Zanussi ZI 9220 FF User manual

ZI 1644
ZI 2444
Downloaded from Manuals
Instructions for the use of the instructions booklet
Notes which are important for your safety or for the proper functioning of the appliance
Supplementary information regarding operation and practical applications of the appliance.
Tips and notes concerning economical and environmentally sound use of the appliance
Safety Instructions
This information has been provided in the interests of your safety. Please read it before installing or
using the appliance. Please retain the instruction book for future reference. If owner ship is transferred,
please leave the user manual for the new owner.
Domestic Use
Child Safety
¥ The domestic refrigerators and freezers are
designed to be used specifically for the storage of
edible foodstuffs only.
¥ Check the appliance for transport damage. Under
no circumstances should a damaged appliance be
installed. In the event of damage please contact
your retailer.
¥ This appliance is heavy. The edges and projecting
parts of the cabinet may be sharp. Be careful when
moving the cabinet and always use gloves.
¥ Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
¥ Make sure that the power plug is not squashed or
damaged by the back of the appliance. Make sure
that the cable is not trapped underneath the
appliance, nor touches the motor.
¥ Do not remove the power cord by pulling on its
lead, particularly when the appliance is being
pulled out of its niche. If the power plug socket is
loose, do not insert the power plug. Damage to the
cord may cause a short-circuit, fire and/or electric
¥ Do not use electrical appliances inside the
¥ Do not keep carbonated drinks or bottles in the freezer
compartment. The glass bottles may break.
¥ Ice lollies can cause Ôfrost/freezer burnsÕ if
consumed straight from the freezer.
¥ It is dangerous to try and alter the specifications or
modify this product in any way.
¥ Under no circumstances should you attempt to
repair the appliance yourself. Refer to your local
Service Centre, and always insist on genuine spare
¥ This appliance is designed to be operated by
adults only. Do not allow the children to tamper
with the controls or play with the products. There is
a risk of suffocation! Keep packaging material
away from children!
Environment Protection
¥ This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with the
urban refuse and rubbish. Avoid damaging the
cooling unit. Information on your local disposal
sites may be obtained from your municipal
Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
Appliance Packaging Information
¥ The materials marked with the symbol
>PE< for polyethylene, e.g. sheet wrapping
>PS< for polystyrene, e.g. padding material
(always CFC-free)
>POM< polyoxymethylene, e.g. plastic clips.
All materials are environmentally sound!
on paper manufactured with environmentally sound processes
Disposal of old appliances
The symbol
on the product or on its packaging indicates that this product may not be treated as
household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical
and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or the shop where you purchased
the product.
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Use and Control Before Use / Refrigerator compartment - Starting the appliance / Temperature control . . .37
Refrigerator compartment - Internal parts / Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Freezer compartment - Temperature control / Interior accessories / Hints . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Maintenance Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Cleaning / Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Something not Working / Customer Service and Spare Parts / Technical Specifications . . . . . . . . . . . .41
Door reversal Inner door reversal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Installation Positioning / Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Building-in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Declaration of guarantee terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Use and Control
Before Use
Wait two hours before connecting the
appliance to allow the oil to flow back in the
¥ Before using the appliance for the first time, wash
the interior and all internal accessories with
lukewarm water and some neutral soap so as to
remove the typical smell of a brand-new product,
then dry thoroughly.
Do not use detergents or abrasive
powders, as these will damage the finish.
¥ Remove safety elements used for transportation.
Refrigerator compartment
Starting the appliance
¥ Insert the plug into the wall socket and turn the
thermostat knob clockwise beyond position ÇOÈ
¥ The thermostat control situated inside the fridge
compartment regulates the temperature of the
¥ Turn the thermostat control to the required setting.
Temperature Control
¥ The following effects are of significance in respect
of the interior temperature:
¥ Ambient temperature
¥ Quantity and temperature of the food stored;
¥ Frequency with which the door is opened and
how long it is left open
¥ the location of the appliance.
¥ The temperature inside the appliance is
automatically adjusted.
¥ Setting ã1Ò = hightest temperature, warmest
Downloaded from Manuals
¥ Setting ã6Ò = lowest temperature, coldest
¥ Setting ã¥Ò = Off
A medium setting is generally the most suitable.
Internal Parts
Storage shelves
¥ The shelves can be removed for cleaning.
¥ To permit storage of food packages of various
sizes, the shelves can be placed at different
¥ To remove the internal shelf pull forward until it can
be tipped up or down and removed.
¥ Please do the same in reverse to insert the shelf at
a different height.
The glass shelf above the vegetable drawers
and the bottle shelf should always remain in
position, to ensure correct air circulation.
Door shelves
¥ To permit storage of food packages of various
sizes, the central door shelf can be adjusted in
¥ Gradually pull the shelf in the direction of the
arrows until it comes free, then reposition as
¥ For more thorough cleaning, the top and bottom
door sheves can be easily removed and refitted in
Saving Energy
¥ Pay careful attention to where the cabinet is
placed. See the section ÒInstallationÓ. When
installed correctly the cabinet will consume less
¥ Try to avoid keeping the doors open for long
periods or opening the doors too frequently as
warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
¥ If the ambient temperature is high, the thermostat
knob is on the coldest setting (higher numbers) and
the appliance is fully loaded, the compressor may
run continuously, causing frost or ice to form on the
evaporator. If this happens, turn the knob to a
warmer setting (lower numbers) to allow automatic
defrosting and so a saving in electricity
¥ Do not place warm foods inside the appliance.
Allow warm foods to cool first.
¥ Put frozen food in the fridge to defrost. The cold in
the frozen food will then be used to cool the fridge.
¥ Keep the heat emitting condenser, the metall grille
on the rear wall of your appliance, always clean.
Hints for refrigeration
¥ Do not store warm food or evaporating liquids in
the refrigerator and do cover or wrap up the food,
particularly if it has a strong smell.
To help you use your refrigerator correctly, here are
some useful hints:
¥ Raw meat (beef, pork, lamb & poultry): wrap in
polythene bags and place on top of the salad
compartment, this being the coldest spot in the
Meat can only be stored safely in this way for
one or two days at the most.
¥ Cooked food, cold cuts, jelly, etc.: these should
be well covered and can be stored on any of the
wire shelves.
¥ Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom drawer/s.
¥ Butter & cheese: these should be placed in
special airtight containers or wrapped in aluminium
foil or polythene bags to keep out as much air as
¥ Milk bottles: these should have a top and should
be stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not
packed, must not be kept in the refrigerator.
from Manuals
Freezer compartment
Temperature Control
¥ To freeze fresh foods it is not necessary to change
the setting of the thermostat knob.
¥ For a quicker freezing operation, turn the
thermostat knob to the coldest setting; but
remember that, in this condition, the refrigerator
compartment temperature might drop below 0¡C. If
this occurs reset thermostat knob to a warmer
¥ At the first starting-up or after a period out of use,
before putting the products in the compartment, let
the appliance run for at least two hours on the
coldest setting, then turn the thermostat knob to
the normal operating position.
Interior Accessories
Ice-cube production
This appliance is equipped with one or more trays for
the production of ice-cubes.
Fill these trays with water, then put them in the
freezer compartment.
Do not use metallic instruments to remove
the trays from the freezer.
Freezing of fresh food and storage of frozen food
¥ Prepare food in small portions to enable it to be
rapidly and completely frozen and to make it
possible subsequently to thaw only the quantity
¥ Wrap up the food in aluminium foil or polythene
and make sure that the packages are airtight.
¥ Do not allow fresh, unfrozen food to touch food
which is already frozen, thus avoiding a rise in
temperature of the latter.
¥ Do not touch frozen food with wet hands. Your
hands could stick to the food and cause skin
¥ It is advisable to show the freezing-in date on each
individual pack to enable you to keep tab of the
storage time.
¥ Be sure that frozen foodstuffs are transferred from
the foodstore to the freezer in the shortest possible
¥ Do not put carbonated liquids (fizzy drinks,
etc.) in the freezing compartment as they may
¥ Once defrosted, food deteriorates rapidly and
cannot be refrozen.
Unplug the appliance before carrying out
any maintenance operation.
This appliance contains hydrocarbons in its
cooling unit maintenance and recharging must
therefore only be carried out by authorised
Refrigerator compartment
¥ Defrosting the refrigerator compartment is
automatic. The defrost water drains out through a
trough into a container at the back of the appliance,
above the motor compressor, where it evaporates.
¥ It is important to periodically clean the defrost
water drain hole.
Downloaded from Manuals
Freezer compartment
¥ Remove the frost with a plastic scraper.
¥ Whenever the thickness of the frost exceeds 5 mm
complete defrosting should be carried out.
Prooceed as follows:
¥ Remove any stored food, wrap it in several layers
of newspaper and put it in a cool place.
¥ Pull out the plug from the wall socket or turn the
thermostat knob to the ÇOÈ setting.
¥ Leave the door open, place a basin on the top shelf
of the refrigerator compartment, under the drain
hole, remove the plug as shown in the figure.
Never use metal objects for cleaning your
appliance as it may get damaged.
NEVER use detergents, abrasive powders,
highly perfumed cleaning products or wax
polishes to clean the interior as these will
damage the surface and leave a strong
Clean the inside with warm water and bicarbonate of
soda. Rinse and dry thoroughly.
To guarantee a safe operation of the fridge, once a
year remove the ventilation grille at the base and
clean the air channels with a vacuum cleaner.
When the appliance is not in use
Disconnect the appliance from the electricity supply.
Empty all foods and clean the appliance, leaving the
doors ajar to prevent unpleasant smells.
Changing the light bulb
¥ When defrosting is completed, dry the interior
thoroughly and refit the plug.
¥ Turn the thermostat knob back to the required
setting or replace the plug in the power socket.
¥ Reload the previously removed food into the
Never use sharp metal tools to scrape off
frost from the evaporator as you could
damage it.
Do not use a mechanical device or any
artificial means to speed up the thawing
process other than those recommended by
the manufacturer.
¥ Should the interior light fail to work, first switch off
the appliance and disconnect from the electricity
supply, then replace the bulb as follows:
1. unscrew the light cover securing screws.
2. unhook the moving part by pressing it as shown
in the figure.
3. Replace the bulb by other with another with the
same charcteristics.
from Manuals
Something not Working
Problems may be due to causes which can easily be solved before calling the Technical Service. Please
follow these instructions:
Door does not close
Weight surpasses the storage limit of the door shelf so spread weight more evenly or
take some products out.
The appliance is not properly installed. Please look in the ÒBuilding-inÓ section.
It is too warm inside the refrigerator
Set a lower temperature.
Distribute the food products to allow cold air to circulate around them.
Make sure that the door is completely closed and that the insulating strip is complete
and clean.
The temperature where the cabinet is placed is above normal room temperature.
It is too cold inside the refrigerator.
Turn the temperature regulator to a warmer setting temporarily.
The compressor works continuously.
Turn the thermostat knob to a lower number.
The temperature where the cabinet is placed is above normal room temperature.
Check that the ventilation is sufficient and that the ventilation openings are
The cause could be the introduction of large quantities of food and/or frequent
opening/closing of the door.
There is water inside/outside the refrigerator.
Sometimes is normal. During automatic defrosting frost thaws on the cooling plate.
Water comes out on the floor.
Place the drain hose at the back of the cabinet above the drain bowl.
Sometimes this is normal. Temperature control may cause clicking sounds when the
system is connected or disconnected.
The injected cooling gas may produce a gurgling sound while passing through the
The motor may cause a humming noise and/or slight bumping.
The insulation material used has a tendency to slighly increase noise levels, how ever it
allows for much better insulation and a lower energy consumption.
Customer service and spare parts
If you cannot find the remedy for a malfunction in
these operating instructions, please contact your
dealer or our customer service department and
consult the Guarantee card.
Selective ordering of replacement parts can save
unnecessary travel and costs.
For this reason always provide the following
appliance information:
¥ Model Name
This information can be found on the rating plate
inside the cabenit on the left hand wall. We
recommend that you enter this information here, so
that it is handy if needed.
¥ Model Number (PNC)
¥ Serial Number (S-No.)
Technical specifications
The technical data is indicated in the rating plate on the left side inside the appliance.
If there is a power failure when food is in the freezer, do not open the door of the freezer
compartment. The frozen food will not be affected if the power cut is of short duration (up to 12
hours) and the freezer compartment is full, otherwise, it is recommended that the food should be
used within a short time (a temperature increase of the frozen food shortens its safe storage
Downloaded from Manuals
Door reversal
The applianceÕs door has been locked in position for
transport by means of pins on both sides. According
to the door opening direction, remove relevant pins
at the top and at the bottom.
If the ambient temperature is cold (i.e. in
Winter), the gasket may not fit perfectly to the
cabinet. In that case, wait for the natural fitting
of the gasket or accelerate this process by
heating up the part involved with a normal
Inner door reversal
from Manuals
Take utmost care when handling your
appliance so as not to cause any damages to
the cooling unit with consequent possible fluid
¥ During normal operation, the condenser and
compressor at the back of the appliance heat up
considerably. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
¥ Important: if the supply cord is damaged, it must
be replaced by a special cord or assembly available from the manufacturer or its service agent.
50 mm
200 cm
¥ Unpack the cabinet and check that it is in good
condition and free of any transport damage.
¥ The appliance must not be located close to
radiators or gas cookers.
¥ Avoid prolonged exposure of the appliance to
direct sunlight.
¥ For safety reasons, minimum ventilation must be
as shown in Fig.
200 cm
The following table shows which ambient
temperature is correct for each climate classification:
+10 to +32¡C
+16 to +32¡C
+18 to +38¡C
+18 to +43¡C
When the ambient temperature is not included
within the range indicated for the class of this
appliance, the storage temperature in the
appliance cannot be guaranteed; therefore it is
advisable to use the food stored as soon as
Electrical connection
Before plugging in, ensure that the voltage and
frequency shown on the serial number plate
correspond to your domestic power supply.
Voltage can vary by ±6% of the rated voltage.
For operation with different voltages, a suitably sized
auto-transformer must be used.
The appliance must be earthed.
The power supply cable plug is provided with a
contact for this purpose.
If the domestic power supply socket is not
earthed. connect the appliance to a separate
earth in compliance with current regulations,
consulting a specialist technician.
responsibility if the above safety
precautions are not observed.
Attention: keep ventilation openings clear of
¥ It is necessary that the niche is provided with a
conduct of venti-lation having the following
Depth 50 mm
Width 540 mm
for an ambient temperature of
This appliance complies with the following E.E.C.
The climate classification can be found on the rating
plate, which is located inside the cabinet on the left
hand wall.
- 87/308 EEC of 2/6/87 relative to radio
interference suppression.
- 73/23 EEC of 19.2.73 (Low Voltage
and subsequent modifications.
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
It must be possible to disconnect the appliance
from the mains power supply; the plug must
therefore be easily accessible after installation.
Downloaded from Manuals
Dimensions of the recess
ZI 1644
ZI 2444
Height of housing (1) 880
Depth of housing (2) 550
Width of housing (3) 560
1. Fit the appliance in the niche by making sure that
it stands against the interior surface of the unit on
the side where the door hinges of the appliances
are fitted. Insert the appliance until the upper strip
butts up against the unit (1) and make sure that
the lower hinge is in line with the surface of the
unit (2).
50 mm
200 cm
It is necessary that the niche is provided with a
conduct of ventilation having the following
50 mm
540 mm
2. Press in the joint covers between the appliance
and the kitchen furniture.
200 cm
For appropriate venting, follow indications in the
3. Open the door and push the appliance against the
side of kitchen furniture opposite to that of the
appliance hinges. Fasten the appliance with 4
screws (I) provided in the kit included with the
from Manuals
4. Snap vent grill (B) and hinge cover (E) into
Apply blanking covers (C-D) as indicated.
7. Fix cover (Hc) on guide (Ha) until it clips into
5. Separate parts Ha, Hb, Hc, Hd as shown in the
8. Open the appliance door and the furniture door at
90¡. Insert the small square (Hb) into guide (Ha).
Put together the appliance door and the furniture
door and mark the holes as indicated in the figure.
ca. 50 mm
21 m
ca. 50 mm
21 m
6. Place guide (Ha) on the inside part of the furniture
door, up and down as shown in the figure and
mark the position of external holes. After having
drilled holes, fix the guide with the screws
9. Remove the squares and mark a distance of
8 mm from the outer edge of the door where the
nail must be fitted (K).
Downloaded from Manuals
10. Place the small square on the guide again and fix
it with the screws supplied.
Should the alignment of the furniture door be
necessary, use the clearance of slots.
At the end of this procedure, it is necessary to
check if the door of the furniture closes properly.
11. Fix cover (Hd) on the small square (Hb) until it
clips into place.
from Manuals
Our appliances are produced with the greatest of care. However, a defect may still occur. Our consumer services
department will repair this upon request, either during or after the guarantee period. The service life of the appliance will not,
however, be reduced as a result.
This declaration of guarantee terms is based on European Union Directive 99/44/EC and the provisions of the Civil Code.
The statutory rights that the consumer has under this legislation are not affected by this declaration of guarantee terms.
This declaration does not affect the vendorÕs statutory warranty to the end user. The appliance is guaranteed within the
context of and in adherence with the following terms:
1. In accordance with provisions laid down in paragraphs 2 to 15, we will remedy free of charge any defect that occurs
within 24 months from the date the appliance is delivered to the first end user. These guarantee terms do not apply in the
event of use for professional or equivalent purposes.
2. Performing the guarantee means that the appliance is returned to the condition it was in before the defect occurred.
Defective parts are replaced or repaired. Parts replaced free of charge become our property.
3. So as to avoid more severe damage, the defect must be brought to our attention immediately.
4. Applying the guarantee is subject to the consumer providing proof of purchase showing the purchase and/or delivery
5. The guarantee will not apply if damage caused to delicate parts, such as glass (vitreous ceramic), synthetic materials and
rubber, is the result of inappropriate use.
6. The guarantee cannot be called on for minor faults that do not affect the value or the overall reliability of the appliance.
7. The statutory warranty does not apply when defects are caused by:
¥ a chemical or electrochemical reaction caused by water,
¥ abnormal environmental conditions in general,
¥ unsuitable operating conditions,
¥ contact with harsh substances.
8. The guarantee does not apply to defects due to transport which have occurred outside of our responsibility. Nor will the
guarantee cover those caused by inadequate installation or assembly, lack of maintenance or failure to respect the
assembly instructions or directions for use.
9. Defects that result from repairs or measures carried out by people who are not qualified or expert or defects that result
from the addition of non-original accessories or spare parts are not covered by the guarantee.
10. Appliances that are easy to transport may be delivered or sent to the consumer services department. Home repairs are
only anticipated for bulky appliances or built-in appliances.
11. If the appliances are built-in, built-under, fixed or suspended in such a way that removing and replacing them in the
place where they are fitted takes more than half an hour, the costs that result therefrom will be charged for. Connected
damage caused by these removal and replacement operations will be the responsibility of the user.
12. If, during the guarantee period, repairing the same defect repeatedly is not conclusive, or if the repair costs are
considered disproportionate, in agreement with the consumer, the defective appliance may be replaced with another
appliance of the same value.
In this event, we reserve the right to ask for a financial contribution calculated according to the length of time it has been
13. A repair under guarantee does not mean that the normal guarantee period will be extended nor that a new guarantee
period begins.
14. We give a twelve month guarantee for repairs, limited to the same defect.
15. Except in the event where liability is legally imposed, this declaration of guarantee terms excludes any compensation for
damage outside the appliance for which the consumer wishes to assert his rights. In the event of legally admitted liability,
compensation will not exceed the purchase price paid for the appliance.
These guarantee terms are only valid for appliances purchased and used in Belgium. For exported appliances, the user
must first make sure that they satisfy the technical conditions (e.g.: voltage, frequency, installation instructions, type of gas,
etc.) for the country concerned and that they can withstand the local climatic and environmental conditions. For appliances
purchased abroad, the user must first ensure that they meet the qualifications required in Belgium. Non-essential or
requested adjustments are not covered by the guarantee and are not possible in all cases.
Our consumer services department is always at your disposal, even after the guarantee period has expired.
Address for our consumer services department:
Bergensesteenweg, 719 Ð 1502 LEMBEEK
Tel. 02.3630444
Downloaded from Manuals
Downloaded from Manuals