Samsung SCD-3083 User manual

Super High Resolution WDR
Dome Camera
User Manual
SCD-3083
␃
㢜
■
■
Super High Resolution WDR Dome Camera
User Manual
Copyright
© Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document
shall be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but
no formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on
the user’s own responsibility. Samsung Techwin reserves the right to change the contents of this document
without prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve
the problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
• If the system behaves abnormally because you run a program irrelevant to the system operation.
• Deteriorated performance or natural worn-out in process of time
™ Design and specifications are subject to change without prior notice.
⏥
Before operating the camera, confirm the camera model and correct input power voltage.
To help you understand this manual thoroughly, we’ll introduce our model description.
■ SCD-3083 SERIES
• NTSC MODEL
SCD-3083N
• PAL MODEL
SCD-3083P
■ MODEL DESCRIPTION
• SCD-3083X
_
SIGNALSYSTEM
•SIGNAL SYSTEM
N→NTSC MODEL
P→PAL MODEL
Safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric
shock is present within this unit.
This exclamation point symbol is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
WARNING
• To prevent damage which may result in fire or electric shock hazard, do not expose this
appliance to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance
with the installation instructions.
8
9
1
ᔔ
1
2
3
4
5
6
7
WARNING
8
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
9
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
1
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause
abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. insecure connection may cause
fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause
personal injury.
4_ Safety information
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers
filled with water on top of the camera. doing so may cause personal injury due to fire,
electric shock, or falling objects.
8. If any unusual smells or smoke come from the unit, stop using the product. in such case,
immediately disconnect the power source and contact the service center. continued use in
such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. never
disassemble or modify this product in any way. (samsung is not liable for problems caused
by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. doing so may cause
fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location
subject to excessive vibrationor magnetic interference.
2. Do not install in a location subject to high temperature (over 55°C), low temperature (below
-10°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then
move or reinstall it.
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do so
may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this
may damage the CCD image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
10. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CCD.
English_5
● SAFETY INFORMATION
7. Do not install the unit in humid, dusty, or sooty locations. doing so may cause fire or
electric shock.
Safety information
fCC sTATemeNT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause
undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian
Interference.-Causing Equipment Regulations of ICES-003.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their
working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate these items from other types of waste and recycle them responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste at the end of their working life. Where marked, the chemical symbols
Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to human health
or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste
and recycle them through your local, free battery return system.
6_ Safety information
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus
15. This product is intended to be supplied by a Listed Power Supply Unit marked "Class 2" and
rated from 24Vac, 50 or 60 Hz / 12Vdc, min. 0.35A
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to provide
customers with more environment-friendly products.The Eco mark represents
Samsung Techwin’s will to create environment-friendly products, and indicates
that the product satisfies the EU RoHS Directive.
English_7
● SAFETY INFORMATION
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the
cart/ apparatus combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as powersupply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
1.
2.
3.
4.
5.
6.
7.
Contents
INTRODUCTION
9
10
11
Features
What’s included
Component names and Functions
12
14
Installation
Adjust the monitoring direction
of the camera
CONNECTION
15
15
16
Connecting to Monitor
Connecting to Power
Using coaxial communications
SETUP
18
18
Menu Configration
Menu Setup
34
Troubleshooting
3
Specifications
37
Dimension
9
INsTAllATION
12
15
18
TROUBLESHOOTING
34
SPECIFICATIONS
35
8_ Contents
⮈
FEATURES
ᄔ
 high Resolution
By adopting a diagonal 6mm (1/3”) 520,000 pixel (NTSC), 610,000 pixel (PAL)
SONY CCD, the camera produces clear picture quality with a horizontal resolution
of max 700 TV lines(665TVL±5%) for color ER mode and 700 TV lines for BW.
 excellent sensitivity
The built-in high sensitivity COLOR CCD produces a clear image.
y
- Color : 0.1 Lux (50IRE, @F1.2), 0.0002LUX (SENS-UP, x512)
- B/W : 0.01 Lux (50IRE, @F1.2), 0.00002 LUX (SENS-UP, x512)
 6615 (samsung super Noise Reduction) function
The high-performance SV-V DSP chip effectively removes low-light gain noise
and afterimage to provide clear images even in dark environments.
● INTRODUCTION
Introduction
 day & Night
This camera has a function that automatically selects the mode that is appropriate
for daytime or night-time conditions. The COLOR mode operates in daytime
conditions to provide optimum colors, and B/W mode operates in night-time conditions
to enhance the definition of the image.
 Intelligence
Without assistance from an external sensor, this camera independently detects and
traces objects while examining stillness and movement to activate the alarm.
 ssdR (samsung super dynamic Range)
For images with high contrast between bright and dark areas from difficult lighting
conditions such as backlighting, this camera selectively illuminates darker areas while
retaining the same light level for brighter areas to even out the overall brightness.
y
y
y
 miscellaneous functions
HLC (High Light Compensation), SENS-UP, REVERSE, D-ZOOM, SHARPNESS and
PRIVACY functions are provided.
y
 Communication
Coaxial communication methods are supported.
- Protocol : Pelco Coaxitron
y
 Osd
The camera control is convenient by using 17 different foreign language O.S.D.
- NTSC : English, Japanese, Spanish, French, Portuguese, Korean
- PAL : English, French, German, Spanish, Italian, Chinese, Russian, Polish,
Czech, Romanian, Serbian, Swedish, Danish, Turkish, Portuguese
English_9
Introduction
 WDR
By adopting a proprietary SV-V DSP chip, the camera delivers clear, high quality pictures
even when the scene is backlight, by increasing exposure in dark areas while decreasing
it in bright areas; a corrected image with clear details results.
 Vps(Virtual progressive scan)
Adopting Samsung's unique development, the VPS(Virtual Progressive Scan) enhances
the sharpness of moving subject's outline. The VPS enables elective output in progressive
mode using the existing interlaced input and effectively enhances the sharpness of
captured pictures from video and still images. The function effectively removes blurred
outline problems resulting in excellent road monitoring and improved license plate
recognition.
 DIs (Digital Image stabilizer)
The DIS function compensates for any camera movement, to produce more
stable pictures.
WHAT’S INCLUDED
Check if the following items are included in the product package.
Super High Resolution WDR Dome Camera
Quick Set-up Guide
Camera
Video Output Cable
10_ Introduction
SCD-3083
Quick Manual
Tapping Screw 3EA
COMPONENT NAMES AND FUNCTIONS
2
4
➌
● INTRODUCTION
❶
ಲ
y
y
➐
➏
5
T
OU N)
D_ _D )
(M (EXT ND
D
(G
RE HITE K
W AC
BL
⓬
⓫
❿
➒
➑
2 shield Case
❶ Dome Cover
➌ Pan Base : control panning angle of camera
4 2.8 Vari-focal Lens Module 3 ~ 8.5 mm (F1.2)
5 Function Setup Switch : Display the OSD menu and move the cursor up, down, left,
and right amend or confirm changes.
When menu is off, move this switch left(NEAR) or right(FAR)
for adjusting focus. move this switch up(TELE) or down(WIDE)
for adjusting zoom. Short to press this button to fit the focus
automatically.
➏ Video Output Terminal to Monitor
➐ Rotate base : control rotating angle of camera.
➑ Power Input Connector
➒ Ground Terminal
❿ D & N Input Terminal : You can switch to Day & Night Mode by connecting
an external signal to this terminal.
⓫ MD Output Terminal: Motion detection signals are output through this terminal.
⓬ Video Output Jack
M
 Be sure to connect the Day & Night input terminal to GND when using an external input.
English_11
Installation
BEFORE INSTALLATION
Before installing your camera, you have to read the following cautions :
• You have to check whether the location (ceiling or wall) can bear five times the weight of your camera.
• Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise
it may cause a breakdown or fire.
• Before installing your camera, you have to adjust the lens focus, zoom, and switch settings.
• When installing your camera, don’t allow any person to approach the installation site. If you have any
valuable things under the place, move them away.
INSTALLATION
1. Separate the dome cover by turning anti-clockwise and separate the shield case by pulling from
the camera body.
Main Body
(Camera)
Shield Case
Latch
Unlocking direction
(Anti-clockwise)
Locking direction
(Clockwise)
Dome cover
12_ Installation
2. Hold the ceiling bracket (located where the arrow points to) and separate it from the main body of
the camera by rotating it anti-clockwise.
3. Place the separated ceiling bracket so that the “Front” side faces the area to be monitored
and install it with the M4 tapping screws.
tapping
screw
tappingscrew
* If you want to install the camera with the ceiling
bracketcombined,fixitusingtwotapping screws
atthesideofthemainbody
4. To combine the main body with the ceiling bracket, make sure that the pan base fixation screw
face the opposite side of the “Front” side of the ceiling bracket and rotate it clockwise.
5. Adjust the camera lens to face the area to be monitored and fix the main body and
the dome cover by aligning the grooves and rotating the body clockwise.
English_13
●INSTALLATION
Ceilingbracket
PanBase
fixation
screw
Installation
Adjusting the monitoring direction for the camera
Pan
Tilt
Lens rotation
 Adjusting the monitoring direction
You can adjust the camera direction only when the camera is fixed on the ceiling.
Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt
is called Tilt, and turning the lens on its axis is called Rotation.
- The effective range of pan is a total of 352 degrees.
- The effective range of rotation is a total of 348 degrees.
- The effective range of tilt is a total of 73 degrees.
J
 The image can be covered up by the camera case depending on the angle.
 Do not forcefully turn the focus/zoom lens after the dome case is disassembled.
Otherwise, it may cause an incorrect focus due to a motor failure.
 Methods of adjustment
1. After installing the camera, adjust the panning angle in consideration of the
monitoring direction.
2. Set the horizontal angle so that the image is not reversed.
3. Adjust the tilt angle so that the camera faces toward the monitoring object.
14_ Installation
Connection
⻸
CONNECTING TO MONITOR
ಲ
Connect the Video OUT port on the rear panel of the camera to a monitor.
㎫
● CONNECTION
Monitor
Camera
 As the connecting method varies with the instruments, refer to the manual supplied
with the instrument.
 Only connect the cable when the power is turned off.
y
CONNECTING TO POWER
Since power specifications differ depending on the model, make sure to check your model name
and specifications before connecting power.
You can connect power as shown in the following figure.
y
ಲ
---- Power Input Terminal
6
㎫
※
When the resistance value of copper wire is at [20°C(68°F)]
PP PP PP PP PP PP
Resistance ( Ω /m)
Voltage Drop (V/m)
Copper wire size (AWG)
 As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively
long adaptor output line for connection to the camera may affect the performance of the camera.
* Standard voltage for camera operation :DC 12V ±10%, AC 24V ±10%
* There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
English_15
Connection
 Be sure to connect power only after all the installation is complete.
 Note that AC / DC adaptor is not supplied with camera.
 Ground should be connected to the GND terminal.
Using coaxial communications
• Coaxial Communications System
• OSD Control method
• If you set the sensitivity level of the sub menu item (of COAX) to “Low”, you have to
press the MENU/ENTER (OSD KEY) button twice in a row to access the OSD menu.
(To prevent an error by noise from the DVR)
CAMERA
DVR
SET
MENU/ENTER
CONTROLLER
OSD KEY
UP
UP KEY
JOYSTICK UP
DOWN
DOWN KEY
JOYSTICK DOWN
LEFT
LEFT KEY
JOYSTICK LEFT
RIGHT
RIGHT KEY
JOYSTICK RIGHT
DVR
ALARM
1
5
DVD RECORDER
OPEN/CLOSE
HDD
NETWORK
2
6
BACKUP
3
7
REC
REC
4
8
9
10
11
12
13
14
15
16
ZOOM
FREEZE BACKUP SEARCH
TELE
WIDE
VIEW
MODE
AUDIO
ALRAM
PRESET
MENU
USB
RETURN
•
16_ Connection
: BNC
- Video Cable
The camera's video output port is connected to the monitor with a BNC coaxial cable,
shown below : If the distance between the camera and the monitor exceeds the
recommended maximum, please use an auxiliary video amp.
Recommended Cable Specification
300m
3C2V(RG-59/U)
450m
5C2V(RG-6/U)
600m
7C2V(RG-11/U)
 It is recommended that pure copper coax cable is used and not copper coated
steel, as this will cause issues with the communication over the coaxial cable.
 To ensure picture quality, only single-channel video output connector can be
used while camera connected to other video equipments.
English_17
● CONNECTION
Distance
ಲ
y
y
Setup
MENU CONFIGRATION
MAIN SETUP
LENS
● DC
EXPOSURE
● BRIGHTNESS
● SENS-UP
● SHUTTER
● RETURN
● AGC
SSDR
● OFF
● ON
WHITE BAL
● ATW
● MANUAL
● OUTDOOR
● AWC→SET
● INDOOR
BACKLIGHT
● OFF
● WDR
● USER BLC
● HLC
SSNR3
● ON
● OFF
DAY/NIGHT
● AUTO
● B/W
● EXTERN
● COLOR
SPECIAL
● IMAGE ADJ
● INTELLIGENCE
● PROFILE
● CAM TITLE
● PRIVACY
● COAX
● SYNC
● DIS
● RETURN
EXIT
● SAVE
● NOT SAVE
● RESET
meNU seTUp
Use the Function Setup switch within the camera.
EO
VID
Function Setup switch
▶
1. Press the Function Setup switch.
y Main setup menu is displayed on the monitor screen.
18_ Setup
㔤
Select the function using
the Function Setup switch.
‫ܓ‬
DC
Change the status
using the Function
Setup switch.
OFF
ATW
OFF
ON
AUTO
● SETUP
MAIN SETUP
䯝 1.LENS
2.EXPOSURE
3.SSDR
4.WHITE BAL
5.BACKLIGHT
6.SSNR3
7.DAY/NIGHT
8.SPECIAL
9.EXIT
SAVE
2. Select a desired function using the Function Setup switch.
y Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.
 An item with the
icon also has sub menus. To select a sub menu, select an item with the icon
and press the Function Setup switch.
 An item with the - - - icon is unavailable due to function settings.
‫ܓ‬
LENS
㖳
Using this function, you can control the screen brightness.
1. When the SETUP menu screen is displayed, select ‘LENS’ by using the Function
Setup switch so that the arrow indicates ‘LENS’.
2. DC : You can adjust the minimum shutter and
maximum value of ESC shutter mode.
3. The Lens mode has sub menu items as listed below.
y Brightness : Adjusts the video brightness.
y FOCUS ADJ : To adjust the DC lens focus
correctly, you must activate the Focus Settings
mode under each lens menu. Activate the Focus
Settings mode, adjust the lens focus, and then
deactivate the settings mode.
DC LENS
▶1. BRIGHTNESS
*
IIIIIIIII IIIIIIII
25
2. FOCUS ADJ
3. RETURN
FOCUS ADJ
▶1. SIMPLE FOCUS
2. AFTER D/N
3. RETURN
OFF
English_19
Setup
- SIMPLE FOCUS : Select this to fit the focus automatically.
- AFTER D/N : After D or N is switched, select whether to use the focus
readjustment function.
- RETURN : Select this to save the changes in the FOCUS ADJ menu and return to
the DC LENS menu.
y RETURN : Select this to save the changes in the DC LENS menu and return to the
SETUP menu.
EXPOSURE
1. When the SETUP menu screen is displayed, select EXPOSURE by using the Function
Setup switch so that the arrow indicates 'EXPOSURE'.
2. Select a desired mode using the Function
EXPOSURE SETUP
Setup switch.
䯝 1.BRIGHTNESS IIIIIÂIIIIIIIIIIIIIIII 25
 BRIGHTNESS : Adjusts the video brightness.
2.SHUTTER
ESC
 SHUTTER : You can select the shutter.
3.AGC
HIGH
- ESC : Select this to control the shutter
4.SENS-UP
OFF
speed automatically. If ESC is selected,
5.RETURN
the shutter speed is automatically
controlled depending on the ambient illumination of the subject.Shutter speed
will change between MIN and MAX by setting.
 MIN : 1/50~1/60000
 MAX : 1/00~1/20000
- MANUAL : You can control shutter speed manually.
(NTSC MODEL - 1/60sec~1/120,000sec, PAL MODEL - 1/50sec~1/120,000sec)
- A.FLK : Select this when you experience picture flicker, this happen when there is
a clash with the installed lighting frequency.
- --- : Shutter speed is fixed.
 When the SHUTTER is set to ESC after selecting the Internal Synchronization Type, the picture may
become unstable if the camera faces a bright fluorescent light. Therefore, take care when choosing
the installation position.
 When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
 Set the shutter mode to --- if color rolling occurs.
20_ Setup
y AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen - but
the greater the noise.
- HIGH : Allows automatic gain control from 5.3dB to 42dB.
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 5.3dB to 32dB.
y RETURN : Return to the SETUP menu.
 If you press the Function Setup switch in ‘AUTO’ mode, You can adjust brightness by adjusting
the SENS-UP level. (x2 ~ x512)
 Note that the higher the SENS-UP level, the brighter the screen, but the more likely it is that an
after-image will appear.
 It is normal for Noise, Spots and Whitish symptoms to appear in SENS-UP mode when the
D-ZOOM level is increased.
SSDR (Samsung Super Dynamic Range) :
SSDR illuminates darker areas of an image while retaining the same light level for brighter areas
to even out the overall brightness of images with high contrast between bright and dark areas.
1. When the SETUP menu screen is displayed,
SSDR SETUP
select SSDR by using the Function Setup
IIIIIIIIIIIÂIIIIIIIIII
8
䯝 1. LEVEL
switch so that the arrow indicates 'SSDR'.
y OFF : Deactivates the SSDR function.
Press SET to Return
y ON : Activates the SSDR function.
- Use the Function Setup button to change the SSDR level in the sub menu according
to the contrast between bright and dark areas.
SSDR ON
SSDR OFF
English_21
● SETUP
y SENS-UP : When it is night or dark, the camera automatically detects the light level and
maintains a clear picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO : Activates the SENS-UP function.
Setup
WHITE BAL (WHITE BALANCE)
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ‘White Bal’ by using the Function
Setup switch so that the arrow indicates ‘White Bal’.
2. Select a desired mode using the Function Setup switch.
※ Select one of the following 5 modes, as appropriate for your purpose.
y ATW : Select this when the color temperature is between 2,400˚K and 10,500˚K.
y OUTDOOR : Select this when the color temperature is between 1,700˚K and 11,000˚K.
(sodium light inclusion) Select this When the color temperature of environment
surrounding the subject is out of the control range (e.g. clear sky, or sunset)
y INDOOR : Select this when the color temperature is between 4,500˚K and 8,500˚K.
y MANUAL : Select this to fine-tune White
Balance manually. Set White
Balance first by using the ATW
or AWC mode. After that switch
to MANUAL mode, fine-tune the
White Balance and then press
the Function Setup switch.
WB MANUAL
䯝 RED GAIN IIIIIIIIIIII*IIIIIIIIIIIIII 117
BLUE GAIN IIIIIIIIIIIIIIIII*IIIIIIIIII 193
Press SET to Return
y AWC→SET : To find the optimal luminance level for the current environment,
point the camera towards a sheet of white paper and press the
Function Setup switch. If the environment changes, readjust it.
 White Balance may not work properly under the following conditions.In this case select the AWC
mode.
1 When the color temperature of the environment surrounding the subject is out of
the control range (e.g. clear sky or sunset).
2 When the ambient illumination of the subject is dim.
➌ If the camera is directed towards a fluorescent light or is installed in a
place where illumination changes dramatically, the White Balance
operation may become unstable.
22_ Setup
BACKLIGHT
● SETUP
The camea is designed so that it delivers a distinctive subject and background at
the same time, even when the subject is in backlight, by adopting a function of the
proprietary SV-V DSP chip.
1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by using
the Function Setup button. so that the arrow indicates ‘BACKLIGHT’.
2. Select a desired mode using the Function Setup button depending on the
camera purpose.
y OFF : Not being used
y USER BLC : Enables a user to select a desired
area on a picture and view that area more clearly.
- LEVEL : Adjusts the brightness level of a
monitoring area.
- TOP/BOTTOM/LEFT/RIGHT :
Adjust the area to be enhanced.
BLC SETUP
䯝 1. LEVEL
2. TOP
3. BOTTOM
4. LEFT
5. RIGHT
6. RETURN
MIDDLE
30
100
IIIÂIIIIIIIIIIIIIIIIII
75
IIIIIIIIIIIIIIIIÂIIIII 140
IIIÂIIIIIIIIIIIIIIIIII
IIIIIIIIIIIIIIIIÂIIIII
y HLC (High Light Compensation) :
HLC SETUP
This function masks the strong light to minimize
MIDDLE
white out due to over exposure and preserve much 䯝 1. LEVEL
NIGHT ONLY
2. LIMIT
of the on-screen details when the camera aims a
BLACK
3. MASK COLOR
strong light source.
ÂIIIIIIIIIIIIIIIIIIIII
4. MASK TONE
5
IÂIIIIIIIIIIIIIIIIIIII
- LEVEL : Adjusts the brightness level of a
10
5. TOP
monitoring area.
6. BOTTOM IIIIIIIIIIIIIIIIIIÂIII 120
IÂIIIIIIIIIIIIIIIIIIII
10
7. LEFT
- LIMIT : Enable to change the operating condition.
IIIIIIIIIIIIIIIIIIIÂII 210
8. RIGHT
- MASK COLOR/TONE : Change the
9.
RETURN
color / brightness of the masking area.
(Black, Red, Blue, Cyan, Magenta)
- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced.
y WDR : When there are both bright and dark areas at the same time, this mode makes
both areas distinctive.
- LIMIT : Adjust the WDR Sensitivity by
selecting LOW, MIDDLE, or HIGH.
- LEVEL : Adjust the WDR Brightness by
controlling the bar from 1 to 10.
- MODE : Indoor and outdoor backlight
conditions are appropriately selected.
- ANTI ROLLING : Rolling caused around a
fluorescent lamp is improved.
WDR SETUP
䯝 1. LIMIT
2. LEVEL
3. MODE
4. ANTI ROLLING
MIDDLE
IIIIIIIIIÂIIIIIIIIIIII
5
INDOOR
OFF
5. RETURN
English_23
Setup
WDR ON
WDR OFF
M
Because there can be a difference in the effectiveness of HLC according to the amount of light
area in the screen, optimize the installation angle for the best HLC performance.
 In a dark environment, the HLC is only activated when a high light that is larger than a certain area
is present.
 The HLC is not activated in day light or when bright light is not present at night. (In NIGHT ONLY
mode).
 Since the performance of the WDR function may be affected by the area of the bright part of the
screen, optimize the installation angle for the best WDR performance.
 If you increase LIMIT, the screen display may be distorted.
 If you use the VPS (Virtual Progressive Scan) function, the CCD reads differently so you can not use
WDR simultaneously. If you set VPS to ON, WDR will be automatically set to FIXED Mode.
6615
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select 'SSNR3' by using the Function
Setup switch so that the arrow indicates 'SSNR3'.
2. Select a desired mode using the Function Setup
SSNR3
switch.
IIIIIIIIIIIIIIIIIIIII 15
▶ LEVEL
 Off : Deactivates SSNR3. Noise is not reduced.
 ON : Activates SSNR3 so that noise is reduced.
Press SET to Return
3. Set the SSNR3 mode to 'ON' and press the Function Setup switch.
4. Then you can adjust the noise reduction level.
 You cannot set the SSNR3 to 'ON' or 'OFF' when the AGC mode of the EXPOSURE
menu is 'OFF'.
 When adjusting the noise reduction level of the SSNR3 mode, remember that the higher
the level set, the more the noise level will be reduced but that after image may also occur.
24_ Setup
DAY/ NIGHT
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the Up
and Down buttons so that the arrow indicates ‘DAY/NIGHT’.
- BURST MODE : You can turn on or off the
burst signal on B/W mode.
- DURATION : You can select the brightness
level at which the camera switches from day
to night mode.
- DWELL TIME : You can select the duration
time about changing the day/night mode.
→3s, 5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s
AUTO SETUP
▶1.BURST MODE
2.COLORB/W
DURATION
DWELL TIME
3.B/WCOLOR
DURATION
DWELL TIME
4.RETURN
ON
FAST
5 SEC
FAST
10 SEC
y EXTERN : Ground to the grounding terminal to allow automatic switching between
COLOR and B/W.
 COlOR : The picture is always displayed in color.
 b/W : The picture is always displayed in black and white. You can turn on or off the
burst mode on B/W mode.
 When AGC in the EXPOSURE menu is set to OFF, AUTO mode is not available to select.
 When using an external input, Connect the D & N Input Port to the Ground Terminal.
English_25
● SETUP
2. Select a desired mode using the Left and Right buttons according to the picture display
you want.
 AUTO : The mode is switched to ’Color‘ in a normal environment, but switches to
‘B/W’ mode when ambient illumination is low. To set up the switching time
for AUTO mode, press the Function Setup switch. You can turn on or off
the burst signal on B/W mode.
Setup
SPECIAL
1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function Setup
switch so that the arrow indicates ‘SPECIAL’.
2. Select a desired mode using the Function Setup
SPECIAL
switch.
#䯝 1.IMAGE ADJ
2.CAM TITLE
3.SYNC
4.INTELLIGENCE
5.PRIVACY
6.DIS
7.PROFILE
8.COAX
9.RETURN
 ImAGe ADJ :
1) When the SPECIAL menu screen is
displayed, select ‘IMAGE ADJ’ by using
the Function Setup switch so that the
arrow indicates ’IMAGE ADJ‘.
2) Select a desired mode using the Function
Setup switch.
- monitor : Please change the settings
value of video appropriate to
your monitor.
 LCD
OFF
INT
OFF
OFF
OFF
BASIC
ON
IMAGE SETUP
▶ 1. MONITOR
LCD
2.VPS
OFF
3.REVERSE
OFF
4.PIP
OFF
5.D-ZOOM
OFF
6.FONT COLOR
BLUE
7.SHARPNESS
ON
8.LANGUAGE
ENGLISH
9.RETURN
LCD MONITOR
: Please select this menu item when
using an LCD monitor. You can
䯝 GAMMA
0.55
IIÂIIIIIIIIIIIIIIIIIII 14
change the gamma, PED level and # PED LEVEL
IIIIIIIIIIÂIIIIIIIIIII 5
color gain in the sub menus.
COLOR GAIN
#
RESET
: Please select this menu item when
using a CRT monitor. You can
Press SET to Return
change the PED level, color gain in
the sub menus.
 USER : Please use this menu item when using a monitor other than standard ones. You can change the gamma, PED level and color gain
in the sub menus.
 CRT
26_ Setup
- D-ZOOM : You can use a digital zoom
of x1 ~ x16.
● SETUP
- VPS(Virtual Progressive Scan) :
This is an advanced technology that reproduces a sharp progressive image. This is
appropriate to high quality recording and file transfer via the Internet.
• OFF : Selects 2:1 Interlaced Scan as the Imaging Method.
• ON : Selects Progressive Scan as the Imaging Method.
- REVERSE : You can reverse the picture.
• OFF : You don’t reverse the picture.
• H-REV : You can flip the picture horizontally on the screen.
• V-REV : You can flip the picture vertically on the screen.
• HV-REV : You can flip the picture horizontally and vertically on the screen.
- PIP(Picture in Picture) : Displays a full-size
PIP SETUP
image along with the thumbnail to provide
IIIIIIIIIIIIIIIIIIIIIIIIIIIÂIIII 17
䯝 1. X POS
more detailed information. The position of
IIIIIIIIIIIIIIIIIIIIIIIIIIIÂIIII 17
2. Y POS
the thumbnail is adjustable.
3. RETURN
- FONT COLOR : You can change the OSD
font color. (White, Yellow, Green, Red, Blue)
- SHARPNESS : As you increase this value,
the picture outline becomes stronger and
clearer. Adjust this value appropriately
depending on the sharpness of the picture.
 OFF: Turn off Sharpness function.
SHARPNESS
䯝 Level
IIIIIIIIIIIIIIIIÂIIIIIIIIIIIIIII 10
Press SET to Return
ON : The higher the level is,the sharper and
clearer the outline of the image becomes.
 ER (Enhanced Resolution) : Choosing this mode can increase the sharpness of the picture
under the colour mode.

- LANGUAGE : You can select the menu language according to your requirements.
- RETURN : Return to the SPECIAL menu.
M
 When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
 If you increase the SHARPNESS level too high, the picture may become distorted or noise may
appear.
English_27
Setup
y CAM TITLE : If you enter a title, the title will
appear on the monitor.
CAMERA TITLE SETUP
2) Set it to ‘ON’ by using the Function Setup
button.
A B C
N O P
a b c
n o p
- . 0
← →
3) Press the set button.
_______________
1) If the SPECIAL menu screen is displayed, use
the Function Setup button so that the arrow
indicates ‘CAM TITLE’.
D E
Q R
d e
q r
1 2
CL
F G H I J K L M
S T U V W X Y Z
f g h i j k l m
s t u v w x y z
3 4 5 6 7 8 9
R POS END
4) Use the Function Setup button to move
to a desired letter and select the letter by pressing the set button. Repeat this
to enter multiple letters. You can enter up to 15 letters.
5) Enter a title, move the cursor to ‘POS’ and press
the set button. The entered title appears on the
screen. Select the position to display the title on
the screen by using the Function Setup button
and press the set button. When the position
is determined, select ‘END’ and press the set
button to return to the SPECIAL menu.
M
FRONT DOOR
 When the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you enter one.
 and Numbers are available in this mode.
 If you move the cursor to CLR and press the set button, all the letters are deleted. To edit a letter,
change the cursor to the bottom left arrow and press the set button. Move the cursor over the
letter to be edited, move the cursor to the letter to be inserted and then press the set button.
y SYNC : In areas where the supply is at
SYNC
60Hz(NTSC), 50Hz(PAL) frequency,
ÂIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 0
䯝 PHASE
you can synchronize the output
phase of multiple cameras using
Press SET to Return
the power synchronization function (Line-Lock) without using a
synchronization signal generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
1) Press the set button.
2) You can select a desired phase from 0 to 359 when select 'phase'.
M
 When using AC power at 60Hz(NTSC), 50Hz(PAL) frequency, you can use the L/L type
synchronization.
 When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.
 If the VPS is set to ON, synchronization is fixed to INT.
28_ Setup
y INTELLIGENCE :
Commands the camera to motion-detect and
trace an object.
- MOTION : Select motion types to detect.
• DETECTION : Since the camera
detects motion without any additional
external sensor, you can monitor
activity more efficient.
• TRACKING : Commands the camera
to detect and trace a moving object.
- FENCE : You can select up to 4
FENCE.
- MODE : Determines whether to use
the fence selected in the FENCE.
- TYPE : Two types, line and area,
of fences are available.
OFF
ON
OFF
IIIIIIIIÂIIIIIIII
IIIIIIIIÂIIIIIIIII
3
3
TRACKING
䯝 1. FENCE
2. MODE
3. TYPE
4. COUNT
5. FILL
# 6. POSITION
7. RETURN
FENCE1
OFF
LINE
OFF
OFF
- COUNT : Displays how many times
a subject passes over the fence on the screen.
- FILL : Fill or remove color from the FENCE.
- POSITION :Defines the position and detection direction of a line or
fenced area.
1) LINE FENCE
- SEL POS : Selects a position from
POS1,POS2.
LINE FENCE
1. SEL POS
- X POS / Y POS : Adjust the size and 2. X POS
position of the selected line fence. 3. Y POS
4. DIRECTION
POS1
IIIIIIIIIIIIIIIIIIIII 12
IIIIIIIIIIIIIIIIIIIIIIIII 1
- DIRECTION
5. RETURN
y DIR1 : Detects objects moving left
to right on the fence line.
y DIR2 : Detects objects moving right to left on the fence line.
y DIR1/2 : Detects all objects moving crosswise on the fence line.
DIR1
- RETURN : Return to the TRACKING menu.
English_29
● SETUP
• OFF : Not being used.
INTELLIGENCE
䯝 1. MOTION
2. DETECT BOX
3. ALARM OUT
4. DETECT AREA
5. MASK AREA
# 6. SENSITIVITY
# 7. DETECT SIZE
8. RETURN
Setup
2) AREA FENCE
- SEL POS : Selects a position from
AREA FENCE
POS1 ~ POS4.
1. SEL POS
POS1
- X POS / Y POS : Adjust the size
IIIIIIIIIIIIIIIIIIIII 12
2. X POS
and position of the selected area
IIIIIIIIIIIIIIIIIIIIIIIII 1
3. Y POS
fence.
4. DIRECTION
IN
- DIRECTION
5. RETURN
y IN : Detects objects entering the
fenced area.
y OUT : Detects objects exiting the fenced area
y IN/OUT : Detects all objects entering and exiting the fenced area.
- RETURN : Return to the TRACKING menu.
- RETURN: Return to the INTELLIGENCE menu.
• FIXED/MOVED : Detects an object that emerges or disappears from the
screen, or stays onscreen without movement.
M
 A detection (FIXED/MOVED) error may occur if :
- multiple motions occur continuously in random directions
- a fixed object moves in one position continuously
- a second object screens the first moving object
- DETECT BOX : Outlines an object on the screen in a box when its movement
matches a custom Motion Type.
- ALARM OUT : Releases a signal from the MD Output Port on the back of the
camera when an object’s movement matches a custom Motion Type.
- DETECT AREA : Motion Detection and
DETECT AREA
tracking will only occur within this defined
ÂIIIIIIIIIIIIIIIIIIIII
1
䯝 1.TOP
area. (Full Screen is defined as factory
IIIIIIIIIIIIIIIIIIIIIÂ
50
2.BOTTOM
default).
ÂIIIIIIIIIIIIIIIIIIIII
1
3.LEFT
- MASK AREA : Specify a detection
IIIIIIIIIIIIIIIIIIIIIÂ
4.RIGHT
50
exception area to mask.Select a mask area
5.RETURN
number and specify the size and position.
• AREA : You can select up to 4 areas.
• MODE : Determines whether to use
the area selected in the
AREA.
• TOP / BOTTOM / LEFT / RIGHT :
Adjust the size and position of the
selected area.
30_ Setup
MASK AREA
䯝 1.AREA
2.MODE
3.TOP
4.BOTTOM
5.LEFT
6.RIGHT
7.RETURN
IIIIIÂIIIIIIIIIIIIIIII
IIIIIIIIIIIIÂIIIIIIIII
ÂIIIIIIIIIIIIIIIIIIIII
IIIIIIIIIIIIÂIIIIIIIII
AREA1
OFF
30
110
25
110
• RETURN : Select this to save the MASK AREA menu settings and return
to the INTELLIGENCE menu.
- SENSITIVITY : Set the sensitivity of the motion detection. When you adjust the
lower level, the more sensitive.
- RETURN : Return to the SPECIAL menu.
y PRIVACY :
Mask an area you want to hide on the screen.
1) When the SPECIAL menu screen is
PRIVACY AREA SETUP
displayed, press the set button so that
䯝 1. AREA
AREA1
the arrow indicates ‘PRIVACY’.
2.
MODE
OFF
2) Set up the mode using the Function
3.
MASK
COLOR
GREEN
Setup button.
4. TRANSPARENCY
OFF
- AREA : You can select up to 12 PRIVACY areas.
L_TOP
5. SEL POS
- MODE : Determines whether to use the
ÂIIIIIIIIIIIIIIIIIIIII
10
6. X POS
area selected in the AREA.
ÂIIIIIIIIIIIIIIIIIIIII
10
7. Y POS
- MASK COLOR : Determine area color.
8. RETURN
You can select Green, Red, Blue, Black,
White, Gray.
- TRANSPARENCY : Adds or removes transparency from the masking area.
- SEL POS/ XPOS/ YPOS : Adjust the size and position of the selected area.
- RETURN : Return to the SPECIAL menu.
y DIS (Digital Image Stabilizer) : This function mitigates any picture movement due to
external factors such as wind.
M
 As the DIS function uses the digital zoom, the camera's resolution will decrease.
 DIS doesn’t operate when background illumination is too low.
 DIS doesn’t operate when object pattern is monotonic as like sky or white wall.
English_31
● SETUP
- DETECT SIZE : Selects an object size to detect on the screen. When you
adjust higher levels, the more larger size.
⥂
Setup
y PROFILE : Select a desired mode using
the Function Setup switch according to
the picture display
- BASIC : The most common environment
is set to meet.
- DAY/NIGHT : It will be set automatically
so it optimizes to the day or night
conditions, respectively.
- BACKLIGHT : It will be set automatically
SPECIAL
1.IMAGE ADJ
2.CAM TITLE
3.SYNC
4.INTELLIGENCE
5.PRIVACY
6.DIS
#䯝 7.PROFILE
8.COAX
9.RETURN
ড়
OFF
INT
OFF
OFF
OFF
BASIC
ON
so you can distinguish the object from
the background in a severe backlighting scene.
- ITS : It will be set automatically so you can easily check the traffic conditions.
- INDOOR : It will be set automatically to help you take a picture in a regular
indoor lighting condition.
- USER : Automatically configures the camera to your custom settings.
1) Select Custom for Simple Setup mode.
2) Configure the menu options to your custom settings.
3) The settings are automatically saved as Custom mode.
4) Profile user mode don't initialize when menu resets.
* In the PROFILE menu, you can configure the following camera settings at
once.
SHUTTER
GAIN
WHITE BAL
BACKLIGHT
SSNR3
DAY/NIGHT
32_ Setup
BASIC
ESC
HIGH
ATW
OFF
ON
AUTO
DAYNIGHT BACKLIGHT
ITS
ESC
ESC
MANUAL(1/250)
HIGH
HIGH
HIGH
ATW
ATW
OUTDOOR
OFF
USER BLC
OFF
ON
ON
ON
AUTO
AUTO
AUTO
INDOOR
A.FLK
HIGH
INDOOR
OFF
ON
AUTO
USER
-
y COAX : You can select whether to use COAX
communication.
If you use the COAX communication, you
prevent malfunctions by selecting low
sensitivity levels against noise.
COAX SENSITIVITY
䯝 1.SENSITIVITY
2. RETURN
LOW
● SETUP
y RETURN : Return to the MAIN SETUP menu.
EXIT
Select a desired EXIT mode using the Function Setup button depending on the
camera purpose.
y SAVE : Save the current settings and exit the MAIN SETUP menu.
y NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu.
y RESET : Resets the camera settings to the factory defaults. Communication,
Language and Monitor settings are not initialized.
English_33
Troubleshooting
TROUBLESHOOTING
If you have trouble operating your camera, refer to the following table. If the guidelines do not enable
you to solve the problem, contact an authorized technician.
PROBLEM
SOLUTION
Nothing appears on the screen.
▶ Check that the power cord and line connection between the
camera and monitor are fixed properly.
▶ Check that you have properly connected VIDEO cable to the
camera VIDEO output jack.
The image on the screen is dim.
▶ Is the lens stained with dirt? Clean your lens with a soft, clean cloth.
▶ Check the monitor and DVR settings.
▶ If the camera is exposed to very strong light, change the camera position.
The image on the screen is dark.
▶ Adjust the contrast feature of the monitor or DVR.
▶ If you have an intermediate device, set the 75Ω / Hi-z properly.
The camera is not working
properly, and the surface of the
camera is hot.
▶ Check that you have properly connected the camera to an
appropriate power source.
The DAY/NIGHT function does
not work.
▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
Color is not correct.
▶ Check the setting of WHITE BAL SETUP menu .
The screen flickers continually.
▶ Check that the camera is not pointing at the sun.
When coaxial communication is
not available
▶ Make sure that the camera and monitor are installed within
the recommended distance.
▶ Use the video amplifier equivalent to coaxitron if the
recommended installation distance is exceeded.
34_Troubleshooting
Specifications
‫މ‬
SPECIFICATIONS
sCD-3083N
sCD-3083p
VIDeO
1/3’’ Super HAD CCD II
Total pixels
1028(H) x 508(V)
1028(H) x 596(V)
effective pixels
976(H) x 494(V)
976(H) x 582(V)
scanning system
2 : 1 Interlace / Progressive
● SPECIFICATIONS
Imaging Device
synchronization
Internal / Line Lock
frequency
H:15.734KHz / V:59.94Hz
Horizontal Resolution
Color : ER mode Max 700TV lines(665 TVL ± 5%), B/W : 700TV lines
min. Illumination
H:15.625KHz / V:50Hz
COLOR : 0.1 Lux (50IRE, @F1.2), 0.0002Lux (SENS-UP, x512)
B/W : 0.01Lux (50IRE, @F1.2), 0.00002Lux (SENS-UP, x512)
s / N Ratio
52dB (AGC off, Weight on)
Video Output
CVBS : 1.0 Vp-p / 75Ω composite
lens Type
focal length(Zoom Ratio) 3 ~ 8.5mm (2.8x)
max. Aperture Ratio
F1.2
Angular field of View
H: 105.5°(Wide)~37.1°(Tele),V: 57.5°(Wide)~21.0°(Tele)
lens Type
DC Auto Iris
mount Type
Board Type
pan / Tilt /Rotate
pan/Tilt/Rotate Range
0°~352° / 0°~73° / 0°~348°
OpeRATIONAl
On screen Display
Camera Title
Multi-language Support by
Coaxial Cable
English, Japanese, Spanish, French,
Portuguese, Korean
Multi-language Support by
Coaxial Cable
English, French, German, Spanish,
Italian, Chinese, Russian, Polish,
Czech, Romanian, Serbian, Swedish,
Danish, Turkish, Portuguese
Off / On (Displayed 15 characters)
English_35
Specifications
SCD-3083N
Day & Night
SCD-3083P
Auto (ICR) / EXTERNAL/ Color / B/W
Backlight Compensation Off/ USER BLC / HLC / WDR
Wide Dynamic Range
128x
160x
Dynamic Range (SSDR) Off / On
Digital Noise Reduction (SSNR Ⅲ )
Off / On
Digital Image Stabilization Off / On
Privacy Masking
Off / On (12 Programmable zones, Polygonal type)
Sens-up
(Frame Integration)
2x ~ 512x
Gain Control
Off/ Low / High
White Balance
ATW / Outdoor / Indoor / Manual / AWC (1,700K° ~ 11,000K°)
Electronic Shutter Speed
1/60 ~ 1/120,000 sec
Digital Zoom
Off / On (1x ~ 16x)
1/50 ~ 1/120,000 sec
Flip / Mirror
Off / H-Rev / V-Rev / HV-Rev
Profile
Basic, Day & Night, Backlight, ITS, Indoor, User
VPS
Off / On
Communication
Coaxial Control ( SPC-300 Compatible )
Environmental
Operating Temperature / Humidity -10°C ~ +55°C (+14°F ~ +131°F) / Less than 90% RH
Electrical
Input Voltage
AC 24V ± 10% , DC 12V±10%
Power Consumption
0.35A
Mechanical
Dimension
Ø115.8 x 92.7mm
Weight
363g
※ This specification can be changed without notice for performance improvement of product.
36_ Specifications
DIMENSION
Unit: mm
● SPECIFICATIONS
Ø115.8
92.7
Ø97
English_37
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400
TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungcctvusa.com
www.samsungtechwin.com
www.samsungsecurity.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business Park
Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300, FAX : +44-1932-45-5325
P/NO. : PT01-002077A