Alto X23 User`s manual

User's Manual
X23
2-WAY STEREO/3-WAY MONO
ACTIVE CROSSOVER
R
LTO
www.altoproaudio.com
Version 2.0 Dec. 2002
English
the recommended fuse type as indicated in this
manual. Do not short-circuit the fuse holder. Before
replacing the fuse, make sure that the product is
OFF and disconnected from the AC outlet.
SAFETY RELATED SYMBOLS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Protective Ground
This symbol, wherever used, alerts you to the presence of un-insulated and dangerous voltages within the product enclosure. These are voltages that
may be sufficient to constitute the risk of electric
shock or death.
Before turning the product ON, make sure that it is
connected to Ground. This is to prevent the risk of
electric shock.
Never cut internal or external Ground wires. Likewise,
never remove Ground wiring from the Protective
Ground Terminal.
This symbol, wherever used, alerts you to important operating and maintenance instructions.
Please read.
Operating Conditions
Always install in accordance with the manufacturer's
instructions.
Protective Ground Terminal
Denotes the product is turned on.
To avoid the risk of electric shock and damage, do
not subject this product to any liquid/rain or moisture.
Do not use this product when in close proximity to
water.
OFF: Denotes the product is turned off.
Do not install this product near any direct heat source.
WARNING
Do not block areas of ventilation. Failure to do so
could result in fire.
AC mains (Alternating Current)
Hazardous Live Terminal
ON:
Describes precautions that should be observed to
prevent the possibility of death or injury to the user.
Keep product away from naked flames.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
Read these instructions
Describes precautions that should be observed to
prevent damage to the product.
Follow all instructions
Keep these instructions. Do not discard.
WARNING
Heed all warnings.
Power Supply
Only use attachments/accessories specified by the
manufacturer.
Ensure that the mains source voltage (AC outlet)
matches the voltage rating of the product. Failure
to do so could result in damage to the product and
possibly the user.
Power Cord and Plug
Do not tamper with the power cord or plug. These are
designed for your safety.
Unplug the product before electrical storms occur
and when unused for long periods of time to reduce
the risk of electric shock or fire.
Do not remove Ground connections!
If the plug does not fit your AC outlet seek advice from
a qualified electrician.
External Connection
Always use proper ready-made insulated mains
cabling (power cord). Failure to do so could result
in shock/death or fire. If in doubt, seek advice from
a registered electrician.
Protect the power cord and plug from any physical
stress to avoid risk of electric shock.
Do Not Remove Any Covers
Cleaning
Within the product are areas where high voltages
may present. To reduce the risk of electric shock do
not remove any covers unless the AC mains power
cord is removed.
When required, either blow off dust from the product
or use a dry cloth.
Do not place heavy objects on the power cord. This
could cause electric shock or fire.
Do not use any solvents such as Benzol or Alcohol.
For safety, keep product clean and free from dust.
Covers should be removed by qualified service
personnel only.
Servicing
Refer all servicing to qualified service personnel only.
No user serviceable parts inside.
Do not perform any servicing other than those instructions contained within the User's Manual.
Fuse
To prevent fire and damage to the product, use only
1
PREFACE
Dear Customer:
Thanks for choosing
job and researches.
LTO Active Crossover and thanks for choosing the one of results of
LTO AUDIO TEAM
For our LTO AUDIO TEAM, music and sound are more than a job...are first of all passion and et us say...our
obsession!
We have been designing professional audio products for a long time in cooperation with some of the major brands in
the world in the audio field.
The LTO line presents unparalleled analogue and digital products made by Musicians for Musicians in our R&D
Centres in Italy, Netherlands, United Kingdom and Taiwan. The core of our digital audio products is a sophisticated
DSP (Digital sound processor) and a large range of state of the art algorithms which have been developed by our
Software Team for the last 7 years.
Because we are convinced you are the most important member of LTO AUDIO TEAM and the one confirming
the quality of our job, we'd like to share with you our work and our dreams, pay attention to your suggestions and
your comments.
Following this idea we create our products and we will create the new ones! From our side, we guarantee you and
we will guarantee you also in future the best quality, the best fruits of our continuous researches and the best prices.
Our LTO Active Crossover is the result of many hours of listening and tests involving common people, area experts,
musicians and technicians.
The results of this effort is an efficient and effective electronic crossover solution, which will give you precise control
and superior sound from your loudspeaker system.
Nothing else to add, but that we would like to thank all the people that made the LTO Active Crossover a reality
available to our customers, and thank our designers and all the LTO staff, there to make possible the realization
of products containing our idea of music and sound and there to support you, our customers, in the best way, conscious
that you are our best richness.
Thank you very much.
LTO AUDIO TEAM
2
TABLE OF CONTENTS
1. INTRODUCTION .................................................................................................................................4
2. FEATURE LIST ...................................................................................................................................4
3. CONTROL ELEMENTS.......................................................................................................................4
3.1 The Front Panel
3.2 The Rear Panel
4. INSTALLATION & CONNECTION .....................................................................................................7
4.1 Mains Connection
4.2 Audio Connection
4.3 Rack Mounting
5. APPLICATION.....................................................................................................................................8
5.1 X23 2-Way Stereo
5.2 X23 3-Way Mono
6. TECHNICAL SPECIFICATIONS........................................................................................................10
7. WARRANTY ......................................................................................................................................11
3
1. INTRODUCTION
First we give our sincere appreciation for your confidence in LTO products by purchasing our X23 Active Crossover.
It is the most effective support to us. The X23 Active Crossover is an ideal crossover and used universally in most small
and large PA systems, recording studio monitors, DJ setups, commercial installations and live concerts. It is not only
adaptable in mounting to different sound systems, but also it has many developed features. For example, Clip LED Indicators, Mute switches for all frequencies output, CD Boost and Phase Inversion.
The X23 Active Crossover is a single rack unit, dual channels electronic crossover, which is able to operate as the 2way stereo and 3-way mono speaker systems.
2. FEATURE LIST
Single rack unit (1U)
Clip LED indicators
Mute switches used to mute the output signal of each frequencies range
XLR balanced and 1/4" TRS connectors for inputs and outputs
Phase inversion compensates for corresponding frequencies cancellation in some field
CD Boost compensates power loss during the long distance transmission
Superior-quality parts and rigid configuration for long life and full credibility
Excellent audio performance and low noise interference
3. CONTROL ELEMENTS
3.1 The Front Panel
CLIP
CLIP
LOW
HIGH
LOW
HIGH
CHANNEL 1
CHANNEL 2
170
0
0
0
300
0
0
170
300
X23
0
R
LTO
90
OFF
+6
INPUT LEVEL
(INPUT LEVEL)
2 3
90
700
1
10
+6
OFF
MUTE
4
80
1K
RANGE
XOVER FREQ
(XOVER FREQ)
LOW GAIN
(LOW GAIN)
5
6
+6
OFF
MUTE
OFF
7
8
+6
INPUT LEVEL
HIGH GAIN
10 11
9
+6
OFF
ON
1
10
MUTE
80
1K
RANGE
XOVER FREQ
(XOVER FREQ)
LOW GAIN
(MID GAIN)
12
700
13
14
OFF
+6
15
16
OFF
MUTE
2W- STEREO
(3W- MONO) POWER
HIGH GAIN
(HIGH GAIN)
17
1
X23 2-way stereo / 3-way mono active crossover
2-WAY STEREO MODE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
3-WAY MONO MODE
Power Switch
Input Level
LOW, MID Clip LED
LOW Gain
LOW Mute
LOW-MID Crossover Frequency
80Hz-1KHz (Range 1)
LOW-MID Crossover Range
(not used)
(not used)
(not used)
(Ignored), HIGH Clip LED
MID Gain
MID Mute
MID-HIGH Crossover Frequency
800Hz-10KHz (Range 10)
Ch1 Input Level
Ch1 LOW, Ch1 HIGH Clip LEDs
Ch1 LOW Gain
Ch1 LOW Mute
Ch1 LOW-HIGH Crossover Frequency
800Hz-10KHz (Range 10)
Ch1 LOW-HIGH Crossover Range
Ch1 HIGH Gain
Ch1 HIGH Mute
Ch2 Input Level
Ch2 LOW, Ch2 HIGH Clip LEDs
Ch2 LOW Gain
Ch2 LOW Mute
Ch2 LOW-HIGH Crossover Frequency
800Hz-10KHz (Range 10)
4
2-WAY STEREO
3-WAY MONO
ACTIVE CROSSOVER
15
Ch2 LOW-HIGH Crossover Range
MID-HIGH Crossover Range
16
Ch2 HIGH Gain
HIGH Gain
17
Ch2 HIGH Mute
HIGH Mute
Power switch
Turn the power on or off.
Clip LED
It means that some band has resulted in clipping distortion when the LED is glittering. It is regarded as normal
if it is glittering only one or two times. But if it lasts for a long time, you should reduce the input signal to avoid
audio distortion.
Mute switch
These buttons are used to mute each kind of frequencies outputs.
3.2 The Rear Panel
18
AC INPUT
PUSH
PUSH
110-120V
95-120V /210-240V 60-50Hz
Rated Power Consumption 8.5W
220-240V
STEREO MONO
FUSE:
210-240V: T100mAL 250VAC
95-120V: 200mA 250VAC
REPLACE FUSE WITH CORRECT
TYPE ONLY
NEW
CD
BOOST MODE
HIGH
PHASE
NEW
TIDE
CD
BOOST
HIGH
PHASE
3
2
1
TIDE
3
2
1
Apparaten skall anslutas till
Jordat uttag nar den ansluts
Till ett natverk
A101
2WAY- STEREO
/ (3WAY- MONO)
19
HIGH OUT 2 / (HIGH OUT)
LOW OUT 2 / (MID OUT)
INPUT 2 / (NOT USED)
HIGH OUT 1 / (NOT USED)
LOW OUT1 / (LOW OUT)
CHANNEL 2
30
29
28
INPUT 1 / (INPUT)
CHANNEL 1
27 26
24
25
23
22
21
20
X23 2-way stereo / 3-way mono active crossover
2-WAY STEREO MODE
3-WAY MONO MODE
18
Fuse Holder
19
AC Inlet
20
Ch1 Line Input (Linked XLR-F&jack)
Line Input (Linked XLR-F&jack)
21
Ch1 Constant Directivity Boost
Constant Directivity Boost
22
Ch1 LOW Output (Linked XLR-M&jack)
Low Output (Linked XLR-M&jack)
23
Ch1 HIGH Phase Inversion
MID Phase Inversion
24
Ch1 HIGH Output (Linked XLR-M&jack)
(not used)
25
Ch2 Line Input (Linked XLR-F&jack)
(not used)
Stereo / Mono Mode
26
27
Ch2 Constant Directivity Boost
(not used)
28
Ch2 LOW Output (Linked XLR-M&jack)
MID Output (Linked XLR-M&jack)
29
Ch2 HIGH Phase Inversion
HIGH Phase Inversion
30
Ch2 HIGH Output (Linked XLR-M&jack)
HIGH Output (Linked XLR-M&jack)
5
Fuse holder & voltage selector
Your unit may have the AC voltage selector ( 115V/60Hz or
pull fuse-holder out and rotate 180 , then push in again.
230V/50Hz) built into the Fuse Holder. To change,
Caution: The fuse protecting the AC supplies circuits of this unit. The fuse can only be changed by a qualified
technician, in the event of a fault or changing the supply voltage. If the fuse continues to blow after replacing,
discontinue use of this unit before repaired.
220-240V
110-120V
220-240V
110-120V
THIS IS SET FOR
220V AC TO 240V
AC OPERATION
THIS IS SET FOR
110V AC TO 120V
AC OPERATION
The fuse-holder above the AC connector on the rear of the chassis has 3 triangular markers (please refer to the
above pictures), with two of these triangles opposing each other, your unit is set to the operating Voltage printed
next to these markers.
AC Inlet
Please don't plug power cord into unit and AC power if voltage has not been correctly set.
Inputs & Outputs
The inputs and outputs can be used as balanced and unbalanced XLR and 1/4" TRS connectors, they can be used
to input and output signals.
CD Boost
Abbreviation for 'Constant Directivity Boost', this button can be used to boost the high frequencies by +3dB at
3.5kHz, then +6dB per octave till 22.5kHz.
Through this function and using with the horns, power loss of the high frequencies can be compensated for during
the long distance transmission in the large PA reinforcement systems.
Phase inversion
This button will reverse the phase of the corresponding frequencies output by 180 , so that, the frequencies
cancellation in some fields can be compensated for.
Mode switch
It can set the operational mode of this unit. You are able to operate it as a 3-way mono crossover (High/Mid/Low)
when it is pressed. On the contrary, you are able to operate it as 2-way stereo crossover (High/Low) when it is
released.
6
4. INSTALLATION & CONNECTION
4.1 Mains Connection
Please ensure that the LTO X23 Active Crossover is set to the correct supply voltage before plugging the power
cord into the wall outlet, use the same fuse as marked on the fuse holder at the AC power connection socket.
The mains connection of the LTO X23 Active Crossover is made by using the enclosed mains cord and a
standard IEC receptacle. It meets all of the international safety certification requirements.
4.2 Audio Connection
The LTO X23 Active Crossover presents with balanced XLR and 1/4" TRS connectors, and it can be interfaced
by several ways to support a variety of applications without any signal loss.
a. Wiring Configuration
Either the 1/4" TRS (Tip-Ring-Sleeve) jack or the XLR servo connector can be wired in balanced and unbalanced
modes. Please wire your systems as the following examples:
For 1/4" Phone jack
+
+
-
Tip
+
Tip
Ring
Tip
Ring
Sleeve
Sleeve
TS Type Unbalanced
Sleeve
TRS Type Balanced
TRS Type Unbalanced
For XLR connector
Pin2 (+)
Pin2 (+)
Pin3 (-)
Pin3 (-)
(Linked to Pin1 manually,
)
Pin1 ( )
Pin1 ( )
XLR Type Unbalanced
XLR Type Balanced
b. In Line Connection
For these applications, the X23 Active Crossover provides XLR connectors to easily interface with most professional audio devices. Follow the configuration examples below for your particular connection.
Balanced
TIP RING SLEEVE
SLEEVE RING TIP
3
2
2
3
1
1
1
3
2
TIP RING SLEEVE
Tip
Ring
Sleeve
1
2
1
2
3
3
Tip
Ring
1
2
3
Sleeve
7
Tip
Ring
Sleeve
Unbalanced
1
Tip
Ring
3
2
1
2
3
Sleeve
TIP RING SLEEVE
Tip
1
1
2
3
3
2
Sleeve
1
TIP SLEEVE
2
3
1
2
3
Cent r e
Screen
Tip
TIP SLEEVE
Tip
Sleeve
SLEEVE TIP
Sleeve
Tip
Ring
TIP RING SLEEVE
SLEEVE RING TIP
Tip
Ring
Sleeve
Sleeve
Tip
Cent r e
Sleeve
Screen
Tip
Ring
Centre
Sleeve
Screen
TIP SLEEVE
TIP RING SLEEVE
3
3
1
1
1
2
2
2
1
2
3
3
4.3 Rack Mounting
The most secure mounting is on a universal rack shelf available from various rack manufactures or your music dealer.
The X23 Active Crossover fits into one standard 19" rack unit of space. Please allow at least an additional 4" depth for the
connectors on the rear panel. Be sure that there is enough air space around the unit for sufficient ventilation and please
do not place the X23 Active Crossover on high temperature devices such as power amplifiers etc. to avoid overheating.
5. APPLICATION
5.1 X23 2-Way Stereo
To get such a typical application, configure your system and connect the wires in the following proper steps:
1.Release the mode switch to enter into the 2-way stereo mode.
2.Apply the stereo program sources from the Mixer to the Input Connectors of Channel1 and Channel2.
3.Output the Low frequencies signal to the power amplifier.
4.Output the High frequencies signal to the power amplifier.
5.Set LOW-HIGH Crossover Range of channel1 and channel2 to 10.
6.Power up the X23 first, then the power amplifier to run the system. While powered off, please ensure the power
amplifier is turned off first, then the X23.
HIGH
HIGH
LOW
LOW
AC INPUT
STEREO MONO
FUSE:
110-120V
210-240V: T100mAL 250VAC
95-120V: 200mA 250VAC
REPLACE FUSE WITH CORRECT
TYPE ONLY
A101
PUSH
PUSH
95-120V /210-240V 60-50Hz
Rated Power Consumption 8.5W
220-240V
NEW
CD
BOOST MODE
HIGH
PHASE
NEW
TIDE
HIGH
PHASE
3
2
1
CD
BOOST
TIDE
3
2
1
Apparaten skall anslutas till
Jordat uttag nar den ansluts
Till ett natverk
2WAY- STEREO
/ (3WAY- MONO)
HIGH OUT 2 / (HIGH OUT)
LOW OUT 2 / (MID OUT)
INPUT 2 / (NOT USED)
HIGH OUT 1 / (NOT USED)
CHANNEL 2
LOW OUT1 / (LOW OUT)
CHANNEL 1
8
INPUT 1 / (INPUT)
5.2 X23 3-Way Mono
To get such a typical application, configure your system and connect the wires in the following proper steps:
1.Press the mode switch to enter into the 3-way mono mode.
2.Apply the mono program sources from the Mixer to the input connector of channel1.
3.Output the Low frequencies signal to the power amplifier.
4.Output the Mid frequencies signal to the power amplifier.
5.Output the High frequencies signal to the power amplifier.
6.Power up the X23 first, then the power amplifier to run the system. While powered off, please ensure the power
amplifier is turned off first, then the X23.
HIGH
LOW
MID
AC INPUT
STEREO MONO
FUSE:
110-120V
210-240V: T100mAL 250VAC
95-120V: 200mA 250VAC
REPLACE FUSE WITH CORRECT
TYPE ONLY
A101
PUSH
PUSH
95-120V /210-240V 60-50Hz
Rated Power Consumption 8.5W
220-240V
NEW
CD
BOOST MODE
HIGH
PHASE
NEW
TIDE
HIGH
PHASE
3
2
1
CD
BOOST
TIDE
3
2
1
Apparaten skall anslutas till
Jordat uttag nar den ansluts
Till ett natverk
2WAY- STEREO
/ (3WAY- MONO)
HIGH OUT 2 / (HIGH OUT)
LOW OUT 2 / (MID OUT)
INPUT 2 / (NOT USED)
CHANNEL 2
HIGH OUT 1 / (NOT USED)
LOW OUT1 / (LOW OUT)
CHANNEL 1
9
INPUT 1 / (INPUT)
6. TECHNICAL SPECIFICATIONS
Electrical
LOW-MID Frequency Range
Range 1 80Hz - 1KHz
MID-HIGH Frequency Range
Range 10 800Hz - 10KHz
HUM & Noise
LOW Section (Output@0dB)
AV=0dB, fc=800Hz
-106dBu
HIGH Section(Output @0dB)
-97dBu
S/N Ratio
118dB
Input Level
continuously variable
Output Level
CD Boost
low, high continuously variable
rear panel switch
Mute
low, high front panel switches
Phase
rear panel switch
Connector type
3-pole IEC, grounded
Type
Servo controlled, stabilized
Mains supply
95-120V /210-240V , 60-50Hz
Power Rating
8.5W
Dimensions
483(W) 194.5(D) 44(H)mm (19" 7.7" 1.7")
Weight
3.1Kg (6.84lb)
Controls
Power Supply
Physical
10
7. WARRANTY
1. WARRANTY REGISTRATION CARD
To obtain Warranty Service, the buyer should first fill out and return the enclosed Warranty Registration Card within
10 days of the Purchase Date.
All the information presented in this Warranty Registration Card gives the manufacturer a better understanding of
the sales status, so as to purport a more effective and efficient after-sales warranty service.
Please fill out all the information carefully and genuinely, miswriting or absence of this card will void your warranty
service.
2. RETURN NOTICE
2.1 In case of return for any warranty service, please make sure that the product is well packed in its original shipping
carton, and it can protect your unit from any other extra damage.
2.2 Please provide a copy of your sales receipt or other proof of purchase with the returned machine, and give detail
information about your return address and contact telephone number.
2.3 A brief description of the defect will be appreciated.
2.4 Please prepay all the costs involved in the return shipping, handling and insurance.
3. TERMS AND CONDITIONS
3.1
LTO warrants that this product will be free from any defects in materials and/or workmanship for a period
of 1 year from the purchase date if you have completed the Warranty Registration Card in time.
3.2 The warranty service is only available to the original consumer, who purchased this product directly from the
retail dealer, and it can not be transferred.
3.3 During the warranty service, LTO may repair or replace this product at its own option at no charge to you for
parts or for labor in accordance with the right side of this limited warranty.
3.4 This warranty does not apply to the damages to this product that occurred as the following conditions:
Instead of operating in accordance with the user's manual thoroughly, any abuse or misuse of this product.
Normal tear and wear.
The product has been altered or modified in any way.
Damage which may have been caused either directly or indirectly by another product / force / etc.
Abnormal service or repairing by anyone other than the qualified personnel or technician.
And in such cases, all the expenses will be charged to the buyer.
3.5 In no event shall LTO be liable for any incidental or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you.
3.6 This warranty gives you the specific rights, and these rights are compatible with the state laws, you may also
have other statutory rights that may vary from state to state.
11
SEIKAKU TECHNICAL GROUP LIMITED
No. 1, Lane 17, Sec. 2, Han Shi W. Road, Taichung, 401 Taiwan
http://www.altomobile.com Tel: 886-4-22313737
email: info@altomobile.com Fax: 886-4-22346757
All rights reserved to ALTO Mobile. Due to continued development in response to
customer feedback, product features, specifications and/or internal/external design may be
changed without prior notice. No photocopying, translation or reproduction of any part of this user
manual is allowed without prior written permission.Copyright c 2004 Seikaku Technical Group Limited.
NF00878-1.0