Casio IT-3100 Hardware manual

CASIO
IT-3100 Series
Hardware Manual
(Version 1.02)
CASIO Computer Co., Ltd.
Copyright ©2008. All rights reserved.
September 2008
Table of the Contents
Chapter 1.
1.1
1.2
1.3
1.4
1.4.1
1.4.2
1.4.3
1.4.4
1.4.5
1.4.6
1.4.7
1.4.8
1.4.9
1.4.10
1.4.11
1.4.12
1.4.13
1.4.14
Chapter 2.
2.1
2.1.1
2.1.2
2.2
2.3
2.3.1
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
Chapter 3.
Chapter 4.
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.1.6
4.1.7
Editorial Record
Overview of the Products
Features
Available Models and Options
Options and Interfaces
External Views
IT-3100
HA-B30CHG
HA-B61IO
DT-9721CHGE
DT-9723LIC
AD-S10095A
AD-S42120B
HA-B34AT
HA-B90DCV
HA-B93PH
DT-888RSC
DT-887AXA
DT-380USB
HA-B80AX
Hardware Specifications
IT-3100
14-pin Serial Interface Connector
Reference for C-MOS Imager Performance
HA-B30CHG
HA-B61IO
DIP Switch Setting for HA-B61IO
DT-9721CHGE
DT-9723LIC
AD-S10095A
AD-S42120B
AD-S10095A
HA-B34AT
HA-B90DCV
HA-B93PH
Product Identification and Reference Numbers
Quality References
Environment Performance
IT-3100
HA-B30CHG
HA-B61IO
DT-9721CHGE
DT-9723LIC
AD-S10095A
AD-S42120B
2
5
6
6
7
10
11
11
13
14
16
16
17
17
18
19
19
19
20
20
20
21
21
27
28
31
32
35
36
36
37
38
39
40
40
40
41
42
42
42
43
43
44
44
45
45
4.1.8
4.1.9
4.1.10
4.1.11
4.2
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.7
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
4.3.7
4.3.8
4.3.9
4.3.10
4.3.11
4.4
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.4.6
4.4.7
4.5
4.5.1
4.5.2
4.5.3
4.5.4
4.5.5
4.5.6
4.5.7
4.5.8
Chapter 5.
5.1
5.2
5.3
Chapter 6.
6.1
HA-B34AT
HA-B90DCV
HA-B93PH
HA-B80AX
Electrical Performance
IT-3100
HA-B30CHG
HA-B61IO
DT-9721CHGE
DT-9723LIC
AD-S10095A
AD-S42120B
Mechanical Performance
IT-3100
HA-B30CHG
HA-B61IO
DT-9721CHGE
DT-9723LIC
AD-S10095A
AD-S42120B
HA-B34AT
HA-B90DCV
HA-B93PH
HA-B80AX
Reliability
IT-3100
HA-B30CHG
HA-B61IO
DT-9721CHGE
DT-9723LIC
AD-S10095A
AD-S42120B
Compliance
IT-3100
HA-B30CHG
HA-B61IO
DT-9721CHGE
DT-9723LIC
AD-S10095A
AD-S42120B
HA-B34AT
Cable Specifications
DT-888RSC
DT-887AXA
HA-B80AX
Precautions
Handling Precautions
3
45
46
46
46
47
47
47
48
48
48
49
49
50
50
50
51
51
52
52
53
53
54
54
55
56
56
58
58
59
59
59
59
60
60
61
61
62
62
63
63
64
65
65
67
68
69
69
No part of this document may be produced or transmitted in any form or by any means, electronic or
mechanical, for any purpose, without the express written permission of CASIO Computer Co., Ltd.
in Tokyo Japan. Information in this document is subject to change without advance notice. CASIO
Computer Co., Ltd. makes no representations or warranties with respect to the contents or use of this
manual and specifically disclaims any express or implied warranties of merchantability or fitness for
any particular purpose.
© 2008 CASIO Computer Co., Ltd. All rights reserved.
4
Editorial Record
Manual
Version no.
1.00
1.01
Date edited
Page
Content
August 2008
August 2008
all
6, 65
Original version
In Chapters 1 and 5, the explanation about DT-882RSC and
DT-883RSC cables is deleted because of phased out
products.
Option power cords for AD-S42120B are added in Chapter
1.2.
Explanation about DT-9020ADP AC Adaptor is deleted
because of phased out product.
In Chapter 1.2, the content in Table 1.2 is updated.
In Chapter 1.3, Figure 1.1 is updated.
In Chapter 2.1, the parameters of Bluetooth are added in
Table 2.1.
The description about the AC Adaptors, AD-S42120AE
and AD-S42120AE-CN is deleted,
7
all
1.02
September 2008
8
10
21
all
5
1.
1.1
Overview of the Products
Features
Supporting the outstanding development environment
• Windows® CE 5.0 English Version as the integrated OS
• Visual Studio 2005
• Visual Studio .NET 2003 (Windows® CE .NET Utilities v 1.1 for Visual Studio .NET 2003)
• eMbedded Visual C++ 4.0
Outstanding performance/Large memory
• High performance CPU
Marvell® PXA255 Application Processor (maximum 400 MHz)
• Large capacity memory
RAM
: 128MB
F-ROM : 96MB
Enhanced communication functions
• Enables WWAN, WLAN, etc. with a card available from third party.
• High speed infrared communication with IrDA Ver1.1
• Bluetooth® Version 1.2
Support industrial standard symbologies
• Readable 1D symbologies:
UPC-A, UPC-E, EAN8, EAN13, Codabar, Code11, Code39, Code93, Code128, ITF, MSI, IATA,
GS1 DataBar Omnidirectional, GS1 DataBar Limited, GS1 DataBar Expanded, GS1 DataBar
Stacked, GS1 DataBar Expanded Stacked
• Readable 2D symbologies:
PDF417, MicroPDF, Code49, Composite, Codablock F, TLC39, GS1 DataBar Stacked, GS1
DataBar Stacked Omnidirectional, GS1 DataBar Expanded Stacked, Aztec, DataMatrix,
Maxicode, QR Code
Various industrial standard interfaces
• SD card slot
• PC card slot
• 14-pin serial
• 8-pin serial (model dependant)
Improved durability
• Impact resistance to fall
: 1.2 m in height*
• Dust and Water-splash proof : IP54 level (compliant with IEC60529 International Standard)
* ; The drop durability height is a measured value resulting from actual testing. It does not necessarily guarantee the
product from damage.
6
1.2
Available Models and Options
Table 1.1
List of the available models
Model no.
IT-3100M53E
IT-3100M54E
IT-3100M55E
IT-3100M55U
IT-3100M56E
IT-3100M56U
IT-3100M53E-CN
IT-3100M54E-CN
IT-3100M55E-CN
IT-3100M56E-CN
Blueto
oth
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
MCR
Yes
Yes
Yes
Yes
Yes
-
C-MOS
Imager
Yes
Yes
Yes
Yes
Yes
Yes
RS-232C I/F
8-pin 14-pin
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Printer
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Remark
See note.
Note:
“-CN” in the “Model no.” box denotes that the model is dedicated for the final destination of China.
A note about the compliance with the Chinese “RoHS” requirement promulgated by the Ministerial
Decree No. 39 is accompanied in the carton box, the RoHS compliant seal is affixed on the body and
the seal of the packing material recycle marking is affixed on the carton box.
7
Table 1.2 List of the options
Model no.
HA-B61IO
HA-B61IO-CN
HA-B34AT
HA-B34AT-CN
HA-B30CHG
HA-B30CHG-CN
DT-9721CHGE
DT-9721CHGE-CN
DT-9723LIC
DT-9723LIC-CN
AD-S42120B
AD-S42120B-CN
AD-S10095AE
AD-S10095AU
AC-CORD-EU
AC-CORD-US
AC-CORD-TW
AC-CORD-KR
AC-CORD-AU
DT-827CAC
DT-827CAC-CN
DT-887AXA
DT-887AXA-CN
DT-888RSC
DT-380USB
HA-B80AX
HA-B80AX-CN
HA-B93PH
HA-B93PH-CN
HA-B92PCV
HA-B92PCV-CN
HA-B90DCV
Product
Bridge Satellite Cradle
Bridge Satellite Cradle
Battery Charger Car Mount Unit
Battery Charger Car Mount Unit
Cradle-type Battery Charger
Cradle-type Battery Charger
Battery Charger
Battery Charger
Battery Pack
Battery Pack
AC Adaptor
AC Adaptor
AC Adaptor with European
power cable
AC Adaptor with US power
cable
Power Cable
Power Cable
Power Cable
Power Cable
Power Cable
Car Power Cable
Car Power Cable
RS-232C Cross Cable
RS-232C Cross Cable
RS-422 Modular Cable
USB Cable
RS-232C Cross Cable
RS-232C Cross Cable
Formed Sheet Paper Holder
Formed Sheet Paper Holder
Splash Protect Cover
Splash Protect Cover
Screen Protect Cover
Remark
See note 1.
See note 1.
See note 1.
Single battery pack charger
See note 1.
See note 1.
DC12V/3.5A See note 3.
DC12V/3.5A See notes 1 and 3.
DC9.5V/1A See note 2.
DC9.5V/1A See Note 2.
For AD-S42120B and Europe
For AD-S42120B and US/Canada
For AD-S42120B and Taiwan
For AD-S42120B and Korea
For AD-S42120B and Australia
See note 1.
Cable length; 1.5 m, 9-pin male
Cable length; 1.5 m, 9-pin male See note 1.
Cable length; 1.0 m
Cable length; 2.0 m
For ActiveSync.
For ActiveSync See note 1.
See note 1.
See note 1.
Notes:
1. “-CN” in the “Model no.” box denotes that the model is dedicated for the final destination of
China. A note about the compliance with the Chinese “RoHS” requirement promulgated by the
Ministerial Decree No. 39 is accompanied in the carton box, the RoHS compliant seal is affixed
on the body and the seal of the packing material recycle marking is affixed on the carton box.
2. The AC Adaptor accompanies a power cable.
3. The AC Adaptor does not accompany a power cable.
8
The accessories in the table below are accompanied in each individual carton box of IT-3100 series.
Accessories accompanied in each dedicated option are not listed in the table below.
Table 1.3
Accessory
Accessory
Stylus
Neck strap and stylus holder
Hand strap
Battery pack
Roll paper
PC card fixers
58 mm Paper Width Adjuster
PC Card remover
User’s Guide
Q’ty
1
1
1
1
1
3
1
2
1
Remark
DT-9723LIC
In English, Chinese and Turkish
9
1.3
Options and Interfaces
Figure 1.1
10
1.4
External Views
1.4.1 IT-3100
Left
Front
Right
Rear
Figure 1.2
Notes:
• The C-MOS imager (item no. 25) comes with IT-3100M55E, IT-310055U, IT-3100M56E and
IT-3100M56U. For non-CMOS imager models, the 8-pin serial interface is available instead.
• The magnetic card reader (item no. 22) comes with IT-3100M54E, IT-3100M55E and
IT-3100M55U.
11
See the following table for names of each part and description.
Table 1.4
No.
1
2
Descriptions of the parts
Name
SD Memory Card Slot
L Program Key
3
Roll Paper Holder
4
Splash Protect Cover
and Paper Cutter
5
6
Power Key
Indicator 1 (Left side)
Indicator 2 (Right side)
7
8
Speaker
Brightness Sensor
9
LCD Panel/Touch
Screen
Stroke Keys
10
11
12
13
8-pin Serial Interface
Connector
R Program Key
Power Jack
14
IR Port
15
Battery Pack Cover
Lock Switch
Battery Pack Cover
PC Card Slot
16
17
18
19
20
21
22
23
24
25
Hand Strap Hook
14-pin Serial Interface
Connector
Power Terminals
Neck Strap Hooks
Magnetic Card Reader
Reset Switch
Screen Protect Cover
Mounting
CMOS Imager
Description
Slot for inserting SD memory card.
This key can be assigned to any function available. In the imager model, use
it to scan bar codes, etc.
Roll paper is placed in this holder. Use the optional Paper Holder when using
a formed sheet paper.
Printed roll paper is torn off here. The paper cutter is provided with a splash
protect cover. Open the cover when printing. The paper cutter is revealed
when the cover is opened.
Press this key to turn on or off the power.
This indicator lights green when charging the battery pack is complete or red
during charging.
This indicator flashes or lights according to the settings of the application
software installed in the terminal.
Generates audio sound and buzzer tone.
This sensor detects the brightness in the surroundings. The backlight and key
backlight can be controlled automatically according to settings. Be careful
not to inadvertently block the sensor.
Displays text, operations, indicators and so forth. In addition, operations can
be performed and data can be input using the stylus provided.
There are a total of 19 keys including function keys and numeric keys. Each
numeral or symbol on the key tops is backlit.
For connecting a bar code reader and so forth.
This key can be assigned to any function available.
The dedicated AC Adaptor is connected to this jack when charging the
lithium-ion battery pack.
This is used for IR communication with another terminal or the Bridge
Satellite Cradle.
Turn this switch when opening and closing the battery pack cover.
This is the cover for the battery compartment.
For connecting a PC card available from a third party. Remove the cover to
install a PC card.
Hook the hand strap here.
Provided for future use.
Terminals for supplying power from the Bridge Satellite Cradle or
Cradle-type Battery Charger.
Hook the neck strap here.
Magnetic cards are read by passing through this magnetic card reader.
Press to reset the terminal.
Remove the screws when attaching the Screen Protect Cover.
Reads 1D and 2D symbologies.
12
1.4.2 HA-B30CHG
The following external views show the Cradle-type Battery Charger (HA-B30CHG, HA-B30CHG
-CN).
Top
Front
Right
Rear
Bottom
Figure 1.3
Table 1.5
No.
1
2
3
4
5
Names of parts and the descriptions
Part Name
Power Status Indicator
Detection Switches
Power Supply Terminals
Power Switch
Power Jack
Description
This LED indicates the power status.
These switches are to detect the terminal being mounted in the charger.
These terminals are to provide the power to the terminal in the charger.
Turns on and off the power.
Power jack to connect the dedicated AC Adaptor for supplying the power.
13
1.4.3 HA-B61IO
The following external views show the Bridge Satellite Cradle (HA-B61IO, HA-B61IO-CN).
Top
Front
Right
Bottom
Figure 1.4
14
Rear
See Table 1.6 for names of each part and its description.
Table 1.6
No.
1
2
3
4
5
6
7
8
9
10
11
12
Names of parts and the descriptions
Part Name
Description
System Status Indicator This lamp indicates whether the system is operating normally. It indicates
Lamp
the system status and whether or not communication with the system can be
performed regardless of whether or not the terminal is mounted.
Off
: System is not operating.
Green
: System is operating.
Communication
This lamp shows when the terminal is performing communication.
Indicator Lamp
Off
: No communication being performed.
Green flashing : Communication in progress.
Red
: Problem with connection between Bridge Satellite and
the terminal.
Power Indicator Lamp This lamp indicates the power status and mounting status of the terminal.
Off
: Power off.
Green
: Power on and communication is in progress.
Red
: Power on, but the terminal is not mounted.
Terminal Detect
These switches detect a terminal when it is correctly mounted in the Bridge
Switches
Satellite Cradle.
IR Port
This port exchanges data with the terminal via IR port.
Power Contacts
Power is supplied to the terminal via these contacts.
Power Key
Turns on and off the power.
AC Adaptor Jack
Connect the dedicated AC Adaptor here to supply power.
RS-422 Port
This port is used when connecting with another Bridge Satellite Cradle.
RS-232C Port
This port is for connecting an RS-232C cable for connection to PC for
transfer of data and file. Use of the RS-232C port requires installation of the
special driver on PC.
USB Port
This port is for connecting a USB cable for connection to PC for transfer of
data and file. Use of the USB port requires installation of the special driver
on PC.
DIP Switches
Use these switches to configure the Bridge Satellite Cradle.
15
1.4.4 DT-9721CHGE
The following external view shows the Battery Charger (DT-9721CHGE, DT-9721CHGE-CN).
Figure 1.5
Note:
The above figure shows the DT-9721CHGE (DT-9721CHGE-CN) with a power cord available in
Japan. The power cord accompanied with the charger for overseas destinations is not in the same
form shown.
1.4.5 DT-9723LIC
The following external views show the Battery Pack (DT-9723LIC, DT-9723LIC-CN).
Figure 1.6
16
1.4.6 AD-S10095A
The following external view shows the AC Adaptor (AD-S10095AE, AD-S10095AU).
Figure 1.7
1.4.7 AD-S42120B
The following external view shows the AC Adaptor (AD-S42120BE, AD-S42120BE-CN).
Figure 1.8
Note:
The AD-S42120BE and AD-S42120BE-CN do not accompany a power cable.
17
1.4.8 HA-B34AT
The following external view shows the Battery Charger Car Mount Unit (HA-B34AT, HA-B34AT
-CN).
2
1
2
Figure 1.9
Note:
The figure above shows a view of HA-B34AT Battery Charger Car Mount Unit (gray part) and
HA-B30CHG Cradle-type Battery Charger being assembled together.
Table 1.7
Names of parts and the descriptions
No.
1
Part Name
Jack for Car Power Cable
2
Removal Buttons R and L
Description
Connect the dedicated Car Power Cable from the cigarette lighter in a
vehicle.
When remove the terminal, press the removal buttons on the left and
right sides of the Car Mounted Battery Charger.
18
1.4.9 HA-B90DCV
The following external view shows the Screen Protect Cover (HA-B90DCV).
Figure 1.10
1.4.10 HA-B93PH
The following external view shows the Formed Sheet Paper Holder (HA-B93PH, HA-B93PH-CN).
Figure 1.11
1.4.11 DT-888RSC
The following external view shows the RS-422 Modular Cable.
Figure 1.12
19
1.4.12 DT-887AXA
The following external view shows the RS-232C Cross Cable (DT-887AXA, DT-887AXA-CN).
Figure 1.13
1.4.13 DT-380USB
The following external view shows the USB Cable.
Figure 1.14
1.4.14 HA-B80AX
The following external view shows the RS-232C Cross Cable (HA-B80AX, HA-B80AX-CN).
Figure 1.15
20
2.
2.1
Hardware Specifications
IT-3100
Tables 2.1 to 2.4 explain the hardware specifications of the IT-3100 series (all models).
Table 2.1
Parameter
CPU/Memory
CPU
Operating system
RAM
FROM (system)
FROM (user)
Display
Device
Resolution
Backlight
Specification
Marvell® PXA255 runs at 400MHz
(maximum)
Microsoft®Windows® CE Ver. 5.0
128 MB
64 MB
32 MB (user area: approx. 30 MB)
3.5-inch advanced 2-way TFT color LCD
240 (Horizontal) x 320 (Vertical) dots
LED
Dot pitch
Font
Indicator
LED
Input
Keyboard
Control key
Programmable key
Touch panel
Key backlight
Ten keys (0 to 9), ENT, CLR, Fn, BS
Power key, Reset switch
2 ( on the left and right sides)
Plastic panel
Available
Brightness sensor
Available
Printer
Method
Paper width
Thermal line dot
80 mm or 58 mm
Printing width
Speed
Remark
Automatic control via the
brightness sensor
0.22 mm (H) x 0.22 mm (V)
Scalable fonts
2 pcs x 2-color LED in red and green
Automatic control with the
brightness sensor
(Programmable)
Used to control both display
backlight and key backlight.
The width of paper must be
preset with software prior to use
of the printer. In order to use
58mm paper, “58mm Width
Adjuster” must be installed first.
72 mm (for an 80 mm paper)
48 mm (for a 58 mm paper)
28 lines per second (Max.)
Continue.
21
See note 1.
Paper
Font size
Font types
Print function
IrDA
Standard
Method
Synchronization
Baud rate
Communication range
Bluetooth
Standard
Communication range
Frequency range
Output power
Transmit power
Emission designation
Modulation type
Number of channels
Channel spacing
Bandwidth
Antenna type
Antenna gain
8-pin serial interface
Interface
Synchronization
Baud rate
Output power to
external
Connector
Pin layout
Pin configuration table
Roll paper, formed papers (1-ply, 2-ply),
label paper
“x1”, “x1.5”, “x2”, “x3”, and “x4” sizes are
supported.
ANK/Symbologies (UPC-E, NW-7,
Code39, ITF, Code128, OCR-B,
user-defined characters x 128)
In white, black and reverse modes. Mixture
of different font sizes.
Use only CASIO recommended
papers.
IrDA Version 1.1
The module is installed on
the right side.
Half-duplex
Start and stop bits, frame synchronization
9,600, 115,200, 4 Mbps
0 (contact) to 1 m (0.25 m for 4 Mbps)
Bluetooth® specification Ver. 1.2
Approx. 3 m
2402 to 2480 MHz
Max. 3 dBm (PowerClass2)
1.0 mW
F1D
GFSK
79
1 MHz
1 MHz
IFA
0.35 dBi (maximum)
See note 2.
ITU code
RS-232C level interface
Start and stop bits synchronization
300, 600, 1200, 2400, 4800, 9600, 19.2K,
38.4K, 57.6K, 115.2K
5.0 V±10%, Max. 300 mA
See note 3.
TSC7926-18-30
Manufactured by Hosiden
Corporation
See Table 2.2.
See Table 2.2.
Continue to page 24.
22
Notes:
1. The printing speed has been measured under the following conditions;
•
Printing Kanji with 16-dot mode character and space is not allowed between lines.
•
One pry roll paper is used.
•
The battery pack is fully charged before printing.
2. The communication range can be varied depending on the surrounding environment.
3. IT-3100M55E, IT-3100M55E-CN, IT-3100M55U, IT-3100M56E, IT-3100M56E-CN and
IT-3100M56U do not integrate the serial interface.
4. A partner device connected to this interface must output data in the RS-232C signal level when
communicating with the terminal.
Table 2.2
Pin
1
2
3
4
5
6
7
8
8-pin serial interface pin configuration and pin layout
Signal
SD
RD
RS
CS
Vcc
SG
ER
DR
Direction
Remark
OUT
IN
OUT
IN
OUT 5V±10%, Max300mA
GND for signal and ground
-
OUT
IN
Pin Layout
Figure 2.1
Table 2.3
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
14-pin serial interface pin configuration and pin layout
Signal
SG
SG
NC
CI
NC
DR
SD
CD
RD
EXTSW
RS
VH
ER
VH
Direction
-
IN
-
IN
-
IN
OUT
IN
IN
OUT
IN
OUT
OUT
OUT
Remark
GND for signal and ground.
GND for signal and ground.
Output "L" when VH is ON. (Open drain
5V±10%, Max. 300mA
5V±10%, Max. 300mA
23
Pin Layout
Figure 2.2
14-pin serial interface
Interface
Synchronization
Baud rate
Output power to external
Connector
Pin layout
Pin configuration table
SD slot
SD memory card
PC card slot
Type
Power
Magnetic card reader
Standard
No. of tracks for
concurrent read-in
Sides of data reading
Orientation
Card running speed
Speaker
Alarm sound
Voice sound
Key click sound
Power
Operating battery
Memory backup battery
Battery life
RS-232C level interface
Start and stop bits synchronization
300, 600, 1200, 2400, 4800, 9600,
19.2K, 38.4K, 57.6K, 115.2K
5.0 V±10%, Max. 300 mA
A3A-14DA-2SV
See note 4.
Manufactured by Hirose Electric
Co., Ltd
See Table 2.3.
See Table 2.3.
1 slot
PC card Type I/II (3.3V/5.0V)
Max. 500 mA at 3.3V
Max. 1,000 mA at 5.0V
ISO Tracks 1, 2, 3 (ISO7811)
3
Both
One direction (left to right with the
front side being faced to the operator)
10 to 150 cm per second
70 dB or greater
60 dB or greater
50 dB or greater
Lithium-ion battery x 1
Lithium rechargeable battery x 1
Approx. 15 hours
Approx. 12.6 hours
Continue.
24
7.4 V 2,200 mAH.
Built-on board/irreplaceable.
- JEITA operation mode A.
- See note 5.
- JEITA operation mode D.
- See note 5.
Memory backup
RAM
RTC
10 minutes while replacing the
operating battery.
See note 6.
1 day from when operating battery
low warning appears.
1 day from when operating battery
low warning appears.
Charging the operating battery
Ways to charge the
Use AC Adaptor (AD-S10095A) while the
battery pack
battery pack is being installed in the terminal.
Use the Cradle-type battery charger while the
battery pack is being installed in the terminal.
Use the Battery Charger (DT-9721CHGE,
DT-9721CHGE-CN) to charge the battery
pack alone.
Charge method
Constant current and constant voltage
Charge voltage
8.4 V±1%
Charge current
Approx. 400 mA
Charge time
Approx. 8 hours (for DT-9723LIC,
DT-9723LIC-CN)
Approx. 72 hours (Memory backup)
During charging : LED ON in red
Charge indication
After charging
: LED ON in green
complete
CMOS Imager
Method
300,000 pixels, monochrome
Emitting window
Redirected downward at 45 degree
Resolution
1D symbologies
: 0.15 mm
Stacked 2D symbologies
: 0.169 mm
Matrix 2D symbologies
: 0.339 mm
PCS
1D symbologies
: 0.45 or greater
Stacked 2D symbologies
: 0.45 or greater
Matrix 2D symbologies
: 0.45 or greater
Depth
1D symbologies
: 40 to 410 mm
Stacked 2D symbologies
: 50 to 250 mm
Matrix 2D symbologies
: 60 to 150 mm
Readable width
See Chapter 2.1.2 “Reference for C-MOS
Imager Performance”.
Readable symbology
Refer to IT-3100 Series Software Manual.
25
See note 7.
See note 8.
Notes:
4. When the battery pack is a brand-new charged fully, and the surrounding temperature is in
ordinary level.
5. When the backup battery is a brand-new, and the surrounding temperature is in ordinary level.
6. When the terminal’s power is turned off. The memory backup battery is a brand-new, and the
surrounding temperature is in ordinary level.
7. When the terminal’s power is turned off. The battery pack is a brand-new, and the surrounding
temperature is in ordinary level.
8. A period of time until when the memory backup battery becomes fully charged. The operating
battery (DT-9723LIC) is being installed in the terminal, and the surrounding temperature is in
ordinary level.
Weight and Dimensions
Table 2.4
Model no.
IT-3100M53E, M53E-CN
IT-3100M54E, M54E-CN
IT-3100M55E, M55E-CN,
M55U
IT-3100M56E, M56E-CN,
M56U
Dimensions
Approx. 80 (w) x 199.5 (d) x 28 (h) mm
(See note 1.)
Approx. 108 (w) x 265 (d) x 68 (h) mm
(See note 2.)
Approx. 80 (w) x 229.5 (d) x 28 (h) mm
(See note 1.)
Approx. 108 (w) x 295 (d) x 68 (h) mm
(See note 2.)
Approx. 80 (w) x 229.5 (d) x 28 (h) mm
(See note 1.)
Approx. 145 (w) x 295 (d) x 70 (h) mm
(See note 2.)
Approx. 80 (w) x 199.5 (d) x 28 (h) mm
(See note 1.)
Approx. 145 (w) x 265 (d) x 70 (h) mm
(See note 2.)
Weight
Approx. 530g (See note 3.)
Approx. 635g (See note 4.)
Approx. 580g (See note 3.)
Approx. 680g (See note 4.)
Approx.600g (See note 3.)
Approx. 700g (See note 4.)
Approx. 550g (See note 3.)
Approx. 655g (See note 4.)
Notes:
1. The paper holder and other extruding parts on the terminal are excluded.
2. The paper holder and other extruding parts on the terminal are included.
3. The paper holder and hand strap are excluded. The lithium-ion battery pack is installed in the
terminal.
4. The paper holder and lithium-ion battery pack installed are included. The hand strap is excluded.
26
2.1.1 14-pin Serial Interface Connector
Figure 2.3
Figure 2.4
27
2.1.2 Reference for C-MOS Imager Performance
The CMOS imager performance reference is provided in this chapter as a guide to be utilized by the
user. The user can refer to these reference values in the table for his or her specific business
application. All the reference values have been came out from the assessment tests carried out under
the basic performance conditions below. However, it does not necessarily imply that the values are
guaranteed and optimum to any kind of business applications. They are intended for use by the user
as a reference only.
Table 2.5
Symbology
1D
Code39
UPC
2D
PDF417
(Stacked)
2D
(Matrix)
DataMatri
x
QR
Maxicode
Resolution
Range
(mm)
6 mil (0.15 mm)
8 mil (0.20 mm)
10 mil (0.254
mm)
13 mil (0.33 mm)
15 mil (0.38 mm)
20 mil (0.5 mm)
40 mil (1.0 mm)
13 mil (0.33 mm)
6.6 mil (0.168
mm)
8 mil (0.20 mm)
10 mil (0.254
mm)
15 mil (0.38 mm)
20 mil (0.5 mm)
13 mil (0.33 mm)
15 mil (0.38 mm)
20 mil (0.5 mm)
13 mil (0.33 mm)
15 mil (0.38 mm)
20 mil (0.5 mm)
70 to 105
60 to 135
50 to 200
35 mil (0.889
mm)
No. of read digits
A:
B:
C:
Maximum Recommen
Maximum
(close)
ded
12
12
21
5
12
22
5
10
20
Remark
60 to 200
40 to 210
70 to 260
90 to 410
60 to 200
60 to 115
5
2
2
2
11
97
10
8
8
5
11
100
19
17
16
12
11
2000
ECL4
60 to 135
50 to 165
95
100
100
100
2000
2000
ECL4
ECL4
70 to 210
80 to 250
60 to 105
60 to 125
80 to 155
60 to 105
60 to 130
60 to 145
52
50
100
97
95
100
97
95
50
50
100
100
100
100
100
100
1800
1500
1152
1152
1152
1600
1600
1600
50 to 210
52
50
138
ECL4
ECL4
ECC200
Max. 88
x 88 cel.
Max.
model
2M
version
20
ECC
Continue.
28
Angle
Pitch
Skew
Dead
zone
Tilt
1D (Code39 10 mil (0.25 mm))
2D Stacked
(PDF417 10 mil (0.25 mm))
2D Matrix
(Aztec 20 mil (0.5 mm))
1D (Code39 10 mil (0.25mm))
2D Stacked
(PDF417 10 mil (0.25 mm))
2D Matrix (Aztec 20 mil (0.5
mm))
Pitch and Skew
1D
(Code39 10 mil (0.25 mm))
2D Stacked
(PDF417 10 mil (0.25 mm))
2D Matrix
(Aztec 20 mil (0.5 mm))
±35°
±35°
At 110 mm from the LED emission port.
At 110 mm from the LED emission port.
±35°
At 110 mm from the LED emission port.
±40°
±40°
At 110 mm from the LED emission port.
At 110 mm from the LED emission port.
±35°
At 110 mm from the LED emission port.
±5°(Pitch
and Skew)
360°
At 110 mm from the LED emission port.
At 110 mm from the LED emission port.
360°
At 110 mm from the LED emission port.
360°
At 110 mm from the LED emission port.
PCS
1D
(Code39 10 mil (0.25 mm))
2D Stacked
(PDF417 10 mil (0.25 mm))
2D Matrix
(MaxiCode 35 mil (0.889 mm))
Surrounding illumination
100 to 80,000 Lux.
Visible angle
V_Angle = 26°, H_Angle = 35°
Operating temperature (Image sensor)
High temperature 50 ºC
Low temperature -10 ºC
0.45
or greater
0.45
or greater
0.45
or greater
29
5
100
52
Basic read conditions:
Test chart
Resolution
PCS
Depth
Pitch angle
Skew angle
Tilt angle
Surrounding temperature
Surrounding humidity
Surrounding illumination
Background of the symbol
Conditional Judgment
: Dedicated test pattern (1D, 2D Stacked)
: 1D; 0.25 mm, 2D; 0.5 mm
: 0.9 or greater
: 110 mm from the LED emission port
: α = 0 degree
: β = 10 degree
: γ = 0 degree
: 25 ºC
: 30 to 50 %
: 450 to 550 Lux.
: White
: Readable 7 times or more per 10 times of scanning
Figure 2.5
30
2.2
HA-B30CHG
The following table explains about the specifications of the Cradle-type Battery Charger
(HA-B30CHG, HA-B30CHG-CN).
Table 2.6
Display
Input
Power
Parameter
Status LED No. of LEDs
No. of display
colors
Display content
Detection switch for the terminal
Input from
Input voltage
AC adaptor Consumption
current
Plug
AC Adaptor
Input from
cigarette
lighter
Charge/Pow
er supply
Cable
Output voltage
Output current
Charge method
Charge time
Specification
1
2
In red and green
Power status (“POWER”)
Push switch
DC 12V±5%
Approx. 2,100 mA
EIAJ RC-5320A Class 4
AD-S42120BE
AD-S42120BE-CN
DT-827CAC
DT-827CAC-CN
DC10V±10%
1,800 mA (maximum)
Constant voltage
Approx. 8.0 hours
Power supply
terminal
Power
supply
Weight
Dimensions
Remark
While supplying power
or transmitting data.
Center pin; plus
See note 1.
With the current limiter
For DT-9723LIC,
DT-9723LIC-CN
See note 2.
GND
Approx. 630 g
Approx. 130 (W) x 206 (D) x 104 (H) mm
Notes:
1. The cable DT-827CAC (or DT-827CAC-CN) is used to supply the power to HA-B30CHG (or
HA-B30CHG-CN) from the cigarette lighter installed in a vehicle.
2. “Power supply terminal” is located on your left side of the charger when you face to the front
side with the power switch being located on your right side.
31
HA-B61IO
The following tables explain about the specifications of the Bridge Satellite Cradle (HA-B61IO,
HA-B61IO-CN).
Table 2.7
Parameter
Standard
Comm. method
Synchronization
Specification
Remark
IrDA Ver. 1.1 compatible
Half duplex
Start and stop bits method, Frame
synchronization
9600, 115.2 Kbps, 4 Mbps
See note 1.
(maximum)
USB Ver. 1.1 compatible
12 Mbps (maximum)
1. VBus
1
2
2. –Data (D-)
1
2
3. +Data (D+)
4
3
4. GND
4
3
Comm. speed
RS-422
USB connector type B
Full duplex
Start and stop bits method
115.2 Kbps
Comm. method
Synchronization
Comm. speed
Connector
SG ER
S
SD RD
S
C
5 4 3 2 1
9 8
6
CIC CSC RS D
D-Sub 9-pin (female)
Full duplex
Start and stop bits method
115.2 Kbps
Comm. method
Synchronization
Comm. speed
Connector
Comm. method
Synchronization
Comm. speed
IN
Display
Status LED
No. of LEDs
No. of display colors
Display content
Continue.
32
RD0-
RDO+
66 55443 32 21 1
RSO+
RSO-
SDO-
66 55 44332 21 1
SDO+
RDI-
OUT
RJ-45 compatible (6 pins)
3
2
System operation status (“LINE”)
Comm. status (“DATA”)
Power status (“POWER”)
RSI+
RS-232C
Standard
Comm. speed
Connector
RSI-
USB
SDI+
IrDA
SDI-
Interface
RDI+
2.3
Red and green
Refer to “Status
Indication with
LEDs”.
Input
Power
DIP switch
Detection switch for the terminal
Input from AC Input voltage
adaptor
Consumption current
Plug
AC Adaptor
Charge/
Power supply
8 switches
Push switch
DC 12V±5%
Approx. 2,200 mA
EIAJ RC-5320A Class 4
AD-S42120BE
AD-S42120BE-CN
DC 10V±5%
1,800 mA (maximum)
Constant voltage
Approx. 8.0 hours
Output voltage
Output current
Charge method
Charge time
Power supply
terminal
See page 35.
While supplying power
or transmitting data.
Center pin; plus
With the current limiter
For DT-9723LIC,
DT-9723LIC-CN
See note 2.
Power supply GND
terminal
Weight
Dimensions
Approx. 660 g
Approx. 130 (W) x 206 (D) x 104 (H) mm
Notes:
1. The maximum communication speed at 4 Mbps is possible only when the terminal is connected
to Host PC via the USB interface.
2. “Power supply terminal” is located on your left side when you face to the front side of the
Cradle with the power switch being located on your right side.
33
Status Indication with LEDs
Various operational statuses on the Bridge Satellite Cradle (HA-B61IO, HA-B61IO-CN) can be
displayed using the LEDs. The following table describes LED modes and their meanings.
Table 2.8
Parameter
LED
Power status indicator
Power OFF
(“POWER”)
IT-3100 is not mounted
IT-3100 is mounted
Comm. status indicator Break of communication
(“DATA”)
Connection between cradle
and PC is not valid.
Communication is in progress
Line status indicator
No comm. with IT-3100 or
(“LINE”)
abnormality of the system
Communication is in progress
with IT-3100.
34
Specification
LED OFF
LED ON in red
LED ON in green
LED OFF
LED ON in red
LED flash in green
LED OFF
LED ON in green
Remark
2-color LED
2-color LED
2.3.1 DIP Switch Setting for HA-B61IO
The DIP switch is located on the bottom side of the Bridge Satellite Cradle (HA-B61IO,
HA-B61IO-CN). Change the ON/OFF settings according to your required system configuration. The
new settings do not go into effect until the power switch is turned off and then back on again.
Figure 2.6
Note:
Other DIP switch settings are used for testing and inspection purposes. Because of this, you should
never use any DIP settings other than those described above.
35
2.4
DT-9721CHGE
Following tables explain about the specifications of the Battery Charger (DT-9721CHGE,
DT-9721CHGE-CN).
Table 2.9
Parameter
Charge method
Charge period
Consumption power
Input
Weight
Dimensions
Specification
Fixed voltage-and-current
Approximately 3 hours until the LED goes out
18 W
39 VA (at AC240V)
Approx. 140 g
Approx. 56 (W) x 44 (H) x 107 (D) mm
Remark
With the current limiter
See note.
Note:
When the LED goes out, charging the battery is complete nearly 90 percent from its fully charged
level. Leave the battery pack on the charger for another one hour after the LED went out to make the
battery pack be fully charged.
Status Indication with LEDs
The following table explains the status indicated by the LEDs on the Battery Charger
(DT-9721CHGE, DT-9721CHGE-CN).
Table 2.10
Parameter
LED
Power status indicator
(“POWER”)
Charge status indicator
(“DATA”)
2.5
Specification
Power to the charger is not supplied.
Power to the charge is supplied normally.
Charging the battery is completed
Charging the battery started.
Remark
LED OFF
LED ON in green
LED OFF
LED ON in orange
DT-9723LIC
The following table explains about the specifications of the Battery packs (DT-9723LIC,
DT-9723LIC-CN).
Table 2.11
Parameter
Rated capacity
Specification
2,200 mAh
Rated output voltage
Weight
Dimensions
7.4 V
Approx. 110 g
Approx. 39 (W) x 21 (H) x 71 (D) mm
36
Remark
- Discharge at the rate of
0.2C
- Discharge cut-off voltage at
5.0V
2.6
AD-S10095A
The following table explains the hardware specifications of AC Adaptors (AD-S10095AE,
AD-S10095AU).
Table 2.12
Parameter
Original manufacturer’s model no.
Specification
SA115B-09U
Input requirements
AC100 to 240V
AC90 to 264V
50 Hz
400mA (Max.)
DC9.5V±5%
DC1.0A
0A
Output requirements
Efficiency
Rated input voltage
Input voltage tolerance
Nominal frequency
Input current
Rated output voltage
Rated output current
Minimum output
current
No load power
consumption
Load regulation
Ripple noise
75% (minimum)
0.5 W or less
Less than ±5%
150 mVp-p (max.)
75% (minimum)
Dielectric strength
Insulation resistance
Leakage current
Dimensions
Weight
AC3.0 KV/5mA
DC500V 100MΩ or more
0.25 mA or less
Approx. 78 (D) x 50 (W) x 30 (H) mm
Approx. 118 g
37
Remark
Manufactured by
Sino-American Electronic Co.,
Ltd.
47 to 63 Hz
100VAC/50Hz with full road
- Input 240VAC/50Hz
- Ambient temperature 25ºC
Output 9.5VDC
Input 100VAC/50Hz with full
road
Input 240VAC/50Hz with full
road
1 second
1 minute
Input 240VAC/50Hz
2.7
AD-S42120B
The following table explains the hardware specifications of the AC Adaptors (AD-S42120BE,
AD-S42120BE-CN).
Table 2.13
Parameter
Original manufacturer’s model no.
Specification
SA145A-1240U-6
Type
Input
requirements
Switching regulator
100 to 240VAC
90 to 264VAC
50 or 60 Hz
47 to 63 Hz
1200mA
(maximum)
0.5W or less
Rated input voltage
Input voltage tolerance
Nominal frequency
Frequency tolerance
Input current
No load power
consumption
(Off mode)
Inrush current
Output
requirements
Protections
Hi-Pot Test
(Dielectric
strength)
Insulation
resistance
Dimensions
Weight
80A or less
Average efficiency
83.6% (minimum)
Leakage current
Rated output voltage
Rated output current
Rated output power
Minimum output
current
Line regulation
0.25 mA or less
DC12V
DC3.5A
42W
0A
Load regulation
Ripple noise
Over load protection
current
Over voltage protection
±5% or less
100 mVp-p or less
4.2 to 6.2 A
±2% or les
Clamp 190% output
voltage maximum
AC3.0 KV for 1 second, 5mA (leak current) or
less
DC500V for 1 minute, 100MΩ or more
Approx. 111 (D) x 50 (W) x 31 (H) mm
Approx. 275 g
38
Remark
By Sino-American
Electronic Co., Ltd.
At input 100VAC/50Hz
with full load
At input 240VAC/50Hz
- At input 100VAC to
240VAC
- At cold start, maximum
load.
- At input 115VAC/60Hz and
230VAC/50Hz with 25%,
50%, 75% and 100% load
At input 240VAC/50Hz
At full load and ±10% input
voltage
At O/P=12VDC, full load
At input 100 to 240VAC
2.8
AD-S10095A
Table 2.14
Parameter
Original manufacturer’s model no.
Specification
SA115B-09U
Input requirements
Rated input voltage
Input voltage
tolerance
Nominal frequency
Input current
AC100 to 240V
AC90 to 264V
Rated output
voltage
Rated output
current
Minimum output
current
No load power
consumption
DC9.5V±5%
Load regulation
Ripple noise
75% (minimum)
Less than ±5%
150 mVp-p (max.)
Output
requirements
Efficiency
50 Hz
400mA (Max.)
47 to 63 Hz
100VAC/50Hz with full
road
DC1.0A
0A
0.5 W or less
75% (minimum)
Dielectric strength
Insulation resistance
Leakage current
Dimensions
Weight
Remark
By Sino-American
Electronic Co., Ltd.
AC3.0 KV, 5mA
DC500V 100MΩ or more
0.25 mA or less
Approx. 78 (D) x 50 (W) x 30 (H) mm
Approx. 118 g
39
Input 240VAC/50Hz
Ambient temperature
25ºC
Output 9.5VDC
Input 100VAC/50Hz
with full road
Input 240VAC/50Hz
with full road
1 second
1 minute
Input 240VAC/50Hz
2.9
HA-B34AT
The following table explains about the specifications of the Battery Charger Car Mount Unit
(HA-B34AT, HA-B34AT-CN).
Table 2.14
Weight
Dimensions
Specification
Approx. 700 g
Approx. 130 (W) x 206 (D) x 104 (H) mm
Remark
In the status to mount on
Cradle-type Battery Charger.
2.10 HA-B90DCV
The following table explains about the specifications of the Screen Protect Cover.
Table 2.15
Weight
Dimensions
Specification
Approx. 28 g
Approx. 94 (W) x 85 (D) mm
Remark
Projection is not included.
2.11 HA-B93PH
The following table explains about the specifications of the Formed Sheet Paper Holder
(HA-B93PH, HA-B93PH-CN).
Table 2.16
Weight
Dimensions
Specification
Approx. 55 g
Approx. 108 (W) x 47 (D) x 21 (H) mm
40
Remark
Projection is not included.
3.
Product Identification and Reference Numbers
On the back of the terminal and its options (major options only), there is a bar code and numbers
printed on label as shown in Figure 3.1 below.
This bar code is represented by 15 digits of Code128 symbology and by alphanumeric characters
beneath the bar code. The numbers 1 to 9 in the figure represent identification and references of the
terminal while the numbers 10 to 14 represent a manufacturing reference reserved by the
manufacturer. See the figure below for respective meanings.
1
2
3
4
5
6
7
8
Serial number of terminal in
5 digits
10
9
11
12
13
14
Manufacturing references
(reserved by the manufacture)
Production month of the year (1 to 9, A, B, or C)
Production year (last digit only), Ex. 0 represents the year 2000.
Model number (two digits in alphanumeric)
6C: IT-3100M53E, M53E-CN
6D: IT-3100M54E, M54E-CN
6E: IT-3100M55E, M55E-CN
6F: IT-3100M55U
8A: IT-3100M56E, M56E-CN
8B: IT-3100M56U
75: HA-B61IO
76: HA-B30CHG
Figure 3.1
41
15
Check
digit
4.
Quality References
This chapter describes about references of the terminal and its dedicated major options concerned
with environmental performance, compliance, mechanical, electric durability, and etc.
4.1
Environment Performance
4.1.1 IT-3100
The following table explains environmental performance on the IT-3100 series (all models).
Table 4.1
Parameter
Temperature
Operation
For quality print
Specification
-20 to 50 ºC
Condition
0 to 40 ºC while mounting on
Cradle. See note 1.
HS360, ODT70TC-RAK,
F200UW6, AFP235
HG56S, TLC00
0 to 50 ºC
5 to 35 ºC
-20 to 70 ºC
Non-operation
Humidity
Operation
10 to 80 % RH
Non-operation
5 to 90 % RH
Storage in carton box
Temperature
-20 to 60 ºC
Humidity
90 % RH or less
Dust and water-splash proof
IP54 level (compliant with IEC60529)
No condensation.
No condensation.
See note 2.
Notes:
1. It is recommended to check the print quality in the environment including at low temperature
where the terminal is operated before starting the use.
2. All covers on the terminal must be closed.
42
4.1.2 HA-B30CHG
The following table explains environment performance on the Cradle-type Battery Charger
(HA-B30CHG, HA-B30CHG-CN).
Table 4.2
Parameter
Temperature
Operation
Storage
Humidity
Operation
Storage
Storage in carton box
Temperature
Humidity
Specification
Condition
0 to 40 ºC
-10 to 50 ºC
30 to 80 % RH
30 to 90 % RH
-10 to 50 ºC
30 to 90 % RH
No condensation
No condensation
4.1.3 HA-B61IO
The following table explains environment performance on the Bridge Satellite Cradle (HA-B61IO,
HA-B61IO-CN).
Table 4.3
Parameter
Temperature
Operation
Storage
Humidity
Operation
Storage
Storage in carton box
Temperature
Humidity
Specification
Condition
0 to 40 ºC
-10 to 50 ºC
30 to 80 % RH
30 to 90 % RH
-10 to 50 ºC
30 to 90 % RH
43
No condensation
No condensation
4.1.4 DT-9721CHGE
The following table explains environment performance on the Battery Charger (DT-9721CHGE,
DT-9721CHGE-CN).
Table 4.4
Parameter
Temperature
Operation
Storage
Humidity
Operation
Storage
Storage in carton box
Temperature
Humidity
Specification
Condition
0 to 40 ºC
-10 to 50 ºC
30 to 80 % RH
30 to 90 % RH
-10 to 50 ºC
90 % RH or less
No condensation
No condensation
4.1.5 DT-9723LIC
The following table explains environment performance on the Battery Packs (DT-9723LIC,
DT-9723LIC-CN).
Table 4.5
Parameter
Temperature
Operation
Storage
Humidity
Operation
Storage
Storage in carton box
Temperature
Humidity
Specification
Condition
Compatible with the temperature
range for IT-3100 during discharge, or
for the battery chargers during charge.
See Table 4.1 for discharge. Or, Table
4.2 or 4.3 for charge.
Compatible with the temperature
range for IT-3100. See Table 4.1.
Compatible with the humidity range
for IT-3100 during discharge, or for
the battery chargers during charge.
See Table 4.1 for discharge. Or, Table
4.2 or 4.3 for charge.
Compatible with the humidity range
for IT-3100. See Table 4.1.
-10 to 50 ºC
90 % RH or less
44
No condensation
4.1.6 AD-S10095A
The following table explains environment performance on the AC Adaptors (AD-S10095AE,
AD-S10095AU).
Table 4.6
Parameter
Temperature
Operation
Storage
Humidity
Operation
Storage
Specification
Condition
0 to 50 ºC
-20 to 80 ºC
20 to 85 % RH
10 to 95 % RH
4.1.7 AD-S42120B
The following table explains environmental performances on the AC Adaptors (AD-S42120BE,
AD-S42120BE-CN).
Table 4.7
Parameter
Temperature
Operation
Storage
Humidity
Operation
Storage
Specification
Condition
0 to 40 ºC
-20 to 60 ºC
20 to 80 % RH
10 to 90 % RH
4.1.8 HA-B34AT
The following table explains environment performance on the Battery Charger Car Mount Unit
(HA-B34AT, HA-B34AT-CN).
Table 4.8
Parameter
Temperature
Operation
Storage
Humidity
Operation
Storage
Storage in carton box
Temperature
Humidity
Specification
Condition
0 to 40 ºC
-40 to 85 ºC
30 to 80 % RH
30 to 95 % RH
-10 to 50 ºC
90 % RH or less
45
No condensation
No condensation
4.1.9 HA-B90DCV
The following table explains environment performance on the Screen Protect Cover.
Table 4.9
Parameter
Temperature
Non operation
Humidity
Non operation
Storage in carton box
Temperature
Humidity
Specification
Condition
-20 to 70 ºC
5 to 90 % RH
No condensation
-20 to 60 ºC
90 % RH or less
No condensation
4.1.10 HA-B93PH
The following table explains environment performance on the Formed Sheet Paper Holder
(HA-B93PH, HA-B93PH-CN).
Table 4.10
Parameter
Temperature
Non operation
Humidity
Non operation
Storage in carton box
Temperature
Humidity
Specification
Condition
-20 to 70 ºC
5 to 90 % RH
No condensation
-20 to 60 ºC
90 % RH or less
No condensation
4.1.11 HA-B80AX
The following table explains environment performance on the RS-232C Cross Cable (HA-B80AX,
HA-B80AX-CN).
Table 4.11
Parameter
Storage in carton box
Temperature
Humidity
Specification
-10 to 50 ºC
90 % RH or less
46
Condition
No condensation
4.2
Electrical Performance
4.2.1 IT-3100
The following table explains electrical performance on the IT-3100 series (all models).
Table 4.12
Parameter
Power consumption
Anti-static strength
Malfunction
Destruction
Specification
DC 4.5A, 7.4V to 10.0V
±6 KV
±12 KV
Remark
150 pF/330 ohm
4.2.2 HA-B30CHG
The following table explains electrical performance on the Cradle-type Battery Charger
(HA-B30CHG, HA-B30CHG-CN).
Table 4.13
Parameter
Current consumption
Specification
Approx. 0.1 A
Approx. 2.2 A
Voltage
Anti-static strength
Malfunction
Destruction
Line noise strength
(Level of malfunction)
DC12V±5%
Power interruption
±6 KV
±12 KV
1,000 V
Remark
When IT-3100 is not mounted on.
While supplying power and
transmitting data.
150 pF/330 ohm
-
10 milliseconds or less
47
Pulse frequency
Burst cycle
No. of pulses
Burst period
: 5 KHz
: 300 milliseconds
: 75 pcs
: 15 milliseconds
4.2.3 HA-B61IO
The following table explains electrical performance on the Bridge Satellite Cradle (HA-B61IO,
HA-B61IO-CN).
Table 4.14
Parameter
Current consumption
Specification
Approx. 0.1 A
Approx. 2.2 A
Voltage
Anti-static strength
Malfunction
Destruction
Line noise strength
(Level of malfunction)
DC12V±5%
Power interruption
±6 KV
±12 KV
1,000 V
Remark
When IT-3100 is not mounted on.
While supplying power and
transmitting data.
150 pF/330 ohm
-
Pulse frequency
Burst cycle
No. of pulses
Burst period
: 5 KHz
: 300 milliseconds
: 75 pcs
: 15 milliseconds
10 milliseconds or less
4.2.4 DT-9721CHGE
The following table explains electrical performance of the Battery Charger (DT-9721CHGE,
DT-9721CHGE-CN).
Table 4.15
Parameter
Anti-static strength
Malfunction
Destruction
Power interruption
Specification
8 KV
10 KV
200 milliseconds
Remark
200pF/100 ohm
4.2.5 DT-9723LIC
The following table explains electrical performance on the Battery Packs (DT-9723LIC,
DT-9723LIC-CN).
Table 4.16
Parameter
Anti-static strength
Malfunction
Destruction
Specification
6 KV (contact) or 8KV (in air)
8 KV (contact) or 15KV (in air)
48
Remark
4.2.6 AD-S10095A
The following table explains electrical performance on the AC Adaptors (AD-S10095AE,
AD-S10095AU).
Table 4.17
Parameter
ESD
RS
EFT
Surge
Specification
Contact : ≥4KV
Non-contact: ≥8KV
Frequency: 80MHz to 1.0GHz
Field strength : 3V/M
1.0 KV on input AC power ports
Line to line : ±1KV (peak)
Line to earth (ground) : ±2 KV (peak)
Remarks
4.2.7 AD-S42120B
The following table explains electrical performance on the AC Adaptors (AD-S42120BE,
AD-S42120BE-CN).
Table 4.18
Parameter
Withstanding noise
Lighting surge
Anti-static strength
(ESD)
Implant noise
Specification
Remark
L-L: 1.0 KV, L-FG: 2.5 KV
8 KV
No damage.
No malfunction and no damage.
L-L, L-FG: 1 KV
No malfunction and no damage.
49
4.3
Mechanical Performance
4.3.1 IT-3100
The following table explains mechanical performance, vibration, and drop impact on the IT-3100
series (all models).
Table 4.19
Parameter
Resistance to vibration
(in package)
Specification
1.5 G or less
Impact durability (in height of fall)
In bare condition
120 cm
In individual carton box
In master carton box
70 cm or less
50 cm or less
-
Condition
10 to 55 Hz
In X, Y and Z directions
Reciprocally for 30 minutes
While the power on the terminal is
being turned on.
Onto concrete surface, one time on each
of the 6 sides and 4 corners.
Onto concrete surface, one time on each
of the 6 sides, 1 corner, and 3 edges.
4.3.2 HA-B30CHG
The following table explains mechanical performance, vibration, and drop impact on the Cradle-type
Battery Charger (HA-B30CHG, HA-B30CHG-CN).
Table 4.20
Parameter
Resistance to vibration
(in package)
Specification
1.5 G or less
Impact durability (in height of fall)
In bare condition
70 cm
In individual carton box
70 cm or less
In master carton box
50 cm or less
50
Condition
-
10 to 55 Hz
In X, Y, and Z directions
Reciprocally for 30 minutes
While powered on (only turn on
display)
One time for 6 faces onto concrete
surface
One time for 6 faces, 1 corner and 3
edges
4.3.3 HA-B61IO
The following table explains mechanical performance, vibration, and drop impact on the Bridge
Satellite Cradle (HA-B61IO, HA-B61IO-CN).
Table 4.21
Parameter
Resistance to vibration
(in package)
Specification
1.5 G or less
Impact durability (in height of fall)
In bare condition
70 cm
In individual carton box
In master carton box
70 cm or less
50 cm or less
Condition
- 10 to 55 Hz
- In X, Y, and Z directions
- Reciprocally for 30 minutes
One time for 6 faces onto concrete
surface
One time for 6 faces, 1 corner and 3
edges
4.3.4 DT-9721CHGE
The following table explains mechanical performance, vibration, and drop impact on the Battery
Charger (DT-9721CHGE, DT-9721CHGE-CN).
Table 4.22
Parameter
Resistance to vibration
Specification
0.75 G
Impact durability (in height of fall)
In bare condition
70 cm
In individual carton box
In master carton box
Condition
- 10 to 55 Hz
- In X, Y, and Z directions
- Reciprocally for 30 minutes
One time for 6 faces onto a piece of
lauan
One time for 6 faces, 1 corner and 3
edges
70 cm
70 cm
51
4.3.5 DT-9723LIC
The following table explains mechanical performance, vibration, and drop impact on the Battery
Packs (DT-9723LIC, DT-9723LIC-CN).
Table 4.23
Parameter
Resistance to vibration
Specification
1.5 G or less
Impact durability (in height of fall)
In bare condition
70 cm or less
In individual carton box
70 cm or less
In master carton box
70 cm or less
Condition
- 10 to 55 Hz
- In X, Y, and Z directions
- Reciprocally for 30 minutes
One time for 6 faces onto P-tile surface.
One time for 6 faces, 1 corner and 3
edges onto concrete surface.
4.3.6 AD-S10095A
The following table explains mechanical performance, vibration, and drop impact on the AC
Adaptor (AD-S10095AE, AD-S10095AU).
Table 4.24
Parameter
Resistance to vibration
Specification
0.5 G or less
Impact durability (in height of fall)
In bare condition
70 cm
In individual carton box
70 cm or less
In master carton box
70 cm or less
52
Condition
- 10 to 100 Hz
- In X, Y, and Z directions
- Reciprocally for 10 minutes
One time for 6 faces onto P-tile surface.
One time for 6 faces, 1 corner and 3
edges onto concrete surface.
4.3.7 AD-S42120B
The following table explains mechanical performance, vibration, and drop impact on the AC
Adaptor (AD-S42120BE, AD-S42120BE-CN).
Table 4.25
Parameter
Resistance to vibration
Specification
0.5 G or less
Impact durability (in height of fall)
In bare condition
70 cm
In individual carton box
70 cm or less
In master carton box
70 cm or less
Condition
- 10 to 100 Hz
- In X, Y, and Z directions
- Reciprocally for 10 minutes
One time for 6 faces onto P-tile surface.
One time for 6 faces, 1 corner and 3
edges onto concrete surface.
4.3.8 HA-B34AT
The following table explains mechanical performance, vibration, and drop impact on the battery
charger car mount unit (HA-B34AT, HA-B34AT-CN).
Table 4.26
Parameter
Resistance to vibration
Specification
3.0 G or less
(See notes 1 and 2.)
Impact durability (in height of fall)
In bare condition
70 cm
(See note 2.)
In individual carton box
70 cm or less
In master carton box
70 cm or less
-
Condition
5 to 200 Hz
In X, Y, and Z directions
Reciprocally for 2 hours
5 to 170 Hz
In Z directions
Reciprocally for 4 hours
One time for 6 faces onto concrete
surface
One time for 6 faces, 1 corner and 3
edges
Notes:
1. When the battery pack and the cover for the battery charger car mount unit are attached to
IT-3100.
2. When IT-3100 is mounted on the cradle-type battery charger.
53
4.3.9 HA-B90DCV
The following table explains mechanical performance, vibration, and drop impact on the screen
protect cover.
Table 4.27
Parameter
Resistance to vibration
Specification
1.5 G or less
(See note.)
Impact durability (in height of fall)
In bare condition
120 cm
(See note.)
In individual carton box
70 cm or less
In master carton box
70 cm or less
Condition
- 10 to 55 Hz
- In X, Y, and Z directions
- Reciprocally for 30 minutes
One time for 6 faces and 4 corner onto
concrete surface
One time for 6 faces, 1 corner and 3
edges onto concrete surface
Note:
HA-B90DCV is attached on IT-3100 for the assessment test.
4.3.10 HA-B93PH
The following table explains mechanical performance, vibration, and drop impact on the formed
sheet paper holder (HA-B93PH, HA-B93PH-CN).
Table 4.28
Parameter
Resistance to vibration
Specification
1.5 G or less
(See note.)
Impact durability (in height of fall)
In bare condition
120 cm
(See Note)
In individual carton box
70 cm or less
In master carton box
70 cm or less
Note:
HA-B93PH is attached on IT-3100 for the assessment test.
54
Condition
- 10 to 55 Hz
- In X, Y, and Z directions
- Reciprocally for 30 minutes
One time for 6 faces and 4 corner onto
concrete surface
One time for 6 faces, 1 corner and 3
edges onto concrete surface
4.3.11 HA-B80AX
The following table explains mechanical performance, vibration, and drop impact on the RS-232C
cross cable (HA-B80AX, HA-B80AX-CN).
Table 4.29
Parameter
Specification
Impact durability (in height of fall)
In individual carton box
70 cm
In master carton box
70 cm
55
Condition
One time for 6 faces, 1 corner, and 3
edges
4.4
Reliability
4.4.1 IT-3100
The following table explains reliability of the main parts on the IT-3100 series (all models).
Table 4.30
Parameter
Backlight
Specification
10,000 hours
MTBF
No. of times of installing and
removing the paper holder to/from
the terminal
No. of times of opening and
closing the paper outlet cover
No. of times of cutting paper with
the cutter on the printer
Printer life
20,000 hours
500 times
Trigger key
1,000,000 times
Other keys
Touch Tapping with the stylus
panel Writing
500,000 times
800,000 times or more
100,000 characters with
Katakana characters
10,000 times
No. of times of mounting and
dismounting the terminal on/from
the cradle
No. of times of connecting and
removing the power jack of AC
Adaptor
No. of times of opening and
closing the power jack cover
No. of times of installing and
removing the battery pack to/from
the battery compartment
No. of times of opening and
closing the battery pack cover
No. of times of installing and
removing an SD memory card
to/from the slot
Remark/Condition
At half-life period in ordinary
temperature
Electronic parts only
5,000 times
15,000 times or greater
50 Km
(paper feeding length)
1,000 times
1,000 times
5,000 times
5,000 times
5,000 times
Continue.
56
In the direction of paper feeding.
With print ratio of 25% (excluding
label papers)
For each R Trigger key and L
Trigger key.
For each key.
With 0.8R polyester stylus with
load of 250 g applied
No. of times of opening and
closing the SD memory card cover
No. of times of installing and
removing a PC card to/from the PC
card slot
No. of times of opening and
closing the PC card slot cover
No. of times of installing and
removing a device to/from the
14-pin serial connector on the
terminal
No. of times of opening and
closing the 14-pin interface cover
No. of times of opening and
closing the 8-pin interface cover
No. of times of reading data on
magnetic card via the MCR
No. of times of installing and
removing the splash protect cover
No. of times of opening and
closing the splash protect cover
No. of times of mounting and
dismounting the neck strap
Strength of the neck strap
Durability of hooks for the hand
strap on the terminal
Strength of the hand strap
Mounting and removing the stylus
to/from the stylus holder
No. of times of installing and
removing the screen protect cover
to/from the terminal
No. of times of opening and
closing the screen protect cover
CMOS imager
5,000 times
5,000 times
5,000 times
5,000 times
5,000 times
5,000 times
200,000 times
500 times
5,000 times
100 times
Tensile strength 15 Kg per 5
seconds
100 times
Tensile strength 15 Kg per 5
seconds
20,000 times
500 times
5,000 times
70,000 hours
57
4.4.2 HA-B30CHG
The following table explains reliability of the main parts on the Cradle-type Battery Charger
(HA-B30CHG, HA-B30CHG-CN).
Table 4.31
Parameter
MTBF for electronics parts
Mounting and removing IT-3100
to/from Cradle
Switch
Power switch
DIP switch
No. of ON/OFF
USB
times of the
RS-232C
connector
RS-422
No. of connecting and removing the
power jack
Specification
50,000 hours
20,000 times
Remark/Condition
5,000 times
10 times
500 times
500 times
100 times
1,500 times
4.4.3 HA-B61IO
The following table explains reliability of the main parts on the Bridge Satellite Cradle (HA-B61IO,
HA-B61IO-CN).
Table 4.32
Parameter
MTBF for electronics parts
Mounting and removing the terminal
to/from the Cradle
Switch
Power switch
DIP switch
Specification
50,000 hours
20,000 times
No. of connecting
and removing the
cable
USB
500 times
RS-232C
500 times
RS-422
100 times
No. of connecting and removing the
AC Adaptor on the power jack
5,000 times
10 times
1,500 times
58
Remark/Condition
Applicable to HA-B61IO and
HA-B61IO-CN.
Applicable to HA-B61IO and
HA-B61IO-CN.
Applicable to HA-B61IO and
HA-B61IO-CN.
Applicable to HA-B61IO and
HA-B61IO-CN.
4.4.4 DT-9721CHGE
The following table explains about reliability on the Battery Charger (DT-9721CHGE,
DT-9721CHGE-CN).
Table 4.33
Parameter
MTBF for electronics parts
Specification
300,000 hours
Remark/Condition
4.4.5 DT-9723LIC
The following table explains reliability on the Battery Packs (DT-9723LIC, DT-9723LIC-CN).
Table 4.34
Parameter
Battery charge-discharge cycle
Specification
90 percent of the capacity at 300 cycles
70 percent of the capacity at 500 cycles
Remark/Condition
- Environment temperature:
23±2 ºC
- Discharge current: 1.1A
constant current
4.4.6 AD-S10095A
The following table explains reliability on the AC Adaptor (AD-S10095AE, AD-S10095AU).
Table 4.35
Parameter
MTBF for electronics parts
Specification
Remark/Condition
50,000 hours
4.4.7 AD-S42120B
The following table explains reliability on the AC Adaptor (AD-S42120BE, AD-S42120BE-CN).
Table 4.36
Parameter
MTBF for electronics parts
Specification
100,000 hours
59
Remark/Condition
4.5
Compliance
4.5.1 IT-3100
The following tables explain compliance with the relevant standards and directive requirements set
mandatory by the respective countries and the region.
Table 4.37
Category
EMC
Laser/ LED
Radio
Type
Approval
(Bluetooth)
Bluetooth
Logo
Safety
RoHS
Standards and
Requirement
FCC part15B
EN55022
EN55024
EN61000-3-2
EN61000-3-3
MIC
GB9254
GB17625.1
CNS13438
AS/NZS CISPR22
FDA CFR21
EN60825
IEC60825
FCC part15C
RSS-GEN
RSS-210
EN300328
EN301489
MIC
SRRC
NCC
Ver. 1.0
UL60950
cUL60950
EN60950-1
AS/NZS4417 or 60950
GB4943
CNS14336
Directive 2002/95/EC
Ministerial Decree No.
39
M53E M54E M55E
M56E
M55U
M56U
Remarks
( -CN) ( -CN) ( -CN)
( -CN)
Yes Yes
-Yes
-Yes
Yes Yes Yes
-Yes
-EMI
Yes Yes Yes
-Yes
-EMS
Yes Yes Yes
-Yes
-High frequency
Yes Yes Yes
-Yes
-Flicker
Yes Yes Yes
-Yes
-Korea
Yes Yes
--Yes
-CCC certification
Yes Yes
--Yes
-Yes Yes
--Yes
-BSMI
Yes Yes Yes
-Yes
-See note.
---Yes
-Yes
--Yes
-Yes
---Yes
-Yes
-Yes Yes
-Yes
-Yes
Yes Yes
-Yes
-Yes Canada
Yes Yes
-Yes
-Yes Canada
Yes Yes Yes
-Yes
-Radio
Yes Yes Yes
-Yes
-EMS
Yes Yes Yes
-Yes
-Korea
Yes Yes
--Yes
-China
Yes Yes
--Yes
-Taiwan
Yes Yes Yes Yes Yes Yes
Yes
-Yes
Yes
Yes
Yes
Yes
Yes
Yes
-Yes
Yes
Yes
Yes
Yes
Yes
--Yes
Yes
--Yes
Yes
Yes; Applicable
Note:
Applicable to AC Adaptor for Australia and New Zealand.
60
Yes
-Yes
------
--Yes
Yes
Yes
Yes
Yes
Yes
Yes
-Yes
------
CCC certification
BSMI
Europe
China
4.5.2 HA-B30CHG
The following table explains compliance with the relevant standards and requirements set mandatory
on the Cradle-type Battery Charger (HA-B30CHG, HA-B30CHG-CN) by the respective countries
and region.
Table 4.38
Category
EMC
Safety
RoHS
Standards/Requirement
FCC Part15B Class B
EN55022
EN55024
GB9254
GB17625.1
UL1950
EN60950
GB4943
EU Directive 2002/95/EC
Ministerial Decree No. 39
Remark
Europe
China
4.5.3 HA-B61IO
The following table explains compliance with the relevant standards and requirements set mandatory
on the Bridge Satellite Cradle (HA-B61IO, HA-B61IO-CN) by the respective countries and region.
Table 4.39
Category
EMC
Safety
RoHS
Standards/Requirement
FCC Part15B Class B
EN55022
EN55024
GB9254
GB17625.1
UL1950
EN60950
GB4943
EU Directive 2002/95/EC
Ministerial Decree No. 39
61
Remark
Europe
China
4.5.4 DT-9721CHGE
The following table explains compliance with the relevant standards and requirements set mandatory
on the Battery Charger (DT-9721CHGE, DT-9721CHGE-CN) by the respective countries and
region.
Table 4.40
Category
EMC
Safety
RoHS
Standards/Requirement
FCC Part15B Class B
EN55022
EN55024
EN61000-3-2
EN61000-3-3
GB9254
GB17625.1
UL1310 CSA C22.2 No. 223 (cUL)
EN60950
GB4943
EU Directive 2002/95/EC
Ministerial Decree No. 39
Remark
Europe
China
4.5.5 DT-9723LIC
The following table explains compliance with the standards and requirements set mandatory on the
Battery Packs (DT-9723LIC, DT-9723LIC-CN) by the respective countries and region.
Table 4.41
Category
EMC
Safety
RoHS
Standards/Requirement
EN61000-3-2
EN61000-3-3
UL1310 CSA C22.2 No. 223 (cUL)
UL60950
EU Directive 2002/95/EC
Ministerial Decree No. 39
62
Remark
USA and Canada
Europe
China
4.5.6 AD-S10095A
The following table explains compliance with relevant standards set mandatory on the AC Adaptors
(AD-S10095AE, AD-S10095AU).
Table 4.42
Category
Standards/Requirement
EMC
EN55022
CISPR22
EN60950
EU Directive 2002/95/EC
Safety
RoHS
Remark
Europe
4.5.7 AD-S42120B
The following table explains compliance with the relevant standards and requirements set mandatory
on the AC Adaptor (AD-S42120BE, AD-S42120BE-CN) by the country and region.
Table 4.43
Category
EMC
Safety
Standards/Requirement
UL60950 3rd edition
CAN/CSA C222 NO.60950-00 1st edition
EN60950
AS/NZS60950
IEC60950
K60950-1
CNS14336
GB4943
CFR47 FCC Part 15 Subpart B
EN55022
EN55024
EN61000-3-2
EN61000-3-3
GB9254
GB17625.1
CNS13438
AZ/NZS CISPR22
63
Remark
CB certificate
4.5.8 HA-B34AT
The following table explains compliance with relevant safety standards and requirement set
mandatory on the battery charger car mount unit (HA-B34AT, HA-B34AT-CN) by the respective
countries and region.
Table 4.44
Category
EMC
Standards/Requirement
ECE Regulation 10.02
64
Remark
5.
5.1
Cable Specifications
DT-888RSC
For Chain Connection in Short Length (1 meter or less)
View form side
Maxmimum
1m
View form top
123456
123456
Cable (See Table 5.1)
Modular plug
compatible with 6 / 6-6 FR SYK
by Sanyo Industrial Co.
Figure 5.1
Table 5.1
Specifications of the cable
Cable
Core wire
Conductor
Insulator
Finish of external shape
Insulator
Finish of external shape
Conductance resistance
Insulation resistance
Sheath
Characteristics
20/0.1A
Semi-hard material P.V.C.
20/0.1A
P.V.C.
Ø4.3±0.1mm
0.12Ω per meter or less
50MΩ or more
Wiring (pin-to-pin straight connection)
Pin no.
Signal
Pin no.
Signal
Cradle at lower
1
IRS+
1
ORS+
Cradle at higher
position under
2
IRS-
2
ORS-
position under
the chain
3
ISD+
3
OSD+
the chain
connection
4
ISD-
4
OSD-
connection
5
ORD+
5
IRD+
6
ORD-
6
IRD-
Figure 5.2
65
For Chain Connection in Long Length (1 meter or longer)
For a cable with its length longer than one meter, no dedicated cable from CASIO is available.
Arrange one locally available that can meet the specifications described below.
View form side
Maxmimum
1,000 m
View form top
123456
123456
Cable compatible with SK-UTP
100M3P by Sanyo Industrial Co.
Modular plug
compatible with 6 / 6-6 FR SYK
50 by Sanyo Industrial Co.
Figure 5.3
Wiring (pin-to-pin straight/twist-pair connection)
Pin no.
Signal
Pin no.
Signal
Cradle at lower
1
IRS+
1
ORS+
Cradle at higher
position under
2
IRS-
2
ORS-
position under
the chain
3
ISD+
3
OSD+
the chain
connection
4
ISD-
4
OSD-
connection
5
ORD+
5
IRD+
6
ORD-
6
IRD-
Figure 5.4
66
5.2
DT-887AXA
The dedicated RS-232C cross cable (DT-887AXA, DT-887AXA-CN) is available for connecting the
terminal to a PC via the 9-pin serial interface on the HA-B61IO (Bridge Satellite Cradle). See the
specifications below.
Length; 1.5 m
Wiring
Cradle side
Pin no.
Signal
Pin no.
Signal
1
CD
1
CD
2
RD
2
RD
3
SD
3
SD
4
ER
4
ER
5
SG
5
SG
6
DR
6
DR
7
RS
7
RS
8
CS
8
CS
9
CI
9
CI
Figure 5.5
67
Other device side
5.3
HA-B80AX
The dedicated RS-232C cross cable (HA-B80AX, HA-B80AX-CN) is available for directly
connecting the terminal to a PC via the 8-pin serial interface on the terminal. See the specifications
below.
Length; 1.5 m
Wiring
Pin no.
Signal
Pin no.
Signal
1
SD
1
CD
2
RD
2
RD
3
RS
3
SD
4
CS
4
ER
5
Vcc
5
GND
6
GND
6
DR
7
ER
7
RS
8
DR
8
CS
9
CI
Figure 5.6
68
6.
6.1
Precautions
Handling Precautions
Precautions for short-term storage (1 to 2 days)
• If the IT-3100 remains unused for a long period including Saturday and Sunday, before starting
holiday replace the battery pack if installed in the terminal with a fully charged battery pack. This
will conserve the built-in memory backup battery and ensure retention of data on the terminal.
• If there is a possibility of the above or operator error (e.g., a fully charged battery has not been
inserted), practice system operation that maintains a backup to avoid loss of data due to
consumption of the batteries.
Precautions for long-term storage (over one week)
• Prior to a long-term storage (over one week), always back-up data in the terminal to other
memory storage device. In addition, remove the lithium-ion battery pack before storage. This can
minimize overly discharging the installed battery and minimize consumption of the memory
backup battery.
• Do not store the removed battery pack at high temperature. Otherwise, it will discharge at an
accelerated rate. Note that the capacity after the battery if it is not used for 10 days at 60°C will be
65%, and that after 20 days at 60°C will be 55%.
Battery Pack
• Never contact the “+” and “-“ terminals with metal objects such as a wire. Also, do not carry and
store the battery with a metal necklace or hair pin. Otherwise, the battery pack may be
short-circuited resulting in an excessive current and causing the battery to become hot, smoke,
explode or catch fire.
• Neither dispose of the battery pack into a fire nor heat it. The insulation may be burnt, the gas
exhaust valve or safety mechanism may be damaged, or the internal electrolyte may ignite
causing the battery pack to become hot, generate smoke, explode, or ignite.
• Neither leave nor use the battery pack in a place with a high temperature (over 80°C) or close to a
fire or hot stove. Should the resin separator be damaged due to excessive heat, the battery pack
may be short-circuited causing it to become hot, generate smoke, explode, or ignite.
• Do not soak the battery pack in fresh water or sea water. If the protection means incorporated in
the battery pack is damaged, the battery pack may become hot, smoke, explode, or ignite.
• Do not attempt to charge the battery close to a fire, in direct sunlight, or in a car parked in the sun.
A heated battery pack will trigger the internal hazard protection means to stop the charging
function. Or, the protection means may be damaged and the battery may be charged with an
excessive current or voltage, or have abnormal chemical reactions induced to cause it to become
hot, smoke, explode, or ignite.
• Do not stick a pin or nail in the battery pack. Neither hit it with a hammer nor stamp it. If this is
done, the battery pack may be broken or deformed resulting in a short circuit and causing it to
become hot, smoke, explode, or ignite.
• Do not hit or throw the battery pack. If the protection means incorporated in the battery pack is
damaged, the battery pack may be charged with an excessive current or voltage, or have abnormal
chemical reactions induced to cause it to become hot, smoke, explode, or ignite.
• Never use a battery pack that is significantly damaged or deformed. It may become hot, smoke,
explode, or ignite.
69
• Do not attempt to solder anything directly on the battery pack surface. The insulation may be
damaged or the gas exhaust valve or safety mechanism may be damaged, causing the battery pack
to become hot, smoke, explode, or ignite.
• Do not use the battery pack in other device than the terminal. The performance or service life of
the battery pack may be reduced or abnormal current may flow to cause it to become hot, smoke,
explode, or ignite.
• When charging the battery pack use only dedicated cradles or dedicated battery charger and its
AC adaptor available from CASIO, at a temperature between 0°C and 40°C. If the battery pack is
charged with battery chargers other than those specified by CASIO, it may be over-charged,
charged with an excessive current, or have abnormal chemical reactions induced, causing it to
become hot, smoke, explode, or ignite.
• The battery pack has a specific polarity. Do not force it into the IT-3100. Check the polarity. If
the battery pack is connected backwards, it can be incorrectly charged and have an abnormal
chemical reaction induced, causing it to become hot, smoke, explode, or ignite.
• If the internal electrolyte of the battery pack leaks and enters the eye, do not rub the eye. Rinse the
eye with a sufficient amount of clean water, such as tap water, then immediately consult with a
doctor. The electrolyte can cause eye damage.
70