D-Link DGS-3200-16 - Switch - Stackable Installation guide

Hardware
Installation Guide
Product Model: xStack ® DGS-3200 Series
Layer 2 Managed Gigabit Ethernet Switch
_____________________________________________
Information in this document is subject to change without notice.
© 2011 D-Link Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden.
Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are registered trademarks of Microsoft
Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. D-Link Corporation
disclaims any proprietary interest in trademarks and trade names other than its own.
June 2011 P/N 651GS3200045G
FCC Warning
This equipment has been tested and found to comply with th e limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this m anual, m ay cause harm ful interfe rence to ra dio communications. Operation of this e quipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference in which case the user may be
required to take adequate measures.
Warnung!
Dies ist ein Produkt der Klasse A. Im Wohnbereich kann dieses Produkt Funkstoerungen verursachen. In diesem Fall kann vom
Benutzer verlangt werden, angemessene Massnahmen zu ergreifen.
Precaución!
Este es un producto de Clase A. En un entorno doméstico, puede causar interferencias de radio, en cuyo case, puede requerirse al
usuario para que adopte las medidas adecuadas.
Attention!
Ceci est un produit de classe A. Dans un environnement domestique, ce produit pourrait causer des interférences radio, auquel cas
l`utilisateur devrait prendre les mesures adéquates.
Attenzione!
Il presente prodotto appartiene alla classe A. Se utilizzato in ambiente domestico il prodotto può causare interferenze radio, nel cui
caso è possibile che l`utente debba assumere provvedimenti adeguati.
VCCI Warning
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Table of Contents
Intended Readers........................................................................................................................................................................... vi
Typographical Conventions ...........................................................................................................................................................................vi
Notes, Notices, and Cautions ....................................................................................................................................................... vii
Safety Cautions ............................................................................................................................................................................................ vii
General Precautions for Rack-Mountable Products .................................................................................................................................... viii
Lithium Battery Precaution........................................................................................................................................................................x
Protecting Against Electrostatic Discharge .....................................................................................................................................................x
Introduction....................................................................................................................................................11
Switch Description........................................................................................................................................................................................11
Features....................................................................................................................................................................................................12
Ports.........................................................................................................................................................................................................14
Front-Panel Components .........................................................................................................................................................................15
LED Indicators..............................................................................................................................................................................................15
Rear Panel Description ............................................................................................................................................................................17
Side Panel Description.............................................................................................................................................................................18
Installation ......................................................................................................................................................19
Package Contents ..........................................................................................................................................................................................19
Installation Guidelines ..................................................................................................................................................................................19
Installing the Switch without a Rack .......................................................................................................................................................20
Attaching Brackets to a Switch for Rack Mounting.................................................................................................................................21
Mounting the Switch in a Standard 19" Rack ..........................................................................................................................................22
Installing the Switch on a Wall................................................................................................................................................................23
Power On ......................................................................................................................................................................................................24
Power Failure...........................................................................................................................................................................................24
Installing SFP Ports.......................................................................................................................................................................................25
Connect to RPS .............................................................................................................................................................................................26
External Redundant Power System ...............................................................................................................................................................27
DPS-900 ..................................................................................................................................................................................................27
DPS-800 ..................................................................................................................................................................................................28
Connecting the Switch ...................................................................................................................................29
Switch to End Node ......................................................................................................................................................................................29
Switch to Switch ...........................................................................................................................................................................................29
Connecting To Network Backbone or Server ...............................................................................................................................................30
Introduction to Switch Management ...........................................................................................................31
Management Options ....................................................................................................................................................................................31
Connecting the Console Port (RS-232 DCE/RJ-45)......................................................................................................................................32
Managing the Switch for the First Time .......................................................................................................................................................33
Password Protection......................................................................................................................................................................................34
SNMP Settings ........................................................................................................................................................................................35
IP Address Assignment............................................................................................................................................................................36
Web-based Switch Configuration.................................................................................................................38
iv
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Introduction.................................................................................................................................................................................. 38
Logging onto the Web Manager....................................................................................................................................................................38
Web-based User Interface .............................................................................................................................................................................39
Areas of the User Interface ......................................................................................................................................................................39
Web Pages.....................................................................................................................................................................................................40
Appendix A – Technical Specifications........................................................................................................41
Appendix B – Cables and Connectors..........................................................................................................43
Appendix C – Module Specs and Cable Lengths ........................................................................................44
Appendix D – Glossary..................................................................................................................................45
Appendix E – Warranties & Technical Support........................................................................................ 47
v
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Intended Readers
The DGS-3200 Series Hardware Installation Guide contains information for set up and management of the Switch. This manual
is intended for network managers familiar with network management concepts and terminology.
Typographical Conventions
Convention
Description
[]
In a command line, square brackets indicate an optional entry. For example: [copy
filename] means that optionally you can type copy followed by the name of the file. Do
not type the brackets.
Bold font
Indicates a button, a toolbar icon, menu, or menu item. For example: Open the File
menu and choose Cancel. Used for emphasis. May also indicate system messages or
prompts appearing on screen. For example: You have mail. Bold font is also used to
represent filenames, program names and commands. For example: use the copy
command.
Boldface
Font
Typewriter
Indicates commands and responses to prompts that must be typed exactly as printed in
the manual.
Initial capital letter
Indicates a window name. Names of keys on the keyboard have initial capitals. For
example: Click Enter.
Italics
Indicates a window name or a field. Also can indicate a variables or parameter that is
replaced with an appropriate word or string. For example: type filename means that the
actual filename should be typed instead of the word shown in italic.
Menu Name > Menu
Option
Menu Name > Menu Option Indicates the menu structure. Device > Port > Port
Properties means the Port Properties menu option under the Port menu option that is
located under the Device menu.
vi
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Notes, Notices, and Cautions
A NOTE indicates important information that helps make better use of the
device.
A NOTICE indicates either potential damage to hardware or loss of data
and tells how to avoid the problem.
A CAUTION indicates a potential for property damage, personal injury, or
death.
Safety Cautions
Use the following safety guidelines to ensure your own personal safety and to help protect your system from potential damage.
Throughout this safety section, the caution icon (
followed.
) is used to indicate ca utions and precautions that need to be reviewed and
To reduce the risk of bodily injury, electrical shock, fire, and damage to the equipment, observe the following precautions.


Observe and follow service markings.

Do not service any product except as explained in the system documentation.

Opening or removing covers that are marked with the triangular symbol with a l ightning bolt may expose the user to
electrical shock.

Only a trained service technician should service components inside these compartments.
If any of the following conditions occur, unplug the product from the electrical outlet a nd replace the part or contact your
trained service provider:

Damage to the power cable, extension cable, or plug.

An object has fallen into the product.

The product has been exposed to water.

The product has been dropped or damaged.

The product does not operate correctly when the operating instructions are correctly followed.

Keep your system away from radiators and heat sources. Also, do not block cooling vents.

Do not spill food or liquids on system components, and never operate the product i n a wet environment. If the system gets
wet, see the appropriate section in the troubleshooting guide or contact your trained service provider.
vii
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch

Do not push any objects into the openings of the system. Doing so can cause fire or el ectric shock by shorting out interior
components.

Use the product only with approved equipment.

Allow the product to cool before removing covers or touching internal components.

Operate the product only from the type of external power source indicated on the electrical ratings label. If unsure of the type
of power source required, consult your service provider or local power company.

To help avoid damaging the system, be sure the voltage selection switch (if provided) on the power supply is set to match the
power available at the Switch’s location:

115 volts (V)/60 hertz (Hz) in most of North and South America and some Far Eastern countries such as South Korea
and Taiwan

100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan

230 V/50 Hz in most of Europe, the Middle East, and the Far East

Also, be sure that attached devices are electrically rated to operate with the power available in your location.

Use only a pproved power c able(s). If y ou ha ve n ot been provided wi th a p ower c able f or y our s ystem or f or a ny AC powered option intended for your system, purchase a power cable that is approved for use in your country. The power cable
must be rated for the product and for the voltage and current marked on the product's electrical ratings label. The voltage and
current rating of the cable should be greater than the ratings marked on the product.

To help prevent electric shock, plug the system and peripheral power cables into properly grounded electrical outlets. These
cables are e quipped wi th t hree-prong pl ugs t o hel p e nsure p roper grounding. D o n ot use ada pter plugs or remove t he
grounding prong from a cable. If using an extension cable is necessary, use a 3-wire cable with properly grounded plugs.

Observe ex tension cab le an d pow er str ip ratings. Mak e su re th at th e total a mpere rating of all pro ducts plugged i nto th e
extension cable or power strip does not exceed 80 percent of the ampere ratings limit for the extension cable or power strip.

To help protect the system from sudden, transient increases and decreases in elect rical power, use a surge suppressor, line
conditioner, or uninterruptible power supply (UPS).

Position system cables and power cables carefully; route cables so that they cannot be stepped on or tripped over. Be sure
that nothing rests on any cables.

Do not modify power cables or plugs. Consult a licensed electrician or your power company for site modifications. Always
follow your local/national wiring rules.

When conn ecting or disconnecting power to hot-pluggable power su pplies, if of fered with y our system, o bserve t he
following guidelines:


Install the power supply before connecting the power cable to the power supply.

Unplug the power cable before removing the power supply.

If the system has multiple sources of power, disconnect power from the system by unplugging all power cables from
the power supplies.
Move products with care; ens ure that a ll casters and/or stabilizers are fi rmly connected to the system. Avoid sudden stops
and uneven surfaces.
General Precautions for Rack-Mountable Products
Observe the following precautions for rack stability and safety. Also, refer to th e rack installation documentation accompanying
the system and the rack for specific caution statements and procedures.

Systems are considered to be components in a rack. Thus, "component" refers to any system as well as to various peripherals
or supporting hardware.
viii
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
CAUTION: Installing systems in a rack without the front and side stabilizers installed could
cause the rack to tip over, potentially resulting in bodily injury under certain circumstances.
Therefore, always install the stabilizers before installing components in the rack. After
installing system/components in a rack, never pull more than one component out of the
rack on its slide assemblies at one time. The weight of more than one extended
component could cause the rack to tip over and may result in serious injury.

Before working on the rack, make sure t hat the sta bilizers are secured to the rack, extended to the floor, and that t he full
weight of the rack rests on the fl oor. Install front and sid e stabilizers on a sing le rack or front stabilizers for joined multiple
racks before working on the rack.

Always load the rack from the bottom up, and load the heaviest item in the rack first.

Make sure that the rack is level and stable before extending a component from the rack.

Use caution when pressing the co mponent rail release latch es and sliding a co mponent into or ou t of a rack; the slide rails
can pinch your fingers.

After a component is inserted into the rack, carefully extend the rail into a l ocking position, and then slide the component
into the rack.

Do not ove rload t he AC supply bra nch ci rcuit th at prov ides power to th e rack. The t otal rack lo ad should not ex ceed 80
percent of the branch circuit rating.

Ensure that proper airflow is provided to components in the rack.

Do not step on or stand on any component when servicing other components in a rack.
NOTE: A qualified electrician must perform all connections to DC power and to safety
grounds. All electrical wiring must comply with applicable local or national codes and
practices.
CAUTION: Never defeat the ground conductor or operate the equipment in the absence
of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if uncertain that suitable grounding is available.
CAUTION: The system chassis must be positively grounded to the rack cabinet frame.
Do not attempt to connect power to the system until grounding cables are connected.
Completed power and safety ground wiring must be inspected by a qualified electrical
inspector. An energy hazard will exist if the safety ground cable is omitted or
disconnected.
CAUTION: When mounting the Switch on a cement wall, a proper concrete sleeve
anchor should be used, such as the one that is included in the optional D-Link Wall Mount
kit (DRE-KIT018).
ix
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Lithium Battery Precaution
CAUTION: Incorrectly replacing the lithium battery of the Switch may cause the battery to
explode. Replace this battery only with the same or equivalent type recommended by the
manufacturer. Discard used batteries according to the manufacturer’s instructions.
Protecting Against Electrostatic Discharge
Static electricity can harm delicate components inside the system. To prevent static damage, discharge static electricity from your
body before touching any of the electronic components, such as the microprocessor. This can be done by periodically touching an
unpainted metal surface on the chassis.
The following steps can also be taken prevent damage from electrostatic discharge (ESD):
1.
When unpacking a static-sensitive component from its shipping carton, do not remove the component from the antistatic
packing material until ready to install the com ponent in the system. Just be fore unwrapping the a ntistatic packaging, be
sure to discharge static electricity from your body.
2.
When transporting a sensitive component, first place it in an antistatic container or packaging.
3.
Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads, workbench pads and an
antistatic grounding strap.
x
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Section 1
Introduction
Switch Description
Features
Ports
Front-Panel Components
LED Indicators
Rear Panel Description
Side Panel Description
This manual describes the installation, maintenance, and configurations concerning the Switch.
Switch Description
D-Link's next-gene ration DGS-3200 Series is a high perform ancee member of the D-Link xStack® fam ily. Ranging f rom
10/100Mbps edge switches to core gigabit switches, the xStack® switch family has bee n future-proof designed to provide fault
tolerance, fle xibility, port de nsity, robust security and m aximum thro ughput with a user-friendly management int erface for t he
networking professional
The Switch has a combination of 1000BASE-T ports and SFP ports that may be used in uplinking various network devices to the
Switch, including PCs, hubs and other switches to provide a gigabit Ethernet uplink in full-duplex mode. The SFP (Small Form
Factor Portable) combo ports are used with fiber-optical transceiver cabling in order to uplink various other networking devices
for a gigabit link t hat m ay spa n great dis tances. T hese SFP ports s upport full-duplex tra nsmissions and ca n be used with
DEM-310GT (1000BASE-LX), DEM-311GT (1000BASE-SX), DEM-312GT2 (100BASE-SX), DEM-314GT (1000BASE-LH),
and D EM-315GT (1 000BASE-ZX) transceivers. A dditionally, the SFP po rts can be u sed w ith D EM-210 (Single Mode
100BASE-FX) and DEM -211 (Multi Mode 100 BASE-FX) tran sceivers. Users m ay al so u se one o f the WDM Sin gle Mode
Transceivers, such as the DEM-330T/R or the DEM-331T/R.
11
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Features
The list of features below highlights the significant features of the Switch.

IEEE 802.3 compliant

IEEE 802.3z compliant

IEEE 802.3x Flow Control in full-duplex compliant

IEEE 802.3u compliant

IEEE 802.3ab compliant

IEEE 802.1p Priority Queues

IEEE 802.3ad Link Aggregation Control Protocol support up to five (DGS-3200-10), eight (DGS-3200-16), and 12 (DGS3200-24) groups with eight ports per device

IEEE 802.1X Port-based and Host-based Access Control

IEEE 802.1Q VLAN

IEEE 802.1D Spanning Tree, IEEE 802.1w Rapid Spanning Tree and IEEE 802.1s Multiple Spanning Tree support

Support jumbo frame to 10K Bytes

Access Control List (ACL) support

ISM VLAN support

Egress filter supported to drop DLF/multicast packets to zero

DHCP local relay support

Single IP Management support

Access Authentication Control utilizing TACACS, XTACACS, TACACS+, and RADIUS protocols

Supports Multiple Authentication

Dual Image Firmware

Power saving mode support

Broadcast Ping support

Dual configuration support

Simple Network Time Protocol support

System Log support

SMTP Log support

Maximum p acket forwarding rate 14 .88 million 64 -byte packets per second (DGS-3200-10), 23.81 million 64-byte packets
per second (DGS-3200-16), and 35.7 million 64-byte packets per second (DGS-3200-24)

High p erformance switch ing en gine performs fo rwarding an d filtering at fu ll wire speed up to 20Gbps (DGS-32 00-10),
32Gbps (DGS-3200-16), and 48Gbps (DGS-3200-24)

Full- and half-duplex for all gigabit ports. Full duplex allows the switch port t o simultaneously transmit and recei ve data. It
only works with connections to full-duplex-capable end stations and switches. Connections to a hub must take place at halfduplex.

Support broadcast storm control

Loopback Detection (LBD) v4.0 Trap support

Non-blocking store and forward switching scheme capability to support rate adaptation and protocol conversion

Supports Egress/Ingress bandwidth control

Efficient self-learning and address recognition mechanism enables forwarding rate at wire speed
12
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch

Address table: Supports up to 8K (DGS-3200-10)/16K (DGS-3200-16 & DGS-3200-24) MAC addresses per device

Supports a packet buffer of up to 1 Mbits (DGS-3200-10)/6 Mbits (DGS-3200-16 & DGS-3200-24)

Port Trunking with flexible load distribution and fail-over function

RADIUS Server failover

Private VLAN

IGMP Snooping support

IGMP authentication support

MLD Snooping support (MLD v1 and v2)

IP-MAC-Port Binding (IMPB) v3.6 support

SNMP support

Support flash file system for SD card

Secure Sockets Layer (SSL) and Secure Shell (SSH) support

System Severity control

Port Mirroring support

MIB support for:

RFC 1213 MIB II

RFC 4188 Bridge

RFC 1907 SNMPv2

RFC 1757 RMON

RFC 2819 RMON

RFC 1643 Ether-like MIB

RFC 2358 Ether-like MIB

RFC 2665 Ether-like MIB

RFC 2233 Interface MIB

RFC 2863 IF MIB

RFC 2618 RADIUS Authentication Client MIB

Private MIB

RFC 2674 for 802.1p

IEEE 802.1X MIB

Provides parallel LED display for port status such as link/act, speed, etc.

Web-based GUI compatible with Internet Explorer 5.5 or later, Netscape 8.0 or later, and Firefox 2.0 or later
13
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Ports

Eight (DGS-3200-10) or 14 (DGS-3200-16) or 20 (DGS-3200-24) 10BASE-T/100BASE-TX/1000BASE-T Gigabit ports

Two (DGS-3200-10 and DGS-3200-16) or four (DGS-3200-24) SFP Combo Ports (both 100FX and 1000BASE-X)

Two (DGS-3200-10 and DGS-3200-16) or four (DGS-3200-24) 1000Mbps Copper Combo Ports (10BASE-T/100BASETX/1000BASE-T)

One RS-232 DB-9 console port (DGS-3200-10 and DGS-3200-16) or one combo console with an RS-232 DB-9 console port
and an RJ-45 (DGS-3200-24) connector. The combo console ports have two kinds of connectors, one is a female DCE
RS-232 DB-9 console connector and the other is a RJ-45 console connector that is Cisco compatible. The RS-232 DB-9
console has the higher priority. The RJ-45 console port can just read information but not write when the RS-232 DB-9 and the
RJ-45 are simultaneously connected to the device.
NOTE: For customers interested in D-View, D-Link Corporation's proprietary SNMP
management software, go to the D-Link Website and download the software and manual.
14
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Front-Panel Components
The front panel o f th e Switch con sists of LED ind icators for Power, C onsole, and f or Link/Act for each port on the Switch
including SFP port LEDs. A separate table below describes LED indicators in more detail.
Figure 1- 1. Front Panel View of DGS-3200-10
Figure 1- 2. Front Panel View of DGS-3200-16
10/100M
1000M
xStack
Link
Act
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21T
Power
Combo Console
Console
SD Card
RPS
SD Card
DGS-3200-24
Figure 1- 3. Front Panel View of DGS-3200-24
LED Indicators
The DGS-3200-10 and the DGS-3200-16 support LED indicators for Power, Console, and Port LEDs.
Figure 1- 4. LED Indicators for DGS-3200-10
Figure 1- 5. LED Indicators for DGS-3200-16
The DGS-3200-24 supports LED indicators for Power, Console, RPS, SD Card, and Port LEDs.
15
22T
23T
24T
100M
1000M 21F
22F
23F
24F
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
10/100M
1000M
xStack
Link
Act
1
Power
Combo Console
Console
SD Card
RPS
SD Card
DGS-3200-24
Figure 1- 6. LED Indicators for DGS-3200-24
LED
Description
Console
This LED will blink green during the Power-On Self Test (POST). When the POST is
finished, the LED goes dark. The indicator will light steady green when an active console
link is in session via the RS-232 console port/RJ-45 connector (DGS-3200-24 only).
Power
This LED will light green after powering the Switch on to indicate the ready state of the
device. The indicator is dark when the Switch is no longer receiving power (i.e powered
off).
RPS
(DGS-3200-24 only)
This LED will light green if the Redundant Powers Supply is in use. If the indicator is off,
the RPS is not in use.
SD Card
(DGS-3200-24 only)
This LED will light green when an SD card is plugged in to the front of the Switch. The
indicator will blink green when it is in the process of reading/writing data. If the LED is red,
the read/write action has failed.
Port LEDs
One row of LEDs for each port is located above the ports on the front panel. The indicator
above the left side of a port corresponds to the port below the indicator in the upper row
of ports. The indicator above the right side of a port corresponds to the port below the
indicator in the lower row of ports. A steady green light denotes a valid 1000Mbps link on
the port while a blinking green light indicates activity on the port (at 1000Mbps). A steady
amber light denotes a valid 10 or 100Mbps link on the port while a blinking amber light
indicates activity on the port (at 10 or 100Mbps). These LEDs will remain dark if there is
no link/activity on the port.
Combo SFP Ports
LED indicators for the Combo ports are located above the ports and numbered 1/9 and
2/10 (DGS-3200-10), 15F/15T, 16F/16T (DGS-3200-16), and 21F/21T, 22F/22T, 23F/23T,
and 24F/24T (DGS-3200-24). A steady green light denotes a valid 1000Mbps link on the
port while a blinking green one indicates activity on the port (at 1000Mbps). A steady
amber light denotes a valid 100Mbps link on the port while a blinking amber one indicates
activity on the port (at 100Mbps). These LEDs will remain dark if there is no link/activity on
the port.
16
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Rear Panel Description
The rear panel contains an AC power connector.
Figure 1- 7. Rear panel view of DGS-3200-10
Figure 1- 8. Rear panel view of DGS-3200-16
Redundant Power Supply
AC LINE
100-240 VAC
50-60 Hz
1.0A MAX
Figure 1- 9. Rear panel view of DGS-3200-24
The AC power connector is a stand ard three-pronged connector that supports the power cord. Plug-in the female connector of the
provided power cord into this socket, and the male side of the cord into a power outlet. The DGS-3200-10 and the DGS-3200-16
automatically adjust their power setting to any supply voltage in the range from 100 ~ 240 VAC at 50 ~ 60 Hz. The DSG-3200-24
automatically adjusts its power setting to a ny supply voltage in the ra nge from 100 ~ 240 VAC at 60 Hz. In addition, an optional
external Redundant Power Supply (DPS-200) can be plugged into the connector displayed above. When the internal power fails,
this optional external RPS will take over all the power immediately and automatically.
17
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Side Panel Description
The system heat vents located on each side dissipate heat. Do not block these openings. Leave at least 6 inches of space at the rear
and si des of t he Switch for pro per v entilation. Be reminded th at witho ut pro per h eat d issipation and air circu lation, system
components might overheat, which could lead to system failure or even severely damage components.
Figure 1- 10. Identical Side Panels of DGS-3200-10
Figure 1- 11. Left Side Panel of DGS-3200-16
Figure 1- 12. Right Side Panel of DGS-3200-16
Figure 1- 13. Left Side Panel of DGS-3200-24
Figure 1- 14. Right Side Panel of DGS-3200-24
18
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Section 2
Installation
Package Contents
Installation Guidelines
Installing the Switch without a Rack
Rack Installation
Power On
Installing SFP Ports
Package Contents
Open the shipping carton of the Switch and carefully unpack its contents. The carton should contain the following items:

DGS-3200-10, DGS-3200-16, or DGS-3200-24 Switch

Quick Installation Guide

AC power cord

Power supply cable clip

Mounting kit (two brackets and screws)

Four rubber feet with adhesive backing

RS-232 console cable for DGS-3200-10/DGS-3200-16 or combo RS-232/RJ-45 console cable for DGS-3200-24

CD Kit for User’s Guide/CLI/D-View module
If any item is missing or damaged, please contact your local D-Link Reseller for replacement.
Installation Guidelines
Please follow these guidelines for setting up the Switch:

Install the Switch on a sturdy , level surface that can support at least 6.6 l b. (3 kg) of weight. Do not place heavy objects
on the Switch.

The power outlet should be within 1.82 meters (6 feet) of the Switch.

Visually inspect the power cord and see that it is fully secured to the AC power port.

Make sure that there is proper heat dissipation from and adequate ventilation around the Sw itch. Leave at least 10 cm (4
inches) of space at the front and rear of the Switch for ventilation.

Install the Switch in a fairly cool and dry place for the acceptable temperature and humidity operating ranges.

Install the Switch in a si te free from strong electromagnetic field generators (such as m otors), vibration, dust, and direct
exposure to sunlight.

When installing the Switch on a level surface, attach t he rubber feet to the bottom of the device. The rubber feet cushion
the Switch, protect the casing from scratches and prevent it from scratching other surfaces.
19
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Installing the Switch without a Rack
First, attach the rubber feet included with the Switch if installing on a desktop or shelf. Attach these cushioning feet on the bottom
at each corner of the device. Allow enough ventilation space between the Switch and any other objects in the vicinity.
Figure 2- 1. Prepare DGS-3200-10 for installation on a desktop or shelf
Figure 2- 2. Prepare DGS-3200-16 for installation on a desktop or shelf
Figure 2- 3. Prepare DGS-3200-24 for installation on a desktop or shelf
20
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Attaching Brackets to a Switch for Rack Mounting
The Switch can be mounted in a standard 19" rack using the provided mounting brackets. Use the following diagrams as a guide.
Figure 2- 4. Fasten mounting brackets on the DGS-3200-10
Figure 2- 5. Fasten mounting brackets on the DGS-3200-16
Figure 2- 6. Fasten mounting brackets on the DGS-3200-24
Fasten th e m ounting b rackets to the Sw itch using the screw s provided. With th e brack ets attach ed secu rely, th e Switch can be
mounted in a standard rack, as shown below.
21
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Mounting the Switch in a Standard 19" Rack
Figure 2- 7. Installing the DGS-3200-10 in a rack
Figure 2- 8. Installing the DGS-3200-16 in a rack
Figure 2- 9. Installing the DGS-3200-24 in a rack
22
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Installing the Switch on a Wall
The Switch can be mounted on a wall. Use the following diagrams and the installation steps on the next page as a guide.
NOTE: Wall mounted ears only supported on DGS-3200-10 hardware versions A3 & B1.
Figure 2- 10. Fasten mounting brackets on the back of the DGS-3200-10 to a wall
NOTE: Wall mounted ears only supported on DGS-3200-16 hardware version A2.
Figure 2- 11. Fasten mounting brackets on the back of the DGS-3200-16 to a wall
23
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Wall Installation Steps
Before beginning installation, simulate hanging the Switch by holding it against the wall with the wall mounting ears and marking
the positions of the oval holes. These holes will be used with the wall mounting ears for installing the concrete sleeve anchors.
Figure 2- 12. Illustration of each installation step
1.
Use a power drill with an 11mm diameter bit to drill four holes at the marked points, each of a depth of 37 to 40
mm.
2.
For each hole, put the smaller end of one concrete sleeve anchor into the hole.
3.
Use a hammer to firmly smack each concrete sleeve anchor into one of the four holes. Each sleeve anchor
should be nearly flush with the wall the Switch is being mounted to.
4.
Complete the installation by firmly tightening each screw.
If the Switch is being mounted on a cement wall, D-Link recommends using a concrete sleeve anchor, such as the one depicted
below that is part of the optional D-Link Wall Mount kit, DRE-KIT018. The D-Link Wall Mount kit consists of 8 screws, 4
concrete sleeve anchors, and 2 wall ears.
Figure 2- 13. Concrete sleeve anchor
Power On
1.
Plug o ne e nd of t he AC power co rd i nto the p ower co nnector of t he Switch a nd t he ot her e nd i nto t he l ocal
power source outlet.
2.
After poweri ng on th e Switch, t he LED i ndicators will m omentarily b link green. This b linking of the LED
indicators represents a reset of the system.
Power Failure
As a precaution, in the event of a power failure, unplug the Switch. When power is resumed, plug the Switch back in.
24
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Installing SFP Ports
The Switch is equipped with SFP (Sm all Form Factor Portable) ports, which are to be used with fiber-optical transceiver cabling
in order t o uplink va rious ot her networking devices for a gi gabit l ink that m ay span g reat distances. T hese SF P ports s upport
full-duplex transmissions, h ave auto-negotiation and can b e used w ith D EM-310GT ( 1000BASE-LX), D EM-311GT
(1000BASE-SX), D EM-312GT2 (1000BASE-SX), DEM-314GT ( 1000BASE-LH) and
DEM-315GT (1 000BASE-ZX)
transceivers. See the figure below for installing the SFP ports in the Switch. In addition, DEM-210 (Single Mode, 100BASE-FX)
and DEM-211* (Multi Mode, 100BASE-FX) SFP tran sceivers are supp orted. WDM transceivers sup ported in clude DEM-2 20T
(Singlemode, TX-1550/RX-1310nm), DEM-220R (Singlemode, TX-1310/RX-1550 nm), Singlemode, DEM-330T (TX-1550/RX1310nm), DEM-330R (TX-1310/RX-1550nm), DEM-331T (TX-1550/RX-1310nm), and DEM-331R (TX1310/RX-1550).
Figure 2- 14. Inserting the fiber-optic transceivers into the DGS-3200-10
Figure 2- 15. Inserting the fiber-optic transceivers into the DGS-3200-16
Figure 2- 16. Inserting the fiber-optic transceivers into the DGS-3200-24
NOTE: *The fiber-optic transceiver module DEM-211 may fail to link when inserted into
the SFP ports if the two combo copper ports are both in linking status. The solution to this
limitation is to remove the combo copper cable before using this module. Only module
DEM-211 has this limitation.
25
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Connect to RPS
The DPS-200 is connected to the Master Switch using a 14-pin DC power cable. A standard, three-pronged AC power cable
connects the redundant power supply to the main power source.
Figure 2- 17. Connecting the DGS-3200-24 to the DPS-200
1.
Insert one end of the 14-pin DC power cable into the receptacle on the switch and the other end into the redundant power
supply.
2.
Using a standard AC power cable, connect the redundant power supply to th e main AC power source. A g reen LED on
the front of the DPS-200 will glow to indicate a successful connection.
3.
Re-connect the switch to th e AC power source. The n LED ind icator will show that a redundant power supply is now in
operation.
4.
No change in switch configuration is necessary for this installation.
NOTE: See the DPS-200 documentation for more information.
CAUTION: Do not use the DGS-3200-24 with any redundant power
system other than the DPS-200.
26
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
External Redundant Power System
The DPS-200 is a redundant power-supply unit designed to conform to the voltage requirements of the switches being supported.
The DPS-200 can be installed into a DPS-900, or DPS-800 rack mount unit.
CAUTION: The AC power cord for the Switch should be disconnected before proceeding
with installation of the DPS-200.
DPS-900
The DPS-900 is a standard-size rack mount (5 standard units in height) designed to hold up to eight DPS-200 redundant power
supplies.
Figure 2- 18. Inserting the DPS-200 into the DPS-900
The RPS can be mounted in a standard 19" rack. Use the following diagram to guide you.
Figure 2- 19. Installing the DPS-900 into the equipment rack
27
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
CAUTION: Installing systems in a rack without the front and side stabilizers installed could cause the
rack to tip over, potentially resulting in bodily injury under certain circumstances. Therefore, always
install the stabilizers before installing components in the rack. After installing components in a rack, do
not pull more than one component out of the rack on its slide assemblies at one time. The weight of
more than one extended component could cause the rack to tip over and may result in injury.
DPS-800
The DPS-800 is a st andard-size rack m ount (1 st andard unit i n height) designed t o h old u p t o t wo DPS-200 redundant power
supplies.
Figure 2- 20. Installing the DPS-200 in the DPS-800
The RPS can be mounted in a standard 19" rack. Use the following diagram to guide you.
Figure 2- 21. Installing the DPS-800 in an Equipment Rack
28
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Section 3
Connecting the Switch
Switch to End Node
Switch to Switch
Connecting To Network Backbone or Server
NOTE: All high-performance N-Way Ethernet ports can support both MDI-II and MDI-X connections.
Switch to End Node
End nodes include PCs outfitted with a 10, 100 or 1000 Mbps RJ-45 Ethernet Network Interface Card (NIC) and routers.
An end node connects to the Switch via a twisted-pair UTP/STP cable. Connect the end node to any of the 1000BASE-T ports of
the Switch.
The Link/Act LEDs for each Ethe rnet port will light green or am ber when the lin k is valid. A blinking LED indicates pac ket
activity on that port.
Switch to Switch
There is a great deal of flexibility on how connections are made using the appropriate cabling.

Connect a 10BASE-T hub or switch to the Switch via a twisted-pair Category 3, 4 or 5 UTP/STP cable.

Connect a 100BASE-TX hub or switch to the Switch via a twisted-pair Category 5 UTP/STP cable.

Connect 1000BASE-T switch to the Switch via a twisted pair Category 5e UTP/STP cable.

Connect switch supp orting a fib er-optic uplin k to th e Switch’s SFP ports via fiber-optic cabling. See cabling guidelines in
Appendix B for more information.
Figure 3- 1. Connect the Switch, e.g a DGS-3200-10, to a port on a switch with straight or crossover cable
29
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Figure 3- 2. An example of a typical Switch, e.g. DGS-3200-24, connection
Connecting To Network Backbone or Server
The combo SFP ports and the 1000BASE-T ports are ideal for uplinking to a network backbone, server or server farm. The copper
ports operate at a speed of 1000, 100 or 10Mbps in full or half duplex mode. The fiber-optic ports can ope rate at both 100Mbps
and 1000Mbps in full duplex mode.
Connections to the Gigabit Ethernet ports are made using a fiber-optic cable or Category 5e copper cable, depending on the type
of port. A valid connection is indicated when the Link LED is lit.
Figure 3- 3. Switch, e.g DGS-3200-16, uplink connection to a server, PC, or switch stack
30
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Section 4
Introduction to Switch Management
Management Options
Connecting the Console Port (RS-232 DCE)
First Time Connecting to the Switch
Password Protection
SNMP Settings
IP Address Assignment
Connecting Devices to the Switch
Management Options
This system may be managed out-of-band through the console port on the front panel or in-band using Telnet. The user may also
choose the web-based management, accessible through a web browser.
1. Web-based Management Interface
After successfully installing the Switch, the user can configure the Switch, monitor the LED panel, and display statistics
graphically using a we b browser, such as Netscape Navigator (version 6.2 and higher) or Microsoft® Internet Explorer
(version 5.0 and higher).
2. SNMP-Based Management
The S witch ca n be m anaged wi th an S NMP-compatible cons ole p rogram. The S witch sup ports SNMP version 1. 0,
version 2.0 and version 3.0. The SNMP agent decodes the incoming SNMP messages and responds to requests with MIB
objects stored in the database. The SNMP agent updates the MIB objects to generate statistics and counters.
3. Command Line Interface through the Serial Port
The user ca n also c onnect a com puter or t erminal to the serial c onsole port to acce ss the Switch. T he c ommand line
interface provides complete access to all Switch management features.
31
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Connecting the Console Port (RS-232 DCE/RJ-45)
The DGS-3200-10 an d DG S-3200-16 provide an RS-23 2 ser ial por t that en ables a co nnection to a co mputer or t erminal f or
monitoring and configuring the Switch. This port is a female DB-9 connector, implemented as a data terminal equipment (DTE)
connection.
The DG S-3200-24 features a co mbo co nsole with an R S-232 ser ial port and an RJ-4 5 co nsole po rt to conn ect to th e Sw itch’s
console. The RS-232 DB-9 console has a higher priority than the the RJ-45 cons ole port. The RS-232 DB-9 console connection
can read and write information, where as the RJ-45 console port can only r ead information when a user simultaneously connects
to the Switch with the RS-232 DB-9 and RJ-45 console ports.
To use the console port, the following equipment is needed:

A terminal or a computer with both a serial port and the ability to emulate a terminal.

A null modem or crossover RS-232 cable with a female DB-9 connector for the console port on the Switch.
To connect a terminal to the console port:
Connect the female connector of the RS-232 cab le d irectly to th e co nsole p ort on the Switch, and tighten th e cap tive retaining
screws.
Connect the other end of the cable to a terminal or to the serial connector of a computer running terminal emulation software. Set
the terminal emulation software as follows:

Select the appropriate serial port (COM port 1 or COM port 2).

Set the data rate to 115200 baud.

Set the data format to 8 data bits, 1 stop bit, and no parity.

Set flow control to none.

Under Properties, select VT100 for Emulation mode.

Select Terminal keys for Function, Arrow and Ctrl keys. Make sure to use Terminal keys (not Windows keys) are selected.
NOTE: When using HyperTerminal with the Microsoft® Windows® 2000 operating system, ensure
that Windows 2000 Service Pack 2 or later is installed. Windows 2000 Service Pack 2 allows use
of arrow keys in HyperTerminal's VT100 emulation. See www.microsoft.com for information on
Windows 2000 service packs.

After you have correctly set up the terminal, plug the power cable into the power receptacle on the back of the Switch. The
boot sequence appears in the terminal.

After the boot sequence completes, the console login screen displays.

If the user has not logged into the command line interface (CLI) program, press the Enter key at the User name and password
prompts. The re i s n o default use r name and password f or t he Switch. The a dministrator m ust fi rst creat e u ser names and
passwords. If user accounts have been previously set up, log in and continue to configure the Switch.

Enter the commands to complete desired tasks. Many commands require administrator-level access privileges. Read the ne xt
section for more information on setting up user accounts. See the DGS-3200 Series CLI Manual on the documentation CD
for a list of all commands and additional information on using the CLI.

To end a management session, use the logout command or close the emulator program.
If problems occur i n making this connection on a PC, make sure the emulation is set to VT-100. The emulation settings can be
configured by clicking on the File menu in the HyperTerminal window by clicking on Properties in the drop-down menu, and then
clicking th e Settings tab . This is wh ere y ou will find th e E mulation optio ns. If you st ill d o no t see an ything, try reb ooting t he
Switch by disconnecting its power supply.
32
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Once connected to the console, the screen below will appear on the console screen. This is where the user will enter commands to
perform all the available management functions. The Switch will prompt the user to enter a user name and a password. Upon the
initial connection, there is no user name or password and therefore just press enter twice to access the command line interface.
Figure 4- 1. Boot up display in console screen
Managing the Switch for the First Time
The Switch s upports user-based security that can allow prevention of unauthorize d users from accessing t he Switch or changing
its settings. This section tells how to log onto the Switch via out-if-band console connection.
NOTE: The passwords used to access the Switch are case-sensitive; for example, "S"
is not the same as "s."
Upon initial connection to the Switch, the login screen appears (see example below).
NOTE: Press Ctrl+R to refresh the screen. This command can be used at any time to
force the console program in the Switch to refresh the console screen.
33
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Figure 4- 2. Initial screen, first time connecting to the Switch
Press Enter in both the Username and Password fields. Then access will be given to enter commands after the c ommand prompt
DGS-3200-10:4#.
There is no initial username or password. Leave the Username and Password fields blank.
NOTE: The first user automatically gets Administrator level privileges. At least one Admin-level
user account must be created for the Switch.
Password Protection
The switches do not have a d efault user name and password. One of the first tasks when settings up the Switch is to create user
accounts. Logging i n usi ng a pre defined administrator-level user nam e will gi ve the user privileged access to the Switch's
management software.
After the initial login, define new passwords for both default user names to prevent unauthorized access to the Switch, and record
the passwords for future reference.
To create an administrator-level account for the Switch, do the following:
1.
At the CLI login prompt, enter create account admin followed by the <user name> and press the Enter key.
2.
The S witch will t hen prompt t he user t o provide a password. Ty pe the <password> used fo r th e admin istrator
account being created and press the Enter key.
3.
Once en tered, the Switch will ag ain ask th e u ser t o en ter the same p assword ag ain to verify it. Typ e th e same
password and press the Enter key.
4.
A “Success” response by the Switch will verify the creation of the new administrator.
NOTE: Passwords are case sensitive. User names and passwords can be up
to 15 characters in length.
34
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
The sample below illustrates a successful creation of a new administrator-level account with the user name "newmanager".
DGS-3200-10:4#create account admin newmanager
Command: create account admin newmanager
Enter a case-sensitive new password:********
Enter the new password again for confirmation:********
Success.
DGS-3200-10:4#
Figure 4- 3. Create administrator-level account screen
NOTICE: CLI configuration commands only modify the running configuration file and are not
saved when the Switch is rebooted. To save all configuration changes in non-volatile memory,
use the save command to copy the running configuration file to the startup configuration.
SNMP Settings
Simple Network Management Protocol (SNMP) is an OSI Layer 7 (Application Layer) designed specifically for managing and
monitoring network devices. SNMP enables network management stations to read and modify the settings of gateways, routers,
switches and other network de vices. Use SNMP t o c onfigure sy stem feat ures f or p roper operation, m onitor performance an d
detect potential problems in the Switch, switch group or network.
Managed devices that support SNMP include software (referred to as an agent), which runs locally on the device. A defined set of
variables (m anaged objects) i s m aintained b y t he S NMP a gent an d used to m anage t he de vice. These o bjects are defined i n a
Management I nformation B ase (M IB), which provides a standard presentation o f t he information c ontrolled by t he o n-board
SNMP agent. SNMP defines both the format of t he MIB specifications and the protocol used to access this information over the
network.
The Switch supports SNMP versions 1, 2c, and 3. The administrator may specify which version of SNMP to use to monitor and
control the Switch. The three versions of SNMP vary in the level of security provided between the management station and the
network device.
In SNMP v.1 and v.2, user authentication is accomplished using 'community strings', which function like passwords. The remote
user SNMP application and the Switch SNMP must use the same community string. SNMP packets from any station that has not
been authenticated are ignored (dropped).
The default community strings for the Switch used for SNMP v.1 and v.2 management access are:

public - Allows authorized management stations to retrieve MIB objects.

private - Allows authorized management stations to retrieve and modify MIB objects.
SNMP v.3 uses a m ore sophisticated authentication process that is sep arated into two parts. The first part is to m aintain a lis t of
users and their attributes that are allowed to act as SNMP managers. The second part describes what each user on that list can do
as an SNMP manager.
The Switch allows groups of users to be listed and configured with a shared set of privileges. The SNMP version may also be set
for a listed group of SNMP managers. Thus, a group of SNMP managers can be created to view read-only information or receive
traps using SNMP v.1 while assigning a higher level of security to another group, granting read/write privileges using SNMP v.3.
Using S NMP v.3 i ndividual users o r groups o f S NMP m anagers ca n be al lowed t o p erform or be restricted f rom per forming
specific SNM P m anagement fun ctions. Th e fun ctions allowed or re stricted are defined usin g th e Obj ect Id entifier (OID)
associated wit h a s pecific MIB. An a dditional layer of security is availab le fo r SNMP v.3 in th at SN MP m essages m ay b e
encrypted. To read more about how to configure SNMP v.3 settings for the Switch read the section entitled Management.
Traps
Traps are m essages that alert network personnel of eve nts that occur on the Switch. The eve nts ca n be as se rious as a reboot
(someone acci dentally turned OFF the Switch), or less serious like a port status ch ange. The Switch generates tra ps and se nds
35
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
them to the trap recipient (or network manager). Typical traps include trap messages for Authentication Failure, Topology Change
and Broadcast\Multicast Storm.
MIBs
The S witch i n t he M anagement In formation B ase (MIB) st ores m anagement and counter i nformation. The Switch u ses t he
standard MIB-II Management Information Base module. Consequently, values for MIB objects can be retrieved from any SNMPbased network management software. In addition to the standard MIB-II, the Switch also supports its own proprietary enterprise
MIB as a n extended Management Information Base. The proprietary MIB may also be retrieved by specifying the MIB Object
Identifier. MIB values can be either read-only or read-write.
IP Address Assignment
An IP A ddress m ust be assi gned t o eac h s witch, which i s use d for c ommunication with a n S NMP net work m anager or ot her
TCP/IP application (for example BOOTP, TFTP). The Switch's default IP address is 10.90.90.90. The user may change the default
Switch IP address to meet the specification of your networking address scheme.
The Switch is also assigned a unique M AC address by the factor y. This MAC address cannot be ch anged, and can be found by
entering the command "show switch" into the command line interface, as shown below.
Figure 4- 4. “show switch” command
The Switch' s MAC addres s also appea rs in the Device In formation and System Information windows o f the W eb-based
management interface. The IP address for the Switch must be set before using the Web-based manager. The Switch IP address can
be automatically set using BOOTP or DHCP protocols, in which case the actual address assigned to the Switch must be known.
The IP address may be set using the Command Line Interface (CLI) over the console serial port as follows:
Starting at the command line prompt, enter the command:
config ipif System ipaddress xxx.xxx.xxx.xxx/yyy.yyy.yyy.yyy
Where the x's represent the IP address to be assigned to the IP interface named System and the y's represent the corresponding
subnet mask. Alternatively, the user can enter config ipi f Sy stem ipaddress xxx .xxx.xxx.xxx/z. Where the x's represent the IP
address t o be assigned t o the IP inte rface named Syste m and th e z represents t he c orresponding num ber of s ubnets in CIDR
notation. The IP interface named System on the Switch can be assigned an IP address and subnet mask, which can then be used to
connect a management station to the Switch's Telnet or Web-based management agent.
36
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Figure 4- 5. Assigning the Switch an IP Address
In t he a bove e xample, t he S witch was assi gned a n IP address o f 10.24.22.100 with a su bnet m ask of 255.0.0.0. The sy stem
message Success indicates t hat the comm and wa s e xecuted s uccessfully. The Switch can now be c onfigured and managed via
Telnet and the CLI or via the Web-based management.
37
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Section 5
Web-based Switch Configuration
Introduction
Logging onto the Web Manager
Web-Based User Interface
Introduction
All software functions of the Switch can be managed, configured, and monitored via the embedded web-based (HTML) interface.
Manage the Switch from remote stations anywhere on the network through a standard browser, such as Internet Explorer 5.5 or
later, Netscape 8.0 or later, or Firefox 2.0 or later. The browser acts as a universal access tool and can communicate directly with
the Switch using the HTTP protocol.
The Web-based m anagement m odule a nd the Console program (and T elnet) a re different ways t o access t he sa me interna l
switching software and configure it. Th us, all settings encountered in web-based management are t he same as t hose found in the
console program.
Logging onto the Web Manager
To begin managing the Switch, simply run the browser installed on your computer and point it to the IP address you have defined
for the device. The URL in the address bar should read something like: http://123.123.123.123, where the numbers 123 represent
the IP address of the Switch.
NOTE: The factory default IP address is 10.90.90.90.
This opens the management module's user authentication window, as seen below.
Figure 5- 1. Enter Network Password window
Enter “admin” in both the User Name field and t he Password field and click OK. This will ope n the Web-based user interface.
The Switch management features available in the web-based manager are explained below.
38
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Web-based User Interface
The user i nterface provides access to various Switch configuration and management windows, allows the user to
performance statistics, and permits graphical monitoring of the system status.
view
Areas of the User Interface
The figure below shows the user interface. Three distinct areas divide the user interface, as described in the table.
Area 2
Area 1
Area 3
Figure 5- 2. Main Web-Manager window
Area
Function
Area 1
Select the folder or window to display. Open folders and click the hyperlinked window buttons and
subfolders contained within them to display windows.
Area 2
Presents a graphical near real-time image of the front panel of the Switch. This area displays the
Switch's ports and expansion modules and shows port activity, depending on the specified mode.
Some management functions, including port monitoring are accessible here. Click the D-Link logo to
go to the D-Link website.
Area 3
Presents Switch status based on user selection and the entry of configuration data. In addition,
hyperlinks are offered for many Switch features to enable quick configuration.
39
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Web Pages
When connecting to the management mode of the Switch with a Web browser, a login screen is displayed. Enter a user name and
password to access the Switch's management mode.
Below is a list of the folders and windows available in the Web interface:
Configuration – C ontains the following main folders, windows, and related windows: System Information, Serial Port Settings,
IP Address, IPv6 Interface Settings, IPv6 Route Table, IPv6 Neighbor Settings, Port Configuration, Port Settings, Port Description,
Port Error Disabled, Static ARP Setting s, User Accounts, Syst em Lo g Con figuration, System Lo g Settings, System Lo g Ho st,
System Severity Settings, DHCP/BOOTP Relay, DHCP/BOOTP Relay Global Settin gs, DHCP/BOOTP Relay Interface Settings,
DHCP L ocal Relay Set tings, DHC P A uto Configuration Settings, M AC Ad dress A ging Ti me, W eb Set tings, Tel net Set tings,
Password En cryption, CLI Pag ing Setting s, Firmware Information, Power Sav ing Settin gs, Dual Configu ration Settin gs, SMTP
Settings, Ping Test, SNTP Settin gs, Time Settings, Tim eZone Settings, MAC Notification Setting s, MAC Notification Global
Settings, MAC Notification Port Settings, SNMP Settings, SNMP Global State Settings, SNMP Linkchange Trap Settings, SNMP
View Table, SNMP Group Table, SNMP User Table, SNMP Community Table, SNMP Host Table, SNMP v6Host Table, SNMP
Engine ID, SNMP Trap C onfiguration, R MON, CPU Filter L3 Con trol Pack et Se ttings, Single IP Man agement, an d Single IP
Settings, Topology, Firmware Upgrade, Configuration File Backup/Restore, and Upload Log File, and SD Card FS Settings.
L2 Features – Contains the following main folders, windows, and related windows: Jumbo Frame, Egress Filter Settings, 802.1Q
VLAN, Private VLAN Settings, 802.1v Protocol VLAN, 802.1v Protocol Group Settings, 802.1v Protocol VLAN Settings, MAC
Based VLAN Settings, GVRP Settings, PVID Auto Assign Settings, Port Trunking, VLAN Trunk Settings, LACP Port Settings,
Traffic Seg mentation, IGMP Sno oping, IGMP Sno oping Settings, Data Driven Learnin g Settings, ISM VLAN Settin gs, ISM
Profile Settings, IP M ulticast Pro file Settings, Limited Mu lticast Address Rang e Settings, Max Mu lticast Grou p Settings, MLD
Snooping Settings, Port Mirroring, Loopback Detection Settings, Spanning Tree, STP Bridge Global Settings, STP Port Settings,
MST Configuration Identification, STP In stance Settings, MSTP Port Information, Forwarding & Filtering, Unicast Forwarding,
Multicast Forwarding, and Multicast Filtering Mode.
QoS – Contains the following main folders, windows, and related windows: Bandwidth Control, Traffic Control, 802.1p Default
Priority, 802.1p User Priority, and QoS Scheduling Mechanism.
Security – Contains the following main folders, windows, and related windows: Safeguard Engine, Trusted Host, IP-MAC-Port
Binding, IMP Global Settings, IMP Port Se ttings, IMP Entry Settin gs, DHCP Snooping Entries, MAC Block List, Po rt Security,
Port Security Settings, Port Lo ck Entries, DHCP Server Screening, DHCP Screening Port Settings, DHCP Offer Filterin g, Guest
VLAN, 802.1X, 802.1X Settings, 802.1X User, Initialize Port(s), Reauthenticate Port(s), Authentic RADIUS Server, SSL Settings,
SSH, SSH Confi guration, SSH Authmode and Algorithm Setti ngs, SSH User Authentication Mode , Acces s Authentication
Control, Authentication Po licy an d Parameter Settin gs, Application Au thentication Settin gs, Au thentication Server Grou p,
Authentication Server Host, Login Method Lists, Enable Method Lists, Configure Local Enable Password, Enable Admin, MACbased Access Control, MAC -based Access Control Settings, MA C-based Access Control Local Settings, Web Authe ntication,
WAC Global Settings, WAC User Settings, WAC Port Settings, JWAC, JWAC Global Settings, JWAC Port Settings, JWAC User
Settings, JWAC Cu stomize Page Lan guage, JWAC C ustomize Pa ge, Multiple Au thentication, Authorization Network Stat e
Settings, Multiple Authentication Settings, Guest VLAN, IGMP Access Control Settings, and ARP Spoofing Prevention Settings.
ACL – Contains the following m ain folders, windows, and related windows: Access Configuration Wizard, Access Profile List,
CPU Access Profile List, and Time Range Settings.
Monitoring – Contains the following main folders, windows, and related windows: Device Environment, Cable Diagnostics, CPU
Utilization, Port Utilization, Packet Size, Packets, Recei ved (RX), UM B_cast (R X), Transmitted (TX), Errors, Received (R X),
Transmitted (TX), Port Access Con trol, RADIUS Authentication, RA DIUS Acc ount Client, Authenticator State, Authenticator
Statistics, Authenticator Session Statistics, Au thenticator Diagnostics, Browse ARP Table, Browse VLAN, Browse Router Port,
Browse MLD Router Port, Browse Session Table, IGMP Snooping Group, MLD Snooping Group, WAC Authenticating State,
JWAC Host Table, MAC Address Table, System Log, and MAC-based Access Control Authentication State.
Save – Contains links for Save Configuration, Save Log, and Save All.
Tools – Contains the fo llowing wind ows: Download Co nfiguration/Download Con figuration File to NV- RAM, Do wnload
Configuration File to SD Card, Download Firmware/Download Firmware to NV-RAM, Download Firmware to SD Card, Upload
Configuration File/Upload Configuration File to TFTP, Upload Log File/Upload Log File to TFTP, Reset, and Reboot System.
NOTE: Be sure to configure the user name and password in the User
Accounts window before connecting the Switch to the greater network.
40
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Appendix A – Technical Specifications
General
Standards
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE 802.3ab 1000BASE-T Gigabit Ethernet
IEEE 802.3z 1000BASE-T (SFP “Mini GBIC”)
IEEE 802.1D/2004/Spanning Tree (802.1s, 802.1w)
IEEE 802.1Q-2005 VLAN
IEEE 802.1p Priority Queues
IEEE 802.1X Network Access Control
IEEE 802.3 Nway auto-negotiation
IEEE 802.3ad Link Aggregation Control
IEEE 802.3x Full-duplex Flow Control
IEEE 802.1u Fast Ethernet
Protocols
CSMA/CD
Data Transfer Rates:
Half-duplex
Full-duplex
Ethernet
10 Mbps
20Mbps
Fast Ethernet
100Mbps
200Mbps
--
2000Mbps
Gigabit Ethernet
Fiber Optic
SFP (Mini GBIC) Support
IEEE 802.3z 1000BASE-LX (DEM-310GT transceiver)
IEEE 802.3z 1000BASE-SX (DEM-311GT transceiver)
IEEE 802.3z 1000BASE-SX (DEM-312GT2 transceiver)
IEEE 802.3z 1000BASE-LH (DEM-314GT transceiver)
IEEE 802.3z 1000BASE-ZX (DEM-315GT transceiver)
IEEE 802.3z 100BASE-FX (DEM-210 transceiver)
IEEE 802.3z 100BASE-FX (DEM-211 transceiver)
WDM Single Mode Transceiver 10km (DEM-330T/R)
WDM Single Mode Transceiver 40km (DEM-331T/R)
WDM Single Mode Transceiver 20km (DEM-220T/R)
Topology
Duplex Ring, Duplex Chain
Network Cables
Cat.5 Enhanced for 1000BASE-T
UTP Cat.5, Cat. 5 Enhanced for 100BASE-TX
UTP Cat.3, 4, 5 for 10BASE-T
EIA/TIA-568 100-ohm screened twisted-pair (STP)(100m)
41
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Physical and Environmental
Internal Power Supply
DGS-3200-10 & DGS-3200-16: AC Input: 100 – 240 VAC, 50-60 Hz
DGS-3200-24: AC Input: 100 – 240 VAC, 50-60 Hz, with RPS 200
Optional Redundant
Power Supply
(DGS-3200-24 only)
One connector in back to install optional external RPS. When internal power fails,
the optional external RPS will take over all the power supply immediately and
automatically. Supported RPS model: DPS-200
SD Card

Supports file system.
(DGS-3200-24 only)

Save multiple images, configuration files, and logs to SD card.

Boot Switch up with firmware and configuration files stored on SD card.
Fans
DGS-3200-10: No fan.
DGS-3200-16: One smart fan (default off).
DGS-3200-24: Two smart fans (default low speed).
Power Consumption
DGS-3200-10: 20.9 Watts (Max.)
DGS-3200-16: 28.9 Watts (Max.)
DGS-3200-24: 41.9 Watts (Max.)
Operating Temperature
DGS-3200-10: 0 - 40°C
DGS-3200-16 & DGS-3200-24: 0 - 50°C
Storage Temperature
-40 - 70°C
Humidity
5 - 95% non-condensing
Dimensions
DGS-3200-10 & DGS-3200-16: 280mm (W) x 180mm (D) x 43mm (H)
DGS-3200-24: 440mm (W) x 210mm (D) x 44mm (H)
Weight
DGS-3200-10: 1.69kg
DGS-3200-16: 1.86kg
DGS-3200-24: 2.43kg
EMI
CE Class A, FCC Class A, VCCI Class A, C-Tick Report
Safety
UL, CB Report
Performance
Transmission Method
Store-and-forward
Packet Buffer
DGS-3200-10: 128K Byte (1M bit) per device
DGS-3200-16 & DGS-3200-24: 786K Byte (6M bit) per device
Packet Filtering /
Forwarding Rate
Full-wire speed for all connections
MAC Address Learning
Automatic update.
1,488,095 pps per port (for 1000Mbps)
DGS-3200-10: Supports 8K MAC address
DGS-3200-16 & DGS-3200-24: Supports 16K MAC address
Priority Queues
8 Priority Queues per port
Forwarding Table Age
Time
Max age: 10-875 seconds, Default = 300
42
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Appendix B – Cables and Connectors
When co nnecting t he Switch to ano ther sw itch, a bridge or hub, a normal cable is necessary. Please review t hese products for
matching cable pin assignment.
The following diagrams and tables show the standard RJ-45 receptacle/connector and their pin assignments.
Appendix B- 1. The standard RJ-45 port and connector
RJ-45 Pin Assignments
Contact
MDI-X Port
MDI-II Port
1
RD+ (receive)
TD+ (transmit)
2
RD- (receive)
TD- (transmit)
3
TD+ (transmit)
RD+ (receive)
4
1000BASE-T
1000BASE-T
5
1000BASE-T
1000BASE-T
6
TD- (transmit)
RD- (receive)
7
1000BASE-T
1000BASE-T
8
1000BASE-T
1000BASE-T
Appendix B- 2. The standard RJ-45 pin assignments
43
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Appendix C – Module Specs and Cable Lengths
Use the following table to as a guide for the module specs and maximum cable lengths.
Standard
Media Type
Maximum Distance
Mini-GBIC
1000BASE-LX, Single-mode fiber module
10km
1000BASE-SX, Multi-mode fiber module
550m / 2km
1000BASE-LH, Single-mode fiber module
50km
1000BASE-ZX, Single-mode fiber module
80km
1000BASE-T
Category 5e UTP Cable
100m
100BASE-TX
Category 5 UTP Cable (100 Mbps)
100m
10BASE-T
Category 3, 4 or 5 UTP Cable (10 Mbps)
100m
DEM-310GT
1000Base-LX, Single-mode
10km
DEM-311GT
1000ase-SX, Mutli-mode
500m
DEM-312GT2
1000Base-SX, Multi-mode
2km
DEM-314GT
1000BASE-LH, Single-mode
50km
DEM-315GT
1000BASE-ZX, Single-mode
80km
DEM-210
100BASE-FX, Single-mode
15km
DEM-211
100BASE-FX, Multi-mode
2km
DEM-220T
100BASE-BX, Single-mode
up to 20km
DEM-220R
100BASE-BX, Single-mode
up to 20km
DEM-330T
TX-1550/RX-1310nm, Single-mode
up to 10km
DEM-330R
TX-1310/RX-1550 nm, Single-mode
up to 10km
DEM-331T
TX-1550/RX-1310 nm, Single-Mode
up to 40km
DEM-331R
TX-1310/RX-1550 nm, Single-Mode
up to 40km
44
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
Appendix D – Glossary
1000BASE-SX: A short laser wavelength on multimode fiber optic cable for a maximum length of 2 kilometers.
1000BASE-LX: A long wavelength for a "long haul" fiber optic cable for a maximum length of 10 kilometers.
100BASE-FX: 100Mbps Ethernet implementation over fiber.
100BASE-TX: 100Mbps Ethernet implementation over Category 5 and Type 1 Twisted Pair cabling.
10BASE-T: The IEEE 802.3 specification for Ethernet over Unshielded Twisted Pair (UTP) cabling.
aging: The automatic removal of dynamic entries from the Switch Database which have timed-out and are no longer valid.
ATM: Asynchronous Transfer Mode. A connection oriented transmission protocol based on fixed length cells (packets). ATM is
designed to carry a complete range of user traffic, including voice, data and video signals.
auto-negotiation: A feature on a port wh ich allows it to adv ertise its capabilities fo r sp eed, duplex and flow contro l. When
connected to an end station that also supports auto-negotiation, the link can self-detect its optimum operating setup.
backbone port: A port which does not learn device addresses, and which receives all frames with an unknown address. Backbone
ports are normally used to connect the Switch to the backbone of your network. Note that backbone ports were formerly known as
designated downlink ports.
backbone: The part of a network used as the primary path for transporting traffic between network segments.
bandwidth: Information capacity, measured in bits per second, that a channel can transmit. The bandwidth of Ethernet is 10Mbps,
the bandwidth of Fast Ethernet is 100Mbps.
baud rate: The switching speed of a line. Also known as line speed between network segments.
BOOTP: The BOOTP protocol allows automatic mapping of an IP address to a given MAC address each time a device is started.
In addition, the protocol can assign the subnet mask and default gateway to a device.
bridge: A device that interconnects local or remote networks no matter what higher level protocols are involved. Bridges form a
single logical network, centralizing network administration.
broadcast: A message sent to all destination devices on the network.
broadcast s torm: Mu ltiple si multaneous broadcasts th at typ ically ab sorb av ailable n etwork bandwidth an d can cau se n etwork
failure.
console port: The port on the Switch accepting a terminal or modem connector. It changes the parallel arrangement of data within
computers to the serial form used on data transmission links. This port is most often used for dedicated local management.
CSMA/CD: Channel access method used by Ethernet and IEEE 802.3 standards in which devices transmit only after finding the
data ch annel clear fo r some p eriod of tim e. When two devices tran smit si multaneously, a co llision o ccurs and t he co lliding
devices delay their retransmissions for a random amount of time.
data center s witching: The point of aggregation within a corporate network where a switch provides high-performance access to
server farms, a high-speed backbone connection and a control point for network management and security.
Ethernet: A LAN sp ecification developed jointly by Xerox, Intel and Digital Equipment Corporation. Ethernet networks operate
at 10Mbps using CSMA/CD to run over cabling.
Fast Ethernet: 100Mbps technology based on the CSMA/CD network access method.
Flow Control: (IEEE 802.3X) A means of holding packets back at the transmit port of the connected end station. Prevents packet
loss at a congested switch port.
forwarding: The process of sending a packet toward its destination by an internetworking device.
full duple x: A syste m that allows packets to be transmitted and received at t he same time and, i n effect, doubles the potential
throughput of a link.
half duplex: A system that allows packets to be transmitted and received, but not at the same time. Contrast with full duplex.
IP address: Internet Protocol address. A unique identifier for a device attached to a network using TCP/IP. The address is written
as four o ctets separated with fu ll-stops (periods), an d i s made up of a network sect ion, a n o ptional sub net sect ion an d a host
section.
IPX: Internetwork Packet Exchange. A protocol allowing communication in a NetWare network.
LAN - Local Area Ne twork: A network of connected computing resources (such as PCs, printers, servers) covering a relatively
small geographic area (usually not larger than a floor or building). Characterized by high data rates and low error rates.
45
xStack® DGS-3200 Series Layer 2 Gigabit Ethernet Managed Switch
latency: The delay between the time a device receives a packet and the time the packet is forwarded out of the destination port.
line speed: See baud rate.
main port: The port in a resilient link that carries data traffic in normal operating conditions.
MDI - Mediu m Dependent Interface: An Et hernet port co nnection where t he transmitter o f one d evice is co nnected t o the
receiver of another device.
MDI-X - Me dium Dependent Interface Cross-over: An Et hernet port connection where the internal transmit and recei ve lines
are crossed.
MIB - Management Information Base: Stores a device's management charact eristics and parameters. M IBs are used by t he
Simple Net work M anagement P rotocol (SNMP) t o c ontain at tributes of t heir m anaged sy stems. The S witch co ntains i ts own
internal MIB.
multicast: Si ngle packets c opied t o a specific subset of network addresses. These address es are specified in th e destinationaddress field of the packet.
protocol: A set of rules for communication between devices on a network. The rules dictate format, timing, sequencing and error
control.
resilient link: A pair of ports that can be configured so that o ne will take over data transmission should the other fail. See also
main port and standby port.
RJ-45: Standard 8-wire connectors for IEEE 802.3 10BASE-T networks.
RMON: Remote Monitoring. A subset of SNMP MIB II that allows monitoring and management capabilities by addressing up to
ten different groups of information.
RPS - Redundant Power System: A device that provides a backup source of power when connected to the Switch.
server farm: A cluster of servers in a centralized location serving a large user population.
SLIP - Serial Line Internet Protocol: A protocol which allows IP to run over a serial line connection.
SNMP - Simple Network Ma nagement Prot ocol: A protocol o riginally desi gned t o be u sed i n managing TC P/IP i nternets.
SNMP i s p resently im plemented on a wide ran ge o f c omputers and networking e quipment and m ay be use d t o manage m any
aspects of network and end station operation.
Spanning Tre e Protoc ol (STP): A bridge-based system for providing fault tolerance on networks. STP works by allowing the
user t o im plement p arallel p aths for n etwork tr affic, and en sure th at redundant p aths ar e disabled wh en th e main p aths ar e
operational and enabled if the main paths fail.
standby port: The port in a resilient link that will take over data transmission if the main port in the link fails.
switch: A d evice wh ich filters, forwards an d flood s packets b ased on the p acket's destin ation add ress. Th e switch learn s t he
addresses associated with each switch port and builds tables based on this information to be used for the switching decision.
TCP/IP: A layered set of communications protocols providing Telnet terminal emulation, FTP file transfer, and other services for
communication among a wide range of computer equipment.
Telnet: A TCP/IP application protocol that provides virtual terminal service, letting a user log in to another computer system and
access a host as if the user were connected directly to the host.
TFTP - Triv ial File Tra nsfer Protocol: Allows the user to transfer files (such as software upgrades) from a remote device using
your switch's local management capabilities.
UDP - User Da tagram Protocol: An I nternet st andard pr otocol t hat allows a n a pplication p rogram on one device t o se nd a
datagram to an application program on another device.
VLAN - Vir tual LA N: A group of location- and topology-independent devices that communicate as i f they are on a c ommon
physical LAN.
VLT - Virtual LAN Trunk: A Switch-to-Switch link which carries traffic for all the VLANs on each Switch.
VT100: A type of terminal that uses ASCII characters. VT100 screens have a text-based appearance.
46
Subject to the terms and conditions set forth herein, D-Link Systems, Inc. (“D-Link”) provides this lifetime product warranty for hardware:


Only for products purchased, delivered and used within the fifty states of the United States, the District of Columbia, U.S. Possessions or
Protectorates, U.S. Military Installations, or addresses with an APO or FPO, and;
Only with proof of purchase.
Product Warranty: D-Link warrants that the hardware portion of the D-Link product, including internal and external power supplies and fans (“Hardware”),
will be free from material defects in workmanship and materials under normal use from the date of original retail purchase of the product (“Warranty
Period”), except as otherwise stated herein.
The customer's sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Warranty will be, at D-Link’s option, to repair or
replace the defective Hardware during the Warranty Period at no charge to the owner or to refund the actual purchase price paid. Any repair or
replacement will be rendered by D-Link at an Authorized D-Link Service Office. The replacement hardware need not be new or have an identical make,
model or part. D-Link may, at its option, replace the defective Hardware or any part thereof with any reconditioned product that D-Link reasonably
determines is substantially equivalent (or superior) in all material respects to the defective Hardware. Repaired or replacement hardware will be
warranted for the remainder of the original Warranty Period or ninety (90) days, whichever is longer, and is subject to the same limitations and exclusions.
If a material defect is incapable of correction, or if D-Link determines that it is not practical to repair or replace the defective Hardware, the actual price
paid by the original purchaser for the defective Hardware will be refunded by D-Link upon return to D-Link of the defective Hardware. All Hardware or part
thereof that is replaced by D-Link, or for which the purchase price is refunded, shall become the property of D-Link upon replacement or refund.
Software Warranty: D-Link warrants that the software portion of the product (“Software”) will substantially conform to D-Link’s then current functional
specifications for the Software, as set forth in the applicable documentation, from the date of original retail purchase of the Software for a period of ninety
(90) days (“Software Warranty Period”), provided that the Software is properly installed on approved hardware and operated as contemplated in its
documentation. D-Link further warrants that, during the Software Warranty Period, the magnetic media on which D-Link delivers the Software will be free
of physical defects. The customer's sole and exclusive remedy and the entire liability of D-Link and its suppliers under this Limited Warranty will be, at DLink’s option, to replace the non-conforming Software (or defective media) with software that substantially conforms to D-Link’s functional specifications
for the Software or to refund the portion of the actual purchase price paid that is attributable to the Software. Except as otherwise agreed by D-Link in
writing, the replacement Software is provided only to the original licensee, and is subject to the terms and conditions of the license granted by D-Link for
the Software. Replacement Software will be warranted for the remainder of the original Warranty Period and is subject to the same limitations and
exclusions. If a material non-conformance is incapable of correction, or if D-Link determines in its sole discretion that it is not practical to replace the nonconforming Software, the price paid by the original licensee for the non-conforming Software will be refunded by D-Link; provided that the non-conforming
Software (and all copies thereof) is first returned to D-Link. The license granted respecting any Software for which a refund is given automatically
terminates.
Non-Applicability of Warranty: The Warranty provided hereunder for D-Link's products will not be applied to and does not cover any products obtained
through a special or unique pricing agreement, if such agreement provides for warranty terms different from those normally provided with the product or
set forth herein, nor to any refurbished product and any product purchased through the inventory clearance or liquidation sale or other sales in which DLink, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product and in that case, the product is being sold "As-Is"
without any warranty whatsoever including, without limitation, the Warranty as described herein, notwithstanding anything stated herein to the contrary.
Submitting A Claim: The customer shall return the product to the original purchase point based on its return policy. In case the return policy period has
expired and the product is within warranty, the customer shall submit a claim to D-Link as outlined below:

The customer must submit with the product as part of the claim a written description of the Hardware defect or Software nonconformance in sufficient
detail to allow D-Link to confirm the same, along with proof of purchase of the product (such as a copy of the dated purchase invoice for the product).

The customer must obtain a Case ID Number from D-Link Technical Support by going to https://support.dlink.com, who will attempt to assist the
customer in resolving any suspected defects with the product. If the product is considered defective, the customer must obtain a Return Material
Authorization (“RMA”) number by completing the RMA form and entering the assigned Case ID Number at https://rma.dlink.com/.

After an RMA number is issued, the defective product must be packaged securely in the original or other suitable shipping package to ensure that it
will not be damaged in transit, and the RMA number must be prominently marked on the outside of the package. Include any manuals or
accessories in the shipping package.

The customer is responsible for all in-bound shipping charges to D-Link. No Cash on Delivery (“COD”) is allowed. Products sent COD will either be
rejected by D-Link or become the property of D-Link. Products shall be fully insured by the customer and shipped to D-Link Systems, Inc., 17595
Mt. Herrmann, Fountain Valley, CA 92708. D-Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or
replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link. Return shipping charges shall be
prepaid by D-Link if you use an address in the United States, otherwise we will ship the product to you freight collect. Expedited shipping is available
upon request and provided shipping charges are prepaid by the customer.
D-Link may reject or return any product that is not packaged and shipped in strict compliance with the foregoing requirements, or for which an RMA
number is not visible from the outside of the package. The product owner agrees to pay D-Link’s reasonable handling and return shipping charges for any
product that is not packaged and shipped in accordance with the foregoing requirements, or that is determined by D-Link not to be defective or nonconforming.
What Is Not Covered: The Warranty provided herein by D-Link does not cover: Products that, in D-Link’s judgment, have been subjected to abuse,
accident, alteration, modification, tampering, negligence, misuse, faulty installation, lack of reasonable care, repair or service in any way that is not
contemplated in the documentation for the product, or if the model or serial number has been altered, tampered with, defaced or removed; Initial
installation, installation and removal of the product for repair, and shipping costs; Operational adjustments covered in the operating manual for the product,
and normal maintenance; Damage that occurs in shipment, due to act of God, failures due to power surge, and cosmetic damage; Any hardware,
software, firmware or other products or services provided by anyone other than D-Link; and Products that have been purchased from inventory clearance
or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product.
While necessary maintenance or repairs on your Product can be performed by any company, we recommend that you use only an Authorized D-Link
Service Office. Improper or incorrectly performed maintenance or repair voids this Warranty.
Disclaimer of Other Warranties: EXCEPT AS SPECIFICALLY SET FORTH ABOVE OR AS REQUIRED BY LAW, THE PRODUCT IS PROVIDED “ASIS” WITHOUT ANY WARRANTY OF ANY KIND WHATSOEVER INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IF ANY IMPLIED WARRANTY CANNOT BE DISCLAIMED IN ANY
TERRITORY WHERE A PRODUCT IS SOLD, THE DURATION OF SUCH IMPLIED WARRANTY SHALL BE LIMITED TO NINETY (90) DAYS. EXCEPT
AS EXPRESSLY COVERED UNDER THE WARRANTY PROVIDED HEREIN, THE ENTIRE RISK AS TO THE QUALITY, SELECTION AND
PERFORMANCE OF THE PRODUCT IS WITH THE PURCHASER OF THE PRODUCT.
Limitation of Liability: TO THE MAXIMUM EXTENT PERMITTED BY LAW, D-LINK IS NOT LIABLE UNDER ANY CONTRACT, NEGLIGENCE,
STRICT LIABILITY OR OTHER LEGAL OR EQUITABLE THEORY FOR ANY LOSS OF USE OF THE PRODUCT, INCONVENIENCE OR DAMAGES OF
ANY CHARACTER, WHETHER DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO, DAMAGES FOR LOSS
OF GOODWILL, LOSS OF REVENUE OR PROFIT, WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, FAILURE OF OTHER
EQUIPMENT OR COMPUTER PROGRAMS TO WHICH D-LINK’S PRODUCT IS CONNECTED WITH, LOSS OF INFORMATION OR DATA
CONTAINED IN, STORED ON, OR INTEGRATED WITH ANY PRODUCT RETURNED TO D-LINK FOR WARRANTY SERVICE) RESULTING FROM
THE USE OF THE PRODUCT, RELATING TO WARRANTY SERVICE, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, EVEN IF D-LINK
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE SOLE REMEDY FOR A BREACH OF THE FOREGOING WARRANTY IS
REPAIR, REPLACEMENT OR REFUND OF THE DEFECTIVE OR NON-CONFORMING PRODUCT. THE MAXIMUM LIABILITY OF D-LINK UNDER
THIS WARRANTY IS LIMITED TO THE PURCHASE PRICE OF THE PRODUCT COVERED BY THE WARRANTY. THE FOREGOING EXPRESS
WRITTEN WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ANY OTHER WARRANTIES OR REMEDIES, EXPRESS, IMPLIED
OR STATUTORY.
Lifetime Warranty: IF LOCAL LAW MANDATES THE USE OF A DEFINITION OF “LIFETIME WARRANTY” DIFFERENT FROM THAT PROVIDED
HEREIN, THEN THE LOCAL LAW DEFINITION WILL SUPERSEDE AND TAKE PRECEDENCE, TO THE EXTENT NECESSARY TO COMPLY.
Governing Law: This Warranty shall be governed by the laws of the State of California. Some states do not allow exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so the foregoing limitations and exclusions may not apply. This Warranty
provides specific legal rights and you may also have other rights which vary from state to state.
Trademarks: D-Link is a registered trademark of D-Link Systems, Inc. Other trademarks or registered trademarks are the property of their respective
owners.
Copyright Statement: No part of this publication or documentation accompanying this product may be reproduced in any form or by any means or used
to make any derivative such as translation, transformation, or adaptation without permission from D-Link Corporation/D-Link Systems, Inc., as stipulated
by the United States Copyright Act of 1976 and any amendments thereto. Contents are subject to change without prior notice. Copyright 2009 by D-Link
Corporation/D-Link Systems, Inc. All rights reserved.
CE Mark Warning: This is a Class A product. In a residential environment, this product may cause radio interference, in which case the user may be
required to take adequate measures.
FCC Statement: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communication. However, there is no guarantee that interference will not occur in a particular installation. Operation of this equipment in a residential
environment is likely to cause harmful interference to radio or television reception. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:




Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding
local D-Link office.
Product Registration
Register your D-Link product online at http://support.dlink.com/register/
Product registration is entirely voluntary and failure to complete or return this form will
not diminish your warranty rights.
Tech Support
Technical Support
You can find software updates and user documentation on the DLink website.
D-Link provides free technical support for customers within the
United States and within Canada for the duration of the service
period, and warranty confirmation service, during the warranty
period on this product. U.S. and Canadian customers can contact
D-Link technical support through our website, or by phone.
Tech Support for customers within the United States:
D-Link Technical Support over the Telephone:
USA - 877-DLINK-55 (877-354-6555)
D-Link Technical Support over the Internet:
http://support.dlink.com
Tech Support for customers within Canada:
D-Link Technical Support over the Telephone:
877-354-6560
D-Link Technical Support over the Internet:
http://support.dlink.com
Technical Support
United Kingdom (Mon-Fri)
Home Wireless/Broadband 0871 873 3000 (9.00am–06.00pm, Sat 10.00am-02.00pm)
Managed, Smart, & Wireless Switches, or Firewalls 0871 873 0909 (09.00am – 05.30pm)
(BT 10ppm, other carriers may vary.)
Ireland (Mon-Fri)
All Products 1890 886 899 (09.00am-06.00pm, Sat 10.00am-02.00pm)
€0.05ppm peak, €0.045ppm off peak Times
Internet
http://www.dlink.co.uk
ftp://ftp.dlink.co.uk
Technische Unterstützung
Deutschland:
Österreich:
Schweiz:
Web:
http://www.dlink.de
Telefon:
+49(0)1805 2787
Zeiten:
Mo. –Fr. 08:30 – 17:30 Uhr
Web:
http://www.dlink.at
Telefon:
+43(0)820 480084
Zeiten:
Mo. –Fr. 08:30 – 17:30 Uhr
Web:
http://www.dlink.ch
Telefon:
+41(0)848 331100
Zeiten:
Mo. –Fr. 08:30 – 17:30 Uhr
0,14 € pro Minute
0,116 € pro Minute
0,08 CHF pro Minute
* Gebühren aus Mobilnetzen und von anderen Providern können abweichen.
Assistance technique
Assistance technique D-Link sur internet :http://www.dlink.fr
Assistance technique D-Link par téléphone : 0820 0803 03
0.12 € TTC/min depuis un poste fixe
Du lundi au vendredi de 9h à 19h (hors jours fériés)
Asistencia Técnica
Asistencia Técnica Telefónica de D-Link: +34 902 30 45 45
0,067 €/min
De Lunes a Viernes de 9:00 a 19:00
http://www.dlink.es
Supporto tecnico
Supporto Tecnico dal lunedì al venerdì dalle ore 9.00 alle ore 19.00 con orario
continuato
Telefono: 199400057
http://www.dlink.it/support
TECHNISCHE ONDERSTEUNING
Technische ondereuning voor klanten in Nederland:
www.dlink.nl / 0900 501 2007 / €0.15per minuut.
Tech Support for customers within Belgium:
www.dlink.be / 070 66 06 40 / €0.175per minuut(spitsuren), €0.0875per minuut(daluren)
Technische ondereuning voor klanten in Luxemburg:
www.dlink.be / +32 70 66 06 40
Pomoc techniczna
Telefoniczna pomoc techniczna firmy D-Link: 0 801 022 021
Pomoc techniczna firmy D-Link świadczona przez Internet:
http://www.dlink.eu/support/
Technická podpora
Web: http://www.dlink.cz/support/
E-mail: support@dlink.cz
Telefon ČR: +420 211 151 640 nebo SK: +421 (0)692 147 110
Telefonická podpora je v provozu: PO - PÁ od 09:00 do 17:00
Volání je zpoplatněno dle příslušných tarifů Vašeho operátora.
Technikai Támogatás
Tel. : 06 1 461-3001
Fax : 06 1 461-3004
Land Line 14,99 HUG/min - Mobile 49.99,HUF/min
email : support@dlink.hu
URL : http://www.dlink.hu
Teknisk Support
D-Link Teknisk Support over Internett: http://www.dlink.no
D-Link Teknisk telefonsupport: 820 00 755
(Hverdager 08:00-20:00)
Teknisk Support
D-Link teknisk support over telefonen: Tlf.: 9013 8899
Normale åbningstider: Hverdage kl. 08:00 - 20:00
D-Link teknisk support på Internettet: http://www.dlink.dk
Teknistä tukea asiakkaille Suomessa:
Internetin kautta : http://www.dlink.fi
Arkisin klo. 9 - 21
Numerosta : 0600 155 57
Teknisk Support
D-Link Teknisk Support via Internet: http://www.dlink.se
D-Link Teknisk Support via telefon: 0900-100 77 00
Vardagar 08:00-20:00
Assistência Técnica
Assistência Técnica da D-Link na Internet:
http://www.dlink.pt
e-mail: soporte@dlink.es
Τεχνική Υποστήριξη
D-Link Hellas Support Center
Κεφαλληνίας 64, 11251 Αθήνα,
Τηλ: 210 86 11 114 (Δευτέρα- Παρασκευή 09:00-17:00)
Φαξ: 210 8611114
http://www.dlink.gr/support
Tehnička podrška
Hvala vam na odabiru D-Link proizvoda. Za dodatne informacije, podršku
i upute za korištenje uređaja, molimo vas da posjetite D-Link internetsku
stranicu na www.dlink.eu
www.dlink.biz/hr
Tehnična podpora
Zahvaljujemo se vam, ker ste izbrali D-Link proizvod. Za vse nadaljnje
informacije, podporo ter navodila za uporabo prosimo obiščite D-Link - ovo
spletno stran www.dlink.eu
www.dlink.biz/sl
Suport tehnic
Vă mulţumim pentru alegerea produselor D-Link. Pentru mai multe informaţii,
suport şi manuale ale produselor vă rugăm să vizitaţi site-ul D-Link www.dlink.eu
www.dlink.ro
Technical Support
You can find software updates and user do cumentation on the D-Link website.
Tech Support for customers in
Australia:
Tel: 1300-766-868
24/7 Technical Support
Web: http://www.dlink.com.au
E-mail: support@dlink.com.au
India:
Tel: +91-22-27626600
Toll Free 1800-22-8998
Web: www.dlink.co.in
E-Mail: helpdesk@dlink.co.in
Singapore, Thailand, Indonesia, Malaysia,
Philippines, Vietnam:
Singapore - www.dlink.com.sg
Thailand - www.dlink.co.th
Indonesia - www.dlink.co.id
Malaysia - www.dlink.com.my
Philippines - www.dlink.com.ph
Vietnam - www.dlink.com.vn
Korea:
Tel : +82-2-2028-1810
Monday to Friday 9:00am to 6:00pm
Web : http://d-link.co.kr
E-mail : g2b@d-link.co.kr
New Zealand:
Tel: 0800-900-900
24/7 Technical Support
Web: http://www.dlink.co.nz
E-mail: support@dlink.co.nz
South Africa and Sub Sahara Region:
Tel: +27 12 661 2025
08600 DLINK (for South Africa only)
Monday to Friday 8:30am to 9:00pm South Africa
Time
Web: http://www.d-link.co.za
E-mail: support@d-link.co.za
Saudi Arabia (KSA):
Tel: +966 01 217 0008
Fax: +966 01 217 0009
Saturday to Wednesday 9.30AM to 6.30PM
Thursdays 9.30AM to 2.00 PM
E-mail: Support.sa@dlink-me.com
D-Link Middle East - Dubai, U.A.E.
Plot No. S31102,
Jebel Ali Free Zone South,
P.O.Box 18224, Dubai, U.A.E.
Tel: +971-4-8809022
Fax: +971-4-8809066 / 8809069
Technical Support: +971-4-8809033
General Inquiries: info.me@dlink-me.com
Tech Support: support.me@dlink-me.com
Egypt
1, Makram Ebeid Street - City Lights Building
Nasrcity - Cairo, Egypt
Floor 6, office C2
Tel.: +2 02 26718375 - +2 02 26717280
Technical Support: +2 02 26738470
General Inquiries: info.eg@dlink-me.com
Tech Support: support.eg@dlink-me.com
Kingdom of Saudi Arabia
Office # 84 ,
Al Khaleej Building ( Mujamathu Al-Khaleej)
Opp. King Fahd Road, Olaya
Riyadh - Saudi Arabia
Tel: +966 1 217 0008
Technical Support:
+966 1 2170009 / +966 2 6522951
General Inquiries: info.sa@dlink-me.com
Tech Support: support.sa@dlink-me.com
Pakistan
Islamabad Office:
61-A, Jinnah Avenue, Blue Area,
Suite # 11, EBC, Saudi Pak Tower,
Islamabad - Pakistan
Tel.: +92-51-2800397, 2800398
Fax: +92-51-2800399
Karachi Office:
D-147/1, KDA Scheme # 1,
Opposite Mudassir Park, Karsaz Road,
Karachi – Pakistan
Phone: +92-21-34548158, 34326649
Fax: +92-21-4375727
Technical Support: +92-21-34548310, 34305069
General Inquiries: info.pk@dlink-me.com
Tech Support: support.pk@dlink-me.com
Technical Support
You can find software updates and user documentation on the D-Link website.
Tech Support for customers in
Iran
Unit 5, 5th Floor, No. 20, 17th Alley , Bokharest
St. , Argentine Sq. ,
Tehran IRAN
Postal Code : 1513833817
Tel: +98-21-88880918,19
+98-21-88706653,54
General Inquiries: info.ir@dlink-me.com
Tech Support: support.ir@dlink-me.com
Morocco
M.I.T.C
Route de Nouaceur angle RS et CT 1029
Bureau N° 312 ET 337
Casablanca , Maroc
Phone : +212 663 72 73 24
Email: support.na@dlink-me.com
Lebanon RMA center
Dbayeh/Lebanon
PO Box:901589
Tel: +961 4 54 49 71 Ext:14
Fax: +961 4 54 49 71 Ext:12
Email: taoun@dlink-me.com
Bahrain
Technical Support: +973 1 3332904
Kuwait:
Technical Support: + 965 22453939 / +965
22453949
Türkiye Merkez İrtibat Ofisi
Ayazağa Maslak yolu
Erdebil Cevahir İş Merkezi No: 5/A Ayazağa /
Maslak İstanbul
Tel: +90 212 2895659
Ücretsiz Müşteri Destek Hattı: 0 800 211 00 65
Web:www.dlink.com.tr
Teknik Destek: support.tr@dlink.com.tr
Israel
20 ‫רח' המגשימים‬
49348 ‫ פ"ת‬,‫קרית מטלון‬
7060 .‫ד‬.‫ת‬
77-11-277-073 :‫טלפון‬
info@dlink.co.il :‫מאייל כללי‬-‫אי‬
support@dlink.co.il :‫מאייל תמיכה‬-‫אי‬
Техническая поддержка
Обновления программного обеспечения и документация доступны на Интернет-сайте D-Link.
D-Link предоставляет бесплатную поддержку для клиентов в течение гарантийного срока.
Клиенты могут обратиться в группу технической поддержки D-Link по телефону или через
Интернет.
Техническая поддержка D-Link:
+7(495) 744-00-99
Техническая поддержка через Интернет
http://www.dlink.ru
e-mail: support@dlink.ru
Офисы
Украина,
04080 г. Киев , ул. Межигорская, 87-А, офис 18
Тел.: +38 (044) 545-64-40
E-mail: kiev@dlink.ru
Грузия
0162, г. Тбилиси,
проспект Чавчавадзе 74, 10 этаж
Тел./Факс: + 995 (32) 244-563
Беларусь
220114, г. Минск, проспект Независимости,
169 , БЦ "XXI Век"
Тел.: +375(17) 218-13-65
E-mail: minsk@dlink.ru
Lietuva
09120, Vilnius, Žirmūnų 139-303
Tel./faks. +370 (5) 236-3629
E-mail: info@dlink.lt
Казахстан,
050008, г. Алматы, ул. Курмангазы, дом 143
(уг. Муканова)
Тел./факс: +7 727 378-55-90
E-mail: almaty@dlink.ru
Узбекистан
100015, г.Ташкент, ул. Нукусская, 89
Тел./Факс: +998 (71) 120-3770, 150-2646
E-mail: tashkent@dlink.ru
Армения
0038, г. Ереван, ул. Абеляна, 6/1, 4 этаж
Тел./Факс: + 374 (10) 398-667
E-mail: erevan@dlink.ru
Eesti
Peterburi tee 46-205
11415, Tallinn, Eesti , Susi Bürookeskus
tel +372 613 9771
e-mail: info@dlink.ee
Latvija
Mazā nometņu 45/53 (ieeja no Nāras ielas)
LV-1002, Rīga
tel.: +371 6 7618703 +371 6 7618703
e-pasts: info@dlink.lv
SOPORTE TÉCNICO
Usted puede encontrar actualizaciones de softwares o firmwares y
documentación para usuarios a través de nuestro sitio www.dlinkla.com
SOPORTE TÉCNICO PARA USUARIOS EN LATINO AMERICA
Soporte técnico a través de los siguientes teléfonos de D-Link
PAIS
NUMERO
Argentina
0800 - 12235465
Chile
800 - 835465 ó (02) 5941520
Colombia
01800 - 9525465
Costa Rica
0800 - 0521478
Ecuador
1800 - 035465
El Salvador
800 - 6335
Guatemala
1800 - 8350255
México
01800 - 1233201
Panamá
011 008000525465
Perú
0800 - 00968
Venezuela
0800 - 1005767
Soporte Técnico de D-Link a través de Internet
Horario de atención Soporte Técnico en www.dlinkla.com
e-mail: soporte@dlinkla.com & consultas@dlinkla.com
Suporte Técnico
Caso tenha dúvidas na instalação do produto, entre em
contato com o Suporte Técnico D-Link por:
Chat Online
www.dlink.com.br/suporte
E-mail
suporte@dlink.com.br
Back Office
backoffice@dlink.com.br *
*Acionar Garantia para 4 ou mais equipamentos
Telefones
São Paulo: (11) 2755-6950
*GO: 4052-1850 (Ligação local)
*Nordeste: 0800-7024104
*Demais Estados: 4062-1850 (Ligação local)
*Apenas Modems ADSL
Garantia diferenciada vendida pela internet. Agilidade e
tranquilidade para suas atividades!
Conheça: http://garantiapremium.dlink.com.br
Atendimento disponível das 9h as 21h de segunda a sexta
feira e aos sábados das 9h as 15h
D-Link 友訊科技 台灣分公司
技術支援資訊
如果您還有任何本使用手冊無法協助您解決的產品相關問題,台灣
地區用戶可以透過我們的網站、電子郵件或電話等方式與D-Link台灣
地區技術支援工程師聯絡。
D-Link 免付費技術諮詢專線
0800-002-615
服務時間:週一至週五,早上9:00到晚上9:00
(不含周六、日及國定假日)
網
站:http://www.dlink.com.tw
電子郵件:dssqa_service@dlink.com.tw
如果您是台灣地區以外的用戶,請參考D-Link網站全球各地
分公司的聯絡資訊以取得相關支援服務。
產品保固期限、台灣區維修據點查詢,請參考以下網頁說明:
http://www.dlink.com.tw
產品維修:
使用者可直接送至全省聯強直營維修站或請洽您的原購買經銷商。
Dukungan Teknis
Update perangkat lunak dan dokumentasi pengguna
dapat diperoleh pada situs web D-Link.
Dukungan Teknis untuk pelanggan:
Dukungan Teknis D-Link melalui telepon:
Tel: +62-21-5731610
Dukungan Teknis D-Link melalui Internet:
Email : support@dlink.co.id
Website : http://support.dlink.co.id
Technical Support
この度は弊社製品をお買い上げいただき、誠にありがとうご
ざいます。
下記弊社 Web サイトからユーザ登録及び新製品登録を
行っていただき、ダウンロードサービスにて
サポート情報、ファームウェア、ユーザマニュアルを
ダウンロードすることができます。
ディーリンクジャパン Web サイト
URL:http://www.dlink-jp.com
技术支持
办公地址:北京市东城区北三环东路 36 号 环球贸易中心 B 座
26F 02-05 室 邮编: 100013
技术支持中心电话:8008296688/ (028)66052968
技术支持中心传真:(028)85176948
各地维修中心地址请登陆官方网站查询
网址:http://www.dlink.com.cn
办公时间:周一到周五,早09:00到晚18:00
Registration Card
All Countries and Regions Excluding USA
Print, type or use block letters.
Your name: Mr./Ms_____________________________________________________________________________
Organization: ________________________________________________ Dept. ____________________________
Your title at organization: ________________________________________________________________________
Telephone: _______________________________________ Fax:________________________________________
Organization's full address: ______________________________________________________________________
____________________________________________________________________________________________
Country: _____________________________________________________________________________________
Date of purchase (Month/Day/Year): _______________________________________________________________
Product Model
Product Serial No.
* Product installed in type of
computer
* Product installed in
computer serial No.
(* Applies to adapters only)
Product was purchased from:
Reseller's name: ______________________________________________________________________________
Telephone: _______________________________________
Answers to the following questions help us to support your product:
1. Where and how will the product primarily be used?
Home Office Travel Company Business Home Business Personal Use
2. How many employees work at installation site?
1 employee 2-9 10-49 50-99 100-499 500-999 1000 or more
3. What network protocol(s) does your organization use ?
XNS/IPX TCP/IP DECnet Others_____________________________
4. What network operating system(s) does your organization use ?
D-Link LANsmart Novell NetWare NetWare Lite SCO Unix/Xenix PC NFS 3Com 3+Open Cisco Network
Banyan Vines DECnet Pathwork Windows NT Windows 98 Windows 2000/ME Windows XP
Others__________________________________________
5. What network management program does your organization use ?
D-View HP OpenView/Windows HP OpenView/Unix SunNet Manager Novell NMS
NetView 6000 Others________________________________________
6. What network medium/media does your organization use ?
Fiber-optics Thick coax Ethernet Thin coax Ethernet 10BASE-T UTP/STP
100BASE-TX 1000BASE-T Wireless 802.11b and 802.11g wireless 802.11a Others_________________
7. What applications are used on your network?
Desktop publishing Spreadsheet Word processing CAD/CAM
Database management Accounting Others_____________________
8. What category best describes your company?
Aerospace Engineering Education Finance Hospital Legal Insurance/Real Estate Manufacturing
Retail/Chain store/Wholesale Government Transportation/Utilities/Communication VAR
System house/company Other________________________________
9. Would you recommend your D-Link product to a friend?
Yes No Don't know yet
10.Your comments on this product?
__________________________________________________________________________________________
__________________________________________________________________________________________