Siemens 5930 Product specifications

Efficient Networks Business Class
5930
Business Gateway
User Reference Guide
Part No. 107-5930-000
Efficient Networks®
Software License and Limited Warranty
 Copyright 2002, Efficient Networks, Inc.
All rights reserved. Printed in the U.S.A.
Efficient Networks and SpeedStream are registered trademarks, and the Efficient Networks logo is a trademark of Efficient
Networks, Inc. All other names may be trademarks, service marks or registered trademarks held by their respective companies.
This document is for information purposes only, Efficient Networks is not responsible for errors or omissions herein. Efficient
reserves the right to make changes to product specifications without notice.
Efficient Networks, Inc. – End User Software License and Warranty
INSTALLATION OF THE HARDWARE AND SOFTWARE PROVIDED BY EFFICIENT NETWORKS, INC. ("EFFICIENT") CONSTITUTES ACCEPTANCE BY YOU OF THE TERMS OF THE FOLLOWING SOFTWARE LICENSE AND LIMITED WARRENTY. IF YOU
DO NOT ACCEPT THESE TERMS, PLEASE RETURN THE HARDWARE AND SOFTWARE AND SOFTWARE IN ITS ORIGINAL
PACKAGING TO THE VENDOR FROM WHICH YOU PURCHASED IT FOR A FULL REFUND OF THE PURCHASE PRICE.
The following describes your license to use the software (the"Software") that has been provided with your EFFICIENT DSL customer premise
equipment ("Hardware") and the limited warranty that EFFICIENT provides on its Software and Hardware. EFFICIENT reserves any right not
expressly granted to the end user.
Software License
The Software is protected by copyright laws and international copyright treaties. The Software is licensed and not sold to you. The definition
od Software includes, but not limited to, system and operating software marketed by EFFICIENT, including firmware, embedded software, software provided on media, downloadable software, software for configuration or programmable logic elements, and all EFFICIENT maintenance
and diagnostic tools associated with the above mentioned software. Accordingly, while you own the media (such as CD ROM or floppy disk)
on which the software is recorded, EFFICIENT or its licensors retains ownership of the Software itself.
1. Grant of License. You may install and use one (and only one) copy of the Software in conjunction with the EFFICIENT provided Hardware.
You may make backup copies of the system configuration as required. If the Hardware is being installed on a network, you may install the Software on the network server or other server-side devise on which the Hardware is being installed and onto the client-side devices.
2. Restrictions. The license granted is a limited license. You may NOT:
• sublicense, assign, or distribute copies of the Software to others;
• decompile, reverse engineer, disassemble or otherwise reduce the Software or any part thereof to a human perceivable form;
• modify, adapt, translate or create derivative works based upon the Software or any part thereof; or
• rent, lease, loan or otherwise operate for profit the Software.
3. Transfer. You may transfer the Software only where you are also transferring the Hardware. In such cases, you must remove all copies of
the Software from any devices onto which you have installed it, and must ensure that the party to whom you transfer the Hardware receives this
License Agreement and Limited Warranty.
4. Upgrades Covered. This License covers the Software originally provided to you with the Hardware, and any additional software that you
may receive from EFFICIENT, whether delivered via tangible media (CD ROM or floppy disk), down loaded from EFFICIENT, or delivered
through customer support. Any such additional software shall be considered "Software" for all purposes under this License.
5. Export Law Assurances. You acknowledge that the Software may be subject to export control laws and regulations of the U.S.A. You confirm that you will not export or re-export the Software to any countries that are subject to export restrictions.
6. No Other Rights Granted. Other than the limited license expressly granted herein, no license, whether express or implied, by estoppel or
otherwise, is granted to any copyright, patent, trademark, trade secret, or other proprietary rights of EFFICIENT or its licensors.
7. Termination. Without limiting EFFICIENT’s other rights, EFFICIENT may terminate this license if you fail to comply with any of these
provisions. Upon termination, you must return the Software and all copies thereof.
Limited Warranty
The following limited warranties provided by EFFICIENT extend to the original end user of the Hardware/licensee of the Software and are not
assignable or transferable to any subsequent purchaser/licensee.
1. Hardware. EFFICIENT warrants that the Hardware will be free from defects in materials and workmanship and will perform substantially
in compliance with the user documentation relating to the Hardware for a period of one year from the date the original end user received the
Hardware.
2. Software. EFFICIENT warrants that the Software will perform substantially in compliance with the end user documentation provided with
the Hardware and Software for a period of ninety days from the date the original end user received the Hardware and Software. The end user is
responsible for the selection of Hardware and Software used in the end user’s network. Given the wide range of third-party hardware and applications, EFFICIENT does not warrant the compatibility or uninterrupted or error free operation of our Software with the end user’s systems or
network.
3. Exclusive Remedy. Your exclusive remedy and EFFICIENT’s exclusive obligation for breach of this limited warranty is, in EFFICIENT’s
sole option, either (a) a refund of the purchase price paid for the Hardware/Software or (b) repair or replacement of the Hardware/Software with
new or remanufactured products. Any replacement Hardware or Software will be warranted for the remainder of the original warranty period
or thirty days, which ever is longer.
4. Warranty Procedures. If a problem develops during the limited warranty period, the end user shall follow the procedure outlined below:
Α. Prior to returning a product under this warranty, the end user must first call EFFICIENT at (888) 286-9375, or send an email to EFFICIENT
at support@efficient.com to obtain a return materials authorization (RMA) number. RMAs are issued between 8:00 a.m. and 5:00 p.m. Central
Time, excluding weekends and holidays. The end user must provide the serial number(s) of the products in order to obtain an RMA.
Efficient Networks®
Software License and Limited Warranty
B. After receiving an RMA, the end user shall ship the product or defective component, including power supplies and cable, where applicable,
freight or postage prepaid and insured, to EFFICIENT at 4849 Alpha Road, Dallas Texas 75244, U.S.A. Within five (5) days notice from EFFICIENT, the end user shall provide EFFICIENT with any missing items or, at EFFICIENT’s sole option, EFFICIENT will either (a) replace
missing items and charge the end user or (b) return the product to the end user freight collect. The end user shall include a return address, daytime
phone number and/or fax. The RMA number must be clearly marked on the outside of the package.
C. Returned Products will be tested upon receipt by EFFICIENT. Products that pass all functional tests will be returned to the end user.
D. EFFICIENT will return the repaired or replacement Product to the end user at the address provided by the end user at EFFICIENT Network’s
expense. For Products shipped within the United States of America, EFFICIENT will use reasonable efforts to ensure delivery within five (5)
business days from the date received by EFFICIENT. Expedited service is available at additional cost to the end user.
E. Upon request from EFFICIENT, the end user must prove the date of the original purchase of the product by a dated bill of sale or dated
itemized receipt.
5. Limitations.
• The end user shall have no coverage or benefits under this limited warranty if the product has been subject to abnormal use, abnormal conditions, improper storage, exposure to moisture or dampness, unauthorized modifications, unauthorized repair, misuse, neglect, abuse, accident,
alteration, improper installation, or other acts which are not the fault of EFFICIENT, including acts of nature and damage caused by shipping.
• EFFICIENT will not honor, and will not consider the warranty voided, if: (1) the seal or serial number on the Product have been tampered
with or (2) there has been any attempted or actual repair or modification of the Product by anyone other than an EFFICIENT authorized service
provider.
• The limited warranty does not cover defects in appearance, cosmetic, decorative or structural items, including framing, and any non-operative
parts.
• EFFICIENT’s limit of liability under the limited warranty shall be the actual cash value of the product at the time the end user returns the
product for repair, determined by the price paid by the end user for the product less a reasonable amount for usage. EFFICIENT shall not be
liable for any other losses or damages.
• The end user will be billed for any parts or labor charges not covered by this limited warranty. The end user will be responsible for any expenses related to reinstallation of the product.
• THIS LIMITED WARRENTY IS THE ONLY WARRENTY EFFICIENT MAKES FOR THE PRODUCT AND SOFTWARE. TO THE
EXTENT ALLOWED BY LAW, NO OTHER WARRENTY APPLIES, WETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING
ANY WARRENTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
6. Out of Warranty Repair. Out of warranty repair is available for a fixed fee. Please contact EFFICIENT at the numbers provided above to
determine out of warranty repair rate. End users seeking out of warranty repair should contact EFFICIENT as described above to obtain an RMA
and to arrange for payment of the repair charge. All shipping charges will be billed to the end-user.
General Provisions
The following general provisions apply to the foregoing Software License and Limited Warranty.
1. No Modification. The foregoing Limited Warranty is the end user’s sole and exclusive remedy and is in lieu of all other warranties, express
or implied. No oral or written information or advice given by EFFICIENT or tis dealers, distributors, employees or agents shall in any way
extend, modify or add to the foregoing Software License and Limited Warranty. This Software License and Limited Warranty constitutes the
entire agreement between EFFICIENT and the end user, and supersedes all prior and contemporaneous representation, agreements or understandings, oral or written. This Software License and Limited Warranty may not be changed or amended except by a written instrument executed
by a duly authorized officer of EFFICIENT.
EFFICIENT neither assumes nor authorizes any authorized service center or any other person or entity to assume for it any other obligation or
liability beyond that which is expressly provided for in this Limited Warranty including the provider or seller of any extended warranty or service
agreement.
The Limited Warranty period for EFFICIENT supplied attachments and accessories is specifically defined within their own warranty cards and
packaging.
2. EXCLUSION OF INCIDENTAL, CONSEQUENTIAL AND OTHER DAMAGES. TO THE FULL EXTENT PERMITTED BY LAW,
IN NO EVENT SHALL EFFICIENT OR ITS LICENSORS BE LIABLE, WHETHER UNDER CONTRACT, WARRENTY, TORT OR ANY
OTHER THEORY OF LAW FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WHATSOEVER, INCLUDING
BUT NOT LIMITED TO DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRPUTION, PERSONAL INJURY, LOSS OR IMPAIRMENT OF DATA OR BUSINESS INFORMATION, EVEN IF EFFICIENT HAS BEEN NOTIFIED OF THE POSSIBILITY OF SUCH
DAMAGES. EFFICIENTS’S OR IT’S LICENSOR’S LIABILITY TO YOU (IF ANY) FOR ACTUAL DIRECT DAMAGES FOR ANY
CAUSE WHATSOEVER, AND REGARDLESS OF THE FORM OF THE ACTION, WILL BE LIMITED TO, AND SHALL NOT EXCEED,
THE AMOUNT PAID FOR THE HARDWARE/SOFTWARE.
3. General. This Software License and Limited Warranty will be covered by and construed in accordance with the laws of the State of Texas,
United States (excluding conflicts of laws rules), and shall insure to the benefit of EFFICIENT and its successor, assignees and legal representatives. If any provision of this Software License and Limited Warranty is held by a court of competent jurisdiction to be a invalid or unenforceable to any extent under applicable law, that provision will be enforced to the maximum extent permissible, and the remaining provisions of this
Software License and Limited Warranty will remain in full force and effect. Any notices or other communications to be sent to EFFICIENT
must be mailed by certified mail to the following address:
Efficient Networks, Inc.
4849 Alpha Road
Dallas, TX 75244
U.S.A.
Attn: Customer Service
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Table of Contents
Contents
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
PC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Network Service Provider Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Connecting Your Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Configuring Your Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Microsoft Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Apple Macintosh . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-15
Linux . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-19
Administration Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21
Easy Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Router Information Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Protocol Selection Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Point-to-Point Protocol over ATM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Point-to-Point Protocol over Ethernet over PPPoA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Point-to-Point over Ethernet over RFC 1483 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
RFC 1483 Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
RFC 1483 MAC Encapsulated Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Dynamic Host Configuration Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Local Area Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
5930 Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Hardware Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Software Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-4
Efficient Networks®
3
Table of Contents
Efficient Networks® 5930 Business Gateway
User Reference Guide
Contents
Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
4
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
CHAPTER 1
CHAPTER 1
INSTALLATION
Introduction
This User Reference Guide covers basic installation and setup of the 5930 Business
Class Router.
Installation Requirements
Package Contents
Your package should contain the items listed below. If you determine anything to be
damaged or missing, please contact the dealer from whom the equipment was
purchased.
•
One Efficient Networks 5930 Business Gateway
•
One Efficient Networks Documentation CD-ROM
•
One AC power supply module and cord
•
One Ethernet cable, RJ-45
•
One DSL cable, RJ-11, purple label
•
One RJ-45 to DB-9 serial port adapter (console)
•
Customer Release Notes
•
5930 Business Gateway Quick Start Guide
•
Safety and Certification document
PC Requirements
•
CD-ROM Drive
•
Ethernet network interface card
•
TCP/IP network protocol installed
•
Web browser
•
Terminal emulation software if you want to configure your router via your
computer’s serial port before placing it into service on a network.
Efficient Networks®
Page 1-1
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Network Service Provider Requirements
Your Network Service Provider will have sent you information to configure your 5930
for your DSL connection. Depending upon the type of service that you ordered, you
should have received at least some of the items from the following list:
•
DNS address
•
One or more LAN IP addresses and a subnet mask
•
Protocol to use, from one of the following:
•
–
PPP (Point-to-Point Protocol), with a user name and password
–
PPPoE (PPP over Ethernet)
–
RFC 1483 (SNAP Encapsulation)
–
RFC 1483 MER (MAC Encapsulated Routing, requiring a WAN gateway
address)
–
VCI (PVC) numbers
Network options:
–
Bridging
–
IP Routing (requires a WAN IP address and subnet mask)
Connecting Your Router
Step 1
Place your router in a location where it will be well ventilated. Do not stack it with
other devices or place it on carpet.
Step 2
Connect your PC directly to any of the router’s Ethernet ports using the RJ-45
cable provided. You may also connect additional Ethernet devices to the
router’s Ethernet ports.
Step 3
Connect your router to the DSL jack using the RJ-11 cable (purple label).
Step 4
Connect the router to an AC power supply using the power supply module and
locking power cord.
Task Complete
CAUTION:
To reduce the risk of fire, use only 26 AWG gauge telecommunication cord to connect
your DSL port on your router to a DSL telephone jack.
Page 1-2
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Configuring Your Computer
Your computer must be configured to use the TCP/IP protocol suite over the Internet,
and to accept Dynamic Host Configuration Protocol address assignments from your
router. Although the information and settings required to make such configurations is
standard, differences exist amongst the various computer operating systems in how
these configurations are presented and established. This chapter presents the TCP/
IP and DHCP configuration screens in the most popular operating systems, to guide
the reader through the configuration process for each operating system.
You can skip directly to the instructions for your computer operating system from the
following list:
•
•
•
Microsoft Windows
–
Windows 98, see page 1-4
–
Windows NT 4, see page 1-6
–
Windows 2000, see page 1-8
–
Windows ME, see page 1-11
–
Windows XP, see page 1-13
Apple Macintosh
–
Mac OS 9.x, see page 1-15
–
Mac OS X, see page 1-17
Linux OS, see page 1-19
Efficient Networks®
Page 1-3
Chapter 1: Installation
Efficient Networks® 5930 Business Gateway
User Reference Guide
Microsoft Windows
Windows 98
Step 1
On your desktop, right click on the Network Neighborhood icon.
Step 2
The Network dialog should appear. Under the Configuration tab, from the network
components installed, select TCP/IP.
Step 3
Click Properties to display TCP/IP properties.
Step 4
In the TCP/IP Properties dialog, select the IP Address tab.
Step 5
Under the IP Address tab, click to select the option to Obtain an IP address
automatically.
Page 1-4
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Step 6
Click OK.
Step 7
Click OK buttons to close each dialog.
Chapter 1: Installation
NOTE:
You may need to restart your PC for these changes to take effect.
Task Complete
Efficient Networks®
Page 1-5
Chapter 1: Installation
Efficient Networks® 5930 Business Gateway
User Reference Guide
Windows NT 4
Step 1
On your desktop, right click on the Network Neighborhood icon.
Step 2
The Network dialog should appear. Under the Protocols tab, from the network
protocols installed, select TCP/IP Protocol.
Step 3
Click Properties to display TCP/IP properties.
Step 4
In the Microstate TCP/IP Properties dialog, select the IP Address tab.
Step 5
Under the IP Address tab, click to select the option to Obtain an IP address from a
DHCP server.
Page 1-6
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Step 6
Click OK.
Step 7
Click OK buttons to close each dialog.
Chapter 1: Installation
NOTE:
You may need to restart your PC for these changes to take effect.
Task Complete
Efficient Networks®
Page 1-7
Chapter 1: Installation
Efficient Networks® 5930 Business Gateway
User Reference Guide
Windows 2000
Step 1
On your desktop, right click on the My Network Places icon.
Step 2
The Network and Dial-up Connections window should appear. Right click on the
Local Area Connection icon.
Step 3
From the menu, select Properties.
Step 4
The Local Area Connection Properties dialog should appear. From the list of
components, select Internet Protocol (TCP/IP).
Page 1-8
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Step 5
Click Properties.
Step 6
The Internet Protocol (TCP/IP) Properties dialog should appear. Select Obtain an IP
address automatically and Obtain DNS server address automatically.
Efficient Networks®
Page 1-9
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Step 7
Click OK.
Step 8
Click OK buttons to close each dialog.
NOTE:
You may need to restart your PC for these changes to take effect.
Task Complete
Page 1-10
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Windows ME
Step 1
On your desktop, right click on the Network Places icon (shown below).
Step 2
From the displayed menu, select Properties.
Step 3
The Network dialog should appear. Under the Configuration tab, from the network
components installed, select the TCP/IP Protocol associated with your network card
(see the example below).
Step 4
Click Properties to display TCP/IP properties.
Step 5
In the TCP/IP Properties dialog, select the IP Address tab.
Efficient Networks®
Page 1-11
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Step 6
Under the IP Address tab, click to select the option to Obtain an IP address
automatically.
Step 7
Click OK.
Step 8
Click OK buttons to close each dialog.
NOTE:
You may need to restart your PC for these changes to take effect.
Task Complete
Page 1-12
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Windows XP
Step 1
On your desktop, click on the My Network Places icon (shown below).
Step 2
The My Network Places screen should appear. Under the Network Tasks menu,
select View Network Connections.
Step 3
The Network Connections screen should appear. Click the Local Area Connection
icon.
Efficient Networks®
Page 1-13
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Step 4
The Local Area Connection Properties dialog should appear. From the list of items,
select Internet Protocol (TCP/IP).
Step 5
Click Properties.
Step 6
Click OK buttons to close each dialog.
NOTE:
You may need to restart your PC for these changes to take effect.
Task Complete
Page 1-14
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Apple Macintosh
To configure TCP/IP and DHCP on your Macintosh, please select your version of the
Mac OS from the following list:
•
Mac OS 9.x
•
Mac OS X
Mac OS 9.x
Step 1
Under the Apple menu, select Control Panels and then TCP/IP.
Efficient Networks®
Page 1-15
Chapter 1: Installation
Efficient Networks® 5930 Business Gateway
User Reference Guide
Step 2
The TCP/IP control panel should appear. From the Configure pull-down menu,
select: Using DHCP Server.
Step 3
Complete the fields shown with any information supplied by your service provider.
Step 4
Click on the upper left square in the menu bar to close the TCP/IP control panel.
Task Complete
Page 1-16
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Mac OS X
Step 1
Under the Apple menu, select System Preferences.
Step 2
The System Preferences window should appear. Click to select the Network icon.
Efficient Networks®
Page 1-17
Chapter 1: Installation
Efficient Networks® 5930 Business Gateway
User Reference Guide
Step 3
The Network window should appear. Select the TCP/IP tab.
Step 4
From the Configure pull-down menu, select Using DHCP.
Step 5
Enter any information supplied by your service provider.
Step 6
Click Save button to save and exit the Network window.
Task Complete
Page 1-18
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Linux
Step 1
From a terminal window, run linuxconfig.
Step 2
The Config dialog should appear. Enter any information specified by your service
provider in the fields under the appropriate Adapter tab.
Efficient Networks®
Page 1-19
Chapter 1: Installation
Efficient Networks® 5930 Business Gateway
User Reference Guide
Step 3
When settings are completed, Click Accept.
Step 4
To update the system status, ensure that the "Activate the changes" button is
highlighted, then click Act/Changes.
Task Complete
Page 1-20
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 1: Installation
Administration Login
The following procedure provides the steps for connecting to the router through the
Web Management Interface. If you prefer to connect via a console session, refer to
the Technical Reference Guide, “Establishing a Connection” on page 3-33.
Step 1
Using your web browser, enter the following default router address into the address
field of your browser: http://192.168.254.254/. A login dialog will be displayed.
Step 2
At the login prompt, enter the following default entries:
User Name: superuser
Password: admin
After you have logged into your router, a Change User Password screen (shown
below) will be displayed, prompting you to change your password. The password is
invalid by default for security purposes and must be changed to a unique password.
NOTE:
Passwords are case-sensitive and must be a minimum of 6 ASCII characters.
Efficient Networks®
Page 1-21
Chapter 1: Installation
Step 3
Efficient Networks® 5930 Business Gateway
User Reference Guide
To change the password,
a. Enter the new password in the field provided.
b. Re-enter the new password in the field provided.
c. Click Apply to save the password change.
With the password change, you have written a new account password to the router
and your current web-based connection will be invalid (it is still using the default
password). You will again be prompted with a login dialog to re-authenticate your
connection.
Step 4
At the login prompt, enter the new account information as required.
The Router Information Page will be displayed; you can proceed with Easy Setup.
Task Complete
Page 1-22
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 2: Easy Setup
CHAPTER 2
CHAPTER 2
EASY SETUP
The Easy Setup screens are designed to provide an easy step-by-step configuration
of the Wide Area Network (WAN) and Local Area Network (LAN). The information
required for completing these forms is obtained from your service provider. A broader
overview of the configuration parameters can be found in the Technical Reference
Guide.
The following Easy Setup procedure assumes you have made the appropriate
connections and have logged in to the router as illustrated in the Quick Start Guide.
During the Easy Setup procedure, you will configure parameters that provide
fundamental router operation. Once completed, you are provided links to learn more
about or perform configuration of advanced router features. If you need additional
information on using the Web Management Interface, refer to See “WEB
Management Interface” on page 8-1 of the Technical Reference Guide.
If you prefer to configure the router using the Command Line Interface, refer to the
Technical Reference Guide, Chapter 3, Installation and Setup.
Efficient Networks®
Page 2-1
Chapter 2: Easy Setup
Efficient Networks® 5930 Business Gateway
User Reference Guide
Router Information Page
The primary page in the Web User Interface is the Router Information page. This
screen displays basic router information and configuration settings. It also provides
links to other router setup and control forms. On the Router Information page, the
following information is presented:
•
Router Information - Including the model number, software version number
and options that have been enabled.
•
Router Configuration - Displays router configuration details such as LAN IP
address, WAN data and voice PVC (ATM), WAN protocol and WAN network
settings.
The following is a typical Router Information page:
To proceed with Easy Setup, click the Easy Setup link on the Router Information
page.
NOTE:
The Easy Setup procedure can be exited at any time during the configuration by
clicking Cancel on the bottom of the configuration page. If the procedure is cancelled,
no changes will be made and the WMI will return to the Router Information Page.
Page 2-2
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 2: Easy Setup
Protocol Selection Page
The Protocol Selection Page is the initial Easy Setup screen. This form is used to
entering and review information about Wide Area Network (WAN) settings.
On the Protocol Selection page, begin the Easy Setup procedure by performing the
following:
Step 1
Enter the ATM Permanent Virtual Circuit (PVC) information: VPI / VCI.
Step 2
Click the radio button to select the applicable WAN Protocol.
Step 3
Click Next to continue.
Task Complete
Efficient Networks®
Page 2-3
Chapter 2: Easy Setup
Efficient Networks® 5930 Business Gateway
User Reference Guide
Based on the selection in Step 2, proceed to the appropriate page:
•
’’Point-to-Point Protocol over ATM’’ at the bottom of this page.
•
“Point-to-Point Protocol over Ethernet over PPPoA” on page 2-6
•
“Point-to-Point over Ethernet over RFC 1483” on page 2-8
•
“RFC 1483 Networking” on page 2-10
•
“RFC 1483 MAC Encapsulated Routing” on page 2-12
Point-to-Point Protocol over ATM
Selection of Point-to-Point Protocol over ATM will display the following PPP
Configuration page.
To continue the Easy Setup procedure with PPP over ATM, continue with the
following steps:
Step 1
Enter the PPP User Name and Password in the fields provided.
A PPP username and password are required for authentication when the connection
is being established.
Page 2-4
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Step 2
Chapter 2: Easy Setup
Click to select the following PPP Networking options:
•
Bridging Enabled - Bridging will forward all traffic for remote hosts that is
not routed (non-IP) to the WAN. If Bridging Enabled is selected:
– Optional, click to select Only bridge PPPoE traffic. Proceed to Step 3.
Selection of this option will allow only PPPoE traffic to be bridged, all other traffic
will be dropped.
•
IP Routing Enabled - IP Routing will route all IP packets for remote hosts to
the WAN.
If IP Routing enabled is selected, click to select the following options:
Step 3
–
NAT Enabled - Network Address Translation (NAT) allows multiple
workstations on your LAN to share a single, public IP address. All
outgoing traffic appears to originate from the router’s IP address.
–
Block Net BIOS Traffic - NetBIOS is a PC networking protocol that can
keep network connections open inadvertently. To avoid excess
connection charges, such traffic should be blocked on any metered
network service.
Click Next to proceed with Easy Setup, Dynamic Host Configuration Protocol
configuration (see page 2-14).
Task Complete
Efficient Networks®
Page 2-5
Chapter 2: Easy Setup
Efficient Networks® 5930 Business Gateway
User Reference Guide
Point-to-Point Protocol over Ethernet over PPPoA
Selection of Point-to-Point Protocol over Ethernet over PPPoA will display the
following PPPoE Configuration page.
To continue the Easy Setup procedure with PPPoE, continue with the following steps:
Step 1
Enter the PPP User Name and Password in the field provided.
A PPP Username and password are required for authentication when the connection
is being established.
Step 2
Enter the PPPoE Service Name in the field provided.
PPPoE requires the domain name of your network service provider. Use * as a default
(for all services). Enter the domain name of your network service provider in the
Service Name field.
Step 3
Enter the timeout interval (measured in seconds) into the PPPoE Timer field.
PPPoE Timer will set a timeout interval for periods of inactivity. After the number of
seconds elapses, the PPP connection closes to limit timed connection charges from
your service provider. The default entry of “permanent” will keep the PPP connection
open constantly, with no timeout interval.
Step 4
As required, click to select PPPoE only Filter.
This selection will filter all traffic on the bridge to allow PPPoE only. Check this box if
you will only connect to your network service using PPPoE.
Page 2-6
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Step 5
Chapter 2: Easy Setup
Click Next to proceed with Easy Setup, Dynamic Host Configuration Protocol
configuration (see page 2-14).
Task Complete
Efficient Networks®
Page 2-7
Chapter 2: Easy Setup
Efficient Networks® 5930 Business Gateway
User Reference Guide
Point-to-Point over Ethernet over RFC 1483
Selection of Point-to-Point Protocol over Ethernet over RFC 1483 will display the
following PPPoE Configuration page.
To continue the Easy Setup procedure with PPPoE, continue with the following steps:
Step 1
Enter the PPP User Name and Password in the fields provided.
A PPP Username and password are required for authentication when the connection
is being established.
Step 2
Enter the PPPoE Service Name in the field provided.
PPPoE requires the domain name of your network service provider. Use * as a default
(for all services). Enter the domain name of your network service provider in the
Service Name field.
Step 3
Enter the timeout interval (measured in seconds) into the PPPoE Timer field.
PPPoE Timer will set a timeout interval for periods of inactivity. After the number of
seconds elapses, the PPP connection closes to limit timed connection charges from
your service provider. The default entry of “permanent” will keep the PPP connection
open constantly, with no timeout interval.
Step 4
As required, click to select PPPoE only Filter.
This selection will filter all traffic on the bridge to allow PPPoE only. Check this box if
you will only connect to your network service using PPPoE.
Page 2-8
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Step 5
Chapter 2: Easy Setup
Click Next to proceed with Easy Setup, Dynamic Host Configuration Protocol
configuration (see page 2-14).
Task Complete
Efficient Networks®
Page 2-9
Chapter 2: Easy Setup
Efficient Networks® 5930 Business Gateway
User Reference Guide
RFC 1483 Networking
Selection of RFC 1483 will display the following RFC 1483 Networking configuration
page.
To continue the Easy Setup procedure with RFC 1483, continue with the following
steps:
Step 1
Click to select one of the following.
•
Bridging enabled
•
IP routing enabled
If bridging is selected, all traffic to remote computers that is not routed will be
bridged. Next, continue to Step 2.
If IP routing enabled was selected, an IP address and subnet mask must be
obtained; proceed to Step 3.
NOTE:
If your Network Service Provider has not provided specifics for use in making these
settings, select the following IP Routing, Obtain configuration automatically from
WAN, and NAT enabled.
Step 2
Page 2-10
Optional, click to select Only bridge PPPoE traffic. Proceed to Step 4.
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 2: Easy Setup
Selection of this option will allow only PPPoE traffic to be bridged, all other traffic will
be dropped.
Step 3
Obtain an IP address, select from the two bulleted options below:
•
IP configuration automatically from a DHCP server on the WAN Using
DHCP.
(1) Click the radio button to select this option.
•
Configure IP Routing manually. This procedure requires the following:
(1) Click the radio button to select this option.
(2) Enter a unique IP Address in the field provided.
(3) Enter a unique Subnet Mask in the field provided.
If IP routing enabled is selected, click to select the following options:
Step 4
•
NAT Enabled - Network Address Translation (NAT) allows multiple
workstations on your LAN to share a single, public IP address. All outgoing
traffic appears to originate from the router’s IP address.
•
Block Net BIOS Traffic - NetBIOS is a PC networking protocol that can
keep network connections open inadvertently. To avoid excess connection
charges, such traffic should be blocked on any metered network service.
Click Next to proceed with Easy Setup, Dynamic Host Configuration Protocol
configuration (see page 2-14).
Task Complete
Efficient Networks®
Page 2-11
Chapter 2: Easy Setup
Efficient Networks® 5930 Business Gateway
User Reference Guide
RFC 1483 MAC Encapsulated Routing
Selection of RFC 1483 MAC Encapsulated Routing (MER) will display the following
RFC 1483 MER Networking configuration page.
To continue the Easy Setup procedure with RFC 1483 MER, continue with the
following steps:
Step 1
Click to select one of the following.
•
Bridging enabled
•
IP routing enabled
If bridging is selected, all traffic to remote computers that is not routed will be
bridged. Next, continue to Step 2.
If IP routing enabled was selected, an IP address and subnet mask must be
obtained; proceed to Step 3.
NOTE:
If your Network Service Provider has not provided specifics for use in making these
settings, select the following IP Routing, Obtain configuration automatically from
WAN, and NAT enabled.
Page 2-12
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Step 2
Chapter 2: Easy Setup
Optional, click to select Only bridge PPPoE traffic. Proceed to Step 4.
Selection of this option will allow only PPPoE traffic to be bridged, all other traffic will
be dropped.
Step 3
Obtain an IP address, select from the bulleted options below:
•
Obtain configuration automatically from WAN using DHCP
(1) Click the radio button to select this option.
•
Configure IP routing manually. This procedure requires the following:
(1) Click the radio button to select this option.
(2) Enter a unique IP Address in the field provided.
(3) Enter a unique Subnet Mask in the field provided.
If IP Routing enabled is selected, click to select the following options:
Step 4
•
NAT Enabled - Network Address Translation (NAT) allows multiple
workstations on your LAN to share a single, public IP address. All outgoing
traffic appears to originate from the router’s IP address.
•
Block Net BIOS Traffic - NetBIOS is a PC networking protocol that can
keep network connections open inadvertently. To avoid excess connection
charges, such traffic should be blocked on any metered network service.
Click Next to proceed with Easy Setup, Dynamic Host Configuration Protocol
configuration (see page 2-14).
Task Complete
Efficient Networks®
Page 2-13
Chapter 2: Easy Setup
Efficient Networks® 5930 Business Gateway
User Reference Guide
Dynamic Host Configuration Protocol
The next step in Easy Setup is configuration of DHCP. DHCP dynamically assigns IP
configuration information to PCs on the LAN, thus avoiding the need to set IP
configurations for each PC manually. For more information on DHCP, see “DHCP
(Dynamic Host Configuration Protocol)” on page 4-2.
This configuration form also provides for configuration of DNS (Domain Name
Service). DNS maps host names to IP addresses. The Easy Setup DHCP
Configuration page is shown below.
To continue the Easy Setup procedure by configuring DHCP, continue with the
following steps:
Step 1
Optional, click to select DHCP server enabled on the LAN.
Selecting this option will allow the DHCP server to dynamically assign IP address
information to all LAN-side machines.
Step 2
Configure Domain Name Service. Select one of the bulleted options
•
Obtain DNS information automatically
Selecting this option will enable the DNS on the router. The DNS server address will
be learned when DHCP client requests are placed over the WAN link.
•
Page 2-14
Configure DNS manually
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 2: Easy Setup
Selection of manual DNS configuration requires a minimum of one DNS Server
Address and a Domain Name. This information should be provided by the Service
Provided. Enter the DNS information as described below:
a. Enter the Domain Name in the field provided.
This sets the router’s DNS domain name
b. Enter the IP address of the Primary DNS Server in the field provided.
This establishes where DNS requests will be sent.
c. Optional, enter the IP address of the Secondary DNS Server in the field
provided.
This establishes where DNS requests will be sent if the primary DNS server is
unavailable.
d. Enter the IP address of the Primary WINS Server in the field provided.
The Windows Internet Naming Service (WINS) maps NetBIOS names to IP
addresses similar to DNS. This establishes where WINS requests will be sent.
e. Optional, enter the IP address of the Secondary WINS Server in the field
provided.
This establishes where WINS requests will be sent if the primary server is
unavailable.
Step 3
Click Next to continue Easy Setup.
Task Complete
Efficient Networks®
Page 2-15
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 2: Easy Setup
Local Area Network Configuration
The final screen in Easy Setup is for Local Area Network (LAN) configuration.
To continue the Easy Setup procedure by configuring the LAN IP address, continue
with the following steps:
Step 1
Enter the IP Address in the field provided.
The IP address is the network address of your router. This address must be globally
unique, unless NAT has been enabled.
Step 2
Enter the Subnet Mask in the field provided.
The subnet mask is used along with the IP address to determine if specific LAN IP
traffic should be forwarded to the WAN.
Step 3
Click Save and Reboot.
Changes made within the Easy Setup procedure will be saved and made persistent
across system reboot functions. The router will reboot with the new configuration
settings.
Step 4
On completion of the reboot process, you will be required to login. If after 3 minutes,
the Router Information Page is not displayed, click the link in the restart message to
establish the WMI connection at the new IP address. The message is shown below.
Your router will restart at http://192.168.61.19/. If your browser can not reload
automatically in 3 minutes, please click the link. Thanks for waiting...
Task Complete
Page 2-16
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 2: Easy Setup
Additional Features
Several additional features are available that provide custom system operation as
well as advanced router functions. To learn more about how to configure any of these
features, select from the list below.
•
User Management - The system supports role-based management of up to
15 users. Each user can have specified access and management privileges
as described in “User Authentication” on page 5-2 of the Technical Reference
Guide. User management through the Web Management Interface (WMI) is
also illustrated in “User Management” on page 8-17. The number of user
accounts can be increased through the optional Radius feature.
•
Access Control - The Access Control feature restricts administrative access
and control of your router to a select group of hosts. For additional
information and procedures, refer to “Controlling Remote Management” on
page 5-15 in the Technical Reference Guide.
•
DHCP - This feature manages your IP address pool. For additional
information, refer to the Technical Reference Guide, “DHCP (Dynamic Host
Configuration Protocol)” on page 4-2 or to configure the feature via the WMI,
“DCHP Configuration” on page 8-35.
•
NAT - Network Address Translation is used to translate addressing between
the Local and Wide Area Networks. Three types of NAT are available. For
more information, refer to the Technical Reference Guide, “Network Address
Translation (NAT)” on page 4-17 or to configure this feature via the WMI,
“NAT” on page 8-38.
•
SNMP - SNMP provides for the exchange of messages between a
management client and a management agent. These messages can be used
to gather system status information or to set operational parameters where
supported. SNMP is discussed in the Technical Reference Guide on page 72, or can be configured through the WMI as described in “SNMP” on page 841.
•
Router Clock - Allows you to adjust the router clock. This can be performed
via the WMI on the “Router Clock Page” on page 8-34.
•
Feature Activation - Optional system capabilities are available through the
use of software "keys". These keys are entered in the system to enable a
variety of system capabilities. To learn more about feature keys, “Key
Enabled Features” on page 4-29 of the Technical Reference Guide, or see
“Feature Activation” on page 8-26 for WMI procedures.
•
Firewalls - Two types of firewalls are available on the router, one an IP
filtering Firewall is described in “IP Filtering” on page 5-23 of the Technical
Reference Guide. Additionally, a key-enabled Stateful Firewall is available
which provides a more robust, session-based firewall. The Stateful Firewall is
described in the Technical Reference Guide, page 5-34.
Efficient Networks®
Page 2-17
Chapter 2: Easy Setup
Efficient Networks® 5930 Business Gateway
User Reference Guide
This page intentionally left blank.
Page 2-18
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 3: Frequently Asked Questions
CHAPTER 3
CHAPTER 3
FREQUENTLY ASKED QUESTIONS
Which cable do I use to connect a new LAN device to the router?
If you are connecting your LAN device to one of the Ethernet ports on your router, use
an RJ-45 cable.
The ports of the 5930 Ethernet switch will automatically sense whether the connection
is to a PC, or to another hub or switch.
Can I connect the router to a 100Base-T hub?
Yes. Use either a straight through or a crossover cable. The router switch will autosense the connection and adjust accordingly.
What is the router password?
The router provides a role-based management solution with one initial user account;
the default settings for this account are: username superuser and password admin.
You will be required to change the default password when you connect to the router
for the first time using these default parameters.
What security options do I have?
A number of security options are available both as standard and key enabled features.
These features include local security to protect access to the router, data security that
protects local and remote traffic, and network security that protects the integrity of the
network machines. For more information on the security features of your router, refer
to the Technical Reference Guide, Chapter 5, Security.
Can I have an FTP, Mail or Web server and use NAT?
Yes, but you need to configure your router appropriately using the NAT Setting screen
or the Command Line Interface (CLI). By entering a remote system or addServer command, you can add FTP, Mail, NetMeeting or Web servers to your LAN. These can
then be accessed from another LAN or the Internet while NAT is enabled.
Efficient Networks®
Page 3-1
Chapter 3: Frequently Asked Questions
Efficient Networks® 5930 Business Gateway
User Reference Guide
What is MER?
MER (MAC Encapsulated Routing) allows your router to perform routing on the LAN
side and bridging on the WAN side. MER is needed only when your Network Service
Provider doesn’t support IP routing. MER adds NAT functionality, thereby providing
greater security and more IP addresses for your LAN than what is provided by your
NSP.
Why can’t I get a response after entering a URL in my browser?
If you do not get a response, try pinging the IP address. If you get a response to pinging, then your Domain Name Service (DNS) is probably failing. You should contact
your NSP for DNS assistance. If you do not get a response, then try pinging the WAN
Gateway address (of your NSP) to confirm that your router can connect with the NSP.
If pinging fails, check the router’s lights. The WAN lights on the router front should be
green. Also check your cable connections. If everything appears correct, check your IP
configuration and ensure that the gateway and LAN IP addresses match.
How can I connect my modem for dial backup if the connector on my dialup
modem doesn’t match the console port on the router?
You need the Dial Backup Cable Kit (part number 120-0501-001), available from the
Efficient Networks web site at the following address: http://www.efficient.com
My modem is not a V.90. Can I use it for dial backup?
Yes, you can use a non-V.90 modem with your router for dial backup. Be sure to use
the correct initialization string for your modem (consult your modem documentation).
Page 3-2
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 4: Product Specifications
CHAPTER 4
CHAPTER 4
PRODUCT SPECIFICATIONS
Front Panel
Figure 4-1: 5930 Business Gateway Front Panel
Table 4-1: Front Panel Light Indications
Light
Power
Color
Green
Off
Test
Yellow:
Yellow flashing:
Green: (2 sec blink)
Off:
WAN
LAN
Efficient Networks®
Yellow:
Yellow flashing:
Indications
Power is ON
Power is OFF
Running Power On Self Test
Self Test Failure
Self Test successful (heartbeat)
Router is shut down
Green:
Off:
Establishing DSL modem link
Establishing DSL throughput
DSL modem link successful
DSL modem link is shut down
Green flashing:
Green:
Off:
Data traffic detected
LAN stauts - OK
LAN status - Not OK
Page 4-1
Chapter 4: Product Specifications
Efficient Networks® 5930 Business Gateway
User Reference Guide
5930 Back Panel
BKUP
Figure 4-2: 5930 Router Back Panel
Table 4-2: 5930 Back Panel Port Functions
Connection
Function
Power
Uses a 12V DC/AC power adapter.
Ethernet Ports
Eight Ethernet T-100 switch ports (8-pin, RJ-45)
Management
Port
This 8-pin, RJ-45 port provides RS232 connectivity
for console connections or a dial backup analog (extrenal) modem connection.
Backup
A 6-pin RJ-11 port connects the internal modem.
DSL/WAN
Port
A 6-pin RJ-11 connects the DSL.
Hardware Specifications
Physical Specifications
•
Dimensions:11.75W x 6D x 2.25H inches
•
29.8W x 15.2D x 5.7H cm
•
Weight:1.5 lbs.
•
.68 Kg.
Operational Environment
Page 4-2
•
Temperature:40°F to 105°F
•
5°C to 40°C
•
Humidity:20% to 80% non-condensing
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 4: Product Specifications
Power Requirements
•
AC Voltage:100 to 120V AC or 220 to 240V AC
•
Frequency:50/60 Hz
•
Consumption:10W maximum
Processor
•
Motorola® MPC855T
•
8 MB DRAM, 4 MB Flash Memory
•
Motorola® MPC180 Encryption Processor
LAN Interface
•
Built-in eight port Ethernet switch with RJ-45 connectors
•
Green/Amber LEDs
•
LAN speed of 10 or 100 Mbps, full or half duplex, with auto-sense switch
WAN Interface
•
One Digital Subscriber Line interface as follows:
•
ADSL, Annex A
•
RJ-11 with 2-3 pinout (center pair)
Serial Interface
•
One RS-232 asynchronous console or external modem port (RJ-45)
Agency Approvals
•
CE Mark
•
TUV
•
Safety:UL 1950, CSA 22.2, EN 60950
•
Emissions:FCC Part 15 Class B, EN55022
•
Immunity:EN50082-1, EN55024
Efficient Networks®
Page 4-3
Chapter 4: Product Specifications
Efficient Networks® 5930 Business Gateway
User Reference Guide
Software Specifications
Bridging
•
Transparent bridging including Spanning Tree protocol (IEEE 802.1D)
•
Bridge filters
Routing
•
TCP/IP with RIP1 (RFC 1058), RIP1 compatible and RIP2 (RFC 1389) or
static routing on the LAN or WAN
•
Novell IPX with RIP/SAP (RFC 1552)
•
DHCP client (RFC 2132)
•
DHCP server - Automatic assignment of IP address, mask, default gateway
and DNS server addresses to workstations (RFC 2131, 2132)
•
DHCP relay agent (RFC 1542)
•
DNS relay
•
Multiple subnets on LAN
•
Virtual routing
•
Virtual Router Redundancy Protocol (RFC 2338)
®
Configuration Management
•
Easy Setup Web Management Interface
•
Microsoft® Windows configuration management via SNMP
•
TFTP download/upload of new software and configuration files
•
Performance monitor
•
Dynamic event and history logging
•
Administration through HTTP, SNMP, Telnet or VT100 terminal
•
Network boot uses the BootP server (RFC 2131, RFC 2132)
Differentiated Services - Quality of Service provisioning
Page 4-4
•
Weighted Fair Queuing (WFQ)
•
Differentiated Services (DiffServ)
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Chapter 4: Product Specifications
Dial Backup
•
Internal V.90 modem1
•
Failover to external V.90 or ISDN modem via console port
•
Web graphical user interface
•
User selectable fail/restore criteria
•
Optional modem connector (DB9 or DB25)
•
Supports L2TP and IPSec tunnel failover
Asynchronous Transfer Mode (ATM)
•
Encapsulation (IP, Bridging, and Bridge Encapsulated Routing) (RFC 1483)
•
PPP over ATM (LLC and VC multiplexing) (RFC 2364)
•
PPP over Ethernet
•
Classical IP (RFC 1577)
•
AAL5 for data
•
Multiple Virtual Circuits (VCs)
•
Virtual Circuit (VC) traffic shaping (UBR, VBR, CBR)
•
L610 OAM F5 loopback
IP Address Translation
•
Network renumbering (RFC 1631)
•
Network Address Translation (NAT/PAT)
•
LAN servers supported with NAT
•
Support for NAT inside an IPSec tunnel
Protocol Conformance Testing
•
RFC 1483 (Bay Networks™, Cabletron™, Cisco™, RedBack™)
•
PPP over ATM (Cisco, Escalate™, RedBack) (RFC 2364)
PPP (RFC 1661)
•
Data compression of up to 4:1 (STAC™ LZS) (RFC 1974)
•
Van Jacobsen header compression (RFC 1144)
•
Spoofing and filtering (IP-RIP, IPX-RIP, SAP, Watchdog, serialization)
•
Automatic IP and DNS assignment (RFC 1877)
•
PPP over Ethernet (RFC 2516)
Efficient Networks®
Page 4-5
Chapter 4: Product Specifications
Efficient Networks® 5930 Business Gateway
User Reference Guide
Security
•
Role-based management
•
User authentication (PAP/CHAP) with PPP (RFC 1334, RFC 1994)
•
Password control for Configuration Manager
•
SNMP password and community name reassignment
•
HTTP/Syslog/SNMP/Telnet port reassignment, access control list
•
VPN support (L2TP, IPSec, IKE, DES, 3DES)
•
Firewall (IP filtering)
•
Stateful Firewall (ICSA Compliant)1
•
Secure Management Communications – IPsec and SSH
•
Radius Server support
•
Optional VPN Hardware Acceleration support 1
1 Key-Enabled
Page 4-6
feature
Efficient Networks®
Efficient Networks® 5930 Business Gateway
User Reference Guide
Appendix A
APPENDIX A
Support
Appendix0
For specific product support, contact the organization that provided or sold the
equipment to you. If you need to contact your Network Service Provider for technical
support, please have the following information ready:
•
Router model number (on the bottom of the unit)
•
Router software version. If you are unsure about your router’s software
version, it can be identified by one of the following methods:
–
To display on the command line, enter: ver
–
To display via the Web Management Interface, go to the Router
Information Page (click Home)
•
Web User Interface
•
Date of purchase
•
OS Type (e.g. Windows 95, 98, 2000, NT, MacOS, or Unix)
•
A detailed description of the problem
End of Document
Efficient Networks®
Page A-1
Appendix A
Efficient Networks® 5930 Business Gateway
User Reference Guide
This page intentionally left blank.
Page A-2
Efficient Networks®