YAESU VX-3R Operating Manual

VHF/UHF

ULTRA-COMPACT DUAL-BAND TRANSCEIVER

WITH WIDE BAND COVERAGE

VX-3R

O

PERATING

M

ANUAL

VERTEX STANDARD CO., LTD.

4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan

VERTEX STANDARD

US Headquarters

10900 Walker Street, Cypress, CA 90630, U.S.A.

YAESU EUROPE B.V.

P.O. Box 75525, 1118 ZN Schiphol, The Netherlands

YAESU UK LTD.

Unit 12, Sun Valley Business Park, Winnall Close

Winchester, Hampshire, SO23 0LB, U.K.

VERTEX STANDARD HK LTD.

Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,

Kwun Tong, Kowloon, Hong Kong

VERTEX STANDARD (AUSTRALIA) PTY., LTD.

Normanby Business Park, Unit 14/45 Normanby Road

Notting Hill 3168, Victoria, Australia

General Description ................................................................. 1

Controls & Connections ........................................................... 2

Keypad Functions ................................................................. 3

LCD Display ......................................................................... 4

Accessories & Options ............................................................. 5

Installation of Accessories ........................................................ 6

Antenna Installation .............................................................. 6

Installation of FNB-82LI Battery Pack ................................. 6

Battery Charging ................................................................... 7

Installation of FBA-37 Alkaline Battery Case ...................... 8

Battery Life Information ....................................................... 8

Interface of Packet TNCs ........................................................ 9

Operation ................................................................................ 10

Switching Power On and Off .............................................. 10

Adjusting the Volume Level ............................................... 10

Squelch Adjustment ............................................................ 11

Selecting the Operating Band ............................................. 12

Frequency Navigation ......................................................... 13

Transmission ....................................................................... 14

AM and FM Broadcast Reception ...................................... 15

SUB-RX Operation ....................................................... 16

Advanced Operation .............................................................. 18

Keyboard Locking .............................................................. 18

Adjusting the Keypad Beeper Volume Level ...................... 19

Keypad/LCD Illumination .................................................. 20

Checking the Battery Voltage ............................................. 20

Changing the Channel Steps ............................................... 21

Changing the Receiving Mode ............................................ 21

S-meter Squelch .................................................................. 22

Checking the Temperature .................................................. 23

Repeater Operation ................................................................ 24

Repeater Shifts .................................................................... 24

Automatic Repeater Shift (ARS) ......................................... 24

Manual Repeater Shift Activation ....................................... 25

Changing the Default Repeater Shifts ............................ 25

Checking the Repeater Uplink (Input) Frequency ............... 26

CTCSS/DCS/EPCS Operation .............................................. 28

CTCSS Operation ............................................................... 28

DCS Operation ................................................................... 30

DCS Code Inversion ...................................................... 31

Tone Search Scanning ........................................................ 32

EPCS (Enhanced Paging & Code Squelch) ........................ 34

Storing the CTCSS Tone Pairs for EPCS Operation ...... 34

Activating the Enhanced Paging &

Code Squelch System .................................................... 35

Paging Answer Back ...................................................... 36

CTCSS/DCS/EPCS Bell Operation .................................... 37

Programming the User Beep .......................................... 38

Split Tone Operation .......................................................... 39

Tone Calling (1750 Hz) ...................................................... 40

Memory Mode ........................................................................ 42

Regular Memory Channel Operation .................................. 42

Memory Storage ............................................................ 42

Storing Independent Transmit Frequencies

(“Odd Split”) ............................................................ 43

Memory Recall .............................................................. 43

HOME Channel Memory .............................................. 44

Home Channel Recall ............................................... 44

Home Channel Frequency Change ........................... 44

Labeling Memories ........................................................ 45

Memory Offset Tuning .................................................. 46

Masking Memories ........................................................ 47

Memory Bank Operation ............................................... 48

Assigning Memories to a Memory Bank .................. 49

Memory Bank Recall ................................................ 48

Removing Memories from a Memory Bank ............. 49

Changing a Memory Bank’s Name ........................... 49

Moving Memory Data to the VFO ................................ 50

Memory Only Mode ...................................................... 50

Special Memory Channel Operation ................................... 51

Weather Broadcast Channels ......................................... 51

VHF Marine Channels ................................................... 52

Short-wave Broadcast Station Memory Channels .......... 53

Contents

Scanning .................................................................................. 54

Setting the Scan-Resume Mode .......................................... 54

VFO Scanning .................................................................... 56

How to Skip (Omit) a Frequency during VFO Scan ........................................................... 57

Setting the Squelch Level during active Scanning Operation .................................. 57

Memory Scanning ............................................................... 58

How to Skip (Omit) a Channel during Memory Scan Operation .................................... 59

Preferential Memory Scan ............................................. 60

Memory Bank Scan ....................................................... 61

Programmable (Band Limit) Memory Scan (PMS) ............. 62

Priority Channel Scanning (Dual Watch) ........................... 63

Priority Revert Mode ..................................................... 64

Automatic Lamp Illumination on Scan Stop ....................... 65

Band Edge Beeper .............................................................. 65

Smart Search Operation ........................................................ 66

Setting the Smart Search Mode ........................................... 66

Storing Smart Search Memories ......................................... 67

Channel Counter Operation .................................................. 68

Setting the Channel Counter Sweep Width ......................... 69

Message Feature ..................................................................... 70

Programming a Message ..................................................... 70

Programming a Member List .............................................. 71

Set Your Personal ID .......................................................... 72

Sending a Messages ............................................................ 72

Receiving a Message .......................................................... 73

Emergency Feature ................................................................ 74

Emergency Channel Operation ........................................... 74

Emergency Automatic ID (EAI) Feature ............................ 75

Selecting the EAI mode and its Transmit Time ............. 76

Activating the EAI feature ............................................. 76

To Locate an Unresponsive Operator

ARTS

Using the EAI feature .................................................... 77

TM (Automatic Range Transponder System) .............. 78

Basic ARTS Setup and Operation ....................................... 79

ARTS Polling Time Options ............................................... 79

ARTS Alert Beep Options .................................................. 80

CW Identifier Setup ............................................................ 81

Internet Connection Feature ................................................. 82

SRG (“Sister Radio Group”) mode ..................................... 82

FRG (“Friendly Radio Group”) mode ................................ 83

Programming the FRG code .......................................... 83

Operation (Accessing an FRG Node) ............................ 84

DTMF Operation ................................................................... 85

Manual DTMF Tone Generation ........................................ 85

DTMF Autodialer ............................................................... 85

CW Learning Feature ............................................................ 88

CW Training Feature ............................................................ 90

Miscellaneous Setting ............................................................. 91

Password ............................................................................. 91

Programming the [ ] Key ................................................. 91

Assign the Set Mode Item to the [ ] Key .................... 91

ATT (Front End Attenuator) ............................................... 93

Receive Battery Saver Setup ............................................... 93

Wakeup Feature .................................................................. 94

TX Battery Saver ................................................................ 95

Disabling the BUSY Indicator ............................................ 95

Automatic Power-Off (APO) Feature ................................. 96

Transmitter Time-Out Timer (TOT) ................................... 97

Automatic Power-On Feature ............................................. 98

Busy Channel Lock-Out (BCLO) ....................................... 98

Changing the TX Deviation Level ...................................... 99

Changing the Microphone Gain .......................................... 99

My Bands Operation ......................................................... 100

Changing the Status of the [VOL] Key ............................. 101

Cloning .................................................................................. 102

Set (Menu) Mode .................................................................. 103

Specifications ........................................................................ 126

Reset Procedures .................................................................. 128

G

ENERAL

D

ESCRIPTION

The VX-3R is a micro-miniature multiband FM transceiver with extensive receive frequency coverage, providing local-area two-way amateur communications along with unmatched monitoring capability.

The VX-3R’s incredibly small size allows you to take it anywhere - hiking, skiing, or while walking around town - and its operating flexibility brings the user many avenues of operating enjoyment. Its incredibly tiny FNB-82LI Lithium-Ion Battery Pack provides up to 1.5

Watts of transmit power on VHF, and 1 Watt on UHF. In addition to the 144- and 430-MHz transceiver operation, the VX-3R provides receive coverage of the AM (MF) broadcast band, with the internal bar antenna, the FM broadcast bands, HF Shortwave Bands, VHF and UHF TV bands, the VHF AM aircraft band, and a wide range of commercial and public safety frequencies! The VX-3R internal antenna bar provides good AM broadcast receive capabilities without having to use an external antenna.

Additional features include an Enhanced Paging and Code Squelch (EPCS), which allows you to page a particular station and only receive calls from that station. A security Password may be set, which will allow you to turn on and operate your transceiver only after you enter your Password. A convenient key provides access to Vertex Standard’s WIRES™

(Wide-Coverage Internet Repeater Enhancement System). The Emergency Automatic ID

(EAI) function can automatically cause your VX-3R to transmit your callsign and engage your rig’s microphone, even if you are disabled and unable to press the PTT switch. Features include: transmit Time-Out Timer (TOT), Automatic Power-Off (APO), and Automatic Repeater Shift (ARS). Yaesu’s exclusive ARTS™ (Auto-Range Transponder System) which “beeps” the user when you move out of communications range with another

ARTS™ equipped station. There is provision to reduce the TX deviation for use in areas of high channel congestion. The squelch circuit allows adjusting the squelch to open at a programmable setting of the S-Meter, thus reducing guesswork in setting the squelch threshold.

We appreciate your purchase of the VX-3R, and encourage you to read this manual thoroughly, and learn about the many exciting features of your thrilling new Yaesu hand-held transceiver!

VX-3R O

PERATING

M

ANUAL

1

2

C

ONTROL

& C

ONNECTIONS

ANTENNA Jack

Connect the supplied rubber flex antenna (or another antenna presenting a 50-Ohm impedance) here.

MIC/SP Jack

This four-conductor miniature jack provides connection points for microphone audio, earphone audio, PTT, and ground.

DIAL Knob

The main tuning Dial is used for setting the operating frequency, and is used for audio volume level, menu selections, and other adjustments.

To rotate this Dial knob, pull the knob to unlock the mechanical dial lock, and then rotate the Dial knob.

PTT Switch

Press this switch to transmit, and release it to receive, after your transmission is completed.

MONI Switch

Pressing this key disables the noise squelching action, allowing you to hear very weak signals near the background noise level.

POWER Switch

Press and hold this switch in for one second to toggle the transceiver’s power on and off.

KEYPAD

These nine keys select many of most important operating features on the

VX-3R. The functions of the keys are described in detail on the pages to follow.

TX/BUSY Indicator

This indicator glows green when the squelch opens, and turns red during transmit. During

“Emergency” operation

(see page 74), this indicator will glow (or flash) white.

EAR Jack

This 3-pin miniature jack provides connection points for stereo earphones.

This 3-pin miniature jack allows connection to stereo earphones. When using after-market stereo earphones with this jack, you may enjoy the FM broadcast band in stereo.

MIC

The internal microphone is located here.

EXT DC Jack

This coaxial DC jack allows connection to an e x t e r n a l D C p o w e r source (3.5 - 7.0V DC).

The center pin of this jack is the Positive (+) connection.

SPEAKER

The internal speaker is located here.

VX-3R O

PERATING

M

ANUAL

K

EY

C

ONTROL

& C

ONNECTIONS

K

EYPAD

F

UNCTIONS

P

RIMARY

F

UNCTION

(P

RESS

K

EY

)

Switches the operating mode.

Moves operation to the next-highest frequency band. A c t i v a t e s t h e

“Memory Bank” feature while in the Memory Recall mode.

Switches the transmit power output between “HI” and “LOW”.

Switches frequency control between the VFO and

Memory Systems.

Activates the “Alternate” key function.

S

ECONDARY

F

UNCTION

(P

RESS

[F/W] + K

EY

)

Activates CTCSS or DCS operation.

Moves operation to the next-lowest frequency band. Holding this key after pressing the [F/W] key activate the key lockout feature.

Selects the synthesizer steps to be used during

VFO operation.

Activates the “Memory

Tune” function while in the

Memory Recall mode.

Disables the “Alternate” key function.

T

HIRD

F

UNCTION

(P

RESS AND

H

OLD

K

EY

)

A c t i v a t e s t h e S m a r t

Search™ and Channel

Counter features.

Activates the Scanner Upward (toward a higher frequency or a higher channel number).

Enters the Set (Menu)

Mode.

Activates the Dual Watch feature.

Reverses transmit and receive frequencies while working through a repeater.

Activates the WIRES™

(Internet Connection) feature.

Switches operation to the

“Home” (favorite frequency) channel.

Recalls the “Weather

Broadcast” channels and

Short-wave broadcast station channels.

Enables the antenna selection to be used.

Enter the Broadcast Reception mode.

While in the Broadcast Reception mode, press the

[BAND] key to toggle the receiving band between

“AM” broadcast band and

“FM” broadcast band.

N.A.

Activates the “Memory

Write” mode (for memory channel storage).

Activates the Emergency

Channel Operation. See page 74.

Activates the ARTS™ feature.

Activates the SUB-RX

Operation. See page 16.

Toggle the DIAL knob function between the “Frequency Control” and “Receiver Audio Control”.

Rotate the DIAL knob while holding the [VOL] key to adjust the audio volume level.

VX-3R O

PERATING

M

ANUAL

3

C

ONTROL

& C

ONNECTIONS

LCD D

ISPLAY

Memory Bank Active

Skip Memory Channel or

Preferential Memory Channel

Operating Band Number or Memory Channel Number

Repeater Shift Direction

CTCSS/DSC Operation

Priority Channel

Audio Volume Level

Internet Connection

Feature Active

Operating Frequency

Secondary Keypad Active

Dual Watch Active

Low TX Power Selected

Battery Saver Active

Battery Indicator

Bell Alarm Active

Key Lock Active

Automatic Power-Off Active

Operating Mode

Stereo Audio S- & PO Meter

4 VX-3R O

PERATING

M

ANUAL

A

CCESSORIES

& O

PTIONS

S

UPPLIED

A

CCESSORIES

FNB-82LI 3.7 V, 1000 mAh Rechargeable Lithium Ion Battery Pack ............. 1

NC-85B, C, U Ú 2.5-Hour Charger ............................................................................ 1

YHA-66 Antenna ........................................................................................... 1

Operating Manual ............................................................................................................. 1

Warranty Card ................................................................................................................... 1

CSC-92

CN-3

VC-25

MH-34

B4B

MH-37

A4B

CT-27

CT-44

FBA-37

FNB-82LI

E-DC-21

NC-85B, C, U Ú

A

VAILABLE

O

PTIONS

Soft Case

BNC-to-SMA Adapter

VOX Headset

Speaker/Microphone

Earpiece/Microphone

Cloning Cable

Microphone Adapter

Dry Cell Battery Case for 3 x “AA” Alkaline Cells

3.7 V, 1000 mAh Rechargeable Lithium Ion Battery Pack

DC Cable w/ Cigarette-Lighter Adapter

2.5-Hour Charger

Ú: “B” suffix is for use with 100-120 VAC, “C” suffix is for use with 230-240 VAC, and

“U” suffix is for use with 230 VAC.

Availability of accessories may vary. Some accessories are supplied as standard per local requirements, while others may be unavailable in some regions. Consult your Yaesu dealer for details regarding these and any newly available options Connection of any non-Yaesu-approved accessory, should it cause damage, may void the Limited Warranty on this apparatus.

VX-3R O

PERATING

M

ANUAL

5

I

NSTALLATION OF

A

CCESSORIES

A

NTENNA

I

NSTALLATION

The supplied antenna provides good results over the entire frequency range of the transceiver. However, for enhanced base station medium-wave and shortwave reception, you may wish to connect an external (outside) antenna, as the supplied antenna is very small and cannot be expected to provide high performance at these frequencies.

To install the supplied antenna, hold the bottom end of the antenna and screw it onto the mating connector on the transceiver until it is snug. Do not over-tighten by use of extreme force.

Notes:

Never transmit without having an antenna connected.

When installing the supplied antenna, never hold the upper part of the antenna while screwing it onto the mating connector on the transceiver.

If using an external antenna for transmission, ensure that the SWR presented to the transceiver is 1.5:1 or lower, to avoid excessive feedline loss.

I

NSTALLATION OF

FNB-82LI B

ATTERY

P

ACK

The FNB-82LI is a high-performance Lithium-Ion battery providing high capacity in a

very compact package. Under normal use, the FNB-82LI may be used for approximately

300 charge cycles, after which operating time may be expected to decrease. If you have an older battery that is displaying diminished capacity, you should replace the pack with a new one. Installation of the battery is easy and quick:

1. Slide the Battery Cover

Latch to the Unlock position and then slide the Battery Cover toward the bottom to remove it.

2. Install the FNB-82LI into the Battery Compartment.

3. Replace the Battery Cover

Small Stud

Do not break this

Battery Terminal

LOCK and then slide the Battery

Cover Latch into the

“Lock” position.

UNLOCK

Important Note:

There is a small stud in the Battery Compartment of the VX-3R. This stud is a switch for the battery detection. Please be careful not to break this stud while changing the battery.

6 VX-3R O

PERATING

M

ANUAL

I

NSTALLATION OF

A

CCESSORIES

B

ATTERY

C

HARGING

If the battery has never been used, or its charge is depleted, it may be charged by connecting the NC-85

Battery Charger, as shown in the illustration, to the EXT DC jack. If only

12 ~ 16 Volt DC power is available, the optional E-DC-21 DC Adapter

(with its cigarette lighter plug) may also be used for charging the battery.

While the battery is being charged, the display will indicate “CHGING ” and the TX/BUSY indicator will glow red.

The S-meter will deflect according to the charging status.

When charging is finished, the display will change to indicate

“CHGFUL ” and the TX/BUSY indicator will glow green.

The NC-85 is only designed for the charging of the VX-3R’s battery, and is not suitable for other purposes. Please be advised that the NC-

85 may contribute noise to TV and radio reception in the immediate vicinity, so we do not recommend its use adjacent to such devices.

Ð


1) Perform the battery charging where the ambient temperature range is 41 °F to 95 °F

(+5 °C to +35 °C). Charge out of this range could cause damage to the battery pack.

2) If the charge is not completed in three hours or if “CHGERR” appears in the display, the battery may be deteriorated. Do not attempt to forcibly charge the battery, Please contact your Yaesu dealer.

3) If you do not use the VX-3R for a long time, remove the FNB-82LI Lithium-Ion battery pack from the VX-3R, as battery leakage could cause damage to the VX-3R and FNB-82LI.

4) When an FNB-82LI Lithium-Ion battery pack is not used for a long time, please remove it from the transceiver. Also, while in storage, the charge will drain slightly over time and the battery should be recharged 50 % each six months.

VX-3R O

PERATING

M

ANUAL

7

8

I

NSTALLATION OF

A

CCESSORIES

I

NSTALLATION OF

FBA-37 A

LKALINE

B

ATTERY

C

ASE (OPTION)

The optional FBA-37 Battery Case allows operation of the VX-3R using three “AA” size alkaline batteries.

When installing batteries, insert the (–) end first, then press in the (+) end so the battery snaps into place. Always replace all three batteries at the same time, paying attention to the polarity indicated inside the case.

The FBA-37 must not be used with rechargeable cells. The FBA-

37 does not contain the thermal and over-current protection circuits (provided in the FNB-82LI Lithium-Ion Battery Pack) required when utilizing Ni-Cd and Ni-MH cells.


1) The FBA-37 is designed for use only with AA-type Alkaline cells.

2) If you do not use the VX-3R for a long time, remove the alkaline batteries from the

FBA-37, as battery leakage could cause damage to the VX-3R and FBA-37.

3) Never connect the external DC power supply to the VX-3R, when the FBA-37 Battery Pack is installed in the VX-3R.

B

ATTERY

L

IFE

I

NFORMATION

When the battery charge is almost depleted, a “ ” icon will appear on the display. When the “ ” icon appears, it is recommended that you charge the battery soon.

O

PERATING

B

AND

144 MHz Ú 1

430 MHz Ú 1

AM/FM

Broadcast Band Ú 2

B

ATTERY

L

IFE

(A

PPROX

.)

FNB-82LI

6.0 hours

6.5 hours

20.0 hours

FBA-37

7.0 hours

7.5 hours

25.0 hours

B

ATTERY

I

NDICATOR

No Icon: Enough Battery Power

: Lower Battery Power

(Blinking): Prepare to charge

(or replace) the Battery

Ú 1: TX: 6 seconds, RX: 6 seconds, and Squelched: 48 seconds.

Ú 2: Continuous signal reception.

The current battery voltage can be displayed manually on the display, via the Set Mode

Item 23: DC VLT .

Battery capacity may be reduced during extremely cold weather operation. Keeping the radio inside your parka may help preserve the full charge capacity.

VX-3R O

PERATING

M

ANUAL

I

NTERFACE OF

P

ACKET

TNC

S

The VX-3R may be used for Packet operation using the optional CT-91 microphone adapter

(available from your Yaesu dealer) for easy interconnection to commonly-available connectors wired to your TNC. You may also build your own cable, using a four-conductor miniature phone plug, per the diagram below.

The audio level from the receiver to the TNC may be adjusted by the transceiver’s volume control, as with voice operation (Rotate the DIAL knob while pressing and holding the

[VOL] key, do not forget to pull the DIAL knob to rotate the DIAL knob). The input level to the VX-3R from the TNC should be adjusted at the TNC side. The optimum input audio voltage is approximately 5 mV at 2000 Ohms.

Be sure to turn the transceiver and TNC off before connecting the cables, to prevent voltage spikes from possibly damaging your transceiver.

When you are operating in Packet Mode, switch the Receive Battery Saver OFF, as the

“sleep” cycle may “collide” with the beginning of an incoming Packet transmission, causing your TNC not to receive the full data burst. See page 93 for details regarding

Battery Saver setup.

VX-3R O

PERATING

M

ANUAL

9

O

PERATION

Hi! I’m R. F. Radio, and I’ll be helping you along as you learn the many features of the VX-3R. I know you’re anxious to get on the air, but I encourage you to read the “Operation” section of this manual as thoroughly as possible, so you’ll get the most out of this fantastic new transceiver. Now. . .let’s get operating!

S

WITCHING

P

OWER

O

N AND

O

FF

1. Be sure the Battery Pack is installed, and that the battery is fully charged. Connect the antenna to the top panel ANTENNA jack.

2. Press and hold in the orange POWER switch (on the left side of the transceiver) for one second. Two beeps will be heard when the switch has been held long enough, and the current DC supply voltage will appear on the display for 2 seconds. If you are using the FNB-82LI Battery Pack, the small “Lit ” icon at the top of the display confirms that the

Lithium-Ion Battery Pack has been detected. After this 2-second interval, the display will resume its normal indication of the operating frequency.

3. To turn the VX-3R off, press and hold in the orange POWER switch again for one second.

1) If you don’t hear the two “Beep” tones when the radio comes on, the Beeper may have been disabled via the Set Mode Item 14: BP SEL. See page 19, which tells you how to reactivate the Beeper.

2) You can change the Opening Message (DC supply voltage indication) to any desired message (up to 6 characters) via Set Mode Item 59: OPN.MSG; see page 115 for details.

A

DJUSTING THE

V

OLUME

L

EVEL

Pull the DIAL knob to unlock the mechanical dial lock, then rotate the DIAL knob while pressing and holding the [VOL] key to set the desired audio level. Clockwise rotation increases the volume level.

1) You may set the Audio Output Level to the

Speaker, and the Earphone Output Level individually. The “SP” notation (which means Speaker) appears in the Memory Channel Number display slot while adjusting the Speaker Output Level. The “HP” notation

(which means Headphone) appears in the Memory Channel Number display slot while adjusting the Earphone Output Level.

2) When pressing the [F/W] key followed by the [VOL] key, the DIAL knob function changes to the Volume Level selection instead of the frequency control. In this case, the

“VOL” notation on the display blinks. Pressing the [F/W] key followed by the [VOL] key again, the DIAL knob function returns to the frequency control. Furthermore, you may change the [VOL] key function via Set Mode Item 92: VOL MD. See page 101 for details.

10 VX-3R O

PERATING

M

ANUAL

O

PERATION

S

QUELCH

A

DJUSTMENT

The VX-3R’s Squelch system allows you to mute the background noise when no signal is being received. The Squelch system make “standby” operation more pleasant, and significantly reduces battery current consumption.

The Squelch system may be adjusted independently for the FM and Wide-FM (FM Broadcast) modes.

1. Press the [F/W] key, followed by the MONI switch on the left side of the radio. This provides a “Short-cut” to Set Mode Item

78: SQ LVL .

2. Now, rotate the DIAL knob to set the Squelch so that the background noise is just silenced (typically at a setting of about “1 ” or “2 ” for AM/FM, and “2 3 ” for Wide-FM/FM Broadcast/

AM Broadcast). This is the point of maximum sensitivity to weak signals.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob.

3. When you are satisfied with the Squelch threshold setting, press the PTT switch momentarily to save the new setting and exit to normal operation.

1) The VX-3R can set the squelch threshold level on the AM mode, FM mode,

Wide FM mode, and AM Broadcast individually.

2) A special “S-meter Squelch” feature is provided on the VX-3R. This feature allows you to set the squelch so that only signals exceeding a certain S-meter level will open the squelch. See page 22 for details.

3) If you’re operating in an area of high RF pollution, you may need to consider “Tone

Squelch” operation using the built-in CTCSS Decoder. This feature will keep your radio quiet until a call is received from a station sending a carrier, which contains a matching

(subaudible) CTCSS tone. Or, if your friends have radios equipped with DCS (Digital

Coded Squelch) like your VX-3R has, try using that mode for silent monitoring of busy channels.

VX-3R O

PERATING

M

ANUAL

11

O

PERATION

S

ELECTING THE

O

PERATING

B

AND

The VX-3R covers an incredibly wide frequency range, over which a number of different operating modes are used.

Therefore, the VX-3R’s frequency coverage has been divided into different operating bands, each of which has its own pre-set channel steps and

O

PERATING

B

AND

[B

AND

N

UMBER

]

SW Band [1]

50 MHz Ham Band [2]

Air Band [3]

144 MHz Ham Band [4]

VHF-TV Band [5]

Information Band 1 [6]


UHF-TV Band [8]


F

REQUENCY

R

ANGE

USA V

ERSION

1.8 - 30 MHz

EXP V

ERSION

1.8 - 30 MHz

30 - 76 MHz

108 - 137 MHz

137 - 174 MHz

174 - 222 MHz

30 - 76 MHz

108 - 137 MHz

137 - 174 MHz

174 - 222 MHz

222 - 420 MHz

420 - 470 MHz

470 - 774 MHz

803 - 999 MHz

222 - 420 MHz

420 - 470 MHz

470 - 800 MHz

803 - 999 MHz operating modes. You can change the channel steps and operating modes later, if you like

(see page 21).

To Change Operating Bands:

1. Press the [BAND] key repetitively. You will see the LCD indication move toward a higher frequency band each time you press the [BAND] key.

Indicates a Band Number according to the receiving frequency in the Memory Channel Number Display Slot of the display.

2. If you wish to move the operating band selection downward

(toward lower frequencies), press the [F/W] key first, then press the [BAND] key.

3. Once you have selected the desired band, you may initiate manual tuning (or scanning) per the discussion in the next chapter.

Operating Band

1) The VX-3R has an AM / FM broadcast radio. You can receive these bands independently. See page 15 for details.

2) If desired, you may omit (skip) one or more bands from the band selection loop for faster recall of your favorite operating bands. See page 100 for details.

12 VX-3R O

PERATING

M

ANUAL

O

PERATION

F

REQUENCY

N

AVIGATION

The VX-3R will initially be operating in the “VFO” mode. This is a channelized system which allows free tuning throughout the currently-selected operating band.

Two basic frequency navigation methods are available on the VX-3R:

1) T

UNING

D

IAL

Rotation of the DIAL knob allows tuning in the pre-programmed steps established for the current operating band. Clockwise rotation of the DIAL knob causes the VX-3R to be tuned toward a higher frequency, while counter-clockwise rotation will lower the operating frequency.

If you press the [F/W] key momentarily, then rotate the DIAL knob, frequency steps of 1 MHz will be selected. This feature is extremely useful for making rapid frequency excursions over the wide tuning range of the VX-3R.


2) S

CANNING

From the VFO mode, press and hold in the [BAND] key for one second, and while still holding in the [BAND] key, rotate the

DIAL knob to select the bandwidth for the VFO scanner. Release the [BAND] key to begin scanning toward a higher frequency. The scanner will stop when it receives a signal strong enough to break through the Squelch threshold. The VX-3R will then hold on that frequency according to the setting of the “RESUME” mode (Set Mode

Item 75: SCN.RSM

). See page 54 for more details regarding Scan Operation.

If you wish to reverse the direction of the scan (i.e. toward a lower frequency, instead of a higher frequency), just rotate the DIAL knob one click in the counter-clockwise direction while the VX-3R is scanning. The scanning direction will be reversed. To revert to scanning toward a higher frequency once more, rotate the DIAL knob one click clockwise.

Press the PTT switch momentarily to cancel the scanning. This only stops the scan; it does not cause transmission to occur.

Notice

The VX-3R may receive very strong signals on the Image frequency. If you experience interference that you suspect may be coming in via an “image” path, you may calculate the possible frequencies using the formulas below. This information may be used in the design of effective countermeasures such as traps, etc.

3.579545 MHz x n 11.7 MHz x n (n is an integer: 1, 2, 3, …..)

VX-3R O

PERATING

M

ANUAL

13

O

PERATION

T

RANSMISSION

Once you have set up an appropriate frequency inside one of the 144 MHz or 430 MHz

Amateur bands on which the VX-3R can transmit, you’re ready to go on the air! These are the most basic steps; more advanced aspects of transmitter operation will be discussed later.

1. To transmit, press the PTT switch, and speak into the front panel microphone (located in the upper left-hand corner of the speaker grille) in a normal voice level. The TX/BUSY indicator will glow red during transmission.

2. To return to the receive mode, release the PTT switch.

3. During transmission, the relative power level will be indicated on the bar graph at the bottom of the

LCD. Full-scale deflection confirms “High

Power” operation, while deflection of two bars indicates “Low Power” operation. Additionally, the “ ” icon will appear at the bottom of the display while operating on the “Low Power” setting.

4. If you’re just talking to friends in the immediate area, you’ll get much longer battery life by switching to Low Power operation. To do this, press the [TXPO] key so that the

“ ” icon appears at the bottom of the display. And don’t forget: always have an antenna connected when you transmit.

Transmission is possible only on the 144 MHz and 430 MHz bands.

1) The VX-3R is smart! You can set up Low power on 144 MHz band, while leaving 430 MHz on High power, and the radio will remember the different settings on both bands. And when you store memories, you can store High and Low power settings separately in each memory, so you don’t waste battery power when using very close-in repeaters!

2) When you are operating on the Low power setting, you can press the [F/W] key, before you press the PTT switch, to cause the VX-3R to transmit (temporarily) on High power. After one transmission, the power level will revert to the previously-selected (Low power) setting.

O

PERATING

B

AND

144 MHz

430 MHz

T

RANSMIT

P

OWER

FBA-37/FNB-82LI

Hi: 1.5 W

Low: 0.1 W

Hi: 1.5 W

Low: 0.1 W

EXT DC (6.0 V)

Hi: 3.0 W

Low: 0.3 W

Hi: 2.0 W

Low: 0.3 W

14 VX-3R O

PERATING

M

ANUAL

O

PERATION

AM

AND

FM B

ROADCAST

R

ECEPTION

The VX-3R includes provision for reception of AM and FM broadcasts. FM broadcast reception, utilizes a wide-bandwidth filter and stereo decoder which provides excellent fidelity.

1. Press the [RADIO] key momentarily to enter the Broadcast

Reception mode.

2. Press the [BAND] key to toggle the receiving band between

“AM broadcast” and “FM broadcast”.

The AM broadcast coverage is 510 to 1790 kHz and utilizes AM mode. The “ ” notation (which means AM) appears in the Memory Channel Number display slot and an “ ” icon appears on the bottom left of the LCD.

The FM broadcast coverage is 76.00 to 107.90 MHz and utilizes Wide-FM mode. The “ ” notation (which means

FM) appears in the Memory Channel Number display slot and “ ” icon appears on the bottom left of the LCD.

3. Rotate the DIAL knob to select the desired station. When receiving an FM stereo signal, “ “ icon will appear at the bottom left of the display.


4. Press and hold the [RADIO] key for one second to enable the antenna selection to be used by rotating the DIAL knob. Available selections are:

AM: “BARANT ” (Uses the internal Bar Antenna) or “BAREXT ” (Uses both the internal Bar Antenna and the Rubber Flex Antenna).

FM: “EXTANT ” (Uses the Rubber Flex Antenna) or “EARPHO ” (Uses the Earphone

Antenna).

5. When you finish the selection, press the [RADIO] key momentarily to exit from the antenna selection mode.

6. Press the [RADIO] key momentarily again to exit from the AM and FM Broadcast

Reception mode and return to normal operation.

If you wish to output the audio of the FM Broadcast station to the VX-3R internal speaker while using the earphone antenna, select Set Mode Item 77:

SP OUT to “SPKR”.

VX-3R O

PERATING

M

ANUAL

15

O

PERATION

AM

AND

FM B

ROADCAST

R

ECEPTION

SUB-RX O

PERATION

The SUB-RX Operation allows you to monitor your desired amateur band frequency while receiving AM or FM broadcast stations. Furthermore, you may transmit on the amateur frequency by pressing the PTT switch.

When a signal is received in the amateur band, the audio is output instead of the AM or FM

Broadcast station. When the amateur band signal drops, the SUB-RX Operation is resumed as determined by the user settings in the below procedures.

1. Set the VX-3R to the desired amateur band frequency by the VFO or Memory channel selection.

2. Press the [F/W] key then press the [RADIO] key.

3. Rotate the DIAL knob to select the resume mode of the SUB-RX

Operation. Available selections are:

TX 1S - TX 10S : Sets the period of time after you transmit an amateur signal before the AM or FM Broadcast station will be heard from the speaker, and the SUB-RX Operation is resumed.

However, if a signal is received in the amateur band, the SUB-

RX Operation will halt on the amateur band frequency and the

SUB-RX Operation does not resume.

TRX 1S - TXR 10S : When the selected time passes after the amateur band signal

HOLD : drops or transmission is over, the AM or FM Broadcast station will be heard from the speaker and the SUB-RX Operation is resumed.

When a signal is received in the amateur band or if you transmit on the amateur band, the SUB-RX Operation will halt on the amateur band frequency (the SUB-RX Operation does not resume.). You must manually re-initiate the SUB-RX Operation, if you wish to resume.

OFF : Disable the SUB-RX Operation.


4. Press the [RADIO] key to exit from the resume mode selection mode of the SUB-RX

Operation.

5. Press the [RADIO] key again to activate the SUB-RX Operation. The “ ” icon appears above volume level indicator on the display.

6. Press the [BAND] key to toggle the receiving band between “AM broadcast” and “FM broadcast”.

16 VX-3R O

PERATING

M

ANUAL

O

PERATION

AM

AND

FM B

ROADCAST

R

ECEPTION

7. Rotate the DIAL knob to select the desired Broadcast station.

8. When a signal is received in the amateur band, the amateur band audio is output to the speaker. The AM or FM Broadcast station will no longer be heard. When the amateur band signal drops, the AM or FM Broadcast station will be heard from the speaker, and SUB-RX Operation is resumed (the amateur band frequency is monitored while the AM broadcast station is heard from the speaker) according to the SUB-RX Operation Resume mode selected in step 3 above.

9. You may monitor the amateur band forcibly by holding the MONI switch.

To disable the SUB-RX Operation, just repeat the above procedure, rotating the DIAL knob to select “OFF ” in step 3 above.

1) You may transmit with the VX-3R on the frequency set in step1 above by pressing the PTT switch, even if the SUB-RX Operation is activated.

2) You may change the frequency of the amateur band by rotating the DIAL knob while pressing the MONI switch.

3) When the [V/M] key is pressed, the VX-3R recalls AM and FM Broadcast station memories only. In this case, the “ ” icon will blink.

VX-3R O

PERATING

M

ANUAL

17

A

DVANCED

O

PERATION

Now that you’re mastered the basics of VX-3R operation, let’s learn more about some of the really neat features.

K

EYBOARD

L

OCKING

In order to prevent accidental frequency change or inadvertent transmission, various aspects of the VX-3R’s keys and switches may be locked out. The possible lockout combinations are:

KEY : The front panel keys are locked out

PTT : The PTT switch is locked (TX not possible)

KY+PTT : Both the keys and PTT switch are locked out

To lock out some or all of the keys:

1. Press and hold in the [TXPO] key for one second to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 46: LOCK .


3. Press the [TXPO] key momentarily to enable adjustment of this

Item.

4. Rotate the DIAL knob to choose between one of the locking schemes as outlined above.

5. When you have made your selection, press the PTT switch to save the new setting and return to normal operation.

To activate the locking feature, press the [F/W] key, then press and hold in the [BAND] key for one second. The “ ” icon will appear on the LCD. To cancel locking, repeat this process.

18 VX-3R O

PERATING

M

ANUAL

A

DVANCED

O

PERATION

A

DJUSTING THE

K

EYPAD

B

EEPER

V

OLUME

L

EVEL

A keypad beeper provides useful audible feed back whenever a keypad is pressed. The keypad beeper level changes according to the receiver audio volume level setting. However, you may adjust the volume balance between the receiving audio and keypad beeper via Set Mode Item 13: BP LVL .


2. Rotate the DIAL knob to select Set Mode Item 13: BP LVL .



Item.

4. Rotate the DIAL knob to select the desired level.


Additionally, if you want to turn the beep off:


2. Rotate the DIAL knob to select Set Mode Item 14: BP SEL .



Item.

4. Rotate the DIAL knob to change the setting to “OFF ”.

5. Press the PTT switch to save the new setting and return to normal operation.

6. If you wish to re-enable the Beeper, just repeat the above procedure, rotating the DIAL knob to select “KEY ” or “KY+SCN ” in step “4” above.

KEY : The beeper sounds when you press any key.

KY+SCN : The beeper sounds when you press a key or when the scanner stops.

VX-3R O

PERATING

M

ANUAL

19

A

DVANCED

O

PERATION

K

EYPAD

/LCD I

LLUMINATION

Your VX-3R includes a reddish illumination lamp which aids in nighttime operation. The red illumination yields clear viewing of the display in a dark environment, with minimal degradation of your night vision. Three options for activating the lamp are provided:

KEY 2S - KEY10S : Illuminates the Keypad/LCD for the selected illumination time when any key pressed.

CONT :

OFF :

Illuminates the Keypad/LCD continuously.

Disables the Keypad/LCD lamp.

Here is the procedure for setting up the Lamp mode:


2. Rotate the DIAL knob to select Set Mode Item 44: LAMP .



Item.

4. Rotate the DIAL knob to select one of the three modes described above.

5. When you have made your choice, press the PTT switch to save the new setting and return to normal operation.

C

HECKING THE

B

ATTERY

V

OLTAGE

The VX-3R’s microprocessor includes programming which will detect the battery type and measure the current battery voltage.


2. Rotate the DIAL knob to select Set Mode Item 23: DC VLT .


3. Press the [TXPO] key momentarily to display the battery type and the current DC voltage being supplied.

Lit : FNB-82LI is in use.

Edc : An external DC source is in use.

4. Press and hold in the [TXPO] key for one second to return to normal operation.

20 VX-3R O

PERATING

M

ANUAL

A

DVANCED

O

PERATION

C

HANGING THE

C

HANNEL

S

TEPS

The VX-3R’s frequency synthesizer provides the option of utilizing channel steps of 5/8.33/9/

10/12.5/15/20/25/50/100 kHz per step (optional values differ depending on the band selected).

A number of steps may be important to your operating requirements. Automatic (“AUTO”) step selection is based on the current operating frequency. The VX-3R is set up at the factory in the “AUTO” configuration, which probably is satisfactory for most operation. However, if you need to change the channel step increments, the procedure to do so is very easy.


2. Rotate the DIAL knob to select Set Mode Item 82: STEP .



Item.

4. Rotate the DIAL knob to select the new channel step size.


1) 9 kHz steps are available only when receiving on the BC band.

2) 8.33 kHz steps are available only when receiving on the Air band.

3) While operating on the BC band, you may only select channel steps of 9 kHz or 10 kHz; the other step selections are disabled.

4) 5 kHz steps are not available for use on 250 - 300 MHz, nor above 580 MHz.

C

HANGING THE

R

ECEIVING

M

ODE

The VX-3R provides for automatic mode changing when the radio is tuned to different operating frequencies. However, should an unusual receiving situation arise in which you need to change to a different receiving mode, just press the [MODE] key. The receiving modes available are:

AUTO : Automatic mode sets the default values for the selected frequency range.

FM : Narrow-bandwidth FM (used for voice communication)

AM : Amplitude Modulation

W-FM : Wide-bandwidth FM (used for high-fidelity broadcasting)

Unless you have a compelling reason to do so, leave the Automatic Mode

Selection feature on, this will save time and trouble when changing bands. If you make a mode change for a particular channel or station, you can always store that one channel into memory, as the mode setting will be memorized along with the frequency information.

VX-3R O

PERATING

M

ANUAL

21

A

DVANCED

O

PERATION

S-

METER

S

QUELCH

A special S-meter Squelch feature is provided on this radio. This feature allows you to set the squelch so only signals exceeding a certain S-meter level will open the squelch.

To set up the S-meter squelch circuit for operation, use the following procedure:


2. Rotate the DIAL knob to select Set Mode Item 80: SQSMTR .



Item.

4. Rotate the DIAL knob to select the desired signal strength level for the squelch threshold (LVL 1 - LVL8 OFF ).

5. Press the PTT switch to save the new setting and return to normal operation.

1) When the S-meter squelch is activated, the S-meter segment corresponding to the squelch threshold which was set by step 4 above will blink.

2) The receiver’s squelch will open based on the higher of the levels set by the two squelch systems (Noise Squelch and S-meter Squelch).

For example: a) If the Noise Squelch (SQL control) is set so that signals at a level of “S-3” will open the squelch, but the S-meter Squelch (Set Mode Item 80) is set to “LVL 5,” the squelch will only open on signals which are “S5” or stronger on the S-meter.

b) If the S-meter Squelch is set to “S3,” but the Noise Squelch is set to a high level which will only pass signals which are Full Scale on the S-meter, the squelch will only open on signals which are Full Scale on the S-meter. In this case, the Noise Squelch overrides the action of the S-meter Squelch.

22 VX-3R O

PERATING

M

ANUAL

A

DVANCED

O

PERATION

C

HECKING THE

T

EMPERATURE

The VX-3R can display the radio’s inside case temperature, measured by an internal sensor.


2. Rotate the DIAL knob to select Set Mode Item 85: TEMP .


3. Press the [TXPO] key momentarily to indicate the current temperature inside the transceiver’s case.

(°C)).

5. Press the PTT switch to save the new setting and exit to normal operation.

VX-3R O

PERATING

M

ANUAL

23

R

EPEATER

O

PERATION

Repeater stations, usually located on mountaintops or other high locations, provide a dramatic extension of the communication range for low-powered hand-held or mobile transceivers. The VX-3R includes a number of features which make repeater operation simple and enjoyable.

R

EPEATER

S

HIFTS

Your VX-3R has been configured, at the factory, for the repeater shifts customary in your country. For the 144 MHz band shift will be 600 kHz. On the 430 MHz band, the shift may be 1.6 MHz, 7.6 MHz, or 5 MHz (USA version).

Depending on the part of the band in which you are operating, the repeater shift may be either downward ( ) or upward ( ). One of these icons will appear at the top of the LCD when repeater shifts have been enabled.

A

UTOMATIC

R

EPEATER

S

HIFT

(ARS)

The VX-3R provides a convenient Automatic Repeater Shift feature, which causes the appropriate repeater shift to be applied automatically whenever you tune into the designated repeater sub-bands in your country. These sub-bands are shown below.

If the ARS feature does not appear to be working, you may have accidentally disabled it.

To re-enable ARS:


2. Rotate the DIAL knob to select Set Mode Item 5: ARS .



Item.

4. Rotate the DIAL knob to select “ON ” (to enable Automatic Repeater Shift).


145.1

145.5

ARS-Repeater Subbands

146.0

2-m

Version A

146.4

147.0

147.6

148.0

146.6

145.6

145.8

European Version

147.4

70-cm

440.0

Version A

445.0

438.20

433.00

433.40

434.60

435.00

450.0

439.45

Euro Version 1

Euro Version 2

24 VX-3R O

PERATING

M

ANUAL

R

EPEATER

O

PERATION

M

ANUAL

R

EPEATER

S

HIFT

A

CTIVATION

If the ARS feature has been disabled, or if you need to set a repeater shift direction other than that established by the ARS, you may set the direction of the repeater shift manually.

To do this:


2. Rotate the DIAL knob to select Set Mode Item 68: RPT .



Item.

4. Rotate the DIAL knob to select the desired shift among “–RPT ,”

“+RPT ,” and “SIMP .”


If you make a change in the shift direction, but still have Automatic Repeater

Shift engaged (see previous section), when you change frequency (by rotating the DIAL knob, for example) the ARS will over-ride your manual setting of the shift direction. Turn ARS off if you do not wish this to happen.

C

HANGING THE

D

EFAULT

R

EPEATER

S

HIFTS

If you travel to a different region, you may need to change the default repeater shift so as to ensure compatibility with local operating requirements.

To do this, follow the procedure below:

1. Set the VX-3R’s frequency to the band on which you wish to change the default repeater shift (144 MHz or 430 MHz Ham Band).


3. Rotate the DIAL knob to select Set Mode Item 69: RPT.SFT

.



Item.

5. Rotate the DIAL knob to select the new repeater shift magnitude.


If you just have one “odd” split that you need to program, don’t change the

“default” repeated shifts using this Set Mode Item! Enter the transmit and receive frequencies separately, as shown on page 43.

VX-3R O

PERATING

M

ANUAL

25

R

EPEATER

O

PERATION

C

HECKING THE

R

EPEATER

U

PLINK

(I

NPUT

) F

REQUENCY

It often is helpful to be able to check the uplink (input) frequency of a repeater, to see if the calling station is within direct (“Simplex”) range.

To do this, just press the [HM/RV] key. You’ll notice that the display has shifted to the repeater uplink frequency. Press the [HM/RV] key again to cause operation to revert to normal monitoring of the repeater downlink (output) frequency.

The configuration of this key may be set either to “RV” (for checking the input frequency of a repeater), or “HM” (for instant switching to the “Home” channel for the band you are operating on). To change the configuration of this key, use Set Mode Item 36: HM/RV. See page 111.

26 VX-3R O

PERATING

M

ANUAL

N

OTE

R

EPEATER

O

PERATION

VX-3R O

PERATING

M

ANUAL

27

CTCSS/DCS/EPCS O

PERATION

CTCSS O

PERATION

Many repeater systems require that a very-low-frequency audio tone be superimposed on your FM carrier in order to activate the repeater. This helps prevent false activation of the repeater by radar or spurious signals from other transmitters. This tone system, called

“CTCSS” (Continuous Tone Coded Squelch System), is included in your VX-3R, and is very easy to activate.

CTCSS setup involves two actions: setting the Tone Frequency and then setting of the Tone Mode. These actions are set up by using the [MODE] key or

Set Mode Items 79: SQ TYP and 86: TN FRQ.

1. Press the [F/W] key, then press the [MODE] key. This provides a “Short-cut” to Set

Mode Item 79: SQ TYP .

2. Rotate the DIAL knob so that “TONE ” appears on the display.

This activates the CTCSS Encoder, which allows repeater access.


3. Rotation of the DIAL knob one more “click” in step “2” above will cause the “TSQL ” notation to appear. When “TSQL ” is displayed, this means that the Tone Squelch system is active, which mutes your VX-3R’s receiver until it receives a call from another radio sending out a matching CTCSS tone. This can helpful in a high RF congested location by keeping your radio quiet until a call is received from a specific station.

28

You may notice an additional “DCS ” icon appearing while you rotate the DIAL knob in step 3 above. We’ll discuss the Digital Code Squelch system shortly.

You may notice “RV TN ” indication on the display while you rotate the DIAL knob in step 3 above, this means that the Reverse Tone Squelch system is active, which mutes your VX-3R’s receiver when it receives a call from the radio sending a matched CTCSS tone. The “ ” icon will blink on the display when the Reverse Tone Squelch system is activated.

You may notice “PR FRQ ” indication on the display while you rotate the

DIAL knob in step 3 above, this means that User programmed Reverse CTCSS

Decoder mutes your VX-3R’s receiver when it receives a call from the radio sending the CTCSS tone your programmed matching tone (determine from

Set Menu Item: 63: PR FRQ ) is received. The “ ” icon will appear on the display when the User programmed Reverse CTCSS Decoder is activated.

You may notice “PAGER ” and “MESSAGE ” indication on the display while you rotate the DIAL knob in step 3 above. These appear when the “Enhanced

Paging & Code Squelch” and the “Message Feature” are activated. We’ll discuss these functions later.

VX-3R O

PERATING

M

ANUAL


PERATION

CTCSS O

PERATION

4. When you have made your selection of the CTCSS tone mode, press the PTT switch to save the new setting.


6. Rotate the DIAL knob to select Set Mode Item 86: TN FRQ .


7. Press the [TXPO] key momentarily to enable adjustment of the

CTCSS frequency.

8. Rotate the DIAL knob until the display indicates the Tone Frequency you need to be using (ask the repeater owner/operator if you don’t know the tone frequency).

9. When you have made your selection, press the [TXPO] key momentarily, then press the PTT switch, to save the new settings and exit to normal operation. This is different from the usual method of restoring normal operation, and it applies only to the configuration of the CTCSS/DCS frequencies.

1) Your repeater may or may not re-transmit a CTCSS tone - some systems just use CTCSS to control

CTCSS TONE FREQUENCY (Hz)

67.0

69.3

71.9

74.4

77.0

79.7

82.5

85.4

88.5

91.5

94.8

97.4

access to the repeater, but does not pass it along when transmitting. If the S-Meter deflects, but the VX-3R is not passing audio, repeat steps “1” through “4” above, but ro-

100.0

103.5

107.2

110.9

114.8

118.8

123.0

127.3

131.8

136.5

141.3

146.2

151.4

156.7

159.8

162.2

165.5

167.9

171.3

173.8

177.3

179.9

183.5

186.2

tate the DIAL so that “TSQ” disappears - this will allow you to hear all traffic on the chan-

189.9

192.8

196.6

199.5

203.5

206.5

210.7

218.1

225.7

229.1

233.6

241.8

250.3

254.1

– – – – nel being received.

2) During CTCSS operation, you may set up the VX-3R so a ringing “bell” sound alerts you to an incoming call. See page 37 for details.

VX-3R O

PERATING

M

ANUAL

29


PERATION

DCS O

PERATION

Another form of tone access control is Digital Code Squelch, or DCS. It is a newer, more advanced tone system which generally provides more immunity from false paging than does CTCSS. The DCS Encoder/Decoder is built into your VX-3R, and operation is very similar to that just described for CTCSS. Your repeater system may be configured for

DCS. If not, DCS is frequently quite useful in Simplex operation if your friend(s) use transceivers equipped with this advanced feature.

R.F. Says: Just as in CTCSS operation, DCS requires that you set the Tone Mode to DCS and that you select a digital code.



2. Rotate the DIAL knob until “DCS ” appears on the display; this activates the DCS Encoder/Decoder.


3. Press the PTT switch to save the new setting.


5. Rotate the DIAL knob to select Set Mode Item 24: DCS CD .

6. Press the [TXPO] key momentarily to enable the adjustment of the DCS code.

7. Rotate the DIAL knob to select the desired DCS Code (a threedigit number). Ask the repeater owner/operator if you don’t know the DCS Code. If you are working simplex, just set up the DCS

Code to be the same as that used by your friend(s).

8. When you have made your selection, press the [TXPO] key momentarily, then press the PTT switch to save the new settings and exit to normal operation.

1) Remember that DCS is an Encode/Decode system, so your receiver will remain muted until a matching DCS code is received on an incoming transmission. Switch the DCS off when you’re just tuning around the band!

2) During DCS operation, you may set up the

VX-3R so a ringing “bell” sound alerts you to an incoming call. See page 37 for details.

DCS CODE

023 025 026 031 032 036 043 047 051 053

054 065 071 072 073 074 114 115 116 122

125 131 132 134 143 145 152 155 156 162

165 172 174 205 212 223 225 226 243 244

245 246 251 252 255 261 263 265 266 271

274 306 311 315 325 331 332 343 346 351

356 364 365 371 411 412 413 423 431 432

445 446 452 454 455 462 464 465 466 503

506 516 523 526 532 546 565 606 612 624

627 631 632 654 662 664 703 712 723 731

732 734 743 754 – – – – – –

30 VX-3R O

PERATING

M

ANUAL


PERATION

DCS O

PERATION

DCS C

ODE

I

NVERSION

The DCS system was first introduced in the commercial LMR (Land Mobile Radio) service, where it is now in widespread use. DCS is sometime referred to by its different proprietary names, such as DPL ® (Digital Private Line ® , a registered trademark of Motorola, Inc.).

DCS uses a codeword consisting of a 23-bit frame, transmitted (subaudible) at a data rate of 134.4 bps (bit/sec). Occasionally, signal inversion can result in the complement of a code being sent or received. This prevents the receiver’s squelch from opening with DCS enabled, as the decoded bit sequence would not match that selected for operation.

Typical situations that might cause inversion to occur are:

Connection of an external receiver preamplifier.

Operating through a repeater.

Connection of an external linear amplifier.

Note that code inversion does not mean that any of the above listed equipment is defective!

In certain amplifier configurations, the output signal (phase) is inverted from the input. Small signal or power amplifiers having an odd number (1, 3, 5, etc.) of amplification stages may result in inversion of a transmitted or received DCS code. While under most circumstances this should not occur (amplifier designs and industry standards take this into account), if you find that your receiver squelch does not open when both you and the other station are using a common DCS code, you or the other station (but not both) can try the following:


2. Rotate the DIAL knob to select Set Mode Item 25: DCS RV .



Set Mode Item.

4. Rotate the DIAL knob to select one of the following modes:

R-N.T-N : Receive and transmit the Normal DCS Tone.

R-I.T-N : Receive the Inverted DCS Tone and transmit the Normal DCS Tone.

R-B.T-N : Receive both Normal and Inverted DCS Tones and transmit the Normal DCS

Tone.

R-N.T.I

: Receive the Normal DCS Tone and transmit the Inverted DCS Tone.

R-I.T-I : Receive and transmit the Inverted DCS Tone.

R-B.T-I : Receive both Normal and Inverted DCS Tones and transmit the Inverted

DCS Tone.

5. When you have made your selection, press the [TXPO] key momentarily, then press the PTT switch, to save the new settings and exit to normal operation.

VX-3R O

PERATING

M

ANUAL

31


PERATION

DCS O

PERATION

This is different from the usual method of restoring normal operation, and it applies only to the configuration of the CTCSS/DCS frequencies. Remember to restore the default setting

“R-N.T-N ” (Receive and transmit the Normal DCS Tone) when done.

T

ONE

S

EARCH

S

CANNING

In operating situations where you don’t know the CTCSS or DCS tone being used by another station or stations, you can command the radio to listen to the incoming signal and scan in search of the tone being used. Two things must be remembered in this regard:

You must be sure that your repeater uses the same tone type (CTCSS vs. DCS).

Some repeaters do not pass the CTCSS tone. You may have to listen to the station(s) transmitting on the repeater uplink (input) frequency in order to allow Tone Search

Scanning to work.

To scan for the tone in use:

1. Set the radio up for either CTCSS or DCS

Decoder operation (see the previous discussions). In the case of CTCSS, “ ” will appear on the display; in the case of DCS,

“ ” will appear on the display.


3. Rotate the DIAL knob to select Set Mode

Item 86: TN FRQ when TONE SQL is selected, or Set Mode Item 24: DCS CD during DCS operation.


4. Press the [TXPO] key momentarily to enable adjustment of the selected Set Mode Item.

5. Press and hold in the [BAND] key for one second, until “T SRCH ” (for CTCSS Tone

Search) or “D SRCH ” (for DCS Tone Search) appears on the display, then release the

[BAND] key to start scanning for the incoming CTCSS or DCS tone/code.

6. When the radio detects the correct tone or code, it will halt on that tone/code, and audio will be allowed to pass. Press the [BAND] key to lock in that tone/code, then press PTT switch to exit to normal operation.

32 VX-3R O

PERATING

M

ANUAL


PERATION

T

ONE

S

EARCH

S

CANNING

If the Tone Scan feature does not detect a tone or code, it will continue to scan indefinitely. When this happens, it may be that the other station is not sending any tone. You can press the PTT switch to halt the scan at any time.

You may listen to the (muted) signal from the other station during Tone Scanning when Set

Mode Item 88: TS MUT is set to “OFF .” See page 121 for details. You can also change the

Tone Search scanning speed, using Set Mode Item 89: TS SPD . See page 121.

Tone Scanning works either in the VFO or Memory modes.

VX-3R O

PERATING

M

ANUAL

33


PERATION

EPCS (E

NHANCED

P

AGING

& C

ODE

S

QUELCH

)

The VX-3R includes an Enhanced CTCSS tone encoder/decoder and a dedicated microprocessor providing paging and selective calling features. This allows you to place a call to a specific station (Paging), and to receive calls of your choice directed only to you (Code

Squelch).

The paging and code squelch systems use two pairs of (alternately switched) CTCSS tones which are stored in the pager memories. Basically, your receiver remains silent until it receives the CTCSS tone pair that matches those stored in the Receiving Pager Memory.

The squelch then opens so the caller is heard, and the paging ringer immediately sounds, if activated. When you close the PTT switch to transmit, the CTCSS tone pair that is stored in the Transmitting Pager Memory will be transmitted automatically.

On the paged radio, the Code Squelch will close automatically after the incoming page ends. Meanwhile, on the paging radio, the Enhanced Paging and Code Squelch system will be disabled after the PTT switch is released after the paging transmission. You may reactivate the Enhanced Paging and Code Squelch system again.

S

TORING THE

CTCSS T

ONE

P

AIRS FOR

EPCS O

PERATION


2. Rotate the DIAL knob to select Set Mode

Item 61: PAG.CDR

for the Receiving CTCSS for the Transmitting CTCSS Tone Pair.



Set Mode Item.

4. Rotate the DIAL knob to set the CTCSS Tone number which corresponds to the first tone of the CTCSS Tone Pair.

5. Press the [V/M] key, then rotate the DIAL knob to set the CTCSS

Tone number which corresponds to the second tone of the CTCSS

Tone Pair.


The VX-3R does not recognize the order of the 1st tone and the 2nd tone. In other words, for example, the VX-

3R considers both CTCSS pairs “10, 35” and “35, 10” to be identical.

34 VX-3R O

PERATING

M

ANUAL


PERATION

EPCS (E

NHANCED

P

AGING

& C

ODE

S

QUELCH

)

A

CTIVATING THE

E

NHANCED

P

AGING

& C

ODE

S

QUELCH

S

YSTEM



2. Rotate the DIAL knob until “PAGER ” appears on the display.

This activates Enhanced Paging & Code Squelch.


3. Press the PTT switch to save the new setting and activate the Enhanced Paging &

Code Squelch.

To disable the Enhanced Paging & Code Squelch, just repeat the above procedure, rotate the DIAL knob to select “OFF ” in step 2 above.

When the Enhanced Paging & Code Squelch feature is activated, the

“P ” notation will appear at the 100 MHz digit of the frequency display.

During Enhanced Paging & Code Squelch operation, you may set up the

VX-3R so that a ringing “bell” sound alerts you when a call is coming in. See page 37 for details.

04

05

06

07

No.

01

02

03

08

09

10

Hz

67.0

69.3

71.9

74.4

77.0

79.7

82.5

85.4

88.5

91.5

14

15

16

17

No.

11

12

13

18

19

20

CTCSS T

ONE

N

UMBER

Hz

94.8

97.4

100.0

103.5

107.2

110.9

114.8

118.8

123.0

127.3

No.

21

22

23

24

25

26

27

28

29

30

Hz

131.8

136.5

141.3

146.2

151.4

156.7

159.8

162.2

165.5

167.9

34

35

36

37

No.

31

32

33

38

39

40

Hz

171.3

173.8

177.3

179.9

183.5

186.2

189.9

192.8

196.6

199.5

44

45

46

47

No.

41

42

43

48

49

50

Hz

203.5

206.5

210.7

218.1

225.7

229.1

233.6

241.8

250.3

254.1

VX-3R O

PERATING

M

ANUAL

35


PERATION

EPCS (E

NHANCED

P

AGING

& C

ODE

S

QUELCH

)

P

AGING

A

NSWER

B

ACK

When you press the PTT switch to respond to a page call, the VX-3R transmits the same

CTCSS tone pair. This tone pair will open the Code Squelch of the calling station. If you prefer, you can have the VX-3R respond to page calls automatically (“transpond”). To enable this feature:


2. Rotate the DIAL knob to select Set Mode Item 60: PAG.ABK

.



Set Mode Item.

4. Rotate the DIAL knob to select “ON ”.


The Paging Answer Back feature constitutes a form of “remote control” operation that may be restricted to certain frequencies. U.S. users should confirm the current status of §97.201(b) of the FCC’s rules governing the Amateur service before utilizing this feature on the 144 MHz band.

36 VX-3R O

PERATING

M

ANUAL


PERATION

CTCSS/DCS/EPCS B

ELL

O

PERATION

During CTCSS Decode, DCS, or EPCS operation, you may set up the VX-3R so a ringing

“bell” sound (or user programmed beep) alerts you to an incoming call. Here is the procedure for activating the CTCSS/DCS/EPCS Bell:

1. Set the operating frequency to the desired channel.

2. Set the transceiver up for CTCSS Decode (“Tone Squelch”), DCS, or EPCS operation, as described previously.


4. Rotate the DIAL knob to select Set Mode Item 10: BEL.SEL

.



Set Mode Item.

6. Rotate the DIAL knob to set the desired “bell” sound. The available choices are BELL ,

USERBP1 , USERBP2 , USERBP3 , or OFF (disable the Bell function).

Note: When User Beep (described later) does not register,

USERBP1 , USERBP2 USERBP3 does not appear.

7. Press the [TXPO] key momentarily, then rotate the DIAL knob one click counter-clockwise to select Set Mode Item 9: BEL.RNG

.


Set Mode Item.

9. Rotate the DIAL knob to set the desired number of rings of the

Bell. The available choices are 1 through 20 CONT (continuous ringing).

10. Press the PTT switch momentarily to save the new setting and exit to normal operation.

When you are called by a station whose transceiver is sending a CTCSS tone, DCS code, or CTCSS tone pair which matches that set into your Decoder, the Bell will ring in accordance with this programming.

When the CTCSS/DCS/EPCS Bell is activated, the “ ” icon will appear in the display.

To disable the CTCSS/DCS/EPCS Bell function, select the setting of

Set Mode Item 10: BEL.SEL

to “OFF ”.

VX-3R O

PERATING

M

ANUAL

37


PERATION


ELL

O

PERATION

P

ROGRAMMING THE

U

SER

B

EEP

Three User Beep Memories are provided, allowing you to create a unique original beep tone.

Each User Beep Memory can store up to 64 steps with three octaves (“C1 ” through “B3 ”).


2. Rotate the DIAL knob to select Set Mode Item 15: BP USR .



Set Mode Item.

4. Rotate the DIAL knob to select the memory slot into which you wish to store your programmed beep. Available selections are bP1 , bP2 bP3 . The previously stored beep will be displayed.

5. Press the [V/M] key to enable programming the beep. Press and hold the [HM/RV] key for one second to clear any previous beep, if desired.

6. Rotate the DIAL knob to select the first beep tone of the User

Beep.

7. Press the [V/M] key, then rotate the DIAL knob to set the length of the first beep tone. Available selections are 1 (0.1 sec) - 250

(2.5 sec).

Beep Tone

Tone Length

8. Press the [V/M] key to accept the first beep tone of the User Beep.

9. If you make a mistake, press the [BAND] key to back-space the cursor, then re-enter the correct beep tone or length.

10. Repeat steps 6 - 9 until you have completed the User Beep.

11. When there is a beep tone which you wish to delete, bring the cursor to that beep tone using the [BAND]/[V/M] key, then press the [MODE] key repeatedly until the “dEL ” notation appears in the Memory Channel Number display slot. Press and hold in the

[MODE] key for one second to delete that beep tone.

12. When you wish to add a beep tone into the beep tone strings, move the cursor to the desired place where you wish to enter the beep tone using the [BAND]/[V/M] key, then press the [MODE] key repeatedly untill the “InS ” notation is displayed in the

Memory Channel Number display slot. Press and hold in the [MODE] key for one second to add the beep tone.

38

C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3

VX-3R O

PERATING

M

ANUAL


PERATION


ELL

O

PERATION

13. Press and hold the [HM/RV] key for one second to delete all data after the current position that may have previously been stored in the User Beep.

14. When you have programmed User Beep, press the [TXPO] key momentarily to confirm the User Beep.

You may check your work by monitoring the programmed User Beep. To do this, repeat steps 1 - 4 above, then press the [F/W] key.

S

PLIT

T

ONE

O

PERATION

The VX-3R can be operated in a Split Tone configuration via the Set mode.


2. Rotate the DIAL knob to select Set Mode Item 81: SQSPLT .



Set Mode Item.

4. Rotate the DIAL knob to select “ON ” (to enable the Split Tone feature).


When the Split Tone feature is activated, you can see the following additional parameters after the “MESSAGE ” parameter while selecting the Set Mode Item 79: SQ TYP :

D CODE : DCS Encode only

(the “ ” icon will blink during operation)

T DCS : Encodes a CTCSS Tone and Decodes a DCS code

(the “ ” icon will blink and the “ ” icon will appear during operation)

D TONE : Encodes a DCS code and Decodes a CTCSS Tone

(the “ ” icon will appear and the “ ” icon will blink during operation)

Select the desired operating mode, from the selections shown above, within Set Mode Item

79: SQ TYP .

VX-3R O

PERATING

M

ANUAL

39


PERATION

T

ONE

C

ALLING

(1750 H

Z

)

If the repeaters in your country require a 1750-Hz burst tone for access (typically in Europe), you can set the MONI switch to serve as a “Tone Call” switch instead. To change the configuration of this switch, we again use the Set Mode to help us.


2. Rotate the DIAL knob to select Set Mode Item 47: M /T-CL .



Set Mode Item.

4. Rotate the DIAL knob to select “T-CALL ” on the display.


To access a repeater, press and hold in the MONI switch for the time specified by the repeater owner/operator. The transmitter will automatically be activated, and a 1750-Hz audio tone will be superimposed on the carrier. Once access to the repeater has been gained, you may release the MONI switch, and use the PTT switch for activating the transmitter thereafter.

40 VX-3R O

PERATING

M

ANUAL

M

EMORY

M

ODE

The VX-3R provides a wide variety of memory system resources. These include:

“Regular” Memory Channels, which include:

900 “Standard” memory channels, numbered “1 ” through “900 .”

99 “Frequency Skip Memories,” numbered “901 ” through “999 .”

11 “Home” channels, providing storage and quick recall of one prime frequency on each operating band.

50 sets of band-edge memories, also known as “Programmable Memory Scan” channels, labeled “L01 /U01 ” through “L50 /U50 .”

24 Memory Banks, labeled “b 1 ” through “b24 .” Each Memory Bank can be assigned up to 100 channels from the “regular” memory channels.

Special Memory Channels, which include:

One “Emergency Automatic ID (EAI)” Channel.

10 “Weather Broadcast” Channels.

57 VHF Marine Channels.

89 popular Short-wave Broadcast Station Memory Channels.

Standard Memory Channels

(900 channels)

Frequency Skip Memory Channels

(99 channels)

PMS Memory Channels

(50 Sets)

EAI Channel

(1 channel)

HOME Channels

(11 channels)

Weather Broadcast Channels

(10 channels)

VHF Marine Channels

(57 channels)

Short-wave Broadcast Station

Memory Channels

(89 channels)

VX-3R O

PERATING

M

ANUAL

41

M

EMORY

M

ODE (R

EGULAR

M

EMORY

C

HANNEL

O

PERATION

)

M

EMORY

S

TORAGE

1. Select the desired frequency while operating in the VFO mode. Be sure to set up any desired CTCSS or DCS tones, as well as any desired repeater offset. The power level may also be set at this time, if you wish to store it.

2. Press and hold in the [F/W] key for 1/2 seconds.

3. Within five seconds of releasing the [F/W] key, you need to make a decision regarding channel storage. The microprocessor will automatically select the next-available “free” channel (a memory register on which no data has been stored). If you do not wish to make a change and accept the “free” channel, proceed to step 4. If you wish to select a different channel number into which to store the data, rotate the DIAL knob to select the desired memory channel.


Advice: You may jump 100 memory channels, if you’re in a hurry (101 Æ 201 Æ 301 …), by pressing the [TXPO] key (multiple times, if necessary). Any channel that you see with a blinking channel number currently has no data written on it (i.e. the channel is

“free”).

4. Press the [F/W] key once more to store the frequency into memory.

5. You will still be operating in the “VFO” mode, so you may now enter other frequencies, and store them into additional memory locations, by repeating the above process.

1) You may change the automatic memory channel selection feature to select

the “next-highest memory channel above the last-stored memory channel” instead of the “next-available ‘free’ channel” via the Set Mode Item 50: MW

WMD; see page 114.

2) You may disable the memory write function which prevents a memory write operation if you should accidentally perform a wrong key sequence via the Set Mode Item 53:

MRPTCT. See page 114 for details. When the memory write protect is activated, the

“PROTCT” notation appears on the display while a memory write operation is being performed.

I

MPORTANT

N

OTE

On rare occasions the memorized data may become corrupted by miss operation, or static electricity. When repairs are made the memory data may be lost. Please write down or record the memorized information so you will be able to restore it if needed.

42 VX-3R O

PERATING

M

ANUAL

M

EMORY

M

ODE (R

EGULAR

M

EMORY

C

HANNEL

O

PERATION

)

M

EMORY

S

TORAGE

S

TORING

I

NDEPENDENT

T

RANSMIT

F

REQUENCIES

(“O

DD

S

PLITS

”)

All memories can store an independent transmit frequency, for operation on repeaters with non-standard shift. To do this:

1. Store the receive frequency using the method already described under MEMORY

STORAGE (it doesn’t matter if a repeater offset is active).

2. Turn to the desired transmit frequency, then press and hold in the [F/W] key for 1/2 second.

3. Within five seconds of releasing the [F/W] key, rotate the DIAL knob to select the same memory channel number as used in step “1” above.


4. Press and hold in the PTT switch, then press the [F/W] key once more momentarily while holding the PTT switch in (this does not key the transmitter).

Whenever you recall a memory which contains independently-stored transmit and receive frequencies, the

“ ” indication will appear in the display.

M

EMORY

R

ECALL

1. While operating in the VFO mode, press the [V/M] key to enter the Memory mode.

2. Rotate the DIAL knob to select the desired channel.


3. If you press the [F/W] key momentarily, then rotate the DIAL knob, the memory channel will be selected in 10 channels per step.

4. To return to the VFO mode, press the [V/M] key.

You may change the step of the fast channel selection mode ([F/W] key +

DIAL knob) via Set Mode Item 51: MRFSTP. See page 114 for details.

VX-3R O

PERATING

M

ANUAL

43

M

EMORY

M

ODE (R

EGULAR

M

EMORY

C

HANNEL

O

PERATION

)

HOME C

HANNEL

M

EMORY

A special one-touch “HOME” channel is available for each of the operating bands, to allow quick recall of a favorite operating frequency on each band.

H

OME

C

HANNEL

R

ECALL

1. Press the [F/W] key then press the [HM/RV] key to recall the Home Channel on the band group where you are currently operating.

2. Press the [F/W] key then press the [HM/RV] key again to return to the previous-used frequency (either a VFO or a memory channel).

USA V

ERSION

The transceiver switches to VFO mode if the DIAL knob is turned.

You may disable the above function (automatically switching to the VFO mode) via Set Mode Item 37:

HM>VFO.

EXP V

ERSION

H

OME

C

HANNEL

F

REQUENCY

C

HANGE

The factory defaults for the Home channels are listed below. You may re-program the

Home channel in a manner identical to that used for the regular memories:

1. Select the desired frequency, while operating in the VFO mode. Be sure to set up any desired CTCSS or DCS tones, as well as any desired repeater offset. The power level may also be set at this time, if you wish to store it.

2. Press and hold in the [F/W] key for 1/2 seconds.

3. While the memory channel number is blinking, just press the [HM/RV] key. The frequency and other data (if any) will now be stored in the special HOME channel register.

4. You may repeat this process on the other operating bands.

The UHF HOME channel is the one used during “Emergency” operation. See page 74 for details regarding this feature.

D

EFAULT

H

OME

C

HANNELS

O

PERATING

B

AND

[B

AND

N

UMBER

]

SW Band [1]

50 MHz Ham Band [2]

Air Band [3]


VHF-TV Band [5]



UHF-TV Band [8]


AM Broadcast Band [A]

FM Broadcast Band [F]

USA V

F

REQUENCY

ERSION

EXP V

ERSION

1.800 MHz

30.000 MHz

108.000 MHz

146.520 MHz

174.000 MHz

222.000 MHz

446.000 MHz

470.000 MHz

860.000 MHz

0.540 MHz

76.000 MHz

1.800 MHz

30.000 MHz

108.000 MHz

144.000 MHz

174.000 MHz

222.000 MHz

430.000 MHz

470.000 MHz

860.000 MHz

0.540 MHz

76.000 MHz

44 VX-3R O

PERATING

M

ANUAL

M

EMORY

M

ODE (R

EGULAR

M

EMORY

C

HANNEL

O

PERATION

)

L

ABELING

M

EMORIES

You may wish to append an alpha-numeric “Tag” (label) to a memory or memories, to aid in recollection of the channel’s use (such as a club name, etc.). This is easily accomplished using the Set Mode.

1. Recall the memory channel on which you wish to append a label.


3. Rotate the DIAL knob to select the Set Mode Item 52: MRNAME .



Set Mode Item.

5. Rotate the DIAL knob to select the first digit of the desired label.

6. Press the [V/M] key to move to the next character.

7. Repeat steps 5 and 6 to program the remaining letters, numbers, or symbols of the desired label. A total of six characters may be used in the creation of a label.

8. If you make a mistake, press the [BAND] key to back-space the cursor, then re-enter the correct letter, number, or symbol.

9. When you have completed the creation of the label, press the

PTT switch to save the label and return to memory mode with the alpha-numeric “Tag” (label) displayed.

You may check the frequency of the “Tagged” memory channel temporarily by pressing and holding the MONI switch.

Release the MONI switch to return to “Tag” display.

To disable the alpha-numeric Tag and enable the frequency display:

1. Set the VX-3R to the “MR” (Memory Recall) mode, and recall the memory channel on which you wish to disable the alpha-numeric Tag.


3. Rotate the DIAL knob to select the Set Mode Item 49: MR DSP .



Item’s setting.

5. Rotate the DIAL knob to set this Set Mode Item to “FREQ ” (thus disabling the alpha-numeric display).

6. Press the PTT switch to save the new setting and return to memory mode with frequency display.

VX-3R O

PERATING

M

ANUAL

45

M

EMORY

M

ODE (R

EGULAR

M

EMORY

C

HANNEL

O

PERATION

)

L

ABELING

M

EMORIES

To enable the alpha-numeric Tag (label) display again, just repeat the above procedure, rotating the DIAL knob to select “ALPHA ” in step 5 above.

You may set up some memory channels to have their frequencies displayed, while others may be set to have their Name Tag displayed. The selection within

Set Mode Item 49: MR DSP is not applied to all memory channels at once.

M

EMORY

O

FFSET

T

UNING

Once you have recalled a particular memory channel, you may easily tune off that channel, as though you were in the “VFO” mode.

1. With the VX-3R in the “MR” (Memory Recall) mode, select the desired memory channel.

2. Press the [F/W] key, then press the [V/M] key to activate the

“Memory Tuning” feature. The Memory Channel number will be replaced by “tun .”

3. Rotate the DIAL knob, as desired, to tune to a new frequency.

The synthesizer steps selected for VFO operation on the current band will be the steps used during Memory Tuning.


4. If you wish to return to the original memory frequency, just press the [V/M] key momentarily.

5. If you wish to store a new frequency set during Memory Tuning, just press and hold in the [F/W] key for 1/2 seconds, per normal memory storage procedure. The microprocessor will automatically set itself to the next-available clear memory location, and you then press [F/W] again to lock in the new frequency.

1) If you want to replace the original memory contents with those of the new frequency, be sure to rotate the DIAL knob to the original memory channel number!

2) Any required CTCSS/DCS changes, or repeater-offset modifications, must be done before storing the data into the new (or original) memory channel location.

46 VX-3R O

PERATING

M

ANUAL

M

EMORY

M

ODE (R

EGULAR

M

EMORY

C

HANNEL

O

PERATION

)

M

ASKING

M

EMORIES

There may be situations where you want to “Mask” memories so they are not visible during memory selection or scanning. For example, several memories used only in a city you visit infrequently may be stored, then “Masked” until you visit that city, at which time you can

“Unmask” them for normal use.

1. Press the [V/M] key, if needed, to enter the MR mode.

2. Press and hold in the [F/W] key for 1/2 seconds, then rotate the

DIAL knob to select the memory channel to be “Masked” from view.


3. Press the [ ] key. The confirmation massage (M-DEL?

) will appear on the display. Press the [F/W] key to cancel the Masking

Memory procedure, if desired.

4. Press the [ ] key once more. The display will revert to memory channel #1. If you rotate the DIAL knob to the location you just “Masked,” you will observe that it is now invisible.

To Unmask the hidden memory, repeat the above procedure. Press and hold in the [F/W] key for 1/2 seconds, rotate the DIAL knob to select the masked memory’s number, then press the [ ] key to restore the memory channel’s data.

Watch out! You can manually store data over a “Masked” memory, deleting previous data, if you’re not careful. Use the “next available memory” technique storage technique to avoid over-writing a masked memory.

VX-3R O

PERATING

M

ANUAL

47

M

EMORY

M

ODE (R

EGULAR

M

EMORY

C

HANNEL

O

PERATION

)

M

EMORY

B

ANK

O

PERATION

The large number of memories available in the VX-3R could be difficult to utilize without some means of organizing them. Fortunately, the VX-3R includes provision for dividing the memories into as many as 24 Memory Groups, so you can categorize the memories in a manner convenient to you. You may enter and exit the “Memory Group” mode by a single press of the [BAND] key, as we shall see below.

A

SSIGNING

M

EMORIES TO A

M

EMORY

B

ANK

1. Recall the memory channel to be assigned to a Memory Bank.

2. Press and hold in the [F/W] key for 1/2 seconds, then rotate the

DIAL knob to select the Memory Bank number you want as the

Memory Bank for this channel (“b 1 ” ~ “b24 ,” which is found before memory channel “1 ”).


3. Press the [F/W] key momentarily.

4. At this point, the memory channel data is copied into the Memory Bank.

Memory Channel

CH 1 145.000 MHz

CH 2 145.500 MHz

CH 3 435.000 MHz

CH 4 435.500 MHz

CH 5 145.800 MHz

CH 6 436.000 MHz

CH 7 128.800 MHz

Memory Bank “1”

144 MHz Amateur Band Channels


430 MHz Amateur Band Channels


All Amateur Band Channels

1) You may assign one memory chan-


Club Channels nel into several

Memory Banks.

CH 897 145.620 MHz

CH 898 436.780 MHz

CH 899 128.600 MHz


Air Band Channels

2) The PMS memory channels (L1/U1 through L50/U50) may not be assigned to a

Memory Bank.

M

EMORY

B

ANK

R

ECALL


2. Press the [BAND] key to activate the “Memory Bank” mode.

The “ ” icon and Memory Bank number will appear on the display.

3. Press the [F/W] key, and then press the [BAND] key.

1 ” through “BANK 24 ”).


5. Press the [BAND] key. Now, as you rotate the DIAL knob to select memories, you will observe that you can only select memory channels in the current memory bank.

48 VX-3R O

PERATING

M

ANUAL

M

EMORY

M

ODE (R

EGULAR

M

EMORY

C

HANNEL

O

PERATION

)

M

EMORY

B

ANK

O

PERATION

6. To change to another Memory Bank, press the [F/W] key, then press the [BAND] key. Now rotate the DIAL knob to select the new Memory Bank, then press the [BAND] key again.

7. To exit from Memory Bank operation, just press the [BAND] key. The “ ” icon will disappear from the display, that you are now in the “regular” Memory Recall mode, without utilization of the Memory Banks. The memories stored in the various

Banks will remain in those banks. You do not need to store them again.

R

EMOVING

M

EMORIES FROM A

M

EMORY

B

ANK

1. Recall the memory channel to be removed from a Memory Bank.

2. Press and hold the [F/W] key for one second, then press the [ ] key to remove the memory channel data from the Memory bank.

C

HANGING A

M

EMORY

B

ANK ’ S

N

AME

You may change the default Memory Bank Names, which are shown on the display while selecting the Memory Bank your desire.


2. Rotate the DIAL knob to select the Set Mode Item labeled 11:

BNK.NAM

.


3. Press the [TXPO] key momentarily to enable adjustment of this Set Mode Item.

4. Rotate the DIAL knob to select the memory bank on which you wish to change a label.

5. Press the [TXPO] key momentarily to enable changing of the name tag.



8. Repeat steps 6 and 7 to program the remaining letters, numbers, or symbols of the desired label. A total of six characters may be used in the creation of a label.

9. If you make a mistake, press the [BAND] key to backspace the cursor, then re-enter the correct letter, number, or symbol.

10. When you have completed the changes of the label, press the PTT switch to save the label and exit.

VX-3R O

PERATING

M

ANUAL

49

M

EMORY

M

ODE (R

EGULAR

M

EMORY

C

HANNEL

O

PERATION

)

M

OVING

M

EMORY

D

ATA TO THE

VFO

Data stored on memory channels can easily be moved to the VFO, if you like.

1. Select the memory channel containing the frequency data to be moved to VFO.

2. Press and hold in the [F/W] key for one second, then press the

[V/M] key. The confirmation massage (V-WRT?

) will appear on the display. Press the [F/W] key to cancel the Moving Memory

Data procedure, if desired.

3. Press the [V/M] key once more. The data will now have been copied to the VFO, although the original memory contents will remain intact on the previously stored channel.

If a Split Frequency Memory channel was transferred, the Tx frequency will be ignored (you will be set up for Simplex operation on the Receive frequency).

M

EMORY

O

NLY

M

ODE

Once memory channel programming has been completed, you may place the radio in a

“Memory Only” mode, whereby VFO operation is impossible. This may be particularly useful during public-service events, where a number of operators may be using the radio for first time, and ultimate simplicity of channel selection is desired.

To place the radio into the Memory Only mode, turn the radio off. Now press and hold in the [V/M] key while turning the radio on. To return to normal operation, repeat the above power-on procedure.

50 VX-3R O

PERATING

M

ANUAL

M

EMORY

M

ODE (S

PECIAL

M

EMORY

C

HANNEL

O

PERATION

)

The VX-3R provides Special Memory Channels, which made up of:

10 “Weather Broadcast” Channels.

281 VHF Marine Channels

89 popular Short-wave Broadcast Station Memory Channels.

You may assign the Special Memory Channels to a Memory Bank. See page 48 regarding Memory Bank Operation for details.

W

EATHER

B

ROADCAST

C

HANNELS

The VHF Weather Broadcast Station Memory Channel Bank has been pre-programmed at the factory, for quick selection of NOAA weather information stations.

1. Press the [F/W] key, then press the [ ] key, to recall the Special Memory Menu.

CH ” (thus recalling the Weather Broadcast Memory Bank).

3. Rotate the DIAL knob to select the desired Weather Broadcast channel.


4. If you wish to scan this bank to search for louder stations, just press the PTT switch. When the scanner pauses on a station, press the PTT switch once to halt the scan, or press it twice to restart the scan.

5. To exit to normal operation, press the [V/M] key, or press [F/W] key followed by the [ ] key.

CH

1

2

3

4

5

F

REQUENCY

162.550 MHz

162.400 MHz

162.475 MHz

162.425 MHz

162.450 MHz

CH

6

7

8

9

10

F

REQUENCY

162.500 MHz

162.525 MHz

161.650 MHz

161.775 MHz

163.275 MHz

1) In the event of extreme weather disturbances, such as storms and hurricanes, the NOAA (National Oceanic and Atmospheric Administration) sends a weather alert accompanied by a 1050 Hz tone and subsequent weather report on one of the NOAA weather channels. You may disable the Weather Alert tone via Set Mode Item 93: WX ALT, if desired. See page 122.

2) You may append and display an alpha-numeric “Tag” (label) to a Weather Broadcast channel or channels. See page 45 regarding the labeling of a memory for details.

VX-3R O

PERATING

M

ANUAL

51

M

EMORY

M

ODE (R

EGULAR

M

EMORY

C

HANNEL

O

PERATION

)

11

12

13

14

7

8

9

10

5

6

3

4

CH

No.

1

2

VHF M

ARINE

C

HANNELS

Another special Memory Bank contains VHF Marine Channels, pre-programmed at the factory, for quick selection.


2. Press the [BAND] key, repeatedly if necessary, to select “INTVHF ”

(thus recalling the Marine Channel Memory Bank).

3. Rotate the DIAL knob to select any of 57 available VHF Marine

Channels.


4. Press the [HM/RV] key to monitor the opposite frequency while recalling the semi-duplex channel (such as Channel “1”). Press the [HM/RV] key again to revert to normal monitoring.

5. To exit to normal operation, press the [V/M] key, or press [F/W] key followed by the

[ ] key.

F

REQUENCY

(MHz)

156.050

160.650

156.100

160.700

156.150

160.750

156.200

160.800

156.250

160.850

156.300

156.350

160.950

156.400

156.450

156.500

156.550

156.600

156.650

156.700

25

26

27

28

21

22

23

24

17

18

19

20

CH

No.

15

16

VHF M

ARINE

C

HANNEL

F

REQUENCY

L

IST

F

REQUENCY

(MHz)

156.750

156.800

156.850

156.900

161.500

156.950

161.550

157.000

161.600

157.050

161.650

157.100

161.700

157.150

161.750

157.200

161.800

157.250

161.850

157.300

161.900

157.350

161.950

157.400

162.000

70

71

72

73

66

67

68

69

CH

No.

60

61

62

63

64

65

F

REQUENCY

(MHz)

156.025

160.625

156.075

160.675

156.125

160.725

156.175

160.775

156.225

160.825

156.275

160.875

156.325

160.925

156.375

156.425

156.475

156.525

156.575

156.625

156.675

84

85

86

87

88

80

81

82

83

76

77

78

79

CH

No.

74

75

F

REQUENCY

(MHz)

156.725

156.775

156.825

156.875

156.925

161.525

156.975

161.575

157.025

161.625

157.075

161.675

157.125

161.725

157.175

161.775

157.225

161.825

157.275

161.875

157.325

161.925

157.375

161.975

157.425

162.025

52 VX-3R O

PERATING

M

ANUAL

M

EMORY

M

ODE (S

PECIAL

M

EMORY

C

HANNEL

O

PERATION

)

S

HORT

-W

AVE

B

ROADCAST

S

TATION

M

EMORY

C

HANNELS

A large number of Short-Wave Broadcast Station Memory Channels have also been preprogrammed at the factory, for convenient selection of broadcast stations.


2. Press the [BAND] key to select “RADIO ” (thus recalling the

Broadcast Station Channel Memory Bank).

3. Rotate the DIAL knob to select any of 89 available Broadcast

Stations.


4. Press and hold the MONI switch to display the receiving frequency ”Station’s Frequency” (and disabling the squelch). Release the MONI switch to return to “Station Name” display.

5. To exit to normal operation, press the [V/M] key, or press [F/W] key followed by the [ ] key.

Tag

DW

DW

DW

DW

ITALY

ITALY

ITALY

ITALY

TURKEY

TURKEY

TURKEY

TURKEY

VATICN

VATICN

VATICN

VATICN

VOA

VOA

VOA

VOA

CANADA

CANADA

CANADA

CANADA

BBC

BBC

BBC

BBC

FRANCE

FRANCE

FRANCE

FRANCE

NEDERL

NEDERL

NEDERL

NEDERL

CZECH

CZECH

CZECH

CZECH

PORTUG

PORTUG

PORTUG

PORTUG

MODE

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

11.670

15.195

6.000

6.075

9.650

9.735

5.990

9.575

9.675

17.780

7.170

7.270

9.560

11.690

9.660

11.625

Freq.

(MHz)

6.030

6.160

9.760

11.965

9.555

9.600

11.715

11.955

6.195

9.410

12.095

15.310

6.090

9.790

11.830

15235

5.955

6.020

9.895

11.655

5.985

7.165

9.455

11.860

9.780

11.630

15.550

21.655

27

28

29

30

23

24

25

26

19

20

21

22

15

16

17

18

11

12

13

14

7

8

9

10

5

6

3

4

Ch

No.

1

2

39

40

41

42

43

44

35

36

37

38

31

32

33

34

Station Name

Voice of America

Voice of America

Voice of America

Voice of America

Radio Canada International




British Broadcasting Corporation




Radio France International




Deutsche Welle

Deutsche Welle

Deutsche Welle

Deutsche Welle

Italian Radio International




Voice of Trukey

Voice of Trukey

Voice of Trukey

Voice of Trukey

Vatican Radio

Vatican Radio

Vatican Radio

Vatican Radio

Radio Nederland

Radio Nederland

Radio Nederland

Radio Nederland

Radio Liberty

Radio Liberty

Radio Liberty

Radio Liberty

Radio Portugal

Radio Portugal

Radio Portugal

Radio Portugal

B

ROADCAST

S

TATION

F

REQUENCY

L

IST

71

72

73

74

67

68

69

70

63

64

65

66

59

60

61

62

55

56

57

58

51

52

53

54

47

48

49

50

Ch

No.

45

46

83

84

85

86

87

88

89

79

80

81

82

75

76

77

78

MODE

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

AM

9.560

11.755

15.400

5.920

5.940

7.200

12.030

7.465

11.585

15.615

17.535

6.045

9.595

11.620

15.020

7.160

Freq.

(MHz)

9.650

11.880

11.910

15.290

6.055

7.315

9.590

9.925

9.985

6.065

9.490

15.240

17.505

6.120

7.190

9.785

11.685

6.135

7.275

9.570

13.670

6.165

7.200

9.750

11.860

5.995

9.580

9.660

12080

Tag

FINLAN

RUSSIA

RUSSIA

RUSSIA

RUSSIA

ISRAEL

ISRAEL

ISRAEL

ISRAEL

INDIA

INDIA

INDIA

INDIA

CHINA

CHINA

CHINA

SPAIN

SPAIN

SPAIN

SPAIN

NIKKEI

NORWAY

NORWAY

NORWAY

NORWAY

SWEDEN

SWEDEN

SWEDEN

SWEDEN

FINLAN

FINLAN

FINLAN

CHINA

KOREA

KOREA

KOREA

KOREA

JAPAN

JAPAN

JAPAN

JAPAN

AUSTRA

AUSTRA

AUSTRA

AUSTRA

VX-3R O

PERATING

M

ANUAL

Station Name

Radio Exterior de Espana




Radio Nikkei

Radio Norway International




Radio Sweden

Radio Sweden

Radio Sweden

Radio Sweden

Radio Finland

Radio Finland

Radio Finland

Radio Finland

Voice of Russia

Voice of Russia

Voice of Russia

Voice of Russia

Israel Broadcasting Authority




All India Radio (AIR)




China Radio International (CRI)




Radio Korea

Radio Korea

Radio Korea

Radio Korea

Radio Japan

Radio Japan

Radio Japan

Radio Japan

Radio Australia

Radio Australia

Radio Australia

Radio Australia

53

S

CANNING

The VX-3R allows you to scan just the memory channels, the entire operating band, or a portion of that band. It will halt on signals encountered, so you can talk to the station(s) on that frequency, if you like.

Scanning operation is basically the same in each of the above modes. Before you begin, take a moment to select the way in which you would like the scanner to resume scanning after it halts on a signal.

S

ETTING THE

S

CAN

-R

ESUME

M

ODE

Eleven options for the Scan-Resume mode are available:

2 SEC - 10 SEC : In this mode, the scanner will halt on a signal it encounters, and will hold there for the selected resume time. If you do not take action to disable the scanner within that time period, the scanner will resume even if the

BUSY : stations are still active.

In this mode, the scanner will halt on a signal it encounters. When the carrier has dropped because the other station(s) ceased transmission, the scanner will resume. In the case of constant-carrier signals like Weather

HOLD :

Station broadcasts, the scanner will likely remain on this frequency indefinitely. The Scan Re-start Delay time (default interval: 2 seconds) is set by the Set Mode Item 76: SCN.STR

.

In this mode, the scanner will halt on a signal it encounters. It will not restart automatically; you must manually re-initiate scanning if you wish to resume.

To set the Scan-Resume mode:


2. Rotate the DIAL knob to select Set Mode Item 75: SCN.RSM

.



Set Mode Item.

4. Rotate the DIAL knob to select the desired scan-resume mode described above.

5. When you have made your selection, press the PTT switch to save the new setting and exit to normal operation.

The default condition for this Set Mode Item is “5 SEC.”

54 VX-3R O

PERATING

M

ANUAL

S

CANNING

To set the Scan-Restart Delay Time:


2. Rotate the DIAL knob to select Set Mode Item 76: SCN.STR

.



Set Mode Item.

4. Rotate the DIAL knob to select the desired Scan-Restart Delay

Time. Available selections are 100 - 900 MS (100 MS/step) and 1 - 10 SEC (0.5 SEC/step).

5. When you have made your selection, press the PTT switch to save the new setting and exit to normal operation.

The default condition for this Set Mode Item is “2 SEC.”

VX-3R O

PERATING

M

ANUAL

55

S

CANNING

VFO S

CANNING

This mode allows you to scan on the VFO mode.

1. Select the VFO mode by pressing the [V/M] key, if necessary.

2. Press and hold in the [BAND] key for one second, and rotate the

DIAL knob while holding in the [BAND] key to select the bandwidth for the VFO scanner. Available selections are ±1 MHz ,

±2 MHz , ±5 MHz , BAND , ALL PMS-X .

±1 MHz , ±2 MHz ±5 MHz : The scanner will sweep frequencies within the selected

BAND

ALL :

PMS-X

:

: bandwidth.

The scanner will sweep frequencies only on the current band.

The scanner will sweep all frequencies between 1.8

MHz and 999.99 MHz (except the FM Broadcast Band:

76 - 107 MHz).

The scanner will sweep frequencies within the currently-selected PMS frequency pair. See page 61 for details.


3. Release the [BAND] key to start scanning.

4. When the scanner encounters a signal strong enough to open the squelch, the scanner will halt temporarily; the decimal point of the frequency display will blink during this

“Pause” condition.

5. The scanner will then resume according to the Scan-Resume mode selected in the previous section.

6. To cancel scanning, press the PTT switch or [V/M] key.

1) When you start scanning, the VX-3R will be changing frequency in the upward direction. If you want to change direction of the scan while it is underway, rotate the DIAL knob one click in the opposite direction (in this case, one click counter-clockwise). You’ll see the scanner turn around and change frequency downward!

2) You may change the scanner’s method of operation so the VFO frequency will jump

to the low band edge of the next band when the VFO frequency reaches the high edge of

the current band (or vice versa). See page 121 regarding Set Mode Item 90: VFO MD.

56 VX-3R O

PERATING

M

ANUAL

S

CANNING

VFO S

CANNING

H

OW TO

S

KIP

(O

MIT

)

A

F

REQUENCY DURING

VFO S

CAN

If the VFO scan stops on a frequency or frequencies that you do not need (such as a spurious radiation from a television), such frequencies can be “skipped” during VFO scanning.

A special “Frequency Skip Memory” bank is reserved to store these frequencies.

To skip a frequency during VFO scanning:

1. While VFO scanning is stopped on the frequency that you do not need, press and hold the [F/W] key for 1/2 seconds, then rotate the DIAL knob to select the desired Frequency Skip Memory channel (901 - 999 ). The microprocessor will automatically select the next-available “free” Frequency Skip Memory channel (a memory register on which no data has been stored). If you see that any blinking channel number, it means that the channel currently has no data written on it (i.e. the channel is “free”).


2. Press the [F/W] key to store the frequency into the Frequency Skip Memory. It will now be ignored during VFO scanning.

To re-institute a frequency into the VFO scan loop:


2. Press and hold in the [F/W] key for 1/2 second, then rotate the DIAL knob to select the memory channel to be re-instituted.


3. Press the [ ] key to delete the channel from the Frequency Skip Memory; this will restore the frequency into the VFO scan loop.

The VX-3R has 99 VFO Frequency Skip Memory Channels.

S

ETTING THE

S

QUELCH

L

EVEL DURING ACTIVE

S

CANNING OPERATION

The VX-3R allows adjustment of the Squelch level “on the fly” while you are scanning.

1. While the scanner is engaged, press the [F/W] key. Then press the [MONI] key (the current squelch level will appear in the Memory

Channel Number display slot in the frequency display).

2. Rotate the DIAL to select the desired Squelch level.

Note: Do not forget to pull the DIAL knob to rotate the

DIAL knob.

3. Press the PTT switch momentarily to save the new setting and exit to normal operation. In this case, pressing the PTT switch this one time will not cause scanning to stop.

VX-3R O

PERATING

M

ANUAL

57

S

CANNING

M

EMORY

S

CANNING

Memory scanning is also easy to initiate:

1. Set the radio to the Memory mode by pressing the [V/M] key, if necessary.


DIAL knob while holding in the [BAND] key to select the desired Memory Scan mode. Available selections are ALL CH ,

TAG1 , TAG2 , BAND , and PMS-X .

ALL CH : The scanner sweeps all Memory channels.

TAG1 : The scanner sweeps only those Memory channels with the same first digit of the alpha/numeric tag as the first channel on which scanning started.

TAG2 : The scanner sweeps only those Memory channels with the same first and second digits of the alpha/numeric tag as the first channel on which scanning started.

BAND : The scanner sweeps only those Memory channels which are memorized on the same operating band as the first channel on which scanning started.

PMS-X : The scanner will sweep frequencies within the currently-selected PMS frequency pair. See page 61 for details.


3. Release the [BAND] key to initiate scanning.

4. As with VFO scanning, the scanner will halt on any signal encountered that is strong enough to open the squelch; it will then resume scanning according to the Scan-Resume mode set previously. When there are no memory channels corresponding to the selected Memory Scan mode, the “MS ERR ” notation will appear on the display.

5. To cancel scanning, press the PTT switch or [V/M] key.

58 VX-3R O

PERATING

M

ANUAL

S

CANNING

M

EMORY

S

CANNING

H

OW TO

S

KIP

(O

MIT

)

A

C

HANNEL DURING

M

EMORY

S

CAN

O

PERATION

As mentioned previously, some continuous-carrier stations like a Weather Broadcast station will seriously impede scanner operation if you are using the “Carrier Drop” Scan-

Resume mode, as the incoming signal will not pause long enough for the transceiver to resume scanning. Such channels may be “Skipped” during scanning, if you like:

1. Recall the Memory Channel to be skipped during scanning.

2. Press and hold the [TXPO] key for one second to enter the Set mode.

3. Rotate the DIAL knob to select the Set Mode Item 54: MRSKIP .



Set Mode Item.

5. Rotate the DIAL knob so as to select “SKIP .” The current Memory

Channel will now be ignored during scanning. The “ONLY ” selection is used for “Preferential Memory Scan,” described in the next column.

6. When you have made your selection, press the PTT switch to save the setting and exit to normal operation.

When you recall the “skipped” memory channel manually, a small

“

X

” icon will appear at the above of the volume level indicator, indicating it is to be ignored during scanning.

To re-institute a channel into the scanning loop, select “OFF ” in step 5 above (the “Skipped” channel will, of course, still be accessible via manual channel selection methods using the

DIAL knob in the MR mode, whether or not it is locked out of the scanning loop).

One Touch Memory Skip

If the scanner repeatedly stops on a channel due to temporary noise or interference while

Memory Channel Scan is activated, it is a simple operation to mark it to be skipped (except for Memory Channel “1”).

To skip a channel temporarily, press the [F/W] key, and then press the [V/M] key while the scanner has stopped on the channel to be skipped. The scanner will immediately resume, and that channel will be assigned to the “skipped” memory channel.

To re-institute a channel into the scanning loop, perform the “How to Skip (Omit) a Channel during Memory Scan Operation” described previously, then select “OFF ” in step 5.

VX-3R O

PERATING

M

ANUAL

59

S

CANNING

M

EMORY

S

CANNING

P

REFERENTIAL

M

EMORY

S

CAN

The VX-3R also allows you to set up a “Preferential Scan List” of channels which you can

“flag” within the memory system. These channels are designated by a blinking “ X ” icon when you have selected them, one by one, for the Preferential Scan List.

When you initiate memory scanning, the scan begins on a channel with the blinking “

X

” icon appended; only those channels bearing the blinking “ X ” icon will be scanned. If you initiate scanning on a channel that does not have the blinking “

X

” icon appended, you will scan all channels including those with the blinking “ X ” icon appended.

Here is the procedure for setting up and using the Preferential Scan List:

1. Recall the Memory Channel, which you wish to add to the Preferential Scan List.


3. Rotate the DIAL knob to select Set Mode Item 54: MRSKIP .



Set Mode Item.

5. Rotate the DIAL knob to select “ONLY .”

6. When you have made your selection, press the PTT switch to save the settings and exit to normal operation.

To initiate Preferential Memory Scan:

1. Press the [V/M] key momentarily to enter the Memory Recall mode, if you are not using memories already.

2. Rotate the DIAL to select any channel which has a blinking “

X

” icon appended to the channel number.



DIAL knob while holding in the [BAND] key, to select the desired Memory Scan mo2de.

ALL CH : The scanner sweeps all Memory channels.

TAG1 : The scanner sweeps only those Memory channels with the same first digit of the alpha/numeric tag as the first channel on which scanning started.

TAG2 : The scanner sweeps only those Memory channels with the same first and second digits of the alpha/numeric tag as the first channel on which scanning started.

BAND : The scanner sweeps only those Memory channels which are memorized on the same operating band as the first channel on which scanning started.

PMS-X : The scanner will sweep frequencies within the currently-selected PMS fre-

60 VX-3R O

PERATING

M

ANUAL

S

CANNING

M

EMORY

S

CANNING quency pair. See next chapter for details.

5. Release the [BAND] key to initiate Preferential Memory Scanning. Only the channels that have a blinking “

X

” icon appended to the channel number will be scanned.

M

EMORY

B

ANK

S

CAN

When the Memory Bank feature is engaged, the scanner sweeps only memory channels in the current Memory Bank. However, if the Memory Bank Link Scan feature is enabled, you may sweep the memory channels in several Memory Banks which you have selected.

To enable the Memory Bank Link Scan feature:

1. Set the radio to the Memory mode by pressing the [V/M] key, if necessary.

2. Press the [BAND] key to activate the “Memory Bank” mode.

The “ display.

” icon and Memory Bank number will appear on the

3. Press the [F/W] key, followed by the [BAND] key.

1 ” ~ “BANK24 ”) you wish to sweep using Memory Bank Link

Scan.

5. Press the [V/M] key momentarily. A small blinking “ X ” icon will appear at the above of the volume level indicator, indicating this

Memory Bank will now be swept during Memory Bank Scan.

6. Repeat steps 4 and 5 above, to append the blinking “

X

” icon to any other Memory Banks you wish to sweep.

7. Press the [BAND] key.

8. Now, press and hold in the [BAND] key for one second to initiate the Memory Bank Link Scan.

9. To remove a Memory Bank from the Memory Bank Link Scan, repeat steps 1 - 5 above, to delete the blinking “

X

” icon from the

Memory Bank number indication.

VX-3R O

PERATING

M

ANUAL

61

S

CANNING

P

ROGRAMMABLE

(B

AND

L

IMIT

) M

EMORY

S

CAN

(PMS)

This feature allows you to set sub-band limits for either scanning or manual VFO operation. For example, you might wish to set up a limit (in North America) of 144.300 MHz to

148.000 MHz, to prevent encroachment into the SSB/CW “Weak Signal” portion of the band below 144.300 MHz. Here’s how to do this:

1. Set the radio to the VFO mode by pressing the [V/M] key, if necessary.

2. Using the techniques learned earlier in the above procedures, store 144.300 MHz into

Memory Channel #L1 (the “L” designates the Lower sub-band limit).

3. Likewise, store 148.000 MHz into Memory Channel #U1 (the “U” designates the

Upper sub-band limit).

4. Set the radio to the Memory mode by pressing the [V/M] key.

5. Press and hold in the [BAND] key for one second and rotate the

DIAL knob while holding in the [BAND] key to select the desired PMS frequency pair (PMSxx ). Then release the [BAND] key to initiate the Programmable (Band Limit) Memory Scan.

The Memory Channel number will be replaced by “Pxx ”. Tuning and scanning will now be limited within the just-programmed range.


6. 50 pairs of Band Limit memories, labeled L1 /U1 through L50 /U50 are available. You therefore can set upper and lower operation limits on a number of bands, if you like.

62 VX-3R O

PERATING

M

ANUAL

S

CANNING

P

RIORITY

C

HANNEL

S

CANNING

(D

UAL

W

ATCH

)

The VX-3R’s scanning features include a two-channel scanning capability, which allows you to operate on a VFO or Memory channel, while periodically checking a user-defined

Memory Channel for activity. If a station is received on the Memory Channel which is strong enough to open the Squelch, the scanner will pause on that station in accordance with the Scan-Resume mode set via Set Mode Item 75: SCN.RSM

. See page 54.

Here is the procedure for activating Priority Channel Dual Watch operation:

1. Press the [V/M] key momentarily to enter the Memory Recall mode, if you are not using memories already.

2. Press and hold in the [F/W] key for one second, then rotate DIAL knob to select the memory channel you wish to be the “Priority” channel.


3. Press the [BAND] key. The “PRI” icon will appear above of the volume level indicator, indicating it is the Priority channel.

4. Now set the VX-3R for operation on another memory channel, or on a VFO frequency.

5. Press and hold in the [V/M] key for one second. The display will remain on the VFO or memory channel selected. However, the “DW” icon will appear on the display, and every five seconds the VX-3R will check the

Priority Channel for activity. If a station appears on the Priority

Channel, the radio will pause on that channel, as described previously.

The receiving time interval (ratio) between the current channel (or VFO frequency) and

Priority channel may be customized via Set Mote Item 65: PRI.TMR

.

To set the receiving time interval:


2. Rotate the DIAL knob to select Set Mode Item 65: PRI.TMR

.



Set Mode Item.

4. Rotate the DIAL knob to select the desired time interval. Available selections are 0.1S

- 0.5S

(0.5S/step) and 1.0S

- 10S (0.5S/ step).


The default condition for this Set Mode Item is “5.0S.”

VX-3R O

PERATING

M

ANUAL

63

S

CANNING

P

RIORITY

C

HANNEL

S

CANNING

(D

UAL

W

ATCH

)

P

RIORITY

R

EVERT

M

ODE

During Priority channel operation (Dual Watch), a special feature is available which will allow you to move to the Priority Channel instantly, without waiting for activity to appear on the Priority Channel.

When this feature is enabled, and priority monitoring is engaged, just press the microphone’s

PTT switch. Operation will instantly revert to the Priority Channel.

To enable Priority Revert operation:


2. Rotate the DIAL knob to select Set Mode Item 64: PRI.RVT

.



Set Mode Item.

4. Rotate the DIAL knob so as to select “ON .”

5. When you have made your selection, press the PTT switch to save the settings and exit to normal operation.

To disable Priority Revert operation, select “OFF ” in step 4 above.

64 VX-3R O

PERATING

M

ANUAL

S

CANNING

A

UTOMATIC

L

AMP

I

LLUMINATION ON

S

CAN

S

TOP

The VX-3R will automatically illuminate the LCD Lamp whenever the scanner stops on a signal; this allows you to see the frequency of the incoming signal better at night. Note that this will, of course, increase the battery consumption, so be sure to switch it off during the day (the default condition for this feature is “ON ”).

The procedure for disabling the Scan Lamp is:


2. Rotate the DIAL knob to select Set Mode Item 74: SCN.LMP

.



Set Mode Item.

4. Rotate the DIAL knob to set this Set Mode Item to “OFF .”


B

AND

E

DGE

B

EEPER

The VX-3R will automatically “beep” when a band edge is encountered during scanning

(either in standard VFO scanning or during PMS operation). You may enable this feature

(band edge beeper) when the frequency reaches the band edge while selecting the VFO frequency by the DIAL knob.

The procedure for enabling the Band-Edge Beeper is:


2. Rotate the DIAL knob to select Set Mode Item 12: BP EDG .



Set Mode Item.

4. Rotate the DIAL knob to set this Set Mode Item to “ON .”


VX-3R O

PERATING

M

ANUAL

65

S

MART

S

EARCH

O

PERATION

The Smart Search feature allows you to load frequencies automatically where activity is encountered by your radio. When Smart Search is engaged, the transceiver will search above and below your current frequency, storing active frequencies as it goes (without stopping on them even momentarily). These frequencies are stored into a special Smart

Search memory bank, consisting of 31 memories (15 above the current frequency, 15 below the current frequency, plus the current frequency itself).

Two basic operating modes for Smart Search are available:

SINGLE : In this mode, the transceiver will sweep the current band once in each direction starting on the current frequency. All channels where activity is present will be loaded into the Smart Search memories, whether or not all 31 memories are filled. The search will stop after one sweep in each direction.

CONT : In this mode, the transceiver will make one pass in each direction as with One-

Shot searching. However, if all 31 channels are not filled after the first sweep, the radio will continue sweeping until they are all filled.

S

ETTING THE

S

MART

S

EARCH

M

ODE


2. Rotate the DIAL knob to select Set Mode Item 71: S SRCH .



Set Mode Item.

4. Rotate the DIAL knob to select the desired Smart Search mode

(see above).


66 VX-3R O

PERATING

M

ANUAL

S

MART

S

EARCH

O

PERATION

S

TORING

S

MART

S

EARCH

M

EMORIES

1. Set the radio to the VFO mode. Be sure that you have the Squelch adjusted properly (so that band noise is quieted).

2. Rotate the DIAL, while pressing and holding in the [MODE] key, to select the “S SRCH (Smart Search) Mode.”


3. Release the [MODE] key to enter the Smart Search mode.

4. Press and hold the [BAND] key for one second to begin the Smart Search scanning.

5. As active channels are detected, you will observe the number of “loaded” channels increasing in the regular memory channel window.

6. Depending on the mode you set for Smart Search operation

(“SINGLE ” or “CONT ”), the Smart Search scan will eventually terminate, and the LCD will revert to Smart Search Memory

Channel “C .”

7. To recall the Smart Search memories, rotate the DIAL knob to choose from among the

Smart Search memories.

8. To return to normal operation, just press the [MODE] key.

Smart Search is a great tool when visiting a city for the first time. You don’t need to spend hours looking up repeater frequencies from a reference guidebook…just ask your VX-3R where the action is!

VX-3R O

PERATING

M

ANUAL

67

C

HANNEL

C

OUNTER

O

PERATION

The Channel Counter allows measuring of the frequency of a nearby transmitter, without knowing that frequency in advance. The frequency can be measured by bringing the VX-

3R close to the transceiver which is transmitting.

The VX-3R performs a high-speed search within a ±5 MHz range from the frequency displayed on the LCD. When the strongest signal in that range is identified, the VX-3R displays the frequency of that (strongest) signal, and writes it into the special “Channel

Counter” memory.

Note: This Channel Counter is designed to provide an indication of the operating frequency of the incoming signal, one that is close enough to allow the user, thereafter, to tune precisely to the other station’s frequency. This feature is not, however, designed to provide a precise determination of the other station’s frequency.

1. Set the radio to the VFO mode in the predicted frequency range for the transmitter to be measured.

2. Bring the VX-3R into close proximity to the transmitter to be measured.

3. Rotate the DIAL, while pressing and holding in the [MODE] key, to select the “CH CNT (Channel Counter) mode.”


4. Release the [MODE] key to begin the Channel Counter; the frequency of the nearby station will be displayed. When the channel counter is active, a 50 dB receiver front-end attenuator will be engaged. Therefore, only stations in close proximity may have their frequencies measured using this feature.

5. If it isn’t possible to determine the signal’s frequency, the transceiver will return to the frequency on which you were operating when you started Channel Counter operation.

6. When you are finished, just press the [MODE] key. The radio will exit from Channel

Counter operation.

68 VX-3R O

PERATING

M

ANUAL

C

HANNEL

C

OUNTER

O

PERATION

S

ETTING THE

C

HANNEL

C

OUNTER

S

WEEP

W

IDTH

You may change the bandwidth of the Channel Counter. Available selections are ±5, ±10,

±50, and ±100 MHz (default: ±5 MHz).

Here is the procedure for setting the Channel Counter Bandwidth:


2. Rotate the DIAL knob to select Set Mode Item 17: CH CNT .



Set Mode Item.

4. Rotate the DIAL knob to select the desired bandwidth.


VX-3R O

PERATING

M

ANUAL

69

M

ESSAGE

F

EATURE

The VX-3R provides a message feature, which sends a message (up to 16 characters) instead of sending a voice. 20 different messages can be programmed, and one of them can be selected and transmitted with your ID.

Note

The Message Feature requires that all members (1) use the VX-3R or Vertex

Standard FTM-10R transceiver, (2) store the same messages into the message slot, (3) store the same member list into the member box, and (4) set the same frequency.

Does not send the Message through the repeater.

P

ROGRAMMING A

M

ESSAGE

(Requires all members set the same message into the same message slot in the same order.)

The VX-3R has 20 message slots, including a factory-programmed message (EMER-

GENCY). The factory-programmed message of course can be overwritten at any time with personalized messages.


2. Rotate the DIAL knob to select Set Mode Item 57: MSG.SEL

.



Set Mode Item.

4. Rotate the DIAL knob to select the desired Message slot into which you wish to store a message. The LCD displays the previously stored message.

5. Press the [V/M] key momentarily to enable programming of the message.

6. Press and hold in the [HM/RV] key for one second to clear the previously stored message, if desired.

7. Rotate the DIAL knob to select the first character of the message you wish to store, and then press the [V/M] key to save the first character of the message and move on to the next place.

8. Repeat the previous step to complete the message (up to 16 characters). If you make a mistake, press the [BAND] key to move back to the incorrect character, then re-enter the correct character.

9. Press the [HM/RV] key to delete all data after the cursor that may have been previously stored erroneously.

10. When the Message entry is complete, press the [TXPO] key momentarily.

11. If you wish to store another message, repeat steps 3 through 10 above.

12. Press the PTT switch to exit to normal operation.

70 VX-3R O

PERATING

M

ANUAL

M

ESSAGE

F

EATURE

P

ROGRAMMING A

M

EMBER

L

IST

(Requires all members set the same member list (includes own ID) into the same member box in the same order.)

It is possible to register a maximum of 20 persons, in order to identify the sender. When you receive a message transfer, you can know who sent the message by the ID in the register. In addition, your ID can be sent to the members when you transmit any messages to them.

If all the members share the register information (ID), the message sender ID will be shown on the display when receiving the message.

BER 1 ” though “MEMBER20 ” will be displayed when receiving a message.

We recommend that you use your call sign for the member list.


2. Rotate the DIAL knob to select Set Mode Item 55: MSG.LST

.



Set Mode Item.

4. Rotate the DIAL knob to select the desired member box (01 ~

20 ) into which you wish to store a member ID. The LCD will display the previously stored personal ID.

5. Press the [TXPO] key momentarily to enable programming of the personal ID.

6. Press the [HM/RV] key to clear the previously stored personal

ID, if desired.

7. Rotate the DIAL knob to select the first character of the personal

ID you wish to store, and then press the [V/M] key to save the first character of the personal ID and move on to the next place.

8. Repeat previous step to complete the personal ID (up to 8 characters). If you make a mistake, press the [BAND] key to move back to the incorrect character, then re-enter the correct character.


10. When the personal ID entry is complete, press the [TXPO] key momentarily.

11. If you wish to store another personal ID, repeat steps 3 through 10 above.

12. Press the PTT switch to exit to normal operation.

VX-3R O

PERATING

M

ANUAL

71

M

ESSAGE

F

EATURE

S

ET YOUR

P

ERSONAL

ID

You choose your personal ID from the member list.


2. Rotate the DIAL knob to select Set Mode Item 56: MSG.REG

.



Set Mode Item.

4. Rotate the DIAL knob to select the member box (1 ~ 20 ) where your ID is stored.


S

ENDING A

M

ESSAGES

The registered message can be sent to the members who are receiving the coordination frequency. When a message is sent, the transmitter’s ID will be sent also, and the receiver can identify who sent the message.

The “Personal ID” setting (described previous paragraph) is required for the transmitter’s

ID to be shown with the received message.

1. Set the radio to the coordination frequency.


3. Rotate the DIAL knob to select Set Mode Item 79: SQ TYP .



Set Mode Item.

5. Rotate the DIAL knob to select “MESSAGE ” (to activate the

Message feature).

6. Press the [TXPO] key momentarily, then rotate the DIAL knob to select Set Mode Item 57: MEG.SEL

.


Set Mode Item.

8. Rotate the DIAL to select the message you wish to send.

9. Press the PTT switch to exit from the Set Mode and activates the

Message feature.

10. When the Message feature is activated, the “M ” notation will appear at the 100 MHz digit of the frequency.

11. Press the PTT switch again (without speaking into the microphone) to transmit the selected message on the coordination frequency. It takes approximately 6 seconds to transmit the message.

72 VX-3R O

PERATING

M

ANUAL

M

ESSAGE

F

EATURE

R

ECEIVING A

M

ESSAGE

1. Set the radio to the coordination frequency.


3. Rotate the DIAL knob to select Set Mode Item 79: SQ TYP .



Set Mode Item.

5. Rotate the DIAL knob to select “MESSAGE ” (to activate the

Message feature).

6. Press the PTT switch to exit from the Set Mode and activates the

Message feature.

7. When you receive a message: a beep sounds, the TX/BUSY indicator blinks white, and [“Message” FROM “sending station’s

ID”] scrolls on the display.

8. Press any key (except [VOL] key) to clear the received message, and wait for a new message.

To disable the Message feature, repeat the above procedure, rotating the DIAL knob to select “OFF ” in step 5 above.

If you enable the CTCSS/DCS/EPCS Bell feature (described previously), you can confirm that a message is coming in by a ringing “bell” sound alert.

VX-3R O

PERATING

M

ANUAL

73

E

MERGENCY

F

EATURE

E

MERGENCY

C

HANNEL

O

PERATION

The VX-3R includes an “Emergency” feature, which may be useful if you have someone monitoring on the same frequency as your transceiver’s UHF “Home” channel. See page

44 for details on setting the Home channel.

The “Emergency” feature is activated by pressing and holding in the [HM/RV] key for one second.

When this is done, (A) the radio is placed on the UHF amateur band Home channel, (B) it emits a loud “Alarm” sound (the volume is controlled by rotating the DIAL knob while pressing and holding the [VOL] key), (C) it flashes the TX/BUSY indicator in white, (D) if you press the PTT switch, you will disable the Emergency feature temporarily. You can then transmit on the UHF Home channel, and (E) two seconds after the PTT release, the

Emergency feature will resume.

To disable the “Emergency” feature, press and hold the [HM/RV] key for one second or turn the radio Off by pressing and holding in the POWER switch for one second.

Use this feature if you are out for a walk and want a quick way of alerting a family member to a dangerous situation. The alarm sound may discourage an attacker and allow you to escape.

1) Be sure to arrange with a friend or family member to be monitoring on the same frequency, as there will be no identification sent via the Emergency alarm sound. And do not transmit the alarm tone except in a true emergency!

2) The TX/BUSY indicator may be changed to another function via Set Mode Item 32:

EMG.SEL; see page 110.

74 VX-3R O

PERATING

M

ANUAL

E

MERGENCY

F

EATURE

E

MERGENCY

A

UTOMATIC

ID (EAI) F

EATURE

The Emergency Automatic ID (EAI) feature can be used to aid in searching for persons who are incapacitated in disasters like earthquakes, especially search-and-rescue personnel who may have become injured in a debris field. When using the EAI feature, a searcher transmits a unique command (CTCSS tone pair), which will automatically cause the injured party’s radio to transmit, so others may perform direction-finding and effect a rescue.

The incapacitated party may not be able to speak or even press the PTT switch. The callsign of the incapacitated person will also be transmitted, to assist the rescue team.

If an emergency group is working in a dangerous area, all members should engage the EAI feature on their transceiver, so that others can assist a fallen team member, if necessary.

The Emergency Automatic ID (EAI) Feature has two operating modes: (1) Interval mode and (2) Continuous mode.

In the Interval mode (when the VX-3R receives the CTCSS tone pair), the radio will automatically transmit a brief (0.5 second) beep tone every 2.5 seconds until the EAI timer expiration.

In the continuous mode, the radio will automatically transmit continuously (with maximum microphone gain), until the EAI timer expiration.

The EIA is activated when the CTCSS tone pair stored in the Receiving Pager Code Memory

(configured via Set Mode Item 61: PAG.CDR

) is received for 5 seconds on the frequency, which is stored in Memory Channel “EAI ”. It is NOT necessary for the incapacitated person to press the PTT switch.

If your call sign is stored in the radio and the CW identifier is enabled via Set Mode Item

19: CW ID , the radio will transmit your callsign on the air when the EAI feature is first activated by the remote page, and every 10 minutes thereafter. The “callsign” ID can be changed to any desired sequence of characters, such as a name. After sending the callsign or name, the radio will repeatedly transmit three tones for a user-defined period of time

(between 1 and 30 minutes). The callsign or name will be transmitted every 10 minutes.

The Emergency Automatic ID (EAI) Feature requires that you (1) store the CTCSS Tone

Pair into the Receiving Pager Memory (see page 34 for procedure), and (2) store the desired UHF coordination frequency into Memory Channel “EAI ” (see page 42 for procedure).

VX-3R O

PERATING

M

ANUAL

75

E

MERGENCY

F

EATURE

E

MERGENCY

A

UTOMATIC

ID (EAI) F

EATURE

Selecting the EAI mode and its Transmit Time


2. Rotate the DIAL knob to select Set Mode Item 31: EAI.TMR

.



Set Mode Item.

4. Rotate the DIAL knob to select the desired EAI mode (Interval

EAI “INT ” or Continuous EAI “CON ”) and transmit time (1 -10 ,

15 , 20 , 30 , 40 , and 50 minutes).


A

CTIVATING THE

EAI

FEATURE


2. Rotate the DIAL knob to select Set Mode Item 30: EAI .



Set Mode Item.

4. Rotate the DIAL knob to select “ON ” (thus activating the EAI feature).

5. Press the PTT switch to save the new setting and exit to normal operation (with EAI feature “ON”).

When the EAI feature is activated, the “EAI ” notation and the Band

Number (or memory channel number) will appear alternately in the

Memory Channel Number Display Slot of the display.

To disable the EAI feature, just repeat above procedure, rotating the DIAL knob to select

“OFF ” in step “4” above.

The VX-3R will ignore the EAI feature when the (1) the squelch is open, (2) there is an incoming signal on the operating frequency, (3) the operating frequency is the same as the frequency which is stored in the Memory Channel “EAI,” or (4) a VHF frequency is stored in Memory Channel “EAI.”

76 VX-3R O

PERATING

M

ANUAL

E

MERGENCY

F

EATURE

E

MERGENCY

A

UTOMATIC

ID (EAI) F

EATURE

T

O

L

OCATE AN

U

NRESPONSIVE

O

PERATOR

U

SING THE

EAI

FEATURE

1. Recall the Memory Channel “EAI ” (must be the same as the searched person’s radio), which is found in the next to the last

“regular” memory channel.

2. Set the CTCSS tone pair to the same CTCSS tone pair stored in the Receiving Pager Code Memory of the missing person’s radio.

A. Press and hold in the [TXPO] key for one second to enter the Set mode.

B. Rotate the DIAL knob to select Set Mode Item 62: PAG.CDT

.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob

C. Press the [TXPO] key to enable adjustment of this Set

Mode Item.

D. Rotate the DIAL knob to select the first tone.

E. Press the [V/M] key.

F. Rotate the DIAL knob to select the second tone.

G. Press the PTT switch to save the new setting and exit from setting mode.

3. Press and hold in the PTT switch for five seconds. If the EAI signal is received by a

VX-3R transceiver programmed with matching EAI CTCSS tones the EAI feature will activate. The lost operator’s radio will beep loudly, and its transmitter will respond repetitively. You may now begin direction-finding efforts.

4. The ATT (Front End Attenuator) is often useful in locating the missing person's radio, as peaks in weaker signals are more easily observed. You may select the ATT level “ATT 1 (10 dB),”

“ATT 2 (50 dB),” and “ATT OFF ” by pressing the [BAND] key to reduce the signal.

5. Press the [V/M] key to exit to normal operation.

VX-3R O

PERATING

M

ANUAL

77

ARTS™

(A

UTOMATIC

R

ANGE

T

RANSPONDER

S

YSTEM

)

The ARTS™ feature uses DCS signaling to inform both parties when you and another

ARTS™-equipped station are within communications range. This may be particularly useful during Search-and Rescue situations, where is important to stay in contact with other members of your group.

Both stations must set up their DCS codes to the same code number, then activate their

ARTS™ feature using the command appropriate for their radio. Alert ringers may be activated, if desired.

Whenever you push the PTT switch, or every 25 (or 15) seconds after ARTS™ is activated, your radio will transmit a signal which includes a (subaudible) DCS signal for about 1 second. If the other radio is in range, the beeper will sound (if enabled) and the display will show “IN RNG ” as opposed to the out of range display “OUT

RNG ” in which ARTS™ operation begins.

Whether you talk or not, the polling every 15 or 25 seconds will continue until you de-activate ARTS™. You can program your radio to transmit your callsign every 10 minutes, via CW, to comply with identification requirements. When ARTS™ is de-activated, DCS will also be deactivated (if you were not using it previously in non-

ARTS™ operation).

If you move out of range for more than one minute (four pollings), your radio will sense that no signal has been received, three beeps will sound, and the display will revert to

“OUT RNG .” If you move back into range, your radio will again beep, and the display will change back to the “IN RNG ” indication.

During ARTS™ operation, your operating frequency will continue to be displayed, but no changes may be made to it or other settings; you must terminate ARTS™ in order to resume normal operation. This is a safety feature designed to prevent accidental loss of contact due to channel change, etc.

78 VX-3R O

PERATING

M

ANUAL

ARTS™

(A

UTOMATIC

R

ANGE

T

RANSPONDER

S

YSTEM

)

B

ASIC

ARTS™ S

ETUP AND

O

PERATION

1. Set both radios to the same DCS code number, per the discussion on page ??.

2. Press and hold in the [ ] key for one second. You will observe the “OUT RNG ” display on the LCD below the operating frequency. ARTS™ operation has now commenced.

3. Every 25 seconds, your radio will transmit a “polling” call to the other station. When that station responds with its own ARTS™ polling signal, the display will change to “IN RNG ” to confirm that the other station’s polling code was received in response to yours.

4. Press and hold in the [ ] key for one second to exit ARTS™ operation and resume normal functioning of the transceiver.

ARTS™ P

OLLING

T

IME

O

PTIONS

The ARTS™ feature may be programmed to poll every 25 seconds (default value) or 15 seconds. The default value provides maximum battery conservation, because the polling signal is sent out less frequently. To change the polling interval:


2. Rotate the DIAL knob to select Set Mode Item 7: ARTSIT .



Set Mode Item.

4. Rotate the DIAL knob to select the desired polling interval (15 or 25 seconds).


VX-3R O

PERATING

M

ANUAL

79

ARTS™

(A

UTOMATIC

R

ANGE

T

RANSPONDER

S

YSTEM

)

ARTS™ A

LERT

B

EEP

O

PTIONS

The ARTS™ feature allows two kinds of alert beeps (or off), to alert you to the status of

ARTS™ operation. Depending on your location and the potential annoyance associated with frequent beeps, you may choose the Beep mode which best suits your needs. The choices are:

IN RANG : The beeps are issued only when the radio first confirms that you are within range, but does not re-confirm with beeps thereafter.

ALWAYS : Every time a polling transmission is received from the other station, the alert beeps will be heard.

OFF : No alert beeps will be heard. You must look at the display to confirm current

ARTS™ status.

To set the ARTS ™ Beep mode, use the following procedure:


2. Rotate the DIAL knob to select Set Mode Item 6: ARTSBP .



Set Mode Item.

4. Rotate the DIAL knob to select the desired ARTS™ Beep mode

(see above).


80 VX-3R O

PERATING

M

ANUAL

ARTS™

(A

UTOMATIC

R

ANGE

T

RANSPONDER

S

YSTEM

)

CW I

DENTIFIER

S

ETUP

The ARTS™ feature includes a CW identifier, as discussed previously. Every ten minutes during ARTS™ operation, the radio can be enabled to send “DE (your callsign) K”. The callsign field may contain up to 16 characters.

Here’s how to program the CW Identifier:


2. Rotate the DIAL knob to select Set Mode Item 19: CW ID .



Set Mode Item.

4. Rotate the DIAL knob to set this Item to “ON ” (to enable the CW

ID function).

5. Press the [V/M] key momentarily to display any previously-stored callsign.

6. Press and hold the [HM/RV] key for 2 seconds to clear any previous callsign.

7. Rotate the DIAL knob to select the first letter/number of your callsign, then press the [V/M] key momentarily to save the first letter/number and move on to the next character.

8. Repeat the previous step, as many times as necessary, to complete your callsign. Note that the “slant bar” ( – • • – •) is among the available characters, should you be a “portable” station.

9. If you make a mistake, press the [BAND] key to backspace the cursor, then re-enter the correct letter/number.

10. Press and hold the [HM/RV] key for 2 seconds to delete all data after the cursor that may have been previously stored erroneously.

11. When you have entered your entire callsign, press the [TXPO] key momentarily to confirm the callsign, then press the PTT switch to save the settings and exit to normal operation.

1) You may check your work by monitoring the entered callsign. To do this, repeat steps 1- 3 above, then press the [F/W] key.

2) You may adjust the monitoring tone (CW sidetone pitch) via Set Mode Item

21: CW PIT. Available selections are 400 - 1000 Hz (50 Hz/step).

VX-3R O

PERATING

M

ANUAL

81

I

NTERNET

C

ONNECTION FEATURE

The VX-3R can be used to access a “node” (repeater or base station) which is tied into the

Vertex Standard WIRES™ (Wide-Coverage Internet Repeater Enhancement System) network, operating in the “SRG” (Sister Radio Group) mode. Details may be found at the

WIRES-II Web site: http://www.vxstd.com/en/wiresinfo-en/. This feature may also be used to access other systems, as described below.

SRG (“S

ISTER

R

ADIO

G

ROUP

”)

MODE

1. Press the [ ] key to activate the Internet Connection feature.

The “ ” icon will appear in the upper right corner of the display.

2. Rotate the DIAL knob, while pressing and holding in the [ ] key, to select the access number (“DTMF 0 ” - “DTMF 9 ”, “DTMF A ”, “DTMF B ”,

“DTMF C ”, “DTMF D ”, “DTMF E ¼) ”, “DTMF F #)”) corresponding to the WIRES™ repeater to which you wish to establish an Internet link (ask your repeater owner/operator if you don’t know the access numbers in the network). Now press the PTT switch to exit from the selection mode.


3. With the Internet Connection feature activated (as in step 1 above), the VX-3R will generate a brief (0.1 second) DTMF tone according to your selection in step 2. This

DTMF tone is sent at the beginning of every transmission to establish or maintain the link to the remote WIRES™ repeater operating in the SRG mode.

4. To disable the Internet Connection feature, press the [ ] key again (The “ ” icon disappear from the display.

If other users report that you always have a DTMF “beep” at the beginning of each transmission, and you are not operating in conjunction with Internet access, disable this function via step 4 above.

82 VX-3R O

PERATING

M

ANUAL

I

NTERNET

C


FRG (“F

RIENDLY

R

ADIO

G

ROUP

”)

MODE

You may access other Internet Link Systems (including WIRES ™ in the FRG mode) that use a DTMF string for access.

P

ROGRAMMING THE

FRG

CODE

Load the DTMF tones which you wish to use for Internet-link access into an Internet

Memory Register. For purposes of this example, we will use “#(F)1101D” as the access code (the “#” key is denoted by the letter “F”).


2. Rotate the DIAL knob to select Set Mode Item 41: INT.SEL

.


3. Press the [TXPO] key to enable adjustment of this Set Mode

Item.

4. Rotate the DIAL knob to select the DTMF Memory register

(“F 0 ” - “F63 ”) into which you wish to store the access code.

5. Press the [V/M] key momentarily. The first digit will blink.

6. Rotate the DIAL knob to select “FFFFF” (representing DTMF “#”: the first digit of the DTMF string).

7. Press the [V/M] key momentarily to accept the first digit and move to the second digit of the DTMF string.

8. If you make a mistake, press the [BAND] key to backspace the cursor, then re-enter the correct letter or number.

9. Repeat steps 6 through 8 until you have completed the access code (“F(#)1101D”).

10. If you wish to attach an alpha/numeric name “Tag” to the Internet

Memory, proceed to the next step; otherwise press the PTT switch to save the settings and exit to normal operation.

11. Press the [V/M] key twice. The DTMF Memory register number blinks.

12. Press the [MODE] key momentarily (the “-----ALPHA ” notation appear in the display for 2 seconds), then press the [V/M] key momentarily to enable programming of the name tag.



15. If you make a mistake, press the [BAND] key to back-space the cursor, then re-enter the correct letter, number, or symbol.

16. Repeat steps 13 through 15 to program the remaining letters, numbers, or symbols of the desired label. Six characters may be used in the creation of a label.

VX-3R O

PERATING

M

ANUAL

83

I

NTERNET

C


FRG (“F

RIENDLY

R

ADIO

G

ROUP

”)

MODE

17. When you have programmed a label that is less than 6 characters, press the [TXPO] key to confirm the label.

18. Repeat steps 3 through 17 to store other access codes, if so desired.

19. Press the PTT switch to save the settings and exit to normal operation.

O

PERATION

(A

CCESSING AN

FRG N

ODE

)

1. Press and hold in the [TXPO] key for one second to enter the Set mode again.

2. Rotate the DIAL knob to select Set Mode Item 39: INT MD .



Item.

4. Rotate the DIAL knob to set this Set Mode Item to “FRG ” (thus activating the “Other Internet Link System” mode).

5. Press the PTT switch to save the new settings.

6. Press the [ ] key momentarily to activate the Internet Connection feature. The “ ” icon will appear in the upper right corner of the display.

7. Rotate the DIAL knob while pressing the [ ] key to select the

Internet Memory register number (“F 0 ” - “F63 ”) corresponding to the Internet link repeater to which you wish to establish an

Internet link, then press the PTT switch momentarily to lock in the selected access number.

8. Once the Internet Connection feature is activated per step 7 above, you may now press the [ ] key, while you are transmitting, to send out the selected DTMF string (to establish the link to the desired Internet-link mode).

9. To return to the WIRES™ SRG mode, repeat steps 1 - 5 above, selecting “SRG ” in step 4.

84 VX-3R O

PERATING

M

ANUAL

DTMF O

PERATION

Despite the lack of a DTMF keypad, you can still transmit DTMF tones with the VX-3R for repeater control or autopatch use.

M

ANUAL

DTMF T

ONE

G

ENERATION


2. Rotate the DIAL knob to select Set Mode Item 26: DT A /M .



Item.

4. Rotate the DIAL knob to select “MANUAL .”

5. Press the PTT switch to return to normal display.

6. Hold the PTT switch in to continue transmitting during the following steps.

A. Press the [TXPO] key momentarily.

B. Rotate the DIAL knob to select the number to be sent, and then press the [TXPO] key momentarily to send the number.

C. Repeat step B as many times as needed until you have completed the number string.

D. Release the PTT switch.

The DTMF “¼ ” code is displayed as “E,” and the DTMF code “#” is displayed as “F” on the display.

DTMF A

UTODIALER

10 DTMF Autodial memories are provided, allowing you to store telephone numbers for autopatch use. You can also store short autopatch or Internet-link access code streams to avoid having to send them manually.

Here is the DTMF Autodial storage procedure:


2. Rotate the DIAL knob to select Set Mode Item 28: DT SEL .



Item.

4. Rotate the DIAL knob to select the DTMF Memory register

(“CH0 ” - “CH9 ”) into which you wish to store this DTMF string.

5. Press the [V/M] key to begin DTMF Memory entry into the selected register. The first digit location will blink.

6. Press and hold the [HM/RV] key for 2 seconds to clear any pre-

VX-3R O

PERATING

M

ANUAL

85

DTMF O

PERATION

DTMF A

UTODIALER vious stored telephone number.

7. Rotate the DIAL knob to select the first digit of the DTMF string. Selectable entries are 1 - 9 A - FFFFF, with E and F representing DTMF “¼” and “#” tones respectively.

8. Press the [V/M] key momentarily to accept the first digit and move on to the second digit of the DTMF string.

9. Repeat the previous steps until you have completed the telephone number string.

10. If you make a mistake, press the [BAND] key to backspace the cursor, then re-enter the correct digit.

11. Press the [TXPO] key momentarily to store the string into the DTMF memory.

12. To store another number, press the [TXPO] key again, then rotate the DIAL knob to select another DTMF Memory register, and repeat this procedure.

Press the [F/W] key to check (monitoring) the entered telephone number.

13. When finished storing DTMF Memories, press the PTT switch to return to normal display.

To send the telephone number:


2. Rotate the DIAL knob to select Set Mode Item 26: DT A /M .



Item.

4. Rotate the DIAL knob to set this Item to “AUTO .”

5. Press the PTT switch to return to normal display.

6. Hold the PTT switch to continue transmitting during following steps.

A. Press the [TXPO] key momentarily.

B. Rotate the DIAL knob to select the DTMF Memory register (CH 0 through CH 9 ) you wish to send.

C. Press the [TXPO] key momentarily to transmit the tone string.

Once the string begins, you may release the PTT switch, as the transmitter will be held “on the air” until the DTMF string is completed.

86 VX-3R O

PERATING

M

ANUAL

DTMF O

PERATION

DTMF A

UTODIALER

The speed at which the DTMF digits are sent can be changed. Two speed levels are available: Low (10 digits per second) and High (20 digits per second: default). To toggle between Low and High speed, use the following procedure:


2. Rotate the DIAL knob to select Set Mode Item 29: DT SPD .



Item.

4. Rotate the DIAL knob to select the desired speed (“50MS ”: High speed or “100 MS ”: Low speed).


You can also set a longer delay between the time your transmitter is keyed and the first

DTMF digit is sent. To set the delay time, use the following procedure:


2. Rotate the DIAL knob to select Set Mode Item 27: DT DLY .



Item.

4. Rotate the DIAL knob to select the desired delay (50 /250 450 /

750 /1000MS ).


VX-3R O

PERATING

M

ANUAL

87

CW L

EARNING

F

EATURE

The VX-3R provides a CW learning function, which sends the designated Morse Code via the sidetone (heard in the speaker) to help your CW learning.


2. Rotate the DIAL knob to select Set Mode Item 20: CWLRNG .



Set Mode Item.

4. Press the [MODE] key to select the Training mode (displayed in fine print at the upper edge of the LCD):

A : Sends the Alphabet characters

A_r : Sends the Alphabet characters (move to next character automatically) n : Sends the Numeric characters n_r : Sends the Numeric characters (move to next character automatically)

S : Sends the Symbol characters

S_r : Sends the Symbol characters (move to next character automatically)

5. Rotate the DIAL knob to select the Morse speed. You may select the units of the code speed between “CPM (characters per minute)” and “WPM (Words per minute)” by pressing the [V/M] key.

6. Press the [BAND] key to switch the flashing of the LED (white) on and off; a “dot” by the CW speed indicates that the LED is on.

7. Press the [HM/RV] key to change the display on the right. Rotate the DIAL knob to select the CW code which you want to learn and press the [V/M] key select the repetition time (1 - 9) of the sending.

8. Press the [F/W] key to begin generating the selected code characters the designated number of times (Only the speaker CW

CW Code

Repetition Time sidetone is heard, the radio does not transmit).

9. If one of the “rrrrr” modes is selected in step 4 above, you may change the direction of the character rotation by tuning the DIAL knob.

10. You may adjust the CW sidetone audio level by rotating the DIAL knob while pressing and holding the [VOL] key.

11. If one of the “rrrrr” modes is not selected in step 4 above, press the [F/W] key to send again, or select another code by rotating the DIAL knob and press the [F/W] key to begin generation.

If one of the “rrrrr” modes is selected in step 4 above, press the [F/W] key to stop the CW generation.

12. To stop the CW generation, press the [F/W] key again.

13. To disable the CW learning feature, press the PTT switch.

88 VX-3R O

PERATING

M

ANUAL

CW L

EARNING

F

EATURE

1) The “CPM” selection is based on the international “PARIS” standard, which stipulates five characters per word.

2) You may adjust the CW sidetone pitch via Set Mode Item 21: CWPTCH.

Available selections are 400 - 1000 Hz (50 Hz/step).

VX-3R O

PERATING

M

ANUAL

89

CW T

RAINING

F

EATURE

The VX-3R provides another CW learning function; call it a CW Training feature, which sends random Morse Code via the sidetone (heard in the speaker), so you can improve your CW proficiency.


2. Rotate the DIAL knob to select Set Mode Item 22: CWTRNG .



Set Mode Item.

4. Press the [MODE] key to select the Training mode (displayed in fine print at the upper edge of the LCD):

A : Sends five Alphabet characters only

A_r : Sends Alphabet characters only (Repeatedly) n : Sends five Numeric characters only n_r : Sends Numeric characters only (Repeatedly)

An : Sends five Alphabet, Numeric, “?,” and “/” characters (Mixed)

Anr : Sends Alphabet, Numeric, “?,” and “/” characters (Mixed, Continuously in groups of five)

5. Rotate the DIAL knob to select the Morse speed. You may select the units of the code speed between “CPM (characters per minute)” and “WPM (Words per minute)” by pressing the [V/M] key.

6. Press the [BAND] key to switch the flashing of the LED (white) on and off; a “dot” by the CW speed indicates that the LED is on.

7. Press the [F/W] key to begin generation of the code characters (CW sidetone only, the radio does not transmit); the transmitted characters will appear on the display.

If one of the “rrrrr” modes is not selected in step 4 above, press the

[F/W] key to send another code group.

If one of the “rrrrr” modes is selected in step 4 above, press the [F/W] key to stop the CW generation.

8. Rotate the DIAL knob while press and holding the [VOL] key to adjust the CW sidetone outputs level.

9. Press the PTT switch to disable the CW Training feature and exit to normal operation.

1) The “CPM” selection is based on the international “PARIS” standard, which stipulates five characters per word.

2) You may adjust the CW sidetone pitch via Set Mode Item 21: CWPTCH.

Available selections are 400 - 1000 Hz (50 Hz/step).

90 VX-3R O

PERATING

M

ANUAL

M

ISCELLANEOUS

S

ETTING

P

ASSWORD

The VX-3R provides a password feature which can minimize the chance that your transceiver could be used by an unauthorized party.

When the password feature is activated, the radio will ask for the four digit password to be entered when the radio is first turned on. You must enter the four digit password using the

DIAL knob and [V/M] key (pressing the [V/M] key to select the password digit and rotating the DIAL knob to select the password in each digit). If the wrong password is entered, the microprocessor will shut down the radio automatically.

To enter the password and activating this feature, use the following procedure:


2. Rotate the DIAL knob to select Set Mode Item 66: PSWD .



Set Mode Item.

4. Press the [V/M] key momentarily to display any previously-stored password.

5. Rotate the DIAL knob to select the first digit of the desired number/letter (0 - 9 , A , B C , D , EEEEE, and FFFFF).

6. Press the [V/M] key to move to the next digit.

7. Repeat steps 5 and 6 to program the remaining numbers/letters of the desired password.

8. If you make a mistake, press the [BAND] key to move back to the previous digit, then re-select the correct number/letter.

9. When you have finished entering the password, press the [V/M] key and rotate the DIAL knob to select “ON ” (to activate the password feature).


If you wish to disable the Password feature, repeat steps 1 - 3 above, then rotating the

DIAL knob to select “OFF ”, then press the PTT switch.

1) We recommend that you to write down the password number, and keep it in a safe place you can easily find if you forget your password.

2) If you forget the password number, you may turn on the transceiver by performing the “Microprocessor Resetting” procedure (see page 101). However, the

VX-3R will clear the password, as well as all memories, and will restore all other settings to factory defaults.

VX-3R O

PERATING

M

ANUAL

91

M

ISCELLANEOUS

S

ETTING

P

ROGRAMMING THE

[ ] K

EY

The Internet Key is the factory default (“primary” press key) function of the [ ] key.

However, you may change the “primary” (press key) function of the [ ] key to another function via the Set Mode.


2. Rotate the DIAL knob to select Set Mode Item 42: INTKEY .



Set Mode Item.

4. Rotate the DIAL knob to select the desired function:

INTNET : Activates/Disables the internet feature.

INT MR : Recalls the Internet Access Number (SRG) or Access

String (FRG). Select the SRG number or FRG string via Set Mode Item 39:

INT MD .

SET MD : It is short cut path to recall one of the Set Mode Items. See below box for programming.


When INT MR or SET MD is assigned to the [ ] key, the INTNET function may be activated/disabled via Set Mode Item 43: INTNET.

A

SSIGN THE

S

ET

M

ODE

I

TEM TO THE

[ ]

KEY

1. Change (“primary” press key) function of the [ ] key to “SET MD ”, via Set

Mode Item 42: INTKEY , as descried above.

2. Press and hold in the [TXPO] key for one second to enter the Set mode again.

3. Rotate the DIAL knob to select the Set Mode Item which you wish to assign to the [ ] key as a Menu short-cut.


4. Press and hold in the [ ] key for one second to assign the Set Mode Item to the [ ] key. “MY KEY ” will appear on the display, to confirm that the command was executed.


Now, momentarily pressing of the [ ] key will immediately recall the selected

Set Mode Item. You must press the [ ] key again to exit to normal operation.

92 VX-3R O

PERATING

M

ANUAL

M

ISCELLANEOUS

S

ETTING

ATT (F

RONT

E

ND

A

TTENUATOR

)

The attenuator will reduce all signals (and noise) by 20 dB, and it may be used to make reception more pleasant under extremely crowded conditions.


2. Rotate the DIAL knob to select Set Mode Item 3: ANT.ATT

.



Set Mode Item.

4. Rotate the DIAL knob to change the setting from “OFF ” to “ON ”.

5. When you have made your selection, press the PTT switch to save the new setting and exit to normal operation.

6. If you wish to disable the attenuator, just repeat the above procedure, rotating the

DIAL knob to select “OFF ” in step “4” above.

When the attenuator is activated, the Operating Mode icon (AM or FM) will blink on the display.

R

ECEIVE

B

ATTERY

S

AVER

S

ETUP

An important feature of the VX-3R is its Receive Battery Saver, which “puts the radio to sleep” for a time interval, periodically “waking it up” to check for activity. If somebody is talking on the channel, the VX-3R will remain in the “active” mode, then resume its “sleep” cycles when the signal drops. This feature significantly reduces quiescent channel battery drain. You may change the amount of “sleep” time between activity checks using the Set

Mode:


2. Rotate the DIAL knob to select Set Mode Item 72: SAVERX .



Set Mode Item.

4. Rotate the DIAL knob to select the desired “sleep” duration. The selections available are 200 - 1000 1 - 10 seconds (1 sec/step), or OFF


When you are operating on Packet, switch the Receive Battery Saver OFF, as the sleep cycle may “collide” with the beginning of an incoming Packet transmission, causing your TNC not to receive the full data burst.

VX-3R O

PERATING

M

ANUAL

93

M

ISCELLANEOUS

S

ETTING

W

AKEUP

F

EATURE

The Wakeup feature is similar to the Receive Battery Saver. However, it is a newer, more advanced feature which conserves battery life by providing a longer “sleep” time than the regular Receive battery Saver. The Wakeup feature, once engaged, operates while the transceiver is turned off (“WAKEUP ” will appear on the LCD).

To set up the Wakeup feature:


2. Rotate the DIAL knob to select Set Mode Item 93: WAKEUP .



Set Mode Item.

4. Rotate the DIAL knob to select the desired “sleep” duration.

5 - 60SEC : (5 second/steps) Based on the selected time value, the radio will periodically check the operating frequency which it was on

EAI : when the radio was turned off for activity. (That was in use when the radio was turned off.) If a signal is received on the frequency strong enough to open the Squelch, the radio will turn itself on fully. If the EAI feature was activated when the radio was turned off, the radio also checks on the

EAI frequency (Memory Channel “EAI ”) for activity.

Checks the EAI frequency (Memory Channel “EAI ”) every 5 seconds. If a properly-coded signal is received on the EAI frequency, the radio will turn itself on and then automatically transmit in accordance with the setting of Set Mode Item 30: EAI .

OFF : Disables the Wakeup feature.


If you wish to disable the Wakeup feature, just repeat the above procedure, rotating the

DIAL knob to select “OFF ” in step 4 above.

When the radio is turned off, the Wakeup feature will be engaged, and the “WAKEUP ” notation will be seen on the display.

You may cancel the Wakeup feature (complete power off) temporarily by pressing the POWER switch while the Wakeup feature is engaged.

94 VX-3R O

PERATING

M

ANUAL

M

ISCELLANEOUS

S

ETTING

TX B

ATTERY

S

AVER

The VX-3R also includes a useful Transmit Battery Saver, which will automatically lower the power output level when the last signal received was very strong. For example, when you are in the immediate vicinity of a repeater station, there generally is no reason to use the High Power output in order to achieve full-quieting access to the repeater. With the

Transmit Battery Saver, the automatic selection of Low Power operation conserves battery drain significantly.

To activate the Transmit Battery Saver:


2. Rotate the DIAL knob to select Set Mode Item 73: SAVETX .



Set Mode Item.

4. Rotate the DIAL knob to set this Set Mode Item to “ON ” (thus activating the Transmit Battery Saver).


D

ISABLING THE

BUSY I

NDICATOR

Further battery conservation may be accomplished by disabling the BUSY indicator while receiving a signal. Use the following procedure:


2. Rotate the DIAL knob to select Set Mode Item 16: BSY.LED

.



Set Mode Item.

4. Rotate the DIAL knob to set this Set Mode Item to “OFF ” (thus disabling the BUSY lamp).


VX-3R O

PERATING

M

ANUAL

95

M

ISCELLANEOUS

S

ETTING

A

UTOMATIC

P

OWER

-O

FF

(APO) F

EATURE

The APO feature helps conserve battery life by automatically turning the radio off when there has been no dial or key activity for a user-defined period. The available selections for the time before power-off are 0.5 - 12 hours (0.5 hour/step), as well as APO Off. The default condition of the APO is OFF. This is the procedure to activate it:


2. Rotate the DIAL knob to select Set Mode Item 4: APO .



Set Mode Item.

4. Rotate the DIAL knob to select the desired time period after which the radio will automatically shut down.


When the APO is activated, the “ ” icon will appear at the center bottom on the LCD. If there is no action by you within the time interval programmed, a ringer sounds 3 minutes before the APO shutdown time. Three minutes thereafter, the microprocessor will shut down the radio automatically.

Just press and hold in the POWER switch for one second to turn the transceiver back on after an APO shutdown, as usual.

96 VX-3R O

PERATING

M

ANUAL

M

ISCELLANEOUS

S

ETTING

T

RANSMITTER

T

IME

-O

UT

T

IMER

(TOT)

The TOT feature provides a safety switch, which limits transmission time to a pre-programmed value. This will conserve battery power by limiting the length of transmissions.

In the event of a stuck PTT switch (perhaps if the radio or a Speaker/Mic is wedged between car seats) it can prevent interference to other users as well as battery depletion.

The TOT default is 3 minutes. To adjust the timer, follow the procedure below:


2. Rotate the DIAL knob to select Set Mode Item 87: TOT .



Set Mode Item.

4. Rotate the DIAL knob to set the Time-Out Timer to the desired

“Maximum TX” time. The available selections are 0.5 - 10 minutes (0.5 minute/step).


1) When your transmission time is within 10 seconds of the Time-Out Timer expiration, an Alert bell will provide an audible warning from the speaker.

2) Since brief transmissions are the mark of a good operator, try setting up your radio’s TOT feature for a maximum transmission time of one minute. This will significantly improve battery life, too!

VX-3R O

PERATING

M

ANUAL

97

M

ISCELLANEOUS

S

ETTING

A

UTOMATIC

P

OWER

-O

N

F

EATURE

The VX-3R also includes the capability to turn itself on after a programmed time interval.


2. Rotate the DIAL knob to select Set Mode Item 58: ON TMR .



Set Mode Item.

4. Rotate the DIAL knob to set the desired time after which the radio will automatically turn on. Note: that is not the time of day when the radio will turn on; it is the number of hours and minutes until the radio turns on.

The available selections are 10 minutes - 24 hours (10 minute/ step).


When the radio is turned off, this activates the Automatic Power-On feature; a countdown timer in the display will show the time remaining until automatic switch-on.

You may cancel the Automatic Power-On feature (turn off the radio), by pressing and holding the POWER switch for one second while the Automatic Power-On feature is engaged.

The Automatic Power-On feature will be ignored if the Wakeup feature is activated.

B

USY

C

HANNEL

L

OCK

-O

UT

(BCLO)

The BCLO feature prevents the radio’s transmitter from being activated if a signal strong enough to break through the “noise” squelch is present. On a frequency where stations using different CTCSS or DCS codes may be active, BCLO prevents you from disrupting their communications accidentally (because your radio may be muted by its own Tone Decoder).

The default setting for the BCLO is OFF. This is the procedure to activate the BCLO:


2. Rotate the DIAL knob to select Set Mode Item 8: BCLO .



Set Mode Item.

4. Rotate the DIAL knob to set this Set Mode Item to “ON ” (thus activating the BCLO feature).


98 VX-3R O

PERATING

M

ANUAL

M

ISCELLANEOUS

S

ETTING

C

HANGING THE

TX D

EVIATION

L

EVEL

In many areas of the world, channel congestion has required that operating channels be closely spaced. In such operating environments, it often is required that operators use reduced deviation levels, so as to reduce the potential for interference to users on adjacent channels. The VX-3R includes a simple method of accomplishing this:


2. Rotate the DIAL knob to select the Set Mode Item 35: HLF.DEV

.



Set Mode Item.

4. Rotate the DIAL knob to set this Set Mode Item to “ON .” In this configuration (HALF DEVIATION active), the transmitter’s deviation will be approximately ±2.5 kHz.


The “normal” setting for the deviation (when this Menu Item is set to “OFF”) is ±5 kHz.

C

HANGING THE

M

ICROPHONE

G

AIN

At the factory, a microphone gain has been programmed that should be satisfactory for the internal microphone. If you use an after-market microphone, you may wish to set a different microphone gain level.


2. Rotate the DIAL knob to select Set Mode Item 48: MCGAIN .



Set Mode Item.

4. Rotate the DIAL knob to select the desired microphone gain.


VX-3R O

PERATING

M

ANUAL

99

M

ISCELLANEOUS

S

ETTING

M

Y

B

ANDS

O

PERATION

The “My Bands” feature allows you to select several operating bands, and make only those bands available for selection via the [BAND] button.

For example, if you do not need the reception of the SW and Air bands, you may skip

(omit) these bands from the band selection loop.

My Bands Setup

1. Set the VX-3R to the VFO mode.


3. Rotate the DIAL knob to select Set Mode Item 91: VFO.SKP

.



Item.

5. Rotate the DIAL knob to choose a band number (see chart below) you wish to omit

(skip) form the band selection loop.

6. Press the [V/M] key, then rotate the DIAL knob to select “ON ” and omit (skip) the band from the band selection loop.

Note: The band presently in use cannot be turned “ON ”.

7. Press the [V/M] key again.

8. Repeat steps 4 through 6 above to select as many bands as you like.


Band Number

To re-institute a band into the band selection loop, repeat the above procedure, rotating the

DIAL knob to select “OFF ” in step 5.

B

AND

N

UMBER

7

8

5

6

9

A

F

3

4

1

2

If you wish to skip (omit) the AM or FM Broadcast band, enter the Broadcast

Reception mode by pressing the [RADIO] key momentarily at first, then perform the above procedure.

O

PERATING

B

AND

SW Band

50 MHz Ham Band

Air Band

144 MHz Ham Band

VHF-TV Band

Information Band 1

430 MHz Ham Band

UHF-TV Band

Information Band 2

AM Broadcast Band

FM Broadcast Band

B

AND

N

UMBER

C

HART

USA V

F

REQUENCY

R

ANGE

ERSION

1.8 - 30 MHz

EXP V

ERSION

1.8 - 30 MHz

30 - 76 MHz

108 - 137 MHz

137 - 174 MHz

174 - 222 MHz

30 - 76 MHz

108 - 137 MHz

137 - 174 MHz

174 - 222 MHz

222 - 420 MHz

420 - 470 MHz

470 - 774 MHz

803 - 999 MHz

510 - 1790 kHz

76 - 107.9 MHz

222 - 420 MHz

420 - 470 MHz

470 - 800 MHz

803 - 999 MHz

510 - 1790 kHz

76 - 107.9 MHz

100 VX-3R O

PERATING

M

ANUAL

M

ISCELLANEOUS

S

ETTING

C

HANGING THE

S

TATUS OF THE

[VOL] K

EY

By factory default, the [VOL] key keeps the status while pressing and holding the [VOL] key down. You may change the status of the [VOL] key to keep the status for approximately three seconds after pressing the [VOL] key, after which time it reverts back to its previous status.


2. Rotate the DIAL knob to select the Set Mode Item 92: VOL MD .



Set Mode Item.

4. Rotate the DIAL knob to select the desired mode.

NORMAL : The [VOL] key keeps the status while pressing and holding the [VOL] key down.

AUT.BCK

: The [VOL] key keeps its status for approximately three seconds after pressing the [VOL] key.


VX-3R O

PERATING

M

ANUAL

101

C

LONING

The VX-3R includes a convenient “Clone” feature, which allows the memory and configuration data from one transceiver to be transferred to another VX-3R. This can be particularly useful when configuring a number of transceivers for a public service operation. Here is the procedure for Cloning one radio’s data to another:

1. Turn both radios off.

2. Connect the optional CT-27 Clone Cable between the MIC/SP jacks of the two radios.

3. Press and hold in the [F/W] key while turning the radios on. Do this for both radios (the order of switch-on does not matter).

“CLONE ” will appear on the displays of both radios when the

Clone mode is successfully activated in this step.

4. On the Destination radio, press the [V/M] key (“----- WAIT ” will appear on the LCD).

5. Press the [BAND] key on the Source radio; “----- ----- TX ” will appear on the Source radio, and the data from this radio will be transferred to the other radio.

6. If there is a problem during the cloning process, “ERROR ” will be displayed. Check your cable connections and battery voltage, and try again.

7. If the data transfer is successful, the Destination radio returns to normal operation and

“CLONE ” will reappear on the Source radio.

8. Turn both radios off and disconnect the cloning cable. You can then turn the radios back on, and begin normal operation.

CT-27 Clone Cable

102 VX-3R O

PERATING

M

ANUAL

S

ET

(M

ENU

) M

ODE

The VX-3R Set Mode, already partially discussed in many previous chapters, is easy to activate and set. The Set Mode is used to configure a wide variety of transceiver parameters, some of which have not been detailed previously. Use the following procedure to activate the Set Mode and adjust the various parameters:


2. Rotate the DIAL knob to select the Set Mode Item to be adjusted.



Set Mode Item.

4. Rotate the DIAL knob to adjust or select the parameter to be changed on the Set Mode Item selected in above step.

5. After completing your selection and adjustment, press the PTT switch momentarily to save the new setting and exit to normal operation.

Some Set Mode Items (like Set Mode Item 86: TN FRQ) require that the

[TXPO] key be pressed after setting of the parameter, and before exiting to normal operation.

M

ASKING THE

S

ET

M

ODE

I

TEMS

There may be situations where you want to “Mask” Set Mode Items so they are not recalled during Set Mode Item selection.


2. Rotate the DIAL knob to select the Set Mode Item 33: EXT.MNU

.



Set Mode Item.

4. Rotate the DIAL knob to select “ON ”, then press the [TXPO] key momentarily.

5. Rotate the DIAL knob to select the Set Mode Item to be “Masked”.

6. Press the [F/W] key momentarily. A small “

X

” icon will appear above the volume level indicator on the display, indicating the

Set Mode Item is to be Masked.

7. Rotate the DIAL knob; the previously-selected Set Mode Item will be “Masked”.

8. Repeat steps 5 - 7 above, to append the “

X

” icon to any other Set

Mode Item you wish to “Masked”.


To unmask the hidden Set Mode Item, repeat the above procedure. In step 4 above select

“OFF ” and in step 6 above the “

X

” icon will disappear from the Set Mode Item you wish to unmask.

VX-3R O

PERATING

M

ANUAL

103

S

ET

(M

ENU

) M

ODE

S

ET

M

ODE

I

TEM

1 [ANT AM]

2 [ANT FM]

3 [ANT.ATT]

4 [APO]

5 [ARS]

6 [ARTSBP]

7 [ARTSIT]

8 [BCLO]

9 [BEL.RNG]

10 [BEL.SEL]

11 [BNK.NAM]

12 [BP EDG]

13 [BP LVL]

14 [BP SEL]

15 [BP USR]

16 [BSY.LED]

17 [CH CNT]

18 [CLK.SFT]

19 [CW ID]

20 [CWLRNG]

21 [CWPICT]

22 [CWTRNG]

23 [DC VLT]

24 [DCS CD]

25 [DCS RV]

26 [DT A/M]

27 [DT DLY]

28 [DT SEL]

29 [DT SPD]

30 [EAI]

31 [EAI.TMR]

32 [EMG.SEL]

33 [EXT.MNU]

34 [FW KEY]

35 [HLF.DEV]

36 [HM/RV]

37 [HM>VFO]

38 [INT CD]

39 [INT MD]

40 [INT.A/M]

41 [INT.SEL]

42 [INTKEY]

43 [INTNET]

44 [LAMP]

45 [LED LT]

46 [LOCK]

47 [M/T-CL]

48 [MCGAIN]

49 [MR DSP]

50 [MR WMD]

F

UNCTION

Select the antenna to be used in the AM Broadcast listening.

Select the antenna to be used in the FM Broadcast listening.

Enables/Disables the receiver Front-end Attenuator.

Setting of the Automatic Power-Off feature.

Enables/Disables the Automatic Repeater Shift function.

Selects the Beep option during ARTS operation.

Selects the Polling Interval during ARTS operation.

Enables/Disables the Busy Channel Lock-Out feature.

Selects the number of Bell ringer repetitions.

Enables/Disables the Bell ringer function and its sound selection.

Stores Alpha-Numeric “Tags” for the Memory Banks.

Enables/Disables the Band-edge beeper while selecting the frequency by the DIAL knob.

Adjust the Beep volume level.

Enables/Disables the Keypad beeper.

Create the beep melody for Bell ringer function.

Enables/Disables the BUSY LED while the Squelch is open.

Selects the Channel Counter Search Width.

Shifting of the CPU clock frequency.

Programs and activates the CW Identifier (used during ARTS operation).

Enables/Disables the CW Learning feature.

Select the CW tone pitch for the CW Learn, CW training, and

CW Identifier functions.

Enables/Disables the CW Training feature.

Indicates the DC Supply Voltage.

Setting of the DCS code.

Enables/Disables the “Inverted” DCS Tone.

Enables/Disables the DTMF Autodial feature.

Selects the DTMF Autodialer Delay Time.

Programming of the DTMF Autodialer.

Selects the DTMF Autodialer Sending Speed.

Enables/Disables the Emergency Automatic ID (EAI) feature.

Sets the Emergency Automatic ID (EAI) operating mode and its Transmit Time.

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

BAREXT / BARANT

EXTANT / EARPHO

ON / OFF

OFF / 0.5H - 12.0H (0.5H/steps)

ON / OFF

OFF / IN RNG / ALWAYS

15SEC / 25SEC

ON / OFF

1T - 20T / CONT (Continuous ringing)

OFF / BELL /

USRBP1 / USRBP2 /USRBP3

---

ON / OFF

LVL 1 - LVL 9 (LVL 5)

OFF / KY+SCN / KEY

---

ON / OFF

±5 MHz / ±10 MHz / ±50 MHz / ±100 MHz

ON / OFF

---

---

400 - 1000 Hz (50 Hz/step)

(700 Hz)

---

---

104 standard DCS codes (023)

R-N.T-N / R-I.T-N / R-B.T-N / R-N.T.I /

R-I.T-I / R-B.T-I

MANUAL / AUTO

50MS / 250MS / 450MS / 750MS / 1000MS

---

50MS / 100MS

ON / OFF

INT. 1M through INT.10M, INT.15M,

INT.20M, INT.30M, INT.40M, INT. 50M,

CON. 1M through CON.10M, CON.15M,

CON.20M, CON.30M, CON.40M, and

CON. 50M (CON. 5M)

BEEP / STROBE / BP+STR / BEAM /

BP+BEM / CW / BP+CW / CWT

ON / OFF

FW0.3S / FW0.5S / FW0.7S / FW1.0S /

FW1.5S

Select the alarms utilized when the Emergency function is engaged.

Enables/Disables the extended Set Mode Menu.

Set the duration that a secondary function of the [F/W] key

(press and holding the [F/W] key) is held determines the function they activate.

Reduce the Deviation level by 50 %.

Selects the function of the [HM/RV] key.

Enables/Disables the function of the VFO DIAL knob, while in the Home Channel mode.

Selects the Access Number (DTMF digit) for the SRG operation of the Internet Connection feature (WIRES TM ).

Selects the operating mode of the Internet Connection feature

(WIRES TM ).

Enables/Disables the DTMF Autodialer, while operating the

Internet Connection feature (WIRES TM ).

Programming of the Access Number (DTMF code) for the FRG station of the WIRES TM (or non WIRES TM tem) access.

Selects the function of the [ ] key.

Internet Link Sys-

Enables/Disables the Internet Connection feature (WIRES TM ).

Selects the LCD/Keypad Lamp mode.

Illuminates the TX/BUSY indicator. It will glow continuously white (useful as emergency flashlight at night).

Selects the Control Locking lockout combination.

Selects the function of the MONI key.

Adjust the microphone gain level.

Toggles the display indication between “frequency” and “Alpha/Numeric” channel tags.

Determines the method of selecting channels for Memory Storage.

ON / OFF

HOME / REV

DISABL / ENABLE

DTMF 0 - DTMF F (DTMF 1)

SRG / FRG

MANUAL / AUTO

---

INTNET / INT MR / SET MD

ON / OFF

KEY 2S - KEY10S / CONT / OFF (KEY 5S)

---

KEY / PTT / KY (KEY)+PTT

MONI / T-CALL

LVL 1 - LVL 9 (LVL 5)

ALPHA / FREQ

NEXT / LOWER

104 VX-3R O

PERATING

M

ANUAL

S

ET

(M

ENU

) M

ODE

S

ET

M

ODE

I

TEM

51 [MRFSTP]

52 [MRNAME]

53 [MRPTCT]

54 [MRSKIP]

55 [MSG.LST]

56 [MSG.REG]

57 [MSG.SEL]

58 [ON TMR]

59 [OPN.MSG]

60 [PAG.ABK]

61 [PAG.CDR]

62 [PAG.CDT]

63 [PR FRQ]

64 [PRI.RVT]

65 [PRI.TMR]

66 [PSWD]

67 [PTT.DLY]

68 [RPT]

69 [RPT.SFT]

70 [RX MD]

71 [S SRCH]

72 [SAVERX]

73 [SAVETX]

74 [SCN.LMP]

75 [SCN.RSM]

76 [SCN.STR]

77 [SP OUT]

78 [SQ LVL]

79 [SQ TYP]

80 [SQSMTR]

81 [SQSPLT]

82 [STEP]

83 [STEREO]

84 [SUB-RX]

85 [TEMP]

86 [TN FRQ]

87 [TOT]

88 [TS MUT]

89 [TS SPD]

90 [VFO MD]

91 [VFO.SKP]

92 [VOL MD]

93 [WAKEUP]

94 [WX ALT]

F

UNCTION

Selects the channel step for the fast channel selection mode while in the Memory Recall mode.

Stores “Alpha-Numeric” tags for the Memory channels.

Enables/Disables the Memory Write Protector.

Selects the Memory Scan, channel-selection mode.

Programming a Member List for the Message feature.

Selects your Personal ID for the Message feature.

Programming a Message for the Message feature.

Set the On Timer Time.

Selects the Opening Message that appears when the radio is powered on.

Enables/Disables the Answer Back function of the Enhanced

CTCSS Paging & Code Squelch.

Sets the Receiver Pager Code for the Enhanced CTCSS Paging & Code Squelch.

Sets the Transmitting Pager Code for the Enhanced CTCSS

Paging & Code Squelch.

Program the CTCSS Tone frequency for the User programmed

Reverse CTCSS Decoder.

Enables/Disables the Priority Revert feature.

Selects the time between the Priority (Dual Watch) channel checks, when the feature is active.

Programs and activates the Password feature.

Selects the time delay before the carrier is transmitted, when the PTT switch is pressed.

Sets the Repeater Shift Direction.

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

10CH / 20CH / 50CH / 100CH

I

TARIC

)

---

ON / OFF

OFF / SKIP / ONLY

---

---

---

OFF / 00H.10M(00:10) - 24H.00M(24:00)

(10 minutes/step)

OFF / DC / MSG

ON / OFF

---

---

300Hz - 3000Hz (1000 Hz/step)

(1600Hz)

ON / OFF

0.1 - 0.9S (0.1S/step) or 1.0S - 10.0S

(0.5S/step) (5.0S)

---

OFF / 20MS / 50MS / 100MS / 200MS

Sets the magnitude of the repeater Shift.

Selects the Receiving mode.

Selects the Smart Search Sweep mode.

Selects the Receive-mode Battery Saver interval (“sleep” ratio)

Enables/Disables the Transmitter Battery Saver.

Enables/Disables the Scan lamp (while scanning is paused)

Selects the Scan Resume mode.

Select the Scan Re-start Delay time.

SIMP / -RPT / +RPT

(Depends on the operating band and transceiver viersion)

0.00 - 150.00 MHz (50 kHz/step)

(Depends on the operating band and transceiver viersion)

AUTO / N-FM / AM / W-FM

SINGLE / CONT

0.2S - 0.9S (0.1S/step) or 1.0S - 10.0S

(0.5S/step)

ON / OFF

ON / OFF

2SEC - 10SEC / BUSY / HOLD (5SEC)

0.1-0.4S (0.1S/step) or 1.0S - 10.0S

(0.5S/step) (2.0SEC)

AUTO / SPKR Enables/Disables the FM Broadcast audio output to the internal speaker when using the earphone antenna.

Sets the Squelch threshold level.

Selects the Sub Audible Squelch Type.

Adjusts the Squelch threshold to the S-meter level.

Enables/Disables split CTCSS/DCS coding.

Setting the Dial frequency steps.

Enables/Disables stereo out put, while receiving the FM Broadcast band.

Sets the time before Broadcast audio is resumed after the amateur band signal drops, when the SUB-RX operation is activated.

Indicates the current temperature inside the transceiver’s case and selects the measurement units (“°F” or “°C”) for the temperature sensor.

Setting of the CTCSS Tone Frequency.

Setting of the TOT time

Enables/Disables the receiver audio output while the Tone

Search Scanner is activated.

Selects the Tone Search Scanner speed.

LVL 0 - LVL 15 (AM and N-FM) (LVL 1),

LVL 0 - LVL 8 (LVL 2)

(Wide FM and AM Broadcast)

OFF / TONE / TSQL / DCS / RV TN /

PR FRQ / PAGER / MESSAGE

OFF / LVL 1 - LVL 8

ON / OFF

AUTO / 5 / 8.33 / 9 / 10 / 12.5 / 15 / 20 /

25 / 50 / 100 kHz

STEREO / MONO

OFF / TRX 1S - TRX 10S (1S/step) /

HOLD / TX 1S - TX 10S (1S/step)

---

50 standard CTCSS tones (100Hz)

OFF / 0.5M - 10.0M (0.5M/step) (3.0M)

ON / OFF

SLOW (1.25 tone/sec) /

FAST (2.5 tone/sec)

ALL / BAND Selects or disables the VFO band edge limiting for the current band.

Set My Band.

Select the DIAL knob function.

Setting of the Wakeup feature.

Enables/Disables the NOAA Weather Alert Feature.

ON / OFF

NORMAL / AUT.BCK

OFF / 5SEC - 60SEC(5SEC/step) / EAI

OFF / ON

VX-3R O

PERATING

M

ANUAL

105

S

ET

(M

ENU

) M

ODE

R

EPEATER

S

ETTING

Enables / Disables the Automatic Repeater Shift function.

Sets the Repeater Shift Direction.

Sets the magnitude of the repeater Shift.

CTCSS/DCS/EPCS S

ETTING

Selects the number of Bell ringer repetitions.

Enables / Disables the Bell ringer function and its sound selection.

Create the beep melody for Bell ringer function.

Setting of the DCS code.

Enables / Disables the “Inverted” DCS Tone.

Enables / Disables the Answer Back function of the Enhanced CTCSS

Paging & Code Squelch.

Sets the Receiver Pager Code for the Enhanced CTCSS Paging & Code

Squelch.

Sets the Transmitting Pager Code for the Enhanced CTCSS Paging &

Code Squelch.

Program the CTCSS Tone frequency for the User programmed Reverse

CTCSS Decoder.

Sets the Squelch threshold level.

Selects the Sub Audible Squelch Type.

S

ET

M

ODE

I

TEM

5 [ARS]

68 [RPT]

69 [RPT.SFT]

S

ET

M

ODE

I

TEM

9 [BEL.RNG]

10 [BEL.SEL]

15 [BP USR]

24 [DCS CD]

25 [DCS RV]

60 [PAG.ABK]

61 [PAG.CDR]

62 [PAG.CDT]

63 [PR FRQ]

78 [SQ LVL]

79 [SQ TYP]

Enables / Disables split CTCSS / DCS coding.

Setting of the CTCSS Tone Frequency.

ARTS S

ETTING

Selects the Beep option during ARTS TM operation.

Selects the Polling Interval during ARTS TM operation.

Programs and activates the CW Identifier (used during ARTS TM tion).

opera-

M

EMORY

S

ETTING

Stores Alpha-Numeric “Tags” for the Memory Banks.

Toggles the display indication between “frequency” and “Alpha/Numeric” channel tags.

Determines the method of selecting channels for Memory Storage.

Selects the channel step for the fast channel selection mode while in the

Memory Recall mode.

Stores “Alpha-Numeric” tags for the Memory channels.

Enables / Disables the Memory Write Protector.

S

CAN

S

ETTING

Selects the Memory Scan, channel-selection mode.

Enables / Disables the Priority Revert feature.

Selects the time between the Priority (Dual Watch) channel checks, when the feature is active.

Enables / Disables the Scan lamp (while scanning is paused)

Selects the Scan Resume mode.

Select the Scan Re-start Delay time.

81 [SQSPLT]

86 [TN FRQ]

S

ET

M

ODE

I

TEM

6 [ARTSBP]

7 [ARTSIT]

19 [CW ID]

S

ET

M

ODE

I

TEM

11 [BNK.NAM]

49 [MR DSP]

50 [MR WMD]

51 [MRFSTP]

52 [MRNAME]

53 [MRPTCT]

S

ET

M

ODE

I

TEM

54 [MRSKIP]

64 [PRI.RVT]

65 [PRI.TMR]

74 [SCN.LMP]

75 [SCN.RSM]

76 [SCN.STR]

Enables / Disables the receiver audio output while the Tone Search Scanner is activated.

Selects the Tone Search Scanner speed.

B

ATTERY

S

AVING

S

ETTING

Setting of the Automatic Power-Off feature.

Enables / Disables the BUSY LED while the Squelch is open.

Selects the Receive-mode Battery Saver interval (“sleep” ratio)

Enables / Disables the Transmitter Battery Saver.

Setting of the Wakeup feature.

M

ESSAGE

S

ETTING

Programming a Member List for the Message feature.

Selects your Personal ID for the Message feature.

Programming a Message for the Message feature.

WIRES S

ETTING

Selects the Access Number (DTMF digit) for the SRG operation of the

Internet Connection feature (WIRES TM ).

Selects the operating mode of the Internet Connection feature (WIRES TM ).

Enables / Disables the DTMF Autodialer, while operating the Internet

Connection feature (WIRES TM ).

Programming of the Access Number (DTMF code) for the FRG station of the WIRES TM (or non WIRES TM Internet Link System) access.

Selects the function of the [ ] key.

Enables / Disables the Internet Connection feature (WIRES TM ).

88 [TS MUT]

89 [TS SPD]

S

ET

M

ODE

I

TEM

4 [APO]

16 [BSY.LED]

72 [SAVERX]

73 [SAVETX]

93 [WAKEUP]

S

ET

M

ODE

I

TEM

55 [MSG.LST]

56 [MSG.REG]

57 [MSG.SEL]

S

ET

M

ODE

I

TEM

38 [INT CD]

39 [INT MD]

40 [INT.A/M]

41 [INT.SEL]

42 [INTKEY]

43 [INTNET]

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

ON / OFF

SIMP / -RPT / +RPT

0.00 - 150.00 MHz (50 kHz/step)

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

1T - 20T / CONT (Continuous ringing)

OFF / BELL / USRBP1 / USRBP2 / USRBP3

---

104 standard DCS codes (023)

R-N.T-N / R-I.T-N / R-B.T-N /

R-N.T.I / R-I.T-I / R-B.T-I

ON / OFF

---

---

300Hz - 3000Hz (1000 Hz/step)

(1600Hz)

LVL 0 - LVL 15 (LVL 1) (AM and Narrow FM),

LVL 0 - LVL 8 (LVL 2) (Wide FM and AM Broadcast)

OFF / TONE / TSQL / DCS / RV TN /

PR FRQ / PAGER / MESSAGE

ON / OFF

50 standard CTCSS tones (100Hz)

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

OFF / IN RNG / ALWAYS

15SEC / 25SEC

---

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

---

ALPHA / FREQ

NEXT / LOWER

10CH / 20CH / 50CH / 100CH

---

ON / OFF

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

OFF / SKIP / ONLY

ON / OFF

0.1 - 0.9S (0.1S/step) or 1.0S - 10.0S (0.5S/step)

(5.0S)

ON / OFF

2SEC - 10SEC / BUSY / HOLD (5SEC)

0.1-0.4S (0.1S/step) or 1.0S - 10.0S (0.5S/step)

(2.0S)

ON / OFF

SLOW (1.25 tone/sec) / FAST (2.5 tone/sec)

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

OFF / 0.5H - 12.0H (0.5H/steps)

ON / OFF

0.2S - 0.9S (0.1S/step) or 1.0S - 10.0S (0.5S/step)

ON / OFF

OFF / 5SEC - 60SEC(5SEC/step) / EAI

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

---

---

---

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

DTMF 0 - DTMF F (DTMF 1)

SRG / FRG

MANUAL / AUTO

---

INTNET / INT MR / SET MD

ON / OFF

106 VX-3R O

PERATING

M

ANUAL

EAI S

ETTING

Enables / Disables the Emergency Automatic ID (EAI) feature.

Sets the Emergency Automatic ID (EAI) operating mode and its Transmit Time.

S

ET

M

ODE

I

TEM

30 [EAI]

31 [EAI.TMR]

Select the alarms utilized when the Emergency function is engaged.

32 [EMG.SEL]

DTMF S

ETTING

Enables / Disables the DTMF Autodial feature.

Selects the DTMF Autodialer Delay Time.

Programming of the DTMF Autodialer.

Selects the DTMF Autodialer Sending Speed.

S

WITCH

/K

NOB

S

ETTING

Set the duration that a secondary function of the [F/W] key (press and holding the [F/W] key) is held determines the function they activate.

Selects the function of the [HM/RV] key.

Enables / Disables the function of the VFO DIAL knob, while in the Home

Channel mode.

Select the DIAL knob function.

D ISPLAY S ETTING

Selects the LCD/Keypad Lamp mode.

Selects the Control Locking lockout combination.

Selects the function of the MONI switch (just below the PTT switch).

Selects the time delay before the carrier is transmitted, when the PTT switch is pressed.

B

EEP

S

ETTING

Enables / Disables the Band-edge beeper while selecting the frequency by the DIAL knob.

Adjust the Beep volume level.

Enables / Disables the Keypad beeper.

Select the CW tone pitch for the CW Learn, CW training, and CW Identifier functions.

D

ISPLAY

S

ETTING

Indicates the DC Supply Voltage.

Selects the Opening Message that appears when the radio is powered on.

Indicates the current temperature inside the transceiver’s case and selects the measurement units (“°F” or “°C”) for the temperature sensor.

M ISCELLANEOUS S ETTING

Select the antenna to be used in the AM Broadcast listening.

Selects the Channel Counter Search Width.

Shifting of the CPU clock frequency.

Select the antenna to be used in the FM Broadcast listening.

Enables / Disables the CW Learning feature.

Enables / Disables the CW Training feature.

Enables / Disables the receiver Front-end Attenuator.

Enables / Disables the extended Set Mode Menu.

Reduce the Deviation level by 50 %.

Illuminates the TX/BUSY indicator. It will glow continuously white (useful as emergency flashlight at night).

Adjust the microphone gain level.

Set the On Timer Time.

S

ET

M

ODE

I

TEM

26 [DT A/M]

27 [DT DLY]

28 [DT SEL]

29 [DT SPD]

S

ET

M

ODE

I

TEM

34 [FW KEY]

36 [HM/RV]

37 [HM>VFO]

92 [VOL MD]

S ET M ODE I TEM

44 [LAMP]

46 [LOCK]

47 [M/T-CL]

67 [PTT.DLY]

S

ET

M

ODE

I

TEM

12 [BP EDG]

13 [BP LVL]

14 [BP SEL]

21 [CWPICT]

S

ET

M

ODE

I

TEM

23 [DC VLT]

59 [OPN.MSG]

85 [TEMP]

S ET M ODE I TEM

1 [ANT AM]

17 [CH CNT]

18 [CLK.SFT]

2 [ANT FM]

20 [CWLRNG]

22 [CWTRNG]

3 [ANT.ATT]

33 [EXT.MNU]

35 [HLF.DEV]

45 [LED LT]

48 [MCGAIN]

58 [ON TMR]

Programs and activates the Password feature.

Selects the Receiving mode.

Selects the Smart Search Sweep mode.

Enables / Disables the FM Broadcast audio output to the internal speaker when using the earphone antenna.

Enables / Disables the Busy Channel Lock-Out feature.

Adjusts the Squelch threshold to the S-meter level.

Setting the Dial frequency steps.

Enables / Disables stereo out put, while receiving the FM Broadcast band.

Sets the time before Broadcast audio is resumed after the amateur band signal drops, when the AF Priority function is activated.

Setting of the TOT time

Selects or disables the VFO band edge limiting for the current band.

Set My Band.

Enables/Disables the NOAA Weather Alert Feature.

66 [PSWD]

70 [RX MD]

71 [S SRCH]

77 [SP OUT]

8 [BCLO]

80 [SQSMTR]

82 [STEP]

83 [STEREO]

84 [SUB-RX]

87 [TOT]

90 [VFO MD]

91 [VFO SKP]

94 [WX ALT]

S

ET

(M

ENU

) M

ODE

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

ON / OFF

INT. 1M through INT.10M, INT.15M, INT.20M,

INT.30M, INT.40M, INT. 50M,CON. 1M through

CON.10M, CON.15M, CON.20M, CON.30M,

CON.40M, and CON. 50M (CON. 5M)

BEEP / STROBE / BP+STR / BEAM /BP+BEM / CW

/ BP+CW / CWT

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

MANUAL / AUTO

50MS / 250MS / 450MS / 750MS /1000MS

---

50MS / 100MS

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

FW0.3S / FW0.5S / FW0.7S /

FW1.0S /FW1.5S

HOME / REV

DISABL / ENABLE

MORMAL / AUT.BCK

A VAILABLE V ALUES (D EFAULT : B OLD I TARIC

)

KEY 2S - KEY10S / CONT / OFF (KEY 5S)

KEY / PTT / KY (KEY)+PTT

MONI / T-CALL

OFF / 20MS / 50MS / 100MS / 200MS

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

ON / OFF

LVL 1 - LVL 9 (LVL 5)

OFF / KY+SCN / KEY

400 - 1000 Hz (50 Hz/step)

(700 Hz)

A

VAILABLE

V

ALUES

(D

EFAULT

: B

OLD

I

TARIC

)

---

OFF / DC / MSG

---

A VAILABLE V ALUES (D EFAULT : B OLD I TARIC

)

BAREXT / BARANT

±5 MHz / ±10 MHz / ±50 MHz / ±100 MHz

ON / OFF

EXTANT / EARPHO

---

---

ON / OFF

ON / OFF

ON / OFF

---

LVL 1 - LVL 9 (LVL 5)

OFF / 00H.10M(00:10) - 24H.00M(24:00)

(10 minutes/step)

---

AUTO / N-FM / AM / W-FM

SINGLE / CONT

AUTO / SPKR

ON / OFF

OFF / LVL 1 - LVL 8

AUTO / 5 / 8.33 / 9 / 10 / 12.5 / 15 / 20 /

25 / 50 / 100 kHz

STEREO / MONO

OFF / TRX 1S - TRX 10S (1S/step) /

HOLD / TX 1S - TX 10S (1S/step)

OFF / 0.5M - 10.0M (0.5M/step) (3.0M: 3 minutes)

ALL / BAND

ON / OFF

OFF / ON

VX-3R O

PERATING

M

ANUAL

107

S

ET

(M

ENU

) M

ODE

Set Mode Item 1 [ANT AM]

Function: Select the antenna to be used in the AM Broadcast listening.

Available Values: BAREXT/BARANT

Default: BAREXT

BAREXT: Uses both the internal Bar Antenna and the Rubber Flex Antenna.

BARANT: Uses the internal Bar Antenna only.

The Bar Antenna is directional; rotate the VX-3R for best reception.

Set Mode Item 2 [ANT FM]

Function: Select the antenna to be used in the FM Broadcast listening.

Available Values: EXTANT/EARPHO

Default: EXTANT

EXTANT: Uses the Rubber Flex Antenna.

EARPHO: Uses the Earphone Antenna. When receiving a weak signal, reception may be noisy.

Set Mode Item 3 [ANT.ATT]

Function: Enables/Disables the receiver Front-end Attenuator.

Available Values: ON/OFF

Default: OFF

Note: This Set Mode Item can select and set the function to each memory channel individually.

Set Mode Item 4 [APO]

Function: Setting of the Automatic Power-Off feature.

Available Values: OFF/0.5H - 12.0H (0.5H/steps)

Default: OFF

Set Mode Item 5 [ARS]

Function: Enables/Disables the Automatic Repeater Shift function.


Default: ON

Set Mode Item 6 [ARTSBP]

Function: Selects the Beep option during ARTS™ operation.

Available Values: OFF/IN RNG/ALWAYS

Default: IN RNG

OFF: No alert beeps sound.

IN RNG: Beeps sound only when the radio first detects that you are within range.

ALWAYS: Beeps sound every time a polling transmission is received from the other station (every 15 or 25 seconds when in range).

108 VX-3R O

PERATING

M

ANUAL

S

ET

(M

ENU

) M

ODE

Set Mode Item 7 [ARTSIT]

Function: Selects the Polling Interval during ARTS™ operation.

Available Values: 15SEC/25SEC

Default: 25SEC

Set Mode Item 8 [BCLO]

Function: Enables/Disables the Busy Channel Lock-Out feature.


Default: OFF

Set Mode Item 9 [BEL.RNG]

Function: Selects the number of Bell ringer repetitions.

Available Values: 1T - 20T/CONT (Continuous ringing)

Default: 1T

Set Mode Item 10 [BEL.SEL]

Function: Enables/Disables the Bell ringer function and its sound selection.

Available Values: OFF/BELL/USRBP1/ USRBP2/ USRBP3

Default: OFF


Set Mode Item 11 [BNK.NAM]

Function: Stores Alpha-Numeric “Tags” for the Memory Banks.

See page ?? for details.

Set Mode Item 12 [BP ED]

Function: Enables/Disables the Band-edge beeper while selecting the frequency by the

DIAL knob.


Default: OFF

Set Mode Item 13 [BP LVL]

Function: Adjust the Beep volume level.

Available Values: LVL 1 - LVL 9

Default: LVL 5

Set Mode Item 14 [BP SEL]

Function: Enables/Disables the Keypad beeper.

Available Values: OFF/KY+SCN/KEY

Default: KY+SCN

OFF: The Beeper is disabled.

KY+SCN: The beeper sounds when you press a key or when the scanner stops.

KEY: The beeper sounds when you press any key.

VX-3R O

PERATING

M

ANUAL

109

S

ET

(M

ENU

) M

ODE

Set Mode Item 15 [BP USR]

Function: Create the beep melody for Bell ringer function.

See page 38 for details.

Set Mode Item 16 [BSY.LED]

Function: Enables/Disables the BUSY LED while the Squelch is open.


Default: ON

Set Mode Item 17 [CH CNT]

Function: Selects the Channel Counter Search Width.

Available Values: ±5 MHz/±10 MHz/±50 MHz/±100 MHz

Default: ±5 MHz

Set Mode Item 18 [CLK.SFT]

Function: Shifting of the CPU clock frequency.


Default: OFF

Note: 1) This Set Mode Item can select and set the function to each memory channel individually.

2) This function is only used to move a spurious response “birdie,” should it fall on a desired frequency.

Set Mode Item 19 [CW ID]

Function: Programs and activates the CW Identifier (used during ARTS operation).


Set Mode Item 20 [CWLRNG]

Function: Enables/Disables the CW Learning feature.


Set Mode Item 21 [CWPICT]

Function: Select the CW tone pitch for the CW Learn, CW training, and CW Identifier functions.

Available Values: 400 - 1000 Hz (50 Hz/step)

Default: 700 Hz

Set Mode Item 22 [CWTRNG]

Function: Enables/Disables the CW Training feature.


Set Mode Item 23 [DC VLT]

Function: Indicates the DC Supply Voltage.

110 VX-3R O

PERATING

M

ANUAL

S

ET

(M

ENU

) M

ODE

Set Mode Item 24 [DCS CD]

Function: Setting of the DCS code.

Available Values: 104 standard DCS codes

DCS CODE

Default: DCS.023


023 025 026 031 032 036 043 047 051 053

054 065 071 072 073 074 114 115 116 122

125 131 132 134 143 145 152 155 156 162

165 172 174 205 212 223 225 226 243 244

245 246 251 252 255 261 263 265 266 271

274 306 311 315 325 331 332 343 346 351

Set Mode Item 25 [DCS RV]

Function: Enables/Disables the “Inverted”

DCS Tone.

356 364 365 371 411 412 413 423 431 432

445 446 452 454 455 462 464 465 466 503

506 516 523 526 532 546 565 606 612 624

Available Values: R-N.T-N/R-I.T-N/R-B.T-N/

R-N.T.I/R-I.T-I/R-B.T-I

627 631 632 654 662 664 703 712 723 731

732 734 743 754 –

Default: R-N.T-N

R-N.T-N: Receive and transmit the Normal DCS Tone.

– – – – –

R-I.T-N: Receive the Inverted DCS Tone and transmit the Normal DCS Tone.

R-B.T-N: Receive the both Normal and Inverted DCS Tones and transmit the Normal DCS

Tone.

R-N.T.I: Receive the Normal DCS Tone and transmit the Inverted DCS Tone.

R-I.T-I: Receive and transmit the Inverted DCS Tone.

R-B.T-I: Receive the both Normal and Inverted DCS Tones and transmit the Inverted

DCS Tone.


Set Mode Item 26 [DT A/M]

Function: Enables/Disables the DTMF Autodial feature.

Available Values: MANUAL/AUTO

Default: MANUAL

Set Mode Item 27 [DT DLY]

Function: Selects the DTMF Autodialer Delay Time.

Available Values: 50MS/250MS/450MS/750MS/1000MS

Default: 450MS

Set Mode Item 28 [DT SEL]

Function: Programming of the DTMF Autodialer.


Set Mode Item 29 [DT SPD]

Function: Selects the DTMF Autodialer Sending Speed.

Available Values: 50MS/100MS

Default: 50MS

VX-3R O

PERATING

M

ANUAL

111

S

ET

(M

ENU

) M

ODE

Set Mode Item 30 [EAI]

Function: Enables/Disables the Emergency Automatic ID (EAI) feature..


Default: OFF

Set Mode Item 31 [EAI.TMR]

Function: Sets the Emergency Automatic ID (EAI) operating mode and its Transmit Time.

Available Values:

INT. 1M through INT.10M, INT.15M, INT.20M, INT.30M, INT.40M, INT. 50M,

CON. 1M through CON.10M, CON.15M, CON.20M, CON.30M, CON.40M, and CON.

50M

Default: CON. 5M

Set Mode Item 32 [EMG.SEL]

Function: Select the alarms utilized when the Emergency function is engaged.

Available Values: BEEP/STROBE/BP+STR/BEAM/BP+BEM/CW/BP+CW/CWT

Default: BP+STR

BEEP (BP): Loud “Alarm” sounds.

STROBE (STB): Flashes the TX/BUSY indicator in bright white color.

BP+STB: Loud “Alarm” sounds along with flashing of the TX/BUSY indicator in white.

BEAM:

BP+BEM:

CW:

The TX/BUSY indicator glows continuously in white.

Loud “Alarm” sounds and the TX/BUSY indicator glows continuously in white.

The TX/BUSY indicator flashes according to the programmed Emer-

BP+CW:

CWT: gency message (Morse Code) Ú at a rate of five words per minute.

Sounds tones via the speaker, and flashes the TX/BUSY indicator, according to the programmed Emergency message (Morse Code) Ú at a rate of five words per minute.

Transmits the programmed Emergency message (Morse Code)* and flashes the TX/BUSY indicator, according to the programmed Emergency message (Morse Code) Ú on the air beginning one minute after activation of the Emergency function.

Ú: The internationally-recognized Morse Code “S.O.S” message (• • • – – – • • •) is programmed at the factory for the Emergency message.

Here’s how to program the Emergency Message:

1. Set this Set Mode Item to “CW ” or “BP+CW .”

2. Press the [V/M] key to display any previously-stored emergency message.

3. Press the [HM/RV] key to clear any previous emergency message, if desired.

4. Rotate the DIAL knob to select the first letter/number of the message, then press the

[V/M] key momentarily to save the first letter/number and move on to the next character.

112 VX-3R O

PERATING

M

ANUAL

S

ET

(M

ENU

) M

ODE

5. Repeat the previous step as necessary to complete the message (up to 16 characters).

6. If you make a mistake, press the [BAND] key to backspace the cursor; now re-enter the correct letter/number.


8. When you have entered the message, press the [TXPO] key momentarily to confirm the message, then press the PTT switch to save the settings and exit to normal operation.

Set Mode Item 33 [EXT.MNU]

Function: Enables/Disables the extended Set Mode Menu.


Default: OFF

Set Mode Item 34 [FW KEY]

Function: Set the duration that a secondary function of the [F/W] key (press and holding the [F/W] key) is held determines the function they activate.

Available Values: FW0.3S/FW0.5S/FW0.7S/ FW1.0S/FW1.5S

Default: FW0.5S

Set Mode Item 35 [HLF.DEV]

Function: Reducing the Deviation level by 50 %.


Default: OFF


Set Mode Item 36 [HM/RV]

Function: Selects the function of the [HM/RV] key.

Available Values: HOME/REV

Default: REV

HOME: Pressing the [HM/RV] key instantly recalls a favorite “Home” channel.

REV: Pressing the [HM/RV] key reverses transmit and receive frequencies during repeater operation.

Set Mode Item 37 [HM>VFO]

Function: Enables/Disables the function of the VFO DIAL knob, while in the Home Channel mode.

Available Values: DISABL/ENABLE

Default: ENABLE

VX-3R O

PERATING

M

ANUAL

113

S

ET

(M

ENU

) M

ODE

Set Mode Item 38 [INT CD]

Function: Selects the Access Number (DTMF digit) for the SRG operation of the Internet

Connection feature (WIRES™).

Available Values: DTMF 0 - DTMF F

Default: DTMF 1

Set Mode Item 39 [INT MD]

Function: Selects the operating mode of the Internet Connection feature (WIRES™).

Available Values: SRG/FRG

Default: SRG

Set Mode Item 40 [INT.A/M]

Function: Enables/Disables the DTMF Autodialer feature while operating using the Internet

Connection feature (WIRES™).

Available Values: MANUAL/AUTO

Default: MANUAL

Set Mode Item 41 [INT.SEL]

Function: Programming of the Access Number (DTMF code) for the FRG station of the

WIRES™ (or non WIRES™ Internet Link System) access.


Set Mode Item 42 [INTKEY]

Function: Selects the function of the [ ] key.

Available Values: INTNET/INT MR/SET MD

Default: INTNET

INTNET: The [ ] key activates/disables the internet feature.

INT MR: The [ ] key recalls the Internet Access Number (SRG) or Access String (FRG).

(SRG) or (FRG) is determined via Set Mode Item 39: INT MD .

SET MD: The [ ] key is the Short-cut path to recall one of the Set Mode Items. See page

92 for programming.

Set Mode Item 43 [INTNET]

Function: Enables/Disables the Internet Connection feature (WIRES™).


Default: OFF

114 VX-3R O

PERATING

M

ANUAL

S

ET

(M

ENU

) M

ODE

Set Mode Item 44 [LAMP]

Function: Selects the LCD/Keypad Lamp mode.

Available Values: KEY 2S - KEY10S/CONT/OFF

Default: KEY 5S (5 seconds)

KEY 2S - KEY10S: Illuminates the LCD/Keypad for the selected time, when any key is

CONT:

OFF: pressed.

Illuminates the LCD/Keypad continuously.

Disables the LCD/Keypad illumination

Set Mode Item 45 [LED LT]

Function: Illuminates the TX/BUSY indicator. It will glow continuously white (useful as emergency flashlight at night).

Set Mode Item 46 [LOCK]

Function: Selects the Control Locking lockout combination.

Available Values: KEY/PTT/KY(KEY)+PTT

Default: KEY

Set Mode Item 47 [M/T-CL]

Function: Selects the function of the MONI switch (just below the PTT switch) function.

Available Values: MONI/T-CALL

Default: Depends on the transceiver version.

MONI: Pressing the MONI switch will over ride the Noise/Tone Squelch, allowing you to listen for weak (or non-encoded) signals.

T-CALL: Pressing the MONI switch activates a 1750-Hz burst tone, used for repeater access in many countries (especially in Europe).

Set Mode Item 48 [MCGAIN]

Function: Adjust the microphone gain level.

Available Values: LVL 1 - LVL 9

Default: LVL 5

This Set Mode setting affects both internal and external microphones.

Set Mode Item 49 [MR DSP]

Function: Toggles the display indication between “frequency” and “Alpha/Numeric” channel tags.

Available Values: ALPHA/FREQ

Default: FREQ


VX-3R O

PERATING

M

ANUAL

115

S

ET

(M

ENU

) M

ODE

Set Mode Item 50 [MR WMD]

Function: Determines the method of selecting channels for Memory Storage.

Available Values: NEXT/LOWER

Default: NEXT

NEXT: Stores the data into the memory channel, which is next highest from the laststored memory channel.

LOWER: Stores the data into the next-available “free” channel.

Set Mode Item 51 [MRFSTP]

Function: Selects the channel step for the fast channel selection mode while in the Memory

Recall mode.

Available Values: 10CH/20CH/50CH/100CH

Default: 10CH

Set Mode Item 52 [MRNAME]

Function: Stores “Alpha-Numeric” tags for the Memory channels.



Set Mode Item 53 [MRPTCT]

Function: Enables/Disables the Memory Write Protector.


Default: OFF

When this function is set to “ON”, the memory write operation is ignored.

Set Mode Item 54 [MRSKIP]

Function: Selects the Memory Scan channel-selection mode.

Available Values: OFF/SKIP/ONLY

Default: OFF

OFF: All memory channels will be scanned (the “flag” will be ignored).

SKIP: The scanner will “skip” the flagged channels during scanning.

ONLY: The scanner will only scan channels that are flagged (Preferential Scan List).


Set Mode Item 55 [MSG.LST]

Function: Programming a Member List for the Message feature.


Set Mode Item 56 [MSG.REG]

Function: Selects your Personal ID for the Message feature.


116 VX-3R O

PERATING

M

ANUAL

S

ET

(M

ENU

) M

ODE

Set Mode Item 57 [MSG.SEL]

Function: Programming a Message for the Message feature.


Set Mode Item 58 [ON TMR]

Function: Set the On Timer Time.

Available Values: OFF/00H.10M(00:10) 24H.00M(24:00) (10 minutes/step)

Default: OFF

The On Timer turns on the radio at the programmed time.

Set Mode Item 59 [OPN.MSG]

Function: Selects the Opening Message that appears when the radio is powered on.

Available Values: OFF/DC/MSG

Default: DC

OFF: No Opening Message

DC: DC supply voltage

MSG: Set by user. See below.

Here’s how to program the Opening Message:

1. Select this Set Mode Item to “MSG.”

2. Press the [V/M] key momentarily to enable programming of the opening message. You will notice the first character entry’s location blinking.

3. Rotate the DIAL knob to select the first letter/number of the message, then press the

[V/M] key momentarily to save the first letter/number and move on to the next character.

Note: Do not forget to pull the DIAL knob to rotate the DIAL knob

4. Repeat the steps 3 and 4 as necessary to complete the message (up to six characters).

5. If you make a mistake, press the [BAND] key to back-space the cursor; now re-enter the correct letter/number.

6. When you have entered the desired opening message, press the [TXPO] key momentarily to confirm the message, then press the PTT switch to save the settings and exit to normal operation.

Set Mode Item 60 [PAG.ABK]

Function: Enables/Disables the Answer Back function of the Enhanced CTCSS Paging &

Code Squelch.


Default: OFF

Set Mode Item 61 [PAG.CDR]

Function: Sets the Receiver Pager Code for the Enhanced CTCSS Paging & Code Squelch.


VX-3R O

PERATING

M

ANUAL

117

S

ET

(M

ENU

) M

ODE

Set Mode Item 62 [PAG.CDT]

Function: Sets the Transmitting Pager Code for the Enhanced CTCSS Paging & Code

Squelch.


Set Mode Item 63 [PR FRQ]

Function: Program the CTCSS Tone frequency for the User programmed Reverse CTCSS

Decoder.

Available Values: 300Hz - 3000Hz (1000 Hz/step)

Default: 1600 Hz


Set Mode Item 64 [PRI.RVT]

Function: Enables/Disables the Priority Revert feature.


Default: OFF


Set Mode Item 65 [PRI.TMR]

Function: Selects the time between the Priority (Dual Watch) channel checks, when the feature is active.

Available Values: 0.1 - 0.9S (0.1S/step) or 1.0S - 10.0S (0.5S/step)

Default: 5.0S


Set Mode Item 66 [PSWD]

Function: Programs and activates the Password feature.


Set Mode Item 67 [PTT.DLY]

Function: Selects the time delay before the carrier is transmitted, when the PTT switch is pressed.

Available Values: OFF/20MS/50MS/100MS/200MS

Default: OFF

Set Mode Item 68 [RPT]

Function: Sets the Repeater Shift Direction.

Available Values: SIMP/-RPT/+RPT

Default: Depends on the transceiver version, as well as the setting of Set Mode Item 5

ARS .


118 VX-3R O

PERATING

M

ANUAL

S

ET

(M

ENU

) M

ODE

Set Mode Item 69 [RPT.SFT]

Function: Sets the magnitude of the repeater Shift.

Available Values: 0.00 - 150.00 MHz (50 kHz/step)

Default: Depends on the operating band and transceiver version.

If you press the [F/W] key momentarily, then rotate the DIAL knob, frequency steps of 1

MHz will be selected.


Set Mode Item 70 [RX MD]

Function: Selects the Receiving mode.

Available Values: AUTO/N-FM/AM/W-FM

Default: AUTO (Mode automatically changes according to operating frequency.)


Set Mode Item 71 [S SRCH]

Function: Selects the Smart Search Sweep mode.

Available Values: SINGLE/CONT

Default: SINGLE

SINGLE: The transceiver sweeps the current band once in each direction starting on the current frequency. All channels where activity is present (up to 15 in each direction) are loaded into the Smart Search memories. Whether or not all 31 memories are filled, the search stops after one sweep in each direction.

CONT: The transceiver makes a sweep in each direction as with the “SINGLE” mode, but if all 31 channels are not filled after the first sweep, the radio continues sweeping until they are all filled.

Set Mode Item 72 [SAVERX]

Function: Selects the Receive-mode Battery Saver interval (“sleep” ratio)


Default: 0.2 S (1:1)

Set Mode Item 73 [SAVETX]

Function: Enables/Disables the Transmitter Battery Saver.


Default: OFF

Set Mode Item 74 [SCN.LMP]

Function: Enables/Disables the Scan lamp (while scanner is paused).


Default: ON

VX-3R O

PERATING

M

ANUAL

119

S

ET

(M

ENU

) M

ODE

Set Mode Item 75 [SCN.RSM]

Function: Selects the Scan Resume mode.

Available Values: 2SEC - 10SEC/BUSY/HOLD

Default: 5 SEC

2 SEC - 10 SEC: The scanner will halt on a signal it encounters, and will hold there for the selected resume time. If you do not take action to disable the scanner within that time period, the scanner will resume even if the station is still

BUSY:

HOLD: active.

The scanner will halt on a signal it encounters. When the signal drops, the scanner will resume. The Scan resume time (default 2 seconds) is controlledset by the Set Mode Item 76: SCN.STR

.

The scanner will halt on a signal it encounters. It will not restart automatically; you must manually re-initiate scanning if you wish to resume.

Set Mode Item 76 [SCN.STR]

Function: Select the Scan Re-start Delay time.


Default: 2.0S

Set Mode Item 77 [SP OUT]

Function: Enables/Disables the FM Broadcast audio output to the internal speaker when using the earphone antenna.

Available Values: AUTO/SPKR

Default: AUTO

AUTO: The FM Broadcast audio output is selected automatically depending on the connection of the earphone antenna.

SPKR: Outputs the FM Broadcast audio output to the internal speaker any time.

Set Mode Item 78 [SQ LVL]

Function: Sets the Squelch threshold level.

Available Values: LVL 0 - LVL 15 (AM and Narrow FM), LVL 0 - LVL 8 (Wide FM and

AM Broadcast)

Default: LVL 1 (AM and Narrow FM), LVL 2 (Wide FM and AM Broadcast)

120 VX-3R O

PERATING

M

ANUAL

S

ET

(M

ENU

) M

ODE

Set Mode Item 79 [SQ TYP]

Function: Selects the Sub Audible Squelch Type.

Available Values: OFF/TONE/TSQL/DCS/RV TN/PR FRQ/PAGER/MESSAGE

Default: OFF

TONE: Activates the CTCSS Encoder

TSQ:

DCS:

Activates the CTCSS Encoder/Decoder

Activates the Digital Coded Encoder/Decoder

RV TN: Activates the Reverse CTCSS Decoder (Mutes the receiver when matching tone is received)

PR FRQ: Activates the User programmed Reverse CTCSS Decoder (Mutes the receiver when the matching tone programmed with Set Mode Item 63: PR FRG is received)

PAGER: Activates the Enhanced Paging & Code Squelch

MESSAGE: Activates the Message feature

Note: 1) This Set Mode Item can select and set the function to each memory channel individually.

2) See also Set Mode Item 81: SQSPLT regarding additional selections available during

“Split Tone” operation.

Set Mode Item 80 [SQSMTR]

Function: Adjusts the Squelch threshold to the S-meter level.

Available Values: OFF/LVL 1 - LVL 8

Default: OFF


Set Mode Item 81 [SQSPLT]

Function: Enables/Disables split CTCSS/DCS coding.


Default: OFF

When this Set Mode Item is set to “ON,” you can see the following additional parameters after the “MESSAGE” parameter while selecting the Set Mode Item 79: SQ TYP .

D CODE: DCS Encode only.

T DCS: Encodes a CTCSS tone and Decodes a DCS code.

D TONE: Encodes a DCS code and Decodes a CTCSS tone.

Select the desired operating mode from the selections shown above.

VX-3R O

PERATING

M

ANUAL

121

S

ET

(M

ENU

) M

ODE

Set Mode Item 82 [STEP]

Function: Setting the Dial frequency steps.

Available Values: AUTO/5/8.33/9/10/12.5/15/20/25/50/100 kHz

Default: AUTO (Step automatically changes according to operating frequency.)

Note: 1) This Set Mode Item can select and set the Dial frequency steps to individual memory channels when Memory Offset Tuning is enabled as shown on page 46.

2) 9 kHz steps are available only when receiving on the BC band.

3) 8.33 kHz steps are available only when receiving on the Air band.

4) While operating on the BC band, you may only select channel steps of 9 kHz or 10 kHz; the other step selections are disabled.

5) 5 kHz steps are not available for use on 250 - 300 MHz, nor above 580 MHz.

Set Mode Item 83 [STEREO]

Function: Enables/Disables the stereo output, while receiving the FM Broadcast band.

Available Values: STEREO/MONO

Default: STEREO


Set Mode Item 84 [SUB-RX]

Function: Sets the time before Broadcast audio is resumed after the amateur band signal drops, when the AF Priority function is activated.

Available Values: OFF/TRX 1S - TRX 10S (1S/step)/HOLD/ TX 1S - TX 10S (1S/step)

Default: OFF

TRX 1S - TRX 10S: Broadcast audio is resumed 1 to 10 seconds after the received signal

HOLD: drops or your Transmission ends

Broadcast audio is not resumed after the receive signal drops or your transmission ends.

TX 1S - TX 10S: Broadcast audio is resumed 1 to 10 seconds after your Transmission ends. Audio is resumed immediately when the received signal drops.

Set Mode Item 85 [TEMP]

Function: Indicates the current temperature inside the transceiver’s case and selects the measurement units (“°F” or “°C”) for the temperature sensor.

Press the [MODE] key to toggle the measurement units between “°F” and “°C”.

122 VX-3R O

PERATING

M

ANUAL

S

ET

(M

ENU

) M

ODE

Set Mode Item 86 [TN FRQ]

Function: Setting of the CTCSS Tone Frequency.

CTCSS TONE FREQUENCY (Hz)

67.0

69.3

71.9

74.4

77.0

79.7

Available Values: 50 standard CTCSS tones

Default: 100.0 Hz

82.5

85.4

88.5

91.5

94.8

97.4

100.0

103.5

107.2

110.9

114.8

118.8

Set Mode Item 87 [TOT]

Function: Setting of the TOT time

Available Values: OFF/0.5M - 10.0M (0.5M/

123.0

127.3

131.8

136.5

141.3

146.2

151.4

156.7

159.8

162.2

165.5

167.9

171.3

173.8

177.3

179.9

183.5

186.2

189.9

192.8

196.6

199.5

203.5

206.5

step)

Default: 3.0M (3 minutes)

210.7

218.1

225.7

229.1

233.6

241.8

250.3

254.1

– – – –

The time-out timer shuts off the transmitter after continuous transmission of the programmed time.

Set Mode Item 88 [TS MUT]

Function: Enables/Disables the receiver audio output while the Tone Search Scanner is activated.


Default: ON

Set Mode Item 89 [TS SPD]

Function: Selects the Tone Search Scanner speed.

Available Values: SLOW (1.25 tone/sec)/FAST (2.5 tone/sec)

Default: FAST

Set Mode Item 90 [VFO MD]

Function: Selects or disables the VFO band edge limiting for the current band.

Available Values: ALL/BAND

Default: BAND

BAND: When the VFO frequency reaches the high band edge of the current band, the

VFO frequency will jump to the low band edge of the current band (or vice versa).

ALL: When the VFO frequency reaches the high edge of the current band, the VFO frequency will jump to the low band edge of the next band (or vice versa).

Set Mode Item 91 [VFO.SKP]

Function: Set the My Band.


Default: OFF

The “My Band” feature allows you to select several operating bands, and make only those bands available for selection via the [BAND] key.

ON: Only the bands that are turned on will be shown when pushing the [BAND] key.

OFF: When the [BAND] key is pressed, the bands that are turned “OFF” will not be shown.


VX-3R O

PERATING

M

ANUAL

123

S

ET

(M

ENU

) M

ODE

Set Mode Item 92 [VOL MD]

Function: Select the DIAL knob function.

Available Values: NORMAL/AUT.BCK

Default: NORMAL

NORMAL: The [VOL] key keeps the status while pressing the [VOL] key.

AUT.BCK: The [VOL] key to keep the status approximately three seconds after pressing the [VOL] key.

Set Mode Item 93 [WAKEUP]

Function: Setting of the Wakeup feature.

Available Values: OFF/5SEC - 60SEC(5SEC/step)/EAI

Default: OFF

Set Mode Item 94 [WX ALT]

Function: Enables/Disables the NOAA Weather Alert Feature.

Available Values: OFF/ON

Default: OFF

124 VX-3R O

PERATING

M

ANUAL

N

OTE

VX-3R O

PERATING

M

ANUAL

125

S

PECIFICATIONS

General

Frequency Ranges:

(USA Version)

Channel Steps:

Frequency Stability:

Repeater Shift:

Emission Type:

Antenna Impedance:

Supply Voltage:

Current Consumption:

RX 0.5-1.8 MHz (AM Broadcast)

1.8-30 MHz (SW Band)

30-76 MHz (50 MHz HAM)

76-108 MHz (FM Broadcast)

108-137 MHz (Air Band)

137-174 MHz (144 MHz HAM)

174-222 MHz (VHF TV)

222-420 MHz (ACT1)

420-470 MHz (430 MHz HAM)

470-800(729) MHz (UHF TV)

(757-774) MHz (UHF TV)

800-999.99 MHz (GEN2; USA Cellular Blocked)

TX 144-146(148) MHz

430-440(450) MHz

5/9/8.33/10/12.5/15/20/25/50/100 kHz

±5 ppm (–10 °C to +60 °C)

±600 kHz (144 MHz)

±1.6/5.0/7.6 MHz (430 MHz)

F2D, F3E, F2A

50 Ω

Nominal: 3.7 V DC, Negative Ground

Operating: 3.7 ~ 7.0 V, Negative Ground (EXT DC Jack)

5.0 ~ 7.0 V, Negative Ground (EXT DC Jack w/Charging)

120 mA (Receive)

60 mA (Standby, Saver Off)

30 mA (Standby, Saver On, Save Ratio 1:2)

50 mA (Radio Band Receive)

100 μA (Auto Power Off)

1.3 A (1.5 W Tx , 144 MHz) 3.7 V DC

1.6 A (3 W Tx , 144 MHz) 6 V DC

1.2 A (1 W Tx , 430 MHz) 3.7 V DC

1.8 A (2 W Tx , 430 MHz) 6 V DC

Operating Temperature: –20 °C to +60 °C

Case Size (W x H x D):

Weight:

1.9” x 3.2” x 0.9” (47 x 81 x 23 mm) (W/O knob & antenna)

4.6 oz (130 g) With FNB-82LI & antenna

Specifications are subject to change without notice, and are guaranteed within the 144 and

430 MHz amateur bands only. Frequency ranges will vary according to transceiver version; check with your dealer.

126 VX-3R O

PERATING

M

ANUAL

S

PECIFICATIONS

Transmitter

RF Power Output: 1.5 W (@ 4.5 V AA x 3 or 3.7 V FNB-82LI 144 MHz)

3 W (@ 6 V or EXT DC 144 MHz)

1 W (@4.5 V AA x 3 or 3.7 V FNB-82LI 430 MHz)

2 W (@ 6 V or EXT DC 430 MHz)

Modulation Type:

Maximum Deviation:

Spurious Emission:

Low 0.1 W (@ 4.5 V AA x 3 or 3.7 V FNB-82LI)

Low 0.3 W (@ 6 V or EXT DC)

Variable Reactance F2D , F3E, F2A

±5 kHz (F2D , F3E)

At least 60 dB below (HIGH)

At least 50 dB below (LOW or less than 1 W)

Microphone Impedance: 2 kΩ

Receiver

Circuit Type: AM, NFM: Double-Conversion Superheterodyne

WFM: Triple-Conversion Superheterodyne

AM Radio/FM Radio: Single-Conversion Superheterodyne

Intermediate Frequencies: 1st: 47.25 MHz (AM, NFM)

1st: 45.8 MHz (WFM)

1st: 130 kHz (AM Broadcast/FM Broadcast)

2nd: 450 kHz (AM, NFM)

2nd: 10.7 MHz (WFM)

Sensitivity:

Selectivity:

AF Output:

3rd: 1 MHz (WFM)

3 μV for 10 dB SN (0.5-1.8 MHz, AM Broadcast)

3 μV for 10 dB SN (1.8-30 MHz, AM)

0.35 μV TYP for 12 dB SINAD (30-54 MHz, NFM)

1 μV TYP for 12 dB SINAD (54-76 MHz, NFM)

3 μV TYP for 12 dB SINAD (76-108 MHz, FM Broadcast)

1.5 μV TYP for 10 dB SN (108-137 MHz, AM)

0.2 μV for 12 dB SINAD (137-140 MHz, NFM)



1 μV TYP for 12 dB SINAD (174-225 MHz, NFM)




1.5 μV for 12 dB SINAD (470-540 MHz, WFM)

3 μV TYP for 12 dB SINAD (540-800 MHz, WFM)

1.5 μV TYP for 12 dB SINAD (800-999 MHz, NFM)

USA Version Cellular Blocked

NFM, AM: 12 kHz/35 kHz (–6 dB /–60 dB)

WFM : 200 kHz / 300 kHz (–6 dB/–20 dB)

50 mW @ 8 Ω for 10 % THD (@ 3.7 V)

100 mW @8 Ω for 10 % THD (@ 6 V)

VX-3R O

PERATING

M

ANUAL

127

R

ESET

P

ROCEDURES

In some instances of erratic or unpredictable operation, the cause may be corruption of data in the microprocessor (due to static electricity, etc.). If this happens, resetting of the microprocessor may restore normal operation. Note that all memories will be erased if you do a complete microprocessor reset, as described below.

M

ICROPROCESSOR

R

ESETTING

To clear all memories and other settings to factory defaults:

1. Turn the radio off.

2. Press and hold in the [MODE] and [V/M] keys while turning the radio on.

3. Press the [F/W] key momentarily to reset all settings to their factory defaults (press any other key to cancel the Reset procedure).

S

ET

M

ODE

R

ESETTING

To reset the Set Mode Item Ú settings to their factory defaults:

1. Turn the radio off.

2. Press and hold in the [BAND] and [V/M] keys while turning the radio on.

3. Press the [F/W] key momentarily to reset the Set (Menu) mode settings to their factory defaults (press any other key to cancel the Reset procedure).

Ú: Except the following Set Mode Items

3: ANT.ATT, 10: BEL.SEL, 11: BNK.NAM, 18:CLK.SFT, 19: CW ID,

24: DCS CD, 28: DT SEL, 32: EMG.SEL, 35: HLF.DEV, 38: INT CD,

41: INT.SEL, 49: MR DSP, 52: MRNAME, 54: MRSKIP, 55: MSG.LST,

56: MSG.REG, 57: MSG.SEL, 61: PAG.CDR, 62: PAG.CDT, 68: RPT,

69: RPT.SFT, 79: SQ TYP, 80: SQSMTR, and 86: TN FRQ

128 VX-3R O

PERATING

M

ANUAL

1. Changes or modifications to this device not expressly approved by VERTEX

STANDARD could void the user’s authorization to operate this device.

2. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference including received, interference that may cause undesired operation.

3. The scanning receiver in this equipment is incapable of tuning, or readily being altered, by the User to operate within the frequency bands allocated to the Domestic public Cellular Telecommunications Service in Part 22.

DECLARATION BY MANUFACTURER

The Scanner receiver is not a digital scanner and is incapable of being converted or modified to a digital scanner receiver by any user.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR

RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES

AND FEDERAL LAW.

Copyright 2007

VERTEX STANDARD CO., LTD.

All rights reserved.

No portion of this manual may be reproduced without the permission of

VERTEX STANDARD CO., LTD.

Printed in Japan

E H 0 2 8 M 1 0 0

YAESU VX-3R Operating Manual

VHF/UHF

PERATING

ANUAL

General

Transmitter

Receiver

Related manuals

Table of contents

YAESU VX-3R Operating Manual

VHF/UHF

PERATING

ANUAL

General

Transmitter

Receiver

Related manuals

YAESU

VX-3E

Vertex Standard

VX-150

YAESU

VX-120 Series

YAESU

VR-160

Vertex Standard

VX-150

YAESU

VX-170

Yaesu Musen

K6620215X20

Vertex Standard

Yaesu VX-2R

YAESU

VX-6R-E

Vertex Standard

K6620285X20

Table of contents