advertisement
Table of Contents
D-Link Web Smart Switch User Manual
Table of Contents
i i
Table of Contents
D-Link Web Smart Switch User Manual
i i i i
Table of Contents
D-Link Web Smart Switch User Manual
iii
Table of Contents
D-Link Web Smart Switch User Manual
i i v
About This Guide
D-Link Web Smart Switch User Manual
About This Guide
This guide provides instructions to install the D-Link Gigabit Web Smart Switch DGS-1210-10P/20/28/28P/52, how to use the SmartConsole Utility, and to configure Web-based Management step-by-step.
Note: The model you have purchased may appear slightly different from the illustrations shown in the document. Refer to the Product
Instruction and Technical Specification sections for detailed information about your switch, its components, network connections, and technical specifications.
This guide is mainly divided into four parts:
1. Hardware Installation: Step-by-step hardware installation procedures.
2.
3.
4.
Getting Started: A startup guide for basic switch installation and settings.
Smart Console Utility: An introduction to the central management system.
Configuration: Information about the function descriptions and configuration settings.
Terms/Usage
In this guide, the term “Switch” (first letter capitalized) refers to the Smart Switch, and “switch” (first letter lower case) refers to other Ethernet switches. Some technologies refer to terms “switch”, “bridge” and
“switching hubs” interchangeably, and both are commonly accepted for Ethernet switches.
A NOTE indicates important information that helps a better use of the device.
A CAUTION indicates potential property damage or personal injury.
Copyright and Trademarks
Information in this document is subjected to change without notice.
© 2012 D-Link Corporation. All rights reserved.
Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden.
Trademarks used in this text: D-Link and the D-LINK logo are trademarks of D-Link Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. D-Link Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
1
1 Product Introduction
D-Link Web Smart Switch User Manual
1
Product Introduction
Thank you and congratulations on your purchase of D-Link Web Smart Switch Products.
D-Link's next generation Web Smart Ethernet switch series blends plug-and-play simplicity with exceptional value and reliability for small and medium-sized business (SMB) networking. All models are housed in a new style rack-mount metal case with easy-to-view front panel diagnostic LEDs, and provides advanced features including network security, traffic segmentation, QoS and versatile management.
Flexible Port Configurations. The DGS-1210 series is the new generation of Web Smart series. It provides a variety of port counts- 16, 24 or 48 10/100/1000Mbps ports plus 4 SFP ports. Besides, the series offers 2
PoE models with 8 10/100/1000Mbps PoE ports plus 2 SFP ports and 24 10/100/1000Mbps PoE ports plus 4
SFP ports.
The first 4 ports of DGS-1210-10P/28P also support up to 30 watts PoE power for the connections of PoE +
Power Devices, allowing them to be deployed at difficult places such as on high walls and ceilings, where AC power outlets are not readily available.
D-Link Green Technology. D-Link Green devices are about providing eco-friendly alternatives without compromising performance. D-Link Green Technology includes a number of innovations to reduce energy consumption on DGS-1210 series such as shutting down a port, or turning off some LED indicators, or adjusting the power usage according to the Ethernet cable connected to it. For PoE model such as DGS-
1210-10P/28P, D-Link Green Technology offers Time-based PoE feature to shut down per port power off working hours.
Extensive Layer 2 Features. Implemented as complete L2 devices, these switches include functions such as IGMP snooping, port mirroring, Spanning Tree, 802.3ad LACP and Loopback Detection to enhance performance and network resiliency.
Traffic Segmentation, QoS and Auto Surveillance VLAN. The switches support 802.1Q VLAN standard tagging to enhance network security and performance. The switches also support 802.1p priority queues, enabling users to run bandwidth-sensitive applications such as streaming multimedia by prioritizing that traffic in network. These functions allow switches to work seamlessly with VLAN and 802.1p traffic in the network. Auto Surveillance VLAN will automatically place the vedio traffic from pre-defined IP surveillance devices to an assigned VLAN with higher priority, so it can be separated from normal data traffic. Asymmetric
VLAN is implemented in these switches for a more efficient use of shared resources, such as server or gateway devices.
Network Security. D-Link’s innovative Safeguard Engine function protects the switches against traffic flooding caused by virus attacks. Additional features like 802.1X port-based authentication provide access control of the network with external RADIUS servers. ACL is a powerful tool to screen unwanted IP or MAC traffic. Storm Control can help to keep the network from being overwhelmed by abnormal traffic. Port
Security is another simple but useful authentication method to maintain the network device integrity.
Versatile Management. The new generation of D-Link Web Smart Switches provides growing businesses with a simple and easy management of their network, using an intuitive SmartConsole utility or a Web-Based management interface that allows administrators to remotely control their network down to the port level. The
SmartConsole easily allows customers to discover multiple D-Link web smart switches with the same L2 network segment connected to the user’s local PC. With this utility, users do not need to change the IP address of the PC and provide easy initial settings of the smart switches. The switches within the same L2 network segment connected to the user’s local PC are displayed on the screen for instant access. It allows extensive switch configuration settings, and basic configuration of discovered devices, such as a password change or firmware upgrade.
Users can also access the switch via TELNET. Some basic tasks can be performed such as changing the
Switch IP address, resetting the settings to factory defaults, setting the administrator password, rebooting the
Switch, or upgrading the Switch firmware by using the Command Line Interface (CLI).
2
1 Product Introduction
D-Link Web Smart Switch User Manual
In addition, users can utilize the SNMP MIB (Management Information Base) to poll the switches for information about the status, or send out traps of abnormal events. SNMP support allows users to integrate the switches with other third-party devices for management in an SNMP-enabled environment. D-Link Web
Smart Switches also come with the D-View plug-in module that works with D-View 6 SNMP Management
Software, and provides easy-to-use graphic interface and facilitates the operation efficiency.
DGS-1210-10P
8-Port 10/100/1000Mbps plus 2 combo ports of 1000Base-T/SFP ports Web Smart PoE Switch.
Front Panel
Figure 1.1 – DGS-1210-10P Front Panel
SFP ports for optical transceivers
Power LED : The Power LED lights up when the Switch is connected to a power source.
Pwr Max: The Pwr Max LED lights up when the Switch reaches the maximum power budget defined by the administrator via PoE System Settings page of Web GUI or the default power budget of 78 Watts.
Reset: By pressing the Reset button for 5 seconds, the Switch will change back to the default configuration and all changes will be lost.
Mode: By pressing the Mode button, the Port LED will switch between Link/Act and PoE modes.
Port Link/Act/Speed LED (1-8, 9T, 10T 9F, 10F): When mode LED lights up in Link/Act mode, the port
LEDs indicate a network link through the corresponding port. Blinking indicates the Switch is either sending or receiving data to the port. When the port LED glows in amber, it indicates the port is running on 10M or
100M. When the port LED glows in green, it is running on 1000Mbps.
CAUTION: The MiniGBIC ports should use UL listed Optical
Transceiver product, Rated Laser Class I. 3.3Vdc.
CAUTION: The ITE is to be connected only to PoE networks without routing to the outside plant.
Port PoE LED (1-8): When mode LED lights up in PoE mode, the port LEDs indicate powering status over the corresponding port. DGS-1210-10P can supply up to 30W on port 1- 4, which are marked with black background color on front panel, for IEEE802.3at compliance PDs.
Rear Panel
Figure 1.2 – DGS-1210-10P Rear Panel
Power: The power port is where to connect the AC power cord.
DGS-1210-20
16-Port 10/100/1000Mbps plus 4 SFP Slot Web Smart Switch.
3
1 Product Introduction
Front Panel
D-Link Web Smart Switch User Manual
Figure 1.3 – DGS-1210-20 Front Panel
Power LED : The Power LED lights up when the Switch is connected to a power source.
Port Link/Act/Speed LED (1-16, 17F, 18F, 19F, 20F): The Link/Act/Speed LED flashes, which indicates a network link through the corresponding port. Blinking indicates that the Switch is either sending or receiving data to the port. When a port has an amber light, this indicates that the port is running on 10M or 100M.
When it has a green light it is running on 1000M.
CAUTION: The MiniGBIC ports should use UL listed Optical
Transceiver product, Rated Laser Class I. 3.3Vdc.
Reset: By pressing the Reset button for 5 seconds, the Switch will change back to the default configuration and all changes will be lost.
Rear Panel
Figure 1.4 – DGS-1210-20 Rear Panel
Power: The power port is where to connect the AC power cord.
DGS-1210-28
24-Port 10/100/1000Mbps plus 4 SFP Slot Web Smart Switch.
Front Panel
Figure 1.5 – DGS-1210-28 Front Panel
Power LED : The Power LED lights up when the Switch is connected to a power source.
Port Link/Act/Speed LED (1-24, 25F, 26F, 27F, 28F): The Link/Act/Speed LED flashes, which indicates a network link through the corresponding port. Blinking indicates that the Switch is either sending or receiving data to the port. When a port has an amber light, this indicates that the port is running on 10M or 100M.
When it has a green light it is running on 1000M.
Reset: Press the Reset button for 5 seconds to reset the Switch back to the default settings. All previous changes will be lost.
CAUTION: The MiniGBIC ports should use UL listed Optical
Transceiver product, Rated Laser Class I. 3.3Vdc.
4
1 Product Introduction
Rear Panel
D-Link Web Smart Switch User Manual
Figure 1.6 – DGS-1210-28 Rear Panel
Power: Connect the supplied AC power cable to this port.
DGS-1210-28P
24-Port 10/100/1000Mbps plus 4 SFP ports Web Smart PoE Switch.
Front Panel
Figure 2.7 – DGS-1210-28P Front Panel
Power LED : The Power LED lights up when the Switch is connected to a power source.
Pwr Max: The Pwr Max LED lights up when the Switch reaches the maximum power budget defined by the administrator via PoE System Settings page of Web GUI or the default power budget of 185 Watts.
Reset: By pressing the Reset button for 5 seconds, the Switch will change back to the default configuration and all changes will be lost.
Mode: By pressing the Mode button, the Port LED will switch between Link/Act and PoE modes.
Port Link/Act/Speed LED (1-24, 25F, 26F, 27F, 28F): When mode LED lights up in Link/Act mode, the port
LEDs indicate a network link through the corresponding port. Blinking indicates the Switch is either sending or receiving data to the port. When the port LED glows in amber, it indicates the port is running on 10M or
100M. When the port LED glows in green, it is running on 1000Mbps.
Fan: The Fan LED lights green when fans work well, and lights red when fans fail.
CAUTION: The MiniGBIC ports should use UL listed Optical
Transceiver product, Rated Laser Class I. 3.3Vdc.
CAUTION: The ITE is to be connected only to PoE networks without routing to the outside plant.
Port PoE LED (1-24): When mode LED lights up in PoE mode, the port LEDs indicate powering status over the corresponding port. DGS-1210-28P can supply up to 30W on port 1- 4, which are marked with black background color on front panel, for IEEE802.3at compliance PDs.
Rear Panel
Figure 1.8 – DGS-1210-28P Rear Panel
Power: The power port is where to connect the AC power cord.
DGS-1210-52
48-Port 10/100/1000Mbps plus 4 SFP Slot Web Smart Switch.
5
1 Product Introduction
Front Panel
D-Link Web Smart Switch User Manual
Figure 1.9 – DGS-1210-52 Front Panel
Power LED : The Power LED lights up when the Switch is connected to a power source.
Port Link/Act/Speed LED (1-48, 49F, 50F, 51F, 52F): The Link/Act/Speed LED flashes, which indicates a network link through the corresponding port. Blinking indicates that the Switch is either sending or receiving data to the port. When a port has an amber light, this indicates that the port is running on 10M or 100M.
When it has a green light it is running on 1000M.
Fan: The Fan LED lights green when fans work well, and lights red when fans fail.
Reset: Press the Reset button for 5 seconds to reset the Switch back to the default settings. All previous changes will be lost.
CAUTION: The MiniGBIC ports should use UL listed Optical
Transceiver product, Rated Laser Class I. 3.3Vdc.
Rear Panel
Figure 1.10 – DGS-1210-52 Rear Panel
Power: Connect the supplied AC power cable to this port.
6
2 Hardware Installation
D-Link Web Smart Switch User Manual
2
Hardware Installation
This chapter provides unpacking and installation information for the D-Link Web-Smart Switch.
Step 1: Unpacking
Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the
User Manual to make sure all items are present and undamaged. If any item is missing or damaged, please contact your local D-Link reseller for replacement.
One D-Link Web-Smart Switch
One AC power cord
Four rubber feet
Screws and two mounting brackets
One Multi-lingual Getting Started Guide
One CD with User Manual, SmartConsole Utility program, and D-View Module
If any item is found missing or damaged, please contact the local reseller for replacement.
Step 2: Switch Installation
For safe switch installation and operation, it is recommended that you:
Visually inspect the power cord to see that it is secured fully to the AC power connector.
Make sure that there is proper heat dissipation and adequate ventilation around the switch.
Do not place heavy objects on the switch.
Desktop or Shelf Installation
When installing the switch on a desktop or shelf, the rubber feet included with the device must be attached on the bottom at each corner of the device’s base. Allow enough ventilation space between the device and the objects around it.
Figure 2.1 – Attach the adhesive rubber pads to the bottom
Rack Installation
The switch can be mounted in an EIA standard size 19-inch rack, which can be placed in a wiring closet with other equipment. To install, attach the mounting brackets to the switch’s side panels (one on each side) and secure them with the screws provided (please note that these brackets are not designed for palm size switches).
Figure 2.2 – Attach the mounting brackets to the Switch
7
2 Hardware Installation
D-Link Web Smart Switch User Manual
Then, use the screws provided with the equipment rack to mount the switch in the rack.
Figure 2.3 – Mount the Switch in the rack or chassis
Please be aware of following safety Instructions when installing:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit, and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips)."
Step 3 – Plugging in the AC Power Cord
Users may now connect the AC power cord into the rear of the switch and to an electrical outlet (preferably one that is grounded and surge protected).
Figure 2.4 –Plugging the switch into an outlet
8
2 Hardware Installation
D-Link Web Smart Switch User Manual
Power Failure
As a precaution, the switch should be unplugged in case of power failure. When power is resumed, plug the switch back in.
9
3 Getting Started
D-Link Web Smart Switch User Manual
3
Getting Started
This chapter introduces the management interface of D-Link Web-Smart Switch.
Management Options
The D-Link Web Smart Switch can be managed through any port on the device by using the Web-based
Management, or through any PC using the SmartConsole Utility.
Each switch must be assigned its own IP Address, which is used for communication with the Web-Based
Management or a SNMP network manager. The PC should have an IP address in the same range as the switch. Each switch can allow up to four users to access the Web-Based Management concurrently.
However, if you want to manage multiple D-Link Web Smart Switches, the SmartConsole Utility is a more convenient choice. By using the SmartConsole Utility, you do not need to change the IP address of your PC and it is easier to initialize multiple Smart Switches.
Please refer to the following installation instructions for the Web-based Management and the SmartConsole
Utility.
Using Web-based Management
After a successful physical installation, you can configure the Switch, monitor the network status, and display statistics using a web browser.
Supported Web Browsers
The embedded Web-based Management currently supports the following web browsers:
Internet Explorer 6 or later version
Netscape 8 or later version
Firefox 3.0 or later version
Chrome 5.0 or later version
Safari 4.0 or later version
Opera 10 or later version
Connecting to the Switch
You will need the following equipment to begin the web configuration of your device:
1. A PC with a RJ-45 Ethernet connection
2. A standard Ethernet cable
Connect the Ethernet cable to any of the ports on the front panel of the switch and to the Ethernet port on the
PC.
Figure 3.1 – Connected Ethernet cable
10
3 Getting Started
D-Link Web Smart Switch User Manual
Login Web-based Management
In order to login and configure the switch via an Ethernet connection, the PC must have an IP address in the same subnet as the switch. For example, if the switch has an IP address of 10.90.90.90, the PC should have an IP address of 10.x.y.z (where x/y is a number between 0 ~ 254 and z is a number between 1 ~ 254), and a subnet mask of 255.0.0.0. There are two ways to launch the Web-based Management, you may either click the Web Access button at the top of the SmartConsole Utility or open the web browser and enter 10.90.90.90
(the factory-default IP address) in the address bar. Then press <Enter>.
Figure 3.2 –Enter the IP address 10.90.90.90 in the web browser
NOTE: The switch's factory default IP address is
10.90.90.90 with a subnet mask of 255.0.0.0 and a default gateway of 0.0.0.0.
The web configuration can also be accessed through the SmartConsole Utility. Open the SmartConsole
Utility and double-click the switch as it appears in the Monitor List. This will automatically load the web configuration in your web browser.
When the following logon dialog box appears, enter the password and choose the language of the Webbased Management interface then click OK.
The switch supports 10 languages including English, Traditional Chinese, Simplified Chinese, German,
Spanish, French, Italian, Portuguese, Japanese and Russian. By default, the password is admin and the language is English.
Figure 3.3 – Logon Dialog Box
Smart Wizard
After a successful login, the Smart Wizard will guide you through essential settings of the D-Link Web Smart
Switch. Please refer to the Smart Wizard Configuration section for details.
Web-based Management
By clicking the Exit button in the Smart Wizard, you will enter the Web-based Management interface. Please
refer to Chapter 5 Configuration for detailed instructions.
SmartConsole Utility
The SmartConsole Utility included in the installation CD is a program for discovering D-Link Smart Switches within the same network segment connected to your PC. This tool is only for computers running Windows 7,
Vista, XP, or 2000 on both 32/64 bit systems. There are two options for the installation of the SmartConsole
Utility; one is through the autorun program on the installation CD and the other is manual installation.
1 1
3 Getting Started
D-Link Web Smart Switch User Manual
NOTE: Please be sure to uninstall any existing
SmartConsole Utility from your PC before installing the latest SmartConsole Utility.
Option 1: Follow these steps to install the SmartConsole Utility via the autorun program on the installation
CD.
1. Insert the Utility CD into your CD-Rom/DVD-Rom Drive.
2. The autorun program will appear automatically.
3. Click on the ”Install SmartConsole Utility” button and an installation wizard will guide you through the process.
4. After successfully installing the SmartConsole Utility, you can open the utility by clicking Start >
Programs > D-Link SmartConsole Utility.
5. Connect the Smart Switch to the same L2 network segment of your PC and use the SmartConsole
Utility to discover the Smart Switches.
Option 2: Follow these steps to install the SmartConsole Utility manually.
1. Insert the Utility CD into your CD-Rom/DVD-Rom Drive.
2. From the Start menu on the Windows desktop, click Computer..
3. In the Run dialog box, type D:\D-Link SmartConsole Utility\D-Link_SmartConsole_Utility_v3.00.10.exe
(where D:\ represents the drive letter of your CD-Rom) and click OK.
4. Follow the on-screen instructions to install the utility.
5. Upon completion, go to Start > Programs > D-Link SmartConsole Utility and open the SmartConsole
Utility.
6. Connect the Smart Switch to the same L2 network segment of your PC and use the SmartConsole
Utility to discover the Smart Switches.
NOTE: The current SmartConsole Utility does not support IPv6 feature. Please be sure to install the
SmartConsole Utility from you PC with IPv4 address. After installed SmartConsole Utility, then it can discover the DGS-1210 series with IPv6 address.
12
4 SmartConsole Utility
D-Link Web Smart Switch User Manual
4
SmartConsole Utility
The D-Link SmartConsole Utility allows the administrator to quickly discover all D-Link smart switches, which are in the same domain of the PC, collect traps and log messages, and quick access to basic configurations of the switch.
The SmartConsole Utility consists of three parts, Device Configurations at the top, Device List as the main body, and SmartConsole Settings at the left.
Figure 4.1 – SmartConsole Utility
SmartConsole Settings
The SmartConsole Settings at the left has five icons, Utility Settings, Log, Trap, Monitor list, and About.
Utility Settings
Click this icon to launch the Utility Settings window. Refresh time refreshes the devices, which were selected as monitored devices in the Device List. Choices include 15 secs, 30 secs, 1 mins, 2 mins, and 5
mins for selecting the monitoring time intervals. Utility Group Interval establishes the intervals (in seconds) that the Switch will be discovered in the SmartConsole Device List.
Figure 4.2 – SmartConsole Utility Settings
NOTE: If the Group Interval is set to 0, IGMP
Snooping must be disabled in the Switch, or the
Web-Smart Switch will not be discovered.
Log
Click this icon to launch the Log window. Click View Log to show the events of the SmartConsole Utility and the device. Time indicates when the message was received, Location indicates where the message was
1 3
4 SmartConsole Utility
D-Link Web Smart Switch User Manual received and IP Address denotes where it comes from. Click Refresh to redisplay all log entries, click Clear to clear all log entries. Click Exit to exit.
Figure 4.3 – SmartConsole Log
Trap
By setting up in “Trap to SmartConsole Utility” in D-Link Web Smart switches, traps can be collected by the designated host PC with the SmartConsole Utility installed. Click this icon to launch the Trap window. Click
View Trap to show the events of the SmartConsole Utility and the device. Time indicates when the trap message was received, Location indicates the physical location of the switch that sends out traps, IP
Address denotes where it comes from and Event shows the content of this trap message. Click Refresh to redisplay all traps, click Clear to clear all entries. Click Exit to exit.
Figure 4.4 – SmartConsole Trap
The trap icon in the SmartConsole Settings will change while receiving new trap messages. Please see below for detailed description.
Icon Description
No new traps
New traps was received
14
4 SmartConsole Utility
Monitor List
By clicking on this icon you will see below options:
D-Link Web Smart Switch User Manual
Figure 4.5 – SmartConsole Monitor List
Save: Records the setting of the Device List as default for the next time the SmartConsole Utility is used.
Save As: Records the setting of the Device List in an appointed filename and file path.
Restore: Manually reload a Device List setting file.
About
Click this icon to launch the SmartConsole Info window.
Figure 4.6 – SmartConsole About
Device Configuration
The Device Configuration in the SmartConsole Utility has five icons:
Device Settings
Password Setting
Firmware Upgrade
DHCP Refresh
Web Access and the , , device buttons for the Device List.
Device Settings
Select a switch from the Device List. Click on this icon to launch the Device Settings window. Here you can configure the Product Name, IP Address, Gateway, Subnet Mask, System Name, Location, Trap Host IP,
Switch Group Interval, and DHCP Client Setting of the Switch.
To apply the configuration, insert the correct device password in the Confirm Password box and then click
OK.
1 5
4 SmartConsole Utility
D-Link Web Smart Switch User Manual
Figure 4.7 – SmartConsole Device Settings
Password Setting
Select a switch from the Device List. Click on this icon to launch the Password Setting window. Here you can enter a new password and confirm it.
Figure 4.8 – SmartConsole Password Setting
Firmware Upgrade
Select one or many switches of the same model name from the Device List. Click on this icon to launch the
Firmware Upgrade window. Specify the Firmware Path (or Browse for one) that you are going to use. Input the correct password of the device, and then click Upgrade. The state will show "OK" after completion, or
“Fail” if the firmware upgrade fails or cannot be completed for any reason.
16
4 SmartConsole Utility
D-Link Web Smart Switch User Manual
Figure 4.9 – Firmware Upgrade
CAUTION: Do not disconnect the PC or remove the power cord from the device until the upgrade completes. The software may be corrupted because of the incomplete firmware upgrade.
DHCP Refresh:
If a DHCP-client enabled switch in the Device List shows the default IP is still used, it means the device did not receive an IP address from the DHCP server successfully. Select that switch and click the DHCP refresh icon. Enter the correct Device Password and then click OK. The device will renew the IP address from the
DHCP server.
Figure 4.10 – DHCP Refresh
Web Access
Select a switch from the Device List. Click this icon to launch your Internet browser (eg. The Internet
Explorer). Here you can configure the Switch through the Web-based Management utility. You may also get into the Web-based Management by double-clicking the device in the device list.
Add(+), Delete(-) and Discover the device
Click the Discovery button to display all of the Web-Smart devices located in the same domain with the management PC.
Click the + and insert a device IP address to add a device into the Discover List, or select a device and click the – button to remove it.
1 7
4 SmartConsole Utility
D-Link Web Smart Switch User Manual
Figure 4.11 – SmartConsole Add device
Figure 4.12 – SmartConsole Delete device
Device List
This list displays all discovered Web-Smart devices on the network.
Figure 4.13 – SmartConsole Device List
Definitions of the Device List features:
Select: Click the Select to choose a switch for configuration settings.
Monitor: Click the Monitor button and the SmartConsole will collect the trap and log data from the device.
The in the monitor means the device was discovered by SmartConsole. Click the icon to have the device to continue updating the information, such as system log or trap to the SmartConsole Utility. The icon will appear . When the device was detected as not reachable, the icon will change to if the power or the cable of this device is disconnected.
Product Name: Displays the device product name.
IP Address: Displays the current IP addresses of devices.
Subnet Mask: Displays the Subnet Mask setting of the device.
Gateway: Displays the Gateway setting of the device.
MAC Address: Displays the device MAC Addresses.
Firmware version: Displays the current Firmware version of this device.
System Name: Displays the appointed device system name.
Location: Displays the location of the appointed device.
. Please check
SNMP: Displays the SNMP status of the device.
Trap IP: Displays the IP address of the host where the Trap information will be sent.
DHCP: Specify if the device gets the IP address from a DHCP server.
Group Interval: Displays the intervals (in seconds) that the Switch will be discovered in the SmartConsole
Device List.
NOTE: If the devices are marked red in the device list, it means that a firmware upgrade is required
18
4 SmartConsole Utility
D-Link Web Smart Switch User Manual again.
NOTE: If the IP address of device is showed with
IPv6 address, then it can not be configured with
Smartconsole Utility. The user needs to double click the selected device and login the web for configuration.
1 9
5 Configuration
D-Link Web Smart Switch User Manual
5
Configuration
The features and functions of the D-Link Web Smart Switch can be configured for optimum use through the
Web-based Management Utility.
Smart Wizard Configuration
After a successful login, the Smart Wizard will guide you through essential settings of the D-Link Web Smart
Switch. If you do not plan to change anything, click Exit to leave the Wizard and enter the Web Interface.
You can also skip it by clicking Ignore the Wizard next time for the next time you logon to the Web-based
Management.
IP Information
IP Information will guide you to do basic configurations in 3 steps for the IP Information, access password, and SNMP.
Select Static, DHCP or BOOTP, and enter the desired new IP Address, select the Netmask and enter the
Gateway address, then click the Next button to enter the next Password setting page. (No need to enter IP
Address, Netmask and Gateway if DHCP and BOOTP are selected.) The Smart Wizard is for the quick
setting in IPv4 environment. For IPv6 network, please go to System > IPv6 System Settings .
If you are not changing the settings, click Exit button to go back to the main page. Or you can click on Ignore the wizard next time to skip wizard setting when the switch boots up .
Figure 5.1 – IP Information in Smart Wizard
NOTE: The Smart Wizard supports quick settings for IPv4 network.
Password
Type the desired new password in the Password box and again in the Confirm Password, then click the
Next button to the SNMP setting page.
20
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.2 – Password in Smart Wizard
SNMP
The SNMP Setting allows you to quickly enable/disable the SNMP function. The default SNMP Setting is
Disabled. Click Enabled and then click Apply to make it effective.
Figure 5.3 – SNMP in Smart Wizard
NOTE: Changing the system IP address will disconnect you from the current connection.
Please enter the correct IP address in the Web browser again and make sure your PC is in the
same subnet with the switch. See Login Webbased Management for a detailed description.
If you want to change the settings, click OK and start a new web browser.
2 1
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.4 – Confirm the changes of IP address in Smart Wizard
22
5 Configuration
D-Link Web Smart Switch User Manual
Web-based Management
After clicking the Exit button in Smart Wizard you will see the screen below:
Figure 5.5 – Web-based Management
The above image is the Web-based Management screen. The three main areas are the Tool Bar on top, the
Function Tree, and the Main Configuration Screen.
The Tool Bar provides a quick and convenient way for essential utility functions like firmware and configuration management.
By choosing different functions in the Function Tree, you can change all the settings in the Main
Configuration Screen. The main configuration screen will show the current status of your Switch by clicking the model name on top of the function tree.
At the upper right corner of the screen the username and current IP address will be displayed.
Under the username is the Logout button. Click this to end this session.
NOTE: If you close the web browser without clicking the Logout button first, then it will be seen as an abnormal exit and the login session will still be occupied.
Finally, by clicking on the D-Link logo at the upper-left corner of the screen you will be redirected to the local
D-Link website.
2 3
5 Configuration
D-Link Web Smart Switch User Manual
Tool Bar > Save Menu
The Save Menu provides Save Configuration and Save Log functions.
Figure 5.6 – Save Menu
Save Configuration
Select to save the entire configuration changes you have made to the device to switch’s non-volatile RAM.
Figure 5.7 – Save Configuration
Save Log
Save the log entries to your local drive and a pop-up message will prompt you for the file path. You can view or edit the log file by using text editor (e.g. Notepad).
Figure 5.8 – Save Log
Tool Bar > Tool Menu
The Tool Menu offers global function controls such as Reset, Reset System, Reboot Device, Configuration
Backup and Restore, Firmware Backup and Upgrade.
Figure 5.9 – Tool Menu
Reset
Provide a safe reset option for the Switch. All configuration settings in non-volatile RAM will be reset to factory default except for the IP address.
Figure 5.10 – Tool Menu > Reset
Reset System
Provide another safe reset option for the Switch. All configuration settings in non-volatile RAM will reset to factory default and the Switch will reboot.
Figure 5.11 – Tool Menu > Reset System
Reboot Device
Provide a safe way to reboot the system. Click Reboot to restart the switch.
24
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.12 – Tool Menu > Reboot Device
Configuration Backup and Restore
Allow the current configuration settings to be saved to a file (not including the password), and if necessary, you can restore configuration settings from this file. Two methods can be selected: HTTP or TFTP.
Figure 5.13 – Tool Menu > Configure Backup and Restore
HTTP: Backup or restore the configuration file to or from your local drive.
Click Backup to save the current settings to your disk.
Click Browse to browse your inventories for a saved backup settings file.
Click Restore after selecting the backup settings file you want to restore.
TFTP: TFTP (Trivial File Transfer Protocol) is a file transfer protocol that allows you to transfer files to a remote TFTP server. Specify TFTP Server IP Address with IPv4 or IPv6 address and TFTP File Name for the configuration file you want to save to / restore from.
Click Backup to save the current settings to the TFTP server.
Click Restore after selecting the backup settings file you want to restore.
Note: Switch will reboot after restore, and all current configurations will be lost
Firmware Backup and Upgrade
Allow for the firmware to be saved, or for an existing firmware file to be uploaded to the Switch. Two methods can be selected: HTTP or TFTP.
2 5
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.14 – Tool Menu > Firmware Backup and Upload
HTTP: Backup or upgrade the firmware to or from your local PC drive.
Click Backup to save the firmware to your disk.
Click Browse to browse your inventories for a saved firmware file.
Click Upgrade after selecting the firmware file you want to restore.
TFTP: Backup or upgrade the firmware to or from a remote TFTP server. Specify TFTP Server IP Address with IPv4 or IPv6 address and TFTP File Name for the configuration file you want to save to / restore from.
Click Backup to save the firmware to the TFTP server.
Click Upgrade after selecting the firmware file you want to restore.
CAUTION: Do not disconnect the PC or remove the power cord from device until the upgrade completes. The Switch may crash if the
Firmware upgrade is incomplete.
Tool Bar > Smart Wizard
By clicking the Smart Wizard button, you can return to the Smart Wizard if you wish to make any changes there.
Tool Bar > Online Help
The Online Help provides two ways of online support: D-Link Support Site will lead you to the D-Link website where you can find online resources such as updated firmware images; User Guide can offer an immediate reference for the feature definition or configuration guide.
Figure 5.15 – Online Help
26
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.16 – User Guide Micro Site
2 7
5 Configuration
D-Link Web Smart Switch User Manual
Function Tree
All configuration options on the switch are accessed through the Setup menu on the left side of the screen.
Click on the setup item that you want to configure. The following sections provide more detailed description of each feature and function.
Figure 5.17 –Function Tree
Device Information
The Device Information provides an overview of the switch, including essential information such as firmware
& hardware information, and IP address.
It also offers an overall status of common software features:
RSTP: Click Settings to link to L2 Functions > Spanning Tree > STP Global Settings. Default is disabled.
Port Mirroring: Click Settings to link to L2 Functions > Port Mirroring. Default is disabled.
Storm Control: Click Settings to link to Security > Storm Control. Default is disabled.
DHCP Client: Click Settings to link to System > System Settings. Default is disabled.
Jumbo Frame: Click Settings to link to L2 Functions > Jumbo Frame. Default is disabled.
SNMP Status: Click Settings to link to SNMP > SNMP > SNMP Global Settings. Default is disabled.
802.1X Status: Click Settings to link to AAA > 802.1X > 802.1X Settings. Default is disabled.
Safeguard Engine: Click Settings to link to Security > Safeguard Engine. Default is enabled.
IGMP Snooping: Click Settings to link to L2 Functions > Multicast > IGMP Snooping. Default is disabled.
Power Saving: Click Settings to link to System > Power Saving. Default is disabled.
28
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.18 – Device Information
System > System Settings
The System Setting allows the user to configure the IP address and the basic system information of the
Switch.
IP Information: There are three ways for the switch to obtain an IP address: Static, DHCP (Dynamic Host
Configuration Protocol) and BOOTP.
When using static mode, the IP Address, NetMask and Gateway can be manually configured. When using
DHCP mode, the Switch will first look for a DHCP server to provide it with an IP address (including network mask and default gateway) before using the default or previously entered settings. By default the IP setting is static mode with IP address is 10.90.90.90 and subnet mask is 255.0.0.0.
System Information: By entering a System Name and System Location, the device can more easily be recognized through the SmartConsole Utility and from other Web-Smart devices on the LAN.
Login Timeout: The Login Timeout controls the idle time-out period for security purposes, and when there is no action for a specific time span in the Web-based Management. If the current session times out (expires), the user is required a re-login before using the Web-based Management again. Selective range is from 3 to
30 minutes, and the default setting is 5 minutes.
Group Interval: The D-Link Web Smart Switch will routinely send report packets to the SmartConsole Utility in order to maintain the information integrity. The user can adjust the Group Interval to optimal frequency.
Selective range is from 120 to 1225 seconds, and 0 means disabling the reporting function, and the default setting is 120 seconds.
2 9
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.19 – System > System Settings
System > IPv6 System Settings
The IPv6 System Settings page allow user to configure the IPv6 system information.
Figure 5.20 – System > IPv6 System Settings
IPv6 System Settings:
Interface Name: Displays the interface name of IPv6.
IPv6 State: Specifies the IPv6 to be enabled or disabled.
DHCPv6 Client: Specifies the DHCPv6 client to be enabled or disabled.
IPv6 Network Address: Specifies the IPv6 Network Address.
NS Retransmit Time Settings:
NS Retransmit Time (1-3600): Specifies the NS retransmit time for IPv6. The field range is 1-3600, and default is 1 second.
Automatic Link Local State Settings:
Automatic Link Local Address: Specifies the automatic link is enabled or disabled.
Click Apply for the settings to take effect.
System > IPv6 Route Settings
The IPv6 Route Settings page allows user to configure the IPv6 route settings.
30
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.21 – System > IPv6 Route Settings
IP Interface: Specify the IP interface which to be created.
Default Gateway: The corresponding IPv6 address for the next hop Gateway address in IPv6 format..
Metric: Represents the metric value of the IP interface entered into the table. This field may read a number between 1 and 65535.
Click Create to accept the changes made, and click the Delete button to remove the entry.
System > IPv6 Neighbor Settings
The user can configure the Switch’s IPv6 neighbor settings. The Switch’s current IPv6 neighbor settings will be displayed in the table at the bottom of this window.
Figure 5.22 – System > IPv6 Neighbor Settings
Interface Name: Enter the interface name of the IPv6 neighbor.
Neighbor IPv6 Address: Specifies the neighbor IPv6 address.
Link Layer MAC Address: Specifies the link layer MAC address.
Click Apply for the settings to take effect.
Interface Name: Specifies the interface name of the IPv6 neighbor. To search for all the current interfaces on the Switch, go to the second Interface Name field in the middle part of the window, tick the All check box.
Tick the Hardware option to display all the neighbor cache entries which were written into the hardware table.
State: Use the drop-down menu to select All, Address, Static or Dynamic. When the user selects address from the drop-down menu, the user will be able to enter an IP address in the space provided next to the state option.
Click Find to locate a specific entry based on the information entered.
Click Clear to clear all the information entered in the fields.
System > Password
Setting a password is a critical tool for managers to secure the Web-Smart Switch. After entering the old password and the new password twice, click Apply for the changes to take effect.
3 1
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.23 – System > Password Access Control
System > Port Settings
In the Port Setting page, the status of all ports can be monitored and adjusted for optimum configuration. By selecting a range of ports (From Port and To Port), the Speed can be set for all selected ports by clicking
Apply. Press the Refresh button to view the latest information.
Figure 5.24 – System > Port Settings
Speed: Gigabit Fiber connections can operate in 1000M Full Force Mode, Auto Mode or Disabled. Copper connections can operate in Forced Mode settings (1000M Full, 100M Full, 100M Half, 10M Full, 10M Half),
Auto, or Disabled. 100M Fiber connections support 100M Full Force Mode, 100M Half Force Mode, or
Disabled. The default setting for all ports is Auto.
NOTE: Be sure to adjust port speed settings appropriately after changing the connected cable media types.
MDI/MDIX:
A medium dependent interface (MDI) port is an Ethernet port connection typically used on the Network
Interface Card (NIC) or Integrated NIC port on a PC. Switches and hubs usually use Medium dependent
interface crossover (MDIX) interface. When connecting the Switch to end stations, user have to use straight through Ethernet cables to make sure the Tx/Rx pairs match up properly. When connecting the
Switch to other networking devices, a crossover cable must be used.
This switch provides a configurable MDI/MDIX function for users. The switches can be set as an MDI port in order to connect to other hubs or switches without an Ethernet crossover cable.
Auto MDI/MDIX is designed on the switch to detect if the connection is backwards, and automatically chooses MDI or MDIX to properly match the connection. The default setting is “Auto” MDI/MDIX.
Flow Control: You can enable this function to mitigate the traffic congestion. Ports configured for full-duplex use 802.3x flow control, half-duplex ports use backpressure flow control. The default setting is Disabled.
Link Status: Reporting Down indicates the port is disconnected.
System > DHCP Auto Configuration
This page allows you to enable the DHCP Auto Configuration feature on the Switch. When enabled, the
Switch becomes a DHCP client and gets the configuration file from a TFTP server automatically on next boot up. To accomplish this, the DHCP server must deliver the TFTP server IP address and configuration file name information in the DHCP reply packet. The TFTP server must be up and running and store the necessary configuration file in its base directory when the request is received from the Switch.
32
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.25 – System > DHCP Auto Configuration
System > SysLog Host
System Logs record and manage events, as well as report errors and informational messages. Message severity determines a set of event messages that will be sent. Click Enable so you can start to configure the related settings of the remote system log server, then press Apply for the changes to take effect
Figure 5.26 – System > SysLog Host Settings
Server IP Address: Select IPv4 or IPv6 then specify the IP address of the system log server.
UDP Port: Specifies the UDP port to which the server logs are sent. The possible range is 1 – 65535, and the default value is 514.
Time Stamp: Select Enable to time stamp log messages.
Severity: Specifies the minimum severity from which warning messages are sent to the server. There are three levels. When a severity level is selected, all severity level choices above the selection are selected automatically. The possible levels are:
Warning - The lowest level of a device warning. The device is functioning, but an operational problem has occurred.
Informational - Provides device information.
All - Displays all levels of system logs.
Facility: Specifies an application from which system logs are sent to the remote server. Only one facility can be assigned to a single server. If a second facility level is assigned, the first facility is overwritten. There are up to eight facilities can be assigned (Local 0 ~ Local 7).
System > Time Profile
The Time Profile page allows users to configure the time profile settings of the device.
Figure 5.27 – System > Time Profile
Profile Name: Specifies the profile name.
Time(HH MM): Specifies the Start Time and End Time.
Weekdays: Specifies the work day.
3 3
5 Configuration
D-Link Web Smart Switch User Manual
Date: Select Date and specifies the From Day and To Day of the time profile.
Click Add to create a new time profile or click Delete to delete a time profile from the table.
System > Power Saving
The Power Saving mode feature reduces power consumption automatically when the RJ-45 port is link down or the connected devices are turned off. Less power will be consumed also when the short cable is used
(less than 20 meters).
By reducing power consumption, less heat is produced, resulting in extended product life and lower operating costs. By default, the Cable Length Detection and Link Status Detection are enabled. Click Apply to make the change effective.
Figure 5.28 – System > Power Saving
Advanced Power Saving Settings:
Type: Specifies the Power Saving type to be LED Shut-off, Port Shut-off, Port Standby or System
Hibernation.
LED Shut-off - The LED Shut-off gets high priority. If the user select LED Shut-off, the profile function will not take effect. It means the LED can not be turned on after Time Profile time’s up when the state is disabled. On the contrary, if the LED is enabled, the Time Profile function will work.
Port Shut-off - The Port Shut-off state has high priority (the priority rule is the same as LED.)
Therefore, if the Port Shut-off sate is already disabled the Time Profile function will not take effect.
Port Standby - The system changes to standby state and wait for a wake up event. Each port on the system enters sleep state by schedule.
System Hibernation - In this mode, switches get most power-saving figures since main chipsets
(both MAC and PHY) are disabled for all ports, and energy required to power the CPU is minimal.
State: Specifies the power saving state to be Enabled or Disabled.
Time Profile 1: Specifies the time profile or None.
Time Profile 2: Specifies the time profile or None.
Port: Specifies the ports to be configure of the Power Saving.
Click Select All configure all ports, or click Clear to uncheck all port. Then click Apply to implement changes made.
System > IEEE802.3az EEE Settings
The IEEE 802.3 EEE standard defines mechanisms and protocols intended to reduce the energy consumption of network links during periods of low utilization, by transitioning interfaces into a low-power state without interrupting the network connection. The transmitted and received sides should be
34
5 Configuration
D-Link Web Smart Switch User Manual
IEEE802.3az EEE compliance. By default, the switch enabled the 802.3az EEE function. Users can disable this feature by individual port via the IEEE802.3az EEE setting page.
Figure 5.29 – System > IEEE802.3az EEE Settings
From Port / To Port: A consecutive group of ports may be configured starting with the selected port.
State: Enabled or Disabled the IEEE802.3az EEE for the specified ports. By default, all ports are enabled.
Click Apply to implement changes made.
If the connection speed drops down from 1000M to 100M, or the first link up takes longer time, please follow below steps and check again:
1. Upgrade drivers of your Ethernet adapter or LAN controller for the host PC.
2. Disable EEE function on the switch port.
VLAN > 802.1Q VLAN
A VLAN is a group of ports that can be anywhere in the network, but communicate as though they were in the same area.
VLANs can be easily organized to reflect department groups (such as R&D, Marketing), usage groups (such as e-mail), or multicast groups (multimedia applications such as video conferencing), and therefore help to simplify network management by allowing users to move devices to a new VLAN without having to change any physical connections.
The IEEE 802.1Q VLAN Configuration page provides powerful VID management functions. The original settings have the VID as 1, no default name, and all ports as “Untagged”
Rename: Click to rename the VLAN group.
Delete VID: Click to delete the VLAN group.
Add New VID: Click to create a new VID group, assigning ports from 01 to 28 as Untag, Tag, or Not
Member. A port can be untagged in only one VID. To save the VID group, click Apply.
You may change the name accordingly to the desired groups, such as R&D, Marketing, email, etc.
Figure 5.30 – Configuration > 802.1Q VLAN
3 5
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.31 – Configuration > 802.1Q VLAN > Add VLAN
VLAN > 802.1Q VLAN PVID
The 802.1Q VLAN PVID setting allows user to configure the PVID for each ports. Click Apply to implement changes made.
Figure 5.32 – Configuration > 802.1Q VLAN PVID
VLAN > 802.1Q Management VLAN
The 802.1Q Management VLAN setting allows user to transfer the authority of the switch from the default
VLAN to others created by users. This allows managing the whole network more flexible.
By default, the Management VLAN is disabled. You can select any existing VLAN as the management VLAN when this function is enabled. There can only be one management VLAN at a time.
Figure 5.33 – Configuration > 802.1Q Management VLAN
VLAN > Voice VLAN > Voice VLAN Global Settings
Voice VLAN is a feature that allows you to automatically place the voice traffic from IP phone to an assigned
VLAN to enhance the VoIP service. With a higher priority and individual VLAN, the quality and the security of
VoIP traffic are guaranteed. If a VoIP packet comes with a VLAN tag, the Voice VLAN function won’t replace the original VLAN tag.
Figure 5.34 – VLAN > Voice VLAN > Voice VLAN Global Settings
36
5 Configuration
D-Link Web Smart Switch User Manual
Voice VLAN: Select to enable or disable Voice VLAN. The default is Disabled. After you enabled Voice
VLAN, you can configure the Voice VLAN Global Settings.
VLAN ID: The ID of VLAN that you want to assign voice traffic to. You must first create a VLAN from the
802.1Q VLAN page before you can assign a dedicated Voice VLAN. The member port you configured in
802.1Q VLAN setting page will be the static member port of voice VLAN. To dynamically add ports into the voice VLAN, please enable the Auto Detection function
Priority: The 802.1p priority levels of the traffic in the Voice VLAN.
Aging Time (1-120): Enter a period of time (in hours) to remove a port from the voice VLAN if the port is an automatic VLAN member. When the last voice device stops sending traffic and the MAC address of this voice device is aged out, the voice VLAN aging timer will start. The port will be removed from the voice VLAN after the expiration of the voice VLAN aging timer. Selectable range is from 1 to 120 hours, and default is 1.
Click Apply to implement changes made.
Voice VLAN OUI Settings: This allows the user to configure the user-defined voice traffic’s OUI. An
Organizationally Unique Identifier (OUI) is the first three bytes of the MAC address. This identifier uniquely identifies a vendor, manufacturer, or other organization.
There are some pre-defined OUIs and when the user configures personal OUI, these pre-defined OUIs must be avoided. Below are the pre-defined voice traffic’s OUI:
OUI Vendor
00:E0:BB 3Com
Mnemonic Name
3com
00:03:6B
00:E0:75
00:D0:1E
00:01:E3
Cisco
Veritel
Pingtel
Siemens cisco veritel pingtel siemens
00:60:B9
00:0F:E2
NEC/ Philips nec&philips
Huawei-3COM huawei&3com
00:09:6E Avaya avaya
Default OUI: Pre-defined OUI values, including brand names of 3COM, Cisco, Veritel, Pingtel, Siemens,
NEC/Philips, Huawei3COM, and Avaya.
User defined OUI: You can manually create a Telephony OUI with a description. The maximum number of user defined OUIs is 10. It will occupy one ACL rule when selecting a user defined OUI by default, and to configure one user-defined OUI will take extra one ACL rule. System will auto generate an ACL profile
(Profile ID: 51) for all the Voice VLAN rules.
Select the OUI and press Add to the lower table to complete the Auto Voice VLAN setting.
Note: Voice VLAN has higher priority than any other features (including QoS). Therefore the voice traffic will be operated according to the
Voice VLAN setting and not impacted by the QoS feature.
Note: It is recommended setting the highest priority for Voice VLAN to guarantee the quality of
VoIP traffic.
3 7
5 Configuration
D-Link Web Smart Switch User Manual
VLAN > Voice VLAN > Voice VLAN Port Settings
The Voice VLAN Port Settings page allows users to automatically place the voice traffic from IP phone to an assigned VLAN to enhance the VoIP service. With a higher priority and individual VLAN, the quality and the security of VoIP traffic are guaranteed.
Figure 5.35 – VLAN > Voice VLAN > Voice VLAN Port Settings
From Port / To Port: A consecutive group of ports may be configured starting with the selected port.
Auto Detection: Switch will add ports to the voice VLAN automatically if it detects the device OUI matches
the Telephony OUI configured in Voice VLAN OUI Setting page. Use the drop-down menu to enable or
disable the OUI auto detection function. The default is Disabled
Tagged / Untagged: tagged or untagged the ports.
Click Apply to implement changes made and Refresh to refresh the voice vlan table.
Note: Voice VLAN has higher priority than any other features even QoS. Therefore the voice traffic will be operated according to Voice VLAN setting and not impacted by QoS feature.
Note: It is recommended setting the highest priority for Voice VLAN to guarantee the quality of
VoIP traffic.
VLAN > Voice VLAN > Voice Device List
The Voice Device List page displays the information of Voice VLAN.
Figure 5.36 – VLAN > Voice VLAN > Voice Device List
Select a port or all ports and click Search to display the Voice Device information in the table.
VLAN > Auto Surveillance VLAN Settings
Similar as Voice VLAN, Auto Surveillance VLAN is a feature that allows you to automatically place the video traffic from D-Link IP cameras to an assigned VLAN to enhance the IP surveillance service. With a higher priority and individual VLAN, the quality and the security of surveillance traffic are guaranteed. The Auto
Surveillance VLAN function will check the source MAC address / VLAN ID on the incoming packets. If it matches specified MAC address / VLAN ID, the packets will pass through switch with desired priority.
38
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.37 – VLAN > Auto Surveillance VLAN
Auto Surveillance VLAN Global Settings:
Auto Surveillance VLAN State: Select to enable or disable Auto Surveillance VLAN. The default is
Disabled.
VLAN ID: By default, the VLAN ID 4094 was created as Auto Surveillance VLAN. You also can create another Auto Surveillance VLAN by selecting a VLAN ID that you have created a VLAN from the 802.1Q
VLAN page. The member port you configured in 802.1Q VLAN setting page will be the static member port of
Auto Surveillance VLAN.
Priority: The 802.1p priority levels of the traffic in the Auto Surveillance VLAN. The possible values are
Highest, High, Medium and Low.
Tagged Uplink/Downlink Port: Specifies the ports to be tagged uplink port or downlink port for the Auto
Surveillance VLAN.
Click Apply to implement changes of Auto Surveillance VLAN global settings.
User-defined MAC Settings:
Component Type: Auto Surveillance VLAN will automatically detect D-Link Surveillance Devices by default.
There are another five surveillance components that could be configured to be auto-detected by the Auto
Surveillance VLAN. These five components are Video Management Server (VMS), VMS Client/Remote
viewer, Video Encoder, Network Storage and Other IP Surveillance Devices.
Description: Here to input the description for the component type.
MAC/OUI: You can manually create an MAC or OUI address for the surveillance component. The maximum number of user defined MAC address is 5. System will auto generate an ACL profile (Profile ID: 56) for all the
Auto Surveillance VLAN rules.
Click Add to create a new surveillance component and Refresh to refresh the Auto Surveillance VLAN summary table.
L2 Functions > Jumbo Frame
D-Link Gigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of
1536 bytes) of up to 10,000 bytes (tagged). Default is disabled, Select Enabled then click Apply to turn on the jumbo frame support.
3 9
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.38 – L2 Functions > Jumbo Frame
L2 Functions > Port Mirroring
Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port, where the packet can be studied. This enables network managers to better monitor network performances.
Figure 5.39 – L2 Functions > Port Mirroring
Selection options for the Source Ports are as follows:
TX (transmit) mode: Duplicates the data transmitted from the source port and forwards it to the Target Port.
Click “all” to include all ports into port mirroring.
RX (receive) mode: Duplicates the data that is received from the source port and forwards it to the Target
Port. Click “all” to include all ports into port mirroring.
TX/RX (transmit and receive) mode: Duplicate both the data transmitted from and data sent to the source port, and forwards all the data to the assigned Target Port. Click “all” to include all ports into port mirroring.
None: Turns off the mirroring of the port. Click “all” to remove all ports from mirroring.
L2 Functions > Loopback Detection
The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree
Protocol (STP) is not enabled in the network, especially when the down links are hubs or unmanaged switches. The Switch will automatically shutdown the port and sends a log to the administrator. The
Loopback Detection port will be unlocked when the Loopback Detection Recover Time times out. The
Loopback Detection function can be implemented on a range of ports at the same time. You may enable or disable this function using the pull-down menu.
Figure 5.40 – L2 Functions > Loopback Detection
Loopback Detection: Use the drop-down menu to enable or disable loopback detection. The default is
Disabled.
40
5 Configuration
D-Link Web Smart Switch User Manual
Mode: Specifies Port-based or VLAN-based mode. If port-based mode is selected, the loop happening port will be shut down and affect all member VLANs. If VLAN-based mode is selected, only the member port in the loop happening VLAN will be shut down
Interval (1-32767): Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds.
Recover Time (0 or 60-1000000): Time allowed (in seconds) for recovery when a Loopback is detected.
The Loop Detection Recover Time can be set at 0 seconds, or 60 to 1000000 seconds. Entering 0 will disable the Loop Detection Recover Time. The default is 60 seconds.
From Port: The beginning of a consecutive group of ports may be configured starting with the selected port.
To Port: The ending of a consecutive group of ports may be configured starting with the selected port.
State: Use the drop-down menu to toggle between Enabled and Disabled. Default is Disabled.
Click Apply to implement changes made or click Refresh to refresh the Loopback Detection table.
L2 Functions > MAC Address Table > Static MAC
This feature provides two distinct functions. The Disable Auto Learning table allows turning off the function of learning MAC address automatically, if a port isn't specified as an uplink port (for example, connects to a
DHCP Server or Gateway). By default, this feature is Off (disabled).
Figure 5.41 – L2 Functions > MAC Address Table > Static Mac Address
To initiate the removal of auto-learning for any of the uplink ports, click On to enable this feature, and then select the port(s) for auto learning to be disabled.
The Static MAC Address Lists table displays the static MAC addresses connected, as well as the VID.
Click Add to add a new MAC address, you also need to select the assigned Port number. Enter both the
Mac Address and VID, and then Click Add. Click Delete to remove one entry or click Delete all to clear the list.
By disabling Auto Learning capability and specifying the static MAC addresses, the network is protected from potential threats like hackers, because traffic from illegal MAC addresses will not be forwarded by the Switch.
L2 Functions > MAC Address Table > Dynamic Forwarding Table
For each port, this table displays the MAC address learned by the Switch. To add a MAC address to the
Static Mac Address List, click the Add checkbox, and then click Apply associated with the identified address.
Figure 5.42 – L2 Functions > MAC Address Table > Dynamic Forwarding Table
L2 Functions > Spanning Tree > STP Global Settings
The Switch implements two versions of the Spanning Tree Protoco l, the Rapid Spanning Tree
Protocol (RSTP) as defined by the IEEE 802.1w specification and a version compatible with the IEEE 802.1D
4 1
5 Configuration
D-Link Web Smart Switch User Manual
STP. RSTP can operate with legacy equipment implementing IEEE 802.1D, however the advantages of using RSTP will be lost.
The IEEE 802.1w Rapid Spanning Tree Protocol (RSTP) evolved from the 802.1D STP standard. RSTP was developed in order to overcome some limitations of STP that impede the function of some recent switching innovations. The basic function and much of the terminology is the same as STP. Most of the settings configured for STP are also used for RSTP. This section introduces some new Spanning Tree concepts and illustrates the main differences between the two protocols.
By default, Rapid Spanning Tree is disabled. If enabled, the Switch will listen for BPDU packets and its accompanying Hello packet. BPDU packets are sent even if a BPDU packet was not received. Therefore, each link between bridges is sensitive to the status of the link. Ultimately this difference results in faster detection of failed links, and thus faster topology adjustment.
After enabling STP, setting the STP Global Setting includes the following options:
Figure 5.43 – L2 Functions > Spanning Tree > STP Global Settings
STP Version: You can choose RSTP or STP Compatible. The default setting is RSTP.
Bridge Priority: This value between 0 and 61410 specifies the priority for forwarding packets: the lower the value, the higher the priority. The default is 32768.
TX Hold Count (1-10): Used to set the maximum number of Hello packets transmitted per interval. The count can be specified from 1 to 10. The default is 6.
Maximum Age (6-40 sec): This value may be set to ensure that old information does not endlessly circulate through redundant paths in the network, preventing the effective propagation of the new information. Set by the Root Bridge, this value will aid in determining that the Switch has spanning tree configuration values consistent with other devices on the bridged LAN. If the value ages out and a BPDU has still not been received from the Root Bridge, the Switch will start sending its own BPDU to all other switches for permission to become the Root Bridge. If it turns out that the Switch has the lowest Bridge Identifier, it will become the
Root Bridge. A time interval may be chosen between 6 and 40 seconds. The default value is 20. (Max Age has to have a value bigger than Hello Time)
Hello Time (1-10 sec): The user may set the time interval between transmissions of configuration messages by the root device, thus stating that the Switch is still functioning. The default is 2 seconds.
Forward Delay (4-30 sec): This sets the maximum amount of time that the root device will wait before changing states. The default is 15 seconds.
Root Bridge: Displays the MAC address of the Root Bridge.
Root Cost: Display the cost of the Root Bridge.
Root Maximum Age: Displays the Maximum Age of the Root Bridge.
Root Forward Delay: Displays the Forward Delay of the Root Bridge.
Root port: Displays the root port.
Click Apply for the settings to take effect. Click Refresh to renew the page.
42
5 Configuration
D-Link Web Smart Switch User Manual
L2 Functions > Spanning Tree > STP Port Settings
STP can be set up on a port per port basis. In addition to setting Spanning Tree parameters for use on the switch level, the Switch allows for the configuration of the groups of ports, each port-group of which will have its own spanning tree, and will require some of its own configuration settings.
An STP Group spanning tree works in the same way as the switch-level spanning tree, but the root bridge concept is replaced with a root port concept. A root port is a port of the group that is elected based on port priority and port cost, to be the connection to the network for the group. Redundant links will be blocked, just as redundant links are blocked on the switch level.
The STP on the switch level blocks redundant links between switches (and similar network devices). The port level STP will block redundant links within an STP Group.
It is advisable to define an STP Group to correspond to a VLAN group of ports.
Figure 5.44 – L2 Functions > Spanning Tree > STP Port Settings
From Port/To Port: A consecutive group of ports may be configured starting with the selected port.
State: Use the drop-down menu to enable or disable STP by per-port based. It will be selectable after the global STP is enabled.
External Cost: This defines a metric that indicates the relative cost of forwarding packetsto the specified port list. Port cost can be set automatically or as a metric value. Thedefault value is 0 (auto).
0 (auto) - Setting 0 for the external cost will automatically s et the speed for forwarding packets to the specified port(s) in the list for optimal efficiency. Default port cost: 100Mbps port = 200000. Gigabit port = 20000.
Value 1-200000000 - Define a value between 1 and 200000000 to determine the external cost. The lower the number, the greater the probability the port will be chosen to forward packets.
Migrate: Setting this parameter as Yes will set the ports to send out BPDU packets to other bridges, requesting information on their STP setting. If the Switch is configured for RSTP, the port will be capable to migrate from 802.1d STP to 802.1w RSTP. Migration should be set as yes on ports connected to network stations or segments that are capable of being upgraded to 802.1w RSTP on all or some portion of the segment.
Edge: Selecting the True parameter designates the port as an edge port. Edge ports cannot create loops, however an edge port can lose edge port status if a topology change creates a potential for a loop. An edge port normally should not receive BPDU packets. If a BPDU packet is received, it automatically loses edge port status. Selecting the False parameter indicates that the port does not have edge port status. Selecting the Auto parameter indicates that the port have edge port status or not have edge port status automatically.
Priority: Specify the priority of each port. Selectable range is from 0 to 240, and the default setting is 128.
The lower the number, the greater the probability the port will be chosen as a root port.
P2P: Choosing the True parameter indicates a point-to-point (P2P) shared link. P2P ports are similar to edge ports, however they are restricted in that a P2P port must operate in full-duplex.
Like edge ports, P2P ports transition to a forwarding state rapidly thus benefiting from RSTP. A p2p value of
false indicates that the port cannot have p2p status. Auto allows the port to have p2p status whenever possible and operate as if the p2p status were true. If the port cannot maintain this status, (for example if the
4 3
5 Configuration
D-Link Web Smart Switch User Manual port is forced to half-duplex operation) the p2p status changes to operate as if the p2p value were False. The default setting for this parameter is Auto.
Restricted Role: Toggle between True and False to set the restricted role state of the packet. If set to True, the port will never be selected to be the Root port. The default value is False.
Restricted TCN: Toggle between True and False to set the restricted TCN of the packet. Topology Change
Notification (TCN) is a BPDU that a bridge sends out to its root port to signal a topology change. If set to
True, it stops the port from propagating received TCN and to other ports. The default value is False.
Click Apply for the settings to take effect. Click Refresh to renew the page.
L2 Functions > Link Aggregation > Port Trunking
The Trunking function enables the combining of two or more ports together to increase bandwidth. Up to eight Trunk groups may be created, and each group consists up to eight ports. Select the ports to be grouped together, and then click Apply to activate the selected Trunking groups. Two types of link aggregation can be selected:
Static - Static link aggregation.
LACP - LACP (Link Aggregation Control Protocol) is enabled on the device. LACP allows for the automatic detection of links in a Port Trunking Group.
Disable - Remove all members in this trunk group.
Figure 5.45 – L2 Functions > Link Aggregation > Port Trunking
NOTE: Each combined trunk port must be connected to devices within the same VLAN group.
L2 Functions > Link Aggregation > LACP Port Settings
The LACP Port Settings is used to create port trunking groups on the Switch. The user may set which ports will be active and passive in processing and sending LACP control frames.
Figure 5.46 – L2 Functions > Link Aggregation > LACP Port Settings
From Port: The beginning of a consecutive group of ports may be configured starting with the selected port.
44
5 Configuration
D-Link Web Smart Switch User Manual
To Port: The ending of a consecutive group of ports may be configured starting with the selected port.
Activity: There are two different roles of LACP ports:
Active - Active LACP ports are capable of processing and sending LACP control frames. This allows
LACP compliant devices to negotiate the aggregated link so the group may be changed dynamically as needs require. In order to utilize the ability to change an aggregated port group, that is, to add or subtract ports from the group, at least one of the participating devices must designate LACP ports as active. Both devices must support LACP.
Passive - LACP ports that are designated as passive cannot initially send LACP control frames. In order to allow the linked port group to negotiate adjustments and make changes dynamically, one end of the connection must have "active" LACP ports.
Timeout: Specify the administrative LACP timeout. The possible field values are:
Short (3 Sec) - Defines the LACP timeout as 3 seconds.
Long (90 Sec) - Defines the LACP timeout as 90 seconds. This is the default value.
Click Apply to implement the changes made.
L2 Functions > Multicast > IGMP Snooping
With Internet Group Management Protocol (IGMP) snooping, the Web Smart Switch can make intelligent multicast forwarding decisions by examining the contents of each frame’s Layer 2 MAC header.
IGMP snooping can help reduce cluttered traffic on the LAN. With IGMP snooping enabled globally, the Web
Smart Switch will forward multicast traffic only to connections that have group members attached.
The settings of IGMP snooping is set by each VLAN individually.
Figure 5.47 – L2 Functions > Multicast > IGMP Snooping
By default, IGMP is disabled. If enabled, the IGMP Global Settings will need to be entered:
It is recommended to keep Report to all ports enable to ensure the functionality of SmartConsole Utility.
Host Timeout (130-153025 sec): This is the interval after which a learned host port entry will be purged. For each host port learned, a 'Port Purge Timer' runs for 'Host Port Purge Interval'. This timer will be restarted whenever a report message from host is received over that port. If no report messages are received for 'Host
Port Purge Interval' time, the learned host entry will be purged from the multicast group. The default value is
260 seconds.
Robustness Variable (2-255 sec): The Robustness Variable allows adjustment for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may need to be increased. The
Robustness Variable cannot be set to zero, and it SHOULD NOT be. Default is 2 seconds.
Query Interval (60-600 sec): The Query Interval is the interval between General Queries sent. By adjusting the Query Interval, the number of IGMP messages can be increased or decreased; larger values will cause
IGMP Queries to be sent less often. Default value is 125 seconds.
Router Timeout (60-600 sec): This is the interval after which a learned router port entry will be purged. For each router port learned, a 'Router Port Purge Timer' runs for 'Router Port Purge Interval'. This timer will be restarted whenever a Query control message is received over that port. If there are no Query control messages received for 'Router Port Purge Interval' time, the learned router port entry will be purged. Default is 260 seconds.
4 5
5 Configuration
D-Link Web Smart Switch User Manual
Last Member Query Interval (1-25 sec): The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages. This value may be adjusted to modify the "leave latency" of the network. A reduced value results in reduced time to detect the loss of the last member of a group. Default is 1 second.
Max Response Time (10-25 sec): The Max Response Time specifies the maximum allowed time before sending a responding report message. Adjusting this setting effects the "leave latency", or the time between the moment the last host leaves a group and when the multicast server is notified that there are no more members. It also allows adjustments for controlling the frequency of IGMP traffic on a subnet. Default is 10 seconds.
To enable IGMP snooping for a given VLAN, select enable and click on the Apply button. Then press the
Edit button under Router Port Setting, and select the ports to be assigned as router ports for IGMP snooping for the VLAN, and press Apply for changes to take effect. A router port configured manually is a
Static Router Port, and a Dynamic Router Port is dynamically configured by the Switch when query control message is received.
Figure 5.48 – L2 Functions > Multicast > IGMP Snooping VLAN Settings
State : Specify the State to be enabled or disabled.
Querier State: D-Link Smart Switch is able to send out the IGMP Queries to check the status of multicast clients. Default is disabled.
Fast Leave: Specify the Fast Leave feature to be enabled or disabled.
To view the Multicast Entry Table for a given VLAN, press the View button.
Figure 5.45 – L2 Functions > Multicast > IGMP Multicast Entry Table
Click Delete to remove a specified entry or click Delete All to remove all entries.
L2 Functions > Multicast > Multicast Forwarding
The Multicast Forwarding page displays all of the entries made into the Switch’s static multicast forwarding table. To implement the Multicast Forwarding Settings, input VID, Multicast MAC Address and port settings, then click Add.
46
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.49 – L2 Functions > Multicast > Multicast Forwarding
VID: The VLAN ID of the VLAN to which the corresponding MAC address belongs.
Multicast MAC Address: The MAC address of the static source of multicast packets. This must be a multicast MAC address.
Port Settings: Allows the selection of ports that will be members of the static multicast group and ports either that are forbidden from joining dynamically, or that can join the multicast group dynamically, using
GMRP.
Member - The port is a static member of the multicast group.
None - No restrictions on the port dynamically joining the multicast group. When None is chosen, the port will not be a member of the Static Multicast Group.
L2 Functions > Multicast > Multicast Filtering Mode
The Multicast Filtering Mode function allows users to select the filtering mode for IGMP group per VLAN basis.
Figure 5.50 – L2 Functions > Multicast > Multicast Filtering Mode
VLAN ID: Specifies the VLAN ID.
Filtering Mode:
Forward Unregistered Groups: The multicast stream will be forwarded based on the register table in registered group, but it will be flooded to all ports of the VLAN in unregistered group.
Filter Unregistered Groups: The registered group will be forwarded based on the register table and the unregister group will be filtered.
Click Apply to make the change effective.
L2 Functions > SNTP > Time Settings
SNTP or Simple Network Time Protocol is used by the Switch to synchronize the clock of the computer. The
SNTP settings folders contain two windows: Time Settings and TimeZone Settings. Users can configure the time settings for the switch, and the following parameters can be set or are displayed in the Time Settings page.
4 7
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.51 – L2 Functions > SNTP > Time Settings
Clock Source: Specify the clock source by which the system time is set. The possible options are:
Local - Indicates that the system time is set locally by the device.
SNTP - Indicates that the system time is retrieved from a SNTP server.
Current Time: Displays the current date and time for the switch.
If choosing SNTP for the clock source, then the following parameters will be available:
SNTP First Server: Select IPv4 or IPv6 and specify the IP address of the primary SNTP server from which the system time is retrieved.
SNTP Second Server: Select IPv4 or IPv6 and specify the IP address of the secondary SNTP server from which the system time is retrieved.
SNTP Poll Interval in Seconds (30-99999): Defines the interval (in seconds) at which the SNTP server is polled for Unicast information. The Poll Interval default is 30 seconds.
Click Apply to implement changes made.
When selecting Local for the clock source, users can select from one of two options:
Manually set current time: Users input the system time manually.
Set time from PC: The system time will be synchronized from the local computer.
L2 Functions > SNTP > TimeZone Settings
The TimeZone Setting Page is used to configure time zones and Daylight Savings time settings for SNTP.
Figure 5.52 – L2 Functions > SNTP > TimeZone Settings
Daylight Saving Time State: Enable or disable the DST Settings.
Daylight Saving Time Offset: Use this drop-down menu to specify the amount of time that will constitute your local DST offset - 30, 60, 90, or 120 minutes.
48
5 Configuration
D-Link Web Smart Switch User Manual
Time Zone Offset GMT +/- HH:MM: Use these drop-down menus to specify your local time zone's offset from Greenwich Mean Time (GMT.)
Daylight Saving Time Settings:
From: Month / Day: Enter the month DST and date DST will start on, each year.
From: HH:MM: Enter the time of day that DST will start on, each year.
To: Month / Day: Enter the month DST and date DST will end on, each year.
To: HH:MM: Enter the time of day that DST will end on, each year.
Click Apply to implement changes made.
L2 Functions > LLDP > LLDP Global Settings
LLDP (Link Layer Discovery Protocol) provides IEEE 802.1AB standards-based method for switches to advertise themselves to neighbor devices, as well as to learn about neighbor LLDP devices. SNMP utilities can learn the network topology by obtaining the MIB information in each LLDP device. The LLDP function is enabled by default.
Figure 5.53 – L2 Functions > LLDP > LLDP Global Settings
LLDP: When this function is Enabled, the switch can start to transmit, receive and process the LLDP packets.
For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports.
For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table. Click Apply to make the change effective.
Message TX Hold Multiplier (2-10): This parameter is a multiplier that determines the actual TTL value used in an LLDPDU. The default value is 4.
Message TX Interval (5-32768): This parameter indicates the interval at which LLDP frames are transmitted on behalf of this LLDP agent. The default value is 30 seconds.
LLDP ReInit Delay (1-10): This parameter indicates the amount of delay from the time adminStatus becomes "disabled" until re-initialization is attempted. The default value is 2 seconds.
LLDP TX Delay (1-8192): This parameter indicates the delay between successive LLDP frame transmissions initiated by value or status changes in the LLDP local systems MIB. The value for txDelay is set by the following range formula: 1 < txDelay < (0.25 °— msgTxInterval). The default value is 2 seconds.
L2 Functions > LLDP > LLDP MED Settings
By selecting a range of ports (From Port and To Port), the power PSE TLV type can be enabled for all selected ports to indicate the power source equipment (PSE) switch to transmit high power (15.4 to 30 Watts) to the pre-standard of 802.3at power devices via LLDP MDI TLV. Through this feature, the PSE can provide precise output power to the pre-standard of 802.3at power devices and achieve optimal power management.
4 9
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.54 – L2 Functions > LLDP > LLDP MED Settings
L2 Functions > LLDP > LLDP Port Settings
The Basic LLDP Port Settings page displays LLDP port information and contains parameters for configuring
LLDP port settings.
Figure 5.55 – L2 Functions > LLDP > LLDP Port Settings
From Port/ To Port: A consecutive group of ports may be configured starting with the selected port.
Notification State: Specifies whether notification is sent when an LLDP topology change occurs on the port.
The possible field values are:
Enabled – Enables LLDP notification on the port.
Disabled – Disables LLDP notification on the port. This is the default value.
Admin Status: Specifies the LLDP transmission mode on the port. The possible field values are:
TX_Only – Enables transmitting LLDP packets only.
RX_Only – Enables receiving LLDP packets only.
TX_and_RX – Enables transmitting and receiving LLDP packets. This is the default.
Disabled – Disables LLDP on the port.
Port Description: Specifies whether the Port Description TLV is enabled on the port. The possible field values are:
Enabled – Enables the Port Description TLV on the port.
Disabled – Disables the Port Description TLV on the port.
System Name: Specifies whether the System Name TLV is enabled on the port. The possible field values are:
Enabled – Enables the System Name TLV on the port.
Disabled – Disables the System Name TLV on the port.
System Description: Specifies whether the System Description TLV is enabled on the port. The possible field values are:
Enabled – Enables the System Description TLV on the port.
Disabled – Disables the System Description TLV on the port.
System Capabilities: Specifies whether the System Capabilities TLV is enabled on the port. The possible field values are:
Enabled – Enables the System Capabilities TLV on the port.
50
5 Configuration
D-Link Web Smart Switch User Manual
Disabled – Disables the System Capabilities TLV on the port.
Define these parameter fields. Click Apply to implement changes made and click Refresh to refresh the table information.
L2 Functions > LLDP > 802.1 Extension TLV
This 802.1 Extension TLV page is used to configure the LLDP Port settings.
Figure 5.56 – L2 Functions > LLDP > 802.1 Extension TLV Port Settings
From Port / To Port : A consecutive group of ports may be configured starting with the selected port.
Port VLAN ID : Specifies the Port VLAN ID to be enabled or disabled.
VLAN Name : Specifies the VLAN name to be enabled or disabled in the LLDP port. If select Enabled, users can specifies the content of VLAN ID or VLAN Name or all.
Protocol Identity : Specifies the Protocol Identity to be enabled or disabled in the LLDP port. If select
Enabled, users can specifies the EAPOL, LACP, GVRP, STP or ALL.
Click Apply to implement changes made and click Refresh to refresh the table information.
L2 Functions > LLDP > 802.3 Extension TLV
The 802.3 Extension LLDP Port Settings page displays 802.3 Extension LLDP port information and contains parameters for configuring 802.3 Extension LLDP port settings.
Figure 5.57 – L2 Functions > LLDP > 802.3 Extension TLV Port Settings
From Port/To Port: A consecutive group of ports may be configured starting with the selected port.
MAC/PHY Configuration/Status: Specifies whether the MAC/PHY Configuration Status is enabled on the port. The possible field values are:
Enabled – Enables the MAC/PHY Configuration Status on the port.
Disabled – Disables the MAC/PHY Configuration Status on the port.
5 1
5 Configuration
D-Link Web Smart Switch User Manual
Power via MDI: Advertises the Power via MDI implementations supported by the port. The possible field values are:
Enabled – Enables the Power via MDI configured on the port.
Disabled – Disables the Power via MDI configured on the port.
Link Aggregation: Specifies whether the link aggregation is enabled on the port. The possible field values are:
Enabled – Enables the link aggregation configured on the port.
Disabled – Disables the link aggregation configured on the port.
Maximum Frame Size: Specifies whether the Maximum Frame Size is enabled on the port. The possible field values are:
Enabled – Enables the Maximum Frame Size configured on the port.
Disabled – Disables the Maximum Frame Size configured on the port.
Define these parameter fields. Click Apply to implement changes made and click Refresh to refresh the table information.
L2 Functions > LLDP > LLDP Management Address Settings
The LLDP Management Address Settings allows the user to set management address which is included in
LLDP information transmitted.
Figure 5.58 – L2 Functions > LLDP > LLDP Management Address Settings
From Port/To Port: A consecutive group of ports may be configured starting with the selected port.
Address Type: Specify the LLDP address type on the port. The value is always IPv4.
Address: Specify the address.
Port State: Specify whether the Port State is enabled n the port. The possible field values are:
Enabled – Enables the port state configured on the port.
Disabled – Disables the port state configured on the port.
Click Apply to implement changes made.
L2 Functions > LLDP > LLDP Management Address Table
The LLDP Management Address Table page displays the detailed management address information for the entry.
Figure 5.59 – L2 Functions > LLDP > LLDP Management Address Table
52
5 Configuration
D-Link Web Smart Switch User Manual
Management Address: Select IPv4 or IPv6 address and enter the IP address. Click Search and the table will update and display the values required.
Subtype: Displays the managed address subtype. For example, MAC address or IPv4 address.
Management Address: Displays the IP address.
IF Type: Displays the IF Type.
OID: Displays the SNMP OID.
Advertising Ports: Displays the advertising ports.
L2 Functions > LLDP > LLDP Local Port Table
The LLDP Local Port Table page displays LLDP local port information.
Figure 5.60 – L2 Functions > LLDP > LLDP Local Port Table
Port : Displays the port number.
Port ID Subtype: Displays the port ID subtype.
Port ID: Displays the port ID (Unit number/Port number).
Port Description: Displays the port description.
Click View of Normal column to display more information.
Figure 5.61 – L2 Functions > LLDP > LLDP Local Port Normal Table
Click View of Detailed column to display detail information.
5 3
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.62 – L2 Functions > LLDP > LLDP Local Port Detailed Table
L2 Functions > LLDP > LLDP Remote Port Table
This LLDP Remote Port Table page is used to display the LLDP Remote Port Brief Table. Select port number and click Search to display additional information.
Figure 5.63 – L2 Functions > LLDP > LLDP Remote Port Table
To view the settings for a remote port, click View Normal and the following page displays.
54
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.64 – L2 Functions > LLDP > LLDP Remote Port Normal Table
To view the detail settings for a remote port, click View Detailed and the following page displays.
Figure 5.65 – L2 Functions > LLDP > LLDP Remote Port Detailed Table
L2 Functions > LLDP > LLDP Statistics
The LLDP Statistics page displays an overview of all LLDP traffic.
5 5
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.66 – L2 Functions > LLDP > LLDP Statistics
The following information can be viewed:
LLDP Statistics System: Displays the counters that refer to the whole switch.
Last Change Time – Displays the time for when the last change entry was last deleted or added. It is also displays the time elapsed since last change was detected.
Number of Table Insert – Displays the number of new entries inserted since switch reboot.
Number of Table Delete – Displays the number of new entries deleted since switch reboot.
Number of Table Drop – Displays the number of LLDP frames dropped due to that the table was full.
Number of Table Age Out – Displays the number of entries deleted due to Time-To-Live expiring.
LLDP Port Statistics: Displays the counters that refer to the ports.
TxPort FramesTotal – Displays the total number of LLDP frames transmitted on the port.
RxPort FramesDiscarded – Displays the total discarded frame number of LLDP frames received on the port.
RxPort FramesErrors – Displays the Error frame number of LLDP frames received on the port.
RxPort Frames – Displays the total number of LLDP frames received on the port.
RxPortTLVsDiscarded – Each LLDP frame can contain multiple pieces of information, known as
TLVs. If a TLV is malformed, it is counted and discarded.
RxPortTLVsUnrecognized – Displays the number of well-formed TLVs, but with an known type value.
RxPort Ageouts – Each LLDP frame contains information about how long time the LLDP information is valid. If no new LLDP frame is received within the age out time, the LLDP information is removed, and the Age-Out counter is incremented.
Click Refresh to renew the page, and click Clear to clean out all statistics.
QoS > Bandwidth Control
The Bandwidth Control page allows network managers to define the bandwidth settings for a specified port’s transmitting and receiving data rates.
56
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.67 – QoS > Bandwidth Control
From Port / To Port: A consecutive group of ports may be configured starting with the selected port.
Type: This drop-down menu allows you to select between RX (receive), TX (transmit), and Both. This setting will determine whether the bandwidth ceiling is applied to receiving, transmitting, or both receiving and transmitting packets.
No Limit: This drop-down menu allows you to specify that the selected port will have no bandwidth limit.
Enabled disables the limit.
Rate (64-1024000): This field allows you to enter the data rate, in Kbits per second, will be the limit for the selected port. The value is between 64 and 1024000.
Click Apply to set the bandwidth control for the selected ports.
QoS > 802.1p/DSCP/ToS
QoS is an implementation of the IEEE 802.1p standard that allows network administrators to reserve bandwidth for important functions that require a larger bandwidth or that might have a higher priority, such as
VoIP (voice-over Internet Protocol), web browsing applications, file server applications or video conferencing.
Thus with larger bandwidth, less critical traffic is limited, and therefore excessive bandwidth can be saved.
The following figure displays the status of Quality of Service priority levels of each port, higher priority means the traffic from this port will be first handled by the switch. For packets that are untagged, the switch will assign the priority depending on your configuration.
Figure 5.68 – QoS > 802.1p/DSCP/ToS
Select QoS Mode: Specifies the QoS mode to be 802.1p, DSCP or ToS.
Queuing Mechanism:
Strict Priority: Denoting a Strict scheduling will set the highest queue to be emptied first while the other queues will follow the weighted round-robin scheduling scheme
5 7
5 Configuration
D-Link Web Smart Switch User Manual
WRR: Use the weighted round-robin (
WRR) algorithm to handle packets in an even distribution in priority classes of service.
Click Apply for the settings to take effect.
From Port / To Port: Defines the port range which the port packet priorities are defined.
Priority: Defines the priority assigned to the port. The priorities are Highest, High, Medium and Low.
Click Apply for the settings to take effect.
QoS > IPv6 Traffic Class Priority Settings
The IPv6 Traffic Class Priority Settings page allows user to configure the priority of traffic class.
Figure 5.69 – QoS > IPv6 Traffic Class Priority Settings
IPv6 Traffic Class (0-255): Specify the value of IPv6 class.
Priority: Defines the priority assigned to the port. The priorities are Highest, High, Medium and Low.
Click Apply for the settings to take effect.
QoS > TCP/UDP Port Priority Settings
The TCP/UDP Port Priority Settings page allows user to configure the port priority.
Figure 5.70 – QoS > TCP/UDP Port Priority Settings
TCP/UDP: Specify port priority of TCP or UDP to be configured.
TCP/UDP Port (0-65535): Specify the TCP or UDP port.
Priority: Defines the priority assigned to the port. The priorities are Highest, High, Medium and Low.
Click Apply for the settings to take effect.
Security > Trusted Host
Use Trusted Host function to manage the switch from a remote station. You can enter up to ten designated management stations networks by defining the IPv4 Address/Netmask or IPv6 Address/Prefix as seen in the figure below. The first thing after the function is enabled is to add your local host IP address as a trusted host.
Otherwise, you may lose the connection.
Figure 5.71 Security > Trusted Host
58
5 Configuration
D-Link Web Smart Switch User Manual
Trusted Host: Specify the Trusted Host to be enabled or disabled. The default is disabled.
To define a management station IP setting, click the Add button and type in the IP address and Subnet mask.
Click the Apply button to save your settings. You may permit only single or a range of IP addresses by different IP mask setting, the format can be either 192.168.1.1/255.255.255.0 or 192.168.0.1/24. Please see the example below for permitting the IP range.
IP Address Subnet Mask Permitted IP
192.168.0.1 255.255.255.0 192.168.0.1~192.168.0.255
172.17.5.215 255.0.0.0 172.0.0.1~172.255.255.255
To delete the IP address simply click the Delete button, check the unwanted address, and then click Apply.
Security > Port Security
Port Security is a security feature that prevents unauthorized computers (with source MAC addresses) unknown to the Switch prior to stopping auto-learning processing from gaining access to the network.
A given ports’ (or a range of ports') dynamic MAC address learning can be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port lock is enabled. Using the drop-down menu, change Admin State to Enabled, input Max Learning Address, and then click Apply.
Figure 5.72 – Security > Port Security
Security > Traffic Segmentation
This feature provides administrators to limit traffic flow from a single port to a group of ports on a single
Switch. This method of segmenting the flow of traffic is similar to using VLANs to limit traffic, but is more restrictive.
Figure 5.73 – Security > Traffic Segmentation
5 9
5 Configuration
D-Link Web Smart Switch User Manual
Click Apply to enable or disable this feature.
To configure traffic segmentation specify a port or All ports from the switch, using the From Port pull-down menu and select To Port then click Apply to enter the settings into the Switch’s Traffic Segmentation table.
Click Select All button to check all ports or click Clear button to uncheck all ports.
Security > Safeguard Engine
D-Link’s Safeguard Engine is a robust and innovative technology that automatically throttles the impact of packet flooding into the switch's CPU. This function helps protect the Web-Smart Switch from being interrupted by malicious viruses or worm attacks. This option is enabled by default.
Figure 5.74 – Security > Safeguard Engine
Security > Storm Control
The Storm Control feature provides the ability to control the receive rate of broadcast, multicast, and unknown unicast packets. Once a packet storm has been detected, the Switch will drop packets coming into the Switch until the storm has subsided.
Figure 5.75 – Security > Storm Control
Storm Control Type: User can select the different Storm type from Broadcast Only, Multicast & Broadcast, and Multicast & Broadcast & Unknown Unicast.
Threshold (64Kbps * N): If storm control is enabled (default is disabled), the threshold is from of 64 ~
1,024,000 Kbit per second, with steps (N) of 64Kbps. N can be from 1 to 16000.
Click Apply for the settings to take effect.
Security > ARP Spoofing Prevention
ARP spoofing, also known as ARP poisoning, is a method to attack an Ethernet network by allowing an attacker to sniff data frames on a LAN, modifying the traffic, or stopping the traffic (known as a Denial of
Service – DoS attack). The main idea of ARP spoofing is to send fake or spoofed ARP messages to an
Ethernet network. It associates the attacker's or random MAC address with the IP address of another node such as the default gateway. Any traffic meant for that IP address would be mistakenly re-directed to the node specified by the attacker.
A common DoS attack today can be done by associating a nonexistent or specified MAC address to the IP address of the network’s default gateway. The malicious attacker only needs to broadcast one gratuitous
ARP to the network claiming to be the gateway, so that the whole network operation is turned down as all packets to the Internet will be directed to the wrong node.
The ARP Spoofing Prevention function can discard the ARP Spoofing Attack in the network by checking the gratuitous ARP packets and filtering those with illegal IP or MAC addresses.
60
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.76 – Security > ARP Spoofing Prevention
Enter the IP Address, MAC Address, Ports and then click Add to create a checking/filtering rule. Click
Delete to remove an existing rule and Delete All to clear all the entries.
Security > DHCP Server Screening
DHCP Server Screening function allows user to restrict the illegal DHCP server by discarding the DHCP service from distrusted ports. This page allows you to configure the DHCP Server Screening state for each port and designed trusted DHCP server IP address. Select Ports and then click Apply to enable or disable the function.
Figure 5.77 – Security > DHCP Server Screening
Trusted DHCP Server IP Settings: Select IPv4 or IPv6 and specify the IP address then click Apply to create
Trusted DHCP Server.
Click Add to add a DHCP trusted DHCP server.
Security > SSL Settings
Secure Sockets Layer (SSL) is a security feature that provides a secure communication path between a Web
Management host and the Switch Web UI by using authentication, digital signatures and encryption. These security functions are implemented by Ciphersuite, a security string that determines the cryptographic parameters, encryption algorithms and key sizes.
This page allows you to configure the SSL global state and the Ciphersuite settings. Select Enable or
Disable and then click Apply to change the SSL state or the Ciphersuite settings of the Switch. By default,
SSL is Disabled and all Ciphersuites are Enabled.
6 1
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.78 – Security > SSL Settings
NOTE: When SSL is enabled, it will take longer time to open a web page due to encryption. After saving configuration, please wait around 10 seconds for the system summery page.
Security > Smart Binding > Smart Binding Settings
The primary purpose of Smart Binding is to restrict client access to a switch by enabling administrators to configure pairs of client MAC and IP addresses that are allowed to access networks through a switch.
The Smart Binding function is port-based, meaning that a user can enable or disable the function on any individual port. Once Smart Binding is enabled on a switch port, the switch will restrict or allow client access by checking the pair of IP-MAC addresses with the pre-configured database, also known as the “IMPB white list”.
Users can enable or disable the Inspection packets and DHCP Snooping on the Switch.
Figure 5.79 – Security > Smart Binding > Smart Binding Settings
The Smart Binding Settings page contains the following fields:
From Port/ To Port: Select a range of ports to set for IP-MAC-port binding.
State: Use the drop-down menu to enable or disable these ports for Smart Binding.
Enabled –Enable Smart Binding with related configurations to the ports
Disabled –Disable Smart Binding.
Packet Inspection: Specifies ARP Inspection or IP+ARP Inspection for the IP packets. If ARP inspection is selected, the Switch will inspect incoming ARP packets and compare them with the Switch’s Smart Binding white list entries. If the IP-MAC pair of an ARP packet is not found in the white list, the Switch will block the
MAC address. A major benefit of Loose state is that it uses less CPU resources. However, it cannot block malicious users who send only unicast IP packets. An example of this is that a malicious user can perform
DoS attacks by statically configuring the ARP table on their PC. In this case, the Switch cannot block such attacks because the PC will not send out ARP packets. If ARP+ IP Inspection mode is selected, the Switch
62
5 Configuration
D-Link Web Smart Switch User Manual will inspect all incoming ARP and IP packets and compare them to the IMPB white list. If the IP-MAC pair find a match in the white list, the packets from that MAC address are unblocked. If not, the MAC address will stay blocked. While the mode examines every ingress ARP and IP packet, it enforces better security.
DHCP Snooping: By enable DHCP Snooping, the switch will snoop the packets sent from DHCP Server and clients, and update information to the White List.
Click Apply to make configurations make effects.
Security > Smart Binding > Smart Binding
The Smart Binding Settings page allows users to set IP-MAC-Port Binding entries by manually entering required information, or by scanning all connected devices and clicking to bind.
Figure 5.80 – Security > Smart Binding > Smart Binding
The Manual Binding Settings contains the following fields:
IP Address: Specifies the IP address to bind to the MAC address set below.
MAC Address: Specifies the MAC address to bind to the IP address set above.
Port: Specify the switch ports for which to configure this IP-MAC binding entry (IP Address + MAC Address).
Click Add to add a new entry.
Auto Scan: The Auto Scan Setting can list connected devices and easily select to bind. It contains the following fields:
IP Address From/To: Specifies the range of IP Address to find desired devices, or leaves the fields blank to see all connected devices.
Click Scan and the search results will be listed in below table.
Binding: check the box to select desired binding devices.
Apply: click Apply to set IP-MAC-Port Binding entries.”
Select All: to check the boxes of Binding for all found devices.
Clear All: to cancel the box of Binding
Security > Smart Binding > White List
When IP +ARP Inspection Mode is selected, the White List page displays finished IP-MAC-Port Binding entries from page Smart Binding. Only IP packets or ARP packets carrying matched IP-MAC-Port information can access to the switch. You can cancel a device’s authorization by deleting it from the table.
Figure 5.81 – Security > Smart Binding > White List
6 3
5 Configuration
D-Link Web Smart Switch User Manual
Select the check box of entry then click Delete to remove it.
Click Select All to select all entries of the table or click Clean to select none entries. Please keep at least one management host in the White List.
Security > Smart Binding > Black List
The Black List page shows unauthorized accesses. When ARP Inspection is selected and a device sends out an ARP packet containing unmatched IP-MAC-Port information, the device will be forbidden and listed here.
Figure 5.82 – Security > Smart Binding > Black List
By giving conditions, desired devices information can be screened out below and then click Find to search for a list of the entry:
VID: Enter the VLAN ID number of the device.
IP Address: Enter the IP Address of the device.
MAC Address: Enter the MAC Address of the device.
Port: Enter the port number which the device connects to.
Check a box of Delete column to release an entry from the forbidden list and then click Apply to delete an entry from the list.
Click Select All to select all entries, or click Clean to select none of the entries
AAA > 802.1X > 802.1X Settings
Network switches provide easy and open access to resources, by simply attaching a client PC. Unfortunately this automatic configuration also allows unauthorized personnel to easily intrude and possibly gain access to sensitive data.
IEEE-802.1X provides a security standard for network access control, especially in Wi-Fi wireless networks.
802.1X holds a network port disconnected until authentication is completed. The switch uses Extensible
Authentication Protocol over LANs (EAPOL) to exchange authentication protocol client identity (such as a user name) with the client, and forward it to another remote RADIUS authentication server to verify access rights. The EAP packet from the RADIUS server also contains the authentication method to be used. The client can reject the authentication method and request another, depending on the configuration of the client software and the RADIUS server. Depending on the authenticated results, the port is either made available to the user, or the user is denied access to the network.
The RADIUS servers make the network a lot easier to manage for the administrator by gathering and storing the user lists.
64
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.83 – Security > 802.1X > 802.1X Settings
By default, 802.1X is disabled. To use EAP for security, select enabled and set the 802.1X Global Settings for the Radius Server and applicable authentication information.
RADIUS Server IP: The IP address of the external Radius Server. You need to specify an RADIUS server to enable 802.1X authentication. Select IPv4 or IPv6 and specify the IP address.
Key: Masked password matching the Radius Server Key. The max. length is 32 characters.
Confirm Key: Enter the Key a second time for confirmation.
TxPeriod (1 – 65535 sec): This sets the TxPeriod of time for the authenticator PAE state machine. This value determines the period of an EAP Request/Identity packet transmitted to the client. Default is 24 seconds.
ReAuthEnabled: This function is to determine whether regular re-authentication will take place on this port(s). When the 802.1X function is enabled, the switch sends an EAP-request/identity packet to client. The
ReAuthEnabled function is by default disabled.
QuietPeriod (0 – 65535 sec): Sets the number of seconds that the switch remains in the quiet state following a failed authentication exchange with the client. Default is 60 seconds.
SuppTimeout (1 – 65535 sec): This value determines timeout conditions in the exchanges between the
Authenticator and the client. Default is 30 seconds.
ServerTimeout (1 – 65535 sec): Sets the amount of time the switch waits for a response from the client before resending the response to the authentication server. Default is 30 seconds.
MaxReq (1 – 10): This parameter specifies the maximum number of times that the switch retransmits an
EAP request (md-5challnege) to the client before it times out the authentication session. Default is 2 times.
ReAuthPeriod (1 – 4294967295 sec): This command affects the behavior of the switch only if periodic reauthentication is enabled. Default is 3600.
To establish 802.1X port-specific assignments, select the From Ports / To Ports and select Enable.
802.1X Port Access Control: Three type of Port Access Control State can be "Force Authorized", "Force
UnAuthorized" and "Auto".
Select Force Authorized to disable 802.1X and cause the port to transition to the authorized state without any authentication exchange required. This means the port transmits and receives normal traffic without
802.1X-based authentication of the client.
If Force Unauthorized is selected, the port will remain in the unauthorized state ignoring all attempts by the client to authenticate. The Switch cannot provide authentication services to the client through the interface.
If Auto is selected, it will enable 802.1X and cause the port to begin in the unauthorized state, allowing only
EAPOL frames to be sent and received through the port. The authentication process begins when the link
6 5
5 Configuration
D-Link Web Smart Switch User Manual state of the port transitions from down to up, or when an EAPOL-start frame is received. The Switch then requests the identity of the client and begins relaying authentication messages between the client and the authentication server. The default setting is Auto.
ACL > ACL Wizard
Access Control List (ACL) allows you to establish criteria to determine whether or not the Switch will forward packets based on the information contained in each packet's header. This criteria can be specified on a basis of the MAC address, or IP address.
The ACL Configuration Wizard will aid with the creation of access profiles and ACL Rules. The ACL Wizard will create the access rule and profile automatically. The maximum usable profiles are 50 and with 200 Rules in total for the switch. For DES-1210-52, the maximum usable profiles are 50 and with 450 Rules in total for the switch.
Figure 5.84 – ACL > ACL Wizard
From: Specify the origin of accessible packets. The possible values are:
Any - Indicates ACL action will take effect on packets from any source.
MAC Address - Indicates ACL action will be on packets from this MAC address.
IPv4 Addresses - Indicates ACL action will be on packets from this IPv4 source address.
IPv6 Address - Indicates ACL action will be on packets from this IPv6 source address.
To: Specify the destination of accessible packets. The possible values are:
Any - Indicates ACL action will be on packets to any destination.
MAC Address - Indicates ACL action will be on packets from this MAC address. The field of format is xx-xx-xx-xx-xx-xx.
IPv4 Addresses - Indicates ACL action will be on packets from this IPv4 source address.
IPv6 Address - Indicates ACL action will be on packets from this IPv6 source address.
Service Type: Specify the Type of Service to match. The possible values are:
Any - Indicates any service type of packets are examined.
Ether type - Select Ethernet type and IP, ARP or User Define address for filtering packets.
ICMP All - Indicates all ICMP packets are examined.
IGMP - IGMP packets can be filtered by IGMP message type.
TCP All - Indicates all TCP packets are examined.
TCP Source Port - Specify packets from the TCP source port.
TCP Destination Port - Matches the packet to the TCP Destination Port.
UDP All - Indicates all UDP packets are examined.
UDP Source Port - Specify packets from the UDP source port.
UDP Destination Port - Matches the packet to the UDP Destination Port.
Action: Specify the forwarding action for packets matching the ACL rule. Permit forwards packets if all conditions are met. Deny drops packets if all conditions are met.
66
5 Configuration
D-Link Web Smart Switch User Manual
Ports: Enter a range of ports to be configured.
Press Apply for the settings to take effect.
NOTE: Once the ACL rules conflict, rules with the smaller rule ID will take higher priority.
NOTE: Be careful on ACL configuration.
Inappropriate design may lead to management access failure.
ACL > ACL Profile List
The ACL Profile List provides information for configuring ACL Profiles manually. ACL profiles are attached to interfaces, and define how packets are forwarded if they match the ACL criteria.
Figure 5.85 – ACL > ACL Profile List
The contents of Access Profile List table include:
Profile ID: Indicates the profile Identification number. The possible configured profile IDs are 1~50, and profile ID 51 is reserved for Voice VLAN.
Type: The owner type of ACL profile; it can be normal ACL or Voice VLAN.
Profile Summary: Displays the profile summary.
Show Details: To display an ACL’s profile details. The ACL profile details are displayed below the ACL table.
Show Rules: To show the access rule in this profile.
Edit / New Rules: To edit or create an access rule in this profile. To add a new rule, please see Access
Rule List in the next section.
Delete: To delete an access profile.
To manually add a profile, click Add:
6 7
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.86 – Add Access Profile
The steps of adding an access profile are described below:
1) After selecting the Profile ID and Frame Type (MAC, IPv4 or IPv6), specify attributes like
Untagged/Tagged (for MAC), ICMP/IGMP/TCP/UDP (for IPv4), or ICMP/TCP/UDP (for IPv6). Click Select and a simplified frame diagram will be displayed.
Figure 5.87 – Add Access Profile
The Add ACL Profile Page contains the following fields:
Parameter
Profile ID
Description
Select an unique identifier number for this profile set. This value is from 2 to 50.
68
5 Configuration
D-Link Web Smart Switch User Manual
Frame Type
Select frame type based on MAC address, IPv4 address, IPv6 address or packet content. This will change the window according to the requirements for the type of profile.
Select MAC ACL to instruct the Switch to examine the layer 2 part of each packet header.
Select IPv4 ACL to instruct the Switch to examine the IPv4 address in each frame’s header.
Select IPv6 ACL to instruct the Switch to examine the IPv6 address in each frame’s header.
Select Packet Content to instruct the Switch to examine the packet content in each frame’s header.
MAC ACL
IPv4 ACL
IPv6 ACL
Defines the ACL profile Layer 2 protocols. The possible values are:
Tagged - Defines the profile Layer 2 to match 802.1Q fields in the
Layer 2 header.
Untagged - Defines the profile Layer 2 to check the Layer 2 header without the 802.1Q fields.
Defines the IPv4 ACL profile protocols. The possible fields are:
ICMP - Specifies ICMP as the Layer 4 protocol that the access profile checks.
IGMP - Specifies IGMP as the Layer 4 protocol that the access profile checks.
TCP - Specifies TCP as the Layer 4 protocol that the access profile checks.
UDP - Specifies UDP as the Layer 4 protocol that the access profile checks.
Defines the IPv6 ACL profile protocols. The possible fields are:
ICMP — Specifies ICMP as the Layer 3 IPv6 protocol that the access profile checks.
TCP — Specifies TCP as the Layer 3 IPv6 protocol that the access profile checks.
UDP — Specifies UDP as the Layer 3 IPv6 protocol that the access profile checks.
To define the MAC ACL profile: Select MAC ACL with Tagged and click Select button. The updates to show the follows:
6 9
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.88 – Add Access Profile (MAC ACL)
The Add ACL Profile MAC ACL contains the following fields:
Field
Source MAC Mask
Description
Enter a MAC address mask for the source MAC address, e.g. FF-FF-FF-
FF-FF-FF.
Destination MAC Mask
802.1p
VLAN ID
Ether Type
Enter a MAC address mask for the destination MAC address, e.g. FF-FF-
FF-FF-FF-FF.
Selecting this option instructs the Switch to examine the 802.1Q VLAN identifier of each packet header and use this as the full or partial criterion for forwarding.
Selecting this option instructs the Switch to examine the 802.1p priority value of each packet header and use this as the, or part of the criterion for forwarding.
Selecting this option instructs the Switch to examine the Ethernet type value in each frame’s header.
Click Add button then the ACL profile is added.
To define the IPv4 ACL ICMP profile: Select IPv4 ACL with ICMP and click Select button. The updates to show the follows:
70
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.89 – Add Access Profile (IPv4 ACL ICMP)
The Add ACL Profile IPv4 ACL ICMP address page contains the following fields:
Field
Source IP Mask
Description
Defines the range of source IP addresses, relevant to the ACL rules.
(0=ignore, 1=check).
For example, to set 176.212.XX.XX, use mask 255.255.0.0
Destination IP Mask
ICMP Type
Defines the range of destination IP addresses, relevant to the ACL rules.
(0=ignore, 1=check).
For example, to set 176.212.XX.XX, use mask 255.255.0.0
Sets the ICMP Type field as an essential field to match.
ICMP Code Sets the ICMP code field as an essential field to match.
Click Add button then the ACL profile is added.
To define the IPv4 ACL IGMP profile: Select IPv4 ACL with IGMP and click Select button. The updates to show the follows:
7 1
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.90 – Add Access Profile (IPv4 ACL IGMP)
Click Add button then the ACL profile is added.
To define the IPv4 ACL TCP profile: Select IPv4 ACL with TCP and click Select button. The updates to show the follows:
Figure 5.91 – Add Access Profile (IPv4 ACL TCP)
72
5 Configuration
D-Link Web Smart Switch User Manual
The Add ACL Profile IPv4 ACL TCP port page contains the following fields:
Field Description
Source Port Mask Defines the range of source Ports relevant to the ACL rules. (0=ignore,
1=check).
For example, to set 0 – 15, set mask of FFF0.
Destination Port Mask
TCP Flag
Defines the range of destination IP addresses, relevant to the ACL rules.
(0=ignore, 1=check).
For example, to set 0 – 15, set mask of FFF0.
Sets the TCP Flag Type field as an essential field to match.
Click Add button then the ACL profile is added.
To define the IPv4 ACL UDP profile: Select IPv4 ACL with UDP and click Select button. The updates to show the follows:
Figure 5.92 – Add Access Profile (IPv4 ACL UDP)
The Add ACL Profile IPv4 ACL UDP port page contains the following fields:
Field Description
Source Port Mask
Destination Port Mask
Defines the range of source Ports relevant to the ACL rules. (0=ignore,
1=check).
For example, to set 0 – 15, set mask of F.
Defines the range of destination IP addresses, relevant to the ACL rules.
(0=ignore, 1=check).
For example, to set 0 – 15, set mask of F.
Click Add button then the ACL profile is added.
NOTE: A combination of one or several filtering masks can be selected simultaneously. The page updates with the relevant field(s).
7 3
5 Configuration
D-Link Web Smart Switch User Manual
To define the IPv6 ACL ICMP profile: Select IPv6 ACL with ICMP and click Select button. The updates to show the follows:
Figure 5.93 – Add Access Profile (IPv6 ACL ICMP)
The Add ACL Profile IPv6 ACL ICMP address page contains the following fields:
Field
Source IP Prefix
Description
Defines the range of source IP addresses, relevant to the ACL rules.
(0=ignore, 1=check).
For example, to set 2002:0:0:0:0:0:b0d4:0, use mask 128
Destination IP Prefix Defines the range of destination IP addresses, relevant to the ACL rules.
(0=ignore, 1=check).
For example, to set 2002:0:0:0:0:0:bfd4:0, use mask 128
ICMP Type
ICMP Code
Sets the ICMP Type field as an essential field to match.
Sets the ICMP code field as an essential field to match.
Click Add button then the ACL profile is added.
To define the IPv6 ACL TCP profile: Select IPv6 ACL with TCP and click Select button. The updates to show the follows:
74
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.94 – Add Access Profile (IPv6 ACL TCP)
The Add ACL Profile IPv6 ACL TCP port page contains the following fields:
Field
Source Port Mask
Description
Destination Port Mask
Defines the range of source Ports relevant to the ACL rules. (0=ignore,
1=check).
For example, to set 0 – 15, set mask of FFF0.
Defines the range of destination IP addresses, relevant to the ACL rules.
(0=ignore, 1=check).
For example, to set 0 – 15, set mask of FFF0.
Click Add button then the ACL profile is added.
To define the IPv6 ACL UDP profile: Select IPv6 ACL with UDP and click Select button. The updates to show the follows:
7 5
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.95 – Add Access Profile (IPv6 ACL UDP)
The Add ACL Profile IPv6 ACL UDP port page contains the following fields:
Field
Source Port Mask
Description
Destination Port Mask
Defines the range of source Ports relevant to the ACL rules. (0=ignore,
1=check).
For example, to set 0 – 15, set mask of F.
Defines the range of destination IP addresses, relevant to the ACL rules.
(0=ignore, 1=check).
For example, to set 0 – 15, set mask of F.
Click Add button then the ACL profile is added.
NOTE: A combination of one or several filtering masks can be selected simultaneously. The page updates with the relevant field(s).
2) Selecting the field of interest will display the related columns in the lower part of the page. Enter the filtering mask and click Apply when done. A filtering mask is to specify the digit that you want to check. For example, if you want to check a network of 192.168.1.0/24, then you should enter the IP mask as
255.255.255.0.
Figure 5.96 – Access Rule List
NOTE: You cannot select Payload in a MAC ACL, or L2 Header in IP ACL.
76
5 Configuration
D-Link Web Smart Switch User Manual
3) After the Profile ID has been created, click Continue to go back to the main Access Profile List page, clicking the Edit / New Rules button to enter the Access Rule List page.
Figure 5.97 – Access Rule List
Profile ID: Indicates the corresponding access profile Identification number.
Access ID: Indicates the access rule Identification number.
Profile Type: Displays the profile type.
Summary: Displays the access rule summary.
Action: Displays the access rule action.
To add a new rule, click Add:
Figure 5.98 – Add Access Rule
Profile Information displays the information to which the rule is being added to, including Profile ID and
Ether Type.
In Rule Detail, you can specify the details of an access rule. Below are all the possible parameters that can be set.
Access ID: Specify the Access ID (1-65535).
Type: Display the type of rule. MAC, IPv4 or IPv6.
IPv6 Class: Specify the class of IPv6. The range is 0 to 255.
VLAN ID: Specify the VLAN ID.
Destination IPv6 Address: Specify the destination IPv6 address.
Source IPv6 Address: Specify the source IPv6 address.
IP Protocol: Specify the IP protocol of access rule.
Type: Specify the type. The possible value is from 0 to 255.
Code: Specify the code of access rule. The field range is from 0 to 255.
Ports: Specify the switch ports that you want to implement the access rule to.
Action: Specify the ACL forwarding action matching the rule criteria. Permit forwards packets if all other ACL criteria are met. Deny drops packets if all other ACL criteria is met.
7 7
5 Configuration
D-Link Web Smart Switch User Manual
Click Apply to make it effective.
NOTE: The switch begins the access rule with the smallest access ID, so be careful in assigning the
ID for the expected results.
To modify an existing rule, please click on the Access ID hyperlink.
Figure 5.99 – ACL > Access Profile List > Access Rule List
ACL > ACL Finder
This page is used to help find a previously configured ACL entry. To search for an entry, enter the profile ID from the drop-down menu, select a port that you wish to view, define the state and click Search. The table on the lower half of the screen will display the entries. To delete an entry click the corresponding Delete button.
Figure 5.100 – ACL > ACL Finder
PoE > PoE Global Settings (DGS-1210-10P/28P only)
This page will display the PoE status including System Budget Power, Support Total Power, Remainder
Power, and The ratio of system power supply.
Figure 5.101 – PoE > PoE Global Setting
System Power Threshold: Manually configure the system power budget 7.1 ~ 78.0 watts for DGS-1210-
10P and 7.1 ~ 185.0 watts for DGS-1210-28P.
Power Shut Off Sequence: Defines the method used to deny power to a port once the threshold is reached.
The possible fields are:
Deny next port: When the power budget is exceeded, the next port attempting to power up is denied, regardless of the port priority.
Deny low priority port: The port with the lower priority will be shut down to allow the higher priority port to power up.
Click Apply to make the configurations take effects.
78
5 Configuration
D-Link Web Smart Switch User Manual
System Power Status: Displays the system power status of device.
Total PoE Power Budget: Displays the total PoE power budget of this switch.
Power Used: Displays the current used power of the switch.
Power Left: Displays the spare power of the switch.
The percentage of system power supplied: Displays the percentage of system power supplied of the switch.
PoE > PoE Port Settings (DGS-1210-10P/28P only)
DGS-1210-10P/28P supports Power over Ethernet (PoE) as defined by the IEEE specification. It supplies power to PD device up to 15.4W for all ports or 30W for port 1~4, meeting IEEE802.3af standards and pre-
802.3at standards.
DGS-1210-10P/28P works with all D-Link 802.3af or 802.3at capable devices. The Switch also works in PoE mode with all non-802.3af capable D-Link AP, IP Cam and IP phone equipment via the PoE splitter DWL-
P50.
IEEE 802.3at defined that the PSE provides power according to the following classification:
Class Usage
0 Default
Output power limit by PSE
15.4W
3
4
1
2
Optional
Optional
Optional
4.0W
7.0W
15.4W
Reserved 30W
The PoE port table will display the PoE status including, Port Enable, Power Limit, Power (W), Voltage (V),
Current (mA), Classification, Port Status. You can select From Port / To Port to control the PoE functions of a port. DGS-1210-10P/28P will auto disable the ports if port current is over 375mA in 802.3af mode or
625mA in pre-802.3at mode.
Note: The PoE Status information of Power current, Power Voltage, and Current is the power usage information of the connected PD; please
"Refresh" to renew the information.
Figure 5.102 – PoE > PoE Port Setting
From Port/To Port: Specifies the PoE function of a port or ports.
State: Select “Enabled” or “Disabled” to configure PoE function for designated port(s). Default is Enabled.
7 9
5 Configuration
D-Link Web Smart Switch User Manual
Time Range: Select the PoE time profile configured from Time-Based PoE > Time Range Settings to enable the time-based PoE function on designated port(s). Default setting is N/A.
Priority: Configure the power supply priority as “Low”, “Normal”, or “High” on designated port(s). Default is
Normal.
Power Limit: This function allows you to manually set the port power current limitation to be given to the PD.
To protect the DGS-1210-10P/28P and the connected devices, the power limit function will disable the PoE function of the port when the power is overloaded. Select from "Class 1", "Class 2", "Class 3", “Class 4” and "Auto" for the power limit. "Auto" will negotiate and follow the classification from the PD power current based on the 802.3at standard.
User Define: Check the box and input the power budget (from 1 to 30W) to manually assign an upper limit of port power budget on designated port(s).
Click Apply to make the configurations take effects or click Refresh to redisplay the table.
Note: For the PoE Port Settings table, if the classification was shown as “Legacy PD”, it will be classified to non-AF PD or Legacy PD.
SNMP > Trap to SmartConsole Utility
By configuring the Trap Setting, it allows SmartConsole Utility to monitor specified events on this Web-Smart
Switch. By default, Trap Setting is disabled. When the Trap Setting is enabled, enter the Destination IP address of the managing station that will receive trap information when event happens.
Figure 5.103 – SNMP > Trap to SmartConsole Utility
You can select which event message(s) to be sent to the managing station.
Destination IP: Specifies the destination IP.
Illegal Login: Events of incorrect password logins, recording the IP of the originating PC.
Device Bootup: System boot-up information.
Port Link Up / Link Down: Copper port connection information.
RSTP Port State Change: Events of a RSTP port state changes.
Firmware Upgrade State: Information of firmware upgrade - success or failure.
PoE Power On / Off: Status of power per port (Only for DGS-1210-10P/28P)
PoE Power Error: The four trap events are: power over loading, short circuit, thermal shutdown and power deny (Only for DGS-1210-10P/28P).
NOTE: The total PoE power budget is 78 watts for
DGS-1210-10P and 185 watts for DGS-1210-28P.
The remaining 7watts is reserved for the last PoE device to be connected to the switch. The Power
Deny trap message is sent out when the switch hits the total power budget and when a new
Power Device (PD) requests to connect to the
80
5 Configuration
D-Link Web Smart Switch User Manual switch at the same time.
PoE Over Max Power Budget: When the system supplies power to PDs and hits the max PoE power budget of 78watts and 185watts, the system will send out this trap message. (Only for DGS-1210-10P/28P)
SNMP > SNMP > SNMP Global Settings
Simple Network Management Protocol (SNMP) is an OSI Layer 7 (Application Layer) protocol designed specifically for managing and monitoring network devices. SNMP enables network management stations to read and modify the settings of gateways, routers, switches, and other network devices. Use SNMP to configure system features for proper operation, monitor performance and detect potential problems in the
Switch or LAN.
Managed devices that support SNMP include software (referred to as an agent), which runs locally on the device. A defined set of variables (managed objects) is maintained by the SNMP agent and used to manage the device. These objects are defined in a Management Information Base (MIB), which provides a standard presentation of the information controlled by the on-board SNMP agent. SNMP defines both the format of the
MIB specifications and the protocol used to access this information over the network.
The default SNMP global state is disabled. Select Enable and click Apply to enable the SNMP function.
Figure 5.104 – SNMP > SNMP > SNMP Global Settings
Trap Settings: Specifies whether the device can send SNMP notifications.
SNMP Authentication Traps: Specifies the device to send authentication failure notifications.
Device Bootup: System boot-up information.
Illegal Login: Events of incorrect password logins, recording the IP of the originating PC.
Port Link Up / Link Down: Copper port connection information.
RSTP Port State Change: Events of a RSTP port state changes.
Firmware Upgrade State: Information of firmware upgrade - success or failure.
PoE Power On / Off: Status of power per port (Only for DGS-1210-10P/28P)
PoE Power Error: The four trap events are: power over loading, short circuit, thermal shutdown and power deny (Only for DGS-1210-10P/28P).
NOTE: The total PoE power budget is 78 watts for
DGS-1210-10P and 185 watts for DGS-1210-28P.
The remaining 7watts is reserved for the last PoE device to be connected to the switch. The Power
Deny trap message is sent out when the switch hits the total power budget and when a new
Power Device (PD) requests to connect to the switch at the same time.
PoE Over Max Power Budget: When the system supplies power to PDs and hits the max PoE power budget of 78 watts and 185 watts, the system will send out this trap message. (Only for DGS-
1210-10P/28P)
8 1
5 Configuration
D-Link Web Smart Switch User Manual
SNMP > SNMP > SNMP User
This page is used to maintain the SNMP user table for the use of SNMPv3. SNMPv3 allows or restricts users using the MIB OID, and also encrypts the SNMP messages sent out between users and Switch.
Figure 5.105 – SNMP > SNMP > SNMP User Table
User Name: Enter a SNMP user name of up to 32 characters.
Group Name: Specify the SNMP group of the SNMP user.
SNMP Version: Specify the SNMP version of the user. Only SNMPv3 encrypts the messages.
Encrypt: Specifies the Encrypt is enabled or disabled when the SNMP Version is V3.
Auth-Protocol/Password: Specify either HMAC-MD5-96 or HMAC-SHA to be the authentication protocol.
Enter a password for SNMPv3 encryption in the right column.
Priv-Protocol/Password: Specify either no authorization or DES 56-bit encryption and then enter a password for SNMPv3 encryption in the right column.
Click Add to create a new SNMP user account, and click Delete to remove any existing data.
SNMP > SNMP > SNMP Group Table
This page is used to maintain the SNMP Group Table associating to the users in SNMP User Table.
SNMPv3 can control MIB access policy, security policy for a user group directly.
Group Name: Specify the SNMP user group of up to 32 characters.
Read View Name: Specify a SNMP group name for users that are allowed SNMP read privileges to the
Switch's SNMP agent.
Write View Name: Specify a SNMP group name for users that are allowed SNMP write privileges to the
Switch's SNMP agent.
Security Model: Select the SNMP security model.
SNMPv1 - SNMPv1 does not support the security features.
SNMPv2 - SNMPv2 supports both centralized and distributed network management strategies. It includes improvements in the Structure of Management Information (SMI) and adds some security features.
SNMPv3 - SNMPv3 provides secure access to devices through a combination of authentication and encrypting packets over the network.
Security Level: This function is only available when you select SNMPv3 security level.
NoAuthNoPriv - No authorization and no encryption for packets sent between the Switch and SNMP manager.
AuthNoPriv - Authorization is required, but no encryption for packets sent between the Switch and
SNMP manager.
AuthPriv – Both authorization and encryption are required for packets sent between the Switch and
SNMP manger.
Notify View Name: Specify a SNMP group name for users that can receive SNMP trap messages generated by the Switch's SNMP agent.
82
5 Configuration
D-Link Web Smart Switch User Manual
Figure 5.106 – SNMP > SNMP > SNMP Group Table
SNMP > SNMP > SNMP View
This page allows you to maintain SNMP views to community strings that define the MIB objects which can be accessed by a remote SNMP manager.
Figure 5.107 – SNMP > SNMP > SNMP View
View Name: Name of the view, up to 32 characters.
Subtree OID: The Object Identifier (OID) Subtree for the view. The OID identifies an object tree (MIB tree) that will be included or excluded from access by an SNMP manager.
OID Mask: The mask of the Subtree OID. 1 means this object number is concerned, 0 means do not concerned. For example 1.3.6.1.2.1.1 with mask 1.1.1.1.1.1.0 means 1.3.6.1.2.1.X.
View Type: Specify the configured OID is Included or Excluded that a SNMP manager can access.
Click Add to create a new view, Delete to remove an existing view.
SNMP > SNMP > SNMP Community
This page is used to maintain the SNMP community string of the. SNMP managers using the same community string are permitted to gain access to the Switch's SNMP agent.
Community Name: Name of the community string
User Name (View Policy): Specify the read/write or read-only level permission for the MIB objects accessible to the SNMP community.
Figure 5.108 –SNMP > SNMP > SNMP Community
Click Add to create a new SNMP community, Delete to remove an existing community.
8 3
5 Configuration
SNMP > SNMP > SNMP Host
This SNMP Host page is to configure the SNMP trap recipients.
D-Link Web Smart Switch User Manual
Figure 5.109 – SNMP > SNMP > SNMP Host
Host IP Address: Select IPv4 or IPv6 and specify the IP address of SNMP management host.
SNMP Version: Specify the SNMP version to be used to the management host.
Community String/SNMPv3 User Name: Specify the community string or SNMPv3 user name for the management host.
Click Apply to create a new SNMP host, Delete to remove an existing host.
SNMP > SNMP > SNMP Engine ID
The Engine ID is a unique identifier used to identify the SNMPv3 engine on the Switch.
Input the Engine ID then click Apply to apply the changes and click Default resets to default value.
Figure 5.110 – SNMP > SNMP > SNMP Engine ID
SNMP > RMON > RMON Global Settings
Users can enable and disable remote monitoring (RMON) status for the SNMP function on the Switch. In addition, RMON Rising and Falling Alarm Traps can be enabled and disabled. Click Apply to make effects.
Figure 5.111 - SNMP > RMON > RMON Global Settings
SNMP > RMON > RMON Statistics
The RMON Statistics Configuration page displays the information of RMON Ethernet Statistics and allows the user to configure the settings.
Figure 5.112 - SNMP > RMON > RMON Ethernet Statistics Configuration
The RMON Ethernet Statistics Configuration contains the following fields:
84
5 Configuration
D-Link Web Smart Switch User Manual
Index (1 - 65535): Indicates the RMON Ethernet Statistics entry number.
Port: Specifies the port from which the RMON information was taken.
Owner: Displays the RMON station or user that requested the RMON information.
Click Add to make the configurations take effects and click Refresh to redisplay the table information.
SNMP > RMON > RMON History
The RMON History Control Configuration page contains information about samples of data taken from ports.
For example, the samples may include interface definitions or polling periods.
Figure 5.113 - SNMP > RMON > RMON History Control Settings
The History Control Configuration contains the following fields:
Index (1 - 65535): Indicates the history control entry number.
Port: Specifies the port from which the RMON information was taken.
Buckets Requested (1 ~ 50): Specifies the number of buckets that the device saves.
Interval (1 ~ 3600): Indicates in seconds the time period that samplings are taken from the ports. The field range is 1-3600. The default is 1800 seconds (equal to 30 minutes).
Owner: Displays the RMON station or user that requested the RMON information.
Click Apply to make the configurations take effects.
SNMP > RMON > RMON Alarm Settings
The RMON Alarm Settings page allows the user to configure the network alarms. Network alarms occur when a network problem, or event, is detected.
Figure 5.114 -. SNMP > RMON > RMON Alarm Settings
The configuration contains the following fields:
Index (1 - 65535): Indicates a specific alarm.
Variable: Specify the selected MIB variable value.
Rising Threshold (0 ~ 2^31-1): Displays the rising counter value that triggers the rising threshold alarm.
Rising Event Index (1 ~ 65535): Displays the event that triggers the specific alarm. The possible field values are user defined RMON events.
Owner: Displays the device or user that defined the alarm.
Interval (1 ~ 2^31-1): Defines the alarm interval time in seconds.
8 5
5 Configuration
D-Link Web Smart Switch User Manual
Sample type: Defines the sampling method for the selected variable and comparing the value against the thresholds. The possible field values are:
Delta value – Subtracts the last sampled value from the current value. The difference in the values is compared to the threshold.
Absolute value – Compares the values directly with the thresholds at the end of the sampling interval.
Falling Threshold (0 ~ 2^31-1): Displays the falling counter value that triggers the falling threshold alarm.
Falling Event Index (1 ~ 65535): Displays the event that triggers the specific alarm. The possible field values are user defined RMON events.
Click Add to make the configurations take effects.
SNMP > RMON > RMON Event
The RMON Event page contains fields for defining, modifying and viewing RMON events statistics.
Figure 5.115 - SNMP > RMON > RMON Event Settings
The RMON Events Page contains the following fields:
Index (1~ 65535): Displays the event.
Description: Specifies the user-defined event description.
Type: Specifies the event type. The possible values are:
None – Indicates that no event occurred.
Log – Indicates that the event is a log entry.
SNMP Trap – Indicates that the event is a trap.
Log and Trap – Indicates that the event is both a log entry and a trap.
Community: Specifies the community to which the event belongs.
Owner: Specifies the time that the event occurred.
Click Add to add a new RMON event.
Monitoring > Port Statistics
The Port Statistics screen displays the status of each port packet count.
Figure 5.116 – Monitoring > Port Statistics
Refresh: Renews the details collected and displayed.
86
5 Configuration
D-Link Web Smart Switch User Manual
Clear: To reset the details displayed.
TxOK: Number of packets transmitted successfully.
RxOK: Number of packets received successfully.
TxError: Number of transmitted packets resulting in error.
RxError: Number of received packets resulting in error.
To view the statistics of individual ports, click one of the linked port numbers for details.
Figure 5.117 – Monitoring > Port Statistics
Back: Go back to the Statistics main page.
Refresh: To renew the details collected and displayed.
Clear: To reset the details displayed.
Monitoring > Cable Diagnostics
The Cable Diagnostics is designed primarily for administrators and customer service representatives to examine the copper cable quality. It rapidly determines the type of cable errors occurred in the cable.
Select a port and then click the Test Now button to start the diagnosis.
Figure 5.118 – Monitoring > Cable Diagnostic
Test Result: The description of the cable diagnostic results.
•OK means the cable is good for the connection.
•Short in Cable means the wires of the RJ45 cable may be in contact somewhere.
•Open in Cable means the wires of RJ45 cable may be broken, or the other end of the cable is simply disconnected.
•Test Failed means some other errors occurred during cable diagnostics. Please select the same port and test again.
Cable Fault Distance (meters): Indicates the distance of the cable fault from the Switch port, if the cable is less than 2 meters, it will show “No Cable”.
Cable Length (meter): If the test result shows OK, then cable length will be indicated for the total length of the cable. The cable lengths are categorized into four types: <50 meters, 50~80 meters, 80~100 meters and
>100 meters.
8 7
5 Configuration
D-Link Web Smart Switch User Manual
NOTE: Cable length detection is effective on
Gigabit ports only.
NOTE: Please be sure that Power Saving feature is disabled before enabling Cable Diagnostics function.
Monitoring > System Log
The System Log page provides information about system logs, including information when the device was booted, how the ports are operating, when users logged in, when sessions timed out, as well as other system information.
Figure 5.119 – Monitoring > System Log
ID: Displays an incremented counter of the System Log entry. The Maximum entries are 500.
Time: Displays the time in days, hours, and minutes the log was entered.
Log Description: Displays a description event recorded.
Severity: Displays a severity level of the event recorded.
Click Refresh to renew the page, and click Clear to clean out all log entries.
88
6 Command Line Interface
D-Link Web Smart Switch User Manual
6
Command Line Interface
The D-Link Web Smart Switch allows a computer or terminal to perform some basic monitoring and configuration tasks by using the Command Line Interface (CLI) via TELNET protocol.
To connect a switch via TELNET:
1. Make sure the network connection between the switch and PC is active.
2. To connect, launch any terminal software like HyperTerminal in Microsoft Windows, or just use the command prompt by typing the command telnet followed by the switch IP address, eg. telnet 10.90.90.90.
3. The logon prompt will appear.
Logging on to the Command Line Interface:
Enter your User Name and Password to log in. The default user name and password is admin. Note that the user name and password are case-sensitive. Press Enter in both the Username and Password fields. The command prompt will appear as shown below (DGS-1210-52>):
DGS-1210-52 login: admin
Password:
DGS-1210-52>
Figure 6.1 – Command Prompt
The user session is automatically terminated if idle for the login timeout period. The default login timeout period is 5 minutes. To change the login timeout session, please refer to chapter 5.
CLI Commands:
The Basic Switch commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table.
Command
?
download
Upload config ipif system config ipif system logout ping ping6 reboot reset config show ipif show switch config account admin password
Parameter
{ firmware_fromTFTP | cfg_fromTFTP } {<ipaddr> | <ipv6addr>}
<path_filename>
{ firmware_fromTFTP | cfg_fromTFTP } {<ipaddr> | <ipv6addr>}
<path_filename>
{ ipaddress <ip-address> <subnet-mask> gateway <gw-address> | dhcp | bootp }
{ ipv6 ipv6address <ipv6networkaddr> | dhcpv6_client [enable | disable] }
<ip_addr>
<ipv6addr>
<passwd>
8 9
6 Command Line Interface
D-Link Web Smart Switch User Manual
Command Parameter
save debug info
Each command is listed in detail, as follows:
?
Purpose
Syntax
Description
Parameters
Restrictions
Example usage:
To display a list of commands.
?
The ? command displays a list of commands of the switch.
None.
None.
To display a list of commands of the switch:
DGS-1210-52> ?
USEREXEC commands :
config account admin password <passwd>
config ipif System { ipaddress <ip-address> <subnet-mask> gateway <gwaddress> | dhcp }
debug info
download { firmware_fromTFTP tftp://ip-address/filename | cfg_fromTFTP tftp://ip-address/filename }
logout
ping <ip_addr>
reboot
reset config
save
show ipif
show switch
upload { firmware_toTFTP tftp://ip-address/filename | cfg_toTFTP tftp://ipaddress/filename }
DGS-1210-52>
download
Purpose
Syntax
Description
Parameters
To download and install a firmware, boot, or switch configuration file from a TFTP server. download { firmware_fromTFTP | cfg_fromTFTP } {<ipaddr> |
<ipv6addr>} <path_filename>
The download command downloads a firmware, boot, or switch configuration file from a TFTP server.
firmware_fromTFTP
− Download and install new firmware on the
Switch from a TFTP server.
90
6 Command Line Interface
D-Link Web Smart Switch User Manual
cfg_fromTFTP
− Download a switch configuration file from a
TFTP server.
<ipaddr>
− The IPv4 address of the TFTP server.
<ipv6addr>
− The IPv6 address of the TFTP server.
<path_filename>
− The filename of the firmware or switch configuration file on the TFTP server. You need to specify the
DOS path if the file is not at the root directory of the TFTP server.
None. Restrictions
Example usage:
To download a firmware file:
DGS-1210-52>
download firmware_fromT F T P 1.1.1.23 1\dgs _1210-10032.ros
01–J an–2000 01: 19: 48 %C OP Y –I–F IL E C P Y : F iles C opy – s ource UR L tftp: //1.1.1.23 /1\ dgs _1210—10032.ros des tination UR L Unit all flas h: //image
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!01–J an–2000 01: 22: 49 %C OP Y –W–T R AP :
T he copy operation was completed s ucces s fully
!
3920460 bytes copied in 00: 03: 01 [hh: mm: s s ]
DGS-1210-52>
Note: Switch will reboot after restore and all current configurations will be lost.
upload
Purpose
Syntax
Description
To upload the firmware file or a Switch configuration file to a
TFTP server. upload { firmware_fromTFTP | cfg_fromTFTP } {<ipaddr> |
<ipv6addr>} <path_filename>
The upload command uploads the Switch’s current settings to a
TFTP server.
9 1
6 Command Line Interface
D-Link Web Smart Switch User Manual
Parameters firmware_toTFTP
− Upload the firmware on the Switch from a
TFTP server.
cfg_toTFTP
− Specifies that the Switch’s current settings will be uploaded to the TFTP server.
<ipaddr>
− The IPv4 address of the TFTP server.
<ipv6addr>
− The IPv6 address of the TFTP server.
<path_filename>
− The filename of the firmware or switch configuration file on the TFTP server. You need to specify the
DOS path if the file is not at the root directory of the TFTP server.
None. Restrictions
Example usage:
To upload a firmware file:
DGS-1210-52> upload firmware_toT FT P 1.1.1.23 1\running—config
01–J an–2000 01: 26: 11 %C OP Y –I–F IL E C P Y : F iles C opy – s ource UR L running–config des tination UR L tftp: //1.1.1.23/1\running–config
…..01–J an–2000 01: 26: 16 %C OP Y –W–T R AP : T he copy operation was completed s ucces s fully
!
158 bytes copied in 00: 00: 05 [hh: mm: s s ]
DGS-1210-52>
config ipif system
Purpose
Syntax
Description
Parameters
To configure the System IP interface. config ipif system { ipaddress <ip-address> <subnet-mask> gateway <gw-address> | dhcp | bootp }
The config ipif s ys tem command configures the System IP interface on the Switch.
ipaddress <ip-address> <subnet-mask>
− The IP address and subnet mask to be created. Users need to specify the address and mask information using the traditional format (for example,10.1.2.3/255.0.0.0)
gateway <gw-address>
− The IP address of the router or gateway. dhcp
− Allows the selection of the DHCP protocol for the assignment of an IP address to the Switch’s System IP interface. bootp
− Allows the selection of the BOOTP to the switch.
None. Restrictions
Example usage:
To configure the IP interface System:
DGS-1210-52> config ipif S ys tem ipaddres s 10.48.74.122/8
S ucces s .
92
6 Command Line Interface
D-Link Web Smart Switch User Manual
DGS-1210-52>
config ipif system
Purpose
Syntax
Description
Parameters
To configure the System IPv6 interface. config ipif system { ipv6 ipv6address <ipv6networkaddr> | dhcpv6_client [enable | disable] }
The config ipif s ys tem command configures the System IPv6 interface on the Switch. ipv6 ipv6address <ipv6networkaddr>
− Use this parameter to statically assign an IPv6address to this interface. This address should define a host address and a network prefix length.
Multiple IPv6 addresses can be configured for a single IP interface. Ex: 3ffe:501:ffff:100::1/64. The /64 represents the prefix length of the IPv6 addresses. dhcpv6_client [enable | disable]
− Specify the DHCPv6 client to be disabled or enabled.
None. Restrictions
Example usage:
To configure the IPv6 interface System:
DGS-1210-52> config ipif S ys tem ipv6 ipv6addres s 3ffe:501:ffff:100::1/64
S ucces s .
DGS-1210-52>
logout
Purpose
Syntax
Description
Parameters
Restrictions
Example usage:
To log out a user from the Switch’s console. logout
The logout command terminates the current user’s session on the Switch’s console.
None.
None.
To terminate the current user’s console session:
DGS-1210-52> logout
NOTE: Save your configuration changes before logging out.
ping
Purpose
Syntax
To test the connectivity between network devices.
<ipaddr>
9 3
6 Command Line Interface
D-Link Web Smart Switch User Manual
Description The ping command checks if another IP address is reachable on the network. You can ping the IP address connected to through the managed VLAN (VLAN 1 by default), as long as there is a physical path between the switch and the target IP equipment. By default, Switch sends five pings to the target IP.
<ipaddr> - The IP address of the host.
None.
Parameters
Restrictions
Example usage:
To ping the IP address 10.90.90.91:
DGS-1210-52> ping 10.90.90.91
Reply Received From :10.90.90.91, TimeTaken : 20 msecs
Reply Received From :10.90.90.91, TimeTaken : 20 msecs
Reply Received From :10.90.90.91, TimeTaken : 20 msecs
--- 10.90.90.91 Ping Statistics ---
3 Packets Transmitted, 3 Packets Received, 0% Packets Loss
DGS-1210-52>
ping6
Purpose
Syntax
Description
To test the connectivity between network devices. ping6 <ipv6addr>
The pingv6 command checks if another IP address is reachable on the network. You can ping the IP address connected to through the managed VLAN (VLAN 1 by default), as long as there is a physical path between the switch and the target IP equipment. By default, Switch sends five pings to the target IP.
<ipv6addr> - The IPv6 address of the host.
None.
Parameters
Restrictions
Example usage:
To ping the IP address 3000::1:
DGS-1210-52> ping6 3000 ::1
Reply Received From : 3000 ::1, TimeTaken : 20 msecs
Reply Received From : 3000 ::1, TimeTaken : 20 msecs
Reply Received From : 3000 ::1, TimeTaken : 20 msecs
--- 3000 ::1 Ping Statistics ---
3 Packets Transmitted, 3 Packets Received, 0% Packets Loss
DGS-1210-52>
94
6 Command Line Interface
D-Link Web Smart Switch User Manual
reboot
Purpose
Syntax
Description
To reboot the Switch. If the Switch is a member of a stack, it may be rebooted individually, without affecting the other members of the stack. reboot
The reboot command reboots the system. All network connections are terminated and the boot code executes.
None.
None.
Parameters
Restrictions
Example usage:
To restart the Switch:
DGS-1210-52> reboot
% Device will reboot, please wait a few minutes to re-login.
DGS-1210-52>
reset config
Purpose
Syntax
Description
Parameters
Restrictions
Example usage:
To reset the Switch to the factory default settings. res et config
All configurations will be reset to the default settings.
None.
None.
To restore all of the Switch’s parameters to their default values:
DGS-1210-52> res et config
% Device will reboot after reset configuration successfully.
DGS-1210-52>
show ipif
Purpose
Syntax
Description
Parameters
Restrictions
Example usage:
To display the configuration of an IP interface on the Switch. s how ipif
The s how ipif command displays the current IP address of the switch.
None.
None.
To display IP interface settings:
DGS-1210-52> s how ipif
9 5
6 Command Line Interface
D-Link Web Smart Switch User Manual
IP Setting Mode : Static
IP Address : 10.90.90.90
Subnet Mask : 255.0.0.0
Default Gateway : 0.0.0.0
DHCPv6 Client State : Disabled
IPv6 Global Unicast Address: 3ffe:501:ffff:100:100::1/64
DGS-1210-52>
show switch
Purpose
Syntax
Description
Parameters
Restrictions
Example usage:
To display information about the Switch. s how s witch
The s how s witch command displays the status of the switch.
None.
None.
To display the switch information:
DGS-1210-52> show switch
System Name :
System Contact :
System Location :
System up time : 0 days, 6 hrs, 32 min, 17 secs
System Time : 02/01/2012 06:32:19
System hardware version : B1
System firmware version : 3.10.006
System boot version : 1.00.005
System Protocol version : 2.001.004
System serial number : 1MB1733K0000A
MAC Address : 00-01-02-03-04-05
DGS-1210-52>
config account admin password
Purpose
Syntax
Description
Parameters
Restrictions
To display the configuration of an IP interface on the Switch. config account admin pas s word <pas s wd>
The config account admin pas s word command sets the administrator password.
<passwd>
− The new password of the administrator.
None.
96
6 Command Line Interface
D-Link Web Smart Switch User Manual
Example usage:
To configure the account admin password:
DGS-1210-52> config account admin pas s word 1234
DGS-1210-52>
save
Purpose
Syntax
Description
To save changes in the Switch’s configuration to non-volatile
RAM. s ave
The s ave command saves the configuration changes to the memory.
None.
None.
Parameters
Restrictions
Example usage:
To save the Switch’s current configuration to non-volatile RAM:
DGS-1210-52> save
Building configuration ...
[OK]
DGS-1210-52>
debug info
Purpose
Syntax
Description
To display the ARP table and MAC FDB information of the
Switch. debug info
The debut info command displays the ARP table and MAC FDB of the Switch.
None.
None.
Parameters
Restrictions
Example usage:
To display the ARP table and MAC FDB information of the Switch:
DGS-1210-52> debug info
% segmentation fault log file:
File doesn’t exist !!!
% ARP table :
Address Hardware Address Type Interface Mapping
------- ------ ----------- ---------------- ------ ------------- -------------
10.90.90.90 00:18:8b:bf:75:30 ARPA vlan1 Static
9 7
6 Command Line Interface
D-Link Web Smart Switch User Manual
10.90.90.98 00:19:5b:14:3d:c4 ARPA vlan1 Dynamic
10.255.255.255 ff:ff:ff:ff:ff:ff ARPA vlan1 Static
% MAC table :
Vlan Mac Address Type Ports
------ -------------------- -------- -------
1 00:00:00:00:00:26 Learnt Gi0/7
Total Mac Addresses displayed: 1
DGS-1210-52>
98
Appendix A - Ethernet Technology
D-Link Web Smart Switch User Manual
Appendix A - Ethernet Technology
This chapter will describe the features of the D-Link Web Smart Switch and provide some background information about Ethernet/Fast Ethernet/Gigabit Ethernet switching technology.
Gigabit Ethernet Technology
Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure, format, and support for CSMA/CD protocol, full duplex, and management objects, but with a tenfold increase in theoretical throughput of over 100-Mbps Fast Ethernet and a hundredfold increase over 10-Mbps Ethernet.
Since it is compatible with all 10-Mbps and 100-Mbps Ethernet environments, Gigabit Ethernet provides a straightforward upgrade without wasting existing investments in hardware, software, or trained personnel.
The increased speed and extra bandwidth offered by Gigabit Ethernet is essential in solving network bottlenecks, which frequently develops as more advanced computer users and newer applications continue to demand greater network resources. Upgrading key components, such as backbone connections and servers to Gigabit Ethernet technology, can greatly improve network response times as well as significantly speed up the traffic between subnets.
Gigabit Ethernet enables fast optical fiber connections to support video conferencing, complex imaging, and similar data-intensive applications. Likewise, since data transfers occur 10 times faster than Fast Ethernet, servers outfitted with Gigabit Ethernet NIC’s are able to perform 10 times the number of operations in the same amount of time.
In addition, the phenomenal bandwidth delivered by Gigabit Ethernet is the most cost-effective method to take advantage of today and tomorrow’s rapidly improving switching and routing internetworking technologies. With expected advances in the coming years in silicon technology and digital signal processing, which will enable Gigabit Ethernet to eventually operate over unshielded twisted-pair (UTP) cabling, a flexible foundation for the next generation of network technology products will be created. This will outfit your network with a powerful 1000-Mbps-capable backbone/server connection.
Fast Ethernet Technology
The growing importance of LANs, and the increasing complexity of desktop computing applications are fueling the need for high performance networks. A number of high-speed LAN technologies have been proposed to provide greater bandwidth and improve client/server response times. Among them, 100BASE-T
(Fast Ethernet) provides a non-disruptive, smooth evolution from the current 10BASE-T technology. The non-disruptive and smooth evolution nature, and the dominating potential market base, virtually guarantees cost-effective and high performance Fast Ethernet solutions.
100Mbps Fast Ethernet is a standard specified by the IEEE 802.3 LAN committee. It is an extension of the
10Mbps Ethernet standard with the ability to transmit and receive data at 100Mbps, while maintaining the
CSMA/CD Ethernet protocol. Since the 100Mbps Fast Ethernet is compatible with all other 10Mbps Ethernet environments, it provides a straightforward upgrade and utilizes existing investments in hardware, software, and personnel training.
Switching Technology
Another approach to push beyond the limits of Ethernet technology is the development of switching technology. A switch bridges Ethernet packets at the MAC address level of the Ethernet protocol transmitting among connected Ethernet or Fast Ethernet LAN segments.
Switching is a cost-effective way of increasing the total network capacity available to users on a local area network. A switch increases capacity and decreases network loading by dividing a local area network into different segments, which won’t compete with each other for network transmission capacity.
The switch acts as a high-speed selective bridge between the individual segments. The switch, without interfering with any other segments, automatically forwards traffic that needs to go from one segment to another. By doing this the total network capacity is multiplied, while still maintaining the same network cabling and adapter cards.
9 9
Appendix B - Technical Specifications
D-Link Web Smart Switch User Manual
Appendix B - Technical Specifications
Hardware Specifications
Key Components / Performance
Switching Capacity:
- DGS-1210-10P: 20Gbps
- DGS-1210-20: 40Gbps
- DGS-1210-28: 56Gbps
- DGS-1210-28P: 56Gbps
- DGS-1210-52: 104Gbps
Max. Forwarding Rate
- DGS-1210-10P: 14.88Mpps
- DGS-1210-20: 29.8Mpps
- DGS-1210-28: 41.7Mpps
- DGS-1210-28P: 41.7Mpps
- DGS-1210-52: 77.4Mpps
Forwarding Mode: Store and Forward
Packet Buffer memory:
- DGS-1210-10P: 1MBytes
- DGS-1210-20: 1MBytes
- DGS-1210-28: 1MBytes
- DGS-1210-28P: 1MBytes
- DGS-1210-52: 1MBytes
DDRII for CPU: 128M Bytes
Flash Memory: 16M Bytes
Port Functions
10/100/1000Base-T ports compliant with the following standards:
- IEEE 802.3
- IEEE 802.3u
- IEEE 802.3ab
- IEEE 802.3az Energy Efficient Ethernet
- IEEE 802.3af (DGS-1210-10P/28P only)
- IEEE 802.3at (DGS-1210-10P/28P only)
- Supports Half/Full-Duplex operations
- IEEE 802.3x Flow Control support for Full-
Duplex mode
- Auto MDI/MDIX
- IEEE802.3af Power over Ethernet on Port
1 ~ Port 8 GE ports (DGS-1210-10P only)
- IEEE802.3af Power over Ethernet on Port
1~ Port 24 GE ports (DGS-1210-28P)
- IEEE802.3at Power over Ethernet on Port
1~Port 8 GE ports (DGS-1210-10P)
- IEEE802.3at Power over Ethernet on Port
1~ Port 4 GE ports (DGS-1210-28P only)
SFP ports compliant with the following standards:
- IEEE 802.3z
- Supports Full-Duplex operations
SFP transceivers supported
- DGS-712 (1000Base-T)
- DEM-310GT (1000BASE-LX, 10km)
- DEM-311GT (1000BASE-SX, 550m)
- DEM-314GT (1000BASE-LH, 50km)
- DEM-315GT (1000BASE-ZX, 80km)
- DEM-312GT2 (1000BASE-SX, 2km)
WDM Transceivers Supported:
- DEM-330T (1000Base-BX,TX-1550/RX-
1310nm, 10km)
- DEM-330R (1000Base-BX,TX-1310/RX-
1550nm, 10km)
- DEM-331T (1000Base-BX,TX-1550/RX-
1310nm, 40km)
- DEM-331R (1000Base-BX,TX-1310/RX-
1550nm, 40km)
Physical & Environment
AC input, 100~240 VAC, 50/60Hz, internal universal power supply
Acoustic Value:
- DGS-1210-10P/20/28: 0dB (Fan-less)
- DGS-1210-28P: 52.2dB (3 Smart Fans)
- DGS-1210-52: 47.1dB (2 Smart Fans)
Operation Temperature:
- DGS-1210/20/28/28P/52: 5~50°C
- DGS-1210-10P: 5~40°C
Storage Temperature -20~70°C
Operation Humidity: 0%~95% RH
Storage Humidity: 0%~95% RH
Emission (EMI) Certifications
FCC class A
CE Class A
VCCI Class A
IC Class A
Safety Certifications cUL, LVD, CE
Features
L2 Features
Supports up to 16K MAC address
Supports 256 static MAC
Jumbo frame: Supports up to 10,000 bytes
IGMP snooping v1/v2:
- Supports 256 multicast groups
- Supports at least 64 static multicast groups
802.1D Spanning Tree
802.1w Rapid Spanning Tree
100
Appendix B - Technical Specifications
D-Link Web Smart Switch User Manual
Loopback Detection
802.3ad Link Aggregation:
- DGS-1210-10P: Supports max 5 groups per device and 8 ports per group
- DGS-1210-20: Supports max 10 groups per device and 8 ports per group
- DGS-1210-28/28P: Supports max 14 groups per device and 8 ports per group
- DGS-1210-52: Supports max 26 groups per device and 8 ports per group
Port mirroring
SNTP
LLDP/LLDP-MED
IPv6 neighbor Discovery (ND)
L2 Multicast Filtering
VLAN
802.1Q VLAN standard (VLAN Tagging)
Up to 256 static VLAN groups
Asymmetric VLAN
Management VLAN
Auto-Voice VLAN
Auto Surveillance VLAN
QoS (Quality of Service)
Priority queue mapping by :
- 802.1p
- DSCP
- ToS
- TCP/UDP port number
- IPv6 traffic class
Up to 4 queues per port
Supports Strict / WRR mode in queue handling
Bandwidth Control
AAA
802.1X port-based access control
Support RADIUS server
ACL
Max 50 ingress ACL profiles
Ingress ACL rules:
- DGS-1210-20/28/28P: 200 rules (each rule can be associated to a single port or multiple ports)
- DGS-1210-52: 450 rules
Support different ACL policy packet contents:
- MAC address
- Ethernet Type
- IPv4 address
- IPv6 address
- ICMP
- IGMP
- TCP/UDP port number
Security
Trusted Host
Port Security:Support 64 MAC addresses per port
Traffic Segmentation
D-Link Safeguard Engine
Broadcast Storm Control
ARP Spoofing Prevention: Supports max
64 entries
DHCP Server Screening: Able to configure 5 IP addresses for DHCP server.
SSL: Support v1/v2/v3
Smart Binding
- Support manual configuration and scanning for binding.
- Supports ARP packet inspection as default,
ARP and IP packet inspection as an option.
- Supports DHCP Snooping
OAM
Cable Diagnostics
Reset button (reset to factory default)
Management
Web-based GUI or SmartConsole Utility
D-Link proprietary CLI
SNMP support
DHCP client
Trap setting for destination IP, system events, fiber port events, twisted-pair port events
Password access control
Web-based configuration backup / restoration
Web-based firmware backup/restore
Firmware upgrade using SmartConsole
Utility & Web-based management
Reset, Reboot
D-Link Green Technology
Power Saving: Enabled by default to save power:
- By Link Status: Drastically save power when the switch port link is down. For example, no PC connection or the connected PC is powered off.
- By Cable Length: Detects the length of connected RJ-45 cables and adjusts power usage accordingly without affecting performance. Once the RJ-45 connection is less than 20 meters, the switch will reduce the power instead of full power, which is only needed for 100 meters cables.
- By LED Shut-Off: LEDs can be turned on/off by port or system through schedule.
- By Port Shut-Off: Each port on the system can be turned on/off by schedule.
1 0 1
Appendix B - Technical Specifications
- By Port Standby: Each port on the system enters sleep state by schedule.
- By System Hibernation: System enters hibernation by schedule. In this mode, switches save most power since main chipsets (both MAC and PHY) are disabled for all ports, and energy required to power the CPU is minimal.
D-Link Web Smart Switch User Manual
102
Appendix C – Rack mount Instructions
D-Link Web Smart Switch User Manual
Appendix C – Rack mount Instructions
Safety Instructions - Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions:
A) Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient. Therefore, consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised.
C) Mechanical Loading - Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.
D) Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring.
Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
E) Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g. use of power strips).
103
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Layer 2 management and security with Layer 3 capabilities
- Compact Command-Line Interface (CLI) and web-based User-Interface
- Static Routing and MSTP
- PoE options up to 370W power budget
- Dual image & config
Related manuals
advertisement