Zavio N6031 User manual

Add to my manuals
102 Pages

advertisement

Zavio N6031 User manual | Manualzz

N6031 User Manual

0

N6031 User Manual

N6031 IP Camera

Firmware User Manual

- Contents -

CHAPTER 1. MINIMUM SYSTEM REQUIREMENT............................................................................................... 2

CHAPTER 2. USING IP CAMERA VIA WEB BROWSER ........................................................................................ 3

CHAPTER 3. USING IP CAMERA VIA MOBILE PHONE....................................................................................... 8

3.1

U SING IP C AMERA VIA I P HONE ............................................................................................................................... 8

3.2

M OBILE P HONE V IEWING ....................................................................................................................................... 9

CHAPTER 4. MSN MESSENGER............................................................................................................................... 10

CHAPTER 5. CONFIGURATION OF MAIN MENU................................................................................................ 15

5.1

L IVE V IEW ............................................................................................................................................................. 16

5.2

S ETTING ................................................................................................................................................................. 18

5.3

C LIENT S ETTING ................................................................................................................................................... 19

5.4

I MAGE S ETUP ......................................................................................................................................................... 20

CHAPTER 6. SETTING-BASIC................................................................................................................................... 21

6.1

S YSTEM .................................................................................................................................................................. 22

6.2

C AMERA ................................................................................................................................................................. 27

6.3

N ETWORK .............................................................................................................................................................. 33

6.4

S ECURITY ............................................................................................................................................................... 47

CHAPTER 7. SETTING-ADVANCE ........................................................................................................................... 50

7.1

FTP C LIENT ........................................................................................................................................................... 51

7.2

SMTP .................................................................................................................................................................... 59

7.3

HTTP EVENT ......................................................................................................................................................... 69

7.4

A LARM O UTPUT .................................................................................................................................................... 76

7.5

S CHEDULE .............................................................................................................................................................. 80

7.6

A LARM I NPUT ........................................................................................................................................................ 82

7.7

A LARM BUFFER ...................................................................................................................................................... 83

7.8

M OTION D ETECTION ............................................................................................................................................. 84

7.9

S YSTEM L OG .......................................................................................................................................................... 86

CHAPTER 8. APPENDIX ............................................................................................................................................. 87

1

Firmware User Manual

N6031 User Manual

Chapter 1. Minimum System Requirement

We strongly recommend your computers follow our minimum requirements in order to use this

IP-Camera normally. If computer level is lower than this, it might cause some problems.

Item Requirements

CPU Pentium 4 1600MHz (or equivalent AMD)

Graphic Card

RAM

64 MB RAM graphic cards(or equivalent on-board graphic cards)

512 MB

Operating System Windows 98, Windows ME (Please see Note)

Windows2000, 2003, XP, Vista, Mac OS X Leopard

Web Browser Internet Explore 6 or later

Note:

1. If you are using Windows 98 or Windows ME, please install IP Installer before using WEB UI to ensure the system runs normally.

2. If you can't view the record video file, please install Xvid codec while installing Intelligent IP

Installer. (For Windows 98, ME or 2000 server, the codec might not work properly. You’ll need to download Xvid codec 1.0 from the internet.

3. Please always update the latest Windows component. (.Net Framework, Windows Media Player,

Enhance ActiveX Security)

2

Chapter 2. Using IP Camera via Web Browser

2.1Windows Web Browser

1. Start your web browser, and enter the IP address or host name of the IP camera in the

Location / Address field of your browser.

Note :

If you only want to view the video without setting page, enter “ http://<IP>/index2.htm

” as your web URL.

2. Use the default account “admin” and default password “admin”.

Note :

The default user name “admin” and the password are set at the factory for the administrator. You can change them in the Account Menu (Please check “Setting →

Basic → Security → Account”)

3

3. The monitor image will be displayed in your browser. In the far left side of main configuration are Setting, Client Setting, and Image Setup. For more details, you can check

Chapter 5.2Chapter 5.3 and Chapter 5.4.

4

2.2 Mac Web Browser

1. Click the Safari icon, and enter the IP address of the IP camera in the Location / Address field of your browser.

Note :

If you only want to view the video without setting page, enter “ http://<IP>/index2.htm

” as your web URL.

5

2. Use the default account “admin” and default password “admin”.

Note :

The default user name “admin” and the password are set at the factory for the administrator. You can change them in the Account Menu (Please check “Setting →

Basic → Security → Account”)

6

3. The monitor image will be displayed in your browser. In the far left side of main configuration are Setting, Client Setting, and Image Setup. For more details, you can check

Chapter 5.2Chapter 5.3 and Chapter 5.4.

7

Chapter 3. Using IP Camera via Mobile Phone

3.1 Using IP Camera via iPhone

You can use Zavio Web User Interface via iPhone. Please follow the setting process below.

Then you can use Zavio web UI via iPhone.

1. Select Safari function

3. Type name and password.

Default value is admin / admin.

Then click Login In

2. Enter IP address in your web link.

4. The Zavio User Interface and live image will show up in the middle of screen.

Note: It will show continuous snapshots not a real time video streaming. Therefore, the recording feature is disabled.

8

3.2 Mobile Phone Viewing

To use IP cameras via mobile phones, please make sure your RTSP is set to “On” (Default is

“On”). To change the settings of IP cameras, Please check “Settings → Basic → Camera →

General.”

1. 3G Mobile Phone Streaming Viewing

For 3G mobile phone viewing, type “ rtsp://<IP>:<PORT>/video.3gp ” into your 3G

Streaming Link. <IP> is the Public IP address of your IP camera; <PORT> is the RTSP port of your IP camera (Default value is 554.) Example: rtsp://100.10.10.1:554/video.3gp

Note: You can also use RTSP clients (RealPlayer, VLC, QuickTime Player…etc.) to view RTSP streaming, just type in “ rtsp://<IP>:<PORT>/video.3gp

” as the Player URL

2. 2.5G Mobile Phone WAP Viewing

For 2.5G mobile phone viewing, type “ <IP>/mobile.wml ” into your 2.5G WAP Browser.

<IP> is the Public IP address of your IP camera.

3. 2.5G Mobile Phone Browser Viewing

For 2.5G mobile phone viewing, type “ <IP>/mobile.htm ” into your 2.5G Web Browser.

<IP> is the Public IP address of your IP camera.

9

Chapter 4. MSN Messenger

Please see the following steps to set up the Messenger function.

1. You can download MSN software freely and create a new MSN account (camera at home) to use Microsoft Live Messenger.

2.Go to Setting→Basic→Network→Messenger , set the Messenger to “ON” . Then, login in new account and password (Camera at home).

3. Choose “On” at the option of IP Notification. If this feature switches On, camera will send

IP notification to the users who are allowed.

4. Choose “On” at the option of Privacy. If you can choose “On” at the privacy option, you can set an allow list.

5. Use your account to login in the Messenger software. Then, add the new MSN account (Camera

at home )

10

6. The Camera at home will show up with its Public IP and Private IP if the option of IP

Notification is “On”. ( You can enter “Ping” to show up with Public IP and Private IP. )

. Then, choose “View a new contact's webcam”. 7. Click on the small camera icon

Camera at home says:

8. The IP Camera will accept your invitation; the live video will show up in the right screen after few seconds.

11

9. Click Action button and choose Start control panel to use control panel.

10. The dialog box will show up with “This application is not part if Window Live Message…….”

Tick the box of “Don’t show me this again” and click OK

12

11. The IP Camera will accept your invitation to start Control Panel.

12. You can click Camera icon to snapshot then the picture will send to you immediately.

Snapshot

13

13. You can click paint palette icon showing up with tool bar to set up image. Then, you can use the tool bar to optimize video Brightness , Contrast , Saturation and Hue .

After the adjustment of all setting, you can still click original setting.

to make the setting back to the

Image Setup

14

Chapter 5. Configuration of Main Menu

In the far left side of main configuration are Setting, Client Setting, Image Setup. For more

details, you can check Chapter 5.2Chapter 5.3Chapter 5.4.

Snapshot

Full screen

Zoom in / Out

Video Play Audio button

In your right hand side, you can use Live View in your main Browser. There are Snapshot,

Zoom and Audio and Video Play four different function. You can see more details as follow.

15

5.1 Live View

A. Snapshot

B. You can capture a still image shot by the camera and save it in your computer.

Symbols Meaning a snapshot window will appear

Save to save the picture in your computer

Close to return to the view page full Screen

B. Zoom in / out the image via the monitor window

Click to display the digital zoom in window.

Pull the be showed on the above window.

to adjust the digital zoom range, and it will

You can use the left click of your mouse to move the to any where on the window.

16

C. Video play buttons

Symbols Meaning

Pause the current video

Play the video

Stop the current video

Record the current video

Note:

Concerning the recording storage requirement of your hard disk, please refer to the CHAPTER 8. APPENDIX / B. Storage Requirement Table.

D. Audio buttons

Symbols Meaning

Speakers turned on

Speakers turned off

Microphone turned on

Microphone turned off

Volume control bar

Note mean the speakers of your computer are turned on to transmit the sounds from the connected IP camera(s) mean you can broadcast to the connected IP camera(s) via the Ethernet using your microphone

17

5.2 Setting

This function is only for the Administrator. Click this button to get into the Basic and

Advance settings menu.

Click Basic folder, there are four sub-folders including System, Camera, Network, and

Security. Fore more information, you can see Chapter 6.1、Chapter 6.2、Chapter 6.3 and

Chapter 6.4.

Click Advance folder, there are four sub-folders including FTP Client, SMTP, HTTP

event, Alarm output, Schedule, Alarm input, Motion Detection, and System Log. Fore more information, you can see Chapter 7.1、Chapter 7.2、Chapter 7.3、Chapter 7.4、Chapter

7.5、Chapter 7.6、Chapter 7.7、Chapter 7.8、Chapter 7.9.

18

5.3 Client Setting

This function is only for the client.

Click this button to control Mode, View Size, Protocol, and Video Buffer.

5.3.1 Mode

Click the pull-down box to choose between MPEG4 and MJPEG video compression mode.

MJPEG streaming is unavailable if RTSP mode is “On.”

(Please check Setting → Basic → Camera → General)

NoteMJPEG streaming is unavailable if RTSP mode is On.

5.3.2 View Size

Select the desired display image resolution to 640X480 or 320X240.

5.3.3 Protocol

Select the transferring protocol from TCP, UDP, HTTP and Multicast.

5.3.4 Video Buffer

Turn the Video Buffer function ON / OFF. The Video Buffer function makes the streaming more smoothly in unsteady network environment, but might cause a little delay in live viewing.

19

5.4 Image Setup

You can use the tool bar to optimize video Brightness, Contrast, Saturation and Hue.

5.4.1 Brightness

The higher value the brightness is, the brighter the image is.

5.4.2 Contrast

The contrast is a measure of a display system, defined as the ratio of white to black that the system is capable of producing. The higher value the contrast is, the more delicate of color you can have.

5.4.3 Saturation

The saturation of a color is determined by a combination of light intensity and how much it is distributed across the spectrum of different wavelengths. The higher value the saturation is, the more colorful the image will be .

5.4.4 Hue

Hue is one of the three main attributes of perceived color, affected by different wavelength of color. With higher value of hue, color will be much more vivid.

5.4.5 Default

After the adjustment of all setting, you can still click Default to make the setting back to the original setting.

20

Chapter 6. Setting-Basic

Click the folder of Basic to display the sub folders including System, Camera, Network, and

Security.

21

6.1 System

Click the folder of System to display the sub-folders including Information, Date / Time, and Initialize.

22

6.1.1 Information

The Information page provides the product factory information which includes Product

Name, Firmware Version and Web Version.

23

6.1.2 Date / Time

The Date/ Time page displays all options of time setting.

Current date / time: This displays the current date and time of this IP Camera.

PC clock: This displays the date and time of the monitoring PC clock.

Date / Time format: You can click the pull down box to select different time display formats.

Adjust: You can select one of those four adjusting modes for your IP Camera.

Keep current setting: Select this mode to keep the current date and time of this IP

Camera.

Synchronize: Select this mode to keep the date and time of this IP Camera is the same as the monitoring PC.

Manual setting: Select this mode to adjust manually the date and time of this IP

Camera.

Synchronize with NTP: Specify the NTP server name and the Refresh Interval to synchronize the date and time of this IP Camera with those of the time server, known as the NTP server.

Time Zone: You can select the Time Zone of the format from Greenwich Mean Time.

The time will display the same as the current date / time option.

Note:

The NTP server (Network Time Protocol) is the time server which is an Internet standard protocol built on the top of TCP / IP. This assures accurate synchronization to the millisecond of computer clock times in a network of computers.

24

6.1.3 Initialize

Reboot: Click this bottom to reboot this IP Camera. A confirmation dialogue will appear and then click “OK” to process. It takes two minutes to reboot this IP Camera.

Factory Default: Click this bottom to reset this IP Camera to the factory default setting.

A confirmation dialogue will appear and then click “OK” to process. The network indicator on this IP Camera will start to blink. This IP Camera will reboot automatically after completing adjustments to the default setting. Don't turn off this IP Camera until the device reboots.

Backup Setting: You can save the setting data of this IP Camera into a file. Click “Save” and follow the instructions on the browser to save the setting data file to your specified location.

Restore Setting: Download the saved setting data of this IP Camera. Click “Browse” and select saved file. Click “OK” and this IP Camera is adjusted according to the loaded data and then restarted.

Firmware Update: Upgrade the device software. Click “Browse” and select the file for upgrading. A confirmation dialogue will appear. Click “OK” to start upgrading. This IP

Camera will reboot upon completion.

Note:

Use only upgrade files that are special for this IP Camera. Otherwise problems may occur. Don't turn off the IP Camera power or disconnect the network until the upgrading is completed.

25

Upload Language Pack: Upgrade the device language pack. Click “Browse” and select the file for upgrading. A confirmation dialogue will appear. Click “OK” to start upgrading.

The upgrade is applied immediately. The default language is “English.”

26

6.2 Camera

Click the folder of Camera to display the sub folders including General, MPEG4 and

MJPEG.

27

6.2.1 General

RTSP : Switch On / Off

Note: RTSP (Real Time Streaming Protocol) is a protocol for use in streaming media system which allows clients to remotely control a streaming video server.

RTSP is supports by most of the media clients such as Real Player, QuickTime and VLC...etc.

Image Rotate: You can mirror or flip the display screen.

Night Mode: You can choose Auto / Off. If you choose Auto option, the camera will adjust automatically to perform well when the environment is dark

Lighting: You can choose the environment among 50 Hz, 60 Hz , and Outdoor.

White Balance: You can choose the white balance to Auto, Florescent, Incandescent and

Black & White.

Overlay:

Text Overlay: You can see some information on the display screen which includes

Date / Time and user-defined text. Also, you can change the background color.

Privacy Mask: You can cover a specific area of the video image.

28

6.2.2MPEG4

A. Computer View

RTSP (if RTSP mode is On, please check “Setting → Basic → Camera → General ”)

RTSP Port: Specify the transmission port number of RTSP streaming. The default value is 8554.

Viewer Authentication: If the viewer authentication is On, the users will be requested to key-in username and password when viewing through RTSP.

RTP (if RTSP mode is On, please check “Basic→ Camera → General“)

Unicast Streaming Video / Audio Port Range: Specify the transmission port range of

RTP streaming video. RTP will select a port randomly from the range.

Multicast Streaming (If it is ON)

Multicast Address: Specify the multicast server address.

Video / Audio Port: Specify the transmission port number of the video data. Specify an even number from 1024 to 65534.

Time to Live: Set the maximum TTL that multicast can pass through.

Image Size: Specify the image size when the network camera transmits. You can choose among 640 x 480, 320 x 240, and 160 x 120.

Frame Rate: Set the frame rate of the MPEG4 image. You can choose values from 5, 10,

15, 20, 25, and 30 fps. The unit “fps” stands for “frames per second”.

Quality:

Auto: The quality and bitratee will be adjusted automatically according to the frame rate.

Fixed Quality: You can select the value of quality among Medium, Good, Delicate

29

and Excellent.

Fixed Bitrate: Set the bitrate of MPEG4 image transmission for a line. You can select the values from 64, 128, 256, 384, 512, 768, 1024, 1280, 1536, and 2048 kbps.

MPEG4 view port (if RTSP mode is Off, please check “Basic → Camera →

General”)

Unicast Streaming Video / Audio Port Number: Specify the transmission port number of the video data. It is initially set to 8090. You can specify an even number from 1024 to 65534. If you change the setting of Video / Audio Port Number, the setting of Video / Audio Port Number (SSL) will change automatically.

Note:

Concerning how to select the suitable image quality for Fixed Quality or Fixed Bitrate, please refer to the CHAPTER 8. APPENDIX / A. Frame-rate & Bitrate Table.

30

B. Mobile View

RTSP (if RTSP mode is On, please check “Setting → Basic → Camera → General”)

RTSP Port: Specify the transmission port number of RTSP streaming. The default value is 554.

RTP (if RTSP mode is On, please check “Setting → Basic → Camera → General”)

Unicast Streaming Video / Audio Port Range: Specify the transmission port range of

RTP streaming video. RTP will select a port randomly from the range.

Multicast Streaming (If it is On)

Multicast Address: Specify the multicast server address.

Video / Audio Port: Specify the transmission port number of the video data. It is

 initially set to 10000 and 11000. Specify an even number from 1024 to 65534.

Time to Live: Set the maximum TTL that multicast can pass through.

Image Size: The image size of Mobile View is fixed at 160 x 120.

Frame Rate: Set the frame rate of the MPEG4 image. You can choose values from 5, 10,

15, 20 fps. The unit “fps” stands for “frames sent per second”.

Quality:

Fixed Bitrate: Set the bitrate of MPEG4 image transmission for a line. You can select the value from 64, 32, 16 kbps.

Note:

Concerning how to select the suitable image quality for Fixed Quality or Fixed Bitrate, please refer to the CHAPTER 8. APPENDIX / A. Frame-rate & Bitrate Table.

31

6.2.3 MJPEG

MJPEG Viewer Port( If RTSP is off, please check “Setting → Basic → Camera →

General”):

Unicast Streaming Video / Audio Port Number: Specify the transmission port number of the video data. It is initially set to 8070. You can specify an even number from 1024 to 65534. If you change the setting of Video / Audio Port Number, the setting of Video

/ Audio Port Number (SSL) will change automatically.

Image Size: Specify the image size when the network camera transmits. You can choose among 640 x 480, 320 x 240, and 160 x 120.

Frame Rate: Set the frame rate of the MJPEG image. You can choose values from 5, 10,

15 fps. The unit “fps” stands for “frames per second”.

Quality:

Auto: The quality will be automatically decided.

Fixed Quality: You can select the value of quality among Medium, Standard, Good,

Delicate and Excellent.

Note:

Concerning how to select the suitable image quality for Fixed Quality or Fixed Bitrate, please refer to the CHAPTER 8. APPENDIX / A. Frame-rate & Bitrate Table.

32

6.3 Network

Click the folder of Network to display the sub folders including Information, PPPoE,

DDNS, UPnP, Bonjour, IP Notification, and Messenger.

33

6.3.1 Information

Display the MAC address of the device.

Obtain an IP address automatically (DHCP): If a DHCP server is installed on the network, to select this while the IP address is assigned by the DHCP server.

Obtain DNS server address automatically: Select this to obtain the address of DNS server automatically.

34

Use the following IP address: Select this when the fixed IP address is set.

IP address: Enter the IP address of the device.

Subnet mask: Enter the subnet mask.

Default gateway: Enter the default gateway.

Use the following DNS server address: Select this when you set the fixed address as the

IP address of DNS server.

Primary DNS server: Enter the IP address of the primary DNS server.

Secondary DNS server: Enter the IP address of the secondary DNS server, if necessary.

HTTP port number: Select 80 in general situations. If you want to use a port number other than 80, select the text box and enter a port number between 1024 and 65535.

When you have set the HTTP port number to a number other than 80 on the Network setting page or in the Setup Program, access the device by typing the IP address of the device on the web browser as follows: Example: when HTTP port number is set to

2000 http://192.168.1.100:2000/

Note: The IP Camera needs to be rebooted after it finishes changing the network setting

completely.

Note: If you connect the IP Camera with your computer directly, the default network domain of camera is 192.168.1.xx

35

6.3.2 PPPoE (Point-to-Point Protocol over Ethernet)

If your ISP provides Dynamic IP with authentication by username and password, type all

PPPoE information in this part. When you use the PPPoE function, you need to turn on the

DDNS or IP Notification function at same time.

IP address: The IP address obtained at the PPPoE connecting with network.

User ID: Enter the user ID for authentication necessary for PPPoE connections. Type it up to 64 characters.

Password: Enter the password for authentication necessary for PPPoE connections. Type it up to 32 characters.

Re-type password: Re-type the password to confirm.

Obtain DNS server address automatically: Select this to obtain the address of DNS server automatically.

36

Use the following DNS server address: Select this when you set the fixed address as the

IP address of DNS server.

Primary DNS server: Enter the IP address of the primary DNS server.

Secondary DNS server: Enter the IP address of the secondary DNS server.

Note :

1. PPPoE (Point-to-Point Protocol over Ethernet): PPPoE is a network protocol for encapsulating Point-to-Point Protocol frames insider Ethernet frames. PPPoE connection is used mainly with ADSL service where individual users connect to the

ADSL transceiver (modem) over Ethernet work. It also widely used in XDSL (digital affiliate line such as ADSL, VDSL or SDSL)

2. The IP Camera needs to be rebooted after it finishes changing the network completely.

3. The IP Camera with Intelligent IP Installer can’t be founded after turning on the PPPoE and reboot.

37

6.3.3 DDNS (Dynamic DNS)

DDNS is a system which allows the domain name data held in a name server to be updated in real time. The most common use for DDNS is allowing an internet domain name to be assigned to a computer with a varying / dynamic IP Address. This makes it possible for other sites on the internet to establish connection to the machine without needing to track the IP

Address themselves.

Server name: Choose the DDNS Server from the list.

User ID: Enter the user ID for authentication necessary for DDNS connections. Type it up to 64 characters.

Password: Enter the password for authentication necessary for DDNS connections. Type it up to 32 characters.

Re-type password: Re-type the password to confirm.

Host name: Enter the host name that is registered to the DDNS server.

38

Note :

How to apply DDNS username and Host name??

You can apply DDNS username and Host name by the following steps:

1. Login http://www.dyndns.org

, click the Create Account

2. Input all information and follow step by step with DynDNS

.

39

3. Login with new account and click Account → My Hosts → Add Host Services

4. Type domain in the Hostname field and select sub-domain

40

5. After type information, check your DDNS service.

6. Type your DDNS User ID, Password and Host name in Setting → Network →

DDNS. After completing setting, reboot IP Camera.

41

6.3.4 UPnP (Universal Plug and Play)

If you have a Router to access to internet and the Router supports UPnP IGD function, you need to turn on the UPnP Port Forwarding function.

HTTP port: Enter the HTTP port number and default HTTP port is 80.

SSL port: Enter the SSL port number and default SSL port is 443.

MPEG4 viewer port: Enter the MPEG4 viewer port number and default MPEG4 viewer port is 8090.

MPEG4 viewer port (SSL): Enter the MPEG4 SSL viewer port and default is 8091.

MJPEG viewer port: Enter the MJPEG viewer port number and default MJPEG viewer port is 8070.

MJPEG viewer port (SSL): Enter the MPEG4 SSL viewer port and default is 8071.

MPEG4 RTSP port: Enter the MPEG4 RTSP port, default value is 8050 for computer view, 8030 for mobile view.

Note :

UPnP (Universal Plug and Play): UPnP is a set of computer network protocol. It allows devices to connect seamlessly and simplify the implementation of networks in the home and corporate environments. The device supports UPnP which is enabled by default.

The device will be automatically detected and a new icon will be added to “My

Network Place” if it also enables on your computer. It provides Port Forwarding for opening a port in a router or firewall in a private network in order to let a party from the outside world contact a inside user.

42

6.3.5 Bonjour

Bonjour, also known as zero-configuration networking, enables automatic discovery of computers, devices, and services on IP networks. Bonjour uses industry standard IP protocols to allow devices to automatically discover each other without the need to enter IP addresses or configure DNS servers.

Device Name: Enter Device Name you wish.

Note: How to use Bonjour in your Windows Browser UI? Please check the link below: http://www.apple.com/support/downloads/bonjourforwindows.html

43

6.3.6 IP Notification

When network notify type is set to “ON”, you can send an e-mail notification of the completion of the network setting.

Notify Type: You can select the notify type among DHCP, Static IP, and PPPoE.

SMTP Server Name: Type the SMTP server name up to 64 characters, or the IP address of the SMTP server.

SMTP Server Port: You can set port number from 1~65535 according to your mail server. The default value is 25.

Security setting: Tick SSL box if the mail server you use has security restriction.

Note:

If you use g-mail as your mail server, you should set 587 as your port number and tick

SSL box.

Authentication: Select the authentication required when you send an email.

Off: Select if no authentication is necessary when an email is sent.

On: When authentication is necessary an e-mail is sent, there are SMPT, POP before

SMPT or both three options.

44

Authentication: Select the authentication required when you send an email.

Off: Select if no authentication is necessary when an email is sent.

On: When authentication is necessary an e-mail is sent, there are SMPT, POP before

SMPT or both three options.

SMTP: Select if SMTP authentication is necessary when an e-mail is sent.

POP before SMTP: Select if POP before SMTP authentication is necessary when an e-mail is sent.

POP server name: It is necessary when the POP before SMTP is selected in

Authentication. Type the POP (receiving mail) server name up to 64 characters, or type the IP address of the POP server. This setting is necessary when the SMTP server which sends e-mails performs authentication using the POP user account.

User name, Password: Type the user name and Password of the user who has the mail account. This setting is necessary when the SMTP server which sends e-mails performs authentication.

Recipient e-mail address: Type the recipient e-Mail address up to 64 characters. You can specify up to three recipient E-mail addresses.

Administrator e-mail address: Type the Administrator e-Mail address up to 64 characters. This address is used for reply mail and sending system messages from the SMTP server.

Subject: Type the subject/title of the e-Mail up to 64 characters. With respect to mail which is sent according to the IP notification.

Message: Type the text of the E-mail up to 384 characters. Default value provides network information including IP, Port, MAC, Model, Firmware Version and Web Version.

45

6.3.7 Messenger

Messenger function provide an easy-connect feature. User can easy to know what camera’s private and public IP address is.

Protocol: support MSN only.

Login Account: Camera will use this account to login MSN server. This MSN account should be applied form http:// www.msn.com

.

Password: password for this msn account.

Re-type password: re-type password to double confirm.

Alias: This alias will display on MSN like the following which display in red frame.

Port range: Camera will select one port from this port range for video transmission.

IP Notification: Switch the IP notification On / Off. If this feature switches On, camera will send IP notification to the users who are allowed.

Privacy: Switch privacy On / Off. When privacy turns on, only those users in allowed list can access the camera.

User: Input to this blank to edit allow list.

Allow list: When privacy turns on, only those users in allow list can access the camera.

46

6.4 Security

Click the folder of Security to display the sub folders including Account and HTTPS.

47

6.4.1 Account

The device fault account and password setting is “admin / admin”. That means everyone who knows IP address can access the device including all configuration. It is necessary to assign a password if the device is intended to be accessed by others.

User name: Set a user name between 4-16 characters.

Password: Set a password between 4-16 characters.

Re-type Password: Re-type the password to confirm.

Viewer Mode: Set the user mode among Admin, Operator, and Viewer. Different viewer mode has different limits of authority.

The Admin mode has all authority of configuration.

The Operator mode can not only view the Live View but also control the PTZ (apply in speed dome).

The Viewer mode only can view the Live View.

Viewer Authentication: Allows any viewer direct access to Live View.

48

6.4.2 HTTPS

HTTPS is a URI scheme used to indicate a secure HTTP connection. It is syntactically identical to the http:// scheme normally used for accessing resources using HTTP. Using an https: //URL/ with a different default TCP port (443) and an additional encryption / authentication layer between the HTTP and TCP. You can use the IP camera through HTTPS easily by using https:// instead of http://.

Create & Install: Create a self-signed certificate for HTTPS to recognize.

Installed Certificate: Display or remove the properties of the installed certificate.

HTTPS Connection Policy: Set HTTPS connection policy for different level of users.

 To use the HTTPS encryption, please set up “Create self-signed certificate” for the first time you use the HTTPS function, and then set up the connection policy for different users.

Note:

When enable HTTPS with RTSP on mode, the IP Camera only protect the setting such as username and password and do not protect video and audio. When enable HTTPS with RTSP off mode, the IP Camera will protect all setting including video and audio.

49

Chapter 7. Setting-Advance

Click the folder of Advance to display the sub folders including FTP client, SMTP, HTTP event, Alarm output, Schedule, Alarm input, Alarm buffer, Motion detection and System

Log.

50

7.1 FTP Client

Use this menu to set up for capturing and sending images to an FTP server. By using FTP client function, you can send the image and video file which has been shot and recorded linked with the external sensor input or with the built-in motion detection function to FTP server. FTP client setting menu is composed of two tabs, General, Alarm sending and Periodical sending.

51

7.1.1 General

Select “On” when you use FTP function. The FTP client setting page appears.

Select “Off”, when you do not wish to use the FTP client function.

Note:

The frame rate and operability on the main viewer may decrease while a file is being transmitted by the FTP client function.

FTP server name: Type the FTP server name to upload still images up to 64 characters, or the IP address of the FTP server.

User name: Type the user name for the FTP server.

Password: Type the password for the FTP server.

Retype password: To confirm the password, type the same characters as you typed in the

Password box.

Passive mode: Set whether you use the passive mode of FTP server or not when connecting to FTP server. Select On to connect to FTP server using the passive mode.

Attached file type: You can choose the attached file in JPEG or MPEG4 type.

52

7.1.2 Alarm sending

Set to forward the image and audio file to the specified FTP server linked with the alarm detection by the external sensor input or by the built-in motion detection function. Select On to send the image file to FTP server linked with the alarm detection.

Remote Path: Type the path to the destination in FTP server up to 64 characters.

Image File Name: Type the file name you want to assign to the images when sending to the FTP server. You can use up to 10 alphanumeric characters, - (hyphen) and _

(underscore) for naming.

Suffix: Select a suffix to add to the file name

Date & time: The date & time suffix is added to the Image file name. The date/time suffix consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2 digits), minute (2 digits), second (2 digits), and consecutive number (2 digits), thus 14-digit number is added to the file name.

Sequence number: A consecutive number of 10 digits between 0000000001 and

4294967295 and two fixed digits 00 is added to the Image file name.

Sequence number clear: Click Clear and the suffix of the sequence number returns to 1.

53

Alarm

Motion Detection: Click it on for using Motion Detection function as a sensor. You can set motion detection function at the motion detection function page.

Note: You can set motion detection at motion detection page. (Please go “Setting →

Advance →Motion detection → Setting”) For more details, you can check Chapter

7.8.

54

Use Alarm Buffer:Select Use alarm buffer when you forward the image and video of before and after the alarm detection (pre-alarm, post-alarm). If you do not select it, only the image of the moment of the alarm detection is forwarded. Click Alarm

buffer to display the Alarm buffer setting menu.

Note: You can set the alarm buffer function at alarm buffer page. (Please go “Setting

Advance Alarm buffer Setting”). For more details, you can check

Chapter 7.7.

55

Alarm Input: Select the connected alarm. Sensor input1: The external sensor which is connected to sensor input1 of the alarm input.

Note: You can set the alarm input function at alarm input page. (Please go “Setting →

Advance → Alarm input → Setting”). For more details, you can check Chapter

7.6.

Effective period: Set the period when the periodical sending is effective.

Always: The periodical sending is always effective.

Schedule: You can specify the period when the periodical sending is effective in the

Schedule setting in the other section.

Note: You can set schedule function at schedule page. (Please go “Setting → Advance

→ Schedule → Setting”) For more details, you can check Chapter 7.5.

56

7.1.3 Periodical sending

You can set to send an image file to FTP server periodically by selecting On to send the image file to FTP server linked with setting period.

Image file name: Type the file name of the image sent by SMTP up to 10 alphanumeric characters, - (hyphen) and _ (under score).

Suffix: Select a suffix to be added to the file name sent by SMTP.

None: The name of the sent file will be the Image file name.

Date & time: The date & time suffix is added to the Image file name. The date & time suffix consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2 digits), minute (2 digits) and second (2 digits), and consecutive number (2 digits), thus 14-digit number is added to the file name.

Sequence number: A consecutive number is added to the Image file name.

Sequence number clear: Click Clear and the suffix of the sequence number returns to 1.

Interval: Set the periodical sending is effective interval. Min value is 1 min and Max value is 24 hour.

57

Effective period: Set the period when the periodical sending is effective.

Always: The periodical sending is always effective.

Schedule: You can specify the period when the periodical sending is effective in the

Schedule setting in the other section.

Note: You can set schedule function at schedule page. (Please go “Setting → Advance

→ Schedule → Setting”) For more details, you can check Chapter 7.5.

58

7.2 SMTP

Set the SMTP menu when you want to send an image via e-mail. By using Mail (SMTP) function, you can send a mail with attached image and video which has been shot linked with the external sensor input or with the built-in motion detection function. The image file can also be sent periodically. E-Mail (SMTP) setting menu is composed of three tabs,

General, Alarm sending and Periodical sending.

59

7.2.1 General

Select On when you use the SMTP function. The common setting options are displayed below. Select Off, if you do not wish to use the e-Mail (SMTP) function.

Note :

The Setting of general part will be the same as the setting of IP Notification (Please check

“Setting → Basic → Network → IP Notification”)

SMTP server name: Type the SMTP server name up to 64 characters, or the IP address of the SMTP server.

SMTP Server Port: You can set port number from 1~65535 according to your mail server. The default value is 25.

Security setting: Tick SSL box if the mail server you use has security restriction.

Note:

If you use g-mail as your mail server, you should set 587 as your port number and tick

SSL box.

Authentication: Select the authentication required when you send an email.

Off: Select if no authentication is necessary when an email is sent.

On: When authentication is necessary an e-mail is sent, select one of the authentication methods from the followings.

60

Authentication: Select the authentication required when you send an email.

Off: Select if no authentication is necessary when an email is sent.

On: When authentication is necessary an e-mail is sent, select one of the authentication methods from the followings.

SMTP: Select if SMTP authentication is necessary when an e-mail is sent.

POP before SMTP: Select if POP before SMTP authentication is necessary when an e-mail is sent.

NoteWhen you set to On, be sure to select either or both SMTP or / and POP before SMTP.

POP server name: It is necessary when the POP before SMTP is selected in

Authentication. Type the POP (receiving mail) server name up to 64 characters, or type the IP address of the POP server. This setting is necessary when the SMTP server which sends e-mails performs authentication using the POP user account.

User name, Password: Type the user name and Password of the user who has the mail account. This setting is necessary when the SMTP server which sends e-mails performs authentication.

Recipient e-mail address: Type the recipient e-Mail address up to 64 characters. You can specify up to three recipient E-mail addresses.

Administrator e-mail address: Type the Administrator e-Mail address up to 64 characters. This address is used for reply mail and sending system messages from the

SMTP server.

Subject: Type the subject/title of the e-Mail up to 64 characters. With respect to mail which is sent according to the alarm detection when Alarm sending of the alarm tab is set

61

to On, the characters standing for the sensor type added to the subject.

Message: Type the text of the E-mail up to 384 characters. (A line break is equivalent to 2 characters.)

62

7.2.2 Alarm sending

Set to send the mail with connection to the alarm detection by the external sensor input or by the built-in motion detection function.

Select On to send the image and file to SMTP server linked with the alarm detection.

Alarm sending: Select On to set to send mail with connection to the alarm detection.

File attachment: Set whether an image file is attached to the mail sent or not. When On is selected, the image file made by the settings below is attached. When Off is selected, only the message is sent.

Image file name: Type the file name you want to assign to the image to attach a mail.

You can use up to 10 alphanumeric, - (hyphen) and _ (underscore) for naming.

Suffix: Select a suffix to add to the file name

Date & time: The date & time suffix is added to the Image file name. The date/time suffix consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2 digits), minute (2 digits), second (2 digits), and consecutive number (2 digits), thus 14-digit number is added to the file name.

Sequence number: A consecutive number of 10 digits between 0000000001 and

4294967295 and two fixed digits 00 is added to the Image file name.

Sequence number clear: Click Clear and the suffix of the sequence number returns to 1.

63

Alarm

Motion Detection: Click it on for using Motion Detection function as a sensor. You can set motion detection function at the motion detection function page.

Note: You can set motion detection at motion detection page. (Please go “Setting →

Advance → Motion detection → Setting”) For more details, you can check

Chapter 7.8.

64

Use Alarm Buffer:Select Use alarm buffer when you forward the image and video of before and after the alarm detection (pre-alarm, post-alarm). If you do not select it, only the image of the moment of the alarm detection is forwarded. Click Alarm

buffer to display the Alarm buffer setting menu.

Note: You can set the alarm buffer function at alarm buffer page. (Please go “Setting

Advance Alarm buffer Setting”). For more details, you can check

Chapter 7.7.

Alarm Input: Select the connected alarm. Sensor input1: The external sensor which is connected to sensor input1 of the alarm input.

Note: You can set the alarm input function at alarm input page. (Please go “Setting →

Advance → Alarm input → Setting”). For more details, you can check Chapter

7.6.

65

Effective period: Set the period when the periodical sending is effective.

Always: The periodical sending is always effective.

Schedule: You can specify the period when the periodical sending is effective in the

Schedule setting in the other section.

Note: You can set schedule function at schedule page. (Please go “Setting → Advance

→ Schedule → Setting”) For more details, you can check Chapter 7.5.

66

7.2.3 Periodical sending

You can set to send an image file by SMTP server periodically by selecting On to send the image file by SMTP server linked with setting period.

Image file name: Type the file name of the image sent by SMTP up to 10 alphanumeric characters, - (hyphen) and _ (under score).

Suffix: Select a suffix to be added to the file name sent by SMTP.

None: The name of the sent file will be the Image file name.

Date & time: The date & time suffix is added to the Image file name. The date & time suffix consists of lower two-digits of year (2 digits), month (2 digits), date (2 digits), hour (2 digits), minute (2 digits) and second (2 digits), and consecutive number (2 digits), thus 14-digit number is added to the file name.

Sequence number: A consecutive number is added to the Image file name.

Sequence number clear: Click Clear and the suffix of the sequence number returns to 1.

Interval: Set the periodical sending is effective interval. Min value is 30 min and Max value is 24 hour.

67

Effective period: Set the period when the periodical sending is effective.

Always: The periodical sending is always effective.

Schedule: You can specify the period when the periodical sending is effective in the schedule setting in the other section. Please check “Setting → Basic → Advance →

Schedule → Setting.”

Note: You can set schedule function at schedule page. (Please go “Setting → Advance

→ Schedule → Setting”) For more details, you can check Chapter 7.5.

68

7.3 HTTP event

Use this menu to set up for capturing and sending images to an HTTP server. By using

HTTP client function, you can send the image file and audio file which has been shot and recorded linked with the external sensor input or with the built-in motion detection function to HTTP server. HTTP client setting menu is composed of two tabs, General and Alarm sending.

69

7.3.1 General

HTTP event: Set up the HTTP server URL, port, User ID, Password, and Proxy Server settings.

For example:

URL: 192.168.1.7/cgi-bin/operator/ptzset

Note: The setting of URL should be the same as CGI

70

7.3.2 Alarm sending

Set to send the mail with connection to the alarm detection by the external sensor input or by the built-in motion detection function. Select On to send the image and audio file to HTTP server linked with the alarm detection.

Alarm sending: Select On to set to send mail with connection to the alarm detection.

Alarm

Motion detectionUse alarm buffer Alarm inp ut

Effective period: Set the period when the periodical sending is effective.

Always: The periodical sending is al ways effective.

Sched ule: You can specify the period when the periodical sending is effective in the schedule setting in the other section.

Note:

You can set schedule function at schedule page. (Please go “Setting → Advance →

Schedule → Setting”) For more details, you can check Chapter 7.5.

71

Alarm

Motion Detection: Click it on for using Motion Detection function as a sensor. You can set motion detection function at the motion detection function page.

Note: You can set motion detection at motion detection page. (Please go “Setting →

Advance → Motion detection → Setting”) For more details, you can check Chapter 7.8.

Note Motion Detection works only when the MPEG4 function is On.

Parameter: the parameter of CGI (defined in URL of HTTP → General) is from your target device. For example, move=down.

Message: message will show up in the form of Message = PTZ down. If your target device didn’t support the parameter of message, you can’t see the message. So you can just take the message as a note. For example: PTZ down.

72

Use Alarm Buffer: Select Use alarm buffer when you forward the image / audio of before and after the alarm detection (pre-alarm, post-alarm). If you do not select it, only the image of the moment of the alarm detection is forwarded. Click Alarm buffer to display the Alarm buffer setting menu.

Note:

You can set the alarm buffer function at alarm buffer page. (Please go “Setting →

Advance → Alarm buffer → Setting”) For more details, you can check Chapter 7.7.

Parameter: the parameter of CGI (defined in URL of HTTP→General) is from your target device. For example, move=down.

Message: message will show up in the form of Message = PTZ down. If your target device didn’t support the parameter of message, you can’t see the message. So you can just take the message as a note. For example: PTZ down.

73

Alarm Input: Select the connected alarm. Sensor input1: The external sensor which is connected to sensor input1 of the alarm input.

Note:

You can set the alarm input function at alarm input page. (Please go “Setting → Advance

→ Alarm input → Setting”) For more details, you can check Chapter 7.6.

Parameter: the parameter of CGI (defined in URL of HTTP→General) is from your target device. For example, move=down.

Message: message will show up in the form of Message = PTZ down. If your target device didn’t support the parameter of message, you can’t see the message. So you can just take the message as a note. For example: PTZ down.

74

Effective period: Set the period when the periodical sending is effective.

Always: The periodical sending is always effective.

Schedule: You can specify the period when the periodical sending is effective in the

Schedule setting in the other section.

Note: You can set schedule function at schedule page. (Please go “Setting → Advance

→ Schedule → Setting”) For more details, you can check Chapter 7.5.

75

7.4 Alarm Output

When you click Alarm output on the Advance mode menu, the Alarm output setting menu appears. You can set in this menu to control the alarm out of I / O port on the rear of the device linked to the alarm detection and the timer.

76

7.4.1 Setting

Alarm output: To activate the Alarm output function, select On. When you do not use the Alarm output function, select Off.

Digital output: Select High signal output and Low signal output as your alarm.

Trigger condition: Select the mode of the Alarm output function. You can choose “Alarm” or “Timer”.

Alarm: Controls alarm output by synchronizing with an external sensor input or the built-in activity detection function.

Motion Detection: Click it on for using Motion Detection function as a sensor. You can set motion detection function at the motion detection function page.

77

Note:

You can set motion detection at motion detection page. (Please go “Setting → Advance →

Motion detection → Setting”). For more details, you can check Chapter 7.8.

NoteMotion Detection works only when the Video mode is set to MPEG4 and the

Cropping is set to Off.

Use Alarm Buffer: Select Use alarm buffer when you forward the image / audio of before and after the alarm detection (pre-alarm, post-alarm). If you do not select it, only the image of the moment of the alarm detection is forwarded. Click Alarm

buffer to display the Alarm buffer setting menu.

Note:

You can set the alarm buffer function at alarm buffer page. (Please go “Setting →

Advance → Alarm buffer →Setting ”) For more details, you can check Chapter 7.7.

Alarm Input: Select the connected alarm. Sensor input1: The external sensor which is connected to sensor input1 of the alarm input.

78

Note:

You can set the alarm input function at alarm input page. (Please go “Setting →Advance

→Alarm input → Setting”). For more details, you can check Chapter 7.6.

Alarm duration: There are up to 60 second options to choose for alarm duration interval.

Effective period: Set the period when the periodical sending is effective.

Always: The periodical sending is always effective.

Schedule: You can specify the period when the periodical sending is effective in the

Schedule setting in the other section.

Note:

You can set schedule function at schedule page. (Please go “Setting → Advance →

Schedule → Setting”) For more details, you can check Chapter 7.5.

79

7.5 Schedule

When you click Schedule on the Advance mode menu, the Schedule setting menu appears. This is the same menu as the setting menu which is displayed when you click Schedule to set

Effective period and Schedule in FTP client setting menu, e-Mail (SMTP) setting menu, Alarm out setting menu and so on.

Example: When setting e-Mail (SMTP) (the alarm sending) in the Schedule setting menu.

80

7.5.1 Setting

Schedule Selection: Select the list box to specify the schedule you want to set.

FTP -Alarm

FTP - Periodical

e-Mail (SMTP) -Alarm

e-Mail (SMTP) -Periodical

HTTP event -Alarm

Alarm output- Alarm

Alarm output- Timer

Mon (Monday) to Sun (Sunday): The time period on the right of the checked day is the effective period of the schedule.

Start time, End time: Specify the Start time and the End time.

Use the same time schedule every day: When this is checked, the Start time and End

time set to Mon (Monday) are applied to all days. In this case, the Start time and End time of the other days than Mon (Monday) cannot be input.

81

7.6 Alarm Input

When you click Alarm Input on the Advance mode menu, the Alarm input setting menu appears.

You can set in this menu to control the external alarm input of I / O port on the rear of the device linked to FTP, SMTP, and HTTP sending function.

7.6.1 Setting

Sensor input 1: Cl ick it on for using external sensor which is connected to sensor input1 of the camera I / O port.

Trigger condition: Select High signal output and Low signal output as your alarm.

Camera move: Pull down the window to select the camera preset position.

82

7.7 Alarm buffer

You can set the Pre-alarm image and audio (the image and audio before the alarm detection) and the

Post - alarm image and audio. These can be set when Alarm sending FTP client setting menu or

Image memory setting menu is set to On, and besides when Use alarm buffer is selected.

7.7.1 Setting

Alarm buffer: To activate the Alarm buffer function, select On. The basic setting options are displayed below. When you do not use the Alarm output function, select Off.

Recording capacity

Pre-alarm period: Display the maximum recording capacity of image/audio before the alarm detection.

Post-alarm period: Display the maximum recording capacity of image/audio after the alarm detection.

Recording time: Set the recording time for the Pre-alarm image/audio and Post alarm image/audio.

Pre alarm period: Type it with recording time of the image/audio before the alarm detection.

Post alarm period: Type it with recording time of the image/audio after the alarm detection.

83

7.8 Motion Detection

There are three Motion Detection functions as sensors to set for different detecting zones. Each one has Threshold and Sensitivity inputs which you can adjust to specific zone sequentially.

Motion Detection function can support to FTP, SMTP and Alarm output for capturing and sending images or starting alarm output.

84

7.8.1 Setting

Threshold: It means the extent which the alarm will be triggered.

Sensitivity: It means that how often the sensor will scan the image different. The higher sensitivity it is and the more frequently it scans.

Motion Detection 1: Click it on for using Motion Detection 1 function as a sensor.

You can adjust and move the detecting zone by using mouse.

Motion Detection 2: Click it on for using Motion Detection 2 function as a sensor.

You can adjust and move the detecting zone by using mouse.

Motion Detection 3: Click it on for using Motion Detection 3 function as a sensor.

You can adjust and move the detecting zone by using mouse.

85

7.9 System Log

The System Log function allows users to review any changes and events happened. The system starts logging automatically after started.

7.9.1 Setting

Enable remote log: Enables user to send the log data to a specified log server.

86

CHAPTER 8. APPENDIX

A. Frame-rate and Bitrate Table – Help to set IPCamera with your network environment to access Internet.

Base on your network UPLOAD environment to choose the suitable

Image-Quality setting. For example, if the network environment is ADSL

256Kb/s(upload) / 2Mb/s(download), the most fluent Image-Quality needs to set up under 256 Kb situation.

A.1. NTSC CCD IP Camera

A.1.1. MPEG4 @ 30fps / Kbps

Quality 704*480 352*240 176*120

Excellent 2000 800 200

Detailed

Good

850 250 80

450 150 60

Standard

Medium

A.1.2. MPEG4 / Kbps, fps

350 110 50

250 90 40

Frame-Rate

Setting

Current Bitrate

Current

Frame-Rate

704*480 2048 30 1800 25

704*480 2048 15 2100 16

704*480 1536 30 1500 30

704*480 1536 15 1700 16

704*480 1024 30 1050 30

704*480 1024 15 1100 16

704*480 512 30 520 30

704*480 512 15 650 16

352*240 1536 30 1500 30

352*240 1536 15 1600 16

352*240 1024 30 1100 30

352*240 1024 15 1100 16

352*240 512 30 530 30

352*240 512 15 600 16

176*120 1024 30 1000 30

176*120 1024 15 900 16

176*120 512 30 530 30

176*120 512 15 550 16

176*120 128 30 150 30

176*120 128 15 150 16

87

A.1.3. MJPEG @ 15fps / Kbps

Quality 704*480 352*240 176*120

Excellent 7500 2800 1000

Detailed

Good

Standard

Medium

A.1.4. MJPEG / Kbps, fps

5000 1500 700

3500 1000 500

2000 800 400

1300 500 300

Image-Size

Quality

Setting

Frame-Rate

Setting

704*480 Excellent 15

704*480 Excellent 5

Current Bitrate

Current

Frame-Rate

7500 11

4000 5

704*480 Good 15 3500 13

704*480 Good 5 1500 5

704*480 Medium 15

704*480 Medium 5

352*240 Excellent 15

352*240 Excellent 5

1300 13

550 5

2800 12

1200 5

352*240 Good 15 1000 12

352*240 Good 5 450 5

352*240 Medium 15 500 12

176*120 Medium 5

176*120 Excellent 15

220 5

1000 15

176*120 Excellent 5 400 5

176*120 Good 15 500 15

176*120 Good 5 200 5

176*120 Medium 15 300 15

176*120 Medium 5 100 5

88

A.2. PAL CCD IPCamera

A.2.1. MPEG4 @ 25fps / Kbps

Quality 704*576 352*288 176*144

1800 400 100 Excellent

Detailed

Good

Standard

600 150 50

400 100 40

300 80 30

Medium

A.2.2. MPEG4 / Kbps, fps

200 60 20

Frame-Rate

Setting

Current Bitrate

Current

Frame-Rate

704*576 2048 25 2000 23

704*576 2048 15 2100 16

704*576 1536 25 1600 25

704*576 1536 15 1700 16

704*576 1024 25 1100 25

704*576 1024 15 1200 16

704*576 512 25 550 25

704*576 512 15 650 16

352*288 1536 25 1500 25

352*288 1536 15 1600 16

352*288 1024 25 1100 25

352*288 1024 15 1100 16

352*288 512 25 550 25

352*288 512 15 600 16

176*144 1024 25 1000 25

176*144 1024 15 1000 16

176*144 512 25 550 25

176*144 512 15 600 16

176*144 128 25 150 25

176*144 128 15 150 16

89

A.2.3. MJPEG @ 15fps / Kbps

Quality 704*576 352*288 176*144

Excellent 7800 1700 650

Detailed

Good

Standard

Medium

A.2.4. MJPEG / Kbps, fps

4300 1000 450

2500 650 350

1300 450 250

1000 300 180

Image-Size

Quality

Setting

Frame-Rate

Setting

704*576 Excellent 15

704*576 Excellent 5

Current Bitrate

Current

Frame-Rate

7800 11

4000 5

704*576 Good 15 2500 11

704*576 Good 5 1200 5

704*576 Medium 15

704*576 Medium 5

352*288 Excellent 15

352*288 Excellent 5

1000 11

500 5

1700 11

900 5

352*288 Good 15 650 11

352*288 Good 5 330 5

352*288 Medium 15 300 11

352*288 Medium 5

176*144 Excellent 15

160 5

650 12

176*144 Excellent 5 300 5

176*144 Good 15 350 12

176*144 Good 5 150 5

176*144 Medium 15 180 12

176*144 Medium 5 75 5

90

A.3. CMOS IP Camera

A.3.1. MPEG4 @ 30fps / Kbps

Quality 640*480 320*240 160*120

1000 300 90 Excellent

Detailed

Good

Standard

400 150 50

300 100 30

250 70 25

Medium

A.3.2. MPEG4 / Kbps, fps

250 55 20

Frame-Rate

Setting

Current Bitrate

Current

Frame-Rate

640*480 2048 30 1800 26

640*480 2048 15 2200 16

640*480 1536 30 1500 30

640*480 1536 15 1700 16

640*480 1024 30 1000 30

640*480 1024 15 1000 16

640*480 512 30 500 30

640*480 512 15 600 16

320*240 1536 30 1500 30

320*240 1536 15 1600 16

320*240 1024 30 1000 30

320*240 1024 15 1000 16

320*240 512 30 550 30

320*240 512 15 600 16

160*120 1024 30 950 30

160*120 1024 15 750 16

160*120 512 30 500 30

160*120 512 15 50 16

160*120 128 30 130 30

160*120 128 15 140 16

91

A.3.3. MJPEG @ 15fps / Kbps

Quality 640*480 320*240 160*120

Excellent 4000 1500 600

Detailed

Good

Standard

Medium

A.3.4. MJPEG / Kbps, fps

2400 900 400

1600 650 300

1300 500 240

900 350 170

Image-Size

Quality

Setting

Frame-Rate

Setting

640*480 Excellent 15

640*480 Excellent 5

Current Bitrate

Current

Frame-Rate

4000 13

1600 5

640*480 Good 15 1600 13

640*480 Good 5 650 5

640*480 Medium 15

640*480 Medium 5

320*240 Excellent 15

320*240 Excellent 5

900 14

360 5

1500 13

550 5

320*240 Good 15 650 13

320*240 Good 5 260 5

320*240 Medium 15 350 13

160*120 Medium 5

160*120 Excellent 15

130 5

600 13

160*120 Excellent 5 230 5

160*120 Good 15 300 13

160*120 Good 5 115 5

160*120 Medium 15 170 13

160*120 Medium 5 65 5

92

B. Storage Requirement Table - Help to set Recording Storage System.

Please refer to the following table to find out the capability for recording into your hard disk.

B.1. NTSC CCD IPCamera

B.1.1. MPEG4 Storage Requirement GB / channel / day @ 30fps

Quality 704*480 352*240 176*120

Excellent

Detailed

Good

Standard

Medium

21.1 8.4 2.1

9.0 2.6 0.8

4.7 1.6 0.6

3.7 1.2 0.5

2.6 0.9 0.4

B.1.2. MPEG4 Storage Requirement GB / channel / day @ 15fps

Quality 704*480 352*240 176*120

Excellent 10.5 4.2 1.1

Detailed

Good

Standard

Medium

4.5 1.3 0.4

2.3 0.8 0.3

1.8 0.6 0.2

1.3 0.5 0.2

93

B.1.3. MPEG4 Storage Requirement GB / channel / day

Image-Size Bitrate Setting Frame-Rate Setting

Storage

Requirement

704*480 2048 30 23.0

704*480 2048 15 22.1

704*480 1536 30 18.5

704*480 1536 15 17.9

704*480 1024 30 11.1

704*480 1024 15 11.6

704*480 512 30 5.5

704*480 512 15 6.9

352*240 1536 30 15.8

352*240 1536 15 16.9

352*240 1024 30 11.6

352*240 1024 15 11.6

352*240 512 30 5.6

352*240 512 15 6.3

176*120 1024 30 10.5

176*120 1024 15 9.5

176*120 512 30 5.6

176*120 512 15 5.8

176*120 128 30 1.6

176*120 128 15 1.6

94

B.1.4. MJPEG Storage Requirement GB / channel / day @ 15fps

Quality 704*480 352*240 176*120

Excellent 79.1 29.5 10.5

Detailed

Good

Standard

Medium

52.7

36.9

21.1

13.7

B.1.5. MJPEG Storage Requirement GB / channel / day

15.8

10.5

8.4

5.3

7.4

5.3

4.2

3.2

Image-Size Quality Setting Frame-Rate Setting Current Bitrate

704*480 Excellent 15 79.1

704*480 Excellent 5 42.2

704*480 Good 15 36.9

704*480 Good 5 15.8

704*480 Medium 15

704*480 Medium 5

352*240 Excellent 15

352*240 Excellent 5

13.7

5.8

29.5

12.7

352*240 Good 15 10.5

352*240 Good 5 4.7

352*240 Medium 15

176*120 Medium 5

176*120 Excellent 15

176*120 Excellent 5

5.3

2.3

10.5

4.2

176*120 Good 15 5.3

176*120 Good 5

176*120 Medium 15

176*120 Medium 5

2.1

3.2

1.1

95

B.2. PAL CCD IPCamera

B.2.1. MPEG4 Storage Requirement GB / channel / day @ 30fps

Quality 704*480 352*240 176*120

19.4 4.3 1.1 Excellent

Detailed

Good

Standard

6.5

4.3

3.2

1.6

1.1

0.9

0.5

0.4

0.3

Medium 2.2 0.6

B.2.2. MPEG4 Storage Requirement GB / channel / day @ 15fps

0.2

Quality 704*480 352*240 176*120

Excellent

Detailed

Good

Standard

Medium

9.7

3.2

2.2

1.6

1.1

2.2

0.8

0.5

0.4

0.3

0.5

0.3

0.2

0.2

0.1

96

B.2.3. MPEG4 Storage Requirement GB / channel / day

Image-Size Bitrate Setting Frame-Rate Setting

Storage

Requirement

704*480 2048 30 21.6

704*480 2048 15 22.7

704*480 1536 30 17.3

704*480 1536 15 18.4

704*480 1024 30 11.9

704*480 1024 15 13.0

704*480 512 30 5.9

704*480 512 15 7.0

352*240 1536 30 16.2

352*240 1536 15 17.3

352*240 1024 30 11.9

352*240 1024 15 11.9

352*240 512 30 5.9

352*240 512 15 6.5

176*120 1024 30 10.8

176*120 1024 15 10.8

176*120 512 30 5.9

176*120 512 15 6.5

176*120 128 30 1.6

176*120 128 15 1.6

97

B.2.4. MJPEG Storage Requirement GB / channel / day @ 15fps

Quality 704*480 352*240 176*120

Excellent 84.2 18.4 7.0

Detailed

Good

Standard

Medium

46.4

27.0

14.0

10.8

B.2.5. MJPEG Storage Requirement GB / channel / day

10.8

7.0

4.9

3.2

4.9

3.8

2.7

1.9

Image-Size Quality Setting Frame-Rate Setting Current Bitrate

704*480 Excellent 15 84.2

704*480 Excellent 5 43.2

704*480 Good 15 27.0

704*480 Good 5 13.0

704*480 Medium 15

704*480 Medium 5

352*240 Excellent 15

352*240 Excellent 5

10.8

5.4

18.4

9.7

352*240 Good 15 7.0

352*240 Good 5 3.6

352*240 Medium 15

176*120 Medium 5

176*120 Excellent 15

176*120 Excellent 5

3.2

1.7

7.0

3.2

176*120 Good 15 3.8

176*120 Good 5

176*120 Medium 15

176*120 Medium 5

1.6

1.9

0.8

98

B.3. CMOS IPCamera

B.3.1. MPEG4 Storage Requirement GB / channel / day @ 30fps

Quality 640*480 320*240 160*120

10.5 3.2 0.9 Excellent

Detailed

Good

Standard

4.2

3.2

2.6

1.6

1.1

0.7

0.5

0.3

0.3

Medium 2.6 0.6

B.3.2. MPEG4 Storage Requirement GB / channel / day @ 15fps

0.2

Quality 640*480 320*240 160*120

Excellent

Detailed

5.3

2.1

1.6

0.8

0.4

0.3

Good

Standard

Medium

B.3.3. MPEG4 Storage Requirement GB / channel / day

Image-Size

1.6

1.3

1.3

0.6

0.4

0.3

0.2

0.1

0.1

Bitrate Setting Frame-Rate Setting Current Bitrate

640*480 2048 30 23.0

640*480 2048 15 22.2

640*480 1536 30 18.5

640*480 1536 15 17.9

640*480 1024 30 10.5

640*480 1024 15 10.5

640*480 512 30 5.3

640*480 512 15 6.3

320*240 1536 30 15.8

320*240 1536 15 16.9

320*240 1024 30 10.5

320*240 1024 15 10.5

320*240 512 30 5.8

320*240 512 15 6.3

160*120 1024 30 10.0

160*120 1024 15 7.9

160*120 512 30 5.3

160*120 512 15 0.5

160*120 128 30 1.4

160*120 128 15 1.5

99

B.3.4. MJPEG Storage Requirement GB / channel / day @ 15fps

Quality 640*480 320*240 160*120

Excellent 42.2 15.8 6.3

Detailed

Good

Standard

Medium

25.3

16.9

13.7

9.5

B.3.5. MJPEG Storage Requirement GB / channel / day

9.5

6.9

5.3

3.7

4.2

3.2

2.5

1.8

Image-Size Quality Setting Frame-Rate Setting Current Bitrate

640*480 Excellent 15 42.2

640*480 Excellent 5 16.9

640*480 Good 15 16.9

640*480 Good 5 6.9

640*480 Medium 15

640*480 Medium 5

320*240 Excellent 15

320*240 Excellent 5

9.5

3.8

15.8

5.8

320*240 Good 15 6.9

320*240 Good 5 2.7

320*240 Medium 15

160*120 Medium 5

160*120 Excellent 15

160*120 Excellent 5

3.7

1.4

6.3

2.4

160*120 Good 15 3.2

160*120 Good 5

160*120 Medium 15

160*120 Medium 5

1.2

1.8

0.7

100

C. System Requirement &

D1 Performance of 16 Channel IP Camera

Equipment Configuration

Software: MainConsole Version 2.6.4 Professional

CPU: AMD Athlon 64*2 @3600+MHz

Memory:

Ethernet:

Hard Disk:

2048 MB (2 x 1024 DDR2-SDRAM )

VIA Rhine II Fast Ethernet Adapter

ST3250620A (250 GB)

Graphic card: ATI Technologies Inc EAX1600 Series

Operating System: Windows XP Professional SP2 x64

Results from Test with a Resolution of 704×480 CCD IPCamera

704x480 Quality Frame Rate CPU Load Bandwidth

16 IP camera Excellent 30 95% 15~20 Mbps

Results from Test with a Resolution of 640×480 CMOS IPCamera

640x480 Quality Frame Rate CPU Load Bandwidth

16 IP camera Excellent 30 95% 10~15 Mbps

101

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals