C.T.M. HS-360 User`s manual

C.T.M. Folding Power Chair
HS-6200 User's Manual
HS-6200
User's Manual
Table of Contents
Introduction.........................................................................1
Electromagnetic Interference and Warnings..........................3
Safety Instructions...............................................................5
Initial Overview....................................................................6
Unpacking and Assembly......................................................8
Special Features................................................................11
Safe Driving Techniques.....................................................14
Batteries and Charging.......................................................16
Tire....................................................................................18
Maintenance,and Cleaning..................................................19
Troubleshooting..................................................................20
Specification......................................................................22
HS-6200
User's Manual
INTRODUCTION
C.T.M. is a professional and experienced manufacturer, that specializes in production of
Mobility Scooters and Power Chairs that are developed by a team of specialists with
outstanding design skills and competence.
The HS-6200 is an excellent chair that includes ergonomic features. It combines safety
and comfort and gives users extraordinary experience and convenience in operation.
With its thoughtful and people-friendly controller system, the user can easily achieve
360 degree turns with their finger tips.
This product is powered by the sealed, no water added, high performance and, most of
all, connectorless lead-acid battery, which ensures environmental safety and brings
convenience in disassembly and re-assembly.
Preface:
This User's Manual contains important information and know-how on operating and
maintaining the C.T.M. product. Please read it carefully before practicing with your new
chair, so that you comprehend the technical advantages of HS-6200
All assembly and maintenance should be performed after you fully understand the content
of this manual to avoid any hazard or damage to the Power Chair or human body.
Overhaul and adjustments must be undertaken by skillful maintenance staff following the
instructions provided in this booklet.
Any improper usage might lead to danger to the user or the chair. C.T.M. is/will not be
responsible for any after-effect resulting from failure to comply with this manual.
After unpacking, please inspect carefully for any defect or missing part..
Limitation In Transporting And Travelling:
1. When transporting HS-6200, please ensure the product is not scratched or damaged.
2. If a long trip is planned, please fully charge the batteries before use to prevent low
voltage during the trip.
All the contents in this manual including pictures, photo illustrations and text are all patented
and registered. (If any details in the manual are going to be changed or added, C.T.M.
will not notify previous owners of the modification.)
1
HS-6200
User's Manual
We wish you an enjoyable riding experience.
If you have any questions, you can contact:
C.T.M.HOMECARE PRODUCT, INC.
6191 Schaefer Ave Suite B Chino CA 91710
Toll Free : 1-866-466-8168 Tel : 909-590-1388 Fax : 909-590-3365
E-Mail : ctm@ctmhomecare.com http : //www.ctmhomecare.com
or your local dealer:
2
HS-6200
User's Manual
ELECTROMAGNETIC INTERFERENCE
AND WARNINGS
CAUTION: It is very important that you read this information regarding the possible
effects of Electromagnetic Interference on your power chair.
Powered wheelchairs and motorized scooters may be susceptible to electromagnetic
interference (EMI), which is interfering electromagnetic energy (EM) emitted from sources
such as radio stations, TV stations, amateur radio (HAM) transmitters, two-way radios,
and cellular phones. The interference (from radio wave sources) can cause the power
chair to release its brakes, move by itself, or move in unintended directions. It can also
permanently damage the power chair control system. The intensity of the interfering
EM energy can be measured in volts per meter (V/m). Each power chair can resist EMI
up to a certain intensity. This is called its "immunity level." The higher the immunity level,
the greater the protection will be. At this time, current technology is capable of achieving
at least a 20 V/m immunity level, which would provide useful protection from the more
common sources of radiated EMI. The immunity level of this product is 20 V/m.
There are a number of sources of relatively intense electromagnetic fields in the everyday
environment. Some of these sources are obvious and easy to avoid. Others are not
apparent and exposure is unavoidable. However, we believe that by following the warnings
listed below, your risk to EMI will be minimized.
Electromagnetic Interference and Warnings:
The sources of radiated EMI can be broadly classified into three types:
1.Hand-held portable transceivers (transmitters-receivers) with the antenna mounted
directly on the transmitting unit. Examples include: citizens band (CB) radios,
"walkie talkie," security, fire, and police transceivers, cellular telephones, and other
personal communication devices.
Some cellular telephones and similar devices transmit signals while
they are ON, even when not being used.
2.Medium-range mobile transceivers, such as those used in police cars, fire trucks,
ambulances, and taxis. These usually have the antenna mounted on the outside of
the vehicle.
3
HS-6200
User's Manual
3.Long-range transmitters and transceivers such as commercial broadcast transmitters
(radio and TV broadcast antenna towers) and amateur (HAM) radios.
Other types of hand-held devices, such as cordless phones, laptop
computers, AM/FM radios, TV sets, CD players, and cassette players,
and small appliances, such as electric shavers and hair dryers, so far
as we know, are not likely to cause EMI problems to your power chair.
Power Chair Electromagnetic Interference:
Because EM energy rapidly becomes more intense as one moves closer to the transmitting
antenna (source), the EM fields from hand-held radio wave sources (transceivers) are of
special concern. It is possible to unintentionally bring high levels of EM energy very close
to the power chair control system while using these devices. This can affect power chair
movement and braking. Therefore, the warnings listed below are recommended to prevent
possible interference with the control system of the power chair.
Electromagnetic Interference and Warnings:
Warnings
Electromagnetic interference (EMI) from sources such as radio and TV stations, amateur
radio (HAM) transmitters, two-way radios, and cellular phones can affect the power chair.
Following the warnings listed below should reduce the chance of unintended brake release
or power chair movement, which could result in serious injury.
1.Do not operate hand-held transceivers (transmitters-receivers), such as citizens band
(CB) radios, or turn ON personal communication devices, such as cellular phones,
while the power chair is turned ON;
2.Be aware of nearby transmitters, such as radio or TV stations, and try to avoid coming
close to them;
3.If unintended movement or brake release occurs, turn the power chair OFF as soon
as it is safe;
4.Be aware that adding accessories or components, or modifying the power chair, may
make it more susceptible to EMI; and
5.Report all incidents of unintended movement or brake release to the distributor listed
on the inside front cover of this manual. Note whether there is a source of EMI nearby.
Important Information
1.20 volts per meter V/m is a generally achievable and useful immunity level against EMI
(as of May 1994). The higher the level, the greater the protection.
2.The immunity level of this product is 20 V/m.
4
HS-6200
User's Manual
SAFETY INSTRUCTIONS
Safety is the main consideration when practicing with your chair. It is required that you
read and comprehend all the operating and safety instructions discussed in this manual.
And ensure your chair is correctly fitted and adjusted by your dealer or the prescribing
healthcare professional.
Make sure to engage the wheel locks before entering or leaving the chair. The wheel locks
are designed to prevent movement of the chair. It is preferable to ensure the front castors
are in the forward position before transferring in to or out of the chair. With the castors
in the forward position the wheel base of the chair is increased and therefore, offers more
stability.
DO NOT move forward in the seat while leaning forward out of the chair. If an object is
to be picked up from the floor, drive past it, then reverse so the front castors are in the
forward position. This gives the chair its greatest stability.
To maintain lateral stability do not reach further than the length of your arm. DO NOT
lean out of the chair as this could cause instability.
When transferring, DO NOT stand on the leg rests. Depending on the style of leg rests
either swing them away or fold them up before transferring.
When approaching a ramp, be sure of your own ability and your limitations in terms of
strength and endurance.
Before attempting a ramp the following basic safety rules should be considered:
1.
2.
3.
4.
Surface of the ramp: Is it too slippery?
Degree of incline: Is it too steep to attempt alone?
Length of ramp: Is it too long for your endurance?
Obstacles: Are there any obstacles on the ramp that would necessitate assistance?
Be very careful when going up or down steep inclines
If it becomes necessary to stop when going up an incline, special care must be taken to
avoid abrupt or sudden forward movement. During continuous forward movements, the
chair is capable of falling backwards.
Always keep the chair under control when going down a ramp or incline. Speed should
be controlled at all times.
The user in the power chair and a curb is encountered, caution should be taken to
prevent the user being thrown forward:
Do not try to climb a curb by driving up it. Have a helper move the chair for you following
the instructions below.
1. With both motors disengaged, go down the curb, rear wheels first; making sure that
the user is square to the curb so that the rear wheels go down together.
2. To go up a curb forward, verify both front wheels are up together. This must be
accomplished with the motors disengaged.
Also try to avoid going up multiple steps and using escalators. Use the elevator instead.
Please be aware that any adjustments on the power chair may affect the
handling and performance.
5
HS-6200
User's Manual
INITIAL OVERVIEW
Super Responsive
Digital Joystick Controller
Padded Breathable
Ballistic Nylon Back Rest
Flip up and
Height Adjustable
Armrests
Connectorless
Battery Boxes
Fiber Glass Reinforced
Nylon Leg Rests
2 High Torque Motors
Mated to Precision
Sealed for Life
Gear reducers
Low Profile Cast
Aluminum Wheels with
Multi-Terrain Tires
Figure 1 - HS-6200 Front View
6
HS-6200
User's Manual
Handlebar
Support Brace
Charger
Carry-on Bag
Height Adjustable
Armrests Knob
Battery Box
Back & Forth Adjstable
Armrests Plug
Free Wheel Lever
Free Wheel Lever
Anti-Tip Wheels
Figure 2 - HS-6200 Back View
Charging Socket
Battery Level lndicator
speed Indicator
Horn
On/Off
Switch
Speed Control Button
Figure 3 - Joystick Top View
Figure 4 - Joystick Front View
7
HS-6200
User's Manual
UNPACKING AND ASSEMBLY
Pull two Pull Handles upward from the Holder (A) and (B), then turn outward to take out
the battery.(See Fig. 5)
Remove the Battery (C) by sliding along the slider.(See Fig. 6)
B
A
C
Figure 5
Figure 6
Remove the (D) Leg Band (Accessory).by tear off the Vel-Cro to release the Leg Band
(See Fig. 7)
Press the Lever (E) on the Footrest Frame downwards, then take out the Footrest Frame
by turning it outward.(See Fig. 8)
E
D
Figure 7
Figure 8
Pressing the Delta Tube Pin on the Delta Tube's Delta Tube Lock down to the bottom, then
push & pull the Delta Tube to the right side to release the Delta Tube Lock, next step pull
Delta Tube downwards to fold up.(See Fig. 9 ) (F) and (F1).
Unscrew bolt, (G), release the frame under the seat and fold up.(See Fig. 10)
F
F1
G
Figure 9
Figure 10
8
HS-6200
User's Manual
Slowly grasp the centre of the seat upholstery, one hand at the front and the other at the
rear, pull the seat upholstery up vertically.(See Fig. 11)
Push down the pulled up seat upholstery evenly.(See Fig. 12)
Figure 11
Figure 12
Hold the two armrests with your hands, to contract the armrests inwards.(See Fig. 13)
Assemble procedure refer to disassemble procedure.(See Fig. 14)
Figure 13
Figure 14
9
HS-6200
User's Manual
※When put the battery box (H) back to original position, place the battery box at the slide
terminal, (Do not set too far back otherwise the battery box won't be fit into the slide
tube accurately.)(See Fig. 15)
※Battery boxes are separate into front and rear sections, please disassemble and
assemble accordingly.(See Fig. 16)
※Final step: Using the Pull Handles (I) to secure battery box's position.(See Fig. 17)
H
I
Figure 15
Figure 16
Figure 17
10
HS-6200
User's Manual
SPECIAL FEATURES
Freewheel levers
K
For your convenience, C.T.M. HS-6200 is
equipped with two free wheel levers. These
levers allow you to disengage the drive motors
and maneuver the chair manually.
J
1.In travelling, set the two metallic levers
(J.K) to the Drive position.
2. When the chair stops or malfunctions
you can push the levers (J.K) to the
Neutral position so the chair is movable
by human force.
J
K
Figure 18
Figure 19
DO NOT use your chair while the drive motors are disengaged unless
you are in the presence of an attendant! DO NOT disengage the drive
motors when your chair is on an incline. The chair could roll down on
its own, causing injury!
To engage or disengage the free wheel feature:
1. Turn the free wheel levers outward, to engage the drive motors. (See Fig. 18)
2. Turn the free wheel levers inward to disengage the drive motors. (See Fig. 19)
It is important to remember that when your HS-6200 is in freewheeling
mode, the braking system is disengaged
Armrest
The height adjustable T-type armrest is provided as standard equipment on the chair.
Adjustment for the HS-6200 is facilitated by a thumbscrew fitted from the outside of the
armrest support at the lower end. To activate the thumbscrew simply loosen and remove
it from the locating hole. (See Fig 20.)
The Armrest is liftable by pulling the pin outward. (Figure 21)
Figure 20
Figure 21
11
HS-6200
User's Manual
1.The distance of your controller unit can be easily
changed for the desired position. To adjust it, loosen
L
the thumbscrew (L) and slide into or out of the controller
bracket.(Figure 22)
Figure 22
Seat
The C.T.M. chair features seat upholstery that can be tightened. While there should be no
adjustment necessary upon delivery of your new chair, over time stretch could occur.
Please contact the nearest C.T.M. dealer to have this taken care of if necessary. Below are
illustrations of the Seat Options which you can chose to install onto your chair according
to your own desires.
Figure 23
SPONGE SEAT
Figure 24
Figure 25
STANDARD SEAT
BREATHABLE
CUSHION SEAT & BACKREST
Replace worn or torn fabric immediately. Failure to do so may result in
a fall and severe injury to you.
Seat Belt
1. In driving condition, fasten the seat belt
as the picture illustrates.
2. Seat Belt can be unfastened by pressing
down the black button (O) (Fig. 26)
M
N
O
Figure 26
12
HS-6200
User's Manual
Leg Rests
The HS-6200 is equipped with a swing-away & detachable leg rests, which are height
adjustable. To adjust the height, remove the securing screws and nuts from each side
and slide the extension tube and leg rests up or down to the desired height. Retighten
the securing hardware as Fig. 27 shows
Figure 27
Options :
There are elevating leg rests as an option.
Never lift the wheelchair by the leg rests. These parts are detachable
and will not bear the weight of this chair. Lift this chair ONLY by nondetachable parts of the main frame.
Controller
1.Directional movement is attained by controlling the
P
joystick (P) ; move the joystick toward the direction
intended. HS-6200 is without turning limitation, it can
circle 360 degrees without problem.
Figure 28
Circuit Braker
1.When the electric circuit is overloading or malfunctioning
Q
the Circuit Braker will automatically shut off the main
power of the chair to ensure safety in performance.
Pressing down the button (Q) should restore mobility.
Figure 29
13
HS-6200
User's Manual
SAFE DRIVING TECHNIQUES
Driving your Chair
Before sitting on your chair, verify:
1. The chair is switched off.
2. Swing away the armrests and leg rests if appropriate.
3. The battery charger is disconnected from both the chair and the wall outlet.
Once on your chair, make sure that you are comfortably positioned and that the leg rests
and armrests have been adjusted to suit your needs. The position of the joystick should
be within reach to eliminate hand and arm exhaustion when driving.
To Begin :
1. Set the speed control of the chair to SLOW.
2. Press the "on / off" switch.
3. Allow two seconds to elapse before engaging the joystick. This is a safety feature to
prevent sudden starts.
4. Push the joystick gently forward applying a steady even pressure. The further you
push the joystick, the faster the chair will go. The chair will stop when you return the
joystick to the neutral or vertical position.
5. Directional control is achieved by gently swivelling the joystick in the direction you wish
to go. Pull back to reverse.
6. The controller can be programmed to give you the best feel for all driving situations
and only needs a light touch to respond.
In the case of an emergency, let the joystick go and the chair will come to a stop.
Safe Driving
1. Never drive at a speed greater than your ability to safely control your chair. Remember
that wet or loose surfaces need greater care and control.
2. Always turn the chair OFF when transferring on or off or while the chair is stationary
for long periods.
3. Avoid jerky stop / start motions as this will result in excessive current draw from the
batteries, increased tire wear and the rapid wearing of the gearbox and motors.
4. Keep your chair clean from sand and salt water.
Indoor / Outdoor Driving
When driving indoors keep the speed to a minimum to avoid the risk of collision.
For outdoor driving be cautious of wet surfaces, loose sand, large curbs and potholes.
A little practice will ensure you understand the capabilities of your chair and enable you
to overcome the most common obstacles encountered when driving.
14
HS-6200
User's Manual
Chair Operation on surfaces that require Special Care
When driving up or down ramps it is recommended that the user:
1. Visually checks to see if the angle of the slope is less than 10 degrees.
2. Checks to see that the ramp surface is roughened to prevent slippage.
3. Ensures that the ramp surface is correctly in line with the tires and is wide enough to
allow the tires to pass freely along the ramp.
If the ramp meets these conditions, it is recommended that the user drives the wheelchair
slowly up or down the ramp, ensuring that the chair is driven in the centre of the ramp
tracks. If possible, have an assistant monitor the chairs' progress, and prevent tipping
of the chair by holding the push handles at the back of the seat.
If the ramp does not meet these conditions, it is recommended that alternative
methods for climbing and descending be found.
Chair Response
Should the chairs' response not be to your satisfaction, ask your dealer to adjust the
program to a level at which you are comfortable. This program can be altered at
anytime to either increase the response rates in line with your improved motor skills
or to lower the rates to a level at which you feel comfortable and in control.
Curbs
It is recommended that before the user attempts to climb or descend a curb that the user
visually checks the height of the curb to ensure that it does not exceed 1.1" in height.
If the curb height is less than 1.1", the user should approach the curb at right angles to
the curb line at a slow speed, climb or descend the curb slowly so as to keep the chair
under control. When climbing the curb, the user may find it easier to reverse the chair
up the curb.
If the curb height is greater than 1.1", it is not recommended that the user climb or descend
the curb.
Steep Slopes
When the power wheelchair is to be operated up and down steep slopes, it is recommended
that the user:
1. Visually checks to see if the angle of the slope is less than 10 degrees.
2. Checks that the slope surface is roughened to prevent slippage.
If the slope meets these conditions, it is recommended that the user approach the slope at a
slow speed, keeping the chair under control at all times. It may be preferable to track across
the slope so as to decrease the steepness of the descent providing that the surface of the
slope is wide enough and suitable to prevent slippage.
15
HS-6200
User's Manual
If the slope does not meet these conditions, it Is recommended that
the user does not climb or descend the slope.
BATTERIES AND CHARGING
When your batteries are fully charged you should have sufficient power to give you all
the mobility required in a day. It is important that you understand how your batteries and
charger work. Batteries must be charged before using the power chair for the first time
and are recommended to be charged up to 10 - 14 hours after each day's use.
Charging the Batteries
1.
2.
3.
4.
5.
Batteries should be charged every night in a well ventilated room.
DO NOT place the power wheelchair near radiators or open fireplaces while charging.
DO NOT smoke or permit open flames in the immediate vicinity.
Turn the chair controller power off before charging.
It is advisable that the batteries be charged for a minimum of 10 hours per night to ensure
full battery storage capacity. The battery charger is an automatic current limiting device
and will shut off when the batteries are fully charged.
Charging the batteries :
1. Position HS-6200 power chair next to a standard wall outlet.
2. Connect the battery charger to the wheelchair input battery charging socket, which is
located on the front of the controller.
3. Connect the battery charger to a standard wall power outlet.
4. Switch the power on.
During the recharge :
1. While the batteries are being recharged, a red light will appear on the battery charger,
indicating that the power is connected and charging is in progress.
At the end of the recharge cycle:
1. A green light will appear on the charger. This indicates that the batteries are fully
charged and ready for use.
2. If fitted, the battery charge level indicator on the controller should also show a full charge
when switched on.
When do the batteries need recharging?
When the batteries fall below 20% of the maximum charge level, the serles of lights
on the controller will flash.
1. Do not use batteries other than the recommended type for your chair and
never use a charger other than the one supplied for that purpose.
2. If the chair is not used for a long period of time arrange to have the batteries
charged for at least one day (10 hours) every month, minimum.
3. Periodically, check that the battery terminals are clean and the connections
are tight. Smear a thin film of petroleum jelly on the terminals to guard
against corrosion. Always wash your hands after handling batteries.
16
HS-6200
User's Manual
Replacing the batteries
CAUTION ! - If you have doubts about your ability to lift any components,
it is recommended that you seek qualified dealer so as to
avoid injury.
1. Turn the power off.
2. Disconnect the battery connection plug at the front of the battery tray.
3. Release the securing belt holding the battery box.
4. Disconnect the battery connection cables located in the battery box.
5. Lift the rear battery out of the battery box by using the lifting strap.
6. Slide the front battery to the rear of the battery box and remove the battery
as in step 5.
7. Undo the terminal lugs, noting the polarity of the lugs. Remove the wiring loom.
8. Repeat step 7 for the other battery.
9. Inspect the terminals on the wiring loom and the lugs on the replacement batteries
to make sure they are clean. If they are not, clean with a warm solution of bicarbonate
of soda and water. It is important that you wash your hands afterwards.
10. Connect the terminal lugs on the wiring loom to the new batteries, observing the
polarity of the lugs as noted before.
11. Place the new batteries back into the battery box and rejoin the connectors.
12. Replace the battery box lid and secure the retaining belt.
13. Reconnect the power cable.
For maximum performance it is recommended that you replace both batteries
at the same time
17
HS-6200
User's Manual
TIRE
You should inspect the tires frequently for damage, the presence of foreign bodies,
unusual wear and sufficient tread depth. Tread depth should if possible not be allowed
to drop below 1/16". If replacement tires are needed, please contact the nearest C.T.M.
dealer.
Front wheels :
8" solid tires.
Rear wheels :
13" solid tires.
Follow these easy steps to replace the tire:
1. Use an ratchet and socket to remove the drive wheel screw from the centre hub of
the wheel. See Fig 30.
2. Pull the wheel off of the axle.
3. Separate the tire from the rim.
4. Remove the old tire and replace it with a new tire.
5. Slide the wheel back onto the shaft.
6. Install the drive wheel nut into the centre hub and verify the key is lined up with axle
and wheel. Then tighten to secure it in place.
Figure 30
18
HS-6200
User's Manual
MAINTENANCE, AND CLEANING
An electric wheelchair needs some basic attention to ensure it provides reliable service.
We recommend that the user ensures that the power wheelchair is checked regularly for
maintenance requirements and receives a thorough, annual maintenance check up.
Annual Maintenance
We recommend that the chair has at least one full service per year from an authorized
dealer. This will ensure that your power chair is functioning properly and also helps
prevent future complications. This should include:
1.
2.
3.
4.
5.
Checking
Checking
Checking
Checking
Checking
the
the
the
the
the
tires.
batteries and terminals.
controller program for the user's needs.
frame.
upholstery condition.
Regular Maintenance and Cleaning
1. Avoid knocking or bumping the controller, especially the joystick.
2. Avoid prolonged exposure of your power chair to extreme conditions, such as heat,
cold, or moisture.
3. Keep the controller clean.
4. Check that all controller connectors are tight and secured properly.
5. Never hose off your power chair or place it in direct contact with water.
6. Keep the upholstery and frame clean by wiping with a soft cloth, particularly after
driving through wet, sandy or muddy conditions. Do not use harsh abrasive materials
when cleaning. Do not apply liquid cleaners or solvents directly to the control box,
battery charger or any electrical connections.
7. Keep wheels free from lint, hair, sand and carpet fibres.
8. Lightly oil axle pin, wheel axles and bearings once every three months, if necessary.
9. Inspect the tires. Tread depth should not be allowed to drop below 1/16".
10. Use only recommended batteries and have batteries changed by Qualified Dealer if you
have doubts about your ability to lift the components.
11. Charge batteries regularly. Make sure the charger lead plugs are engaged properly
in the sockets. Do not disconnect by pulling the cord.
12. With the controller turned off, check the joystick. Make sure it is not bent or damaged
and that it returns to the center when you release it. Check the rubber boot around
the base of the joystick for damage. Visually inspect the boot. Do not handle or try
to repair it. See your authorized dealer for any questions.
13. Visually inspect the controller harnesses. Make sure that they are not frayed, cut or
have any wires exposed. See your authorized dealer if there is a problem with any
of these harnesses.
14. Ensure that all parts of the controller system are securely fastened to your HS-6200.
Do not over tighten any screws.
19
HS-6200
User's Manual
TROUBLESHOOTING
Here are some suggestions about solving problems you may have with your power chair.
There are 10 LED Self-Diagnostic Warning Lights on the Control Panel. To check the
Self-Diagnostic Warning Lights, turn the power chair on and count the number of flashes.
Number of
Flashes
Solution
1 bars
The battery needs charging or there is a bad connection to the
battery. Check the connections to the battery. If the connections
are good, try charging the battery.
2 bars
The left hand motor* has a bad connection. Check the connections
to the left hand motor.
3 bars
The left hand motor* has a short circuit to a battery connection.
Contact your service agent.
4 bars
The right hand motor* has a bad connection. Check the connections
to the right hand motor.
5 bars
The right hand motor* has a short circuit to a battery connection.
Contact your service agent.
6 bars
The wheelchair is being prevented from driving by an external signal.
The exact cause will depend on the type of wheelchair you have, one
possibility is the battery charger is connected.
7 bars
A joystick fault is indicated. Make sure that the joystick is in the
center position before switching on the control system.
8 bars
A control system fault is indicated. Make sure that all connections
are secure.
9 bars
The parking brakes have a bad connection. Check the parking brake
and motor connections. Make sure the control system connections
are secure.
10 bars
An excessive voltage has been applied to the control system.
this is usually caused by a poor battery connection.
Check the battery connections.
If the programmable parameter, Motor Swap, has been changed then left and right hand
references in this table will need transposing.
20
HS-6200
User's Manual
Other Problems:
•Power chair will not move when the power is turned on:
1.Check the Battery Level Indicator on the joystick. All the LED lights should be on.
2.Check the Self-Diagnostic Warning Light. It should be steady. If it is flashing, see the
chart on page 20 for the problem identification.
3.Check all electrical connections to be sure they are tight.
4.Verify the batteries are connected correctly. Refer to "Installation of Batteries" on page 10.
5.If none of these suggestions correct the problem, contact your authorized dealer.
•If charging your power chair over 14 hours and the light on the charger does not change
to green, then contact your authorized dealer.
Please note that your power chair is equipped with a controller that constantly checks the
drive system for a safe and enjoyable ride. If an error occurs, the Battery Level Indicator
will provide you an indication of the problem by way of flashing lights.
We thank you again for choosing C.T.M. for your power chair. C.T.M. offers exceptional,
uncompromised quality, for better mobility.
"When you compare, the decision will be obvious: C.T.M."
21
HS-6200
User's Manual
SPECIFICATION
SPECIFICATIONS
HS-6200
HS-6200N
Overall Length
42.3"
41.1"
Overall Width
24"
23.2"
Overall Height
35.4"
35.4"
Wheels: Front
7.4"
8"
Wheels: Middle
N/A
N/A
Wheels: Rear
13"
13"
156.3 lbs
154.8 lbs
Max. Speed
5 mph
5 mph
Weight Capacity
280 lbs
280 lbs
1.8"
1.8"
10 degree
10 degree
Curb Climbing
1.1"
1.1"
Turning Radius
38.6"
36.2"
Electro-Mechanical
Electro-Mechanical
17"
16"
Weight w/ Batteries
Ground Clearance
Grade Climbable
Brake
Seat Width
Drive Train
2-Motor Rear-Wheel Drive
60 lbs
60 lbs
420W 4600 r.p.m
420W 4600 r.p.m
11.9 Miles
11.9 Miles
Battery
(2) 12V . 36Ah
(2) 12V. 36Ah
Charger
5A Off Board
5A Off Board
Electronics
PG-VSI
PG-VSI
Seat Type
Padded, Breathable Ballistic
Nylon Back Rest
Battery Weight
Motor Size
Travel Range
*Subject to change without notice.(Issue A)
22