Bosch RS-232 Installation guide

RS232 KIT
Installation
Guide
Building Block Video Ltd.,
17 Apex Park
Diplocks Industrial Estate,
Hailsham, East Sussex, BN27 3JU UK.
Tel: +44 (0)1323 842727
Fax: +44 (0)1323 842728
Support: +44(0)1323 444600
Web Site: www.bbvcctv.com
TABLE OF CONTENTS
1. Pre-installation Checks and Safety Procedures
Unpacking
Important safety precautions
3
3
3
2. Introduction
5
5
6
Technical Specification
Connection Information
3. System schematic diagrams
Fig. 2 Integration between the Interllex and the CTI16 card.
7
7
Fig. 3 List of cameras and Receivers that can be controlled by a CTI.
8
Fig.4 RS232 Kit Being used to connect the Tx1500 to the Laptop when
using the Upload Download GUI.
9
Fig.5 RS232 Kit Being used to connect the Tx1500 to the Laptop when
Reprogramming the Tx1500 Matrix.
10
Fig.6 RS232 Kit Being used to connect an Rx45X & Rx55X to a
Laptop when reprogramming the Receiver.
11
RS232 Kit V2.doc
Page 2/12
PRE-INSTALLATION CHECKS AND SAFETY PROCEDURES
UNPACKING
Check Packaging - Upon taking delivery of the unit, inspect the packaging for signs of
damage. If damage has occurred, advise the carriers and/or the suppliers immediately.
Check Contents - Upon taking delivery of the unit, unpack the receiver carefully and check
that all the items are present and correct. If any items are missing or damaged, contact your
equipment dealer.
Retain Packaging - The shipping carton is the safest container in which to transport the unit.
Retain undamaged packaging for possible future use.
IMPORTANT SAFETY PRECAUTIONS
Read Instructions - All relevant safety, installation and operating instructions should be read
before attempting to install, connect or operate the unit.
Retain Instructions - All safety, installation and operating instructions should be retained for
future reference.
Heed Warnings - All warnings on the unit and in any relevant safety, installation or operating
instructions should be adhered to.
Cleaning - Unplug the unit from the power outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
Attachments - Do not use attachments not recommended by the product manufacturer as
they may cause hazards.
Water and Moisture - Do not expose this unit to water or dampness; for example, in an
unprotected outdoor installation, or in any area classified as a wet location.
Power Sources - This unit should be operated only from the type of power source indicated
on the manufacturer’s label. If you are not sure of the type of power supply you intend to
use, consult your equipment dealer or local power company. For units intended to operate
from battery power or other sources, refer to operating instructions.
Overloading - Do not overload outlets and extension cords, as this can result in fire or
electric shock.
Object and Liquid Entry - Never push objects of any kind into the unit, as they may touch
dangerous voltage points or short out parts that could result in fire or electric shock. Never
spill liquid of any kind on or inside the unit.
Servicing - Servicing of the unit should only be undertaken by qualified service personnel, as
opening or removing covers may expose you to dangerous voltages or other hazards.
Damage Requiring Service - Servicing by qualified personnel should be carried out under
the following conditions:
RS232 Kit V2.doc
Page 3/12
(a) When the power-supply cord or plug is damaged;
(b) If liquid has been spilled, or objects have fallen into, the unit;
(c) If the internal electronics of the unit have been exposed to rain or water;
(d) If the unit does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions, as improper adjustment
of other controls may result in damage and will often require extensive work by a qualified
technician to restore the unit to normal operation;
(e) If the unit has been dropped or the enclosure is damaged;
(f) If the unit exhibits a distinct change in performance. This indicates a need for service.
Replacement Parts - If replacement parts are required, ensure that only replacement parts
recommended by the product manufacturer are used.
Safety Check - Upon completion of any service or repairs to the unit, safety checks should
be performed to ensure that the unit is in proper operating condition.
Pre-installation Checks - It is recommended that the unit be bench-tested prior to
installation on the site.
Adhere to Safety Standards - All normal safety precautions as laid down by British
Standards and the Health and Safety at Work Act should be observed.
WARNING
TO PREVENT DANGER OF FIRE OR SHOCK, DO NOT EXPOSE THE INTERNAL
COMPONENTS OF THIS EQUIPMENT TO RAIN OR MOISTURE.
The “lightning flash with arrowhead” symbol inside an equilateral triangle is used to warn the
user of this equipment that there are sufficiently high voltages within the enclosure to
constitute a risk of electric shock.
The “exclamation point” symbol inside an equilateral triangle is used to alert the user of this
equipment to important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
RS232 Kit V2.doc
Page 4/12
Technical Specification
Power Requirements
Input
Outputs
Facilities
9Vdc 500mA
RS232
1x Full Duplex RS422
2 front panel diagnostic LEDs
Items included in this kit
1 x TxLD
1 x 9VDC 500mA PLUG TOP PSU
1 x SA-PL61-1 RS232 Null Modem cable (female 9 pin D-Type to female 9 pin D-Type cable)
General introduction
This unit turns RS232 to RS422 & RS422 to RS232 full duplex. It can be used to interface a PC based DVR
with the
CTI 8 or 16.
The RS232 Kit is also used for programming a number of BBV systems Tx1500, Starcard Converter, BBUS
Interface, Tx.MK2.TPO, CTI-8 & CTI-16, and Rx45X & Rx55X.
Because it does not Modify the data it is also can be used when Debugging RS422 & RS485 data systems.
In This manual there are a few examples how the RS232 can be utilised. There are a number of drawings on
the BBV Support website www.support.bbvcctv.com showing the uses of the RS232 kit.
RS232 Kit V2.doc
Page 5/12
Connection Information
RS422 Full Duplex connections
RS232 Full Duplex connections
5
TA DATA + out
GND
8
9
TB DATA - out
4
GND
TX DATA out
7
3
RA DATA + in
RX DATA in
1
6
2
RB DATA - in
RS232 Kit V2.doc
Page 6/12
Sensormatic
Mark Mercer
JVC TK_C676
Coax to Dome
Pelco Domes
Pelco Esprit
Bosch Domes
All Dennard Domes
Panasonic
Aritech
LG Domes
VCL
Honeywell
RS485 to Dome
RG59 <250M
Rx100
CT125 <500M
1 Rx100 Per Dome
CTI-16
16 Camera Coax
Telemetry Interface
Fig. 2 Integration between the Interllex and the CTI-16 card.
RS232 Kit V2.doc
Page 7/12
R
L
H
T
X
IO
X
Edgeport/1
USB Converter
TxLD
RS232 to RS422
Converter
Forward
Vision
Sensormatic
Mark Mercer
JVC TK_C676
Pelco Domes
Pelco Esprit
Bosch Domes
All Dennard Domes
Panasonic
Please note this is a small selection of the domes that can
be controlled by the BBV Rx100 . For a full list of dome
Coax to Dome
RS485 to Dome
please refer to the BBV website www.bbvcctv.com. It is
important that the Rx100 must be close to the dome within 5
RG59
meter is recommend. The CTI Card can all so control the
Rx100
full range of BBV Receivers
Aritech
LG Domes
VCL
Honeywell
<250M
CT125 <500M
RX200
AC output, Wash, Wipe, Lights for static cameras
1 Rx100 Per Dome
RX300
AC output, Pan/Tilt/Zoom/Focus + choice of Wash, Wipe,
Lights or Autopan, Random Pan.
CTI-8
8 Camera Coax
Telemetry Interface
RX400P
AC output, Pan/Tilt/Zoom/Focus/Iris, Wash, Wipe, Lights,
Autopan, 16 presets, Preset patrol
RX45X
Advanced Telemetry Receiver – fixed speed AC P/T head.
32 presets, 8 alarm inputs, OSD programming menu.
Remote gain control. Selectable between 230Vac or
110Vac supply. 12Vdc 500mA camera supply output. Links
selectable mains or 24Vac output. Wash, Wipe, Lights and
Autopan outputs.
RX55X
As RX45X to drive 24Vdc high/variable speed P/T head.
Wash, Wipe and Lights outputs.
Fig. 3 List of cameras and Receivers that can be controlled by a CTI (Coax Telemetry Interface)
RS232 Kit V2.doc
Page 8/12
Forward
Vision
USE THE TELEMETRY PORT TO
PROGRAM MATRIX
The Tx1500 can have all its configuration
uploaded & Downloaded from a PC
running a BBV Program. With this
application you can also assigned camera
tittles & Alarm configuration.
Laptop computer
PCB0313 Iss2
BBV
RX
NOT
USED
TX
Fig.4 RS232 Kit Being used to connect the Tx1500 to the Laptop when using the Upload Download GUI.
RS232 Kit V2.doc
R
X
L
O
HI
T
X
GND
TB/-(OUT)
TA/+(OUT)
RA/+(IN)
RB/-(IN)
BN / W
W / BN
GN / W
W / BL
BL / W
W / GN
OR / W
W / OR
Page 9/12
USE BBUS PORT TO
PROGRAM MATRIX
Programming LINK found at the rear of Matrix
you will need to remove rear panel
PCB0313 Iss2
BBV
RX
R
X
L
O
HI
T
X
GND
TB/-(OUT)
TA/+(OUT)
RA/+(IN)
RB/-(IN)
BN / W
W / BN
GN / W
W / BL
BL / W
W / GN
OR / W
W / OR
NOT
USED
TX
Laptop computer
Fig.5 RS232 Kit Being used to connect the Tx1500 to the Laptop when reprogramming the matrix.
RS232 Kit V2.doc
Page 10/12
Local Self Test
Press UP & DOWN together.
Sequence is Left, Right, Down, Up,
Zoom In, Out, Focus Near, Far, Lights,
AutoPan, Wash, Wipe
UP
RS422/485 Termination links
LOGIC/UPPER BOARD CONNECTIONS
SELECT DOWN
= Terminated. End Of Line.
Status LED
ON = Power Present & processor running.
Blinking OFF = Valid data with Rx557 address.
J9-ALARMS
J7-PRESET
J11
PROG 1 2 3 4 5 6 7 8
8 7 6 5 4 3 2 1
a
ALARM IN
Volts Free
N/C Contacts
at
era D
2 Cam
RS42
ALARM OUT
Volts Free
N/C Contact
Alarm I/P 8
Alarm I/P 7
1
F
O
C
U
S
Z
O
O
M
P T
A I
N L
T
J10-LENS J4
J1-VIDEO
Lens drive LEDS
1 2 3 4 5 6
ZOOM OUT
ZOOM IN
TO CONTROLLER
I
R
I
S
*
F
O
C
U
S
Z
O
O
M
J4
RS485
Telemetry
1
2
3
4
5
T
R
A
T
R
B
G
N
D
R
A
R
B
Expanded
View
In Programming Mode
Prog link must be
connected
PCB0313 Iss2
BBV
LD2-RX
GND
TBTA+
RA+
RB-
RXRX
LOLO
HIHI
TXTX
LD1-TX
Fig.6 RS232 Kit Being used to connect an Rx45X & Rx55X to the Laptop when reprogramming the Receiver.
RS232 Kit V2.doc
FOCUS FAR
FOCUS NEAR
FROM CAMERA
12Vdc
Out
0.75A
2 3 4 5
T T G
R R N R R
A B D A B
= Un-Terminated. Daisy Chained.
Page 11/12
TO PC/Laptop via 9 Way
D type Lead Supplied
Laptop computer
Other BBV products.
Product Description
camera desktop telemetry transmitter with BBV up-the-coax &
TX300 Single
20mA telemetry, Pan/Tilt/Lens & Lights
TX400
TX400DC/RS485
TX1000 MK2
TX1500
FBM range
RX100
RX100/BAX
RX200
RX300
RX400P
RX45X (AC)
RX55X (DC)
Multi RS485 protocol
and BBV up-the-coax
telemetry receivers
RX450/550
CTI16
CTI8
STARCARD
STARCARD/CONVERTER
ACCESSORIES
As TX300 inc Wash, Wipe, Autopan, 8 presets, preset patrol.
As TX400 including joystick for proportional Pan/Tilt control with
RS485 Output.
8 or 16 camera, 2 monitor telemetry transmitter. Up to 2 keyboards.
BBV up-the-coax and RS422 standard with options for alarm inputs
and 20mA telemetry.
Mid size matrix 16 – 96 camera, 8 monitor. Up to 4 control positions
(keyboard & remote control) options for alarms, remote control, BBV
up-the-coax and RS485 telemetry.
Large size matrix. Configurable up to 4096 cameras and 64 monitor
outputs. Up to 16 control positions (keyboard & remote control)
options for alarms, remote control RS485/RS422 telemetry with
various options. Please call to discuss requirements.
Dome Interface with options to drive a large library of dome cameras.
BBV up-the-coax and 20mA telemetry.
Dome Interface with options to drive a large library of dome cameras.
BAXALL up-the-coax telemetry.
AC receiver for Pan only heads or static cameras, Wash/Wipe/Lights.
BBV up-the-coax and 20mA telemetry.
AC receiver for Pan/Tilt/Zoom/Focus/Iris Override and 1 Auxiliary
output. BBV up-the-coax and 20mA telemetry.
AC full function receiver. PTZFI 4 Auxiliary outputs, 16 presets. BBV
up-the-coax and 20mA telemetry.
Multiple RS485/422 and BBV up-the-coax controllable AC and DC
receivers. These receivers are controlled from an expanding range of
serial protocols as listed below. 110/230Vac supply. PTZFI, 64
presets, preset patrol, 8 local alarm inputs, 12V 500mA supply output.
OSD for remote diagnostics. 3 Aux. outputs RX55X or 4 Aux. outputs
RX45X.
Optional Privacy board.
BBV RS485, COAX & 20mA,
BAXALL COAX, DENNARD RS485,
MOLYNX, PELCO P/D RS485,
VCL/HONEYWELL RS485,
PHILIPS/BOSCH RS485 (OPTIONAL BI-PHASE INPUT),
SENSORMATIC/AD RS422
VICON RS422 & CIRRUS AUDIO MONITORING
PANASONIC RS485 Protocol only version of RX45X/55X.
Multi-protocol serial converter that gives either 8 or 16 channels of upthe-coax control (BBV Coax protocol). BBV RS422, Dennard RS485,
Pelco P, Pelco D, Philips/Bosch RS485/232, VCL RS485,
Sensormatic RS422, Molynx, Vicon
8 * RS485 output, 2 wire simplex RS422, 4 wire full-duplex RS422,
2 wire half-duplex RS485.
Optional STARCARD/CONVERTER offering protocol conversion to
drive an increasing range of 3rd party protocols.
TxLD (bidirectional RS422-RS232 converter)
98005 (bidirectional 20mA-RS232 converter)
AD RS422 (American Dynamics) protocol converters