Electrolux EWM2500 Service manual

SERVICE MANUAL
WASHING
Washing machines,
Toploader
© AEG Hausgeräte GmbH
Muggenhofer Straße 135
D-90429 Nürnberg
Germany
Publ.-Nr.:
599 52 74 52
685
EN
LCD-appliance
EWM 2500, 2100
ENV 06
TC3 low, TC3 high, TC2
ELECTROLUX
Fax +49 911 323 1022
DGS-TDS-N
12.06
Edition
CONTENTS
Control Panel / Multifunctionsdisplay LCD....................................................................... 3
-
10
Push Buttons................................................................................................................. 11
-
13
Programselector / Programme ..................................................................................... 14
-
15
-
18
Drum movements / Spin Profiles .................................................................................. 31
-
33
Function of the FUCS .................................................................................................... 34
-
35
-
45
Circuit Diagram ............................................................................................................. 49
-
52
Program ........................................................................................................................ 53
-
59
Buzzer / Extra rinse cycle / Child safety ....................................................................... 16
Functions of the System ............................................................................................... 17
Connection electronic ................................................................................................... 19
Electronic Module .......................................................................................................... 20
Door Lock ...................................................................................................................... 21
DSP Function (Drum Self Position) .............................................................................. 22
Float switch / Inlet valve with flow-meter-sensor ........................................................... 23
Water Inlet Valve for 3-chamber detergent box ............................................................. 24
Water Distributor ........................................................................................................... 25
Analogic pressure switch .............................................................................................. 26
Heating element ........................................................................................................... 27
Heating Circuit ............................................................................................................... 28
Drain pump / Circulation pump / Motor .......................................................................... 29
Motor / Motor control board ............................................................................................ 30
Foam Detection ............................................................................................................. 36
Service Program ........................................................................................................... 37
Demo Program ............................................................................................................. 46
Electronic-Test .............................................................................................................. 47
Operating time ............................................................................................................... 48
Changes ........................................................................................................................ 60
DGS-TDS-N 12.06 R.B.
© Electrolux
-2-
599 52 74 52
EN
Control Panel
Version TC3 low (Electrolux-design)
Spin
Cotton
Normal
Eco
Drain
Soft rinse
Synthetics
Prewash
Delicates
Jeans
Easy iron
Wool
Silk
Handwash
Dessous
I
A
B
C
D
E
H
G
Delayed start
Start, Pause
Multifunctionsdisplay LCD
Options
Extra rinses
F
E
D
F
G
H
I
Prewash
Spin
Temperature
Programselector
C
Temperature
C
B
A
Multifunctionsdisplay LCD
C
A
B
B
A
Display
Child safety
DGS-TDS-N 12.06 R.B.
© Electrolux
-3-
599 52 74 52
EN
Display
Function:
delayed start selection with the delayed start button
cycle duration and remaining time indicated in hours and minutes 2.08 (e.g. 2h08min)
information on error codes (e.g. E10)
End of cycle when 0.00 is indicated.
Standby
Function:
After 10 minutes of standby in the pre-selection position or at the end of the cycle, the light of the
Display switches off and the LED Start/Pause flashes slowly.
Pressing any button or rotating the selector, the appliance returns to the normal status (following
model MCF-file).
Child safety
Function:
All keys are blocked (see page 16).
Temperature
Function:
Is lit when heater is selected.
DGS-TDS-N 12.06 R.B.
© Electrolux
-4-
599 52 74 52
EN
Control Panel
Version TC3 high (Electrolux-design)
Spin
Cotton
Normal
Eco
Drain
Soft rinse
Synthetics
Prewash
Delicates
Jeans
Easy iron
Wool
Silk
Handwash
Dessous
I
A
B
C
D
E
H
Time Manager
Start, Pause
Multifunctionsdisplay LCD
Delayed start
Extra rinses
G
F
F
G
H
I
E
D
C
B
A
Prewash
Spin
Temperature
Programselector
Multifunctionsdisplay LCD
E
A
B
C
D
C
B
Display
Cycles
Child safety
DGS-TDS-N 12.06 R.B.
D
E
© Electrolux
-5-
A
Temperature
Time Manager
599 52 74 52
EN
Display
Function:
delayed start selection with the delayed start button
cycle duration and remaining time indicated in hours and minutes 2.08 (e.g. 2h08min)
information on error codes (e.g. E10)
End of cycle when 0.00 is indicated.
Cycles
washing
rinse
drain
spin
Standby
Function:
After 10 minutes of standby in the pre-selection position or at the end of the cycle, the light of the
Display switches off and the LED Start/Pause flashes slowly.
Pressing any button or rotating the selector, the appliance returns to the normal status.
Child safety
Function:
All keys are blocked (see page 16).
Temperature
Function:
Is lit when heater is selected.
DGS-TDS-N 12.06 R.B.
© Electrolux
-6-
599 52 74 52
EN
Time Manager
Program
Cotton
Easy care
Delicate
Soiling degree
intensiv
X
normal
X
X
X
daily
X
X
X
quick
X
X
X
extra quick
X
super quick
X
X
X
Function:
The washing cycle is extended or reduced depending on the selected degree of soiling level.
e.g. Cotton 60°C
DGS-TDS-N 12.06 R.B.
© Electrolux
-7-
Cotton 60°C + intensiv
2h 10min
Cotton 60°C + normal
2h 00min
Cotton 60°C + daily
1h 40min
Cotton 60°C + quick
1h 30min
Cotton 60°C + extra quick
1h 20min
Cotton 60°C + super quick
1h 00min
599 52 74 52
EN
Control Panel
Version TC2 (Electrolux-design)
Spin
Cotton
Normal
Eco
Drain
Soft rinse
Synthetics
Prewash
Delicates
Jeans
Easy iron
Wool
Silk
Handwash
Dessous
I
A
B
C
D
H
G
Time Manager
Start, Pause
Multifunctionsdisplay LCD
Delayed start
F
E
D
C
B
A
Prewash
Spin
Temperature
Programselector
F
G
H
I
Multifunctionsdisplay LCD
G
A
B
C
D
F
E
D
Cycles
Display
Time Manager
Child safety
DGS-TDS-N 12.06 R.B.
E
F
G
© Electrolux
-8-
C
B
A
Options
Spin
Temperature
599 52 74 52
EN
Display
Function:
delayed start selection with the delayed start button
cycle duration and remaining time indicated in hours and minutes 2.08 (e.g. 2h08min)
information on error codes (e.g. E10)
End of cycle when 0.00 is indicated.
Cycles
prewash
washing
Symbol
Status
ON
OFF
Standby
rinse
drain
spin
process
cycle is running (lid closed)
lid not closed
Function:
After 10 minutes of standby in the pre-selection position or at the end of the cycle, the light of the
Display switches off and the LED Start/Pause flashes slowly.
Pressing any button or rotating the selector, the appliance returns to the normal status.
Child safety
Function:
All keys are blocked (see page 16).
Option
Function:
Depending on model there can be various additional features.
Spin
Function:
A corresponding symbol is indicated depending on the selected speed.
Animated spiral symbol during spin cycle.
Night cycle- and Rinse hold-Symbol
Temperature
Function:
A corresponding symbol is indicated depending on the selected temperature.
The temperature is indicated in degree Celsius.
DGS-TDS-N 12.06 R.B.
© Electrolux
-9-
599 52 74 52
EN
Time Manager
Program
Cotton
Easy care
Delicate
Soiling degree
intensiv
X
normal
X
X
X
daily
X
X
X
quick
X
X
X
extra quick
X
super quick
X
X
X
Function:
The washing cycle is extended or reduced depending on the selected degree of soiling level.
e.g. Cotton 60°C
DGS-TDS-N 12.06 R.B.
© Electrolux
- 10 -
Cotton 60°C + intensiv
2h 10min
Cotton 60°C + normal
2h 00min
Cotton 60°C + daily
1h 40min
Cotton 60°C + quick
1h 30min
Cotton 60°C + extra quick
1h 20min
Cotton 60°C + super quick
1h 00min
599 52 74 52
EN
Push Buttons
Spin deselection button
Function:
By pressing this key, you can reduce spin-dry speed step by step down to zero, to rinse hold or to
night cycle.
Reduces the spinning speed of all spin-dry cycles.
1500
1400
1400
1300
1200
1200
1200
1200
1000
1000
1000
1000
900
800
800
800
800
800
700
600
600
600
600
600
600
400
400
400
400
400
400
0
0
0
0
0
0
Rinse hold
Rinse hold
Rinse hold
Rinse hold
Rinse hold
Rinse hold
Night
Night
Night
Night
Night
Night
Cycle
Cycle
Cycle
Cycle
Cycle
Cycle
Temperature button
Function:
To activate the temperature button it is necessary to select a program.
By pushing this button the washing temperature can be reduced to 0°C step-by-step.
adjust
temperature
95°C
60°C
50°C
40°C
30°C
0°C
Start/ Pause button
Function:
The selected program is activated by pressing the start/pause button.
The LED start/pause on.
If the cycle is to be paused, press the start/pause button.
Start/ Pause-LED blinks. The program interrupt.
This is not possible after a program run time of 10 min..
The LED-lid or LED-add washing off.
LED
status
(green) ON
(green) Flashing
start/pause
(red) Flashing
OFF
ON
lid (green)
OFF
add washing
ON
(green)
OFF
process
cycle is running (lid closed)
cycle in pause position
additional option key pressed, after program start. Err in display.
lid can be opened, it is possible to pause the cycle
cycle running, no possibility to pause
lid can be opened, it is possible to pause the cycle
cycle running, no possibility to pause
Delayed Start button
Function:
Hold the “delayed start” button pressed, the start time will be indicated in the display and counted
up, the start time can be selected max. from 0h, 30', 60', 90', 2h - 20h.
The start time is counted down hour by hour, from 90 min in steps of 30 minutes,
from 30 min in steps of minutes.
Change of delayed start:
- switch off the programselector
- select a new program again
DGS-TDS-N 12.06 R.B.
© Electrolux
- 11 -
599 52 74 52
EN
Options
The selection of the options is to be carried out after switching on the appliance and setting the desired
programme with the selector and before pressing the start/pause button.
DGS-TDS-N 12.06 R.B.
© Electrolux
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Half-load
X
X
X
X
X
X
no spin
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Reduced spin speed
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Super quick
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Quick
X
X
X
X
X
X
X
X
X
X
Light
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Daily
X
X
X
X
X
X
X
X
X
X
X
Normal
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Intensiv
X
X
X
X
X
X
Eco
X
X
X
X
Easy iron
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Extra rinse
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bleach
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Stains
Night cycle
90°C
60°C
50°C
Cotton
40°C
30°C
cold
60°C
50°C
Synthetic
40°C
30°C
cold
40°C
Delicates
30°C
cold
40°C
Wool
30°C
cold
60°C
50°C
Easy iron
40°C
30°C
cold
40°C
Blanket
30°C
60°C
50°C
Jeans
40°C
30°C
cold
40°C
Shoes
30°C
cold
40°C
Lingerie
30°C
cold
30°C
Silk
cold
40°C
Baby, Sport
30°C
intensiv
cold
Sport light, Min 30°C
Sanitär
90°C
5 Shorts
30°C
MIX 40°-60°
40°C
90°C
60°C
Hygiene +
50°C
40°C
60°C
Gras
50°C
40°C
Express
60°C
Sensitiv Plus
60°C
Quick
30°C
Soak
30°C
Rinses
softener
Conditioner
Drain
Spin
Gentle spin
Rinse-hold
Compatibility with programmes
Programmes
Pre-wash
Options
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
- 12 -
599 52 74 52
EN
Function:
Rince hold
The program is finish with water in the drum.
In order to continue a program afterwards, you first have to select a separate draining or spinning.
Function:
Night Cycle
The number of rinces are increase cotton/cotoured from three rinces to six rinces and
synthetic from three rinces to four rinces.
All rinces are without a spinphase.
The programm is stopped in a rinse hold.
In order to continue a program afterwards, you first have to select a separate draining or spinning.
Switches off the buzzer ( if configured)
Function:
Pre-Wash
It is heated up to max. 30 ° C.
Can't be combined with the programe wool, silk and sport 30.
Function:
Stains
The selected temperature however must be >=40°C.
Separate rinsing in of stain remover through the pre-wash chamber, approx. 1.2 ltrs.
Can't be combined with the pre-wash function.
Extends the cycle duration in the main wash by 5 minutes after the first heating to 40°C.
Function:
Extra rinse
Two additional rinse cycles are added in the cycle cotton / coloured.
One additional rinse cycle are added in the cycles synthetics, delicate fabrics and silk.
No intermediate rinse, except after the last rinse cycle.
Function:
Easy Iron 40°
With cotton/coloureds programmes:
No intermediate spin-dry cycle.
3 additional rinse cycles.
Pulse spin-dry
Additional loosening phase after spin-drying
-
With synthetics programmes:
Reduced wash temperature
Prolonged wash time and prolonged cooling phase
One additional rinse cycle
Additional loosening phase after spin-drying
Function:
Energy Saving
The washing temperature in the programs:
E90°C is reduced to 67°C, the max. temperature kept constantly for a certain period of time.
E60°C is reduced to 40°C, the max. temperature kept constantly for a certain period of time.
E40°C is reduced to 40°C, the max. temperature achieved for a short moment.
Can't be combined with the quick function.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 13 -
599 52 74 52
EN
Programselector
Depending on the model, the electronic may include
a programselector with 15 or 21-positions.
The programselector includes the “on/off” function
and the wash programs.
Programme
Jeans
Function:
The cycle includes a main cycle, five rinse cycles. (1. and 2. rinses without intermediate spins
and 3., 4., 5. rinses with intermediate spins max.1200 1/min).
The load amount is 3kg.
Can be combined with the Night Cycle Pre-wash and Spin deselection button.
Shoes 30°, 40°
Function:
The program consists of a main wash, three rinses without intermediate spins but with an
end spin. (1000 1/min).
It is heated up to 40 °C.
Can be comdined with the Quick, Extra rinse, Night Cycle, Pre-wash, Soaking and Spin
deselection button.
Silk 30°
Function:
The program consists of a main wash, three rinses without intermediate spins but with an
end spin. (700 1/min).
Washing time during main wash is 10 min.
The load amount is 1kg.
Baby 30°, 40°
Function:
The program consists of a main wash, three rinses with higher water levels without intermediate
spins, but with an end spin. (700 1/min).
The load amount is 2kg.
Sanitär 90°
Function:
The program consists of a main wash, three rinses with intermediate spins but with an
end spin. (1200 1/min).
Washing temperature during main wash is kept constantly to 85° for 10 min.
The load amount is 5,5kg.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 14 -
599 52 74 52
EN
Dessous 30°, 40°
Function:
The program consists of a main wash, three rinses without intermediate spins but with an
end spin. (900 1/min).
The load amount is 1Kg.
Blanket 30°, 40°
Function:
The program consists of a main wash, three rinses with higher water levels
(20ltr.) intermediate and end spin. (650 1/min).
The load amount is 2,5kg.
Soak
Function:
The soaking period begins with pre-wash and soaks for about the next 30 minutes.
Can't be combined with the function pre-wash.
It is heated up to 30 °C.
A short spin cycle is performed in the cycles COTTON and SYNTHETICS, before passing on to the
main wash.
You can prolong soaking time for max. 0h, 30', 60', 90', 2h - 10 h using the „Start preset“ key.
After pressing the start key, the duration of the cycle is displayed by hours and minutes.
Sport light 30°
Function:
The program consists of a main wash, two rinses with higher water levels without intermediate
spins, but with an end spin. (700 1/min).
The load amount is 2kg.
Sport intensiv 30°, 40°
Function:
The cycle consists of prewash, higher water level, heating to 30° and spin cycle to 650 1/min, one
main wash, two rinse cycles without intermediate spin with higher water level but with final spin
(900 1/min).
The load amount is 2,5kg.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 15 -
599 52 74 52
EN
Buzzer, Extra rinse cycle, Child safety
1
2
3
4
5
6
Activation and deactivation of the buzzer:
Function:
Depending on the model, the electronic may include a buzzer.
Switch off the appliance.
Hold buttons 3 and 2 pressed simultaneously and turn the program selector one position to the
right. The buzzer is activated.
You can deactivate the buzzer by repeatedly pressing the key combination.
Activation and deactivation of the extra rinse cycle:
Function:
If no extra rinse key is available, you can select extra wash.
This button is effective in the cycles cotton/coloured wash, synthetics and delicate fabrics.
Two additional rinse cycles are added.
No intermediate rinse, except after the last rinse cycle.
Switch off the appliance.
Hold buttons 4 and 2 pressed simultaneously and turn the program selector one position to the
right. The extra rinse is activated.
You can deactivate extra wash by repeatedly pressing the key combination.
Activation and deactivation of the child safety:
Function:
The child safety function can be activated at the start of the program and also after
the program has started.
Press keys 4 and 3 simultaneously and hold until a symbol appears on the LCD.
The option is activated, the initiated wash program runs normally through and on
completion any further function of the appliance is disabled. The option remains saved when the
appliance is turned off.
You can deactivate child safety by repeatedly pressing the key combination.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 16 -
599 52 74 52
EN
Functions of the System
Electronic EWM2100 with universal motor AC
2
3
4
1
5
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
6
7
8
9
10
electronic module
motor
heating element
door security
drain pump
circulation pump
NTC-sensor
inlet valve with flow-meter-sensor
analog pressure switch
drum self position (DSP)
DGS-TDS-N 12.06 R.B.
© Electrolux
- 17 -
599 52 74 52
EN
Functions of the System
Electronic EWM2500 with asynchronous three-phase motor
2
3
4
5
1
6
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
7
8
9
10
11
electronic module
motor control board
motor
heating element
door security
drain pump
circulation pump
NTC-sensor
inlet valve with flow-meter-sensor
analog pressure switch
drum self position (DSP)
DGS-TDS-N 12.06 R.B.
© Electrolux
- 18 -
599 52 74 52
EN
Connection cable electronic
Electronic EWM2100
1
2
3
5
4
7
8
10
11
6
1.
2.
3.
4.
5.
6.
7.
8.
multifunctionsdisplay LCD
drum self position (DSP)
analogic pressue switch
NTC-sensor, Inlet valve with flow-meter-sensor
motor, drain pump
Power supply 230V
heating element
door security
Electronic EWM2500
1
2
3
4
7
5
8
9
6
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
multifunctionsdisplay LCD
drum self position (DSP)
flow-meter-sensor
analogic pressue switch
NTC-sensor, Inlet valve
Power supply motorcontrol board
motorcontrol board +5V, +15V
drain pump, circulation pump
Power supply 230V
heating element
door security
DGS-TDS-N 12.06 R.B.
© Electrolux
- 19 -
599 52 74 52
EN
Electronic Module
The electronic module, including the μP, controls various functions and is placed in a protective housing.
It is the communication interface between the user and the appliance.
It consists of:
-
The option buttons and the multifunctiondisplay LCD.
The programselector with 15 or 21-positions.
The time display and the alarm identification.
The “Start/Pause” button.
Functions:
Taking data of the selected cycle programs through the module.
Water level control (antifoam, overflow level) in the tub; the level is recognized by the analog
pressure switch.
Cycle temperature control by a NTC sensor.
Power supply of the heating element.
Power supply of the drive motor (EWM2100) and control of its speed by the tachymetric generator.
Control of the motor control board (EWM2500).
Control of water inlet valves.
Control of drain pump, circulation pump, door lock and DSP (drum self position).
In case of a power failure the module saves the just paused cycle.
-
When the power supply to the appliance is restored again, the cycle starts where the program was
paused.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 20 -
599 52 74 52
EN
2=N
3 = impulse electronic
4=L
5 = electronic J1-2
Door Lock
5
4
3
2
pin Fe
magnetic coil
PTC bimetal
lever
make-and-break
contact
tooth lock washer
locking part
When closing the lid the door lock gets an impulse from the electronic by contact 3. The impulse feeds
the magnetic coil over the PTC resistor. This moves the lever down and the tooth lock washer is
forwarded by another tooth. This can be heard by a click. The locking part is unlocked, the lid is closed.
When opening the lid, e.g. with the start/pause button or at the end of the cycle, the door lock gets two
impulses from the electronic. The tooth lock washer is moved twice. Only because of the second impulse
the lid can be opened immediately.
The second impulse unlocks the locking part mechanically through the tooth lock washer.
Why two impulses?
The door lock is controlled by a triac which is on the main circuit board. If there is a triac short circuit, the
electronic sends an impulse to the door lock. The customer could open the appliance, if the second
impulse was not required.
If there is a power failure during a wash cycle, the door lock requires approx. 2 min until the lid can be
opened. During this time the PTC bimetal cools down and the locking part opens.
Circuit Diagram
2
4
Security:
(see page Service - Program fault display E40)
DGS-TDS-N 12.06 R.B.
© Electrolux
5
3
- 21 -
599 52 74 52
EN
DSP (Drum-Self-Position)
Control ( check ) the DSP-Function:
1.
Remove the side panel, switch on the appliance
- Turn the drum to the right position ---> LED on
- Turn the drum over the right position ---> LED off
2
Remove the two plugs from the DSP and check
the resitance of the reed relay.
- Turn the drum to the right position
---> > 0Ω
- Turn the drum over the right position ---> 0Ω
3
The drum is still in the right position.
Now measure the voltage. 5-6V DC
- If there is no voltage ---> Cable,
Main electronic board
is defective
4.
Check the In / Output electronic in the customers
service test program.
- LED on ---> In / Output electronic OK.
- LED off ---> In / Output electronic defective.
Magnet
Reed - Switch
Connections
Function:
The reed relay is closed if the metalic sheet, located on the pully, isn't between the magnet and the reed
relay. If the position of the metalic sheet is between those parts the contact of the reed relay is opened.
To mount the pulley in the correct way, you have to take care about following items:
The metal sheet located on the pulley should be in the drum self positioning device, if the door of the
drum is in the upper postion. The DSP is supplied with 5-6 V DC by the main board.
Condition drum positioned:
Reed contact opened, LED-Drum positioned illuminated, 5-6V DC.
Condition drum out of postion:
Reed contact closed, LED-Drum positioned not illuminated, 0V.
If the washing cycle is interrupted by the start pause button the drum has to be postioned within 10 sec.
During this time 2-3 attempts can be excecuted.If the drum isn't positioned during this time, the lid of the
appliance is released and can be opened. The LED drum positioned is not illuminated.
At the end of the cycle the positioning phase is 2 min until time out is reached.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 22 -
599 52 74 52
EN
Float switch
Micro-switch
The float switch is made of a housing with a micro
switch and a float body.
Function:
The float switch is located in the bottom tray. The
bottom tray is constructed in a way that the water is
gathering in the area of the float switch in case of
leaky components (tub, hoses, etc.). The float body
comes up and switches a micro switch.
This selects the drain pump, the existing water in
the tub is drained. The inlet valve is switched off.
Float
Styropor
Inlet valve with flow-meter-sensor
Coil
Turbine 2 with magnet
Turbine 1
Flow control regulator
Reed-Switch
Sieve
Depending on the type of appliance, the automatic washer can be equipped with a 2-fold inlet valve with
or without flow-meter-sensor.
Function:
The inlet valve includes a flow meter sensor. The flow meter sensor emits electrical pulses of 5V to the
main electronic. This is enabled by a magnet which opens and shuts a reed contact. The magnet is
located on a movable turbine 2. Because of the water pressure the turbine rotates and thus gives
impulses to the main electronic. The water pressure of > 1 bar is limited by the volume regulator to 5.5 l/
min +15%/-15%.
(see Page Service - Program fault display EC0)
DGS-TDS-N 12.06 R.B.
© Electrolux
- 23 -
599 52 74 52
EN
Water Inlet Valve for 3-chamber detergent box
Main wash
Softener
Pre wash
6
4
5
3
2
2
1
1
2
3
4
5
6
*)
-
connection water inlet hose
inlet valve, 2-fold
hose for pre-wash
hose for main wash
water distributor
hose for fluff filtre
Attention!
The simultaneous filling through hoses 3 and 4 provides the fill-in through the softener chamber.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 24 -
599 52 74 52
EN
Water Distributor
Water inlet
main wash chamber
Water inlet
pre wash chamber
Main wash chamber
DGS-TDS-N 12.06 R.B.
© Electrolux
Pre wash chamber
- 25 -
599 52 74 52
EN
Analogic pressure switch
The analogic pressure switch controls the water level in the tub, it is directly connected to the electronic
modul.
If the pressure switch does not work correctly, the programm in progress is cancelled:
1.
2.
3.
4.
5.
6.
7.
8.
Pressure switch hose connection
Diaphragm
Coil (self)
Electronic circuit (oscillator)
Magnet
Spring
Adjusting screw
Connector
Kontakt 1 = Out
Kontakt 2 = GND
Kontakt 3 = 5V DC
When the tub is full, the pressure inside the hydraulic circuit acts on the diaphragm which moves the
magnet inside
the coil.
This moving modifies the inductance of self and consequently the frequence delivered by the scillatory
circuit. the μP, after frequence reading, recognizes the water level inside the tub. (see Page Service Program fault display E30)
Frequence delivered follow the pressure (± 50 Hz)
DGS-TDS-N 12.06 R.B.
© Electrolux
- 26 -
599 52 74 52
EN
Heating element
Connection:
Power:
Fuse:
230V; 50Hz;
1950W
10A
The heating element is supplied with power directly from the control
electronics by means of a relay. For security reasons, 2 switching
contacts of the pressure switch are connected in series. The
switching positions are monitored by control electronics via 2 control
lines.
1.
2.
3.
4.
Heating element
Temperature fuse
NTC-sensor
Connection
Check of insulation resistance with the heating
Wash a cycle for approx. 10 minutes. Switch off the appliance, unplug
the plug and remove the side panel.
Draw off the connecting lines from the heater.
Measure the resistance between heating (depending on connection)
and mass.
Resistance > 200 kOhm —> heater OK.
Resistance < 168 kOhm —> error E68
DGS-TDS-N 12.06 R.B.
© Electrolux
- 27 -
599 52 74 52
EN
Heating Circuit
The cycle temperature is fixed by the μP depending on the selected program.
The temperature control is guaranteed by the μP through the NTC temperature sensor. The temperature
sensor reduces its resistance according to the temperature increase.
The reduction in the ohmio value of the temperature sensor is detected by the μP; as soon as the
selected temperature is reached the power supply to the heating element will be paused.
The NTC sensor is integrated in the heating element.
NTC-Sensor
1.
2.
3.
4.
NTC resistance
Metallic casing
Connections
Plastic casing
To check the NTC sensor function you can measure the ohmic resistance between the contacts
J9/8 and J9/9.
Variations of NTC resistance
Temperature (°C)
25
40
60
80
Resistance (Ohm)
4815
+- 207
2563
+- 102,5
1196
+- 26,31
602
+- 19,89
Security
-
The μP will be break off if an anomaly on the termistance circuit is detected :
cut or short-circuit. (see Page Service-Program fault display E70)
The heating phase is not executed.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 28 -
599 52 74 52
EN
Drain pump / Circulation pump
The drain pump and circulation pump is directly controlled via triac from the control electronics.
Motor
Electronic EWM2100
The motor is directly phase-controlled via triac from the control electronics.
Relays K2, K3 are responsible for commuting the sense of rotation.
Field switching (if any) is controlled by relay K4.
Speed is monitored by tachometer generator g1 and controlled by control electronics.
Integral overheat protection disconnects the motor from power supply at 115°C.
Connection:
Safety
If the triac for the motor is in short-circuit, or if the tachometer generator is interrupted, 4 trials are
executed in intervals of 5 minute each.
After a break of 20 minutes, the fifth and last trial is started. If the motor does not run this time, the
programme is aborted.
(see Page Service-Program fault display E60)
DGS-TDS-N 12.06 R.B.
© Electrolux
- 29 -
599 52 74 52
EN
Motor, Motor control board
Electronic EWM2500
These appliances include a 2-pin asynchronous three-phase motor. This motor is directly driven by a
special inverter motor electronic system. This changes the frequencies of the rotary current in
accordance with the required rotational speed. The motor electronic system is connected with the control
electronic system via a control line.
Connection:
The ohmic resistance of the tacho generator
amounts to approx. 119 Ohms. The measurable
resistance of the motor coils can be measured
between the connection contacts of motors
m4-m5 / m4-m6 / m5-m6 and amount to
approx. 5.5 Ohms in each case. The phase shift
between the phases is 120° and peak amplitude
is 310V.
Safety
If the transistor for the motor is in short-circuit, or if the tachometer generator is interrupted, 4 trials
are executed in intervals of 5 minute each.
After a break of 20 minutes, the fifth and last trial is started. If the motor does not run this time, the
programme is aborted.
(see Page Service-Program fault display E50)
DGS-TDS-N 12.06 R.B.
© Electrolux
- 30 -
599 52 74 52
EN
Drum movements
Sek.
D55
1/Min.
12
4
12
4
0
55
0
-55
N 55
Sek.
1/Min.
8
8
8
8
0
55
0
-55
E 55
Sek.
1/Min.
3
10
3
10
0
55
0
-55
E 55
Sek.
1/Min.
3
10
3
10
0
50
0
-50
PWL_1
Sek.
1/Min.
40
1
40
1
0
35
0
-35
PWL_4
Sek.
1/Min.
57
1
57
1
DGS-TDS-N 12.06 R.B.
0
35
0
-35
© Electrolux
- 31 -
599 52 74 52
EN
Spin profiles
C0
1/Min.
FUCS
300
FUCS
450
FUCS
450
650
Sek.
x
0
x
0
x
5
0
AS
nein
nein
nein
nein
nein
nein
nein
C1
1/Min.
FUCS
FUCS imp
FUCS
450
650
850
850
Sek.
x
x
x
30
15
10
60
AS
nein
nein
nein
AS
AS
AS
nein
C2
1/Min.
FUCS
FUCS imp
FUCS
450
650
850
1000
Sek.
x
x
x
30
20
10
60
AS
nein
nein
nein
AS
AS
AS
nein
COT_CF
1/Min.
FUCS
FUCS imp
FUCS
450
650
850
1000
1150
1400
Sek.
x
x
x
30
15
5
95
75
110
AS
nein
nein
nein
AS
AS
AS
nein
nein
nein
SYN_CF
1/Min.
FUCS
FUCS imp
FUCS
450
650
900
Sek.
x
x
x
5
10
55
DGS-TDS-N 12.06 R.B.
AS
nein
nein
nein
nein
nein
nein
© Electrolux
- 32 -
599 52 74 52
EN
Spin profiles
CF (Feinwäsche)
1/Min.
FUCS
FUCS imp
FUCS
450
700
900
Sek.
x
x
x
35
5
20
AS
nein
nein
nein
AS
AS
AS
CF (Wolle)
1/Min.
FUCS
FUCS imp
FUCS
450
650
850
1000
Sek.
x
x
x
5
1
1
20
AS
nein
nein
nein
AS
AS
AS
nein
Separater Schleudergang
1/Min.
FUCS
FUCS imp
FUCS
450
650
850
1000
1150
1400
Sek.
x
x
x
10
10
10
10
10
20
AS
nein
nein
nein
AS
AS
AS
nein
nein
nein
EASY_IRON_IMP
1/Min.
FUCS
450
FUCS
650
FUCS
800
FUCS
900
Sek.
x
0
x
0
x
0
x
0
AS
nein
nein
nein
AS
nein
AS
nein
AS
CSR
1/Min.
FUCS
FUCS imp
FUCS
450
AS
Sek.
x
x
x
120
AS
nein
nein
nein
AS
indicates that the anti-foam function is active.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 33 -
599 52 74 52
EN
Function of the FUCS
“FUCS” is an English expression and means “Fast Unbalanced Control System”
Function:
The unbalance control includes 4 phases. These phases are of different duration and have different limits
of unbalance. The magnitude of the unbalance is calculated every 300 ms, hereby the magnitude is
compared to the fixed unbalance limits, and then it is decided whether the speed will be increased or
reduced by 2 1/min. FUCS starts at 55 1/min and ends ideally when reaching 115 1/min.
Phase 0:
When the unbalance threshold (850gr.) of the first phase is reached, the appliance performs
a spin cycle with 100 1/min for 5 sec followed by a spin cycle pulse of 470 1/min.
Phase 1:
The first phase (350gr.) takes max. 120 sec to obtain the required speed of 115 1/min. If the
speed is not reached after this 120 sec, the spinning cycle will be stopped. The laundry is
dispersed and it is changed to phase 2.
Phase 2:
Phase 2 (650gr.) takes max. 60 sec. Here it is tried to obtain the speed of 115 1/min with
various unbalance limits. If the speed is not reached after 60 sec, the spinning cycle will be
stopped again. The laundry is dispersed and it is changed to phase 3.
Phase 3:
In phase 3 (1100gr.), the required speed is reduced to 85 1/min. Within 90 sec, speed should
be reached, the machine then runs a spin-dry cycle at 100 1/min for 5 sec.and a subsequent
spin-dry pulse at 470 1/min, then again starting by phase 1. If the speed is reached, a
reduced spin-dry cycle at 650 1/min is carried out. If the speed is not reached, spin-dry is
skipped.
1/min
Perfect balance
-
Reversing
FUCS phase 0
with spin-dry pulse
Reversing
FUCS phase 1
regular spin-dry
DGS-TDS-N 12.06 R.B.
© Electrolux
- 34 -
599 52 74 52
EN
Balancing after two attempts
-
Low speed
FUCS phase 0
FUCS phase 1
FUCS phase 2
Balancing after the third phase (normal spin-speed)
-
FUCS phase 0
with spin pulse
FUCS phase 1
FUCS phase 2
FUCS phase 3
with spin pulse
FUCS phase 1
FUCS phase 2
FUCS phase 3
Normal spin
Balancing after the third phase (reduced spin-speed)
-
FUCS phase 0
FUCS phase 1
FUCS phase 2
FUCS phase 3
with spin pulse
FUCS phase 1
FUCS phase 2
FUCS phase 3
reduced-speed spin
Unalancing after the third phase
-
FUCS phase 0
FUCS phase 1
FUCS phase 2
FUCS phase 3
FUCS phase 1
FUCS phase 2
FUCS phase 3
no spin
DGS-TDS-N 12.06 R.B.
© Electrolux
- 35 -
599 52 74 52
EN
Foam Detection
Anti-foam control is excited via analog pressure switch.
Spin-dry phase without foam:
Spin-dry phase with little foam:
Spin-dry
Anti-Foam
Pulse with
450 1/Min
Spin-dry
Pulse with
450 1/Min
FUCS
FUCS
Spin-dry with little foam:
When the analogous pressure switch detects foam (45 mm “full”), the spinning cycle is stopped
and the drain pump keeps on running until the foam level will be fallen below (15 mm “empty”) and
the spinning cycle is continued.
Spin-dry with excess foam:
When the analogous pressure switch detects a foam 5 times (45 mm “full”), the spinning will be
skipped. Draining is carried out for 1 minute with the motor at stop. If too much foam is detected
during any wash cycle, an additional rinse cycle is added.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 36 -
599 52 74 52
EN
Service Program
Fault indication by multifunctionsdisplay LCD
Switch off the appliance.
Hold buttons 6 and 5 pressed simultaneously and turn the program selector one position to
the right.
Hold the two selected buttons pressed until possibly a buzzer will sound and/or the LCD will
give a light.
By the program selector it is possible to interrogate the desired checking function according
to the table.
1
Position of the
rotary switch
Off
21 - 15
Positions
01
02
03
04
05
06
07
08
09
10
DGS-TDS-N 12.06 R.B.
© Electrolux
Button
2
3
4
5
6
Test function
Off
Button 6 1) Start of the customer service testprogram
and
2) LCD - Test
Button 5 LEDs are step by step illuminated.
If you press a button the according LED is on.
Water channel mainwash
Water intake up to savety level fS
Time max. 5 min
Valve mainwash
Display indicates current water level in mm
Water channel prewash
Water intake up to savety level fS
Time max. 5 min
Valve prewash
Display indicates current water level in mm
Water channel softener
Water intake up to savety level fS
Time max. 5 min
Valve mainwash and prewash
Display indicates current water level in mm
Water channel spots
Water intake up to savety level fS
Time max. 5 min
Valve spots or hotwater
Display indicates current water level in mm
Heating and circulation pump
Heating up to 90°C
Time max. 10 min
Water intake over mainwash chamber
Display indicates current temperature in °C
Tub leakage test
Water intake over mainwash chamber up to 1. Niv.
Motor rotation 250 1/min
Display indicates current speed in 1/min
Draining and spinning
Draining
Spinning up to maximium spin speed,
if level < fSch
Display indicates current speed in 1/min
DSP
The drum is positioned if level < fSch
Displaying the error code (programme display)
- 37 -
599 52 74 52
EN
DGS-TDS-N 12.06 R.B.
© Electrolux
Cable defect
- 38 Replace inlet valve
Replace pressure sw itch
Check the hose for the pressure sw itch
Inlet valve defect
Pressure sw itch defect
Hose for pressure sw itch leakage or blocked
Pressure sensor defect
Cable interrupted
Frequency of the pressure sensor out of limit
Pressure sensor defect
599 52 74 52
Clean filter
in betw een 0 - 66mm and antiboil level off
Replace air trap, Replace pressure sensor
Replace inlet valve
Open tap
Replace cable
Replace pressure sensor
After initial calibration the w aterlevel not
E32 Calibration problems pressure sensor
E30 E31
E24 Drain pump triac sensing failure 1 Input voltage allw ays 0V or 5V Replace electronic
Cable drainpump
Replace drainpump,
Replace electronic
Replace pressure sw itch
Replace pressure sensor
Pressure sw itch defect
Electronic defect
Replace drainpump
Check draining system
Reduced pump output rate
Remove foreign object
Pump interrupted
Pump blocked / not w orking
No draining
Clean filter
Valve flow rate to low
E23 Incongruence betw een drainpump and electronic
E20 E21
Check the drain pipe position
Wrong drain pipe position
Replace electronic
Replace air trap
Cable pressure sw itch and electronic
Air trap system leaking
Electronic defect
Open tap
Change the valve
Clean filter
Remedy
Valve does not open / interruption
Valve flow rate to low
Type of fault
Water tap closed
No w ater filling
E13 Not enough w ater
E10 E11
Fault
code
0
1
2
2
0
1
1
S X
A X
A
A
S X
S
S X
X
X
X
X
X
E E W
W W 1
M M D
2 1 0
0 0 0
Alarm 0 0 1
Code 0 0 0
9
W
1
D
0
0
2
0
0
X
X
X
X
X
E
W
M
1
0
0
0
E E E E
W W W N
M M M V
2 2 3 0
0 0 0 6
0 0 0
0 0 0
E N N
V E E
O W W
X X X X
X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X X X X X
E
W
M
1
0
0
0
p
l
u
s
Service Program
Fault indication by multifunctionsdisplay LCD
EN
DGS-TDS-N 12.06 R.B.
Type of fault
© Electrolux
Cable pressure sw itch and electronic
Fault has to be for a time longer than 3 sec.
Replace air trap
- 39 -
No pressure differences detected
Airtrap blocked
599 52 74 52
Replace electronic
Replace doorlock
Door is not unlocking at the end of cycle Tout 4 min
Replace electronic
Electronic defect
E42 Door lock defect
Replace cable
Replace cable
Cable defect
Door is unlocked during the cycle Tout 15 sec
Replace doorlock
Lid open
Door lock defect
E40 E41
Replace electronic
Replace electronic
Clean airtrap
Change airtrap
Pressure sw itch Niv.1 sensing failure Inputvolt. allw ays 0V or 5V Replace electronic
Replace electronic
Replace electronic
Antiboil 2 sensing failure 1 Input voltage allw ays 0V or 5V
Cable pressure sw itch and electronic
Replace pressure sw itch
Air trap system leaking
Replace inlet valve, Replace electronic
Replace air trap
Replace cable
Antiboil 1 sensing failure 1 Input voltage allw ays 0V
E39 sensing failure Inputvolt. allw ays 0V
E3A Heating element relay defect
E36
E37
E37
E38
E35 Safety pressure sw itch on for a time longer than 15 sec.
Drain pump w ill be activated until level is below 120 mm
Level has to be 300mm for a time of more than 15 sec
Replace pressure sensor
Fault has to be for a time longer than 60 sec.
E35 Safety level (Pressure sensor)
Replace cable
and antiboil level 2
Replace pressure sensor
Replace heating element
E34 Incongruence betw een pressure sensor
1
0
0
1
1
1
1
1
1
2
1
1
Replace pressure sw itch, Replace electronic 1
Replace cable
Replace air trap
Replace pressure sensor
Remedy
and antiboil level 1
E33 Incongruence betw een pressure sw itch Niv.1
and antiboil level 1
Fault has to be for a time longer than 60 sec.
E33 Incongruence betw een pressure sensor
Fault
code
S X
S X
A
A
A X
A X
A
A X
A
A X
A X
A
A X
X
X
X
X
X
X
X
E E W
W W 1
M M D
2 1 0
0 0 0
Alarm 0 0 1
Code 0 0 0
9
W
1
D
0
0
2
0
0
X
X
X
X
X
X
X
E
W
M
1
0
0
0
X X X
X X X
X X X
X X X X X
X X X X X
X X X X
X X X X
X
E E E E
W W W N
M M M V
2 2 3 0
0 0 0 6
0 0 0
0 0 0
E N N
V E E
O W W
X X X X
X X X
X
X X X
X
X
E
W
M
1
0
0
0
p
l
u
s
Service Program
Fault indication by multifunktionsdisplay LCD
EN
DGS-TDS-N 12.06 R.B.
Type of fault
© Electrolux
- 40 Replace electronic
Replace motor, Replace cable
Replace tachognerator
Replace motor, replace cable
Motor relay defect
Motor circuit interrupted
No signal from tachogenerator, No signal after 15 min
Inverter current goes above threshold (>15A)
DC bus voltage goes above threshold (>430V)
than 2 seconds
599 52 74 52
parameters due to repetitive reset
E5F FCV control board is continuously asking for configuration
control board and mainboard
Replace electronic
Replace motor control board, replace cable
Replace electronic
Replace cable
Replace motor control board
DC bus voltage goes below threshold (<175V)
FCV cannot receive and/or transmit a message for more
Replace motor control board
Replace motor control board, replace cable
Heat Sink temperature goes above threshold (88°C)
E5E There are communication problems in betw een FCV
E5A
E5B
E5C
E5D
Replace motor control board, replace cable
Replace motor, replace tachogenerator
different from zero
E59 No tacho signal for 3 seconds after new speed target
Replace motor control board
Replace motor, replace cable
Replace motor control board
Replace electronic
Motor triac sensing failure Input voltage allw ays 0V or 5V
Replace electronic
Replace cable
Motor cable defective
E58 Motor phase current goes above threshold (>4,5A)
E53
E54
E55
E56
E57
Replace motor
Motor blocked
Replace tachognerator
Replace cable
Replace electronic
Motor cable short circuit
Replace electronic
Replace electronic
Replace electronic
Replace doorlock, Replace cable
Remedy
Motortriac short circuit
E52 No signal from tachogenerator
E50 E51
E44 Door lock sensing failure Inputvoltage allw ays 0V or 5V
E45 Door lock triac sensing failure Inputvoltage allw ays 0V or 5V
E43 Door lock triac defect
Fault
code
A X
A X
A X
A
A
A
A
A
1
1
1,6
1,6
1,6
1,6
A
A
A
A
A
A
1,6 A
1,6 A
1
1,6
1
1
1,6
X
X
X
X
1,6 A X
1,6 A X
1
1
0
X
X
X
X
X
X
X
E E W
W W 1
M M D
2 1 0
0 0 0
Alarm 0 0 1
Code 0 0 0
9
W
1
D
0
0
2
0
0
X
X
X
X
X
X
X
E
W
M
1
0
0
0
E E E E
W W W N
M M M V
2 2 3 0
0 0 0 6
0 0 0
0 0 0
E N N
V E E
O W W
X
X X X
X X X
X
X
X
X
X X
X X
X
X
X
X
X X
X X
X X
X
X
X X X X X
X X X
X X X X X
X X X X X
X X X X X
E
W
M
1
0
0
0
p
l
u
s
Service Program
Fault indication by multifunctionsdisplay LCD
EN
DGS-TDS-N 12.06 R.B.
© Electrolux
- 41 -
Connection heating element interrupted
Replace heating element
Replace cable
NTC defective
Cable defective
Incongruence betw een antiboil 2 and relay
E93 Configuration error
E94 Lost of cycle datas
599 52 74 52
EN
Replace electronic
Wrong configuration of the machine
Wrong configuration of the machine
w ith electronic
In/Output electronic is incompatible
Replace cable, Replace electronic
Replace In/Output electronic
betw een In/Output electronic and mainelectronic
Replace electronic
Replace recirculation pump
Replace electronic
Replace electronic
Wrong configuration of the machine
Replace electronic
Check the position
Replace cable
Replace NTC, Replace electronic
or replace other components
Replace heating element
Replace cable
Replace electronic
Replace pressure sw itch antboil 1
Replace cable
Interrupted communication
E92 Incongruence betw een In/Output electronic and electronic
E90 E91
Triac defective
E84 Recirc. pump sensoring failure Input voltage allw ays 0V or 5V
E85 Recirculation pump defect
E83 Wrong selector reading
Wrong selector reset postion detection
E74 NTC isn't in the correct position in the tub
NTC interruption
E71 NTC short circuit
E68 Leakage current in the appliance too high.
Incongruence betw een antiboil 1 and relay
E66 Heating element defect
Replace pressure sw itch antboil 2
Replace NTC
Temperature greater 88°C for a time longer than 5 min
E66 Heating element defect
E80 E82
E70
Replace cable
NTC defective
Heating element defect
Replace NTC
Replace heating element
Remedy
Maximum heating time expired
Type of fault
Insufficient heating
E62 Overheating:
E60 E61
Fault
code
1
1
1
0
1
2
4
3
3
7
2
2
2
3
A X
A X
A X
A X
A X
A X
A
S
S
S X
A
A
A X
A X
S X
X
X
X
X
X
X
X
X
E E W
W W 1
M M D
2 1 0
0 0 0
Alarm 0 0 1
Code 0 0 0
9
W
1
D
0
0
2
0
0
X
X
X
X
X
X
X
X
E
W
M
1
0
0
0
E E E E
W W W N
M M M V
2 2 3 0
0 0 0 6
0 0 0
0 0 0
E N N
V E E
O W W
X X X X X
X X X X X
X X X X X
X X X X X
X X X X
X X X X
X X X X X
X X X X X
X X X X X
X X X X X
X
X X X X X
X X X X X
X X X X X
E
W
M
1
0
0
0
p
l
u
s
Service Program
Fault indication by multifunctionsdisplay LCD
Type of fault
DGS-TDS-N 12.06 R.B.
© Electrolux
DSP defect
- 42 -
Pow er supply frequency out of limits
EBE Line Safe relay faulty
EBF Line Safe "sensing" faulty
EB3 Pow er supply voltage too low
EB2 Pow er supply voltage too high
EB0 EB1
EA6 Drum have blocked in the first ca. 3sec.
EA5 Triac for DPS defect
EA6 Drum have blocked in the first ca. 30sec.
EA4 DPS defect
EA2 DPS sensing defect
EA3 DPS unable to lock motor pully
EA0 EA1
E9A Firmw are betw een loudspeaker and In/Output electronic not ok
E99 Connection betw een loudspeaker and In/Output electronic
motor control board and electronic
E98 Incongruence betw een
E97 Incongruence betw een selector and cycles configuration
cycles configuration
E95 Communication error betw een microprocessor and EEPROM
E96 Incongruence betw een Hardw are-version and
Fault
code
599 52 74 52
Replace electronic
Replace electronic
Replace electronic
Wrong or disturbed pow er supply line
Replace electronic
Wrong or disturbed pow er supply line
Replace electronic
Wrong or disturbed pow er supply line
Drum lid not closed
Cut drive belt, Replace DSP
Drum lid not closed
Cut drive belt, Replace DSP
Replace electronic
Replace w iring
Replace electronic
Replace DPS
Replace w iring, Cut drive belt
Replace DSP, Replace electronic
Replace electronic
Replace w iring, Cut drive belt
Replace DSP, Replace electronic
Replace In/Output electronic
Replace w iring
Replace loudspeaker
Replace w iring
Replace electronic
Replace electronic
Wrong configuration of the machine
Replace electronic
Wrong configuration of the machine
Replace electronic
Remedy
2
2
0
0
0
0
0
5
0
0
0
0
0
0
A
A
A
A
A
A
A
X
X
X
X
S X
A
A
A
A
A
A
X
X
X
X
X
X
X
E E W
W W 1
M M D
2 1 0
0 0 0
Alarm 0 0 1
Code 0 0 0
9
W
1
D
0
0
2
0
0
X
X
X
X
X
X
X
X
E
W
M
1
0
0
0
E E E E
W W W N
M M M V
2 2 3 0
0 0 0 6
0 0 0
0 0 0
E N N
V E E
O W W
X
X
X X X X
X X X X
X X X X
X X X X
X
X X X X X
X X
X X
X
X X X X X
X X X X X
E
W
M
1
0
0
0
p
l
u
s
Service Program
Fault indication by multifunctionsdisplay LCD
EN
DGS-TDS-N 12.06 R.B.
© Electrolux
Inlet valve blocked
Type of fault
Time for draining to long
- 43 -
Pow er supply frequency out of limits
EHE Line Safe relay faulty
EHF Line Safe "sensing" faulty
EH3 Pow er supply voltage too low
EH2 Pow er supply voltage too high
EH0 EH1
Unbalance to high, unbalance >1200gr
EF5 Interrupted the spinning phase
EF4 No signal from flow meter w ith electro valves sw itched on
Drain pump interruption
Drain pump cable defective
EF3 Aqua Control system activated
Replace electronic
Replace electronic
Replace electronic
Wrong or disturbed pow er supply line
Replace electronic
Wrong or disturbed pow er supply line
Replace electronic
Wrong or disturbed pow er supply line
check stationary behaviour of w asher
Pay attention to the quantity of laundry,
insufficient.
Water tap closed or mains pressure
Replace drain pump
Replace cable
Leakage in the machine
Not overdosing
Filter dirty
Drainhose closed
Checking drainpump
To much foam during the drain phase
Cleaning drainhose and filter
Cleaning drainhose and filter
Checking drainpump
Drainhose closed
Replace turbidity sensor
Replace w iring
Replace inlet valve, Replace electronic
Remedy
Filter dirty
EF2 Detergent overdosing
EF0 EF1
EC2 Turbidity sensor defect
EC0 EC1
Fault
code
2
2
0
0
0
0
0
2
6
2
A
A
A
A
A
A X
A X
S X
A
E E W
W W 1
M M D
2 1 0
0 0 0
Alarm 0 0 1
Code 0 0 0
9
E
W
M
1
0
0
0
W
1
D
0
0
2
0
0
X
X
X
E E E E
W W W N
M M M V
2 2 3 0
0 0 0 6
0 0 0
0 0 0
E N N
V E E
O W W
X
X
X
X
X
X
X
X X
X X X X X
X X X X X
X X X X X
E
W
M
1
0
0
0
p
l
u
s
Service Program
Fault indication by multifunctionsdisplay LCD
599 52 74 52
EN
Service Program
Fault indication by multifunctionsdisplay LCD
0
1
2
3
4
5
6
DGS-TDS-N 12.06 R.B.
Composition alarm codes
Reactivate
the machine
Alarm state
with
Program cycle interrupted
Start Button
S
Program cycle interrupted
Off / On
A
Door locked
Program cycle stopped
Drain pump is activatedt
Heating step is skipped
Program canceled
DSP-function is skipped
after 5 attempt
© Electrolux
- 44 -
599 52 74 52
EN
Service Program
Rapid reading of alarm codes
The last alarm code can be displayed even if the programme selector is not in the 10th position
(service test mode) or if the appliance is in normal operating mode (e.g. during the execution of an
washing programme):
-
Keep buttons 6 and 5 pressed in together.
-
The alarm sequence continues as long as the two buttons are held down
-
While the alarms are displayed, the appliance continues to perform the cycle or, if in the
programme selection phase, maintains the previously-selected options in memory.
Indication of error code through LEDs
The error code is additionally indicated by the START/PAUSE LED.
The START/PAUSE LED is a double LED with colors red and green.
When the red LED is flashing (0.5 sec on, 0.5 sec off), the alarm family will be indicated, when the green
LED is flashing afterwards, the alarm number will be indicated.
e.g.
EA4
-
EA4
-
pause of 1.5 sec
-
EA4
-
pause of 2.5 sec, then repetition
Alarm codes flashing
1
1x
:
:
9
9x
A
10 x
B
11 x
:
:
H
17 x
---> red LED flashes 10 x
---> green LED flashes 4 x
Cancelling the last alarm
-
Enter service test program (page 37)
-
Press buttons 6 and 5 in together and keep them pressed in until the LCD E00.
It is good practice to cancel the last alarm:
-
after reading the alarm code, to check whether the alarm re-occurs during diagnostics
-
after repairing the appliance, to check whether it re-occurs during testing.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 45 -
599 52 74 52
EN
Demo-Programm
Activate the demo - program
1
2
3
4
5
6
These appliances have a Demo-Mode for demonstration purposes.
main electronic EWM2100
main electronic EWM2500
Software
Software
WBD101..
WCB101..
1.
Access to demo program
Switch off the appliance.
Keep buttons 6 and 5 pressed in together and rotate the programme selector three
positions to the right.
Keep both selected keys pressed for about 2 seconds.
You can select the individual programs and the associated option keys by using the
program selector switch.
The key start/pause is disabled.
The demo program will remain in the memory even if the appliance is switched Off.
2.
Adandoning the demo program
Switch off the appliance.
Keep buttons 6 and 5 pressed in together and rotate the programme selector three
positions to the right.
Keep both selected keys pressed for about 2 seconds.
Switch Off the appliance to deactivate the demo program.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 46 -
599 52 74 52
EN
Electronic-Test
Activate the electronic-test
1
1.
3
4
5
6
Access to the electronic-test
-
2.
2
Switch off the appliance.
Hold buttons 6 and 5 pressed simultaneously and turn the program selector one
position to the right.
Keep both selected keys pressed for about 2 seconds.
Hold buttons 6 and 5 together and pressed again.
Switch off and on the appliance
The display indicates „ELE“
The electronic-test it running
- Filling till 1. Niveau
- Movement with 50 1/min.
- Heating up to max. 50°C or 20min duration.
Adandoning the elektronik-test
-
Switch off the appliance.
DGS-TDS-N 12.06 R.B.
© Electrolux
- 47 -
599 52 74 52
EN
Operating time
Activate the operating time
1
2
3
4
5
6
1.
Access to the operating time
Switch off the appliance.
Keep buttons 6 and 5 pressed in together and rotate the programme selector five
positions to the right.
Keep both selected keys pressed for about 2 seconds.
2.
Adandoning the operating time
Switch off the applinace.
e.t. 3364 operating time
1. display
after 2 sec.
2. display
TC3 low
TC3 high
TC2
DGS-TDS-N 12.06 R.B.
© Electrolux
- 48 -
599 52 74 52
EN
Circuit Diagram
Technicl Specifications
GENERAL FEATURES
WATERSAFETY SYSTEM :
Type ................................................................. 110539000
Supply voltage ....................................................... 230 V
Dimensions (height, width, depth) ............... 85/40/60 cm
Dryclothes loading capacity .................................. 5,5 kg
Drum rotation speed (washing/spinning)55/600-1500 r.p.m
Intermediate speed ......................................... 1000 r.p.m
Intermediate speed ........................................... 850 r.p.m
WATER LOAD CAPACITY (without clothes) :
Heating Level I ............................................................. 2 l
Heating Level II ............................................................2 l
Anti-overflow level ...................................................... 43 l
WATER PRESSURE :
Max./Min. .................................................. 0,8/0,05 MPa
CONSUMPTIONS (COTTON 60°) :
see energie label
TEMPERATURE PROBE (NTC) ................ 6 kohm at 20°C
PRESSURE SWITCH ANALOGIC :
Analogic Level ....................................... 000 mm - 44,7 Hz
Analogic Level ....................................... 300 mm - 36,1 Hz
USER INTERFACE : EWM2100
Indentification mark ............................................ 13251510.
Indentification mark ............................................ 13251511.
Indentification mark ............................................ 13251512.
Indentification mark ............................................ 13251513.
USER INTERFACE : EWM2500
Indentification mark ............................................ 13251520.
Indentification mark ............................................ 13251521.
Indentification mark ............................................ 13251522.
Indentification mark ............................................ 13251523.
TECHNICAL PARTICULARS
DRAIN PUMP :
Maxi head ........................................................... 100 cm
Mini head .............................................................. 70 cm
Delivery rate ...................................................... 25 l/min
Power absorbed ..................................................... 30 W
Winding resistance .................................... 164/224 ohm
HEATING ELEMENT :
Power absorbed ................................................. 1950 W
Resistance .......................................................... 27 ohm
WATER VALVE :
Delivery rate ...................................................... 5,5 l/min
Coil resistance ................................................ 4300 ohm
CYCLING PUMP :
Delivery rate ...................................................... 12 l/min
Power absorbed ..................................................... 18 W
Winding resistance ........................................... 200 ohm
MODULE REGULATION SPEED : EWM2500
Module ................................................................ 13252771.
Supply voltage ............................................................ 230 V
DOOR POSITIONNING (electric):
Indentification mark ......................................... 146132000
DISPLAY LCD :
TC4 ................................................................... 13252920.
TC3 ................................................................... 13252911.
TC2 ................................................................... 13252901.
TC1 ................................................................... 13252950.
TC1 ................................................................... 13252830.
CONNECTION :
Water supply connection ................................... 1,5 m long
Water discharge connection height ........ mini 70 / maxi 100 cm
Total power ........................................................... 2300 W
DOOR INTERLOCK :
Type .................................................................voltmetric
Internal door locking .............................................. 0,02 s
Internal door release .............................................. 0,02 s
DOOR INTERLOCK :
Type .................................................................voltmetric
Internal door locking .................................................. 6 s
Internal door release .......................................... 40-120 s
DGS-TDS-N 12.06 R.B.
© Electrolux
- 49 -
599 52 74 52
EN
COLLECTOR MOTOR :
Pulley ratio .................................................................. 10,2
Insulation class ............................................................... F
Spinning speed ................................................. 1450 r.p.m
Winding resistance (1-2) ..................................... 5,44 ohm
Winding resistance (3-2) ..................................... 5,44 ohm
Winding resistance (1-3) ..................................... 5,44 ohm
TACHOGENERATOR :
Resistance (5-4) ................................................... 115 ohm
Pulley ratio .................................................................. 10,4
Insulation class ............................................................ B/F
Spinning speed ................................................. 1450 r.p.m
Winding resistance (3-4) ..................................... 2,20 ohm
Winding resistance (1-2-5) .................................. 0,55 ohm
Winding resistance (2-5) ..................................... 1,10 ohm
TACHOGENERATOR :
Resistance (6-7) ................................................... 135 ohm
Pulley ratio .................................................................. 10,4
Insulation class ............................................................ B/F
Spinning speed ................................................. 1450 r.p.m
Winding resistance (3-4) ..................................... 1,78 ohm
Winding resistance (1-2-5) .................................. 0,60 ohm
Winding resistance (2-5) ..................................... 1,75 ohm
TACHOGENERATOR :
Resistance (6-7) .................................................. 68,7 ohm
Pulley ratio .....................................................................12
Insulation class ............................................................ B/F
Spinning speed ................................................. 1250 r.p.m
Winding resistance (3-4) ..................................... 1,73 ohm
Winding resistance (1-2-5) .................................. 1,10 ohm
Winding resistance (2-5) ..................................... 1,70 ohm
TACHOGENERATOR :
Resistance (6-7) .................................................. 15,1 ohm
Pulley ratio .....................................................................12
Insulation class ............................................................ B/F
Spinning speed ................................................. 1250 r.p.m
Winding resistance (3-4) ..................................... 1,65 ohm
Winding resistance (1-2-5) .................................. 0,62 ohm
Winding resistance (2-5) ..................................... 1,23 ohm
TACHOGENERATOR :
Resistance (6-7) ................................................... 135 ohm
Pulley ratio .....................................................................12
Insulation class ............................................................ B/F
Spinning speed ................................................. 1150 r.p.m
Winding resistance (3-4) ..................................... 1,90 ohm
Winding resistance (2-5) ..................................... 1,30 ohm
TACHOGENERATOR :
Resistance (6-7) .................................................. 68,7 ohm
DGS-TDS-N 12.06 R.B.
© Electrolux
Pulley ratio .....................................................................14
Insulation class ............................................................ B/F
Spinning speed ................................................. 1050 r.p.m
Winding resistance (3-4) ..................................... 1,62 ohm
Winding resistance (2-5) ..................................... 1,67 ohm
TACHOGENERATOR :
Resistance (6-7) .................................................. 15,1 ohm
Pulley ratio .....................................................................14
Insulation class ............................................................ B/F
Spinning speed ................................................. 1050 r.p.m
Winding resistance (3-4) ..................................... 2,46 ohm
Winding resistance (2-5) ..................................... 1,86 ohm
TACHOGENERATOR :
Resistance (6-7) .................................................. 68,7 ohm
Pulley ratio .....................................................................18
Insulation class ............................................................ B/F
Spinning speed ................................................... 850 r.p.m
Winding resistance (3-4) ..................................... 1,62 ohm
Winding resistance (2-5) ..................................... 1,67 ohm
TACHOGENERATOR :
Resistance (6-7) .................................................. 15,1 ohm
Pulley ratio .....................................................................18
Insulation class ............................................................ B/F
Spinning speed ................................................... 850 r.p.m
Winding resistance (3-4) ..................................... 2,25 ohm
Winding resistance (2-5) ..................................... 1,83 ohm
TACHOGENERATOR :
Resistance (6-7) .................................................. 68,7 ohm
Pulley ratio .....................................................................21
Insulation class ............................................................ B/F
Spinning speed ................................................... 600 r.p.m
Winding resistance (3-4) ..................................... 3,82 ohm
Winding resistance (2-5) ..................................... 3,58 ohm
TACHOGENERATOR :
Resistance (6-7) .................................................. 68,7 ohm
ASYNCHRONOUS THREE-PHASE MOTOR :
Pulley ratio .....................................................................12
Insulation class ............................................................... F
Spinning speed ............................................... 17000 r.p.m
Winding resistance X (4-5) .................................... 5,5 ohm
Winding resistance Z (4-6) .................................... 5,5 ohm
Winding resistance Y (5-6) .................................... 5,5 ohm
TACHOGENERATOR :
Resistance (7-8) .................................................... 119ohm
- 50 -
599 52 74 52
EN
Circuit Diagram
Wiring Diagram
DGS-TDS-N 12.06 R.B.
© Electrolux
- 51 -
599 52 74 52
EN
Circuit Diagram
Elementary Diagram
DGS-TDS-N 12.06 R.B.
© Electrolux
- 52 -
599 52 74 52
EN
Program cycles
Cotton / Coloured 60° ECO (without options)
Software WBD101..
1400
1200
1000
800
600
400
200
0
1
397 793 1189 1585 1981 2377 2773 3169 3565 3961 4357 4753 5149 5545 5941 6337 6733 7129 7525 7921 8317 8713 9109
drum_speed
drum_speed
60
50
40
30
20
10
9079
8812
8545
8278
8011
7744
7477
7210
6943
6676
6409
6142
5875
5608
5341
5074
4807
4540
4273
4006
3739
3472
3205
2938
2671
2404
2137
1870
1603
1336
802
1069
535
1
268
0
wash_temp
DGS-TDS-N 12.06 R.B.
© Electrolux
- 53 -
599 52 74 52
EN
DGS-TDS-N 12.06 R.B.
© Electrolux
- 54 -
10
0
4902
4733
4564
4395
4226
4057
3888
3719
3550
3381
3212
3043
2874
2705
2536
2367
2198
2029
599 52 74 52
5747
5578
20
5645
30
5409
40
5479
50
5240
60
5313
70
5071
drum_speed
vitesse réel
5147
4981
4815
4649
4483
4317
4151
3985
3819
3653
3487
3321
3155
2989
2823
2657
2491
2325
2159
1860
1691
1522
1353
1184
1015
846
677
508
339
170
1
Cotton 60° (without options)
1993
1827
1661
1495
1329
1163
997
831
665
499
333
167
1
Program cycles
Software WBD101..
1400
1200
1000
800
600
400
200
0
Watch
temp
wash_temp
EN
DGS-TDS-N 12.06 R.B.
© Electrolux
- 55 -
50
40
30
20
10
0
599 52 74 52
7041
6821
6601
6381
6161
5941
5721
5501
5281
5061
4841
4621
4401
4181
3961
3741
3521
3301
3081
2861
2641
2421
2201
1981
1761
1541
1321
1101
881
661
441
7481
60
7491
70
7261
drum_speed
drum_speed
7277
7063
6849
6635
6421
6207
5993
5779
5565
5351
5137
4923
4709
4495
4281
4067
3853
3639
3425
3211
2997
2783
1
221
Cotton / Cloured 60° + Rinse+
2569
2355
2141
1927
1713
1499
1285
1071
857
643
429
215
1
Program cycles
Software WBD101..
1400
1200
1000
800
600
400
200
0
Watch
temp
wash_temp
EN
DGS-TDS-N 12.06 R.B.
© Electrolux
- 56 -
599 52 74 52
1:56:30
2:00:31
2:04:32
2:08:33
2:12:34
2:16:35
2:20:36
2:24:37
2:28:38
2:32:39
2:00:31
2:04:32
2:08:33
2:12:34
2:16:35
2:20:36
2:24:37
2:28:38
2:32:39
2:36:40
1:52:29
1:56:30
2:36:40
1:48:28
1:52:29
1:28:23
1:24:22
1:20:21
1:16:20
1:12:19
1:44:27
0
1:48:28
10
1:44:27
20
1:40:26
30
1:40:26
40
1:36:25
50
1:32:24
60
1:36:25
drum_speed
1:32:24
1:28:23
1:24:22
1:20:21
1:16:20
1:08:18
1:04:17
1:00:16
0:56:15
0:52:14
0:48:13
0:44:12
0:40:11
0:36:10
0:32:09
0:28:08
0:24:07
0:20:06
0:16:05
0:12:04
0:08:03
0:04:02
0:00:01
Cotton / coloured 60° ECO + Night cycle
1:12:19
1:08:18
1:04:17
1:00:16
0:56:15
0:52:14
0:48:13
0:44:12
0:40:11
0:36:10
0:32:09
0:28:08
0:24:07
0:20:06
0:16:05
0:12:04
0:08:03
0:04:02
0:00:01
Program cycles
Software WBD101..
70
60
50
40
30
20
10
0
wash_temp
EN
DGS-TDS-N 12.06 R.B.
© Electrolux
- 57 -
599 52 74 52
5441
5281
5121
4961
4801
4641
4481
4321
4161
4001
3841
3681
3521
3361
3201
3041
2881
2721
2561
2401
2241
2081
1921
1761
1601
1441
1281
1121
961
801
641
481
321
161
1
5577
5413
5249
5085
4921
4757
4593
4429
4265
4101
3937
3773
3609
3445
3281
3117
2953
2789
2625
2461
2297
2133
1969
1805
1641
1477
1313
1149
985
821
657
493
329
165
1
Program cycles
Synthetic 60° (without options) Software WBD101..
1400
1200
1000
800
600
400
200
0
drum_speed
drum_speed
70
60
50
40
30
20
10
0
Watch temp
wash_temp
EN
1
DGS-TDS-N 12.06 R.B.
© Electrolux
- 58 -
25
20
15
10
5
0
3691
3568
3445
3322
3199
3076
2953
2830
2707
2584
2461
2338
2215
2092
1969
1846
1723
1600
1477
1354
1231
1108
985
862
739
616
493
370
247
124
1
599 52 74 52
4183
4060
30
4081
35
3937
40
3961
45
3814
drum_speed
drum_speed
3841
3721
3601
3481
3361
3241
3121
3001
2881
2761
2641
2521
2401
2281
2161
2041
1921
1801
1681
1561
1441
1321
1201
1081
961
841
721
601
481
361
241
121
Program cycles
Delicates 40° (without options) Software WBD101..
1200
1000
800
600
400
200
0
Watchwash_temp
temp
EN
DGS-TDS-N 12.06 R.B.
© Electrolux
- 59 -
599 52 74 52
2721
2641
2561
2481
2401
2321
2241
2161
2081
2001
1921
1841
1761
1681
1601
1521
1441
1361
1281
1201
1121
1041
2789
2707
2625
2543
2461
2379
2297
2215
2133
2051
1969
1887
1805
1723
1641
1559
1477
1395
1313
1231
1149
1067
985
903
821
739
657
575
493
411
329
247
165
83
1
Wool 40° (without options)
961
881
801
721
641
561
481
401
321
241
161
81
1
Program cycles
Software WBD101..
1400
1200
1000
800
600
400
200
0
drum_speed
drum_speed
40
35
30
25
20
15
10
5
0
Watchwash_temp
temp
EN
Changes
Date
Page changed
07.11.2006
13, 27, 30, 36, 45
18.12.2006
13, 27
DGS-TDS-N 12.06 R.B.
© Electrolux
- 60 -
599 52 74 52
EN