advertisement
CCVSR Video Session Recorder
User Manual
www.aten.com
ii
CCVSR User Manual
FCC Information
This is an FCC Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
RoHS
This product is RoHS compliant.
SJ/T 11364-2006
The following contains information that relates to China.
CCVSR User Manual
User Information
Online Registration
Be sure to register your product at our online support center:
International
North America http://support.aten.com
http://www.aten-usa.com/product_registration
Telephone Support
For telephone support, call this number:
International
China
Japan
Korea
North America
United Kingdom
886-2-8692-6959
86-10-5255-0110
81-3-5615-5811
82-2-467-6789
1-888-999-ATEN ext 4988
44-8-4481-58923
User Notice
All information, documentation, and specifications contained in this manual are subject to change without prior notification by the manufacturer. The manufacturer makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties as to merchantability or fitness for any particular purpose. Any of the manufacturer's software described in this manual is sold or licensed as is.
Should the programs prove defective following their purchase, the buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from any defect in the software.
The manufacturer of this system is not responsible for any radio and/or TV interference caused by unauthorized modifications to this device. It is the responsibility of the user to correct such interference.
The manufacturer is not responsible for any damage incurred in the operation of this system if the correct operational voltage setting was not selected prior to operation. PLEASE VERIFY THAT THE VOLTAGE SETTING IS
CORRECT BEFORE USE.
iii
CCVSR User Manual
Package Contents
Basic Package
The Video Session Recorder package consists of:
1 Video Session Recorder USB License Key
1 Software CD
1 User Instructions*
Check to make sure that all of the components are present and in good order.
If anything is missing, or was damaged in shipping, contact your dealer.
Read this manual thoroughly and follow the installation and operation procedures carefully to prevent any damage to the switch or to any other devices on the Video Log Server installation.
* Features may have been added to the Video Log Server since this manual was published. Please visit our website to download the most up-to-date version.
Copyright © 2013 ATEN® International Co., Ltd.
F/W Version: V1.0.062
Manual Date: 2013-05-28
Altusen and the Altusen logo are registered trademarks of ATEN International Co., Ltd. All rights reserved. All other brand names and trademarks are the registered property of their respective owners.
iv
CCVSR User Manual
Contents
Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Introduction
KVM Over the NET™ Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Secondary Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Add Node Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
VSR Installation
VSR Application
Server Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
v
CCVSR User Manual
Service Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Archive Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Disable Keystroke Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Upgrading the License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
VSR Archive Server
Installing the VSR Archive Server. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Starting the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Begin Time/End Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Search Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Play Selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Begin Time/End Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Device Name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Search File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Export File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Export & Delete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Delete File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Import File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
The User Interface
The Web Browser Main Page. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Page Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Playback
vi
CCVSR User Manual
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
User Management
Modifying User Accounts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Deleting User Accounts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Creating Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Modifying Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Deleting Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Assigning Users to a Group From the User’s Notebook . . . . . . . . . . . 50
Removing Users From a Group From the User’s Notebook . . . . . . . . 51
Assigning Users to a Group From the Group’s Notebook . . . . . . . . . . 52
Removing Users From a Group From the Group’s Notebook . . . . . . . 53
Assigning Device Permissions From the User’s Notebook . . . . . . . . . 54
Assigning Device Permissions From the Group’s Notebook . . . . . . . . 55
Assigning System Permissions From the User’s Notebook . . . . . . . . 56
Assigning System Permissions From the Group’s Notebook . . . . . . . 57
Device Management
Recording KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Adding KVM Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Configuring KVM Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Deleting KVM Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Logs
vii
CCVSR User Manual
System Management
Event Destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Login Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Account Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Private Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Certificate Signing Request. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Video Session Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Adding Secondary VSR Servers . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Deleting Secondary VSR Servers . . . . . . . . . . . . . . . . . . . . . . . . . 82
Enable/Disable Secondary VSR Servers . . . . . . . . . . . . . . . . . . . 82
Maximum Recording Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Preferences
Appendix
USB Authentication Key Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Supported KVM Over the NET™ Switches . . . . . . . . . . . . . . . . . . . . . . . 89
Self-Signed Private Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
viii
CCVSR User Manual
About This Manual
This User Manual is provided to help you get the most from your Video Log
Server system. It covers all aspects of installation, configuration and operation.
An overview of the information found in the manual is provided below.
Chapter 1, Introduction, introduces you to the Video Session Recorder
application. Its purpose, features, benefits, and requirements are presented.
Chapter 2, VSR Installation, provides step-by-step instructions for
installing the Video Session Recorder software.
Chapter 3, VSR Application, describes how to use the VLog application,
and explains it’s features and function.
Chapter 4, VSR Archive Server, describes how to use the VSR Archive
Server, and explains it’s features and function.
Chapter 5, The User Interface, explains how to login to the Video Session
Recorder using a web browser.
Chapter 6, Playback, explains how to use the features and functions of the
Playback page, used to search and play video log files.
Chapter 7, User Management, shows super administrators and
administrators how to create, modify, and delete users and groups, and assign attributes to them.
Chapter 8, Device Management, shows super administrators how to add
KVM devices and configure ports on the Video Session Recorder, in order to record video logs.
Chapter 9, Logs, shows how to use the log file utilities to view the events
that take place on the Video Session Recorder.
Chapter 10, System Management, explains how to use the System
Management page to configure System Information, Network, ANMS, Security, and the Video Session Recorder settings.
Chapter 11, Preferences, explains how to set custom preferences for the
user currently logged in.
An Appendix, at the end of the manual provides technical and troubleshooting information.
ix
x
CCVSR User Manual
Conventions
This manual uses the following conventions:
Monospaced
[ ]
1.
♦
→
Indicates text that you should key in.
Indicates keys you should press. For example, [Enter] means to press the Enter key. If keys need to be chorded, they appear together in the same bracket with a plus sign between them:
[Ctrl+Alt].
Numbered lists represent procedures with sequential steps.
Bullet lists provide information, but do not involve sequential steps.
Indicates selecting the option (on a menu or dialog box, for example), that comes next. For example, Start
→
Run means to open the Start menu, and then select Run.
Indicates critical information.
Product Information
For information about all ALTUSEN products and how they can help you connect without limits, visit ALTUSEN on the Web or contact an ALTUSEN
Authorized Reseller. Visit ALTUSEN on the Web for a list of locations and telephone numbers:
International
North America http://www.aten.com
http://www.aten-usa.com
Chapter 1
Introduction
Overview
The Video Session Recorder is ATEN’s innovative software which was developed to work with ALTUSEN KVM Over the NET™ products to securely and reliably record the video and operation of computers which are connected through KVM ports. Not only does the software record a video of the screen display but also logs operations such as key-strokes and mouse clicks. The software can be managed to record specific server ports automatically for convenient auditing and safe management.
The Video Session Recorder supports the recording of multiple KVM Over the
NET™ switches, and up to 12 active KVM ports can be recorded at the same time. With the specialized video player tool, encrypted file formats, and user permission settings; only authorized users can view, search, and delete recorded videos and operational logs, ensuring the highest level of security with customized management for automated functionality.
Furthermore, the Video Session Recorder offers powerful search capabilities; the recorded videos and operation logs can be searched by time, device, or port.
When playing searched recordings, in addition to the video image, the screen also shows the operations (mouse clicks and key-strokes) being made by the user logged into the computer, arranged in order of recorded time, for easy monitoring, and boosting the efficiency of detailed management and auditing.
The Video Session Recorder is a great tool to create reference and instructional type videos. For instance, if a complex update is required across field office servers, administrators can quickly generate a step by step instructional video with the exact key-strokes and mouse clicks shown on the screen. The administrator can then send the video to branch offices for implementation, instantly reducing training and support time. Videos can be created for software and network training or implementation; installations, configurations and system updates or any computer related instructions. Another advantage is that videos are created and saved automatically when the KVM port is accessed, and are password protected for security.
By integrating the Video Session Recorder into your KVM installation, you can automate the security of your server room and make auditing an effective tool.
1
CCVSR User Manual
Features
Automatically create complete recordings of a computer’s operations when remote users access a KVM port – which are saved to an indexed database for advanced searches
Supports high quality video recordings – with a video resolution up to
1600 x 1200 with 16 bit color depth
Supports recording on multiple KVM Over the NET™ Switches
Simultaneously records and plays the operation of multiple KVM ports*
Search functions with keyword filters for video recordings
Special video player tools with format, video record exporting, and password protection for enhanced security
IP Filter for enhanced protection
System event notification via SMTP email; SNMP trap and Syslog support
Configurable user and group permissions – for search, play, system management, record management, and save management
Port level permissions – users can only view ports they have been authorized on
Supports device level event logs
Archive Server Support
Multilanguage GUI Supports: English, Traditional Chinese, Simplified
Chinese, Japanese, and Korean
Automatically runs software as daemon service in the background
Multi-browser support: Internet Explorer, Chrome, Firefox, Safari, Opera,
Mozilla, Netscape
Supports SSL 128-bit data encryption and RSA 1024-bit certificates for secure web browser logins
3rd party remote authentication supports: RADIUS, LDAP, LDAPS, and
MS AD Directory
*Up to 12 KVM sessions can be recorded at one time when the recommend hardware requirements of the CCVSR server are met.
2
Chapter 1. Introduction
Requirements
Computer
Systems that the Video Session Recorder will be installed on should meet the following requirements:
Hardware Requirements
Minimum/4 video sessions: Intel® Pentium 4, 2.6GHz, 2G RAM
Maximum/12 video sessions: Intel® Intel Core™ i5, 2.5GHz, 4G
RAM
Hard drive: 500MB or more free space
Ethernet: At least 1 Ethernet adapter (100Mbps or higher) – Giga LAN recommended
Operating System Requirements:
Windows: XP, 7, 2003, 2008
KVM Over the NET™ Switch
Computers recorded by the Video Session Recorder must be connected to a
port on a KVM Over the NET™ Switch (see Supported KVM Over the NET™
Browsers
Supported browsers for users that log into the Video Session Recorder include the following:
Browser
Chrome
IE
Firefox
Mozilla
Netscape
Opera
Safari
Version
20.0.1 and higher
6 and higher
1.5 and higher
1.7 and higher
8.1 and higher
11.64 and higher
6.0 and higher
3
CCVSR User Manual
Licenses
The CCVSR license controls the number of Primary Servers, Secondary
Servers, Archive Servers and nodes permitted on the CCVSR installation.
License information is contained on the USB License Key that came with your
CCVSR purchase. For a sample deployment see CCVSR Deployment
Example:, page 5, for details.
Upon completion of the CCVSR software installation, the number of licenses that you purchased is automatically added. To add anything more, you must upgrade the license. See Upgrading the License, page 172, for detailed information.
Primary Servers
Management - A Primary Server is the central management software used to record, view, and manage all aspects of a CCVSR installation. All Secondary
Servers, Archive Servers, and Nodes work through the Primary Server.
Secondary Servers
Storage - Secondary Servers reduce the work load and provide extended storage for the Primary Server - with limited configuration functionality.
Archive Servers
Archive - The Archive Server automatically archives all video log files created on the Primary Server into a separate organized database for extended backup and viewing. The Archive Server allow you to import, export, and allocate large databases separate from the VSR system.
Nodes
KVM Ports - A node is a physical port on a KVM Over the NET™ Switch.
Each node you want to record video logs on requires a license.
4
CCVSR Deployment Example:
256 Nodes
KVM Over the Net Switches
Chapter 1. Introduction
Secondary
Primary
Archive
License Options
Model
CCVSR8
CCVSR16
CCVSR32
CCVSR64
CCVSR128
CCVSR256
CCVSR512
CCVSR1024
CCVSR2048
CCVSRUnlimited
Node
8
16
32
64
128
256
512
1024
2048
Unlimited
Primary
1
1
1
1
1
1
1
1
1
1
Secondary
Secondary
5
CCVSR User Manual
Add Node Options
Add License Model
CCVSRN1
CCVSRN8
CCVSRN16
CCVSRN32
CCVSRN64
CCVSRN128
CCVSRN256
CCVSRN512
CCVSRN1024
CCVSRN2048
Nodes
1
8
16
32
64
128
256
512
1024
2048
6
Chapter 2
VSR Installation
Overview
This chapter describes how to install the Video Session Recorder (VSR) software on a computer. The VSR application runs background services for the
Video Session Recorder to operate and is used to set basic server configurations. The VSR application must be running for the Video Session
Recorder’s web browser features to work.
Installing the VSR Software
Starting the Installation
To install the VSR application on a Windows system, do the following:
If you are installing on a computer running Windows XP, you must
first install IPv6. See Windows XP Installation, page 90, for details.
1. Put the software CD that came with your package into the computer’s CD drive.
2. Go to the folder where the setup.exe file is located, and execute it. A screen, similar to the one below, appears:
Click Next to continue.
7
CCVSR User Manual
3. On the Select Installation Folder page, specify the installation folder, or click Browse to choose the location where you want to install it. Then choose if you want to install it for yourself (Just me), or for anyone who uses this computer (Everyone). Click Disk Cost to view available drives and disk space.
Click Next to continue.
4. The Confirm Installation window appears, click Next to continue:
8
Chapter 2. VSR Installation
5. When the installation is complete the following message will appear:
Licenses
Upon completion of the VSR software installation, a default license for one server is automatically provided. To add more Video Session Recorders, you
must upgrade the license. To upgrade the license, See License, page 18, for
details. For License options See License Options, page 5, for details.
9
Chapter 3
VSR Application
Overview
The Video Session Recorder (VSR) application runs background services for the Video Session Recorder’s browser interface to operate and allows you to view logs, set basic server configurations, and run backup/restore maintenance tasks. The VSR application starts the services that run the Video Session
Recorder, and allow the management functions within a web browser session
(see Chapter 5, The User Interface). This chapter describes the VSR
application’s features.
VSR Login
To start VSR and login to the application, do the follow:
1. Double click the VSR shortcut from the Start Menu or desktop:
A VSR icon like the one above will appear in the taskbar, after step 2 is complete.
2. The first time you open the VSR application the Config Server Type screen
appears (see Server Type, page 15, for details), set the type and click OK.
10
Chapter 3. VSR Application
3. The Config dialog box appears with two VSR Service options, as shown:
Register VSR Service: This option installs and registers the VSR
Service with the Windows operating system so that it can run the software in the background.
Start VSR Service: This option will start the VSR Service automatically after the installation is complete.
4. Next, click the VSR icon from the taskbar. When the authentication screen appears on the monitor, enter the username and password:
Since this is the first time you are logging in, use the default Username:
administrator; and the default Password: password. Click OK.
11
CCVSR User Manual
5. Once you are logged in, the main page appears:
12
Chapter 3. VSR Application
The VSR Main Page
When the VSR application opens you have 5 tabs to choose from: Sessions,
System Log, Settings, Maintenance, and License. From each tab you can Exit to logout and shut down the VSR application- stopping all Video Session
Recorder services, or Hide to logout and continue running the VSR application while minimized to the task bar. Anytime you need to Save your settings, VSR will automatically shutdown to allow the changes to take affect, and you will need to restart the application.
Sessions
The Session tab lets you see at a glance which users are currently logged into the main Video Session Recorder’s browser interface, and provides information about each session.
The meanings of the column headings are fairly straightforward. The IP heading refers to the IP address that the user has logged in from, the Login Time shows when the user logged in to the Video Session Recorder, and the
Category displays the type of user that logged in.
This page also gives the administrator the option of forcing a user logout by selecting the user and clicking End Session at the bottom of the page.
13
CCVSR User Manual
System Log
The System Log tab provides a detailed log of events taking place on the Video
Session Recorder.
The System Log provides a breakdown of time, user, and a description of each event occurring. The log file tracks a maximum of 512 events. When the limit is reached, the oldest events get discarded as new events come in.
You can clean all System logs by clicking Clear.
14
Chapter 3. VSR Application
Settings
The settings tab is used to determine how the Video Session Recorder functions on the local machine: as a Primary Server or Secondary Server, and has two sections.
Server Type
Primary Server
Select Primary Server for a computer that is running as the main Video Session
Recorder. This computer will host and manage all aspects of the Video Session
Recorder, and can add computers running as Secondary Servers for extended storage of video log files.
Secondary Server
Select Secondary Server if the computer is being used as storage space for video log files from a Primary Server. As a Secondary Server, it’s only function will be to store video log files for the Primary Server, and when you login to the VSR application only the Settings tab is available. If you choose this option, provide the following information:
Primary Address- input the IP address of a computer running as the
Primary Video Session Recorder.
Service Port: input the Program Service Port number of the Primary
Server. The default service port for this feature is 9002.
The Secondary Server must be added to the Primary Server in order to work.
See Video Session Recorder, page 81, for details.
15
CCVSR User Manual
Service Ports
As a security measure, if a firewall is being used, the Administrator can specify the port numbers that the firewall will allow. If a port other than the default is used, users must specify the port number as part of the IP address when they log in. If an invalid port number (or no port number) is specified, the Video
Session Recorder will not be found. An explanation of the fields is given in the table below:
Program
HTTP
HTTPS
Field Explanation
This is the port number to configure on a Secondary
Server to connect to a Primary Server hosting the Video
Session Recorder (see page 15 for details).
The default is 9002.
The port number for a browser login.
The default is 9080.
The port number for a secure browser login.
The default is 9443.
For Example: To access a Video Session Recorder with an IP address of
192.168.0.100, using a secure browser login (https), enter: https://192.168.0.100:9443
Note: 1. Valid entries for all of the Service Ports are from 1–65535.
2. Service ports cannot have the same value. You must set a different value for each one.
3. If there is no firewall (on an Intranet, for example), it doesn’t matter what these numbers are set to, since they have no effect.
Archive Server
If you have installed a VSR Archive Server, input the IP Address and Port number of the computer hosting the software. For more information on
configuring the Archive Server see VSR Archive Server, page 19, for details.
Disable Keystroke Recording
If you put a check in this box the Video Session Recorder will not record the keystrokes that occur on a computer during video sessions that are recorded
16
Chapter 3. VSR Application
Maintenance
The Maintenance tab is used to Backup and Restore system configuration settings and user account information to/from a file or system created
Checkpoint. There are two sections:
Backup
To create a backup file, enter a password, then click Backup to save the file.
Leave the Password field blank if you don’t want to use a password. The saved data file contains the current system configuration and all user account information.
Restore
To restore data, click Choose to select a Filename or Checkpoint to restore a system created Checkpoint. Enter the Password if restoring from a file, and click Restore.
If using Filename to restore data, choose the type of data you want to restore:
Select All: Restores all data from the backup file.
User Account: Restores only user account related data from the backup file.
User Select: Restores only the data (User Account, Network, Security, Device
Management, ANMS, and Video Session Recorder) you select to recover.
17
CCVSR User Manual
License
The License tab is used to upgrade your software and add server licenses.
Upgrading the License
The license controls the total number of Nodes purchased and Available
Nodes not in use; permitted with your Video Session Recorder installation.
The license information is contained on the USB License Key that came with your purchase.
Upon completion of the VSR software installation, a default license for one primary server is automatically provided. To add more Video Session Recorder nodes, you must upgrade the license.
To upgrade the license:
1. Use the USB key that came with your package or contact your dealer to obtain a new license key for the number of primary and/or secondary servers you want to add.
2. Insert the license key into a USB port on your Video Session Recorder.
3. Login to the VSR application, and from the License tab click Upgrade.
You can now install and use additional Video Session Recorders (per the number of licenses purchased), which will communicate and work in conjunction over a network.
Note: 1. Once the upgrade has completed, it is no longer necessary to keep the key plugged into the USB port. Remove the key and place it somewhere safe, since you will need it for future upgrades.
2. If you lose the USB license key, contact your dealer to obtain another one. If you supply the key’s serial number the new key will contain all of the information that was stored on the lost key.
18
Chapter 4
VSR Archive Server
Overview
The VSR Archive Server allows you to store, playback, import, and export data created on VSR servers. The software automatically transfers a copy of the video log files from the Primary VSR server into an organized archive separate from the main system. This gives you the ability to purge older files from the main system but keep a safe archive of all videos for future use. The Archive
Server runs in the background and updates the archive automatically every 15
minutes. To purchase this software, please see Licenses, page 4, for details.
Installing the VSR Archive Server
Starting the Installation
To install the Archive Server on a Windows system, insert the USB License
Key into your computer, and do the following:
1. Put the software CD that came with your package into the computer’s CD drive, or open the folder with the installation file.
2. Go to the folder where the setup.exe is located and double click it. A screen similar, to the one below, appears:
Click Next to continue.
19
CCVSR User Manual
3. On the Select Installation Folder page, specify the installation folder, or click Browse to choose the location where you want to install it. Then choose if you want to install it for yourself (Just me), or for anyone who uses this computer (Everyone). Click Disk Cost to view available drives and disk space.
Click Next to continue.
4. The Confirm Installation window appears, click Next to continue:
20
Chapter 4. VSR Archive Server
5. If a message appears to insert the License Key, re-plug the USB License
Key into your computer or try a different USB port, then click Retry.
Clicking Ignore will install the software but you will not be able to use it until the USB License Key has been made available.
6. The Config dialog box appears, select the options and click OK:
Register VSR Service: This option registers the VSR Service with the
Windows operating system so that it can run the software in the background.
Start VSR Service: This option will start the VSR Service automatically after the installation is complete. It is recommend to select both options.
21
CCVSR User Manual
7. When the installation is complete the following message will appear:
Licenses
Upon completion of the VSR software installation, a default license for one server is automatically provided. To add more Video Session Recorders, you
must upgrade the license. To upgrade the license, See License, page 18, for
details. For License options See License Options, page 5, for details.
22
Chapter 4. VSR Archive Server
Archive Server GUI
The Archive Server’s interface has 5 tabs: Playback, Export/Import, Storage,
Settings, and License; all described below. Once the software has been installed, double click the Archive GUI icon located on the desktop, and the
Playback page appears:
Use the Exit button to shutdown the Archive Server, or Hide button to minimize the window to the task bar.
Setup
There are two steps to setup the Archive Server- set the Archive Server’s IP address on the Primary VSR server, and add a storage location from the
Archive Server’s Storage tab.
First, configure the Archive Server’s IP Address on the Primary VSR Server
(see Archive Server, page 16). Next, add a storage location from the Storage
tab (see Storage, page 28). The storage location is where the archived video log
files are saved.
After the IP address is configured and a storage location is added, the Archive
Server will begin to automatically archive all video log files created after the installation. The archive is updated every 15 minutes. To check for new video log files, go to the Playback tab and click Search. All new video log files will appear in the search window.
23
CCVSR User Manual
Playback
The Playback tab is used to search and playback video log files which have been archived or manually imported. To see a list of all video log files that have been archived, simply click the Search button.
The Playback tab has 3 sections used to search and playback archived video log files.
Begin Time/End Time
This section allows you to filter the search results by the begin and end time.
The Begin Time and End Time refers to the time when the actual video log recording took place on the KVM switch.
Search Filter
The Search Filter is used to search for archived video log files by the Port
Name, Device Name, or Port Number of the KVM switch they were recorded on. After inputting the search data, click Search. Your search results* will appear at the bottom of the page, and you can sort your results using the columns provided. If you would like to view all archived video logs, simply leave the fields blank and click Search.
24
Chapter 4. VSR Archive Server
Play Selected
To playback video logs, click Search* for a list of the archived video log to appear:
Select the checkboxes of the video(s) you want to playback, then click Play
Selected. The video will open in a new window with the Video Log Viewer
application. For information on the Video Log Viewer, see Video Log Viewer, page 39.
Note: 1. If no video log files appear after clicking Search, either the archive hasn’t updated, in which case you should wait 15 minutes; or a
storage location needs to be added on the Storage tab (see Storage, page 28).
2. Only video logs created after the Archive Server was installed are automatically archived from the Primary VSR server. Video logs created before the installation must be manually imported from the
Export/Import tab (see Export/Import, page 26).
25
CCVSR User Manual
Export/Import
The Export/Import tab is used to export and import video log files in a single database (.vse) file format. The database (.vse) files can combine a large number of individual video logs into a single compressed file to reduce disk space, which can be exported for storage and imported for use. The Export/
Import tab also allows you to import individual video log files (.dat) created on the VSR Primary Server.
You can search for files to export (which are already archived) by selecting a
Device Name and clicking Search File; or manually import .vse or .dat files into the Archive Server by clicking Import File. For more information on imported files see Import File below.
Begin Time/End Time
This section allows you to filter the search results by the begin and end time.
The Begin Time and End Time refers to the time when the actual video recording took place on the KVM switch.
Device Name
This section lists the name(s) of the KVM switches which have been added to the Primary VSR server. You can select a device(s) and click Search for a list of individual video log files which have been archived from that KVM switch.
After doing so you can select video logs to export into a .vse database file.
26
Chapter 4. VSR Archive Server
Search File
The Search File button is used to search for video log files on the Device Name you have selected. The results will appear in the lower section of the window, as shown below. After doing so you can select video logs to export into a .vse database file.
Export File
When you export logs they are saved in a single compressed .vse database file.
Select the video log file(s) displayed in the lower window that you want to export, click Export File and provide a name to save the .vse file as.
Export & Delete
The Export & Delete button exports the selected files into a .vse database file and deletes the individual video log files that you are exporting from the
Archive Server. This is a fast way to purge the individual files you are archiving into a single database.
Delete File
The Delete File button deletes the selected video log file from the Archive
Server.
Import File
The Import File button is used to import database files (.vse) and individual video log files for viewing, archiving, or creating a new database- for export.
Click Import File, to browse and select the (.dat or .vse) file(s) to import, click
Open. If you open a .vse database file: select the files from the list and click
Import. Importing files will copy them into the Archive Server, therefore before you can import files, a storage location needs to be added from the
Storage tab (see Storage, page 28). The storage location is where the archived
files are saved, by the date they were created.
27
CCVSR User Manual
Storage
The Storage tab is used to add storage locations. This is where archived video logs are saved. You can add multiple storage locations for video logs. When the first location becomes full, the second will be used, and so on. Video logs are archived into folders according to the date they were created. The Archive
Server cannot archive video logs until a storage location is added and enabled.
To add and enable a storage location, do the following:
1. Click Add, and the following window appears:
2. Type in the Path or click Browse to select a storage location.
3. In the Pre-Allocate Space(GB) field enter the maximum amount of disk space to use, then click Save. The storage location appears in the lower window.
4. Next, check the Enable Use box and click Save.
Select a Storage Location and click Modify to modify it, or Remove to remove it. Click Save to save the changes.
28
Settings
The Settings tab is used to set the Server Settings:
Chapter 4. VSR Archive Server
On this tab you can set the Service Port and Language. The default Service Port is 9006.
29
CCVSR User Manual
License
Use the License tab to upgrade your license key. Insert the USB License Key into your computer, then click Upgrade.
If the upgrade fails, re-insert the USB License Key, or try a different USB port on your computer.
30
Chapter 5
The User Interface
Overview
The Video Session Recorder’s user interface is accessed via web browser and contains the main features and functions. This chapter explains how to login to the Video Session Recorder and highlights the browser components.
Browser Login
The Video Session Recorder is accessed via an Internet browser running on any platform. To access the Video Session Recorder’s browser interface, the VSR
application must be started (See VSR Application, page 10, for details).
To access the Video Session Recorder, do the following:
1. Open the browser and specify the IP address and service port of the Video
Session Recorder you want to access in the browser's location bar.
For example: https:\\192.168.0.100:9443
2. When a Security Alert dialog box appears, accept the certificate – it can be
trusted. If a second certificate appears, accept it as well (see Trusted
Once you accept the certificate(s), the login page appears:
3. Provide your username and password, then click Login to bring up the
Web Main Page.
Note: Since this is the first time you are logging in, use the default Username:
administrator; and the default Password: password.
31
CCVSR User Manual
The Web Browser Main Page
Once users login and are authenticated, the Web Browser Main Page comes up, with the Playback page displayed:
Note: The screen depicts a Super Administrator’s page. Depending on a user’s type and permissions, not all of these elements appear.
Page Components
The web page screen components are described in the table, below:
No.
1 Tab Bar
Item
2 Menu Bar
Description
The tab bar contains the Video Session Recorder’s main operation categories. The items that appear in the tab bar are determined by the user’s type, and the authorization options that were selected when the user’s account was created.
The menu bar contains operational sub-categories that pertain to the item selected in the tab bar. The items that appear in the menu bar are determined by the user’s type, and the authorization options that were selected when the user’s account was created.
32
Chapter 5. The User Interface
No.
3 Sidebar
Item Description
The Sidebar provides a tree view listing of components that relate to the various tab bar and menu bar selections. Clicking a component in the Sidebar brings up a page with the details that are relevant to it.
Note: Some tabs don’t have a sidebar as it’s functions don’t require one.
4
5
About
Logout
About provides information regarding the switch’s current firmware version.
Click this button to log out of your Video Session
Recorder’s session.
6 Welcome Message If this function is enabled a welcome message displays here.
7 Interactive Display
Panel
This is your main work area. The screens that appears reflects your menu choices and Sidebar node selection.
The Tab Bar
The number and type of icons that appear on the Tab Bar at the top of the page are determined by the user’s type (Super Administrator, Administrator, User) and the permissions assigned when the user’s account was created. The functions associated with each of the icons are explained in the table below:
Icon Function
Playback: The Playback page is used to search and playback available video logs, and to monitor current browser sessions.
Playback is discussed on page 35.
User Management: The User Management page is used to create and manage Users and Groups. It can also be used to assign devices to them. This tab is available to the Super Administrator, as well as administrators and users who have been given User Management permission. The tab doesn’t appear for other administrators and users.
User Management is discussed on page 42
Device Management: The Device Management page is used to add
KVM devices and configure the ports for recording video logs. This page is available to the Super Administrator, as well as administrators and users who have been given Device Management permission. The tab doesn’t appear for other administrators and users. The Device
Management is discussed on page 58.
System Management: The Systems Management page is used to configure the Video Session Recorder’s system settings and to add secondary servers from the network. System Management is
33
CCVSR User Manual
Icon Function
Logs: The Log page displays the contents of the log file. The Log page
Preferences: The Preference page is used to customize the user’s preferences for the user that is currently logged in. The Preferences
There are two small icons at the extreme right of the page. Their functions are described in the table, below:
Icon Function
Click this icon to bring up a panel with information about the Video
Session Recorder firmware version.
Click this icon to log out and end your Video Session Recorder session.
34
Chapter 6
Playback
Overview
The Playback tab is used to search and playback video log files and manage user sessions. The Playback tab has 3 menu pages; Search Video, Advanced
Search, and Sessions, as described below. Before using the Playback tab, you
must first add a KVM device, see Recording KVM Ports, page 58 for details.
Search Video
When you login to the Video Session Recorder the Playback tab comes up with the Search Video page displayed. The Search Video page is used to find video logs by device, port, or time.
The Search Video page is organized into several main areas. The Port List section shows all the KVM devices and ports that a user is permitted to access.
The Filter section is used to filter the Port List to find videos within the chosen variables.
35
CCVSR User Manual
Port List
The Port List is used to find video logs by port. Ports list under the KVM device they are attached to. When you select a port with a video log, a section appears below it, listing all the video captured from that port, as shown here:
Playback
To playback a video log, select it from the Search Results, then click Play
Selected, or Play All. The video will open in a new window with the Video Log
Viewer application. For information on the Video Log Viewer, see Video Log
Filter
Use the Filter section to condense the Port List by Begin Time, End Time, Port
Name, or Device Name. The Begin Time and End Time refers to when the recording took place.
To filter the Port List, fill in the variables and click Apply.
To remove all filters click Reset.
36
Chapter 6. Playback
Advanced Search
The Advanced Search page is used to search for video logs on a broad scale.
You can search for video logs by Begin Time, End Time, Port Name, Device
Name, or Port Number. The Begin Time and End Time refers to when the recording took place. After inputting your search data, click Search. Your search results will appear at the bottom of the page, as shown below:
Playback
To playback a video log, select it from the Search Results, then click Play
Selected, or Play All. The video will open in a new window with the Video Log
Viewer application. For information on the Video Log Viewer, see Video Log
37
CCVSR User Manual
Sessions
The Session page lets the administrator and users with User Management permissions see at a glance which users are currently logged into the Video
Session Recorder, and provides information about each of their sessions.
Note: 1. The Session page isn’t available for ordinary users.
2. Users with User Management permissions can only see the sessions of ordinary users.
3. The Category heading lists the type of user who has logged in: SA
(Super Administrator); Admin (Administrator); Normal user (User).
The meanings of the headings at the top of the page are fairly straightforward.
The IP heading refers to the IP address that the user has logged in from; the
Login Time refers to the user logged into the Video Session Recorder, and the
Device and Port headings refer to the device and port a user is currently accessing.
This page also gives the administrator the option of forcing a user logout by selecting the user and clicking Kill Session at the bottom of the page.
The sort order of the information displayed can be changed by clicking the column headings.
38
Chapter 6. Playback
Video Log Viewer
The Video Log Viewer is a build in video player that pops-up when executing video log files for playback. The Video Log Viewer is automatically used to view video logs from the Video Session Recorder’s web sessions or directly from the directory where it was saved. The Video Log Viewer’s playback tools are described below.
When you playback a video log, the Video Log Viewer pops-up, and a screen similar to this one appears:
Toolbar
The toolbar appears below the video and allows you to view information about the video and control playback features. The toolbar hides when no mouse movement is made for 3 seconds. To bring the toolbar into view simply move the mouse. The toolbar functions are described here:
Icon Function
Play: The Play button is used to resume playback of a video log that has been paused.
Pause: The Pause button is used to stop playback of a video log that is being played.
39
CCVSR User Manual
Icon Function
Faster: The Faster button is used to increase the playback speed of a video log. You can increase the speed X2, X4, or X8 of the normal playback rate.
Slower: The Slower button is used to decrease the playback speed of a video log. You can decrease the speed 1/2, 1/4, or 1/8 of the normal playback rate.
Progress Bar: The Progress bar shows how far along you are while viewing video logs. When viewing multiple video logs using the Play All feature, a solid red line on the progress bar represents the end of one video log, and the start of the next.
Placing your mouse over any part of the Progress bar will produce a pop-up display of the time and date when the video log was captured, allowing you to quickly locate and go to reference points.
You can click and drag the progress button forward or back to advance to any point of the video, or click anywhere on the progress bar to advance to a particular point.
Resize Window: At the bottom right hand corner, you can click and drag the bar to resize the window. After doing so if the video doesn’t fit within the resized window, you can scale the video using the Scale
Mode feature (see Scale Mode below).
Note: The entire window can be moved around the screen by holding a left click anywhere on the gray window frame, outside of the Resize
Window area.
Scale Mode: The Scale Mode icon allows you to change the video displays size in the Video Log Viewer’s window. When you click the
Scale Mode icon, three choices appear:
Keep Video Size: Keeps the video display scaled at the original default size.
Keep Video Ratio: Keeps the video display ratio scaled to fit within the resized window.
Scale Video to Window: Scales the video display to the size of the entire window.
Save Video: The Save Video icon allows you to save the current video log to a directory and encrypt it with a password.
To save the video log, click Save Video, choose a directory, name the file, then click Save. After clicking Save the Set Password window will appear, enter a password for the video log file, or leave it blank for no password, then click OK.
Note: Clicking Cancel at the Set Password prompt causes the save process to end and the file is not saved.
Open Video: This icon is used to open previously saved video files.
Click the icon, choose a video log file, then enter the password.
40
Icon
Chapter 6. Playback
Function
Control Panel: When playing videos, in addition to the video image, the Control Panel shows the operations (mouse clicks and keystrokes), username, and IP address of the person logged into the computer, arranged in order of time executed. If multiple people are logged into the KVM port, the Control Panel will display the users, and who conducts each operation.
Click the icon to bring up the Control Panel window, and use the Pin icon located at the top left corner to hold/release the open window.
The User List displays the users logged into the KVM port at the time the video log was recorded.
Full Screen: This icon expands the Video Log Viewer window to fit the the entire screen. To exit Full Screen mode, click the Full Screen icon again.
41
Chapter 7
User Management
Overview
When you select the User Management tab the screen comes up with the Users page displayed:
The page is organized into two main areas: the Sidebar at the left, and the large main panel at the right.
Users and groups appear in the panel at the left of the page. The large panel at the right provides more detailed information at-a-glance for each.
There are separate menu bar entries for Accounts and Groups. Depending on the menu item selected, either Users or Groups are listed in the Sidebar.
The sort order of the information displayed can be changed by clicking the main panel column headings.
The buttons below the main panel are used to manage users and groups, as shown in the sections that follow.
42
Chapter 7. User Management
Users
The Video Session Recorder supports three types of users, as shown in the table, below:
User Type
Super
Administrator
Administrator
User
Role
Access and manage ports and devices. Manage Users, and
Groups. Configure the overall installation. Configure personal working environment.
Access and manage authorized ports and devices. Manage
Users and Groups. Configure personal working environment.
Access authorized ports and devices. Manage authorized ports and devices; configure personal working environment.
Note: Users who have been given permission to do so, may also manage other users.
Adding Users
To add a user, and assign user permissions, do the following:
1. Select Users on the menu bar.
2. Click Add at the bottom of the main panel. The User notebook opens, with the User tab selected:
43
CCVSR User Manual
3. Enter the required information in the appropriate fields. A description of each of the fields is given in the table below:
Field
Username
Password
Confirm Password
Description
Role
Description
From 1 to16 characters are allowed depending on the
Account Policy settings. see Account Policy, page 77.
From 0 to 16 characters are allowed depending on the
Account Policy settings. see Account Policy, page 77
To be sure there is no mistake in the password, you are asked to enter it again. The two entries must match.
Additional information about the user that you may wish to include.
There are three categories: Super Administrator,
Administrator and User. There is no limitation on the number of accounts that can be created in each category.
The Super Administrator is responsible for the overall installation configuration and log maintenance; user management; and device and system management. The
Super Administrator’s permissions (see page 45) are
automatically assigned by the system and cannot be altered.
The default permissions for Administrators include everything except Keyboard/Mouse View, but the permissions can be altered for each Administrator by checking or un-checking any of the permissions checkboxes.
The default permissions for Users include no permissions, but the permissions can be altered for each User by checking or un-checking any of the permissions checkboxes.
Note: Users who have been given User Management privileges cannot access or configure Groups.
44
Chapter 7. User Management
Field
Permissions
Note: For ordinary users, in addition to enabling Device
Management, the user must also be given those rights for each device that he will be allowed to manage.
Assignment, page 54 for details).
Status
Description
Enabling Device Management allows a user to view the
settings and devices on the Device Management tab (see
Enabling User Management allows a user to create, modify, and delete user and group accounts.
Enabling Log allows a user to access the system log (see
Enabling System Management allows a user to access and configure settings in the System Management tab.
Enabling Keyboard/Mouse View allows the user to use the
Control Panel feature from within the Video Log Viewer, which allows you to view the detailed log of keyboard and
mouse operations (mouse clicks, key-strokes), see page 41 for details.
Status allows you to control the user’s account and access to the installation, as follows:
Disable Account lets you suspend a user’s account without actually deleting it, so that it can be easily reinstated in the future.
If you don’t want to limit the time scope of the account, select Account never expires; if you do want to limit the amount of time that the account remains in effect, select
Account expires on, and key in the expiration date.
To make a password permanent, so that the user cannot change it to something else, select User cannot change
password.
For security purposes, administrators may want users to change their passwords from time to time.
If not, select Password never expires. This allows users to keep their current passwords for as long as they like.
If so, select Password expires after, and key in the number of days allowed before the password expires.
Once the time is up, a new password must be set.
4. At this point you can assign the new user to a group by selecting the
Groups tab – the Groups page is discussed on page 50, or you can assign
the user’s device access rights by selecting the Devices tab – the Devices
page is discussed on page 54, or you can assign VSR configuration rights
by selecting the System tab – the System page is discussed on page 56.
5. When your selections have been made click Save.
6. When the Operation Succeeded message appears, click OK.
45
CCVSR User Manual
7. Click Users in the Sidebar to return to the main screen. The new user appears in the Sidebar list and in the main panel, as well.
The Sidebar Users list can expand and collapse. If the list is expanded, click the minus symbol ( – ) next to the Users icon to collapse it; if it is collapsed there is a plus symbol ( + ) next to the icon. Click the plus symbol to expand it.
The icon for super Administrators has two red bands; the icon for
Administrators has one black band.
The large main panel shows the user’s name; the description that was given when the account was created; and whether the account is currently active or has been disabled.
Modifying User Accounts
To modify a user account, do the following:
1. In the Sidebar User list, click the user’s name.
– or –
In the main panel, select the user’s name.
2. Click Modify.
3. In the User page that comes up, make your changes, then click Save.
Note: The User page is discussed on page 43; the Groups page is discussed on
page 50, the Devices page is discussed on page 54.
Deleting User Accounts
To delete a user account, do the following:
1. In the main panel, select the user’s name.
2. Click Delete.
3. Click OK.
46
Chapter 7. User Management
Groups
Groups allow administrators to easily and efficiently manage users and devices. Since device access rights apply to anyone who is a member of the group, administrators need only set them once for the group, instead of having to set them for each user individually. Multiple groups can be defined to allow some users access to specific devices, while restricting other users from accessing them.
Creating Groups
To Create a group, do the following:
1. Select Groups on the menu bar.
2. Click Add at the bottom of the main panel. The Group notebook opens, with the Group tab selected:
3. Enter the required information in the appropriate fields. A description of each of the fields is given in the table below:
Field Description
Group Name A maximum of 16 characters is allowed.
Description
Permissions
Additional information about the user that you may wish to include. A maximum of 63 characters is allowed.
Permissions and restrictions for groups are set by checking the appropriate boxes. These are the same permissions as the ones
specified for Users. See Permissions, page 47 for details.
4. At this point you can assign users to the group by selecting the Members
tab – the Members page is discussed on page 52, or you can assign the
47
CCVSR User Manual group’s device access rights by selecting the Devices tab – the Devices
page is discussed on page 54, or you can assign VSR configuration rights
by selecting the System tab – the System page is discussed on page 56.
5. When your selections have been made click Save.
6. When the Operation Succeeded message appears, click OK.
7. Click Group in the Sidebar to return to the main screen. The new group appears in the Sidebar Group list and in the main panel.
The Sidebar Group list can expand and collapse. If the list is expanded, click the minus symbol ( – ) next to the Users icon to collapse it; if it is collapsed there is a plus symbol ( + ) next to the icon. Click the plus symbol to expand it.
The large main panel shows the group’s name, and the description that was given when the group was created (the Status column is inactive).
Note: You must perform Step 7 before attempting to add a new group, or else the new group you are creating will replace the group you just finished creating.
Modifying Groups
To modify a group, do the following:
1. In the Sidebar Group list, click the group’s name.
– or –
In the main panel, select the group’s name.
2. Click Modify.
3. Click OK.
4. In the Group notebook that comes up, make your changes, then click Save.
Note: The Group page is discussed on page 47; the Members page is
discussed on page 52, The Devices page is discussed on page 54, and
the System page is discussed on page 56.
48
Deleting Groups
To delete a group, do the following:
1. In the Sidebar, click the Groups icon.
2. In the main panel, select the group’s name.
3. Click Delete.
4. Click OK.
Chapter 7. User Management
49
CCVSR User Manual
Users and Groups
There are two ways to manage users and groups: from the Users notebook; and from the Group notebook.
Note: Before you can assign users to groups, you must first create them.
Assigning Users to a Group From the User’s Notebook
To assign a user to a group from the User’s notebook, do the following:
1. In the Sidebar User list, click the user’s name.
– or –
In the main panel, select the user’s name.
2. Click Modify.
3. In the User notebook that comes up, select the Groups tab. A screen, similar to the one below, appears:
4. In the Available column, select the group that you want the user to be in.
5. Click the Right Arrow to put the group’s name into the Selected column.
6. Repeat the above for any other groups that you want the user to be in.
7. Click Save when you are done.
Note: If a user has permissions in addition to the ones assigned to the group, the user keeps those permissions in addition to the group ones.
50
Chapter 7. User Management
Removing Users From a Group From the User’s Notebook
To remove a user from a group from the User’s notebook, do the following:
1. In the Sidebar User list, click the user’s name.
– or –
In the main panel, select the user’s name.
2. Click Modify.
3. In the User notebook that comes up, select the Groups tab. A screen, similar to the one below, appears:
4. In the Selected column, select the group that you want to remove the user from.
5. Click the Left Arrow to remove the group’s name from the Selected column. (It goes back into the Available column.)
6. Repeat the above for any other groups that you want to remove the user from.
7. Click Save when you are done.
51
CCVSR User Manual
Assigning Users to a Group From the Group’s Notebook
To assign a user to a group from the Group notebook, do the following:
1. In the Sidebar Group list, click the group’s name.
– or –
In the main panel, select the group’s name.
2. Click Modify.
3. In the Group notebook that comes up, select the Members tab. A screen, similar to the one below, appears:
4. In the Available column, select the user that you want to be a member of the group.
5. Click the Right Arrow to put the user’s name into the Selected column.
6. Repeat the above for any other users that you want to be members of the group.
7. Click Save when you are done.
Note: If a user has permissions in addition to the ones assigned to the group, the user keeps those permissions in addition to the group ones.
52
Chapter 7. User Management
Removing Users From a Group From the Group’s Notebook
To remove a user from a group from the Group’s notebook, do the following:
1. In the Sidebar Group list, click the group’s name
– or –
In the main panel, select the group’s name.
2. Click Modify.
3. In the Group notebook that comes up, select the Members tab. A screen, similar to the one below, appears:
4. In the Selected column, select the user that you want to remove from the group.
5. Click the Left Arrow to remove the user’s name from the Selected column. (It goes back into the Available column.)
6. Repeat the above for any other users that you want to remove from the group.
7. Click Save when you are done.
53
CCVSR User Manual
Device Assignment
When a user logs in to the Video Session Recorder, the interface comes up with the Playback page displayed. All the ports that the user is permitted to access are listed in the Port List at the left of the page. Access permissions for ports and the devices connected to them are assigned on a port-by-port basis from the User or Group list on the Sidebar of the User Management page.
Assigning Device Permissions From the User’s Notebook
To assign device permissions to a user from the User’s notebook, do the following:
1. In the Sidebar User list, click the user’s name.
– or –
In the main panel, select the user’s name.
2. Click Modify.
3. In the User notebook that comes up, select the Devices tab. A screen, similar to the one below, appears:
4. Make your permission settings for each port according to the information provided below:
Name: Each port accessible to the user is listed under the Names column.
Video: Selecting this checkbox gives a user the ability to search and view video logs for a port.
54
Chapter 7. User Management
Config: Selecting this checkbox gives a user the ability to enable/ disable ports for devices found in the Device Management tab.
Permissions are applied from the top down, therefore you must select a KVM device in order for the individual ports below it to be available for access.
View Log: Selecting this checkbox allows a user the ability to view system logs for a KVM device from the Logs tab.
5. When you have finished making your choices, click Save.
6. In the confirmation popup that appears, click OK.
Assigning Device Permissions From the Group’s Notebook
To assign device permissions to a Group of users, do the following:
1. In the Sidebar Groups list, click the group’s name.
– or –
In the main panel, select the group’s name.
2. Click Modify.
3. In the Groups notebook that comes up, select the Devices tab.
4. The screen that comes up is the same one that appears in the User’s notebook. The only difference is that whatever settings you make apply to all members of the group instead of just one individual member.
Make your device assignments according to the information described
under Assigning Device Permissions From the User’s Notebook, page 54.
55
CCVSR User Manual
System Permissions
Systems permissions allows administrators to give users or groups the ability to make systems configuration changes from the System Management tab.
Assigning System Permissions From the User’s Notebook
To assign systems configuration permissions to a user from the User's notebook, do the following:
1. In the Sidebar User list, click the user’s name.
– or –
In the main panel, select the user’s name.
2. Click Modify.
3. In the User notebook that comes up, select the System tab. A screen, similar to the one below, appears:
4. Select the Video Session Recorder (VSR) you want to allow System
Configuration changes on.
5. Click the Config checkbox.
6. Click Save.
56
Chapter 7. User Management
Assigning System Permissions From the Group’s Notebook
To assign systems configuration permissions to a user from the Group’s notebook, do the following:
1. In the Sidebar Groups list, click the group’s name.
– or –
In the main panel, select the group’s name.
2. Click Modify.
3. In the Group notebook that comes up, select the System tab. A screen, similar to the one below, appears:
4. Select the Video Session Recorder (VSR) you want to allow System
Configuration changes on.
5. Click the Config checkbox.
6. Click Save.
57
Chapter 8
Device Management
Overview
The purpose of the Device Management tab is to add KVM devices and configure ports through which the Video Session Recorder can record video logs. The Device Management tab opens with Devices selected in the Sidebar, and the main page showing a list of KVM devices which have been added:
Recording KVM Ports
To record video logs you must add a KVM switch, then enable the switch and/ or ports on the KVM’s Device Settings page. Enabled ports are recorded by the
Video Session Recorder every time they are accessed through the KVM switch, and are saved as a video log file. Logs are viewed from the Playback tab. There is no limit to the number of KVM devices that you can add or ports you can enable. The Video Session Recorder can simultaneously record a maximum of
12 ports at one time, across multiple KVM devices.
58
Chapter 8. Device Management
Adding KVM Devices
To add a KVM switch to the KVM Device list, do the following:
1. From the Device Management page, click Add.
A pop-up window appears:
2. Fill in the IP address and Service Port number of the KVM switch you are adding, and click Add.
3. The KVM switch will appear in the Devices list on the sidebar, and on the
Device Management main page.
Note: 1. After adding a KVM switch check to be sure the Status column of the
KVM device is Online.
2. An Offline status indicates the KVM device can’t be reached over the network. Check that the IP address and Service Port numbers are correct, and that the KVM switch is online.
Enabling KVM Devices
To enable the KVM switch to record video sessions, do the following:
1. In the sidebar Devices list, click the KVM device name.
2. Under Enable/Disable put a check in the Device box.
3. The KVM switch will now record video sessions anytime a port on the
KVM switch is accessed. To enable/disable individual ports, see
Configuring KVM Ports on the next page.
59
CCVSR User Manual
Configuring KVM Ports
To enable a KVM Port, so that the Video Session Recorder records it when accessed through the switch, do the following:
1. In the sidebar Devices list, click the KVM device name.
2. The KVM’s Devices Settings page appears:
3. Enable the ports that you want the Video Session Recorder to record by checking the boxes. Video Logs will be created every time the enabled ports are accessed through the KVM switch.
4. After configuring the KVM’s Device Settings, click Save.
A description of the Device Settings fields are given in the table below.
Type
Field
Name
Description
IP
Service Port
Explanation
Describes the switch device type for your reference.
Provides the name of the KVM switch for your reference.
Enter information about the KVM device that you want to include.
Enter the IP address of the KVM switch here.
Enter the service port number of the KVM switch here.
Enable/Disable Checking a box enables the port, so that when it is accessed through the KVM switch, a video log is recorded.
If a port or device’s checkbox is not selected, it is disabled, and no video logs will be recorded for that port.
You can enable all ports by selecting the KVM Device’s checkbox, or individual ports by selecting each port you want to enable.
60
Chapter 8. Device Management
Deleting KVM Devices
To delete a KVM Switch from the KVM Device list, do the following:
1. In the main panel, select the KVM device you want to delete.
2. Click Delete.
61
Chapter 9
Logs
Overview
The Video Session Recorder logs all the events that take place on it. To view the contents of the log, click the Log tab. The Latest Logs page, similar to the one below, appears:
Latest Logs
The Latest Logs page displays events that take place on the Video Session
Recorder, and provides a breakdown of the time, severity, user, and a description of each event.
The log file tracks a maximum of 512 events. When the limit is reached, the oldest events get discarded as new events come in. You can filter the event logs by System, or KVM device by selecting either from the sidebar tree list.
62
Chapter 9. Logs
Search Logs
The Search Logs page allows you to search logs by Time, Information, and
Priority. In addition, you can export your search into a custom log file. When you click Search Logs from the menu bar, the following screen appears:
The purpose of the fields found at the bottom of the search page are described in the following table:
Field
Time
Explanation
This feature lets you search for events that occurred at specific times, as follows:
Today Only: Only the events for the current day are displayed.
Start Date/Time: Searches for events from a specific date and time to the present. After checking Start Date/
Time, click inside the text box in order to bring up the calendar. When you have made your calendar choices, click the A icon at the lower right of the calendar panel.
Set the date and time that you want the search to start from. All events from the Start date/time to the present are displayed.
End Date/Time: Searches for events from a specific date and time to a specific date and time. First select the
Start Date/Time (described above); check End Date/
Time to set the ending date and time.
After checking End Date/Time, click inside the text box in order to bring up the calendar. When you have made your calendar choices, click the A icon at the lower right of the calendar panel.
63
CCVSR User Manual
Information
Field
Priority
Search
Reset
Export Log
Explanation
Searches for a particular word or string. Key the word or string into the Information text box. Only events containing that word or string are displayed. Wildcards (? for single characters; * for multiple characters) and the keyword or are supported.
E.g., h*ds would return hands and hoods; h?nd would return hand and hind, but not hard; h*ds or h*ks would return hands and hooks.
Searches based on the severity rating of the event. Least events appear in black; Less events appear in blue; Most events appear in red.
First put a check in the Priority checkbox; then check the severity options you want to search for (you can check more than one item). Only events that match the severity ratings you specified appear in the display.
Click to apply the filter choices.
Click this button to clear the entries in the dialog box and start with a clean slate.
Clicking Export Log will bring up window giving you the option to Save or Open the search log as a *.csv file.
64
Chapter 9. Logs
Notification Settings
The Notification Settings page lets you decide which events trigger a notification, and how the notifications are sent out:
Notifications can be sent via SNMP trap, SMTP email, written to the SysLog file, or any combination of the three. A check mark (
√
) indicates that notification of the event is permitted for the method specified in the column heading; an empty box indicates that notification is not restricted.
Note: In any of the columns, you can use Shift-Click or Ctrl-Click to select a group of events. Clicking to permit/restrict any one of them causes all of them to change in unison.
65
Chapter 10
System Management
Overview
The Systems Management tab is used to view and manage the Video Session
Recorder’s system settings. When you select the System Management tab the screen comes up with the System Info page displayed:
The page is organized into two main areas: the Sidebar at the left, and the large main panel at the right.
The Log Servers list appears in the panel at the left of the page. The large panel at the right provides detailed information about the menu or sidebar selection
There are separate menu bar options selecting Log Servers or a Video
Session Recorder from the sidebar list
With Log Servers selected you will see System Info, Network, ANMS, and
Security on the menu bar.
When a Video Session Recorder is selected from the sidebar, it's Log
Server Settings page appears.
66
Chapter 10. System Management
System Info
When you select the System Management tab the System Info page appears with
General information about the local Video Session Recorder, as shown and described below:
Item
Server Name
Version Number
Server MAC
IP Address
IPV6 Address
Meaning
Displays the computer name of the server hosting the
Video Session Recorder application.
Displays the Video Session Recorder’s firmware version.
Displays the MAC address of the computer hosting the
Video Session Recorder application.
Displays the Video Session Recorder’s IP address.
Displays the Video Session Recorder’s IPV6 address.
VSR-Local
The VSR-Local device found on the sidebar is the system settings page for the local Video Session Recorder. Selecting this device allows you to configure the settings for IP Address, Name, Description, and local VSR Space for saving
video session files. For more information on these settings see Log Servers, page 83 for details.
67
CCVSR User Manual
Network
The Network page is used to specify the service ports used to access the Video
Session Recorder, as shown here:
As a security measure, if a firewall is being used, the Administrator can specify the port numbers that the firewall will allow. If a port other than the default is used, users must specify the port number as part of the IP address when they log in. If an invalid port number (or no port number) is specified, the Video
Session Recorder will not be found. An explanation of the fields is given in the table below:
Field
Program
HTTP
HTTPS
Explanation
This is the port number to connect a computer running the VSR application as a Secondary Server, to a Video
Log Primary Server. The default is 9002.
The port number for a browser login. The default is 9080.
The port number for a secure browser login. The default is 9443.
For Example: To access the Video Session Recorder with an IP address of
192.168.0.100, using a secure browser login (https), enter: https://192.168.0.100:9443
Note: 1. Valid entries for all of the Service Ports are from 1–65535.
2. Service ports cannot have the same value. You must set a different value for each one.
3. If there is no firewall (on an Intranet, for example), it doesn’t matter what these numbers are set to, since they have no effect.
68
Chapter 10. System Management
ANMS
The ANMS (Advanced Network Management Settings) page is used to set up login authentication and authorization management from external sources. It is organized as a notebook with two tabs – each with a series of related panels, as described, below:
Event Destination
SMTP Settings
To have the Video Session Recorder email reports from the SMTP server to you, do the following:
1. Enable the Enable report from the following SMTP server, and key in either the IPv4 address, IPv6 address, or domain name of the SMTP server.
2. If your server requires a secure SSL connection, put a check in the My
server requires secure connection (SSL) checkbox.
3. If your server requires authentication, put a check in the My server
requires authentication checkbox, and key in the appropriate account information in the Account Name and Password fields.
69
CCVSR User Manual
4. Key in the email address of where the report is being sent from in the
From field.
Note: 1. Only one email address is allowed in the From field, and it cannot exceed 64 Bytes.
2. 1 Byte = 1 English alphanumeric character.
5. Key in the email address (addresses) of where you want the SMTP reports sent to in the To field.
Note: If you are sending the report to more than one email address, separate the addresses with a semicolon. The total cannot exceed
256 Bytes.
SNMP Server
To be notified of SNMP trap events, do the following:
1. Check Enable SNMP Agent.
2. Key in either the IPv4 address, IPv6 address, or domain name of the computer to be notified of SNMP trap events.
3. Key in the port number. The valid port range is 1–65535.
Note: The logs that are notified of SNMP trap events are configured on the
Notification Settings page under the Log tab. See Notification
Settings, page 65 for details.
Syslog Server
To record all the events that take place on the Video Session Recorder and write them to a Syslog server, do the following:
1. Check Enable.
2. Key in either the IPv4 address, IPv6 address, or domain name of the
Syslog server.
3. Key in the port number. The valid port range is 1-65535.
70
Authentication
Chapter 10. System Management
Disable Local Authentication
Selecting this option disables login authentication on the Video Session
Recorder. The server can only be accessed using LDAP, LDAPS, MS
Active Directory, or RADIUS authentication.
RADIUS Settings
To allow authentication and authorization for the Video Session Recorder through a RADIUS server, do the following:
1. Check Enable.
2. Fill in the IP addresses and service port numbers for the Preferred and
Alternate RADIUS servers. You can use the IPv4 address, the IPv6 address or the domain name in the IP fields.
3. In the Timeout field, set the time in seconds that the Video Session
Recorder waits for a RADIUS server reply before it times out.
4. In the Retries field, set the number of allowed RADIUS retries.
5. In the Shared Secret field, key in the character string that you want to use for authentication between the Video Session Recorder and the
RADIUS Server. A minimum of 6 characters is required.
71
CCVSR User Manual
6. On the RADIUS server, Users can be authenticated with any of the following methods:
Set the entry for the user as su/xxxx
Where xxxx represents the Username given to the user when the account was created on the Video Session Recorder.
Use the same Username on both the RADIUS server and the
Video Session Recorder.
Use the same Group name on both the RADIUS server and the
Video Session Recorder.
Use the same Username/Group name on both the RADIUS server and the Video Session Recorder.
In each case, the user’s access rights are the ones assigned that were assigned when the User of Group was created on the Video Session
Recorder. (See Adding Users, page 43.)
LDAP / LDAPS Authentication and Authorization Settings
To allow authentication and authorization for the Video Session Recorder via LDAP / LDAPS, refer to the information in the table, below:
Enable
Item
Type
LDAP Server IP and Port
Admin DN
Admin Name
Password
Search DN
Timeout
Action
Put a check in the Enable checkbox to allow LDAP / LDAPS authentication and authorization.
Click a radio button to specify whether to use LDAP or LDAPS.
Fill in the IP address and port number for the LDAP or LDAPS server.
You can use the IPv4 address, the IPv6 address or the domain name in the LDAP Server field.
For LDAP, the default port number is 389; for LDAPS, the default port number is 636.
Consult the LDAP / LDAPS administrator to ascertain the appropriate entry for this field. For example, the entry might look like this: ou=kn4132,dc=aten,dc=com
Key in the LDAP administrator’s username.
Key in the LDAP administrator’s password.
Set the distinguished name of the search base. This is the domain name where the search starts for user names.
Set the time in seconds that the Video Session Recorder waits for an LDAP or LDAPS server reply before it times out.
72
Chapter 10. System Management
On the LDAP / LDAPS server, Users can be authenticated with any of the following methods:
With MS Active Directory schema.
Note: If this method is used, the LDAP schema for MS Active Directory must be extended.See LDAP Server Configuration, page 71, for details.
Without schema – Only the Usernames used on the Video Session
Recorder are matched to the names on the LDAP / LDAPS server. User privileges are the same as the ones configured on the switch.
Without schema – Only Groups in AD are matched. User privileges are the ones configured for the groups he belongs to on the switch.
Without schema – Usernames and Groups in AD are matched. User privileges are the ones configured for the User and the Groups he belongs to on the switch.
73
CCVSR User Manual
Security
The Security page is divided into 5 panels, as described in the sections that follow.
Login Failures
For increased security, the Login Failures section allows administrators to set policies governing what happens when a user fails to log in successfully.
To set the Login Failures policy, check the Enable checkbox (the default is for
Login Failures to be enabled). The meanings of the entries are explained below.
Entry
Allowed
Timeout
Lock Client PC
Lock Account
Explanation
Sets the number of consecutive failed login attempts that are permitted from a remote computer. The default is 5 times.
Sets the amount of time a remote computer must wait before attempting to login again after it has exceeded the number of allowed failures. The default is 3 minutes.
If this is enabled, after the allowed number of failures have been exceeded, the computer attempting to log in is automatically locked out. No logins from that computer will be accepted. The default is enabled.
Note: This function relates to the client computer’s IP. If the IP is changed, the computer will no longer be locked out.
If this is enabled, after the allowed number of failures have been exceeded, the user attempting to log in is automatically locked out. No logins from the username and password that have failed will be accepted. The default is enabled.
Note: If Login Failures is not enabled, users can attempt to log in an unlimited number of times with no restrictions. For security purposes, we recommend that you enable this function and enable the lockout policies.
74
Chapter 10. System Management
Filter
IP Filtering
IP Filters control access to the Video Session Recorder based on the IP addresses of the client computers attempting to connect. A maximum of
100 IP filters are allowed. If any filters have been configured, they appear in the IP Filter list box.
To enable IP filtering, Click to put a check mark in the IP Filter Enable checkbox.
If the include button is checked, all the addresses within the filter range are allowed access; all other addresses are denied access.
If the exclude button is checked, all the addresses within the filter range are denied access; all other addresses are allowed access.
75
CCVSR User Manual
Adding Filters
To add an IP filter, do the following:
1. Click Add. A dialog box similar to the one below appears:
2. Key the address you want to filter in the From: field.
3. Key in the end number of the range in the To: field.
To filter a single IP address, key the same address in both the From and
To fields.
4. After filling in the address, click OK.
5. Repeat these steps for any additional IP addresses you want to filter.
Modifying Filters
To modify a filter, select it in the IP Filter list and click Modify. The
Modify dialog box is similar to the Add dialog box. When it comes up, simply delete the old address(es) and replace it with the new one(s).
Deleting Filters
To delete a filter, select it in the IP Filter list and click Delete.
76
Chapter 10. System Management
Account Policy
In the Account Policy section, system administrators can set policies governing usernames and passwords.
The meanings of the Account Policy entries are explained in the table below:
Entry Explanation
Minimum Username Length Sets the minimum number of characters required for a username. Acceptable values are from 1 – 16. The default is 6.
Minimum Password Length Sets the minimum number of characters required for a password. Acceptable values are from 0 – 16. A setting of
0 means that no password is required. Users can login with only a Username. The default is 6.
Password Must Contain At
Least
Disable Duplicate Login
Checking any of these items requires users to include at least one uppercase letter, one lowercase letter or one number in their password.
Note: This policy only affects user accounts created after this policy has been enabled, and password changes to existing user accounts. Users accounts created before this policy was enabled, with no change to the existing password, are not affected.
Check this to prevent users from logging in with the same account at the same time.
77
CCVSR User Manual
Private Certificate
When logging in over a secure (SSL) connection, a signed certificate is used to verify that the user is logging in to the intended site. For enhanced security, the
Private Certificate section allows you to use your own private encryption key and signed certificate, rather than the default ATEN certificate.
There are two methods for establishing your private certificate: generating a self-signed certificate; and importing a third-party certificate authority (CA) signed certificate.
Generating a Self-Signed Certificate
If you wish to create your own self-signed certificate, a free utility –
openssl.exe – is available for download over the web. See Self-Signed
Private Certificates, page 92 for details about using OpenSSL to generate
your own private key and SSL certificate.
Obtaining a CA Signed SSL Server Certificate
For the greatest security, we recommend using a third party certificate authority (CA) signed certificate. To obtain a third party signed certificate, go to a CA (Certificate Authority) website to apply for an SSL certificate.
After the CA sends you the certificate and private encryption key, save them to a convenient location on your computer.
Importing the Private Certificate
To import the private certificate, do the following:
1. Click Browse to the right of Private Key; browse to where your private encryption key file is located; and select it.
2. Click Browse to the right of Certificate; browse to where your certificate file is located; and select it.
3. Click Upload to complete the procedure.
Note: 1. Clicking Restore Default returns the device to using the default
ATEN certificate.
2. Both the private encryption key and the signed certificate must be imported at the same time.
78
Chapter 10. System Management
Certificate Signing Request
The Certificate Signing Request (CSR) section provides an automated way of obtaining and installing a CA signed SSL server certificate.
To perform this operation do the following:
1. Click Create CSR. The following dialog box appears:
2. Fill in the form – with entries that are valid for your site – according to the example information in the following table:
Information
Country (2 letter code)
State or Province
Locality
Organization
Unit
Common Name
Email Address
Example
TW
Taiwan
Taipei
Your Company, Ltd.
Tech Department mycompany.com
Note: This must be the exact domain name of the site that you want the certificate to be valid for. If the site’s domain name is www.mycompany.com, and you only specify mycompany.com, the certificate will not be valid.
79
CCVSR User Manual
3. After filling in the form (all fields are required), click Create.
A self-signed certificate based on the information you just provided is now stored on the CCVSR.
4. Click Get CSR, and save the certificate file (csr.cer) to a convenient location on your computer.
This is the file that you give to the third party CA to apply for their signed
SSL certificate.
5. After the CA sends you the certificate, save it to a convenient location on your computer. Click Browse to locate the file; then click Upload to store it on the CCVSR.
Note: When you upload the file, the CCVSR checks the file to make sure the specified information still matches. If it does, the file is accepted; if not, it is rejected.
If you want to remove the certificate (to replace it with a new one because of a domain name change, for example), simply click Remove CSR.
80
Chapter 10. System Management
Video Session Recorder
The Video Session Recorder page is used to add Secondary VSR Servers available on the network, so that you can manage them. Secondary VSR Servers are used to save video log files on alternative computers in order to consolidate disk space across different computers. To configure a secondary computer to
work as a Secondary VSR Server, see Settings, page 15 for details. When you
select Video Session Recorder from the System Management menu bar, the following screen appears:
From the Video Session Recorder menu page you can:
Add or Delete VSR Servers
Enable or Disable VSR Servers
Set the Maximum Recording Time
Adding Secondary VSR Servers
Adding Secondary VSR Severs allows you to configure their Log Server
Settings. The Secondary VSR Server you are adding must be on a computer available over the network. To add a VSR Server, do the following:
1. Click Add. A pop-up screen appears:
81
CCVSR User Manual
2. Select a VSR Server from the list and click Add Selected, or click Add
All.
3. The VSR Server will now appear on the main page and sidebar list.
Deleting Secondary VSR Servers
To delete a VSR server, do the following:
1. Select a VSR Server from the list.
2. Click Delete.
Enable/Disable Secondary VSR Servers
To enable/disable a VSR server, do the following:
1. Select the VSR Server from the main page, check to Enable, or uncheck to
Disable, and click Save.
Maximum Recording Time
This option protects video files for the [past] number of days entered- from being overwritten. The option can be set anywhere between 3~180 days.
Setting the maximum recording time tells the Video Session Recorder how many days of video files to save if the disk becomes full and the Video Session
Recorder needs to overwrite old files. The default setting is 30 days.
For example, if you set the maximum recording time to 7 days, and after 14 days the disk becomes full, the Video Session Recorder will over-write only the oldest video files - that are older then 7 days; and leaves all video files created in the past 7 days untouched.
82
Chapter 10. System Management
Log Servers
The Log Servers lists Secondary VSR Servers in the sidebar which have been
added from the Video Session Recorder menu bar (see Adding Secondary VSR
Selecting a Secondary VSR Server from the sidebar list brings up the Video
Session Recorder Settings page for that server, as shown and described below:
The page settings are explained in the following table:
IP
Name
Description
Drive
Capacity
Available Space
VSR Space
Item
Used Percentage
Description
Displays the IP address of the Video Session Recorder.
This field allows you to enter a name for the Video
Session Recorder.
This field allows you to enter additional information about the Video Session Recorder that you may wish to include.
The Drive column lists the local disks available for storing video logs.
The Capacity column shows the total amount of disk space available when the drive is empty.
The Available Space column shows the amount of disk space currently available to store data on the drive, in gigabytes.
In this field enter the maximum amount of space you want the Video Session Recorder to use to store recorded video logs on the drive. If the video logs exceed the VSR Space provided, the Video Session Recorder will stop recording video logs until more space is made available.
If the Available Space is less then 2 GB’s the VSR will create an event log notification – when the Disk Full event is enabled on the Logs - Notification Settings page
(see Notification Settings, page 65 for details).
Displays the percentage of VSR Space being used.
83
Chapter 11
Preferences
Overview
The Preferences tab allows users to set up their own individual working environments. The Video Session Recorder stores a separate configuration record for each user profile, and sets up the working configuration according to the Username that was keyed into the Login dialog box:
The page settings are explained in the following table:
Language
Settings
Logout Timeout
Function
The drop-down menu allows you to change the language of the CCVSR interface. The choices are English,
Chinese (Simplified), Chinese (Traditional), Japanese,
Korean.
If there is no user input for the amount of time set with this function, the user is automatically logged out. A login is necessary before the Video Session Recorder can be accessed again.
The default is 30 minutes.
84
Chapter 11. Preferences
Settings
Video Search Results Per
Page
Maximum Video Clip Time
Gap
Welcome Message
Change Password
Function
This sets the number of search results that will appear after submitting video log searches from the Playback tab. Key in a value from 20 – 100.
The default is 20 search results.
Specify the maximum amount of time in Minutes/
Seconds that can go by with no action on a port before the Video Session Recorder pauses recording. The moment action continues, the Video Session Recorder will resume recording, and generate a single seamless video log file.
The default is 5 seconds.
You can choose to Hide or Show the welcome message displayed in the submenu bar.
The default is disabled.
To change a user’s password, key in the old password and new password into their input boxes; key the new password into the Confirm input box, then click Change
Password to apply the change.
85
Appendix
Safety Instructions
General
Read all of these instructions. Save them for future reference.
Follow all warnings and instructions marked on the device.
Do not place the device on any unstable surface (cart, stand, table, etc.). If the device falls, serious damage will result.
Do not use the device near water.
Do not place the device near, or over, radiators or heat registers.
The device cabinet is provided with slots and openings to allow for adequate ventilation. To ensure reliable operation, and to protect against overheating, these openings must never be blocked or covered.
The device should never be placed on a soft surface (bed, sofa, rug, etc.) as this will block its ventilation openings. Likewise, the device should not be placed in a built in enclosure unless adequate ventilation has been provided.
Never spill liquid of any kind on the device.
Unplug the device from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
The device should be operated from the type of power source indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
The device is designed for IT power distribution systems with 230V phase-to-phase voltage.
To prevent damage to your installation it is important that all devices are properly grounded.
The device is equipped with a 3-wire grounding type plug. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not attempt to defeat the purpose of the grounding-type plug. Always follow your local/national wiring codes.
Do not allow anything to rest on the power cord or cables. Route the power cord and cables so that they cannot be stepped on or tripped over.
86
Appendix
If an extension cord is used with this device make sure that the total of the ampere ratings of all products used on this cord does not exceed the extension cord ampere rating. Make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes.
To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).
Position system cables and power cables carefully; Be sure that nothing rests on any cables.
Never push objects of any kind into or through cabinet slots. They may touch dangerous voltage points or short out parts resulting in a risk of fire or electrical shock.
Do not attempt to service the device yourself. Refer all servicing to qualified service personnel.
If the following conditions occur, unplug the device from the wall outlet and bring it to qualified service personnel for repair.
The power cord or plug has become damaged or frayed.
Liquid has been spilled into the device.
The device has been exposed to rain or water.
The device has been dropped, or the cabinet has been damaged.
The device exhibits a distinct change in performance, indicating a need for service.
The device does not operate normally when the operating instructions are followed.
Only adjust those controls that are covered in the operating instructions.
Improper adjustment of other controls may result in damage that will require extensive work by a qualified technician to repair.
Do not connect the RJ-11 connector marked “UPGRADE” to a public telecommunication network.
87
CCVSR User Manual
Technical Support
International
For online technical support – including troubleshooting, documentation, and software updates: http://support.aten.com
For telephone support, see Telephone Support, page iii.
North America
Email Support
Online
Technical
Support
Troubleshooting
Documentation
Software Updates
Telephone Support [email protected]
http://www.aten-usa.com/support
1-888-999-ATEN ext 4988
When you contact us, please have the following information ready beforehand:
Product model number, serial number, and date of purchase.
Your computer configuration, including operating system, revision level, expansion cards, and software.
Any error messages displayed at the time the error occurred.
The sequence of operations that led up to the error.
Any other information you feel may be of help.
88
USB Authentication Key Specifications
Environment
Function
Operating Temp.
Physical
Properties
Storage Temp.
Humidity
Composition
Weight
Dimensions
Key
0–40 o C
-20–60 o
C
0–80% RH, Non-condensing
Metal and Plastic
14 g
8.36 x 2.77 x 1.37cm
Appendix
Supported KVM Over the NET™ Switches
Supported KVM Switches that the Video Log Sever requires to record port access connections for the creation of video logs, include the following:
KN2116A / KN2132 / KN4116 / KN4132
KN2116v / KN2132v / KN4116v / KN4132v
KN2124v / KN4124v / KN2140v / KN4140v
KN1108v / KN1116v
Note: These are the supported devices available when the user manual was initially published. Please visit our web page to see if additional devices have been added since this manual was published.
89
CCVSR User Manual
Windows XP Installation
If you are installing the CCVSR on a computer running Windows XP you need to install IPv6 first. To install IPv6 on Windows XP, do the following;
1. Click the Start Menu - Run, and the following screen appears:
2. In the text box type: “cmd”, and click OK. A command prompt appears:
3. At the command prompt type: “cmd ipv6 install” and press [Enter].
4. IPv6 will automatically install and you can continue with the CCVSR
90
Appendix
Trusted Certificates
Overview
When you try to log in to the device from your browser, a Security Alert message appears to inform you that the device’s certificate is not trusted, and asks if you want to proceed.
The certificate can be trusted, but the alert is triggered because the certificate’s name is not found on the Microsoft list of Trusted Authorities. You can ignore the warning and click:
91
CCVSR User Manual
Self-Signed Private Certificates
If you wish to create your own self-signed encryption key and certificate, a free utility – openssl.exe – is available for download over the web at www.openssl.org. To create your private key and certificate do the following:
1. Go to the directory where you downloaded and extracted openssl.exe to.
2. Run openssl.exe with the following parameters: openssl req -new -newkey rsa:1024 -days 3653 -nodes -x509
-keyout CA.key -out CA.cer -config openssl.cnf.
Note: 1. The command should be entered all on one line (i.e., do not press
[Enter] until all the parameters have been keyed in).
2. If there are spaces in the input, surround the entry in quotes (e.g.
”ATEN International”).
To avoid having to input information during key generation the following additional parameters can be used:
/C /ST /L /O /OU /CN /emailAddress.
Examples
openssl req -new -newkey rsa:1024 -days 3653 -nodes -x509
-keyout CA.key -out CA.cer -config openssl.cnf -subj
/C=yourcountry/ST=yourstateorprovince/L=yourlocationor city/O=yourorganiztion/OU=yourorganizationalunit/
CN=yourcommonname/[email protected]
openssl req -new -newkey rsa:1024 -days 3653 -nodes -x509
-keyout CA.key -out CA.cer -config openssl.cnf -subj
/C=CA/ST=BC/L=Richmond/O="ATEN International"/OU=ATEN
/CN=ATEN/[email protected]
Importing the Files
After the openssl.exe program completes, two files – CA.key (the private key) and CA.cer (the self-signed SSL certificate) – are created in the directory that you ran the program from. These are the files that you upload in the Private
Certificate panel of the Security page (See Security, page 74, and Private
92
Appendix
Limited Warranty
ALTUSEN warrants this product against defects in material or workmanship for a period of one
(1) year from the date of purchase. If this product proves to be defective, contact ALTUSEN's support department for repair or replacement of your unit. ALTUSEN will not issue a refund.
Return requests can not be processed without the original proof of purchase.
When returning the product, you must ship the product in its original packaging or packaging that gives an equal degree of protection. Include your proof of purchase in the packaging and the RMA number clearly marked on the outside of the package.
This warranty becomes invalid if the factory-supplied serial number has been removed or altered on the product.
This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence or modification of any part of the product. This warranty does not cover damage due to improper operation or maintenance, connection to improper equipment, or attempted repair by anyone other than ALTUSEN. This warranty does not cover products sold AS IS or WITH
FAULTS.
IN NO EVENT SHALL ALTUSEN'S LIABILITY EXCEED THE PRICE PAID FOR THE
PRODUCT. FURTHER, ALTUSEN SHALL NOT BE RESPONSIBLE FOR DIRECT,
INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THE PRODUCT, ITS ACCOMPANYING SOFTWARE, OR ITS
DOCUMENTATION. ALTUSEN SHALL NOT IN ANY WAY BE RESPONSIBLE FOR,
WITHOUT LIMITATION, LOSS OF DATA, LOSS OF PROFITS, DOWNTIME, GOODWILL,
DAMAGE OR REPLACEMENT OF EQUIPMENT OR PROPERTY, AND ANY EXPENSES
FROM RECOVERY, PROGRAMMING, AND REPRODUCTION OF ANY PROGRAM OR
DATA.
ALTUSEN makes no warranty or representation, expressed, implied, or statutory with respect to its products, contents or use of this documentation and all accompanying software, and specifically disclaims its quality, performance, merchantability, or fitness for any particular purpose.
ALTUSEN reserves the right to revise or update its product, software or documentation without obligation to notify any individual or entity of such revisions, or update.
For details about extended warranties, please contact one of our dedicated value added resellers.
93
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 11 Overview
- 12 Features
- 13 Requirements
- 13 Computer
- 13 KVM Over the NET™ Switch
- 13 Browsers
- 14 Licenses
- 14 Primary Servers
- 14 Secondary Servers
- 14 Archive Servers
- 14 Nodes
- 15 License Options
- 16 Add Node Options
- 17 Overview
- 17 Installing the VSR Software
- 17 Starting the Installation
- 19 Licenses
- 20 Overview
- 20 VSR Login
- 23 The VSR Main Page
- 23 Sessions
- 24 System Log
- 25 Settings
- 25 Server Type
- 26 Service Ports
- 26 Archive Server
- 26 Disable Keystroke Recording
- 27 Maintenance
- 27 Backup
- 27 Restore
- 28 License
- 28 Upgrading the License
- 29 Overview
- 29 Installing the VSR Archive Server
- 29 Starting the Installation
- 32 Licenses
- 33 Archive Server GUI
- 33 Setup
- 34 Playback
- 34 Begin Time/End Time
- 34 Search Filter
- 35 Play Selected
- 36 Export/Import
- 36 Begin Time/End Time
- 36 Device Name
- 37 Search File
- 37 Export File
- 37 Export & Delete
- 37 Delete File
- 37 Import File
- 38 Storage
- 39 Settings
- 40 License
- 41 Overview
- 41 Browser Login
- 42 The Web Browser Main Page
- 42 Page Components
- 43 The Tab Bar
- 45 Overview
- 45 Search Video
- 46 Port List
- 46 Playback
- 47 Advanced Search
- 47 Playback
- 48 Sessions
- 49 Video Log Viewer
- 49 Toolbar
- 53 Users
- 53 Adding Users
- 56 Modifying User Accounts
- 56 Deleting User Accounts
- 57 Groups
- 57 Creating Groups
- 58 Modifying Groups
- 59 Deleting Groups
- 60 Users and Groups
- 60 Assigning Users to a Group From the User’s Notebook
- 61 Removing Users From a Group From the User’s Notebook
- 62 Assigning Users to a Group From the Group’s Notebook
- 63 Removing Users From a Group From the Group’s Notebook
- 64 Device Assignment
- 64 Assigning Device Permissions From the User’s Notebook
- 65 Assigning Device Permissions From the Group’s Notebook
- 66 System Permissions
- 66 Assigning System Permissions From the User’s Notebook
- 67 Assigning System Permissions From the Group’s Notebook
- 68 Overview
- 68 Recording KVM Ports
- 69 Adding KVM Devices
- 70 Configuring KVM Ports
- 71 Deleting KVM Devices
- 72 Overview
- 72 Latest Logs
- 73 Search Logs
- 75 Notification Settings
- 76 Overview
- 77 System Info
- 77 VSR-Local
- 78 Network
- 79 Event Destination
- 81 Authentication
- 84 Security
- 84 Login Failures
- 85 Filter
- 87 Account Policy
- 88 Private Certificate
- 89 Certificate Signing Request
- 91 Video Session Recorder
- 91 Adding Secondary VSR Servers
- 92 Deleting Secondary VSR Servers
- 92 Enable/Disable Secondary VSR Servers
- 92 Maximum Recording Time
- 93 Log Servers
- 94 Overview
- 96 Safety Instructions
- 96 General
- 98 Technical Support
- 98 International
- 98 North America
- 99 USB Authentication Key Specifications
- 99 Supported KVM Over the NET™ Switches
- 100 Windows XP Installation
- 101 Trusted Certificates
- 101 Overview
- 102 Self-Signed Private Certificates
- 102 Examples
- 102 Importing the Files
- 103 Limited Warranty