Duerkopp Adler 4180i Service Manual

Instructions for service
4180i - 5
Minerva Boskovice, a.s., Sokolská 60, CZ - 680 17 Boskovice
Tel.: +420-516-453434, 453433, 494111
Fax: +420-516-452165
Edition: 09/2004
Printed in Czech Republic
http://www.minerva-boskovice.com
S735 000621
CONTENTS:
1. General safety instructions ............................................................................................................................................... 1
2. Introduction .......................................................................................................................................................................... 1
3. Head of the sewing machine .............................................................................................................................................. 2
..
3. 1 Hook and hook post ................................................................................................................................................................ 2
3.1.1 Description
3.1.2 Height setting of the hook
3.1.3 Setting the distance of the hook from the needle
3.1.4 Angular setting of the hook (timing)
3.1.5 Protection of the needle and of the hook point
3.1.6 Setting of the bobbin case opener
3.1.7 Setting the regulation of the hook lubrication
3.1.8 Replacement of the hook
3.1.9 Setting the gear
3.1.10 Dismantling of the hook post
3.2
3.3
3.4
3.5
3.6
Needle and thread mechanism ................................................................................................................................. 5
3.2.1 Description
3.2.2 To check the handwheel angular adjustment
3.2.3 Height setting of the needle bar
3.2.4 Angular setting of the pin of the thread mechanism
3.2.5 Side setting of the needle bar holder
3.2.6 Setting the needle (the needle bar holder) in the direction of sewing
Throat plate and its post ........................................................................................................................................................ 7
3.3.1 Description
3.3.2 Mounting and removing the throat plate and its insert
3.3.3 Setting the throat plate and its insert
3.3.4 Side setting of the throat plate post
Thread tensioners and limiter ................................................................................................................................. 8
3.4.1 Description
3.4.2 Setting the tension of main and auxiliary tensioners
3.4.3 Setting the tensioning mechanisms of the main tensioners
3.4.4 Setting the adapting spring
3.4.5 Setting the thread limiter
Feeding mechanism of the needle feed and of the lower feed wheel ........................................................................ 10
3.5.1 Description
3.5.2 Stitch length mechanism
3.5.2.1 Setting the upper eccentric
3.5.2.2 Setting the prop
3.5.2.3 a Forward and rearward stitch length distribution (rough)
3.5.2.3 b Forward and rearward stitch length distribution (fine)
3.5.2.4 Setting of the control knob (including the stitch length limitation)
3.5.3 Lower feed wheel
3.5.3.1 Feeding clutches
3.5.3.1.1 Description
3.5.3.1.2 Setting the lever of the second step of feeding(angle, position)
3.5.3.1.3 Setting of the lower eccentric
3.5.3.1.4 Setting the engagement and disengagement of the clutches
3.5.3.2 Wheel feeder and its post
3.5.3.2.1 Height setting of the feeder and tensioning of the chain
3.5.3.2.2 Replacement of the feeder
3.5.4 Setting the top roller (pressing force, height)
Feeding mechanism of the top roller ....................................................................................................................15
3.6.1 Description
3.6.2 Side setting of the indented lower pulley
3.6.3 Side setting of the indented upper pulley
3.6.4 Setting the tensioning roller
3.6.5 Replacement of the indented belt
3.6.6 Top roller
3.6.6.1 Selection of the top roller diameter
3.6.6.2 Forward, rearward and side setting
3.6.6.3 Setting the gear clearance and in the mounting of the top roller
3.6.6.4 Replacement of the top roller
3.7
Setting the presser foot lift .................................................................................................................................... 19
3.8
Bobbin winder ....................................................................................................................................................... 20
3.8.1 Description
3.8.2 Setting the bobbin winder stop
3.8.3 Setting the friction gear
3.9
Safety clutch .......................................................................................................................................................... 21
3.9.1 Description
3.9.2 Setting the disengaging moment
3.10 Indented belt transmission ................................................................................................................................... 21
3.10.1 Setting the tensioning roller of the indented belt
3.10.2 Replacing the indented belt
3.11 V-belt, motor - head .............................................................................................................................................. 22
3.11.1 Tensioning
3.11.2 Replacing the V-Belt
3.12 Driving toothed belt ............................................................................................................................................................... 22
3.12.1 To exchange the driving toothed belt
3.13 Lubrication .............................................................................................................................................................................. 23
3.13.1 Description
3.13.2 Refilling oil
3.13.3 Multiple oil use
4. Thread trimming ................................................................................................................................................................................. 24
4.1 Description of the trimming mechanism
4.2 Setting the pickup roller
4.3 Setting the cam
4.4 Setting the fork
4.5 Setting the moving knife
4.6 Setting the fixed knife
4.7 Setting the retaining spring of the hook thread
4.8 Setting switching of the electromagnets
5. Lifting the top roller by electromagnet ........................................................................................................................... 26
5.1 Description
5.2 Setting the electromagnet pin
5.3 Setting the electromagnet current
5.4 Assembly of the top roller lifting electromagnet
6. Backtacking using electromagnet .................................................................................................................................... 27
6.1 Description
6.2 Electromagnet height setting
6.3 Setting the position of push-buttons
6.4 Change of the function of push-buttons
7. Connecting the electric elements on the machine head ................................................................................................ 28
8. Drive, control panel, position sensor
......................................................................................................................................... 28
9. Maintenance (table of operations) ............................................................................................................................................... 29
10. Setting the machine according to the sewing category ............................................................................................................ 29
10.1 Introduction
10.2 Table of setting the machine according to the sewing category
1. General safety instructions
The non-observance of the following safety instructions can cause bodily injuries or damages to the machine.
1. The machine must only be commissioned in full knowledge of the instruction book and operated by persons with appropriate
training.
2. Before putting into service also read the safety rules and instructions of the motor supplier.
3. The machine must be used only for the purpose intended. Use of the machine without the safety devices is not permitted.
Observe all the relevant safety regulations.
4. When gauge parts are exchanged (e.g. needle, top roller, needle plate, feed dog and bobbin) when treading, when the
workplace is left, and during service work, the machine must be disconnected from the mains by switching off the master
switch or disconnecting the mains plug.
5. Daily servicing work must be carried out only by appropriately trained persons.
6. Repairs, conversion and special maintenance work must only be carried out by technicians or persons with appropriate
training.
7. For service or repair work on pneumatic systems the machine must be disconnected from the compressed air supply system.
Exceptions to this are only adjustments and function checks made by appropriately trained technicians.
8. Work on the electrical equipment must be carried out only by electricians or appropriately trained persons.
9. Work on parts and systems under electric current is not permitted, except as specified in regulations DIN VDE 0105.
10. Conversions or changes to the machine must be authorized by us and made only in adherence to all safety regulations.
11. For repairs, only replacement parts approved by us must be used.
12. Commissioning of the sewing head is prohibited until such time as the entire sewing unit is found to comply with EC
directives.
It is absolutely necessary to respect the safety instructions marked by these signs.
Danger of bodily injuries !
Please note also the general safety instructions.
IMPORTANT WARNING
In spite of all safety measures made on the machines, inappropriate actions of the operator may lead to dangerous situations. In
industrial sewing machines, attention should be paid to the following still remaining possible sources of injury:
1. Moving sewing needle
- risk of injury when sewing with raised pressure foot or top roller, because the finger guard is then positioned too high,
- risk of injury when inadvertently threading down of the motor threadle.
2. Moving thread take-up lever
- risk of injury when inadvertently or intentionally inserting the finger(s) between the thread take-up lever and its guard.
3. Moving pressure member
- risk of injury when holding sewn work in immediate vicinity of the pressure member and beginning to insert under the
pressure member a considerably thicker sewn work portion,
- risk of injury when sinking the pressure member.
4. When switched off, the clutch motor slows down by inertia but would be reactivated by an accidental treading down of the
motor treadle. To avoid such risk, it is advised to hold the handwheel by hand and slightly to depress the motor treadle.
2. Introduction
This service book contains instruction for regulating the mechanisms of the sewing machine head.
The instructions for use and for putting the machine into operation and for the control of the stopmotor are not included in this
service book, but they are supplied as separate publications.
This service book is universal for all subclasses of the machine - it contains setting procedures for all elements which may be
placed on the machine of the given class. When the supplied subclass of this machine does not include some element, then it is
possible to leave out the respective parts of the instructions. The optional equipments of the machine and the respective
configurations of the subclasses of the machine are given in the operating instructions.
This sewing machine disposes of a large extent of its use. The machine should be set with respect to the parameters of the sewn
material, the sewing thread etc. The setting for the individual categories is given in the chapter 11.2.
For setting the machine, simple setting aids are used which are included in the accessory of the machine. Besides these aids,
universal measuring devices are used, such as slide calliper, feeler gauges and dynamometer for measuring the thread tension.
1
3. Head of the sewing machine
9
2
3.1 Hook and the hook post
3.1.1 Description
11
10
5
1
12
6
3
8
7
13
1
4
The hook (1) is mounted on the shaft (2) and is driven by the
gear (3) from the shaft (4).
The shaft of the hook (2) is slidably mounted on the top, in
post and, on the bottom, in a needle bearing.
The hook is provided with a lever (5) which is tilted when
removing the bobbin (6). The protecting sheet (7) protects
against the collision of the needle with the hook point. The
bobbin case opener (8) is driven by the eccentric (9) on the
shaft (2).
The oil tank (10) contains oil supply for the hook lubrication.
Superfluous oil is taken by the felt piece (11) used to lubricate
sliding mounting hook shafts. The wick connected to the felt
piece (11) lubricates the gearing (3).
The screws (12) serve for taking up the clearance of the gear.
The screws (13) fasten the post to the bedplate.
3.1.2 Height setting of the hook
The designated distance „A“ should be 5.3 mm.
Caution! Danger of injury!
Switch off the main switch ! Before starting the
setting operation, wait until the motor stops!
7
3
5
A
2
6
- Loosen both screws (1).
- By axial shifting of the bushing (2) set the axial clearance of
the wheel (3) to the least value still ensuring easy rotation
of the shaft (4) with the fixed wheel (3).
- Tighten both screws (1).
- Loosen both screws (5).
- Shift axially the shaft (4) with the hook (6) so as to obtain
the required distance “A”. For setting up use the setting
gauge (7) as per the repective figure.
- Carefully retighten the screws (5) after the adjustment.
Caution! One of these screws must bear on the flat of the
shaft (4).
4
3.1.3 Setting the distance of the hook from
the needle
The hook point (1) is set up to the maximum distance of
0.1 mm from the bottom of the needle recess (2). For the
sewing categories 1 and 2, the needle size 100 is set, for the
sewing categories 3 and 4, it is the needle size 160.
max. 0,1
2
Caution! Danger of injury!
Switch off the main switch ! Before starting the
setting operation, wait until the motor stops!
1
7
6
4
5
- Loosen only one screw (4).
- Loosen the screws (5) and tighten them only slightly.
- Shift the hook post (6) at the determined distance between
the needle and the hook point.
- Tighten carefully the screw (4) (be sure not to damage the
threads!)
- Tighten duly the screws (5).
- Check up the setting using a narrow strip of thin paper and
proceed to the eventual correction of setting.
4
Caution!
When changing substantially the sewing category, the protecting sheet of the hook (7) should
be set up.
5
2
2
1
3.1.4 Angular setting of the hook (timing)
The hook is to be angularly set in such a way that the hook
point (1) is opposite the needle at the moment, when the
needle shifts by 2.5 mm from its bottom dead center. This
corresponds to the 2O5° on the scale of the handwheel (3).
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
7
8
3
205o
4
5
- Remove the throat plate.
- Turn the handwheel (3) to the 2O5° and fix it with the screw
(4) which is component part ot the accessory of the machine
(tighten it carefully).
- Loosen the screws (5).
- Turn the hook into the required position.
- Pass the locating pin (7) contained in the machine accessories through the hole in the hook post bed (8) and insert
it into the groove of the gear wheel (6). In this way, the wheel
is axially set.
- Tighten to the maximum the screws (5) and take the locating
pin (7) out.
6
3.1.5 Protection of the needle and of the hook point
The protecting sheet (1) is to be set up in such a way that the
clearance between the protecting sheet and the needle (2) is
the least possible.
Caution ! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
2
5
3
- Remove the throat plate and the movable trimming knife.
- Unscrew the screw (3).
- Put the screwdriver into the hole of the screw (3) and, using
the regulating screw, set up the required clearance between
the needle (2) and the protecting sheet (1). When turning to
the right, the protecting sheet shifts out from the groowe
and inversely.
- Check up the protecting effect in pushing against the needle
in the sense of the arrow (5). The hook point must not catch
the needle. If so, set up the protecting effect, correct eventually the setting of the distance of the hook point from the
needle according to the paragraph 3.1.3.
- Screw in the screw (3).
1
1
3.1.6 Setting of the bobbin case opener
3
The bobbin case opener (1) is to be set in such a way that, at
the moment when the opener is in its dead centre, there would
be a clearance „A“ between the opener (1) and the projection
(2), whereas the finger (3) bears on the projection (4), „A“ =
0.7 mm for the sewing category 1 and 2, „A“ = 0.3 mm for the
sewing category 3 and 4.
4
1
Caution ! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
2
A
- On the handwheel (5), set the angle of 308° (the hook is in
its dead centre).
- Loosen the screw (6).
- Turn the eccentric (7) in such a way that the required
clearance between the elements (1) and (2) is attained.
- By turning the screw (10), set the height of the eccentric (7)
in such a way that it is in its highest position in retaining
the minimum clearance between the slide (8) and the fork
(9).
- Tighten duly the screw (6).
5
7
308o
8 9
10 6
3
3.1.7
Setting the regulation of the hook lubrication
Oil is wiped from the lubrication wick by the surface of the
hook eccentric and is then supplied by centrifugal force into
the hook path (7). The intensity of oil supply is regulated by
turning the screw (3).
Caution! Danger of injury!
Switch off the main switch ! Before starting the
setting operation, weit until the motor stops!
- To reduce the oil supply, turn the screw (3) to the right.
- To increase the oil supply, turn the screw (3) to the left.
- After the adjustment, loosen the screw (4) and set the height
of the oil tank so as to ensure reliable contact between the
surface of the eccentric and the lubrication wick.
3
4
Caution!
The quantity of the fed oil has been set up in the
manufacturing factory. This setting is to be done
only in emergency events. A bad setting of the quantity of the
fed oil or of the height of the lubrifying tube may cause a
rapid wear or a seizure of the hook.
1
3.1.8 Replacement of the hook
2
Caution! Danger of injury!
Switch off the main switch ! Before starting the
setting operation, weit until the motor stops!
3
- Remove the throat plate and the trimming knife together
with its holder.
- Unscrew the screws (1) and remove the splice (2).
- After having suitably turned a bit the hook, remove the
bobbin case (3).
- Unscrew thorougly the screw (4).
- Remove the body of the hook (5) upwards.
- When mounting, the procedure is inverse.
4
5
3.1.9
1
2
Setting the gear
The mutual angular orientation of the gear wheel (1) relative
to the gear wheel (2) should ensure the accessibility of the
screw (5) at the moment when the hook point comes to lie
opposite the needle (4). The wheel (2) is to be set with its gear
rim symmetrically to the centre of the gear wheel (1). The
clearance between the gear wheels is to be the least possible.
4
3
Caution ! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
5
6
205o
7
8 9
10
10
- Set the angle of 2O5° on the handwheel (6) and lock it with
the screw (7).
- On the removed post of the hook (8), according to the paragraph 3.1.10, the hook point (3) is to be turned a bit
according to the illustration.
- Turn the gear wheel (2) into the suitable position and insert
the post of the hook into the machine according to the
respective arrows. Check up, whether the screw (5) is accessible and, if not, repeat the procedure.
- Set the the distance of the hook from the needle according
to the paragraph 3.1.3.
- Set the precise angular displacement of the hook according
to the paragraph 3.1.4.
- Loosen the screw (10) and tighten them slightly.
- Set the clearence in the gear in turning the screws (9). Check
up, whether the gear has a clearance during the whole
revolution of the hook. Turn the handwheel step by step by
15° and, with each step, grasp the hook and try, if there is an
angular dead travel. Tighten carefully the screws (9).
- Tighten duly the screws (10) and try anew the clearance of
the gear.
4
5
1
6
3.1.10 Dismantling of the hook post
Caution ! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
- Loosen only one screw (5).
- Unscrew the screws (6).
- Shift the post(1) in the sense of the arrows and remove it
out from the machine.
- When mounting it, proceed inversely.
5
6
3
2
3.2
7
3.2.1 Description
The take-up lever (1) is mounted in ball bearings, both at the
spot of its suspending on the connecting rod (2) and in the
mounting on the loop (12). The take-up lever is of aluminum
and is provided with a stuck-in eye for two threads. The
connecting rod (2) is mounted on the eccentric pin (3), by
means of which the thread mechanism is adjusted according
to the category of stitching. The needle rod holder (4) is
mounted through the pivot (5) in a rotating way in the arm (6).
In its top part, the holder is guided by the guide pin (7). The
movement for the needle feed is given to it by the connecting
rod (8) driven by the feeding shaft (9). The connecting rod (8)
is mounted by pin (13) with needle bar holder (4).
The connecting rod (10) of the needle bar (11) on the loop
(12) is mounted in a ball bearing and it is slidingly mounted
on the needle bar carrier. The mechanism is lubricated by means
of a central-wick lubricating system.
13
1
8
12
9
10
11
4
6
5
Needle and thread mechanism
3.2.2 To check the handwheel angular adjustment
2
5
4
3
0o
6
1
The handwheel (5) must be situated in its precise position
relative to the needle and thread mechanism. This position is
given by a pin (2), which locks the connecting rod of the
needle rod (1) through a hole in the arm (3). In this position,
the indicator (6) of the handwheel must show „O“. The position
is fixed by the handwheel screw (4) contacting a small flat
surface provided on the upper shaft.
The correct adjustment of the angular position has been carried out at the producer‘s.
Caution ! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
3.2.3 Height setting of the needle bar
At the moment, when the hook point passes around the needle,
the upper edge of the needle eye must be about 1 mm below
the hook point. In an opposite case, it is necessary to set the
height of the needle bar as follows:
Caution ! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
1
- Remove the front guard.
- Loosen the screw (1) of the needle bar carrier
- Set the correct height of the needle bar and tighten anew
the screw (1).
Caution !
An incorrect setting of the needle bar height may
cause the striking of the hook point against the
needle.
1
5
3.2.4 Angular setting the pin of the thread
mechanism
45o
The hinged pin (2) of the connecting rod (3) can be set in two
positions:
- for stitching category 100, 200, 300 - the groove of the pin
(2) is in position (turned) as shown in Fig. “A”
- for stitching category 400 - the groove of the pin (2) is in
position (turned) as shown in Fig. “B”.
Set the connecting rod pin as follows:
A
1
2
3
45o
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
B
- Remove the front guard.
- Loosen the screw (1) /imbus/ of the connecting rod (3) pin
(2).
- Set the pin into the corresponding position and tighten
anew the screw.
- The correct position is given by the flat on the pin (2), on
which the screw (1) is tightened.
- After having tightened the screw (1) check the axial
clearance of the connecting rod (3).
44 stupnì
1
2
3
4
3
3.2.5
Side setting of the needle bar holder
The correct position of this holder is in such case, when the
needle bar is lined up with the presser-foot bar. The needle bar
holder can be set as follows:
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
A
- Loosen the screw (1) of the pin (2).
- Loosen the screw (3) of the guide pin (4).
- In shifting the pin (2) set the needle bar holder on the
measure „A“ = 8 mm (distance between the front face of the
arm and the front face of the safety bolt (5) of the needle
bar holder) /at the same time the pin (4) shifts/.
- The guide pin (4) is to be set in such a way that the needle
bar holder moves easily.
- Tighten the screws (1 and 3).
1
2
5
3
1
244o
2
3.2.6 Setting the needle (the needle bar holder)
in the direction of sewing
When shifting out the needle from the throat plate insert,
at the moment, when the needle eye is at the level of the top
surface of the throat plate insert, the distance between
the needle and the wall of the throat plate insert must be „A“ =
0.2 mm.
Caution ! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
A
5
4
6
- Shift the insert (3) up to the stop in the sense of the arrow.
- Set the maximum allowed stitch length.
- Set the handwheel (1) to the angle of 244° and lock it with
the screw (2).
- Loosen the screw (4) of the lever (5).
- By turning the needle bar holder (6) on the pin (7) set the
required distance “A” = 0,2 mm.
- Tighten up the screw (4) and check up the setting.
Caution!
A faulty setting may cause bending or breaking of
needles against the throat plate insert.
7
6
3.3 Throat plate and its post
3.3.1 Description
The throat plate(1)is universal for all categories of sewing.In
the throat plate there is mounted an exchangeable insert (2).
The machine is supplied with several types of inserts differing
in the width of their needle aperture (3), see tab. in the par.11.2.
For ensuring a good function of the thread trimming device,
the insert can be set in various positions in the sense of arrows
in such a way that the rear edge of the hole in the throat plate
(4) prevents unthreading the thread from the sewn material
when forming the first stitches at the beginning of the seam.
1
2
3
2
4 2 3
4
3.3.2 Mounting and removing the throat plate
and its insert
6
891
When mounting the throat plate (1), the finger (2) must engage
into the recess (3). To remove the throat plate insert (4), screw
out the screw (5), take out the washer (7), loosen the screw
(8) and remove the insert (4) by oblique upward movement.
7
5
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
6
-
Turn the finger (2) in the sense towards the throat plate (1).
Mount the throat plate (1).
Screw in the screws (6).
Slide in the insert under the washer (9)in the oblique
rearward sense (4).
- Mount the insert (7) and screw in the screw (5).
- Tighten the screw (8).
- When removing the insert, proceed in an inverse sequence.
1
3
A
2
3.3.3 Setting the throat plate and its insert
3
The insert of the throat plate should be set in the machines
with the trimming device in such a way that the edge (1) is at
the distance „A“ = 1 to 2 mm before the spot of interlacing of
the threads (2). For the stitches up to the length of 2/3 of the
maximum length, the insert is to be set in its extreme front
position in the sense of the arrow. For long stitches, it should
be in its extreme rear position, against the sense of the arrow.
With the machines without the trimming device, the insert is
in its extreme rear position.
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
- Loosen the screws (3).
- By applying a heavy pressure of the screwdriver, shift the
insert in its required position.
- Tighten the screws (3).
3.3.4 Side setting of the throat plate post
3
The post of the throat plate (1) is to be side set in such a way
that the axis of the hole in the insert of the throat plate (2) is at
the distance „A“ = 0.1 mm to the right from the axis of the
needle (3).
4
A
1
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
2
5
- Loosen the screws (4 and 5) (from the rear side of the post
as well).
- Shift the post (1) in the sense required for attaining the
distance „A“ = 0.1 mm.
- Tighten the screws (4 and 5) and check up for the correct
setting.
7
3
4
5
10
6
8
2
A
13
7
12
1
14
3
2
1
0,1
4
1
3
2
5
3.4
Thread tensioners and limiter
3.4.1 Description
The main tensioners (1) serves for creating the tension of the
thread when tightening the stitch. The auxiliary tensioner (2)
reduces the risk of pulling out of the thread after the thread
trimming when removing the sewn material, when the thread
is passed through this material and when the main tensioner
is relieved. The main tensioner is relieved by the mechanism
controlled by the shaft of the presser bar lifting (3) holding
the lever (4) with a pulley. The motion is then transmitted by
the lever (5) and the tie rod (6) on the thread tensioner plate
(7) whose displacement (motion) relieves the thread tensioner
springs (8). In machines provided with a thread trimming
device, the main tensioners (1) are relieved as well upon the
switching on of the electromagnet (10) whose electromagnetic
field will attract the thread tensioner plate (7). The mechanism
of the adapting spring (12) maintains the upper thread in its
tensioned state when passing through the hook and when
entering the needle into the sewn material. The thread limiter
(13) limits the length of the thread fed by the take-up lever
when moving from the upper to the bottom dead centre to get
a controlled passing of the thread through the hook. The
auxiliary guide (14) maintains the upper thread in front of the
needle in a tensioned condition and helps against pulling the
thread from the needle after thread trimming.
3.4.2 Setting the tension of the main and auxiliary
tensioners
The tension of the main thread tensioners is regulated by
means of the nuts (1). The force of tensioning the thread is
measured by the dynamometer (2) as it is shown on the
illustration. The size of this force differs according to the
category, and its orientation value is indicated in the par. 11.2.
The tension of the auxiliary tensioner is regulated using the
nut (3). It should be the least possible, but sufficient for
unthreading the thread from the sewn material when removing
the sewn material from the pressing element without leaving
the tensioner.
3.4.3 Setting the tensioning mechanisms
of the main tensioners
7
In the rest position of the tensioners, when pushing the plate
of the tensioners on the spot “A” 3.4.1, this plate must have
the socalled dead travel of about 0,5 mm. At this lifting, the
tension discs of the tensioners must not be relieved. This can
be attained by a suitable shaping of the relieving disc of the
tensioners - this has been set up in the manufacturing factory.
In the maximum opened position of the tensioners, the plate
of the tensioners, when pushing it at the spot “A” 3.4.1, must
still have the minimum lifting. This can be attained when axially
shifting the lever (3) with the roller (5) on the shaft (4).
The disengagement of the main tensioners must be
coordinated with the top roller lift. To achieve this, turn the
lever (3) with the roller (5) on the shaft (4). The movement of
the roller (5) on the slanting surface (6) of the lever (7)
disengages the tensioners. In this way, also a lag of the upper
thread tension disengagement after the top roller lift can be
obtained.
Caution ! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
9
6
8
- Remove the rear cover with the top roller lift magnet.
- Loosen the screws (1) and (2) of the lever (3).
8
- In the rest state of the machine (with not relieved tensioner
discs) set the lever (3) in turning it slightly on the shaft (4)
to a position in which the roller (5) of the lever (3) is in
contact with the slanting surface (6) of the lever (7) and is
about 0.1 mm distant from the flat surface (8) of the lever.
- At the maximum lift of the top roller, the roller (5) moves on
the flat surface (9) of the lever (7); in this condition, there
must be a minimal play at the tensioner plate lift (when
pushing qat the spot “A” (3.4.1), the plate must still have a
minimum lifting - between the roller (5) and the surface (9)
there is a minimum clearance). Retighten the screws (1) and
(2), check the play, and correct it in case of need.
3.4.4 Setting the adapting spring
The mechanism of the adapting spring is in the machine arm
set by the pin (1) and fixed by the screw (2). The axial
adjustment shall ensure that the surfaces of the parts (3) and
(4) are aligned (the threaded thread must in no place break on
edges). The initial position of the adapting spring (5) shall
ensure that “B” = 1 to 1.5 mm (see the Figure).
3
8
4
1
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
6
7
- Loosen the screw (2) and take the mechanism out of the
machine arm.
- Turning the body (6) relative to the pin (1), set the required
initial position of the adapting spring /the screw (7) has
been set at the producer´s so as to permit the turning
movement of the body (6) the screw must not be fully
tightened/.
- During the installation of the mechanism into the machine
arm take care of the axial adjustment of the mechanism.
- Retighten the screw (2) and check the adjustment.
- Loosen the nut (8) of the mechanism, insert a screwdriver
into the notch of the screw (9) and set the required value of
the adapting spring. By turning the screw clockwise you
increase the spring force, and vice versa.
- Retighten the nut (8) and check the function of the adapting
spring.
9
2
8
3
A
5
4
9
3.4.5 Setting the thread limiter
The thread limiter is to be set in such a way that, when sewing
and passing the thread through the most distant point of the
hook, the spring (2) shifts by about 1/4 to 1/2 length of its
total length. This means that the thicker will be the sewn
material and the longer will be the stitch length, the more will
be the limiter shifted in the sense of the arrow and inversely.
Under standard sewing conditions, the thread limiter is set in
its tested positions depending on the sewing category in
accordance with the chapter 11.
3
1
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
2
- Tighten the screw (3).
- Set the thread limiter (1) so as to ensure a minimum motion
of the adapting spring (2) when the thread passes around
the bottom of the hook.
- Tighten the screw (3).
9
3
1
3.5 Feeding mechanism of the needle feed
and of the lower feed wheel
2
3.5.1 Description
The feeding mechanism is formed by the leverage (1) which is driven
from the main shaft through the eccentric with connection rod (2). The
feeding motion is transmitted by the shaft (3) on the clutch of the
bottom feed (7).
The engaging and the disengaging function of the clutch (7) is controlled
from the lower shaft (8) through the eccentric with the connecting rod
(9) and through the wedge coupling (10).
The feeding movement is transmitted by the shaft (11) through the
chain transmission (12) onto the wheel feeder (13).
The stitch length is set by the knob (14) through the leverage (15) to
the feeding mechanism (1).
14
4
15
5
6
8
9
13
12
7
11
3.5.2 Stitch length mechanism
3.5.2.1 Setting the upper eccentric
10
1
10
The eccentric (1) must be set in its angular position in such a way that
the horizontal component of the needle motion is in a phase delay from
the vertical component of this movement. This refers to the angle of
90° on the handwheel (2), when the setting stick (3) is engaged into
the eccentric (1) and leans from above against the feeding shaft (4).
3
Caution! Danger of injury!
Switch off the main switch! Before starting the setting
operation, wait until the motor stops!
2
- Set the angle 90° on the handwheel (2) and fix it with the screw (5)
which is component part of the accessory of the machine (tighten it
with care).
- Loosen the gripping joints of the levers (6) and (7).
- Turn the feeding shaft (4) in such a way, so that the recesses (flats)
point towards the bedplate (owing to the unambi-guous setting of
the eccentric by means of the setting bar).
- Insert the setting bar (3) into the hole in the eccentric (1) and prop
it from above against the feeding shaft (4).
- Shift axially the eccentric (1) on the shaft into its extreme positions
and place it in the middle.
- Tighten the screws of the eccentric (1) to the maximum (one screw
first and, after having turned slightly the hand-wheel, the second
screw as well).
- Turn the feeding shaft (4) back into the position for setting the
leverage in such a way, so that the levers (10) of the mechanism pass
in the spots of the recesses.
- Tighten the gripping joints of the levers (6) and (7).
- Test the sufficient clearance in the recesses of the feeding shaft (4)
and, using the levers (10) with the maximum stitch length forward
and rearward – push against the reverse stitching lever.
- Correct eventually the position of the feeding shaft.
90
o
5
7
4
6
D
C
1
B
A
3.5.2.2 Setting the prop
In this machine with a wheel feed, the prop (1) is mounted in the pits
(A and C) as per the drawing.
3
2
9
1
6 7 8
3.5.2.3a Forward and rearward stitch length
distribution (rough)
The cam (1) is to be set at the respective angle in such a way that the
stirrup (6) is oriented in such a position, so that the connecting rods (7
and 8) are in a line with a thoroughly screwed in knob (9) and with
turning the handwheel at 0°. This setting can be done only after having
set the top eccentric according to the paragraph 3.5.2.1.
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
0o
4
- Set the zero stitch /screw in the knob (9) to the bottom of the cam
(1)/.
- Set the angle 0° on the handwheel and lock it with the screw (4).
- Turn the screw (3) in the respective sense in such a way that the
connecting rods (7 and 8) are in a line and tighten the screw (2).
10
3.5.2.3b Forward and rearward stitch length
distribution (fine)
When setting the maximum length of the stitch, the forward
and the rearward stitch length must be equal with the
maximum error of ± 5 %. This setting can be done only after
having set the needle bar holder in the direction of sewing
(par. 3.2.6) and the wheel feed (par. 3.5.3.1.2).
3
Caution! Danger of injury!
switch off the main switch! Before starting the
setting operation, wait until the motor stops!
2
- Set the maximum stitch length .
- Place a suitable material under the presser foot and mark
therein the forward and the rearward stitch length.
- With an unequal length of the stitch, proceed to the
correction
of setting by turning the screws (2 and 3). When tightening
the screw (3), the forward length of the stitch is shortened
and inversely. When tightening the screw (2), the forward
stitch length is lenghtened.
- Each time first loosen one screw and then retighten the
other one.
3.5.2.4 Setting the control knob
(including the stitch length limitation)
The control knob (1) is to be set up in such a way that, when
turning it in counterclockwise sense up to the stop, the
maximum stitch length valid for the given sewing category is
attained (cat. 1: 3 mm, cat 2: 5 mm, cat. 3 and 4: 7 mm). The
scale of the control knob is to be oriented in such a position,
so that the scale end corresponds to the maximum stitch
length, excepting the first sewing category, where the stitch
length of the indicator is 3 mm.
1
2
3
4
Caution! Danger of injury
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
5
2
8
1
5
7
6
11
- Screw in the screw of the control knob in such a way, that
the spherical surface of the screw (3) bears on the seat of
the cam (4).
- Loosen the screw (5) and turn the control knob in the
clockwise direction, until the pin (6) of the knob (1) bears
on the pin (7). Tighten firmly the screws (5).
- Turn the knob in the counterclockwise direction up to the
stop, when the pin (6) of the knob (1) bears on the pin (7).
- In a sewing test check up the length of the stitch, if this
corresponds to the maximum stitch length valid for the given
sewing category.
- If the stitch is longer, loosen then the screws (5) and turn
the knob in the clockwise direction and inversely. Tighten
firmly the screws (5).
- Insert a screwdriver into the hole (8) of the scale (2) and
adjust the scale in such a way that the maximum length on
the scale is against the marking of the stitch length on the
machine arm.
- For the sewing category 1, set the control knob (1) on the
stitch length of 3 mm and check it by a sewing test.
- Loosen the screws (5) and turn the control knob (1) in the
counterclockwise direction, until the pin (6) of the knob (1)
bears on the pin (7). Tighten firmly the screws (5).
- Put a screwdriver into the hole (8) of the scale (2) and adjust
the scale in such a way that the value of the stitch length on
the scale against the marking on the arm is 3 mm.
2
3
8
9
10
1
13
7
11
5
6
12
4
3.5.3 Lower feed wheel
3.5.3.1 Feeding clutches
3.5.3.1.1 Description
The feeding clutch is formed by the clutch cover (1) driven
from the connecting bar (2), by the clutch star (4) driven from
the connecting rod (3) and by the carrier plate (5) firmly
connected with the shaft (6). Of the clutch give the connecting
rods (2 and 3) an opposite direction swinging movement. The
clutch is coupled by means of the wedge (7) on the connecting
rod (8) through the eccentric (9) which is placed on the lower
shaft (10).
In the position, when the wedge is disengaged, the star (4)
is shifted out from the frictioning engagement with the lining
of the carrier plate (5) by means of the spring washer (11). The
plate (5) lining is then pushed by means of a flat profiled
spring (12) against the cover of the clutch (1).
In the position, when the wedge is disengaged, the star (4)
is pushed against the plate (5) lining and, at the same time,
the friction connection with the cover of the clutch (1) is
disconnected. Within a short instant, when engaging and
disengaging with the carrier plate (5), there are in a friction
engagement both the cover (1) and also the star (4), namely in
the dead centre of the connecting rods (2 and 3). The setting
of the change-over of clutches is done by tightening or by
loosening the nut (13).
3.5.3.1.2 Setting the lever of the second step of
feeding (angle, position)
The lever of the second step (1) must be set in such a way
that, in the bottom dead centre of the needle, the axis of the
spider part (2) lies in the screw axis (3). The pin screw (4) can
be mounted into the position (4.1 - corresponds to the
maximum stitch length of 5 mm) or into the position (4.2 corresponds to the stitch length of 7 mm). The position of the
pin screw is given by the sewing category (see par. 11.2).
1
4
4.2
4.1
6
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
8
5
2
Lever (1) displacement.
- Loosen the screw (6).
- Set the maximum stitch length.
- Set the angle 180° on the handwheel.
- Unscrew the screw (5) and put the needle shank in its hole.
- Turn the lever (1) until the needle drops into the clutch disk (2).
- Side set the lever (1) to the measure „A“= 0.5 to 1 mm.
- Tighten the screw (6).
- Screw in the screw (5) and seal it with the Loctite cement.
Change of the position of the pin screw (4).
- Remove the retaining ring (7).
- Unscrew the screw (4) and screw it into the new position
and tighten it duly. Mount the connecting rod (8) and the
retaining ring (7).
A
5
3
2
7 8
1 4
12
5
1
4
3.5.3.1.3 Setting of the lower eccentric
The rotation of the eccentric (3) must be delayed in phase by
1/4 revolution against the rotation of the eccentric of the stitch
length. This corresponds to the angle of 244° on the handwheel
(1), when the setting pin (4) is put into the eccentric (3) which
is in contact with the indented belt (5).
244o
2
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
- Set 244° on the handwheel (1) and lock it with the screw
(2), which is included in the accessory of the machine
(tighten it carefully).
- Put the setting stick (4) into the hole in the eccentric (3) and
prop it from below against the indented belt (5).
- Set eccentric (3) axially.
- Tighten it the utmost the screws of the eccentric (6).
- By means of the handwheel, turn the eccentric (3) into the
marked position and check in this position the clearance
„A“ = 0.05, proceed eventually to its correction by a new
side setting of the eccentric.
6
3
A
1
3.5.3.1.4 Setting the engagement and
disengagement of the clutches
90o
The nut (7) is to be side set in such a way that the shifting of
the clutches is done at the moment when the clutch disks (3)
do not move, which means, when they are at the dead center
of their oscillating movement. This corresponds to the angle
90° on the handwheel.
2
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
7
6
9
- Loosen the screws of the indented pulley of feeding and
shift it to the left.
- Set the maximum stitch length.
- Set the angle 90° on the handwheel (1) and lock it with the
screw (2). which is included in the accessory of the machine
(tighten it carefully).
- Loosen three screws (6) in the nut (7) and unscrew it by
2 mm to the left.
- Tighten slowly the nut (7), until it strikes against the axial
bearing (9). (At this moment, the tightening moment
increases in jumps) and tighten the screws (6).
- Set the the handwheel on 85° and push the backtacking
lever, the feeder is to turn against the movement of the
needle. Set then the handwheel on 95°, the feeder is to be
turned in the sense of the needle movement. If not being
so, correct the side setting of the nut (7). When the clutches
shift too soon, turn a bit the nut (7) to the right and inversely.
- Tighten the screws (6).
- Return the indented pulley in its original place according to
the paragraph 3.6.2.
3
13
3.5.4.2 Wheel feeder and its post
3.5.4.2.1 Height setting of the feeder and tensioning of the chain
The wheel feeder (1) is to be set in such a way that the points
of its teeth overtop the insert of the throat plate by „X“= 0.3 to
0.7 mm. When sewing soft and thick materials, it is necessary
to increase the value „X“, until a good quality of feeding is
attained, but only to the measure of not deteriorating the
beginning of sewing after the carried out thread trimming.
Set the height of the feed dog using a setting gauge.
With every correction of the teeth height, the tension of the
chain (2) is to be corrected.
:
"
Caution! Dangere of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
#
!
- Loosen the screw (3).
- Loosen the screw (4).
- Loosen or tighten the screw (5) and push simultaneously
with finger the feeder (1) downwards, until the required
height of the teeth „X“ of the wheel feeder is attained.
- Tighten then still the screw (5) by 45° (1/8 revolution).
- Tension the tensioner (6) up to the stop. Be careful in side
shifting it to the centre of the chain. Tighten the screw (3).
- Loosen the screw (5) by 45° (1/8 revolution), into its original
position. In this way, the optimal clearance of the chain
transmission is attained.
- Tighten the screw (4).
- Correct the set height of the top roller according to the
par. 3.5.4.
$
14
3.5.3.2.2
Replacement of the feeder
For the replacement of the wheel feeder (change of the wheel
feeder according to the machine setting - see par. 11.2 - setting
of the machine - feeder - pitch of the teeth).
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
!
"
#
&
$
'
%
- Unscrew the screws (1) and remove the throat plate (2).
- Unscrew the guard (7).
- In pulling upwards (securing by a spring), pull out the feeder
(3) with the guide (4).
- Replace the feeder (3).
- Insert the feeder with the guide into the groove of the holder
(5).
- Mount the throat plate (2) and tighten up the screws (1).
- Check up, if the spring (6) pushes the guide (4) with the
feeder (3) against the wheel (8).
- In the opposite case, loosen the screws (9), tense up the
spring (6) in such a way,so that the guide (4) with the feeder
(3) is pushed against the wheel (8) and tighten the screws
(9).
- Mount the guard (7) and tighten the screws.
3.5.4 Setting the top roller (pressing force, height)
When lowering the top roller (1), set the clearance „A“ between
the feeder (5) and the top roller to the maximum of 0.2 mm.
Set the pressing force of the top roller (1) so as to avoid the
slippage of the sewn material when feeding it.
Method of setting the height of the top roller:
- Lower by hand the presser bar (3) with the top roller (1)
above the wheel feeder (5).
- Loosen the screw (4) and set the required value „A“ (0.2
mm).
- Tighten the screw (4).
Setting the force of the top roller (1).
- In screwing in the screw (2),the force of the top roller is
increased and inversely.
"
!
)
#
" ! &
$
3.6
Feeding mechanism of the top roller
3.6.1 Description
%
#
'
$
#
#
"
The starting movement for the drive of the top roller feeder is
the bottom feeding shaft. From this shaft, the movement is
transmitted by the indented belt (1) onto the top feeding shaft
(2). A component part of the transmission by indented belt is
the pulley (3), the tensioning roller (4), the roller (5) and the
pulley (6). Starting from the shaft (2), the movement is further
transmitted through the wheels (7 and 8) ontothe articulated
shaft (9). From this articulated shaft, the movement is
transmitted by a cone transmission, situated in the holder
(10), onto the feeder wheel (11). The shaft of the wheel (8) is
mounted in the screw (12) on bearings. The articulated shaft
(9) contains two joints (15) and a telescopic part (16). Both
these elements secure the lifting and the tilting of the top
roller.
!
15
3.2.4 Angular setting the pin of the thread
mechanism
45o
The hinged pin (2) of the connecting rod (3) can be set in two
positions:
- for stitching category 100, 200, 300 - the groove of the pin
(2) is in position (turned) as shown in Fig. “A”
- for stitching category 400 - the groove of the pin (2) is in
position (turned) as shown in Fig. “B”.
Set the connecting rod pin as follows:
A
1
2
3
45o
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
B
- Remove the front guard.
- Loosen the screw (1) /imbus/ of the connecting rod (3) pin
(2).
- Set the pin into the corresponding position and tighten
anew the screw.
- The correct position is given by the flat on the pin (2), on
which the screw (1) is tightened.
- After having tightened the screw (1) check the axial
clearance of the connecting rod (3).
44 stupnì
1
2
3
4
3
3.2.5
Side setting of the needle bar holder
The correct position of this holder is in such case, when the
needle bar is lined up with the presser-foot bar. The needle bar
holder can be set as follows:
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
A
- Loosen the screw (1) of the pin (2).
- Loosen the screw (3) of the guide pin (4).
- In shifting the pin (2) set the needle bar holder on the
measure „A“ = 8 mm (distance between the front face of the
arm and the front face of the safety bolt (5) of the needle
bar holder) /at the same time the pin (4) shifts/.
- The guide pin (4) is to be set in such a way that the needle
bar holder moves easily.
- Tighten the screws (1 and 3).
1
2
5
3
1
244o
2
3.2.6 Setting the needle (the needle bar holder)
in the direction of sewing
When shifting out the needle from the throat plate insert,
at the moment, when the needle eye is at the level of the top
surface of the throat plate insert, the distance between
the needle and the wall of the throat plate insert must be „A“ =
0.2 mm.
Caution ! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
A
5
4
6
- Shift the insert (3) up to the stop in the sense of the arrow.
- Set the maximum allowed stitch length.
- Set the handwheel (1) to the angle of 244° and lock it with
the screw (2).
- Loosen the screw (4) of the lever (5).
- By turning the needle bar holder (6) on the pin (7) set the
required distance “A” = 0,2 mm.
- Tighten up the screw (4) and check up the setting.
Caution!
A faulty setting may cause bending or breaking of
needles against the throat plate insert.
7
6
12
10 11
1
8 9 2
3
4
3.6.5 Replacement the indented belt
Before replacing the indented belt, the bottom feeding shaft
is to be removed. The procedure is as follows:
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
5 6
7
21
15
14
19
16
18
20
23
17
22
24
13
25
17
- Loosen the screw (1) of the tensioning roller (2) and loosen
it.
- Loosen the screws (3) of the pulley (4) and shift it to the left
in such a way that the screws (5 and 6) of the feeding clutch
(7) are accessible.
- Loosen the screws (5 and 6).
- Loosen the screws (8) of the axial ring (9).
- Loosen the screws (10) of the chain wheel (11).
- Push the shaft (12) to the left in such a way that it is out of
the pulley (4).
- Remove the pulley (4).
- Remove the front guard.
- Loosen and unscrew the screw (14) of the holder of the
wheel (15) and remove it from the holder (21).
- Loosen the screws (16 and 17) of the holder (18).
- Remove the holder (18) together with the holder (15) and
articulated shaft (13) from the machine.
- Loosen the screws (19) of the pulley (20).
- Loosen the screw (24) of the ring (25).
- Hold the pulley (20) and pull out the feeding shaft (22) from
the arm in such a way that it is possible to remove the
indented belt (23) from the arm of the machine.
- Replace the belt with a new one and proceed to the assembly
(inverted procedure of dismantling).
- Proceed to the setting operation according to the par. 3.6.2,
3.6.3 and 3.6.4.
3.6.6 Top roller
3.6.6.1 Selection of the top roller diameter
The machine can be supplied with two types of top roller,
namely with the diameter of 25 mm and with the diameter of
35 mm. The suitability of the diameter used depends on the
type of sewing and on the concrete technological operation.
There are in general valid the following principles for the
selection of the wheel diameter:
ø 25 mm - for sewing small radii
ø 35 mm - for sewing straight sections or big radii
- for sewing with great passages to thicker materials
3.6.6.2 Forward, rearward and side setting
Fig. 1
Fig. 2
4
2
1
The top roller must be in a defined position in relation to the
needle:
a) view (see Fig. 1) - the value „X“ depends on the diameter of
use top roller (ø 25 - 6.5 mm; ø 35 - 10.5 mm), it is measured
from the the needle bar up to the roller edge when turning
the handwheel to the 180° of the scale against the indicator
b)view (see Fig. 2) - the wheel edge must fit with the edge of
the needle operture at the spot of the needle punch.
These values are to be set as follows:
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
3
- Loosen the screw (1).
- By shifting the holder (2) with the top roller (3) in the groove
of the holder (4) set the required value „X“ and tighten the
screw(1).
- Loosen the screw (5)
- By shifting the holder (2) in the holder (6) set the bottom
edge of the roller to the edge of the needle operture.
- Tighten the screw (5).
5
6
X
3.6.6.3 Setting the gear clearance
and in the mounting of the top roller
In the cone gear of the drive of the top roller foot, the minimum
clearance must be set. A too small clearance will increase the
friction resistance of the gear, the excessive clearance will
influence the inaccuracy of feeding. The top roller itself is
mounted on balls. With this type of mounting,it is also
necessary to set the minimal possible radial clearance.
The given clearances are set as follows:
7
6
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
3
2
4
5
1
Clearance in the wheel mounting
- Loosen three screws (5) /only slightly/.
- Using the screw (4) set the minimum clearance in the top
roller mounting (2) /it must easily rotate without any rubbing
and with a minimum clearance/.
- Tighten the screws (5), check the set up clearance, eventually, repeat the setting procedure.
Clearance in the conic gear
- Loosen the screw (1), in shifting the wheel, resp. the holder
(3) in the holder groove (6), set the minimum clearance,
the pinion (7) must be pushed up to the holder bottom (6).
- Tighten the screw (1), check the set up clearance.
18
3.6.6.4 Replacement of the top roller
6
When replacing the top roller, proceed as follows:
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
1
- Unscrew the screw (1).
- Unscrew the screw (3) with the washer (2).
- Remove the driven top roller with the holder (4) from the
holder (5) and from the articulated shaft (6).
- Mount another top roller in inverted procedure to
dismantling.
- Set the top roller according to the par. 3.6.6.2.
5
2
4
3
3.7 Setting the presser foot lift
2
5 3
The maximum lift of the presser foot when lifting the foot with
knee lever or with electromagnet is to be „A“ = 12.5 mm.
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
4
1
- Place a cube (1) having the height of „A“ = 12.5 ± 0.7 mm
under the presser foot.
- Screw in thoroughly downwards the screw (2).
- Tighten slightly the screw (3) in such a way that the lever
(4) turns on the shaft (5) with a certain friction moment.
- Push with the screwdriver on the lever (4), until it attains
the wall inside the arm of the sewing machine.
- Return the lever (4) back by about 1 mm and tighten the
screw (3). With the maximum top roller lifting, the lever will
not strike into the machine arm.
- Check the axial clearance of the shaft (5) which should be
the least possible.
- Using the screw (4) set the normal pressure force of the
presser foot.
A
19
3.8
4
Bobbin winder
3.8.1 Description
The winder (bobbin winder) winds a reserve of the hook thread.
It is driven by a spring-mounted friction gear, which stops
after having filled the bobbin.
An ideal winding is attained with a sufficient pretension of the
thread obtained on the thread guide (4) and with 1 mm under
the diameter of the bobbin. The shaft is mounted in a swinging
way and the friction gear is put into engagement by means of
a pickup lever (1) and a cam. The winder is fixed on the machine
arm by two screws (3). The thread is passed through according
to the illustration, the thread is cut off after having stopped
the winding operation using the cutting device (5).
5
3
3
1
3.8.2 Setting the bobbin winder stop
The moment of interrupting the winding is determined by the
mutual position of the pickup lever (1) and the cam (5) on a
common shaft.
The cam is locked in its functional position by the screw (6).
The mutual position is to be set on a not incorporated winder
in such a way that in the moment, when the pickup lever leaves
the space of the bobbin, the pressing function of the cam on
the winders shaft is interrupted and it moves in the sense of
the arrow. A fine setting is to be done on an incorporated
condition in the machine. Using the screw (2), the position of
the friction part of the pickup lever (1) is adapted. In opening
the lever, the stopping function is accelerated. Its inverse
function delays it. A test is to be done after having inserted
the bobbin, when passing the thread through the device and
when winding at the running of the machine.
6
5
2
1
3.8.3 Setting the friction gear
7
8
The friction gear is formed frontally by the disk (8) on the
main top shaft of the machine and by the disk (7) with a rubber
ring on the shaft of the winder.
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
9
A
B
- Proceed to the setting operation with a removed rear guard.
- The winder is in its stopped position.
- Loosen two screws (9) in the disk (8) through the hole in
the arm.
- By shifting axially the disk in the sense A, B, set the disks of
the winder (7) at the distance of 0.5 mm from the rubber
ring.
- Tighten the screws (9) in the disk (8).
- Put the winder in its working position and proceed to a
winding test.
- Mount the rear guard.
20
2
3
1
3.9 Safety clutch
4
3.9.1 Description
5
The machine is provided with a safety clutch which enables
the turning through of the lower belt wheel (1) on the hub of
the lower shaft (2), when the hook is blocked. This blocking
occurs due to the penetration of thread into the hook path.
With current running, this clutch should not disengage during
the normal running. The mutual coupling of the belt wheel (1)
and the hub (2) is effected by means of the bills (3) which are
firmly connected with the belt wheel (1). The bills fit in the
conic holes of the hub (2) and are pushed therein by means of
the springs (4).
Putting the clutch in its working position, eventual checking
its correct position are to be done in blocking the hook using
a screwdriver and in turning a bit the handwheel.
3.9.2 Setting the disengaging moment
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
The correct value of the tensioning moment (8 Nm) has been
set up by the manufacturer. when this value is lower, in a
current running, the clutch may disengage. In an opposite
case (the moment is higher), the clutch will not disengage. In
both cases it is necessary to proceed to a correction of the
moment. In turning the nut (5) to the right, the moment will
increase and on the contrary. The value of the tensioning
moment is very sensible to the turning of the nut (5). When
setting it, it is necessary to proceed very carefully, set it up
only in emergency cases! Check the moment using a torquelimiting wrench.
Caution!
The clutch guarantees only one mutual position
of the hub of the lower shaft (2) and that of the
belt wheel (1). No checking according to the gauge
marks is needed. Putting the clutch out of operation by
excessive tightening of the nut (5) can cause, when blocking
the hook, the destruction of the gear within the drive of the
hook.
3.10
Indented belt transmission
3.10.1 Setting the tensioning roller of the
indented belt
4
The optimum tension of the indented belt (1) is attained in
setting the tensioning roller (2) in such position, when the
roller applies the pressure of F = 20 N against the belt. The
roller must be side set in such a way that the edge of the
indented belt does not overlap over the edge of the roller.
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
- Remove the handwheel and the belt guard, remove the Vbelt.
- Unlock the fastening of the loop, on which the roller (2)
is mounted in such a way that the loop turns freely.
- Lift the roller (2) upwards and, thereafter, using the dynamometer (4), pull horizontally the roller in applying the force of
2O N. In this position, tighten the fastening screw (3).
- Check the side shifting of the roller.
2
3
1
21
4
3
2
3.10.2 Replacing the indented belt
To observe: in machines with Mini-stop first remove the driving
toothed belt as instructed in par. 3.12.
When replacing the indented belt, the mutual position of the
pulleys (4 and 5) should be maintained.
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
1
- Remove the handwheel, the belt guard and the V-belt.
- Remove the retaining ring (1) and remove the backtacking
lever (2).
- Mark with a pencil the instantaneous position of the
indented pulleys against the machine head in any position.
- Remove the indented belt (3) from the bottom indented
pulley
(4) first, and then remove the whole belt.
- Apply a new indented belt on the top indented pulley (5)
first.
- Turn both indented pulleys in the formerly marked positions
and apply the indented belt on the indented pulley (4).
- Tension the belt and mount the dismantled components in
the inverse order.
5
3.11
3.11.1
V-belt, motor - head
Tensioning
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
m
0m
l-2
10 N
The belt is correctly tensioned, when the opposite sides of
the belt approach one to another by up to 20 mm in applying
the force of 10 N. The belt is tensioned in turning respectively
the motor in its holder.
10 N
3.11.2
Replacing the V-Belt
Caution! Danger of injury!
Switch off the main switch! before starting the
setting operation, wait until the motor stops!
- Loosen the screw (1) of the positioner arrest (2) and tilt the
arrest.
- Unscrew the screws (3) of the handwheel.
- Unscrew the screws (4) of the belt guard and tilt the guard.
- Remove the belt guard of the motor and tilt the protections
against falling out the belt from the motor pulley.
- Replace the belt.
- Tension the belt (see par. 3.11.1).
3
2 1
4
3.12
3.12.1
To exchange the driving toothed belt
Caution! Danger of injury!
Switch off the main switch! before starting the
setting operation, wait until the motor stops!
1
2
Driving toothed belt
- Remove the machine head from the stand (uncouple the
motor cables, the machine head cable and screw off the
wood screw and the screw from the hinges).
- Remove the belt guard (1).
- Replace the belt (2).
22
3.13 Lubrication
"
!
#
$
3.13.1
Description
3.13.2
Refilling oil
3.13.3
Multiple oil use
From the lubricating tank (1) there issue three suction wicks.
The wick (2) lubricates the pin of the thread mechanism, the
wick (3) lubricates the needle mechanism and the wick (4)
lubricates the stitch length mechanism. The superfluous oil
from the needle and thread mechanisms is sucked off by the
wick (5) and lubricates the shifting wedge of the feeding
clutch.
The hook has its own oil reservoir (6). The superfluous oil
from the hook lubrication lubricates the driving gear of the
hook.
For lubricating the machine oil Esso SP-NK 10, DA 10 is used
or other oil with the same quality. When putting the machine
into operation, each mechanism of the machine is to be
lubricated with several drops of oil. Oil is only refilled thereafter
into the oil reservoirs using an oil can into the holes in the oil
level indicators.
The oil tank (1) of the central distribution is to be filled up to
the mark max.
The oil tank (2) of the hook lubrication is to be filled up to the
upper edge.
Oil which runs into the oil cup is collected in the collector (1)
and may be reused for refilling the oil reservoirs in the machine
- see par. 3.13.2.
The oil collector (1) with the collected oil is uscrewed and the
top part of the oil can (2) which is added in the machine
packing is screwed in. Oil is then refilled into the reservoirs on
the machine head and everything is put into the original
condition.
23
2
4. Thread trimming
A
4.1 Description of the trimming mechanism
3
1
4
12
6
5
B
During the trimming cycle, the moving trimming knife (1), in
an opportune moment, hooks up the sewing threads and pulls
them in the sense of the arrow (A) against the fixed knife (2)
until the threads are trimmed. The spring (3) holds the hook
thread after being trimmed off. The moving trimming knife (1)
is fastened on the holder (4) and the holder is fastened on the
shaft (5). This shaft is turned by means of the lever (6) under
the effect of the fork (13) fastened on the shaft (7), which is
shifted by the electromagnet (8) from its starting position in
the sense of the arrow (B). When moving back in the sense of
the arrow (C), the shaft (7) is shifted by the cam (9) through
the pickup roller (10) into the starting position. The spring
(11) maintains the mechanism in its starting position. The
electromagnet (12), in an opportune moment, loosens the
main tensioner. At the end of the trimming cycle, both
electromagnets (8 and 12) are switched off.
C
4.2 Setting the pickup roller
13
7
9
11
10
3
1 4
The holder of the pickup roller (1) is to be fixed in such a way
that it is positioned, in its starting position, between the shaft
(2) and the shaft (3), the respective gap „A“ = 0.2 to O.4 mm.
8
6
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
- With the loosened screw (4), put the holder of the pickup
roller (1) up to the stop against the bracket (5) and, at the
same time, the shaft (2) up to the stop against the shaft (3).
- With the holder (1) held on the stop, shift the shaft (2) in
such a way that there appears the gap „A“ = 0.2 to 0.4 mm,
and tighten the screw (4).
- Check the gap „A“ in shifting the armature (6).
2
5
4.3 Setting the cam
A
The position of the cam (1) against the shaft (2) is to be such,
so that when the adjusting pin is in contact with the shaft (4),
the protractor scale of the handwheel (6) shows just the angle
of 108°. If the pickup roller (5) is in its starting position of
rest, the clerarance between the roller (5) and the cam (1)
should be as small as possible but sufficient to prevent the
cam from getting into accidental contact with the roller.
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
5
4
2
8
3
1
6
108o
7
- Set the angle of 108° on the handwheel (6) and lock it with
the screw (7) which is included in the accessory of the
machine (tighten with care).
- Shift the pickup roller (5) in the sense of the arrow up to the
stop.
- Insert the adjusting pin (3), which is included in the
accessory, into the cam and turn the cam, until the pin (3)
gets the contact with the shaft (4).
- Insert a gauge having the thickness of 0.1 mm between the
cam (1) and the pickup roller (2) and shift the cam against
the gauge up to the stop. Tighten then the screw (8).
- Loosen the blocking of the handwheel, turn a bit the cam
and tighten the second fastening screw of the cam too.
24
8
3
6
4.4 Setting the fork
4
In the starting rest position of the trimming mechanism, when
the holder (1) is in contact with the console (2), the lever (3)
must be in contact with the stop (4).
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
9
7
5
1
- Shift the shaft (5), until the holder (1) strikes the bracket
(2).
- Loosen the screw (6) and (7).
- Shift the lever (3) to the stop (4) /mind the axial clearance of
the eccentric shaft (8)/ and tighten the screw (6).
- Slip on the fork (9) on the pin of the lever (3) and retighten
the screw (7).
2
2
1
4.5 Setting the moving knife
7
6
TThe movable trimming knife (1) is to be, in its starting rest
position, in alignment of its end with the edge of the fixed
trimming knife (2).It is to be set in height in such a way, so
that its bottom surface (3) passes above the surface (4) of
the middle part (5) of the hook with the clearance of about
0,3 mm.
8
4
5
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
10
11
9
3÷4 mm
- Loosen the screws (6) of the lever (7).
- Turn the movable trimming knife (1) in alignment with the
fixed knife.
- Tighten the screw (6) /the lever (7) must be leaning against
the stop (8) and the axial clearance of the trimmer shaft
must be maintained/.
- Loosen the screws (9) of the knife holder (10).
- In turning the screw (11), set the height of the movable
trimming knife (1). Tighten the screws (9).
4.6 Setting the fixed knife
1
The fixed trimming knife (1) is to be spring loaded through
swinging out of of the knife holder (2) in such a way, so that
it fits on the movable trimming knife at the distance of about
3 - 4 mm from the end of the movable knife. In its height
position, the fixed knife is to be set with its upper surface
above the movable trimming knife (3) by about 0,1 mm. The
knives need not to trim untensioned threads.
3
2
4
Caution! Danger of injury!
Switch off the main switch. Before starting the
setting operation, wait until the motor stops!
5
- With loosened screws (4), proceed to the height setting of
the knife.
- Tighten slightly the bottom screw (4).
- Set the angle of about 300° on the handwheel (5).
- Shift by hand the moving knife (3) into the marked position.
- In swinging out the knife holder (2) set by way of trial the
spring loading of the fixed trimming knife (1).
- Tighten both screws (4).
- Check the bearing spot of the moving trimming knife (3) on
the fixed trimming knife (1) and give it a correction, if needed.
300o
25
4.7 Setting the retaining spring of the hook thread
4
The retaining spring (1) holds the hook thread after having
performed the trimming. It is to be set in such a way that the
force necessary for pulling out the thread from the retaining
spring (1) is approximately equal to the force necessary for
pulling out the thread from the hook.
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
- In an emergency case, shape the retaining spring (1) in
such a way that it fits close with all its surface (without
wedge) onto the moving trimming knife (3) and so that,
with the slightly tightened screw (2), onto the moving
trimming knife without any pressure.
- Tighten the screw (2), until the necessary force for pulling
the thread from the retaining spring is attained. The pulling
force is tested using a screwdriver (4) according to the
illustration.
3
2
1
Caution!
The setting of the retaining spring (1) depends
on the setting of the hook thread tension and
differs then according to the respective sewing
category.
4.8 Setting the switching of electromagnets
The electromagnets of the trimming device and loosening of
the tensioner must work in accordance with the diagram. This
is ensured by setting the stopmotor (see the instructions for
use of the stopmotor).
4
5
1 - 1. position of the needle (135 on the handwheel);
2 - 2. position of the needle (64 on the handwheel)
3 - position of stopping the tensioner (10 ÷ 25 on the handwheel)
4 - movement of the pickup roller of the trimmer cam
5 - current of the trimming device electromagnet
6 - current of the tensioner loosening electromagnet
6
1
3
2
5. Lifting the top roller by electromagnet
5.1 Description
The core of the electromagnet, respectively its pin must be set
in such a way that the presser foot lifting is enabled.
5.2 Setting the electromagnet pin
1
4
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
2
A
B
3
5
- Unscrew the cap of the core (1) of the electromagnet.
- Shift the core (2) with the pin (3) and unscrew the locking
screw (4).
- Unscrew the pin (3) in the core (2) in the “A” direction up to
the stop.
- Push the core (2) into the magnet (5) in the “B” direction
up to the stop.
- In this position, set the maximum top roller lifting in the “B”
direction.
- Screw on and tighten the arresting screw (4).
- Screw on the cap (1).
26
5.3 Setting the electromagnet current
The time response of the current of electromag. has 2 phases:
- initial switching on (0,2 ÷ 0,5 s) - the maximum force
- maintaining (when keying)
It is necessary to set max. 40 % of keying (see
instructions for use of the stopmotor). With a
higher value thereof and with a long period of the
presser foot in its lifted position there is a danger
of electromagnet overheating.
5.4 Aseembly of the top roller lifting
electromagnet
2
4
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
3
- Remove the rear guard (3).
- Using the screws (1),fasten the electromagnet(2) on the
rear guard(3) with the given orientation of the outlet cable(4).
- Mount the rear guard (3).
- Connect the outlet cable (see par.7).
- Set the pin of the electromaghet (see par. 5.2).
- Set the current of the electromagnet (see par.5.3).
1
6. Backtacking using electromagnet
6.1 Description
The position of the electromagnet with regard to the
backtacking lever must be set in such a way that it enables the
maximum stitch length when sewing in forward and in rearward
sense. If this position is not correct, the length of the stitch
will be shortened in one or the other feed direction.
6.2 Electromagnet height setting
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
2
1
- Set the position of the electromagnet (2) in the upper
position of the grooves of the guard (3).
- Proceed to the mounting of the guard (3) with the magnet
on the machine head.
- Set the maximum stitch length and push the reverse
stitching lever into its bottom position (as with the reverse
stitching operation).
- In this position, the bar (5) must be in contact with the
roller (4) of the lever (6). Otherwise shift the electric magnet
(2) in the grooves of the guard (3).
5
3
6
4
6.3 Setting the position of push-buttons
Caution! Danger of injury!
Switch off the main switch! Before starting the
setting operation, wait until the motor stops!
- By loosening the screws (1), it is possible to set the position
of the holder of the push-buttons (2) in the sense of sewing.
6.4 Change of the function of push-buttons
2
The Function of the push-buttons can be changed in
accordance with the possibilities given by the stopmotor (see
instruction for use of stopmotor).
1
27
4
5
6
7
7. Connecting the electric elements on the
machine head
8
9
10
2
1
3
9
8
The connection of the electric elements (electromagnets,
backtacking, presser foot lifting, thread trimming, loosening
of the tensioner and push-buttons) is made by means of a
switchboard (1) fixed with its supporting plate (2) on the rear
side of the head by means of two distance screws (3) (In the
Fig., these electric elements are disconnected).
Connecting spots :
4 - backtacking electromagnet
5 - trimming electromagnet
6 - tensioner loosening electromagnet
7 - presser foot lifting electromagnet
8 - connector of push-button connecting
9 - connector of coupling the head with the stopmotor
1 0 - connecting cable of the head and stopmotor
Wiring diagram of connecting the electric elements of the
machine head.
4
5
6
7
8. Drive, control panel, position sensor
The detailed information concerning the drive, the control panel
and the setting of the position sensor is given in the manual
of the drive and of the control panel.
28
9.
Maintenance
Caution! Danger of injury!
The maintenance operations should be performed only with the machine switched off and with the motor stopped!
In the following table there are given the operations which should be performed and the respective time intervals between the
individual operations.
Operation
Time interval
Removal of the throat plate and its cleaning out.Cleaning out of the wheel feeder, hook and their
surrounding space. Removal of the residues of material and threads from the top roller.
Checking of the oil level in the oil tank of the hook.
1 day
1 week
Checking of the oil level in the central oil tank.
1 month
Checking the hook wear. Checking the function of the safety clutch against the hook overload.
6 months
Checking the V-belt and the indented belts.
1 year
10. Setting the machine according to the sewing category
10.1 Introduction
This sewing machine enables sewing operations within a large extent from the light up to the heavy-duty sewing. The parameters
of the respective sewing operation must be in accordance with the given machine setting which includes also the replacement of
some components, such as the needle, the throat plate insert, the top roller. For this reason, the setting of the machine is divided
into 4 categories:
1 ... light sewing
2 ... medium sewing
3 ... medium heavy-duty sewing
4 ... heavy-duty sewing
In the factory, where this machine has been manufactured, the machine has been set with respect to the standard parameters of
the required sewing category which is designed by the number included in the commercial designation of the machine. If the user
desires changing the given setting to another sewing category, this operation should be performed by a specialized mechanician.
The standard parameters of sewing are described in the following paragraph. The actual parameters of sewing inside the given
sewing category may be different, which means that the machine operative must adapt respectively the setting of the machine,
e.g. the tension of the upper thread.
29
10.2 Table of setting the machine according to the sewing category
Commercial designation of the machine 4180i - 5XX - X
Sewing
category
Standard machine setting
Standard sewing parameters
Thickness Number Stitch
Label
of one of mate- length number
material rial layers
of thread
PES
layer
Needle
size
Sewing Position
Width
speed of feeding of needle
lever pin
plate
insert
7)
2)
mm
mm
Feeder
pitch
of teeth
hole
Presser
top roller
diameter
1)
Presser
top roller
position
Thread tension
needle
thread
8)
0.01 mm
SPM
hook
thread
6)
mm
mm
mm
mm
N
N
-100
0.8
2
1.7
70
80
2500
1
1.2
0.4
35
10.5
3
1
-200
1
2
2.2
2.5
40
100
2500
1
1.5
0.4
35
10.5
4,5
1.5
-300
1.5
1-2
3.5
20
130
1600
-400
2
1-2
or
2-3
5
10
(20)
160
1600
Setting as per chapter
1
2
0.6
35
10.5
5-8
2
2
2.4
1.2
35
10.5
10- 12
2 - 2.5
3.3.2
3.5.3.2.2
3.6.6.1
3.6.6.2
6.4
6.4
3)
Instructions for service
Instructions for assembling
9)
9)
5)
Instructions manua
Splice of hook
4)
3.5.3.1.2
6.5
2.4
4.5
1) The standard setting of the machine for the categories 3 and 4 concerns a decorative stitching, when it is difficult to match
a good stitch interlocking with a faultless function of the thread trimming device. Otherwise, when sewing material of
considerable overall thickness, it will be necessary to increase the overtopping of the teeth above the needle plate and to
increase also the needle thread tension.
2) The thickness of a layer is measured using an engineer slide calliper with the pressure of jaws of about 10 N.
3) If the user will agree with the maximum stitch length of 5 mm, the pin of the feeding lever can be left in the position 1.
4) The values of tension are only orientative ones and it is necessary to adapt especially the tension of the hook thread
according to the stiffness of the material. An excessive tension of the threads when sewing soft materials causes material
wrinkling.
5) When performing decorative sewing, it is possible to use the hook thread having the label No 20 - the interval between the
two replacements of the hook bobbin will be double.
6) When changing markedly the sewing category together with changing the tension of the hook thread, it is necessary to
modify the tension of the retaining spring of the trimming device according to the paragraph 4.7.
7) When changing markedly the sewing category together with a marked change of the needle number, it is necessary to correct
the setting of the distance of the hook from the needle, according to the paragraph 3.1.3.
8) There are in use various types of feeders with the purpose of avoiding imprinting the teeth in the lining leather. Otherwise, it
is possible to use any feeder.
9) The splice with the so-called spur may be used with the sewing categories 100 and 200 and is designed for sewing thin
materials.
In the production factory , the gib without spur is mounted as standard.
When using the gib with the so-called spur, we recommend carrying out the setting of the pin of the thread mechanism (par.
3.2.4) for the sewing category 400.
30