Yamaha Disklavier Mark III Series User guide

Chapter 10
The Disklavier & MIDI
This chapter describes how the Disklavier can be used with other MIDI instruments. The Disklavier’s
MIDI functions are quite flexible, so there are many different connection possibilities. This chapter
provides a few examples. Even if your particular application is not among these, you should be able to
derive the information required to create your own setup by reading through these setup examples.
Note: For the MIDI setups described in this chapter, it is recommended that you connect your MIDI instrument to
the MIDI OUT connector and set the HOST SELECT switch to MIDI so that the Disklavier functions
properly. See “Setting the HOST SELECT Switch” on page 72.
Start/Stop Control of a
MIDI Instrument with
the Disklavier
In this setup, song disks are played on the
Disklavier and a MIDI drum machine or
sequencer plays in synchronization. When
[PLAY] is pressed, the MIDI instrument starts to
play. It can also be paused and stopped via the
Disklavier. In addition, the tempo of the MIDI
instrument will change as the tempo of the
Disklavier is adjusted.
1
Connect the Disklavier’s MIDI OUT
to the MIDI instrument’s MIDI IN
connector using a MIDI cable.
Disklavier
MIDI Drum Machine
or S
Sequencer
MIDI OUT
3
Press [FUNC.].
The FUNC. indicator lights and the
Function menu appears.
4
Press [>] until the c cursor is next
to the MIDI Setup option, then
press [ENTER].
The following display appears.
5
Press [>] until the c cursor is next
to the Remote option, then press
[ENTER].
MIDI IN
MIDI CABLE
The following display appears.
2
Set the MIDI instrument to
synchronize with the incoming
MIDI clock, sometimes called
“MIDI SYNC”.
Refer to its operating manual for details.
54
6
Press [+/YES] to set the Remote
Out parameter to ON.
7
Press [FUNC.] or [STOP] to exit the
MIDI setup.
It is also possible to set a split point on the
keyboard, so that, for example, your left-hand part
is backed by a bass guitar voice and your righthand part is backed by a marimba. MIDI data
from each side of the split point is sent to a
different MIDI channel, and the voice, volume,
and transposition for each side can be set
individually.
Note: This setup is not intended for Ensemble song
playback. It is intended for manual piano
playing with an external tone generator or
synthesizer. To send Ensemble song data to an
external MIDI instrument, see “Sending Song
Data to a MIDI Instrument” on page 60.
The following procedure describes how to play
MIDI instruments from the Disklavier using a
keyboard split point.
1
Connect the Disklavier’s MIDI OUT
to the external MIDI instrument’s
MIDI IN connector using a MIDI
cable.
Disklavier
MIDI Synthesizer or
Tone Generator
MIDI OUT
MIDI IN
MIDI CABLE
2
Press [FUNC.].
The FUNC. indicator lights and the
Function menu appears.
55
Chapter 10: The Disklavier & MIDI
In this setup, as you play the Disklavier, a
connected external MIDI tone generator or
synthesizer plays as well. This is sometimes
referred to as voice layering or unison. A typical
combination may be the Disklavier and a strings
voice, or the Disklavier and a vibes voice. From
the Disklavier, you can select the tone generator’s
voice, set its volume, and its transposition.
English
The Disklavier can now be used in the
sequencer system.
Sending the Keyboard
Data to a MIDI
Instrument
3
Press [>] until the c cursor is next
to the MIDI Setup option, then
press [ENTER].
7
The following display appears.
4
Press [>] until the c cursor is next
to the MIDI Out option, then
press [ENTER].
The following display appears.
The MIDI output can be transposed from
–60 to +60 in one semitone steps.
Separate transposition values can be set for
the left- and right-hand parts.
8
☛ See “Summary of the MIDI Out Parameter
in a MIDI Setup” on pages 68 and 69 for
details on the MIDI Out parameter.
5
If you want to transpose the MIDI
output, press [>] to position the
c cursor next to the Trans
parameter, then use the [–/NO]
and [+/YES] buttons to set a value.
Press [<] until the following
display appears.
If you did not set a split point, the
subsequent displays will be similar to the
following.
Press [>].
A display similar to the following appears.
9
6
To set a split point, press [>] until
the following display appears.
Then, with the c cursor next to
the Split parameter, use the
keyboard or the [–/NO] and
[+/YES] buttons to select a key.
Press [<] until the c cursor is next
to the Out Ch parameter, then use
the [–/NO] and [+/YES] buttons to
set a value.
The “Out Ch” option is used to select the
MIDI channel/s through which the
Disklavier will transmit MIDI data. It can
be set to OFF, MIDI channels 1 to 16 or HP.
Channel
OFF
1 to 16
HP
A keyboard split point can be set from A1
to C7.
56
Description
No data is sent to the MIDI
instrument.
The Disklavier keyboard data
and pedal data is sent on the
selected channel.
Keyboard data and on/off pedal
data will be sent on channel 1,
and continuous pedal data (half
pedal) will be sent on channel
3. In this case the pedal data
will be continuously variable
(half pedal).
10
To select a voice for the MIDI
output, press [>] until the
c cursor is next to the Prg
parameter, then use the [–/NO]
and [+/YES] buttons to select a
voice.
To set the volume of the MIDI
output, press [>] until the
c cursor is next to the Vol
parameter, then use the [–/NO]
and [+/YES] buttons to set the
volume.
1
Perform up to step 7 of “Sending
the Keyboard Data to a MIDI
Instrument”.
2
Press [>].
The following display appears.
3
If you had set a split point, you can set
different volume levels for the left- and
right-hand piano parts.
A setting of “###” will not change the
volume.
12
Use the [–/NO] and [+/YES]
buttons to to set the filtering
options.
Parameter Option
Key Touch ON
(default)
OFF
Press [FUNC.] or [STOP] to exit the
MIDI setup.
Pedal
4
Description
Sends silent notes,
diminishing sounds
Doesn’t send key
touch data
CONT
Sends continuous
(default) pedal data
SWITCH Sends On/Off
pedal data
Go back to step 8 in “Sending the
Keyboard Data to a MIDI
Instrument”.
57
Chapter 10: The Disklavier & MIDI
11
When sending data for the piano part you play on
the Disklavier keyboard to an external MIDI
instrument, the data contains keyboard touch data
and continuous pedal data as well. These data can
be filtered so that only basic MIDI messages are
output.
English
If you had set a split point, you can set
different voices for the left- and right-hand
parts.
A setting of “###” means no voice
selection.
Filtering KBD Out Data
Receiving Data from a
MIDI Sequencer
In this setup, the Disklavier is connected to a
MIDI sequencer for song recording and playback.
In this way you can use a MIDI sequencer’s
powerful recording and editing functions for
creating your Disklavier songs. The sequencer can
be a dedicated music sequencer, a MIDI data
recorder, or a MIDI sequencer program running
on a computer.
A 500 millisecond delay is applied to the
incoming MIDI data so that the Disklavier plays
more fluently. Because of the delay, be aware that
the beat indicator on the sequencer is slightly
ahead of the actual sounds being produced. Be
aware of this. To control the Disklavier in real
time, see “Controlling the Disklavier in Real
Time” on page 59.
The Disklavier’s Piano Rcv Ch parameter must be
set to match that of the sequencer track that
contains the piano parts. For example, if the piano
part is recorded on sequencer track 7 and track 7
is transmitting on MIDI channel 12, the
Disklavier should be set to receive on MIDI
channel 12. The Piano Rcv Ch parameter has the
following options.
Option
##
01 to 16
HP
1+2
Prg
Prg(all)
58
Description
MIDI IN data is played by just the
internal tone generator.
MIDI IN data is played by the piano
on the specified MIDI channel.
MDI IN data is played by the piano.
Left-hand part on MIDI channel 1,
right-hand part on MIDI channel 2,
and half pedal data on MIDI channel 3.
MIDI IN data is played by the piano.
Left-hand part on MIDI channel 1,
right-hand part on MIDI channel 2.
MIDI IN data is played by the piano
on the channel with the smallest
number containing a piano group
voice.
All channels that contain a piano
group voice in the MIDI IN data is
played by the piano.
1
Connect the MIDI sequencer’s
MIDI OUT to the Disklavier’s MIDI
IN with a MIDI cable.
MIDI Sequencer
Disklavier
MIDI IN
MIDI OUT
MIDI CABLE
2
Press [FUNC.].
The FUNC. indicator lights and the
Function menu appears.
3
Press [>] until the c cursor is next
to the MIDI Setup option, then
press [ENTER].
The following display appears.
4
With the c cursor next to the
Piano Part option, press [ENTER].
The following display appears.
5
Use the [–/NO] and [+/YES]
buttons to select a MIDI channel.
☛ See the list of available options on the left.
6
Press [>] until the c cursor is next
to the Delay In parameter, then
use the [–/NO] and [+/YES]
buttons to set the Delay In
(500 ms) to ON.
☛ For more information on the 500 ms delay
function, see “Controlling the Disklavier in
Real Time” on page 59.
7
Press either [FUNC.] or [STOP] to
return to the normal display.
The Disklavier can now be used in the
sequencer system.
Controlling the
Disklavier in Real Time
You need to set the Delay In parameter to OFF,
and set the Piano Rcv Ch parameter to match that
of the other keyboard’s MIDI transmit channels. If
the channels do not match, the Disklavier will not
respond to the MIDI data.
☛ Refer to the other keyboard’s user guide for
information on setting its transmit MIDI channels.
1
Connect the MIDI controller’s MIDI
OUT to the Disklavier’s MIDI IN
using a MIDI cable.
Disklavier
MIDI Synthesizer or
Tone Generator
MIDI IN
MIDI OUT
MIDI CABLE
2
Press [FUNC.].
The FUNC. indicator lights and the
Function menu appears.
59
Chapter 10: The Disklavier & MIDI
If you want to play the Disklavier in “real time”
via a MIDI master keyboard, synthesizer, or MIDI
guitar controller, this fixed delay can be turned
off. However, it will still take the Disklavier time
to respond to incoming MIDI data and the
Disklavier piano response time will vary based on
the velocity of the notes and is not usercontrollable.
English
As the Disklavier uses a mechanical system for
driving the piano keys, incoming MIDI data
cannot be played instantly. For this reason a fixed
delay of 500 ms is usually applied to all incoming
MIDI data. For most applications this delay will
not be a problem.
3
Press [>] until the c cursor is next
to the MIDI Setup option, then
press [ENTER].
The following display appears.
4
With the c cursor next to the
Piano Part option, press [ENTER].
The following display appears.
5
Use the [–/NO] and [+/YES]
buttons to select a MIDI channel.
☛ See page 58 for a list of available options.
6
Press [>] until the c cursor is next
to the Delay In parameter, then
use the [–/NO] and [+/YES]
buttons to set the Delay In (500
ms) to OFF.
Sending Song Data to a
MIDI Instrument
The parts of an Ensemble song are usually played
by the internal XG tone generator. However,
because the song data that is sent to the internal
XG tone generator is simultaneously sent to the
MIDI OUT connector, you can also output the
song file to an external tone generator or a MIDI
instrument such as a synthesizer.
When playing back songs from a computer, for
example, it is a good idea to connect an external
tone generator if the song has more than 16
channels. In this case, the Disklavier will play
channels 1 to 16 and the rest of the channels will
be played by the external tone generator. See
“Playing Back More than 16 Channels” on page
74.
For the best compatibility, your external MIDI
instrument should support Yamaha XG, General
MIDI (GM), or both.
1
Connect the Disklavier’s MIDI OUT
to the external MIDI instrument’s
MIDI IN connector using a MIDI
cable.
Disklavier
MIDI Synthesizer or
Tone Generator
MIDI OUT
7
MIDI IN
MIDI CABLE
Press [FUNC.] or [STOP] to return
to the normal display.
2
Press [FUNC.].
The FUNC. indicator lights and the
Function menu appears.
60
3
Press [>] until the c cursor is next
to the MIDI Setup option, then
press [ENTER].
The following display appears.
Use the [–/NO] and [+/YES]
buttons to select ESBL Out.
☛ See “Summary of the MIDI Out Parameter
in a MIDI Setup” on pages 68 and 69 for
details on the MIDI Out parameter.
6
1
Insert the song disk into the disk
drive.
2
Press [FUNC.].
The FUNC. indicator lights and the
Function menu appears.
3
Press [FUNC.] or [STOP] to exit the
MIDI Setup mode.
Press [>] until the c cursor is next
to the MIDI Setup option, then
press [ENTER].
The following display appears.
4
With the cursor next to the Piano
Part option, press [ENTER]. Then,
press [>] until the following
display appears.
5
Use the [–/NO] and [+/YES]
buttons to set the piano part
channels.
Option
##
01 to 16
Description
The import file is played by
the tone generator only.
The import file is played by
the piano on the specified
MIDI channel.
61
Chapter 10: The Disklavier & MIDI
5
Press [>] until the c cursor is next
to the MIDI Out option, then
press [ENTER].
Songs recorded onto floppy disks using MIDI
equipment other than the Disklavier can be played
back with the Disklavier. These are called “import
files”. For these files, you must specify the tracks
to be played by the Disklavier piano, because piano
parts in import files may be stored on any track.
English
4
Playing Back Import
Files
Prg
Prg(all)
6
The import file is played by the
piano on the channel with the
smallest number containing a
piano group voice.
All channels that contain a
piano group voice in the
import file is played by the
piano.
Press [PLAY] to play back the song
disk.
Synchronization Using
the MTC
MTC Synchronization
Settings
In order to achieve synchronization using the
MTC (MIDI time code), the settings for sending
and receiving the MTC are performed.
This Disklavier has a function that uses the MIDI
time code (MTC) to synchronize with an external
component.
This Disklavier can function either as the Master
or as the Slave when synchronization is to be
achieved using the MTC. Set the MTC-related
parameters in order to use the synchronization
function.
1
Press [FUNC.].
The FUNC. indicator lights and the
Function menu appears.
2
Press [>] until the c cursor is next
to the MIDI setup option, then
press [ENTER].
The following display appears.
3
Press [>] until the c cursor is next
to the MTC, then press [ENTER].
The following display appears.
62
Note: The MTC settings are stored in the
memory when the power is turned off.
To Operate Disklavier in the Slave
Mode
4a
4b
Use the [–/NO] and [+/YES]
buttons to select “MTC
Mode=Master”.
5b
Press [>] to position the c cursor
next to the “Rate”, and set the
frame rate.
Use the [–/NO] and [+/YES]
buttons to select “MTC
Mode=Slave”.
The MTC can be received at any of the
rates shown below. The rate is detected
automatically.
Rate parameter
24fps
25fps
DF
30fps
5a
To Operate Disklavier in the Master
Mode
Press [>] to position the c cursor
next to the “Thru”, and set the
output port.
Select the setting that corresponds to the
Frame Rate of the external component to be
synchronized with.
Rate parameter
24fps
25fps
DF
30fps (default)
6b
Press [>] to position the c cursor
next to “Out,” and set the
destination where the MTC is to
be sent.
The MTC can be output from either the
MIDI OUT connector or TO HOST
connector. Select the output destination
here.
Out parameter:
MIDI (default)
HOST
63
Chapter 10: The Disklavier & MIDI
☛ Depending on the MTC settings, some
restrictions apply to the remote function.
See “Correlation between MTC Settings
and Remote Function, and Behavior” on
page 67.
Set the connector from which the MTC
which has been received is to be output.
Thru parameter: OFF (default)
MIDI
HOST
“fps” stands for frames per second.
“DF” stands for dropped frame.
English
One of the following three MTC mode
parameters can be selected.
OFF:
The synchronization function is
(default)
set to OFF.
Slave: Disklavier operates in response to
the MTC received from the
external component.
Master: Disklavier sends the MTC to the
external component.
Using Disklavier as the MTC
Slave
2
Operate the external component.
(The external component must
first be set up to serve as the MTC
Master.)
3
Playback is performed in
synchronization with the MTC
received from the external
component.
In this status, Disklavier operates in
synchronization with the time information of the
external component.
Example of connections
Receiving the MTC from MIDI IN
Control Unit
SELECT
DRIVE
CONTROL UNIT DKC55RCD
GENERAL
INSTRUMENT
PLAY/PAUSE
STOP
REC
SONG SELECT/REV • FWD
PART
STANDBY
ON
L
ENTER
VOICE
R
FUNC.
METRONOME
VOLUME • • • –10 –8 –6 –4 –2 0
TEMPO
–/NO
+/YES
TRANSPOSE
BALANCE
External component
MIDI OUT equipped with MTC
or MTC OUT Master function
MIDI IN
(MD4S, AW2816, etc.)
MIDI CABLE
MTC Mode=Slave
Establish the MTC
Master mode by
following the
instructions in the
manual
accompanying the
external component.
Finely Adjusting the MTC
Synchronization Time
Playback can also be synchronized with an offset
applied to the received MTC. A deviation in the
synchronization can be adjusted using this
parameter.
During song selection, press [<] on the song
name display to display the previous screen.
The following display appears.
MTC Sync Playback (Slave Mode)
The MTC (MIDI time code) is received, and the
MIDI song is played back in synchronization with
the external component that supports the MTC.
“Slave” must have already been selected as the
MTC/MTC mode setting.
1
Select the song that supports
synchronization and that you
want to play using [SONG SELECT]
buttons. Press [PLAY/PAUSE]
button to engage the Playback
Standby mode.
The letters “MTC” flash on the counter area
of the playback screen, the following
display appears, and “MTC” flashes on the
display.
Flashes
64
Set the offset time.
Parameter - 500 ms to + 500 ms (in 10 ms
increments)
Note: In the case of E-SEQ format songs, songs that
do not support MTC synchronization, CD
playback or Smartkey playback, it is not
possible to perform MTC sync playback.
If pause, fast forward or reverse is performed
using the Disklavier panel or remote controller
during MTC sync playback, the MTC sync
playback is suspended. However, sync
playback can be resumed in response to
signals from the external component by
pressing the [STOP] button, and then pressing
the [START] button.
Start playing your song in
synchronization with the external
component.
5
Upon completion of the song,
stop the external component, and
then press [STOP].
MTC Offset appears only when a song that
supports synchronization has been selected.
The MTC Offset parameter is stored in the
memory even when the power is turned off.
Song recorded by MTC sync recording
are supported by MTC synchronization.
Note: By pressing the [PLAY/PAUSE] button again
in the playback standby mode in step 1, a song
that supports synchronization can also be
played back in the same way as a regular song.
Songs recorded by E-SEQ recording,
metronome recording or CD sync
recording are not supported by MTC
synchronization.
MTC Sync Recording (Slave Mode)
Sync recording is performed while the MTC is
received from the external component. “Slave”
must have already been selected as the MTC/
MTC mode setting.
1
Press [REC] to engage the Record
Standby mode.
The REC indicator lights and the
PLAY/PAUSE indicator flashes.
Using Disklavier as the MTC
Master
During playback and recording, Disklavier sends
the MTC, and the external component operates in
synchronization with the MTC.
Example of connections
Sending the MTC from MIDI OUT
Control Unit
2
Press [PLAY/PAUSE] and recording
will begin.
SELECT
DRIVE
CONTROL UNIT DKC55RCD
GENERAL
INSTRUMENT
PLAY/PAUSE
STOP
REC
SONG SELECT/REV • FWD
PART
STANDBY
ON
L
ENTER
VOICE
FUNC.
METRONOME
R
VOLUME • • • –10 –8 –6 –4 –2 0
TEMPO
–/NO
+/YES
TRANSPOSE
BALANCE
External component
equipped with MTC
MIDI OUT
MIDI IN Slave function
(MD4S, AW2816, etc.)
MIDI CABLE
The PLAY/PAUSE indicator stops flashing.
3
Operate the external component.
(The external component must
first be set up to serve as the MTC
Master.)
MTC Mode=Master
Rate = Adjust to the
external component’s
rate.
Out=MIDI
Establish the MTC
Slave mode by
following the
instructions in the
manual
accompanying the
external component.
Note: Bear in mind that regular recording will
be performed if you start playing the
song before the MTC message is output
from the external component. (You
must not step on the pedals.)
65
Chapter 10: The Disklavier & MIDI
Note: MTC sync recording is for recording
new songs only.
English
4
Sending the MTC from TO HOST
Control Unit
TO_HOST
SELECT
DRIVE
Computer
(Sequencer with MTC
COM port Slave function, etc.)
CONTROL UNIT DKC55RCD
GENERAL
INSTRUMENT
PLAY/PAUSE
STOP
REC
SONG SELECT/REV ¥ FWD
PART
STANDBY
ON
L
ENTER
VOICE
FUNC.
METRONOME
VOLUME ¥ ¥ ¥ —10 —8 —6 —4 —2
TEMPO
—/NO
+/YES
TRANSPOSE
BALANCE
0
R
MTC Mode=Master
Rate=Adjust to the
external component’s
rate.
Out=HOST
1
Establish the MTC
Slave mode by
following the
instructions in the
manual
accompanying the
soft.
Set the MTC-compatible external
component to the MTC receiving
standby mode.
Refer to its operating manual for details.
2
Proceed with playback or
recording using the control unit.
The MTC is sent, and the MTC-compatible
external component starts sync playback.
66
Correlation between MTC Settings and Remote Function, and
Behavior
Remote
MTC Mode
In
OFF
OFF
OFF
Receive
F2
F8
MTC
FA-FC
F2
MTC
×
×
×
×
×
Ο
Ο
ON
OFF
Ο
Ο
Ο
×
×
ON
ON
Ο
Ο
Ο
Ο
Ο
OFF
×
ON
Thru
Ο
ON
OFF
Ο
Ο
Thru
×
ON
ON
Ο
Ο
Thru
Ο
OFF
OFF
×
ON
Ο
Ο
ON
OFF
Ο
Ο
×
ON
ON
Ο
×
×
×
×
Ο
OFF
×
×
×
×
×
×
×
×
×
×
Thru
OFF
×
×
Ο
Ο
×
×
×
×
×
×
×
×
×
×
×
×
OFF
×
×
×
×
×
×
×
ON
×
×
OFF
Slave
Master
Chapter 10: The Disklavier & MIDI
FA-FC
English
Out
Transmit
Ο
Ο
Ο
Ο
×
×
×
×
When the song position has exceeded [7F 7F], F2 (Song Position), F8 (Continue) and F8 (Timing Clock)
are not sent.
67
Summary of the MIDI Out Parameter in a MIDI
Setup
The following tables show the differences among the MIDI OUT settings (KBD Out, ESBL Out, Thru
Port2) with the HOST SELECT switch set to MIDI.
MIDI OUT = KBD Out
Action
TO HOST
connector
Play on keyboard
Playback of ensemble
song file
MIDI data received from
TO HOST connector
Piano/Internal XG tone
generator
×
MIDI data sent if Out Ch
≠ OFF.
No internal tone generator
sounds unless Voice button
is ON and Local = ON.
×
×
No data sent except for
pedal data. (See note.)
Piano and internal tone
generator play normally.
×
MIDI data received from
MIDI IN connector
MIDI OUT connector
×
No MIDI data passed
through except for pedal
data. (See note.)
×
Piano and internal tone
generator play normally;
delay applied if Delay In =
ON.
× = TO HOST connector inactive
Note: When pedals are played (activated) by data, the depth of the pedals is read by the sensors and sent (KBD
Out) via channels selected in the Out Ch setting (as, unlike the keyboard, the pedals cannot distinguish
whether they are being activated by foot or by data).
MIDI OUT = ESBL Out
Action
TO HOST
connector
MIDI OUT connector
Piano/Internal XG tone
generator
×
No MIDI data sent unless
Voice button in ON.
Playback of ensemble
song file
×
All MIDI data sent except Piano and internal tone
generator play normally.
for piano parts (pedals
always sent on piano
channel); piano parts sent if
PianoPart ESBL OUT =
ON; if E-SEQ song,
incremental pedals not sent
on channel 3.
MIDI data received from
TO HOST connector
×
×
×
×
All MIDI data passed
through except piano parts;
piano parts sent if PianoPart
ESBL OUT = ON; delay
applied if Delay In = ON.
Piano and internal tone
generator play normally;
delay applied if Delay In =
ON.
Play on keyboard
MIDI data received from
MIDI IN connector
× = TO HOST connector inactive
68
No internal tone generator
sounds unless Voice button
is ON and Local = ON.
MIDI OUT = Thru Port2
Action
TO HOST
connector
Play on keyboard
MIDI data received from
TO HOST connector
×
No MIDI data sent.
No internal tone generator
sounds unless Voice button
is ON and Local = ON.
No MIDI data sent.
Piano and internal tone
generator play normally.
×
No MIDI data passed
through.
×
Piano and internal tone
generator play normally;
delay applied if Delay In =
ON.
× = TO HOST connector inactive
69
Chapter 10: The Disklavier & MIDI
MIDI data received from
MIDI IN connector
×
×
Piano/Internal XG tone
generator
English
Playback of ensemble
song file
×
MIDI OUT connector
Chapter 11
The Disklavier & Personal
Computers
Creating music with computers used to be a job for professionals only. However, in this age of
multimedia and personal computers, almost anyone can enjoy creating music.
General MIDI and Standard MIDI File (SMF) formats supported by the Disklavier are formats common
to most personal computers and MIDI instruments. For example, use your personal computer to download
SMF data from the Internet and play it on the Disklavier.
The Disklavier can be connected to a personal computer using the TO HOST connector. It can also be
connected via MIDI IN/OUT connectors, but a separate MIDI interface is required. The TO HOST
connector allows you to connect your Disklavier to a personal computer without the MIDI interface.
Personal Computer
le
l Cab
Seria
Disklavier
RS-232C
RS-422
TO HOST
MIDI OUT
MIDI
MIDI Drum Machine
or S
Sequencer
Cable
MIDI IN
Note: To use the Disklavier properly with the computer setups described in this chapter, it is recommended that
you connect your computer to the TO HOST connector and set the HOST SELECT switch to PC1, PC2, or
MAC depending on your computer type. See “Setting the HOST SELECT Switch” on page 72.
Connecting to a Personal Computer
Specifically, Apple Macintosh, IBM PC/AT, and NEC PC-9801/9821 series computers can be directly
connected to the Disklavier. Connect the RS-232C or RS-422 connector on your computer to the TO
HOST connector on the Control Unit using the specified cables shown below (available separately). Also
refer to your computer’s operating manual to make sure the connection is made properly.
Your computer may also require a serial port driver for this function. This software is used for controlling
the MIDI interface. For further information, please consult your Yamaha dealer.
Note: Be sure to turn the computer and Disklavier power switches off before making the connections and setting
the HOST SELECT switch.
70
Connecting to an Apple Macintosh Series Computer
Use a standard Macintosh 8-pin system peripheral cable.
Mini DIN 8-pin
2 (HSK 1)
1 (HSK 0)
5 (RxD-)
4 (GND)
3 (TxD-)
8 (RxD+)
7 (GP 1)
6 (TxD+)
Mini DIN 8-pin
English
1
2
3
4
5
6
7
8
Chapter 11: The Disklavier & Personal Computers
Connecting to an NEC PC-9801/9821 Series Computer
Use a standard 8-pin MINI DIN ➔ 25-pin D-SUB cross cable.
Mini DIN 8-pin
1
2
3
4
8
5
5 (CTS)
4 (RTS)
3 (RxD)
7 (GND)
D-SUB 25-pin
2 (TxD)
Male connector
Connecting to an IBM PC/AT Series Computer
(a) Use a standard 8-pin MINI DIN ➔ 9-pin D-SUB cross cable.
Mini DIN 8-pin
1
2
3
4
8
5
8 (CTS)
7 (RST)
2 (RxD)
5 (GND)
D-SUB 9-pin
3 (TxD)
Female connector
5 (CTS)
4 (RTS)
3 (RxD)
7 (GND)
D-SUB 25-pin
2 (TxD)
Female connector
(b) Use a standard 8-pin MINI DIN ➔ 25-pin D-SUB cross cable.
Mini DIN 8-pin
1
2
3
4
8
5
71
Setting the HOST SELECT Switch
Set the HOST SELECT switch on the rear panel of the Control Unit according to your computer type.
HOST SELECT
PC1
MIDI
PC2
MAC
HOST
SELECT
Baud
rate
Remarks
Apple Macintosh series
31,250
On the computer side, set the clock speed
to 1 MHz.
PC1
NEC PC-9801/9821 series
Some software require the HOST
31,250 SELECT switch to be set to PC2 (38,400
bps) in order to function properly.
PC2
IBM PC/AT series
38,400
General MIDI equipment
MIDI data is sent/received via MIDI
31,250 OUT/IN connectors, and not the TO
HOST connector.
MAC
MIDI
Computer type
* Apple and Macintosh are trademarks of Apple Computer, Inc.
* IBM PC/AT is a trademark of International Business Machines Corporation.
* PC-9801/9821 is a trademark of NEC Corporation.
Playing Back Songs
Created in a Computer
3
The following display appears.
Songs created and stored in your computer system
can be played back by the Disklavier.
1
Press [FUNC.].
The FUNC. indicator lights and the
Function menu appears.
2
Press [>] until the c cursor is next
to the MIDI Setup option, then
press [ENTER].
The following display appears.
72
With the c cursor next to the
Piano Part option, press [ENTER].
4
With the c cursor next to the
Piano Rcv Ch parameter, use the
[–/NO] and [+/YES] buttons to
select the channel for the piano
part.
The selected channel will be played by the
Disklavier piano, and the other channels by
the internal XG tone generator. See
“Receiving Data from a MIDI Sequencer”
on page 58 for details on MIDI channels.
5
Press [>] until the c cursor is next
to the Delay In parameter, then
use the [–/NO] and [+/YES]
buttons to set it.
You can record keyboard and pedal data onto a
computer.
Press [FUNC.].
2
Press [>] until the c cursor is next
to the MIDI Setup option, then
press [ENTER].
The following display appears.
3
Press [>] until the c cursor is next
to the MIDI Out option, then
press [ENTER].
The following display appears.
Press [FUNC.] or [STOP] to return
to the normal display.
☛ See “Summary of the MIDI Out Parameter
in a Computer Setup” on pages 76 and 77
for details on the MIDI Out parameter.
4
With the c cursor next to the MIDI
Out parameter, press [>].
The “Out Ch” option is used to select the
MIDI channel on which the Disklavier will
transmit MIDI data. It can be set to OFF,
MIDI channels 1 to 16, or HP.
73
Chapter 11: The Disklavier & Personal Computers
1
☛ For more information on the 500 ms delay
function, see “Controlling the Disklavier in
Real Time” on page 59.
6
English
Option Description
ON
A delay of 500 ms is applied to all
incoming MIDI data from the
computer so that the timing of the
piano and the internal XG tone
generator match for smooth
playback.
OFF
The delay is not applied, and the
piano is played in “real time”.
However, playback will not be
smooth. When Piano Rcv Ch is
set to ##, all channels are played
by the internal XG tone generator,
so Delay In is automatically set to
OFF.
Recording Songs to a
Computer (Sequencer)
Channel Description
OFF
No data is sent to the MIDI
instrument.
1 to 16 The Disklavier keyboard data and
pedal data is sent on the selected
channel.
HP
Keyboard data and on/off pedal
data will be sent on channel 1,
and continuous pedal data (half
pedal) will be sent on channel 3.
In this case the pedal data will be
continuously variable (half pedal).
If you want to play the piano parts on the
internal XG tone generator, set Piano Rcv
Ch to ##. There will be no delay effect if all
channels are monitored on the internal XG
tone generator.
☛ See “Controlling the Disklavier in Real
Time” on page 59 for details on the 500 ms
delay effect.
To monitor all recording parts on the
internal XG tone generator, set the “Echo
Back” or “Patch Thru” options on the
computer or sequencer to ON. See their
operating manuals for details.
5
Playing Back More than
16 Channels
You can play back from a computer song data that
contains up to 32 channels by connecting the
Disklavier’s TO HOST connector to the serial port
on a computer and its MIDI OUT connector to a
MIDI instrument. The 32 channels are sent to the
Disklavier using software corresponding to port
signals. The Disklavier plays channels 1 to 16
(port 1), and channels 17 to 32 (port 2) are output
to an external MIDI instrument.
1
Press [FUNC.].
2
Press [>] until the c cursor is next
to the MIDI Setup option, then
press [ENTER].
The following display appears.
3
Press [FUNC.] or [STOP] to return
to the normal display.
Press [>] until the c cursor is next
to the MIDI Out option, then
press [ENTER].
The following display appears.
☛ See “Summary of the MIDI Out Parameter
in a Computer Setup” on pages 76 and 77
for details on the MIDI Out parameter.
74
4
With the c cursor next to the MIDI
Out parameter, use the [–/NO]
and [+/YES] buttons to select
“Thru Port2”.
5
Press [FUNC.] or [STOP] to return
to the normal display.
Temporarily
Deactivating the
Internal Tone
Generators
Note: The OFF setting remains in effect only
until the Disklavier is switched off. The
next time you switch on the Disklavier,
the “Local” setting is returned to ON
(default).
5
Chapter 11: The Disklavier & Personal Computers
1
Press [FUNC.] or [STOP] to return
to the normal display.
Press [FUNC.].
The FUNC. indicator lights and the
Function menu appears.
2
Press [>] until the c cursor is next
to the MIDI Setup option, then
press [ENTER].
The following display appears.
3
Press [>] until the c cursor is next
to the Local option, then press
[ENTER].
4
Use the [–/NO] and [+/YES]
buttons to set Local to OFF.
English
When you are using the Disklavier’s internal XG
tone generator from a computer and do not want
any interference from the keyboard, you can set
the Disklavier so that the tone generator and
keyboard are temporarily disconnected. Even
when the Voice function is on, no sound is
produced from the piano. It will sound only by
messages received through the MIDI IN or TO
HOST connectors.
The following display appears.
75
Summary of the MIDI Out Parameter in a
Computer Setup
The following tables show the differences among the MIDI OUT settings (KBD Out, ESBL Out, Thru
Port2) with the HOST SELECT switch set to PC1, PC2 or MAC.
MIDI OUT = KBD Out
Action
Play on keyboard
Playback of
ensemble song file
MIDI data received
from TO HOST
connector
MIDI data received
from MIDI IN
connector
TO HOST connector
MIDI OUT connector
Piano/Internal XG tone
generator
MIDI data sent if Out
Ch ≠ OFF.
MIDI data sent if Out
Ch ≠ OFF.
No internal tone
generator sounds unless
Voice button is ON and
Local = ON.
No MIDI data sent.
No MIDI data sent.
Piano and internal tone
generator play normally.
No MIDI data passed
No MIDI data passed
Piano and internal tone
through except for pedal through except for pedal generator play normally;
data. (See note.)
data. (See note.)
delay applied if Delay In
= ON.
No MIDI data passed
through without delay.
No MIDI data passed
through.
Piano and internal tone
generator do not
respond.
Note: When pedals are played (activated) by data, the depth of the pedals is read by the sensors and sent (KBD
Out) via channels selected in the Out Ch setting (as, unlike the keyboard, the pedals cannot distinguish
whether they are being activated by foot or by data).
MIDI OUT = ESBL Out
Action
Play on keyboard
TO HOST connector
MIDI data received
from MIDI IN
connector
Piano/Internal XG tone
generator
MIDI data sent if Out
Ch ≠ OFF.
MIDI data sent unless
Voice button is ON.
No MIDI data sent
except for pedal data.
(See note.)
Piano and internal tone
All MIDI data sent
generator play normally.
except for piano parts
(pedal always sent on
piano channel); piano
parts sent if PianoPart
ESBL OUT = ON; if
E-SEQ song, incremental
pedals not sent on
channel 3.
Playback of
ensemble song file
MIDI data received
from TO HOST
connector
MIDI OUT connector
No internal tone
generator sounds unless
Voice button is ON and
Local = ON.
No MIDI data passed
All MIDI data passed
Piano and internal tone
through except for pedal through; delay applied if generator play normally;
data. (See note.)
Delay In = ON.
delay applied if Delay In
= ON.
All MIDI data passed
through without delay.
No MIDI data passed
through.
Piano and internal tone
generator do not
respond.
Note: When pedals are played (activated) by data, the depth of the pedals is read by the sensors and sent (KBD
Out) via channels selected in the Out Ch setting (as, unlike the keyboard, the pedals cannot distinguish
whether they are being activated by foot or by data).
76
MIDI OUT = Thru Port2
Action
Play on keyboard
MIDI data received
from MIDI IN
connector
Piano/Internal XG tone
generator
MIDI data sent if Out
Ch ≠ OFF.
No MIDI data sent.
No internal tone
generator sounds unless
Voice button is ON and
Local = ON.
No MIDI data sent
except for pedal data.
(See note.)
No MIDI data sent.
Piano and internal tone
generator play normally.
No MIDI data passed
All MIDI data on
through except for pedal channels 17-32 sent;
data. (See note.)
delay applied if Delay In
= ON.
Piano and internal tone
generator play channels
1-16 normally; delay
applied if Delay In =
ON.
All MIDI data passed
through.
Piano and internal tone
generator do not
respond.
No MIDI data passed
through.
Note: When pedals are played (activated) by data, the depth of the pedals is read by the sensors and sent (KBD
Out) via channels selected in the Out Ch setting (as, unlike the keyboard, the pedals cannot distinguish
whether they are being activated by foot or by data).
77
Chapter 11: The Disklavier & Personal Computers
MIDI data received
from TO HOST
connector
MIDI OUT connector
English
Playback of
ensemble song file
TO HOST connector
Chapter 12
Resetting Your Disklavier
If you want to return your Disklavier to its initial factory settings, follow the Reset function below.
Resetting Your
Disklavier
4
You can reset all settings, the Memory Disks, or
both.
1
Option
Setup
Memory
Disk [X] +
Setup
Description
All settings (See next page.)
Memory disk number [X] and
all settings (SMF format;
sample song included) (See
also next pag e.)
Memory
Memory disk number [X]
Disk [X]
only (SMF format; sample
song included)
Factory init. All Memory Disks are retsetting
urned to initial factory settings
Specify a disk.
When you select a Memory Disk, the reset
function will be effective for the selected
disk only.
If you select Memory Disk 0, the disk is
reset in SMF format, and an “opening”
song or songs are automatically re-recorded
on the disk. If you select Memory Disk 1
to F, the disks are reset in SMF format, and
nothing is recorded on the disk.
2
Use the [–/NO] and [+/YES]
buttons to select the item that
you want to reset. Then press
[ENTER].
The table on the next page lists the default
settings for the items that can be reset.
5a
If you selected Setup, Memory
Disk [X] + Setup or Memory Disk
[X], press [+/YES] when a display
similar to the following appears.
5b
If you selected Factory init.
setting, press [ENTER] when the
following display appears, then
press [+/YES].
Press [FUNC.].
The FUNC. indicator lights and the
Function menu appears.
3
Press [>] until the c cursor is next
to the Reset option, then press
[ENTER].
The following display appears.
➔
78
Forced Reset
2
When the message “UNFORMATTED
MEMORY DISK” appears, this indicates that all
Memory Disks are damaged.
1
In the Reset display, press [ENTER].
Note: If you accidentally turn off the Control Unit
while data is being stored to a Memory Disk,
one or all Memory Disks may be damaged.
They can only be recovered by returning them
to initial factory settings.
Note: Be sure to keep a backup of important data.
Parameter
General
Volume
Tempo
Transpose
Repeat
Pedal Cancel
Default
Options
0
0
0
OFF
PD o n
-10 to 0
-50 to +20
-24 to +24
ALL, RPT, RND, A-B
PDoff, PD on
001
0
100
OFF
001 to 128
0 to 101 (depending on basic voice)
000 to 127
OFF, ON
Metronome
Click
Tempo
Beat
Pedal Count
Vol
ON
117
4/4
OFF
100
OFF, ON
30 to 400
1/4 to 9/4
OFF, ON
50 to 127
M-Tune
TG Master Tune
00
-50 to 00 to +50
BALANCE
TG Master Balance
CD Master Balance
100
64
0 to 127, OFF
0 to 127, OFF
MIDI Setup
Piano Rcv Ch
Delay In (500 ms)
Import File L
Import File R
Piano Part ESBL Out
MIDI Out
Out Ch
Split
Trans L
Trans R
Remote Out
Remote In
Local
01
ON
Prg
Prg
OFF
KBD OUT
01
OFF
00
00
OFF
OFF
ON
##, 01 - 16, 1+2, Prg, Prg(all)
ON, OFF
##, 01 - 16, Prg, Prg(all)
##, 01 - 16, Prg
OFF, ON
ESBL Out, KBD Out, Thru Port2
01 to 16
OFF, A1 to C7
-60 to 00 to +60
-60 to 00 to +60
OFF, ON
OFF, ON
OFF, ON
Silent Functions
Reverb type
Keyboard movement
Polyphony
HALL1
ON
32
ROOM, HALL1, HALL2
ON, OFF
32, 64
Chapter 12: Resetting Your Disklavier
Note: You cannot back up write-protected songs
such as PianoSoft and PianoSoft.Plus songs
onto floppy disks.
Voice
Basic Voice
Variation Voice
Vol
Piano Tone
English
The following display appears.
Reset the Memory Disk as
described above.
79
Chapter 13
Troubleshooting
If you are having difficulty operating your Disklavier, see if any of the symptoms listed below apply to
your problem and follow the recommended remedy.
Power
You cannot turn on the Disklavier.
• Make sure the power cord is connected to a
suitable AC outlet.
• Switch on the Disklavier’s “MAINS” switch.
• Press the [STANDBY / ON] button and turn on
the Control Unit.
• If the Disklavier still cannot be turned on,
disconnect it from the AC wall outlet, and
consult your Disklavier dealer.
☛ See “Turning On the Disklavier” on page 14
in the Basic Operation Manual.
• Make sure that the remote control’s batteries
have been installed correctly.
☛ See “Installing Batteries in the Remote
Control” on page 2 in the Basic Operation
Manual.
• Check the condition of the remote control’s
batteries.
☛ See “Battery Replacement” on page 2 in the
Basic Operation Manual.
Playback
None of the playback functions can be
used.
Control Unit
• Insert a Disklavier song disk into the disk
drive.
The Control Unit does not appear to work
correctly.
Songs are played back at the wrong tempo
or in the wrong key.
• Turn off the Control Unit, wait 5 seconds, then
turn it back on.
If the problem continues, consult your
Disklavier dealer.
• Reset the tempo or transposition functions.
Once the tempo or transposition functions have
been set, they will affect playback of all songs
until another disk is inserted, or they are reset.
Remote Control
Songs are not played back in the normal
song order.
You cannot control the Disklavier using the
remote control.
• Make sure that you are pointing the remote
control at the Control Unit’s remote control
sensor.
• Make sure that you are within the remote
control’s specified operating range.
☛ See “Using the Remote Control” on page 2 in
the Basic Operation Manual.
80
• Check that the “RND” and “RPT” repeat
functions are off.
☛ See “All Song, Single Song, Random Repeat”
on page 36 in the Basic Operation Manual.
You selected a song using the remote
control’s number pad, but the last song on
the disk is selected.
• If a song number higher than the last song
number on the disk is specified, the last song
will be selected.
During playback, complex note trills and
faint pianissimo passages are occasionally
missed.
• Increase the Disklavier’s volume level.
The Disklavier lowers the playback volume by
reducing the force applied to each hammer. So
for notes that are already quiet (pianissimo,
etc.), when the playback volume is reduced
there may not be enough force applied to a
hammer for it to strike the strings.
Pedal
During playback, the pedals do not
operate.
• Check that the pedal cancel function is not set
to “PDoff.”
• The sustain pedal is not made to move. Only
the internal mechanism operates.
☛ See “Operating the Pedals Yourself” on page
41 in the Basic Operation Manual.
Tone Generator (Ensemble
Playback)
The metronome does not sound during
song playback.
• Check that the song uses a measures and beats
time format. If not, the metronome will not
sound.
When you play back a song you
downloaded from the internet, the volume
of the piano parts is too loud.
• Song data created for use with other electronic
instruments often include sound with high
velocity (loudness). Edit the volume of the
track containing high velocity.
During Ensemble song playback, the
Ensemble parts cannot be heard.
• Make sure that the amp’s volume control is set
to an appropriate level.
• Readjust the volume balance.
☛ See “Balancing the Ensemble Volume (TG
Master Balance)” on page 26 in the Basic
Operation Manual.
The pitch of the Disklavier and internal
XG tone generator do not match.
☛ See “Editing a Track’s Voice & Volume” on
page 42.
• Use the TG Master Tune function to tune the
internal XG tone generator.
PianoSmart
☛ See “Tuning the Tone Generator (TG Master
Tune)” on page 48 in the Basic Operation
Manual.
Pianosmart fails to work (fails to
synchronize).
• Check whether the CD is the same as the
number of the CD printed on the Smart
PianoSoft package, etc.
The TG Master Balance function does not
adjust the volume of the internal XG tone
generator.
• Make sure that the BALANCE parameter is set
to OFF.
81
Chapter 13: Troubleshooting
• If a time value higher than the total length of
the song is specified, the end of the song will
be selected.
English
A search time is specified using the remote
control, but the end of the song is selected.
• When the songs are all the same even if the
CD is different, copy Smart PianoSoft onto the
memory disk, and execute “Change to a
different CD.”
• When a copied CD and Smart PianoSoft are to
be played simultaneously, their playback
timing may not coincide.
☛ See “Balancing the Ensemble Volume (TG
Master Balance)” on page 26 in the Basic
Operation Manual.
Disk Utilities
You cannot copy a song in the Memory
Disk onto a floppy disk.
Recording
When recording the second part of an L/R
song, the first part will not play back for
monitoring.
• Set the Monitor Piano option to ON.
☛ See “Re-Recording One Part” on page 33.
When recording a new part to an existing
track, the new part replaces the existing
parts.
• Set the Record Tr option to OVERDUB.
☛ See “Overdubbing a Track” on page 39.
You cannot re-record.
• Re-recording is not possible on protected disks
such as PianoSoft and PianoSoft.Plus disks.
Connection with External
Devices
The Disklavier cannot send and receive
MIDI data with other MIDI instruments.
• Make sure the MIDI cables are connected
properly.
A MIDI loop was accidentally created
when you connected a computer to the
MIDI OUT connector on your Disklavier,
so that song data is sent back and forth
between the computer and and piano.
• Set MIDI Out to KBD Out.
☛ See Chapter 11 “The Disklavier & Personal
Computers”.
82
• Copy-protected songs in the Memory Disk
cannot be copied onto a floppy disk. They can
only be copied onto the Memory Disk.
• Make sure that the floppy disk’s erasure tab is
set to “unprotected.”
☛ See “Floppy Disk Accidental Erasure
Protection” on page 18.
Chapter 14
Display Error Messages
English
While operating your Disklavier an error message may appear in the display. If an error message appears,
refer to the table below for an explanation of the message.
Note: This table does not explain every error message.
The current function cannot be executed because
protected files exist on the floppy disk.
No more song data can be recorded onto the floppy disk
because the disk is full.
Use another floppy disk.
The current function cannot be performed because the
floppy disk’s erasure protection tab is set to “protected.”
Set the disk’s erasure protection tab to “unprotected.”
☛ See “Floppy Disk Accidental Erasure Protection” on
page 18.
No more song data can be recorded onto the disk because
the disk is nearly full.
No more than 60 songs can be recorded onto an E-SEQ
type disk.
No more than 99 songs can be recorded onto an SMF
type disk.
The current function cannot be performed because this
disk contains no songs or only one song.
A wrong floppy disk has been inserted as the destination
disk. Insert the correct floppy disk.
The floppy disk is either new and has not yet been
formatted for use with the Disklavier or uses a format not
recognized by the Disklavier.
Format the floppy disk.
☛ See “Formatting Disks” on page 17.
83
Chapter 14: Display Error Messages
PianoSoft songs are write-protected and cannot be
re-recorded.
In order to be copied, the destination disk must be the
same format as the floppy disk.
You must select the track you want to record before
recording.
Only E-SEQ files can be recorded onto an E-SEQ type
disk.
The disk may be damaged.
Press the Stop key to clear the message.
If this message appears frequently with other disks as
well, contact your nearest Yamaha service representative.
84
Chapter 15
Glossary
English
This glossary provides basic definitions of terms used frequently in Disklavier manuals.
E-SEQ Type Disk
An abbreviation for beats per minute.
Chain Play
One of two disk types that the Disklavier uses to
format disks. E-SEQ type disks are compatible
with earlier Disklavier models.
A Disklavier function for playing back multiple
disks sequentially.
Fast Forward & Reverse
Clavinova
TM
A series of Yamaha digital pianos.
Two Disklavier functions that allow you to
quickly locate a position within a song. This is
faster than preview and review, but the Disklavier
does not play.
Continuous Pedal
See “Incremental Pedal”.
Fast Preview & Review
Cursor
Two Disklavier functions that allow you to search
quickly through a song with the Disklavier
playing.
The “c” symbol that is used on the LCD to show
the currently selected function or option. When
entering song or disk titles, the cursor will be the
“_” symbol. Do not confuse this with the [<] and
[>] buttons.
Disk
Storage media for data. For clarity in the
Disklavier manuals, “disk” is used as a generic
term to refer to floppy disks, CDs and Memory
Disks.
Ensemble Song
A song which contains piano parts and
accompanying instrumental voices.
An Ensemble song contains the same left and
right-hand parts as an L/R song, and in addition,
up to 13 accompanying instrument tracks. These
extra tracks are played by the internal XG tone
generator. The accompanying tracks may be used
for acoustic bass, drums, strings, vibes, etc.
E-SEQ Song Format
A song file format developed by Yamaha for
saving songs.
Floppy Disk
The magnetic storage medium that the Disklavier
uses to save songs. The Disklavier uses the 3.5
inch 2DD and 2HD floppy disks commonly used
for computers.
Formatting
New floppy disks must be formatted before they
can be used with the Disklavier. Formatting
prepares the disk so that it is ready to store
Disklavier song data.
General MIDI (GM)
An addition to the MIDI standard that simplifies
the transfer of MIDI song files between
instruments of different manufacturers. A MIDI
song recorded using a GM compatible tone
generator should play back correctly when used
with any GM compatible tone generator. The
standard specifies that a GM compatible tone
generator must support 24-note polyphony, 16
parts, and 128 standard voices.
85
Chapter 15: Glossary
bpm
Half Pedal
Overdub
See “Incremental Pedal”.
The addition of tracks to an existing recording.
For example, a Disklavier rhythm track can be
created with overdubbing by recording a track
with a bass drum, then a track with a snare, then
hi-hat, etc.
Import File
Songs recorded onto floppy disks using MIDI
equipment other than the Disklavier and played
back by the Disklavier.
Piano Parts
Incremental Pedal
Piano pedals are not always completely up or
down and may be held somewhere in-between.
Using incremental pedal data (also called
continuous or half pedal data) the Disklavier
precisely records the up and down movement of
the piano pedals.
LCD
Liquid Crystal Display. The Control Unit has an
LCD that shows 2 large characters and 2 lines of
24 small characters. For clarity in the Disklavier
manuals, the LCD is referred to as the “display”.
Refers to the left- and right-hand piano parts of a
song. The left-hand piano part is recorded onto
track 1 and the right-hand piano part is recorded
onto track 2. These track assignments are the
default settings and can be changed.
PianoSoftTM
The PianoSoft Disk Collection is a library of
prerecorded song disks made by Yamaha
specifically for use with the Disklavier.
PianoSoft.PlusTM
PianoSoft.Plus disks contain Ensemble songs that
can be played on the Disklavier.
LED
Light Emitting Diode. The Control Unit’s front
panel indicators are LEDs.
Polyphony
The maximum number of voices (or sounds) that
can be produced at a time from MIDI instruments.
L/R Song
In a L/R song, the left-hand piano part is stored on
track 1 (L) and the right-hand piano part is stored
on track 2 (R). During playback you can cancel
either part, and then play that part yourself. When
recording an L/R song, you can record the two
parts simultaneously or separately.
Program Change Message
Memory Disk
Quantize
The Disklavier has 16 internal Memory Disks that
allow you to store song data without a floppy
disk. Each Memory Disk has a memory capacity
of 1MB.
A function for auto-correcting the timing of notes
you play on the piano. With the quantize function
on, the timing of notes played using the
Disklavier keyboard will automatically be
corrected to the specified quantize value.
MIDI messages used for selecting programs or
voices. When an Ensemble song starts playing,
Program Change messages are sent to the tone
generator to select the correct instrument voices
for each ensemble track.
Metronome
A built-in device designed to mark exact time by a
regularly repeated click and flashing LED. Used
for both recording and playback.
MIDI
An acronym for Musical Instrument Digital
Interface. MIDI allows electronic musical
instruments to communicate with each other.
86
Quiet Mode
A Silent system mode in which sound is output
through the speakers, enabling you to freely adjust
the volume of the piano.
Song
Short for “reverberation.” The effect that adds a
more realistic feel to a sound by simulating the
reflection of the sound in rooms and halls of
various sizes.
Normally, a short piece of music with lyrics.
However, for clarity in Disklavier manuals, the
term is used to refer to any piece of music of any
genre.
Rhythm Track
Song Format
Tracks of an ensemble song designated for the
accompanying rhythm. The rhythm track is
unaffected by the playback transposition function.
The method used to store song data in a file.
PianoSoft and PianoSoft.Plus songs use the ESEQ format. The Disklavier also supports songs
in the Standard MIDI File (SMF) format.
A Disklavier function that allows you to start
playback from a specific point within a song. This
function is set using the remote control.
Sequencer
A sequencer can be used with the Disklavier to
play back and record MIDI data.
Song Number
All songs on a Disklavier disk are numbered
sequentially. The currently selected song number
is shown in the LCD. Songs can be selected
directly by entering the song number using the
remote control’s number pad.
Song Sort
Silent Mode
A Silent system mode in which sound is output
through connected headphones so that you can
listen to songs or play the piano without
disturbing people around you.
Silent System
Yamaha’s innovative system in which a push of
the SILENT button keeps the hammers from
striking the strings, effectively silencing the
acoustic piano. Sound is sent to the digital piano
tone generator and output through the speakers
(Quiet mode) or headphones (Silent mode).
Smart PianoSoftTM
Software made by Yamaha containing MIDI signals
for playing back along with standara audio CDS.
SMF
Abbreviation for Standard MIDI File.
SMF Song Format
A song file format supported by MIDI sequencers
and music software.
SMF Type Disk
One of two disk types that the Disklavier uses to
format disks. SMF type disks automatically
record songs using SMF format 0.
A Disklavier function that allows you to rearrange
the order of songs on a disk.
Split Point
When a keyboard split point is set before
recording, notes played on the left-hand side of
the split point are saved as the left-hand part and
notes played on the right-hand side of the split
point are saved as the right-hand part. This allows
you to play the left- and right-hand parts
simultaneously, but on different tracks.
Standard MIDI File (SMF)
A file of MIDI data that can be read and used by a
number of different MIDI devices and computers.
The Disklavier supports all SMF playback
functions.
System Exclusive Messages
MIDI messages used for sending system data to a
connected MIDI device. For example, when
tuning the internal XG tone generator or an
external tone generator, System Exclusive
Messages are sent via MIDI.
TG Master Balance
A function that allows you to balance the volume
levels of the Disklavier and the internal XG tone
generator.
87
Chapter 15: Glossary
Search
English
Reverb
TG Master Tune
The function that allows you to tune the internal
XG tone generator, and if connected, an external
tone generator simultaneously so that their tunings
match that of the Disklavier.
Timer Play
A Disklavier function for automatically playing
back groups of disks at various pre-set times.
Tone Generator
An electronic device that can generate tones or
instrument voices.
Track
Disklavier ensemble song data is organized as
tracks. One song can be composed of up to 16
tracks.
Transpose
Changing the key of a song. For example, a song
in the key of C is transposed to the key of D when
it is moved up two semitones.
Velocity
Because the loudness of a piano note is
determined by the speed (velocity) with which a
string is struck by a hammer, note loudness is
referred to as velocity.
Voice
The sounds produced by a tone generator
expressing various instruments. See Chapter 15
“Internal XG Tone Generator Voice & Drum Kit
List” in the Basic Operation Manual for a listing
of basic voices, and the Appendix “MIDI Data
Format” at the very end of this manual for a full
listing of available voices.
XG
Yamaha XG is an extension of the GM (General
MIDI) format. Its greater polyphony, more voices,
and use of effects enhances the compatibility
between MIDI devices. When a song in the
Yamaha XG format is played on another XGcompatible tone generator or synthesizer, it plays
and sounds as the original composer/creator
intended.
88
Chapter 16
Specifications
Sensor System
Hammer Sensors
Pedal Sensors
Data Storage
Removable
Media
Control Unit
Keys
Pedals
Internal Memory
Single-beam, four-point, optical*
Sustain & shift: incremental, position-sensing, optical
Sostenuto (GP): on/off, optical
16-note polyphonic
Sustain & shift: incremental response
1.44 MB × 16 flash memory disks (16 MB (Maximum)); up to 9
groups and 99 program sets; built-in calendar/clock/timer
File Format
Standard MIDI File (format 0, 1) / E-SEQ
Floppy Disk
3.5" 2DD (720 KB) or 2HD (1.44 MB) floppy disk
Compact Disc
Yamaha PianoSoft.PlusAudio, audio CD
Main Display
Song number plus 24-character × 2-line LCD
Function Indicators
LEDs, including drive/disk number indicator
Drive
Switches
Dimensions (WHD)
Weight
Amplification
(GP)
Single-beam, optical, incremental (GP)
CD and floppy disk
Power, Host Select (MIDI, PC1, PC2, Mac)
227 × 87 × 180 mm (9" × 3 1/2" × 7")
2.2 kg (4.8 lbs)
60W × 2; tone and volume controls
Speakers
16 cm (6 1/4") woofer × 2, 2.5 cm (1") tweeter × 2
Outlet Box
(UP)
AC Outlet × 2, Main Switch, Output Jack × 2
Connectors
MIDI In/Out, AUX In/Out (R, L/Mono), Headphones × 2,
To Host (serial port), To Piano, CD Control,
Audio/Analog MIDI In, Foot Controller
Type
Polyphony
Ensemble Parts
Ensemble Tone Voice Module Modes
Normal Voices
Drum Voices
Pitch
Silent System
Advanced Wave Memory 2 (AWM2)
32-note max.
16
XG, GM
676 (480 selectable)
21 kits total (11 selectable)
Set at A=440, tunable ±50 cents in 1-cent steps
(in unison with digital piano tone)
Silencing Mechanism
Motor-driven hammer shank stopper
Action Compensation
Quick Escape mechanism (GP)
AWM2 digital stereo sampling (CFIIIS concert grand);
16 MB wave memory w/sustain pedal resonance effects
Piano Tone
Polyphony
SmartKey Capability
Power Source
Supplied Accessories
Optional Accessories
32-note stereo sampling/64-note stereo
Yes
Local AC current
Wireless remote control unit w/batteries, PianoSoft sample disk,
CD software, blank 3.5" 2HD floppy disk, owner's manuals,
control unit suspension bracket (GP),
HPE-170 headphones,
FC-4, FC-5 foot switches, FC-7 foot controller
89
Chapter 16: Specifications
Drive System
English
Key Sensors
Power Source
Local AC current
Supplied Accessories
Wireless remote control unit w/batteries, PianoSoft sample disk,
CD software, blank 3.5" 2HD floppy disk, owner's manuals,
control unit suspension bracket (GP), HPE-170 headphones
Optional Accessories
FC-4, FC-5 foot switches, FC-7 foot controller
Function & Controls
Playback
Functions
Playback
Controls
Recording
Functions
Silent System
Controls
Metronome
Editing
Functions
Utility
Functions
Media Select
Floppy disk, Memory Disks (1 to 16), CD
Song Select
Rev/fwd, song by song; numerical selection
Music Search
Rev/fwd, w/ or w/o sound; direct by time or measure
Repeat
Disk, song, random, segment A~B, segment A~
Programming
9 disk groups, 99 program sets, chain play, timer play
Others
L/R part select, auto start, space playback
Volume
11 levels (0 ~ -10)
Tempo
-50 ~ +20 in 1 % steps
Transposition
±24 semitones (2 octaves) in 1-semitone steps
Balance
Balancing volume of ensemble voices and piano
Others
Keyboard cancel, pedal cancel, pedal count-in
Tracks
16 (including 2 for piano)
L/R Dual Recording
Separate L/R or assignable split point
Quantize
1/4, 1/6, 1/8, 1/12, 1/16 of a quarter note
Others
Re-recording
Power
On/off (w/ pilot lamp)
Volume
Continuous
Reverb
3 modes, depth control
Range
30 ~ 400 beats per minute
Time Signatures
1/4, 2/4, 3/4, 4/4, 5/4, 6/4, 7/4, 8/4, 9/4
Function
Audible (tick, on/off, volume controllable in the Silent system),
visual (LEDs)
Track
Mix, move, copy, delete, transpose
Song
Copy, sort, delete, type convert (SMF, E-SEQ, earlier Disklavier),
time format convert
Disk
Format, copy, type convert
Calendar/Clock/Timer
Current time display, time/date stamp for recording
Title Entry
Disk: 64 characters max.
Song: 32 characters max.
* Some models do not have hammer sensors.
Specifications are subject to change without prior notice.
90
Appendix
Mark III Series
Full-Function Models
Appendix
MIDI Data Format
Appendix
MIDI Data Format
If you are familiar with MIDI, or are using a computer to control your music software with computergenerated MIDI messages, the data provided in this section can help you to control your Disklavier.
Messages include those that can be received by the piano part and/or those that can be received by an
ESBL part. Messages that can be transmitted as well as received are shown as “transmitted”.
1.
1.1
1.2.5
CHANNEL MESSAGES
Key On / Key Off
Cntrl#
7
(Piano Part, ESBL Part) (transmitted)
Piano Part reception note range = A-1~C7 : C3=60
ESBL part reception note range = C-2~G8
Velocity range = 1~127 (Only the Key On velocity is received)
1.2.1
1.2.7
Bank Select LSB
Data Range
0: Normal,
63: User voice,
64: SFX,
126: SFX kit,
127: Drum
0...127
You can select the Voice banks with MSB and LSB numbers.
MSB and LSB functions differently depending on the play
mode.
In XG mode, MSB numbers select Voice type (Normal Voice or
Drum Voice), and LSB number select Voice banks.
In TG300B mode, LSB is fixed, and MSB numbers select Voice
banks.
(See Normal Voice List Drum Voice List.)
A new bank selection will not become effective until the next
Program Change message is received.
Cntrl#
1
1.2.3
Parameter
Modulation
Data Range
0...127
Portamento Time
Parameter
Portamento Time
Data Range
0...127
When the parameter 1.2.9 Portamento = ON, values will adjust
the speed of pitch change.
A setting of 0 - minimum portamento time, and 127 - maximum
portamento time.
1.2.4
Cntrl#
11
1.2.8
Data Entry
Parameter
Expression
Hold1
Cntrl#
64
1.2.9
Parameter
Hold1
Cntrl#
6
38
Parameter
Data Entry MSB
Data Entry LSB
Data Range
0...127
0...127
Parameter value is determined by combining MSB and LSB.
Data Range
0...127
(0-63:off, 64-127:on)
Portamento
(ESBL Part)
Cntrl#
65
Parameter
Portamento
Data Range
0...127
(0-63:off, 64-127:on)
1.2.10 Sostenuto
(Piano Part, ESBL Part) (transmitted)
Parameter
Sostenuto
Data Range
0...127
(0-63:off, 64-127:on)
1.2.11 Soft Pedal
(Piano Part, ESBL Part) (transmitted)
Parameter
Soft Pedal
Data Range
0...127
(0-63:off, 64-127:on)
1.2.12 Harmonic Content
(ESBL Part)
Messages which adjust the resonance set for each Voice.
Cntrl#
71
Parameter
Harmonic Content
(ESBL Part)
Messages which set the value for the parameter specified by
RPN/NRPN.
Data Range
0...127
(Piano Part, ESBL Part) (transmitted)
Cntrl#
67
(ESBL Part)
Cntrl#
5
Expression
(Piano Part, ESBL Part)
Cntrl#
66
Modulation
(ESBL Part)
Data Range
0...127
Data Range
0...127
(0:-64, 64:+0, 127:+63)
Higher values will result in a more characteristic, resonant
sound.
Depending on the Voice, the effective range may be narrower
than the range available for adjustment.
1.2.13 Release Time
(ESBL Part)
Messages which adjust the envelope release time set for each
Voice.
1
MIDI Data Format
32
Parameter
Bank Select MSB
Parameter
Pan
Pan
Cntrl#
10
Bank Select
Cntrl#
0
Data Range
0...127
(ESBL Part)
Control Change
(ESBL Part) (transmitted)
1.2.2
1.2.6
Parameter
Main Volume
Appendix
1.2
Main Volume
(Piano Part, ESBL Part) (transmitted)
Cntrl#
72
Parameter
Release Time
Data Range
0...127
(0:-64, 64:+0, 127:+63)
$01
$63
$mm
$01
$64
$mm
$01
$66
$mm
$14
$rr
$mm
$15
$rr
$mm
$16
$rr
$mm
$17
$rr
$mm
$18
$rr
$mm
Messages which apply a portamento between the currentlysounding note and the subsequent note.
$19
$rr
$mm
Cntrl#
84
$1A
$rr
$mm
$1C
$rr
$mm
$1D
$rr
$mm
$1E
$rr
$mm
$1F
$rr
$mm
1.2.14 Attack Time
(ESBL Part)
Messages which adjust the envelope attack time set for each
Voice.
Cntrl#
73
Parameter
Attack Time
Data Range
0...127
(0:-64, 64:+0, 127:+63)
1.2.15 Brightness
(ESBL Part)
Messages which adjust the filter cutoff frequency set for each
Voice.
Cntrl#
74
Parameter
Brightness
Data Range
0...127
(0:-64, 64:+0, 127:+63)
1.2.16 Portamento Control
(ESBL Part)
Parameter
Portamento Control
Data Range
0...127
1.2.17 Effect1 Depth (Reverb Send Level)
(ESBL Part)
Cntrl#
91
Parameter
Effect1 Depth
Data Range
0...127
1.2.18 Effect3 Depth (Chorus Send Level)
(ESBL Part)
Cntrl#
93
Parameter
Effect3 Depth
Data Range
0...127
1.2.19 Effect4 Depth (Variation Effect Send Level)
(ESBL Part)
Cntrl#
94
Parameter
Effect4 Depth
Data Range
0...127
1.2.20 Data Increment / Decrement (for RPN)
(ESBL Part)
Cntrl#
96
97
Parameter
RPN Increment
RPN Decrement
Data Range
0...127
0...127
1.2.21 NRPN (Non-Registered Parameter Number)
(ESBL Part)
Cntrl#
98
99
Parameter
NRPN LSB
NRPN MSB
Data Range
0...127
0...127
First send the NRPN MSB and NRPN LSB to specify the
parameter which is to be controlled. Then use Data Entry to set
the value of the specified parameter.
* Note that once the NRPN has been set for a channel
subsequent data entry will be recognized as the same NRPN’s
value change. Therefore, after you use the NRPN, you should set
a Null (7FH, 7FH) value to avoid an unexpected result.
The following NRPN number can be received.
2
NRPN
Data entry
MSB LSB
MSB
$01
$08
$mm
$01
$09
$mm
$01
$0A
$mm
$01
$20
$mm
$01
$21
$mm
PARAMETER NAME and VALUE
RANGE
Vibrato Rate
mm : $00 - $40 - $7F (-64 - 0 - +63)
Vibrato Depth
mm : $00 - $40 - $7F (-64 - 0 - +63)
Vibrato Delay
mm : $00 - $40 - $7F (-64 - 0 - +63)
Filter Cutoff Frequency
mm : $00 - $40 - $7F (-64 - 0 - +63)
Filter Resonance
mm : $00 - $40 - $7F (-64 - 0 - +63)
EG Attack Time
mm : $00 - $40 - $7F (-64 - 0 - +63)
EG Decay Time
mm : $00 - $40 - $7F (-64 - 0 - +63)
EG Release Time
mm : $00 - $40 - $7F (-64 - 0 - +63)
Drum Filter Cutoff Frequency
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
Drum Filter Resonance
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
Drum EG Attack
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
Drum EG Decay Rate
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
Applies to both Decay1 and 2.
Drum Instrument Pitch Coarse
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
Drum Instrument Pitch Fine
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
Drum Instrument Level
mm : $00 - $7F (0 - max)
rr : drum instrument note number
Drum Instrument Pan
mm : $00 - $40 - $7F (random, left center - right)
rr : drum instrument note number
Drum Instrument Reverb Send Level
mm : $00 - $7F (0 -max)
rr : drum instrument note number
Drum Instrument Chorus Send Level
mm : $00 - $7F (0 - max)
rr : drum instrument note number
Drum Instrument Variation Send Level
mm : $00 - $7F (0 - max)
rr : drum instrument note number
MSB 14H- 1FH (for Drum) is valid only if the Multi Part
parameter PART MODE = DRUMS 1 or DRUMS2 for that
channel. (If PART MODE = DRUM, no values will be changed.)
1.2.22 RPN (Registered Parameter Number)
(ESBL Part)
Cntrl#
100
101
Parameter
RPN LSB
RPN MSB
Data Range
0...127
0...127
The following RPN numbers can be received.
RPN Data entry
MSB LSB MSB LSB PARAMETER NAME and VALUE
RANGE
00H 00H mmH — Pitch Bend Sensitivity
mm:00-18H (0-24 chromatic steps)
Assignable in chromatic steps up to
2 octaves
Default : 02H
LSB value is ignored.
00H 01H mmH 11H Fine Tuning
mm: 00H-40H-7FH (-64-0-+63)
00H 02H mmH — Coarse Tuning
mm: 28H - 40H - 58H (-24 - +24
chromatic steps)
LSB value is ignored.
7FH 7FH —
— RPN null
Cancels RPN and NRPN numbers
1.2.23 Channel Mode Messages
The following Channel Mode Messages can be received.
2nd byte
120
3rd byte
0
All Sound Off
121
123
124
125
126
127
0
0
0
0
0 ~ 16
0
Reset All Controllers
All Note Off
Omni Off
Omni On
Mono
Poly
1.4
Pitch Bend
(ESBL Part)
When Multi Part Parameter Rcv PITCH BEND CHANGE=OFF,
pitch bend for that part is not received.
1.5
Channel Aftertouch
1.6
Polyphonic Aftertouch
(ESBL Part)
1.2.23.1 All Sound Off
(Piano Part, ESBL Part) (transmitted)
(ESBL Part) (PianoPart) (transmitted)
Applying further pressure on the key does not output “key
aftertouch” information. Instead, key position is transmitted as
additional information.
ESBL part;
Terminates all sounds currently sounding on the specified
channel. However, the status of channel messages such as
Note On and Hold On is maintained.
Piano Part;
The status of channel messages is not maintained.
1.2.23.2 Reset All Controllers
2.
SYSTEM EXCLUSIVE MESSAGES
2.1
Parameter Change
The Disklavier receives the following parameter change
messages.
(ESBL Part)
The values of the following controllers will be reset to the
defaults.
RPN
1.2.23.3 All Note Off
(Piano Part, ESBL Part) (transmitted)
[UNIVERSAL NON REALTIME MESSAGE]
1) General MIDI Mode On
[XG NATIVE]
1) XG System on
2) XG System Data parameter change
3) Multi Effect1 Data parameter change
4) Multi Part Data parameter change
5) Drums Setup Data parameter change
[OTHER]
1) Master tuning
2) TG300 System Data Parameter change
3) TG300 Multi Effect Data parameter change
4) TG300 Multi Part Data parameter change
2.1.2
2.1.2.1
(Piano Part, ESBL Part)
Performs the same function as when an All Notes Off message is
received.
1.2.23.5 Omni On
(Piano Part, ESBL Part)
Performs the same function as when an All Notes Off message is
received.
1.2.23.6 Mono
(Piano Part, ESBL Part)
Performs the same function as when an All Sounds on message
is received, and if the 3rd byte (mono number) is in the range of
0 - 16, sets the corresponding channel to Mono Mode (Mode 4 :
m = 1).
(Piano Part, ESBL Part)
0;Off
Disklavier keyboard does not play the internal voices.
127;On
1.3
Program Change
(ESBL Part) (transmitted)
Messages for Voice selection.
With a combination of Bank Select, you can select not only basic
Voice numbers, but also variation Voice bank numbers.
F0
7F
7F
04
01
*SS
TT
F7
= Exclusive status
= Universal Real Time
= ID of target device
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
F0
7F
XN
04
01
SS
TT
F7
= Exclusive status
= Universal Real Time
= Device Number, xxx = don’t care
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
When received, the Volume MSB will be effective for the
System Parameter MASTER VOLUME.
* “SS” is the hexadecimal expression of Osssssss; same as for
“tt”, “aa”, etc.
1.2.23.7 Poly
(Piano Part, ESBL Part)
Master Volume
11110000
01111111
01111111
00000100
00000001
0sssssss
0ttttttt
11110111
or
11110000
01111111
0xxxnnnn
00000100
00000001
0sssssss
0ttttttt
11110111
1.2.23.4 Omni Off
1.2.24 Local Control
Universal Realtime Messages
(Piano Part, ESBL Part)
Terminates all notes currently on for the specified channel.
However, if Hold 1 or Sostenuto is on, notes will continue
sounding until these are turned off.
Performs the same function as when an All Sounds Off message
is received. and sets the corresponding channel to Poly Mode
(Mode 3).
MIDI Data Format
NRPN
VALUE
±O (center)
0 (off)
0 (off)
0 (off)
127 (max)
0 (off)
0 (off)
0 (off)
0 (off)
cancels the Portamento Source Key
Number that was received
number not specified; internal data
will not change
number not specified; internal data
will not change
Appendix
CONTROLLER
Pitch Bend Change
Channel Aftertouch
Polyphonic Aftertouch
Modulation
Expression
Hold l
Portamento
Sostenuto
Soft Pedal
Portamento Control
[UNIVERSAL REALTIME MESSAGE]
1) Master Volume
2.1.3
2.1.3.1
Universal Non-Realtime Messages
General MIDI Mode On
(ESBL Part)
11110000
01111110
01111111
00001001
00000001
11110111
or
11110000
01111110
0xxxnnnn
00001001
F0
7E
7F
09
01
F7
= Exclusive status
= Universal Non-Real Time
= ID of target device
= Sub-ID #1=General MIDI Message
= Sub-ID #2=General MIDI On
= End of Exclusive
F0
7E
XN
09
= Exclusive status
= Universal Non-Real Time
= Device Number, xxx = don’t care
= Sub-ID #1=General MIDI Message
3
00000001
11110111
01
F7
= Sub-ID #2=General MIDI On
= End of Exclusive
2.1.5
Other parameter changes
2.1.5.1
2.1.4
11110000
01000011
0001nnnn
00100111
00110000
00000000
00000000
0mmmmmmm
0lllllll
0ccccccc
11110111
XG Native Parameter Change
(ESBL Part)
With the Parameter Change messages as listed below, you can
change the characteristic of a Voice, such as by Effect Type or
effect parameter, transpose, tuning, and others.
11110000
01000011
0001nnnn
01001100
0aaaaaaa
0aaaaaaa
0aaaaaaa
0ddddddd
|
11110111
F0
43
1n
4C
aaaaaaa
aaaaaaa
aaaaaaa
ddddddd
|
F7
Exclusive status
YAMAHA ID
Device Number
XG Model ID
Address High
Address Mid
Address Low
Data
2.1.4.1
2.1.4.2
XG System Data parameter change
[XG NATIVE]
1) XG System Data
2) Multi Effect1 Data
3) Multi Part Data
4) Drums Setup Data
[QS300 NATIVE]
1) QS300 User Normal Voice Data
2.2.1
2.2.1.1
(ESBL Part)
See tables <1-1> and <1-5>.
If a Drum Setup Reset parameter change message is received,
the Drum Setup parameter values will be initialized.
Selecting a Drum Set will cause the Drum Setup parameter
values to be initialized.
4
Multi Effect1 Data bulk dump
See tables <1-1> and <1-3>.
2.2.1.3
Multi Part Data bulk dump
(ESBL Part)
See tables <1-1> and <1-4>.
2.2.1.4
Drums Setup Data bulk dump
(ESBL Part)
See tables <1-1> and <1-5>.
See tables <1-1> and <1-4>.
Drums Setup Data parameter change
XG System Data bulk dump
(ESBL Part)
(ESBL Part)
2.1.4.5
Checksum
End of Exclusive
See tables <1-1> and <1-2>.
2.2.1.2
See tables <1-1> and <1-3>.
Multi Part Data parameter change
Exclusive status
YAMAHA ID
Device Number
XG Model ID
ByteCount
ByteCount
Address High
Address Mid
Address Low
Data
(ESBL Part)
(ESBL Part)
2.1.4.4
F0
43
0n
4C
bbbbbbb
bbbbbbb
aaaaaaa
aaaaaaa
aaaaaaa
dd
|
|
ccccccc
F7
For the Address and Byte Count, refer to the supplementary
tables.
The Checksum is the value that results in a value of 0 for the
lower 7 bits when the Start Address, Byte Count, plus the
Checksum itself are added.
See tables <1-1> and <1-2>.
Multi Effect1 Data parameter change
XG Native Bulk Dump
11110000
01000011
0000nnnn
01001100
0bbbbbbb
0bbbbbbb
0aaaaaaa
0aaaaaaa
0aaaaaaa
0ddddddd
|
|
0ccccccc
11110111
(ESBL Part)
2.1.4.3
End of Exclusive
The Disklavier receives the following bulk dump data.
Exclusive status
YAMAHA ID
Device Number
XG Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
When this data is received. the Disklavier will switch to XG
mode and all the parameters will be initialized accordingly, and
XG-compatible messages such as NRPN and Bank Select
messages can be received.
Since approximately 50ms is required to execute this message,
be sure to leave an appropriate interval before the subsequent
message
Master Tune MSB
Master Tune LSB
(ESBL Part)
XG System On
F0
43
1N
4C
00
00
7E
00
F7
Exclusive status
YAMAHA ID
Device Number
Model ID
Sub ID2
Bulk Dump
(ESBL Part)
11110000
01000011
0001nnnn
01001100
0aaaaaaa
0aaaaaaa
0aaaaaaa
00000000
11110111
F0
43
1n
27
30
00
00
mm
ll
cc
F7
This message simultaneously changes the pitch of all channels.
2.2
End of Exclusive
* Any number is OK since the device number for the Disklavier
is fixed to “All”.
For parameters with data size of 2 or 4, transmit the appropriate
number of data bytes.
When sending the parameter change messages consecutively, be
sure to leave an appropriate interval (if the time base is 480. ca 5
unit) between the messages.
Master Tuning
(ESBL Part)
When General MIDI Mode On is received. the play mode will
be changed to XG mode.
When this happens, the ESBL part will receive the MIDI
messages which compatible with GM System Level 1, and
consequently will not receive NRPN and Bank Select messages.
Since approximately 50ms is required to execute this messag, be
sure to leave an appropriate interval before the subsequent
message.
2.2.2
QS300 Native Bulk Dump
11110000
01000011
0000nnnn
01001101
0bbbbbbb
0bbbbbbb
0aaaaaaa
0aaaaaaa
F0
43
0n
4B
bbbbbbb
bbbbbbb
aaaaaaa
aaaaaaa
Exclusive status
YAMAHA ID
Device Number
QS300 Model ID
ByteCount
ByteCount
Address High
Address Mid
0aaaaaaa
0ddddddd
|
|
0ccccccc
11110111
2.2.2.1
aaaaaaa
dd
|
|
ccccccc
F7
Address Low
Data
a)
Transmission
Transmitted.
b)
Reception
Once FE has been received. if no MIDI data is subsequently
received for longer than an interval of approximately
300msec. the Disklavier will perform the same function as
when ALL SOUNDS OFF. ALL NOTES OFF, and RESET
ALL CONTROLLERS messages are received, and will
then return to a status in which FE is not monitored.
Checksum
End of Exclusive
QS300 User Normal Voice Data bulk damp
(ESBL Part)
See tables <2-1> and <2-2>.
4.2
3.
SYSTEM COMMON MESSAGES
3.1
Song Position Pointer
a)
b)
3.2
Transmission
This message is transmitted only when the REMOTE OUT
parameter is set to On.
4.3
Reception
This message is received only when REMOTE IN
Parameter is set to On.
Timing Clock
a)
Transmission
This message is transmitted only when the REMOTE OUT
parameter is set to On.
b)
Reception
Not recognized.
Start
a)
Transmission
This message is transmitted only when the REMOTE OUT
parameter is set to On.
b)
Reception
This message is received only when REMOTE IN
Parameter is Set to On.
Song Select
Transmission
This message is transmitted only when the REMOTE OUT
parameter is set to On.
b)
Reception
This message is received only when REMOTE IN
Parameter is set to On.
4.
SYSTEM REALTIME MESSAGES
4.1
Active Sensing
4.4
Stop
a)
Transmission
This message is transmitted only when the REMOTE OUT
parameter is set to On.
b)
Reception
This message is received only when REMOTE IN
Parameter is Set to On.
MIDI Data Format
<Table 1-1>
Parameter Bass Address
Model ID = 4C [XG]
Parameter Change
Address
(H) (M) (L)
Description
XG SYSTEM 00
00
00
System
00
00
7D
Drum setup Reset
00
00
7E
XG System On
00
00
7F
All Parameter Reset
EFFECT1
02
01
00 Effect1 (Reverb, Chorus, Variation)
MULTI PART 08
00
00
Multi Part 1
:
08
0F
00
Multi Part 16
DRUM
30
18
00
Drum Setup 1
30
18
00
Drum Setup 2
------->
Address
0B
00
0C
00
:
3n
5B
00
3n
3n
Parameter
note number 13
note number 14
:
note number 91
n: Drum setup number (0, 1)
<Table 1-2>
MIDI Parameter Change table (SYSTEM) [XG]
Address
(H)
00
00
Size
00
04
05
06
7D
7E
7F
TOTAL SIZE
(H)
4
1
1
1
Data
Parameter
(H)
0000-07FF
MASTER TUNE
00 - 7F
00 - 7F
28 - 58
n
00
00
MASTER VOLUME
not used
TRANSPOSE
DRUM SETUP RESET
XG SYSTEM ON
ALL PARAMETER RESET
Appendix
a)
Description
Default value
(H)
-102.4 - +102.3 [cent]
1st bit3-0➝bit15-12
2nd bit3-0➝bit11-8
3rd bit3-0➝bit7-4
4th bit3-0➝bit3-0
0 - 127
-24 - +24 [semitones]
n=Drum setup number
00=XG system ON (receive only)
00=ON (receive only)
00 04 00 00
-400
7F
40
07
5
<Table 1-3>
MIDI Parameter Change table (EFFECT 1) [XG]
Address
(H)
02
01
00
02
03
04
05
06
07
08
09
0A
0B
0C
0D
TOTAL SIZE
02
01
10
11
12
13
14
15
TOTAL SIZE
02
01
20
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
TOTAL SIZE
02
01
30
31
32
33
34
35
TOTAL SIZE
02
01
40
6
Size
(H)
2
1
1
1
1
1
1
1
1
1
1
1
1
0E
1
1
1
1
1
1
6
2
1
1
1
1
1
1
1
1
1
1
1
1
1
0F
1
1
1
1
1
1
6
2
42
2
44
2
46
2
48
2
4A
2
4C
2
4E
2
50
2
52
2
54
2
56
57
58
59
1
1
1
1
Data
(H)
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
01-7F
Parameter
Description
REVERB TYPE MSB
REVERB TYPE LSB
REVERB PARAMETER 1
REVERB PARAMETER 2
REVERB PARAMETER 3
REVERB PARAMETER 4
REVERB PARAMETER 5
REVERB PARAMETER 6
REVERB PARAMETER 7
REVERB PARAMETER 8
REVERB PARAMETER 9
REVERB PARAMETER 10
REVERB RETURN
REVERB PAN
see Effect Type List
00 : basic type
see Effect Parameter List
’’
’’
’’
’’
’’
’’
’’
’’
’’
-∞dB...0dB...+6dB(0...64...127)
L63...C...R63(1...64...127)
Default value
(H)
01(=HALL1)
00
Depends on reverb type
’’
’’
’’
’’
’’
’’
’’
’’
’’
40
40
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
REVERB PARAMETER 11
REVERB PARAMETER 12
REVERB PARAMETER 13
REVERB PARAMETER 14
REVERB PARAMETER 15
REVERB PARAMETER 16
see Effect Parameter List
’’
’’
’’
’’
’’
Depends on reverb type
’’
’’
’’
’’
’’
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
01-7F
00-7F
CHORUS TYPE MSB
CHORUS TYPE LSB
CHORUS PARAMETER 1
CHORUS PARAMETER 2
CHORUS PARAMETER 3
CHORUS PARAMETER 4
CHORUS PARAMETER 5
CHORUS PARAMETER 6
CHORUS PARAMETER 7
CHORUS PARAMETER 8
CHORUS PARAMETER 9
CHORUS PARAMETER 10
CHORUS RETURN
CHORUS PAN
SEND CHORUS TO REVERB
see Effect Type List
00 : basic type
see Effect Parameter List
’’
’’
’’
’’
’’
’’
’’
’’
’’
-∞dB...0dB...+6dB(0...64...127)
L63...C...R63(1...64...127)
-∞dB...0dB... +6dB(0...64...127)
41 (=CHORUS1)
00
Depends on chorus Type
’’
’’
’’
’’
’’
’’
’’
’’
’’
40
40
00
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
CHORUS PARAMETER 11
CHORUS PARAMETER 12
CHORUS PARAMETER 13
CHORUS PARAMETER 14
CHORUS PARAMETER 15
CHORUS PARAMETER 16
see Effect Parameter List
’’
’’
’’
’’
’’
Depends on chorus Type
’’
’’
’’
’’
’’
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
01-7F
00-7F
00-7F
VARIATION TYPE MSB
VARIATION TYPE LSB
VARIATION PARAMETER 1 MSB
VARIATION PARAMETER 1 LSB
VARIATION PARAMETER 2 MSB
VARIATION PARAMETER 2 LSB
VARIATION PARAMETER 3 MSB
VARIATION PARAMETER 3 LSB
VARIATION PARAMETER 4 MSB
VARIATION PARAMETER 4 LSB
VARIATION PARAMETER 5 MSB
VARIATION PARAMETER 5 LSB
VARIATION PARAMETER 6 MSB
VARIATION PARAMETER 6 LSB
VARIATION PARAMETER 7 MSB
VARIATION PARAMETER 7 LSB
VARIATION PARAMETER 8 MSB
VARIATION PARAMETER 8 LSB
VARIATION PARAMETER 9 MSB
VARIATION PARAMETER 9 LSB
VARIATION PARAMETER 10 MSB
VARIATION PARAMETER 10 LSB
VARIATION RETURN
VARIATION PAN
SEND VARIATION TO REVERB
SEND VARIATION TO CHORUS
see Effect Type List
00 : basic type
see Effect Parameter List
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
-∞ dB...0dB...+6dB(0...64...127)
L63...C...R63(1...64...127)
-∞ dB...0dB...+6dB(0...64...127)
-∞ dB...0dB...+6dB(0...64...127)
05 (=DELAY L, C, R)
00
Depends on variation type
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
’’
40
40
00
00
TOTAL SIZE
02
01
5A
5B
1
1
00-01
VARIATION CONNECTION
00-0F,7F VARIATION PART
5C
5D
5E
5F
60
1
1
1
1
1
21
1
1
1
1
1
1
6
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
70
71
72
73
74
75
TOTAL SIZE
MW VARIATION CONTROL DEPTH
BEND VARIATION CONTROL DEPTH
CAT VARIATION CONTROL DEPTH
AC1 VARIATION CONTROL DEPTH
AC2 VARIATION CONTROL DEPTH
0:INSERTION, 1:SYSTEM
Part1...16(0...15)
0FF (127)
-64 - +63
-64 - +63
-64 - +63
-64 - +63
-64 - +63
00
7F
40
40
40
40
40
VARIATION PARAMETER 11
VARIATION PARAMETER 12
VARIATION PARAMETER 13
VARIATION PARAMETER 14
VARIATION PARAMETER 15
VARIATION PARAMETER 16
see Effect Parameter List
’’
’’
’’
’’
’’
Depends on variation type
’’
’’
’’
’’
’’
<Table 1-4>
MIDI Parameter Change table (MULTI PART) [XG]
Address
(H)
08
nn
nn
nn
nn
nn
nn
Data
(H)
00 - 20
00 - 7F
00 - 7F
00 - 7F
00 - 0F, 7F
00 - 01
nn
06
1
00 - 02
nn
07
1
00 - 03
nn
nn
nn
08
09
0A
1
2
28 - 58
00 - FF
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
0B
0C
0D
0E
0F
10
11
12
13
14
1
1
1
1
1
1
1
1
1
1
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
0 - 32
0 - 127
0 - 127
1 - 128
1 - 16,OFF
0:MONO
1:POLY
SAME NOTE NUMBER KEY ON ASSIGN 0:SINGLE
1:MULTI
2:INST (for DRUM)
PART MODE
0:NORMAL
1:DRUM
2-3:DRUMS1 - 2
NOTE SHIFT
-24 - +24 [semitones]
DETUNE
-12.8 - +12.7 [Hz]
1st bit3-0➝bit7-4
2nd bit3-0➝bit3-0
VOLUME
0 - 127
VELOCITY SENSE DEPTH
0 - 127
VELOCITY SENSE OFFSET
0 - 127
PAN
0/random, 1/L63-64/C-127/R63
NOTE LIMIT LOW
C-2 - G8
NOTE LIMIT HIGH
C-2 - G8
DRY LEVEL
0 - 127
CHORUS SEND
0 - 127
REVERB SEND
0 - 127
VARIATION SEND
0 - 127
nn
nn
nn
nn
nn
nn
nn
nn
15
16
17
18
19
1A
1B
1C
1
1
1
1
1
1
1
1
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
VIBRATO RATE
VIBRATO DEPTH
VIBRATO DELAY
FILTER CUTOFF FREQUENCY
FILTER RESONANCE
EG ATTACK TIME
EG DECAY TIME
EG RELEASE TIME
-64 - +63
-64 - +63
-64 - +63
-64 - +63
-64 - +63
-64 - +63
-64 - +63
-61 - +63
40
40 (drum part ignores)
40 (drum part ignores)
40
40
40
40
40
nn
nn
nn
nn
nn
nn
1D
1E
1F
20
21
22
1
1
1
1
1
1
28 - 58
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
MW PITCH CONTROL
MW FILTER CONTROL
MW AMPLITUDE CONTROL
MW LFO PMOD DEPTH
MW LFO FMOD DEPTH
MW LFO AMOD DEPTH
-24 -+24 [semitones]
-9600 - +9450 [cent]
-64 - +63
0 - 127
0 - 127
0 - 127
40
40
40
0A
00
00
1
1
1
1
1
1
29
1
1
1
28 - 58
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
BEND PITCH CONTROL
BEND FILTER CONTROL
BEND AMPLITUDE CONTROL
BEND LFO PMOD DEPTH
BEND LFO FMOD DEPTH
BEND LFO AMOD DEPTH
-24 - +24 [semitones]
-9600 - +9450 [cent]
-64 - +63
+100 - +100 [%]
+100 - +100 [%]
+100 - +100 [%]
42
40
40
40
40
40
00 - 01
00 - 01
00 - 01
Rcv PITCH BEND
Rcv CH AFTER TOUCH (CAT)
Rcv PROGRAM CHANGE
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
01
01
01
Description
ELEMENT RESERVE
BANK SELECT MSB
BANK SELECT LSB
PROGRAM NUMBER
Rcv CHANNEL
MONO/POLY MODE
Default value
(H)
part10=0, other =2
part10=7F, other=0
00
00
part no.
01
1 (all part)
part10=2, other=0
00 (other than Part10)
02 (Part10)
MIDI Data Format
nn
23
nn
24
nn
25
nn
26
nn
27
nn
28
TOTAL SIZE
nn
30
nn
31
nn
32
Parameter
Appendix
00
01
02
03
04
05
Size
(H)
1
1
1
1
1
1
40
08 00
(80)
64
40
40
40
00
7F
7F
00
40
00
7
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
33
34
35
36
37
38
39
3A
3B
3C
3D
3E
3F
1
1
1
1
1
1
1
1
1
1
1
1
1
00 - 01
00 - 01
00 - 01
00 - 01
00 - 01
00 - 01
00 - 01
00 - 01
00 - 01
00 - 01
00 - 01
00 - 01
00 - 01
Rcv CONTROL CHANGE
Rcv POLY AFTER TOUCH (PAT)
Rcv NOTE MESSAGE
Rcv RPN
Rcv NRPN
Rcv MODULATION
Rcv VOLUME
Rcv PAN
Rcv EXPRESSION
Rcv HOLD1
Rcv PORTAMENTO
Rcv SOSTENUTO
Rcv SOFT PEDAL
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
0/OFF, 1/ON
01
01
01
01
XG=01, GM=00
01
01
01
01
01
01
01
01
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
40
41
42
43
44
45
46
47
48
49
4A
4B
4C
1
1
1
1
1
1
1
1
1
1
1
1
1
00 - 01
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
Rcv BANK SELECT
SCALE TUNING C
SCALE TUNING C#
SCALE TUNING D
SCALE TUNING D#
SCALE TUNING E
SCALE TUNING F
SCALE TUNING F#
SCALE TUNING G
SCALE TUNING G#
SCALE TUNING A
SCALE TUNING A#
SCALE TUNING B
0/OFF,1/ON
-64 - +63 [cent]
-64 - +63 [cent]
-64 - +63 [cent]
-64 - +63 [cent]
-64 - +63 [cent]
-64 - +63 [cent]
-64 - +63 [cent]
-64 - +63 [cent]
-64 - +63 [cent]
-64 - +63 [cent]
-64 - +63 [cent]
-64 - +63 [cent]
XG=01, GM=00
40
40
40
40
40
40
40
40
40
40
40
40
nn
nn
nn
nn
nn
nn
4D
4E
4F
50
51
52
1
1
1
1
1
1
28 - 58
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
CAT PITCH CONTROL
CAT FILTER CONTROL
CAT AMPLITUDE CONTROL
CAT LFO PMOD DEPTH
CAT LFO FMOD DEPTH
CAT LFO AMOD DEPTH
-24 - +24 [semitones]
-9600 - +9450 [cent]
-64 - +63
0 - 127
0 - 127
0 - 127
40
40
40
00
00
00
nn
nn
nn
nn
nn
nn
53
54
55
56
57
58
1
1
1
1
1
1
28 - 58
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
PAT PITCH CONTROL
PAT FILTER CONTROL
PAT AMPLITUDE CONTROL
PAT LFO PMOD DEPTH
PAT LFO FMOD DEPTH
PAT LFO AMOD DEPTH
-24 - +24 [semitones]
-9600 - +9450 [cent]
-64 - +63
0 - 127
0 - 127
0 - 127
40
40
40
00
00
00
nn
nn
nn
nn
nn
nn
nn
59
5A
5B
5C
5D
5E
5F
1
1
1
1
1
1
1
00 - 5F
28 - 58
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
AC1 CONTROLLER NUMBER
AC1 PITCH CONTROL
AC1 FILTER CONTROL
AC1 AMPLITUDE CONTROL
AC1 LFO PMOD DEPTH
AC1 LFO FMOD DEPTH
AC1 LFO AMOD DEPTH
0 - 95
-24 - +24 [semitones]
-9600 - +9450 [cent]
-64 - +63
0 - 127
0 - 127
0 - 127
10
40
40
40
00
00
00
nn
nn
nn
nn
nn
nn
nn
60
61
62
63
64
65
66
1
1
1
1
1
1
1
00 - 5F
28 - 58
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
AC2 CONTROLLER NUMBER
AC2 PITCH CONTROL
AC2 FILTER CONTROL
AC2 AMPLITUDE CONTROL
AC2 LFO PMOD DEPTH
AC2 LFO FMOD DEPTH
AC2 LFO AMOD DEPTH
0 - 95
-24 - +24 [semitones]
-9600 - +9450 [cent]
-64 - +63
0 - 127
0 - 127
0 - 127
11
40
40
40
00
00
00
nn
nn
67
68
1
1
00 - 01
00 - 7F
PORTAMENTO SWITCH
PORTAMENTO TIME
0/OFF, 1/ON
0 - 127
00
00
1
1
1
1
1
1
3F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
01 - 7F
01 - 7F
PITCH EG INITIAL LEVEL
PITCH EG ATTACK TIME
PITCH EG RELEASE LEVEL
PITCH EG RELEASE TIME
VELOCITY LIMIT LOW
VELOCITY LIMIT HIGH
-64 -+63
-64 - +63
-64 - +63
-64 - +63
1 - 127
1 - 127
40
40
40
40
01
7F
nn
69
nn
6A
nn
6B
nn
6C
nn
6D
nn
6E
TOTAL SIZE
nn = Part Number (0:1Part, 1:2Part, 2:3Part, ..., 15:16Part)
For the DRUM PART, the following parameters have no effect.
•
•
•
•
•
8
SOFT PEDAL
BANK SELECT LSB
MONO/POLY
SCALE TUNING
PORTAMENTO
•
•
•
•
•
PITCH EG INITIAL LEVEL
PITCH EG ATTACK TIME
PITCH EG RELEASE LEVEL
PITCH EF RELEASE TIME
POLY AFTER TOUCH
<Table 1-5>
MIDI Parameter Change table (DRUM SETUP) [XG]
Address
(H)
3n
3n
3n
3n
3n
3n
3n
3n
rr
rr
rr
rr
rr
rr
rr
rr
00
01
02
03
04
05
06
07
3n
rr
08
3n
rr
09
3n
rr
0A
3n
rr
0B
3n
rr
0C
3n
rr
0D
3n
rr
0E
3n
rr
0F
TOTAL SIZE
Size
(H)
Data
(H)
Parameter
Description
Default
(H)
1
1
1
1
1
1
1
1
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
PITCH COARSE
PITCH FINE
LEVEL
ALTERNATE GROUP
PAN
REVERB SEND
CHORUS SEND
VARIATION SEND
-64 - +63
-64 - +63 [cent]
0 - 127
0/OFF, 1 - 127
0/random, 1/L63 - 64/C - 127/R63
0 - 127
0 - 127
0 - 127
40
40
Depends on the note
’’
’’
’’
’’
7F
1
1
1
1
1
1
1
1
10
00 - 01
00 - 01
00 - 01
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
KEY ASSIGN
Rcv NOTE OFF
Rcv NOTE ON
FILTER CUTOFF FREQUENCY
FILTER RESONANCE
EG ATTACK RATE
EG DECAY1 RATE
EG DECAY2 RATE
0/SINGLE, 1/MULTI
0/OFF, 1/ON
0/OFF, 1/ON
-64 - +63
-64 - +63
-64 - +63
-64 - +63
-64 - +63
00
Depends on the note
01
40
40
40
40
40
Appendix
[Note]
n: Drum number (0 - 1)
rr: note number (0D - 5B)
When XG system on or GM mode on messages are received, all Drum Setup parameters are initialized.
The Drum Setup Reset message can be used to initialized each Drum Setup parameter.
Selecting a Drum Set will cause the Drum Setup parameter values to be initialized.
<Table 2-1>
Parameter Bass Address
Model ID = 4B [QS300]
MIDI Data Format
Bulk Dump
Address
(H) (M) (L)
USER
11
00
00
NORMAL
VOICE
00
1F
00
Description
User Normal Voice 1
:
User Normal Voice 32
<Table 2-2>
MIDI Bulk Dump table (USER NORMAL VOICE) [QS300]
Address
(H)
Size
(H)
Data
(H)
Parameter
Description
Default
(H)
[Common]
11
nn
00
:
07
08
:
0A
0B
0C
17D 20-7E
01-03
00-7F
0D
:
3C
3D
3E
3F
40
41
42
43
44
45
46
47
48
49
4A
4B
Voice Name
not used
”
”
Element Switch
Voice Level
1:Element 1 on, 2:Element 2 on, 3:Element 1 and 2 on
not used
”
”
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-01
00-02
00-01
00-3F
00-7F
00-7F
00-3F
00-0F
00-1F
Wave Number High
Wave Number Low
Note Limit Low
Note Limit High
Velocity Limit Low
Velocity Limit High
Filter EG Velocity Curve
LFO Wave Select
LFO Phase Initialize
LFO Speed
LFO Delay
LFO Fade Time
LFO PMD Depth
LFO CMD Depth
LFO AMD Depth
[Element 1]
bit13-bit7
bit6-bit0
0:saw, 1:tri, 2:S&H
0:OFF, 1:ON
9
4C
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
6F
70
71
72
73
74
75
76
77
78
79
7A
7B
7C
7D
7E
7F
80
81
82
83
84
85
86
87
88
89
8A
8B
8C
20-60
0E -72
00-05
00-7F
00-03
39-47
39-47
39-47
00-7F
00-3F
00-3F
00-3F
00-3F
00-7F
00-7F
00-7F
00-7F
00-7F
00-3F
00-07
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
39-47
39-47
39-47
00-7F
00-3F
00-3F
00-3F
00-3F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-06
00-0F
39-47
00-7F
00-0F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
39-47
8D
:
DC
DD
:
12C
12D
:
17C
TOTAL SIZE
17D
nn=Voice Number (00-1F)
10
Note Shift
Detune
Pitch Scaling
Pitch Scaling Center Note
Pitch EG Depth
Velocity PEG Level Sensitivity
Velocity PEG Rate Sensitivity
PEG Rate Scaling
PEG Rate Scaling Center Note
PEG Rate 1
PEG Rate 2
PEG Rate 3
PEG Rate 4
PEG Level 0
PEG Level 1
PEG Level 2
PEG Level 3
PEG Level 4
Filter Resonance
Velocity Sensitivity
Cutoff Frequency
Cutoff Scaling Break Point 1
Cutoff Scaling Break Point 2
Cutoff Scaling Break Point 3
Cutoff Scaling Break Point 4
Cutoff Scaling Offset 1
Cutoff Scaling Offset 2
Cutoff Scaling Offset 3
Cutoff Scaling Offset 4
Velocity FEG Level Sensitivity
Velocity FEG Rate Sensitivity
FEG Rate Scaling
FEG Rate Scaling Center Note
FEG Rate 1
FEG Rate 2
FEG Rate 3
FEG Rate 4
FEG Level 0
FEG Level 1
FEG Level 2
FEG Level 3
FEG Level 4
Element Level
Level Scaling Break Point 1
Level Scaling Break Point 2
Level Scaling Break Point 3
Level Scaling Break Point 4
Level Scaling Offset 1
Level Scaling Offset 2
Level Scaling Offset 3
Level Scaling Offset 4
Velocity Curve
Pan
AEG Rate Scaling
AEG Scaling Center Note
AEG Key on Delay
AEG Attack Rate
AEG Decay 1 Rate
AEG Decay 2 Rate
AEG Release Rate
AEG Decay 1 Level
AEG Decay 2 Level
Address Offset High
Address Offset Low
Resonance Sensitivity
0:100%, 1:50%, 2:20%, 3:10%, 4:5%, 5:0%
0:1/2oct, 1:1oct, 2:2oct, 3:4oct
0 (Left)-14 (Right), 15:Scaling
bit13-bit7
bit6-bit0
[Element 2]
same as [Element 1]
”
”
[Element 3]
not used
”
”
[Element 4]
not used
”
”
XG Normal Voice List
Bank Select MSB = 000, LSB = Bank Number
Voice names in bold typeface are voices that can be selected in the Disklavier.
The Disklavier can produce all the voices listed below, but can only display bank 0 voices.
Instrument
Group
Piano
Instrument
Group
Organ
Guitar
Program Bank
Voice Name
#
#
17
0
DrawOrgn
32
DetDrwOr
33
60sDrOr1
34
60sDrOr2
35
70sDrOr1
36
DrawOrg2
37
60sDrOr3
38
EvenBar
40
16+2"2/3
64
Organ Ba
65
70sDrOr2
66
CheezOrg
67
DrawOrg3
18
0
PercOrgn
24
70sPcOr1
32
DetPrcOr
33
LiteOrg
37
PercOrg2
19
0
RockOrgn
64
RotaryOr
65
SloRotar
66
FstRotar
20
0
ChrchOrg
32
ChurOrg3
35
ChurOrg2
40
NotreDam
64
OrgFlute
65
TrmOrgFl
21
0
ReedOrgn
40
Puff Org
22
0
Acordion
32
AccordIt
23
0
Harmnica
32
Harmo 2
24
0
TangoAcd
64
TngoAcd2
25
0
NylonGtr
16
NylonGt2
25
NylonGt3
43
VelGtHrm
96
Ukulele
26
0
SteelGtr
16
SteelGt2
35
12StrGtr
40
Nyln&Stl
41
Stl&Body
96
Mandolin
27
0
Jazz Gtr
18
MelloGtr
32
JazzAmp
28
0
CleanGtr
32
ChorusGt
29
0
Mute.Gtr
40
FunkGtr1
41
MuteStlG
43
FunkGtr2
45
Jazz Man
30
0
Ovrdrive
43
Gt.Pinch
31
0
Dist.Gtr
40
FeedbkGt
41
FeedbGt2
32
0
GtrHarmo
65
GtFeedbk
66
GtrHrmo2
Bank 18 : Dark
Bank 19 : Dark
Bank 20 : Resonant
Bank 24 : Attack
Bank 24 : Release
Bank 27 : Reso Sweep
Bank 28 : Muted
Bank 32 : Detune 1
Bank 33 : Detune 2
Element
1
2
2
2
2
2
2
2
2
1
2
2
2
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
2
2
2
1
2
2
2
1
1
2
2
1
1
1
2
2
2
2
1
1
2
1
2
1
2
2
2
1
1
2
1
2
2
1
1
1
Instrument
Group
Bass
Strings
Bank 34 : Detune 3
Bank 35 : Octave 1
Bank 36 : Octave 2
Bank 37 : 5th 1
Bank 38 : 5th 2
Bank 39 : Bend
Bank 40 : Tutti
Bank 41 : Tutti
Bank 42 : Tutti
Program Bank
Voice Name
#
#
33
0
Aco.Bass
40
JazzRthm
45
VXUprght
34
0
FngrBass
18
FingrDrk
27
FlangeBa
40
Ba&DstEG
43
FngrSlap
45
FngBass2
65
ModAlem
35
0
PickBass
28
MutePkBa
36
0
Fretless
32
Fretles2
33
Fretles3
34
Fretles4
96
SynFretl
97
Smooth
37
0
SlapBas1
27
ResoSlap
32
PunchThm
38
0
SlapBas2
43
VeloSlap
39
0
SynBass1
18
SynBa1Dk
20
FastResB
24
AcidBass
35
Clv Bass
40
TeknoBa
64
Oscar
65
SqrBass
66
RubberBa
96
Hammer
40
0
SynBass2
6
MelloSB1
12
Seq Bass
18
ClkSynBa
19
SynBa2Dk
32
SmthBa 2
40
ModulrBa
41
DX Bass
64
X WireBa
41
0
Violin
8
SlowVln
42
0
Viola
43
0
Cello
44
0
Contrabs
45
0
Trem.Str
8
SlowTrStr
40
Susp Str
46
0
Pizz.Str
47
0
Harp
40
YangChin
48
0
Timpani
Element
1
2
2
1
2
2
2
2
2
2
1
1
1
2
2
2
2
2
1
1
2
1
2
1
1
1
1
2
2
2
1
2
2
2
1
2
2
1
2
2
2
2
1
1
1
1
1
1
1
2
1
1
2
1
Instrument
Group
Ensemble
Brass
Bank 43 : Velo-Switch
Bank 45 : Velo-Xfade
Bank 64 : Other wave
Bank 65 : Other wave
Bank 66 : Other wave
Bank 67 : Other wave
Bank 68 : Other wave
Bank 69 : Other wave
Bank 70 : Other wave
Program Bank Voice Name
#
#
49
0
Strings1
3
S.Strngs
8
SlowStr
24
ArcoStr
35
60sStrng
40
Orchestr
41
Orchstr2
42
TremOrch
45
VeloStr
50
0
Strings2
3
S.SlwStr
8
LegatoSt
40
Warm Str
41
Kingdom
64
70s Str
65
Str Ens3
51
0
Syn.Str1
27
ResoStr
64
Syn Str4
65
SS Str
52
0
Syn.Str2
53
0
ChoirAah
3
S.Choir
16
Ch.Aahs2
32
MelChoir
40
ChoirStr
54
0
VoiceOoh
55
0
SynVoice
40
SynVox2
41
Choral
64
AnaVoice
56
0
Orch.Hit
35
OrchHit2
64
Impact
57
0
Trumpet
16
Trumpet2
17
BriteTrp
32
WarmTrp
58
0
Trombone
18
Trmbone2
59
0
Tuba
16
Tuba 2
60
0
Mute.Trp
61
0
Fr.Horn
6
FrHrSolo
32
FrHorn2
37
HornOrch
62
0
BrasSect
35
Tp&TbSec
40
BrssSec2
41
HiBrass
42
MelloBrs
63
0
SynBras1
12
QuackBr
20
RezSynBr
24
PolyBrss
27
SynBras3
32
JumpBrss
45
AnaVelBr
64
AnaBrss1
64
0
SynBras2
18
Soft Brs
40
SynBras4
41
ChorBrss
45
VelBras2
64
AnaBras2
Element
1
2
1
2
2
2
2
2
2
1
2
2
2
2
1
1
2
2
2
2
2
1
2
2
2
2
1
1
2
2
1
2
2
2
1
1
2
2
1
2
1
1
1
2
2
1
2
1
2
2
2
2
2
2
2
2
2
2
2
2
1
2
2
2
2
2
Bank 71 : Other wave
Bank 72 : Other wave
Bank 96 : Other wave
Bank 97 : Other wave
Bank 98 : Other wave
Bank 99 : Other wave
Bank 100 : Other wave
Bank 101 : Other wave
11
MIDI Data Format
Bank 0 : (GM)
Bank 1 : Key Scale Planning
Bank 3 : Stereo
Bank 6 : Single
Bank 8 : Slow
Bank 12 : Fast Decay
Bank 14 : Double Attack
Bank 16 : Bright
Bank 17 : Bright
Element
1
1
1
2
2
1
1
2
2
2
2
2
2
2
2
1
2
2
2
2
1
2
1
2
2
2
2
2
2
2
1
1
2
2
2
1
2
1
2
1
1
2
2
1
1
2
1
1
2
2
2
1
1
2
2
1
2
2
2
Appendix
Chromatic
Percussion
Program Bank
Voice Name
#
#
1
0
GrandPno
1
GrndPnoK
18
MelloGrP
40
PianoStr
41
Dream
2
0
BritePno
1
BritPnoK
3
0
E.Grand
1
ElGrPnoK
32
Det.CP80
40
ElGrPno1
41
ElGrPno2
4
0
HnkyTonk
1
HnkyTnkK
5
0
E.Piano1
1
El.Pno1K
18
MelloEP1
32
Chor.EP1
40
HardEl.P
45
VX El.P1
64
60sEl.P
6
0
E.Piano2
1
El.Pno2K
32
Chor.EP2
33
DX Hard
34
DXLegend
40
DX Phase
41
DX+Analg
42
DXKotoEP
45
VX El.P2
7
0
Harpsi.
1
Harpsi.K
25
Harpsi.2
35
Harpsi.3
8
0
Clavi.
1
Clavi. K
27
ClaviWah
64
PulseClv
65
PierceCl
9
0
Celesta
10
0
Glocken
11
0
MusicBox
64
Orgel
12
0
Vibes
1
VibesK
45
HardVibe
13
0
Marimba
1
MarimbaK
64
SineMrmb
97
Balafon2
98
Log Drum
14
0
Xylophon
15
0
TubulBel
96
ChrchBel
97
Carillon
16
0
Dulcimer
35
Dulcimr2
96
Cimbalom
97
Santur
Bank Select
MSB = 064, LSB = 000
SFX Voice
Instrument
Group
Reed
Pipe
Synth Lead
Synth Pad
12
Program Bank Voice Name
#
#
65
0
SprnoSax
66
0
Alto Sax
40
Sax Sect
43
HyprAlto
67
0
TenorSax
40
BrthTnSx
41
SoftTenr
64
TnrSax 2
68
0
Bari.Sax
69
0
Oboe
70
0
Eng.Horn
71
0
Bassoon
72
0
Clarinet
73
0
Piccolo
74
0
Flute
75
0
Recorder
76
0
PanFlute
77
0
Bottle
78
0
Shakhchi
79
0
Whistle
80
0
Ocarina
81
0
SquareLd
6
Square 2
8
LMSquare
18
Hollow
19
Shmoog
64
Mellow
65
SoloSine
66
SineLead
82
0
Saw.Lead
6
Saw 2
8
ThickSaw
18
DynaSaw
19
DigiSaw
20
Big Lead
24
HeavySyn
25
WaspySyn
40
PulseSaw
41
Dr. Lead
45
VeloLead
96
Seq Ana
83
0
CaliopLd
65
Pure Pad
84
0
Chiff Ld
64
Rubby
85
0
CharanLd
64
DistLead
65
WireLead
86
0
Voice Ld
24
SynthAah
64
VoxLead
87
0
Fifth Ld
35
Big Five
88
0
Bass &Ld
16
Big&Low
64
Fat&Prky
65
SoftWurl
89
0
NewAgePd
64
Fantasy2
90
0
Warm Pad
16
ThickPad
17
Soft Pad
18
SinePad
64
Horn Pad
65
RotarStr
91
0
PolySyPd
64
PolyPd80
65
ClickPad
66
Ana Pad
67
SquarPad
Element
1
1
2
2
1
2
2
1
1
2
1
1
1
1
1
1
1
2
2
1
1
2
1
2
1
2
2
2
1
2
1
2
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Instrument
Group
Synth Pad
Synth
Effects
Program Bank Voice Name
#
#
92
0
ChoirPad
64
Heaven2
66
Itopia
67
CC Pad
93
0
BowedPad
64
Glacier
65
GlassPad
94
0
MetalPad
64
Tine Pad
65
Pan Pad
95
0
Halo Pad
96
0
SweepPad
20
Shwimmer
27
Converge
64
PolarPad
66
Celstial
97
0
Rain
45
ClaviPad
64
HrmoRain
65
AfrcnWnd
66
Caribean
98
0
SoundTrk
27
Prologue
64
Ancestrl
99
0
Crystal
12
SynDrCmp
14
Popcorn
18
TinyBell
35
RndGlock
40
GlockChi
41
ClearBel
42
ChorBell
64
SynMalet
65
SftCryst
66
LoudGlok
67
XmasBell
68
VibeBell
69
DigiBell
70
AirBells
71
BellHarp
72
Gamelmba
100
0
Atmosphr
18
WarmAtms
19
HollwRls
40
NylonEP
64
NylnHarp
65
Harp Vox
66
AtmosPad
67
Planet
101
0
Bright
64
FantaBel
96
Smokey
102
0
Goblins
64
GobSyn
65
50sSciFi
66
Ring Pad
67
Ritual
68
ToHeaven
70
Night
71
Glisten
96
BelChoir
103
0
Echoes
8
EchoPad2
14
Echo Pan
64
EchoBell
65
Big Pan
66
SynPiano
67
Creation
68
Stardust
69
Reso Pan
104
0
Sci-Fi
64
Starz
Element
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Instrument
Group
Ethnic
Percussive
Sound
Effects
Program Bank Voice Name
#
#
105
0
Sitar
32
DetSitar
35
Sitar 2
96
Tambra
97
Tamboura
106
0
Banjo
28
MuteBnjo
96
Rabab
97
Gopichnt
98
Oud
107
0
Shamisen
108
0
Koto
96
T. Koto
97
Kanoon
109
0
Kalimba
110
0
Bagpipe
111
0
Fiddle
112
0
Shanai
64
Shanai2
96
Pungi
97
Hichriki
113
0
TnklBell
96
Bonang
97
Gender
98
Gamelan
99
S.Gamlan
100 Rama Cym
101 AsianBel
114
0
Agogo
115
0
SteelDrm
97
GlasPerc
98
ThaiBell
116
0
WoodBlok
96
Castanet
117
0
TaikoDrm
96
Gr.Cassa
118
0
MelodTom
64
Mel Tom2
65
Real Tom
66
Rock Tom
119
0
Syn.Drum
64
Ana Tom
65
ElecPerc
120
0
RevCymbl
121
0
FretNoiz
122
0
BrthNoiz
123
0
Seashore
124
0
Tweet
125
0
Telphone
126
0
Helicptr
127
0
Applause
128
0
Gunshot
Element
1
2
2
2
2
1
1
2
2
2
1
1
2
2
1
2
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
2
1
2
2
1
1
2
1
2
2
2
2
1
1
1
1
Program
#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
MSB=064
LSB=000
Element
CuttngNz
CttngNz2
1
2
Str Slap
1
Fl.KClik
1
Rain
Thunder
Wind
Stream
Bubble
Feed
1
1
1
2
2
2
Dog
Horse
Bird 2
1
1
1
Ghost
Maou
2
2
Program
#
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
MSB=064
LSB=000
Element
Tel.Dial
DoorSqek
Door Slam
Scratch
Scratch 2
WindChm
Telphon2
1
1
1
1
2
1
1
CarEngin
Car Stop
Car Pass
CarCrash
Siren
Train
Jetplane
Starship
Burst
Coaster
SbMarine
1
1
1
1
2
1
2
2
2
2
2
Laughing
Scream
Punch
Heart
FootStep
1
1
1
1
1
MchinGun
LaserGun
Xplosion
FireWork
1
2
2
2
: No Sound
TG300B Normal Voice List
Bank Select MSB = Bank Number, LSB = ooo
Instrument
Group
Piano
Instrument
Group
Organ
Guitar
Program Bank
Voice Name
#
#
17
0
DrawOrgn
1
70sDrOr1
8
DetDrwOr
9
70sDrOr2
16
60sDrOr1
17
60sDrOr2
18
60sDrOr3
24
CheezOrg
32
DrawOrg2
33
EvenBar
40
Organ Ba
126 Slap-2
127 harpsi1
18
0
PercOrgn
1
70sPcOr1
8
DetPrcOr
32
PercOrg2
126 Slap-3
127 harpsi2
19
0
RockOrgn
8
RotaryOr
16
SloRotar
24
FstRotar
126 Slap-4
127 harpsi3
20
0
ChrchOrg
8
ChurOrg2
16
ChurOrg3
24
OrgFlute
32
TrmOrgFl
126 Slap-5
127 clavi1
21
0
ReedOrgn
126 Slap-6
127 clavi2
22
0
Acordion
8
AccordIt
126 Slap-7
127 clavi3
23
0
Harmnica
1
Harmo 2
126 Slap-8
127 celesta1
24
0
TangoAcd
126 Finger-1
127 celesta2
25
0
NylonGtr
8
Ukulele
16
NylonGt3
24
VelGtHrm
32
NylonGt2
40
LequintG
126 Finger-2
127 synbras1
26
0
SteelGtr
8
12StrGtr
9
Nyln&Stl
16
Mandolin
32
SteelGt2
126 Picked-1
127 synbras2
27
0
Jazz Gtr
1
MelloGtr
8
PdlSteel
126 Picked-2
127 synbras3
28
0
CleanGtr
8
ChorusGt
126 FretlsBs
127 synbras4
Element
1
2
2
2
2
2
2
2
2
2
1
2
1
1
2
2
2
2
2
2
2
2
2
2
1
2
2
2
2
2
2
1
1
2
1
2
2
2
1
1
2
2
1
2
1
1
1
1
2
2
1
1
2
2
1
2
2
2
1
1
2
1
1
1
2
2
1
2
1
2
Instrument
Group
Guitar
Bass
Program Bank Voice Name
#
#
29
0
Mute.Gtr
8
FunkGtr1
16
FunkGtr2
126 A-Bass
127 synbass1
30
0
Ovrdrive
126 Choir-1
127 synbass2
31
0
Dist.Gtr
8
FeedbkGt
9
FeedbGt2
126 Choir-2
127 synbass3
32
0
GtrHarmo
8
GtFeedbk
126 Choir-3
127 synbass4
33
0
Aco.Bass
126 Choir-4
127 newagepd
34
0
FngrBass
1
FngBass2
126 Strngs-1
127 synharmo
35
0
PickBass
8
MutePkBa
126 Strngs-2
127 choir pd
36
0
Fretless
1
Fretles2
2
Fretles3
3
Fretles4
4
SynFretl
5
Smooth
126 Strngs-3
127 bowed pd
37
0
SlapBas1
8
ResoSlap
126 Strngs-4
127 soundtrk
38
0
SlapBas2
126 E-Organ1
127 atmosphr
39
0
SynBass1
1
SynBa1Dk
8
AcidBass
9
FastResB
10
TeknoBa
16
ResoBass
126 E-Organ2
127 syn warm
40
0
SynBass2
1
ClkSynBa
2
ModulrBa
3
Seq Bass
8
DX Bass
9
X WireBa
16
RubberBa
17
SynBa2Dk
18
MelloSB1
19
SmthBa 2
126 E-Organ3
127 synfunny
Element
1
2
2
2
1
1
1
1
1
2
2
1
2
1
1
2
1
1
2
2
1
2
2
2
1
1
2
2
1
2
2
2
2
2
2
2
1
1
2
2
1
2
2
1
1
1
1
2
1
2
2
2
2
2
2
2
2
2
1
1
2
2
1
Instrument
Group
Strings
Ensemble
Program Bank Voice Name
#
#
41
0
Violin
8
SlowVln
126 E-Organ4
127 synecho1
42
0
Viola
126 E-Organ5
127 rain
43
0
Cello
126 E-Organ6
127 synoboe
44
0
Contrabs
126 E-Organ7
127 synecho2
45
0
Trem.Str
8
SlowTrStr
9
Susp Str
126 E-Organ8
127 synsolo
46
0
Pizz.Str
126 E-Organ9
127 synrdorg
47
0
Harp
126 SoftTP-1
127 synbell
48
0
Timpani
126 SoftTP-2
127 squareld
49
0
Strings1
1
Slow Str
8
Orchestr
9
Orchstr2
10
TremOrch
11
ChoirStr
16
S.Strngs
24
VeloStr
126 TP/TRB-1
127 strsect1
50
0
Strings2
1
70s Str
8
LegatoSt
9
Warm Str
10
S.SlwStr
126 TP/TRB-2
127 strsect2
51
0
Syn.Str1
1
Syn Str4
126 TP/TRB-3
127 strsect3
52
0
Syn.Str2
126 TP/TRB-4
127 pizz.str
53
0
ChoirAah
8
S.Choir
9
MelChoir
32
Ch.Aahs2
126 TP/TRB-5
127 violin 1
54
0
VoiceOoh
126 TP/TRB-6
127 violin 2
55
0
SynVoice
8
SynVox2
126 Sax-1
127 cello 1
56
0
Orch.Hit
1
OrchHit2
8
Impact
16
LoFiRave
126 Sax-2
127 cello 2
Element
1
1
2
2
1
2
2
1
2
2
1
2
2
1
1
2
2
2
1
2
2
1
1
1
1
1
2
1
1
2
2
2
2
2
2
1
2
1
1
2
2
2
1
2
2
2
1
2
2
1
1
1
2
2
2
2
2
1
2
1
1
2
1
1
2
2
2
2
1
1
13
MIDI Data Format
Element
1
1
1
2
1
1
1
2
1
2
2
2
2
2
1
2
2
2
1
2
2
2
1
2
2
1
1
1
2
2
2
2
1
1
1
1
2
1
2
1
1
2
1
2
2
1
2
2
1
2
2
2
1
1
1
2
1
2
1
1
1
2
2
2
2
1
2
2
1
2
2
1
2
1
2
2
2
2
Appendix
Chromatic
Percussion
Program Bank
Voice Name
#
#
1
0
GrandPno
8
GrndPnoK
16
MelloGrP
126 A-Piano1
127 a.piano1
2
0
BritePno
8
BritPnoK
126 A-Piano2
127 a.piano2
3
0
E.Grand
1
ElGrPno1
2
ElGrPno2
8
ElGrPnoK
126 A-Piano3
127 a.piano3
4
0
HnkyTonk
8
HnkyTnkK
126 A-Piano4
127 e.piano1
5
0
E.Piano1
8
Chor.EP1
16
VX El.P1
24
60sEl.P
25
HardEl.P
26
MelloEP1
32
El.Pno1K
126 A-Piano5
127 e.piano2
6
0
E.Piano2
8
Chor.EP2
16
VX El.P2
24
DX Hard
32
El.Pno2K
126 A-Piano6
127 e.piano3
7
0
Harpsi.
8
Harpsi.3
16
Harpsi.K
24
Harpsi.2
126 A-Piano7
127 e.piano4
8
0
Clavi.
8
Clavi. K
126 E-Piano1
127 hnkytnk
9
0
Celesta
126 E-Piano2
127 e.organ1
10
0
Glocken
126 E-Piano3
127 e.organ2
11
0
MusicBox
126 A-Guitr1
127 e.organ3
12
0
Vibes
1
HardVibe
8
VibesK
126 A-Guitr2
127 e.organ4
13
0
Marimba
8
MarimbaK
17
Balafon2
24
Log Drum
126 A-Guitr3
127 pipeorg1
14
0
Xylophon
126 E-Guitr1
127 pipeorg2
15
0
TubulBel
8
ChrchBel
9
Carillon
126 E-Guitr2
127 pipeorg3
16
0
Dulcimer
1
Dulcimr2
8
Cimbalom
126 Slap-1
127 acordion
Instrument
Group
Brass
Reed
Pipe
14
Program Bank Voice Name
#
#
57
0
Trumpet
1
Trumpet2
24
BriteTrp
25
WarmTrp
126 Sax-3
127 contrabs
58
0
Trombone
1
Trmbone2
126 Sax-4
127 harp 1
59
0
Tuba
1
Tuba 2
126 Brass-1
127 harp 2
60
0
Mute.Trp
126 Brass-2
127 guitar 1
61
0
Fr.Horn
1
FrHorn2
8
FrHrSolo
16
HornOrch
126 Brass-3
127 guitar 2
62
0
BrasSect
8
BrssSec2
126 Brass-4
127 elecgtr1
63
0
SynBras1
1
PolyBrss
8
SynBras3
9
QuackBr
16
AnaBrss1
126 Brass-5
127 elecgtr2
64
0
SynBras2
1
Soft Brs
8
SynBras4
16
AnaBrss2
17
VelBras2
126 Orch-Hit
127 sitar
65
0
SprnoSax
127 a.bass 1
66
0
Alto Sax
8
HyprAlto
127 a.bass 2
67
0
TnrSax 2
8
BrthTnSx
127 e.bass 1
68
0
Bari.Sax
127 e.bass 2
69
0
Oboe
127 slapbas1
70
0
Eng.Horn
127 slapbas2
71
0
Bassoon
127 fretles1
72
0
Clarinet
127 fretles2
73
0
Piccolo
127 flute1
74
0
Flute
127 flute2
75
0
Recorder
127 piccolo1
76
0
PanFlute
127 piccolo2
77
0
Bottle
127 recorder
78
0
Shakhchi
127 panpipes
79
0
Whistle
127 sax1
80
0
Ocarina
127 sax2
Element
1
1
2
2
1
1
1
2
2
1
1
1
1
1
1
1
1
2
2
1
2
2
1
1
2
2
2
2
2
2
2
2
2
2
1
2
2
2
2
1
1
1
1
1
2
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
2
2
1
2
1
1
Instrument
Group
Synth Lead
Synth Pad
Program Bank Voice Name
#
#
81
0
SquareLd
1
Square 2
2
Hollow
3
Mellow
4
SoloSine
5
Shmoog
6
LMSquare
8
SineLead
127 sax3
82
0
Saw.Lead
1
Saw 2
2
PulseSaw
3
ThickSaw
4
Big Lead
5
VeloLead
6
HeavySyn
7
DynaSaw
8
Dr. Lead
16
WaspySyn
127 sax4
83
0
CaliopLd
2
Pure Pad
127 clarint1
84
0
Chiff Ld
127 clarint2
85
0
CharanLd
8
DistLead
127 oboe
86
0
Voice Ld
127 eng.horn
87
0
Fifth Ld
1
Big Five
127 bassoon
88
0
Bass &Ld
1
Big&Low
2
Fat&Prky
127 harmnica
89
0
NewAgePd
1
Fantasy2
127 trumpet1
90
0
Warm Pad
1
ThickPad
2
Horn Pad
3
RotarStr
4
Soft Pad
127 trumpet2
91
0
PolySyPd
1
PolyPd80
127 trmbone1
92
0
ChoirPad
1
Heaven2
127 trmbone2
93
0
BowedPad
127 fr.horn1
94
0
MetalPad
1
Tine Pad
2
Pan Pad
127 fr.horn2
95
0
Halo Pad
127 tuba
96
0
SweepPad
1
PolarPad
8
Converge
9
Shwimmer
10
Celstial
127 brssect1
Element
2
1
1
2
2
2
2
1
1
2
1
2
2
2
2
2
1
2
2
1
2
2
1
2
1
2
2
1
2
1
2
2
1
2
2
2
1
2
2
1
2
2
2
2
2
1
2
2
2
2
2
2
2
1
2
2
2
2
2
2
2
2
2
2
2
1
Instrument
Group
Synth
Effects
Ethnic
Program Bank Voice Name
#
#
97
0
Rain
1
HrmoRain
2
AfrcnWnd
8
ClaviPad
127 brssect2
98
0
SoundTrk
1
Ancestrl
2
Prologue
127 vibe1
99
0
Crystal
1
SynMalet
2
SftCryst
3
RndGlock
4
LoudGlok
5
GlockChi
6
ClearBel
7
XmasBell
8
VibeBell
9
DigiBell
16
ChorBell
17
AirBells
18
BellHarp
19
Gamelmba
127 vibe2
100
0
Atmosphr
1
WarmAtms
2
NylnHarp
3
Harp Vox
4
HollwRls
5
NylonEP
6
AtmosPad
127 symallet
101
0
Bright
127 maletwin
102
0
Goblins
1
GobSyn
2
50sSciFi
127 glocken
103
0
Echoes
1
EchoBell
2
Echo Pan
3
EchoPad2
4
Big Pan
6
SynPiano
127 tubulbel
104
0
Sci-Fi
1
Starz
127 xylophon
105
0
Sitar
1
Sitar 2
2
DetSitar
8
Tambra
16
Tamboura
127 marimba
106
0
Banjo
1
MuteBnjo
8
Rabab
16
Gopichnt
24
Oud
127 koto
107
0
Shamisen
127 sho
108
0
Koto
8
T. Koto
16
Kanoon
127 shakhchi
109
0
Kalimba
127 whistle1
110
0
Bagpipe
127 whistle2
111
0
Fiddle
127 bottle
112
0
Shanai
1
Shanai2
8
Pungi
16
Hichriki
127 breath
Element
2
2
2
2
2
2
2
2
1
2
1
2
2
2
2
2
2
2
2
2
2
2
2
1
2
2
2
2
2
2
2
1
2
2
2
2
2
2
2
2
2
2
2
2
1
2
2
1
1
2
2
2
2
2
1
1
2
2
2
1
1
2
1
2
2
2
1
2
2
1
1
2
1
1
1
2
2
Instrument
Group
Percussive
Sound
Effects
Program Bank Voice Name
#
#
113
0
TnklBell
8
Bonang
9
Gender
10
Gamelan
11
S.Gamlan
16
Rama Cym
127 timpani
114
0
Agogo
127 melotom
115
0
SteelDrm
127 deepsnar
116
0
WoodBlok
8
Castanet
127 e.perc1
117
0
TaikoDrm
8
Gr.Cassa
127 e.perc2
118
0
MelodTom
1
Real Tom
8
Mel Tom2
9
Rock Tom
127 taiko
119
0
Syn.Drum
8
Ana Tom
9
ElecPerc
127 taikorim
120
0
RevCymbl
127 cymbal
121
0
FretNoiz
1
CuttngNz
2
Str Slap
3
CttngNz2
127 castanet
122
0
BrthNoiz
1
Fl.KClik
127 triangle
123
0
Seashore
1
Rain
2
Thunder
3
Wind
4
Stream
5
Bubble
127 orchehit
124
0
Tweet
1
Dog
2
Horse
3
Bird 2
127 telphone
125
0
Telphone
1
Tel.Dial
2
DoorSqek
3
DoorSlam
4
Scratch
5
WindChm
6
Scratch2
127 bird
126
0
Helicptr
1
CarEngin
2
Car Stop
3
Car Pass
4
CarCrash
5
Siren
6
Train
7
Jetplane
8
Starship
9
Burst
16
Coaster
127 jam
127
0
Applause
1
Laughing
2
Scream
3
Punch
4
Heart
5
FootStep
127 efctwatr
128
0
Gunshot
1
MchinGun
2
LaserGun
3
Xplosion
127 efctjngl
Element
2
2
2
2
2
2
1
2
1
2
1
1
1
1
1
1
1
2
2
1
2
1
1
1
2
1
1
2
2
1
1
2
1
2
1
1
2
1
1
1
2
2
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
2
2
2
2
1
1
1
1
1
1
1
2
1
1
2
2
2
XG Drum Voice List
Bank Select MSB = Bank Number, LSB = 000
Drum kit names in bold typeface are those that can be selected in the Disklavier.
Bank
127
Program #
Key
Alternate
127
127
127
127
127
127
127
127
126
126
1
2
9
17
25
26
33
41
49
1
2
Standard Kit
Standard2 Kit
Room Kit
Rock Kit
Electro Kit
Analog Kit
Jazz Kit
Brush Kit
Classic Kit
SFX 1
SFX 2
Reverse Cymbal
Reverse Cymbal
Note#
Note
13
C#
-1
3
Surdo Mute
14
D
-1
3
Surdo Open
15
D# -1
16
E
-1
17
F
-1
4
Scratch Push
18
F#
-1
4
Scratch Pull
19
G
-1
Finger Snap
20
G# -1
Click Noise
21
A
22
A# -1
23
B
24
C
0
Seq Click H
25
C#
0
Brush Tap
26
D
0
27
D# 0
28
E
0
O
Brush Swirl H
29
F
0
O
Snare Roll
30
F#
0
31
G
0
32
G# 0
33
A
34
A# 0
Open Rim Shot
Open Rim Shot 2
35
B
Bass Drum M
Bass Drum M 2
36
C
1
Bass Drum H
Bass Drum H 2
37
C#
1
Side Stick
38
D
1
Snare M
39
D# 1
Hand Clap
40
E
1
Snare H
41
F
1
Floor Tom L
42
F#
1
43
G
1
44
G# 1
45
A
46
A# 1
47
B
48
C
49
C#
50
D
2
High Tom
51
D# 2
Ride Cymbal 1
52
E
2
Chinese Cymbal
53
F
2
Ride Cymbal Cup
54
F#
2
Tambourine
55
G
2
Splash Cymbal
56
G# 2
Cowbell
57
A
Crash Cymbal 2
58
A# 2
59
B
60
C
3
Bongo H
Burst Noise
61
C#
3
Bongo L
Coaster
62
D
3
Conga H Mute
Analog Conga H
63
D# 3
Conga H Open
Analog Conga M
64
E
3
Conga L
Analog Conga L
65
F
3
Timbale H
66
F#
3
Timbale L
67
G
3
Agogo H
68
G# 3
Agogo L
69
A
70
A# 3
71
B
3
O
72
C
4
O
73
C#
4
74
D
4
75
D# 4
Claves
76
E
4
Wood Block H
77
F
4
Wood Block L
78
F#
4
Cuica Mute
Scratch Push
Scratch Push
79
G
4
Cuica Open
Scratch Pull
Scratch Pull
80
G# 4
2
Triangle Mute
81
A
2
Triangle Open
82
A# 4
Shaker
83
B
4
Jingle Bell
84
C
5
Bell Tree
Dog
Machine Gun
85
C#
5
Horse Gallop
Laser Gun
86
D
5
Bird 2
Explosion
87
D# 5
88
E
5
89
F
5
90
F#
5
91
G
5
off
assign
Hi Q
Whip Slap
-1
Metronome Click
Metronome Bell
-1
Seq Click L
O
Brush Swirl L
Brush Slap
Snare Roll 2
Castanet
Snare L
Snare L 2
Hi Q
Hi Q
SD Rock M
Snare M
SD Rock H
Bass Drum M
Bass Drum H 4
Bass Drum M
Bass Drum H 3
BD Rock
BD Analog L
BD Rock
BD Gate
0
Bass Drum L
0
Hi-Hat Closed
Hi-Hat Pedal
1
Hi-Hat Open
Snare M 2
SD Room L
SD Rock
SD Rock L
Analog Snare L
Snare H 2
SD Room H
SD Rock Rim
SD Rock H
Analog Snare H
Room Tom 1
Rock Tom 1
E Tom 1
Analog Tom 1
BD Soft
Gran Cassa Mute
Brush Slap M
Marching Sn M
Room Tom 2
Rock Tom 2
E Tom 2
Guitar Cutting Noise
Dial Tone
Guitar Cutting Noise 2
Door Creaking
Door Slam
String Slap
Analog Tom 2
Marching Sn H
Scratch 2
Brush Tom 1
Jazz Tom 1
Windchime
Jazz Tom 2
Brush Tom 2
Jazz Tom 2
Jazz Tom 3
Telephone Ring2
Analog HH Closed 2
Room Tom 3
Rock Tom 3
E Tom 3
Mid Tom L
Room Tom 4
Rock Tom 4
E Tom 4
2
Mid Tom H
Room Tom 5
Rock Tom 5
E Tom 5
2
Crash Cymbal 1
Analog Tom 3
Jazz Tom 3
Brush Tom 3
Analog Tom 4
Jazz Tom 4
Brush Tom 4
Analog Tom 5
Jazz Tom 5
Brush Tom 5
Analog HH Open
Room Tom 6
Rock Tom 6
E Tom 6
Analog Tom 6
Jazz Tom 4
Jazz Tom 5
Hand Cym.Open L
Jazz Tom 6
Brush Tom 6
Jazz Tom 6
Hand Cym.Closed L
FL.Key Click
Car Passing
Crash
Analog Cowbell
Siren
Hand Cym.Open H
Train
Jetplane
Hand Cym.Closed H
Cabasa
Maracas
O
Engine Start
Tire Screech
Ride Cymbal 2
3
MIDI Data Format
Analog Cymbal
Vibraslap
2
Scratch
Brush Tap H
Jazz Tom 1
Analog HH Closed 1
Low Tom
2
Gran Cassa
BD Jazz
Analog Side Stick
Floor Tom H
1
BD Analog H
Bass Drum L2
Appendix
1
1
1
4
Brush Slap L
Sticks
Analog Maracas
Starship
SbMarine
Rain
Laughing
Thunder
Screaming
Wind
Punch
Samba Whistle H
Stream
Heartbeat
Samba Whistle L
Bubble
Footsteps
Guiro Short
Feed
Guiro Long
Analog Claves
FireWork
Ghost
Maou
: Same as Standard kit
: No sound
15
TG300B Drum Voice List
Program #
Note# Note
Alternate
1
9
17
25
26
33
41
49
57
128
Standard Kit
Room Kit
Power Kit
Electro Kit
Analog Kit
Jazz Kit
Brush Kit
Orchestra Kit
SFX Set
C/M Kit
assign
25
C#
0
Snare Roll
26
D
0
Finger Snap
27
D#
0
Hi Q
Hi-Hat Closed
28
E
0
Whip Slap
Hi-Hat Pedal
29
F
0
7
Scratch Push
Hi-Hat Open
30
F#
0
7
Scratch Pull
Ride Cymbal 1
31
G
0
Sticks
32
G#
0
Click Noise
33
A
0
Metronome Click
34
A#
0
Metronome Bell
35
B
0
Bass Drum M
36
C
1
Bass Drum H
37
C#
1
Side Stick
38
D
1
Snare M
39
D#
1
Hand Clap
40
E
1
Snare H
41
F
1
Floor Tom L
42
F#
1
43
G
1
44
G#
1
45
A
1
1
BD Analog H
BD Jazz
BD Soft
SD Power
SD Electronic
Analog Snare L
SD Power
Room Tom 1
Room Tom 1
E Tom 1
Analog Tom 1
Jazz Tom 1
Brush Tap
Concert SD
Brush Slap
Castanet
High-Q
Brush Swirl
Concert SD
Slap
Jazz Tom 1
Timpani F
Scratch Push
Timpani F#
Scratch Pull
Analog HH Closed 1
Room Tom 2
Room Tom 2
E Tom 2
Analog Tom 2
Jazz Tom 2
Jazz Tom 2
Analog HH Closed 2
Room Tom 3
Room Tom 3
E Tom 3
Hi-Hat Open
Analog Tom 3
Jazz Tom 3
Jazz Tom 3
46
A#
1
47
B
1
Mid Tom L
Room Tom 4
Room Tom 4
E Tom 4
Analog Tom 4
Jazz Tom 4
Jazz Tom 4
Room Tom 5
Room Tom 5
E Tom 5
Analog Tom 5
Jazz Tom 5
Jazz Tom 5
48
C
2
Mid Tom H
49
C#
2
Crash Cymbal 1
50
D
2
High Tom
51
D#
2
Ride Cymbal 1
52
E
2
Chinese Cymbal
53
F
2
Ride Cymbal Cup
54
F#
2
Tambourine
55
G
2
Splash Cymbal
56
G#
2
Cowbell
57
A
2
Crash Cymbal 2
58
A#
2
Vibraslap
59
B
2
Ride Cymbal 2
60
C
3
Bongo H
Gran Cassa
Analog Side Stick
Hi-Hat Pedal
Low Tom
1
BD Electronic
Hi-Hat Closed
Floor Tom H
1
BD Jazz
BD Power
Analog HH Open
Analog Cymbal
Room Tom 6
Room Tom 6
E Tom 6
Analog Tom 6
Reverse Cymbal
Jazz Tom 6
Jazz Tom 6
Timpani G
Sticks
Timpani G#
Square Click
Timpani A
Metronome Click
Timpani A#
Metronome Bell
Timpani B
Guitar Fret Noise
Timpani C
Guitar Cutting Down
Timpani C#
Guitar Cutting Up
Timpani D
Ac Bass Slap
Timpani D#
FL.Key Click
Timpani E
Laughing
Timpani F
Screaming
SD Electro
Hi-Hat Open 1
Hi-Hat Open 2
Punch
Heartbeat
Analog Cowbell
Footsteps 1
Hand Cym.1
Footsteps 2
Applause
Hand Cym.2
Door Creaking
Door Slam
61
C#
3
Bongo L
62
D
3
Conga H Mute
Analog Conga H
Windchime
63
D#
3
Conga H Open
Analog Conga M
Scratch
Engine Start
64
E
3
Conga L
Analog Conga L
Tire Screech
65
F
3
Timbale H
Car Passing
66
F#
3
Timbale L
Crash
67
G
3
Agogo H
Siren
68
G#
3
Agogo L
Train
69
A
3
Cabasa
70
A#
3
Maracas
71
B
3
2
Samba Whistle H
Starship
72
C
4
2
Samba Whistle L
Gunshot
73
C#
4
3
Guiro Short
Machine Gun
74
D
4
3
Guiro Long
Laser Gun
Jetplane
Analog Maracas
Helicopter
Analog Claves
Vibraslap
75
D#
4
Claves
76
E
4
Wood Block H
Explosion
Dog
Laughing
77
F
4
Wood Block L
Horse Gallop
Screaming
78
F#
4
4
Cuica Mute
Bird Tweet
Punch
79
G
4
4
Cuica Open
Rain
Heartbeat
80
G#
4
5
Triangle Mute
Thunder
Footsteps 1
5
81
A
4
Triangle Open
Wind
Footsteps 2
82
A#
4
Shaker
Seashore
Applause
83
B
4
Jingle Bell
Stream
Door Creaking
84
C
5
Bell Tree
Bubble
Door Slam
85
C#
5
Castanet
Scratch
86
D
5
6
Surdo Mute
Windchime
87
D#
5
6
Surdo Open
88
E
5
89
F
5
Car Passing
90
F#
5
Crash
91
G
5
Siren
92
G#
5
Train
93
A
5
Jetplain
94
A#
5
Helicopter
95
B
5
Starship
96
C
6
Gunshot
97
C#
6
Machine Gun
98
D
6
Laser Gun
99
D#
6
Explosion
100
E
6
Dog
Engine Start
Applause
Tire Screech
101
F
6
Horse Gallop
102
F#
6
Bird Tweet
103
G
6
Rain
104
G#
6
Thunder
105
A
6
Wind
106
A#
6
Seashore
107
B
6
Stream
108
C
7
Bubble
: Same as Standard kit
: No sound
16
Effect Type List
Effect Type
Description
Effect turned off.
Reverb simulating the resonance of a hall.
Reverb simulating the resonance of a hall.
Reverb simulating the resonance of a room.
Reverb simulating the resonance of a room.
Reverb simulating the resonance of a room.
Reverb appropriate for a solo instrument.
Reverb appropriate for a solo instrument.
Reverb simulating a metal plate reverb unit.
A unique short reverb with a bit of initial delay.
Simulation of a tunnel space expanding to left and right.
A bit of initial delay followed by reverb with a unique resonance.
NO EFFECT
CHORUS1
CHORUS2
CHORUS3
CHORUS4
CELESTE1
CELESTE2
CELESTE3
CELESTE4
FLANGER1
FLANGER2
FLANGER3
Effect turned off.
Conventional chorus program that adds natural spaciousness.
Conventional chorus program that adds natural spaciousness.
Conventional chorus program that adds natural spaciousness.
Chorus with stereo input. The pan setting specified for the Part will also apply to the effect sound.
A 3-phase LFO adds modulation and spaciousness to the sound.
A 3-phase LFO adds modulation and spaciousness to the sound.
A 3-phase LFO adds modulation and spaciousness to the sound.
Celeste with stereo input. The pan setting specified for the Part will also apply to the effect sound.
Adds a jet-airplane effect to the sound.
Adds a jet-airplane effect to the sound.
Adds a jet-airplane effect to the sound.
NO EFFECT
HALL1
HALL2
ROOM1
ROOM2
ROOM3
STAGE1
STAGE2
PLATE
DELAY L, C, R
DELAY L, R
ECHO
CROSS DELAY
EARLY REF1
EARLY REF2
GATE REVERB
REVERSE GATE
KARAOKE 1
KARAOKE 2
KARAOKE 3
CHORUS1
CHORUS2
CHORUS3
CHORUS4
CELESTE1
CELESTE2
CELESTE3
CELESTE4
FLANGER1
FLANGER2
FLANGER3
SYMPHONIC
ROTARY SPEAKER
TREMOLO
AUTO PAN
PHASER1
PHASER2
DISTORTION
OVER DRIVE
AMP SIMULATOR
3BAND EQ (MONO)
2BAND EQ (STEREO)
AUTO WAH (LFO)
Effect turned off.
Reverb simulating the resonance of a hall.
Reverb simulating the resonance of a hall.
Reverb simulating the resonance of a room.
Reverb simulating the resonance of a room.
Reverb simulating the resonance of a room.
Reverb appropriate for a solo instrument.
Reverb appropriate for a solo instrument.
Reverb simulating a metal plate reverb unit.
A program that creates three delay sounds; L, R, and C (center).
A program that creates two delay sounds; L and R. Two feedback delays are provided.
Two delays (L and R) and independent feedback delays for L and R.
A program that crosses the feedback of two delays.
An effect that produces only the early reflection component of reverb.
An effect that produces only the early reflection component of reverb.
A simulation of gated reverb.
A program that simulates gated reverb played backwards.
A delay with feedback of the same types as used for karaoke reverb.
A delay with feedback of the same types as used for karaoke reverb.
A delay with feedback of the same types as used for karaoke reverb.
Conventional chorus program that add natural spaciousness.
Conventional chorus program that adds natural spaciousness.
Conventional chorus program that adds natural spaciousness.
Chorus with stereo input.
A 3-phase LFO adds modulation and spaciousness to the sound.
A 3-phase LFO adds modulation and spaciousness to the sound.
A 3-phase LFO adds modulation and spaciousness to the sound.
Celeste with stereo input.
Adds a jet-airplane effect to the sound.
Adds a jet-airplane effect to the sound.
Adds a jet-airplane effect to the sound.
A multi-phase version of CELESTE.
A simulation of a rotary speaker. You can use AC1 (assignable controller) etc. to control the speed of rotation.
An effect that cyclically modulates the volume.
A program that cyclically moves that sound image to left and right, front and back.
Cyclically changes the phase to add modulation to the sound.
Phaser with stereo input.
Adds a sharp-edged distortion to the sound.
Adds mild distortion to the sound.
A simulation of a guitar amp.
A mono EQ with adjustable LOW, MID, and HIGH equalizing.
A stereo EQ with adjustable LOW and HIGH. Ideal for drum Parts.
Cyclically modulates the center frequency of a wah filter. With an AC1 etc. this can function as a pedal wah.
40
00
THRU
* MSB, LSB is represented in hexadecimal.
* LCB=0 is the basic effect type.
Bypass without applying any effect.
17
MIDI Data Format
NO EFFECT
HALL1
HALL2
ROOM1
ROOM2
ROOM3
STAGE1
STAGE2
PLATE
WHITE ROOM
TUNNEL
BASEMENT
Appendix
Exclusive
MSB
LSB
REVERB
00
00
01
00
01
01
02
00
02
01
02
02
03
00
03
01
04
00
10
00
11
00
13
00
CHORUS
00
00
41
00
41
01
41
02
41
08
42
00
42
01
42
02
42
08
43
00
43
01
43
08
VARIATION
00
00
01
00
01
01
02
00
02
01
02
02
03
00
03
01
04
00
05
00
06
00
07
00
08
00
09
00
09
01
0A
00
0B
00
14
00
14
01
14
02
41
00
41
01
41
02
41
08
42
00
42
01
42
02
42
08
43
00
43
01
43
08
44
00
45
00
46
00
47
00
48
00
48
08
49
00
4A
00
4B
00
4C
00
4D
00
4E
00
Effect Parameter List
No Parameter
Range
Value
See
Table
Control
No Parameter
Range
Value
High Damp
Lch Delay2
Rch Delay2
Delay2 Level
0.1~355.0ms
-63~+63
0.1~355.0ms
-63~+63
0.1~1.0
0.1~355.0ms
0.1~355.0ms
0~127
1-3350
1-127
1-3550
1-127
1-10
1-3550
1-3550
0-127
Dry/Wet
D63>W~D=W~D<W63
1-127
EQ Low Frequency
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
8-40
52-76
28-58
52-76
L->R Delay
R->L Delay
Feedback Level
Input Select
High Damp
0.1~355.0ms
0.1~355.0ms
-63~+63
L, R, L&R
0.1~1.0
1-3550
1-3550
1-127
0-2
1-10
Dry/Wet
D63>W~D=W~D<W63
1-127
EQ Low Frequency
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
8-40
52-76
28-58
52-76
HALL1, HALL2, ROOM 1, 2, 3, STAGE 1, 2, PLATE
ECHO
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Reverb Time
Diffusion
Initial Delay
HPF Cutoff
LPF Cutoff
0.3~30.0s
0~10
0~63
Thru~8.0kHz
1.0k~Thru
0-69
0-10
0-63
0-52
34-60
Dry/Wet
Rev Delay
Density
D63>W~D=W~D<W63
0~63
0~3
1-127
0-63
0-3
13 Er/Rev Balance E63>R ~ E=R ~ E>R63
14
15 Feedback Level -63~+63
16
table#4
table#5
table#3
table#3
•
table#5
1-127
1-127
Reverb Time
Diffusion
Initial Delay
HPF Cutoff
LPF Cutoff
Width
Height
Depth
Wall Vary
Dry/Wet
Rev Delay
Density
Er/Rev Balance
0.3~30.0s
0~10
0~63
Thru~8.0kHz
1.0k~Thru
0.5~10.2m
0.5~20.2m
0.5~30.2m
0~30
D63>W~D=W~D<W63
0~63
0~3
E63>R~E=R~E>R63
Feedback Level -63~+63
0-69
0-10
0-63
0-52
34-60
0-37
0-73
0-104
0-30
1-127
0-63
0-3
1-127
table#4
table#5
table#3
table#3
table#11
table#11
table#11
•
table#5
1-127
Lch Delay
Rch Delay
Cch Delay
Feedback Delay
Feedback Level
Cch Level
High Damp
0.1~715.0ms
0.1~715.0ms
0.1~715.0ms
0.1~715.0ms
-63~+63
0~127
0.1~1.0
1-7150
1-7150
1-7150
1-7150
1-127
0-127
1-10
Dry/Wet
D63>W~D=W~D<W63
1-127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
8-40
52-76
28-58
52-76
•
table#3
table#3
Rch Feedback Level
EQ Low Gain
EQ High Frequency
EQ High Gain
Lch Delay
0.1~715.0ms
Rch Delay
0.1~715.0ms
Feedback Delay1 0.1~715.0ms
Feedback Delay2 0.1~715.0ms
Feedback Level -63~+63
High Damp
0.1~1.0
1-7150
1-7150
1-7150
1-7150
1-127
1-10
Dry/Wet
1-127
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
EQ Low Gain
EQ High Frequency
EQ High Gain
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Type
Room Size
Diffusion
Initial Delay
Feedback Level
HPF Cutoff
LPF Cutoff
Dry/Wet
Liveness
Density
High Damp
D63>W~D=W~D<W63
•
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
S-H, L-H, Rdm, Rvs, Plt, Spr
0.1~7.0
0~10
0~63
-63~+63
Thru~8.0kHz
1.0k~Thru
D63>W~D=W~D<W63
0~10
0~3
0.1~1.0
0-5
0-44
0-10
0-63
1-127
0-52
34-60
table#3
table#3
•
table#3
table#3
table#6
table#5
1-127
0-10
0-3
1-10
Type
Room Size
Diffusion
Initial Delay
Feedback Level
HPF Cutoff
LPF Cutoff
TypeA, TypeB
0.1~7.0
0~10
0~63
-63~+63
Thru~8.0kHz
1.0k~Thru
0-1
0-44
0-10
0-63
1-127
0-52
34-60
Dry/Wet
Liveness
Density
High Damp
D63>W~D=W~D<W63
1-127
0-10
0-3
1-10
50Hz~2.0kHz
8-40
table#3
-12~+12dB
52-76
EQ High Frequency 500Hz~16.0kHz
28-58 table#3
EQ High Gain -12~+12dB
52-76
•
: Can be controlled by AC1 (Assignable Controller 1)
No.*
: T hese numbers correspond to the Parameter Suffix numbers in <Table 1-3>
See Table** : Refer to “Effect Data Assign Table”
EQ Low Frequency
EQ Low Gain
•
•
GATE REVERB, REVERSE GATE
DELAY L, R
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Rch Delay1
EARLY REF1, EARLY REF2
DELAY L, C, R
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Lch Feedback Level
Control
CROSS DELAY
WHITE ROOM, TUNNEL, BASEMENT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Lch Delay1
See
Table
0~10
0~3
0.1~1.0
table#6
table#5
•
No Parameter
Range
Value
See
Table
0-127
1-127
0-52
34-60
table#7
Control
KARAOKE 1, 2, 3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Delay Time
Feedback Level
HPF Cutoff
LPF Cutoff
Dry/Wet
0~127
-63~+63
Thru~8.0kHz
1.0k~Thru
D63>W~D=W~D<W63
1-127
•
table#1
EQ Low Frequency
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
table#3
D63>W~D=W~D<W63
8-40
52-76
28-58
52-76
1-127
mono/stereo
0-1
LFO Frequency
LFO Depth
Feedback Level
Delay Offset
0.00~39.7Hz
0~127
-63~+63
0~63
0-127
0-127
1-127
0-63
table#1
EQ Low Frequency
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
8-40
52-76
28-58
52-76
1-127
table#3
Input Mode
table#2
table#3
•
FLANGER 1, 2, 3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
D63>W~D=W~D<W63
LFO Phase Difference -180~+180deg
LFO Frequency 0.00~39.7Hz
LFO Depth
0~127
Delay Offset
0~127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
table#1
8-40
52-76
28-58
52-76
1-127
table#3
0-127
0-127
0-127
table#1
8-40
52-76
28-58
52-76
table#3
EQ High Gain
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
Input Mode
-180~+180deg
mono/stereo
4-124
0-1
0.00~39.7Hz
0~127
0~127
L<->R, L->R, L<-R,
Lturn, Rturn, L/R
0-127
0-127
0-127
0-5
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
8-40
52-76
28-58
52-76
table#3
LFO Frequency 0.00~39.7Hz
LFO Depth
0~127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
D63>W~D=W~D<W63
•
table#3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
LFO Frequency 0.00~39.7Hz
AM Depth
0~127
PM Depth
0~127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
•
table#3
AUTO PAN
1
2
3
4
table#2
table#3
•
4-124
SYMPHONIC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
0-127
0-127
Control
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
D63>W~D=W~D<W63
0-127
0-127
0-127
table#1
8-40
52-76
28-58
52-76
1-127
table#3
LFO Frequency
L/R Depth
F/R Depth
PAN Direction
5
6 EQ Low Frequency
7 EQ Low Gain
8 EQ High Frequency
9 EQ High Gain
10
11
12
13
14
15
16
table#1
•
table#3
PHASER1, PHASER2
table#2
table#3
•
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
LFO Frequency
LFO Depth
Phase Shift
Feedback Level
0.00~39.7Hz
0~127
0~127
-63~+63
0-127
0-127
0-127
1-127
table#1
EQ Low Frequency
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
8-40
52-76
28-58
52-76
1-127
3-10
0-1
4-124
table#3
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
Stage
Diffusion
LFO Phase Di
D63>W~D=W~D<W63
3~10
Mono/Stereo
-180~+180deg
table#3
•
•
: Can be controlled by AC1 (Assignable Controller 1)
No.*
: T hese numbers correspond to the Parameter Suffix numbers in <Table 1-3>
See Table** : Refer to “Effect Data Assign Table”
19
MIDI Data Format
0-127
0-127
1-127
0-127
EQ High Frequency
See
Table
Appendix
0.00~39.7Hz
0~127
-63~+63
0~127
EQ High Gain
Dry/Wet
Value
TREMOLO
LFO Frequency
LFO PM Depth
Feedback Level
Delay Offset
EQ Low Gain
Range
ROTARY SPEAKER
CHORUS 1, 2, 3, 4, CELESTE 1, 2, 3, 4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
No Parameter
No Parameter
Range
Value
See
Table
Control
DISTORTION, OVERDRIVE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Drive
EQ Low Frequency
EQ Low Gain
LPF Cutoff
Output Level
0~127
50Hz~2.0kHz
-12~+12dB
1.0k~Thru
0~127
500Hz~10.0kHz
-12~+12dB
1.0~12.0
D63>W~D=W~D<W63
Edge (Clip Curve) 0~127
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
Dry/Wet
Drive
AMP Type
LPF Cutoff
Output Level
Dry/Wet
0~127
Off, Stack, Combo, Tube
1.0k~Thru
0~127
•
table#3
table#3
28-54 table#3
52-76
10-120
1-127
0-127 mild ~sharp
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
•
table#3
mild ~sharp
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
EQ Low Gain
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
EQ High Gain
EQ Low Frequency
EQ High Frequency
-12~+12dB
500Hz~10.0kHz
-12~+12dB
1.0~12.0
-12~+12dB
50Hz~2.0kHz
500Hz~16.0kHz
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
52-76
28-54 table#3
52-76
10-120
52-76
8-40
table#3
28-58 table#3
•
: Can be controlled by AC1 (Assignable Controller 1)
No.*
: T hese numbers correspond to the Parameter Suffix numbers in <Table 1-3>
See Table** : Refer to “Effect Data Assign Table”
20
See
Table
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
8-40
52-76
28-58
52-76
table#3
100Hz~10.0kHz
-12~+12dB
1.0~12.0
14-54 table#3
52-76
10-120
LFO Frequency 0.00~39.7Hz
LFO Depth
0~127
Cutoff Frequency 0~127
Resonance
1.0~12.0
3-BAND EQ
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Value
Control
table#3
AUTO WAH
0-127
0-3
34-60
0-127
D63>W~D=W~D<W63 1-127
0-127
Edge (Clip Curve) 0~127
Range
2-BAND EQ
0-127
8-40
52-76
34-60
0-127
GUITAR AMP SIMULATOR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
No Parameter
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
D63>W~D=W~D<W63
0-127 table#1
0-127
0-127
10-120
8-40
52-76
28-58
52-76
1-127
table#3
table#3
•
Effect Data Assign Table
Table#1
Value Data
1.81
86
1.85
87
1.89
88
1.94
89
1.98
90
2.02
91
2.06
92
2.10
93
2.15
94
2.19
95
2.23
96
2.27
97
2.31
98
2.36
99
2.40
100
2.44
101
2.48
102
2.52
103
2.57
104
2.61
105
2.65
106
2.69
107
2.78
108
2.86
109
2.94
110
3.03
111
3.11
112
3.20
113
3.28
114
3.37
115
3.45
116
3.53
117
3.62
118
3.70
119
3.87
120
4.04
121
4.21
122
4.37
123
4.54
124
4.71
125
4.88
126
5.05
127
5.22
Value
5.38
5.55
5.72
6.06
6.39
6.73
7.07
7.40
7.74
8.08
8.41
8.75
9.08
9.42
9.76
10.10
10.80
11.40
12.10
12.80
13.50
14.10
14.80
15.50
16.20
16.80
17.50
18.20
19.50
20.90
22.20
23.60
24.90
26.20
27.60
28.90
30.30
31.60
33.00
34.30
37.00
39.70
Table#5
Value Data
0.0
43
0.1
44
0.2
45
0.3
46
0.4
47
0.5
48
0.6
49
0.7
50
0.8
51
0.9
52
1.0
53
1.1
54
1.2
55
1.3
56
1.4
57
1.5
58
1.6
59
1.7
60
1.8
61
1.9
62
2.0
63
2.1
64
2.2
65
2.3
66
2.4
67
2.5
68
2.6
69
2.7
70
2.8
71
2.9
72
3.0
73
3.1
74
3.2
75
3.3
76
3.4
77
3.5
78
3.6
79
3.7
80
3.8
81
3.9
82
4.0
83
4.1
84
4.2
85
Value Data
4.3
86
4.4
87
4.5
88
4.6
89
4.7
90
4.8
91
4.9
92
5.0
93
5.1
94
5.2
95
5.3
96
5.4
97
5.5
98
5.6
99
5.7
100
5.8
101
5.9
102
6.0
103
6.1
104
6.2
105
6.3
106
6.4
107
6.5
108
6.6
109
6.7
110
6.8
111
6.9
112
7.0
113
7.1
114
7.2
115
7.3
116
7.4
117
7.5
118
7.6
119
7.7
120
7.8
121
7.9
122
8.0
123
8.1
124
8.2
125
8.3
126
8.4
127
8.5
Table#6
Delay Time (ms)
Data Value Data
0
0.1
43
1
1.7
44
2
3.2
45
3
4.8
46
4
6.4
47
5
8.0
48
6
9.5
49
7 11.1
50
8 12.7
51
9 14.3
52
10 15.8
53
11 17.4
54
12 19.0
55
13 20.6
56
14 22.1
57
15 23.7
58
16 25.3
59
17 26.9
60
18 28.4
61
19 30.0
62
20 31.6
63
21 33.2
64
22 34.7
65
23 36.3
66
24 37.9
67
25 39.5
68
26 41.0
69
27 42.6
70
28 44.2
71
29 45.7
72
30 47.3
73
31 48.9
74
32 50.5
75
33 52.0
76
34 53.6
77
35 55.2
78
36 56.8
79
37 58.3
80
38 59.9
81
39 61.5
82
40 63.1
83
41 64.6
84
42 66.2
85
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Room Size (m)
Value Data
67.8
86
69.4
87
70.9
88
72.5
89
74.1
90
75.7
91
77.2
92
78.8
93
80.4
94
81.9
95
83.5
96
85.1
97
86.7
98
88.2
99
89.8
100
91.4
101
93.0
102
94.5
103
96.1
104
97.7
105
99.3
106
100.8
107
102.4
108
104.0
109
105.6
110
107.1
111
108.7
112
110.3
113
111.9
114
113.4
115
115.0
116
116.6
117
118.2
118
119.7
119
121.3
120
122.9
121
124.4
122
126.0
123
127.6
124
129.2
125
130.7
126
132.3
127
133.9
Value
135.5
137.0
138.6
140.2
141.8
143.3
144.9
146.5
148.1
149.6
151.2
152.8
154.4
155.9
157.5
159.1
160.6
162.2
163.8
165.4
166.9
168.5
170.1
171.7
173.2
174.8
176.4
178.0
179.5
181.1
182.7
184.3
185.8
187.4
189.0
190.6
192.1
193.7
195.3
196.9
198.4
200.0
Data Value Data Value
0
0.1
43
6.8
1
0.3
44
7.0
2
0.4
3
0.6
4
0.7
5
0.9
6
1.0
7
1.2
8
1.4
9
1.5
10
1.7
11
1.8
12
2.0
13
2.1
14
2.3
15
2.5
16
2.6
17
2.8
18
2.9
19
3.1
20
3.2
21
3.4
22
3.5
23
3.7
24
3.9
25
4.0
26
4.2
27
4.3
28
4.5
29
4.6
30
4.8
31
5.0
32
5.1
33
5.3
34
5.4
35
5.6
36
5.7
37
5.9
38
6.1
39
6.2
40
6.4
41
6.5
42
6.7
Value
8.6
8.7
8.8
8.9
9.0
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
10.0
11.1
12.2
13.3
14.4
15.5
17.1
18.6
20.2
21.8
23.3
24.9
26.5
28.0
29.6
31.2
32.8
34.3
35.9
37.5
39.0
40.6
42.2
43.7
45.3
46.9
48.4
50.0
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Value
THRU(20)
22
25
28
32
36
40
45
50
56
63
70
80
90
100
110
125
140
160
180
200
225
250
280
315
355
400
450
500
560
630
700
800
900
1.0k
1.1k
1.2k
1.4k
1.6k
1.8k
2.0k
2.2k
2.5k
Reverb Time (ms)
Data
Value
43
2.8k
44
3.2k
45
3.6k
46
4.0k
47
4.5k
48
5.0k
49
5.6k
50
6.3k
51
7.0k
52
8.0k
53
9.0k
54
10.0k
55
11.0k
56
12.0k
57
14.0k
58
16.0k
59
18.0k
60 THRU(20.0k)
Table#7
Table#8
Delay Time (ms)
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Value Data
0.1
43
3.2
44
6.4
45
9.5
46
12.7
47
15.8
48
19.0
49
22.1
50
25.3
51
28.4
52
31.6
53
34.7
54
37.9
55
41.0
56
44.2
57
47.3
58
50.5
59
53.6
60
56.8
61
59.9
62
63.1
63
66.2
64
69.4
65
72.5
66
75.7
67
78.8
68
82.0
69
85.1
70
88.3
71
91.4
72
94.6
73
97.7
74
100.9
75
104.0
76
107.2
77
110.3
78
113.5
79
116.6
80
119.8
81
122.9
82
126.1
83
129.2
84
132.4
85
Data Value Data Value
0
0.3
43
4.6
1
0.4
44
4.7
2
0.5
45
4.8
3
0.6
46
4.9
4
0.7
47
5.0
5
0.8
48
5.5
6
0.9
49
6.0
7
1.0
50
6.5
8
1.1
51
7.0
9
1.2
52
7.5
10
1.3
53
8.0
11
1.4
54
8.5
12
1.5
55
9.0
13
1.6
56
9.5
14
1.7
57 10.0
15
1.8
58 11.0
16
1.9
59 12.0
17
2.0
60 13.0
18
2.1
61 14.0
19
2.2
62 15.0
20
2.3
63 16.0
21
2.4
64 17.0
22
2.5
65 18.0
23
2.6
66 19.0
24
2.7
67 20.0
25
2.8
68 25.0
26
2.9
69 30.0
27
3.0
28
3.1
29
3.2
30
3.3
31
3.4
32
3.5
33
3.6
34
3.7
35
3.8
36
3.9
37
4.0
38
4.1
39
4.2
40
4.3
41
4.4
42
4.5
Reverb Width; Depth; Height
Value Data
135.5
86
138.6
87
141.8
88
144.9
89
148.1
90
151.2
91
154.4
92
157.5
93
160.7
94
163.8
95
167.0
96
170.1
97
173.3
98
176.4
99
179.6
100
182.7
101
185.9
102
189.0
103
192.2
104
195.3
105
198.5
106
201.6
107
204.8
108
207.9
109
211.1
110
214.2
111
217.4
112
220.5
113
223.7
114
226.8
115
230.0
116
233.1
117
236.3
118
239.4
119
242.6
120
245.7
121
248.9
122
252.0
123
255.2
124
258.3
125
261.5
126
264.6
127
267.7
Value
270.9
274.0
277.2
280.3
283.5
286.6
289.8
292.9
296.1
299.2
302.4
305.5
308.7
311.8
315.0
318.1
321.3
324.4
327.6
330.7
333.9
337.0
340.2
343.3
346.5
349.6
352.8
355.9
359.1
362.2
365.4
368.5
371.7
374.8
378.0
381.1
384.3
387.4
390.6
393.7
396.9
400.0
Data Value Data Value Data Value
0
0.5
43 11.8
86 24.2
1
0.8
44 12.1
87 24.5
2
1.0
45 12.3
88 24.9
3
1.3
46 12.6
89 25.2
4
1.5
47 12.9
90 25.5
5
1.8
48 13.1
91 25.8
6
2.0
49 13.4
92 26.1
7
2.3
50 13.7
93 26.5
8
2.6
51 14.0
94 26.8
9
2.8
52 14.2
95 27.1
10
3.1
53 14.5
96 27.5
11
3.3
54 14.8
97 27.8
12
3.6
55 15.1
98 28.1
13
3.9
56 15.4
99 28.5
14
4.1
57 15.6
100 28.8
15
4.4
58 15.9
101 29.2
16
4.6
59 16.2
102 29.5
17
4.9
60 16.5
103 29.9
18
5.2
61 16.8
104 30.2
19
5.4
62 17.1
20
5.7
63 17.3
21
5.9
64 17.6
22
6.2
65 17.9
23
6.5
66 18.2
24
6.7
67 18.5
25
7.0
68 18.8
26
7.2
69 19.1
27
7.5
70 19.4
28
7.8
71 19.7
29
8.0
72 20.0
30
8.3
73 20.2
31
8.6
74 20.5
32
8.8
75 20.8
33
9.1
76 21.1
34
9.4
77 21.4
35
9.6
78 21.7
36
9.9
79 22.0
37 10.2
80 22.4
38 10.4
81 22.7
39 10.7
82 23.0
40 11.0
83 23.3
41 11.2
84 23.6
42 11.5
85 23.9
21
MIDI Data Format
Value Data
0.00
43
0.04
44
0.08
45
0.13
46
0.17
47
0.21
48
0.25
49
0.29
50
0.34
51
0.38
52
0.42
53
0.46
54
0.51
55
0.55
56
0.59
57
0.63
58
0.67
59
0.72
60
0.76
61
0.80
62
0.84
63
0.88
64
0.93
65
0.97
66
1.01
67
1.05
68
1.09
69
1.14
70
1.18
71
1.22
72
1.26
73
1.30
74
1.35
75
1.39
76
1.43
77
1.47
78
1.51
79
1.56
80
1.60
81
1.64
82
1.68
83
1.72
84
1.77
85
Table#4
EQ Frequency (Hz)
Modulation Delay Offset (ms)
Appendix
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
Table#3
Table#2
LFO Frequency (Hz)
YAMAHA [Disklavier]
MIDI IMPLEMENTATION CHART
Model: Mark III Full-Function
Transmitted
Function...
Remarks
Recognized
Memorized
Basic
Channel
Default
Changed
1-16
1-16
1-16
1-16
3
Mode
Default
Messages
Altered
3
3, 4 (m=1)
Note
Number :
×
****************
×
0-127
True voice
****************
0-127
0-127
Velocity
Note ON
Note OFF
O 9nH, v=1-127
O
O v=1-127
O
After
Touch
Key s
Ch s
O
*5
*2, *3
×
O
O
*1, *2
×
O
0-24 semi *1, *2
O
O
*1, *2
*1
*1, *2
*2
×
×
×
O
O
O
O
O
O
O
O
O
O
O
Prog
Change : True #
O 0-127
O
System Exclusive
O
: Song Pos
Common : Song Sel
: Tune
O
O
System
Real Time
O
O
Pitch Bend
0, 32
7, 11
1, 5, 10
6, 38
64
65
66
67
71-74, 84
91, 93, 94
96-101
Control
Change
Aux
Messages
Notes
: Clock
: Commands
: All Sound OFF
: Reset All Cntrls
: Local ON/OFF
: All Notes OFF
: Active Sense
: Reset
×
×
O
×
O
O
*4
*2
*2
*2
*2
*1, *2
0-127
Bank Select
Data Entry
Hold1 (Sustain)
Portament
Sostenuto
Soft (Shift) Pedal
Effect Depth
*2
****************
O
*1
*1
×
O
O
*1
*1
×
×
*1
O
*1
O (120, 126, 127)
O (121)
O
O (123-125)
O
O
×
×
O
O
×
×
*1 = Received (transmitted) if switch is on.
*2 = Only ESBL Part can recognize.
*3 = m is always treated as 1 regardless of its value.
*4 = Transmit if this model has a Sostenuto Pedal.
Mode 1 : OMNI ON. POLY
Mode 3 : OMNI OFF. POLY
Date : 01-Feb-2000
Version : 1.00
*5 = Applying further pressure on the key does not output
key aftertouch information. Instead, key position is
transmitted as additional information.
Mode 2 : OMNI ON. MONO
Mode 4 : OMNI OFF. MONO
O : Yes
× : No
Basic (A) スミ Pantone 282C