Cello OTE-3201 User manual

SOUND BAR WITH BLUETOOTH RECEIVER

OTE-3201

LINE/MUTE

1

CONTENTS

Safety information---------------------------------------------------------- 2-5

Welcome ------------------------------------------------------------------------------6.7

Set up-------------------------------------------------------------------------------------8

Your 2.0 Speaker Bar-------------------------------------------------------------9-13

Remote Controls----------------------------------------------------------------------14

Operating and connecting an external device -----------------------------15.16

Mounting the Speaker Bar onto a wall---------------------------------------17-19

Troubleshooting---------------------------------------------------------------------20

Maintenance ------------------------------------------------------------------------21

21

Maintenance

1.Do not use harsh or abrasive cleaning agents or solvents.

2.Do not attempt to disassemble your product,other than to install the 32 to 42 extention piece.

3.Do not paint your product.

4.Do not drop, throw or try to bend your product.

5.Do not expose your product to open flames.

Technical specifications

Size

Output power

Standby power consumption

32 :800(W) 100(D) 56(H)

42 :1030(W) 100(D) 56(H)

12W+12W

1W

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS - READ CAREFULLY

BEFORE USE.

This symbol indicates that there are important operating

!!

this unit.

This symbol indicates that dangerous voltage constituting

a risk of electric shock is present within this unit.

Keep these instructions

Do not use this unit near water.

Clean only with as lightly damp cloth.

Do not block any ventilation openings.

Install in accordance with the supplied Quick Start Guide and

this User Guide.

Protect the power cord from being walked on or pinched,

particularly at plugs,and the point where it exits from the unit.

Do not allow the power cord to overhang the edge of a table.

Unplug this unit when unused for long periods of time.

2

!!

WARNING! TO REDUCE THE RISK OF FIRE OR

ELECTRICAL SHOCK,DO NOT EXPOSE THIS UNIT TO

RAIN OR MOISTURE.THE UNIT MUST NOT BE EXPOSED

TO DRIPPING AND SPLASHING AND NO OBJECTS

FILLED WITH LIQUIDS SHOULD BE PLACED ON TOP OF IT.

NOTE:No naked flames such as candles should be placed

near or underneath the unit .

IMPORTANT SAFETY INSTRUCTION(Continued)

This unit has been produced according to all current safety regulations.The following safety tips should safeguard users against careless use and the dangers connected with such use.

3

Although this appliance has been carefully manufactured and

rigorously checked prior leaving the factory,as with all electrical

appliances it is possible for problems to develop.If you notice

smoke,an excessive build up of heat or any other unexpected

phenomena,you should disconnect the plug from the mains

power socket immediately.

Ensure that the unit is sufficiently ventilated! Never place next

to or underneath curtains!

The mains plug or appliance coupler is used as the disconnect

device, the disconnect device shall remain readily operable.

This set should only be connected to a mains power supply

which matches that stated on the label on the rear of it-do

not attempt to connect it to any other type of supply.

The socket-outlet must be installed near the equipment and

easily accessible.

To prevent overload,don ' t share the same mains supply socket

with too many other items of equipment.

Troubleshooting

Problem

No power

No sound

What to do

Check that the power is switched on at the wall.

Check if the power cord is properly connected to the power outlet.

Check that the volume control is NOT at minimum setting.

Check that it is NOT set to mute.

No sound from bluetooth first connection

Check if you have entered password or not.It

".

Function disturbed

I f n o n e o f t h e a b o v e s o l u t i o n s w o r k , t h e n s w i t c h o f f a n d u n p l u g y o u r S p e a k e r s y s t e m , l e a v i n g i t f o r 2 m i n u t e s a n d t h e n s w i t c h i n g i t b a c k o n a g a i n .

The remote control won ' t work

Inspect or replace the batteries.

Make sure there are no obstacles obscuring the front of the Speaker.

20

7.Slide the Speaker Bar onto the mounting brackets, and make sure there is a firm and stable connection before letting go of the

Speaker Bar.

8.Finally, use the LEVEL to confirm that the Speaker Bar is level.

19

Apparatus with Class 1 construction shall be connected to

a mains socket outlet with a protective earthing connection.

Keep away from rodents.Rodents enjoy biting into electric flexes.

Always hold the plug when pulling out the plug from the mains

supply socket.Do not pull on the flex,the flex can become

overloaded and cause a short circuit.

Set up the unit so that no one is able to trip over the flex.

Do not place heavy items on the flex,which may damage it.

Take note that the flex cannot be reached and pulled by young

children,avoiding injury.

Do not set up the unit near to heat sources.The casing and the

flex could be damaged by the impact of heat.

Avoid placing the unit on any surfaces that may be subject

to vibrations or shocks.

When you leave your home for long periods of time,unplug the

AC power cable for safety reasons.

The unit becomes warm when in operation.Do not place any

covers or blankets on the unit in order to prevent overheating.The

ventilation holes are not to be blocked.Do not set up near radiators.

Do not place in direct sunshine.When placing on a shelf leave

5cm(2 )free space around the whole unit.

Do not allow water or moisture to enter the unit.Do NOT use in wet

or moist areas such as Bathrooms,steamy kitchens or near

swimming pools.

4

5

Do not use this unit when moisture condensation may occur.

Any repairs must be carried out by qualified personnel only.

Liquids spilt into the unit can cause serious damage.Switch the

set OFF and disconnect the mains power supply,then consult a

qualified service person before attempting to use the unit again.

Do NOT remove the safety covers.There are no useable or

serviceable parts inside.You may invalidate the warranty.

Qualified personnel must only service this apperatus.

Take good care of the remote control,do not drop.

Never place hot objects or open flame sources on or close to

the unit.

High temperatures can melt plastic and lead to fires.

To clean use a soft dry cloth.Do NOT use solvents or petrol

based fluids. For stubborn stains,you may use a damp cloth

with dilute detergent.

1. Use the TAPE MEASURE to decide how high you d like to hang

the Speaker Bar on the wall. The Speaker Bar must be hung within

6 feet of an AC power outlet for the attached AC power cord to reach.

2.Mark the position of the mounting screws on the wall using a pencil.

3.Line the LEVEL up on both of your mark sure they are level. If

they ' re not, adjust the marks as needed to make them level.

4.After you ' ve double checked your markings, DRILL holes in the wall

suitable for the wall plugs (not supplied). Be sure to use the correct

types of plugs for your wall.

5.Screw the wall mounting screws into the wall plugs.

6.Use the LEVEL to check that the mounting screws are level.

18

17

Mounting the Speaker Bar onto a wall

We recommend having this speaker professionally mounted.

By using the included wall mounting accessories ,the speaker can be mounted onto a wall.

You should have

4 pcs short screws

Welcome

Congratulations on purchasing this 2.0 Speaker Bar. The Speaker

Bar allows you to play TV audio content from an attached television,

and from your bluetooth enabled telephone, PC or Tablet.

Please read the warning section carefully before

using your Speaker Bar.

You should have

2.0CH Speaker Bar

Remote control

You will need

Level

Manual or Power Screwdriver

Pencil

Tape Measure

Suitable wall plugs for your type of wall

RCA CABLE 1

LINE OUT Cable

AC/DC adapter 1

1

1

2 3

Speaker Bar extender

screw 8pcs

STANDBY BASS 3D LINE / MUTE BT

Wall mount fittings

screw 4pcs

6

7

You may also need

RCA Cables

3.5mm line in cable

Note:

Ventilation

When placing the Speaker Bar on an entertainment center, bookshelf,or any type of enclosed space, be sure to allow at least 2-3 inches of space around the Speaker Bar for ventilation. If the Speaker Bar is enclosed in a tight space, without ventilation, heat generated from the Speaker Bar could produce a potential heat hazard.

2-3 inches

2

------

1

Headphone

Left(white) CH(red)

Audio output

TV

BLUETOOTH

MEMU

Bluetooth Settings

Press "STANDBY" button and switch on the unit. Turn "BT" function on and blue LED will flash 30 seconds. Use your mobile or other devices with bluetooth transmitters and go to search for speaker

Bar.Our device name is F-3089N. Once it has recognized, press password "0000" to connect and pair with.

Bluetooth Auto Connection

I t h a s a u t o c o n n e c t i o n f u n c t i o n . J u s t t u r n o n " B T " f u n c t i o n a n d b l u e L E D f l a s h , s o u n d b a r b l u e t o o t h w i l l a u t o m a t i c a l l y c o n n e c t a n d p a i r t o a n y d e v i c e a g a i n i f i t h a s b e e n d o n e b e f o r e .

N o t e :

T h e B T L E D c o n t i n u e s t o f l a s h i f t h e r e i s n o c o n n e c t i o n . T u r n o f f b y p r e s s i n g L I N E i n o r p o w e r .

16

15

Operating and connecting an external device

You can connect external devices (Mp3 player ,CD player ,TV etc) to the Speaker Bar in several ways.

Using a RCA audio cable

Make sure you match up the Red (R)and White (L)Audio connectors, either RCA cable or line in/out cable only.

Using a 3.5mm line-in cable

You can also connect an external device to your Speaker Bar using the LINE socket on the jack of the unit as shown .

To play the external device you will need to select LINE using the

LINE button.

Once the device is connected you can control playback as you would usually.

Press the VOLUME + and - buttons on the music system to

increase or reduce the volume.

Press the MUTE button to turn the sound off, press it again to return to the previous volume level.

Set up

Setting up your Speaker Bar

1.Plug the power cable into a standard three pin wall socket and switch the power on at the wall.

The remote control battery

1.It includes one piece of 2025 battery.

2.Remove the transparent sheet.

8

Your 2.0 Speaker Bar

Features Defined

Locations of Remote Control

2

1 4

5

6

3

8 7

9

Features Defined

1.STANDBY button: AC power is connectd but unit is in standby status.

2.BASS button: Bass effect is on.

3.3D button: 3D surround sound effect is on.

4.LINE mode button: It is connected to LINE when it is on.

5.BT mode button: Bluetooth function is on when blue LED

flashs and lights.

6.Remote sensor.Ensure this area is not covered or blocked by

9 any object.

1

4

5

7 8

6

2

3

Controls Defined

1 : S T A N D B Y b u t t o n : P r e s s t o t u r n t h e b a r s p e a k e r o f f o r o n .

2 : M U T E b u t t o n : P r e s s t o m u t e t h e v o l u m e .

3 : B A S S b u t t o n : P r e s s t o t u r n o n t h e b a s s .

4 : L I N E b u t t o n : P r e s s t o s w i t c h t o l i n e m o d e .

5 : B T b u t t o n : P r e s s t o s w i t c h t o B l u e t o o t h m o d e

6 : 3 D b u t t o n : P r e s s t o a d j u s t t h e 3 D E f f e c t .

7 : V O L - b u t t o n : P r e s s t o r e d u c e t h e v o l u m e .

8 : V O L + b u t t o n : P r e s s t o i n c r e a s e t h e v o l u m e .

14

7.DC:DC jack in,the connection for mains adapter.

8.LINE:RCA and Line in jack.

9.Mounting hole.

Note:

Where a button that appears on both the speaker and remote control is referenced in this guide you can use either button to use that function.

To change your sound bar from 32" to 42"

3. Install the front panel as photo shown

8

7 6

5

4

3

2

1

13

4. Finally, fix it with 8 screws as photo shown

1. At the rear cabinet,loosen screws (6 pcs is necessary) as photo

shown using a Philips screwdriver.

Only the screws indicated can be removed with the screw

!!

spoil the sound bar 's operation.

10

2. Take out the front panel as photo shown.

Re-assemble your sound bar with 42" extender

1. Screws (4 pcs) the extender with left and right bars as photo

shown.

11

3. Pull out the pin socket as photo shown.

2. Insert the pin socket as photo shown

12