advertisement
▼
Scroll to page 2
of 20
English USER'S MANUAL DMX MENU Please read before use UP DOWN ESC Contents Features 1 General Instructions 2 1. Overview 3 1.1 Front View 3 1.2 Rear View 5 2. Operation Guide 7 2.1 Display and standby mode 7 2.2 Set-up Menus 8 2.2.1 DMX fail 8 2.2.2 Phase Correction 9 2.2.3 DMX Address 10 2.2.4 Preheat 11 2.2.5 Curve 13 2.2.6 Preset 14 Technical Specifications 16 Improvement and changes to specifications, design and this manual, may be made at any time without prior notice. All Rights Reserved. Features Thank you for your purchase. This product features include: 12 DMX channel Individual DMX address / Block address Individual channel dimmer / Master dimmer Each channel can be programmed with the DMX address, and the preheat of the lamps(0-50%). Any of 12 chase programs can be recalled as required, chase speed is adjustable Chase programs 1-12, DMX Hold, Analogue can be selectable in the event DMX fails. Phase correction leads to linear dimming(0-100%). Control curve can be selectable from Linear/Switch/Square. Analogue input works even without any adjustment The short circuit protection for each channel with the use of 10A circuit breaker LCD Display Power failure memory 1 General Instructions Please read through this operating instructions before installing or using your new product. After you have finished reading the instructions, put them away in a safe place for future reference. WARNING! This product must be earthed. To prevent fire or shock hazard, do not expose this product under high temperature or moisture area. Do not make any inflammable liquids, water or metal objects enter the unit. No user serviceable parts inside, do not attempt repairs. Should you product fail, contact your local dealer. CAUTION! This product is intended for indoor use only. Provide occasional ventilation during use. Disconnect the power when not use for extended period. Do not use the unit in places subject to excessive humidity, vibration or bumps. Do not dismantle or modify the unit. 2 1. Overview 1.1 Front View 1 DMX MENU 7 Channel dimmer module 3 UP DOWN ESC 3 4 56 2 1. Overview 1.1 Front View 1. 2x16 LCD Display Shows the current activities or adjustments of menus. 2. DMX LED This LED blinks when DMX signal is present. 3. MENU Button This button is used to access set-up menus. 4. UP Button Tap this button to scroll through menus or to increase values . 5. DOWN Button Tap this button to scroll through menus or to decrease values . 6. ESC Button Tap this button to go back last menu level or to leave menu system. 7. Channel Dimmer Module(x12) The channel dimmer module is incorporated with a 10A circuit breaker and SCRs with 1000A peak current capacity. The removable, plug & play module enables easy and flexible setup of 12 channel module. 4 1. Overview 1.2 Rear View 9 1 Analog in: 0~10VDC 15 8 1 2 3 2 DMX IN 1 : Ground 2 : Data 3 : Data + DMX OUT 3 3 2 23-001-1518 1. Analogue Input DC 0-10V 2. DMX Input This jack is used to receive an incoming DMX signal.. 3. DMX Output This jack is used to send DMX signal to next DMX device or link to another unit. 5 1. Overview 1.3 Mains power & Output Termination 6 2. Operation Guide 2.1 Display and standby mode Power on this unit, the LCD shows the revision of software immediately, then enter standby mode automatically, the LCD shows the dimming level of each channel as below. The first row indicates the dimming level, and the second row indicates the channel(1 stands for channel 1, 2 stands for channel 2, and so on. A, B and C stand for channel 10, 11 and 12.). 1 2 3 4 5 6 7 8 9 ABC 2.2 Set-up Menus In standby mode, tap MENU button to enter set-up menus . There are 6 menus: DMX Fail, Phase Correction, DMX Address, Preheat, curve and Preset , you can use UP/DOWN button to scroll through the menus. Tap ESC button to leave set-up menus system. Dmx fail MENU UP DOWN ESC 2.2.1 DMX Fail Dmx fail 1. Tap UP/DOWN button to scroll to DMX Fail menu. MENU 7 UP DOWN ESC 2. Operation Guide 2.2.1 DMX Fail 2. Tap MENU button again to enter sub-menu system. You can use UP/DOWN button to select Hold/Analog/Prog. 1-12. [Hold]: Last received DMX signal is held. [Analog]: The analogue input(0-10v) is activated. [Prog. 1-12]: Starts internal programs 1-12. Dmx fail Hold MENU Dmx fail Analog 3. If you select Hold or Analog, you can tap ESC button to exit. MENU UP DOWN ESC Speed 00.4s 4. If you select Prog. 1-12, tap ESC button, speed menu will be activated. You can select the chasing speed from 0.1 to 20 seconds using UP/DOWN button. UP DOWN ESC MENU UP DOWN ESC Speed 02.4s MENU UP DOWN ESC After you've finished your setting, tap ESC button to exit. 8 2. Operation Guide 2.2.2 Phase Correction Pha corr 1. Tap UP/DOWN button to scroll to Phase Correction menu. MENU 2. Tap MENU button to enter sub-menu system. You can use UP/DOWN button to select Yes/No. [Yes]: Linear dimming is activated. [No]: Non-linear dimming is activated. UP DOWN ESC Pha corr Yes MENU 3. Tap ESC button to exit. UP DOWN ESC Pha corr Yes MENU UP DOWN ESC 2.2.3 DMX Address Dmx addr 1. Tap UP/DOWN button to scroll to DMX Address menu. MENU 9 UP DOWN ESC 2. Operation Guide 2.2.3 DMX Address 2. Tap MENU button to enter sub-menu system. You can use UP/DOWN button to select Block/Single. Dmx addr Block [Block]: Complete dimmer(6 channels) has only one start address. [Single]: The DMX address of each channel is selectable, several channels can select the same DMX addresses. MENU UP DOWN ESC 3. Tap UP/DOWN button to scroll to Block/Single menu, and tap MENU to enter Block/Single mode. Dmx addr Block MENU UP DOWN ESC + Start [001] MENU UP DOWN ESC Start [001] 4. In Block mode, you can use UP/DOWN button to select the start address from [001-512]. MENU UP DOWN ESC 10 2. Operation Guide 2.2.3 DMX Address Chan[1] [001] 5. In Single mode, tap MENU to change between the channel and its address. MENU 6. When channel is activated, tap UP/DOWN button to select from [1-12]; when address is activated, tap UP/DOWN button to select from[001-512]. UP DOWN ESC Chan[1] [001] MENU UP DOWN ESC Dmx addr 7. Tap ESC button to exit. MENU UP DOWN ESC 2.2.4 Preheat Preheat 1. Tap UP/DOWN button to scroll to Preheat menu. MENU 11 UP DOWN ESC 2. Operation Guide 2.2.4 Preheat 2. Tap MENU button to enter sub-menu system. Preheat All MENU UP DOWN ESC 3. Tap UP/DOWN button to select between All/Single mode, and tap MENU to enter All/Single mode. Preheat All MENU UP DOWN ESC + All [000%] MENU UP DOWN ESC 4. In All mode, tap UP/DOWM to select preheat value of all channels between 000%-050%. All [000%] MENU 5. In Single mode, tap MENU to select between channel and preheat value. UP DOWN ESC Chan[1] [000%] MENU UP DOWN ESC 12 2. Operation Guide 2.2.4 Preheat 6. When channel is activated, tap UP/DOWN button to select from [1-12]; when preheat is activated, tap UP/DOWN button to select from [000%-050%]. Chan[1] [050%] MENU UP DOWN ESC Preheat 7. Tap ESC button to exit. MENU UP DOWN ESC 2.2.5 Curve Curve 1. Tap UP/DOWN button to scroll to Curve menu. MENU 2. Tap MENU button to enter sub-menu system. Curve Linear MENU 13 UP DOWN ESC UP DOWN ESC 2. Operation Guide 2.2.5 Curve Curve Linear 3. Tap UP/DOWM button to select from Linear/ Switch/Square. MENU UP DOWN ESC Curve 4. Tap ESC button to exit. MENU 5. You can tap ESC button to return to Beginning Menu. UP DOWN ESC 1 2 3 4 5 6 7 8 9 ABC MENU UP DOWN ESC 2.2.6 Preset This menu allows you to control the dimmer of all channels or individual channel. Preset 1. Tap UP/DOWN button to scroll to Preset menu. MENU UP DOWN ESC 14 2. Operation Guide 2.2.6 Preset 2. Tap MENU button to enter sub-menu system. Preset All MENU UP DOWN ESC 3. Tap UP/DOWN button to select between All/Single mode, and tap MENU to enter All/Single mode. Preset All MENU UP DOWN ESC + All [000%] MENU UP DOWN ESC 4. In All mode, tap UP/DOWM to adjust the master dimming level from 000%-100%. All [000%] MENU 5. In Single mode, tap MENU to change between the channel and its dimming level. Chan[1] [000%] MENU 15 UP DOWN ESC UP DOWN ESC 2. Operation Guide 2.2.6 Preset 6. When channel is activated, tap UP/DOWN button to select from [1-12]; when dimming level is activated, tap UP/DOWN button to select from [000%-100%]. Chan[1] [050%] MENU UP DOWN ESC Preset 7. Tap ESC button to exit. MENU UP DOWN ESC Technical Specifications Power Input ......................................................... AC 120V~50/60Hz Channel Output(Single phase).......................... 10A/CH., Total 120A Channel Output(Three phases)................................ 10A/CH., 3x40A DMX Output ............................................... 3 pin female XLR socket DMX Input ..................................................... 3 pin male XLR socket Analogue Input ................................... 0-10V, 15-pin sub DIN socket Dimensions ............................................................ 482x390x160mm Weight(appro.) ...................................................................... 20.8 Kg 16 Printed in PR China Rev 1.0 October 2002 All Rights Reserved 24-004-0892
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project