Bosch VIP XD Installation guide

VIP XD HD
VIP-XDHD
en
Installation Guide
VIP XD HD
Table of Contents | en
3
Table of Contents
1
Safety
5
1.1
Electric shock hazard
5
1.2
Installation and operation
5
1.3
Maintenance and repair
5
1.4
Software
5
2
Short information
6
2.1
About this manual
6
2.2
Conventions in this manual
6
2.3
Intended use
6
2.4
EU Directives
6
2.5
Rating plate
6
3
System overview
7
3.1
Parts included
7
3.2
Overview of functions
7
3.3
Connections, controls and displays
9
4
Installation
10
4.1
Preparations
10
4.2
Mounting
11
5
Connection
12
5.1
Sequence of connections
12
5.2
Monitor
12
5.3
Network
12
5.4
Power
12
5.5
Power on/power off
13
6
Configuration
14
6.1
Setup
14
6.2
Setup using Bosch Video Client
14
7
Troubleshooting
15
7.1
General malfunctions
15
7.2
Power light and LEDs
15
8
Maintenance
16
8.1
Updates
16
8.2
Repairs
16
9
Setting out of order
17
9.1
Transfer and disposal
17
Bosch Sicherheitssysteme GmbH
Installation Guide
F.01U.217.838 | V2 | 2011.08
4
10
en | Table of Contents
VIP XD HD
Technical data
18
10.1
Electrical
18
10.2
Mechanical
18
10.3
Environmental conditions
18
10.4
Certifications and approvals
18
10.5
Standards
19
F.01U.217.838 | V2 | 2011.08
Installation Guide
Bosch Sicherheitssysteme GmbH
VIP XD HD
Safety | en
1
Safety
1.1
Electric shock hazard
–
5
Never attempt to connect the unit to any power network other than the type for which it
is intended.
–
Use only the power supply unit that is included.
–
Connect the unit to an earthed mains socket-outlet.
–
Never open the housing.
–
Never open the housing of the power supply unit.
–
If a fault occurs, disconnect the power supply unit from the power supply and from all
other units.
–
Install the power supply and the unit only in a dry, weather-protected location.
–
If safe operation of the unit cannot be ensured, remove it from service and secure it to
prevent unauthorized operation. In such cases, have the unit checked by Bosch Security
Systems.
Safe operation is no longer possible in the following cases:
1.2
–
if there is visible damage to the unit or power cables,
–
if the unit no longer operates correctly,
–
if the unit has been exposed to rain or moisture,
–
if foreign bodies have penetrated the unit,
–
after long storage under adverse conditions, or
–
after exposure to extreme stress in transit.
Installation and operation
–
The relevant electrical engineering regulations and guidelines must be complied with at
all times during installation.
–
Relevant knowledge of network technology is required to install the unit.
–
Before installing or operating the unit, make sure you have read and understood the
documentation for the other equipment connected to it, such as monitors. The
documentation contains important safety instructions and information about permitted
uses.
–
Perform only the installation and operation steps described in this manual. Any other
actions may lead to personal injury, damage to property or damage to the equipment.
1.3
Maintenance and repair
–
Never open the housing of the unit. The unit does not contain any user-serviceable parts.
–
Never open the housing of the power supply unit. The power supply unit does not contain
any user-serviceable parts.
–
Ensure that all maintenance or repair work is carried out only by qualified personnel
(electrical engineers or network technology specialists).
CAUTION!
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries
according to the instructions.
1.4
Software
–
VIP XD HD may only be operated with the installed software products.
–
It is not allowed to install additional software.
Bosch Sicherheitssysteme GmbH
Installation Guide
F.01U.217.838 | V2 | 2011.08
6
en | Short information
VIP XD HD
2
Short information
2.1
About this manual
This manual is intended for persons responsible for the installation and operation of the
VIP XD HD decoder. International, national and any regional electrical engineering regulations
must be followed at all times. Relevant knowledge of network technology is required. The
manual describes the installation and operation of the unit.
2.2
Conventions in this manual
In this manual, the following symbols and notations are used to draw attention to special
situations:
CAUTION!
This symbol indicates that failure to follow the safety instructions described may endanger
persons and cause damage to the unit or other equipment.
It is associated with immediate, direct hazards.
NOTICE!
This symbol refers to features and indicates tips and information for easier, more convenient
use of the unit.
2.3
Intended use
The VIP XD HD High Definition video decoder receives and decodes video signals over data
networks (Ethernet LAN, Internet) and displays High Definition and Standard Definition video
from cameras and encoders using H.264 or MPEG-4 encoding at up to 30 images per second.
The unit is intended for use with CCTV systems. Other applications are not permitted.
In the event of questions concerning the use of the unit which are not answered in this
manual, please contact your sales partner or:
Bosch Sicherheitssysteme GmbH
Werner-von-Siemens-Ring 10
85630 Grasbrunn
Germany
www.boschsecurity.com
2.4
EU Directives
The VIP XD HD High Definition video decoder complies with the requirements of EU Directives
89/336 (Electromagnetic Compatibility) and 73/23, amended by 93/68 (Low Voltage
Directive).
2.5
Rating plate
For exact identification, the model name and serial number are inscribed on the bottom of the
housing. Please make a note of this information before installation, if necessary, so as to have
it to hand in case of questions or when ordering spare parts.
F.01U.217.838 | V2 | 2011.08
Installation Guide
Bosch Sicherheitssysteme GmbH
VIP XD HD
System overview | en
3
System overview
3.1
Parts included
–
VIP XD HD High Definition video decoder
–
1 international power supply unit with EU and US power cord
–
4 screw-on stands
–
1 monitor mounting kit
–
1 Installation Manual
–
Adhesive MAC address labels
7
NOTICE!
Check that the delivery is complete and in perfect condition. Arrange for the unit to be
checked by Bosch Security Systems if you find any damage.
3.2
Overview of functions
High Definition video decoder
The VIP XD HD decoder displays high definition and standard definition video from cameras
and encoders using H.264 or MPEG-4 encoding at up to 30 images per second over IP
networks. It can decode four H.264 720p30 streams at 10 Mbps or two 1080p30 streams at
10 Mbps. Alternatively, it can simultaneously decode six H.264 Standard Definition streams at
up to 6 Mbps from fast-moving AutoDome cameras with the highest clarity. When H.264
Standard Definition streams at up to 2.5 Mbps from medium activity scenes are connected, up
to twelve streams can be displayed.
The VIP XD HD decoder can drive a HD display directly, and so is ideally suited for
applications with flat-screen monitor walls. Compact in size in relation to its decoding power,
VIP XD HD is perfect for any display application that requires space-saving solutions.
Remote control
Control the viewing mode remotely and establish the video connections using Bosch’s
comprehensive video management systems.
Operating system
VIP XD HD is based on the latest Intel H67 Express Chipset on a Mini-ITX board with a Core i3
CPU running at 3.1 GHz. The system has a 8 GB Flash module as boot medium for operating
system and application. It uses a Gigabyte Ethernet port.
The system runs a tailored and Bosch-branded Microsoft Windows 7 Embedded operating
system, and Monitor Wall software based on HD-capable VideoSDK 5, both finetuned for High
Definition video decoding support. The VIP XD HD decoder provides three monitor outputs,
DVI-I, HDMI and DP; only one of these can be used at the same time.
Bosch Sicherheitssysteme GmbH
Installation Guide
F.01U.217.838 | V2 | 2011.08
8
en | System overview
VIP XD HD
High performance
Transmit High Definition IP video to a high-performance VIP XD HD decoder and present it
with ultimate clarity on a large, flat-screen HD monitor, for example, a high-performance 26"
or 42" Bosch HD LCD monitor. VIP XD HD is capable of decoding two full HD 1080p30
streams or four 720p30 streams, for example, displayed in quad view. It can handle up to six
Standard Definition streams at up to 6 Mbps with full resolution and frame rate, and display it
in a 2 × 3 view on a 16:9 monitor. At a lower resolution, bit rate, or frame rate, VIP XD HD is
capable of displaying up to 30 video streams in a 5 × 6 view, arranged in various selectable
screen layouts.
Layouts can be switched at any time during operation, initiated by the controlling video
management system. Layout switching can be based on alarm scenarios.
Access security
VIP XD HD decoders offer various security levels for accessing the network, the unit, and the
data channels. System access is password-protected with two levels. For total data
protection, each communication channel can be independently AES encrypted with 128 bit
keys, once the encryption site license has been applied.
Easy upgrade
Remotely upgrade the VIP XD HD decoders whenever new software becomes available. This
ensures up-to-date products, thus protecting investment with little effort.
Summary
The VIP XD HD High Definition decoder provides the following main functions:
–
Receiving and decoding video and data over IP data networks
–
H.264 or MPEG-4 decoding at up to 30 images per second
–
Decoding of four H.264 High Definition streams with 720p30 at 10 Mbps or two streams
–
Decoding of up to six H.264 Standard Definition streams at up to 6 Mbps at the same
–
Integrated Ethernet port (10/100/1000 Base-T)
–
Configuration and remote control of all internal functions via TCP/IP, also secured via
–
Password protection to prevent unauthorized connection or configuration changes
–
Convenient maintenance via uploads
with 1080p30 at 10 Mbps at the same time
time
HTTPS
F.01U.217.838 | V2 | 2011.08
Installation Guide
Bosch Sicherheitssysteme GmbH
VIP XD HD
3.3
System overview | en
9
Connections, controls and displays
1
2
3
4
5
6
7
8
9
10
11
1
Power supply socket
for connecting the power supply unit that is included
2
USB ports
3
RJ45 socket
for connecting to an Ethernet LAN (local network), 10/100/1000 MBit Base-T
4
eSATA port
disabled
5
USB ports
6
DVI-I monitor socket
for connecting a monitor via DVI-I cable
7
HDMI monitor socket
for connecting a monitor via HDMI cable
8
USB ports
9
DP monitor socket
for connecting a monitor via DP cable
10
Audio connections (mono)
unused
11
Main switch
for switching the unit on and off, lights up blue when the unit is switched on
NOTICE!
For more information about the LEDs, see Section 7.2 Power light and LEDs, page 15.
Bosch Sicherheitssysteme GmbH
Installation Guide
F.01U.217.838 | V2 | 2011.08
10
en | Installation
VIP XD HD
4
Installation
4.1
Preparations
CAUTION!
VIP XD HD and the power supply unit are both intended for use indoors only.
Select a suitable location for installation that guarantees to meet the environmental
conditions. The ambient temperature must be between 0 and +40 °C (+32 and +104 °F). The
relative humidity must not exceed 90%.
VIP XD HD and the power supply unit generate heat during operation, so you should ensure
that there is adequate ventilation and enough clearance between both units and heat-sensitive
objects or equipment. Please note the maximum heat value of 460 BTU/h for the VIP XD HD
decoder.
Please ensure the following installation conditions:
–
Do not install VIP XD HD or the power supply unit close to heaters or other heat sources.
Avoid locations exposed to direct sunlight.
–
All ventilation openings must be kept free from blockings. Do not stack several units one
on top of each other. Do not put any unit to an upright position.
–
Allow sufficient space for running cables.
–
Ensure that both VIP XD HD and the power supply unit have adequate ventilation.
–
When making connections, use only the cables supplied or use appropriate cables
immune to electromagnetic interference.
–
Position and run all cables so that they are protected from damage, and provide
adequate cable strain relief where needed.
–
Avoid impacts, blows and severe vibrations that exceed the specification limits (see
Section 10 Technical data, page 18), as these can irreparably damage the VIP XD HD
decoder.
F.01U.217.838 | V2 | 2011.08
Installation Guide
Bosch Sicherheitssysteme GmbH
VIP XD HD
4.2
Installation | en
11
Mounting
You can mount the VIP XD HD decoder to an approved monitor using the supplied mounting
kit.
CAUTION!
The mounting location must be able to reliably hold the unit. The load-bearing capacity must
be adequate for four times the weight of the unit.
If mounting the unit to the back of a monitor, use only monitors that are approved by Bosch
Security Systems.
When mounting the unit on the rear side of a monitor, ensure that there is adequate
ventilation and enough clearance between both units and walls or other monitors, especially
with several monitors mounted side by side on a wall.
NOTICE!
You can obtain a list of approved monitors from your supplier or directly from Bosch Security
Systems. This list is constantly being updated and extended.
As an alternative you can screw on the four stands supplied to the bottom of the VIP XD HD
decoder and place the unit upon an appropriate flat surface from which it cannot fall down.
Bosch Sicherheitssysteme GmbH
Installation Guide
F.01U.217.838 | V2 | 2011.08
12
en | Connection
VIP XD HD
5
Connection
5.1
Sequence of connections
CAUTION!
Do not connect the VIP XD HD decoder to the power supply until all other connections have
been made. Otherwise the automatic assignment of the IP address will fail and a faulty
monitor resolution will be set. The may lead to serious damage of the unit.
5.2
Monitor
NOTICE!
You can obtain a list of approved monitors from your supplier or directly from Bosch Security
Systems. This list is constantly being updated and extended.
You must connect a suitable monitor to the VIP XD HD decoder. The unit provides three
monitor outputs, DVI-I, HDMI and Display Port. You can select one of the monitor outputs for
the connection. The simultaneous use of several outputs is not possible.
CAUTION!
When connecting a monitor to the DVI-I output, do not use a DVI-to-VGA adapter.
The monitor must be equipped with a DVI input.
5.3
1.
Connect the monitor to the DVI-I monitor socket using a monitor cable with DVI-I plugs.
2.
As an alternative both of the other monitor sockets (HDMI or DP) can be used.
Network
You must connect the VIP XD HD decoder to a 10/100/1000 Base-T network using a standard
UTP category 5 cable with RJ45 plugs. If a network connection has been set up correctly, the
LEDs on the RJ45 socket light up. A flashing LED signals that data packages are being
transmitted over the network.

5.4
Connect the unit to the network via the RJ45 socket.
Power
Power is supplied via a separate power supply unit that is part of the delivery.
CAUTION!
Use only the power supply unit that is included, together with the suitable power cord.
Connect the unit to an earthed mains socket-outlet.
Do not connect the VIP XD HD decoder to the power supply until all other connections have
been made.
1.
2.
Connect the VIP XD HD decoder to the power supply unit.
Select the suitable power cord and plug this into the power supply unit and then into the
mains.
The unit is now ready for use.
F.01U.217.838 | V2 | 2011.08
Installation Guide
Bosch Sicherheitssysteme GmbH
VIP XD HD
5.5
Connection | en
13
Power on/power off
VIP XD HD is equipped with a power switch on its front panel.
1.
Press the power switch on the front once to switch on the unit. The blue light inside the
switch lights up.
2.
To switch off press the power switch again. The blue light turns off.
3.
Switch on the monitor in order to see the user interface after the boot-up procedure.
NOTICE!
All information regarding the functions and the operation can be found in the relevant
documentation of Monitor Wall, Bosch Video Management System, or Bosch Video Client.
Bosch Sicherheitssysteme GmbH
Installation Guide
F.01U.217.838 | V2 | 2011.08
14
en | Configuration
VIP XD HD
6
Configuration
6.1
Setup
The setup procedure is carried out via Bosch Video Client or other management systems. You
must at least assign a valid IP address to operate on your network.
NOTICE!
All information regarding the configuration can be found in the relevant documentation of the
video management system in use.
6.2
Setup using Bosch Video Client
The Bosch Video Client program can be downloaded from the product catalog on the Bosch
Web site. This program allows you to implement and set up VIP XD HD in the network quickly
and conveniently.
Installing the program
1.
Download Bosch Video Client from the product catalog on the Bosch Web site to the
computer with which you want to set up VIP XD HD.
2.
Follow the instructions on the screen to complete the installation.
Configuring VIP XD HD
You can start Bosch Video Client immediately after installation.
1.
Double-click the
icon on the desktop to start the program. Alternatively, start the
application via the Start button and the Programs menu (path: Start/Programs/Bosch
Video Client/Bosch Video Client).
2.
Click
to open the Configuration Manager application. After the application has
started, the network is immediately searched for compatible units.
3.
You can start the configuration if your VIP XD HD is shown in the list in the left section of
the window. To do this, right-click the entry for the unit.
4.
Click Device Network Settings... in the popup menu.
5.
In the Device IP address field, enter a valid IP address to operate on your network (for
example 192.168.0.10) and click OK. A software restart is triggered automatically and the
IP address is valid.
6.
If required, enter an appropriate subnet mask for the IP address, and additional network
data and click OK.
Software restart
You can trigger the software restart directly with the assistance of Configuration Manager.

Right-click the entry for the unit in the list in the left section of the window and select the
Reset command from the context menu.
Additional parameters
You can check and set additional parameters with the assistance of Configuration Manager.
You can find detailed information on this in the documentation for this program.
F.01U.217.838 | V2 | 2011.08
Installation Guide
Bosch Sicherheitssysteme GmbH
VIP XD HD
Troubleshooting | en
7
Troubleshooting
7.1
General malfunctions
15
If you are unable to resolve a malfunction, please contact your supplier or systems integrator,
or go directly to Bosch Security Systems Customer Service.
The following tables are intended to help you identify the causes of malfunctions and correct
them where possible.
Malfunction
Possible causes
Recommended solution
No image display.
Monitor settings.
Check the input selection at the
monitor.
Faulty cable connections.
Check all cables, plugs and
connections.
Monitor fault.
Connect another monitor to the
unit or use another monitor
connection.
The unit is not
Power failure during
Have the unit checked by
operational after a
programming by firmware file.
Customer Service and replace if
necessary.
firmware upload.
Incorrect firmware file.
Have the unit checked by
Customer Service and replace if
necessary.
The power light is not lit. Unit not switched on.
Press the main switch on the
front panel.
Unit not connected to the power Check all cables, plugs and
7.2
supply unit.
connections.
Power supply unit not
Check all cables, plugs and
connected to the mains outlet.
connections.
Power light and LEDs
VIP XD HD has a light inside the power switch on its front and two LEDs on the RJ45 socket
on the rear that show the operating status:
Power light
Off:
VIP XD HD is switched off or not connected to the power
Lights up blue:
VIP XD HD is switched on
RJ45 socket LEDs
Left LED:
Off: LAN connection not established
Green: LAN connection established
Blinking green: LAN activity occurring
Right LED:
Off: 10 Mbps data rate
Green: 100 Mbps data rate
Yellow: 1000 Mbps data rate
Bosch Sicherheitssysteme GmbH
Installation Guide
F.01U.217.838 | V2 | 2011.08
16
en | Maintenance
VIP XD HD
8
Maintenance
8.1
Updates
Software updates are carried out via Configuration Manager or other management systems in
use. Please refer to the relevant documentation.
8.2
Repairs
CAUTION!
Never open the housing of the VIP XD HD decoder. The unit does not contain any userserviceable parts.
Never open the housing of the power supply unit. The power supply unit does not contain any
user-serviceable parts.
Ensure that all maintenance or repair work is carried out only by qualified personnel
(electrical engineers or network technology specialists). In case of doubt, contact your
dealer's technical service center.
F.01U.217.838 | V2 | 2011.08
Installation Guide
Bosch Sicherheitssysteme GmbH
VIP XD HD
Setting out of order | en
9
Setting out of order
9.1
Transfer and disposal
17
VIP XD HD should only be passed on together with this installation and operating manual.
Your Bosch product is designed and manufactured with high-quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should be
disposed of separately from your household waste.
In the European Union, there are separate collection systems for used electrical and
electronic products. Please dispose of this equipment at your local community waste
collection/recycling center.
Bosch Sicherheitssysteme GmbH
Installation Guide
F.01U.217.838 | V2 | 2011.08
18
en | Technical data
VIP XD HD
10
Technical data
10.1
Electrical
10.2
Power supply
Wide-range, external, included in the box
Input voltage
100 to 240 VAC, 50/60 Hz
Power consumption
Approx. 90 W, 135 W max.
Mechanical
Dimensions (H × W ×D)
58 × 225 × 217.8 mm (2.283 × 8.858 × 8.575 in)
Weight
Approx. 3 kg (6.6 lb)
VESA mount
75 × 75 mm or 100 × 100 mm
(2.953 × 2.953 in or 3.937 × 3.937 in)
Video
1 of 3 outputs, connector DVI-I, or HDMI, or DP, no VGA support
Front indicator
1 × power switch with integrated blue LED
Rear connectors
1 × power connector
6 × USB
1 × Ethernet port
1 × DVI-I monitor output
1 × HDMI monitor output
4 × audio connector, unused
10.3
10.4
Environmental conditions
Operating temperature
0 °C to +40 °C (+32 °F to +104 °F)
Relative humidity
0 to 90% atmospheric humidity, non-condensing
Thermal value
Approx. 310 BTU/h, 460 BTU/h max.
Certifications and approvals
Safety
IEC 60950
Electromagnetic
EN55022
compatibility
EN55024
FCC 47 CFR Chapter 1 Part 15
F.01U.217.838 | V2 | 2011.08
Installation Guide
Bosch Sicherheitssysteme GmbH
VIP XD HD
10.5
Technical data | en
19
Standards
Video
H.264 (ISO/IEC 14496-10), MPEG-4
Video data rates
HD: up to 20 Mbps, single stream
SD: up to 6 Mbps per stream
GOP structure
I, IP, IBBP
Monitor resolutions
DVI-I: 1920 × 1200 max. (WUXGA) at 60 Hz
HDMI: 1920 × 1200 max. (WUXGA) at 60 Hz
DP: 2560 × 1600 max. (WQXGA) at 60 Hz
Ethernet
10/100/1000 Base-T, auto-sensing, half/full duplex, RJ45
Protocols
RTP, Telnet, UDP, TCP, IP, HTTP, HTTPS, FTP, DHCP, IGMP V2/
V3, ICMP, ARP, SMTP, SNTP, SNMP (V1, MIB-II)
Encryption
Bosch Sicherheitssysteme GmbH
TLS 1.0, SSL, AES (optional)
Installation Guide
F.01U.217.838 | V2 | 2011.08
20
en | Technical data
F.01U.217.838 | V2 | 2011.08
VIP XD HD
Installation Guide
Bosch Sicherheitssysteme GmbH
Bosch Sicherheitssysteme GmbH
Werner-von-Siemens-Ring 10
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2011