NSE8 NSE12 Installation manual


Add to my manuals
68 Pages

advertisement

NSE8 NSE12 Installation manual | Manualzz

Installation Manual

Simrad NSE8 and NSE12

Multi-function Displays

English

www.simrad-yachting.com

A brand by Navico - Leader in Marine Electronics

Preface

Disclaimer

As Navico is continuously improving this product, we retain the right to make changes to the product at any time which may not be reflected in this version of the manual. Please contact your nearest distributor if you require any further assistance.

It is the owner’s sole responsibility to install and use the instrument and transducers in a manner that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing safe boating practices.

NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND AFFILIATES DISCLAIM

ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS,

DAMAGE OR THAT MAY VIOLATE THE LAW.

Governing Language: This statement, any instruction manuals, user guides and other information relating to the product (Documentation) may be translated to, or has been translated from, another language (Translation). In the event of any conflict between any

Translation of the Documentation, the English language version of the Documentation will be the official version of the Documentation.

This manual represents the product as at the time of printing. Navico Holding AS and its subsidiaries, branches and affiliates reserve the right to make changes to specifications without notice.

Copyright

Copyright © 2009 Navico Holding AS.

Feedback from you

Your feedback is important and helps Navico ensure that this manual is a valuable resource for all marine technicians. E-mail your comments or suggestions about this manual to the following address: [email protected]

Warranty

The warranty card is supplied as a separate document.

It is shipped with the product registration card.

In case of any queries, refer to the brand web site of your display or system.

www.simrad-yachting.com

| 1

2 |

Declaration of Conformity

GB

Hereby, Navico Holding AS declares that this NSE8, NSE12 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

FI

Navico Holding AS vakuuttaa täten että NSE8, NSE12 tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

NL

Hierbij verklaart Navico Holding AS dat het toestel NSE8, NSE12 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

FR

Par la présente, Navico Holding AS déclare que ce NSE8, NSE12 est conforme aux exigences essentielles et aux autres dispositions de la directive 1999/5/CE qui lui sont applicables.

SE

Härmed intygar Navico Holding AS att denna NSE8, NSE12 står i

överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

DK

Undertegnede Navico Holding AS erklærer herved, at følgende udstyr NSE8, NSE12 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/ EF.

DE

GR

Hiermit erklärt Navico Holding AS, dass sich dieses NSE8, NSE12 in

Übereinstimmung mit den grundlegenden Anforderungen und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG befi ndet.

(BMWi)

Με την παρουσα Navico Holding AS δηλωνει οτι NSE8, NSE12

συμμορφωνεται προς τις ουσιωδεις απαιτησεις και τις λοιπες σχετικες

διαταξεις της οδηγιας 1999/5/ΕΚ.

IT

Con la presente Navico Holding AS dichiara che questo NSE8, NSE12

è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

ES

Por medio de la presente Navico Holding AS declara que el NSE8,

NSE12cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

PT

Navico Holding AS declara que este NSE8, NSE12está conforme com os requisitos essenciais e outras provisões da Directiva 1999/5/CE.

The equipment named in this declaration, is intended for use in international waters as well as coastal sea areas administered by countries of the E.U. and E.E.A. A full

Declaration can be obtained from www.www.simrad-yachting.com

Disposal

Waste Electrical and Electronic Equipment (WEEE)

The use of the WEEE Symbol indicates that this product may not be treated as household waste. By ensuring this product is disposed of correctly, you will help protect the environment.

For more detailed information about the recycling of this product, please contact your local authority, your household waste disposal service provider or the shop where you purchased the product.

Contents

Introduction ...........................................................................................6

About this manual .................................................................................. 6

Conventions .......................................................................................... 6

Important safety and warning information ................................................. 6

Check the parts ..................................................................................... 7

Overview ................................................................................................8

Installing the display ............................................................................ 10

Mounting location ................................................................................. 10

Panel mount ........................................................................................ 11

Bracket Mount ..................................................................................... 12

System architecture .............................................................................14

Networking, Data Interfacing ................................................................. 14

SimNet / NMEA 2000 ......................................................................... 14

Ethernet: (NETWORK ports) ................................................................ 14

NMEA0183 ........................................................................................ 14

Data Bridging .................................................................................... 15

Wiring the NSE .....................................................................................22

Power ................................................................................................. 23

Connecting power .............................................................................. 23

Power control .................................................................................... 23

No Power Control ........................................................................................... 24

Auto Power on ............................................................................................... 24

Power Control Master ..................................................................................... 24

External alarm ..................................................................................... 26

SimNet ............................................................................................... 27

SimNet: The basics ............................................................................ 27

Planning and installing a SimNet backbone ............................................ 28

Power the SimNet network .................................................................. 28

Ethernet ............................................................................................. 31

Dual and Multi Station ........................................................................ 32

NMEA0183 wiring ................................................................................. 33

Video In .............................................................................................. 34

Video Out ........................................................................................... 35

Connecting BR24 Radar ....................................................................... 36

Connecting HD Radar ........................................................................... 37

Connecting BSM1 Broadband Echosounder .............................................. 38

| 3

4 |

Commission the system ........................................................................39

Turning on the system for the fi rst time .................................................. 39

Operating the menu system .................................................................. 39

Commissioning checklist ....................................................................... 40

System settings menu ........................................................................ 41

Language ......................................................................................... 41

Time: Local Time, Time format, Date Format ......................................... 41

Power Control ................................................................................... 41

Echosounder setup ............................................................................... 42

Depth offset .................................................................................................. 42

Water speed calibration .................................................................................. 42

Echo sounder software version ........................................................................ 42

Water speed averaging ................................................................................... 43

Temperature calibration .................................................................................. 43

Transducer type ............................................................................................. 43

Radar setup ........................................................................................ 43

Radar software version ................................................................................... 43

Radar Transmit, Standby or off ........................................................................44

Data setup .......................................................................................... 45

SimNet / NMEA2000 setup .................................................................. 45

Source selection (Auto select) ............................................................. 45

Source selection (Manual) .................................................................. 45

Group Source Selection (SIMRAD) .................................................................... 45

Group Source Selection (NONE) ....................................................................... 46

Source selection advanced .............................................................................. 46

Damping .......................................................................................... 48

Device List ........................................................................................ 48

Serial port setup .................................................................................. 49

NMEA 0183 output ............................................................................. 49

Fuel ................................................................................................... 50

Vessel Setup ..................................................................................... 50

AIS own vessel .................................................................................... 50

Diagnostics ......................................................................................... 51

NMEA2000 Diagnostics ....................................................................... 51

USER Database UDB .......................................................................... 51

Check GPS signal ................................................................................. 52

System backup .................................................................................... 52

Restore a backup ............................................................................... 52

Software upgrades ............................................................................... 53

Displaying current software version ..................................................... 53

NSE Display software version .......................................................................... 53

Ethernet module software version .................................................................... 53

Additional NSE display upgrade steps ...............................................................54

Screen capture .................................................................................... 55

File transfer ........................................................................................ 55

Drawings ..............................................................................................56

NSE8 Dimensions ................................................................................. 56

NSE12 Dimensions ............................................................................... 57

Spare parts ...........................................................................................59

NSE Spare parts .................................................................................. 59

Compatible BSM-1 Transducers ............................................................ 60

SimNet accessories ............................................................................ 60

Ethernet cables (yellow) ..................................................................... 61

Ethernet cables (RJ45) ....................................................................... 61

Repeat screens.................................................................................. 61

Video cables for repeat screens ........................................................... 61

Specifi cations .......................................................................................62

Supported NMEA0183 sentences ............................................................ 63

NMEA 2000 PGN List ............................................................................ 64

NMEA 2000 PGN Receive .................................................................... 64

NMEA2000 PGN Transmit .................................................................... 65

| 5

6 | Introduction

Introduction

About this manual

This manual is a reference guide for installing the Simrad NSE8 and NSE12 Multi Function

Display.

The information in this manual at the time of printing is correct to the best of our knowledge. Navico can not be liable for any inaccuracies or missing information.

Due to the constant improvement of Navico’s products. Navico cannot be liable for changes between the product and the manual. Refer to www.simrad-yachting.com for the latest manuals and addendums.

Conventions

Used when it is necessary to warn personnel that a risk of damage to the equipment or injury/death exists if care is not exercised.

Used to draw the reader’s attention to a comment or some important information.

Important safety and warning information

Please read carefully before use.

When navigating the vessel, use the Simrad NSE system only as a navigational aid. Proper navigation of the vessel is the sole responsibility of the vessel operator.

The electronic chart used by the NSE System is an aid to navigation only and is designed to supplement, not replace, offi cial government charts. Only offi cial government charts supplemented by notices to mariners contain the information required for safe and prudent navigation. Always supplement the electronic information provided by the Simrad NSE with other plotting sources such as observations, depth soundings, radar and hand compass bearings.

Should the information not agree, the discrepancy must be resolved before proceeding any further.

Never operate the NSE in Simulate Mode while you are underway. It is the user’s responsibility to ensure that Simulate Mode is used only in safe situations such as when you are moored in a marina.

The Global Positioning System (GPS) is operated by the US Government which is solely responsible for its operation, accuracy and maintenance. The GPS system is subject to changes which could affect the accuracy and performance of all

GPS equipment anywhere in the world.

The accuracy of the Echosounder depth display can be limited by many factors, including the type of transducer, the location of the transducer, and water conditions. Ensure that the transducer is installed correctly and the

Echosounder is used correctly.

Check the parts

NSE8

8.4 “ Display unit

PN location specifi c

NSE12

12 “ Display unit

PN location specifi c

NSE8 Dust cover

000-00134-001

Packaged parts list

NSE8 Bezel

000-00132-001

NSE12 Bezel

000-00133-001

NSE8 Gasket

NSE12 Dust cover

000-00135-001

NSE12 Gasket

NSE8 Mounting bracket

000-00136-001

NSE12 Mounting bracket

000-00137-001

NSE8 Cut-out Template

988-0175-05

NSE12 Cut-out

Template

988-0175-06

NSE8, NSE12

Video-In / Comms

Cable

000-00129-001

NSE8, NSE12

Installation Manual

988-0175_03

NSE8, NSE12

Quick start guide

988-0175-04

5 mm (0.20”) CLEARANCE HOLE TO SUIT M4 MACHINE SCREW

OR DRILL PILOT HOLE TO SUIT SELF TAPPING SCREW

CUTOUT

265 mm (10.40”)

Check dimensions before cutting

PRODUCT OUTLINE

NX50

25 mm (1.00”)

265 mm (10.40”)

285 mm (11.20)

NSE8, NSE12

Bracket knobs

000-00138-001

NSE8, NSE12

2 x Ratchet washers

072-2559-001

NSE8, NSE12

Power cable

000-00128-001

NSE8, NSE12

Connector Caps

000-00130-001

NSE8, NSE12

Operation manual

988-0175-02

NSE8, NSE12

Cleaning cloth

MS000682A-G

NSE8, NSE12

5 x SCREW,14G x

1,PAN POZI,S/T,SS

316,BLACK

SimNet Starter Kit: Includes

• 24005845 SimNet 5 m (16.5 ft) cable

• 24006298 SimNet 7-Prong Multi-Joiner

• 24005894 SimNet Termination Plug

• 24005902 SimNet 2 m (6 ft) power cable w/terminator

NSE8, NSE12

4 x SCREW,

8Gx1, PAN POZI,

S/T,16,LO-HEAD

Introduction | 7

8 | Overview

Overview

2 3 4

5

8

10

12

CHART RADAR ECHO NAV INFO PAGES

MENU

IN

WIN

OUT

1

MOB

4

GHI

2

ABC

5

JKL

7

PQRS

STBY

AUTO

8

TUV

0

3

DEF

6

MNO

9

WXYZ

PWR

1

11

13

16

6

7

9

15

14

13

2

3

4

5

6

7

8

9

10

Key

1

11

12

13

14

Description

Direct Access Keys (DAK). Provide direct access to a page. Repeated presses of each DAK cycles through several different pages that relate to the DAK

PLOT/MARK key. A short press activates the Plot menu, a long press positions a waypoint at the vessel position

Rotary knob. The function of the knob is depending on active context

GOTO/VESSEL key. A short press activates the Goto menu, a long press centers the chart to vessel position

3

key — Activates/confi rms current selection

X key cancels changes and returns to previous menu level

Cursor keypad used to move the cursor on the display, and to maneuver in the menu system

MENU key. Used to display the context menu for the active panel/overlay, and for selecting options in edit mode. . 2 x MENU for system settings menu

WIN key, used on multiple panels pages. A short press toggles between the panels, a long press expands active panel to a full page panel and back again

Zoom buttons for radar, echosounder and chart pages

Alpha numeric keypad used for entering numbers and text in dialog boxes.

A long press on the “1” key will position a Man Over Board (MOB) waypoint at the vessel’s current position

STBY AUTO - Future use

Media port door. Press and slide to the right to open.

Media can be used for optional Navionics chart data, software updates, transfer of user data and system backup

SD /MMC media card slot.

16 Removable bezel

4

1 2 3 5 6

Key

1

2

3

4

5

6

Description

Power. For power input 12 or 24 V DC input (see power page 23), Power control (see Power Control page 23) and external alarm (see External Alarm page 26).

Video In. Supplied cable provides two composite video inputs (see Video In page 34) and one RS422 port (NMEA0183 TX, RX) see NMEA0183 Wiring page 33

SimNet. Connects NSE display to a SimNet or NMEA2000 network (see

SimNet page 27).

Video Out. Connect to an external monitor via optional DVI cable (see Video

Out page 35).

Network 1, 2 and 3. Three Ethernet network ports for connecting to other NSE displays and Network modules. (see Ethernet on page 31)

USB. Used for Software updates, chart data base updates, backing up waypoints routes and tracks. A better option to the front port if it is exposed to the weather.

Note. A Water proof optional USB cable is available to extend this port to a dry location. (AA010078 USB dash mount)

Overview | 9

Installing the display

Mounting location

Choose the mounting locations carefully before you drill or cut. The display should be mounted so that the operator can easily use the controls and clearly see the display screen. Be sure to leave a direct path for all of the cables. The display screen is highcontrast and anti-reflective, and is viewable in direct sunlight, but for best results install the display out of direct sunlight. The chosen location should have minimal glare from windows or bright objects.

Ensure that any holes cut are in a safe position and will not weaken the boat’s structure.

If in doubt, consult a qualified boat builder.

At least 100 mm (4”) away from the compass, at least 300 mm (12”) away from any radio transmitter and at least 1.2 m (4 ft) away from any antenna.

Before cutting a hole in a panel, make sure that there are no hidden electrical wires or other parts behind the panel.

Do not mount any part where it can be used as a hand hold, where it might be submerged, or where it will interfere with the operation, launching or retrieving of the boat.

If bracket mounting chose a flat area where the display will not be subjected to excessive vibration.

Leave sufficient clearance space behind the display to connect all relevant cables.

Good ventilation is required behind the mounting panel. Poor ventilation may cause the display to overheat. The display is designed to operate in temperatures from -15° C to

+55° C (+5° F to +131° F).

For overall width and height requirements, please see the drawings at the back of this manual.

10 | Installing the display

Panel mount

5 mm (0.20”)

CLEARANCE HOLE TO SUIT M4 MACHINE SCREW

OR DRILL PILOT HOLE TO SUIT SELF TAPPING SCREW

CUTOUT

265 mm (10.40”)

Check dimensions before cutting

PRODUCT OUTLINE

NSE-8

25 mm (1.00”)

265 mm (10.40”)

285 mm (11.20)

1

Attach the fl ush mounting template to the selected mounting position using adhesive tape.

2

Drill pilot holes for the four hole saw cuts and four self tapping screws used to secure the display. If using

M4 machine screws use a 5 mm

(0.20 ”) drill bit.

A

3

Use a 25mm (1 “) hole saw to cut the four corner radius

4

Cut along the dotted line and remove the shaded area.

5

6

7

8

Peel backing off the gasket and apply to the surface.

Connect all cables to the rear of the unit before placing the unit into the console.

Secure the display to the surface

To fi nish off the installation fi rmly clip the front bezel in place

Installing the display | 11

Bracket Mount

An alternative to flush mounting the NSE8 or NSE12 is to bracket mount the unit. This method has the advantage that the display can easily be removed when not in use. The display may be tilted for best possible viewing angle when bracket mounted.

1

Press the ratchet washers into the bracket.

2

Loosely screw securing knobs to the

Display unit.

12 | Installing the display

3

Temporarily mount the display unit in the bracket and make sure the display can be adjusted to the correct angle without interfering with the surrounding. Allow space for cables attached to the rear of the unit.

4

Remove the display unit and use the mounting bracket as a template to mark the fi ve positions of the screw holes.

5

Drill a pilot hole for the fi ve screws and an optional hole large enough for the cables to emerge from.

6

Secure 5 the bracket to the surface

7

8

Connect the cables.

Slide the display into the mounting bracket and secure in place with the bracket knobs.

9

Attach the bezel. Firmly clip the front bezel in place.

NSE Bezel removal

B

C

A

Protect the dash area adjacent to the top edge (or bottom edge) of the display.

Apply upwards pressure on the bezel (A), this will create an opening between the bezel and the case. Insert a medium size fl at blade screw driver into the gap (B) Slide the screw driver along the gap to release the clips along the top. Continue down the side until the bezel releases. The same routine can be applied to the bottom edge if accessible.

Installing the display | 13

14 | System architecture

System architecture

This section explains how the NSE connects to other devices as part of a system. The

NSE has a highly scalable system architecture. A system can consist of a basic stand alone chart plotter, or expand to a networked, multi-display system connected to a wide range of accessories.

The system architecture is modular with a wide range of peripherals and accessories that can be connected to SimNet or NMEA2000 devices such as instrument systems,

AIS, GPS and heading sensor to Ethernet devices such as Radar and Echosounder. For multi display installations the system can be set up to be truly masterless, i.e. have no dependency on other displays being powered on.

A NSE display can connect to other devices in the system by Ethernet, SimNet /

NMEA2000 or NMEA0183.

A system can have:

• between one and six displays, The displays can be any mix of NSE8 and NSE12

• one radar only

• one echosounder only

Networking, Data Interfacing

The NSE system can use three data networks. SimNet (NMEA2000), Ethernet and

NMEA0183.

SimNet / NMEA 2000

SimNet is Simrad’s proprietary CAN bus network for transfer of navigation data such as wind, Position, AIS, etc between all SimNet or NMEA2000 devices on a SimNet/

NMEA2000 network.

SimNet is lower bandwidth than the Ethernet network, but is 50 times faster than

NMEA0183

Ethernet: (NETWORK ports)

NSE uses an Ethernet network for the transfer of high bandwidth data between other

NSE displays and from network modules such as Radar, Echosounder and Weather module

Each NSE display has three Ethernet network ports. An optional 5 port expansion port is available. (Recommended for multiple NSE displays)

Ethernet does not transfer navigation data such as position, heading etc. This is handled either by SimNet and or NMEA 0183. However navigation and display settings are synchronized over Ethernet

NMEA0183

NMEA0183 is a point to point connection. Each NSE display has one NMEA0183 port using RS422 protocol. Each display can output to one NMEA0183 “Listener” and receive from one NMEA0183 “Talker”.

Data Bridging

Supported NMEA0183 sentences entering the system are bridged (converted) to

SimNet/NMEA2000 and distributed on the SimNet backbone for all other displays to use

Certain SimNet /NMEA2000 PGNs (messages/sentences) are bridged across to

NMEA0183 to be available as an output from any NSE display

Ethernet to SimNet. Limited data is bridged from the Ethernet echosounder. Speed, depth and temperature are bridged to SimNet and NMEA0183. Depth, speed and temperature data from the echosounder is the only data bridged from Ethernet

DISPLAY 1

DISPLAY 2

0183

B

CHART RADAR ECHO NAV INFO PAGES

GPS

MENU WIN

OUT

MOB

RANGE IN

MOB

1

4 GHI

7 PQRS

STBY

AUTO

2 ABC

5 JKL

8 TUV

0

3 DEF

6 MNO

9 WXYZ

PWR

PLOT

MARK

GO TO

VESSEL

NMEA0183

MENU WIN

RANGE

1

4 GHI

7 PQRS

STBY

AUTO

2 ABC

5 JKL

8 TUV

0

PWR

3 DEF

6 MNO

CHART RADAR ECHO NAV INFO PAGES

Heading

RX RX +

NMEA0183 Talker

A

SimNet Network SimNet Network

TX TX +

NMEA0183 Listner

C

A

B

C

Example of data bridging

In this example a NMEA0183 (talker) is connected to DISPLAY 1

The NMEA sentences are bridged across to SimNet and distributed on the

SimNet network

The NMEA0183 listener connected to DISPLAY 2 can receive the NMEA0183 sentences from the device connected to DISPLAY 1 and also from other devices that are on the SimNet network

An NMEA talker can be connected to each NSE display and both set of data will be converted to SimNet. Each display can be setup for outputting selected NMEA sentences.

Speed, temp and depth data from the echosounder transducer that is to be displayed as an instrument has to bridged from ethernet to SimNet. A NSE display has to be nominated to bridge the data. If this nominated display is turned off, no data will be displayed, until the display is turned on or another display is selected to bridge the data

(see Source Selection on page 45).

NMEA0183 to SimNet bridging only applies to the NMEA0183 sentences outlined in the

Supported NMEA0183 Sentences section of this manual (see page 62).

System architecture | 15

Single station confi guration possibilities

POWER

12 or 24 V DC

Black

Red (FUSE)

Yellow

Blue

+_

Power Control

Ext. Alarm

Supplied with display or accessory

Power cable

Optional accessory

NSE Display

VIDEO OUT

DI15

From

NSE12

DI10

From

NSE8

Simrad DI10 or DI15 display’s

Note: NSE8 only connects to DI10

NSE12 only connects to DI15

OR

MO19

From

NSE12 or NSE8

MO19 or third party DVI

Monitor

Note dimming not controlled by NSE

VIDEO /DATA

Video 2 (Green)

Composite Video

Green

Orange

Video 1 (Red)

NMEA 0183

Serial port

1 x RS422 port

NMEA 0183

RX +

RX -

Yellow

Blue

TX +

TX -

Video In / Data cable

+_

12 v DC

T

SIMNET

SimNet starter kit

Power cable w/term

Drop cable 2 m (6 ft)

Termiator plug

7 way joiner

ECHOSOUNDER

T

SIMNET NETWORK

SimNet devices

GPS

AIS

Instuments

Autopilot

Heading

Depth

Engines

NMEA2000

Amp for

USA Only

Audio cable

Pulse Radar

2,4,6,10 or 25 kW

Sirius satelite weather and radio

WEATHER

USA Only

RADAR

Ethernet RJ45 2m (6.5 ft)

BR24 Broadband Radar

OR

BSM1 Broadband

Echo Sounder

16 | System architecture

Supplied with display or accessory

Optional accessory

Video In / Data

Video 2

Video 1

Cameras

NMEA 0183

RX +

RX -

Green

Orange

Dual station confi guration possibilities

VIDEO OUT

DVI Video Cable

Video 2

Video 1

Video In / Data

DI15

From

NSE12

DI10

From

NSE8

Simrad DI10 or DI15 display’s

Note: NSE8 only connects to DI10

NSE12 only connects to DI15

OR

NMEA 0183

RX +

RX -

MO19

From

NSE12 or NSE8

TX +

TX -

Yellow

Blue

TX +

TX -

MO19 or third party DVI

Monitor

Note dimming not controlled by NSE

NSE8 or NSE12

NSE8 or NSE12

Ethernet Ethernet

SimNet Starter kit

Power cable w/term

Drop cable 2 m (6 ft)

Termiator plug

7 way joiner

T

SIMNET

T

GPS

Instuments

Autopilot

Heading

Depth

Engines

AIS

NMEA2000

SIMNET

Ethernet 5 Pin 2m (6.5 ft)

RADAR

OR

RADAR

WEATHER

USA Only

Ethernet RJ45 2m (6.5 ft)

ECHOSOUNDER

Ethernet 5 Pin 2m (6.5 ft)

BR24 Broadband Radar

Pulse Radar

2,4,6,10 or 25 kW

System architecture | 17

18 | System architecture

RX +

RX -

TX -

TX +

NMEA0183 Out

SimNet power 12 V DC (with terminator)

DVI Cable

SimNet power 12 V DC (y

System architecture | 19

20 | System architecture

RX +

RX -

TX -

TX +

SimNet power 12 V DC (with terminator)

DVI Cable

SimNet power 12 V DC Must be y

System architecture | 21

22 | Wiring the NSE

Wiring the NSE

Wiring guidelines

Most installation problems are caused by shortcuts taken with system cables. When wiring the NSE, follow the guidelines below.

Don’t do this

Don’t make sharp bends in the cables

Don’t run cables in a way that allows water to fl ow down into the connectors

Don’t route the data cables in areas adjacent to radar, transmitter, or large current carrying cables

Do this

Do make drip and service loops

Do tie-wrap all cables to keep them secure

If cables are shortened, lengthened, or reterminated, do seal and protect all wiring connections

Do leave room at the back to install and remove cables

Before starting the installation, be sure to turn electrical power off. If power is left on or turned on during the installation, fi re, electrical shock, or other serious injury may occur. Be sure that the voltage of the power supply is compatible with the NSE display

The NSE has a voltage rating of 12 V DC or 24 V DC. (9 V DC - 32 V DC max range). SimNet is 12 V DC only

The red wire should always be connected to (+) DC V using a fuse or thermal breaker (10 Amp)

Power

The NSE8 and NSE12 displays can be powered by either 12 V or 24 V DC. Displays are protected against reverse polarity, under voltage and over voltage.

The supplied power cable has a four core cable used for:-

• power into the system (Red and Black wires) controling power state of the display or power state of other displays and devices

(Yellow wire)

• connecting to an external alarm (Blue wire)

1 4

2 3

Power Cable (000-00129-001)

2 m (6.5 ft)

Con.

2

3

4

Pin Wire color

1

Function

Black Battery (-)

Blue

Red

External Alarm

Yellow Power control

Battery (+)

12 - 24 V DC

Connecting power

The red wire should always be connected to (+) DC V using a fuse or thermal breaker (10 Amp)

Power control

The yellow (Power Control) wire can either be an input that will turn on the display when power is applied, or an output that turns on other devices when the display is powered on. It can be configured at the installation stage to control the power state of displays and compatible devices. Planning is required how you want to be able to turn on and off compatible devices. When commissioning the system, displays can be set to be a Power

Control Slave or Power Control Master.

Power Control configuration options are:-

Use the Power button to turn on the display only: Yellow wire not connected

Display to turn on when power is applied to the display: Common red and yellow wires

Use the Power button to turn on the display and other displays and or compatible devices such as BR24 Radar: Yellow wire connected to a Power Control Bus. (Set one or more displays to be a Power Control Master)

Wiring the NSE | 23

Black

Red (FUSE)

Yellow

Blue

+ _

No Connect

12 - 24 V DC

No Power Control

Display will turn on and off when the power button on the front of the unit is pressed. Power Control wire is not attached

Power Control Master

Black

Red (FUSE)

Yellow

Blue

+ _

12 - 24 V DC

Auto Power on

Display will turn on when power is applied to the display. Common the yellow wire with the red wire after the fuse.

Note: The unit can not be powered down but can enter a standby mode.

Power Control Slave

A B

24 | Wiring the NSE

C

Black

Red

Yellow

Black

Red

Yellow

BR24 Radar

Black

Red

Yellow

+ _

12 - 24 V DC

Power Control Bus

Power Control Master

Display (A) turns on using the power button. It is set as the Power Control Master and will output voltage on the Power Control bus to turn on display (B) and BR24 Radar

(C). Display (B) is set to Power Control Slave and if turned on by display (A) cannot be powered down using its power button, but can be set to standby. If display (A) is off, display (B) can be turned on using its power button, but won’t turn on any other devices. Display (B) could, however also be set to Power Control Master.

Power control table

Can turn on by own PWR button

Can turn off by own PWR button

Can turn on other devices

Can be turned on or off by another device

Can turn off entire system if started by an ignition switch

Can have more than one on a system

* If Power control wire is not connected.

YES *

YES *

NO

YES

NO

YES

Slave

YES

YES

YES

YES

NO

YES

Master

If a display has its power state controlled by another display or ignition switch, it can’t be totally powered down. It can enter a standby state to save power. If the power button is pressed and Power Off selected, a message will appear “Preparing to standby…”

To confi gure a display as a Power Control Slave or Master please refer to the Power

Control Setup on page 41.

Wiring the NSE | 25

26 | Wiring the NSE

External alarm

An external alarm can be connected to one or more displays on the network. The external alarm can be a small peizo buzzer connected directly or a horn siren connected via a relay.

Alarms are configured globally in the system i.e they can be configured on one display and seen, heard and acknowledged from all displays. How ever the external alarm siren can be enabled or disabled on individual displays. For information on configuring alarms refer to the Alarms section in the Operation manual

9 x2

MENU WIN

Black

Red (FUSE)

Yellow

Blue

1 A max

35 V DC max

+ _

12 - 24 V DC

For sirens that draw more than 1 Amp use a relay

12 - 24 V DC

Black

Red (FUSE)

Yellow

Blue

+ _

SimNet

SimNet is a data network based on NMEA2000 CAN bus technology that makes interconnection and integration of Simrad and NMEA2000 products simple. SimNet permits the exchange of data between the interfaced products and enables the flow of commands and instructions between the various SimNet and NMEA2000 compatible products. The data transfer capability of SimNet is 50 times higher than the NMEA0183 standard at 4800 baud.

The advanced SimNet Plug & Play (P&P) function provides flexibility and automatic interface setup to Simrad products. Previous models of Simrad products that are not

SimNet compatible and non-Simrad products also benefit from this P&P setup function.

Certain NMEA0183 data can be converted to and from the SimNet network by;

• connecting directly to the NMEA0183 port on an NSE Display using and optional converter unit such as the AT10 connecting to a device that has the built-in capability to convert NMEA0183 to SimNet

/ NME2000

Most NMEA2000 devices can be connected directly to a SimNet backbone and SimNet devices can be connected to a NMEA2000 network by using adapter cables. (see SimNet

cables list on page 60)

SimNet connector

1

5

4

2

3

1

2

3

4

5

Pin Function

CAN_H

SimNet power (+) 12 V DC

SimNet power (-)

Shield

CAN_L

SimNet: The basics

SimNet is Simrad’s proprietary data network based on NMEA2000 CAN bus.

SimNet is a powered network. It must have a separate 12-15 V DC power supply protected by a 5 Amp fuse. Do not connect the SimNet power cable to the same terminals as the start batteries, Autopilot Computer, Radar, thruster or other high current products.

A SimNet network consists of a linear “backbone” from which “drop cables” to SimNet devices connect. Devices that have more than one SimNet connector can be part of a

SimNet backbone (daisy chained) (But not as part of a NMEA2000 backbone).

A drop cable is a SimNet cable that connects a SimNet device to the backbone. A drop cable has a maximum length of 6 m (20 ft).

A SimNet Network has a maximum cable length of 120 m (394 ft), which includes drop cables + 30 m (98.5 ft) mast cable. Total 150 m (500 ft) max.

-

-

a terminator plug (red cap) terminated in-line joiner (red locking collars) a wind transducer (terminator is in the mast head unit as opposed to mast cable).

Wiring the NSE | 27

28 | Wiring the NSE

Certain Simrad products have two SimNet connectors, which can be made to be part of the backbone. This daisy chaining cannot be part of a NMEA2000 backbone

Menu Menu

-

meet the CE, FCC regulations with a SimNet adapter cable do not exceed the SimNet load specification (please refer to separate document

Simrad SimNet Installation Manual (20222006)

Planning and installing a SimNet backbone

Plan the SimNet backbone carefully

For part numbers refer to SimNet Accessories page 59

The SimNet backbone needs to run between the locations of all SimNet products you want to install, and be less than a 5.5 m (18 ft) cable run from a SimNet device.

Choose from the following components to make up your SimNet backbone

SimNet cables: 0.3 m (1 ft), 2 m (6,6 ft), 5 m (16.6 ft), and 10 m (33 ft) cables

SimNet power cables with or without termination

SimNet in-line joiner with or without termination

T-Joiner. Use at locations where you want to connect a single SimNet device or join lengths of SimNet cable

7 way joiner. Use to connect up to 5 devices at one location

Wind transducer. If using a wind sensor, plan to connect this to one end of the backbone as this has a terminator built in

Power the SimNet network

A SimNet network requires its own 12 V DC power supply protected by a 5 amp fuse or breaker. For 24 V use a DC-DC converter

Connect power at one end of the backbone for smaller systems using a SimNet power cable with termination (red cap).

For larger systems introduce power at central point in the backbone to “balance” the voltage drop of the network. Use SimNet cable without termination (yellow cap)

(24005910) (See system drawings following)

If joining to an existing NMEA2000 network or similar CAN bus network that has it’s own power supply, do not connect to another power supply.

Do not connect the SimNet power cable to the same terminals as the start batteries,

Autopilot Computer, Radar, thruster or other high current products

The drawing below shows a small SimNet network. Power is introduced at one end using a SimNet power cable with termination ending with a second terminator.

F

-

12 V DC

+

A B C D

T

E

T

T

SimNet drop cable

SimNet power

SimNet terminator

A slightly larger system below. Power is connected at one end using terminated power cable. A second terminator is required at the end of the backbone.

F

T

SimNet drop cable

SimNet backbone

SimNet power

SimNet terminator

_

12 V DC

+

A B C D

T

E

M enu

G

M enu

H

T

D

E

F

G

H

A

B

C

Key Description

SimNet power source. Stable 12 V DC only

5 Amp fuse or breaker

Switch

SimNet power cable with termination (red disc) (24005902)

SimNet 7 way joiner

SimNet or NMEA 2000 GPS antenna

SimNet backbone daisy chained using instruments with two SimNet ports.

SimNet backbone

Wiring the NSE | 29

30 | Wiring the NSE

For a large systems or sailboats with a mast head wind sensor and long mast cable, it is recommended to use a SimNet noise filter (24006934). On sail boats the filter should be inserted at the mast junction. On larger systems without a mast head unit, the filter should be inserted centrally along the backbone.

G

T

M enu M enu

_

+

12 V DC

A B C D

F

E

F

F

H

M enu

T

F

G

E

SimNet drop cable

SimNet backbone

SimNet power cable

C

D

E

A

B

F

G

H

Key Description

SimNet power source. Stable 12 V DC only

5 Amp fuse or breaker

Switch

SimNet power cable without termination (yellow disc) (24005910)

SimNet 7 way joiner

SimNet 3 way joiner

Terminator

Noise Filter

Ethernet

The NSE system uses an Ethernet network to interconnect high bandwidth devices such as other NSE displays, radar and echo sounder. Each NSE display has three network ports with 5 pin connectors. Ethernet network cables have orange connectors that are retained by a bayonet type locking collar.

If more than three network devices need to be connected, use the optional network expansion Port.

For multi-station systems it is recommended to use a network expansion port to join two or more displays. Connecting this way removes the dependency of another display being powered on that may have an Ethernet device connected, such as a radar

Ethernet connector

Pin

1

2

3

4

5

1

5 4

2

3

Function

TX +

TX -

RX +

RX -

GND

Single Station

Broadband Sounder ™

Broadband Radar™

Wiring the NSE | 31

Dual and Multi Station

If there is more than one display it is recommended to use a network expansion port

NETWORK

Network Expansion Port

POWER NETWORK

Broadband Radar™

Broadband Sounder™

Alternatively you can connect two or more NSE displays without an network expansion port. However, this will mean any display with a device connected by Ethernet will need to be powered on for other NSE displays to use the device.

DISPLAY A DISPLAY B

32 | Wiring the NSE

Broadband Sounder™

Broadband Radar™

Display (A) must always be on to enable radar and echo sounder data transfer to

DISPLAY (B)

Connecting to Navico HD Radar / Older Sirius Weather module

(RJ45 Ethernet connectors)

A B

Ethernet Adapter cable yellow 5 pin to

Navico RJ45 cable. refer Ethernet Cables

(yellow) page 60.

Navico RJ45 Ethernet cable.

Refer to Ethernet Cables (RJ45) page

60 for part numbers.

NMEA0183 wiring

To exchange NME0183 data, the NSE8 and NSE12 display units have a NMEA0183 communication port.

The port uses RS422 protocol and can be configured in the software for different baud rates. NMEA sentences can be turned on or off. See Serial Port Setup, page 49

Refer to Supported NMEA0183 sentences on page 62 for a complete list of sentences

VIDEO IN

RS422

A

B

Key

C

6

5

8

7

Pin Color

Red

Green

Orange

Green

Yellow

Blue

+

+

-

A

B

RX -

RX +

TX -

TX +

TX -

TX +

RX -

RX +

Cable color description

Video in port 1

Video in port 2

RS422 RX -

RS422 RX +

RS422 TX +

RS422 TX -

2

3

1

8

7

6

5

4

6

7

8

3

4

5

Pin

1

2

Function

Video 1 Ground

Video 1 (+)

Video 2 Ground

Video 2 (+)

RS422 TX -

RS422 TX +

RS422 RX +

Rs422 RX -

NMEA0183 Talker

NMEA0183 Listner

Cable Connector

C

Wiring the NSE | 33

34 | Wiring the NSE

Video In

Connect up to two composite video cameras to each display unit using the supplied Video

/ Data cable. This connects to the VIDEO IN port on the rear of the display. Video inputs are only displayed locally and are not distributed to other displays. Only one video input can be viewed at a time. Video inputs can be cycled.

Video In Connector

VIDEO IN

VIDEO 1

VIDEO 2

2

3

1 7

8

6

5

4

4

5

6

7

8

Pin

1

2

3

Function

Video 1 Ground

Video 1 (+)

Video 2 Ground

Video 2 (+)

RS422 TX -

RS422 TX +

RS422 RX -

Rs422 RX +

Video In / Data Cable (000-00129-001)

+

-

A

B

C

A

B

Key

C

Color

Red

Green

Orange

Green

Yellow

Blue

Video in port 1

Video in port 2

RS422 RX -

RS422 RX +

RS422 TX +

RS422 TX -

Description

Video Out

The NSE display has a DVI-I Video connector. Connect a second display to replicate what is on the screen of the NSE display.

A DI10 display can only interface to NSE8 and DI15 only to NSE12 due to fixed resolutions.

The MO19 or other scalable monitor or TV can be connected to either NSE8 and NSE12

MO19

Or third party monitor

From NSE8 or NSE12

(scales to resoloution)

B

VIDEO OUT

DI15

From NSE12 only

(1024x768)

A

DI10

From NSE8 only

(800x600)

Video-Out cable part numbers (Optional)

A

Key

B

Part Number

AA010152

AA010154

AA010162

AA010164

AA010157

3 m (9.8 ft) Video cable DVI-HD26 for DI10/DI15

DI15 displays

Description

10 m (33 ft) Video cable DVI-HD26 for DI10/DI15

5 m (16.5 ft) HDMI small connector option for DI10 or

15 m (50 ft) HDMI small connector option for DI10 or

DI15 displays

5 m DVI -DVI video cable for MO19 monitor

Wiring the NSE | 35

Connecting BR24 Radar

SimNet

Network

Scanner cable

A

Power

I

H

G

F

D

E

F

G

J

H

C

B

36 | Wiring the NSE

G

H

I

J

A

B

C

D

E

Key

F

+_

White RX+

Brown RX-

TX+

TX-

AT10HD

NMEA083 to SimNet

Converter Heading Only

Cut off 12 Pin plug to expose bare wires

NMEA0183 10 Hz Heading

(e.g Gyro, Sat Compass)

Alternative: NMEA0183 heading

Description

NSE Display.

BR24 BroadBand™ Radar system for NSE. Includes parts C,D and E.

Scanner cable. 20 m (65 ft) : Optional 10 m (33 ft) and 30 m (98 ft).

RI10 Radar interface box.

Ethernet cable. BR24 comes with a 2 m (6.5 ft) 5 pin cable. The BR24 can be connected directly to NSE or via a Network Expansion Port see page 32 for more information. See Ethernet cables yellow on page 60 for more cable length options.

SimNet Drop Cables: The BR24 and NSE are connected to the SimNet backbone

BR24 uses heading at 10 hz to calculate MARPA. (Not included)

Power cable. (see Power section on page 23). Always use a fuse or breaker.

SimNet backbone. Refer to SimNet section on page 27.

Power control bus: In this case BR24 is connected to Power Control Bus. BR24 is turned on when the NSE is powered on.

For MARPA and chart overlay use a heading sensor.

Either a SimNet / NMEA2000 heading sensor such as the RC42. Or if a

NMEA0183 10 hz heading sensor is installed, convert to SimNet using a AT10HD or connect to the NMEA in port on a NSE. Refer NMEA0183 Wiring page 33

Connecting HD Radar

2 kW 12 V DC ONLY

4 kW & 6 kW 12 or 24 V DC

10 kW & 25 kW 24 V DC ONLY Scanner

D

Ethernet

AT10HD

A

B

D

C

F

E

H

I

H

K

G

AA010070

K

J

+_

TX+

TX-

NMEA0183 10 Hz Heading

(e.g Gyro, Sat Compass)

RX+ White

RX- Brown

AT10HD cable(cut off plug)

RX- White

RX+ Black/White

AA010070 Utility cable

C

E

I

J

K

A

B

Key

F

G

H

Alternative: NMEA0183 heading

Description

NSE Display.

HD radar system for NSE. Includes parts C,D and E. 2kw & 4 kW Radome.

6 kW, 10 kw and 25 kW open array

Scanner cable. 20 m (65 ft) .

Ethernet cable RJ45 (male/male). Available in 2,5 and 10 m, (6.5, 16.5 & 33 ft)

For cable options see Ethernet Cables RJ45 on page 60

Ethernet Adapter cable. Yellow 5 pin (Male) to RJ45 (female) 2 m (6 ft). The HD radar can be connected directly to NSE or via a Network Expansion Port see page 32 for more information. See Ethernet cables (yellow) on page 60 for more cable length options.

AT10HD: SimNet to NMEA0183 converter (Heading only @ 10 Hz). Provides heading to the radar processor for MARPA calculations

SimNet backbone. For more information refer to the SimNet section on page

27.

SimNet drop cable.

SimNet heading sensor RC42

Power cable. Make sure a fuse is used. See Radar installation manual for fuse size. Note voltage requirements are model dependant

Wiring the NSE | 37

Connecting BSM1 Broadband Echosounder

A

F

3

4

2

7

5

1

6

B

C

B

E

D

38 | Wiring the NSE

+_

A

B

C

Key

D

E

F

Pin 1 Depth +

Pin 2 Speed

Pin 3 Speed power

Pin 4 Temp

Pin 5

Pin 6

Depth -

Shield

Pin 7 Temp / speed ground

Description

NSE display

BSM-1 Broadband Echosounder module

Ethernet cable yellow 5 pin see Ethernet cables yellow on page 60 for more cable length options. Cable can be connected directly to NSE or via a Network

Expansion Port see Ethernet page 32

12 or 24 V DC

Transducer: See compatible transducer list on page 59

Transducer Connector

Commission the system

Turning on the system for the fi rst time

Before starting the system for the first time, check the following;

Check radar is physically clear to rotate

Leave a HD pulse radar in standby for 30 minutes before transmitting for the first time

Check all personnel are clear of radar beam (HD Radar)

Check all wiring is correctly connected. Apply power to the breaker

To turn ON the display, press and release the PWR key.

To place display in to Standby, press PWR key and select stand by.

To turn OFF the display, press and hold PWR key for three seconds.

If you turn the unit ON when no external equipment is connected you will be asked to run in simulator mode.

Operating the menu system

In this manual you will see few direct text references to keys, menus and menu entries, and few step-by-step descriptions. By using graphics we will guide you to the key and the required menu selections.

In the illustrations throughout the commissioning section the following symbols are used:

Single short press on illustrated key

MENU WIN

3 s

MENU WIN

Press and hold on illustrated key with time indication x2

MENU WIN

Press twice on illustrated key

Rotate rotary knob

Single short press on rotary knob

PLOT

MARK

GO TO

VESSEL

PLOT

MARK

GO TO

VESSEL

References to keys on the operator panel are written in boldface, e.g. WIN key.

For further information on the operating the system refer to the Operation Manual

Commission the system | 39

Commissioning checklist

The NSE has a number of advanced features which can be configured through the settings menu.

It is recommend you become familiar with the operation of the unit using the default settings before making any changes to these menus.

Settings menus will vary depending on the optional sensors and devices attached.

Before changing system settings make sure that all displays are powered on as a lot of settings are global and are shared across the Ethernet network.

It is recommended to note the original settings before making adjustments or changes.

NSE related check list

System

Set Language

Set Units

Set time

Set Time and Date format

Set power control option if used. Repeat on all relevant displays

Data sources

Perform auto source selection

Perform any manual source set up

Set NMEA0183 baud rate and output sentences. Settings relevant to displays with NMEA0183 devices attached.

Set up of SimNet groups for parameters such as dimming and alarms

Set up SimNet source selection groups as needed or leave as default. Default is all parameters are set to SIMRAD group

Any custom setup of devices such as renaming sources. Source select advanced

Calibrate any dock side devices e.g SimNet depth offset

Confi rm Auto pilot interface

Echosounder

Set transducer type

Set depth offset

Sea temperature calibration

Speed calibration

Water speed averaging

Radar

Set antenna height: HD and Broadband Radar

Set zero bearing: HD and Broadband Radar (note, perform heading sensor calibration fi rst

Set zero range (main bang): HD Radar

Adjust for local interference: Broadband Radar

Park angle: Open array HD Radar

Heading sensor calibration

AIS

Enter own ships MMSI number

Back up settings

Create a backup of the display settings and transfer to portable drive or SD card

Refer

Page

41

41

41

41

46

43

42

43

42

43

50

52

45

45

49

47

47

43

43

43

43

43

43

40 | Commission the system

System settings menu

To access the system settings menu press

9 x2

MENU WIN

Language

Language used on menus and dialog boxes

Step 1

PLOT

MARK

GOTO

VESSEL

Choose

Language

Step 2

PLOT

MARK

GOTO

VESSEL

Select

Language

Step 3

PLOT

MARK

GOTO

VESSEL

Yes to restart

Notes

The display will need to be restarted for change to take effect

Time: Local Time, Time format, Date Format

Step 1 Step 2 Step 3 Notes

PLOT

MARK

GOTO

VESSEL

Choose

Local time

Local time (Time Offset) against GMT from the GPS.

Default is GMT

MENU WIN

To time fomat or save

MENU WIN

Highlight

Time format

PLOT

MARK

GOTO

VESSEL

Choose

Time format

MENU WIN

Highlight Date format

PLOT

MARK

GOTO

VESSEL

Choose Date format

12 or 24 hour time values

Default is 12 hour

MENU WIN

To date format or Save

Save

Or

Cancel

Day/Month/Year

Month/Day/Year

Power Control

If the system has been wired to use the yellow power control wire, it is necessary to make each display either a power control Slave or power control Master. Refer to Power

Control section on page 23.

Step 1 Step 2 Step 3 Notes

PLOT

MARK

GOTO

VESSEL PLOT

MARK

GOTO

VESSEL

Choose

Power control mode

Select Power

Control mode

Commission the system | 41

Echosounder setup

Depth offset

Is a value that can be entered to make the depth on the Echo page represent either depth below the transducer or depth below the surface.

A) Depth below Keel value: Is the distance from transducer to the keel:

Enter a negative value.

B) Depth Below Transducer: no offset required.

C) Depth Below Surface (waterline) value: Is the distance from transducer to the surface:

Enter a positive value.

A B C

Water speed calibration

Water speed off set

Water speed calibration is used to adjust the speed value from the paddle wheel to match the actual speed.

This can be measured either from the GPS speed over ground (SOG) or by timing the boat over a known distance. Water speed calibration should be performed with as little wind and current movement as possible.

Select Auto correct to match water speed to ground speed

Manual calculation. If in average the water speed reads

8.5 knots and SOG records 10 knots. Increase the offset to 117%. The calculation is:

Difference in speed

Paddle wheel speed x 100.

If water speed is lower than SOG then increase the calibration value.

Calibration range is 10-400 % Default is 100 %

Echo sounder software version

Software version are displayed under Sonar installation. To upgrade Sonar software refer to Software upgrades on page 53

42 | Commission the system

Water speed averaging

Averages water speed by measuring your speed at a selected interval of time. Water speed intervals range from one to thirty seconds. If you select five seconds, your water speed will be recorded every five seconds, then averaged.

Calibration range: 1-30 seconds. Default is 1 second.

Temperature calibration

Temperature calibration is used to adjust the water temperature value from the echo sounder transducer to match the data from another temperature sensor.

Calibration range: -9.9° - +9.9°. Default is 0°.

Transducer type

Transducer type is used for selecting the transducer model connected to the echo sounder module. In some transducers with built-in temperature sensors, the temperature may not be correct if the correct transducer is not selected from the transducer type menu.

See compatible transducer list on page 59

Note: Other depth sources will have their own calibration

Radar setup

Basic set up is required on all new radar installations. The set up varies slightly between

Boradband radar and the range of conventional HD pulse radars. The NSE will detect the type of radar and display relevant information.

Broadband Radar™

To commission a

BR24 Radar:

• set bearing alignment set antenna height local interference rejection (if needed)

HD Pulse Radar

To commission a pulse radar;

• set bearing alignment set antenna height. set range offset

Park angle for open array scanners

HD Pulse Radars: Leave in standby for 30 min before transmitting. (First time only) to burn in the magnetron.

Radar software version

Radar type and software version are displayed under radar installation. To upgrade radar software refer to Software Upgrades on page 53.

Commission the system | 43

Radar Transmit,

Standby or off

Press Radar function button to display the radar

9

MENU WIN

Press Menu to bring up radar options

To make radar adjustments.

• select item to adjust

PLOT

MARK

GOTO

VESSEL

Adjust the setting value as needed

Setting value is displayed on screen

Range Offset

9

MENU WIN

To confi rm

Broadband Radar™

Interference from some onboard sources can interfere with the

Broadband radar. One symptom of this could be a large target on the screen that remains in the same relative bearing even if the vessel changes direction.

Choose from Local interference rejection Low, Med or high.

Default is off

HD Pulse Radar

The timing of the transmit and receive circuits can be adjusted to determine zero range.

Position the vessel stationary about 150-200 m from a straight jetty or sea wall. Set the radar to 1/8 nm. If the sea wall appears bent or bowed adjust until the wall appears straight

All Radars

This will compensate for any physical misalignment of the scanner in relation to the center line of the vessel Set the radar to transmit. Point the boat in the direction of a stationary objet such as a pier or the end of a head land or peninsular. Adjust the bearing alignment so the heading line touches the end of the same head land or peninsular.

Set the radar scanner height. The Radar uses this value to calculate sea clutter

44 | Commission the system

Data setup

Data set up is required on initial start up of the system, or if any part of the SimNet or

NMEA 2000 network has been changed or replaced.

From Network in the main system settings menu you can

Select SimNet / NMEA2000 data sources either automatically or manually

Configure SimNet / NMEA2000 devices

Control how device parameters such as backlighting, units and damping are grouped on the network

Share waypoints via SimNet or NMEA2000

Monitor and diagnose both Ethernet and SimNet Networks

Setup NMEA0183 port, baud rate and output data

Control damping

SimNet / NMEA2000 setup

Source selection (Auto select)

SimNet Plug and Play offers easy and uncomplicated interfacing to data sources with automatic system setup.

The Auto Select option will look for all sources connected to the NSE system. If more than one source is available for each data type, the NSE will automatically select from an internal SimNet priority list.

Make sure all devices are connected and are turned on

Step 1 Step 2 Step 3 Step 4

PLOT

MARK

GOTO

VESSEL

Choose

Auto Select

PLOT

MARK

GOTO

VESSEL

Start Auto

Select

PLOT

MARK

GOTO

VESSEL

Select OK when fi nished

Source selection (Manual)

Devices can be selected manually to be the preferred source. This is useful if you have more than one of the same type of device on the network e.g. two GPS antennas.

It is also useful if you prefer that one display is to get position from one GPS antenna and another display to get position from another GPS antenna.

Group Source Selection (SIMRAD)

SimNet products such as the NSE, IS20 or AP24 have the ability to;

• use data sources that all other products on the network use, or use a data source independently from other units.

globally change all displays over to a different source from any display. (This will only include products set to Simrad Group mode.)

When configuring data sources on an NSE display you can select or change a source used by all the displays on the SimNet network, this is called group source selection.

For example you can select to change the position source globally on all displays that are in a source selection group.

There is only one source selection group available and this is group is called Simrad.

Commission the system | 45

There are ten categories of sources such as Compass, Navigation, Position etc. Under each of these categories a display can be set to receive data from sources as part of the

Simrad group or receive the source data independently from the group (None)

The example below shows the available options for position sources, and that the GS15

GPS is used by all displays with group selection set to Simrad. If you selected the GS10 all displays in the Simrad group would use the GS10 GPS.

Group Source Selection (NONE)

You may prefer one display to receive its position information from the GS10 antenna independently from the rest of the displays in the source selection group Simrad.

Set the position information to None.

PLOT

MARK

GOTO

VESSEL

Select None

PLOT

MARK

GOTO

VESSEL

Select the GS10 antenna

PLOT

MARK

GOTO

VESSEL

Under the position category, change group selection from

Simrad to None

9

MENU WIN to confi rm and exit

Source selection advanced

Allows the selection of a source not using Simrad group - eg Engine and Tank sources.

46 | Commission the system

SimNet Groups

The SimNet Group function is used to control parameter settings, either globally or in groups of units. It groups parameter settings such as backlighting, units and alarms.

The function is used on larger vessels where several units are connected via the SimNet network. By assigning several units to the same group, a parameter update on one unit will have the same effect on the rest of the group members.

The following example shows a two station installation. All four displays in the cockpit have their Display and Alarms in a different SimNet Group from the displays on the bridge. If a back light or alarm is adjusted on a display in the cockpit, it will change on all displays in the cockpit. It wont change the back light or alarms or displays on the bridge.

Bridge

NSE

CHART RADAR ECHO NAV INFO PAGES

PLOT

MARK

GO TO

VESSEL

MENU WIN

OUT

MOB

RANGE

MOB

IN

1

GHI

7PQRS

STBY

AUTO

0

2 ABC

5

8

JKL

TUV

3 DEF

6

9

MNO

WXYZ

PWR

NSE

CHART RADAR ECHO NAV INFO PAGES

PLOT

MARK

GO TO

VESSEL

OUT

MOB

MENU WIN

RANGE IN

MOB

1

4 GHI

7PQRS

STBY

AUTO

JKL

TUV

0 PWR

MNO

WXYZ

J1

J3

J2 J1

J3

J2

IS20

NSE

CHART RADAR ECHO NAV INFO PAGES

PLOT

MARK

GO TO

VESSEL

MENU WIN

OUT

MOB

1

RANGE

7PQRS

STBY

AUTO 0

MOB

IN

3

DEF

6 MNO

9 WXYZ

PWR

NSE

CHART RADAR ECHO NAV INFO PAGES

PLOT

MARK

GO TO

VESSEL

MENU WIN

OUT

MOB

1

4 GHI

7PQRS

STBY

AUTO

RANGE IN

MOB

2

ABC

5 JKL

8 TUV

0 PWR

J1

J3

J2 J1

J3

J2

IS20

Step 1

Cockpit

Step 2 Step 3

PLOT

MARK

GOTO

VESSEL

Choose the

SimNet Group

PLOT

MARK

GOTO

VESSEL

Select OK when fi nished

Notes

There are seven groups or none to choose from.

Default is Simrad

Select the SimNet

Group to be applied to the category

Commission the system | 47

Enter a logical name for the device such as a location to differentiate same devices e.g. GS15 Port

Damping

Controls how quickly instruments respond to changes in values from sensors.

Damping can be used for heading, wind, boat speed and depth instruments.

Increasing the damping applies more averaging or smoothing of the data update rate on the instrument or display. Damping settings are applied to SimNet displays and

Instruments belonging to particular damping SimNet Groups.

Device List

Using the Device List Function you can:

• list all of the active SimNet and NMEA2000 devices on the network, showing model description and serial number. Devices can be sorted by model ID or by serial number display information relating to a device such as, name, manufacturer, software version, instance, status give the device a logical name relevant to the user see data coming from the device

Some devices can be confi gured further

Device data can be viewed

48 | Commission the system

Serial port setup

Configure the serial port to match the NMEA0183 device that it is connected to.

Baud Rate (common for input and output)

Step 1 Step 2 Step 3

PLOT

MARK

GOTO

VESSEL

Rate

Select Baud

PLOT

MARK

GOTO

VESSEL

Select OK

NMEA 0183 output

Select the desired NMEA0183 sentences to be transmitted. (see Supported NMEA0183

sentences page 49).

Uncheck NMEA0183 output to turn off all sentences.

Output rate is shown.

Heading is output as fast as possible depending on band width

All NEMA0183 sentences are set to off when unit is shipped

Commission the system | 49

Fuel

If the vessel has an NMEA2000 interface to its engines and fuel tanks the NSE can display the following fuel consumption information:

Fuel used since last fill

Fuel used on current trip

Fuel used during the season

Calibration of the tanks is needed to display accurate fuel levels.

Vessel Setup

AIS own vessel

If an AIS system is installed. Enter the vessels MMSI number to prevent the own vessels

AIS icon being displayed on the chart

50 | Commission the system

Diagnostics

NMEA2000 Diagnostics

Bus State: Indicates if SimNet backbone is operating: Check power: Check termination

RX Overfl ows / Overruns greater than 0 could indicate the software is very busy and unable to keep up with incoming messages.

RX / TX Errors: CAN interface error counters.

Count up when there are errors on the CAN bus, and down when things are Ok. Should normally be

0. Goes bus off when 255 is reached. Check same things as for Bus state if greater than 0 observed.

Fast Packet Errors: Detected errors since power up. Check the network if this is continually increasing.

Rx / Tx Messages: A count since power up of messages received / transmitted.

USER Database UDB

The diagnostic page shows the MAC address of the display, the status and versions of the five user data bases.

The UDB (user database) is a database of all user created items and settings. Every time a change is made on a NSE display, the databases are synchronized so no one display holds all the user information. All displays should display the same version number for all databases.

The IP address of NSE displays that have had changes made to their settings are also shown.

Commission the system | 51

Check GPS signal

Press direct access key PAGES >3

System backup

A backup of all the NSE settings such as page layouts, custom instruments can be made at any time, and either stored on the NSE or transferred to a USB key or SD Card

Press direct access key PAGES > 9.

Name the backup using the alphanumeric key pad.

Press MENU select copy.

Restore a backup

To restore or import a backup,

Select the fi le, Press menu and select import. The system will perfom a restart for imported settings to take effect.

Select destination to copy fi le too.

52 | Commission the system

Software upgrades

Software upgrades can be performed on the following types of devices from any NSE display.

NSE displays

SimNet devices

Ethernet devices

The same procedure is used to upgrade software on all types of devices. Upgrade files for different types of devices have different file extensions.

NSE displays

xxx.xxx.xxx.UPD

Ethernet devices

device.RIW

SimNet / NMEA2000 devices

Device_x.x.xx.xx.swup (or .luf)

Displaying current software version

NSE Display software version

PLOT

MARK

GOTO

VESSEL

Software version is

25.31.32 Platform 1.0.0-r2

Ethernet module software version

Echo Sounder: On Echo page select Menu Radar: On Radar page select Menu

Software version :

CA1637C

Commission the system | 53

Example below shows upgrading a SimNet IS20 Combi instrument but is the same for

NSE displays

Menu Item

Copy upgrade fi les on to a USB Stick

Step 1

Press function button PAGES

Press 9 or navigate to fi les button

Step 2

Select Memory card

Step 3

Press Menu

9

MENU WIN

Select Upgrade

Select the upgrade fi le

Insert USB Stick into front or rear

USB ports

Additional NSE display upgrade steps

Do not interrupt power or remove the card, key in “01” when prompted after restart

Step 3 Continued

The NSE will list devices that can be ungraded by the selected software upgrade fi le.

Select the unit to be upgraded. (there is only one IS20 Combi on this network)

Step 4 Step 5

Select start upgrade Select OK to fi nish

After upgrading a display or Ethernet device please power cycle the entire system

54 | Commission the system

Screen capture

It is possible to capture a snap shot of the current screen

Step 1 Step 2

Enable screen capture

Step 3

1

MOB

2

4

GHI

5

ABC

JKL

3

DEF

6

MNO

7

PQRS

8

TUV

9

WXYZ

STBY

AUTO

0

PWR

Short press on PWR button to capture screen shot

File transfer

Step 1

Insert a USB Flash drive or SD card

Create desired screen to capture

Step 2

Press PAGES > 9

Browse to the desired screen shot to copy

Press MENU and select Copy select the USB Drive or SD card as the location to copy the fi le too.

Commission the system | 55

56 | Drawings

Drawings

NSE8 Dimensions

221.0 mm (8.70”)

212.0 mm (8.35”)

NSE12 Dimensions

273.0 mm (10.75”)

266.0 mm (10.47”)

Drawings | 57

58 | Spare parts

Spare parts

NSE Spare parts

Part Number

000-00132-001

000-00133-001

000-00134-001

000-00135-001

000-00136-001

000-00137-001

000-00138-001

000-00143-001

000-00139-001

000-00140-001

000-00128-001

000-00129-001

000-00130-001

000-00131-001

000-00141-001

Description

NSE8 Bezel with decal

NSE12 Bezel with decal

NSE8 Dust cover

NSE12 Dust cover

NSE8 Mounting bracket

NSE12 Mounting bracket

Mounting bracket knobs & washers (pair L/R)

Flush mount kit

Rotary knob

SD card door kit

Power cable

Video in / NMEA0183 comms cable

Connector caps

Documentation wallet

Installation manual

000-00142-001 Operators manual

NSE Optional accessories

Part Number

000-0125-25

24005829

Simrad GS15 GPS Antenna

Simrad GS10 GPS Antenna

BR24 Broadband Radar

Description

AA010220

Pulse radar

BR24 Broadband Radar for NSE

DX42S-1

DX64S-1

TX06S

TX010S

2kW 18 Inch Radome, radar processor and 15 m scanner cable

4 kW 24 Inch Radome, radar processor and 15 m scanner cable

6 kW 4 ft open array, radar processor and 20 m scanner cable

10 kW 6 ft open array, radar processor and 20 m scanner cable

TX025S 25 kW 7 ft open array, radar processor and 20 m scanner cable

BSM-1 Broadband Echosounder

000-0132-05 BSM1 Broadband Echosounder

Compatible BSM-1 Transducers

Part Number

000-0136-02

000-0136-03

000-0136-04

000-00021-001

000-0136-05

000-0136-06

000-0136-00

000-0106-82

000-0106-91

000-0106-77

000-0099-95

000-0099-93

000-0099-94

000-00022-001

Description

Airmar P319, plastic, low profi le, thru hull 50/200 KHz, depth/temp,

7 pin blue connector

Airmar P79, plastic, In-Hull 50/200 KHz, depth only, 7 pin blue connector

Airmar B60, bronze, low profi le, thru hull, 50/200 KHz, depth/ temp, 12° tilt, 7 pin blue connector

Airmar B60, bronze, low profi le, thru hull, 50/200 KHz, depth/ temp, 20° tilt, 7 pin blue connector

Airmar B744V, bronze, thru hull 50/200 KHz, depth/temp/speed, high-speed fairing block, 7 pin blue connector

Airmar B164, bronze, low profi le, thru hull, 1 kW 50/200 KHz, depth/temp, 12° tilt, 7 pin blue connector

Airmar B258, bronze, thru hull, 50/200KHz, depth/temp, highspeed fairing block, 7 pin blue connector

Airmar B260, bronze, thru hull, 50/200KHz, depth/temp, highspeed fairing block, 7 pin blue connector

Airmar M260, plastic In-hull, 50/200KHz, depth only, tank kit

HST - DFSBL 50/200 kHz transom-mount skimmer depth/temp

TS-1BL Temperature sensor (non-networked)

XT-12BL 3.65 m (12 ft) blue transducer extension cable

XT-20BL 6 m (20 ft) blue transducer extension cable

Cable, adapter, 6 Pin LTW to 7 Pin BLUE

SimNet accessories

Part Number

SIMKIT-1

SIMKIT-2

24005829

24005837

24005845

24005852

44172260

24005860

24006298

24006306

24005878

24005886

24005894

Description

SimNet Starter Kit: Includes

• 24005845 SimNet 5 m (16.5 ft) cable

• 24006298 SimNet 7-Prong Multi-Joiner

• 24005894 SimNet Termination Plug

• 24005902 SimNet 2 m (6 ft) power cable w/terminator

SimNet Starter Kit with one AT10 NMEA0183 interface

• 24005936 AT10 two way general NMEA0183 to SimNet Converter

• 24005837 SimNet 2m (6 ft) cable

• 24005845 SimNet 5m (16.5 ft) cable

• 24006298 SimNet 7 Prong Multi-joiner

• 24005894 SimNet termination plug

• 24005902 SimNet 2m (6 ft) power cable w/terminator

0.3 m (1 ft) SimNet cable

2 m (6.6 ft) SimNet cable

5 m (16.6 ft) SimNet cable

10 m (33 ft) SimNet cable

SimNet In-line joiner

SimNet T-joiner (3 prong)

SimNet Multijoiner (7 prong)

SimNet Bulkhead T-connector

SimNet cable gland

SimNet protection plug

SimNet termination plug

Spare parts | 59

60 | Spare parts

44172278

24005902

24005910

24005936

24005944

24005928

24005729

24006199

24006413

24006363

24006934

SimNet termination In-Line joiner

2 m (6.6 ft) SimNet power w/termination

2 m (6.6 ft) SimNet power w/o termination

AT10 Universal NMEA0183 converter

AT15 Active T-connector, IS15

SimNet cable protection cap

SimNet to Micro–C (male) cable that connects a SimNet product to a NMEA2000 network

SimNet to Micro-C (female) cable that connects a NMEA2000 product to SimNet

SimNet to Micro-C female to SimNet 4 m (13 ft)

SimNet cable, 5.5 m (18 ft), with 1 plug

SimNet noise fi lter

Ethernet cables (yellow)

Part Number

000-0127-55

000-0127-56

000-0127-51

000-0127-29

000-0127-30

000-0127-37

Description

Adapter cable: Ethernet Yellow to RJ45 adaptor 0.3m (1 ft)

Adapter cable: Ethernet Yellow male to RJ45 female 2 m (6.5 ft)

Ethernet cable yellow 5 Pin 2 m (6.5 ft)

Ethernet cable yellow 5 Pin 4.5 m (15 ft)

Ethernet cable yellow 5 Pin 7.7 m (25 ft)

Ethernet cable yellow 5 Pin 15.2 m (50 ft)

Ethernet cables (RJ45)

Part Number

AA010080

AA010081

AA010082

Description

Ethernet cable RJ45 2 m (6.6 ft)

Ethernet cable RJ45 5 m (16.5 ft)

Ethernet cable RJ45 10 m (33 ft)

Repeat screens

Part Number

000-0134-00

000-0134-01

26058578

Description

DI10 Display

DI15 Display

MO19B Monitor 19” Rear or bracket mount

Video cables for repeat screens

Part Number

AA010152

AA010154

AA010162

AA010164

AA010157

Description

3 m (9.8 ft) Video cable DVI-HD26

10m (33 ft) Video cable DVI-HD26

5 m (16.5 ft) HDMI small connector option for DI10 or DI15 displays

15 m (50 ft) HDMI small connector option for DI10 or DI15 displays

5 m DVI -DVI video cable for MO19 monitor

Specifi cations

Mechanical

Back Case Die cast aluminium

Heat Sinking Direct heat transfer from processor to casting

Screen Direct bonded, anti refl ective, LED backlit

Environmental

Operating temperature

-15° C to +55° C (+5° F to +131° F)

Waterproof integrity IPx7

Certifi cates of

Conformity

CE(EN60945:2002)/CTick

Electrical

Operating Voltage 12 or 24 V DC (9 - 34 V DC max)

Processor Via Eden ULV 1.6 GHz

RAM 512 MB

Hard drive 80 GB

User interface

User interface Direct access keys (DAK’s), alphanumeric keypad, rotary knob with push-to-Enter

Languages (31) English (UK), English (US), German, French, Spanish,

Italian, Portuguese, Croatian, Finnish, Icelandic, Dutch,

Norwegian, Polish, Swedish, Slovenian, Russian, Ukrainian,

Bulgarian, Asian language pack

Plotter Characteristics

Display modes Head-up*, Course-up, North-up (*external heading or COG)

Cartography Embedded: Navico Insight HD US/Navionics Platinum Rest of

World; Navionics Platinum Plus via SD Card

Latitude Limit 83º North, 85º South

Alarms Position, Off-Course, Waypoint Radius, Arrival, Anchor, Anchor

Depth, Shallow, Deep, Water Temp Rate, Low

Boat Speed, True Wind Shift, True Wind High, True Wind Low,

Guard Zone 1 & 2, Voltage Hi/Lo, Missing Data:

Depth/Rudder/Wind/Heading/Weather, Weather: Lightning,

Severe Weather, Storm, Weather Watchbox, Vessels:

Dangerous, AIS Lost, Message, MARPA Lost, MARPA

Unavailable, Autopilot Alarms

Radar Characteristics

Radar compatibility Broadband: Simrad BR24

Simrad HD Digital Series 2 kW to 25 kW

Display Modes Head-up, Course-up*, North-up*, Relative Motion (*Heading input required)

Echo Trails Intervals: 15 sec, 30 sec, 1 min, 3 min, Continuous. Clear

Trails

VRM/EBL 2: User confi gurable

Video In

Channels Two multiplexed

Format Composite

Standard Support for NTSC type N and 4.4.43, PAL type B, D,G,H, I,

M,N, Selected by user

Comms

NMEA0183 1 x RS422 port

Specifi cations | 61

62 | Specifi cations

Supported baud rates 4,800, 9,600, 19,200, 38,400 Note. Port will transmit and receive at the set baud rate

Max number of displays

Ethernet 10/100 base Ethernet, three ports

6 in any combination NSE8 or NSE12

External connectors

(front)

External Connectors

Display size

(rear) x 1 USB and x 1 SD

Power (power control, ext. alarm), Video-in (NMEA 0183/

Composite video x2), SimNet (NMEA2000), Network (3 x ethernet, USB x 1, Video Out (DVI-I x 1)

Display specifi c specifi cations

NSE8

8 “ Diagonal Display size

NSE12

12.1” Diagonal

Display resolution

Brightness (max)

Contrast ratio

800 x 600

1500 nits

850:1

Display resolution

Brightness

Contrast ratio

1024 x 768

1500

600:1

Viewing angle

Height

Width

Depth

Weight

Current Draw (in

Watts) at 12/24VDC

Display only

60 deg. above and below normal axis with: >75% nominal brightness >100:1 contrast ratio

60 deg. side to side about normal axis with: >75% nominal brightness >100:1 contrast ratio

212 mm (8.35")

285 mm (11.22")

Height

Width

266 mm (10.47”)

356 mm (14.01”)

111 mm (4.38")

3.2 kg (7 lb)

21.6W or 1.8A @

12.0 V DC / 21.6W or

0.9A @ 24VDC

Depth

Weight

Current Draw (in

Watts) at 12/24 VDC

Display only

122.7 mm (4.83”)

5.5 kg (11.5 lb)

33.6W or 2.8A

@ 12.0 V DC /

33.6W or 1.4A @

24VDC

Supported NMEA0183 sentences

TX / RX

Receive

Transmit

GGA

GGA

Receive

Transmit

Receive

Transmit

RMC

AAM

DBT

DBT

Receive

Transmit

Receive

Transmit

Receive

HDG

HDG

MWV

MWV

DSC

Transmit TLL

APB

DPT

DPT

HDT

GLL

GLL

GSA

GSA

GSV

GSV

GPS

VTG

VTG

Navigation

ZDA

ZDA

BOD

MTW

MTW

BWC BWR

VLW

VLW

Echo

VHW

VHW

Compass

HDM

RMC

Wind

RMB XTE

MWD

DSE

TTM

VDM

AIS / DSC

AIS sentences are not bridged to or from

SimNet.

MARPA

These are only out put sentences

NMEA 2000 PGN List

NMEA 2000 PGN Receive

60928 ISO Address Claim

60928 ISO Address Claim

126208 ISO Command Group Function

130312 Temperature

130313 Humidity

130576 Small Craft Status

127245 Rudder

127251 Rate of Turn

127257 Attitude

127488 Engine Parameters, Rapid Update

127489 Engine Parameters, Dynamic

127493 Transmission Parameters, Dynamic

65323 Data User Group Request

130840 Data User Group Configuration

130842 SimNet DSC Message

128259 Speed, Water referenced

128275 DistanceLog

129025 Position, Rapid Update

129026 COG & SOG, Rapid Update

129029 GNSS Position Data

129033 Time & Date

129038 AIS Class A Position Report

129039 AIS Class B Position Report

129040 AIS Class B Extended Position Report

129283 Cross Track Error

129540 GNSS Sats in View

129794 AIS Class A Static and Voyage Related

Data

129801 AIS Addressed Safety Related

Message

129802 AIS Safety Related Broadcast

Message

129808 DSC Call Information

130074 Route and WP Service - WP List - WP

Name & Position

65285 Temperature with Instance

65292 Clear Fluid Level Warnings

130831 Suzuki Engine and Storage Device

Config

130832 Fuel Used - High Reolution

130834 Engine and Tank Configuration

130835 SetEngineAndTankConfiguration

130838 Fluid Level Warning

130839 Pressure Insect Configuration

130843 Sonar Status, Frequency and DSP

Voltage

Specifi cations | 63

NMEA2000 PGN Transmit

126208 ISO Command Group Function

128259 Speed, Water referenced

128275 DistanceLog

129025 Position, Rapid Update

129026 COG & SOG, Rapid Update

129029 GNSS Position Data

129283 Cross Track Error

129540 GNSS Sats in View

130074 Route and WP Service - WP List - WP

Name & Position

130312 Temperature

130840 Data User Group Configuration

65287 Configure Temperature Insects

65289 Trim Tab Insect Calibration

65290 Paddle Wheel Speed Configuration

65292 Clear Fluid Level Warnings

130828 Set Serial Number

130831 Suzuki Engine and Storage Device

Config

130835 SetEngineAndTankConfiguration

130836 Fluid Level Insect Configuration

130837 Fuel Flow Turbine Configuration

130839 Pressure Insect Configuration

130845 “Weather and Fish Prediction and

Barometric Pressure History”

130850 Evinrude Engine Warnings

64 | Specifi cations

Specifi cations | 65

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents

Languages