Pride Mobility JAZZY 1113 ATS Owner`s manual

JAZZY 1113 ATS
1-800-800-8586 (US) 1-888-570-1113 (Canada)
SAFETY
GUIDELINES
WARNING! An authorized Pride Provider or a qualified technician must perform the initial
setup of this power chair and must perform all of the procedures in this manual.
The symbols below are used throughout this owner's manual and on the power chair to identify warnings and important
information. It is very important for you to read them and understand them completely.
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designated
procedures can cause either personal injury, component damage, or malfunction. On the
product, this icon is represented as a black symbol on a yellow triangle with a black border.
MANDATORY! These actions should be performed as specified. Failure to perform mandatory
actions can cause personal injury and/or equipment damage. On the product, this icon is
represented as a white symbol on a blue dot with a white border.
PROHIBITED! These actions are prohibited. These actions should not be performed at any
time or in any circumstances. Performing a prohibited action can cause personal injury and/or
equipment damage. On the product, this icon is represented as a black symbol with a red
circle and red slash.
Quick Reference Information
Authorized Pride Provider:_______________________________________________________________
Address:____________________________________________________________________________
Phone Number:_______________________________________________________________________
Purchase Date:________________________________________________________________________
NOTE: This owner’s manual is compiled from the latest specifications and product information available at the time of publication. We reserve the right to make changes as they become necessary. Any
changes to our products may cause slight variations between the illustrations and explanations in this
manual and the product you have purchased. The latest/current version of this manual is available on our
website.
Copyright © 2011
Pride Mobility Products Corp.
INFMANU1801/Rev M/August 2011
C O N T E N T S
I.
INTRODUCTION ................................................................................................................................. 4
II.
SAFETY ................................................................................................................................................. 6
III. YOUR POWER CHAIR .................................................................................................................... 14
IV.
DISASSEMBLY AND ASSEMBLY ............................................................................................. 19
V.
COMFORT ADJUSTMENTS........................................................................................................ 25
VI. BATTERIES AND CHARGING .................................................................................................... 32
VII. CARE AND MAINTENANCE ........................................................................................................ 36
Jazzy 1113 ATS
www.pridemobility.com
3
I.
INTRODUCTION
SAFETY
WELCOME to Pride Mobility Products Corporation (Pride). The power chair you have purchased combines state-ofthe-art components with safety, comfort, and styling in mind. We are confident that these design features will provide you
with the conveniences you expect during your daily activities. Once you understand how to safely operate and care for
your power chair, it should give you years of trouble free operation and service.
Read and follow all instructions, warnings, and notes in this manual before attempting to operate your power chair for the
first time. In addition, your safety depends upon you, as well as your provider, caretaker, or healthcare professional in
using good judgement.
If there is any information in this manual which you do not understand, or if you require additional assistance for setup or
operation, please contact your authorized Pride Provider. Failure to follow the instructions in this manual and those
located on your power chair can lead to personal injury and/or damage to the power chair, including voiding the
warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove or
render inoperable or unsafe any guards, shields, or other safety features of this product; fail, refuse, or neglect to install any
retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product.
SHIPPING AND DELIVERY
Before using your power chair, make sure your delivery is complete as some components may be individually packaged.
If you do not receive a complete delivery, please contact your authorized Pride Provider immediately. Where damage has
occurred during transport, either to the packaging or content, please contact the delivery company responsible.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about the safety
and reliability of your new power chair, and about the service you received from your authorized Pride Provider.
Please notify us of any change of address, so we can keep you apprised of important information about safety, new
products, and new options that can increase your ability to use and enjoy your power chair. Please feel free to contact us
at the address below:
USA:
Pride Mobility Products Corporation
Attn.: Customer Care Department
182 Susquehanna Avenue
Exeter, PA 18643-2694
customercare@pridemobility.com
800-424-8205
Canada:
Pride Mobility Products Company
380 Vansickle Road Unit 350
St. Catharines, Ontario L2R 6P7
1-888-570-1113
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us and
we will be glad to send you a new one immediately.
4
www.pridemobility.com
Jazzy 1113 ATS
I.
INTRODUCTION
PRIDE OWNERS CLUB
As an owner of a Pride product, you are encouraged to enroll in the Pride Owners Club. Complete and return your
enclosed product registration card or visit Pride’s web site at www.pridemobility.com.
From our home page, select “Owners Club” to enter a page dedicated to current and potential Pride product owners. You
will gain access to interviews, stories, recreation ideas, daily living tips, product and funding information, and interactive
message boards. These message boards invite you to communicate with other Pride customers as well as Pride representatives who are available to assist you with any questions or concerns you may have.
Jazzy 1113 ATS
www.pridemobility.com
5
I I .
S A F E T Y
SAFETY
MANDATORY! Do not operate your new power chair for the first time without completely reading
and understanding this owner’s manual.
Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive
variety of products to best fit the individual needs of the power chair user. Please be aware that the final selection and
purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user, who is
capable of making such a decision, and his/her healthcare professional (i.e., medical doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power chair
to the user and has assisted the prescribing healthcare professional and/or the authorized Pride Provider in the instruction
process for the use of the product.
There are certain situations, including some medical conditions, where the power chair user will need to practice operating
the power chair in the presence of a trained attendant. A trained attendant can be defined as a family member or care
professional specially trained in assisting a power chair user in various daily living activities.
As you begin using your power chair during daily activities, you will probably encounter situations in which you will need
some practice. Simply take your time and you will soon be in full and confident control as you maneuver through doorways,
on and off of elevators, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help you become accustomed to operating the
power chair safely.
Modifications
Pride has designed and engineered your power chair to provide maximum mobility and utility. A wide range of accessories
is available from your authorized Pride Provider to further customize your power chair to better suit your needs and/or
preferences. However, under no circumstances should you modify, add, remove, or disable any feature, part, or function
of your power chair.
WARNING! Do not modify your power chair in any way not authorized by Pride. Do not use
accessories if they have not been tested or approved for Pride products.
Pre-Ride Safety Check
Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check before
each use to make sure your power chair operates smoothly and safely.
Perform the following inspections prior to using your power chair:
! Check for proper tire inflation. Maintain 35 psi (2.4 bar) in each tire if equipped with pneumatic tires.
! Check all electrical connections. Make sure they are tight and not corroded.
! Check all controller connections to the power base. Make sure they are secured properly.
! Check the brakes. See VII. “Care and Maintenance.”
! Check battery charge. See VI. “Batteries and Charging.”
NOTE: If you discover a problem, contact your authorized Pride Provider for assistance.
6
www.pridemobility.com
Jazzy 1113 ATS
II.
SAFETY
Weight Limitations
Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.
MANDATORY! Stay within the specified weight capacity of your power chair. Exceeding the weight
capacity voids your warranty. Pride will not be held responsible for injuries and/or property damage
resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your power chair. Carrying passengers on your power
chair may affect the center of gravity, resulting in a tip or a fall.
Tire Inflation
If your power chair is equipped with pneumatic tires, you should check or have the air pressure checked at least once a
week. Proper inflation pressures will prolong the life of your tires and help ensure the smooth operation of your power chair.
WARNING! It is important that 35 psi (2.4 bar) tire pressure be maintained in pneumatic tires at
all times. Do not underinflate or overinflate your tires. Low pressure may result in loss of control,
and overinflated tires may burst. Failure to maintain 35 psi (2.4 bar) tire pressure in pneumatic
tires at all times may result in tire and/or wheel failure.
WARNING! Inflate your power chair drive tires from a regulated air source with an available pressure
gauge. Inflating your tires from an unregulated air source could overinflate them, resulting in a
burst tire.
Incline Information
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access. Some ramps
may have turning switchbacks (180-degree turns) that require you to have good cornering skills on your power chair.
! Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
! Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power chair’s rear
wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.
! When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to ensure a safely
controlled descent.
! Avoid sudden stops and starts.
When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and then accelerate
cautiously. When driving down an incline, set your power chair to the slowest setting and drive in the forward direction
only. If your power chair starts to move down the incline faster than you anticipated or desired, allow it to come to a
complete stop by releasing the joystick, then push the joystick forward slightly to ensure a safely controlled descent.
WARNING! When on any sort of an incline or decline, never place the power chair in freewheel
mode while seated on it or standing next to it.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the incline.
Drive your power chair straight up the incline. This greatly reduces the possibility of a tip or a fall.
Always exercise extreme caution when negotiating an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas covered
with snow, ice, cut grass, or wet leaves).
WARNING! Never travel down an incline backwards. Doing so may cause the power chair to tip.
Always exercise extreme caution when negotiating an incline.
WARNING! If your power chair is equipped with a reclining seatback, do not attempt to negotiate
inclines with the seat in a reclined position. Do not attempt to negotiate obstacles with the seat
in a reclined position unless an attendant is present to help stabilize the chair. Failure to heed
could result in the power chair tipping over.
Jazzy 1113 ATS
www.pridemobility.com
7
II.
SAFETY
WARNING! Even though your power chair is capable of climbing slopes greater than those illustrated
in figure 1, do not, under any circumstances, exceed the incline guidelines or any other
specifications presented in this manual. Doing so could cause instability in your power chair.
In compliance with the Americans with Disabilities Act of 1990, all handicap public access ramps are required to have a
maximum slope of 5° (8.7%). Therefore, Pride recommends that the maximum slope of an incline you attempt to safely
ascend or descend on your power chair does not exceed 5° (8.7%). See figure 1.
WARNING! Any attempt to climb or descend a slope steeper than 5° (8.7%) may put your power
chair in an unstable position and cause it to tip
5 (8.7%)
Figure 1. Maximum Safe Angle (Ascending and Descending)
Freewheel Mode
Your power chair is equipped with a manual freewheel lever system to allow for manual maneuverability by a trained attendant.
For more information about how to place your power chair into and out of freewheel mode, see III. “Your Power Chair.”
WARNING! Do not use your power chair in freewheel mode without an attendant present.
WARNING! Do not attempt to personally place your power chair in freewheel mode while seated
on it. Ask an attendant for assistance if necessary.
WARNING! Do not place your power chair in freewheel mode while on an incline or decline. The
chair could roll uncontrollably on its own.
Braking Information
Your power chair is equipped with two powerful brake systems:
1. Regenerative — uses electricity to rapidly slow the vehicle when the joystick returns to the center/stop position.
2. Disc Park Brake — activates mechanically after regenerative braking slows the vehicle to near stop, or when power
is removed from the system for any reason.
Cornering Information
While your power chair is equipped with rear caster wheels and front anti-tip wheels, excessively high cornering speeds can
still create the possibility of tipping. Factors which affect the possibility of tipping include, but are not limited to: cornering
speed, steering angle (how sharply you are turning), uneven road surfaces, inclined road surfaces, riding from an area of low
traction to an area of high traction (such as passing from a grassy area to a paved area – especially at high speed while turning),
and abrupt directional changes. High cornering speeds are not recommended. If you feel that you may tip over in a corner,
reduce your speed and steering angle (i.e., lessen the sharpness of the turn) to prevent your power chair from tipping.
WARNING! When cornering sharply, reduce your speed and maintain a stable center of gravity.
This greatly reduces the possibility of a tip or fall. Always exercise common sense when cornering.
8
www.pridemobility.com
Jazzy 1113 ATS
II.
SAFETY
Outdoor Driving Surfaces
Your power chair is designed to provide optimum stability under normal driving conditions—dry, level surfaces composed
of concrete, blacktop, or asphalt. However, Pride recognizes that there will be times when you will encounter other surface
types. For this reason, your power chair is designed to perform admirably on packed soil, grass, and gravel. Feel free to
use your power chair safely on lawns and in park areas.
! Reduce your power chair’s speed when driving on uneven terrain and/or soft surfaces.
! Avoid tall grass that can entangle the running gear.
! Avoid loosely packed gravel and sand.
! If you feel unsure about a driving surface, avoid that surface.
Inclement Weather Precautions
Exposure of your power chair to inclement weather conditions should be avoided whenever possible. If suddenly caught
up in rain, snow, severe cold or heat while operating your power chair, proceed to shelter at the earliest opportunity.
Thoroughly dry your power chair before storing, charging, or operating your power chair.
PROHIBITED! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery surfaces
can have an adverse effect on the electrical system. Maintain and store your power chair in a dry
and clean condition.
WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of upholstered
and non-upholstered items on the power chair, possibly resulting in skin irritation. Exercise caution
when using the power chair in extremely hot or cold conditions or when exposing your power
chair to direct sunlight for prolonged periods of time.
Stationary Obstacles (Steps, Curbs, etc.)
Proceed with extreme caution when driving near raised surfaces, unprotected ledges and/or drop-offs (curbs, porches,
stairs, etc.). Be sure your power chair is traveling perpendicular to any curb you may be required to navigate. See figure 2.
WARNING! Do not attempt to have your power chair climb or descend an obstacle that is higher
than 2 in. (5 cm) unless you have the assistance of an attendant.
WARNING! Do not attempt to have your power chair proceed backwards down any step, curb, or
other obstacle. This may cause the power chair to tip.
CURB
CURB
Figure 2. Correct Curb Approach
Jazzy 1113 ATS
Figure 3. Incorrect Curb Approach
www.pridemobility.com
9
II.
SAFETY
Stairs and Escalators
Power chairs are not designed to travel up or down stairs or escalators. Always use an elevator.
WARNING! Never use your power chair to negotiate steps or escalators.
Doors
! Determine if the door opens toward or away from you.
! Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently and slowly
backwards to pull the door open.
Elevators
Modern elevators have a door edge safety mechanism that, when pushed, reopens the elevator door(s).
! If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge or allow the
rubber door edge to contact the power chair and the door will reopen.
! Use care that pocketbooks, packages, or power chair accessories do not become caught in elevator doors.
Lift/Elevation Products
If you will be traveling with your power chair, you may find it necessary to use a lift/elevation product to aid in transportation.
Pride recommends that you closely review the instructions, specifications, and safety information set forth by the manufacturer
of the lift/elevation product before using that product.
WARNING! Never sit on your power chair when it is being used in connection with any type of lift/
elevation product. Your power chair was not designed with such use in mind and any damage or
injury incurred from such use is not the responsibility of Pride.
Motor Vehicle Transport
Pride recommends that you do not remain seated in your power chair while traveling in a motor vehicle. The power chair
should be stowed in the trunk of a car or in the back of a truck or van with the batteries removed and properly secured.
WARNING! Do not sit on your power chair while it is in a moving vehicle.
WARNING! Always be sure your power chair and its batteries are properly secured when it is being
transported. Batteries should be secured in an upright position and protective caps should be
installed on the battery terminals. Batteries should not be transported with any flammable or
combustible items.
Positioning Belts
Your authorized Pride Provider, therapist(s), and other healthcare professionals are responsible for determining your
requirement for a positioning belt in order to operate your power chair safely.
WARNING! If you require a positioning belt to safely operate your power chair, make sure it is
fastened securely in order to reduce the possibility of a fall from the power chair.
WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle. Nor is
your power chair suitable for use as a seat in any vehicle. Anyone traveling in a vehicle should be
properly belted into seats approved by the vehicle manufacturer.
10
www.pridemobility.com
Jazzy 1113 ATS
II.
SAFETY
Batteries
In addition to following the warnings below, be sure to comply with all other battery handling information. For more
information about your power chair’s batteries, see VI. “Batteries and Charging.”
MANDATORY! Battery posts, terminals, and related accessories contain lead and lead compounds.
Wear goggles and gloves when handling batteries and wash hands after handling.
WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that
much weight, be sure to get help. Use proper lifting techniques and avoid lifting beyond your
capacity.
WARNING! Always protect the batteries from freezing and never charge a frozen battery. Charging
a frozen battery may result in damage to the battery.
WARNING! Connect your battery harnesses in the proper manner. RED (+) cables must be connected
to positive (+) battery terminals/posts. BLACK (-) cables must be connected to negative (-) battery
terminals/posts. Protective caps should be installed over all battery terminals. REPLACE cables
immediately if damaged.
Removable Parts
WARNING! Do not attempt to lift or move a power chair by any of its removable parts, including the
armrests, seat, foot riggings, controller, and shrouds.
Preventing Unintended Movement
WARNING! If you anticipate being seated in a stationary position for an extended period of
time, turn off the power. This will prevent unexpected motion from inadvertent joystick contact.
This will also eliminate the possibility of unintended chair movement from electromagnetic
(EM) sources.
Reaching and Bending
Never reach, lean, or bend while driving your power chair. If it is absolutely necessary to reach, lean, or bend while seated
on your power chair, it is important to maintain a stable center of gravity and keep the power chair from tipping. Pride
recommends that the power chair user determine his/her personal limitations and practice bending and reaching in the
presence of a qualified healthcare professional.
WARNING! Keep your hands away from the tires when driving. Be aware that loose fitting clothing
can become caught in drive tires.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the floor by
reaching down between your knees or if you have to reach over the back of the seat. Movements
such as these may change your center of gravity and the weight distribution of the power chair.
This may cause your power chair to tip.
Jazzy 1113 ATS
www.pridemobility.com
11
II.
SAFETY
Transfers
Transferring onto and off of your power chair requires a good
sense of balance. Always have an attendant or healthcare professional present while learning to properly transfer yourself.
To eliminate the possibility of injury, Pride recommends that
you or a trained attendant perform the following tasks before
attempting a transfer:
! Turn off the power to the controller.
! Ensure your power chair is not in freewheel mode. See
III. “Your Power Chair.”
! Turn the caster wheels toward the transfer destination to
improve power chair stability during transfer.
! Make sure both armrests are flipped up or removed from
your power chair.
! Flip up the foot platform or move the leg rests aside; this
will help to keep your feet from getting caught on the foot
rigging during the transfer.
! Reduce the distance between your power chair and the
object you are transferring onto.
WARNING! Before transfer ring, position
yourself as far back as possible in the power
chair seat to prevent the power chair from
tipping forward during transfer.
Figure 4. Ideal Transfer Position
WARNING! Avoid putting all of your weight on the power chair armrests and do not use the armrests
for weight bearing purposes, such as transfers. Such use may cause the power chair to tip,
resulting in a fall from the power chair.
WARNING! Avoid putting all of your weight on the foot riggings. Such use may cause the power
chair to tip.
Prescription Drugs/Physical Limitations
Users must exercise care and common sense when operating a power chair. This includes awareness of safety issues when
taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter medication or
if you have certain physical limitations. Some medications and limitations may impair your ability
to operate your power chair in a safe manner.
Alcohol/Smoking
The power chair user must exercise care and common sense when operating his/her power chair. This includes awareness
of safety issues while under the influence of alcohol or while smoking.
WARNING! Do not operate your power chair while you are under the influence of alcohol, as this
may impair your ability to operate your power chair in a safe manner.
12
www.pridemobility.com
Jazzy 1113 ATS
II.
SAFETY
WARNING! Pride strongly recommends that you do not smoke cigarettes while seated in your
power chair, although the power chair has passed the necessary testing requirements for cigarette
smoking. You must adhere to the following safety guidelines if you decide to smoke cigarettes
while seated in your power chair.
! Do not leave lit cigarettes unattended.
! Keep ashtrays a safe distance from the seat cushions.
! Always make sure cigarettes are completely extinguished before disposal.
Electromagnetic and Radio Frequency Interference (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves can
have an adverse affect on the performance of electrically-powered mobility vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile two-way
radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless computer links,
microwave signals, paging transmitters, and medium-range mobile transceivers used by emergency vehicles. In some
cases, these waves can cause unintended movement or damage to the control system. Every electrically-powered mobility
vehicle has an immunity (or resistance) to EMI. The higher the immunity level, the greater the protection against EMI. This
product has been tested and has passed at an immunity level of 20 V/m.
WARNING! Be aware that cell phones, two-way radios, laptops, and other types of radio transmitters
may cause unintended movement of your electrically-powered mobility vehicle due to EMI.
Exercise caution when using any of these items while operating your mobility vehicle and avoid
coming into close proximity of radio and TV stations.
WARNING! The addition of accessories or components to the electrically-powered mobility vehicle
can increase the susceptibility of the vehicle to EMI. Do not modify your power chair in any way
not authorized by Pride.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance of other
electrical devices located nearby, such as alarm systems.
NOTE: For further information on EMI/RFI, go to the Resource Center on www.pridemobility.com. If
unintended motion or brake release occurs, turn your power chair off as soon as it is safe to do so. Call
Pride at 800-424-8205 to report the incident.
Jazzy 1113 ATS
www.pridemobility.com
13
III.
YOUR
POWER
CHAIR
THE JAZZY 1113 ATS
Your power chair has two main assemblies: the seat and the power base. See figure 5. Typically, the seating system
includes the armrests, the seatback, the seat base, and the controller. The power base assembly includes two drive wheels,
two anti-tip wheels, two rear caster wheels, a body shroud, four frame assemblies (located under the body shroud), two
battery boxes, and the electrical connectors. See figures 5, 6, and 7.
SEAT BACK
ARMRESTS
SEAT
ASSEMBLY
CONTROLLER
SEAT BASE
BODY SHROUD
FREEWHEEL LEVERS
POWER
BASE
ASSEMBLY
CASTER WHEEL
FOOT RIGGING
(FOOT PLATFORM SHOWN)
DRIVE WHEEL
ANTI-TIP WHEELS
Figure 5. The Jazzy 1113 ATS
14
www.pridemobility.com
Jazzy 1113 ATS
III.
YOUR
POWER
CHAIR
Specifications
Suspension:
Drive Wheels:
Caster Wheels:
Anti-Tip Wheels:
Maximum Speed:¹
Range:¹
Brakes:
Ground Clearance:²
Turning Radius:²
Overall Size:²
Drivetrain:
Batteries:³
Battery Charger:
Weight Capacity:
Component Weights:
1
Active-Trac Suspension
10 in., (25.4 cm) center-mounted, pneumatic or solid available
8 in. (20.32 cm), solid, rear articulating
6 in. (15.24 cm), solid, front mounted
Up to 4 mph (6.44 km)
Up to 25 miles (40.23 km/h)
“Intelligent Braking,” electronic regenerative, disc park brake
2.5 in. (6.35 cm)
18.5 in. (47 cm)
Length: 36.5 in. (92.71 cm)
Width: 23 in. (58.42 cm) assembled
Two motor, mid-wheel
Two 12-volt, U-1 batteries
4-amp, Onboard (standard)
8-amp, Off-board
300 lbs. (136 kg); 160 lbs. (72.5 kg ) with Synergy Manual Tilt
Seat: 33 lbs. (15 kg)
Foot Platform: 8.5 lbs. (3.86 kg)
Front Battery and Case: 26 lbs. (11.79 kg); U-1 Battery: 24.5 lbs. (11.11 kg)
Rear Battery and Case: 26 lbs. (11.79 kg); U-1 Battery: 24.5 lbs. (11.11 kg)
Battery Well Frame: 13.5 lbs. (6.12 kg)
Front Frame: 2.5 lbs. (1.13 kg)
Right Frame Assembly: 38 lbs. (17.24 kg)
Left Frame Assembly: 38 lbs. (17.24 kg)
²
Varies with base model, user weight, terrain type, battery amp hour rating (Ah), battery charge, battery condition,
motors, controller type, tire type, and tire condition.
Due to manufacturing tolerances and continued product improvement, this specification can be subject to a variance of
(+ or – ) 3%.
AGM or Gel-Cell type required. See VI. “Batteries and Charging.”
³
NOTE: All specifications subject to change without notice.
Jazzy 1113 ATS
www.pridemobility.com
15
III.
YOUR
POWER
CHAIR
Electrical Components
The electrical components consist of the controller, the batteries, and the motors. The batteries, motors, and controller
power module (if equipped) are located on the power base assembly. The controller is located on the seat assembly.
Connectivity between the controller and the motors, batteries, and the battery charger is provided by one or more wiring
harnesses. See figures 6 and 7.
Controller Connector: This is where the controller connects to the power base. Each controller uses a different type of
cable. Regardless of which type of controller is used, the cable must be secured to the seat assembly and not allowed to
drag on the floor.
Ammeter: This displays the charger’s current output in amps.
Main Circuit Breaker: This is a safety feature built into your power chair. When the batteries and the motors are heavily
strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage to the motors and the electronics. If
the circuit trips, allow the power chair to “rest” for approximately one minute. Then, push in the circuit breaker button, turn
on the controller, and continue normal operation. If the main circuit breaker continues to trip repeatedly, contact your
authorized Pride Provider.
Charger Power Cord Receptacle: This is where the charger power cord plugs in when the batteries need to be recharged.
Battery Connectors (Quick-Connectors): These provide a connection between the battery boxes and the electronics
tray.
Motor Connectors: These provide a connection between the motors and the electronics tray.
AMMETER
CONTROLLER CONNECTOR
(VSI SHOWN)
MAIN CIRCUIT BREAKER
CHARGER POWER CORD
RECEPTACLE
Figure 6. Power Base Rear View - Electronics Tray
16
www.pridemobility.com
Jazzy 1113 ATS
III.
YOUR
BATTERY CONNECTORS
(QUICK-CONNECTORS)
POWER
CHAIR
REAR BATTERY BOX
MOTOR CONNECTOR
SEAT TOWERS
MOTOR CONNECTOR
FRONT
BATTERY
BOX
Figure 7. Power Base Top View
Manual Freewheel Levers
For convenience, your power chair is equipped with two manual freewheel levers—one for each motor. See figures 8 and
9. These levers allow you to disengage the drive motors from the gearboxes and maneuver the chair manually. This is called
freewheel mode.
WARNING! Do not use the power chair while the drive motors are disengaged! Do not disengage
the drive motors when the power chair is on an incline or decline, as the unit could roll on its own.
Only engage the freewheel mode when on a level surface.
WARNING! It is important to remember that when your power chair is in freewheel mode, the
braking system is disengaged.
WARNING! Do not use the freewheel lever handles as tie-down points to secure this product.
Jazzy 1113 ATS
www.pridemobility.com
17
III.
YOUR
POWER
CHAIR
To engage or disengage the drive motors:
1. Locate the manual freewheel levers at the front of the chair.
2. Push the levers down to engage the drive motors (drive mode). See figure 8.
3. Pull the levers upward to disengage the drive motors (freewheel mode). See figure 9.
If a lever is difficult to move in either direction, rock your power chair back and forth slightly. The lever should then move
to the desired position.
MANUAL
FREEWHEEL LEVER
MANUAL
FREEWHEEL LEVER
Figure 8. Drive Mode (Drive Engaged)
Figure 9. Freewheel Mode (Drive Disengaged)
Active-Trac System
Your power chair is equipped with an Active-Trac System
(ATS). See figure 10. ATS is a suspension system designed
to make your power chair traverse different types of terrain
and obstacles while maintaining smooth operation. With ATS,
the front anti-tip wheels work in conjunction with the motor
suspension to help you maneuver over obstacles.
ATS SPRING
As the front anti-tip wheels come in contact with an obstacle,
the front anti-tip wheel assembly is drawn upward. At the
same time, the motors are forced downward. This allows
the motors to push the power chair over an obstacle and
limits the possibility of your power chair becoming “hung up”
on the obstacle.
ATS also helps in day-to-day operating conditions. For
instance, when you release the joystick, your power chair
begins to slow down. As the chair slows down, the front
anti-tip wheels will automatically drop toward the ground.
This will reduce the forward tip that is typically encountered
with center-wheel drive chairs.
18
www.pridemobility.com
Figure 10. ATS System
Jazzy 1113 ATS
I V. D I S A S S E M B LY A N D A S S E M B LY
INITIAL ASSEMBLY
Your power chair may require some assembly either before initial use or after transportation. It may also require disassembly
to make some comfort adjustments.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be
replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon
insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores
or through your authorized Pride Provider.
Seat Installation
It may be necessary to install the seat either prior to initial operation or after transporting your power chair. Most seats are attached
to the power base with the Universal Mounting System (UMS). The UMS consists of universal parts that may be attached to any
medium-back or high-back seat, regardless of seat width or seat depth. The two main components are aluminum extrusions
mounted to the seat base. These extrusions attach to a pair of trapeze bars that are mounted to the power base.
WARNING! Do not pick up the seat frame by the armrests. They are free to pivot, and you may lose
control of the seat if they do so.
To install the seat:
1. Set the trapeze bars to the desired height. To change the trapeze bar height, see V. “Comfort Adjustments.”
2. Tilt the seat back, and slide the rear extrusion onto the rear trapeze bar. See figure 11.
3. Lower the front extrusion onto the front trapeze bar until the seat locks into place.
4. Flip the seat latch safety down. See figure 12.
WARNING! Make sure the seat latch safety is flipped down before using your power chair.
5. Install the controller into one of the armrests. See V. “Comfort Adjustments.”
SEAT LATCH SAFETY
REAR
TRAPEZE
BAR
FRONT TRAPEZE BAR
REAR EXTRUSION
FRONT EXTRUSION
Figure 11. Universal Mounting System
Jazzy 1113 ATS
Figure 12. Seat Latch Safety
www.pridemobility.com
19
I V. D I S A S S E M B L Y A N D A S S E M B LY
6. Route the controller cable so that it cannot be pinched in the seat hinge and plug the cable into the controller connector
on the electronics tray.
MANDATORY! Prevent controller harness damage! Use correct tie-down points for controller
harness.
7. Secure the controller cable to the armrest receiver with one or more wire ties.
DISASSEMBLY
Your power chair disassembles into eight easily transportable component assemblies with no tools required. See figures 13
and 14. Place the power chair in an area where there is ample space to work and move around the unit—3 feet (1 meter)
of clearance on all sides. Make sure the unit is powered off before disassembling the chair.
WARNING! Even though no tools are required to disassemble or assemble your power chair, you
should take care not to place your hands or fingers on the areas of the component assemblies
where they may be pinched, as the assemblies “snap” together or “snap” apart.
WARNING! Some power chair components are heavy. You may need assistance to lift or carry
them. Please refer to the specifications table for specific component weights before you
disassemble the power chair.
NOTE: During both the disassembly and the assembly of your power chair, you may find it helpful to engage
the drive motors to secure the unit from rolling. See III. “Your Power Chair.”
LEFT POWER BASE
FRAME ASSEMBLY
BATTERY WELL
FRAME
FRONT FRAME
BATTERY BOXES
RIGHT POWER BASE
FRAME ASSEMBLY
FOOT PLATFORM
Figure 13. Jazzy 1113 ATS Component Assemblies
20
www.pridemobility.com
Jazzy 1113 ATS
I V. D I S A S S E M B LY A N D A S S E M B LY
BALL DETENT
PIN
SEAT TOWER
Figure 14. Seat Installation/Removal
Jazzy 1113 ATS
www.pridemobility.com
21
I V. D I S A S S E M B L Y A N D A S S E M B LY
To disassemble your power chair:
1. Disconnect the controller harness from its connector on the
electronics tray. See figure 6. You may need to pull firmly and
gently wiggle the harness to remove it from the connector.
2. Remove the ball detent pin from each seat tower. See figure 14.
3. Pull up on the seat. You may find it necessary to wiggle the
frame gently from side to side to free it from the seat towers.
WARNING! Do not pick up the seat frame by the
armrests. They are free to pivot, and you may lose
control of the seat if they do so.
Figure 15. Foot Platform Removal
4. Remove the foot platform by lifting it up, then pulling it out away
from the chair. See figure 15.
5. Disconnect both battery connectors and both motor connectors.
See figure 7.
6. Lift and remove each battery box. See figure 16.
7. Squeeze together the latch release levers that hang vertically
down from the crossbar at the rear of the battery well frame.
See figure 17.
8. Lift up the rear end of the battery well frame. Pull it to the rear
of the chair to release the front slots from the locating pins on
the front frame bottom bar.
9. Stand behind your power chair and grasp one of the power
base frame assembly handles. See figure 18.
10. Press the chrome latch release lever toward the center of the
frame and hold it.
11. Push the frame assembly outward and pull up on the front frame
until the latching mechanism releases.
12. Keep pulling upward until the locating pin on the bottom of the
front frame releases from its slot in the power base frame
assembly.
13. Carefully let the power base frame assembly tilt to a resting
position.
14. Repeat steps 9-13 for the other power base frame assembly.
22
www.pridemobility.com
Figure 16. Removing Battery Boxes
Jazzy 1113 ATS
I V. D I S A S S E M B L Y A N D A S S E M B L Y
ASSEMBLY
To assemble the power chair:
1. Place the three frame assemblies next to each other as shown in
figure 19.
2. Grasp the front frame and fit the notch on the front frame bottom
bar onto the locating pin on the lower section of the power base
frame assembly. See figure 20.
WARNING! The front frame should be positioned
with the two semicircular notches in the vertical
bar facing forward.
3. Pivot the front frame top bar toward the power base frame
assembly and push the front frame top bar onto the locking
mechanism until the two assemblies snap securely into place.
See figure 18.
4. Repeat steps 1-3 for the other power base frame assembly.
WARNING! Make certain that the front frame is
snapped securely to both the right frame
assembly and to the left frame assembly.
5. Hold the battery well frame so that the bottom of the well hangs
downward.
6. Position the notches on the front of the battery well frame onto
the locating pins on the front frame bottom bar. See figure 20.
7. Fit the notch on either side of the rear of the battery well frame
onto the locating pin on each power base frame assembly.
8. Make certain that the locking mechanisms snap securely into
place.
9. Place the front battery box into the front end of the battery well
frame.
Figure 17. Removing Battery Well Frame
NOTE: Make certain that the connectors are facing toward
the center of the power chair.
10. Place the rear battery box into the back end of the battery well
frame. Make certain that none of the wiring harnesses or cables
are pinched between the battery or the motor controller box
and the frame.
11. Connect the battery boxes. Use the battery connection label
located on the back of the electronics tray for reference.
12. Reconnect the left and right motor connectors. Be certain to
match the left connector to the left motor and the right connector
to the right motor. The connectors are labeled left and right.
Figure 18. Power Base Frame Removal/
Installation
Jazzy 1113 ATS
www.pridemobility.com
23
I V. D I S A S S E M B L Y A N D A S S E M B LY
13. Pick up the seat by the frame and set the seat onto the towers
so the holes align with those on the seat towers.
14. Insert the ball detent pin into each seat tower.
15. Match the two tabs at the back of the foot platform mounting
bracket with the two semicircular notches in the vertical bar of
the front frame.
16. Push the tabs through the matching notches.
17. Slide the foot platform down into place.
18. Reconnect the controller harness to its connector on the
electronics tray. See figure 6.
WARNING! Do not place the controller harness
so that it can be pinched in the seat frame or
the power base frame.
Figure 19. Frame Assembly Position
LOCATING PINS
BATTERY WELL FRAME
Figure 20. Connect Battery Well Frame
24
www.pridemobility.com
Jazzy 1113 ATS
V.
COMFORT
ADJUSTMENTS
COMFORT ADJUSTMENTS
After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase
your comfort, such as seat height and angle, armrest angle, foot platform height and angle, and controller position.
NOTE: If your power chair is equipped with a Synergy Seating System or Synergy TRU-Balance Power
Positioning System, refer to the information in separate manuals. If your power chair is equipped with a
contour seating system, refer to the following information.
WARNING! If your power chair was configured by your authorized Pride Provider, please consult your
healthcare professional before changing the seat position or making any adjustment. Some
adjustments may degrade your power chair’s performance and safety by changing its center of
gravity.
WARNING! Some power chair components are heavy. You may need assistance to lift or carry
them. Please refer to the specifications table for specific component weights before you
disassemble the power chair.
WARNING! Remove the occupant from the power chair before making any adjustments.
You may need the following to make comfort adjustments:
! metric/standard socket set and ratchet
! adjustable wrench
! metric/standard hex key set
! thread lock
Seat Height and Seat Angle Adjustment
You can change the seat height by either raising or lowering the four seat towers.
To change the seat height:
1. Turn off the power to the controller.
2. Disconnect the controller harness connector from the electronics tray.
3. Remove the ball detent pins that attach the trapeze bars to the seat towers. See
figure 14.
4. Remove the seat.
5. Remove the battery harnesses.
6. Remove the battery boxes.
7. Remove the ball detent pin from each seat tower as shown in figure 21.
8. Raise or lower each seat tower to the desired position.
9. Install the ball detent pin into each seat tower.
10. Reinstall the battery boxes.
11. Reinstall the battery harnesses.
12. Reinstall the seat and secure the trapeze bars.
13. Connect the controller harness connector to the electronics tray
BALL DETENT PIN
Figure 21. Seat Tower
To change the seat angle:
Raise or lower only one set of seat towers (front or rear).
Jazzy 1113 ATS
www.pridemobility.com
25
V.
COMFORT
ADJUSTMENTS
Seat Position
You can move the seat forward or rearward by changing the
extrusion mounting position.
To
1.
2.
3.
4.
5.
change the position:
Turn off the power to the controller.
Disconnect the controller from the electronics tray.
Remove the seat from the power base.
Remove both extrusions from the bottom of the seat.
Reposition the extrusions on a different set of mounting
holes. You must move both extrusions the same number of
holes either forward or backward. See figure 22.
6. Fasten the extrusions back onto the bottom of the seat.
7. Reinstall the seat.
8. Connect the controller to the electronics tray.
Manual Recline Seatback Adjustment
If your power chair is equipped with an optional reclining seat,
you can adjust the seatback angle with the seatback release
lever. The lever is located on the right side of the seat base.
To adjust the seatback angle:
1. Pull up on the seatback release lever.
2. Move the seatback down or up to the desired position.
3. Release the lever.
Headrest Adjustment
If your power chair is equipped with the optional high-back
seat with headrest, you can adjust the headrest height.
To adjust the headrest height:
1. Push in the headrest release button.
2. Move the headrest up or down to the desired position.
Seatback Angle Adjustment
If your power chair is equipped with an adjustable seatback,
you can adjust it to four (4) different angles: 90°, 102°, 105°,
or 107°.
To adjust the seatback angle:
1. Remove the seatback angle adjustment screws from each
seat hinge. See figure 23.
2. Set the seatback at the desired angle.
3. Reinstall the adjusting screws to each seat hinge and tighten.
26
www.pridemobility.com
Figure 22. Seat Mounting Holes
JAM NUT
ARMREST
ANGLE
ADJUSTMENT
SCREW
ARMREST
HEIGHT
ADJUSTING
SETSCREWS
SEATBACK
ANGLE
ADJUSTMENT
SCREW
ARMREST KNOB
Figure 23. Seatback and Armrest Adjustments
Jazzy 1113 ATS
V.
COMFORT
ADJUSTMENTS
Armrest Width Adjustment
You can change each armrest’s width independently of the other.
NOTE: Changing the armrest width may increase the overall width of your power chair.
To change the armrest width:
1. Locate the two armrest knobs on each side of the armrest receiver bracket. See figure 23.
2. Loosen the knobs.
3. Slide the armrests in or out to the desired width.
4. Tighten the knobs.
Armrest Height Adjustment
To change the armrest height:
1. Loosen the two setscrews located on the armrest receiver. See figure 23.
2. Raise or lower the armrest to the desired height.
3. Tighten the setscrews to secure the armrest.
Armrest Angle Adjustment
To change the armrest angle:
1. Lift the armrest straight up so that it is perpendicular to the floor.
2. Loosen the jam nut. See figure 23.
3. Turn the adjustment screw to raise the front of the armrest or to lower the front of the armrest.
5. Tighten the jam nut to lock the adjustment screw into place.
Controller Position
You can move the controller in toward or out away from the
armrest, or change the position of the controller for either
left-hand or right-hand use.
WARNING! Do not place the controller cable
so that it can be pinched in the seat frame or
the power base frame.
To extend the controller:
1. Flip up the armrest so it is perpendicular to the floor.
2. Loosen the setscrew on the controller bracket. See figure 14.
3. Slide the controller into or out of the armrest to the desired position.
To change the controller position:
1. Turn off the power to the controller.
2. Unplug the controller connector(s) from the power base.
3. Cut any wire ties that attach the controller cable to the
armrest.
4. Flip up the armrest and loosen the setscrew. See
figure 24.
Jazzy 1113 ATS
SETSCREW
Figure 24. Underside of Armrest
www.pridemobility.com
27
V.
COMFORT
ADJUSTMENTS
5. Slide the controller out of the armrest and place it in the
other armrest.
6. Tighten the setscrew.
7. Use a wire tie to secure the controller harness to the
armrest.
8. Plug the controller connector(s) into the power base.
FOOT PLATFORM BRACKET
NOTE: If your power chair is equipped with a Synergy
Seating System or Synergy Tru-Balance Power
Positioning System, refer to the controller adjustment
information provided in separate manuals.
Foot Platform Height Adjustment
The foot platform height is easily adjusted to different
heights in 1-2-in. (2.54-5.08 cm) increments.
Figure 25. Foot Platform Height Adjustment
To raise or lower the foot platform:
1. Remove the hardware from the foot platform bracket. See
figure 25.
2. Raise or lower the foot platform to the desired height.
3. Reinstall the hardware into the foot platform bracket and
tighten.
Foot Platform Angle Adjustment
You can adjust the angle of the foot platform with a hex key and
wrench.
To adjust the foot platform angle:
1. Flip up the foot platform and locate the setscrew. See
figure 26.
2. Loosen the nut and turn the setscrew to raise the front
of the foot platform or to lower the front of the foot
platform.
3. Tighten the nut to secure the setscrew.
Swing-Away Footrests
Swing-Away Footrests (SFRs) enable you to rotate the footrests to the side before you transfer onto or off of your power
chair. See figure 27.
SETSCREW
Figure 26. Foot Platform Angle Adjustment
SFR RELEASE LEVER
FOOTREST
EXTENSION
ADJUSTMENT
SCREWS
To rotate the SFRs:
1. Push in the release lever.
2. Rotate the SFRs.
Figure 27. Swing-away Footrest Adjustment
28
www.pridemobility.com
Jazzy 1113 ATS
V.
COMFORT
ADJUSTMENTS
To adjust the SFR length:
1. Remove the two adjustment screws from the back of
each footrest extension.
2. Slide the footrest up or down to the desired length.
3. Reinstall the two adjustment screws.
Elevating Leg Rests
Elevating Leg Rests (ELRs) offer an infinite range of adjustment for the leg angle and a footrest adjustment range
of 12–19 in. (30.48-48.26 cm). See figure 28.
To rotate the ELRs:
1. Push in release lever A.
2. Rotate the ELRs.
RELEASE LEVER A
RELEASE LEVER B
LEG REST
EXTENSION
ADJUSTMENT
SCREWS
Figure 28. Elevating Leg Rests
To adjust the ELR angle:
1. Push down release lever B.
2. Move the leg rest to the desired angle.
LEG REST
HANGER
To adjust the ELR length:
1. Remove the two adjustment screws from the side of
each leg rest extension.
2. Slide the leg rest up or down to the desired length.
3. Reinstall the two adjustment screws.
ADJUSTMENT BOLT
LEG REST
EXTENSION
ADJUSTMENT SCREWS
Heavy Duty Drop-in Leg Rests (Optional)
You can adjust the forward/back position, as well as the
length of the heavy duty drop-in leg rests. See figure 29.
To adjust the forward/back position:
1. Remove the adjustment bolt from each side rail.
2. Move the leg rest hanger in or out to the desired position.
3. Align the adjustment holes in the leg rest hanger with
those in the side rail.
4. Reinstall each adjustment bolt to secure the leg rest
hangers.
Figure 29. Heavy Duty Drop-In Leg Rests
To adjust the leg rest length:
1. Remove the adjustment screws from the leg rest
extension.
2. Slide the leg rest up or down to the desired length.
3. Align the adjustment holes in the leg rest extension and
reinstall the adjustment screws.
Jazzy 1113 ATS
www.pridemobility.com
29
V.
COMFORT
ADJUSTMENTS
Multi-Axis Foot Plates
The multi-axis foot plate assembly can be installed on either
a swing-away footrest or an elevating leg rest. The multiaxis foot plate has four adjustments: leg rest length (A),
position (B), tilt (C), and angle (D). See figure 30.
To change leg rest length (A):
1. Remove the hardware.
2. Move the leg rest to the desired position.
3. Reinstall the hardware.
A
B
To change foot plate position (B):
1. Remove the hardware.
2. Move the foot plate to the desired position.
3. Reinstall the hardware.
C
D
To change foot plate tilt (C):
1. Loosen the hardware.
2. Tilt the foot plate to the desired position.
3. Tighten the hardware.
A
To change foot plate angle (D):
1. Turn the setscrew clockwise to decrease the angle.
2. Turn the setscrew counterclockwise to increase the
angle.
B
C
D
SETSCREW
LOCATION
Figure 30. Multi-Axis Foot Plate
30
www.pridemobility.com
Jazzy 1113 ATS
V.
COMFORT
ADJUSTMENTS
Anti-Tip Wheel Adjustment
The anti-tip wheels are designed to give your power chair increased stability on rough surfaces. The anti-tip wheels are
preset for smooth surfaces or indoor use only. If you plan on using your power chair on rough surfaces, it may be
necessary to adjust the anti-tip wheels to better suit your needs. The anti-tip wheels may need adjustment if either of the
following occur:
! When coming to a stop, your power chair tips forward excessively.
! The anti-tip wheels constantly rub the ground.
WARNING! Consult your authorized Pride Provider before attempting to change the anti-tip height!
Changing the anti-tip wheel height affects handling under deceleration!
WARNING! The higher you raise the anti-tip wheels, the more tendency you increase your power chair’s
tendency to tilt forward decelerating. You can compensate for this by having your authorized Pride
Provider make a small adjustment to the pre-programmed deceleration setting in the controller or by
moving the seat assembly farther to the back of your power chair.
PROHIBITED! Do not remove the anti-tip wheels.
NOTE: Each drive tire must have at least 35 psi (2.4 bar) of air pressure in order for the anti-tip wheels to be
properly adjusted.
To adjust the anti-tips:
1. Make sure the power chair is in drive mode.
2. Loosen the nut and bolt that fasten the anti-tip spring to the anti-tip arm. See figure 31.
3. Remove the anti-tip adjustment bolt.
4. Raise or lower the anti-tip wheel in 1/4-in. (0.64 cm) increments.
5. Replace the hardware into the appropriate hole and tighten.
NUT AND BOLT
ANTI-TIP ADJUSTMENT BOLT
ANTI-TIP WHEEL
Figure 31. Anti-Tip Adjustment
Jazzy 1113 ATS
www.pridemobility.com
31
VI.
BATTERIES
AND
CHARGING
BATTERIES AND CHARGING
Your power chair uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free.
Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a
longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable.
Automotive batteries are not designed to handle a long, deep discharge, and also are unsafe for use in power chairs.
MANDATORY! Batter y posts, ter minals and related accessories contain lead and lead
compounds. Wear goggles and gloves when handling batteries and wash hands after handling.
WARNING! Contact your authorized Pride Provider if you have any questions regarding the batteries
in your power chair.
WARNING! Do not use batteries that exceed the recommended type and amp-hour capacity.
Do not use batteries with different amp-hour capacities. Refer to the specifications table in this
manual and in the manual supplied with the batter y charger for recommended type and
capacities.
Charging the Batteries
The battery charger is essential in providing long life for your power chair batteries. It is designed to optimize your power
chair’s performance by charging the batteries safely, quickly, and easily. The battery charging system consists of the battery
charger, the charger circuit fuse, and the ammeter (onboard chargers only). The ammeter indicates the rate of charge
necessary to fully recharge the batteries. It is also a good indication of whether or not the charger is working. The ammeter
and the charger are only functional when the charger power cord is plugged into an electrical outlet.
PROHIBITED! Removal of grounding prong can create electrical hazard. If necessary, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access.
PROHIBITED! Never use an extension cord to plug in your battery charger. Plug the charger
directly into a properly wired standard electrical outlet.
PROHIBITED! Do not allow unsupervised children to play near the power chair while the batteries
are charging. Pride recommends that you do not charge the batteries while the power chair is
occupied.
MANDATORY! Read the battery charging instructions in this manual and in the manual supplied
with the battery charger before charging the batteries.
WARNING! You must recharge your power chair’s batteries with the supplied onboard charger or
off-board charger. Do not use an automotive-type battery charger.
WARNING! Do not expose the off-board battery charger to rain or other sources of moisture
unless it has been tested for outdoor use. Refer to the manual supplied with the battery charger
for more information.
WARNING! Inspect the battery charger, wiring, and connectors for damage before each use.
Contact your authorized Pride Provider if damage is found.
WARNING! Do not attempt to open the battery charger case. If the battery charger does not
appear to be working correctly, contact your authorized Pride Provider.
WARNING! If the battery charger is equipped with cooling slots, then do not attempt to insert
objects through these slots.
32
www.pridemobility.com
Jazzy 1113 ATS
VI.
BATTERIES
AND
CHARGING
WARNING! If your battery charger has not been tested and approved for outdoor use, then do not
expose it to adverse or extreme weather conditions. If the battery charger is exposed to adverse
or extreme weather conditions, then it must be allowed to adjust to the difference in environmental
conditions before use indoors. Refer to the manual supplied with the battery charger for more
information.
To charge the batteries using the onboard charger:
1. Position the rear of your power chair close to a standard electrical outlet.
2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power
Chair.”
3. Plug the charger power cord into the charger power cord receptacle on the power base, then into the electrical outlet.
NOTE: The power chair incorporates an inhibit function that disables the power chair when the charger is
plugged into an electrical outlet.
4. We recommend you charge the batteries for 8 to 14 hours. As the batteries charge, the ammeter needle slowly drops to 0.
NOTE: The ammeter indicates how much charge is needed to fully charge the batteries. As the batteries
charge, the ammeter needle slowly drops to 0. When the batteries are fully charged, the needle vibrates on or
about the 0 mark on the ammeter.
5. When your power chair’s batteries are fully charged, disconnect the charger power cord, wind up the cord, and store
it in a safe place.
To charge the batteries using the optional off-board charger:
1. Position the front of your power chair next to a standard electrical outlet.
2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power
Chair.”
3. Plug the off-board charger into the off-board charger/programming socket on the controller.
4. Plug the off-board charger into the electrical outlet.
NOTE: If it is a Pride off-board charger, then there are two lights in it. The red light indicates that power to
the off-board charger is on. The green light indicates that the batteries are fully charged. If it is not a Pride offboard charger, then follow the instructions supplied by the manufacturer.
5. When the batteries are fully charged, unplug the off-board charger from the electrical outlet and then from the controller.
Battery Break-in
To break in new batteries for maximum efficiency:
1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak performance
level.
2. Operate your power chair throughout the house and yard. Move slowly at first, and do not travel too far until you
become accustomed to the controls and break in the batteries.
3. Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries will now
perform at over 90% of their potential.
4. After four or five charging cycles, the batteries will top off at 100% charge and last for an extended period.
Jazzy 1113 ATS
www.pridemobility.com
33
VI.
BATTERIES
AND
CHARGING
Frequently Asked Questions (FAQs)
How does the charger work?
The battery charger takes the standard electrical outlet voltage of 120 VAC (alternating current) and converts it to 24
VDC (direct current). The power chair batteries use direct current to run your power chair. When the battery voltage is
low, the charger works harder to charge the battery. As the battery voltage approaches full charge, the charger doesn’t
work as hard to complete the charging cycle. When the battery is fully charged, the amperage from the charger is nearly at
zero. This is how the charger maintains a charge but does not overcharge the battery.
Can I use a different battery charger?
You should use the charger supplied with the power chair. It is the safest, most efficient tool to charge the batteries. We do
not recommend using other types of chargers (e.g., an automotive battery charger).
NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zero
voltage. If this happens, call your authorized Pride Provider for assistance.
How often must I charge the batteries?
Many factors come into play when deciding how often to charge the batteries. You may use your power chair all day on a
daily basis or you may not use it for weeks at a time.
! Daily Use
If you use your power chair on a daily basis, charge the batteries as soon as you are finished using your power chair.
Your power chair will be ready each morning to give you a full day’s service. It is recommended that you charge the
batteries 8 to 14 hours after daily use.
! Infrequent Use
If you use your power chair infrequently (once a week or less), you should charge the batteries at least once per week
for 12 to 14 hours.
NOTE: Keep your batteries fully charged and avoid deeply discharging your batteries. Refer to the manual
supplied with the battery charger for charging instructions.
How can I get maximum range or distance per charge?
Rarely do you have an ideal driving situation such as smooth, flat, hard terrain with no wind, hills, or curves. More often you
are presented with hills, sidewalk cracks, uneven and loosely packed surfaces, curves, and wind. All of these factors will
affect the distance or running time per battery charge. Below are a few suggestions for obtaining the maximum range per
charge:
! Always charge the batteries fully prior to your trip.
! Plan your trip in advance to avoid inclines if possible.
! Limit baggage weight to essential items.
! Try to maintain an even speed and avoid stop-and-go driving.
What type of batteries should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deep-cycle
batteries that are similar in performance.
WARNING! Corrosive chemicals contained in batteries. Use only AGM or Gel-Cell batteries to
reduce the risk of leakage or explosive conditions.
34
www.pridemobility.com
Jazzy 1113 ATS
VI.
BATTERIES
AND
CHARGING
Why do my new batteries seem weak?
Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cadmium (nicads),
or in other common battery types. Deep-cycle batteries are specifically designed to provide power, drain down their
charge, and then accept a relatively quick recharge. AGM and Gel-Cell batteries should be charged as often as possible.
They do not have a “memory” like nickel-cadmium batteries.
We work closely with our battery manufacturer to provide a battery that best suits your power chair’s specific demands.
Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge. During shipping, the batteries encounter
temperature extremes that may influence initial performance. Heat robs the charge from the battery, and cold slows the
power available and extends the time needed to recharge the battery (just as with a car battery).
It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature. More
importantly, it will take a few “charging cycles” (a partial drain— then a full recharge) to establish the critical chemical
balance that is essential to the battery’s peak performance and long life. It will be well worth it to take the time to break in
your battery properly.
How can I ensure maximum battery life?
A fully charged deep-cycle battery will provide reliable performance and extended battery life. Keep your power chair’s
batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently charged, or
stored without a full charge may be permanently damaged, causing unreliable power chair operation and limited battery
life.
NOTE: The useful life of a battery is quite often a reflection of the care it receives.
How should I store my power chair and its batteries?
If you do not use your power chair regularly, we recommend maintaining battery vitality by charging the batteries at least
once per week.
If you do not plan on using your power chair for an extended period, fully charge the batteries prior to storage. Disconnect
the battery harnesses and store the power chair in a warm, dry environment. Avoid temperature extremes, such as freezing
and excessively hot conditions, and never attempt to charge a frozen battery. A cold or frozen battery should be warmed
for several days prior to recharging.
What about public transportation?
AGM and Gel-Cell batteries are designed for application in power chairs and other mobility vehicles. These batteries are
Federal Aviation Administration (FAA) approved, allowing safe transportation on aircraft, buses, and trains, as there is no
danger of spillage or leakage. We suggest you contact the carrier’s ticket counter in advance to determine that carrier’s
specific requirements.
What about shipping?
If you wish to use a freight company to ship your power chair to your final destination, repack your power chair in the
original shipping container and ship the batteries in separate boxes.
Jazzy 1113 ATS
www.pridemobility.com
35
VII.
CARE
AND
MAINTENANCE
CARE AND MAINTENANCE
Your Jazzy 1113 ATS is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks.
You can perform some of these checks, but others require assistance from your authorized Pride Provider. Preventive
maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help ensure that
your power chair gives you years of trouble-free operation. If you have any doubt as to your power chair’s care or
operation, contact your authorized Pride Provider.
WARNING! Do not service the power chair when the seat is occupied.
Your power chair, like most electrical equipment, is susceptible to damage from the elements. Avoid damp areas of any kind.
WARNING! Direct or prolonged exposure to water or dampness could cause the power chair to
malfunction electronically and mechanically. Water can cause electrical components to corrode
and the chair’s frame to rust. Power chairs should be examined periodically for signs of corrosion
caused by water exposure, bodily fluids exposure, or incontinence. Damaged components should
be replaced or treated immediately.
Should your power chair come in contact with water:
1. Dry your power chair as thoroughly as possible with a towel.
2. Allow your power chair to sit in a warm, dry place for 12 hours to allow unseen water to evaporate.
3. Check the joystick operation and the brakes before using your power chair again.
4. If any inconsistencies are found, take your power chair to your authorized Pride Provider. Power chairs that are frequently exposed to sources of water, such as incontinence, should be inspected often for corrosion and electronic
components may need to be replaced frequently.
Temperature
! Some of the parts of your power chair are susceptible to extreme changes in temperature. Always keep your power
chair between the temperatures of 18° F (-8°C) and 122° F (50°C).
! In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze depends on a
number of factors, such as battery charge, usage, and composition of the batteries (e.g., AGM or Gel-Cell).
! Temperatures above 122° F (50°C) may cause your power chair to operate at a reduced speed. This reduced speed
is a safety feature built into the controller that helps prevent damage to the motor and other electrical components.
General Guidelines
! Avoid knocking or bumping the controller, especially the joystick.
! Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture.
! Keep the controller clean.
! Check all connectors to ensure that they are all tight and secured properly.
! Make sure the pneumatic tires are inflated to 35 psi (2.4 bar) if equipped with pneumatic tires..
WARNING! Make sure your tires are inflated to 35 psi (2.4 bar). Do not underinflate or overinflate
your tires. Low pressure may result in loss of control, and overinflated tires may burst. Overinflating
tires can cause them to explode.
WARNING! Do not use a high pressure hose to inflate your tires.
! Use a rubber conditioner on the tire sidewalls to help preserve them.
WARNING! Never use a rubber conditioner on the tread area of the tires; doing so may make the
tires slippery and cause your power chair to skid.
36
www.pridemobility.com
Jazzy 1113 ATS
VII.
CARE
AND
MAINTENANCE
! All wheel bearings are prelubricated and sealed. They require no subsequent lubrication.
! The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it retain
its high-gloss appearance.
! Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the
battery boxes and battery well frame with the battery terminals facing inward toward each other. Refer to the battery
wiring label for the correct wiring layout.
WARNING! Even though the power chair has passed the necessary testing requirements for ingress
of liquids, you should keep electrical connections away from sources of dampness, including
direct exposure to water or bodily fluids and incontinence. Check electrical components frequently
for signs of corrosion and replace as necessary.
Daily Checks
! With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the neutral
position when you release it. Check the rubber boot around the base of the joystick for damage. Visually inspect the boot.
Do not handle or try to repair it. See your authorized Pride Provider if there is a problem.
! Visually inspect the controller communications cable. Make sure that it is not frayed, cut, or has any wires exposed.
See your authorized Pride Provider if there is a problem.
! Check for flat spots on solid tires. Flat spots could adversely affect stability.
Weekly Checks
! Disconnect and inspect the controller and the charger harness from the electronics tray. Look for corrosion. Contact
your authorized Pride Provider if necessary.
! Ensure that all parts of the controller system are securely fastened to your power chair. Do not overtighten any screws.
! Check for proper tire inflation. There should be 35 psi (2.4 bar) in each tire. If a tire does not hold air, see your
authorized Pride Provider for replacement of the tube.
! Check the brakes. This test should be carried out on a level surface with at least 3 feet of clearance around your power chair.
To check the brakes:
1. Turn on the controller and turn down the speed level of your power chair.
2. After one second, check the battery condition meter. Make sure that it remains on.
3. Slowly push the joystick forward until you hear the electric brakes click. Immediately release the joystick. You must be
able to hear each electrical brake operating within a few seconds of joystick movement. Repeat this test three times,
pushing the joystick backward, then left, and then right.
Monthly Checks
! Check that the anti-tip wheels do not rub the ground when you operate the power chair. Adjust them as necessary.
! Check for extreme wear on the anti-tip wheels. Replace them as necessary.
! Check for drive tire wear. See your authorized Pride Provider for repair.
! Check the caster wheels for wear. Replace them as necessary.
! Check the caster forks for damage or fluttering which indicates that they may need to be adjusted or have the bearings
replaced. See your authorized Pride Provider for repair.
! Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc.
Yearly Checks
Take your power chair to your authorized Pride Provider for yearly maintenance, especially if you use your power chair on
a regular basis. This helps ensure that your power chair is functioning properly and helps prevent future complications.
Jazzy 1113 ATS
www.pridemobility.com
37
VII.
CARE
AND
MAINTENANCE
Storage
Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries
from the power chair. See VI. “Batteries and Charging.”
WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be
damaged.
Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures, or stored without
a full charge may be permanently damaged, causing unreliable performance and limited service life. It is recommended that
you charge the batteries periodically throughout periods of prolonged storage to ensure proper performance.
You may wish to place several boards under the frame of your power chair to raise it off of the ground during periods of
prolonged storage. This takes the weight off the tires and reduces the possibility of flat spots developing on the areas of the
tires contacting the ground.
Disposal of Your Power Chair
Your power chair must be disposed of according to applicable local and national statutory regulations. Contact your local
waste disposal agency or authorized Pride Provider for information on proper disposal of power chair packaging, metal
frame components, plastic components, electronics, and batteries.
Cleaning and Disinfection
! Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your power chair. Avoid using
products that may scratch the surface of your power chair.
! If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on your
product before application.
WARNING! Follow all safety instructions for the proper use of the disinfectant and/or cleaning
agent before applying it to your product. Failure to comply may result in skin irritation or premature
deterioration of upholstery and/or power chair finishes.
WARNING! Never hose off your power chair or place it in direct contact with water. Your power chair
has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a damp cloth.
WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become
slippery or dry out and crack. Use soapy water and dry the seat thoroughly.
Wheel Replacement
If you have pneumatic tires and you have a flat tire, replace the tube. If your chair is equipped with a solid tire insert, then
you must replace the whole wheel assembly. Replacement tires, tubes, and wheel assemblies are readily available through
your authorized Pride Provider.
WARNING! The wheels on your power chair should only be serviced or replaced by an authorized
Pride Provider or a qualified technician.
WARNING! Be sure that the power to the controller is turned off and the power chair is not in
freewheel mode before performing this procedure.
WARNING! When changing a tire, remove only the center lug nut and washer, then remove the
wheel. If any further disassembly is required, deflate the tire completely or it may explode.
38
www.pridemobility.com
Jazzy 1113 ATS
VII.
CARE
AND
MAINTENANCE
TIRE
AXLE KEY
WHEEL HUB
TUBE
DRIVE WHEEL
NUT
FRONT
RIM HALF
AXLE SLOT
REAR RIM
HALF
NUTS
DRIVE WHEEL WASHER
Figure 32. Drive Wheel
WASHERS
Figure 33. Drive Wheel Disassembled
Follow these easy steps for a quick and safe repair for both pneumatic and solid tires:
1. Turn off the power to the controller.
2. Set the power chair up on blocks.
3. If you are changing a pneumatic tire, completely deflate it before removing the wheel.
4. Remove the drive wheel nut and washer from the axle. See figure 32.
5. Pull the wheel off the axle.
6. Remove the nuts and washers from the wheel hub and separate the front and rear rim. See figure 33.
7. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is a solid
tire.
8. Reassemble the rims and reinstall the nuts and washers to the wheel hub.
9. Slide the wheel back onto the axle. Make sure the key is in the axle slot.
10. Reinstall the drive wheel nut and washer onto the axle and tighten.
11. Inflate the pneumatic tire to 35 psi (2.4 bar).
12. Remove the power chair from the blocks.
Battery Replacement
A battery wiring diagram is printed on a decal located on the battery well frame. Refer to the specifications table for correct
battery specifications.
MANDATORY Battery posts, terminals, and related accessories contain lead and lead compounds.
Wear goggles and gloves when handling batteries and wash hands after handling.
WARNING! The batteries on your power chair should only be serviced or replaced by an authorized
Pride Provider or a qualified technician.
WARNING! Do not replace battery when seat is occupied.
WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that
much weight, be sure to get help. Use proper lifting techniques and avoid lifting beyond your
capacity.
WARNING! Do not mix or match new and old batteries. If you encounter a situation where one
battery needs to be replaced, then replace both batteries. Refer to specifications table in this
manual and the manual supplied with the battery charger for recommended type and capacities.
Jazzy 1113 ATS
www.pridemobility.com
39
VII.
CARE
AND
MAINTENANCE
To replace the batteries:
1. Turn off the power to the controller.
2. Make sure that the power chair is in drive mode. See III. “Your Power
Chair.”
3. Unplug the controller connector(s) from the power base.
4. Remove the seat.
5. Unplug the battery quick-connectors from the power base.
6. Unfasten the straps, remove the battery boxes from the battery well and
open the lids.
7. Remove the old batteries.
8. Disconnect the wiring harnesses from the batteries.
9. Connect the wiring harness to the new batteries. See figure 34.
WARNING! Make sure you tighten the fasteners so that the
connections are secure.
Figure 34. Battery Wiring Diagram
10. Place the new batteries into the battery boxes and replace the lids.
11. Place the battery boxes into the battery well on the power base and refasten the straps.
12. Plug in the quick-connectors.
13. Reinstall the seat.
14. Plug the controller connector(s) into the power base.
15. Charge the batteries.
When to See Your Authorized Pride Provider for Service
The following symptoms could indicate a serious problem with your power chair. If necessary, contact your authorized
Pride Provider. When calling, have the model number, serial number, nature of the problem, and the error code if available.
! Motor noise
! Frayed harnesses
! Cracked or broken connectors
! Uneven wear on any of the tires
! Jerky motion
! Pulling to one side
! Bent or broken wheel assemblies
! Does not power up
! Powers up, but does not move
Corrective Maintenance
If the battery condition meter does not light up when you turn on the power:
! Check the harness connections. Make sure they are tight.
! Check the circuit breaker. Reset it if necessary.
! Check the battery connections.
If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers are available
at automotive parts stores. Disconnect both batteries before load testing and follow the directions that come with the load
tester. If either one of the batteries fails the load test, replace both of them. If your power chair still does not power up,
contact your authorized Pride Provider.
40
www.pridemobility.com
Jazzy 1113 ATS
NOTES
Jazzy 1113 ATS
www.pridemobility.com
41
NOTES
42
www.pridemobility.com
Jazzy 1113 ATS
Quality Control - Jazzy 1113 ATS
Inclusion of all Parts
Joystick Serial Number
Controller Serial Number
Left Motor Serial Number
Right Motor Serial Number
Fit and Finish
Performance
Pride keeps a more detailed report on file at the factory.
Date Inspected
Inspector
*INFMANU1801*
Product Serial #