advertisement
▼
Scroll to page 2
of 4
Pulse LE - Ref. PLS200 QUICK START GUIDE Thank you for choosing Analog Way and the Pulse LE. By following these simple steps, you will be able to setup and use your powerful Scaler/Switcher within minutes. Discover the Pulse LE extensive capabilities and intuitive interface while configuring your first show, and unleash your creativity for a new experience in show and event management by Analog Way. What’s in the box 1 x Pulse LE (PLS200) 1 x Power supply cord 2 x DVI male to HD15 female and DVI-D female breakout cable 1 x HD15 to 5 BNC cable 1 x Ethernet cross cable (for device update) 1 x Set of 3 audio 5-pin screw terminals 4 x Screws for handle removal (M4x12mm) WARNING ! If required, front handles of the device can be dismantled, but with caution. The original screws removed must not be reintroduced to their location without handles in place. Substantial damages can occur, including risk of electric shock from the mains voltage. Only M4x12mm screws can be used. (They are supplied with the unit) 1 x RCS - Remote Control Software (for PC only) * 1 x User Manual (PDF version) * 1 x Quick Start Guide (PDF version) * * Download on our website: www.analogway.com Quick install and setup Getting started: You may wish to reset the unit to factory settings to get started. Go to: Menu --> Control --> Default Values --> Yes. 4. To display a PIP, select the PIP layer (it will begin to blink) then select your source (it will also blink). Press [TAKE] to display the PIP on program output. 1. Select the Output resolution that matches the native resolution of your display. You will next be prompted to choose enable follow mode if desired and output rate. To see the layer beneath, you will need to clear or move the layers that are on top. enu --> Output --> Output format --> 1024x768 --> M Internal Ref --> 60 Hz. 2. Inputs can be configured automatically using the Auto Set All function. Menu --> Intputs --> AutoSet All --> Yes. It will scan each input and detect the sync type that is plugged in. You can still do an Autoset or manual setup per input. The Pulse LE has 2 layers available called: [BACKGROUND LIVE], and [PIP]. Each layer will obscure your view other layers below. 3. To display a source, Select the [BACKGROUND LIVE] layer (it will begin to blink) then, select a source (it will also blink). Press [TAKE] to transition your source from preview to program output. There will always be a layer selected (blinking) and a source selected (blinking) to the selected layer (blinking). To view on preview or change the contents of a different layer, simply select it. Only 1 layer can be seen on the preview at a time. 5. To clear the PIP or any other layer, select the layer (it will blink) then, select [BLACK]. Press [TAKE] to remove the layer from the program output. *TIP* If you would like the Program and Preview to toggle/ flipflop during each Take, enable this feature by going to Menu --> Control --> Preset Toggle. Once enabled, everything on the Program output will become the Preview during each Take. PLS200 can be used to display: - sources seamlessly switched in the Background Live layer. - 1 PIP over the Background Live layer. - 2 PIPs over the Background Color (Split Screen). IMPORTANT: Simply selecting a menu item will not set it to that value. Be sure to press the ENTER button when parametering the menu items. Pulse LE - Ref. PLS200 Front Panel Description LAYERS Press to select a layer, then choose an input. PRESET: Recall a custom stored preset (4 memories available). To store a preset, use Menu -> Preset. PIP: Display a live source Bkgnd Live: Display a live source FREEZE: Freeze the input linked to the current layer on MAIN EFFECT LAYER HIERARCHY Select a custom transition PIP Background Live TAKE Transition the pre-selected sources onto the MAIN output with the selected effects CONTROL EXIT/MENU: Home Menu or back one level ENTER: Validates the menu or command INPUT SELECTION #1 to #6: Press to access analog source #1 to #6 DVI 1 to DVI 2: Press to access DVI #1 or DVI #2 SDI 1 to SDI 2: Press to access SDI #1 or SDI #2 BLACK: Clear the active layer STAND-BY Hold for 3 seconds for stand-by Mode BUTTON COLOR USAGE O P E R AT I O N S O V E R V I E W INPUT SETUP Solid red: #1 = Source is on the main outputs #2 = Freeze enable #3 = Stand-by button #4 = Preset Selection WORKING IN MIXER MODE Solid green: #1 = Source is on Preview #2 = Function available for modification Blinking red: Layer/source selected, and is currently active on the main output Blinking green: Layer/source selected, and is not currently active one the main output 1- Press the [EXIT/Menu] button from the Home menu (all functions must be confirmed by the [Enter] button) 2- Press Input and Autoset ALL 3- If the acquisition has failed, check all connections and perform a manual setup 4- For a comprehensive Input Setup, please refer to user’s Manual 5- For a manual input setup, press the [EXIT/Menu] button: a) Select Input menu, b) Select an input from Input #1 up to SDI #2, then c) Select Type. NOTE: To adjust input Size or Pos, use the Layer Menus. To adjust Blanking, use the Auto-Centering or Blanking adjustments in the Image menu. 1- S elect Background Live Button then select your INPUT. 2- On the preview screen, the input appears 3- Select an [EFFECT] (open/close) 4- Press [TAKE] to view the result on the Main screen 5- Try enabling the ‘Preset Toggle’ from the Control menu to have your preview replaced by program during each Take WORKING WITH PIPs IN MIXER MODE 1- Press the [PIP] button. On the preview screen, the PIP (layer) appears as a color rectangle 2- Select an input. On the preview screen, the input appears in the layer rectangle 3- Adjust the PIP (layer) with Layer menu (Pos & Size or Zoom) 4- Select a transition (open/close) or an effect into “Layer menu” 5- Press [TAKE] to view the result on the main screen 6- To remove layer, press [BLACK] then [TAKE] 7- For another PIP setup, repeat from step #1 OUTPUT SETUP 1- P ress the [EXIT/Menu] button from the Home menu (all functions must be confirmed by the [Enter] button) 2- Select Output menu 3- Select Output format menu 4- On Format line, select the display’s native resolution, select the rate 5- Control or adjust your display device (Monitor or Video Projector) 6- If necessary, select Test Pattern in the Output menu Pulse LE - Ref. PLS200 Rear Panel Description WORKING WITH PLS200 The features of PLS200 can be controlled by the external remote control as: - Orchestra - Ref. ORC50 - Axion2 - Ref. ARC200 - Remote Control Software - Ref. RCS (supplied) - Triple Remote Control Keypad - Ref. TRK-800 - Remote Control Keypad - Ref. RK-300 RS-232 communication port on a DB9 female connector IP-LAN connector 3G-SD/HD-SDI inputs #1 & #2: female BNC Universal Analog Computer TV/HDTV inputs #1 to #4 Power supply: IEC/EN/UL/CSA 60950-1, internal, autoswitchable HOME MENU (extract) Auto Centering (R1) Blanking Adjust (A3) displayed when an input is active (R1) Analog Computer Input (R2) Analog Input (R3) Video Input (R4) EDTV/HDTV Input (R5) RGB or YUV or YC or CV (R6) NTSC Input (R7) Interlaced 50 Hz (R8) Interlaced 60 Hz (R9) SDTV * Motion Correction The Menu allows to improve the threshold of the comb filter. 0% means no adjustments and 100% is the max. The setting is manual with a visual correction. The result is the removal of the aliasing in the moving picture. Outputs #1 & #2: female HD15, DVI-I (simultaneous analog and digital outputs) MCO Male connector for input. DVI #1 & #2 and AUX AUDIO OUTPUT Main Audio Output (balanced) DVI connectors: DVI-D inputs #1 and #2 on the DVI-I digital pins, and Universal Analog inputs #5 & #6 on the DVI-I analog pins. Use the included break-in cable HOW TO ADJUST A SOURCE? IMAGE (A3) 3.5mm Jack Stereo Connector input (unbalanced) (R2) Cropping (R2) Optimize (R1) Under/Over (R3) Aspect IN Aspect OUT Colorimetry Advanced (R2) 2:2 Pulldown (R7) 3:2 Pulldown (R8) Force 4:3 (R9) Reset settings H position V position H size V size... H position V position H size V size... Phase H Total Underscan Overscan Native LetterBox_1_78 LetterBox_2_35 Anamorphic Pillar Box Full screen Centered Cropped 1_1 Brightness Contrast Color Hue (R6) Component Level (R2) Motion Correct. (R11) * Red Level (R5) Green Level (R5) Blue Level (R5) HOME MENU AUDIO INPUT/OUTPUT CONNECTIONS The Home Menu is the system’s top level menu, from which all others menus can be accessed. To access a menu, press the [Menu] button. To navigate in the Home Menu, please use the knob. To confirm, please use the [Enter] button. You can also return to the Home Menu by pressing the [Exit] button. MCO male connectors Inputs #1 to #4: Unbalanced connection - INPUT: configure the 10 individual input types and resolutions - MAIN OUT: set format and rate of Main output - PREVIEW OUT: set format and rate of Preview output - PRESET: store and use presets - IMAGE: change source image settings of an input - KEYING/TITLING: access keying and titling controls and parameters for the selected layer - LAYER: adjust Layer size, position, border transparency or Transition - AUDIO: access all audio input and output parameters - CONTROL: access device software information, LAN settings, reset factory settings, amongst other user oriented functions (see next page) - VIRTUAL T-Bar: access the Virtual T-Bar Right Left Ground Inputs DVI1 & DVI2: Unbalanced connection Input (AUX): Balanced connection 4 L DVI 1 R DVI1 Left DVI 1 Right DVI 1 GROUND(S) Left DVI 2 Right DVI 2 L DVI 2 R DVI 2 UNBALANCED Main Output: Balanced connection L+ L- L+ L- GROUND(S) R+ R- R+ RBALANCED How to do an AutoTake? HOME MENU (extract) CONTROL AutoTake Enabled or disabled The Autotake function performs a TAKE automatically each time an input is selected. SynchLoss function CONTROL SynchLoss Select input This SynchLoss funtion allows you to choose a backup source in the case where one of your input will be disconnected. The designed source will replace automatically the unplugged source. How to disable the HDCP encryption? HOME MENU (extract) INPUT DVI1 or DVI2 HDCP enable Enabled or disabled HOME MENU (extract) MAIN OUT PREVIEW OUT HDCP Detection Disabled Automatic The HDCP Encryption can be disabled on DVI inputs #1 to #2 or/and Main Output / Preview Output. This can be useful when you have a computer which is detecting the HDCP compliance of your switcher and protecting the content by encrypting the signal from this computer. This feature will disable the HDCP compliance on this specific DVI input only. If you want to use HDCP content from your sources, be sure to use only HDCP compliant screens or projector. If it’s not the case, the output image could be disabled. Screen will go to black without displaying the HDCP input image, or partially layer out on HDCP content. The output status can provide you all information about the output in real time. This feature is particularly useful when HDCP is used with long cable to be sure the communication is well handled. How to use the Auto-Lock Function? HOME MENU (extract) CONTROL Auto-Lock Enabled or disabled [Auto-Lock] allows to select an input only if a signal is connected. Warranty This Analog Way product has a 3 year warranty on parts and labor, back to factory. This warranty does not include faults resulting from user negligence, special modifications, electrical surges, abuse (drop/crush), and/or other unusual damage. Going further with the Pulse LE For complete details and operations procedures, please refer to the Pulse LE User’s Manual and our website for further information: www.analogway.com Version : 4.00 - 28/12/2011 Code : 140108
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement