller on the
market reducing wear and tear on the
clutch/shaft assembly. Output is 15+ psi @7700
rpm and an amazing 18+psi @8500 rpm.
Next R&D increased the inadequate 6mm thread diameter on the OEM shaft
to utilize a well proven “Turbo spec” LARGER 5/16-24 left handed thread that
will not break under extreme conditions. The larger thread diameter will also
allow wheel torque specs to be increased safely.
EXHAUST
Engine-Tech Xtreme Supercharger Impeller (16+ lbs)
ENGINE/
GASKETS
Description
INATKE
SYSTEMS
Must be used with adjustable fuel regulator, high flow intercooler and ECU
(Motec or equiv, Motec map available upon request)
R&D's new High Performance
Billet Supercharger Shaft
eliminates the weak design features of the OEM and aftermarket HKS supercharger shafts. After analyzing the OEM HKS shaft design and sorting through
the various failures we had with it while testing our popular Monster S/C
Wheels, we developed a superior shaft design. The new R&D shaft is not a
copy of the fragile HKS design. Rather, it is a completely new design, superior
in material strength and improved in every way. The new R&D Shaft is precision CNC machined, heat treated, and precision ground from billet steel alloy.
Featuring a uni-structure design that incorporates the shaft and gear as one
billet piece, much like a transmission shaft. This eliminates the fracture point
on the OEM design where the gear shears off the end of the shaft. The billet
design will not allow the gear to slip under high boost loads like the pressed on
OEM gear.
YAMAHA
4 STROKE
Engine-Tech Xtreme series supercharger impeller
from Race Tech for Yamaha 1.8 liter supercharged
engines. This billet aluminum impeller was computer
designed for maximum efficiency and produced on a
5 axis CNC center. It then gets computer balanced
and anodized for corrosion resistance. Every gram of excess weight was
shaved from this impeller to make it the lightest impeller on the market without
sacrificing strength. It is a full 17% lighter than the stock impeller for better
clutch and shaft life. This impeller can produce up to an astonishing 16+ lbs of
boost !
R&D YAMAHA
SHO/FZR BILLET
SUPERCHARGER
SHAFT KIT
31
YAMAHA FX-SHO & FZ • SUPERCHARGER
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
R&D FX-SHO/FZR
SURGE PROTECTOR KIT
The R&D Yamaha FX-SHO/FZR Surge
Protector Kit will significantly improve
supercharger clutch and compressor
wheel performance and reliability by
eliminating damaging compressor surge.
The R&D Surge Protection Kit utilizes an
automotive vacuum assisted Bosch pressure blow off valve that releases the
unwanted intake pressure between the throttle valve and the supercharger
thus keeping the pressures in P1 and P2 equal. As soon as the throttle
valve is opened, the blow off valve immediately closes and the compressor
can supply its full boost potentials to the engine. The R&D surge hose is
manufactured from high performance, high-temperature silicone with an
integrated molded riser for the blow off valve to function without hindering
intake flow or velocity. The R&D kit installs easily in place of the OEM rubber
elbow joint with no modifications. The R&D Pressure Port installs between
the MAP sensor and the MAP sensor bracket with a “bolt on” part. The R&D
Surge Protection Kit is a necessary and cost effective upgrade for the
Yamaha SHO/FZR supercharged engine. The R&D kit comes completely
assembled with silicone elbow, blow off valve, R&D B.O.V. filter, mounting
hardware and instructions.
Description
Part No.
R&D Surge Protector Kit
612-18008
BODY
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
Riva Performance Blow-off Valve Kit improves supercharger reliability and
performance by relieving unwanted pressure during off-throttle operation.
Reduces supercharger clutch & gear wear and eliminates heat soak in
discharge tube. High-strength silicone hose with integrated HKS valve
installs easily in place of OEM elbow joint. Includes high quality HKS Super
SQV (Super Sequential Blow Off Valve) that features unique sequential valve
structure and a differential pressure control system, allowing for a broad
operation boost range. Also includes vacuum line and fittings necessary for
installation on SHO engine. A simple and cost effective upgrade for both stock
and modified engines.
Description
RIVA FX-SHO/FZ Performance Blow-off Valve Kit
R&D FX-SHO/FZR/FZS
SILICONE INTAKE HOSE KIT
The R&D Yamaha FX-SHO/FZR/FZS Supercharger
High Performance Hose Kit was developed while testing the R&D Monster
Compressor Wheel Kits. Higher boost pressures create higher intake air temperatures of up to 235 degrees. The O.E.M. standard black rubber hose and
standard hose clamps just do not hold up to the pressures and heat like high
quality, high temperature silicone hose and high strength stainless steel T-bolt
style hose clamps. The R&D “Blue Hose” is manufactured from high performance, turbo charger quality high-temperature silicone. The R&D silicone hose
installs easily in place of the OEM rubber elbow hose, and T-bolt clamps will
keep the hose secure for the longest of endurance races.
Description
Part No.
RY17040-BV
RIVA FX-SHO/FZR
BLOW-OFF VALVE KIT
High quality HKS Blow-off Valve reduces
wear and tear on clutch & drive gears of
supercharger and eliminates heat soak in
discharge tube. For use with RIVA FX-SHO/FZ
Power Cooler (part# RY17040-PC). HKS Super SQV (Super Sequential Blow
Off Valve) features unique sequential valve structure and a differential
pressure control system, allowing for a broad operation boost range.
Includes vacuum line and specific fittings necessary for installation.
Description
Riva FX-SHO/FZR Blow-Off Valve Kit
Part No.
RY17040BOVSSQV
Part No.
R&D FX-SHO/FZR/FZS Silicone Intake Hose Kit
R&D GREDDY BLOW
OFF VALVE & 1"
HOSE ADAPTER
R&D GReddy Blow Off Valves are
easily adjustable to eliminate
compressor surge and preventing
premature boost leakage, while
613-95262
613-95261
increasing boost response. Each
valve is made of durable cast and billet aluminum frame and the valve to
diaphragm ratio provides performance that cheap piston types cannot offer.
The spring stiffness adjustment screw and the three different sizes give the
GReddy user the option to match vehicles with mild upgrades to heavily
tuned engines. There are many factors in matching a blow-off valve to an
application, valve location, turbocharger/supercharger size and pressure, but
as a general rule of thumb, we recommend the Type RZ for 100-400hp.
Description
R&D Greddy Blow Off Valve & 1” Hose ADAPTER
R&D 1” O.D. Hose Adapter for Greddy Valve
R&D
SUPERCHARGER
CLUTCH REMOVAL
TOOL
612-18007
1" Hose ADAPTER sold separately.
32
RIVA FX-SHO/FZ PERFORMANCE
BLOW-OFF VALVE KIT
Part No.
613-95261
613-95262
This R&D tool enables the clutch to be changed in a
matter of only minutes. With the supercharger and
front engine cover removed the tool drops down
through the case and secures the drive gear at the
front of the crankshaft from rotating when the clutch is
removed and installed. This is a “must have” tool that will save massive
amounts of time for any mechanic.
Description
R&D Supercharger Clutch Removal Tool
Part No.
612-92012
R&D FRONT COVER GASKET
R&D’s new Front Cover Gasket features a metal
reinforced center that enables it to be reusable when
servicing the supercharger clutch.
Description
R&D Front Cover Gasket
Part No.
080-21024
YAMAHA FX-SHO & FZ • INTERCOOLER
YAMAHA
4 STROKE
INATKE
SYSTEMS
R&D FX-SHO/FZR STAGE 1
INTERCOOLER CORE KIT
Description
R&D FX-SHO/FZR/FZS Stage 1 Intercooler Core Kit
Part No.
612-18001
Description
RIVA FX-SHO/FZR Power Cooler Kit
Part No.
RY17040-PC
* Significantly improves cooling efficiency
* Flows 40 CFM more than stock
* Bolts directly into stock location w/oem hardware
* Increases overall horsepower
* Aggressive holeshot and mid range acceleration
* Works great with C1 or C3 Monster compressor wheels
* Retains O.E.M. flushing system for maintenance
* I.J.S.B.A. and A.P.B.A. Limited Class Legal (Rule 7.8.3.)
*7.8.3 AIR/FUEL DELIVERY — FOUR-STROKE (RUNABOUTS ONLY)
Turbocharger impeller or supercharger impeller may be modified or
aftermarket. The impeller housing must remain stock as supplied by the
manufacturer. Intercoolers may be modified or aftermarket. Intercooler
heat exchange surface area may not be increased by more than 25%.
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Note: Power Cooler requires use of one of the following components:
RIVA FX-SHO/FZ Power Cooler Blow-off Valve Kit (part# RY17040-BOVSSQV) or RIVA Blow-off Valve Block-off Kit (part# RY17040-BVBO-SSQV)
The R&D Yamaha SHO/FZ/FZR Pro Limited Intercooler Kit was developed to
directly replace the restrictive O.E.M. intercooler. The new R&D design offers
high performance affordable intercooling that will bolt into the OEM stock
location utilizing the OEM inlet cover, and all stock hoses and hardware.
The new R&D design is IJSBA & APBA Limited Class legal, complying with
rule book regulating aftermarket intercooler size. The R&D Intercooler has
been specifically designed, sized, and routed to also comply with the
I.J.S.B.A.’s 25% rule. The Intercooler Kit is constructed from aircraft
aluminum and is extremely easy to install, removes quick for cleaning and
winter storage, is ultra strong, and rubber mounted so vibration will not
compromise the long term performance. The R&D intercooler offers better
cooling efficiency through a aluminum core design that easily out performs
cheaper inefficient intercooler cores known to crack, leak and cause extreme
detonation. The R&D intercooler core will flow more air, deliver better cooling
efficiency, and allow C1 and C3 Monster Wheel to live up to their airflow volume and power potential. The new R&D design drastically reduces deadhead
air restriction producing ultra responsive “POWER NOW” acceleration all the
way through the RPM range.
The R&D Pro Limited Intercooler Kit has also incorporated an integral flange
which will allow the easy bolt on addition of a Greddy RZ Blow-off valve
which can be adjusted to regulate boost, and compressor surge blow-off
under deceleration.
BODY
RIVA FX-SHO/FZR POWER COOLER KIT
The RIVA Power Cooler intercooler system features a huge cooler element
that is rated for up to 450hp. Delivers an increase of 20 peak horsepower over
original intercooler. Quality manufacturing of cooler core ensures the highest
boost pressure capacities, minimal pressure drops and excellent thermal
efficiency. The cooling element is dramatically reduces exit temperatures
averaging 60°F cooler than stock. Innovative design allows easy disassembly
of cooler element & ducting for maintenance and cleaning. Features
integrated blow-off valve mount that will accept RIVA/HKS Blow-Off Valve
kit (sold separately) for improved supercharger reliability and performance.
Power cooler installs securely with shock absorbing rubber mounting system
and stainless steel hardware.
R&D YAMAHA SHO/FZR
PRO LIMITED INTERCOOLER KIT
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Flows 40 CFM more than stock • 3 pounds lighter than stock
Improves cooling efficiency
• Bolts directly into stock location
Increases horsepower by reducing restrictions
Works great with C1 compressor wheel
Retains O.E.M. flushing system for maintenance
EXHAUST
•
•
•
•
•
ENGINE/
GASKETS
The R&D Yamaha FX SHO/FZR Stage 1 Intercooler
Core Kit was developed to replace the over restrictive OEM intercooler with an inexpensive direct
replacement core that will bolt in to the OEM stock
location with all stock hardware. The R&D Intercooler Core reduces the
deadhead air restriction (similar to the R&D Intake Core Kit) that is created
when installing a C1 Monster compressor wheel with a 3-4 pound boost
pressure gain. The R&D Intercooler offers better cooling efficiency with an
aluminum 8 core design.
Description
Part No.
R&D Yamaha SHO/FZ/FZR Pro Limited Intercooler Kit 612-18004
33
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO & FZ • INTERCOOLER
34
R&D
FX-SHO/FZR/FZS
INTERCOOLER
COOLING KIT
The R&D Yamaha FXSHO/FZR/FZS Intercooler
Temperature Control system was developed to offer
an inexpensive complete
bolt on kit that will allow the
full performance and cooling potential the O.E.M. intercooler has to offer for
recreational applications. Intercooler core water temperatures have a range of
affect on the supercharged air temperatures that enter into the engine. The
Yamaha SHO Intercooler operates on a single low pressure (10 P.S.I.) line of
lake temperature water to cool the intercooler. R&D has found that by adding
an additional intercooler water in line, and adding an additional water out line
and bypass fitting, there will be double the water flow volume at 20 P.S.I.
Reduced intercooler core temperatures can add a noticeable increase in
low end and midrange power along with reduced detonation. R&D offers a
range of machined flow control fittings to allow water volume control tuning for
intercooler temperature adjustments for warm lake water and extreme hot air
conditions. R&D also offers a pressure relief blowoff valve kit for high water
volume flow rates on higher boost Stage 1 and up engine kits. The R&D Kit
will allow temperature tuning that will deliver surprising results. Unlock hidden
performance and power potential in the OEM stock intercooler or aftermarket
intercooler system by reducing intercooler core temperatures.
• More horsepower with cooler intake air temperatures
• Increased acceleration and mid range performance
• Reduces detonation in hot weather conditions
• Temperature control tuneability
• An inexpensive recreational performance addition
• Pressure relief valve options
• Easy installation instruction
Description
R&D FX-SHO/FZR/FZS Intercooler Cooling Kit
The R&D Yamaha
SHO/FZR
Engine/Intercooler
Cooling Kit was developed for high performance recreational and racing use. Extensive engine
cooling and inlet air temperature testing using both MoTeC I2 and Innovate
digital logging systems has proven the R&D High Performance Cooling Kit to
offer double the water volume flow through the engine, oil cooler, and intercooler as well as increase water pressure. The O.E.M. cooling system has a
very low water pressure (10 P.S.I. at 7600 rpm’s) and a low water volume
flow. The new R&D kit will double the water volume which will lower intake air
temperature by 15-20 degrees as well as lower engine block and head temperatures by 40-50 degrees. The additional oil cooler water line will lower
engine oil temperatures by 15-20 degrees promoting better lubrication and
increased engine cooling. The R&D Cooling Kit arrives 100 percent complete
with pre-cut hoses, “T” connectors, dual line pump block, through hull bulkhead fittings, hose clamps, water by-pass fittings, the thermostat removal
sealing washer, and detailed instructions with pictures. R&D recommends the
cooling system to be upgraded as a stand alone performance upgrade and a
must have kit addition when installing power adders such as R&D
Supercharger Wheels, Engine Performance Parts, and Engine Management
Kit parts. Cooler engine, inlet air, and oil temperatures produce higher horsepower with decrease detonation
*Better throttle response, increased horsepower
*Cooler header and under seat temperatures
*Increased power with cooler air inlet temperatures
*Cooler cylinder and cylinder head will reduce knock
*Cooler oil will lubricate better and last longer
*Increased engine protection
*Improved clutch performance with cooler oil
Description
R&D SHO/FZR Engine/Intercooler Cooling Kit
Part No.
660-18001
Part No.
660-18000
R&D FX-SHO/FZR/FZS
INTERCOOLER
TEMPERATURE
CONTROL PRESSURE
RELIEF VALVE KIT
R&D also offers a pressure relief
blowoff valve kit for high water
volume flow rates on higher boost
Stage 1 and up engine kits. The
R&D kit will allow temperature tuning
that will deliver surprising results. Unlock hidden performance and power
potential in the OEM stock intercooler or aftermarket intercooler system by
reducing intercooler core temperatures.
Description
R&D FX-SHO/FZR/FZS Intercooler
Temperature Control Pressure Relief Valve Kit
R&D YAMAHA
FX-SHO/FZR
ENGINE
INTERCOOLER
COOLING KIT
Part No.
660-82511
RIVA ENGINE BREATHER UPGRADE KIT
Easy to install Engine Breather Upgrade Kit
eliminates power-robbing crankcase emissions from your engine's air intake.
Increases horsepower by removing the engine's requirement to burn relatively
non-combustible oil. Also improves intercooler efficiency by preventing the oil
sludge coating that lowers
thermal efficiency. Easy installation retains highly efficient OEM air/oil separator
system. Kit includes pre-formed hose with attached K&N filter along with all
necessary hardware & instructions.
Description
RIVA Engine Breather Upgrade Kit
Part No.
RY19040-EBUK
YAMAHA FX-SHO & FZ • INTERCOOLER
Description
SHO/FZR/FZS/VXR/VXS
BODY
RY10040-ECUK-1
Part No.
660-18004
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Description
Part No.
RIVA FX-SHO/FZR Stock Intercooler Upgrade Kit RY17040-ICUK
EXHAUST
Key Benefits Include:
• Intercooler exit temps average 30-degrees cooler than stock.
• Increased horsepower with cooler, denser air temps.
• No drilling or machining required to OEM intercooler.
• Includes billet "high-flow" pump strainer providing a second dedicated
waterline to intercooler.
• Replaceable sacrificial zinc anode protects cooling system from corrosion.
• IJSBA/ABPBA Stock Class Legal.
ENGINE/
GASKETS
The RIVA Intercooler Upgrade Kit delivers a huge performance gain to your
stock intercooler system. The cost efficient upgrade kit features billet
aluminum spacers that increase the end tank capacity and water flow in and
out of the OEM intercooler.
INATKE
SYSTEMS
RIVA FX-SHO/FZR STOCK INTERCOOLER
UPGRADE KIT
The R&D Block Thermostat Kit
Option was developed to offer a
way to run “Dual Thermostats” to
the engines cooling system
to control and allow warm up and
pre heat cycles to take place.
Engine Block and Head cooling on the Yamaha Engine becomes difficult
when running high compression ratios, higher boost levels, and aggressively
advanced ignition timing. R&D has found that multiple cooling lines need to be
added to the cooling system to provide enough volume to keep temperatures
stable and in check. The problem is the Single OEM thermostat is too restrictive and doesn’t allow enough water volume flow to reduce temperatures with
the added cooling lines. R&D has found a way to add an additional thermostat
that allows enough water flow volume to cool the engine and head and retain
the O.E.M. method for engine pre heat or warm up. The R&D Kit installs as a
bolt on kit directly in place of the corrosion anode. Running two thermostats
allows enough water flow to cool the engine properly. The R&D thermostat kit
option will start to open at 120 degrees, and will allow full flow at 140
degrees. The O.E.M. stock thermostat opens at 118-126 degrees and allows
full flow at 140 degrees. Having two thermostats installed that are full open at
140 degrees, and flow enough water volume, will help to keep engine block
temperatures to between an ideal 150-175 degrees. R&D has done extensive
testing with the engineers at MoTeC both on the Dyno and on the water to
determine that 150-160 degrees block temperatures is where the most peak
power is, any hotter and power diminishes. The R&D dual thermostat kit will
be a must have addition where engines are being run in extreme cold water
and weather conditions. There has been many debates over these theories,
and until now there has been no way around extended warm up cycles to
bring engine temps up before high engine loads can be applied. R&D has
found a way to end the debate and give everyone what they are looking for in
a complete cooling system.
YAMAHA
4 STROKE
ENGINE BLOCK
THERMOSTAT KIT
COOLING OPTION
RY10040-ECUK-PC
The RIVA Engine Cooling Upgrade Kit delivers dramatically improved cooling
efficiency to engine and oil cooler for increased reliability & performance.
Greatly enhances water flow & pressure by replacing restrictive OEM water
fittings with high-flow billet fittings and superior routing. Allows the addition of
aftermarket ECU's, high-boost compressor wheels and other performance
modifications that can increase heat & detonation. Includes all necessary
water lines, hardware, fittings and detailed installation instructions.
Fits 2009-10 FX-SHO & FZ models.
Description
Part No.
FX-SHO/FZ Engine Cooling Upgrade Kit
RY10040-ECUK-1
For use with the OEM Intercooler Upgrade Kit
FX-SHO/FZ Engine Cooling Upgrade Kit
RY10040-ECUK-PC
For use with the Riva Power Cooler Kit
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
RIVA FX-SHO/FZ ENGINE COOLING
UPGRADE KITS
35
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO & FZ • INTAKE • EXHAUST
BILLET EXHAUST
OUTLET
The new R&D Billet Exhaust
Outlet.
RIVA REAR EXHAUST KIT
RIVA Racing Rear Exhaust Kit delivers performance and cutting-edge style.
Allows for removal of restrictive sound suppression system located between
waterbox and hull exit. Improves engine performance by reducing back
pressure and restriction. Includes mandrel bent aluminum exhaust tube that
is powder coated to prevent corrosion, large billet through-hull exhaust outlet,
billet OEM exhaust outlet block-off and high-temp silicone couplers along
with all necessary mounting hardware & installation.
Description
RIVA Racing FZR/FZS Rear Exhaust Kit
RIVA Racing FX-SHO Rear Exhaust Kit
RIVA Racing VXR/VXS Rear Exhaust Kit
Replaces the restrictive sound suppression system located between the water
box and hull exit on your watercraft.
Improves engine performance by reducing back pressure and harmful detonation. Includes mandrel bent aluminum tubing that is powder coated to prevent corrosion, high-temp silicone replacement
coupler and installation instructions.
R&D HIGH TEMPERATURE
SILICON COUPLINGS
Description
3" - 3" High Temp Silicon Couplings
3" - 2" Reducer High Temp Silicon Couplings
2.75" - 2.5" Reducer High Temp Silicon Couplings
3" - 2.75" Reducer High Temp Silicon Couplings
Part No.
061-30030
061-32500
061-32501
061-32750
Part No.
RY16040
R&D FX-SHO/FZR/FZS HIGH
FLOW EXHAUST KIT
The R&D SHO High Flow Exhaust Kit will add a
noticeable low end and mid range power feel as
well as add top end performance! The R&D High
Flow Exhaust Kit will add a great performance
sound to the SHO while maintaining a safe and under IJSBA and Coast
Guard approved 86 db!
Description
FX-SHO/FZR/FZS High Flow Exhaust Kit
RIVA VXR/VXS Free Flow Exhaust Kit
Part No.
332-18000
RY16060
EXHAUST RESONATOR
REMOVAL KIT
The R&D Exhaust Resonator Removal Kit will allow the
sound suppression ball to be removed and plugged.
When removing the exhaust sound suppression ball and
modifying the exhaust hose, low end response is gained
and trapped hot exhaust gases can be evacuated quicker through less restriction or back pressure.
Description
VXR/VXS Exhaust Resonator Removal Kit
36
Part No.
331-30000
331-32750
Part No.
RY15050
RY15040
RY15060
RIVA FX SHO/FZR FREE
FLOW EXHAUST KIT
Description
Riva FX-SHO/FZR/FZS Free Flow Exhaust Kit
Description
3" Diameter R&D Billet Exhaust Outlet
2.75" Diameter R&D Billet Exhaust Outlet
Part No.
332-18005
RIVA FX-SHO/FZ PRO-SERIES WATER BOX
Developed on our Dyno and tested extensively on the water, this water box
features radiused exhaust tubes and end caps for optimum exhaust flow.
Unique exhaust baffle will increase the low-end power and mid-range pull of
your Yamaha watercraft. Delivers up to 15hp on modified engines along with
significant torque gains. High-strength aluminum construction will survive
backfires and meltdowns. Powder coated to prevent corrosion.
A must for modified motors.
Key Features:
• Delivers up to 15hp on modified craft!
• Machined hose flanges for reliable coupler retention.
• Radiused exhaust tubes & end caps.
• Powder coated to prevent corrosion.
Description
Riva FX-SHO/FZ Pro Series Water Box
Part No.
RY16041
YAMAHA FX-SHO/FZ/VXR/VXS • FUEL SYSTEM
Description
R&D FX-SHO/FZR/FZS/VXR/VXS In-Tank Fuel
Pressure Regulator Block Off Kit
Part No.
812-35257
R&D INLINE
FUEL
PRESSURE
GAUGE
ADAPTER
The R&D Fuel
Pressure Gauge
ADAPTER Tool is
designed to be a plug
in fuel pressure gauge that needs no modifications to install and use. Simply
disconnect the OEM locking fuel connector from the fuel rail and plug the
gauge tool directly into the connector. Plug the locking connector supplied on
the R&D tool onto the fuel rail and lock. Use the tool to verify fuel pressure
and fuel pump condition. Use the tool to set and verify base fuel pressure
settings on the R&D Rising Rate Fuel Pressure Regulator (RRFPR). When
finished, disconnect the tool and reconnect the stock fuel line. The ADAPTER
installs inline between the OEM fuel rail and the R&D RRFPR via the OEM
connectors for easy connect and disconnect. The R&D Tool works on both
Yamaha and Kawasaki fuel systems. Installation time is only 2 minutes.
Liquid filled fuel pressure gauge sold separately.
Description
R&D Inline Fuel Pressure Gauge ADAPTER
Liquid Filled Fuel Pressure Gauge
Part No.
612-00081
900-02180
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
R&D offers a Fuel Pressure Regulator Block
off Kit which will allow the OEM stock in tank
fuel pressure regulator to be removed, blocked off, and replaced with a billet
part which is mandatory when installing an aftermarket externally adjustable
fuel pressure regulator system. The OEM in tank fuel pressure regulator
is fixed to maintain 40-43 pounds of fuel pressure at all times. For high
performance applications where horsepower is boosted, it is necessary to
install larger flowing fuel injectors and be able to tune the fuel pressure up or
down as needed. Most factory race teams are running 65 plus pounds of fuel
pressure along with higher flowing fuel injectors and externally adjustable
pressure regulators. The R&D has a complete line up of fuel pumps, fuel
injectors, fuel pressure regulators, fuel gauge, and fuel hose accessories all
designed specifically for the Yamaha SHO. All R&D fuel injection parts and
products meet Coast Guard, I.J.S.B.A., and APBA approval.
Part No.
RY12040-RRFPR-6S5
BODY
R&D-FX SHO/FZR/VXR/VXS
IN-TANK FUEL PRESSURE
REGULATOR BLOCK
OFF KIT
Description
Riva Fuel Pressure Regulator Kit
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Part No.
802-00080
Fits Yamaha FX-SHO, FZR & FZS models.
EXHAUST
Description
R&D FX-SHO/FZR/FZS/VXR/VXS
Fuel Pressure Regulator Kit
Key Features Include:
• Precision fuel pressure control with optional rising rate function.
• High quality stainless steel liquid-filled pressure gage.
• Large 3/8 fuel return line.
• Includes billet Fuel Pressure Regulator Block-Off.
• Easy bolt-on installation with OEM fuel connectors.
• Includes complete installation instructions & tuning guide.
ENGINE/
GASKETS
R&D offers a Yamaha FX-SHO/FZR/FZS model specific fuel pressure regulator system allowing custom fuel pressure tuning to the EFI fuel systems fuel
pressures. The R&D Fuel Pressure Regulator System offers a wide range of
setup possibilities. Base fuel pressure is adjustable from 5 to 60 PSI. The R&D
fuel pressure regulator can also be set up to allow “rising rate” fuel pressure at
a 1 to 1 ratio (One pound of fuel pressure gain over base for every pound of
boost gain). R&D offers two types of fuel pressure regulator set ups. Part
#802-00080 will come completely assembled and ready to install. The R&D
Pro System is 100 percent complete, installs directly to the top of the fuel
tank, and connects directly to the fuel rail with OEM security lock connectors
with no modifications. For the R&D Fuel Pressure Regulator only use part
#801-25010, which comes complete with 90 degree barbed brass fittings for
use with push on type hose and Oetiker style clamps for security. R&D offers
high performance fuel hose that can be purchased by the foot, as well as the
Oetiker style clamps. The R&D bypass style regulator system is capable of
handling any fuel pump up to 250 GPH. Replace “Deadhead” regulator
performance and experience the full flow volume and rock steady fuel
pressure that only a dynamic R&D fuel pressure regulator kit can produce.
•
Fuel pressure will rise on a 1:1 ratio when boost referenced
•
All ports are 3/8” NPT, with one inlet, 3 outlets, and one return
port on the bottom
•
Beautiful type II bright dip anodized finish
•
Bypass design produces the ultimate, dynamic fuel delivery system
•
3/8 pipe tapped for standard or AN fitting ready
•
R&D offers pre-assembled #4 AN hose to finish off a return system
•
R&D offers fuel hose by the foot for custom routing
INATKE
SYSTEMS
R&D FX-SHO/FZR/FZS/VXR/VXS
FUEL PRESSURE REGULATOR KIT
Riva Fuel Pressure
Regulator Kit provides
the precision pressure
control necessary to
compliment aftermarket
ECU applications on the
'SHO' engine. Kit is fully
assembled & mounts
securely on top of fuel tank
via sturdy aluminum
bracket. High quality billet
pressure regulator can
adjust base pressure from
25 to 80 PSI. Unit can also
be set up as rising rate fuel pressure regulator at a 1 to 1 ratio providing one
additional pound of fuel pressure for every pound of boost gain. Plugs directly
into original fuel system with OEM connectors and features a large 3/8" fuel
return line that is routed through supplied rubber fuel tank cap. Includes
integrated liquid-filled pressure gauge and billet Fuel Pressure Regulator
Block-Off necessary for removal of stock fuel pressure regulator in fuel tank.
YAMAHA
4 STROKE
RIVA FX-SHO/FZ
RISING RATE
FUEL PRESSURE
REGULATOR KIT
37
RIVA/HKS FX-SHO/FZ
HIGH VOLUME FUEL PUMP
This is a direct replacement high volume fuel pump for high performance
applications. Delivers 265LPH to support highly modified engine packages.
Easy installation requires no modifications. Includes detailed installation
instructions.
Upgrade Kit
Complete Kit
R&D TUNABLE RAISING RATE FUEL
PRESSURE REGULATOR
The R&D Tunable Raising Rate Fuel Pressure Regulator enables the “raising
rate” portion of the fuel pressure to be tuned. With the addition of two volume
plates and three jets that change the internal volume and pressure the “raising
rate fuel pressure curve” can be manipulated. The regulator comes with a
baseline setup, which contains no volume plates or jets. The baseline setup
will provide a larger increase in fuel pressure as boost increases. If a lower
slope (leaner) is desired, the volume plates and jets can be installed to tune
the raising rate fuel pressure. The regulator utilizes a tunable pressure relief
port to lower the slope of the curve to dampen pressure transitions. Kit comes
complete with a graph page indicating the increase in fuel pressure as boost
increases with and without the volume plates and jets installed.
NOTE: Tuning the rising rate is necessary to be able to tune out rich spots in
the fuel curve caused by varying intercooler performance.
Description
Part No.
Tunable Raising rate Upgrade Kit (for R&D RRFRP) 802-00081
Tunable Raising Rate Fuel Pressure Regulator Kit 802-00082
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
Part No.
RY12040-265FP-6S5
R&D FX-SHO/FZR/FZS/VXR/VXS
HIGH PERFORMANCE
HIGH VOLUME FUEL PUMP KITS
R&D Performance carries a complete line up of high performance
replacement fuel pumps that are machined specifically to fit the Yamaha
FX-SHO/FZR/FZS fuel pump housing and are offered in a variety of flow
ratings to facilitate from basic low cost replacement to an all out 500 H.P.
race machine. All R&D FX-SHO/FZR/FZS fuel pumps have been precision
flow rate tested and charted in (LPH) liters per hour. R&D FX-SHO/FZR/FZS
fuel pumps arrive complete with Yamaha FX-SHO/FZR/FZS model specific
installation instructions complete with detailed photos that will help make the
fuel pump installation quick and easy.
Description
R&D FX-SHO/FZR/FZS/VXR/VXS 190 LPH
OEM Replacement Fuel Pump Kit
R&D FX-SHO/FZR/FZS/VXR/VXS 255 LPH
Low Pressure Fuel Pump Kit
R&D FX-SHO/FZR/FZS/VXR/VXS 255 LPH
High Pressure Fuel Pump Kit
Part No.
812-35190
812-35255
812-35256
R&D FX-SHO/FZR/FZS
MULTI-PRESSURE PORT BOOST
GAUGE/SURGE/RRFPS ADAPTER KIT
The R&D Yamaha FX-SHO/FZR/FZS Multi-Pressure Port ADAPTER Kit will
allow quick and easy hook up of digital or manual boost gauges with the
R&D Multi-port billet ADAPTER. The R&D Pressure Port ADAPTER installs
between the MAP sensor and the MAP sensor bracket as a “bolt on” part
no with modifications. Operate a vacuum/boost gauge, check plenum air
temperatures, and operate a surge protection valve at the same time, or run
a boost gauge, surge protection device, and operate a boost referenced fuel
pressure regulator (RRFPR) at the same time with one simple part. The R&D
Pressure Port ADAPTER Kit comes complete with longer MAP sensor mounting screws, o-ring seals, nylon cable ties, all mounting hardware and instruction.
Description
R&D FX-SHO/FZR/FZS Multi-Pressure Port Boost
Gauge/Surge/RRFPS ADAPTER Kit
38
Description
RIVA/HKS FX-SHO High Volume
Fuel Pump
NOTE: There are no modifications necessary to install the R&D fuel pump
therefore switching back to the O.E.M. fuel pump assembly is quick and easy
as well.
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • FUEL SYSTEM
Part No.
612-92005
R&D #4 & #6 FUEL RETURN LINE KIT
R&D has developed a two larger fuel return line kits for the
FX-SHO/FZR/FZS. Increasing the diameter of the fuel return line to #4
or #6, decreases line pressure and increases fuel volume, yielding increased
tuning ability in high heat and higher performance applications.
Description
R&D #4 Fuel Return Line
R&D #6 Fuel Return Line
Part No.
612-00082
612-00083
YAMAHA FX-SHO/FZ/VXR/VXS • FUEL SYSTEM
Riva’s high performance fuel injector kit supplies modified Yamaha 1.8 liter
Supercharged engines with additional fuel for RIVA Stage II & III applications.
These 95lb injectors are designed for use with RIVA Pro-Series ECU for correct calibration. Injector sets are flow-matched for optimum idle quality and
peak performance.
Description
Riva FX-SHO/FZR/FZS
Pro-Series Fuel Injector Kit
Part No.
RY12040-I-KIT
RIVA FX SHO/FZ
3 BAR MAP
SENSOR KIT
Do you plan on running over
14.7psi of boost? If so, our
3 Bar MAP Sensor Kit is
essential for accurate engine
management with high
boost applications. High
quality 3 Bar MAP Sensor
will measure up to 29.7psi, where the OEM 2 Bar MAP Sensor will only measure up to 14.7psi. It is critical to provide accurate pressure information to your
aftermarket ECU to ensure proper air/fuel mixture and data logging. RIVA 3
Bar MAP Sensor mounts directly in place of OEM sensor with stainless bracket and plugs directly into OEM wiring harness.
Description
Riva FX-SHO/FZ 3 Bar Map Sensor Kit
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Part No.
812-18000
RIVA FX SHO/FZR
PRO-SERIES FUEL INJECTOR KIT
BODY
Description
R&D FX-SHO/FZR/FZS/VXR/VXS High Perf.
Fuel Injector Kit
Part No.
RY12040-I-KIT-100
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
When boosting the horsepower on the
FX-SHO/FZR/FZS four stroke fuel injected engine, whether using high compression pistons, cams, or higher ratio supercharger compressor wheels, it
will be necessary to increase the fuel flow delivery. The OEM Yamaha SHO
injectors have been precision flow rate tested to be 80 percent peaked on
stock units at sea level without modifications. R&D offers high performance fuel
injectors with a higher atomization spray pattern that are easily capable of
delivering fuel flow specifications to accommodate up to 400 horsepower!
R&D has flow rate tested the O.E.M. Yamaha SHO injectors and verified them
to flow 396 cc at 43 PSI of fuel pressure, which rates them to flow 30 pounds
of fuel per hour. The R&D High Performance Fuel Injectors have precision
flow rate tested to 525 cc at 43 PSI of fuel pressure, and 625 cc at 70 PSI of
fuel pressure, which rates them to flow as much as 62 pounds of fuel per
hour. R&D High Performance Injectors have been flow rate tested to perform
excellent, delivering precise fuel at fuel pressure ratings ranging from 40 to 80
PSI. Each R&D High Performance Fuel Injector Kit will come packaged with
vital flow test rating information that will be broken down specifically in five
pound increments in fuel pressure to give the fuel flow delivery information
that will help in tuning fuel pressure to match the engines fuel flow needs
based on horsepower gains over stock. R&D offers only the highest quality
fuel injectors, fuel pressure regulators, and fuel management accessories,
for all your engine management needs.
Description
Riva Pro-Series Yamaha Fuel Injectors
EXHAUST
FX-SHO/FZR/FZS/VXR/VXS
HIGH PERFORMANCE
FUEL INJECTOR KIT
RIVA PRO-SERIES YAMAHA FUEL INJECTORS
Our high impedance fuel injector kit delivers additional fuel to modified
engines for high boost applications. 100lb (1,000cc) injectors are for use with
aftermarket ECU (RY11840-01-C) for correct calibration. Kit includes injectors,
plug and play adapters, fuel rail spacers and detailed installation instructions.
Fits 2009-11 FX-SHO & FZ models.
ENGINE/
GASKETS
Description
Part No.
R&D Pro-Series 725cc Injectors (set of 4)
812-18001
Flow Rate: 725cc at 43.5 Pounds of Pressure =72 Pounds Per
Fuel Hour Fuel Flow.
Flow Rate: 925cc at 70.0 Pounds of Pressure =92 Pounds Per
Fuel Hour Fuel Flow.
R&D Pro-Series 1000cc Injectors (set of 4)
812-18002
Flow Rate: 1000cc at 43.5 Pounds of Pressure =100 Pounds
Per Fuel Hour Fuel Flow.
Flow Rate: 1225cc at 70.0 Pounds of Pressure =120 Pounds
Per Fuel Hour Fuel Flow.
INATKE
SYSTEMS
R&D Pro Series injectors offer increased fuel
delivery over our 525cc injectors. The new Pro
Series injectors are offered in 725cc and
1000cc flow rates. Each set of injectors have been flow rate and voltage
comp tested to insure linear accuracy and are shipped with a precision dead
time (voltage compensation) chart that can be added into your aftermarket
ECU’s software program under battery compensations. R&D Pro Series
injectors offer perfectly clean linear response performance from low idle all
the way through the entire power range. R&D has flow rate tested the O.E.M.
Yamaha FX HO injectors and verified them to flow 396 cc at 43 PSI of fuel
pressure, which rates them to flow 39 pounds of fuel per hour. The R&D Pro
Series Fuel Injectors have been precision flow rate tested to 725cc at 43 PSI
of fuel pressure, and 925cc at 70 PSI of fuel pressure, which rates them to
flow as much as 92 pounds of fuel per hour. R&D fuel Injectors perform
excellent, delivering precise fuel flow at fuel pressure ratings ranging from 40
to 80 PSI. Each R&D injector set is packaged complete with all installation
hardware, necessary harness interface connectors, voltage compensation
chart, and instructions.
YAMAHA
4 STROKE
FX-SHO/FZ/VXR/VXS 725
CC/1000 CC PRO SERIES
FUEL INJECTOR KIT
Part No.
RY11740-MS-3
39
YAMAHA FX-SHO & FZ • ENGINE
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
FX-SHO/FZR HIGH PERFORMANCE R&D ECU REPROGRAMMING SERVICES
DOLLAR FOR DOLLAR UNBEATABLE PERFORMANCE: R&D is proud to announce our new line up of Yamaha FZR and SHO ECU reprogramming services.
The engineering staff at R&D have been testing and developing ECU programs to allow new performance levels to be reached for recreational enthusiasts and
racers who are interested in more performance through reprogrammed the OEM ECU. Entry level programs will allow the enjoyment of a raised RPM limit settings,
advanced ignition timing, re-calibrated fuel map, as well as the internal boost limiter raised to allow R&D Monster Wheels to work to full potentials. There are
several performance levels to choose from that work with stock or R&D C1, C3, and C5 Monster Wheels or any wheel kit rated up to 18 pounds of boost. Programs
offered are recreational performance tuned with safe AFR values, and can be further custom tuned (Richened) to accommodate additional boost levels. Existing
customers who have purchased an R&D Powershot Fuel Control Unit can send their units in to R&D for free upgraded re-programming to allow custom fuel tuning
to work with the new ECU Programs. R&D Powershot Fuel Control Units are not required on entry recreational level (R1, R2, or R3) programs using stock, C1, or
C3 Wheels. However, custom fuel tuning with the Powershot Fuel Tuner can be an add-on or additional upgrade that is suggested for higher performance applications such as C5 Monster Wheel Kits. Fuel tuning or AFR conditions should always be checked and verified as values will always be slightly different from one
engine set up to another. Higher performing programs are continuously under development and will be announced through updates on the R&D website, so stay
tuned. Custom program files can also be performed to accommodate just about any combination of performance level or type of fuel being used. R&D strongly suggests that AFR tuning be periodically verified using Innovate Products LM1 or LC1 Logging Kit also available from R&D.
Par t #802-01801 R&D R1 ECU; Reprogrammed ECU to allow up to 8450 RPM’s, Raised Boost limiter to allow up to 18 pounds boost, and upgraded ignition timing
safe for all recreational and offshore racing use. R1 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to 18 pounds of boost. 89
octane safe with stock and C1 wheels, 91 octane pump fuel use is recommended for C3 and C5. The R1 program file does not require a Powershot Fuel Tuner for
use with C1 and C3 Monster Wheels.
Par t #802-01802 R&D R2 ECU; Reprogrammed ECU to allow 8750 RPM’s, Raised Boost limiter to 17 pounds, advanced ignition timing for high performance
recreational use. R2 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to 18 pounds of boost. 91 octane pump fuel should be
used with R2 reprogram. 93-95 octane fuel is recommended for closed course racing conditions where high engine loads are present. The R2 program file does
not require a Powershot Fuel Tuner for use with C1 and C3 Monster Wheels.
Par t #802-01803 R&D R3 ECU; Reprogrammed ECU to allow 8850 RPM’s, eliminated Boost limiter, aggressively advanced ignition timing in the low end areas
and softer high rpm settings in the peak boost areas for high performance recreational use. R3 works great with C1, C3, or C5 Monster Wheel Kits, or any wheel
kit rated up to 18 pounds of boost. 91-93 octane pump fuel should be used with R3 reprogram with O.E.M. 8.6-1 pistons and cams. R&D suggests 100 plus octane
fuel when using 9.5-1 pistons, RC1 Cams, and R&D Pro Tune Adjustable Cam Gear Kits. NOTE: The R3 program file does not require a Powershot Fuel Tuner for
use with C1 and C3 Monster Wheels. Use the Powershot for custom fuel tuning with C5 wheel kits. NOTE: The R&D RRFPR Kit is required when using the R&D
C5 Monster Wheel Kit.
Par t #802-01803v R&D R3 VF ECU; Reprogrammed ECU allows the use of variable fuels. Run 91 octane at 12-13 pounds (180 kpa) of peak boost, and run 98
or 100LL Aviation fuel when boost pressure is adjusted to 15-18 pounds. The program allows 8850 RPM’s, eliminated Boost limiter, aggressively advanced ignition
timing in the low end areas and softer high rpm settings in the peak boost areas for high performance recreational use. R3 VF works great with C1, C3, or C5
Monster Wheel Kits, or any wheel kit rated up to 18 pounds of boost. 91-93 octane pump fuel should be used with R3 VF reprogram with O.E.M. 8.6-1 pistons and
cams at 12-13 pounds. R&D suggests 100 plus octane fuel when using 9.5-1 pistons, RC1 Cams, and R&D Pro Tune Adjustable Cam Gear Kits. NOTE: The R3 VF
program file does not require a Powershot Fuel Tuner for use with C1 and C3 Monster Wheels. Use the Powershot for custom fuel tuning with C5 wheel kits. NOTE:
The R&D RRFPR Kit is required when using the R&D C5 Monster Wheel Kit. NOTE: Adjusting the peak boost pressure is done via the R&D/GReddy adjustable
boost level/surge protection valve. The R3 VF Program allows the recreational rider/racer the flexibility to race on Sunday with 15-18 pounds of boost and
aggressive timing with 100 octane Aviation fuel, and still be able to take the family out for weekend fun with 91 octane pump gas when boost is adjusted back to
10-13 pounds. NO need for switching booster wheels to attain lower boost and lower rpm settings. Another great feature available only from R&D!
Par t #802-01804 R&D R4 ECU; Reprogrammed ECU to allow 8850 RPM’s, eliminated Boost limiter, aggressively advanced ignition timing that requires 100 octane
Aviation fuel for high performance Pro Stock or Pro Limited racing use. R4 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to
18 pounds of boost.
Par t #802-01805 R&D R5 ECU; Reprogrammed ECU to allow 8950 RPM’s, eliminated Boost limiter, aggressively advanced ignition timing that requires VP MS 109
race gas for high performance Pro Stock or Pro Limited racing use. R5 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to 18
pounds of boost.
Par t #802-01806 R&D R6 ECU; Reprogrammed ECU to allow 9000 RPM’s, eliminated Boost limiter, aggressively advanced ignition timing that requires VP MS
109E fuel for high performance Pro Stock or Pro Limited racing use. R6 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to 18
pounds of boost.
Par t #802-01807 R&D R7 ECU; Reprogrammed ECU to allow 9000 RPM’s, eliminated Boost limiter, aggressively advanced ignition timing that requires VP C12
race gas for high performance Pro Stock or Pro Limited racing use. R7 works great with stock, C1, C3, or C5 Monster Wheel Kits, or any wheel kit rated up to 18
pounds of boost.
Par t #802-01808 R&D R8 ECU; Reprogrammed ECU for 725cc injectors @ 52 psi fuel pressure, 8750 RPM’s, eliminated Boost limiter, advanced ignition timing
requires 91 octane pump gas for high performance recreational use. R8 is designed for the C5 Monster Wheel Kit or any wheel kit rated for 18 pounds of boost.
Par t #802-01809 R&D R9 ECU; Reprogrammed ECU for 725cc injectors @ 52 psi fuel pressure, 8850 RPM’s, eliminated Boost limiter, advanced ignition timing
requires 100 octane Aviation fuel. R9 is designed for the C5 Monster Wheel Kit or any wheel kit rated for 18 pounds of boost.
Par t #802-01810 R&D R10 ECU; Reprogrammed ECU for 725cc injectors @ 52 psi fuel pressure, 9000 RPM’s, eliminated Boost limiter, advanced ignition timing
requires VP MS 109 Race gas. R10 is designed for the C5 Monster Wheel Kit or any wheel kit rated for 18 pounds of boost.
Par t #802-01811 R&D R11 ECU; Reprogrammed ECU for 725cc injectors @ 60 psi fuel pressure, 9000 RPM’s, eliminated Boost limiter, advanced ignition timing
requires VP C12 Race gas. R11 is designed for the C5 Monster Wheel Kit or any wheel kit rated for 18 pounds of boost.
Par t #802-01812 R&D R12 ECU; Reprogrammed ECU for 1000cc injectors @ 60 psi fuel pressure, 9000 RPM’s, eliminated Boost limiter, advanced ignition timing
requires VP MS 109/C12 Race gas. R12 is designed for the C5 Monster Wheel Kit or any wheel kit rated for 18 pounds of boost.
NOTE: Rev Limiter settings can be raised or lowered upon request.
40
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE • FUEL SYSTEM
SHO/FZ/FZR Powershot Adjustable Fuel Tuner
Part No.
802-18000
Description
VXR/VXS Powershot Adjustable Fuel Tuner
Part No.
802-18010
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Description
EXHAUST
No more Boost Limiter!
ENGINE/
GASKETS
The R&D Powershot is fully adjustable to accommodate and properly
performance tune the A.F.R. for any combination of aftermarket parts.
• Preprogrammed and Pre set to 12.5:1 (plug in and run)
• Allows overall fuel map tuning
• Utilizes O.E.M. ignition system
• Utilizes O.E.M. fuel injectors
• Retains all O.E.M. dash, warning, and service indicators
• 91 octane pump gas friendly
• Ultra easy 20 minute installation
F o r c o m p e t i t i o n u s e o n ly !
INATKE
SYSTEMS
The new R&D Powershot Fuel Injection/Engine
Tuning module for the YAMAHA SHO/FZR will
deliver increased acceleration, stronger mid-range,
and increased top speed performance by delivering
a higher performing air to fuel ratio (A.F.R.) and allowing higher mass
air/boost pressure levels to be utilized. R&D Performance has data logged
and analyzed the O.E.M. fuel map and FlyBy Wire functions on the new
YAMAHA SHO/ FZR four stroke engine and has determined that one of the
main horsepower and performance holdbacks in Yamaha’s Fly by Wire E.C.U.
system is the mass air or boost limitation that is controlled by the Fly by Wire
Throttle System. The Yamaha E.C.U. manipulates and controls the mass air
or boost pressure levels by closing the throttle plate which limits peak horsepower performance. The R&D Powershot interfaces with the E.C.U., fuel
injectors, and sensors to unlock, take over, and control mass air or boost limitations. The R&D Powershot will allow the R&D C1 and C3 Monster
Supercharger Wheels to perform to their full potential by defending against
unwanted codes and internal E.C.U. limitations. The R&D Powershot comes
pre-programmed and coded to safely alter the fuel map, intercept and recondition sensor voltage signals allowing up to 10 P.S.I. of boost pressure without throttle limitation or regulation. The R&D Powershot allows custom fuel
tuning to cruise, acceleration, and top end zones. Top end fuel mixtures can
be custom tuned from 13.5:1 (lean) to 11.5:1 (rich) on the fly. Quicker
acceleration, stronger mid-range, and increased top speed performance is
the result when the A.F.R. is tuned for optimum performance.
R&D Powershot Fuel Injection/Engine Tuning module
for the YAMAHA VXR/VXS. The R&D Powershot will
deliver increased acceleration, stronger mid-range,
and increased top speed performance by delivering a
higher performing air to fuel ratio (A.F.R.) R&D
Performance has data logged and analyzed the
O.E.M. fuel map on the Yamaha 1.8 N. A. four stroke
engine and documented that the fuel tables are a very green and stoichiometric. If quicker acceleration and stronger mid range power and the ability to
have your cake and eat it too, then the Powershot is for you. The Powershot
will allow you to adjust the fuel to either run green or mean. The R&D
Powershot interfaces with the stock E.C.U., and fuel injectors allowing piggy
back adjustments to the fuel table. The R&D Powershot comes pre-programmed and coded to safely alter the fuel map right out of the box for plug
and play performance. The R&D Powershot allows custom fuel tuning to
cruise, acceleration, and top end zones. Top end fuel mixtures can be custom
tuned from 13.5:1 (lean) to 11.5:1 (rich) on the fly. Quicker acceleration,
stronger mid-range, and increased top speed performance is the result when
the A.F.R. is tuned for optimum performance. The R&D Powershot is fully
adjustable to accommodate and properly performance tune the A.F.R. for
any combination of aftermarket parts. Unlock the YAMAHA VXR/VXS’s full
performance potential with an R&D Powershot Engine Tuner. Call R&D today
and get the latest high performance tuning parts, accessories, and information!
YAMAHA
4 STROKE
R&D YAMAHA VXR/VXS
POWERSHOT
ADJUSTABLE FUEL TUNER
R&D YAMAHA
SHO/FZ/FZR
POWERSHOT
ADJUSTABLE
FUEL TUNER
BODY
Part #802-02801 R&D R1 ECU; Reprogrammed ECU for the VXR/VXS offers
improved ignition timing map advancements that produce quicker acceleration and top speed performance. The fuel maps are tuned to offer a cleaner
than stock (leaner idle), clean and green cruise areas which will keep fuel
consumption either the same or better than stock in the cruising ranges, and
an overall improvement to top speed or wide open throttle ranges. The rev
limiter is raised to allow up to 8150 RPM’s that will promote a more positive
pump hook up in rough water conditions. The R1 ECU programs are 89 and
91octane (pump fuel) safe. The R1 program file does not require a
Powershot Fuel Tuner.
Description
Reprogrammed ECU for the VXR/VXS
Reprogrammed ECU for the VXR/VXS
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
VXR/VXS HIGH PERFORMANCE ECU
REPROGRAMMING SERVICES
Part #802-02802 R&D R2 ECU; Reprogrammed ECU for the VXR/VXS
offers improved ignition timing map advancements that produce quicker
acceleration and top speed performance. The fuel maps are tuned to offer
a cleaner than stock (leaner idle), clean and green cruise areas which will
keep fuel consumption either the same or better than stock in the cruising
ranges, improved hard acceleration enrichment for the hard core rider that
want a more aggressive mid range acceleration, and an overall
improvement to top speed or wide open throttle ranges. The rev limiter is
raised to allow up to 8250 RPM’s that will promote a more positive pump
hook up in rough water conditions. The R2 ECU programs are 91octane
(pump fuel) safe. The R2 ECU program can be used with R&D Performer,
Stage 1 and 2 kits. The R2 program file does not require a Powershot
Fuel Tuner.
NOTE: Custom Rev Limiter settings available upon request.
Part No.
802-02801
802-02802
41
YAMAHA FX-SHO/FZ/VXR/VXS • FUEL
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
RIVA/VIPEC
PRO- SERIES ECU
42
The Pro-Series ECU provides a huge
performance advantage to the Yamaha
1.8L Supercharged Engine delivering
over 50hp to the stock engine. ECU is
fully programmable with either RIVA
supplied mapping or user defined
parameters. Most calibrations require
use of RIVA Fuel Pressure Regulator
Kit and 91+ octane pump fuel. Plugs directly into factory wiring harness via
waterproof connectors.
Key benefits include:
1) Easy loading of supplied calibrations/maps for various performance
applications.
* Performance Fuel Mapping: Delivers optimal fuel required for your specific
level of modification based on boost pressure.
* Performance Timing Curves: Special racing curves produce more power
throughout the RPM range.
* Rev Limiter Increase: Stock rev limit can been increased so engine RPM can
be run higher producing more boost pressure and horsepower.
2) Retains OEM Dash Display, Engine Diagnostic & Engine Safety Functions:
* All original dash functions are retained.
* Provides diagnostic information that can be displayed via computer interface.
3) Includes input for optional lambda sensor kit (part# RY11540-LC1-6S5) for
data logging air/fuel ratios & tuning functions.
4) Individual Cylinder Knock Control function. Identifies which cylinder is
detonating by tracking firing order utilizing OEM knock sensor.
5) Traction Control function. Can be calibrated to match specific applications.
6) Antilag function (for turbo applications).
RIVA LC1 WIDEBAND LAMBDA CONTROLLER
The LC-1 is a complete wideband Lambda controller built into a sealed cable
and wired specifically to connect to the RIVA/ViPEC FX-SHO/FZ Pro-Series
ECU via a waterproof factory connector. O2 sensor installs into stock exhaust
pipe using our precision machined Exhaust A/F Sensor Mount. The LC-1 is
more accurate than conventional designs costing many times as much, and
its self-calibrating circuitry can compensate for changes in temperature,
altitude and sensor condition.
Key Benefits Include:
* Fully digital wideband controller.
* Auto calibration capability to compensate for changes in temperature,
altitude, and sensor condition.
* Plugs directly into RIVA/ViPEC ECU harness.
* Includes Bosch LSU 4.2 02 sensor.
Description
RIVA LC1 Wideband Lambda Controller
Exhaust Air/Fuel Ratio Sensor Mount
Part No.
RY11540-LC1-6S5
RY15-AFSB
RIVA
EXHAUST
AIR/FUEL
RATIO
SENSOR
MOUNTS
NOTE: RIVA Pro-Series ECU is for competition use only.
Description
Riva/Vipec FX-SHO/FZR Pro-Series ECU
Part No.
RY11840-01-C
RIVA FX-SHO/FZ
BOOST CLAMP
The LC-1 is a complete wideband
Lambda controller built into a sealed
cable and wired specifically to connect to the RIVA/ViPEC FX-SHO/FZ ProSeries ECU via a waterproof factory connector. O2 sensor installs into stock
exhaust pipe using our precision machined Exhaust A/F Sensor Mount. The
LC-1 is more accurate than conventional designs costing many times as
much, and its self-calibrating circuitry can compensate for changes in temperature, altitude and sensor condition.
Description
RIVA LC1 Wideband Lambda Controller
Part No.
RY11740-BC-6S5
NGK SPECIAL
SPARK PLUGS
FOR FOUR
STROKE ENGINES
Description
Yamaha FX SHO/FX Cruiser
SHO/FZR (10 plugs per box)
Part No.
LFR6A
Riva’s precision
machined stainless steel exhaust O2 sensor mounts install easily into exhaust
system allowing use of air/fuel ratio sensors. Simple installation replaces OEM
plug with no modifications or special tools.
Description
RIVA Exhaust Air/Fuel Ratio Sensor Mounts
Part No.
RY15-AFSB
R&D
FX-SHO/FZR/FZS
O2 SENSOR
MOUNT KIT
The new R&D O2 sensor mount
kit makes installing an AFR
gauge a breeze on the Yamaha
FX-SHO, FZR, FZS, FX140, HO,
GPR, and VX110. It simply
replaces the OEM plug and
installs directly into the OEM pipe without any modifications. Kit comes complete with installation tool. AFR gauge sold separately.
Description
FX-SHO/FZR/FZS/FX140/HO/GPR/VX110/VXR/VXS
O2 Sensor Mount Kit
Part No.
332-18010
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
Part No.
RY1000-6S5-86
RY1000-6S5-8.6-020
RY1000-6S5-8.6-040
R&D HIGH
PERFORMANCE FORGED
PISTON KITS
R&D recommends upgrading to our High Performance Pistons and Rods in
applications producing over 300 H.P. @ sustained RPM's 8,000+.
R&D/JE Pistons
8.6-1 Compression OEM Replacement for SHO/FZR
9.5-1 Compression
10.5-1 Compression
11-1 Compression OEM Replacement for VXR/VXS
R&D/CP Pistons
8.6-1 Compression OEM Replacement for SHO/FZR
9.5-1 Compression
10.5-1 Compression
11-1 Compression OEM Replacement for VXR/VXS
Part No.
432-18861
432-18951
432-18105
432-18111
Part No.
432-19861
432-19951
432-19105
432-19111
R&D/CARRILLO HIGH
PERFORMANCE RODS
Carrillo is recognized as one of the finest
manufactures of connecting rods for high
performance engines. Carrillo connecting
rods are a precision, high strength, quality
product that reflects the optimum balance between lightweight and durability.
The Light weight forged design is substantially stronger and lighter than the
OEM rod and will deliver the strength needed to perform reliably under high
horsepower supercharged and turbo applications. R&D recommends upgrading to performance rods when using the R&D Monster C3-11 & C5-11
Supercharger Wheel or R&D Turbo Kit. Rod kit comes complete with Silicone
Bronze wrist pin bushing and high strength fasteners.
R&D recommends upgrading to our High Performance Pistons and Rods in
applications producing over 300 H.P. @ sustained RPM's 8,000+.
Description
Part No.
R&D/Carrillo High Performance Rods (4 Rod Set)
672-18000
RIVA PRO-SERIES
4-STROKE CYLINDER
HEAD STUD KITS
Riva’s ultra high strength cylinder head
stud kit is essential equipment when
upgrading internal components on your high boost Yamaha engine. Precision
machined from premium grade 8740 alloy and heat treated to exacting tolerances, these studs dramatically increase reliability & ease of maintenance.
Key Benefits Include:
• Superior material & heat treat process provide 10X better fatigue strength
than OEM bolts.
• Studs provide improved alignment of cylinder head and gasket for increased
reliability and ease of maintenance.
• More accurate & consistent torque loading provides a more uniform
clamping force on head gasket.
• Helps prevent blown head gaskets and assures optimum engine sealing.
Description
RIVA Pro-Series Cylinder Head Stud Kits
FX-SHO/FZR/FZS
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
• Direct replacement piston kits for High H.P. applications
• High quality forged materials replace low performance cast
• Improved ring seal with Nascar Style ring sets
• Increased RPM’s and horsepower by reducing weight
• Works great with high boost compressor wheels and turbo kits
• Retains O.E.M. wrist pins
• Four pistons per kit
Part No.
SHO/FZR High Performance Racing Cylinder Sleeves 432-18000
LA Sleeve Yamaha 1.8L Engine Cylinder Sleeve
YA-5688
BODY
R&D Yamaha Forged Racing Piston Kits
have been developed for the hard core
race enthusiasts or precision engine
builders who are looking to gain maximum horsepower and reliability from their racing engines. R&D offers high
quality forged aluminum, heat treated, and CNC machined racing pistons in
stock 8.6-1, 9.5-1, 10.5-1 and 11-1 compression ratios to replace O.E.M. cast
aluminum pistons known to be less reliable in high performance, high heat
conditions. High horsepower marine engines with high boost pressures are
more prone to have detonation over conventional racing engines due to sustained loads. Forged pistons in marine applications are a must. What ever
performance platform you are planning to build, trust the pros at R&D with all
your compression ratio, boost, and engine management needs or questions.
Description
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
FX SHO/FZR/FZS (8.6:1/STD)
FX SHO/FZR/FZS (8.6:1/.020)
FX SHO/FZR/FZS (8.6:1/.040)
*Sold individually - this is not a set.
EXHAUST
8.6 to 1 Compression
ENGINE/
GASKETS
Key Features Include:
• CNC machined from high strength/lightweight forgings.
• Optimized dome design for efficient combustion.
• Improved lubrication hole placement for reduced friction.
• Premium low friction ring package.
• High-strength tool steel wrist pins machined from special tool
steel bar stock & heat treated.
• Carbon steel wire locks.
• Direct replacement diameter plus 2 oversizes available.
R&D High Performance Racing Sleeves are
made to precise specifications specific for
the Yamaha FZR/SHO Supercharged engine. R&D Racing Sleeves install
easily and properly using the flanged “top hang” register design. The “top
hang” design when installed and seated properly will not drop or slip which
will allow 100 percent head gasket contact for a positive head gasket seal.
R&D Racing Sleeves are manufactured from the highest grades of centrifugally cast “Molly 2000” Chrome Molly Iron Alloy to provide superior strength
and hardness. Trouble free installation, boring, and honing using kit supplied
installation instructions and tips on final hone specifications for O.E.M. cast
and R&D Forged Racing Piston Kits are included. When the time comes to
repair wavy, scored, seized, or worn cylinders trust the pros at R&D. We have
been re-sleeving race engines for over 40 years. Sleeves are sold individually.
INATKE
SYSTEMS
Riva’s forged racing pistons deliver maximum reliability and performance in high
boost & turbo applications. High strength
piston kits include premium ring package,
tool steel wrist pin & carbon steel wire locks.
YAMAHA
4 STROKE
FZR HIGH PERFORMANCE
RACING CYLINDER
SLEEVES YAMAHA
1.8L ENGINE
RIVA PRO-SERIES
4-STROKE RACING
PISTONS
Part No.
RY10040-HSK
43
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
R&D HIGH PERFORMANCE
DUAL VALVE SPRING KIT
R&D has developed an economical solution for
upgrading the valve train by offering a series of
upgrade parts that will work great with the
O.E.M. retainer and valve seals. R&D has
documented that the seat tension or pressure
on the stock springs is a low 52-55 pounds,
and coil bind on the stock springs occurs .050” after full lift on the stock cams. As
an industry rule or standard, as boost levels are increased to the engine, the valve
spring seat pressure should be increased 1-2 pounds per pound of boost. As an
industry rule, as RPM'S are increased, the spring pressure at full lift should be
increased as well to reduce or eliminate valve float at high rpm frequencies. With
the stock springs “short lift travel” shimming is NOT an option. Valve Springs MUST
be upgraded. Also to consider is valve spring travel at full cam lift, and to have
enough spring clearance freedom to run high performance camshafts or add additional spring tension pressures without coil bind issues. The R&D spring kit parts
were developed and used with stock retainers during the 2009 season and have
proven their performance with an APBA/IJSBA Pro Open National Championship.
R&D dual springs are a “lightweight design” and manufactured from ultra clean,
high tensile material with multi step surface treatments to improve fatigue strength
and reliability. NOTE: R&D Spring Kits must use the R&D Bottom Spring Retainer
Cups kit Pt. # 612-93006 for proper assembly and seat pressures!
Engine Tuning Features
• 70-75 pounds at seat, 140-150 pounds at full lift (standard spec.)
• Shim friendly, add R&D spring collar base shims to add 2 pounds per .010 shim
• Allows the use of higher lift cams (up to +.080)
• Linear spring pressure curve allows smooth precision valve control
• High performance materials and surface finishes add to reliability
Description
R&D High Perf Dual Valve Spring Kit (16 per kit)
R&D offers High Performance Valve Stem Seal Kits
manufactured from only the best high quality Viton
rubber materials that will resist high valve guide and
oil temperatures to maintain a good valve seal in all
high rpm, high performance applications. When valve springs are changed out or
periodic head service work is being performed, trust R&D Valve Stem Seal Kits at
any performance level.
Description
R&D High Performance Valve Stem Seal Kit
Our high quality viton seals are extremely resistant to heat and abrasion.
Superior sealing keeps unwanted oil from contaminating combustion chambers and prevents air leakage through valve guides. A precision seal removal
& installation tool (RY19040-VST) is available separately. Sold in sets of 16.
Description
RIVA Yamaha 1.8L Engine Performance
Valve Seals
Description
R&D .010” Thick Shim Kit (set of 16)
R&D .020” Thick Shim Kit (set of 16)
R&D .030” Thick Shim Kit (set of 16)
Part No.
612-93003
612-93004
612-93005
R&D HIGH
PERFORMANCE
BOTTOM SPRING
RETAINER CUPS
R&D spring retainer cups will install
under the R&D valve spring and support and house the bottom of the spring
securely. The R&D Spring Retainer Cups must be used with the R&D spring
kits for proper assembly. Use R&D Valve Spring Shim Kits to fine tune valve
spring seat pressure.
Part No.
RY19040-PVS
VA YAMAHA
1.8L ENGINE
VALVE
RETAINER
UPGRADE KIT
R&D HIGH PERFORMANCE
VALVE SHIM KIT
The R&D spring base collar “shims” offer
precision valve spring tension shimming to fine
tune spring seat pressures based on boost
pressures the engine will run at. The R&D shim
kits are offered in the thicknesses of .010”, .020”, and .030”.
Part No.
612-93007
RIVA YAMAHA 1.8L
ENGINE PERFORMANCE
VALVE SEALS
Part No.
612-93001
Description
Part No.
R&D High Perf Bottom Spring Retainer Cups (set of 16) 612-93006
44
R&D HIGH PERFORMANCE
VALVE STEM SEAL KIT
Our Valve Retainer
Upgrade Kit increases the reliability of your engine by reducing the possibility
of valve float at high rpm. Includes 16 lightweight, precision-machined titanium valve retainers. A must for IJSBA & APBA Stock Class race craft.
NOTE: For modified engines (Stage 3 & above) we recommend the complete
RIVA Valve Train Upgrade Kit (part # Ry19040-VTU).
Description
RIVA Yamaha 1.8L Engine Valve Retainer
Upgrade Kit
Part No.
RY19040-SRU
RIVA VALVE TRAIN
UPGRADE KIT
Riva’s Valve Train Upgrade Kits
increase the reliability of your modified
engine by reducing the possibility of
valve float at high rpm. Includes lightweight, precision-machined titanium
valve retainers, racing valve springs,
and base washers.
Description
RIVA FX-SHO/FZR/FZS Valve Train Upgrade Kit
Part No.
RY19040-VTU
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
R&D VALVE STEM
CONCENTRICITY GAUGE
Key Features:
• Stronger & lighter than stock valves.
• Redesigned valve heads for improved air flow & strength.
• High grade stainless intake valves resist corrosion.
• Inconel exhaust valves resist heat from high boost applications.
• Valve stems are hard-chrome plated for improved wear.
• Includes high strength valve locks.
• Sold in sets of 16 (8 Intake/8 Exhaust).
Description
RIVA Yamaha High Performance Valve Set
Part No.
RY19040-HPV-0
(Standard/Drop-in)
RIVA Yamaha High Performance Valve Set
RY19040-HPV-1:1
(+1mm Intake / +1mm Exhaust)
RIVA YAMAHA 1.8L
ENGINE VALVE SEAL TOOL
This handy tool provides easy removal and installation of valve stem seals on
Yamaha 1.8L engines. Allows seal installation during fitting of valve train
upgrade kit without removing cylinder head.
FZR VALVE SPRING
COMPRESSION TOOL
KIT
The R&D Valve Spring Compression
Tool Kit allows easy removal of the
intake or exhaust valve springs and
keepers without removing the cylinder
head. R&D recommends using the compression adapter from a compression
gauge kit to pressurize cylinder keeping valves in place during removal of
springs and keepers.
Description
FZR Valve Spring Compression Tool Kit
Part No.
612-92013
FZR CAM TENSIONER TOOL
Key features:
• Prevents seal distortion & gouging.
• Precision machined from 6061 aluminum & anodized.
• Knurled handle for positive grip.
Description
RIVA Yamaha 1.8L Engine Valve Seal Tool
Part No.
RY19040-VCT
Part No.
RY19040-VST
The R&D Cam Tensioner Tool is designed to
mechanically spring preload the cam chain in
order to set and verify cam timing. This eliminates the process of pressurizing the hydraulic
cam tensioner to verify cam timing.
Description
Part No.
FZR Cam Tensioner Tool
612-92015
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Removal
Description
RIVA Valve Compression Tool
Fits Yamaha 1.8L & Kawasaki 1.5L 4-stroke
BODY
Installation
RIVA VALVE COMPRESSION TOOL
Riva’s overhead Valve Compression Tool allows easy removal of valve springs
and keepers without removing cylinder head. Includes compression adapter to
pressurize cylinder keeping valves in place during removal of stock springs
and keepers. Fits both Yamaha 1.8L & Kawasaki 1.5L 4-stroke engines.
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Drop-In Valve Kits: Standard size drop-in direct replacement valves require
no machining of cylinder head.
Oversiz ed Valve Kits: +1mm Intake/+1mm Exhaust valves deliver more air
flow (requires machining of cylinder head).
EXHAUST
Part No.
612-80010
ENGINE/
GASKETS
Description
R&D Valve Stem Concentricity Gauge
INATKE
SYSTEMS
RIVA High Performance Valve Kits are
engineered to improve reliability and performance
in high-boost supercharged & turbocharged
engines. Intake valves are built from high grade
EV-8 (24-4N) stainless that is extremely resistant
to corrosion. Exhaust valves are built from inconel
alloy (IN-751) that is highly resistant to heat
damage. Valve heads have been redesigned for increased air flow and
durability. Valve stems feature hard-chrome plating for superior wear &
lubricity. Kits include high strength valve locks, precision machined from 4130
chromoly.
YAMAHA
4 STROKE
RIVA YAMAHA HIGH
PERFORMANCE VALVE SET
The R&D Valve Stem Concentricity Gauge
is a testing tool to check the roundness
and trueness of valves. Small valves can
distort or bend from heat produced in high
performance supercharged or turbo
charged engines. To achieve a perfect
seal on the seat the valve needs to be concentric and true in every dimension.
Gauge is fully adjustable to accommodate a variety of valve sizes and
features a rigid, positive stop that can be set once and the trueness for an
entire set of valves can be measured. Kit comes complete with dial indicator
accurate to .001”. This is a must have tool for any engine builder to get the
most out of your high performance 4 stroke engine.
45
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
R&D YAMAHA FZ/FZR/SHO
RC1 RACING CAM KIT
R&D YAMAHA FZ/FZR/SHO
RC2 RACING CAM KIT
R&D’s RC1 Recreational/Racing Camshaft kit
offers a great boost in horsepower for the
recreational rider/racer who wants as much lift
and duration that can be “Bolted In” without valve
spring changes or valve guide machining. The
R&D RC1 will install and work well with O.E.M.
valve springs and retainers. The RC1 is a great
choice for recreational and offshore riding or
racing targeting the 7500-8500 RPM range for top
end power while also improving low and mid
range performance. The secret to the R&D cam
lobe is in the precision grind finish on the cams
base circle and duration at .050”. R&D maintains
strict specifications in this area of the cam lobe
which is the key to having strong vacuum, a great
idle tune, and clean acceleration performance.
R&D’s new RC2 Racing Camshaft kit offers a
serious boost in horsepower for the racer who
wants as much lift and duration that can be
safely “Bolted In” without valve guide or spring
base machining. The R&D RC2 Cam lobe profile has all of the same features in concept and
design as our RC1 recreational lobe, accept for
the increased lift and duration. The secret to the
R&D cam lobe is in the precision grind finish on
the cams base circle and duration at .050”.
R&D maintains strict specifications in this area
of the cam lobe which is the key to having
strong vacuum, a great idle tune, and clean
acceleration performance.
Overall lobe Lift and Durations are increased to allow as much lift as possible
and still run O.E.M. “uncut” valve guides. R&D has improved the lobe profile
with “state-of-the-art” technologies that will reduce valve lifter friction and
improve valve lifter wear. The R&D “boost friendly” lobe profiles increased lift
and duration will produce a noticeable horsepower increases and work well
with C1, C3, and C5 Monster Wheels and also work well with R&D R1, R2,
and R3 ECU Reprogramming Services. R&D RC1 custom cams can be
installed easily and shimmed with basic hand tools and the O.E.M. service
manual in as little as two hours without the removal of the head, or any valve
spring or retainer parts. Call R&D today for further details and specifications
for all your camshaft and valve train upgrades.
• Aggressive throttle response, increased overall horsepower
• Increased rpm performance (150-200 RPM Gain)
• Increased lift and duration (.368” lift and 6° degrees more duration)
• LC and LSA tunable (with R&D Cam Gears)
• 10-15 Bolt on Horsepower up grade
• R&D R1, R2 and R3 ECU Compatible
• Works well with R&D Valve Spring Kit upgrades
• Easy installation
NOTE: The R&D RC1 Recreational Camshaft Grind Specifications have been
extensively endurance tested to be the best lobe profile for recreational riding
or offshore racing. The lift and duration are similar to the Yamaha 1800 N.A.
cam with a total lift average of .368”. The duration on the RC1 cam is less at
.050” lift over the N.A., however, the same 6° degree duration advantage is in
the recipe. That puts the RC1 comparable on lift, equal on overall duration
and a strong low end vacuum to allow the use of R1, R2, and R3 ECU’s.
R&D has worked hard in the duration curve area of the cam paying careful
attention to the duration at .050” and overall added duration.
The R&D recreational camshaft kit is a performance modification regrind that
is performed in a normal 2-3 day turnaround to your existing camshaft cores.
R&D also stocks Camshaft kits that can be mail ordered direct with a
reasonable additional cam core charge. R&D camshaft specifications have
been performance tested against the 1800 naturally aspirated cams, and
clearly, there is no comparison in the tune ability area. R&D suggests that
the FZ/FZR, and SHO supercharged engines should benefit greatly from a
supercharger or turbocharger specific cam lobe profile and design. If
installing the R1 Cams with R&D Pro Tune Cam Timing Gears, a MoTeC or
comparable ECU must be used for tuning as aggressive lobe center changes
will reduce engine vacuum to lower than 15 inches and special custom tuning
will be required. R&D RC1 cams are a precision tolerance regrind. Valve
lifter re-shimming will be necessary. R&D will supply shimming specifications
with each cam set that will make valve adjustment easy. R&D recommends
the use of Hot Cams Shim Kits also available from R&D.
Description
R&D FZ/FZR/SHO RC1 Racing Cam Kit
46
Part No.
612-93009
Overall lobe Lift and Durations are increased to allow as much lift as possible
and still run O.E.M. “uncut” valve guides. R&D has improved the lobe profile
with “state of the art” technologies that will reduce valve lifter friction and
improve valve lifter wear. The R&D “boost friendly” lobe profiles increased lift
and duration will produce a noticeable horsepower gain and can also be
tuned to custom LSA (lobe separation angles) when using R&D “Pro Tune”
Cam Gears (Pt. # 612-93008). The R&D RC2 will produce noticeable
horsepower gains over R&D RC1 recreational cams with improved gains
from idle to wide open throttle. The RC2 Cam Kit really goes to work adding
top end pulling power in the 8500-9500 rpm zone. R&D custom cams can
be installed easily and shimmed with basic hand tools and the O.E.M. service
manual. R&D High Rev Valve Spring and shim kit parts are required for the
RC2 Cam Kit to work properly without coil bind damage. Call R&D today
for further details and specifications for all your camshaft and valve train
upgrades.
NOTE: The R&D RC2 requires the installation of R&D’s High Performance
Valve Spring kit as the O.E.M. valve springs will run into coil bind with the
added lift on the RC2 lobe profile. The RC2 will also require the use of a
stand alone ECU system such as a MoTeC M400 to custom tune the fuel
and ignition for optimum performance.
• Aggressive throttle response, increased overall horsepower
• Increased rpm performance ( RPM range increased to 9500)
• Increased CFM airflow
• Horsepower increase gain ( with R&D Cam Gears)
• Aftermarket ignition is required for custom tuning
• Works well with R&D Valve Spring Kit upgrades (Required)
• Easy installation • Bolt on 25+ Horsepower Upgrade
NOTE: The R&D RC2 Racing Camshaft Grind Specifications have been
Race Proven during the 2009 and 2010 racing seasons. No other camshaft
has more lift and more duration than the RC2. The nearest competitor to
date is the Yamaha 1800 N.A. Cam with a total lift average of .368”. That puts
the RC2 a full .020” higher. R&D has worked hard in the duration curve area
of the cam paying careful attention to the duration at .050” and overall added
duration. R&D is currently working on the RC3 Racing Cam available in mid
October. The R&D RC2 camshaft kit is a performance modification that is
performed in a normal 2-3 day turnaround to your existing camshaft cores.
R&D also stocks Camshaft kits that can be mail ordered direct with a
reasonable additional cam core charge. R&D suggests that the FZ/FZR,
and SHO supercharged engines should benefit greatly from a supercharger
or turbocharger specific cam lobe profile design and custom LC and LSA
set up.
Description
R&D FZ/FZR/SHO RC2 Racing Cam Kit
Part No.
612-93010
YAMAHA FX-SHO/FZ/VXR/VXS • ENGINE
R&D's new Cam Tensioner Gasket has a metal
reinforced center that enables it to be reusable.
Description
R&D Cam Tensioner Gasket
Part No.
080-21025
R&D FZR HIGH
PERFORMANCE
RACING HEAD GASKET
R&D High Performance Racing Head Gaskets
were developed to replace the O.E.M.
head gasket with a higher performing Multi Layer
Steel Stack Design (MLS), utilizing state of the art
materials proven to withstand extreme heat
generated from high cylinder pressures in high boost performance packages. Each
gasket is deep dual embossed (both sides) and Viton Coated to promote a positive
seal. Use the R&D Head Gasket with confidence in standard replacement situations or Pro Race Engines. Our race proven design maintains a positive seal with
up to 24 pounds of boost. Available in STD 86, 86.5, 87, 87.5, and 88mm bore
sizes. R&D also offers a “Super Thin” Gasket that will raise the compression level
when changing piston ratio is not an option.
NOTE: R&D also offers Custom R&D/CP High Performance pistons to fit any bore
size R&D Head Gasket. Gas porting also available upon request.
NOTE: NO need to re-torque the head bolts after initial installation which is a big
plus on DOHC engines where cams would otherwise need to be removed. Head
torque specifications are included with each gasket
Description
R&D 86mm HP Head Gasket .027” 3 Layer
R&D 86.5 HP Head Gasket .027” 3 Layer
R&D 87 HP Head Gasket .027” 3 Layer
R&D 87.5 HP Head Gasket .027” 3 Layer
R&D 88 HP Head Gasket .027” 3 Layer
R&D HP Head Gasket 0.18” 2 Layer
(Specify Bore Sz.)
Part No.
080-01800
080-01801
080-01802
080-01803
080-01804
080-01810
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
R&D CAM
TENSIONER GASKET
Part No.
RY10040-CHG-86
BODY
Part No.
612-93008
Description
Riva Pro-Series Head Gasket Standard
FX-SHO/FZR/FZS
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Description
R&D YAMAHA FZ/FZR/SHO Pro Tune Adjustable
Cam Gear Kit
Key Benefits Include:
• Three layer stainless construction for durability & corrosion resistance.
• Viton coated & embossed surfaces for maximum sealing between head and
cylinder block.
• Unique design promotes even torque load across sealing surface & requires
no re-torque.
EXHAUST
NOTE: R&D has determined that the O.E.M LCA is a WIDE 120 degrees
stock, with an intake cam lobe center of 122.5 degrees. Considering the
LCA timing facts, using the R&D Pro Tune Cam Gears to tune the cams will
generate huge performance power gains. R&D has found in testing that a
2.5 degree LCA change will act similar to a 1 pound boost addition. Tests
have proven that an R&D C1 or C3 compressor wheel and a 7 degree LCA
change can have the same performance advantages as a 15 pound compressor wheel. Call R&D for constant power upgrade information as we are
constantly at work looking for more.
Our Pro-Series Cylinder Head
Gaskets were developed to withstand severe heat & pressure generated by
high-boost and high horsepower applications delivering maximum reliability to
your racing engine.
ENGINE/
GASKETS
• Aggressive throttle response, increased overall horsepower
• Increased rpm performance (+200-300 RPM Gain)
• Boost Pressure Increase (+1 pound) • 15-25 Horsepower Increase
• Precision CNC Billet/Ground Cam Gears (lighter than stock)
• R&D R1, R2, and R3 ECU Compatible
• Works well with R&D Cam Regrind and Valve Spring Kit upgrades
• Easy installation • Bolt on Higher Horsepower Upgrade
RIVA PRO-SERIES
4-STROKE CYLINDER
HEAD GASKETS
INATKE
SYSTEMS
R&D’s Racing Cam Gear kit allows a huge boost in overall horsepower to be
gained by custom tuning the camshafts LCA (lobe separation angle) set up.
Tuning the LCA with R&D Pro Tune Cam Gears can add 200-300 RPM’s,
increased boost pressure, and 2-3 MPH to your existing engine package.
Adjusting the camshafts LCA is a very simple “BOLT IN” modification with the
R&D Pro Tune Adjustable Cam Gear Kit. Understanding the LCA concept
principle is fairly easy. A wide LCA like found in the SHO and FZR will
generally result in decreased valve overlap, later intake events, earlier
exhaust events, and high intake manifold pressures which produce great idle,
smooth accelerating with mild low and top end power. Wide LCA’s are great
for school buses and soccer mom vans. However, if strong mid range pull
and top end horsepower is what you’re looking for, then a narrower LCA will
need to be generated. The R&D Pro Tune Cam Gear Kit allows the LCA
(lobe separation) to be adjusted narrower which will generate increased valve
overlap, earlier intake events, and later exhaust events. Resulting in snappier
throttle response, increased mid range and top end power and more boost.
Why spend big money on optional camshaft kits (i.e. 1800 N.A. cams) that
have proven to offer too narrow of LCA compromising idle tune? Buy the
R&D Pro Tune Cam Gears designed specifically to improve overall power at
a fraction of the cost and provide an optimum overall tune. The R&D Cam
Gear Kit offers four possible LCA combinations that allow the cams to be
tuned depending on the type of riding or racing and type of fuel. In fact,
R&D has built a specific engine designated for degreeing, checking and
proving camshaft specifications. Depend on the Pro’s at R&D to deliver all
your horsepower needs.
YAMAHA
4 STROKE
R&D YAMAHA
FZ/FZR/SHO
PRO TUNE
ADJUSTABLE
CAM GEAR KIT
47
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • CONTROL
48
FZR
112-18001
R&D FZR AQUAVEIN
INTAKE GRATE
The huge FZR pump intake
demands strength and an extra
large wing for maximum hook up.
The new R&D FZR grate utilizes an
all new ultra strong 3 bar front
mount strut design to support a new "extra wide" forward mounted wing that
is guaranteed to top load the FZ pump with enough water to stay hooked up
and moving forward in the roughest water conditions. The new "SUPER
DEEP" race legal bars are the biggest and strongest we have ever built to
deliver unmatched strength. The new 3 bar concept and "Flat Faced" wide
wing proved out to provide superior cornering over previous single bar
designs. Big pump inlets need big grates, and that’s what we have built.
* For proper installation R&D recommends the use of the R&D Pump Shoe
Seal Kit (Pt. # 162-00007)
Description
R&D FZR Aquavein Intake Grate
FX SHO
112-18000
RIVA FZR/FZ
STAINLESS STEEL
TOP-LOADER INTAKE
GRATE
Our revolutionary new intake grate
for FZR/FZS delivers the ultimate in
speed, hook up & strength. All new
design features oversized top loader
wing and optimized inlet ramp for
closed course and offshore racing.
Bulletproof stainless steel construction makes this grate virtually indestructible and eliminates the need for additional restrictive support bars. Race bred
design significantly reduces cavitation and provides superior handling along
with unmatched durability in extreme conditions.
Description
Riva FX Stainless Steel Top-Loader Intake Grate
RIVA YAMAHA
INTAKE GRATE
Part No.
112-18001
R&D AQUAVEIN
INTAKE GRATE
Description
R&D FX SHO Aquavein Intake Grate
R&D VXR/VXS Aquavein Intake Grate
Part No.
112-18000
112-18020
Part No.
RY22050-1
Riva’s Top-Loader intake
grate improves hook up
and handling in rough
conditions. Center wing
eliminates prop spin and
RY22040
cavitation found with the
stock grate along with the
SHO/VXR’s tendency to drop on its nose when the throttle is let off at high
speeds. Powder coated to prevent corrosion.
Description
Riva FX-SHO/08-10 FX Intake Grate
Riva VXR/VXS Intake Grate
Part No.
RY22040
RY21030
R&D PUMP
SEAL KIT
R&D's new pump seal kit
stuffs up all the unwanted
cavities in the pump shoe
that aid in producing cavitation. This kit offers a way to
seal the pump shoe, which
will reduce cavitation and
increase pump efficiency
and performance.
Description
FX SHO Pump Seal Kit for OEM Intake Grate
FX SHO Pump Seal Kit for Riva Racing Intake Grate
FX SHO Pump Seal Kit for R&D Aquavein Intake Grate
FZR Pump Seal Kit for OEM Intake Grate
FZR Pump Seal Kit for R&D Aquavein Intake Grate
VXR Pump Seal Kit for Stock Scoop Grate
VXR Pump Seal Kit for R&D Aquavein Intake Grate
Part No.
162-00003
162-00004
162-00005
162-00006
162-00007
162-00008
162-00009
FX-SHO - RY25040
FZR/FZS - RY25050
RIVA PUMP SEAL KITS
Dramatically reduce cavitation and prop spin with our easy to install Pump
Seal Kits. Location specific, molded inserts fill the voids in OEM pump inlet
shoe that bleed air into pump causing cavitation. Recommended for modified
craft using aftermarket intake grates. Includes detailed installation instructions.
Description
Riva FX-SHO Pump Seal Kit
Riva FZR/FZS Pump Seal Kit
Part No.
RY25040
RY25050
YAMAHA FX-SHO/FZ/VXR/VXS • CONTROL
YAMAHA
4 STROKE
INATKE
SYSTEMS
ENGINE/
GASKETS
Key Benefits Include:
• Superior handling performance.
• Quicker planing & improved top speed.
• Reduced porposing.
• Improved straight line tracking at high speed.
• Race bred design.
• Improves acceleration, cornering and straight line handling.
• Turnable with included shims.
• Powder coated to prevent corrosion.
• IJSBA/APBA Race Legal.
Description
RIVA FX-SHO Performance Ride Plate
RIVA FZR/FZS Performance Ride Plate
RIVA VXR/VXS Performance Ride Plate
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
R&D HIGH
PERFORMANCE
RIDE PLATE
The new R&D SHO Pro
Series Ride Plate will meet
the demands in performance
whether being used for
weekend recreational riding,
closed course racing, or offshore competition. Increased top speed performance
of .50 to 1 MPH over stock, and compromises nothing when turned loose in rough
water conditions. Bow search with full fuel loads is alleviated completely.
• 1 MPH top speed improvement • Unique multi-step concept
• Improved straight line stability • Significantly improved cornering
• Reduced chine walking on high speed sweepers
• Drives through chop with superior stability
• Retains reverse gate mounting and operation
Description
R&D FX SHO High Performance Ride Plate
Part No.
122-18000
Part No.
RY21040
RY21050
RY21060
BODY
FX SHO
122-18000
Part No.
122-18001
122-18004
RIVA PERFORMANCE RIDE PLATE
Riva Ride Plate delivers the perfect balance of top speed and improved
handling in a variety of water conditions and speeds. Its race bred design
features deep channels for improved acceleration and traction in turns.
Provides excellent straightline stability at high speed with reduced porposing.
Utilizes stock ride plate support brackets and accepts OEM speedo sensor.
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Description
R&D FZR Pro Series Ride Plate
R&D VXR/VXS Pro Series Ride Plate
EXHAUST
R&D PRO SERIES RIDE PLATE
The new R&D Adjustable Ride Plate delivers a perfect balance of increased
top speed performance, improved cornering capabilities, and superb straight
line stability. The new adjustable design utilizes kit supplied shims to fine tune
the performance for a perfect balance of speed/handling for rider weight or
water conditions from drag to surf. Increased top speed performance and
compromises nothing when turned loose in rough water conditions. The
design utilizes the vital OEM hull protection stainless steel pads, which safely
disperse the pressure loads from the ride plate over a larger area on the hull.
The new R&D FZR Adjustable Pro Series Ride Plate will meet the demands
in performance whether being used for weekend recreational riding, closed
course racing, surf, or offshore competition. Made in the USA from cast
aluminum and powder coated for corrosion resistance.
• Top speed improvement
• Adjustable design
• Unique multi-step concept
• Improved straight line stability
• Significantly improved cornering
• Reduced chine walking on high speed sweepers
• Drives through chop with superior stability
• Retains reverse gate operation
2010 WORLD FINALS • LAKE HAVASU, AZ
PHOTO COURTESY OF JIN OMURA
49
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
YAMAHA FX-SHO/FZ/VXR/VXS • CONTROL
50
R&D YAMAHA
FX-SHO/FZR/FZS
SPONSON KIT
The new R&D Yamaha SHO Pro
Series Sponson Kit was designed
and developed with all new
generation performance concepts
in mind to deliver a whole new
level of handling and speed performance with offshore and closed course
race proven adjustability options. The R&D Pro Series Sponson Kits have
been extensively offshore, race track, and 1 and 2 up recreational tested to
guarantee a comfortable setting for any riding style or condition! The R&D
Sponson Kit will deliver higher top speed performance and a much smoother
and more predictable ride over O.E.M. sponsons. Low speed and high-speed
turns are a breeze with new found control. The secret to R&D’s new
generation concept is in the backing plate design with an aftermarket first,
low pressure, low friction concept that breaks up and relieves speed robbing
drag within the sponson’s backing plate channel. The new R&D design staggers the sponson blades fins water trapping area to pick up less water in the
front and more in the back. The stagger/step-up concept greatly reduces
chine walk in high speed corners, while allowing more rear end grip. There is
also a higher end recreational/race setting with enough grip for the best of
pro’s! Finally there is an aftermarket sponson kit that really does it all! More
top speed due to less drag, less chine walking, racer preferred rear end grip,
and unmatched straight line stability.
Description
R&D FX-SHO Sponson Kit
R&D FZR/FZS Sponson Kit
R&D VXR/VXS Sponson Kit
Part No.
122-01800
122-01801
122-01820
RIVA YAMAHA
FX-SHO/FZR/FZS/VX
SPONSON KIT
Unique blade design provides
a significant improvement to
the handling characteristics.
Reduces rough water hunting and
rolling sometimes experienced with
stock sponsons. Sponson depth is
adjustable to control the amount of influence they have on craft. Easily
installs to stock mounting points with our bulletproof mounting system that
features billet inserts in sponson fins.
Fits all Yamaha FX-SHO, FZR, FZS & VX models.
Description
Riva FX-SHO/FZR/FZS/VX Sponsons Kit
RIVA FZ PRO-SERIES STEERING SYSTEM
Introducing the ultimate race proven steering system for your Yamaha
FZR/FZS. Fully adjustable design features a dual tube steering head for
maximum strength & rigidity. Directly replaces bulky OEM mechanism with
a stronger & lighter unit that provides variable height and tilt positions.
Delivers a precision feel and the confidence to push your craft to the limit
with improved dependability and comfort. Bulletproof bar clamp will accept
any 7/8" handlebar or 1 1/8" bulge bar. Includes all necessary installation
hardware and instructions.
Key Features:
• Superior strength & rigidity over OEM system.
• Billet stainless steel steering shaft is much stronger than the OEM
aluminum shaft.
• Cutting edge race styling.
• Variable height and tilt adjustment.
• Accepts both 7/8" bars & 1 1/8" bulge bars.
• Billet steering arm features adjustable "quick turn" settings.
• Retains Off Throttle Steering system.
• Race tested & proven on 2010 IJSBA/APBA tours.
• All aluminum parts anodized to prevent corrosion.
• Standard 3.5" tubes provide adjustment +/- 1" from OEM low position.
• Optional 5-1/2" & 7-1/2" tubes provide additional height choices.
Description
RIVA FZ Pro-Series Steering System
Part No.
RY20050-U-3.5
Part No.
RY2625
WORX RACING
YAMAHA SHO/FZR/FZS
SPONSONS
Fitting WORX sponsons provide
unbelievable cornering, better control in the
rough and predictable inline tracking while
towing wakeboards or waterskiers. WORX
sponsons are easy to fit, look great and
bolt right into stock mounting holes.
Description
Worx FX-SHO Sponsons Kit
Worx FZR/FZS Sponsons Kit
Part No.
WR542
WR543
SATO ENGINEERING
FZR/FZS STEERING SYSTEM
This billet steering system is the ultimate upgrade for the new Yamaha FZ
watercraft. The system is extremely strong and allows the rider to change to
handlebars of their choice.
Description
Sato Engineering FZR/FZS Steering System
Part No.
SE-027020
YAMAHA FX-SHO/FZ/VXR/VXS • CONTROL
YAMAHA
4 STROKE
Part No.
RY20060-U
R&D FZR BILLET
STEERING
SYSTEM KITS
Part No.
512-18000
512-18001
512-18010
512-18012
R&D’s new Hydro Force Steering Nozzle for the FX-SHO/FZR/FZS/VXR/VXS
is a direct replacement nozzle. The new lengthened design delivers a full 1
MPH speed gain over stock. The adjustable pivot position improves the turning radius allowing you to carve tighter turns with a more positive feel.
Improved performance through speed, acceleration and handling.
Description
R&D FX-SHO/FZR/FZS/VXR/VXS
Hydro Force Steering Nozzle
Part No.
162-14000
R&D FX-SHO/FZR/FZS
VTS QUICK SHIFT
CAM KIT
The R&D FX-SHO/FZR/FZS VTS Trim Driver Cam is a cam device that installs
directly in place of the O.E.M. plastic VTS trim driver cam. The R&D cam is
designed to recalibrate the trim position amount from an O.E.M. 7 to 8 degree
per shift to a finer and speed friendly 4 degree per shift. The O.E.M. SHO neutral position setting is 85 degree or 5 degree up from horizontal zero. The new
recalibrated position with the new R&D Trim Cam is 87.5 degrees or 2.5 degree
up from horizontal zero. The R&D Trim Cam will deliver a more positive group of
adjustments that will allow much better turning capabilities, as well as finer
adjustments for rough water conditions. The R&D Trim Cam will work with the
O.E.M. trim nozzle assembly, or the R&D Auto Trim Kit.
Description
R&D FX-SHO/FZR/FZS VTS Trim Driver Cam Kit
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
R&D offers two types of Handlebars for the new billet steering system, MX Low
for short to average height pilots and MX high for taller pilots. Handlebars sold
separately. The R&D Steering System is the way to go when setting up the
ergonomic steering comfort “your way”. Available for FZR/FZS and SHO models.
• 3 pounds lighter than stock system
• Easy installation (1hour) includes all hardware and instructions
• Increases overall comfort and handling performance
• Allows custom bar setups (set up your way)
• Utilizes 7/8” diameter handlebars of our choice
• Adds a true “Factory Racing” look to your watercraft
R&D FX-SHO/FZR/FZS/VXR/VXS
HYDRO FORCE STEERING NOZZLE
BODY
The new R&D Billet Steering System
was developed and tested during the
2009 APBA/IJSBA National and World
Championships and is a proven
winner in design and performance.
R&D’s Billet design offers superior strength and lighter weight over the OEM
steering system. Utilizing a 7/8” MX handlebar, allows the rider to personalize
the bar setup to their liking. R&D chose the 7/8” diameter bar type over the Fat
bar, because of the space watercraft bars need for start/stop switches, VTS
switches, and custom trim lever systems. When using fat or taper bars, the bar
widths are forced wider than comfortable in a watercraft application.
Description
FZR / FZS Billet Steering System
FX-SHO Billet Steering System
R&D MX Low Bar
R&D MX High Bar
Part No.
162-18020
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Description
Pro-Series Steering System YAM VXR/VXS
Description
FX-SHO/FZR/FZS/VXR/VXS Auto Trim Nozzle Kit
EXHAUST
Key Features:
• Superior strength & rigidity over OEM system.
• Billet stainless steel steering shaft is much stronger than OEM aluminum shaft.
• Cutting edge race styling.
• Variable tilt adjustment.
• Accepts both 7/8" bars & 1-1/8" bulge bars.
• Billet steering arm features adjustable "quick turn" settings.
• Retains Off Throttle Steering system.
• Integrated throttle cable retention bracket.
• All aluminum parts anodized to prevent corrosion.
NOTE: Requires use of aftermarket handlebars.
The R&D FX-SHO/FZR/FZS Auto Trim Kit was developed to accommodate
the O.E.M. VTS Quick Shift System with a fully adjustable and fully automatic
trim system! The R&D Auto Trim automatically drops a rider preferred and
adjustable 2-8 degrees. Drive from turn to turn never worrying whether the trim
is in the best position for perfect turn negotiation! The R&D Auto Trim allows
you to set the trim up your way to carve perfect turn every time! For long
straight rides the R&D Auto Trim System works in conjunction with O.E.M VTS,
so stock trim settings are retained, while the R&D Auto Trim takes over in the
turns. The combination allows the best of both worlds for recreational and
closed course riding!
ENGINE/
GASKETS
Our VXR/VXS steering system directly replaces bulky OEM mechanism with a
stronger & lighter unit that provides variable tilt adjustment. Delivers a precision feel and the confidence to push your craft to the limit with improved
dependability and comfort. Bulletproof bar clamp will accept any aftermarket
7/8" handlebar or 1-1/8" bulge bar. Includes all necessary installation hardware
and instructions.
INATKE
SYSTEMS
R&D FX-SHO/FZR/FZS/VXR/VXS
AUTO TRIM NOZZLE KIT
RIVA VXR/VXS PRO-SERIES
STEERING SYSTEM
Part No.
162-18010
51
YAMAHA FX-SHO/FZ/VXR/VXS • PUMP
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
BODY
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
EXHAUST
ENGINE/
GASKETS
INTAKE
SYSTEMS
YAMAHA
4 STROKE
R&D FX-SHO/FZR/FZS/VXR/VXS
PERFORMANCE EXIT NOZZLE
52
The new R&D cast aluminum exit nozzle is designed
to fine tune the pump and prop to maximize
performance and rpm. The new R&D exit nozzle is
available in 2.5 and 5 degree up sweep angles. The 5
degree positive angle lightens the nose of the craft
and adds top speed; this is great for recreational use. The 2.5 degree delivers
improved performance in rough water conditions by producing more nose
pressure to drive the hull through the bumps; this design is perfect for closed
coarse and offshore competition. Both types are available in bore sizes of 80,
80.5, 81, and 81.5. *Custom bore sizes from 80 to 90 available at no extra
charge, specify size when ordering. The maintenance free R&D cast aluminum
and powder coated one piece construction exit nozzle is the better alternative
to a removable ring design. With the new R&D nozzle the OEM reliability and
safety is retained, because there is not a removable ring sleeve to vibrate
loose, falls out and gets wedged in the steering nozzle creating a whole new
definition to the term BUCKING.
**Custom bore sizes available at no extra charge, specify size when ordering**
Description
R&D Perf. Exit
R&D Perf. Exit
R&D Perf. Exit
R&D Perf. Exit
Nozzle
Nozzle
Nozzle
Nozzle
2.5
2.5
2.5
2.5
degree
degree
degree
degree
80mm
80.5mm
81mm
81.5mm
Description
R&D Perf. Exit Nozzle 5 degree 80mm
R&D Perf. Exit Nozzle 5 degree 80.5mm
R&D Perf. Exit Nozzle 5 degree 81mm
R&D FZR Perf. Exit Nozzle 5 degree 81.5mm
Part No.
162-82800
162-82805
162-82810
162-82815
Part No.
162-85800
162-85805
162-85810
162-85815
RIVA FX-SHO/FZ
PRO-SERIES REDUCTION
NOZZLE
SHO/FZR R&D
ANTI-CAVITATION
TRANSOM PLATE
MACHINING
MODIFICATION
R&D’s new SHO/FZR Anti-Cavitation
Transom Plate Machining Modification service is now available. The
engineers at R&D have been successful at reducing pump cavitation by
removing the restriction in the OEM Transom Plate. The OEM Transom Plate
has a 3mm taper that restricts water flow in front of the prop. Removing this
restriction significantly reduces cavitation and improves holeshot and hook
up with any prop type or diameter. The service includes line boring the
Transom Plate and blue printing the new pump shoe diameter to blend with
the R&D Aquavein Intake Grate, and the sealing surface of the transom
plate where it mounts the hull is also improved by plugging the OEM casting
pocket in the face of the Transom Plate with R&D’s Sure Seal Urethane
Material. R&D also offers the service to a new OEM Transom Plate available
for immediate shipping.
Description
Transom Plate Machining Service
Complete new FZR Transom Plate
w/Machining Service
Complete new SHO Transom Plate
w/Machining Service
Part No.
162-18004
162-18005
162-18006
Our Pro-Series Reduction Nozzle is ideal for
tuning your Yamaha pump combination
to maximize performance. Nozzle exit
diameter can be easily changed via
interchangeable ring system. Looking for more
RPM or acceleration power? Insert a larger
diameter ring. Want more top speed or less RPM? Install a smaller diameter
ring. Nozzle includes three precision-machined stainless steel rings in graduated sizes (81, 82 & 83mm). Additional ring sizes available.
Note: Nozzle eliminates water spout function to maximize performance and
conform to racing safety rules.
Description
RIVA FX-SHO/FZ Pro-Series Reduction Nozzle
Part No.
RY23040-N
R&D FX-SHO/FZR/FZS/VXR/VXS
ANTI-CAVITATION CONE
Our Pro-Series Reduction Nozzle is ideal for tuning
your Yamaha pump combination to maximize
performance. Nozzle exit diameter can be easily
changed via interchangeable ring system. Looking for more RPM or acceleration
power? Insert a larger diameter ring. Want more top speed or less RPM? Install
a smaller diameter ring. Nozzle includes three precision-machined stainless
steel rings in graduated sizes (81, 82 & 83mm). Additional ring sizes available.
Note: Nozzle eliminates water spout function to maximize performance and
conform to racing safety rules.
Description
Anti-Cavitation Cone
Part No.
162-18000
RIVA BILLET DRIVESHAFT
SLEEVE KITS
Our precision machined Billet Driveshaft Sleeve is a direct replacement for
the thin factory rubber hose that is prone to distortion and failure. Sleeve is
constructed of 6061 aluminum and is anodized to prevent corrosion. Kit
includes high quality silicon couplers and stainless steel clamps. This
upgraded sleeve kit is highly recommended for performance applications due
to increased pump pressure that accelerates failure of original rubber hose.
Description
Billet Driveshaft Sleeve Kit FX/FZ All
Billet Driveshaft Sleeve Kit VXR/VXS
Part No.
RY30040-DSS
RY30060-DSS
YAMAHA FX-SHO/FZ/VXR/VXS • PUMP
Inducer
Solas Recommends:
FX-SHO/FZ Stock Replacement Impeller
FX-SHO/FZ Limited Boat Replacement Impeller
Part No.
YS-DF-13/22R
Part No.
YS-DF-14/21
YS-DF-15/22
FX-SHO/FZR/FZS/VXR/VXS
IMPELLER SHAFT
HOLDER TOOL
Developed specifically for the FX-SHO/FZR/FZS
watercraft, this tool is required to change
the impeller. 20mm splined.
Description
FX-SHO/FZR/FZS/VXR/VXS Impeller Tool
Engine Mods
Stock
Limited
Supermod
Pitch
12/17
12/17
14/18
Part No.
SY440ID1217
SY440ID1217
SY440ID1418
FX-SHO/FZR/FZS/VXR/VXS
R&D PRO COMP. CLUTCH
SAVER BILLET
DRIVELINE COUPLERS
R&D Performance is proud to announce the
release of the new SHO/FZR Pro Comp.
Clutch Saver Driveline Couplers. The new
clutch saver design increases the rotational
mass of the 1800cc engine. The engineers at R&D added approximately 1.5
pounds of weight to the driveline couplers to increase the rotational mass of
the engine. The added mass dampens the moment of inertia and absorbs
shock that the supercharger clutch and pump impeller receive each time the
engine accelerates. The result is smoother engine performance with added
clutch life and reduced prop shock and cavitation. These precision couplers
are made from billet aircraft aluminum and CNC machined to exact tolerance.
Also available for MOD SHOP conversion hull kits.
Description
SHO/FZR/VXR/VXS
Part No.
612-01801
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Description
Riva Solas Dynafly Impeller 13/22R
Inducer
Inducer
Inducer
BODY
This all new impeller delivers
unmatched acceleration & top
speed in Yamaha FX-SHO/FZ
applications. The "R" Series
impeller is precision tuned to
RIVA specifications using a pitch block fixture. This offers a higher level of
consistency when matched with RIVA Performance Kits. Includes billet impeller
cone that locks solidly into place with 3 stainless set screws. Ideal for Riva
Stage 1 applications or higher levels of modification when matched with RIVA
Pro-Series FX-SHO/FZ Reduction Nozzle (part# RY23040-N).
Part No.
SY557525SWM1218
SY557525SWM1220
SY557525SWM1323
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
RIVA SOLAS
DYNAFLY
R-SERIES
IMPELLER
Pitch
12/18
12/20
13/23
EXHAUST
Part No.
SY557525SW1119
SY557525SW1219
SY557525SW1220
SY557525SW1320
SY557525SW1321
SY557525SW1322
SY557525SW1323
SY557525SW1324
SY557525SW1325
11/19
12/19
12/20
13/20
13/21
13/22
13/23
13/24
13/25
Engine Mods
Stock
Limited
Supermod
ENGINE/
GASKETS
Description
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Skat-Trak FX-SHO/FZR/FZS
Main Drive
Main Drive
Main Drive
INATKE
SYSTEMS
RIVA Racing carries the
complete line of Skat-Trak stainless
steel Swirl impellers for Yamaha
FX-SHO & FZ models. Let our
performance experts assist you
with matching the correct impeller with your performance application. Includes
a billet nose boot and impeller wrench.
The new Twin Prop design drives
of the line much quicker than the
traditional single prop, and offers
a substantial increase in rough
water hookup.
Main Drive
YAMAHA
4 STROKE
SKAT-TRAK
FX-SHO/FZR/VXR/VXS
155-75-25 SWIRL
IMPELLERS
SKAT-TRAK
FX-SHO/FZR
TWIN IMPELLERS
Part No.
TOOL #53
53
YAMAHA FX-SHO/FZ/VXR/VXS • BODY
YAMAHA
4 STROKE
RIVA PERFORMANCE
RECOMMENDATION PARTS LIST
INTAKE
SYSTEMS
YAMAHA FX-SHO - STAGE 1
67 MPH @ 7,500
Stage 1
70-71 MPH @ 7,600 RPM
Note: All testing performed with 1/3 tank of fuel; trim neutral.
ENGINE/
GASKETS
EXHAUST
STEERING WATERLINE ELECTRICAL DRIVE LINE
HANDLING
& CONTROLS /BILGE
BODY
CHEMICAL SERVICE TOOLS ACCESSORIES
/HARDWARE
PERFORMANCE DATA
Stock
Stage Performance Parts
Description
RIVA FZ BILLET MIRROR BLOCK-OFF KIT
Riva’s billet Block-off Kit covers the opening left in the hood when mirrors are
removed for competition. Enhances craft's sleek lines and aerodynamics. Easy
installation requires no special tools. Precision machined from billet aluminum
and anodized to prevent corrosion. Includes installation hardware.
Description
Riva FZR/FZS Billet Mirror Block-Off Kit
Riva’s billet Block-off
Kit covers the opening
left in the hood when mirrors are removed for competition. Enhances craft's
sleek lines and aerodynamics. Easy installation requires no special tools.
Precision machined from billet aluminum and anodized to prevent corrosion.
Includes rubber mounting pad & installation hardware. Fits all 2010-2011 VX
& 2011 VXR/VXS.
Description
RIVA VXR/VXS/VX Mirror Block-off Kit
1
1
1
1
1
1
1
67 MPH @ 7,500
Stage 1
70-71 MPH @ 7,600 RPM
Note: All testing performed with 1/3 tank of fuel; trim neutral.
Stage Performance Parts
Description
Quantity
Performance Power Filter Kit
Intake Manifold Upgrade Kit
Free Flow Exhaust Kit
Pump Seal Kit
Stainless Steel Intake Grate
R-Series DynaFly Impeller
Performance Ride Plate
1
1
1
1
1
1
1
Part No.
RY5-VXR-MB
Add 4 gallons of convenient
under-seat storage to your VX or
VXR/VXS watercraft. Durable
plastic storage tub removes
easily to allow access for
maintenance.
Fits all 2010-2011 VX & 2011 VXR/VXS
54
Part No.
RY4-RST-060
RY13040
RY12040-IMUK
RY16040
RY25040
RY22040
YS-DF-13/22R
RY21040
PERFORMANCE DATA
Stock
RIVA
VXR/VXS/VX
REAR STORAGE
TUB
Description
RIVA VXR/VXS/VX Rear Storage Tub
Part No.
YAMAHA FZR - STAGE 1
Part No.
RY5-FZ-MB
RIVA
VXR/VXS/VX
MIRROR
BLOCK-OFF
KIT
Quantity
Performance Power Filter Kit
Intake Manifold Upgrade Kit
Free Flow Exhaust Kit
Pump Seal Kit
Top-Loader Intake Grate
R-Series DynaFly Impeller
Performance Ride Plate
2011 APBA HOT PRODUCTS
MARK HAHN MEMORIAL HAVASU 300
Part No.
RY13040
RY12040-IMUK
RY16040
RY25050-1
RY22050-1
YS-DF-13/22R
RY21050
YAMAHA FX-SHO/FZ/VXR/VXS • SEAT COVER
FZS Series
GENUINE
Description
Jettrim FZR Spike Design Custom Seat Cover
Jettrim FZR Retro Design Custom Seat Cover
Jettrim FZS Retro Design Custom Seat Cover
Jettrim FZS Spike Design Custom Seat Cover
Jettrim FX-SHO Custom Design Seat Cover
Jettrim VXR Custom Design Seat Cover
Part No.
YFZR101
YFZR102
YFZS101
YFZS102
YSHO101
YVXR101
INATKE
SYSTEMS
Front: Kevlar Black
Top 1: Medium Slip Silver
Top 2: Smooth Grain Yellow
Rear Top: Medium Slip Black
Rear Tail: Smooth Grain Yellow
Side: Carbon Black
Tail: Medium Slip Black
Rear Side: Carbon Dark Silver
JETTRIM CUSTOM ORDER SEAT COVER
YAMAHA
4 STROKE
YFZS101-A
YFZS101-B
FZR Series
EXHAUST
PRE-COLORED HOT PRODUCTS
RECOMMENDED JETTRIM SEAT COVERS
ENGINE/
GASKETS
Front: Kevlar Black
Top 1: Medium Slip Silver
Top 2: Smooth Grain Red
Rear Top: Medium Slip Black
Rear Tail: Smooth Grain Red
Side: Carbon Black
Tail: Medium Slip Black
Rear Side: Carbon Dark Silver
The upholstery outline for your custom designed seat cover is
available in the Hot Products Price List.
YFZS102-B
Top: Black Diamond Plate Non-Slip Vinyl
Front & Rear Side: Carbon Black Large
Spike: Smooth Light Green Vinyl
Rear: Black Ostrich
Stitch: Green Thread on Top
YFZR101-C
Top: Medium Slip Silver Vinyl
Front & Rear Side: Carbon Black Large
Spike: Smooth Light Green Vinyl
Rear: Black Ostrich
Stitch: Blue Thread on Top
YFZR102-B
YVXR101-A
Top Front: Medium Slip Silver Vinyl
Top Rear: Medium Slip Black
Front Collar:
Carbon Dark Blue Vinyl
Center Band & Tail:
Carbon Dark Blue Vinyl
Side & Back Rest:
Smooth Black Vinyl
Stitch: Blue Thread on Top
BODY
Top: Medium Slip Black Vinyl
Front & Rear Side: Carbon Black Large
Front Collar & Band:
Smooth Light Green Vinyl
Rear: Smooth Light Green Vinyl
Stitch: Bright Green Thread on Top
VXR Series
DRIVE LINE ELECTRICAL WATERLINE STEERING
HANDLING
/BILGE & CONTROLS
Top 1: Medium Slip Silver
Top 2 & Rear Top:
Medium Slip Black
Rear Side: Smooth Grain White
Side 1: Kevlar Black
Spike: Smooth Grain Light Orange
Side 2: Smooth Grain White
Rear Tail: Carbon Black
YFZR101-B
YVXR101-B
YVXR101-C
Top Front & Rear:
Non Slip Black Diamond Plate Vinyl
Front Collar:
Smooth Grain Black Vinyl
Center Band & Tail:
Smooth Grain Black Vinyl
Side: Carbon Black
Back Rest: Bright Orange
Stitch: Orange Thread
ACCESSORIES SERVICE TOOLS CHEMICAL
/HARDWARE
Top Front & Rear:
Medium Slip Black Vinyl
Back Rest: Carbon Black
Front Collar: Silver Diamond Vinyl
Center Band & Tail:
Silver Diamond Vinyl
Side: Smooth Black Vinyl
Stitch: Silver & Black Thread
55