Siemens OpenStage Asterisk User guide

Documentation
OpenScape Voice
OpenStage 40, OpenStage 40 G
OpenStage Key Module 40
Operating Manual
Communication for the open minded
V1 R3.x
V1 R4.x
Siemens Enterprise Communications
www.siemens.com/open
Important information
Important information
Q
For safety reasons, the telephone should only be supplied
with power:
• using the original power supply unit.
Part number: L30250-F600-C14x (x: 1=EU, 2=US,
3=UK) or
• in a LAN with PoE (Power over Ethernet), which complies with the IEEE 802.3af standard.
Use only original Siemens accessories. The use of other accessories may be hazardous and will render the warranty
and the CE marking invalid.
Never open the telephone or a key module. Should you encounter any problems, contact your administrator.
Trademarks
The device conforms to the EU directive 1999/5/EC as attested by the CE marking.
All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local authorities.
Proper disposal and separate collection of your old appliance will help prevent potential damage to the environment
and human health. It is a prerequisite for reuse and recycling of used electrical and electronic equipment.
For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service, the shop where you purchased the product or your
sales representative.
The statements quoted above are only fully valid for equipment which is installed and sold in the countries of the European Union and is covered by the directive 2002/96/EC.
Countries outside the European Union may impose other
regulations regarding the disposal of electrical and electronic equipment.
2
Important information
Location of the telephone
•
•
•
•
•
The telephone should be operated in a controlled environment with an
ambient temperature between 5°C and 40°C.
To ensure good speakerphone quality, the area in front of the microphone (front right) should be kept clear. The optimum speakerphone
distance is 50 cm.
Do not install the telephone in a room where large quantities of dust
accumulate; this can considerably reduce the service life of the telephone.
Do not expose the telephone to direct sunlight or any other source of
heat, as this is liable to damage the electronic components and the
plastic casing.
Do not operate the telephone in damp environments such as bathrooms.
Product support on the Internet
Information and support for our products can be found on the Internet:
http://www.siemens-enterprise.com/.
Technical notes, current information about firmware updates, frequently
asked questions and lots more can be found on the Internet at:
http://wiki.siemens-enterprise.com/.
3
Contents
Contents
Important information . . . . . . . . . . . . . . . . . . . . . . . . . .2
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Location of the telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Product support on the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
General information. . . . . . . . . . . . . . . . . . . . . . . . . . .10
About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols used in the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telephone type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speakerphone quality and display legibility . . . . . . . . . . . . . . . . . . . . . .
Single-line telephone/multi-line telephone. . . . . . . . . . . . . . . . . . . . . . .
10
10
11
11
11
11
12
Getting to know your OpenStage phone . . . . . . . . .13
The user interface of your OpenStage 40/40 G. . . . . . . . . . . . . . . . . . .
Ports on the underside of the phone. . . . . . . . . . . . . . . . . . . . . . . . . . .
Using network ports more efficiently . . . . . . . . . . . . . . . . . . . . . . .
Key Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OpenStage Key Module 40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OpenStage Key Module 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmable sensor keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trunk keys (on multi-line phones only). . . . . . . . . . . . . . . . . . . . . . .
Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle-display view and icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Context-dependent displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Telephony interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Single-line view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multi-line view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voicemail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Program/Service menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control and monitoring function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
13
14
15
16
16
17
18
18
18
19
20
21
23
25
25
25
26
28
28
29
30
30
31
33
33
34
34
Contents
Basic functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Secure voice transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a call via the handset . . . . . . . . . . . . . . . . . . . . . . . . . . .
Answering a call via the loudspeaker (speakerphone mode) . . . . . .
Accepting a call via the headset. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Directed pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Picking up call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Picking up the held call: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching from handset to speakerphone mode . . . . . . . . . . . . . . . . .
Switching from speakerphone mode to the handset . . . . . . . . . . . . . .
Switching from headset to speakerphone mode . . . . . . . . . . . . . . . . .
In standard mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
In U.S. mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Open listening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating the microphone . . . . . . . . . . . . . . . . . . . . . . . .
Ending a call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Group call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Off-hook dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
On-hook dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Immediate dialing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing using the hot or warm line function . . . . . . . . . . . . . . . . . . .
Redial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Consulting a second party . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching to the held party (alternating) . . . . . . . . . . . . . . . . . . . . .
Connecting parties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call forwarding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming call forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating/deactivating call forwarding. . . . . . . . . . . . . . . . . . . . . . .
Activating call forwarding for all calls . . . . . . . . . . . . . . . . . . . . . . . .
Call forwarding chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requesting callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Responding to a callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Permitting callback on busy/no reply . . . . . . . . . . . . . . . . . . . . . . . .
Calling back missed calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
35
36
36
37
38
38
39
40
41
42
42
42
42
43
43
44
46
46
47
48
49
50
51
52
53
54
55
57
58
59
60
60
61
62
63
5
Contents
Programming sensor keys . . . . . . . . . . . . . . . . . . . . .64
List of available functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming programmable sensor keys. . . . . . . . . . . . . . . . . . . . . . .
Programming enhanced functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repertory dial. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature toggle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Forwarding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Immediate ring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activate/deactivate call waiting . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using sensor keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example 1: Accessing a stored contact or phone number . . . . . . .
Example 2: Deactivate call waiting . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting programmable sensor keys. . . . . . . . . . . . . . . . . . . . . . . . . .
64
65
66
66
67
67
68
68
68
68
68
69
Enhanced phone functions. . . . . . . . . . . . . . . . . . . . .70
Incoming calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accepting calls via the headset . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deflecting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rejecting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring call forwarding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Placing a call on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call waiting (second call) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transferring a call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CTI calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing with the DDS key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dialing a phone number from a list . . . . . . . . . . . . . . . . . . . . . . . . .
Using autodial delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System-based conference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deleting all entries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
70
70
70
72
72
74
77
81
84
86
86
86
87
90
90
93
95
95
95
Contents
Making calls with multiple lines . . . . . . . . . . . . . . . 96
Incoming calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Accepting calls for the primary line . . . . . . . . . . . . . . . . . . . . . . . . . 96
Accepting calls for secondary lines . . . . . . . . . . . . . . . . . . . . . . . . . 96
Making calls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Manual trunk seizure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Automatic trunk seizure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Dialing the last dialed number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Forwarding calls on primary line . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
During calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Making and receiving calls on a single line . . . . . . . . . . . . . . . . . . . 99
Making and receiving calls with multiple lines. . . . . . . . . . . . . . . . . 99
Putting a line on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Lines with hot or warm line function . . . . . . . . . . . . . . . . . . . . . . . 101
Busy override. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Direct station selection keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Calling a station directly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Call pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Deflecting a call to a DSS station . . . . . . . . . . . . . . . . . . . . . . . . . 104
LED display on DSS keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Making calls in an executive-secretary team . . . . . . . . . . . . . . . . . . . . 106
Sample scenarios. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Accepting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Connecting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
DSS keys can be used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Using line overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Settings for multi-line phones (keyset) . . . . . . . . . . . . . . . . . . . . . . . . 111
Displaying the line in the "Overview" tab . . . . . . . . . . . . . . . . . . . . 111
Setting the time for a delayed ringer . . . . . . . . . . . . . . . . . . . . . . . 112
Configuring the "Overview" tab display . . . . . . . . . . . . . . . . . . . . . 113
Line preview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Rollover for a line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Privacy/security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
Deactivating the ringer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Do not disturb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enabling "Do not disturb" via a key. . . . . . . . . . . . . . . . . . . . . . . . .
Enabling "Do not disturb" via the idle menu . . . . . . . . . . . . . . . . . .
Allowing "Do not disturb" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Locking the phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
116
117
117
117
118
119
119
121
7
Contents
Mobility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
Mobility scenarios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logging on and off at the same phone . . . . . . . . . . . . . . . . . . . . .
Logging on and off at different phones . . . . . . . . . . . . . . . . . . . . .
Logging on and off at the same phone . . . . . . . . . . . . . . . . . . . . . . . .
Logging on to the phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logging off from the phone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logging on at different telephones . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logging on with forced logoff at a remote phone . . . . . . . . . . . . .
Logging on with forced, delayed logoff at a remote phone . . . . . .
123
123
123
124
124
125
126
126
127
OpenScape Voice functions. . . . . . . . . . . . . . . . . . .128
Feature toggle key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making anonymous calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temporarily activating anonymous calling for the next call . . . . . .
Temporarily deactivating anonymous calling for the next call . . . .
Creating a list for selective calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For call acceptance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For call rejection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Anonymous calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rejecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accepting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using abbreviated dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call tracing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hunt group functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Making a line busy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Marking the last line in the hunt group chain. . . . . . . . . . . . . . . . .
Reachability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Park a call. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unparking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Silent Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Active silent monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Muted silent monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of codes for OpenScape Voice functions. . . . . . . . . . . . . . . . . .
8
128
129
129
129
130
130
131
131
132
133
133
133
134
134
135
135
136
137
137
138
140
140
140
141
141
142
143
Contents
Individual phone configuration . . . . . . . . . . . . . . . 144
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the display to a comfortable reading angle . . . . . . . . . .
Setting contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Background lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contrast for the OpenStage Key Module. . . . . . . . . . . . . . . . . . . .
Date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting daylight saving time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic daylight saving time . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time display format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date display format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Volumes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nonsecure voice communication tone and message . . . . . . . . . .
Setting the language and country . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting a language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Country-specific setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting user data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Initiating the reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
144
144
144
144
145
146
146
146
147
148
148
149
150
150
151
156
157
157
159
160
161
161
Web interface (WBM). . . . . . . . . . . . . . . . . . . . . . . . 162
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calling up the Web interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Administrator Pages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User pages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
162
162
162
163
164
Fixing problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
Caring for your telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact partner in the case of problems . . . . . . . . . . . . . . . . . . . . . . .
Labeling keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
167
167
168
168
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 169
9
General information
General information
About this manual
This document contains general descriptions of the technical options,
which may not always be available in individual cases. The respective features must therefore be individually defined in the terms of the contract.
If a particular function on your phone is not available to you, this may be
due to one of the following reasons:
• The function is not configured for you or your telephone. Please contact your system support representative.
• Your communications platform does not feature this function. Please
contact your Siemens sales partner for information on how to upgrade.
This user guide is intended to help you familiarize yourself with OpenStage
and all of its functions. It contains important information on the safe and
proper operation of your OpenStage phone. These instructions should be
strictly complied with to avoid operating errors and ensure optimum use of
your multifunctional telephone in the network.
These instructions should be read and followed by every person installing,
operating or programming an OpenStage phone.
For your own protection, please read the section dealing with safety
in detail. Follow the safety instructions carefully in order to avoid endangering yourself or other persons and to prevent damage to the
unit.
This user guide is designed to be simple and easy to understand, providing
clear step-by-step instructions for operating your OpenStage phone.
Administrative tasks are dealt with in a separate manual. The Quick Reference Guide contains quick and reliable explanations of frequently used
functions.
Symbols used in the manual
Operations and settings that can be made both at the phone and over the
Web interface are indicated by an icon and page reference.
V
z
10
is a reference to an operation or setting performed directly on the
phone
is a reference to an operation or setting performed via the Web interface
General information
Service
The Siemens service department can only help you if you experience problems or defects with the phone.
Should you have any questions regarding operation, your specialist
retailer or network administrator will gladly help you.
For queries regarding connection of the telephone, please contact
your network provider.
If you experience problems or defects with the phone, please dial the service number for your country.
Intended use
The OpenStage phone is a desktop unit designed for voice transmission
and for connection to the LAN. It can also be used as a workstation device.
Any other use is regarded as unauthorized.
Telephone type
The identification details (exact product designation and serial number) of
your telephone can be found on the nameplate on the underside of the
base unit. Specific details concerning your communications platform can
be obtained from your service technician.
Please have this information ready when you contact our service department regarding faults or problems with the product.
Speakerphone quality and display legibility
•
•
To ensure good speakerphone quality, the area in front of the telephone
(front right) should be kept clear.
The optimum handsfree distance is 20 in. (50 cm).
Proceed as follows to optimize display legibility:
– Turn the phone to tilt the display. This ensures you have a frontal view
of the display while eliminating light reflexes.
– Adjust the contrast as required Æ page 144.
11
General information
Single-line telephone/multi-line telephone
Your OpenStage 40/40 G is a "multi-line telephone". This means that multiple lines can be configured, which is not the case with single-line phones.
Each line is assigned an individual phone number which you can use to
make and receive calls.
The programmable sensor keys function as line keys on multi-line phones
Æ page 21.
The "Overview" tab on the telephony interface provides information about
the lines configured on your phone and the current status of each line
Æ page 29.
A number of specific features must be considered when using a multi-line
phone to make and receive calls Æ page 96.
12
Getting to know your OpenStage phone
Getting to know your OpenStage phone
The following sections describe the most frequently used operating elements and the displays on your OpenStage phone.
The user interface of your OpenStage 40/40 G
8
2
3
4
5
6
7
1
1 You can make and receive calls as normal using the handset.
2
The graphic display permits intuitive operation of the phone
Æ page 25.
3
You can customize your telephone by assigning phone numbers and
functions to the programmable sensor keys Æ page 25.
You can use function keys when conducting a call to access frequent4 ly used functions (such as, Disconnect) or to open the Program/Service menu and mailbox Æ page 18.
5
Audio keys are also available, allowing you to optimally configure the
audio features on your telephone Æ page 18.
6 The 5-way navigator is a convenient navigation tool Æ page 19.
7 The keypad can be used to enter phone numbers and text Æ page 23.
8 Incoming calls are visually signaled via the call display.
13
Getting to know your OpenStage phone
Ports on the underside of the phone
Power supply unit
(if necessary)
PC
Network switch
Headset
Country
specific
cable
Key Module
Handset
Properties of your OpenStage 40/40 G
OpenStage
LCD display, 40 x 6 characters
Illuminated display
Programmable sensor keys
Full-duplex speakerphone function
Headset
10/100 Mbps Ethernet switch Æ page 15
1000 Mbps Ethernet switch Æ page 15
Interface for key modules
Wall mounting
14
40
;
;
6
;
;
;
-
;
;
40 G
;
;
6
;
;
-
;
;
;
Getting to know your OpenStage phone
Using network ports more efficiently
OpenStage 40 has a built-in 10/100 Mbps Ethernet switch.
OpenStage 40 G has a 1000 Mbps Ethernet switch. This means that you
can connect a PC to the LAN directly via the phone. The telephone-PC connection option must first be activated on the telephone by service personnel.
Network switch
OpenStage 40/40 G
PC
Using this connection option saves one network port for each switch used
and requires fewer or shorter network cables when arranged correctly.
15
Getting to know your OpenStage phone
Key Module
OpenStage Key Module 40
The OpenStage Key Module 40 is a key module attached to the side of the
phone that provides 12 additional illuminated, programmed keys.
Like keys on the phone, these keys can be programmed and used according to your needs Æ page 20.
You can attach up to two OpenStage Key Module 40s to your
OpenStage 40.
To operate an OpenStage Key Module 40 you always require a power supply unit Æ page 2.
16
Getting to know your OpenStage phone
OpenStage Key Module 15
The OpenStage Key Module 15 is a key module attached to the side of the
phone that provides an additional 18 illuminated, programmable sensor
keys.
Like keys on the phone, these keys can be programmed and used according to your needs.
You can only attach one OpenStage Key Module 15 to your OpenStage 40.
You cannot combine the OpenStage Key Module 15 with the
OpenStage Key Module 40.
17
Getting to know your OpenStage phone
Keys
Function keys
Key Function when key is pressed
s End (disconnect) call.
LED display
none
, Open redial list
none
r Activate/deactivate forwarding
Red: Call forwarding is
activated
the Program/Service menu
N Open
Æ page 33
Red: Menu is active
O View messages Æ page 30.
Red: New voicemail or
missed calls.
Audio keys
Key Function when key is pressed
p Activate/deactivate microphone (also for speakerphone mode)
o Activate/deactivate the headset.
- Decrease the ring, handset, and loudspeaker volume.
loudspeaker for speakerphone mode and open
n Activate/deactivate
listening
+ Increase the ring, handset, and loudspeaker volume.
18
Getting to know your OpenStage phone
Navigator
Before using the telephone, remove the protective covering from
the navigator surface.
With this control, you can manage most of your phone’s functions, as well
as its displays.
Operation
Functions when key is pressed
Press the c key.
Press the a key.
•
•
•
•
Call up the context menu
Perform action
Go down a level
Call up the context menu in the idle
display
•
•
Short press: One level back
Long press (held down): Go back to
the first level of the settings menu
Cancel function
Quit the context menu
In input fields:
Delete character to the left of the
cursor
•
•
•
Press the d key.
Press the b key.
Press the i key.
•
•
•
Scroll downwards
Select element below
Long press (held down): Jump to
the end of the list/menu
•
•
•
Scroll upwards
Select element above
Long press (held down): Jump to
the start of the list/menu
•
•
•
Confirm input
Perform action
Call up the context menu
19
Getting to know your OpenStage phone
Programmable sensor keys
Your OpenStage 40 telephone features six programmable lit sensor keys.
Increase the number of programmable sensor keys by connecting a
key module Æ page 16.
Mirea, Ch.
Level 2
Touch the key briefly to activate the programmed function or dial the stored
number Æ page 68.
Press the key to open a menu for programming it Æ page 65.
Only for repdial keys can you also program the second level for direct destination selection.
You can label these keys with internal and external phone numbers or frequently used functions (platform-dependent; please contact the responsible administrator).
The configured phone number or function name is displayed next to the
key.
The status of a function is shown by the LED on the corresponding sensor
key.
Meaning of LED displays on function keys
LED
Meaning of function key
S Off
The function is deactivated.
R On
The function is activated.
T Flashing1 Indicates the function status.
[1] In this manual, flashing sensor keys are identified by this icon, regardless of the flashing interval. The flashing interval represents different statuses, which are described in detail in
the corresponding sections of the manual.
20
Getting to know your OpenStage phone
Trunk keys (on multi-line phones only)
The programmable sensor keys on multi-line phones function as trunk
keys. Each key programmed with the "Line" function is handled as a line.
This means up to five lines can be configured.
A distinction is drawn here between primary, secondary and phantom
lines. Each of these line types can be used on a private or shared basis
Æ page 21.
Primary line
All multi-line telephones have a primary line. This line can be reached in the
usual manner via your public phone number. Incoming calls are signaled on
this line.
To avoid conflict between individual multi-line phones, the functions
"Do not disturb" and "Call forwarding" can only be used for the primary line.
Secondary line
The secondary line on your phone is used as a primary line by another subscriber of the line trunk group. Your primary line, which is configured on another telephone in the line trunk group, simultaneously functions as the
secondary line on that telephone.
Phantom line
Phantom lines are not used as primary lines by any telephones in the line
trunk group. Phantom lines are established when the number of lines provided by a communications system exceeds the number of available
telephones.
Line utilization
• Private line: A line that is used by a single telephone. This line cannot
be used as a secondary line by another telephone.
• Shared line: A line that is configured on multiple telephones. The line
status (if configured) is displayed in the "Overview" tab for all telephones that share this line. If, for example, a shared line is being used
by a telephone, a status message indicating that this line is busy is displayed on all other telephones.
• Direct call line: A line with a direct connection to another telephone.
The line status is indicated by the LED in addition to the display in the
"Overview" tab Æ page 29.
21
Getting to know your OpenStage phone
LED display
LED
S
T
Explanation
Not lit
The phone is in idle mode.
Flashing
•
•
Incoming call on the line (Æ page 96)
"Hold reminder" is activated (Æ page 75)
•
•
Outgoing call on the line
The incoming call was prioritized and selected in accordance with the "Automatic line
selection for incoming calls" option
Flickering
Fast blinking The line is on "Hold".
R
22
Blinking
Call forwarding is activated
Illuminated
The line is busy
Getting to know your OpenStage phone
Keypad
You can only use the digits 1 to 9 and 0 as well as the * and # characters
when dialing a number. The h navigation key is used to delete from right
to left.
In cases where text input is possible, you can use the keypad to input text,
punctuation and special characters in addition to the digits 0 to 9 and the
hash and asterisk symbols. To do this, press the numerical keys repeatedly.
Example: To enter the letter "h", press the number 4 key on the keypad
twice. When entering the text, all available characters for this key are displayed. After a short while, the character in focus is displayed in the input
field.
To speed up the input, you can confirm your entry by pressing "g"
on the navigator after you have selected the required character.
To enter a digit in an alphanumerical input field, press the relevant
key and hold it down. You no longer need to scroll through the entire
list of possible characters.
Character overview (depends on the current language setting)
Key
1x
2x
1
]
1
a
b
c
2
d
e
f
3
g
h
i
4
j
k
l
5
6 m
n
o
6
ö
p
q
r
s
7
t
u
v
8
ü
9 w
x
y
z
9
2
3
4
5
7
8
0
(
3x
4x 5x 6x
ä
ß
0
[1]
[2]
[1] Next letter in upper case (active for maximum one second)
[2] Switch to digit input
) .
,
? !
’
"
-
(
)
@ /
:
_
23
Getting to know your OpenStage phone
Multi-function keys
Key Function during text input
) Write special characters
Function when held down
Deactivate the ring tone
between upper and
Activate the telephone lock.
( Switch
lower case
Alphabetic labeling of dial keys is also useful when entering vanity numbers (letters associated with the phone number’s digits as indicated on the
telephone spell a name, e.g. 0700 - PATTERN = 0700 - 7288376).
Text editor
A function menu appears under the character selection field in certain situations (such as, when labeling programmable sensor keys). You can enter
punctuation marks and special characters and switch between the entry of
alphanumeric characters in lower and upper case and straightforward digit
entry.
You can select further editor functions via the click wheel:
• OK – Confirm and terminate the entire input
• Cancel – Cancel your entries without saving
• Mode Configuration via the key (
– 123 (# -> ABC) – Numerical entry
– ABC (# -> Abc) – Upper-case characters
– Abc (# -> abc) – Initial character upper case
– abc (# -> 123) – Lower-case characters
• Move cursor left to add or delete characters
• Move cursor right to add or delete characters
• Copy – Copy a visible character string
• Paste – Insert a copied a character string at a cursor position
24
Getting to know your OpenStage phone
Display
Your OpenStage 40 comes with a tilt-and-swivel black-and-white LCD display. Adjust the tilt and contrast to suit your needs (Æ page 144).
Idle mode
If there are no calls taking place or settings being made, your
OpenStage 40 is in idle mode.
Status bar
10:29 am
Mon 17.11.06
Level 2
Mirea, Ch.
S
07
Toussaint.
Rüscher
Programmable sensor
key list Æ page 25
Context-dependent
displays Æ page 26
Stahl, Ing
01234567
Iller, Zin
Own phone number
The left area contains the status bar on the first line and is followed by a
five-line field for comprehensive context-specific displays. The right area is
used for labeling the programmable sensor keys.
Idle-display view and icons
The time, weekday, and date are displayed in the status bar.
In addition, different icons represent different situations and switches:
Icon
Explanation
The ring tone is deactivated.
The "Do not disturb" function is activated.
The phone lock is activated.
A mobile user is logged on to the telephone.
The microphone is deactivated.
25
Getting to know your OpenStage phone
Context-dependent displays
Depending on the situation at hand, the graphic display on your OpenStage
phone displays different content, to which you can respond intuitively.
Information on actual events
The following icons appear centered on the display when your phone is idle
and signal current properties or events.
Example: You missed two calls in your absence.
02
You have two new voice messages that you can open by pressing O
Æ page 30.
Icons for events
Icon
Explanation
Callback requests are active.
You received new voice messages.
New entries have been added to the call lists.
Local call forwarding is active.
Context menus
An arrow beside a selected entry indicates the existence of a context
menu that you can open by pressing the i or g buttons on the navigator
(Æ page 19). The range of functions available is situation-specific.
Consultation
Hold
Blind transfer call
Disconnect
26
1st entry
(selected on callup)
Selected entry
Getting to know your OpenStage phone
Idle display context menu
The following functions (where released) can be accessed by pressing the
right key on the navigator:
Redial {1} 1234
Ringer off
Do not disturb off
Mobile logon
Cancel call backs
First entry (selected when you call
up the menu, if you have already
dialed a phone number)
Selected entry
Only available when configured to support mobility
Directed pickup
Pop-up menus
In many operating situations, suitable functions or information is offered in
an automatic pop-up window.
Example: You set up a consultation call. The pop-up menu opens and offers
suitable functions for selection with the navigator.
012345|
Level 2
Dial
Mirea, Ch.
Redial {1}
Toussaint.
Retrieve held call
Rüscher
Stahl, Ing
Iller, Zin
A pop-up window automatically closes as soon as you have performed an
action.
To suppress information pop-up windows, press i on the navigator.
27
Getting to know your OpenStage phone
Telephony interface
Single-line view
Additional information is displayed in the telephony interface when your
phone rings, when you dial a number or during a call, for instance.
The same information is available on multi-line telephones for the
selected line in the line overview.
Example:
Icon indicating call status
Smith Michael
{ 3:16
08912345678
Call duration
Current call(s)
Consultation
Hold
Blind transfer call
Disconnect
Context menu with situation-specific
options
Icons for frequent call states
Icon
Explanation
The call is active
The call has been disconnected
You have placed the call on hold (e.g. consultation hold).
Your call partner has placed the call on hold
{
}
The voice connection is secure.
The voice connection is not secure.
Detailed descriptions of the various functions can be found in the
sections "Basic phone functions" Æ page 35 and "Enhanced phone
functions" Æ page 70.
28
Getting to know your OpenStage phone
Multi-line view
Two tabs are displayed on the telephony interface:
• "[My phone]" tab – represents the primary line or the line view of a selected line Æ page 28
• "Overview" tab – configurable overview of the secondary lines
Æ page 21
To access the menu: Press the h key:
Example:
Overview
My phone
Level 2
g Bohr, Nils
My phone
Line busy
Line 1
Line 1
Line 2
Line 2
Line key labeling
Æ page 21
Line status
Line name
Status icon
The status icons provide information about the state of the relevant line.
Icon
Explanation
Call for the corresponding line.
Call from a DSS line.
Call for a line with suppressed ring tone Æ page 115.
"Hold reminder" is activated Æ page 75.
The line is currently not available.
The line is busy.
Please note the LED displays for the line keys Æ page 22.
29
Getting to know your OpenStage phone
Messages
Depending on the type and configuration of your communications platform
(contact the relevant administrator), messages from services, such as,
HiPath Xpressions can be displayed in this list.
When new messages are received, a message appears (Æ page 26) on
the idle display and the LED on the O (Æ page 18) key lights up.
To access the menu: Press the O key and use the navigator to select
and confirm the relevant submenu.
Records
Messages
Calls
Voicemail
You will find voicemails in the Messages directory.
Messages Directory:
The following default entry appears in the list: Voice mail
Voice mail
No new messages
Alternative call: Hold down the O key.
If your system is appropriately configured (contact the relevant administrator), you can call the voice mailbox directly and immediately play back the
messages saved.
30
Getting to know your OpenStage phone
Calls
This list appears as soon as you receive new missed calls if you select the
option Calls in the Records menu. You can then scroll back to the Calls
menu with the backspace key. The following calls or call attempts are
logged as call lists:
Calls
Missed
Dialled
Received
Forwarded
The number of missed calls and unchecked calls is shown on the idle display.
Call lists
All calls to your phone are time-stamped and logged in consecutive order
in the call lists.
Each call list may contain up to 30 entries. Once this limit is reached, the
oldest entry in the log is deleted.
Multiple calls from the same number are only listed once. The number of
call attempts is logged in the "Details" context menu and additionally in the
"Missed Calls" log in the list display.
The list contains the phone number as well as the time of the last call.
Callers with suppressed numbers are listed as "Unknown" in the call
lists.
Only calls to the primary line are received on multi-line phones
(Æ page 12).
31
Getting to know your OpenStage phone
Example of the Missed call list:
Missed
Options g
(Busch, Wilhelm
11178
(Benz, Karlg
235689
(Lessing, Ephraim
2568900
Time of call
12:11
(2)
Number of call attempts
10:25
Selected new entry with
context menu
(1)
7:22
Old entry
(1)
Call list options
You can select the following function in the Options context menu:
Delete all Æ page 95
Entry-specific context menu
You can select the following functions for an individual entry:
• Dial Æ page 86
• Details Æ page 95
Call attempts with date and time (up to ten can be saved)
• Delete Æ page 95
32
Getting to know your OpenStage phone
Program/Service menu
You can make settings here and use this menu to navigate to the password-protected administration area.
To access the menu: Press the N key and use the navigator to select
and confirm the relevant menu.
Settings
User
Settings for the user
Admin
Password-protected
administration area
User settings
You can use the "User" menu to make local function settings for your OpenStage and to configure the appearance of your display to your personal requirements.
Select one of the following menus with the navigator (Æ page 19):
• "Date and time" Æ page 146
• "Audio" Æ page 150
• "Configuration" e.g. Æ page 71 or Æ page 91
• "Phone" Æ page 64 Æ page 144
• "Locality" Æ page 146
• "Security" Æ page 119
• "Network information" Æ page 34
• "Reset" Æ page 69
33
Getting to know your OpenStage phone
Network information
V
Information about the IP address or name which was assigned to the
phone in the network and therefore the HTML address of the web interface.
View information on the phone Æ page 160
Contact your service personnel or refer to the OpenStage Administration Manual for more on the network information values listed
here.
Perform reset
V Personal settings made via the telephone menu or the web interface can
be reset to factory settings.Æ page 161
Administration
You can access the administration area via the "Admin" function and by entering the administration password.
Refer to the administration manual supplied with your phone for more detailed information on this topic.
Control and monitoring function
A control or monitoring function can be activated on your phone for service
purposes by remote maintenance.
Control function
Service personnel have the option to activate and deactivate features of
the phone via remote maintenance. During maintenance the handset, microphone, loudspeaker and headset are deactivated. You are additionally
informed on the display that the control function is active.
Monitoring function
In order to detect malfunctioning of a phone for example, the service personnel install a monitoring function. You can use your phone as normal during monitoring. However you will first be informed about the operation
with a message on the display and prompted to allow monitoring.
If service personnel have activated a function on your phone, which continuously transmits operating data to a server, you will see the flashing
icon
in the upper display line.
34
Basic functions
Step by Step
Basic functions
Please read carefully the introductory chapter
"Getting to know your OpenStage phone"
Æ page 13 before performing any of the steps
described here on your phone.
Secure voice transmission
Prerequisite: The secure voice communication option
must be activated by your administrator.
If you call a party or receive a call from a party over a secure connection, a padlock icon1 appears on the other
party’s row on your graphic display. You can opt to have
voice connections that are no longer secure indicated
by a brief alerting tone and a window with the message
"Unencrypted call" (see Æ page 156).
Answering a call
Your OpenStage phone rings with the tone signal set
when an incoming call is received. The call is also visually signaled on the call display.
If transmitted, calling party information (name, phone
number) appears on the graphic display.
If you have set a pattern melody or a ringtone file
Æ page 152 on your phone, it is possible that
service personnel have preset a different pattern
melody, pattern sequence or ringtone or deactivated the ringtone, depending on the call type
(e.g. an external or internal call).
An incoming call will interrupt any ongoing telephone setting operations. When the call ends, you
can press the N key to return to the point in the
menu structure where you were interrupted.
1.
Closed for secure or open for nonsecure voice communication
35
Basic functions
Step by Step
Answering a call via the handset
The phone rings. The caller is displayed.
^ Lift the handset.
if nec. +- Set the call volume.
Answering a call via the loudspeaker
(speakerphone mode)
The phone rings. The caller is displayed.
The pop-up menu opens:
Select and confirm the option shown. The n key
lights up.
Accept?
or
n Press the key shown. The key lights up.
The speakerphone function is activated.
if nec. +- Set the call volume.
Suggestions for using speakerphone mode:
• Tell the other party that speakerphone mode is active.
• Adjust the call volume while speakerphone mode is
active.
• The ideal distance between the user and the phone
in speakerphone mode is 50 cm.
36
Basic functions
Step by Step
Accepting a call via the headset
Prerequisite: A headset is connected.
Make sure your headset port is set up properly
Æ page 155.
The phone rings. The o key flashes.
o Press the key shown.
if nec. +- Set the call volume.
Answering calls automatically via the headset
S
Prerequisite: The service personnel have additionally
configured a key with the "Auto-Headset function (AICS
Zip tone) (Æ page 64).
Press the "Auto-Headset" sensor key to activate automatic call answering. This key and the headset key illuminate.
A short acoustic signal is heard on the headset for a call
and the connection is established.
If you want to manually answer calls again, deactivate
the automatic answering function using the "AutoHeadset" key. Both keys are off.
37
Basic functions
Step by Step
Directed pickup
You can pick up a call signaled at an absent coworker’s
phone. If a colleague has placed a call on hold on their
multi-line phone you can also pick up this call.
Picking up call
Prerequisite: You know the coworker’s internal phone
number and the function is configured for you in OpenScape Voice.
A coworker’s phone rings.
Directed pickup?
Select and confirm the option shown in the idle phone’s
context menu.
or
^ Lift the handset.
or
n Press the key shown.
Directed pickup?
Select and confirm the option shown.
j Enter and confirm the relevant phone’s internal num-
ber.You are connected to the calling party either via the
handset or in speakerphone mode.
38
Basic functions
Step by Step
Picking up the held call:
Prerequisite: Your colleague has placed a call on hold
on their multi-line phoneÆ page 100. You know the coworker’s internal phone number and the function is configured for you in OpenScape Voice.
Directed pickup?
f
Select and confirm the option shown in the idle phone’s
context menu.
or
^ Lift the handset.
or
n Press the key shown.
Directed pickup?
f
Select and confirm the option shown.
j Enter and confirm the relevant phone’s internal number.
You are connected to your colleague’s held call either via
the handset or in speakerphone mode.
39
Basic functions
Step by Step
Switching from handset to speakerphone mode
Make note of the two different processes and activate, if necessary, your preferred setting
Æ page 154.
Prerequisite: You are conducting a call via the handset
and the microphone and loudspeaker functions have
been activated by administrator.
Standard mode
n and \ Hold down the key and replace the handset. Then release the key and proceed with your call.
US mode
If the country setting is set to US, you do not have to
hold down the loudspeaker key when replacing the
handset to switch to speakerphone mode.
n Press the key shown.
\ Replace the handset. Proceed with your call.
{ or }
40
A secure voice communication is indicated by a
closed padlock icon on the graphic display; a nonsecure voice communication is indicated by an
open padlock icon on the graphic display (see
also Æ page 35)
Basic functions
Step by Step
Switching from speakerphone mode to
the handset
Prerequisite: You are conducting a call in speakerphone mode.
^ Lift the handset.
n The key shown goes out.
41
Basic functions
Step by Step
Switching from headset to speakerphone mode
In standard mode
n Press and hold the key (open listening ist activated),
o Press the key shown. Speakerphone mode is activated.
In U.S. mode
n Press the key shown.
o Press the key shown. Speakerphone mode is activated.
Open listening
You can let other people in the room join in on the call.
Let the other party know that you have turned on the
loudspeaker.
Prerequisite: You are conducting a call via the handset.
Activating
n Press the key shown.
Deactivating
n Press the lit key.
Switching to speakerphone mode
n \ Hold down the lit key and replace the handset.
42
Basic functions
Step by Step
Activating/deactivating the microphone
You can temporarily switch off the handset microphone
to prevent the other party from listening in while you
consult with someone in your office.
Prerequisite: You are conducting a call.
Deactivating the microphone
p Press the key shown.
Activating the microphone
p Press the lit key.
Ending a call
s Press the key shown.
or
Disconnect?
Select and confirm the option shown in the connections’s context menu.
or
\ Lit key pressed
or In speakerphone mode
n Press the lit key.
43
Basic functions
Step by Step
Group call
Your administrator can incorporate multiple telephones
in a call pickup group. If your telephone belongs to a
pickup group, you can also accept calls intended for other members of the group.
A group call is displayed on the phone. Service personnel may have made the following settings for signaling:
Telephone status
Ring on group
call = Yes
Ringing on group
call = No
Ringtone
on
Ringtone
Loudspeaker
Beep
Loudspeaker
Handset
Ringtone
Loudspeaker
Beep
Handset
Handset
Open listening
Beep
Handset and
loudspeaker
Beep
Handset and loudspeaker
Headset
Ringtone
Loudspeaker
Beep
Headset
Headset
Open listening
Beep
Headset and
loudspeaker
Beep
Headset and loudspeaker
Speakerphone mode
Beep
Loudspeaker
Beep
Loudspeaker
Silent
in
Connection
Ringetone
off
Silent
in
Connection
Nothing
Nothing
Handset
Nothing
Beep
Handset
Handset
Open listening
Beep
Handset and
loudspeaker
Beep
Handset and loudspeaker
Headset
Nothing
Beep
Headset
Headset
Open listening
Beep
Headset and
loudspeaker
Beep
Headset and loudspeaker
Speakerphone mode
Beep
Loudspeaker
Beep
Loudspeaker
The volume settings can be found from Æ page 150.
44
Basic functions
Step by Step
Further service personnel settings for group calls:
• The group call can be picked up both by lifting the
handset and via the "Pickup call" menu option.
• The group call be picked up via the "Pickup call"
menu option but not by just lifting the handset.
• A key is programmed for call pickup.
A group call is waiting and is indicated on the display by
Pickup: Caller
for: Party
Picking up a group call
The pop-up menu opens:
Pickup call?
Confirm the option shown.
or
^ Lift the handset (only if the appropriate function is set
by your administrator)
or
R Press the sensor key programmed with the "Call pickup"
function (if configured). The speakerphone function is
activated.
Ignoring a group call
Ignore?
Select and confirm the option shown. The phone stops
signaling the group call.
45
Basic functions
Step by Step
Making calls
If you selected the option "Busy When Dialing"
Æ page 89, you will not be interrupted by an incoming call. In this case, the caller hears the busy
signal.
Off-hook dialing
^ Lift the handset.
j Enter the number if nec. Use the navigator Æ page 19
to correct entries.
In the pop-up menu:
Dial
Confirm or wait until the dial delay expires. (see
Æ page 87).
or In the pop-up menu:
Redial {1} S. Hawking
Select and confirm the option shown.
The connection is set up.
If you are using a dial plan and Immediate dialing is set (see Æ page 48, dialing is automatically performed as soon as the character string entered matches an entry in the dial plan.
46
Basic functions
Step by Step
On-hook dialing
The connection is set up with on-hook dialing via the
loudspeaker (speakerphone mode) or via a connected
headset.
n Press the key shown.
or
o Press the key if a headset is connected.
j Enter the station number.
i Press or wait until the dial delay expires (see
Æ page 87).
or In the pop-up menu:
Redial {1} S. Hawking
Confirm.
First enter the number
First enter the number. The loudspeaker or headset key
illuminate when you enter the first digit.
j Enter the station number. if nec. Use the navigator
Æ page 19 to correct entries.
Dial
Confirm or wait until the dial delay expires. (see
Æ page 87).
The connection is set up.
If you are using a dial plan and Immediate dialing is set (see Æ page 48, dialing is automatically performed as soon as the character string entered matches an entry in the dial plan.
47
Basic functions
Step by Step
Immediate dialing
Immediate dialing should only be activated if service
personnel has configured and approved a dial plan.
Immediate dialing is deactivated by default. For this reason after entering the number you must either confirm
the "Dial" option or wait until the dial delay expires to set
up the connection. If Immediate dialing is configured,
your call is automatically dialed as soon as the string entered matches an entry in the dial plan.
Activating or deactivating immediate dialing
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j User passwordEnter and confirm the .
Configuration
Select and confirm the option shown.
Outgoing calls
Select and confirm the option shown.
Immediate dialling
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context menu.
Save & Exit
Confirm the option shown
48
Basic functions
Step by Step
Dialing using the hot or warm line function
Your service personnel can configure a hot or warm line
for your phone.
If you lift the handset of the phone or press the loudspeaker key
• with a hot line immediately or
• with a warm line after a defined period of time,
a number specified by service personnel is dialed.
Examples:
• The phone in the lift immediately dials the reception
number.
• The phone at a patient’s bed dials the ward number
e.g. after a minute if no other number is dialed.
49
Basic functions
Step by Step
Redial
Redialing from the call list
Only calls to the primary line are received on
multi-line phones (Æ page 12).
, Press the key shown.
You are automatically directed to the Dialed list in the
Calls menu.
Niels, Bohr
07:06 am
Select and confirm the entry you want.
The phone number associated with the list entry is dialed.
Redialing from the pop-up menu
^ Lift the handset.
or
n Press the key shown.
Redial {1} S. Hawking
Select and confirm the option shown.
The last phone number entered is dialed.
Redialing from the idle menu
Redial {1} S. Hawking
Select and confirm from the idle display context menu
(Æ page 27). The last phone number entered is dialed.
{ or }
50
A secure voice communication is indicated by a
closed padlock icon on the graphic display; a nonsecure voice communication is indicated by an
open padlock icon on the graphic display (see
also Æ page 35).
Basic functions
Step by Step
Consulting a second party
You can call a second party while a call is in progress.
The connection to the first party is placed on hold.
Prerequisite: You are conducting a call.
Consult
Select and confirm the option shown in the connections’s context menu.
j Call the second party.
If you are using a dial plan and Immediate dialing is set (see Æ page 48, dialing is automatically performed as soon as the character string entered matches an entry in the dial plan.
Ending or canceling a consultation call
Disconnect & return
Select and confirm the option shown in the second party’s context menu.
The consultation call is disconnected. The call with the
first party is resumed.
Ending the first call
Disconnect
Select and confirm the option shown in the first call’s
context menu.
The connection to the second party remains active.
If the called party does not answer
In the pop-up menu:
Disconnect & return
Select and confirm the option shown.
The call with the first party is resumed.
51
Basic functions
Step by Step
Switching to the held party (alternating)
Prerequisite: You are conducting a consultation call.
Alternate?
Select and confirm the option shown in the connection’s context menu.
It does not matter which context menu is open
when alternating. The "Alternate" function appears in both menus (active and passive connection).
You can switch back and forth between two subscribers by repeatedly selecting and confirming
"Alternate".
Ending an alternate operation
Disconnecting the held call:
Disconnect?
Select and confirm the option shown in the held connection’s context menu.
The held call is disconnected. The active call continues.
Disconnecting the active call:
Disconnect & return?
52
Select and confirm the option shown in the active connection’s context menu.
The active call is disconnected. The held call remains on
hold and can be managed via the context menu.
Basic functions
Step by Step
Connecting parties
You can connect the first party with the party you consulted, clearing down your connection to both parties in
the process.
Prerequisite: You are conducting a consultation call
Æ page 51 and call joining must be allowed Æ page 53.
Complete Xfer?
Select and confirm the option shown in the active connection’s context menu.
The active and held calls are joined. The active call and
the consultation call are cleared down.
or Connect by hanging up
] or n Replace the handset or, if you are in speakerphone
mode, press the loudspeaker key. The other two parties
are now connected to one another.
Allowing call joining
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Connected calls
Select and confirm the option shown.
Allow call joining = Yes
f
Select and confirm the option shown.
Yes
l
Select and confirm the option shown in the context menu.
Option = Save & Exit
l
Confirm the option shown.
53
Basic functions
Step by Step
Call forwarding
You can forward calls for your phone to another phone.
On multi-line telephones (Æ page 12), you can
only configure call forwarding for the primary
line.
Three forwarding conditions can be programmed in the
forwarding menu:
• All Calls
• Busy
• No reply
Because of its direct impact, "All Calls" call forwarding
has the highest priority followed by "No reply" and
"Busy".
If active, "All Calls" call forwarding is indicated on the
graphic display when the phone is idle.
Forwarded calls can be logged in a call list (see
Æ page 31).
There are three Destination options in the Edit call forwarding menu. These destination options are assigned
to the forwarding types.
All calls (off/on)
Destination
Busy (off/on)
Destination
No reply (off/on)
Destination
One phone number may already be assigned to each
destination. The Destination option could then be Destination 12345, for instance.
54
Basic functions
Step by Step
Programming call forwarding
Configuring destination phone numbers for call
forwarding
You can configure up to five destination phone numbers
for call forwarding. These destination phone numbers
can then be assigned different forwarding types. You
can then enable one of the forwarding types
(Æ page 57).
r Press the key shown.
The pop-up menu opens:
Edit call forwarding
Select and confirm the option shown.
An overview of call forwarding settings appears.
You can also enter the call forwarding settings via
the user menu (Æ page 72).
Destination
Select the destination option for one of the following
forwarding types:
• All calls
• Busy
• No reply
Confirm the destination selected.
You can use each of the three Destination options to save destination phone numbers for the
relevant forwarding type.
Edit favourites
Select and confirm the option shown in the context
menu.
Destination 1
Select and confirm the option shown.
j Enter and confirm the destination phone number.
Define additional destination phone numbers for destination 2 to 5, as necessary.
Save & Exit
Select and confirm the option shown.
Assigning a destination phone number to a call
forwarding type
r Press the key shown.
55
Basic functions
Step by Step
The pop-up menu opens:
Edit call forwarding
Select and confirm the option shown.
An overview of call forwarding settings appears.
Destination
Select the destination option for one of the following
forwarding types:
• All calls
• Busy
• No reply
Confirm the destination selected.
08972228596
Select and confirm a destination number from the list.
Save & Exit
Select and confirm the option shown.
Defining the ring duration before call forwarding on
no reply
You can define how often the phone should ring before
the "No reply" form of call forwarding activates.
This setting is only available if the "Server features" function was deactivated by the administrator.
z You can also configure this setting via the Web interface
Æ page 162.
Prerequisite: The phone is idle.
r Press the key shown.
The pop-up menu opens:
Edit call forwarding
Select and confirm the option shown.
An overview of call forwarding settings appears.
Duration
Select and confirm the option shown.
j Enter a value for the duration.
Save & Exit
56
Select and confirm the option shown.
Basic functions
Step by Step
Activating/deactivating call forwarding
z You can also configure this setting via the Web interface
Æ page 162.
Prerequisite: At least one destination phone number is
programmed (Æ page 55).
r Press the key shown.
The pop-up menu opens:
Edit call forwarding
Select and confirm the option shown.
An overview of call forwarding settings appears.
All calls
Select and confirm the option shown.
or
Busy
Select and confirm the option shown.
or
No reply
Select and confirm the option shown.
On
Select and confirm "On" or "Off" in the context menu.
Save & Exit
Select and confirm the option shown.
57
Basic functions
Step by Step
Activating call forwarding for all calls
Use the r function key to activate call forwarding for
all calls.
z You can also configure this setting via the Web interface
Æ page 162.
Prerequisite: There is at least one forwarding destination programmed Æ page 55.
r Press the key shown.
The pop-up menu opens:
Select and confirm the option shown. The r key
lights up. Call forwarding is activated.
Accept
If the phone is idle, the call forwarding icon K appears
on the graphic display with the destination phone number.
Deactivating call forwarding for all calls
r Press the lit key.
The pop-up menu opens:
The pop-up menu disappears after around five seconds
and the r key goes out.
or
Accept
58
Select and confirm the option shown.
Call forwarding is deactivated.
Basic functions
Step by Step
Call forwarding chain
Sometimes calls to a station are forwarded to another
station which also has call forwarding or DND activated.
This can create a call forwarding chain consisting of several telephones where the last member of the chain is
your phone.
A popup window opens on your phone’s screen with
the following information:
• Who is calling
• Who forwarded first or last.
• The reason for the forwarding is displayed by an
icon.
You can set whether the station that forwarded first or
last is displayed (see Æ page 73).
59
Basic functions
Step by Step
Callback
You can request a callback if the station called is busy or
if nobody answers.
You receive a callback when the other party’s line becomes free.
This option must be activated by your administrator.
On multi-line telephones Æ page 12, only the
callback requests for your primary line are
logged.
Requesting callback
Prerequisite: The station called is busy or nobody answers.
In the pop-up menu:
Call back?
Select and confirm the option shown.
Deleting callback requests
You can delete scheduled callback requests if you no
longer need to return a call, for example, at the end of
the working day.
Prerequisite: At least one callback was requested.
Cancel call backs?
Disconnect?
60
Select and confirm the option shown in the idle display
(Æ page 27) context menu.
m
Confirm in the pop-up menu. All callback requests are
deleted.
Basic functions
Step by Step
Responding to a callback
Prerequisite: A callback was requested. Your phone
rings and station information appears on the graphic display with the callback icon.
The pop-up menu opens:
Accepting a callback
Accept?
Select and confirm the option shown.
Rejecting a callback
Reject?
Select and confirm the option shown.
The callback request is deleted. The caller hears the
busy signal. The caller’s phone number is added to the
missed calls list.
Forwarding a callback
Deflect
Select and confirm the option shown.
j Enter and confirm the phone number.
61
Basic functions
Step by Step
Permitting callback on busy/no reply
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Outgoing calls
Select and confirm the option shown.
Callback: busy
Select and confirm the option shown.
or
Callback: no reply
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Select and confirm the option shown.
62
Basic functions
Step by Step
Calling back missed calls
Calls received while you are absent are indicated by a
message on the idle display (Æ page 26). The O
function key also lights up.
Missed calls are logged in the missed calls list. This list
provides information on the missed call and lets you call
back the number directly (call lists, see also
Æ page 31).
On multi-line telephones Æ page 12, only the
calls missed on your primary line are logged.
O Press the key shown.
Calls
Niels, Bohr
Select and confirm the option shown.
20.05
10:06
Select and confirm the appropriate list entry. The phone
number associated with the list entry is dialed.
If no new calls are listed, the call list menu is offered under Calls Æ page 95.
63
Programming sensor keys
Step by Step
Programming sensor keys
The phone features a range of functions that can, if required, be stored on programmable sensor keys.
The phone comes with six programmable sensor keys,
all of which can be programmed on two separate
levels.
The "Shifted" programmable sensor key, which allows
you to switch between the two programmable sensor
key levels, is preassigned. This programmable sensor
key should be maintained where possible so you can
switch between the two programmable sensor key levels.
The labels for the programmable sensor keys are displayed on the right side of the display.
The programmable sensor keys can also be programmed via the Web interface (Æ page 162).
List of available functions
1. Delete (not assigned)
2. Selected dialling
3. Repeat dialling
4. Forward all calls
5. Forward no reply
6. Forward busy
7. Ringer off
8. Hold
9. Alternate
10. Blind transfer call
11. Transfer call
12. Deflecting
13. Shift
14. Conference
15. Headset
16. Do not disturb
64
17. Group pickup
18. Repertory dial
19. Feature toggle
20. Mobility
21. Directed pickup
22. Callback
23. Cancel callbacks
24. Consultation
25. DSS
26. Call Waiting toggle
27. Immediate ring
28. Preview
29. AICS Zip tone
30. Server feature
31. Start application
32. Send URL
Programming sensor keys
Step by Step
Programming programmable sensor
keys
S Press the sensor key you want to program until the field
opens. The programmable sensor key lights up.
z You can also configure this setting via the Web interface
Æ page 162.
or You can also program keys via the user menu.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Phone
Select and confirm the option shown.
Program keys
Select and confirm the option shown. You are prompted
to press the key you wish to program.
S Press the sensor key you want to program until the field
opens. The programmable sensor key lights up.
Normal
Select and confirm the option shown to program the
first level.
or
Shifted
Select and confirm the option shown to program the
second level.
Do not disturb
Select and confirm the required function in the list (for
instance Do not disturb).
Label
Select and confirm the option shown if you want to
change the label on the graphic display.
j Enter and confirm the label you want.
Save & Exit
Select and confirm the option shown.
65
Programming sensor keys
Step by Step
Programming enhanced functions
Repertory dial
S Press the sensor key you want to program until the field
opens. The programmable sensor key lights up.
z You can also configure this setting via the Web interface
Æ page 162.
Normal
Select and confirm the option shown to program the
first level for instance.
Repertory dial
Select and confirm the function in the context menu.
Label
Select and confirm the option shown if you want to
change the label on the graphic display.
j Enter and confirm the label you want.
Setting
Select and confirm this option to enter a destination
phone number.
j Enter and confirm a stations’s destination phone number.
You can select and insert special characters in the dialing sequence:
« Clear call
~ Make consultation
» Make normal call
¬ Pause
The pop-up menu also offers the following functions:
• Move cursor right and left
• Copy
• Paste
• Mode selection
• Cancel
• OK
Save & Exit
Select and confirm the option shown.
The repertory dial can be up to 40 characters
long.
66
Programming sensor keys
Step by Step
Feature toggle
Only available for Hunt group functions (Æ page 135).
S Press the sensor key you want to program until the field
opens. The programmable sensor key lights up.
z You can also configure this setting via the Web interface
Æ page 162.
Normal
Select and confirm the option shown to program the
first level for instance.
Feature toggle
Select and confirm the function in the context menu.
Label
Select and confirm if you want to change the key label.
j Enter and confirm the label you want.
Setting
Select and confirm this option to enter a code.
j Enter and confirm the code, for example: *96 (contact
your administrator).
Save & Exit
Select and confirm the option shown.
Forwarding
S Press the sensor key you want to program until the field
opens. The programmable sensor key lights up.
z You can also configure this setting via the Web interface
Æ page 162.
Normal
Select and confirm the option shown to program the
first level for instance.
Forward all calls
Select a forwarding type:
• Forward all calls
• Forward no reply
• Forward busy
Select and confirm the function in the context menu.
Label
Select and confirm the option shown if you want to
change the label on the graphic display.
j Accept or edit the label and confirm.
Setting
Select and confirm this option to enter the forwarding
destination.
67
Programming sensor keys
Step by Step
j Enter and confirm the phone number of the forwarding
destination.
Save & Exit
Select and confirm the option shown.
Immediate ring
This function allows you to switch the preset delay
(Æ page 112) on and off for all line keys.
Activate/deactivate call waiting
You can press a key to activate or deactivate call waiting
functionality, even during a call. This requires that call
waiting is permitted in principle (Æ page 79) and that
the key has been configured(Æ page 68).
Using sensor keys
The use of programmed functions depends on the phone’s status. The relevant display appears once you have
pressed a sensor key.
Example 1: Accessing a stored contact or
phone number
Prerequisite: The idle menu is displayed on the graphic
display.
S Press sensor key for stored contact. Connection setup
is shown in the display.
Example 2: Deactivate call waiting
S Press "Call waiting on" sensor key. The sensor key lights
up.
The second call function is deactivated. The call is rejected or forwarded.
68
Programming sensor keys
Step by Step
Resetting programmable sensor keys
You can reset sensor keys you configured to factory settings (see also Æ page 161).
N Press the key shown.
User
Confirm the option shown.
if nec. j Enter and confirm the user password.
Reset
Select and confirm the option shown to switch to the
Reset.user.data menu.
Function key data
Select the option shown.
Yes
Select and confirm the option shown in the context
menu to delete the content of all sensor keys.
Perform reset
Select and confirm "Reset selected user data." The contents of the sensor keys you configured are deleted.
Sensor keys which can only be configured by service personnel remain unchanged
69
Enhanced phone functions
Step by Step
Enhanced phone functions
Incoming calls
Accepting calls via the headset
Prerequisite: The headset is connected.
o The LED flashes when a call is received.
Press the key shown. Conduct call.
Ending the call:
o Press the key shown. The LED goes out.
Deflecting a call
Using call deflection
Prerequisite: An incoming call is displayed or signaled.
In the pop-up menu:
Deflect
Select and confirm the option shown.
The call is immediately deflected if a destination phone
number is programmed (Æ page 71).
or If you did not set a phone number when programming
call deflection, a pop-up menu appears prompting you
to enter a destination phone number for call deflection.
j Enter and confirm the destination phone number.
The call is deflected.
70
Enhanced phone functions
Step by Step
Permitting call deflection
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Incoming calls
Select and confirm the option shown.
Deflecting
Select and confirm the option shown.
Allow deflection
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Default destination
Select and confirm the option shown.
j Enter and confirm the phone number to which the station should be deflected.
Entering a destination phone number is not mandatory when call deflection is active. If you want
to deflect an incoming call, you are prompted to
enter a destination phone number if there is
none stored.
or Deflecting to a DSS number
A call can be deflected to a direct station selection
(DSS) subscriber using the DSS key, if the key is configured and the deflect function is activated by your administrator Æ page 104.
Deflect to DSS
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Select and confirm the option shown.
71
Enhanced phone functions
Step by Step
Rejecting a call
You can reject an incoming call.
In the pop-up menu:
Reject
Select and confirm the option shown.
The caller hears a busy signal.
If the rejected caller’s phone number is transmitted, it is saved in the call list. You can then call
this party back at a later time.
Configuring call forwarding
You can also enter the call forwarding settings via
the Forwarding key (Æ page 55).
N Press the key shown until "Menu" is active.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Incoming calls
Select and confirm the option shown.
Forwarding
Select and confirm the option shown.
For a description of the settings, see the chapter "Call
forwarding" (Æ page 54).
Configuring call forwarding
Settings
Select and confirm the option shown.
For a description of the settings, see the chapter "Call
forwarding" (Æ page 54).
72
Enhanced phone functions
Step by Step
Setting alerts
Use the Call forward alerts menu to enable and disable
visual and audible alerts for call forwarding (not possible
with the Forwarding key).
Alerts
Select and confirm the option shown.
Visual alerts= No
Select the option shown.
Yes
Select and confirm the option shown in the Yes/No context menu.
or
Audible alerts= No
Select the option shown.
Yes
Select and confirm the option shown in the Yes/No context menu.
or
Forwarding station... Last
Select the option shown.
Display last
Select and confirm Display last/Display first
Option = Save & Exit
Select and confirm the option shown.
73
Enhanced phone functions
Step by Step
Placing a call on hold
You can use this function to place an ongoing call on
hold, for instance, to prevent the other party overhearing a conversation with a colleague in the same room.
The "Hold" function must be activated by the administrator.
Prerequisite: You are conducting a call.
Hold
Select and confirm the option shown in the connections’s context menu.
Retrieving a held call:
Reconnect
Select and confirm the option shown in the connections’s context menu.
Using line keys
On multi-line telephones you can use the line keys to
place ongoing calls on hold.
R Press the corresponding trunk key. The line key LED
starts flickering. The call is now on hold.
Retrieving a held call:
T Press the corresponding trunk key. The line key LED
lights up. The call is retrieved.
The LED display Æ page 22 or status display on
the "Overview" tab Æ page 29 indicates to other
multi-line telephones on which this line is also
configured, that the call is on hold. These phones
can then pick up the call.
Held call wait status
After placing a call on hold, you can replace the handset
and then decide if the call should be retrieved or disconnected.
Prerequisite: You placed a call on hold and replaced the
handset.
In the pop-up menu:
Retrieve held call
Select and confirm the option shown to resume the call
in speakerphone mode.
or
Disconnect
74
Select and confirm the option shown to disconnect the
call.
Enhanced phone functions
Step by Step
Activating/deactivating the hold reminder tone
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Connected calls?
Select and confirm the option shown.
Allow hold rem.?
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Select and confirm the option shown.
Setting the hold reminder time
Use the "Hold reminder" function to set the length of
the timeout before an automatic reminder is issued
about a held call.
The minimum value is 1, that is, the reminder is output
after one minute. The maximum value is 99 minutes.
Press 0 to deactivate the reminder.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Connected calls?
Select and confirm the option shown.
Hold rem. delay
Select and confirm the option shown.
75
Enhanced phone functions
Step by Step
j Enter a value between 3 and 15 and confirm.
Save & Exit
Select and confirm the option shown.
Music on hold
Music on hold is played back when you are placed on
hold by another party, providing this option is active.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Connected calls
Select and confirm the option shown.
Music on hold
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Select and confirm the option shown.
76
Enhanced phone functions
Step by Step
Call waiting (second call)
You can accept a second incoming call in the course of
an ongoing call. The caller hears the on-hook signal
while you hear a call-waiting signal tone.
You can ignore or accept the second call. Before you accept the second call, you can end the first call or place
it on hold for subsequent retrieval.
You can block the second call or the signal tone
(Æ page 79).
Accepting a second call
Prerequisite: You are conducting a call and call waiting
is allowed (Æ page 79).
In the pop-up menu:
Accept
Select and confirm the option shown.
You can talk to the second party.
The connection to the first party is on hold.
You can still
• toggle between an initial and second call or
• initiate a conference
Consultation call from second call
If the second call is your active call you can initiate a
consultation call from it.
From a consultation call in the second call you can
• initiate a conference
• toggle between the second call and a consultation
call
• transfer a call
• disconnect the calls again
During a consultation in the second call, the first call is
parked and can only be unparked when the consultation
or second call ends or these calls were connected.
Disconnect & return
Select and confirm the option shown in the second
call’s context menu. The call to this station is disconnected and the call to the first station is reconnected.
Ignoring second call
Prerequisite: You are conducting a call and call waiting
is allowed (Æ page 79).
In the pop-up menu:
77
Enhanced phone functions
Step by Step
Ignore
Select and confirm the option shown.
The caller still hears the on-hook signal. You can subsequently Accept, Reject or Deflect the second call.
While the ignored second call continues to wait, from
the active call you can:
• make a consultation call
• initiate a conference
• toggle between the consultation call and your call
party
• transfer a call
A third call would be rejected with the busy signal
If you have disconnected the first call, the ignored second call rings like a normal call.
Rejecting a second call
Prerequisite: You are conducting a call and call waiting
is allowed (Æ page 79).
In the pop-up menu:
Reject
Select and confirm the option shown.
The second call is rejected. The caller hears the busy
signal. The caller’s phone number is added to the
missed calls list.
Deflecting a second call
Prerequisite: You are conducting a call and call waiting
is allowed (Æ page 79).
In the pop-up menu:
Deflect
Select and confirm the option shown.
j Enter and confirm the phone number.
The second call is deflected to the destination specified. You are reconnected with the first party.
Connecting parties
Complete Xfer
78
Select and confirm the option shown in the active connection’s context menu. The other two parties are now
connected to one another. You can now hang up or dial
another number for instance.
Enhanced phone functions
Step by Step
or Connect by hanging up
Prerequisite: Connecting by hanging up is activated
(ask your service personnel) and "Toggle associate"
must be set to "Yes" (Æ page 80). Before you can be
connected by hanging up you must have toggled at
least twice (Æ page 52).
] or n Replace the handset or, if you are in speakerphone
mode, press the loudspeaker key. The other two parties
are now connected to one another.
Allowing call waiting
If the Call waiting (second call) function is deactivated, a caller hears the busy signal if you are already conducting a call.
Prerequisite: The option was programmed by your administrator.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Incoming calls
Select and confirm the option shown.
Handling
Select and confirm the option shown.
Allow call waiting
Select and confirm the option shown.
Yes
Select and confirm the option shown.
Save & Exit
Select and confirm the option shown.
When Allow call waiting is activated, you can toggle
the configured sensor key to switch call waiting on/off
(Æ page 68).
79
Enhanced phone functions
Step by Step
Toggling associate
Set the "Toggle associate" function to Yes if you want to
connect to a second or pickup call by hanging up.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j User passwordEnter and confirm the .
Configuration
Select and confirm the option shown.
Connected calls
Select and confirm the option shown.
Toggling associate
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context menu.
Save & Exit
Select and confirm the option shown.
80
Enhanced phone functions
Step by Step
Transferring a call
You can transfer your current call to another party with
or without consultation.
Blind transfer
Prerequisite: You are conducting a call. The options "Allow call transfer" and "Transfer on ring" were allowed
(Æ page 82).
Blind transfer
Select and confirm the option shown in the connections’s context menu.
j Enter and confirm the phone number of the second party to whom you want to transfer the call.
The graphic display returns to idle following successful transfer.
Transferring with consultation
You can announce a call to a recipient before transferring it.
Prerequisite: You are conducting a call. The options "Allow call transfer" and "Transfer on ring" were allowed
(Æ page 82).
Consultation
Select and confirm the option shown in the connections’s context menu. The call is placed on hold.
j Enter the phone number of the party to whom you want
to transfer the call.
Dial
Confirm the option shown.
If the party answers:
Complete Xfer
Announce the call you want to transfer.
Select and confirm the option shown in the connections’s context menu.
If the party does not answer:
You do not have to wait for the second party to answer
before you can transfer the call.
Complete transfer
Select and confirm the option shown in the connections’s context menu.
or Replace the handset or, if speakerphone mode is active,
press the lit n key to transfer the call.
81
Enhanced phone functions
Step by Step
If the party does not answer, you will be called back by
the first party.
Allowing call transfer
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Connected calls
Select and confirm the option shown.
Allow call transfer
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Select and confirm the option shown.
82
Enhanced phone functions
Step by Step
Allowing "Transfer on Ring"
If this option is allowed, you can activate call transfer by
replacing the handset even before the called party answers.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Outgoing calls
Select and confirm the option shown.
Transfer on ring
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Select and confirm the option shown.
83
Enhanced phone functions
Step by Step
CTI calls
Beep on auto-answer
Speakerphone mode activates automatically on your
phone if you use a CTI application (such as Outlook) to
dial a number when Auto Answer is active. If Auto Answer is not active, the phone rings first and you have to
press the loudspeaker key or lift the handset to set up
the call. This setting also defines whether or not incoming calls are automatically accepted. If the function is
active, an alert beep sounds when an incoming call is
automatically accepted.
Information on the operation of the configured CTI application can be found in the corresponding user guide.
z You can also configure this setting via the Web interface
Æ page 162.
Prerequisite: The option was programmed by your administrator.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Incoming calls
Select and confirm the option shown.
CTI calls
Select and confirm the option shown.
Auto-answer
Select and confirm the option shown.
Yes
Select and confirm the option shown.
Beep on auto-answer
Select and confirm the option shown.
Yes
Select and confirm the option shown.
Save & Exit
Select and confirm the option shown.
84
Enhanced phone functions
Step by Step
Beep on auto-reconnect
You can reconnect a held call both via the CTI application and via the phone. A beep sounds when you toggle
between an active call and a held call when the function
is active.
Prerequisite: The option was programmed by your administrator.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Incoming calls
Select and confirm the option shown.
CTI calls
Select and confirm the option shown.
Beep on auto-unhold
Select and confirm the option shown.
Yes
Select and confirm the option shown.
Save & Exit
Select and confirm the option shown.
85
Enhanced phone functions
Step by Step
Making calls
Dialing with the DDS key
You can program frequently used phone numbers on
programmable keys (Æ page 64). If you press a direct
destination selection key for around three seconds, the
associated contact or phone number appears and dialing is initiated.
Prerequisite: A direct destination key is programmed
Æ page 64.
R Press the programmed DDS key. Dialing is initiated.
Dialing a phone number from a list
The following call lists are available in the "Calls" directory:
• Missed
• Dialed
• Received
• Forwarded
For a detailed description of the call lists, see
Æ page 31.
O Press the key shown.
Calls
Select and confirm the option shown.
Dialed
Select and confirm the required call list.
Niels, Bohr
86
07:06am
Select and confirm the entry you want. The phone number associated with the list entry is dialed.
Enhanced phone functions
Step by Step
Using autodial delay
A number is automatically dialed after a set delay starting from the entry of the number’s last digit. The autodial delay can be used:
• when dialing in idle mode
• when deflecting an incoming call
• Consultation
• when transferring an answered call.
The delay can be reduced by performing one of the following activities:
i • Press the key shown. This always works.
^ • Lift the handset (off-hook). This only works if the
phone number was entered when the phone was
idle or if it was entered for a consultation call when
the handset was off hook.
n • Press the key shown. This only works if the phone
number was entered when the phone was idle and
the loudspeaker key was not lit or if the phone number was entered for a consultation call and the loudspeaker key was not lit.
If an emergency number is preset by your administrator, the autodial delay for this phone number
is reduced to one second.
Automatic dial delay does not work if you are
using a dial plan and Immediate dialing is configured (see Æ page 48). The number is automatically dialed as soon as the string entered matches an entry in the dial plan.
87
Enhanced phone functions
Step by Step
Settings for autodial delay
z You can also configure this setting via the Web interface
Æ page 162.
The setting does not affect automatic emergency
number dialing.
If you select Autodial delay, you must either confirm
the "Dial" option, press the loudspeaker key or wait until
the autodial delay expires to set up a call when dialing
with the handset on hook.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Outgoing calls
Select and confirm the option shown.
Autodial delay
Select and confirm the option shown.
j Specify a value and confirm your entry.
Save & Exit
88
Select and confirm the option shown.
Enhanced phone functions
Step by Step
Allowing "Busy When Dialling"
If you activate this function, an incoming call received
while you are performing dialing is rejected. The caller
then hears the busy signal.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Outgoing calls
Select and confirm the option shown.
Busy when dialling
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Select and confirm the option shown.
This setup option can also be found under "Handling" in the "Incoming calls" menu.
89
Enhanced phone functions
Step by Step
Conference
Local conference
This type of conference is also referred to as a threeparty conference. It involves up to three participants.
Prerequisite: You are conducting a consultation call
Æ page 51 or have accepted a second call Æ page 77,
and the conference function is active Æ page 91.
Initiating a local conference
You can initiate a conference by calling the "Conference" function in the context menu of either
the active or held call.
Conference?
Select and confirm the option shown in the connection’s context menu. You are connected to both parties
at once.
Conducting one-on-one calls
User
Select the connection you want to clear down on the
display.
Disconnect
Select and confirm the option shown in the context
menu. You are now involved in a one-to-one call with the
remaining call party.
{ or }
If you already are involved in a secure connection
with a party when you initiate a consultation call,
the original party is placed on hold. The new consultation connection can be either secure or nonsecure. However, the first connection remains
secure even if all three parties are now joined together in a conference.
The entire conference is nonsecure if the connection to at least one of the parties is not secure
(see also Æ page 35).
The relevant padlock icon appears on the "Conference" row.
90
Enhanced phone functions
Step by Step
Ending a local conference
Allowing call partners to continue a conference after you exit
Prerequisite: The function "Allow join in conference"
(Æ page 92) was activated.
Exit Conf?
Select and confirm the option shown in the "Conference" context menu.
or
] or n Replace the handset or, if you are in speakerphone
mode, press the loudspeaker key. Both call partners remain connected. You are disconnected from the conference call.
Disconnecting a party
End Conf?
Select and confirm any of the connections in the context menu.
Both connections are cleared down – the conference is
cleared down.
Allowing a local conference
This option allows or blocks the "Conference" function.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Connected calls
Select and confirm the option shown.
Allow conferences
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Select and confirm the option shown.
91
Enhanced phone functions
Step by Step
Allowing joining in a local conference
You can use this option to decide whether or not your
call partners are allowed to join calls after you exit the
conference call.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Connected calls
Select and confirm the option shown.
Join in conferences
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Select and confirm the option shown.
92
Enhanced phone functions
Step by Step
System-based conference
This type of conference is also referred to as a large conference. It can include up to ten parties.
Prerequisite: You are conducting a consultation call
Æ page 51 or you have accepted a second call
Æ page 77, and the "centralized conference" feature
was configured by your administrator.
Establishing a conference
Conference?
Select and confirm the option shown in the connection’s context menu. You are connected to the first two
parties at once. The conference is displayed with the
current participants. You can now:
• initiate a consultation call
• put the conference on hold
• leave the conference.
Conducting a consultation call
Consultation?
Select and confirm the option shown in the "Conference" context menu. If the party answers, you can:
• toggle between the party and the conference
• connect the consultation call to another called party
• end the consultation call and return to the conference
• add the consultation call party to the conference.
Adding a party
Prerequisite: You are conducting a consultation call and
the conference is on hold.
Conference?
Select and confirm the option shown in the consultation
call’s context menu. The party is added to the conference. Only the conference and all current participants
are now displayed.
Putting the conference on hold
Hold?
Select and confirm the option shown in the "Conference" context menu. The conference is placed on hold
and you can consult with someone in your office, for instance.
93
Enhanced phone functions
Step by Step
Leaving a conference
Exit Conf?
Select and confirm the option shown in the "Conference" context menu. You are disconnected from the
conference call and can dial another number, for instance. The other call partners remain connected.
{ or }
If using the "centralized conference" option, the
Conference row contains a closed padlock icon
for a secure voice connection and an open padlock icon for a nonsecure voice connection
(Æ page 35).
The display depends on whether the conference
server supports secure voice communication.
The appropriate display is set by the conference
server.
94
Enhanced phone functions
Step by Step
Call lists
For a detailed description of the different call lists, see
Æ page 31.
Editing entries
Selecting an entry
O Press the key shown.
Calls
Select and confirm the option shown.
Missed
For instance, select and confirm the list of missed
callsÆ page 63.
The list is sorted chronologically, with the most recent
caller first.
You can use the navigator to scroll through the list.
Niels, Bohr
22.05
13:22
Select the list entry.
Displaying details
Details
Select and confirm the option shown in the context
menu.
For display and information shown.
Deleting an entry
Delete
Select and confirm the option shown in the context
menu. The entry is deleted.
Deleting all entries
O Press the key shown.
Calls
Select and confirm the option shown.
Dialed
For instance, select and confirm the list of dialed numbers.
Options
Select the option shown.
Delete All
Select and confirm the option shown in the context
menu.
All entries in the list displayed are deleted.
95
Making calls with multiple lines
Step by Step
Making calls with multiple lines
You can use your OpenStage 40 as a multi-line phone.
If you have any questions regarding how to configure
your OpenStage phone as a multi-line phone, please
contact your administrator.
The following is a description of the telephony scenarios for multi-line phones. To facilitate comprehension,
you should familiarize yourself with the enhanced telephony application and how to use the line keys beforehand. Furthermore, you can specify individual settings
for your multi-line telephone. Refer to the following sections for a detailed description of the individual components:
• Introduction to multi-line phones Æ page 12
• Lines and line keys Æ page 21
• Multi-line telephony interface Æ page 29
• Individual settings Æ page 111
Incoming calls
Depending on your individual settings, you will be notified of incoming calls Æ page 152.
Accepting calls for the primary line
In this case, the telephone behaves in the same way as
a single-line telephone. See Æ page 35 and Æ page 70.
Accepting calls for secondary lines
Prerequisite: The secondary line is configured on your
multi-line telephone.
Using the handset
^ Lift the handset.
[ Conduct call.
The line that rings is automatically selected. If
calls are ringing on more than one line, you will
be connected to the line that has been ringing
the longest.
96
Making calls with multiple lines
Step by Step
Using the line keys
T Press the flashing trunk key.
Speakerphone mode.
Accept
Select and confirm the option shown.
Speakerphone mode.
Making calls
You must seize a line before you can make calls on a
multi-line telephone.
Trunk seizure can be configured on an individual basis.
Your administrator can determine if the lines on your
telephone can be automatically seized and with which
priority.
If you have seized a secondary line, this line is
reserved for you for making calls for a specific
period as defined by the administrator. No other
user can seize this line during this period, even
if the line is also assigned to this user’s telephone.
Manual trunk seizure
^ or n or o Lift the handset or press the speakerphone mode or
headset key.
S Press the required trunk key.
or
h Press the key shown to open the Overview tab
Æ page 29.
Line 2
Select and confirm the required line (e.g. line 2). The selected line is displayed on the screen.
j Enter the phone number or use redial, for example. The
connection is set up.
97
Making calls with multiple lines
Step by Step
Automatic trunk seizure
Prerequisite: Your administrator has configured automatic trunk seizure.
^ or n or o Lift the handset or press the speakerphone mode or
headset key.
R The line defined during configuration is seized.
j Enter the station number. The connection is set up.
Dialing the last dialed number
Regardless of the line used, the last number dialed on
your telephone is displayed for redialing in the selected
number’s context menu.
^ or n or o Lift the handset or press the speakerphone mode or
headset key.
S Press the required line key (Æ page 97).
In the pop-up menu:
Redial {1} 12345
Confirm the option shown. The connection is set up.
Forwarding calls on primary line
The call forwarding can only be activated for the primary
line. Which call forwards are possible, how they are configured and activated can be found from Æ page 54.
Call forwarding information
Prerequisite: Your service personnel has activated "Forwarding shown".
If you have activated one of the forwarding types on
your phone for the primary line and a station calls, a
popup window with the following information opens:
• Who is calling
• The forwarding destination.
98
Making calls with multiple lines
Step by Step
During calls
Making and receiving calls on a single line
If you only use one line on your multi-line telephone to
make calls, and you receive calls on the same line, the
phone operates in the same way as a single-line telephone:
• Redial Æ page 50
• Consultation Æ page 51
• Toggle/Connect Æ page 52
• Callback Æ page 60
• Hold Æ page 74
• Call waiting (second call) Æ page 77
• Transferring a call Æ page 80
• Conference Æ page 90
Functions available exclusively for the primary line:
• Call lists Æ page 31
• Voicemail Æ page 30
• Call forwarding Æ page 54
• Do not disturb Æ page 117
Depending on your individual settings, you will
be notified of incoming calls Æ page 115.
Making and receiving calls with multiple
lines
Accepting a waiting call
Depending on the settings for "Rollover", you will
be notified of incoming calls Æ page 115.
Prerequisite: You are conducting a call. At the same
time, a call is incoming on another line.
[ Call on line 1.
T Press the line key for line 2. The call on line 1 is placed
on hold.
99
Making calls with multiple lines
Step by Step
All multi-line users that share the line on which
the call is being held (Æ page 21) can now pick
up the held call. To prevent other users from answering the held call, you must place the call on
"Consultation" hold Æ page 51.
Depending on the setting made by your administrator, you may have to press the trunk key twice
to accept the call on the other line. The first call
is either placed on hold or released depending on
the setting.
[ Conduct call on line 2.
\ End call on line 2.
T Press line key for line 1.
[ Retrieve call on line 1.
Putting a line on hold
On a multi-line telephone you can use the line keys to
place calls on hold.
Prerequisite: You are conducting a call.
R Press the call-line sensor key.
T • The LED line key flashes.
•
•
The LED line displays the hold status on all multi-line
phones to which the line is connected.
On phones connected to the line, a user can press
the relevant line key and accept the held call.
During a consultation call or after accepting a waiting
call the hold function cannot be used.
100
Making calls with multiple lines
Step by Step
Lines with hot or warm line function
Your service personnel can configure a hot or warm line
for the primary and secondary line.
The function is activated when on
• the primary line
you pick up the phone’s handset or press the line or
loudspeaker key
• the secondary line
you press the line key.
A number specified by you is dialed with a hot line immediately and with a warm line after a specific time.
Examples:
• The phone in the lift immediately dials the reception
number.
• The phone at a patient’s bed dials the ward number
e.g. after a minute if no other number is dialed.
Entering a number for the hot and warm line function
Specify which number should be dialed when the hot or
warm line function is activated.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j User passwordEnter and confirm the .
Configuration
Select and confirm the option shown.
Keyset
Select and confirm the option shown.
Lines
Select and confirm the option shown.
Line
Select and confirm the required line in the context
menu.
Hot warm dest
Select and confirm the option shown.
j Enter and confirm the destination.
Save & Exit
Select and confirm the option shown.
101
Making calls with multiple lines
Step by Step
Busy override
A station of a line trunk group is on a call. It’s primary
line is configured as a secondary line on your phone.
This line now has the status "busy." You can join in the
call by pressing the illuminated key of this line (see also
Æ page 21).
Prerequisite: A secondary line is configured on your
multi-line phone and busy override is enabled for you.
The key of secondary line illuminates – it is busy. You
want to join in the call.
R Press the lit key. A conference is established. You are
connected to the parties on the secondary line. The key
continues to illuminates and the conference is shown
on the display.
If there is already a conference on the secondary
line you are connected to this conference. The
conference is shown on the display.
You can now:
• Put the secondary line on hold
• Leave the conference on the secondary line
• Make consultation call
• Accept a second call
• Alternate between a new call party and a conference on the secondary line.
• Include a call party from a consultation or a second
call in the conference.
102
Making calls with multiple lines
Step by Step
Direct station selection keys
Apart from line keys, administrator can also configure
direct station selection (DSS) keys. You can use a DSS
key to call an internal station directly, pick up calls for
this station or forward calls directly to it.
Calling a station directly
You cannot use DSS if the user is on another call (flashing LED).
S
Calling from the idle menu
Press the relevant DSS key.
or
h Press the key shown to open the Overview tab
Æ page 29.
DSS call 1
Select and confirm the DSS line. The key lights up and
a connection is established.
The administrator can configure the DSS key so
that the connection is also established when the
DSS station has activated do-not-disturb or call
forwarding.
Consultation with the DSS station
S
Prerequisite: You are conducting a call and administrator have configured the DSS key for consultation.
Press the relevant DSS key for the consultation. The key
lights up and a connection is established. If the called
party answers, you can toggle, transfer the first call or
initiate a conference.
If administrator have configured transfer instead
of consultation, you can only transfer the current
call to the DSS station.
103
Making calls with multiple lines
Step by Step
Call pickup
You can pick up calls for another DSS station. If a call is
waiting on their line, the LED flashes.
Indirect pickup
Prerequisite: The auto-answer function must be deactivated Æ page 84.
T Press the DSS key. The call is routed to your primary line
and rings.
^ or n or o Lift the handset or press the speakerphone mode or
headset key. You are connected with the other party.
Rejecting a call
Prerequisite: administrator must activate the reject option for DSS keys and auto-answer must be deactivated
Æ page 84.
T Press the DSS key. The call is routed to your primary line
and rings.
Reject
Select and confirm the option shown in the pop-up
menu.
The caller hears a busy signal.
Direct pickup
Prerequisite: The auto-answer function must be activated Æ page 84.
T Press the DSS key. The call is routed to your primary line
and you are immediately connected with the other party via speakerphone.
Deflecting a call to a DSS station
Prerequisite: The Deflect function must be enabled for
DSS keys (see Æ page 71).
If you receive a call on one of your lines, you can immediately deflect it to the DSS station.
T Your phone rings and a line key flashes.
S Press the relevant DSS key. The call is deflected to the
DSS station. If the DSS station does not answer, you
can pick up the call by pressing the DSS key.
104
Making calls with multiple lines
Step by Step
LED display on DSS keys
DSS Key
Explanation
S
Off: The line is in idle mode.
T
Flashes: You can accept a call for the DSS
station via the key. The call is routed to
your primary line when the call is accepted.
R
Illuminates: The line is busy. Provided
that second call is activated you can still
reach the DSS station via the key. It can
accept your call as a second call.
105
Making calls with multiple lines
Making calls in an executive-secretary team
An executive-secretary team is configured by the relevant service personnel and may include up to four executive and up to two secretary telephones.
Sample scenarios
This example assumes that two executive and two secretary phones are
configured. Calls for the executives are forwarded immediately to the respective secretary phone. A secretary then connects the call with or without consultation to the responsible executive using the direct station selection key.
Secretary 1
Secretary 2
Line
Line
Executive 1
Executive 1
Executive 2
Executive 2
Secretary 2
Secretary 1
Call waiting
Call waiting
Shift
Shift
Executive 1
Executive 2
Line
Line
Secretary 1
Secretary 2
Secretary 2
Secretary 1
Shift
Shift
Prerequisites:
The following call forwards are configured (Æ page 54 ):
• For All calls from Executive 1 to Secretary 1
• For All calls from Executive 2 to Secretary 2
• Forward on Busy and forward on No reply from Secretary 1
to Secretary 2
• Forward on Busy and forward on No reply from Secretary 2
to Secretary 1
"Allow call waiting" should be activated on the secretaries’ phones
(Æ page 79). This function can optionally be activated and deactivated using a key if a key has been configured for it.
Line and direct station selection keys have been configured by service personnel and "Transfer on hangup" and server features have been activated.
106
Making calls with multiple lines
Step by Step
Accepting a call
Incoming calls for the executives should be forwarded
immediately to the assigned secretary and answered
there. The line overview (Æ page 110) shows whether
the executive has activated call forwarding.
Accepting calls at the secretary phone
An incoming call for "Executive 1" rings at the assigned
"Secretary 1".
The line key of the "Secretary 1" phone flashes.
The "Secretary 1" direct station selection key on
the "Executive 1" phone also flashes.
T Press the line key to answer the call. The station answers. The line key flashes rapidly.
The "Secretary 1" direct station selection key on
the "Executive 1" phone illuminates.
Early call pickup by Executive 1
An incoming call for "Executive 1" rings on "Secretary 1".
The "Secretary 1" direct station selection key on the
"Executive 1" phone flashes. The "Secretary 1" has not
yet answered the call. Before the call is forwarded to
"Secretary 2", "Executive 1" picks up the call early.
T Press the "Secretary 1" direct station selection key on
the "Executive 1" key to answer the call.
If for example a call for "Secretary 2" on
"Executive 2" is not answered, "Secretary 1" or
"Executive 1" can pick up the call early
107
Making calls with multiple lines
Step by Step
Forward to Secretary 2
An incoming call for "Executive 1" rings at the assigned
"Secretary 1". The call is not answered. After a specified
period the call is forwarded to "Secretary 2". The line key
of the "Secretary 2" flashes and it rings.
T Press the line key on the "Secretary 2" phone to answer
the call. The station answers. The "Secretary 2" direct
station selection key on the "Executive 1" phone illuminates.
If "Secretary 1" is busy, the call is forwarded immediately to "Secretary 2" if:
• a consultation call is being made or
• "Allow call waiting" is deactivated.
Second call
If "Secretary 1" receives a second call, this can be accepted, ignored, forwarded or rejected. Detailed information on this can be found from Æ page 77.
If the second call is ignored, it is forwarded to
"Secretary 2" after a certain period of time.
If the second call was answered, it can be forwarded using consultation or the direct station selection keys.
Connecting a call
If e. g. the "Secretary 1" answered a call, it can forward
the call using the direct station selection keys to the following telephones:
• Executive 1
• Executive 2
• Secretary 2.
The following examples show connections to
"Executive 1".
108
Making calls with multiple lines
Step by Step
Connecting with consultation
S Press the DSS "Executive 1" key. "Executive 1" answers.
Announce the call.
\ or n or o Press the hang-up, loudspeaker or headset key.
You can also select "Complete Xfer" from the context ment.
Connecting without consultation
S Press the DSS "Executive 1" key. "Executive 1" does not
answer.
Complete transfer
Select and confirm the option shown in the pop-up
menu.
\ or n or o Press the hang-up, loudspeaker or headset key. The
"Executive 1" phone rings.
If "Executive 1" does not answer the call, after a specified time the number is redialed ( see also Æ page 80).
The "Executive 1" direct station selection key on
the "Secretary 1" phone illuminates.
Consultation without connecting
S Press the DSS "Executive 1" key. "Executive 1" answers.
Transferring is not wanted. The "Secretary 1" takes the
call back
Disconnect & return
Select and confirm the option shown in the pop-up
menu. The "Secretary 1" is reconnected with the caller.
Toggle, disconnect or conference
During a consultation call "Secretary 1" can toggle between "Executive 1" and the caller, can initiate a conference or disconnect one of the two call parties. More on
this subject can be found on pages Æ page 52 and
Æ page 90.
109
Making calls with multiple lines
Step by Step
DSS keys can be used
These keys are configured in such a way that every
phone can be reached by every phone in the group. The
DSS keys are also used for consultation calls.
S Press a team member’s DSS key. The relevant phone
rings and the party answers.
Using line overview
To view the status of the lines, change from the "My
phone" tab to the "Overview" tab on the phone screen
with the h key.
Overview
Line g
DSS:Executive 2
Line
Bohr, Niels
Executive 1
Line busy
Executive 2
DSS:Secretary 2 0123456
Secretary 2
DSS:Executive 1Line forwarded
Shift
Further information on the line status can be found on
Æ page 29.
The "executive-secretary" team can be expanded with
line keys by the service personnel. These lines keys
however have no influence on the behavior of the "executive-secretary" configuration.
110
Making calls with multiple lines
Step by Step
Settings for multi-line phones (keyset)
The details for each keyset line contain supplementary
information for the user. The following uneditable fields
are displayed:
• Address
– Displays the phone number for the line
• Ring on/off
– Shows whether the ringer is activated for this line
• Selection sequence
Displays the priority of each line seizure when the handset is lifted or the loudspeaker key for this line is
pressed
Displaying the line in the "Overview" tab
Specify here if the selected line should be displayed in
the "Overview" tab.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Keyset
Select and confirm the option shown.
Lines
Select and confirm the option shown.
Line 1
Select and confirm the required line (for example, line 1).
Allow in overview
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Select and confirm the option shown.
111
Making calls with multiple lines
Step by Step
Setting the time for a delayed ringer
Specify the length of time before a held call should be
signaled on a line.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Keyset
Select and confirm the option shown.
Lines
Select and confirm the option shown.
Line 1
Select and confirm the required line (for example, line
1).
Ring delay
Select and confirm the option shown.
j Enter and confirm a delay value.
Save & Exit
Select and confirm the option shown.
You can activate and deactivate the set delay time for all
line keys using a function key Æ page 68.
112
Making calls with multiple lines
Step by Step
Configuring the "Overview" tab display
Specify here the sequence in which the individual lines
in the "Overview" tab should appear on the display.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Keyset
Select and confirm the option shown.
Overview
Select and confirm the option shown.
All lines that are displayed in the overview are listed.
Line 1
Select and confirm the required line (for example, line 1).
Select one of the following options from the context
menu to move an individual line:
• Move up
• Move down
• Move to top
• Move to bottom
or
Use FPK order
Select and confirm the option shown to arrange the
lines in the same sequence as the line keys
or
Add all lines
Select and confirm the option shown to display all line
keys in the overview.
The setting made for "Allow in overview"
(Æ page 111) is disregarded here.
Save & Exit
Select and confirm the option shown.
113
Making calls with multiple lines
Step by Step
Line preview
Activating via the line keys
Prerequisite: You are already on a call on one line and a
further call rings on the secondary line. Service personnel have activated line preview.
T Press the flashing trunk key. A popup window opens
and you receive information about the caller.
T Press the flashing line key to answer the second call.
If service personnel have deactivated the line
preview, a call is answered immediately on a second line when the line key is pressed, without
showing caller information.
Activating via preview key
Prerequisite: You have programmed a sensor key with
the "Preview"Æ page 64 . Your service personnel have
activated the preview function.
Preview for a call:
You are already conducting a call on one line. A further
call rings on a secondary line.
S
Press the "Preview" sensor key. A popup window
opens and you receive information about the caller.
R Press the "Preview" sensor key again to hide the pre-
view or wait until the popup closes itself after a specified period of time.
Permanent preview
S Press the "Preview" key in idle mode. This way the preview for all lines with "preview mode" remains active until you press the "Preview" sensor key again.
114
Making calls with multiple lines
Step by Step
Rollover for a line
T
Your administrator can determine how rollover calls are
to be signaled.
Only the relevant line key blinks.
or
Z T You hear a special advisory tone via the currently acor
tive microphone and the corresponding line key blinks.
Z T The ringer melody set sounds briefly (approx.
3 seconds) via the loudspeaker and the corresponding
line key blinks.
Z T You hear a short notification tone
The ringer melody is not played in speakerphone
mode.
Z T k The telephone rings using the configured call signal, the
corresponding line key blinks, and a pop-up menu containing the available information is displayed.
115
Privacy/security
Step by Step
Privacy/security
Deactivating the ringer
You can deactivate your ring tone if you do not want to
be disturbed by your phone ringing.
) Hold down the key shown.
The "Ringer off" icon appears in the status bar on the
idle display Æ page 25.
) Hold down the key once again to reactivate the ringer.
The icon disappears.
You can also switch the function on and off using the option in the idle menu.
Ringer off?
Select and confirm the option shown.
or
Deactivating the ring tone via sensor key
Prerequisite: The "Ringer off" sensor key must be
configuredÆ page 64.
S
Press the "Ringer off" sensor key.
S An incoming call is signaled by a single ring tone burst.
R Press the lit sensor key once more to deactivate the
"Ringer off" function.
116
Privacy/security
Step by Step
Do not disturb
If "Do not disturb" is activated, your telephone will not
ring. The caller hears the busy signal.
On multi-line telephones (Æ page 12) you can
only activate the "Do not disturb" function for
your primary line.
Prerequisite: A programmable key is assigned the
function "Do Not Disturb" (seeÆ page 64). "Do not disturb" must be activated (Æ page 118).
Enabling "Do not disturb" via a key
S Press the "Do not disturb" programmable key.
T The programmable key blinks to signal incoming calls.
The caller hears the busy signal. Calls for pickup groups
are however connected.
R Press the lit programmable key once more to deactivate
the "Do not disturb" function.
You can also use the programmable key to activate the "Do not disturb" function during a call or
deactivate it when an incoming call is being signaled.
or
Enabling "Do not disturb" via the idle menu
Do not disturb on
Select and confirm the option shown in the idle menu.
The "Do not disturb" icon appears in the header.
or
Do not disturb off
Select and confirm the option shown in the idle menu.
The "Do not disturb" icon is deleted.
117
Privacy/security
Step by Step
Allowing "Do not disturb"
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Incoming calls
Select and confirm the option shown.
Handling
Select and confirm the option shown.
Allow DND
Select and confirm the option shown.
Yes
Select and confirm the option shown.
Save & Exit
Select and confirm the option shown.
118
Privacy/security
Step by Step
Security
User password
Your User password protects your individual configurations, including your language settings. You can also use
the User password to lock your telephone Æ page 121.
The preset password "000000" corresponds to a
blank password. In other words, the phone cannot be locked and the user menu is not password protected (see also Æ page 120).
z You can also change the user password via the Web interface Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Change and confirm User password.
Security
Select and confirm the option shown.
User password
Select and confirm the option shown.
j Specify a new password (at least six characters, text entry, see Æ page 24) and confirm your entry.
Confirm password
Select and confirm the option shown.
j Enter the password again and confirm.
Save & Exit
Select and confirm the option shown.
119
Privacy/security
Step by Step
Deactivating the user password
You can deactivate the phone’s password prompt if a
password has already been configured.
Deactivating the password prompt does not apply to the web-interface Æ page 162, OpenStage
Manager or CTI applications that use a password
prompt. The password "000000" must be entered here.
If you deactivate the user password, you are not
able to lock the phone Æ page 121 and the user
menu is not password-protected.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Change and confirm User password.
Security
Select and confirm the option shown.
User password
Select and confirm the option shown.
if nec. h Press the key to delete the existing password.
j Enter six zeros ("000000“) to deactivate the password
(for text input, see Æ page 24) and confirm.
Confirm password
Select and confirm the option shown.
j Enter six zeros ("000000") once again and confirm.
Save & Exit
120
Select and confirm the option shown.
Privacy/security
Step by Step
Locking the phone
You can lock your phone to protect it against unauthorized access. In this way, no one can make calls or
change your user settings unless they know your user
password.
Predefined numbers from the dial plan can still be dialed
when the phone is locked. For more information, contact your administrator.
If an emergency number is entered by administrator,
"Emergency call" appears on the display when you use
the line on a locked phone.
You can only lock the phone if you set a user
password (Æ page 119). The password for this
should not match the default "000000".
Activating the phone lock
( Hold down the key shown until "Phone lock: Confirm
locking the phone" appears.
Confirm lock
Confirm the option shown. The phone is locked.
or
N Press the key shown.
User
Select and confirm the option shown.
j Enter and confirm the User password.
Security
Select and confirm the option shown.
Phone lock
Select and confirm the option shown.
Yes
Select and confirm the option shown.
Save & Exit
Select and confirm the option shown. The phone is
locked.
121
Privacy/security
Step by Step
Unlocking the phone
Unlock phone
Confirm the option shown.
j Enter and confirm the User password. The phone is unlocked if the password is correct.
Emergency numbers and predefined numbers
from the dial plan can be dialed from a locked
phone.
If the telephone is locked repdial keys cannot be
used. This also applies when emergency numbers or predefined numbers from the dial plan
are stored on them.
122
Mobility
Step by Step
Mobility
Prerequisite: Your phone is configured to support mobility by administrator. A DLS server is available in the
LAN and its address is entered in the phone.
Mobility scenarios
When you log on to your phone, or any other mobilityenabled phone, the following scenarios are possible:
Logging on and off at the same phone
•
•
Log on as a mobility user Æ page 124.
Log off as a mobility user Æ page 125.
Logging on and off at different phones
In these cases, administrator may have made the following settings:
• Log on at a remote phone with forced logon, when
the user is still logged on at that phone Æ page 126.
• Delayed logon at a remote phone with forced logon,
when the user is still logged on at that phone and
the phone is busy Æ page 127.
123
Mobility
Step by Step
Logging on and off at the same phone
Logging on to the phone
No other mobility user is logged on.
Logon via a key
If one of the program keys is configured for the mobility
function.
S Press the "Mobility" program key.
or Logon via a menu
Mobile logon
Select and confirm the option shown in the telephony
interface context menu (Æ page 28).
The Mobility logon dialog appears.
Mobility ID
Select and confirm the option shown.
j Enter and confirm the mobility code (generally your official phone number).
User password
Select and confirm the option shown.
j Enter the user password and confirm with OK (select
the input mode if necessary).
Logon
Select and confirm the option shown in the context
menu.
The following messages appear on the display:
• Logging on mobile user
• Validating
• Registering
• Downloading user data
Once logon is complete, the "Mobility" program key
LED lights up and the mobility icon
appears in the
graphic display next to the mobile phone number.
124
Mobility
Step by Step
Logging off from the phone
Prerequisite: You are logged on as a mobility user.
R Press the "Mobility" program key.
or Log on via the telephony interface context menu
Æ page 28.
Mobile logoff
Select and confirm the option shown. The logoff procedure starts immediately.
or If you need to enter a password, the following message
appears:
"Mobility logoff User password required"
Please Enter Password
Select and confirm the option shown. You will see the
prompt, "Please enter mobility password"
j Enter user password.
Please Enter Password
Select and confirm the option shown.
If you enter the password incorrectly, the following message appears: "User password invalid" .
You can cancel the function or retry the user
password.
The logoff procedure begins. In the graphic display, the
following messages appear:
• Logging off mobile user
• Uploading user profile
• Registering
• Downloading user data
After you have logged off, the mobility icon
den.
is hid-
125
Mobility
Step by Step
Logging on at different telephones
An attempted login is rejected if the user is already
logged on to another phone and "Logon with forced
logoff" is disabled for the mobility user.
Logging on with forced logoff at a remote
phone
If the user is already logged on at another phone and
the remote phone is busy, the logon is rejected.
If, however, your administrator enabled "Forced logoff
during call" without setting a time, the system does not
consider whether or not the remote phone is busy.
Logon via a key
If one of the program keys is configured for the mobility
function.
S Press the "Mobility" program key.
or Logon via a menu
Mobile logon
Select and confirm the option shown in the telephony
interface context menu Æ page 28.
The Mobility logon dialog appears.
Mobility ID
Select and confirm the option shown.
j Enter and confirm the mobility code (generally your official phone number).
User password
Select and confirm the option shown.
j Enter and confirm the user password.
Logon
Select and confirm the option shown.
The following mobility messages appear in the display:
• Validating
• Logging off elsewhere
• Registering
• Downloading user data
The logoff is simultaneously displayed on the remote
phone. Once logon is complete, the "Mobility" program
key LED lights up and the mobility icon appears in the
graphic display
.
126
Mobility
Step by Step
Logging on with forced, delayed logoff at
a remote phone
If the remote phone is busy and your administrator enabled "Forced logoff during call" with a set timeout,
forced logoff does not occur until this timeout expires.
Logon via a key
S Press the "Mobility" program key. You are prompted to
enter your mobility password.
or Logon via a menu
Mobile logon
Select and confirm the option shown in the telephony
interface context menu Æ page 28.
The Mobility logon dialog appears.
Mobility ID
Select and confirm the option shown.
j Enter and confirm the mobility code (generally your official phone number).
User password
Select and confirm the option shown.
j Enter and confirm the user password.
Logon
Select and confirm the option shown.
The following mobility messages appear in the display:
• Validating
• Logging off elsewhere
At the same time, the graphic display on the
busy remote phone shows "Forced logoff pending". After the timeout set by your administrator,
the active call is ended and remote logoff is performed.
•
•
Registering
Downloading user data
Once logon is complete, the "Mobility" program key
LED lights up and the mobility icon appears in the
graphic display
.
127
OpenScape Voice functions
Step by Step
OpenScape Voice functions
The OpenScape Voice supports a number of functions
that you can activate and deactivate from your phone.
On multi-line telephones, the full scope of OpenScape Voice functions is only available for the primary line.
Feature toggle key
You can pick a programmable sensor key and program it
as a feature toggle key for activating the "make line
busy" and "stop hunt" functions.
You can then use the programmable sensor key to activate or deactivate the relevant OpenScape Voice function on the server for this phone.
You can only program first-level programmable sensor
keys because those linked to LEDs are used to display
function status as either on (LED on) or off (LED off).
The LED indicates the status of the function on the
server and can therefore change without any of the programmable sensor keys being pressed.
Example:
Switching between "Line busy" and "Line free" (see also
Æ page 135).
S
Prerequisite: Your administrator configured a programmable sensor key with the function "Busy" ("make line
busy" for the hunt group) Æ page 67.
Press the programmable sensor key – the key lights up.
R Press the illuminated programmable sensor key once
again to release the line - the keys stops illuminating.
128
OpenScape Voice functions
Step by Step
Making anonymous calls
Your administrator decides whether or not your caller ID
(name and phone number) is displayed on a called party’s station. Anonymous calling is when your data is
not transmitted. The settings configured can be deactivated, however, for specific calls.
•
•
If your caller ID is transmitted: your caller ID is
displayed.
If your caller ID is suppressed: "unknown" is
displayed.
Deactivating
If your administrator permanently activated anonymous calling for your phone, you can deactivate this
setting as follows:
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143) to
transmit the caller information.
Z You hear a confirmation tone.
Activating
If your administrator activated caller ID transmission for
your phone, you can deactivate this setting as follows:
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143) to
suppress the caller ID.
Z Wait until you hear the confirmation tone.
Caller ID transfer is suppressed. "Private/Anonymous"
appears on the called party’s display instead of the caller ID.
129
OpenScape Voice functions
Step by Step
Temporarily activating anonymous calling for
the next call
If your administrator activated caller ID transmission for
your phone, you can deactivate this setting for the next
call as follows:
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143).
Z Wait until you hear the confirmation tone.
j Dial the phone number of the party you want to contact.
Caller ID transmission is reactivated after this call.
Temporarily deactivating anonymous calling
for the next call
If your administrator suppressed caller ID transmission
for your phone, you can enable this setting for the next
call as follows:
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143).
Z Wait until you hear the confirmation tone.
j Dial the phone number of the party you want to contact.
When you end this call, caller ID transmission is suppressed once again for the next call.
130
OpenScape Voice functions
Step by Step
Creating a list for selective calls
For call acceptance
You can create a list of the phone numbers from which
you are willing to accept calls (also known as a selection
list). Your administrator know how long this list may be
in the OpenScape Voice used on site in your facility.
A connection is set up if a caller’s phone number matches a number in the selection list. If the caller’s number
does not appear in the list:
• the caller receives a message that the party refuses
to accept any calls from this number,
or •
the call is forwarded to an external phone number.
Contact your administrator for information on how your
OpenScape Voice is configured on site.
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143).
Various announcements deliver the following information:
• the name of the feature (selective call acceptance)
• the current status (active or inactive)
• the current scope of the selection list.
These announcements are followed by verbal user
prompts that let you:
• add entries to the selection list
• delete entries in the selection list
• check the selection list
• activate or deactivate the function.
131
OpenScape Voice functions
Step by Step
For call rejection
As for selective call acceptance, you can create a selection list with the phone numbers of parties from whom
you are not willing to accept calls. Your administrator
know how long this list may be in the OpenScape Voice
used on site in your facility.
A call is not connected if the caller’s phone number
matches a number in the selection list; the caller is notified that the called party rejects calls from this number. If the caller’s number is not in the selection list, the
call is to you as usual.
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143).
Various announcements deliver the following information:
• the name of the feature (selective call rejection)
• the current status (active or inactive)
• the current scope of the selection list.
These announcements are followed by verbal user
prompts that let you:
• add entries to the selection list
• delete entries in the selection list
• check the selection list
• activate or deactivate the function.
132
OpenScape Voice functions
Step by Step
Anonymous calls
Rejecting
You can reject all calls from parties that activated a data
protection feature (for example, caller ID suppression)
to prevent their phone number from being transmitted.
In this case, you are not informed that a call was rejected.
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143).
Accepting
You can also accept calls from parties that activated a
data protection feature (for example, caller ID suppression) to prevent their phone number from being transmitted.
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143).
133
OpenScape Voice functions
Step by Step
Using abbreviated dialing
Abbreviated dialing gives you access to a central list of
frequently dialed phone numbers.
You can dial a specific phone number by simply entering
a digit string. As these are three-digit numbers, you can
store up to 1000 phone numbers. This list is stored centrally and managed by your administrator.
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143) followed by a number between 0 and 999 for the phone
number you want to dial.
The number is automatically dialed.
Call tracing
You can request the automatic tracing of the last received internal call. This is particularly suitable for identifying malicious, irritating or troublesome calls.
n Lift the handset.
o Enter the code (see the code table Æ page 143). The
phone number is determined. Ask your service personnel for the result.
134
OpenScape Voice functions
Step by Step
Hunt group functions
To ensure optimum handling of specific calls, your telephone can be assigned to a pickup group Æ page 44
and/or a hunt group.
Your administrator can incorporate multiple telephones
in a hunt group. If your telephone is assigned to a hunt
group, OpenScape Voice forwards calls for the members of your group in accordance with specific rules defined by your administrator. Hunt groups are a simple
solution for distributing calls to a group of telephones.
If you want another member of the group to pick up an
incoming call, you can set your telephone to signal the
busy status for your line to the other members of the
hunt group. Hunt group calls will then no longer be forwarded to your telephone.
This feature can also be configured using the programmable feature toggle key Æ page 128.
Making a line busy
This prevents this line being used for calls in a hunt
group.
Activating
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143).
Z Wait until you hear the confirmation tone.
Deactivating
Make the line free once more for the hunt group.
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143).
Z Wait until you hear the confirmation tone.
135
OpenScape Voice functions
Step by Step
Marking the last line in the hunt group chain
Sets the "stop hunt" line in the hunt group chain. The
system will stop looking for a free line in the hunt group
chain after it reaches this line.
Activating
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143).
Z Wait until you hear the confirmation tone.
Deactivating
Unmark the line as the end of the hunt group chain.
^ Lift the handset.
j Enter the code (see the table of codes Æ page 143).
Z Wait until you hear the confirmation tone.
136
OpenScape Voice functions
Step by Step
Reachability
You can make either serial calls or simultaneous calls on
several sites. The features for this are
• Serial call
• Parallel call
Prerequisite: The service personnel has configured the
respective feature for your main number in OpenScape
Voice.
Serial call
Managing number lists/activating serial call
Before the serial call number can be activated, a serial
call list much be created. This can be prepared either by
service personnel or you can create it yourself later. Up
to six numbers can be entered in the list for sites on
which incoming calls including your main number
should be signaled sequentially. Each number can consist of up to 30 digits.
^ Lift the handset.
j Enter the code for the edit mode (see code table
Æ page 143).
The edit mode opens and you hear an announcement
with the following information:
• Feature name
• Current status (active/inactive)
• Number of numbers currently on the serial call list
You are prompted to do one of the following:
• Activate/deactivate the feature (only if numbers are
already entered in the list)
• Call up the numbers currently entered in the list.
• Add or delete numbers
• Repeat the options in edit mode
If the serial call list is still empty, you are prompted to
enter numbers in the list. As soon as you have entered
a valid number, the serial call can be activated.
If the serial call is activated, incoming calls are first routed to your phone. If you do not answer within the timeframe defined by the service personnel, the next destination phone rings for the configured period of time.
137
OpenScape Voice functions
Step by Step
The caller is informed that the call is being routed to
another station. The connection is established with the
first phone that accepts the call.
If the call is not answered by any phone, it is forwarded
to the configured forwarding destination (on no reply) or
to a "rejection announcement".
Parallel call
Managing number lists/activating parallel call
Before the parallel call feature can be activated, a parallel call list must be created. This can be prepared either
by service personnel or you can create it yourself later.
Up to six numbers can be entered in the list for sites on
which incoming calls including your main number
should be signaled sequentially. Each number can consist of up to 30 digits.
^ Lift the handset.
j Enter the code for the edit mode (see code table
Æ page 143).
The edit mode opens and you hear an announcement
with the following information:
• Feature name
• Current status (active/inactive)
• Number of numbers currently on the parallel call list
You are prompted to do one of the following:
• Activate/deactivate the feature (only if numbers are
already entered in the list)
• Call up the numbers currently entered in the list.
• Add or delete numbers
• Repeat the options in edit mode
If the parallel call list is still empty, you are prompted to
enter numbers in the list. As soon as you have entered
a valid number, the parallel call can be activated.
If the parallel call is activated, incoming calls are routed
to your phone and all other destination phones in the parallel call list. The connection is established with the
first phone that accepts the call.
If the call is not answered by any phone, it is forwarded
to the configured forwarding destination (on no reply) or
to a "rejection announcement".
138
OpenScape Voice functions
Step by Step
Activating/deactivating parallel call via code
You can activate/deactivate the parallel call without having to change to edit mode.
Prerequisite: You have already entered numbers in the
parallel call list.
^ Lift the handset.
j Enter the code to activate or deactivate the parallel call
(see code table Æ page 143).
139
OpenScape Voice functions
Step by Step
Parking a call
If you have answered a call for a colleague and cannot
forward it to him, you can park the call.
Park a call
[ You are conducting the call. Let the other party know,
e.g. that you hare trying to connect him.
j Enter the code for parking followed by a line number
(see code table Æ page 143).
You receive a confirmation tone. The caller hears a waiting melody.
] Replace the handset
Tell your colleague that a call for him is parked and give
him the line number.
Unparking
To unpark the call, your colleague must proceed as follows:
^ Lift the handset.
j Enter the unparking code (see code table Æ page 143).
He is prompted to enter a line number.
j Enter the specified line number.
[ Your colleague is now connected with the waiting caller.
140
OpenScape Voice functions
Step by Step
Silent Monitoring
If this function has been configured by service personnel and enabled for the destination phone, you can join
an active call of an internal station and listen in unnoticed (muted) or with the knowledge of the target
station (active).
Active silent monitoring
Station A and B are on a call. You want to listen to the
call but so that Station B does not notice but so that you
can still talk to Station A.
Your phone
internal station A
internal or external station B
•
•
•
You can hear and talk to station A.
You can hear station B but cannot talk to him because he cannot hear you.
Station A and B can hear and speak to each other.
^ Lift the handset.
j Enter the code for active silent monitoring and the destination number (see code table Æ page 143). You are
connected to the call and can listen. If necessary notify
station A.
] End the silent monitoring unnoticed by replacing the
handset.
141
OpenScape Voice functions
Step by Step
Muted silent monitoring
Station A and B are on a call. You want to monitor a call
but so that neither station notices.
Your phone
internal station A
internal or external station B
•
•
•
You can hear station A but cannot talk to him because he cannot hear you
You can hear station B but cannot talk to him because he cannot hear you.
Station A and B can hear and speak to each other
^ Lift the handset.
j Enter the code for active silent monitoring and the destination number (see code table Æ page 143). You are
connected to the call and can listen.
] End the silent monitoring unnoticed by replacing the
handset.
142
OpenScape Voice functions
Table of codes for OpenScape Voice functions
Ask your administrator to enter the latest codes in the following table. Print
this page as an overview.
Function
143
Code
Description
Making anonymous calls off
Æ page 129
Making anonymous calls on
Æ page 129
Making anonymous calls temporarily on
Æ page 130
Making anonymous calls temporarily off
Æ page 130
List for selective call acceptance
Æ page 131
List for selective call rejection
Æ page 132
Rejecting anonymous calls
Æ page 133
Accepting anonymous calls
Æ page 133
Using abbreviated dialing
Æ page 134
Call tracing
Æ page 134
Making a line busy on
Æ page 135
Making a line busy off
Æ page 135
End of hunt group chain on
Æ page 136
End of hunt group chain off
Æ page 136
Edit mode for serial call
Æ page 137
Edit mode for parallel call
Æ page 138
Activating a parallel call
Æ page 139
Deactivating a parallel call
Æ page 139
Parking a call
Æ page 140
Unparking a call
Æ page 140
Active silent monitoring
Æ page 141
Muted silent monitoring
Æ page 142
Individual phone configuration
Step by Step
Individual phone configuration
Display
Adjusting the display to a comfortable reading angle
You can swivel the display unit. Adjust the display unit
so that you can clearly read the screen.
Setting contrast
The display has six contrast levels that you can set according to your light conditions.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Phone
Select and confirm the option shown.
Display
Select and confirm the option shown.
Contrast
Select and confirm the option shown.
gh Set and confirm the contrast.
Save & Exit
Confirm the option shown.
Background lighting
Your service personnel can set a time of between two
and eight hours defining how long the phone should be
idle before display backlighting deactivates completely.
144
Individual phone configuration
Step by Step
Contrast for the OpenStage Key Module
If an OpenStage Key Module is connected to your
OpenStage 40, you can set contrast for it.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Phone
Select and confirm the option shown.
Display
Select and confirm the option shown.
Key mod. contrast
Select and confirm the option shown.
gh Set and confirm the contrast.
Save & Exit
Confirm the option shown.
145
Individual phone configuration
Step by Step
Date and time
You can set the date and time display here if necessary.
z You can also configure this setting via the Web interface
Æ page 162.
You must set the date and time manually if your
phone is not connected to an (S)NTP server.
Setting the time
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Date and time
Select and confirm the option shown.
Time
Select and confirm the option shown.
j Enter and confirm the time.
Save & Exit
Confirm the option shown.
Setting the date
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Date and time
Select and confirm the option shown.
Date
Select and confirm the option shown.
j Enter and confirm the date.
Save & Exit
146
Confirm the option shown.
Individual phone configuration
Step by Step
Setting daylight saving time
Prerequisite: Auto DST is deactivated Æ page 148.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Date and time
Select and confirm the option shown.
Daylight saving
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Confirm the option shown.
Setting the difference between daylight saving and
standard time
Prerequisite: Auto DST is deactivated Æ page 148.
Enter the difference to be used for daylight saving time.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Date and time
Select and confirm the option shown.
Difference (mins)
Select and confirm the option shown.
j Enter and confirm the difference between daylight and
standard time in minutes.
Save & Exit
Confirm the option shown.
147
Individual phone configuration
Step by Step
Automatic daylight saving time
The Auto DST setting is provided for information purposes and can only be changed by your administrator.
z You can also access this information via the Web interface Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the user password.
Date and time?
Select and confirm the option shown.
Daylight saving time must be manually set if a No is entered for Auto DST Æ page 147.
Time display format
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Locality
Select and confirm the option shown.
Time format
Select and confirm the option shown.
24 hour
Select and confirm the time format (12- or 24-hour display) in the context menu.
Save & Exit
Confirm the option shown.
148
Individual phone configuration
Step by Step
Date display format
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Locality
Select and confirm the option shown.
Date format
Select and confirm the option shown.
dd/mm/yyy
Select and confirm the format you want.
Save & Exit
Confirm the option shown.
149
Individual phone configuration
Step by Step
Audio
Volumes
Use this selection to set the following volumes:
• Loudspeaker
• Ringer
• Handset
• Headset
• Handsfree
• Rollover
Example: Handset
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Audio
Select and confirm the option shown.
Volumes
Select and confirm the option shown.
Handset
Select and confirm the volume you want to adjust (for
example, "Handset").
gh Set and confirm the volume.
An acoustic sample of the current volume is output via
audio feedback when you adjust the volume.
Save & Exit
150
Confirm the option shown.
Individual phone configuration
Step by Step
Settings
Room character
To ensure that the other party can hear you properly in
speakerphone mode, you can adjust the phone to the
room acoustics by choosing one of the following room
character conditions: "Normal", "Echoing", "Muffled" .
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Audio
Select and confirm the option shown.
Settings
Select and confirm the option shown.
Room character
Select and confirm the option shown.
Normal
Select and confirm the room character in the context
menu (for example, "Normal") (z Æ page 164).
Save & Exit
Confirm the option shown.
Ringtone
If your service personnel has loaded suitable files to the
phone, you can select a realtone file in *.mp3 or *.wav
format for the ringer tone. If no individual audio files are
available the "pattern" ringtone is preset.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Audio
Select and confirm the option shown.
151
Individual phone configuration
Step by Step
Settings
Select and confirm the option shown.
Ringer melody
Select and confirm the option shown.
ABC.wav
Select and confirm the required ringer file[1] or "pattern."
You will immediately hear the associated ringer melody.
Confirm current ringtone file.
Save & Exit
Confirm the selected ringtone to use it or try a different
ringtone.
Pattern melody
z You can also configure this setting via the Web interface
Æ page 162.
Prerequisite: You have chosen the "pattern" ringtone,
see Æ page 151.
N Press the key shown.
User
Select and confirm the option shown.
evtl. j Enter and confirm the User password.
Audio
Select and confirm the option shown.
Settings
Select and confirm the option shown.
Ringer tone sequence
Select and confirm the option shown.
4
Select the required pattern melody[1] between 1 and 8
(e. g. 4). You will immediately hear the corresponding
Ringer melody. Confirm the selected Ringer melody.
Save & Exit
Select and confirm the option shown.
1. The phone displays the current setting.
152
Individual phone configuration
Step by Step
Pattern sequence
z You can also configure this setting via the Web interface
Æ page 162.
Prerequisite: You have chosen the "pattern" ringtone,
see Æ page 151.
N Press the key shown.
User
Select and confirm the option shown.
Audio
Select and confirm the option shown.
Settings?
Select and confirm the option shown.
Ringer tone sequence
Select and confirm the option shown.
2
Select your desired Ringer tone sequence between 1
and 3 (e. g. 2) You immediately hear the set Ringer melody with the chosen Ringer tone sequence. Confirm
the selected setting.
Save & Exit
Select the option shown and confirm twice.
153
Individual phone configuration
Step by Step
Country setting for speakerphone mode
Enter the country setting you prefer for speakerphone
mode here (see Æ page 40).
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Audio
Select and confirm the option shown.
Settings
Select and confirm the option shown.
Open listening
Select and confirm the option shown.
Standard mode
Select and confirm the setting you want in the context
menu ("Standard mode" or "US mode").
Save & Exit
Confirm the option shown.
154
Individual phone configuration
Step by Step
Setting headset port use
Here you set whether you are using a wired or cordless
DECT headset.
z You can also configure this setting via the Web interface
Æ page 162.
v Press the key shown until the "Menu" tab is active.
User
Confirm the option shown.
if nec. j Enter and confirm the user password.
Audio
Select and confirm the option shown.
Settings
Select and confirm the option shown.
Headset port
Select the option shown.
Wired headset
From the following setting1 select and confirm the option shown in the context menu.
• Wired headset
• Wireless headset
• Conference phone
Save & Exit
Select and confirm the option shown.
1. The phone displays the current setting.
155
Individual phone configuration
Step by Step
Nonsecure voice communication tone and
message
Use this option to activate an alerting tone that you hear
when a secure voice connection with the party you are
currently talking to ceases to be secure. The message
"Nonsecure connection" also appears.
Prerequisite: Secure connection setup is the preference set by your administrator.
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Configuration
Select and confirm the option shown.
Connected calls
Select and confirm the option shown.
Secure call alert
Select and confirm the option shown.
Yes
Select and confirm the option shown in the context
menu.
Save & Exit
Select and confirm the option shown.
156
Individual phone configuration
Step by Step
Setting the language and country
Selecting a language
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Locality?
Select and confirm the option shown.
Speech?
Select and confirm the option shown.
Deutsch
Select and confirm the language[1] in the context menu.
Save & Exit
Confirm the option shown.
1.
The phone displays the current setting.
157
Individual phone configuration
Step by Step
You may choose from the following languages:
1. Bahasa Indonesia
2. Bahasa Malaysia
3. Brasileiro
4. Català
5. Ceština
6. Dansk
7. Deutsch
8. English
9. English(US)
10. Español
11. Français
12. Hrvatski
13. Italiano
14. Latviešu Valoda
15. Lietuvių Kalba
16. Magyar
17. Nederlands
18. Norsk
19. Polski
20. Português
21. Română
22. Slovencina
23. Slovenski Jezik
24. Srpski Jezik
25. Suomi
26. Svenska
27.
28. Türkçe
29.
30.
31.
32. Русский
33.
34.
158
Individual phone configuration
Step by Step
Country-specific setting
Adapt your phone settings to suit the country-specific
conditions (for example, transmission parameters).
z You can also configure this setting via the Web interface
Æ page 162.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the User password.
Locality
Select and confirm the option shown.
Country
Select and confirm the option shown.
Germany
Select and confirm the country [1] in the context menu.
Save & Exit
Confirm the option shown.
You may choose from the following countries:
1. Argentina
2. Australia
3. Austria
4. Belgium
5. Brazil
6. Canada
7. China
8. Chile
9. Croatia
10. Czech Republic
11. Denmark
12. Finland
13. France
14. Germany
15. Hungary
16. India
17. Ireland
18. Italy
19. Japan
1.
20. Luxembourg
21. Mexico
22. Netherlands
23. New Zealand
24. Norway
25. Poland
26. Portugal
27. Russian Federation
28. Singapore
29. Slovakia
30. South Africa
31. Spain
32. Sweden
33. Switzerland
34. Thailand
35. United Kingdom
36. United States
37. Vietnam
The phone displays the current setting.
159
Individual phone configuration
Step by Step
Network information
This information overview in the user area of the service
menu provides you with information about the IP
address or name of the phone and the HTML address
of the web-interface. It also provides real-time data
about the network activity of the phone.
N Press the key shown.
User
Select and confirm the option shown.
if nec. j Enter and confirm the user password.
Network information
Select and confirm the option shown. The following
overview opens:
Network information
Options: Exit
g
IP address: 192.168.1.9
[WBM URL http://192.168.1.
DNS domain: opera.local
LAN RX:
LAN TX:
PC RX:
PC TX:
LAN autonegotiated: Yes
LAN information: 100 Mbps full duplex
PC autonegotiated: Yes
PC information: Link down
IP Address: Displays the IP address or name which was
assigned to the phone in the network.
WBM URL: HTTP address of the Web interface. This
address is specified in the address line of the Internet
browser and is used to call the Web interface of the
phone in the browser.
DNS domain: The administrator can also assign the
phone to the IP address of a DNS domain
(for example, http://my-openStage.phone/).
160
Individual phone configuration
Step by Step
Resetting user data
The following user-specific settings changed via the
phone menu or the Web interface can be reset to factory settings.
• Display contrast
• Language setting
• Audio settings
– Volumes
– Settings
• Call lists
– All entries are deleted.
• Programmable keys
– All personalized programming is deleted (see also
Æ page 69).
Important: All data is reset without a warning tone.
Initiating the reset
v Press the key shown until the "Menu" tab is active.
User
Confirm the option shown.
if nec. j Enter and confirm the user password.
Reset
Select and confirm the option shown.
All user data...
Select and confirm "Reset all user data." The user data
is reset to factory settings.
161
Web interface (WBM)
Web interface (WBM)
General
You can configure a number of settings for your phone via the Web interface. Communication is via a secure HTTPS connection.
Calling up the Web interface
For more information on the IP address, the Web interface address,
and how to connect the telephone to the network, refer to the section entitled "Network information" Æ page 160.
To call up the interface, open a Web browser and enter the following:
https://[IP address of the phone]
[IP address of the phone] is the IP address of your phone.
https://[Name of the phone]
[Name of the phone] which was assigned by service personnel.
You might receive a certificate notification from the browser. Follow
the instructions to download the certificate.
You will be prompted to configure a user password the first time you
call up the Web interface Æ page 119. You must log on with this
password in future every time you want to open the User Pages.
Administrator Pages
This area lets you configure settings for administering your phone and the
network environment. Access to the Administrator Pages is protected by
the admin password. For more information, contact your administrator or
refer to the administration manual.
162
Web interface (WBM)
User pages
The Web interface homepage opens once you have entered and confirmed
the phone’s IP address:
User menu
User selection
Phone information
User login
Highlighted entry (current page)
Menu heading
Menu entry
1. Click a menu heading to display the individual menu entries. Click the
menu heading again to close the menu.
2. Click a menu entry to open the corresponding form.
3. Make the desired changes.
4. Click the corresponding button to save or discard your changes.
Button functions
• "Login": Log on to the phone after you have entered the user password
• "Submit": Apply changes
• "Reset": Reset original values
• "Refresh": Update the values.
• "Logout": Log off the phone
163
Web interface (WBM)
User menu
All settings that you can make via the Web interface’s user menu can also
be made via the phone’s user menu
User Pages
User login V Æ page 119
Date and Time
– Local time V Æ page 146
– Local date (day, month, year) V Æ page 146
– Allow daylight saving V Æ page 147
– Difference (minutes) V Æ page 147
– Auto time change V Æ page 148
Audio
– Ringer melody (V Æ page 152)
– Ringer tone sequence (V Æ page 153)
– Ring file (V Æ page 151)
– Room Character (V Æ page 151)
– Open listening (V Æ page 154
User Configuration
– Outgoing calls
– Autodial delay (seconds) V Æ page 87
– Allow callback: busy V Æ page 62
– Allow callback: no reply V Æ page 62
– Allow busy when dialling V Æ page 89
– Allow transfer on ring V Æ page 83
– Allow immediate dialling V Æ page 48
– Incoming calls
– Deflecting
– Allow deflection (V Æ page 71
– Default deflect destination V Æ page 71
– Deflect to DSS V Æ page 71
– Forwarding
– Settings
– Forwarding Favourites Destination 1 to Destination 5
V Æ page 71
– Forward all calls allowed V Æ page 57
– to V Æ page 55
– Forward on busy allowed V Æ page 57
– to V Æ page 55
– Forward on no reply allowed V Æ page 57
– to V Æ page 55
– No reply delay (seconds)1 V Æ page 56
– Alerts
– Visual alerts V Æ page 73
[1]. Only if "Server features" was deactivated by your administrator
164
Web interface (WBM)
– Audible alerts V Æ page 73
– Forwarding party V Æ page 59
– Handling
– Allow call waiting V Æ page 79
– Allow DND V Æ page 118
– Allow busy when dialling V Æ page 89
– CTI-Calls
– Allow auto-answer V Æ page 84
– Allow beep on auto-answer V Æ page 84
– Allow beep on auto-reconnect V Æ page 85
– Connected calls
– Allow call transfer V Æ page 82
– Allow call joining V Æ page 53
– Allow exit conference V Æ page 92
– Allow hold reminder V Æ page 75
– Hold reminder delay (minutes) V Æ page 75
– Allow music on hold V Æ page 76
– Allow conferences V Æ page 91
– Allow secure call alert V Æ page 156
– Toggle associate V Æ page 80
– Keyset
– Lines
– Ring delay (seconds) V Æ page 112
– Allow in overview V Æ page 111
– Address1
– Primary line[1]
– Ring on/off[1]
– Selection order[1]
– Overview
– Use FPK order V Æ page 113
– Add all lines V Æ page 113
– Reordering directions: Move down, Move to bottom, Move to
top, Move up V Æ page 113
– BLF
– Busy Lamp Field: not for System
[1]. Information - read only
165
Web interface (WBM)
Phone
– Display settings
– Contrast V Æ page 144
– Key module contrast V Æ page 145
– Program keys
– Normal
– Edit. V Æ page 65.
– Shifted
– Edit. V Æ page 65.
– Key Module 1 (if available such as Program keys)
– Key Module 2 (if available such as Program keys)
Locality
– Country V Æ page 159
– Language V Æ page 157
– Date format V Æ page 149
– Time format V Æ page 148
Authentication
– Old password
– New password V Æ page 119
– Confirm password
166
Fixing problems
Caring for your telephone
•
•
•
•
Never allow the telephone to come into contact with coloring, oily or
aggressive agents.
Always use a damp or antistatic cloth to clean the telephone. Never
use a dry cloth.
If the telephone is very dirty, clean it with a diluted neutral cleaner containing surfactants, such as a dish detergent. Afterwards remove all
traces of the cleaner with a damp cloth (using water only).
Never use aggressive or alcohol-based cleansers on plastic parts. The
use of scouring agents is also forbidden.
Troubleshooting
Pressed key does not respond:
If the telephone is locked repdial keys cannot be used. This also applies
when emergency numbers or predefined numbers from the dial plan are
stored on them.
Check whether you telephone is locked ("Phone locked" appears on the
screen. To unlock enter the PIN.“). If the phone is locked, unlock it.
The phone does not ring on call:
Check whether the ringtone is deactivated (see icon in the status bar on
the display Æ page 25). If it is deactivated, activate the ringtone
The displayed time is incorrect:
The time is corrected automatically over night after 24 hours at the latest.
You cannot dial a number:
Check whether your telephone is locked ("Phone locked: Enter Password"
appears on the screen). If the phone is locked, unlock it.
To correct any other problems:
First contact the relevant administrator. If the administrator are unable to
correct the problem, contact Customer Service.
167
Contact partner in the case of problems
Contact your administrator if a fault persists for more than five minutes, for
example.
Labeling keys
The following options are available for labeling the
OpenStage Key Module 15 keys with the functions assigned to them or
the saved numbers on them:
Labeling
• By hand:
Labeling strips are supplied with your OpenStage Key Module 15.
Note the function or name in the white field on the strip and insert the
strip on your OpenStage Key Module 15.
• With a computer via the Internet:
You can find the "online labeling tool" together with the user interface
at http://wiki.siemens-enterprise.com/index.php/Key_Labelling_Tool
• Select the appropriate key labeling tool in your language. You can use
the tool online via the browser or you can download it for local use.
168
Index
Index
A
Accepting calls
multi-line .................................................. 96
Administration ............................................ 34
Audio
room character ..................................... 151
volume ................................................... 150
Audio controls ............................................. 18
Audio keys ................................................... 18
Autodial delay ............................................. 87
Auto-headset .............................................. 37
B
Background lighting ................................. 144
Busy override ............................................ 102
C
Call
accepting ................................................. 36
deflecting ................................................. 70
ending ...................................................... 43
forwarding ............................................... 54
holding ...................................................... 74
incoming .................................................. 35
rejecting ................................................... 72
transferring .............................................. 81
Call forwarding chain ................................. 59
Call forwarding information ...................... 98
Call lists ........................................................ 31
Call log ......................................................... 31
Call settings
CTI calls .................................................. 151
multi-line ................................................ 111
Call waiting .................................................. 77
Callback ........................................................ 60
CE marking .................................................... 2
Conference .................................................. 90
Connection options .................................... 14
Consultation ................................................ 51
Consultation call from second call .......... 77
Context ........................................................ 48
Context menus ........................................... 26
D
Date ............................................................ 146
Dial plan ....................................................... 87
Display icons ............................................... 25
Display settings
contrast .................................................. 144
Do not disturb ........................................... 117
DSS call
call deflection ........................................ 104
DSS key
consultation ........................................... 103
indirect pickup ....................................... 104
reject call ................................................ 104
During calls
multi-line .................................................. 99
E
Executive-secretary ................................. 106
F
Forced logoff ............................................. 127
Forwarding primary line ............................ 98
Function keys .............................................. 18
G
General information ................................... 10
Graphic display ........................................... 25
call lists ..................................................... 32
icons indicating call status .................... 28
voicemail .................................................. 30
Graphic display settings
contrast .................................................. 144
Group call ..................................................... 44
H
Headset ....................................................... 70
answering call automatically ................ 37
Hot line ......................................................... 49
for lines .................................................. 101
169
Index
I
N
Icons ............................................................. 25
Immediate dialing ................................ 48, 87
Important information ................................. 3
Incoming calls
multi-line .................................................. 96
Navigator ..................................................... 19
Normal dialing ............................................. 48
K
Key module contrast ............................... 145
Key modules ............................................... 16
Keypad ......................................................... 23
L
Language setting ..................................... 157
country setting ...................................... 159
language for user prompts ................. 157
LED display
direct station selection keys ................ 20
function keys .......................................... 20
Line preview ............................................. 114
Line utilization ............................................. 21
Lines
hot/warm line ........................................ 101
Lists (for phone numbers and contacts) 95
Location of the telephone .......................... 3
Logging on and off
as a mobility user ............................. 124, 126
M
Making calls
multi-line .................................................. 97
Microphone ................................................. 43
Mobility ...................................................... 123
forced logoff .......................................... 127
logon, logoff .................................. 124, 126
Multi-line
accepting calls ........................................ 96
busy override ........................................ 102
LED display ..................................... 22, 105
Multi-line telephone ................................... 12
170
O
Open listening ............................................ 42
OpenScape Voice ..................................... 128
abbreviated dialing
two-key abbreviated dialing ............ 134
accepting anonymous calls ................ 133
call tracing .............................................. 134
feature toggle key ................................ 128
Functions ............................................... 128
list for selective calls ........................... 131
making anonymous calls ..................... 129
parallel call ............................................. 138
parking .................................................... 140
reachability ............................................ 137
rejecting anonymous calls .................. 133
serial call ................................................ 137
silent monitoring ................................... 141
OpenScape Voice hunt group ................ 135
OpenStage Key Module 40 ...................... 16
Operating instructions ................................. 2
Overview tab .................................... 107, 110
P
Padlock icon ................................................ 35
Parallel call ................................................. 138
Parking ....................................................... 140
Pattern melody ......................................... 152
Pattern sequence ..................................... 153
Phantom line ............................................... 21
Phone number directories ........................ 95
Phone settings .......................................... 144
Picking up the held call
................................................................... 39
Pop-up menu .............................................. 28
Primary line ................................................. 21
Privacy ........................................................ 116
Private line ................................................... 21
Program/Service menu ............................. 33
Programmable sensor keys ............... 20, 64
Index
R
U
Reachability ............................................... 137
Redial ........................................................... 50
Redialing
multi-line .................................................. 98
Repdial keys ................................................ 86
Ringer off ................................................... 116
User interface ............................................. 13
User support ............................................... 11
Using Ethernet switches .......................... 15
Using network ports more efficiently ..... 15
S
Second call .................................................. 77
ignoring .................................................... 77
rejecting ................................................... 78
Second call with consultation call ........... 77
Secondary line ............................................ 21
Security ...................................................... 116
Sensor keys
immediate ring ........................................ 68
resetting ................................................... 69
Serial call .................................................... 137
Set headset port ...................................... 155
Settings ...................................................... 144
Shared line .................................................. 21
Silent monitoring ...................................... 141
Single-line telephone ................................. 12
Speakerphone distance .............................. 3
Speakerphone mode ........................... 36, 40
Status icons ................................................ 25
W
Warm line .................................................... 49
for lines .................................................. 101
Web interface ........................................... 162
T
Telephone maintenance ......................... 167
Telephony interface
single line ................................................. 28
Time ........................................................... 146
Time display format ................................. 148
Toggle/Connect .......................................... 52
Troubleshooting ....................................... 167
Trunk keys ................................................... 21
171
Copyright © Siemens Enterprise
Communications GmbH & Co. KG
Hofmannstr. 51
80200 München
Deutschland
Siemens Enterprise
Communications GmbH & Co. KG
is a Trademark Licensee of Siemens AG
Reference No:
A31003-S2010-U101-22-7619
Communication for the open minded
Siemens Enterprise Communications
www.siemens.com/open
The information provided in this document
contains merely general descriptions or characteristics of performance which in case of
actual use do not always apply as described
or which may change as a result of further
development of the products.
An obligation to provide the respective characteristics shall only exist if expressly agreed
in the terms of contract. Availability and
technical specifications are subject to
change without notice. OpenScape,
OpenStage and HiPath are registered trademarks of Siemens Enterprise
Communications GmbH & Co. KG.
All other company, brand, product and service names are trademarks or registered
trademarks of their respective holders.