Linksys WRP400 User guide

USER GUIDE
Cisco Small Business
WRP400 Wireless-G Broadband Router with 2 Phone
Ports
6bZg^XVh=ZVYfjVgiZgh
8^hXdHnhiZbh!>cX#
HVc?dhZ!86
6h^VEVX^[^X=ZVYfjVgiZgh
8^hXdHnhiZbhJH6EiZ#AiY#
H^c\VedgZ
:jgdeZ=ZVYfjVgiZgh
8^hXdHnhiZbh>ciZgcVi^dcVa7K
6bhiZgYVb!I]ZCZi]ZgaVcYh
8^hXd]VhbdgZi]Vc'%%d[[^XZhldgaYl^YZ#6YYgZhhZh!e]dcZcjbWZgh!VcY[VmcjbWZghVgZa^hiZYdci]Z8^hXdLZWh^iZVilll#X^hXd#Xdb$\d$d[[^XZh#
889:!88:CI!8^hXd:dh!8^hXdAjb^c!8^hXdCZmjh!8^hXdHiVY^jbK^h^dc!8^hXdIZaZEgZhZcXZ!8^hXdLZW:m!i]Z8^hXdad\d!98:!VcYLZaXdbZidi]Z=jbVcCZildg`VgZigVYZbVg`h08]Vc\^c\i]ZLVnLZLdg`!
6bZg^XVh=ZVYfjVgiZgh
6h^VEVX^[^X=ZVYfjVgiZgh
:jgdeZ=ZVYfjVgiZgh
A^kZ!EaVn!VcYAZVgcVcY8^hXdHidgZVgZhZgk^XZbVg`h0VcY6XXZhhGZ\^higVg!6^gdcZi!6hncXDH!7g^c\^c\i]ZBZZi^c\IdNdj!8ViVanhi!8896!889E!88>:!88>E!88C6!88CE!88HE!88KE!8^hXd!i]Z8^hXd8Zgi^[^ZY
8^hXdHnhiZbh!>cX#
8^hXdHnhiZbhJH6EiZ#AiY#
8^hXdHnhiZbh>ciZgcVi^dcVa7K
>ciZgcZildg`:meZgiad\d!8^hXd>DH!8^hXdEgZhh!8^hXdHnhiZbh!8^hXdHnhiZbh8Ve^iVa!i]Z8^hXdHnhiZbhad\d!8^hXdJc^in!8daaVWdgVi^dcL^i]djiA^b^iVi^dc!:i]Zg;Vhi!:i]ZgHl^iX]!:kZci8ZciZg!;VhiHiZe!;daadlBZ
HVc?dhZ!86
H^c\VedgZ
6bhiZgYVb!I]ZCZi]ZgaVcYh
6bZg^XVh=ZVYfjVgiZgh
6h^VEVX^[^X=ZVYfjVgiZgh
:jgdeZ=ZVYfjVgiZgh
7gdlh^c\!;dgbH]VgZ!<^\V9g^kZ!=dbZA^c`!>ciZgcZiFjdi^Zci!>DH!^E]dcZ!^Fj^X`HijYn!>gdcEdgi!i]Z>gdcEdgiad\d!A^\]iHigZVb!A^c`hnh!BZY^VIdcZ!BZZi^c\EaVXZ!BZZi^c\EaVXZ8]^bZHdjcY!B<M!CZildg`Zgh!CZildg`^c\
8^hXdHnhiZbh!>cX#
8^hXdHnhiZbhJH6EiZ#AiY#
8^hXdHnhiZbh>ciZgcVi^dcVa7K
6XVYZbn!CZildg`GZ\^higVg!E8Cdl!E>M!EdlZgEVcZah!Egd8dccZXi!HXg^eiH]VgZ!HZcYZg7VhZ!HB6GIcZi!HeZXigjb:meZgi!HiVX`L^hZ!I]Z;VhiZhiLVnid>cXgZVhZNdjg>ciZgcZiFjdi^Zci!IgVchEVi]!LZW:m!VcYi]ZLZW:m
HVc?dhZ!86
H^c\VedgZ
6bhiZgYVb!I]ZCZi]ZgaVcYh
ad\dVgZgZ\^hiZgZYigVYZbVg`hd[8^hXdHnhiZbh!>cX#VcY$dg^ihV[[^a^ViZh^ci]ZJc^iZYHiViZhVcYXZgiV^cdi]ZgXdjcig^Zh#
8^hXd]VhbdgZi]Vc'%%d[[^XZhldgaYl^YZ#6YYgZhhZh!e]dcZcjbWZgh!VcY[VmcjbWZghVgZa^hiZYdci]Z8^hXdLZWh^iZVilll#X^hXd#Xdb$\d$d[[^XZh#
6aadi]ZgigVYZbVg`hbZci^dcZY^ci]^hYdXjbZcidglZWh^iZVgZi]ZegdeZgind[i]Z^ggZheZXi^kZdlcZgh#I]ZjhZd[i]ZldgYeVgicZgYdZhcdi^beanVeVgicZgh]^egZaVi^dch]^eWZilZZc8^hXdVcYVcndi]ZgXdbeVcn#%-%.G
889:!88:CI!8^hXd:dh!8^hXdAjb^c!8^hXdCZmjh!8^hXdHiVY^jbK^h^dc!8^hXdIZaZEgZhZcXZ!8^hXdLZW:m!i]Z8^hXdad\d!98:!VcYLZaXdbZidi]Z=jbVcCZildg`VgZigVYZbVg`h08]Vc\^c\i]ZLVnLZLdg`!
Xd]VhbdgZi]Vc'%%d[[^XZhldgaYl^YZ#6YYgZhhZh!e]dcZcjbWZgh!VcY[VmcjbWZghVgZa^hiZYdci]Z8^hXdLZWh^iZVilll#X^hXd#Xdb$\d$d[[^XZh#
© 2009 Cisco Systems, Inc. All rights reserved.
OL-18475-01
Contents
Chapter 1: Getting to Know the WRP400
9
Front Panel
9
Back Panel
12
Side Panel
13
Placement Positions
13
Chapter 2: Before You Begin: Understanding Wireless Security
16
Change the Default Wireless Network Name or SSID
16
Change the Default Router Password
17
Enable MAC Address Filtering for Wireless Access
17
Enable Encryption
17
General Network Security Guidelines
18
Additional Security Tips
18
Chapter 3: Using the Web-Based Utility for Advanced Configuration
19
How to Access the Web-Based Utility
20
Chapter 4: Basic Settings
Setup > Basic Setup
23
Internet Setup
23
Network Setup
30
Time Setting
33
Setup > DDNS
Cisco WRP400 User Guide
22
34
DynDNS.org
34
TZO.com
36
Setup > MAC Address Clone
37
Setup > Advanced Routing
38
Advanced Settings: PPPoE Relay
39
Advanced Routing
39
i
Contents
Chapter 5: Installing and Configuring Your Mobile Network
41
Installing Your USB Modem
42
Setup > Mobile Network
43
Setup > Connection Recovery
46
Recovery & Failover
47
WAN Interfaces
48
Understanding the LED Behavior for Mobile Network
49
LED Behavior During USB Modem Installation
49
LED Behavior During Mobile Network Connectivity
49
Chapter 6: Configuring Your Wireless Network
Wireless > Basic Wireless Settings
51
Manual Configuration of the Network
52
Wi-Fi Protected Setup
54
Wireless > Wireless Security
56
WEP
57
WPA Personal
58
WPA2 Personal
59
WPA Enterprise
60
WPA2 Enterprise
61
Wireless > Wireless MAC Filter
62
Wireless > Advanced Wireless Settings
64
Chapter 7: Configuring Network Security and Controlling Internet Access
Security > Firewall
66
66
Firewall
67
Internet Filter
67
Web Filter
68
Security > VPN Passthrough
68
Access Restrictions > Internet Access
69
Creating or Modifying an Internet Access Policy
Cisco WRP400 User Guide
51
73
ii
Contents
Chapter 8: Configuring Applications and Gaming
Applications and Gaming > Single Port Forwarding
76
Applications and Gaming > Port Range Forward
77
Applications & Gaming > Port Range Triggering
79
Applications and Gaming > DMZ
80
Applications and Gaming > QoS
81
Chapter 9: Administration
Administration > Management
87
88
Management
89
IGMP
91
Administration > Log
91
Administration > Diagnostics
93
Ping Test
93
Traceroute Test
94
Administration > Factory Defaults
96
Administration > Firmware Upgrade
97
Username & Password
97
Firmware Upgrade
98
Administration > Config Management
99
Backup Configuration
100
Restore Configuration
100
Administration > Reboot
100
Chapter 10: Using the Status Screens
Status > Router
101
102
Router Information
102
Internet Connection
103
Status > Mobile Network
Cisco WRP400 User Guide
75
104
Mobile Network Status
104
Data Card Status
105
iii
Contents
Status > Local Network
106
Local Network
106
DHCP Server
106
Status > Wireless Network
Chapter 11: Configuring Voice Services
108
109
Access to the Voice Screens
109
Voice > Info
110
Product Information
111
System Status
111
Line 1/2 Status
112
Voice > System
113
System Configuration
114
Miscellaneous Settings
114
Voice > User 1/2
114
Call Forward Settings
116
Selective Call Forward Settings
116
Speed Dial Settings
116
Supplementary Service Settings
117
Distinctive Ring Settings
117
Ring Settings
117
Voice > Admin Login
118
Chapter 12: Interactive Voice Response Menu
119
Overview
119
Menu Commands
119
Appendix A:Troubleshooting
Cisco WRP400 User Guide
121
General Troubleshooting
121
Mobile Network Troubleshooting
125
iv
Contents
Appendix B:Specifications
128
Appendix C:Regulatory Information
134
Appendix D:Where to Go From Here
153
Cisco WRP400 User Guide
v
Preface
Finding Information in PDF Files
The WRP400 documents are published as PDF files. The PDF Find/Search tool
within Adobe® Reader® lets you find information quickly and easily online. You
can perform the following tasks:
•
Search an individual PDF file.
•
Search multiple PDF files at once (for example, all PDFs in a specific folder
or disk drive).
•
Perform advanced searches.
Finding Text in a PDF
Follow this procedure to find text in a PDF file.
STEP 1
Enter your search terms in the Find text box on the toolbar.
NOTE By default, the Find tool is available at the right end of the Acrobat toolbar. If the
Find tool does not appear, choose Edit > Find.
STEP 2
Optionally, click the arrow next to the Find text box to refine your search by
choosing special options such as Whole Words Only.
STEP 3
Press Enter.
STEP 4
Acrobat displays the first instance of the search term.
STEP 5
Press Enter again to continue to more instances of the term.
Cisco WRP400 User Guide
6
Preface
Finding Text in Multiple PDF Files
The Search window lets you search for terms in multiple PDF files that are stored
on your PC or local network. The PDF files do not need to be open.
STEP 1
Start Acrobat Professional or Adobe Reader.
STEP 2
Choose Edit > Search, or click the arrow next to the Find box and then choose
Open Full Acrobat Search.
STEP 3
In the Search window, complete the following steps:
a. Enter the text that you want to find.
b. Choose All PDF Documents in.
From the drop-down box, choose Browse for Location. Then choose the
location on your computer or local network, and click OK.
c. If you want to specify additional search criteria, click Use Advanced Search
Options, and choose the options you want.
d. Click Search.
Cisco WRP400 User Guide
7
Preface
STEP 4
When the Results appear, click + to open a folder, and then click any link to open
the file where the search terms appear.
For more information about the Find and Search functions, see the Adobe Acrobat
online help.
Cisco WRP400 User Guide
8
1
Getting to Know the WRP400
Thank you for choosing the Cisco WRP400 Wireless-G Broadband Router with 2
Phone Ports. The WRP400 lets you access the Internet via a wireless connection
or through one of its four switched ports. You can also use the WRP400 to share
resources such as computers, printers and files. The built-in phone adapter
enables Voice-over-IP (VoIP) calls even while you are using the Internet.
Front Panel
Cisco WRP400 User Guide
9
1
Getting to Know the WRP400
Front Panel
LED
Description
USB: For information about supported USB devices, visit the WRP400
product page on Cisco.com: http://www.cisco.com/en/US/products/
ps10028/index.html
Wi-Fi Protected Setup (White/Orange): If you have client devices,
such as wireless adapters, that support Wi-Fi Protected Setup, then
you can use Wi-Fi Protected Setup to automatically configure
wireless security for your wireless network(s).
To use Wi-Fi Protected Setup, run the Setup Wizard, or refer to
“Wireless > Basic Wireless Settings,” on page 39.
The Wi-Fi Protected Setup button lights up white and stays on while
wireless security is enabled on your wireless network(s). The LED
lights up orange if there is an error during the Wi-Fi Protected Setup
process. Make sure the client device supports Wi-Fi Protected
Setup. Wait until the LED is off, and then try again.
Power (Green/Red/Orange): This LED indicates the status of power
and the progress of the self-diagnostic test upon bootup. If a USB
modem is connected to the USB port, this LED indicates the progress
of initialization and the status of the mobile network connection.
Cisco WRP400 User Guide
•
Power: The Power LED shines green and stays on while the WRP400 is
powered on. If the LED shines red, verify that the correct power adapter
is used. If the LED remains red, contact your service provider for
support.
•
Self-diagnostic test: During boot-up, the LED flashes green to indicate
that the self-diagnostic test is in progress. When the test is complete,
the LED shines steady green.
•
Initialization of a USB modem: When you connect a device to the USB
port, the Power LED flashes green and orange, indicating that
initialization is in progress. After the device initializes, the Power LED
shines steady green. If the device fails to initialize, the LED continues to
flash green and orange.
10
1
Getting to Know the WRP400
Front Panel
LED
Description
•
Mobile network connection: If a USB modem is installed, the mobile
network connection is used as a failover when an Ethernet connection is
unavailable. The Power LED shows the status of the mobile network:
•
Flashing Orange: The WRP400 is attempting to connect to the
Internet through the mobile network connection.
•
Steady Orange: The WRP400 is connected to the Internet through
the mobile network connection.
•
Continuous Flashing Orange: The WRP400 failed to connect to the
Internet through the mobile network connection and is trying again.
•
Steady Green: If a USB device is connected, this LED behavior
indicates that the device was successfully initialized and that the
WRP400 is not using the mobile network connection. If the USB
device is removed, this LED behavior indicates that theWRP400 has
power.
Phone 1-2 (Green): The Phone 1 or 2 LED lights up and stays on
when an active line is registered to the corresponding port on the
back panel. The LED slowly flashes when voicemail messages are
waiting.
Wireless (Green): The Wireless LED lights up when the wireless
feature is enabled. It flashes when the WRP400 is actively sending or
receiving data over the network.
Ethernet 1-4 (Green): These numbered LEDs, corresponding with
the numbered ports on the back panel, serve two purposes. If the
LED is solidly lit, the WRP400 is connected to a device through that
port. It flashes to indicate network activity over that port.
Internet (Green): The Internet LED lights up and stays on when an
Internet connection is made through the Internet port. It flashes to
indicate network activity over the Internet port.
NOTE: The Power LED indicates Internet connectivity through the
mobile network connection. See the information for the Power LED in
this table.
Cisco WRP400 User Guide
11
1
Getting to Know the WRP400
Back Panel
Back Panel
Port
Description
Internet: Use this port to connect the WRP400 to a cable or DSL
Internet connection.
Phone 1-2: Use these ports to connect standard analog telephones
to the WRP400.
Ethernet 1, 2, 3, 4: Use these Ethernet ports to connect the WRP400
to wired computers and other Ethernet network devices.
Power: Use the power port to connect the power adapter.
Cisco WRP400 User Guide
12
1
Getting to Know the WRP400
Side Panel
Side Panel
Reset: There are two ways to reset the WRP400 to the factory
default settings. Either press and hold the Reset button for
approximately ten seconds, or restore the defaults from the
Administration >Factory Defaults screen of the administration web
server. (The Factory Defaults screen allows you to restore the router
and voice defaults separately.)
NOTE: Restoring the voice defaults may require your login (the
default user name and password are admin). If the defaults do not
work, contact your service provider for more information.
Stand: To place the WRP400 in a vertical position, rotate the stand 90
degrees.
Placement Positions
There are three ways to physically install the WRP400:
Cisco WRP400 User Guide
•
Horizontal Placement: The WRP400 has four rubber feet on the bottom
panel. Place the WRP400 on a level surface near an electrical outlet.
•
Vertical Placement: The WRP400 has a stand on the side panel opposite to
the antenna. Rotate the stand 90 degrees, and place the WRP400 on a level
surface near an electrical outlet.
•
Wall-Mounting Placement: The WRP400 has four wall-mount slots on its
back panel.
13
1
Getting to Know the WRP400
Placement Positions
Figure 1 Horizontal and Vertical Placement Options
To mount the WRP400 on a wall, follow these instructions:
STEP 1
Choose a wall that is smooth, flat, dry, and sturdy. Make sure that an electrical
outlet is nearby.
STEP 2
Obtain mounting hardware. Suggested hardware is illustrated below (not true to
scale).
Figure 2
Cisco WRP400 User Guide
Mounting Hardware
14
1
Getting to Know the WRP400
Placement Positions
STEP 3
Drill two holes, 60 mm (2.36 inches) apart. Insert a screw into each hole and leave
3 mm (0.12 inches) of the head exposed.
To create a template to position the screws, you can print this page at 100 percent.
Then cut along the dotted line. Affix this template to the wall where you want to
drill the holes.
Figure 3 Wall Mount Template
NOTE Cisco is not responsible for damages incurred by insecure wall-mounting
hardware.
STEP 4
Cisco WRP400 User Guide
Position the WRP400 so that two of the wall-mount slots are over the two screws.
Slide the WRP400 down until the screws fit snugly into the wall-mount slots.
15
2
Before You Begin: Understanding Wireless
Security
Wireless networks are convenient and easy to install, so homes with high-speed
Internet access are adopting them at a rapid pace. Because wireless networking
operates by sending information over radio waves, it can be more vulnerable to
intruders than a traditional wired network. Like signals from your cellular or
cordless phones, signals from your wireless network can also be intercepted.
Because you cannot physically prevent someone from connecting to your
wireless network, you need to take some additional steps to keep your network
secure.
NOTE The Setup Wizard guides you through the process of completing the tasks that are
described below. You are strongly encouraged to use the Setup Wizard for initial
configuration of the WRP400.
Change the Default Wireless Network Name or SSID
Wireless devices have a default wireless network name or Service Set Identifier
(SSID) set by the factory. This is the name of your wireless network, and can be up
to 32 characters in length. To distinguish your wireless network from other
wireless networks that may exist around you, you should change the default
wireless network name to something easily recognizable, but do not use personal
information (such as your Social Security number) because this information may
be available for anyone to see when browsing for wireless networks. For more
information, see “Wireless > Basic Wireless Settings,” on page 51.
Cisco WRP400 User Guide
16
Before You Begin: Understanding Wireless Security
Change the Default Router Password
2
Change the Default Router Password
When you connect to the administration web server, you will be asked for a
password. The WRP400 has a default password set by the factory. The default
password is admin. Hackers know the defaults and may try to use them to access
your wireless device and change your network settings. To prevent unauthorized
access, change the password to one that is hard to guess. For more information,
see “Administration > Management,” on page 88.
Enable MAC Address Filtering for Wireless Access
The Cisco WRP400 gives you the ability to enable Media Access Control (MAC)
address filtering. The MAC address is a unique series of numbers and letters
assigned to every networking device. With MAC address filtering enabled,
wireless network access is provided solely for wireless devices with specific
MAC addresses. For example, you can specify the MAC address of each
computer in your home so that only those computers can access your wireless
network. For more information, see “Wireless > Wireless MAC Filter,” on
page 62.
Enable Encryption
Encryption protects data transmitted over a wireless network. Wi-Fi Protected
Access (WPA/WPA2) and Wired Equivalency Privacy (WEP) offer different levels
of security for wireless communication.
A network encrypted with WPA/WPA2 is more secure than a network encrypted
with WEP, because WPA/WPA2 uses dynamic key encryption. To protect the
information as it passes over the airwaves, you should enable the highest level of
encryption supported by your network equipment.
WEP is an older encryption standard and may be the only option available on
some older devices that do not support WPA.
For more information, see “Wireless > Wireless Security,” on page 56.
Cisco WRP400 User Guide
17
Before You Begin: Understanding Wireless Security
General Network Security Guidelines
2
General Network Security Guidelines
Wireless network security is effective only when combined with good network
security practices.
•
Password protect all computers on the network and individually password
protect sensitive files.
•
Change passwords on a regular basis.
•
Install anti-virus software and personal firewall software.
•
Disable file sharing (peer-to-peer). Some applications may open file sharing
without your consent and/or knowledge.
Additional Security Tips
To help prevent security problems, follow these guidelines:
Cisco WRP400 User Guide
•
Keep wireless routers, access points, or gateways away from exterior walls
and windows.
•
Turn wireless routers, access points, or gateways off when they are not
being used (at night, during vacations).
•
Use strong passphrases that are at least eight characters in length.
Combine letters and numbers to avoid using standard words that can be
found in the dictionary.
18
3
Using the Web-Based Utility for Advanced
Configuration
After you set up the WRP400 with the Setup Wizard (located on the CD-ROM), the
router will be ready for use. However, if you’d like to change its advanced settings,
use the web-based utility. This chapter describes each web page of the utility and
each page’s key functions. You can access the utility via a web browser on a
computer connected to the router.
The web-based utility has these main tabs: Setup, Wireless, Security, Access
Restrictions, Applications & Gaming, Administration, Status, and Voice. Additional
tabs will be available after you click one of the main tabs.
NOTE When first installing the WRP400, you should use the Setup Wizard on the Setup
CD-ROM. If you want to configure advanced settings, use this chapter to learn
about the web-based utility.
The web-based utility has the following main tabs:
Cisco WRP400 User Guide
•
Setup: On the Setup screens, you can configure general settings, such as
Internet connection, IP address, DHCP server settings, DDNS, time settings,
and advanced router settings. For more information, see Chapter 4, “Basic
Settings.”
•
Mobile Network: You can connect a compatible Mobile Broadband USB
modem to the USB port of the WRP400 and configure the mobile network
connection.For more information, see Chapter 5, “Installing and
Configuring Your Mobile Network.”
•
Wireless: You can use the Wireless screens to set up and secure your
wireless network.For more information, see Chapter 6, “Configuring Your
Wireless Network.”
•
Security and Access Restrictions: You can use the Security screens to
enable a firewall, add filters, or allow VPN tunnels. You can use the Access
Restrictions screen to control Internet usage.For more information, see
19
Using the Web-Based Utility for Advanced Configuration
How to Access the Web-Based Utility
3
Chapter 7, “Configuring Network Security and Controlling Internet
Access.”
•
Applications & Gaming: You can use the Applications and Gaming screens
to configure your WRP400 to support applications, services, and gaming.
For more information, see Chapter 8, “Configuring Applications and
Gaming.”
•
Administration: You can use the Administration screens to manage access,
configure Universal Plug and Play, support multimedia streaming, enable
logging and diagnostics, restore factory default settings, upgrade firmware,
and back up and restore configurations. For more information, see
Chapter 9, “Administration.”
•
Status: You can use the Status screens to view information about your
WRP400. For more information, see Chapter 10, “Using the Status
Screens.”
•
Voice: You can use the Voice screens to manage the voice gateway
features of the WRP400.For more information, see Chapter 11,
“Configuring Voice Services.”
How to Access the Web-Based Utility
To access the web-based utility, launch the web browser on your computer, and
enter the default IP address of the WRP400, 192.168.15.1, in the Address field.
Then press Enter.
NOTE If you place the WRP400 behind a primary router with the IP address of
192.168.15.1, then the WRP400 will automatically assume a new default IP address,
192.168.16.1.
When the login screen appears, use the default user name and password, admin.
Then click OK to continue. Later, you can set a new password from the
Administration tab > Management page. See “Administration > Management,”
on page 88.
Cisco WRP400 User Guide
20
Using the Web-Based Utility for Advanced Configuration
How to Access the Web-Based Utility
Figure 4
Cisco WRP400 User Guide
3
Web-Based Utility Login Window
21
4
Basic Settings
On the Setup screens, you can configure general settings, such as Internet
connection, IP address, DHCP server settings, DDNS, time settings, and advanced
router settings.
?
How Do I...
•
Change the Internet Connection type, IP address,
DHCP Server settings, and other basic settings?
See “Setup > Basic Setup,” on page 23.
•
Set up DDNS for my web server or FTP server?
See “Setup > DDNS,” on page 34.
•
Clone a MAC address to access my Internet service?
See “Setup > MAC Address Clone,” on page 37.
•
Change the time settings?
See “Time Setting,” on page 33.
•
Configure advanced settings for PPPoE Relay, NAT,
Dynamic Routing (RIP), or Static Routing?
See “Setup > Advanced Routing,” on page 38.
NOTE For information about using the Setup screens to configure mobile network
settings, see Chapter 5, “Installing and Configuring Your Mobile Network.”
Cisco WRP400 User Guide
22
4
Basic Settings
Setup > Basic Setup
Setup > Basic Setup
You can use the Basic Setup page to configure the Internet connection and local
network settings. Complete the following sections of the page:
•
Internet Setup
•
Network Setup
•
Time Setting
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Internet Setup
You can use the Internet Setup section to configure the WRP400 for your Internet
connection. Most of the entries in this section require information that you can
obtain from your service provider.
Internet Connection Type
Select the type of Internet connection that your service provider supports:
•
Automatic Configuration - DHCP
•
Static IP
•
PPPoE
•
PPTP
•
L2TP
•
Telstra Cable
Automatic Configuration - DHCP
By default, the Internet Connection Type is set to Automatic Configuration - DHCP,
which should be kept only if your service provider supports DHCP or you are
connecting through a dynamic IP address.
This option usually applies to cable connections.
Cisco WRP400 User Guide
23
4
Basic Settings
Setup > Basic Setup
Figure 5 Setup > Basic Setup > Internet Connection Type > Automatic
Configuration - DHCP
Static IP
If you are required to use a permanent IP address to connect to the Internet, select
Static IP.
Figure 6
Setup > Basic Setup > Internet Connection Type > Static IP
Enter the information that was provided by your service provider.
Cisco WRP400 User Guide
•
Internet IP Address: The IP address of your WRP400, as seen from the
Internet.
•
Subnet Mask: The subnet mask, as seen by users on the Internet (including
your service provider).
•
Default Gateway: The IP address of your service provider server.
24
4
Basic Settings
Setup > Basic Setup
PPPoE
Some DSL-based service providers use PPPoE (Point-to-Point Protocol over
Ethernet) to establish Internet connections. If you are connected to the Internet
through a DSL line, check with your service provider to see if they use PPPoE. If
they do, you will have to enable PPPoE.
This option applies to some DSL services.
Figure 7 Setup > Basic Setup > Internet Connection Type > PPPoE
Enter the information that was provided by your service provider, and select the
Connect On Demand or Keep Alive feature, if desired.
Cisco WRP400 User Guide
•
User Name and Password: The login information for your account.
•
Service Name (Optional): The service name (if provided).
•
Connect on Demand: Max Idle Time: A feature that allows your WRP400 to
re-establish a terminated connection when a user attempts to access the
Internet. To enable this feature, select Connect on Demand. Use the Max
Idle Time field to specify the period of inactivity that causes a connection to
terminate. Keep the default Max Idle Time of 5 minutes, or specify the
maximum period of inactivity that you want to allow.
•
Keep Alive: Redial Period: A feature that allows your WRP400 to check
your Internet connection at a specified interval (Redial Period). If you are
disconnected, then the WRP400 automatically re-establishes your
connection. To enable this option, select Keep Alive. Keep the default Redial
Period of 30 seconds, or specify the interval at which you want the WRP400
to check the Internet connection.
25
4
Basic Settings
Setup > Basic Setup
PPTP
Point-to-Point Tunneling Protocol (PPTP) is a service that applies to connections in
Europe only.
Figure 8
Setup > Basic Setup > Internet Connection Type > PPTP
Enter the information that was provided by your service provider, and select the
Connect On Demand or Keep Alive feature, if desired.
Cisco WRP400 User Guide
•
Internet IP Address: The IP address of your WRP400, as seen from the
Internet.
•
Subnet Mask: The subnet mask, as seen by users on the Internet (including
your service provider).
•
Default Gateway: The IP address of your service provider server.
•
User Name and Password: The login information for your account.
•
Connect on Demand: Max Idle Time: A feature that allows your WRP400 to
re-establish a terminated connection when a user attempts to access the
Internet. To enable this feature, select Connect on Demand. Use the Max
Idle Time field to specify the period of inactivity that causes a connection to
terminate. Keep the default Max Idle Time of 5 minutes, or specify the
maximum period of inactivity that you want to allow.
•
Keep Alive: Redial Period: A feature that allows your WRP400 to check
your Internet connection at a specified interval (Redial Period). If you are
disconnected, then the WRP400 automatically re-establishes your
connection. To enable this option, select Keep Alive. Keep the default Redial
Period of 30 seconds, or specify the interval at which you want the WRP400
to check the Internet connection.
26
4
Basic Settings
Setup > Basic Setup
L2TP
L2TP is a service that applies to connections in Europe and Israel.
Figure 9
Setup > Basic Setup > Internet Connection Type > L2TP
Enter the information that was provided by your service provider, and select the
Connect On Demand or Keep Alive feature, if desired.
Cisco WRP400 User Guide
•
Server IP Address: The IP address of the L2TP Server.
•
User Name and Password: The login information for your account.
•
Connect on Demand: Max Idle Time: A feature that allows your WRP400 to
re-establish a terminated connection when a user attempts to access the
Internet. To enable this feature, select Connect on Demand. Use the Max
Idle Time field to specify the period of inactivity that causes a connection to
terminate. Keep the default Max Idle Time of 5 minutes, or specify the
maximum period of inactivity that you want to allow.
•
Keep Alive: Redial Period: A feature that allows your WRP400 to check
your Internet connection at a specified interval (Redial Period). If you are
disconnected, then the WRP400 automatically re-establishes your
connection. To enable this option, select Keep Alive. Keep the default Redial
Period of 30 seconds, or specify the interval at which you want the WRP400
to check the Internet connection.
27
4
Basic Settings
Setup > Basic Setup
Telstra Cable
Telstra Cable is a service used in Australia only.
Figure 10
Setup > Basic Setup > Internet Connection Type > Telstra Cable
Enter the information that was provided by your service provider, and select the
Connect On Demand or Keep Alive feature, if desired.
Cisco WRP400 User Guide
•
Heart Beat Server: The IP address of the Heart Beat Server.
•
User Name and Password: The login information for your account.
•
Connect on Demand: Max Idle Time: A feature that allows your WRP400 to
re-establish a terminated connection when a user attempts to access the
Internet. To enable this feature, select Connect on Demand. Use the Max
Idle Time field to specify the period of inactivity that causes a connection to
terminate. Keep the default Max Idle Time of 5 minutes, or specify the
maximum period of inactivity that you want to allow.
•
Keep Alive: Redial Period: A feature that allows your WRP400 to check
your Internet connection at a specified interval (Redial Period). If you are
disconnected, then the WRP400 automatically re-establishes your
connection. To enable this option, select Keep Alive. Keep the default Redial
Period of 30 seconds, or specify the interval at which you want the WRP400
to check the Internet connection.
28
4
Basic Settings
Setup > Basic Setup
Optional Settings
Some of these settings may be required by your service provider. Verify with your
service provider before making any changes.
Figure 11 Setup > Basic Setup > Optional Settings
•
Host Name and Domain Name: A host and domain name for the WRP400.
Some service providers, usually cable service providers, require these
names as identification. In most cases, leaving these fields blank will work.
•
MTU: MTU is the Maximum Transmission Unit. The largest packet size that
is permitted for Internet transmission. Select Manual if you want to manually
enter the largest packet size that is transmitted. To have the WRP400 select
the best MTU for your Internet connection, keep the default setting, Auto.
•
Size: When Manual is selected in the MTU field, this option is enabled.
Leave this value in the 576 to 1500 range. The default size depends on the
Internet Connection Type:
•
Cisco WRP400 User Guide
-
DHCP or Static IP: 1500
-
PPPoE: 1492
-
PPTP or L2TP: 460
-
Telstra Cable: 1500
Static DNS 1-3: The Domain Name System (DNS) is how the Internet
translates domain or website names into Internet addresses or URLs. Enter
the IP address of the DNS server, which is provided by your service
provider. If you wish to use a different DNS server, enter its IP address in one
of these fields. You can enter up to three DNS server IP addresses here. The
WRP400 will use these for quicker access to functioning DNS servers. By
default, the WRP400 uses 192.168.15.1 for DNS.
29
4
Basic Settings
Setup > Basic Setup
Network Setup
You can use the Network Setup section to change the IP address of the WRP400
and configure the DHCP server settings.
NOTE For wireless setup, use the Wireless tab. See Chapter 6, “Configuring Your
Wireless Network.”
Router IP
You can enter the Local IP Address and Subnet Mask of the WRP400, as seen by
your network.
Figure 12
Setup > Basic Setup > Network Setup
DHCP Server Setting
You can use these settings to configure the Dynamic Host Configuration Protocol
(DHCP) server function. The WRP400 can be used as a DHCP server for your
network. A DHCP server automatically assigns an IP address to each computer on
your network.
NOTE If you choose to enable the DHCP server option, make sure there is no other DHCP
server on your network.
Cisco WRP400 User Guide
30
4
Basic Settings
Setup > Basic Setup
Figure 13
Setup > Basic Setup > DHCP Server Setting
•
DHCP Server: DHCP is enabled by factory default. If you already have a
DHCP server on your network, or you don’t want a DHCP server, then select
Disabled (no other DHCP features will be available).
•
DHCP Reservation: Click this button if you want to reserve IP addresses for
clients. See “DHCP Reservation,” on page 32.
•
DNS Proxy: To enable the DNS Proxy feature, select Enabled. To disable the
DNS Proxy feature, keep the default, Disabled.
NOTE The DNS proxy relays DNS requests to the current public network
DNS server for the proxy, and it replies as a DNS resolver to the client
device on the network.
Cisco WRP400 User Guide
•
Starting IP Address: Enter a value for the DHCP server to start with when
issuing IP addresses. The Starting IP Address must be greater than the
default IP address of the WRP400, 192.168.15.1, and less than
192.168.15.253. The default Starting IP Address is 192.168.15.100.
•
Maximum DHCP Users: Enter the maximum number of computers that will
receive IP addresses from the DHCP server. This number cannot be greater
than 253. The default is 50.
•
IP Address Range: You can view the range of available IP addresses.
•
Client Lease Time: Enter the maximum connection time in minutes that a a
dynamic IP address is “leased” to a network user. When the time elapses,
the user is automatically assigned a new dynamic IP address. The default is
0 minutes, which means one day.
31
4
Basic Settings
Setup > Basic Setup
•
Static DNS: Enter the local IP address of the DNS server, which is provided
by your service provider. If you wish to use a different DNS server, enter that
IP address in this field.
NOTE The Domain Name System (DNS) is how the Internet translates
domain or website names into Internet addresses or URLs.
•
WINS: If you use a WINS server, enter that server’s IP address here.
Otherwise, when DHCP is enabled, the field is field with the value 0.0.0.0.
NOTE The Windows Internet Naming Service (WINS) manages each PC’s
interaction with the Internet. I
DHCP Reservation
This page appears if you click the DHCP Reservation button on the Basic Setup
page. Use this page to assign a fixed local IP address to a computer on the
network.
Figure 14
Cisco WRP400 User Guide
DHCP Reservation
32
4
Basic Settings
Setup > Basic Setup
•
Select Clients from DHCP Tables: To reserve an IP address for a client in
the table, check the Select check box, and then click Add Clients.
•
Manually Adding Client: To reserve an IP address for a client that is not
listed in the Select Clients table, enter the Client Name, the desired IP
Address, and the client MAC Address in the Manually Adding Client section.
Then click Add.
•
Clients Already Reserved: If you want to remove a client from this list, click
Remove.
Click Save Setting to apply your changes, or click Cancel Changes to
cancel your changes. To view the most up-to-date information, click
Refresh. To exit this screen, click Close.
Time Setting
In the Time Setting section of the Basic Setup page, you can choose your time
zone and Time Server Address, if needed.
Figure 15
Cisco WRP400 User Guide
Setup > Basic Setup > Time Setting
•
Time Zone: Select the time zone for the location.
•
Automatically adjust clock for daylight saving changes: Select this option
if you want the WRP400 to automatically adjust the clock for daylight saving
time. This option is enabled by default.
•
Time Server Address: If you want to use the default Network Time Protocol
(NTP) server, keep the default, Auto. If you want to specify the NTP server,
select Manual, and enter the URL or IP address of the NTP server that you
want to use.
•
Resync Timer: Enter the number of seconds that elapse before the
WRP400 resyncs with the NTP server. The default is 3600 seconds.
33
4
Basic Settings
Setup > DDNS
Setup > DDNS
You can use the DDNS page to configure the Dynamic Domain Name System
(DDNS) feature. DDNS lets you assign a fixed host and domain name to a dynamic
Internet IP address. It is useful when you are hosting your own website, FTP server,
or other server behind the WRP400.
Before you can use this feature, you need to sign up for DDNS service with a DDNS
service provider, such as www.dyndns.org or www.TZO.com. If you do not want to
use this feature, keep the default setting, Disabled.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Choose your DDNS service from the drop-down list, and then enter the
information for your service.
DynDNS.org
Figure 16
Cisco WRP400 User Guide
Setup > DDNS > DynDNS.org
34
4
Basic Settings
Setup > DDNS
Cisco WRP400 User Guide
•
User Name: Enter the User Name for your DDNS account.
•
Password: Enter the Password for your DDNS account.
•
Host Name: Enter the DDNS URL assigned by the DDNS service.
•
System: Choose the DynDNS service you use: Dynamic, Static, or Custom.
The default selection is Dynamic.
•
Mail Exchange (Optional): Enter the address of your mail exchange server,
so emails to your DynDNS address go to your mail server.
•
Backup MX: This feature allows the mail exchange server to be a backup.
To enable the feature, select Enabled. To disable this feature, keep the
default, Disabled. If you are not sure which setting to use, keep the default,
Disabled.
•
Wildcard: This setting enables or disables wildcards for your host. For
example, if your DDNS address is myplace.dyndns.org and you enable
wildcards, then x.myplace.dyndns.org will work as well (x is the wildcard).
To enable wildcards, select Enabled. To disable wildcards, keep the default,
Disabled. If you are not sure which setting to use, keep the default, Disabled.
•
Internet IP Address: The Internet IP address of the WRP400 is displayed
here. Because it is dynamic, it will change.
•
Status: The status of the DDNS service connection is displayed here.
•
Update: To manually trigger an update, click this button.
35
4
Basic Settings
Setup > DDNS
TZO.com
Figure 17 Setup > DDNS > TZO.com
Cisco WRP400 User Guide
•
E-mail Address, TZO Key, and Domain Name: Enter the settings for your
account with TZO.
•
Internet IP Address: The Internet IP address of the WRP400 is displayed
here. Because it is dynamic, it will change.
•
Status: The status of the DDNS service connection is displayed here.
•
Update: To manually trigger an update, click this button.
36
4
Basic Settings
Setup > MAC Address Clone
Setup > MAC Address Clone
A MAC address is a unique 12-digit code that is assigned to a piece of hardware
for identification. Some service providers require you to register a MAC address in
order to access the Internet. If you previously registered a MAC address with your
service provider for this purpose, you can reassign that MAC address to the
WRP400. In this sense, you are “cloning” the MAC address to be used by this
router.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 18
Cisco WRP400 User Guide
Setup > MAC Address Clone
•
Enabled, Disabled: To assign a previously registered MAC address to the
WRP400, select Enabled. Otherwise, select Disabled.
•
MAC Address: Enter the MAC address that you previously registered with
your service provider.
•
Clone Your PC’s MAC: Click this button to clone the MAC address of the
computer you are using.
37
4
Basic Settings
Setup > Advanced Routing
Setup > Advanced Routing
You can use the Advanced Routing page to set up PPPoE Relay, NAT, Dynamic
Routing (RIP), or Static Routing.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 19
Cisco WRP400 User Guide
Setup > Advanced Routing
38
4
Basic Settings
Setup > Advanced Routing
Advanced Settings: PPPoE Relay
The PPPoE Relay feature enables an L2TP Access Concentrator (LAC) to relay
active discovery and service selection functionality for PPP over Ethernet (PPPoE),
over a Layer 2 Tunneling Protocol (L2TP) control channel, to an L2TP Network
Server (LNS) or tunnel switch (multihop node). The relay functionality of this
feature allows the LNS or tunnel switch to advertise its services to the client,
thereby providing end-to-end control of services between the LNS and a PPPoE
client.
To enable the PPPoE Relay feature for the Internet side, select Enabled. To disable
the PPPoE Relay feature, keep the default, Disabled.
Advanced Routing
Choose the features that you want to enable.
Cisco WRP400 User Guide
•
NAT: If the WRP400 is hosting your network’s connection to the Internet,
keep the default, Enabled. If another router exists on your network, select
Disabled. When the NAT setting is disabled, dynamic routing will be
enabled.
•
Dynamic Routing (RIP): This feature enables the WRP400 to automatically
adjust to physical changes in the network’s layout and exchange routing
tables with the other router(s). The WRP400 determines the route of the
network packets based on the fewest number of hops between the source
and the destination. When the NAT setting is enabled, the Dynamic Routing
feature is automatically disabled. When the NAT setting is disabled, this
feature is available. Select Enabled to use the Dynamic Routing feature.
•
Static Routing: A static route is a pre-determined pathway that network
information must travel to reach a specific host or network. Enter the
information described below to set up a new static route.
-
Route Entries: To set up a static route between the WRP400 and
another network, select a number from the drop-down list. Click Delete
This Entry to delete a static route.
-
Enter Route Name: Enter a name for the Route here, using a maximum of
25 alphanumeric characters.
-
Destination LAN IP: The Destination LAN IP is the address of the
remote network or host to which you want to assign a static route.
39
4
Basic Settings
Setup > Advanced Routing
•
-
Subnet Mask: The Subnet Mask determines which portion of a
Destination LAN IP address is the network portion, and which portion is
the host portion.
-
Gateway: This is the IP address of the gateway device that allows for
contact between the WRP400 and the remote network or host.
-
Interface: This interface tells you whether the Destination LAN IP
address is on the LAN and Wireless (Ethernet and wireless networks) or
the Internet (WAN).
Show Routing Table: Click this button to view the static routes you have
already set up.
For each route, the Destination LAN IP address, Subnet Mask, Gateway, and
Interface are displayed. Click Refresh to update the information. Click Close
to exit this screen.
Figure 20
Cisco WRP400 User Guide
Routing Table
40
5
Installing and Configuring Your Mobile
Network
You can connect a compatible Mobile Broadband USB modem to the USB port of
the WRP400 and configure the mobile network connection.
?
Cisco WRP400 User Guide
How Do I...
•
Connect a USB modem to my WRP400?
See “Installing Your USB Modem,” on page 42
•
Enter the account information for my mobile
network connection?
See “Setup > Mobile Network,” on page 43
•
Ensure continued Internet access through the
mobile network connection and the Ethernet
connection?
See “Setup > Connection Recovery,” on page 46
•
Know when the WRP400 is connected to the
Internet through the mobile network?
See “Understanding the LED Behavior for Mobile
Network,” on page 49
41
Installing and Configuring Your Mobile Network
Installing Your USB Modem
5
Installing Your USB Modem
You can install a compatible Mobile Broadband USB Modem into the USB port of
the WRP400 for the purpose of accessing a mobile network.
NOTE For more information about compatible USB devices, visit the WRP400 product page on
Cisco.com: http://www.cisco.com/en/US/products/ps10028/index.html
Connect a compatible USB Modem into the USB port of the WRP400. The Power
LED flashes green and orange, indicating that a device is connected to the USB
port and that initialization is in progress.
After the device initializes, the Power LED shines steady green. If the device fails
to initialize, the LED continues to flash green and orange.
By default, the WRP400 connects to the Internet through the local Ethernet, if available. The
mobile network connection is used as a failover when an Ethernet connection is unavailable.
NOTE For more information about configuring your mobile network, see “Setup > Mobile
Network,” on page 43.
Cisco WRP400 User Guide
42
Installing and Configuring Your Mobile Network
Setup > Mobile Network
5
Setup > Mobile Network
You can use this page to choose the connect mode and to enter the settings for
the mobile network. You also can use this page to view the current connection
status.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 21 Setup > Mobile Network
NOTE Ethernet Connection Recovery and Interface Connection Failover will work only if
the Connection Mode is set to Auto. For more information about these features, see
“Setup > Connection Recovery,” on page 46..
Cisco WRP400 User Guide
43
Installing and Configuring Your Mobile Network
Setup > Mobile Network
•
5
Connect Mode:
-
Select Auto to enable your modem to establish connection
automatically.
-
Select Manual to connect or disconnect your modem connection
manually.
-
If you change your selection from Auto to Manual, a message appears.
Click OK to acknowledge that Connection Recover will be disabled, or
click Cancel to cancel.
-
If you change your selection from Manual to Auto, a message appears.
Click OK to also enable Ethernet Connection Recovery, or click Cancel
to set the Connect Mode to Auto without enabling Ethernet Connection.
•
Connect on Demand with Max. Idle Time: You can configure the WRP400
to terminate the Internet connection after it has been inactive for a specified
period of time (Max Idle Time). If your Internet connection has been
terminated due to inactivity, Connect on Demand enables the modem to
automatically re-establish a terminated connection when a user attempts to
access the Internet again. To enable this feature, select Connect on
Demand. In the Max Idle Time field, enter the number of minutes that can
elapse without activity before your Internet connection terminates. The
default Max Idle Time is 5 minutes.
•
Keep Alive: If you select this option, the WRP400 will periodically check
your Internet connection. If you are disconnected, then the WRP400 will
automatically re-establish your connection.
•
Card Status: This field shows the current modem connection status as
Detecting, Connecting, or Connected. If your Connect Mode is Manual, there
will be a button for you to click to connect or disconnect your Modem.
•
Configure Mode: Select Auto to allow the WRP400 to automatically detect
which card model was inserted and which carrier is available. Select
Manual to set up the connection manually. To allow the WRP400 to
automatically configure modem & mobile network settings, keep the
default, Auto.
NOTE Some Internet Service Providers (ISPs) will require that you enter
specific information, such as User Name and Password. This
information can be obtained from your ISP, if required.
Cisco WRP400 User Guide
44
Installing and Configuring Your Mobile Network
Setup > Mobile Network
Cisco WRP400 User Guide
5
•
Card Model: The data card model that is inserted in the USB port.
•
Carrier: The mobile network service provider for Internet connection. This
setting is required when you are using HSDPA/UMTS/GPRS Internet
service.
•
Country: Select the card issue country from the first drop-down menu.
•
Carrier: Select the card issue provider from the second drop-down menu.
•
Access Point Name (APN): The Internet network to which the mobile
device is connecting to. Enter the Access Point Name provided by your
mobile network service provider.
•
Dial Number: The dial number for the Internet connection. Enter the Dial
Number provided by your mobile network service provider.
•
Optional Settings: Some of these settings may be required by your mobile
network service provider. Verify with your mobile network service provider
before making any changes.
•
User Name and Password (Optional): Enter the User Name provided by
your mobile network service provider.
•
SIM PIN (Optional): The PIN code associated with your SIM card. Enter
your SIM PIN number here.
•
Server Name (Optional): The name of the server for the Internet
connection.
•
Authentication: The type of authentication used by your service provider.
Select your authentication type, if you do not know which type to use, keep
the default setting, Auto.
•
Service Type: Select the most commonly available type of mobile data
service connection based on your area service signal. If your location
supports only one mobile data service, you may set up for enhance build up
connection. The first selection will always search for HSPDA/3G/UMTS
service or switch to GPRS automatically only when it is available.
45
Installing and Configuring Your Mobile Network
Setup > Connection Recovery
5
Setup > Connection Recovery
An Internet connection can be established via the Ethernet Internet port or a USB
modem connected to the USB port. While both Ethernet and USB interfaces may
be connected, only one of them can be used to establish a link at a time.
By default, the WRP400 uses the Ethernet Internet connection when available. If
the Ethernet Internet connection fails, the WRP400 automatically attempts to bring
up another connection on another interface. This feature is called failover.
Whenever the Ethernet Internet connection recovers, the WRP400 automatically
attempts to bring back and recover the Ethernet Internet connection. This feature
is called Recovery.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 22
Cisco WRP400 User Guide
Setup > Connection Recovery
46
Installing and Configuring Your Mobile Network
Setup > Connection Recovery
5
Recovery & Failover
•
Ethernet Connection Recovery: This feature ensures that your Internet
connection is made through the Ethernet interface if it is available. Enabling
this feature also enables the Interface Connection Failover, which ensures
that if the Internet connection fails on the Ethernet interface, the WRP400
automatically attempts to bring up the connection through the mobile
network if available. Whenever the Ethernet Internet connection recovers,
the WRP400 automatically attempts to bring back and recover the Ethernet
Internet connection.
NOTE Ethernet Connection Recovery requires that your Mobile Connection
Mode is set to Auto and your Ethernet interface is set to the high
priority. When you enable this feature, a message appears. Click OK
to confirm that you want to change the Mobile Connection Mode and
the Ethernet interface priority.
Cisco WRP400 User Guide
•
Interface Connection Failover: Failover detection works by detecting the
physical connection and/or presence of traffic on the Internet link. If the link
is idle for some time, the WRP400 will attempt to ping a destination. If the
ping does not reply, the WRP400 assumes the link is down and attempts to
fail over to another interface. Click Enabled if you want to use this feature, or
otherwise click Disabled. This feature is automatically enabled if you enable
Ethernet Connection Recovery.
•
Timeout: Specify the time interval at which the WRP400 detects the status
of the Internet connection. The default timeout interval is 60 seconds.
•
Failover Validation Site: A ping target for the WRP400 to use to detect the
status of the Internet connection. By default the WRP400 pings the Network
Time Protocol (NTP) servers. You may specify a different IP address as a
target here.
47
Installing and Configuring Your Mobile Network
Setup > Connection Recovery
5
WAN Interfaces
The Summary table includes one row of information for the Ethernet interface and
one row of information for the USB interface.
•
Status: The link status of this interface:
-
Disconnected: The device is plugged in and available but not active.
-
Connecting: The WRP400 is attempting to bring up the link over the
device.
-
Connected: The link is up and running on the device.
-
Wait Recovery: When the WRP400 is connected to the Ethernet, this
status means that the Ethernet is waiting recovered to route to the
Failover Validation Site.
NOTE You can click the Status hyperlink to view the Status page for the
interface. To return to the Connection Recovery screen, click the Back
button on the browser toolbar. For more information, see“Router
Information,” on page 102 and “Mobile Network Status,” on
page 104 .
•
Priority: The priority setting determines which interface is used when both
interfaces are available. By default, the Ethernet interface has top priority.
However, you can change the priority setting by clicking Up to move an
interface to the top priority level or by clicking Down to move an interface to
the low priority level.
NOTE The interface priority setting is configurable only when Ethernet
Connection Recovery is disabled.
Cisco WRP400 User Guide
48
Installing and Configuring Your Mobile Network
Understanding the LED Behavior for Mobile Network
5
Understanding the LED Behavior for Mobile Network
The Internet LED indicates connectivity to the Internet through the Ethernet
connection only. The Power LED indicates the progress of USB initialization or the
status of the mobile network connection.
LED Behavior During USB Modem Installation
The Power LED indicates the progress of the initialization.
•
Before you connect the USB modem, the Power LED shines steady green to
show that the WRP400 has power.
•
After you connect the USB modem, the Power LED flashes green and
orange to show that a device is connected to the USB port and that
initialization is in progress.
•
If the initialization is successful, the Power LED shines steady green. If the
initialization fails, the LED continues to flash green and orange.
By default, the WRP400 connects to the Internet through the wired Ethernet, if
available. The mobile network connection is used as a failover when an Ethernet
connection is unavailable.
LED Behavior During Mobile Network Connectivity
After you successfully install a USB modem, the Power LED indicates the status of
the mobile network connection:
•
Flashing Orange: The WRP400 is attempting to connect to the Internet
through the mobile network connection.
•
Steady Orange: The WRP400 is connected to the Internet through the
mobile network connection.
•
Continuous Flashing Orange: The WRP400 failed to connect to the Internet
through the mobile network connection and is trying again.
•
Steady Green:
-
Cisco WRP400 User Guide
If a USB device is connected, this LED behavior indicates that the device
was successfully initialized and that the WRP400 is not using the mobile
network connection. If an Internet connection is active through the
Ethernet, then the Internet LED is illuminated.
49
Installing and Configuring Your Mobile Network
Understanding the LED Behavior for Mobile Network
-
5
If the USB device was removed, this LED behavior indicates that the
WRP400 has power.
To check the status of the USB Modem, or modify the settings for the mobile
network, connection recovery, and failover, you can use the administration web
server.
Cisco WRP400 User Guide
50
6
Configuring Your Wireless Network
You can use the Wireless screens to set up and secure your wireless network.
?
How Do I...
•
Set up my wireless network?
See “Wireless > Basic Wireless Settings,” on
page 51.
•
Secure my wireless network?
See “Wireless > Wireless Security,” on page 56.
•
Specify computers that can or cannot access my
network?
See “Wireless > Wireless MAC Filter,” on page 62
•
Configure special router functions for my wireless
network?
See “Wireless > Advanced Wireless Settings,” on
page 64.
Wireless > Basic Wireless Settings
You can use the Basic Wireless Settings page to configure your wireless network
manually or to use Wi-Fi Protected Setup.
Figure 23
Cisco WRP400 User Guide
Wireless > Basic Wireless Settings > Wireless Configuration
51
Configuring Your Wireless Network
Wireless > Basic Wireless Settings
6
The options on the page change after you choose Manual or Wi-Fi Protected
Setup.
•
Choose Manual if you want to manually configure your network, if you are
setting up your secondary network (SSID2), of if you do not have client
devices that support Wi-Fi Protected Setup. See “Manual Configuration of
the Network,” on page 52.
•
Choose Wi-Fi Protected Setup if you have client devices, such as wireless
adapters, that support Wi-Fi Protected Setup. For more information, see
“Wi-Fi Protected Setup,” on page 54.
Manual Configuration of the Network
After you choose Manual for the Wireless Configuration method, additional fields
appear. You can change the SSID of the wireless network and enable a second
network, or guest network.
Figure 24
Cisco WRP400 User Guide
Wireless > Basic Wireless Settings > Manual Configuration
•
Network Mode: Select the wireless standards that are running on your
network. If you have Wireless-G and Wireless-B devices, keep the default
setting, Mixed. If you have only Wireless-G devices, select Wireless-G only.
If you have only Wireless-B devices, select Wireless-B only.
•
Wireless Channel: Select the channel that you want to use. To allow the
WRP400 to select the best available wireless channel, keep the default,
Auto.
52
6
Configuring Your Wireless Network
Wireless > Basic Wireless Settings
•
SSID1, SSID2: The SSID is the network name shared among all devices in a
wireless network. The WRP400 can support up to two wireless networks.
By default, one wireless network is enabled, and you can create a second
wireless network.
Configure the following settings for each wireless network:
-
Wireless Network Name (SSID): The default wireless network uses
this name: “cisco” followed by the last four digits of the wireless MAC
address of the WRP400. To rename the default wireless network, enter a
unique Wireless Network Name, which is case-sensitive and must not
exceed 32 characters. You can use any of the characters on the
keyboard. To create a second wireless network, select Network Enabled
for the SSID2 setting. Then enter a unique Wireless Network Name.
NOTE If you are unable to configure the SSID2 settings, contact your service
provider for more information.
-
SSID Broadcast Enabled: When wireless clients survey the local area
for wireless networks, they detect the SSID broadcast by the WRP400. If
you want to broadcast the SSID, keep the check box selected. If you do
not want to broadcast the SSID, deselect the check box.
-
For Internet Access Only: On your second wireless network (SSID2),
you can set up guest access, which allows access to the Internet while
blocking access to your local network. For example, a guest cannot
access the data stored on your local computers. To limit guests to
Internet access only, keep the check box selected. To allow local
network access, deselect the check box.
NOTE The For Internet Access Only feature applies only to SSID2.
-
Cisco WRP400 User Guide
Network Enabled: To enable the wireless network, select the check
box. To disable the wireless network, deselect the check box.
53
6
Configuring Your Wireless Network
Wireless > Basic Wireless Settings
Wi-Fi Protected Setup
After you choose Wi-Fi Protected Setup for the Wireless Configuration, the
instructions, fields, and buttons appear on the screen. Three setup methods are
available.
NOTE Wi-Fi Protected Setup is available for your primary wireless network
(SSID1) only. To configure your second wireless network (SSID2),
select Manual. If you are unable to configure the second wireless
network, contact your service provider for more information (these
settings may be controlled by your service provider).
Cisco WRP400 User Guide
-
Method #1: To configure a client device that has a Wi-Fi Protected
Setup button, click or press the Wi-Fi Protected Setup button on the
client device. Then click the button shown on the screen. After the client
device has been configured, click OK. Then refer to your client device or
its documentation for further instructions. Repeat for any additional
devices that you need to configure.
-
Method #2: To configure a client device that has a Wi-Fi Protected
Setup PIN number, enter the PIN number in the field on this screen. Click
Register. After the client device has been configured, click OK. Then
refer to your client device or its documentation for further instructions.
Repeat for any additional devices that you need to configure.
-
Method #3: If your client device asks for the PIN number of the WRP400,
enter the PIN number that is shown on the screen. This number also
appears on the label on the bottom of the WRP400. After the client
device has been configured, click OK. Then refer to your client device or
its documentation for further instructions. Repeat for any additional
devices that you need to configure.
54
Configuring Your Wireless Network
Wireless > Basic Wireless Settings
Cisco WRP400 User Guide
6
55
Configuring Your Wireless Network
Wireless > Wireless Security
6
Wireless > Wireless Security
You can use the Wireless Security page to configure the security of your wireless
network(s). The WRP400 supports the following wireless security mode options:
WPA Personal, WPA Enterprise, WPA2 Personal, WPA2 Enterprise, and WEP.
WEP (Wired Equivalent Privacy) is an older security standard. WPA (Wi-Fi
Protected Access) is a newer security standard that is stronger than WEP
encryption. A network encrypted with WPA/WPA2 is more secure than a network
encrypted with WEP, because WPA/WPA2 uses dynamic key encryption. To
protect the information as it passes over the airwaves, you should enable the
highest level of encryption supported by your network equipment.
These options are briefly discussed here. For additional guidelines, refer to
Chapter 2, “Before You Begin: Understanding Wireless Security.”
NOTE If you used Wi-Fi Protected Setup to configure your wireless network(s), then
wireless security has already been set up for your primary wireless network. Do
not make changes to the Wireless Security screen for your primary wireless
network.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Select the SSID that you want to configure. Then choose the Security Mode. If you
do not want to use wireless security, keep the default, Disabled.
Figure 25
Cisco WRP400 User Guide
Wireless > Wireless Security
56
Configuring Your Wireless Network
Wireless > Wireless Security
6
NOTE If you enabled the second wireless network on the Basic Wireless Settings screen,
you will need to set up wireless security for each SSID.
Depending on the selected Security Mode, additional fields appear.
WEP
WEP is a basic encryption method, which is not as secure as WPA
Figure 26
Cisco WRP400 User Guide
Wireless Security > WEP
•
Encryption: Select a level of WEP encryption, 64 bits 10 hex digits or 28
bits 26 hex digits. The default is 64 bits 10 hex digits.
•
Passphrase: Enter a Passphrase to automatically generate WEP keys. Then
click Generate.
•
Key 1-4: If you did not enter a Passphrase, enter the WEP key(s) manually.
•
TX Key: Select which TX (Transmit) Key to use. The default is 1.
57
Configuring Your Wireless Network
Wireless > Wireless Security
6
WPA Personal
Wi-Fi Protected Access (WPA) is a security mode that uses a shared key to restrict
access to authorized users.
NOTE If you are using WPA, always remember that each device in your wireless network
MUST use the same WPA method and shared key, or else the network will not
function properly.
Figure 27
Cisco WRP400 User Guide
Wireless Security > WPA Personal
•
WPA Algorithms: WPA supports two encryption methods, TKIP and AES,
with dynamic encryption keys. Select the type of algorithm, TKIP or AES.
The default is TKIP.
•
WPA Shared Key: Enter a WPA Shared Key of 8-63 characters.
•
Group Key Renewal: Enter a Group Key Renewal period, which instructs
the WRP400 how often it should change the encryption keys. The default is
3600 seconds.
58
Configuring Your Wireless Network
Wireless > Wireless Security
6
WPA2 Personal
Like WPA Personal, WPA2 Personal uses a shared key to restrict access to your
wireless network. WPA2 can combine TKIP and AES encryption.
Figure 28
Cisco WRP400 User Guide
Wireless Security > WPA2 Personal
•
WPA Algorithms: WPA2 supports two encryption methods, TKIP and AES,
with dynamic encryption keys. Select the type of algorithm, AES or TKIP +
AES. The default is TKIP + AES.
•
WPA Shared Key: Enter a WPA Shared Key of 8-63 characters.
•
Group Key Renewal: Enter a Group Key Renewal period, which instructs
the WRP400 how often it should change the encryption keys. The default is
3600 seconds.
59
Configuring Your Wireless Network
Wireless > Wireless Security
6
WPA Enterprise
This option features WPA used in coordination with a RADIUS (Remote
Authentication Dial-In User Service) server. This option should only be used when
a RADIUS server is connected to the WRP400.
Figure 29
Cisco WRP400 User Guide
Wireless Security > WPA Enterprise
•
WPA Algorithms: WPA supports two encryption methods, TKIP and AES,
with dynamic encryption keys. Select the type of algorithm, TKIP or AES.
The default is TKIP.
•
RADIUS Server Address: Enter the IP address of the RADIUS server.
•
RADIUS Port: Enter the port number of the RADIUS server. The default
value is 1812.
•
Shared Key: Enter the key shared between the WRP400 and the server.
•
Key Renewal Timeout: Enter a Key Renewal Timeout period, which
instructs the WRP400 how often it should change the encryption keys. The
default is 600 seconds.
60
Configuring Your Wireless Network
Wireless > Wireless Security
6
WPA2 Enterprise
This option features WPA2 used in coordination with a RADIUS (Remote
Authentication Dial-In User Service) server. This option should only be used when
a RADIUS server is connected to the WRP400.
Figure 30 Wireless > Wireless Security > WPA2Enterprise
Cisco WRP400 User Guide
•
WPA Algorithms: WPA2 supports two encryption methods, TKIP and AES,
with dynamic encryption keys. Select the type of algorithm, AES or TKIP +
AES. The default is TKIP + AES.
•
RADIUS Server Address: Enter the IP address of the RADIUS server.
•
RADIUS Port: Enter the port number of the RADIUS server. The default
value is 1812.
•
Shared Key: Enter the key shared between the WRP400 and the server.
•
Key Renewal Timeout: Enter a Key Renewal Timeout period, which
instructs the WRP400 how often it should change the encryption keys. The
default is 600 seconds.
61
6
Configuring Your Wireless Network
Wireless > Wireless MAC Filter
Wireless > Wireless MAC Filter
Wireless access can be filtered by using the MAC addresses of the wireless
devices within your network’s radius.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 31 Wireless > Wireless MAC Filter
•
Select a SSID: Select the SSID that you want to configure.
NOTE If you enabled the second wireless network on the Basic Wireless
Settings screen, then you can set up wireless MAC filtering for each
SSID.
Cisco WRP400 User Guide
62
Configuring Your Wireless Network
Wireless > Wireless MAC Filter
•
6
Wireless MAC Filter: To filter wireless users by MAC address, select
Enabled If you do not wish to filter users by MAC address, keep the default
setting, Disabled.
Access Restriction
In this section, you choose how to use the MAC Address Filter List: to prevent
access or to permit access.
•
Prevent: Select this option to block wireless access to devices with the
specified MAC addresses. This button is selected by default.
•
Permit: Select this to allow wireless access by devices with the specified
MAC addresses.
MAC Address Filter List
In this section, you identify the clients to filter. You can choose clients from the
Wireless Client List, or you can enter the MAC addresses individually.
•
Wireless Client List: Click this button if you want to choose the clients from
the Wireless Client List screen. See “Wireless Client List.” below.
•
MAC 01-40: Enter the MAC addresses of the devices whose wireless
access you want to block or allow.
Wireless Client List
Check the Save to MAC Address Filter List check box to select a device. Then
click Add to add the device to the MAC Address Filter List.
To retrieve the most up-to-date information, click Refresh. To exit this screen and
return to the Wireless MAC Filter screen, click Close.
Cisco WRP400 User Guide
63
Configuring Your Wireless Network
Wireless > Advanced Wireless Settings
Figure 32
6
Wireless Client List
Wireless > Advanced Wireless Settings
The Advanced Wireless Settings screen is used to set up the advanced wireless
functions of the WRP400. These settings should only be adjusted by an expert
administrator as incorrect settings can reduce wireless performance.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 33 Wireless > Advanced Wireless Settings
Cisco WRP400 User Guide
64
Configuring Your Wireless Network
Wireless > Advanced Wireless Settings
Cisco WRP400 User Guide
6
•
Authentication Type: The default is set to Auto, which allows either Open
System or Shared Key authentication to be used. With Open System
authentication, the sender and the recipient do not use a WEP key for
authentication. With Shared Key authentication, the sender and recipient
use a WEP key for authentication. Select Shared Key to only use Shared
Key authentication.
•
Transmission Rate: The rate of data transmission should be set depending
on the speed of your wireless network(s). You can select from a range of
transmission speeds, or you can select Auto to have the WRP400
automatically use the fastest possible data rate and enable the AutoFallback feature. Auto-Fallback will negotiate the best possible connection
speed between the WRP400 and a wireless client. The default is Auto.
•
CTS Protection Mode: The WRP400 will automatically use CTS (Clear-ToSend) Protection Mode when your Wireless-G products are experiencing
severe problems and are not able to transmit to the WRP400 in an
environment with heavy 802.11b traffic. This function boosts the ability of
the WRP400 to catch all Wireless-G transmissions but will severely
decrease performance. The default is Auto.
•
Beacon Interval: Enter a value between 1 and 65,535 milliseconds. The
Beacon Interval value indicates the frequency interval of the beacon. A
beacon is a packet broadcast by the WRP400 to synchronize the wireless
network(s). The default value is 100.
•
DTIM Interval: This value, between 1 and 255, indicates the interval of the
Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown
field informing clients of the next window for listening to broadcast and
multicast messages. When the WRP400 has buffered broadcast or
multicast messages for associated clients, it sends the next DTIM with a
DTIM Interval value. Its clients hear the beacons and awaken to receive the
broadcast and multicast messages. The default value is 1.
•
RTS Threshold: If you encounter inconsistent data flow, only minor
reduction of the default value, 2347, is recommended. If a network packet is
smaller than the preset RTS threshold size, the RTS/CTS mechanism will
not be enabled. The WRP400 sends Request to Send (RTS) frames to a
particular receiving station and negotiates the sending of a data frame.
After receiving an RTS, the wireless station responds with a Clear to Send
(CTS) frame to acknowledge the right to begin transmission. The RTS
Threshold value should remain at its default value of 2347.
65
7
Configuring Network Security and Controlling
Internet Access
You can use the Security screens to enable a firewall, add filters, or allow VPN
tunnels. You can use the Access Restrictions screen to control Internet usage.
?
How Do I...
•
Enable a firewall, Internet filters, or Web filters?
See “Security > Firewall,” on page 66
•
Allow VPN tunnels to pass through the firewall?
See “Security > VPN Passthrough,” on page 68
•
Block or allow specific types of Internet usage and
traffic?
See “Access Restrictions > Internet Access,” on
page 69.
Security > Firewall
The Firewall screen is used to configure a firewall that can filter out various types
of unwanted traffic on the local network.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Cisco WRP400 User Guide
66
Configuring Network Security and Controlling Internet Access
Security > Firewall
Figure 34
7
Security > Firewall
Firewall
•
SPI Firewall Protection: To use firewall protection, keep the default,
Enabled. To turn off firewall protection, select Disabled.
Internet Filter
Cisco WRP400 User Guide
•
Filter Anonymous Internet Requests: This feature makes it more difficult for
outside users to work their way into your network. This feature is selected
by default. Deselect the feature to allow anonymous Internet requests.
•
Filter Internet NAT Redirection: This feature uses port forwarding to block
access to local servers from local networked computers. Select this feature
to filter Internet NAT redirection. It is not selected by default.
•
Filter IDENT (Port 113): This feature keeps port 113 from being scanned
by devices outside of your local network. This feature is selected by
default. Deselect this feature to disable it.
67
Configuring Network Security and Controlling Internet Access
Security > VPN Passthrough
7
Web Filter
•
Proxy: Use of WAN proxy servers may compromise the security of the
WRP400. Denying Proxy will disable access to any WAN proxy servers.
Select this feature to enable proxy filtering. Deselect the feature to allow
proxy access.
•
Java: Java is a programming language for websites. If you deny Java, you
run the risk of not having access to Internet sites created using this
programming language. Select this feature to enable Java filtering. Deselect
the feature to allow Java usage.
•
ActiveX: ActiveX is a programming language for websites. If you deny
ActiveX, you run the risk of not having access to Internet sites created using
this programming language. Select this feature to enable ActiveX filtering.
Deselect the feature to allow ActiveX usage.
•
Cookies: A cookie is data stored on your computer and used by Internet
sites when you interact with them. Select this feature to filter cookies.
Deselect the feature to allow cookie usage.
Security > VPN Passthrough
The VPN Passthrough screen allows you to enable VPN tunnels using IPSec, PPTP,
or L2TP protocols to pass through the firewall of the WRP400.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 35
Cisco WRP400 User Guide
Security > VPN Passthrough
68
Configuring Network Security and Controlling Internet Access
Access Restrictions > Internet Access
7
•
IPSec Passthrough: Internet Protocol Security (IPSec) is a suite of protocols
used to implement secure exchange of packets at the IP layer. To allow IPSec
tunnels to pass through the WRP400, keep the default, Enabled.
•
PPTP: Passthrough Point-to-Point Tunneling Protocol (PPTP) allows the
Point-to-Point Protocol (PPP) to be tunneled through an IP network. To allow
PPTP tunnels to pass through the WRP400, keep the default, Enabled.
•
L2TP Passthrough: Layer 2 Tunneling Protocol is the method used to
enable Point-to-Point sessions via the Internet on the Layer 2 level. To allow
L2TP tunnels to pass through the WRP400, keep the default, Enabled.
Access Restrictions > Internet Access
You can use the Internet Access Policy screen to block or allow specific kinds of
Internet usage and traffic, such as Internet access, designated services, and
websites during specific days and times.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Cisco WRP400 User Guide
69
Configuring Network Security and Controlling Internet Access
Access Restrictions > Internet Access
Figure 36
•
Cisco WRP400 User Guide
7
Access Restrictions > Internet Access
Access Policy: Select a policy from the drop-down list to display that
policy’s settings. You can then enter or modify the settings. Be sure to save
your changes before selecting another policy from the drop-down list.
70
Configuring Network Security and Controlling Internet Access
Access Restrictions > Internet Access
Cisco WRP400 User Guide
7
•
Delete This Entry: To delete an access policy, select the policy’s number
from the Access Policy list, and then click this button.
•
Summary: To view all policies, click this button. The Summary appears in a
separate window. The policies are listed with the following information: No.
(number), Policy Name, Access, Days, Time of Day, and status (Enabled). To
enable a policy, check Enabled. To delete a policy, click Delete. Click Save
Settings to save your changes, or click Cancel Changes to cancel your
changes. To return to the Internet Access Policy screen, click Close.
•
Enter Policy Name: Enter a name for the policy that you selected in the
Access Policy list.
•
Status: Policies are disabled by default. To enable the selected policy,
select Enabled.
71
Configuring Network Security and Controlling Internet Access
Access Restrictions > Internet Access
•
7
Applied PCs: Click Edit List to select the computers that will be affected by
the policy that you selected in the Access Policy list. The List of PCs window
appears.
Choose the PCs that will be affected by this policy:
-
MAC Address: Enter a MAC address that you want to add to the list.
-
IP Address: Enter the final octet of an IP address that you want to add to
the list.
-
IP Address Range: Enter the final octet of an IP address in the first box,
and then enter the final octet of another IP address in the second box, to
create a range of IP addresses to add to the list.
Click Save Settings to save your changes, or click Cancel Changes to
cancel your changes. To return to the Internet Access Policy screen, click
Close.
•
Cisco WRP400 User Guide
Access Restriction: Select the appropriate option, Deny or Allow,
depending on whether you want to block or allow Internet access for the
computers that are listed on the List of PCs screen.
72
Configuring Network Security and Controlling Internet Access
Access Restrictions > Internet Access
7
•
Schedule: Decide which days and what times you want the selected policy
to be enforced. Select the individual days during which the policy will be in
effect, or select Everyday. Then enter a range of hours and minutes during
which the policy will be in effect, or select 24 Hours.
•
Website Blocking by URL Address: You can block websites with specific
URL addresses. Enter each URL in a separate URL field.
•
Website Blocking by Keyword: You can block websites using specific
keywords. Enter each keyword in a separate Keyword field.
•
Blocked Applications: You can filter access to various services accessed
over the Internet, such as FTP or telnet. You can block up to three
applications per policy.
-
From the Application list, select the application you want to block. Then
click the >> button to move it to the Blocked List. To remove an
application from the Blocked List, select it and click the << button.
-
If the application you want to block is not listed or you want to edit a
service’s settings, enter the application’s name in the Application Name
field. Enter its range in the Port Range fields. Select its protocol from the
Protocol drop-down menu. Then click Add.
-
To modify a service, select it from the Application list. Change its name,
port range, and/or protocol setting. Then click Modify.
-
To delete a service, select it from the Application list. Then click Delete.
Creating or Modifying an Internet Access Policy
Follow this procedure to create or modify an Internet Access Policy.
STEP 1
Select a number from the Access Policy drop-down menu.
STEP 2
Enter a name in the Policy Name field.
STEP 3
To enable this policy, select Enabled.
STEP 4
Click Edit List to select the computers that will be affected by this policy.
a. In the List of PCs window, enter individual MAC addresses or IP addresses, or
enter IP address ranges.
b. Click Save Settings to apply your changes, or click Cancel Changes to cancel
your changes. Then click Close close the window.
Cisco WRP400 User Guide
73
Configuring Network Security and Controlling Internet Access
Access Restrictions > Internet Access
7
STEP 5
In the Access Restriction section, choose to Deny Internet access or to Allow
Internet access for the computers that you listed on the List of PCs screen.
STEP 6
In the Schedule section, select the days and times when this policy applies, as
described above.
STEP 7
In the remaining sections of the page, enter the URLs, keywords, and applications
that you want to block with this policy, as described above.
STEP 8
Click Save Settings to save the settings. To cancel the settings, click Cancel
Changes.
STEP 9
Repeat these steps to create additional policies, one at a time.
Cisco WRP400 User Guide
74
8
Configuring Applications and Gaming
You can use the Applications and Gaming screens to configure your WRP400 to
support applications, services, and gaming.
?
Cisco WRP400 User Guide
How Do I...
•
Customize port services for common applications?
See “Applications and Gaming > Single Port
Forwarding,” on page 76.
•
Support public services such as web servers, FTP
servers, e-mail servers, and Internet gaming?
See “Applications and Gaming > Port Range
Forward,” on page 77.
•
Specify the ports that are opened for specific
applications?
See “Applications & Gaming > Port Range
Triggering,” on page 79.
•
Specify one computer to be exposed to the Internet
for public services?
See “Applications and Gaming > DMZ,” on page 80
•
Prioritize service for real-time applications such as
video-conferencing?
See “Applications and Gaming > QoS,” on page 81.
75
Configuring Applications and Gaming
Applications and Gaming > Single Port Forwarding
8
Applications and Gaming > Single Port Forwarding
The Single Port Forwarding screen allows you to customize port services for
common applications on this screen.
When users send these types of requests to your network via the Internet, the
WRP400 will forward those requests to the appropriate servers (computers).
Before using forwarding, you should assign static IP addresses to the designated
servers (use the DHCP Reservation feature on the Basic Setup screen). See
“DHCP Reservation,” on page 32.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 37 Applications and Gaming > Single Port Forwarding
Common applications are available for the first five entries. Select the appropriate
application. Then enter the IP address of the server that should receive these
requests. Select Enabled to activate this entry.
Cisco WRP400 User Guide
76
Configuring Applications and Gaming
Applications and Gaming > Port Range Forward
8
For additional applications, complete the following fields:
•
Application Name: Enter the name you wish to give the application. Each
name can be up to 12 characters.
•
External Port: Enter the external port number used by the server or Internet
application. Check with the Internet application documentation for more
information.
•
Internal Port: Enter the internal port number used by the server or Internet
application. Check with the Internet application documentation for more
information.
•
Protocol: Select the protocol used for this application, either TCP, UDP, or
oth.
•
To IP Address: For each application, enter the IP address of the PC that
should receive the requests. If you assigned a static IP address to the PC,
then you can click DHCP Reservation on the Basic Setup screen to look up
its static IP address.
•
Enabled: For each application, select Enabled to enable port forwarding.
Applications and Gaming > Port Range Forward
The Port Range Forward screen allows you to set up public services on your
network, such as web servers, ftp servers, e-mail servers, or other specialized
Internet applications. (Specialized Internet applications are any applications that
use Internet access to perform functions such as videoconferencing or online
gaming. Some Internet applications may not require any forwarding.)
When users send these types of requests to your network via the Internet, the
WRP400 will forward those requests to the appropriate servers (computers).
Before using forwarding, you should assign static IP addresses to the designated
servers (use the DHCP Reservation feature on the Basic Setup screen).
If you need to forward all ports to one computer, click the DMZ tab.
Cisco WRP400 User Guide
77
Configuring Applications and Gaming
Applications and Gaming > Port Range Forward
8
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 38
Applications and Gaming > Port Range Forwarding
To forward a port, enter the information on each line for the criteria required.
Cisco WRP400 User Guide
•
Application Name: In this field, enter the name you wish to give the
application. Each name can be up to 12 characters.
•
Start~End Port: Enter the number or range of port(s) used by the server or
Internet applications. Check with the Internet application documentation for
more information.
•
Protocol: Select the protocol used for this application, either TCP, UDP, or
oth.
•
To IP Address: For each application, enter the IP address of the PC running
the specific application. If you assigned a static IP address to the PC, then
you can click the DHCP Reservation button on the Basic Setup screen to
look up its static IP address. See “Setup > Basic Setup,” on page 23.
•
Enabled: Select Enabled to enable port forwarding for the applications you
have defined.
78
Configuring Applications and Gaming
Applications & Gaming > Port Range Triggering
8
Applications & Gaming > Port Range Triggering
The Port Range Triggering screen allows the WRP400 to watch outgoing data for
specific port numbers. The IP address of the computer that sends the matching
data is remembered by the WRP400, so that when the requested data returns
through the WRP400, the data is pulled back to the proper computer by way of IP
address and port mapping rules.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 39 Applications and Gaming > Port Range Triggering
Cisco WRP400 User Guide
•
Application Name: Enter the application name of the trigger.
•
Triggered Range: For each application, enter the starting and ending port
numbers of the triggered port number range. Check with the Internet
application documentation for the port number(s) needed.
•
Forwarded Range: For each application, enter the starting and ending port
numbers of the forwarded port number range. Check with the Internet
application documentation for the port number(s) needed.
•
Enabled: Select Enabled to enable port triggering for the applications you
have defined.
79
Configuring Applications and Gaming
Applications and Gaming > DMZ
8
Applications and Gaming > DMZ
The DMZ feature allows one network computer to be exposed to the Internet for
use of a special-purpose service such as Internet gaming or videoconferencing.
DMZ hosting forwards all the ports at the same time to one PC. The Port Range
Forwarding feature is more secure because it only opens the ports you want to
have opened, while DMZ hosting opens all the ports of one computer, exposing
the computer to the Internet.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 40
Applications and Gaming > DMZ
Any PC whose port is being forwarded must have its DHCP client function
disabled and should have a new static IP address assigned to it because its IP
address may change when using the DHCP function.
Cisco WRP400 User Guide
•
Enabled/Disabled: To disable DMZ hosting, select Disabled. To expose one
PC, select Enabled. Then configure the following settings:
•
Source IP Address: If you want any IP address to be the source, select Any
IP Address. If you want to specify an IP address or range of IP addresses as
the designated source, select and complete the IP address range fields.
80
Configuring Applications and Gaming
Applications and Gaming > QoS
8
•
Destination: If you want to specify the DMZ host by IP address, select IP
Address and enter the IP address in the field provided. If you want to
specify the DMZ host by MAC address, select MAC Address and enter the
MAC address in the field provided.
•
DHCP Client Table: Click this button to view a list of DHCP clients. See
“DHCP Client Table.” This button becomes available when you select the
MAC Address option.
DHCP Client Table
The DHCP Client Table lists computers and other devices that have been assigned
IP addresses by the WRP400. The list can be sorted by Client Name, IP Address,
and MAC Address. To select a DHCP client, click Select. To retrieve the most upto-date information, click Refresh. To exit this screen and return to the DMZ screen,
click Close.
Applications and Gaming > QoS
Quality of Service (QoS) ensures better service to high-priority types of network
traffic, which may involve demanding, real-time applications, such as
videoconferencing.
NOTE Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Cisco WRP400 User Guide
81
Configuring Applications and Gaming
Applications and Gaming > QoS
8
Figure 41 Applications and Gaming > QoS
Wireless
Cisco WRP400 User Guide
•
WMM Support: If you have other devices that support Wi-Fi Multimedia
(WMM) on your network, select Enabled. Otherwise, keep the default,
Disabled.
•
No Acknowledgement: To prevent the WRP400 from resending data if an
error occurs, select Enabled. Otherwise, keep the default, Disabled.
82
Configuring Applications and Gaming
Applications and Gaming > QoS
8
Internet Access Priority
In this section, you can set the bandwidth priority for a variety of applications and
devices. There are four levels priority: High, Medium, Normal, or Low. When you set
priority, do not set all applications to High, because this will defeat the purpose of
allocating the available bandwidth. If you want to select below normal bandwidth,
select Low. Depending on the application, a few attempts may be needed to set
the appropriate bandwidth priority.
•
Enabled/Disabled: To use the QoS policies you have set, keep the default,
Enabled. Otherwise, select Disabled.
•
Upstream Bandwidth: To allow the WRP400 to control the maximum
bandwidth for upstream data transmissions, keep the default, Auto. To
manually set the maximum, select Manual, and enter the appropriate
number in the field provided.
Category
There are four categories available. Select one of the following: Application, Online
Games, MAC Address, or Ethernet Port. Proceed to the instructions for your
selection.
Application
•
Application: Select the appropriate application. If you select Add a New
Application, follow the instructions for adding a new application.
•
Priority: Select the appropriate priority: High, Medium (Recommend),
Normal, or Low.
Adding a New Application
Cisco WRP400 User Guide
83
Configuring Applications and Gaming
Applications and Gaming > QoS
8
-
Enter a Name: Enter any name to indicate the name of the entry.
-
Port Range: Enter the port range in the text boxes, and choose a
protocol: TCP, UDP, or Both. You can have up to three ranges to define for
this bandwidth allocation. Port numbers can range from 1 to 65535.
Check your application’s documentation for details on the service ports
used.
-
Priority: Select the appropriate priority: High, Medium (Recommend),
Normal, or Low.
-
Click Add to save your changes. Your new entry will appear in the
Summary list.
Online Games
You can add an Online Game to the Summary list or change the Priority setting for
an existing game.
•
Game: Select the appropriate game. If you select Add a New Game, follow
the instructions for adding a new game.
•
Priority: Select the appropriate priority: High, Medium (Recommend),
Normal, or Low.
Adding a New Game
Cisco WRP400 User Guide
-
Enter a Name: Enter any name to indicate the name of the entry.
-
Port Range: Enter the port range in the text boxes, and choose a
protocol: TCP, UDP, or Both. For example, if you want to allocate
bandwidth for FTP, you can enter 21-21. If you need services for an
application that uses from 1000 to 1250, you enter 1000-1250 as your
settings. You can have up to three ranges to define for this bandwidth
allocation. Port numbers can range from 1 to 65535. Check your
application’s documentation for details on the service ports used.
-
Priority: Select the appropriate priority: High, Medium (Recommend),
Normal, or Low.
84
Configuring Applications and Gaming
Applications and Gaming > QoS
-
8
Click Add to save your changes. Your new entry will appear in the
Summary list.
MAC Address
•
Enter a Name: Enter a name for the device.
•
MAC Address: Enter the MAC address of the device.
•
Priority: Select the appropriate priority: High, Medium (Recommend),
Normal, or Low.
•
Add: Click this button to add your new entry to the Summary list.
Ethernet Port
Cisco WRP400 User Guide
•
Ethernet: Select the appropriate Ethernet port.
•
Priority: Select the appropriate priority: High, Medium (Recommend),
Normal, or Low.
•
Add: Click this button to add your new entry to the Summary list.
85
Configuring Applications and Gaming
Applications and Gaming > QoS
8
Summary
The Summary table lists the QoS entries that you have created for your
applications and devices.
Cisco WRP400 User Guide
•
Priority: This column displays the bandwidth priority of High, Medium,
Normal, or Low.
•
Name: This column displays the application, device, or port name.
•
Information: This column displays the port range or MAC address entered
for your entry. If a pre-configured application or game was selected, there
will be no valid entry shown in this section.
•
Remove: Click this button to remove an entry.
•
Edit: Click this button if you want to change the information. The information
will appear in the Category section of the page for editing.
86
9
Administration
You can use the Administration screens to manage access, configure Universal
Plug and Play, support multimedia streaming, enable logging and diagnostics,
restore factory default settings, upgrade firmware, and back up and restore
configurations.
?
Cisco WRP400 User Guide
How Do I...
•
Change the admin password?
See “Administration > Management,” on page 88.
•
Enable remote management of my network?
See “Administration > Management,” on page 88.
•
Configure UPnP (Universal Plug and Play)?
See “Administration > Management,” on page 88.
•
Enable support for multimedia streaming?
See “Administration > Management,” on page 88.
•
Enable and view logs?
“Administration > Log,” on page 91
•
Enable and view diagnostics?
“Administration > Diagnostics,” on page 93
•
Restore factory default settings?
“Administration > Factory Defaults,” on page 96
•
Upgrade the firmware?
See “Administration > Firmware Upgrade,” on
page 97.
•
Back up and restore settings?
See “Administration > Config Management,” on
page 99.
•
Reboot the device?
See “Administration > Reboot,” on page 100.
87
9
Administration
Administration > Management
Administration > Management
You can use the Administration > Management screen to change the password, to
manage access, to enable remote management, to configure UPnP (Universal Plug
and Play), and to enable support for multimedia streaming.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 42
Cisco WRP400 User Guide
Administration > Management
88
9
Administration
Administration > Management
Management
Router Access
Use this section of the page to enter a password to prevent unauthorized access
to the web-based utility, you will be asked for your password when you access
the web-based utility of the WRP400. The default is admin.
•
Router Password: Enter a new password for the WRP400.
•
Re-enter to Confirm: Enter the password again to confirm.
Web Access
•
Web Utility Access: HTTP (HyperText Transport Protocol) is the
communications protocol used to connect to servers on the World Wide
Web. HTTPS uses SSL (Secured Socket Layer) to encrypt data transmitted
for higher security. Select HTTP or HTTPS. HTTP is the default.
•
Web Utility Access via Wireless: If you are using the WRP400 in a public
domain where you are giving wireless access to your guests, you can
disable wireless access to the web-based utility of the WRP400. You will
only be able to access the utility via a wired connection if you disable the
setting. Keep the default, Enabled, to allow wireless access to the utility, or
select Disabled to block wireless access to the utility.
Remote Access
Cisco WRP400 User Guide
•
Remote Management: To permit remote access of the WRP400, from
outside the local network, select Enabled. Otherwise, keep the default,
Disabled.
•
Web Utility Access: HTTP (HyperText Transport Protocol) is the
communications protocol used to connect to servers on the World Wide
Web. HTTPS uses SSL (Secured Socket Layer) to encrypt data transmitted
for higher security. Select HTTP or HTTPS. HTTP is the default.
•
Remote Upgrade: If you want to be able to upgrade the WRP400 remotely,
from outside the local network, select Enabled. (You must have the Remote
Management feature enabled as well.) Otherwise, keep the default,
Disabled.
•
Allowed Remote IP Address: If you want to be able to access the WRP400
from any external IP address, select ny IP Address. If you want to specify an
external IP address or range of IP addresses, then select the second option
and complete the fields provided.
89
9
Administration
Administration > Management
•
Remote Management Port: Enter the port number that will be open to
outside access.
NOTE When you are in a remote location and wish to manage the WRP400, you can use
HTTP or HTTPS to connect to the IP address of the WRP400, at the remote
management port number, as shown:
http://<Internet_IP_address>:port or https://<Internet_IP_address>:port
•
<Internet_IP_address>: The Internet IP address of the WRP400
•
port: The Remote Management Port number
UPnP
Universal Plug and Play (UPnP) allows Windows XP and Vista to automatically
configure the WRP400 for various Internet applications, such as gaming and
videoconferencing.
•
UPnP: If you want to use UPnP, keep the default, Enabled. Otherwise, select
Disabled.
•
Allow Users to Configure: Keep the default, Enabled, if you want to be able
to make manual changes to the WRP400 while using the UPnP feature.
Otherwise, select Disabled.
•
Keep UPnP Configurations After System Reboot: If you enable the Allow
Users to Configure option, then this option will be available. Select Enabled,
if you want to keep UPnP configuration settings after the WRP400 reboots.
Otherwise, keep the default, Disabled.
•
Allow Users to Disable Internet Access: Select Enabled, if you want to be
able to prohibit any and all Internet connections. Otherwise, keep the
default, Disabled.
Multimedia Streaming
•
Cisco WRP400 User Guide
RTSP Support: If you experience issues with video-on-demand
applications, select Enabled to improve multimedia transmissions. Using
this option, the WRP400 will establish channels with the Real Time
Streaming Protocol) RTSP server, which is located at the service provider.
Otherwise, keep the default, Disabled.
90
9
Administration
Administration > Log
IGMP
Internet Group Multicast Protocol (IGMP) is used to establish membership in a
multicast group and is commonly used for multicast streaming applications. For
example, you may have Internet Protocol Television (IPTV) with multiple setup
boxes on the same local network. These setup boxes have different video streams
running simultaneously, so you should use the IGMP feature of the WRP400.
•
Support IGMP Version: Select the version you want to support, IGMP 1,
IGMP v2, or IGMP 3. If you are not sure which version to select, keep the
default, IGMP v2.
•
IGMP Proxy: Keep the default, Enabled, if you want to allow multicast traffic
through the WRP400 for your multimedia application devices. Otherwise,
select Disabled.
•
Immediate Leave: Select Enabled, if you use IPTV applications and want to
allow immediate channel swapping or flipping without lag or delays.
Otherwise, keep the default, Disabled.
Administration > Log
The WRP400 can keep logs of all traffic for your Internet connection.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 43
•
Cisco WRP400 User Guide
Administration > Log
Log: To disable the Log function, keep the default, Disabled. To monitor
traffic between the network and the Internet, select Enabled. With logging
enabled, you can choose to view temporary logs.
91
9
Administration
Administration > Log
•
View Log: To view the logs, click View Log.
Figure 44
Log > View Log
•
Type: Select Incoming Log, Outgoing Log, Security Log, or DHCP Client
Log.
•
The Incoming Log will display a temporary log of the source IP addresses
and destination port numbers for the incoming Internet traffic.
•
The Outgoing Log will display a temporary log of the local IP addresses,
destination URLs/IP addresses, and service/port numbers for the outgoing
Internet traffic.
•
The Security Log will display the login information for the web-based
utility.
•
The DHCP Client Log will display the LAN DHCP server status information.
Click Refresh to update the log. Click Clear to clear all the information that is
displayed.
Cisco WRP400 User Guide
92
9
Administration
Administration > Diagnostics
Administration > Diagnostics
The diagnostic tests (Ping, Traceroute, and Detect Active LAN Clients) allow you to
check the connections of your network devices, including connection to the
Internet.
Figure 45
Administration > Diagnostics
Ping Test
The Ping test checks the status of a connection.
Cisco WRP400 User Guide
•
IP or URL Address: Enter the address of the PC whose connection you
wish to test.
•
Packet Size: Enter the packet size you want to use. The default is 32 bytes.
•
Times to Ping: Enter many times you wish to test it.
•
Start to Ping: To run the test, click this button. The Ping Test screen will
show if the test was successful. Click Close to return to the Diagnostics
screen.
93
9
Administration
Administration > Diagnostics
Figure 46
Diagnostics > Ping
Traceroute Test
The Traceroute test tests the performance of a connection.
Cisco WRP400 User Guide
•
IP or URL Address: Enter the address of the PC whose connection you
wish to test.
•
Start to Traceroute: To run the test, click this button. The Traceroute Test
screen will show if the test was successful. Click Close to return to the
Diagnostics screen.
94
9
Administration
Administration > Diagnostics
Figure 47 Diagnostics > Traceroute
Detect Active LAN Client(s)
•
Search Time: Select how many seconds you wish to perform this search: 5,
0, or 15.
•
Start to Search: To run the search, click this button. The Active LAN Client
Table screen will show the search results. You can sort the results by IP
Address, MAC Address, Interface, Client Name, or IP Status.
To re-run the search, click Retry. Click Close to return to the Diagnostics screen.
Cisco WRP400 User Guide
95
9
Administration
Administration > Factory Defaults
Figure 48
Diagnostics > Active LAN Client Table
Administration > Factory Defaults
The Administration > Factory Defaults screen allows you to restore the default
configuration to the router settings and/or voice settings.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 49 Administration > Factory Defaults
NOTE Restoring factory defaults deletes custom settings. Note your custom settings
before restoring the factory defaults.
•
Cisco WRP400 User Guide
Restore Router Factory Defaults: To reset the router settings to the default
values, select Yes. Then click Save Settings. Any custom router settings you
have saved will be lost when the default settings are restored.
96
9
Administration
Administration > Firmware Upgrade
•
Restore Voice Factory Defaults: To reset the voice settings to the default
values, select Yes. Then click Save Settings. Any custom Voice settings you
have saved will be lost when the default settings are restored.
NOTE Restoring the voice defaults may require your login (the default user name and
password are admin). If the defaults do not work, contact your service provider for
more information.
Administration > Firmware Upgrade
The Firmware Upgrade screen allows you to upgrade the firmware of the
WRP400. Do not upgrade the firmware unless you are experiencing problems with
the WRP400 or the new firmware has a feature you want to use.
If you want to upgrade the firmware, then you may need a user name and
password available only from your service provider. Contact your service provider
for more information.
Username & Password
If you see the Username & Password screen, enter the User Name and Password
provided by your service provider. (The factory default User Name and Password
are admin.) Then click OK.
Figure 50
Cisco WRP400 User Guide
Administration > Username & Password
97
9
Administration
Administration > Firmware Upgrade
NOTE The WRP400 may lose the settings you have customized. Before you upgrade the
firmware, use the Config Management screen to back up your settings. For more
informaiton, see “Administration > Config Management,” on page 99.
Firmware Upgrade
Download the latest firmware from Cisco.com, and then upgrade the firmware on
your WRP400.
Downloading the Firmware
STEP 1
Go to the WRP400 product page on Cisco.com:
http://www.cisco.com/en/US/products/ps10028/index.html
NOTE This site requires a login. If you do not have a user account, you can register
for free.
STEP 2
Click the Download Software link.
STEP 3
When the Download Software page appears, click the link under the Latest
Releases folder.
STEP 4
On the right side of the page, click the link for the BIN file.
STEP 5
When the Download Image page appears, click Download.
STEP 6
Read the license agreement, and then click Agree at the end of the page.
STEP 7
When the File Download window appears, click Save, and then save the file in the
desired location, such as your Windows Desktop.
STEP 8
When the Download Complete window appears, click Close.
Cisco WRP400 User Guide
98
9
Administration
Administration > Config Management
Firmware Upgrade
After you download the firmware from Cisco.com, you can upgrade the WRP400.
Figure 51 Administration > Firmware Upgrade
•
Please select a file to upgrade the firmware: Click Browse and select the
firmware upgrade file that you downloaded from Cisco.com.
•
Start to Upgrade: After you have selected the appropriate file, click this
button, and follow the on-screen instructions.
Administration > Config Management
The Config Management screen allows you to back up or restore the settings by
using a configuration file.
Figure 52
Cisco WRP400 User Guide
Administration > Config Management
99
9
Administration
Administration > Reboot
Backup Configuration
•
Backup: To save the settings in a configuration file, click this button and
follow the on-screen instructions.
Restore Configuration
To use this option, you must have previously backed up its configuration settings.
•
Please select a file to restore: Click the Browse button and select the
configuration file.
•
Restore: To restore the configuration settings, click this button and follow
the on-screen instructions.
Administration > Reboot
The Reboot screen allows you to reboot the device from the administration web
server. Click the Reboot button.
Figure 53
Cisco WRP400 User Guide
Administration > Config Management
100
10
Using the Status Screens
You can use the Status screens to view information about your WRP400.
?
Cisco WRP400 User Guide
How Do I...
•
View the firmware version, the router name, the host
name, the Internet MAC address and the current
time?
See “Status > Router,” on page 102.
•
View the status of the Internet connection?
See “Internet Connection,” on page 103.
•
View the status and basic information about my
mobile network?
See “Status > Mobile Network,” on page 104
•
View information about my local wired network?
See “Status > Local Network,” on page 106.
•
View information about the DHCP server and DHCP
Table?
See “Status > Local Network,” on page 106
•
View information about my wireless network?
See “Status > Wireless Network,” on page 108.
101
10
Using the Status Screens
Status > Router
Status > Router
The Router screen displays information about the WRP400.
Figure 54
Status > Router
Router Information
Cisco WRP400 User Guide
•
Firmware Version: The version number of the current firmware is
displayed.
•
Current Time: The time set on the WRP400 is displayed.
102
10
Using the Status Screens
Status > Router
•
Internet MAC Address: The MAC address, as seen by your service
provider, is displayed.
•
Router Name: The name of the WRP400 is displayed.
•
Host Name: If required by your service provider, this was entered on the
Basic Setup screen.
•
Domain Name: If required by your service provider, this was entered on the
Basic Setup screen.
Internet Connection
This section shows the current network information. It varies depending on the
Internet connection type selected on the Basic Setup screen.
Click Refresh to update the on-screen information.
Cisco WRP400 User Guide
103
10
Using the Status Screens
Status > Mobile Network
Status > Mobile Network
The Mobile Network Status screen shows the status of the mobile network and
displays information about the data card. The screen automatically refreshes
periodically.
Figure 55 Status > Mobile Network Status
Mobile Network Status
Cisco WRP400 User Guide
•
Connection: The status of the mobile network connection, either
Disconnected or Connected
•
Connection Up Time: The period of time that the Mobile USB modem has
been connected to the Internet during this session
•
Current Session Usage: The number of packets have been downloaded
and uploaded during this session
104
10
Using the Status Screens
Status > Mobile Network
Data Card Status
Cisco WRP400 User Guide
•
Manufacturer: The manufacturer of the Mobile USB modem data card
•
Card Model: The model number of your Mobile USB modem data card
•
Card Firmware: The firmware that is installed on your Mobile USB modem
data card
•
SIM Status: The status of your SIM card
•
IMSI: International Mobile Subscriber Identity is a unique number that is
stored in the Subscriber Identity Module (SIM) associated with all GSM and
Universal Mobile Telecommunications System (UMTS) network mobile
phone users
•
Carrier: The network service provider that is used for Internet connection
•
Service Type: Displayed your current UMTS/GPRS/EVDO service for
Internet connection.
•
Signal Strength: Indicated the signal strength of your current UMTS/GPRS/
EVDO service to your location.
•
Card Status: Indicated current Mobile WAN connection status.
105
10
Using the Status Screens
Status > Local Network
Status > Local Network
The Local Network screen displays information about the local, wired network.
Figure 56
Status > Local Network
Local Network
•
Local MAC Address: The MAC address of the local, wired interface of the
WRP400 is displayed.
•
Router IP Address: The IP address of the WRP400, as it appears on your
local network, is displayed.
•
Subnet Mask: The Subnet Mask of the WRP400 is displayed.
DHCP Server
Cisco WRP400 User Guide
•
DHCP Server: The status of the DHCP server function is displayed.
•
Start IP Address: For the range of IP addresses used by devices on your
local network, the starting IP address is displayed.
•
End IP Address: For the range of IP addresses used by devices on your
local network, the ending IP address is displayed.
•
DHCP Clients Table: Click this button to view a list of computers that are
using the WRP400 as a DHCP server.
106
Using the Status Screens
Status > Local Network
10
Figure 57 DHCP Clients Table
DHCP Client Table
The DHCP Client Table lists computers and other devices that have been assigned
IP addresses by the WRP400. The list can be sorted by Client Name, IP Address,
Interface, MAC Address, and Expires Time (how much time is left for the current IP
address). To remove a DHCP client, click Delete. To retrieve the most up-to-date
information, click Refresh. To exit this screen and return to the Local Network
screen, click Close.
Cisco WRP400 User Guide
107
10
Using the Status Screens
Status > Wireless Network
Status > Wireless Network
The Wireless Network screen displays information about your wireless network(s).
Figure 58
Status > Wireless Network
•
Channel: The channel of the wireless network(s) is displayed.
•
Mode: The wireless mode is displayed.
Status information for each wireless network is displayed.
Cisco WRP400 User Guide
•
Wireless MAC Address: The wireless MAC address of the local, wireless
interface is displayed.
•
Network Name (SSID): The network name, which is also called the SSID, is
displayed.
•
Security: The wireless security method is displayed.
•
SSID Broadcast: The status of the SSID Broadcast feature is displayed.
108
11
Configuring Voice Services
You can use the Voice screens to manage the voice gateway features of the
WRP400.
?
How Do I...
•
View the Voice screens?
See “Access to the Voice Screens,” on page 109
•
View product information, system status, and line
status?
See “Voice > Info,” on page 110
•
Change the password for user access to the Voice
screens?
See “Voice > System,” on page 113
•
Set call forwarding, speed dial, supplementary
services, and ring settings?
See “Voice > User 1/2,” on page 114
•
Configure the Admin login?
See “Voice > Admin Login,” on page 118
Access to the Voice Screens
There are two level of access, user and Admin Login. When you click the Voice
tab, the Info screen is automatically displayed. If you set a User Password on the
System screen, then you will be asked to enter it before the Info screen is
displayed.
The Admin Login allows access to more advanced settings. To access
administrative screens, click Admin Login, and enter the user name and password
provided by your service provider. Contact your service provider for more
information. (The factory default Admin Login name and password are admin.)
Cisco WRP400 User Guide
109
Configuring Voice Services
Voice > Info
11
NOTE In most cases, you do not need to use the administrative screens. Contact your
service provider for more information.
Voice > Info
The Info screen displays Voice over Internet Protocol (VoIP) information about the
WRP400.
Figure 59 Voice > Info
Cisco WRP400 User Guide
110
11
Configuring Voice Services
Voice > Info
Product Information
•
Product Name: The model number of the WRP400
•
Serial Number: The serial number of the WRP400
•
Software Version: The version number of the WRP400 software
•
Hardware Version: The version number of the WRP400 hardware
•
MAC Address: The MAC address of the WRP400
•
Client Certificate: The status of the client certificate, which indicates that
the WRP400 has been authorized by your service provider,
System Status
Cisco WRP400 User Guide
•
Current Time: The current date and time of the WRP400 are displayed.
•
Elapsed Time: The amount of time elapsed since the last reboot of the
WRP400
•
RTP Packets Sent: The number of RTP packets sent by the WRP400
•
RTP Bytes Sent: The number of RTP bytes sent by the WRP400
•
RTP Packets Recv: The number of RTP packets received by the WRP400
•
RTP Bytes Recv: The number of RTP bytes received by the WRP400
•
SIP Messages Sent: The number of SIP messages sent by the WRP400
•
SIP Bytes Sent: The number of SIP bytes sent by the WRP400
•
SIP Messages Recv: The number of SIP messages received by the
WRP400
•
SIP Bytes Recv: The number of SIP bytes received by the WRP400
•
External IP: The external IP address used for NAT mapping
111
11
Configuring Voice Services
Voice > Info
Line 1/2 Status
Lines 1 and 2 have the same status information available.
•
Hook State: The status of the Internet phone line’s readiness. “On” indicates
that it is ready for use, while “Off” indicates that it is in use.
•
Registration State: The status of the line’s registration with the service
provider
•
Last Registration At: The last date and time the line was registered are
displayed.
•
Next Registration In: The number of seconds until the next registration
•
Message Waiting: This indicates whether you have new voicemail waiting.
•
Call Back Active: This indicates whether a call back request is in progress.
•
Last Called Number: The last number called
•
Last Caller Number: The number of the last caller
•
Mapped SIP Port: The port number of the NAT mapped SIP port
Calls 1 and 2 have the same status information available.
Cisco WRP400 User Guide
•
Call 1/2 State: The status of the call
•
Call 1/2 Tone: The type of tone used by the call
•
Call 1/2 Encoder: The codec used for encoding
•
Call 1/2 Decoder: The codec used for decoding
•
Call 1/2 FAX: The status of the fax pass-through mode
•
Call 1/2 Type: The direction of the call
•
Call 1/2 Remote Hold: This indicates whether the far end has placed the
call on hold.
•
Call 1/2 Callback: This indicates whether the call was triggered by a call
back request.
•
Call 1/2 Peer Name: The name of the internal phone
•
Call 1/2 Peer Phone: The phone number of the internal phone
•
Call 1/2 Duration: The duration of the call
112
11
Configuring Voice Services
Voice > System
•
Call 1/2 Packets Sent: The number of packets sent
•
Call 1/2 Packets Recv: The number of packets received
•
Call 1/2 Bytes Sent: The number of bytes sent
•
Call 1/2 Bytes Recv: The number of bytes received
•
Call 1/2 Decode Latency: The number of milliseconds for decoder latency
•
Call 1/2 Jitter: The number of milliseconds for receiver jitter
•
Call 1/2 Round Trip Delay: The number of milliseconds for delay
•
Call 1/2 Packets Lost: The number of packets lost
•
Call 1/2 Packet Error: The number of invalid packets received
•
Call 1/2 Mapped RTP Port: The number of the NAT mapped RTP port
•
Call 1/2 Media Loopback: The Media Loopback feature allows the service
provider to test the quality of the connection to the WRP400. The status of
the feature
Voice > System
The System screen displays the User Password setting.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Figure 60
Cisco WRP400 User Guide
Voice > System
113
11
Configuring Voice Services
Voice > User 1/2
System Configuration
•
User Password: Enter the password for user access to the Voice screens.
(By default, there is no password.)
Miscellaneous Settings
No settings are displayed.
Voice > User 1/2
The User 1 and 2 screens display similar settings. The User 1 screen displays
settings for users of phone line 1, and the User 2 screen displays settings for users
of phone line 2.
NOTE After you enter settings on this page, click Save Settings to apply your changes, or
click Cancel Changes to cancel your changes.
Cisco WRP400 User Guide
114
Configuring Voice Services
Voice > User 1/2
11
Figure 61 Voice > User 1
Cisco WRP400 User Guide
115
11
Configuring Voice Services
Voice > User 1/2
Call Forward Settings
Enter the call forwarding numbers you want to use.
•
Cfwd All Dest: Enter the number for the Call Forward All Service feature
(when you want to forward all calls).
•
Cfwd Busy Dest: Enter the number for the Call Forward Busy feature (when
the line is busy).
•
Cfwd No Ans Dest: Enter the number for the Call Forward No Answer
feature (when the line is not answered).
•
Cfwd No Ans Delay: Enter the number of seconds to wait before the Call
Forward No Answer feature is triggered. The default is 20.
Selective Call Forward Settings
Enter the caller numbers that will be forwarded to specific phone numbers.
•
Cfwd Sel1-8 Caller: Enter the caller number pattern to trigger the Call
Forward Selective (1-8) feature.
•
Cfwd Sel1-8 Dest: Enter the forward number for the Call Forward Selective
(1-8) feature.
•
Cfwd Last Caller: Enter the caller number that is actively forwarded to the
Cfwd Last Dest number when the Call Forward Last activation code is used.
•
Cfwd Last Dest: Enter the forward number for the Cfwd Last Caller feature.
•
Block Last Caller: Enter the ID of the caller blocked via the Block Last Caller
service.
•
Accept Last Caller: Enter the ID of the caller accepted via the Accept Last
Caller service.
Speed Dial Settings
•
Cisco WRP400 User Guide
Speed Dial 2-9: Enter the phone number for each Speed Dial setting.
116
11
Configuring Voice Services
Voice > User 1/2
Supplementary Service Settings
•
CW Setting: Select whether you want to use the Call Waiting feature for all
calls, yes or no. The default is yes.
•
Block CID Setting: Select whether you want to block Caller ID for all calls,
yes or no. The default is no.
•
Block ANC Setting: Select whether you want to block anonymous calls,
yes or no. The default is no.
•
DND Setting: Select whether you want to use the Do Not Disturb (DND)
feature, Yes or no. The default is no.
•
CID Setting: Select whether you want to enable Caller ID generation, yes or
no. The default is yes.
•
CWCID Setting: Select whether you want to enable Caller ID for Call
Waiting, yes or no. The default is yes.
•
Dist Ring Setting: Select whether you want to use the Distinctive Ring
feature, Yes or no. The default is yes.
•
Message Waiting: Select whether you want to use the Message Waiting
feature, yes or no. The default is no.
Distinctive Ring Settings
•
Ring1-8 Caller: Enter the caller number pattern to play Distinctive Ring/Call
Waiting Tone (1-8).
Ring Settings
Cisco WRP400 User Guide
•
Default Ring: Select the default ringing pattern for all callers. The default is
1.
•
Default CWT: Select the default CWT pattern for all callers. The default is 1.
•
Hold Reminder Ring: Select the ring pattern that will remind you of a call on
hold when the phone is on-hook. The default is 8.
•
Call Back Ring: Select the ring pattern for call back notification. The default
is 7.
•
Cfwd Ring Splash Len: Enter the duration of the ring splash when a call is
forwarded. The range is 0 to 10.0 seconds. The default is 0.
117
11
Configuring Voice Services
Voice > Admin Login
•
Cblk Ring Splash Len: Enter the duration of the ring splash when a call is
blocked. The range is 0 to 10.0 seconds. The default is 0.
•
VMWI Ring Splash Len: Enter the duration of the ring splash when new
messages arrive before the VoiceMail Waiting Indication (VMWI) signal is
applied. The range is 0 to 10.0 seconds. The default is 0.
Click Save Settings to apply your changes, or click Cancel Changes to cancel your
changes.
Voice > Admin Login
The Admin Login allows access to more advanced settings. To access
administrative screens, click Admin Login, and enter the user name and password
provided by your service provider. Contact your service provider for more
information. (The factory default Admin Login name and password are admin.)
NOTE In most cases, you do not need to use the administrative screens. Contact your
service provider for more information.
Cisco WRP400 User Guide
118
12
Interactive Voice Response Menu
Overview
This chapter explains how to use the Interactive Voice Response (IVR) Menu to
configure the network settings. Use your telephone’s keypad to enter your
commands and select choices, and the WRP400 will use voice responses.
To access the IVR Menu:
STEP 1
Use a telephone connected to the Phone 1 or 2 port of the WRP400. (You can only
access the IVR Menu through an analog telephone, not any of the Internet phones.)
STEP 2
Press **** (in other words, press the star key four times).
STEP 3
Wait until you hear the response, “Configuration menu. Please enter the option
followed by the # (pound) key, or hang up to exit”.
Menu Commands
Refer to the following table that lists actions, commands, menu choices, and
descriptions. After you select an option, press the # (pound) key. To exit the menu,
hang up the telephone.
If the menu is inactive for more than one minute, the WRP400 will time out. To reenter the menu, press ****.
Cisco WRP400 User Guide
119
12
Interactive Voice Response Menu
Menu Commands
Action
Command
Enter IVR Menu
****
Use this command to enter
the IVR Menu. Ignore
Special Information Tones
(SITs) or other tones until
you hear, “Configuration
menu. Please enter the
option followed by the #
(pound) key, or hang up to
exit.”
Check DHCP
100
The IVR announces
whether DHCP is enabled
or disabled.
Check IP
Address
110
The IVR announces the
current IP address of the
WRP400.
Check Subnet
Mask
120
The IVR announces the
current subnet mask of the
WRP400.
Check Static
Gateway IP
Address
130
The IVR announces the
current gateway IP
address of the WRP400.
Check MAC
Address
140
The IVR announces the
MAC address of the
WRP400 in hexadecimal
string format.
Check Firmware
Version
150
The IVR announces the
version number of the
firmware running on the
WRP400.
Voice Factory
Reset of the
Router
73738
Warning: All
custom settings
will be lost.
Cisco WRP400 User Guide
Choices
Confirm Press 1.
Cancel Press *
(star).
Description
After the WRP400
requests confirmation,
press 1 to confirm.
After you hear, “Option
successful”, hang up the
phone. All voice settings
will be reset to their
defaults.
120
A
Troubleshooting
NOTE If your questions are not addressed here, refer to the Application Notes and other
Technical Resources on Cisco Partner Central website for Voice and Conferencing,
at the following URL:
http://www.cisco.com/web/partners/sell/smb/products/
voice_and_conferencing.html
This chapter has two sections:
•
“General Troubleshooting,” on page 121
•
“Mobile Network Troubleshooting,” on page 125
General Troubleshooting
Q.
My computer cannot connect to the Internet.
Follow these instructions until your computer can connect to the Internet:
a. Make sure that the WRP400 is powered on. The Power LED should be
green and not flashing.
b. If the Power LED is flashing, then power off all of your network devices,
including the modem, the WRP400, and the computers. Wait 30 seconds.
Then power on each device in the following order:
-
Cable or DSL modem
-
WRP400
-
Computer
c. Check the cable connections. The computer should be connected to one
of the ports numbered 1-4 on the WRP400, and the modem must be
connected to the Internet port on the WRP400.
Cisco WRP400 User Guide
121
A
Troubleshooting
Q.
There is no dial tone, and the Phone 1 or 2 LED is not lit.
Follow these instructions until your problem is solved:
a. Make sure the telephone is plugged into the appropriate port, Phone 1 or
2.
b. Disconnect and re-connect the RJ-11 telephone cable between the
WRP400 and telephone.
c. Make sure your telephone is set to its tone setting (not pulse).
d. Make sure your network has an active Internet connection. Try to access
the Internet, and check to see if the WRP400 Internet LED is lit. If you do
not have a connection, then power off all of your network devices,
including the modem, the WRP400, and the computers. Wait 30 seconds.
Then power on each device in the following order:
-
Cable or DSL modem
-
WRP400
-
Computers and other devices
e. Verify your account information and confirm that the phone line is
registered with your Internet Telephony Service Provider (ITSP).
Q.
When I place an Internet phone call, words are dropped intermittently.
Consider the following possible causes and solutions:
Cisco WRP400 User Guide
-
Cordless phone: If you are using the WRP400 wireless function and a
cordless phone, they may be using the same frequency and may
interfere with each other. Move the cordless phone farther away from
the WRP400.
-
Network activity: There may be heavy network activity, particularly if
you are running a server or using a file sharing program. Try to limit
network or Internet activity during Internet phone calls. For example, if
you are running a file sharing program, files may be uploaded in the
background even though you are not downloading any files, so make
sure you exit the program before making Internet phone calls.
-
Bandwidth: There may not be enough bandwidth available for your
Internet phone call. You may want to test your bandwidth by using one of
the bandwidth tests available online. If necessary, access your Internet
phone service account and reduce the bandwidth requirements for your
service. For more information, refer to the website of your ITSP.
122
A
Troubleshooting
Q.
The modem does not have an Ethernet port.
If your modem does not have an Ethernet port, then it is a modem for
traditional dial-up service. To use the WRP400, you need a cable/DSL
modem and a high-speed Internet connection.
Q.
I cannot use the DSL service to connect manually to the Internet.
After you have installed the WRP400, it will automatically connect to your
Internet Service Provider (ISP) or Internet Telephony Service Provider
(ITSP), so you no longer need to connect manually.
Q.
The DSL telephone line does not fit into the WRP400 Internet port.
The WRP400 does not replace your modem. You still need your DSL
modem in order to use the WRP400. Connect the telephone line to the DSL
modem, insert the setup CD into your computer, and then follow the
on-screen instructions.
Q.
When I double-click the web browser, I am prompted for a username
and password. How can I bypass this prompt?
Launch the web browser and perform the following steps (these steps are
specific to Internet Explorer but are similar for other browsers):
a. Select Tools > Internet Options.
b. Click the Connections tab.
c. Select Never dial a connection.
d. Click OK.
Q.
The WRP400 does not have a coaxial port for the cable connection.
The WRP400 does not replace your modem. You still need your cable
modem in order to use the WRP400. Connect your cable connection to the
cable modem, insert the setup CD into your computer, and then follow the
on-screen instructions.
Q.
The computer cannot connect wirelessly to the network.
Make sure the wireless network name or SSID is the same on both the
computer and the WRP400. If you have enabled wireless security, then
make sure the same security method and key are used by both the
computer and the WRP400.
Cisco WRP400 User Guide
123
A
Troubleshooting
Q.
I need to modify the settings on the WRP400.
To access the web-based utility, follow these instructions:
a. Launch the web browser on your computer, and enter the default IP
address of the WRP400, 192.168.15.1, in the Address field. Then press
Enter.
NOTE If you place the WRP400 behind a primary router with the IP address
of 192.168.15.1, then the WRP400 will automatically assume a new
default IP address, 192.168.16.1.
b. A login screen appears. The first time you open the web-based utility,
use the default user name and password, admin. (You can set a new
password from the Administration tab’s Management screen.) Then click
OK.
c. Click the appropriate tab to change the settings.
Q.
I cannot configure the settings for the second wireless network
because the SSID2 settings are grayed out.
Your service provider may control the settings for the second wireless
network (SSID2). Contact your service provider for more information.
Q.
I upgraded my firmware and now the WRP400 is not working properly.
If the WRP400 is not working properly after an upgrade, you may need to
perform a factory reset. There are two ways to perform a factory reset.
-
Option 1: Press and hold the reset button located on the side panel for
approximately ten seconds.
-
Option 2: Access the web-based utility and browse to Administration >
Factory Defaults. Select Yes to reset the WRP400 settings to the
default values.
NOTE Service Providers: If version 2.0 or higher is installed, and you want to
downgrade a device to version 1.0, first downgrade to version 1.01.00.
Then downgrade to version 1.0. This interim firmware is designed to
ensure that the version 2.0 settings are reconfigured for version 1.0.
Cisco WRP400 User Guide
124
A
Troubleshooting
Mobile Network Troubleshooting
Q.
What do I do if the WRP400 does not recognize my USB device?
a. Make sure that you have the latest mobile-support firmware loaded on
your WRP400. To download the latest firmware, go to the WRP400
product page on www.cisco.com/en/US/products/ps10028/index.html
b. Make sure that your USB device is on the list of supported Mobile
Broadband USB Modems. For more information, visit the WRP400
product page on www.cisco.com/en/US/products/ps10028/index.html
c. If you're installing a Mobile Broadband USB modem, make sure that your
modem is activated with a data service, and verify that it can be used on
your computer.
Q.
The Power LED is continuously flashing green and orange. What does it
mean?
When you plug in a USB device, the Power LED indicates the progress of
initialization. After successful initialization, the Power LED shines steady
green.
If the device fails to initialize, the LED continues to flash green and orange. In
this case, check to make sure that you have the latest firmware, that your
USB device is supported, and that your modem is activated with a data
service, as described above.
Q.
My WRP400's Power LED continuous flashing orange. What does it
mean?
When a USB modem is installed, the Power LED indicates the status of the
mobile network connection. Continuous flashing orange means the router
failed to connect to the Internet through the mobile network connection and
is trying again. One possible explanation is that the router cannot get a
strong signal from the mobile network. Consider moving the router to a
location where you have a stronger signal. The Power LED shines steady
orange upon a successful mobile network connection,
Q.
Q. I am unable to connect to the mobile network. What do I do?
a. Make sure that you have the latest mobile-support firmware loaded on
your WRP400. To download the latest firmware, go to the WRP400
product page on www.cisco.com/en/US/products/ps10028/index.html
Cisco WRP400 User Guide
125
A
Troubleshooting
b. Make sure that your USB device is on the list of supported Mobile
Broadband USB Modems. For more information, visit the WRP400
product page on www.cisco.com/en/US/products/ps10028/index.html
c. If you're installing a Mobile Broadband USB modem, make sure that your
modem is activated with a data service, and verify that it can be used on
your computer.
d. Some mobile network service providers require that you enter specific
information such as APN, Dial Number, User Name, and Password. This
information can be obtained from your service provider, if required. Log
on to the WRP400 administration web server and input the correct
settings on the Setup > Mobile Network page, the Mobile Network Setup
section.
e. Make sure that you input the correct SIM PIN if you lock your SIM with a
PIN code.
Q.
How do I disconnect from the mobile broadband network, when not in
use?
Disconnecting from your mobile broadband service when not in use may
provide savings on usage costs or prevent unnecessary downloads. To
disconnect, you can use one of the following methods:
-
Option 1: Physically remove and reinsert your Mobile Broadband USB
modem from the WRP400.
-
Option 2: Log on to the WRP400 web-based utility. Click Setup tab >
Mobile Network page. Click the Disconnect button.
NOTE The Disconnect button appears only when Connect mode is set on
Manual. For more information, see “Setup > Connection Recovery,”
on page 46.
Q.
Why does my WRP400 always use my Ethernet connection instead of
my mobile network connection?
By default, the WRP400 connects to the Internet through the Ethernet
interface, if available. The mobile network connection may be used as a
failover when an Ethernet connection is unavailable. If you wish to connect
to mobile network only, simply unplug your Ethernet cable. Alternatively,
change the Priority setting so that the mobile network connection is used
even when the Ethernet cable is connected. To change these settings, log
Cisco WRP400 User Guide
126
A
Troubleshooting
on to the WRP400 web-based utility and use the Setup tab > Mobile
Network page and the Setup tab > Ethernet Recovery page. For more
information, see “Setup > Mobile Network,” on page 43 and “Setup >
Connection Recovery,” on page 46.
Q.
How do you know which mobile network you are using?
Follow these instructions:
a. Open a web browser.
b. Enter the IP address of the WRP400 in the Address field (the default IP
address is 192.168.15.1). Then press Enter.
c. When prompted, complete the User name and Password fields (the
default user name and password is admin). Click OK.
d. Click the Status tab.
e. Click the Mobile Network tab. In the Mobile Network Status section, on
the Carrier line, you will see the name of the network that you are
currently using.
Q.
Can I make a VoIP call over the mobile broadband network?
If the WRP400 is configured to use a Mobile Broadband USB modem and
voice services with an Internet telephony service provider, the WRP400 can
send and receive voice traffic over the mobile broadband network.
However, because a voice service is more sensitive to latency and network
congestion compared to data services, your voice quality over the mobile
network cannot be guaranteed.
Q.
What if my Mobile Broadband USB modem is not supported on the
WRP400?
Cisco is continuously adding support for more Mobile Broadband USB
modems and works closely with mobile broadband providers and
manufacturers to stay current with the latest devices available. For a current
list of supported Mobile Broadband USB Modems, visit the WRP400
product page at www.cisco.com/en/US/products/ps10028/index.html
Cisco WRP400 User Guide
127
B
Specifications
Data
Networking
MAC Address (IEEE 802.3)
IPv4 - Internet Protocol v4 (RFC 791) upgradeable to v6 (RFC 1883)
ARP - Address Resolution Protocol
DNS - A Record (RFC 1706), SRV Record (RFC 2782)
DHCP Client - Dynamic Host Configuration Protocol (RFC 2131)
DHCP Server - Dynamic Host Configuration Protocol (RFC 2131)
PPPoE Client - Point to Point Protocol over Ethernet (RFC 2516)
ICMP - Internet Control Message Protocol (RFC792)
TCP - Transmission Control Protocol (RFC793)
UDP - User Datagram Protocol (RFC768)
RTP - Real Time Protocol (RFC 1889) (RFC 1890)
RTCP - Real Time Control Protocol (RFC 1889)
TFTP
RTSP
HTTP
NAT (RFC 1631)
Reverse NAT
SDP
Type of Service - TOS (RFC 791/1349)
SNTP - Simple Network Time Protocol (RFC 2030)
QoS - Packet Prioritization by Type
MAC Address Cloning
Port Forwarding
IP Multicast / IGMP v1/v2/v3 / IGMP proxy / IGMP Immediate Leave
Cisco WRP400 User Guide
128
B
Specifications
Voice Features Voice Algorithms
•
G.711 (a-law and μ-Law)
•
G.726 (16/24/32/40 kbps)
•
G.729 AB
Call Forwarding: No Answer/Busy/Unconditional
Support for two simultaneous calls, including G.729
SIP TLS (Transport Layer Security)
Call Transfer
Call Waiting/Hold/Retrieve
Three-way Conferencing
Call ID number & name (primary line & on Call waiting)
Caller ID Block (prevent sending of caller ID)
Anonymous Call Blocking
Distinctive ringing
Do not Disturb Setting
Repeat Dialing on Busy
Call Return
Emergency Call Support
Dial plan
Speed Dial
In-Band/ SIP-INFO DTMF Translation
Voice RFCs
Compliance
RFC 3261 (SIP: Session Initiation Protocol)
RFC 3262 (PRACK : Provisional Response ACK)
RFC 3263 (Locating SIP Servers)
RFC 3264 (SDP Answer and Offer)
RFC 3265 (SIP Specific Event Notification)
RFC 3550 (RTP: Real Time Protocol)
RFC 3551 (RTP: Real Time Protocol for AVP)
RFC 2327 (SDP: Session Description Protocol)
RFC 3428 (SIP Extensions for Instant Messaging)
RFC 3261 (SIP: Session Initiation Protocol)
RFC 3262 (PRACK : Provisional Response ACK)
RFC 3263 (Locating SIP Servers)
Cisco WRP400 User Guide
129
B
Specifications
Voice RFCs
Compliance
continued
RFC 3264 (SDP Answer and Offer)
RFC 3265 (SIP Specific Event Notification)
RFC 3550 (RTP: Real Time Protocol)
RFC 3551 (RTP: Real Time Protocol for AVP)
RFC 2327 (SDP: Session Description Protocol)
RFC 3428 (SIP Extensions for Instant Messaging)
RFC 3515 (SIP Refer)
RFC 3581 (SIP Extensions for Symmetric Response Routing)
RFC 3842 (SIP Message Summary and Message Waiting Indication)
RFC 3856 (SIP Presence Event Package)
RFC 3891 (SIP "Replaces" Header)
RFC 4028 (SIP Session Timers)
RFC 2976 (SIP INFO)
RFC 2617 (HTTP Authentication : Basic and Digest Access
Authentication)
RFC 3325 (Private Extensions to the SIP for Asserted Identity within
Trusted Network)
RFC 3489 (STUN)
RFC 3863 (Presence Event Package for SIP)
RFC 3428 (SIP Extension for Instant Messaging (Message Method))
RFC 3665 (SIP Basic Call Flow Example)
RFC 4235 (An Invite - Initiated Dialog Event Package for SIP)
RFC 3339 (Date and Time on the Internet : Timestamps)
RFC 3362 (Support of T.38 in SIP) Only sdPv2
RFC 3892 (SIP Referred-By Mechanism)
RFC 3555 (MIME Type Registration of RTP Payload Formats)
RFC 2782 (A DNS RR for specifying the location of services (DNS SRV))
RFC 4235 (An INVITE-Initiated Dialog Event Package for SIP)
RFC 3455 (Private Header (P-Header) Extensions to SIP for 3GPP)
RFC 3323 (A Privacy Mechanism for SIP)
RFC 3420 (Internet Media Type Message/Sipfrag)
RFC 2833 (RTP Payload for DTMF, Telephone Tone and Signals)
RFC 3711 (SRTP)
Cisco WRP400 User Guide
130
B
Specifications
Voice RFCs
Compliance
continued
RFC 2396 (URI : Generic Identifier)
Draft-ieft-mmusic-media-loopback-04.txt (Media Loopback)
Draft-ietf-sip-privacy-04.txt (Remote-party ID)
Provisioning,
Web Browser Administration & Configuration via Integral Web Server
Administration
Telephone Key Pad Configuration with Interactive Voice Prompts
and
Maintenance: Provisioning/Configuration/Authentication via HTTPS, HTTP, TFTP
Provisioning Support for Configuring Router/Data and Voice Parameters
Asynchronous Notification of Upgrade Availability via NOTIFY
Non-intrusive, In-Service Upgrades
Report Generation & Event Logging
Stats in BYE Message
Syslog & Debug Server Records
Per Line and Purpose Configurable Syslog and Debug Options
Physical
Interfaces:
4 100baseT RJ-45 Ethernet LAN Port (IEEE 802.3u)
1 100baseT RJ-45 Ethernet WAN Port (IEEE 802.3u)
2 RJ-11 FXS Phone Ports - For Analog Circuit Telephone Device
USB 2.0 for Mobile Broadband Connection modems (available
separately)
Buttons
Reset, WPS
Subscriber
Line Interface
Circuit (SLIC)
Ring Voltage: 40-55 Vrms
Ring Frequency: 10 Hz ~ 40Hz
Ring Waveform: Trapezoidal and Sinosoidal
Maximum Ringer Load: 3 REN
On-hook/off-hook Characteristics:
•
On-hook voltage (tip/ring): - 46 ~ -56V
•
Off-hook current: 18 ~ 20mA
Frequency Response: 300 – 3400Hz
Terminating Impedance : 8 Configurable Settings including North
America 600 ohms, European CTR21
Cisco WRP400 User Guide
Regulatory
Compliance:
FCC (Part 15 Class B), CE, ICES-003, RoHS, UL, A-Tick, NZ Telepermit, CB
Number of
Antennas
1
Connector
Type
Fixed
131
B
Specifications
Detachable
Antenna
No
RF Pwr (EIRP)
in dBm
Average, not including antenna:
802.11g: Typ. 18 dBm @ Normal Temp Range(with PA)
802.11b: Typ: 20 dBm @ Normal Temp Range (with PA)"
Antenna Gain in 2 dBi
dBi
UPnP able/cert Yes
Power Supply
Switching Type (100-240v) Automatic
DC Input Voltage: +5 VDC at 2.0 A Max.
Power Consumption: 7.9 WATTs (Average)
Power Adapter: 100-240v - 50-60Hz (26-34VA) AC Input, 1.8m cord
Indicator
Lights/LED
Power, Ethernet 1-4, Wireless, Phone 1, Phone 2, Internet, WPS
Documentation Quick Installation and User Guide are downloaded from www.cisco.com/
go/smallbiz
SPA ATA Administration Guide - Service Providers Only
Provisioning Guide - Service Providers Only
Security
features
"Password protected configuration for web & voice access
Stateful Packet Inspection (SPI) Firewall Protection
Denial of Service (DoS) Prevention
URL filtering, and keyword, Java, ActiveX, Proxy, Cookie blocking
VPN Passthrough for IPSec, PPTP, and L2TP Protocols
Access restriction by MAC and IP addresses
MAC Filtering Security Feature
SSID Broadcast Disable
64, 128 bits WEP with Passphrase WEP key generation
Wi-Fi Protected Access™ (WPA), Wi-Fi Protected Access™ 2 (WPA2)
Wi-Fi Protected Setup (WPS)"
Cisco WRP400 User Guide
Security key
bits
64, 128
Device
Dimensions
WidthHeightDepthWeight
Metric14014027mm0.285 kg
English5.515.511.06inches0.63 lbs or 10.05 oz
Power
External, Switching 5VDC 2A
Certification
FCC, CE, CB, IC, UL, Wi-Fi (802.11b + WPA2, 802.11g + WPA2, WMM,
WPS)
132
B
Specifications
Operating
Temperature
0° C to 40° C (32° F to 104° F)
Storage
Temperature
-20° C to 60° C (-4° F to 140° F)
Operating
Humidity
10% to 85% relative humidity, Non-Condensing
Storage
Humidity
5% to 90% Non-Condensing
NOTE Many specifications are programmable within a defined range or list of options.
Please see the ATA Administration Guide for details. The target configuration
profile is uploaded to the WRP400 at the time of provisioning.
NOTE Specifications are subject to change without notice.
Cisco WRP400 User Guide
133
C
Regulatory Information
This appendix includes the following regulatory statements:
•
“Federal Communications Commission Interference Statement,” on
page 134
•
“Safety Notices and Information,” on page 136
•
“Industry Canada Statement,” on page 137
•
“Avis d’Industrie Canada,” on page 138
•
“Telepermit Statement,” on page 139
•
“Statement 287—Declaration of Conformity to R&TTE Directive 1999/
5/EC for the European Community, Switzerland, Norway, Iceland and
Liechtenstein,” on page 139
•
“CE Marking,” on page 142
•
“National Restrictions,” on page 143
•
“Product Usage Restrictions,” on page 146
•
“User Information for Consumer Products Covered by EU Directive
2002/96/EC on Waste Electric and Electronic Equipment (WEEE),” on
page 146
Federal Communications Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Cisco WRP400 User Guide
134
C
Regulatory Information
This product has been tested and complies with the specifications for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used according to the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which is found by turning the
equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment or devices
•
Connect the equipment to an outlet other than the receiver’s
•
Consult a dealer or an experienced radio/TV technician for assistance
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 25 cm between the radiator and your body.
This device has been tested and passed co-located EMC / RF exposure test with
the following three 3G cards, as described in this filing. Other 3G cards with
substantially similar physical dimensions, construction, and electrical and RF
characteristics may or may not comply with FCC rule, please consult manufacture
before purchase.
Item
Brand Name
Model Name
FCC ID
1
Sierra Wireless, Inc.
AirCard 595U
N7N-MC5725U
2
Novatel Wireless, Inc.
U720
PKRNVWMCD3000
3
Novatel Wireless, Inc.
U727
PKRNVWMCD727
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. IEEE 802.11b or 802.11g operation of this product in the
USA is firmware-limited to channels 1 through 11.
Cisco WRP400 User Guide
135
C
Regulatory Information
Safety Notices and Information
!
CAUTION:
•
To reduce the risk of fire, use only No.26
AWG or larger telecommunication line cord.
•
Do not use this product near water, for
example, in a wet basement or near a
swimming pool.
•
Avoid using this product during an electrical
storm. There may be a remote risk of
electric shock from lightning.
WARNING: This product contains lead,
known to the State of California to cause
cancer, and birth defects or other reproductive
harm. Wash hands after handling.
WARNING: This equipment will be inoperable
when main power fails.
WARNING: Many Internet phone service
providers do not support calls to emergency
service numbers (000 in Australia or 111 in
New Zealand). An alternative phone should be
used to make emergency calls.
Cisco WRP400 User Guide
136
C
Regulatory Information
WARNING: To ensure compliance with
explosure limits to radiofrequency fields, the
antenna of the WRP400 should be no closer
than 20 cm from the body during use.
Industry Canada Statement
This device complies with Industry Canada ICES-003 rule.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
Industry Canada Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 25 cm between the radiator & your body.
This device has been tested and passed co-located EMC / RF exposure test with
the following three 3G cards, as described in this filing. Other 3G cards with
substantially similar physical dimensions, construction, and electrical and RF
characteristics may or may not comply with FCC rule, please consult manufacture
before purchase.
Item
Cisco WRP400 User Guide
Brand Name
Model Name
FCC ID
1
Sierra Wireless, Inc.
AirCard 595U
N7N-MC5725U
2
Novatel Wireless, Inc.
U720
PKRNVWMCD3000
3
Novatel Wireless, Inc.
U727
PKRNVWMCD727
137
C
Regulatory Information
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Avis d’Industrie Canada
Cet appareil numérique de la classe B est conforme aux normes NMB-003 et
RSS210 du Canada.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
1. il ne doit pas produire de brouillage et
2. il doit accepter tout brouillage radioélectrique reçu, même si ce brouillage est
susceptible de compromettre le fonctionnement du dispositif.
Afin de réduire le risque d’interférence aux autres utilisateurs, le type d’antenne
et son gain doivent être choisis de façon à ce que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour
obtenir une communication satisfaisante.
Avis d’Industrie Canada concernant l’exposition aux
radiofréquences :
Ce matériel est conforme aux limites établies par IC en matière d’exposition aux
radiofréquences dans un environnement non contrôlé. Ce matériel doit être installé
et utilisé à une distance d’au moins 25 cm entre l’antenne et le corps de l’utilisateur.
L’émetteur ne doit pas être placé près d’une autre antenne ou d’un autre émetteur,
ou fonctionner avec une autre antenne ou un autre émetteur.
Wireless Disclaimer
The maximum performance for wireless is derived from IEEE Standard 802.11
specifications. Actual performance can vary, including lower wireless network
capacity, data throughput rate, range and coverage. Performance depends on
many factors, conditions and variables, including distance from the access point,
volume of network traffic, building materials and construction, operating system
used, mix of wireless products used, interference and other adverse conditions.
Cisco WRP400 User Guide
138
C
Regulatory Information
Avis de non-responsabilité concernant les appareils sans fil
Les performances maximales pour les réseaux sans fil sont tirées des
spécifications de la norme IEEE 802.11. Les performances réelles peuvent varier,
notamment en fonction de la capacité du réseau sans fil, du débit de la
transmission de données, de la portée et de la couverture. Les performances
dépendent de facteurs, conditions et variables multiples, en particulier de la
distance par rapport au point d’accès, du volume du trafic réseau, des matériaux
utilisés dans le bâtiment et du type de construction, du système d’exploitation et
de la combinaison de produits sans fil utilisés, des interférences et de toute autre
condition défavorable.
Telepermit Statement
The cabling between the phone port and the phone shall not exceed 100 metres.
Statement 287—Declaration of Conformity to R&TTE
Directive 1999/5/EC for the European Community,
Switzerland, Norway, Iceland and Liechtenstein
English:
This equipment is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC.
[Bulgarian]:
[Czech]:
Dansk
[Danish]:
Deutsch
[German]:
Dette udstyr er i overensstemmelse med de væsentlige krav og andre relevante
bestemmelser i Direktiv 1999/5/EF.
Dieses Gerät entspricht den grundlegenden Anforderungen und den weiteren
entsprechenden Vorgaben der Richtlinie 1999/5/EU.
Cisco WRP400 User Guide
139
Regulatory Information
Eesti
[Estonian]:
See seade vastab direktiivi 1999/5/EÜ olulistele nõuetele ja teistele
asjakohastele sätetele.
Español
[Spanish]:
Este equipo cumple con los requisitos esenciales asi como con otras
disposiciones de la Directiva 1999/5/CE.
C
[Greek]:
Français
[French]:
Cet appareil est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la Directive 1999/5/EC.
Íslenska
[Icelandic]:
Þetta tæki er samkvæmt grunnkröfum og öðrum viðeigandi ákvæðum Tilskipunar
1999/5/EC.
Italiano
[Italian]:
Questo apparato é conforme ai requisiti essenziali ed agli altri principi sanciti
dalla Direttiva 1999/5/CE.
Latviski
[Latvian]:
[Lithuanian]:
Nederlands
[Dutch]:
Dit apparaat voldoet aan de essentiele eisen en andere van toepassing zijnde
bepalingen van de Richtlijn 1999/5/EC.
Malti
[Maltese]:
Magyar
[Hungarian]:
Norsk
[Norwegian]:
Dette utstyret er i samsvar med de grunnleggende krav og andre relevante
bestemmelser i EU-direktiv 1999/5/EF.
Polski
[Polish]:
Português
[Portuguese]:
Este equipamento está em conformidade com os requisitos essenciais e outras
provisões relevantes da Directiva 1999/5/EC.
Cisco WRP400 User Guide
140
Regulatory Information
C
Acest echipament este in conformitate cu cerintele esentiale si cu alte prevederi
[Romanian]: relevante ale Directivei 1999/5/EC.
Slovensko
[Slovenian]:
Ta naprava je skladna z bistvenimi zahtevami in ostalimi relevantnimi pogoji
Direktive 1999/5/EC.
Slovensky
[Slovak]:
Toto zariadenie je v zhode so základnými požiadavkami a inými príslušnými
nariadeniami direktív: 1999/5/EC.
Suomi
[Finnish]:
Svenska
[Swedish]:
Latviski
Malti
Magyar
Polski
Cisco WRP400 User Guide
141
C
Regulatory Information
Suomi
Svenska
For all products, the Declaration of Conformity (DofC) is available through one or
more of these options:
•
A pdf file is included on the product’s CD.
•
A print copy is included with the product.
•
A pdf file is available on the product’s webpage. Visit www.cisco.com/go/
smallbusiness.
If you need any other technical documentation, see Appendix E, “Additional
Information.”.
The following standards were applied during the assessment of the product
against the requirements of the Directive 1999/5/EC:
•
Radio: EN 300 328 and/or EN 301 893 as applicable
•
EMC: EN 301 489-1, EN 301 489-17
•
Safety: EN 60950 and either EN 50385 or EN 50371
Dynamic Frequency Selection (DFS) and Transmit Power Control (TPC) are
required for operation in the 5 GHz band.
DFS: The equipment meets the DFS requirements as defined in ETSI EN 301 893.
This feature is required by the regulations to avoid interference with Radio
Location Services (radars).
TPC: For operation in the 5 GHz band, the maximum power level is 3 dB or more
below the applicable limit. As such, TPC is not required.
CE Marking
For the Wireless-N, -G, -B, and/or -A products, the following CE mark, notified body
number (where applicable), and class 2 identifier are added to the equipment.
Cisco WRP400 User Guide
142
C
Regulatory Information
or
or
or
Check the CE label on the product to find out which notified body was involved
during the assessment.
National Restrictions
This product may be used in all EU countries (and other countries following the EU
directive 1999/5/EC) without any limitation except for the countries mentioned
below:
Ce produit peut être utilisé dans tous les pays de l’UE (et dans tous les pays
ayant transposés la directive 1999/5/CE) sans aucune limitation, excepté pour
les pays mentionnés ci-dessous:
Questo prodotto è utilizzabile in tutte i paesi EU (ed in tutti gli altri paesi che
seguono le direttive EU 1999/5/EC) senza nessuna limitazione, eccetto per i
paesii menzionati di seguito:
Das Produkt kann in allen EU Staaten ohne Einschränkungen eingesetzt werden
(sowie in anderen Staaten die der EU Direktive 1999/5/CE folgen) mit
Außnahme der folgenden aufgeführten Staaten:
In the majority of the EU and other European countries, the 2,4- and 5-GHz bands
have been made available for the use of wireless local area networks (LANs). The
table labeled “Overview of Regulatory Requirements for Wireless LANs” provides
an overview of the regulatory requirements applicable for the 2,4- and 5-GHz
bands.
Later in this document you will find an overview of countries in which additional
restrictions or requirements or both are applicable.
Cisco WRP400 User Guide
143
C
Regulatory Information
The requirements for any country may evolve. Cisco recommends that you check
with the local authorities for the latest status of their national regulations for both
the 2,4- and 5-GHz wireless LANs.
Table 1
Overview of Regulatory Requirements for Wireless LANs
Frequency Band
(MHz)
Max Power Level
(EIRP) (mW)
2400-2483.5
100
5150-5350*
200
5470-5725*
1000
Indoor ONLY
Indoor &
Outdoor
X
X
X
*Dynamic Frequency Selection and Transmit Power Control are required in the
frequency ranges of 5250-5350 MHz and 5470-5725 MHz.
The following countries have restrictions and/or requirements in addition to those
given in the “Overview of Regulatory Requirements for Wireless LANs” table:
Denmark
In Denmark, the band 5150 - 5350 MHz is also allowed for outdoor usage.
I Danmark må frekvensbåndet 5150 - 5350 også anvendes udendørs.
France
For 2,4 GHz, the product should not be used outdoors in the band 2454 - 2483,5
MHz. There are no restrictions when used in other parts of the 2,4 GHz band when
used indoors. Check http://www.arcep.fr/ for more details.
Pour la bande 2,4 GHz, l’ équipement ne doit pas être utilisé en extérieur dans
la bande 2454 - 2483,5 MHz. Il n’y a pas de restrictions pour des utilisations en
intérieur dans d’autres parties de la bande 2,4GHz. Consultez http://
www.arcep.fr/ pour de plus amples détails.
Cisco WRP400 User Guide
144
C
Regulatory Information
Table 2
Applicable Power Levels in France
Location
Frequency Range
(MHz)
Power (EIRP)
Indoor
(No restrictions)
2400-2483.5
100 mW (20 dBm)
Outdoor
2400-2454
2454-2483.5
100 mW (20 dBm)
10 mW (10 dBm)
Italy
This product meets the National Radio Interface and the requirements specified in
the National Frequency Allocation Table for Italy. Unless this 2,4-GHz wireless LAN
product is operating within the boundaries of the owner’s property, its use
requires a “general authorization.” Please check http://www.comunicazioni.it/it/
for more details.
Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e
rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene
installato all’interno del proprio fondo, l’utilizzo di prodotti Wireless LAN a
2,4 GHz richiede una “Autorizzazione Generale”. Consultare
http://www.comunicazioni.it/it/ per maggiori dettagli.
Latvia
The outdoor usage of the 2,4 GHz band requires an authorization from the
Electronic Communications Office. Please check http://www.esd.lv for more
details.
2,4 GHz frekveu joslas izmantošanai rpus telpm nepieciešama atauja no
Elektronisko sakaru direkcijas. Vairk informcijas: http://www.esd.lv.
Notes:
1. Although Norway, Switzerland and Liechtenstein are not EU member states, the
EU Directive 1999/5/EC has also been implemented in those countries.
2. The regulatory limits for maximum output power are specified in EIRP. The EIRP
level of a device can be calculated by adding the gain of the antenna used
(specified in dBi) to the output power available at the connector (specified in
dBm).
Cisco WRP400 User Guide
145
C
Regulatory Information
Product Usage Restrictions
This product is designed for indoor usage only. Outdoor usage is not
recommended, unless otherwise noted.
2,4 GHz Restrictions
This product is designed for use with the standard, integral or dedicated (external)
antenna(s) that is/are shipped together with the equipment. However, some
applications may require the antenna(s), if removable, to be separated from the
product and installed remotely from the device by using extension cables. For
these applications, Cisco offers an R-SMA extension cable (AC9SMA) and an RTNC extension cable (AC9TNC). Both of these cables are 9 meters long and have a
cable loss (attenuation) of 5 dB. To compensate for the attenuation, Cisco also
offers higher gain antennas, the HGA7S (with R-SMA connector) and HGA7T (with
R-TNC connector). These antennas have a gain of 7 dBi and may only be used with
either the R-SMA or R-TNC extension cable.
Combinations of extension cables and antennas resulting in a radiated power level
exceeding 100 mW EIRP are illegal.
Third-Party Software or Firmware
The use of software or firmware not supported/provided by Cisco may result that
the equipment is no longer compliant with the regulatory requirements.
User Information for Consumer Products Covered by EU
Directive 2002/96/EC on Waste Electric and Electronic
Equipment (WEEE)
This document contains important information for users with regards to the proper
disposal and recycling of Cisco products. Consumers are required to comply with
this notice for all electronic products bearing the following symbol:
Cisco WRP400 User Guide
146
C
Regulatory Information
English - Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product
and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates
that this product should be disposed of separately from regular household waste streams. It is your
responsibility to dispose of this and other electric and electronic equipment via designated
collection facilities appointed by the government or local authorities. Correct disposal and recycling
will help prevent potential negative consequences to the environment and human health. For more
detailed information about the disposal of your old equipment, please contact your local
authorities, waste disposal service, or the shop where you purchased the product.
Ceština (Czech) - Informace o ochran životního prostedí pro zákazníky v zemích Evropské unie
Evropská smrnice 2002/96/ES zakazuje, aby zaízení oznaené tímto symbolem na produktu anebo na
obalu bylo likvidováno s netídným komunálním odpadem. Tento symbol udává, že daný produkt
musí být likvidován oddlen od bžného komunálního odpadu. Odpovídáte za likvidaci tohoto
produktu a dalších elektrických a elektronických zaízení prostednictvím urených sbrných míst
stanovených vládou nebo místními úady. Správná likvidace a recyklace pomáhá pedcházet
potenciálním negativním dopadm na životní prostedí a lidské zdraví. Podrobnjší informace o
likvidaci starého vybavení si laskav vyžádejte od místních úad, podniku zabývajícího se likvidací
komunálních odpad nebo obchodu, kde jste produkt zakoupili.
Cisco WRP400 User Guide
147
C
Regulatory Information
Dansk (Danish) - Miljøinformation for kunder i EU
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol på produktet og/eller emballagen
ikke må bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal
bortskaffes adskilt fra det almindelige husholdningsaffald. Det er dit ansvar at bortskaffe dette og
andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de
lokale myndigheder. Korrekt bortskaffelse og genvinding vil hjælpe med til at undgå mulige skader
for miljøet og menneskers sundhed. Kontakt venligst de lokale myndigheder, renovationstjenesten
eller den butik, hvor du har købt produktet, angående mere detaljeret information om bortskaffelse
af dit gamle udstyr.
Deutsch (German) - Umweltinformation für Kunden innerhalb der Europäischen Union
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische Ausrüstung, die direkt am Gerät
und/oder an der Verpackung mit diesem Symbol versehen ist , nicht zusammen mit unsortiertem
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem
Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses Gerät und
andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung
oder örtlichen Behörden dazu bestimmten Sammelstellen zu entsorgen. Ordnungsgemäßes
Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die
menschliche Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur Entsorgung Ihrer
Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen
Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.
Eesti (Estonian) - Keskkonnaalane informatsioon Euroopa Liidus asuvatele klientidele
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on seadmeid, millel on tootel või pakendil
käesolev sümbol , keelatud kõrvaldada koos sorteerimata olmejäätmetega. See sümbol näitab, et
toode tuleks kõrvaldada eraldi tavalistest olmejäätmevoogudest. Olete kohustatud kõrvaldama
käesoleva ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike ametiasutuste poolt ette
nähtud kogumispunktide kaudu. Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida
võimalikke negatiivseid tagajärgi keskkonnale ning inimeste tervisele. Vanade seadmete
kõrvaldamise kohta täpsema informatsiooni saamiseks võtke palun ühendust kohalike
ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te toote ostsite.
Español (Spanish) - Información medioambiental para clientes de la Unión Europea
La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato
y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El
símbolo indica que el producto en cuestión debe separarse de los residuos domésticos
convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera
otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su
disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos
aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y
la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de
su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de
residuos de su zona o pregunte en la tienda donde adquirió el producto.
Cisco WRP400 User Guide
148
Regulatory Information
C
Français (French) - Informations environnementales pour les clients de l’Union européenne
La directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole sur
le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole
indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des
ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel électrique
ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics
des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de
lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé
publique. Pour plus d’informations sur le mode d’élimination de votre ancien équipement, veuillez
prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit
où vous avez acheté le produit.
Italiano (Italian) - Informazioni relative all’ambiente per i clienti residenti nell’Unione Europea
La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo
simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non
differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali
rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre
apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal
governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire
conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere
informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso,
Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio
nel quale avete acquistato il prodotto.
Latviešu valoda (Latvian) - Ekoloiska informcija klientiem Eiropas Savienbas jurisdikcij
Direktv 2002/96/EK ir prasba, ka aprkojumu, kam pievienota zme uz paša izstrdjuma vai uz t
iesaiojuma, nedrkst izmest neširot veid kop ar komunlajiem atkritumiem (tiem, ko rada vietji
iedzvotji un uzmumi). Š zme nozm to, ka š ierce ir jizmet atkritumos t, lai t nenonktu kop ar parastiem
mjsaimniecbas atkritumiem. Jsu pienkums ir šo un citas elektriskas un elektroniskas ierces izmest
atkritumos, izmantojot pašus atkritumu savkšanas veidus un ldzekus, ko nodrošina valsts un
pašvaldbu iestdes. Ja izmešana atkritumos un prstrde tiek veikta pareizi, tad mazins iespjamais
Cisco WRP400 User Guide
149
C
Regulatory Information
kaitjums dabai un cilvku veselbai. Skkas zias par novecojuša aprkojuma izmešanu atkritumos js varat
saemt vietj pašvaldb, atkritumu savkšanas dienest, k ar veikal, kur iegdjties šo izstrdjumu.
Lietuvškai (Lithuanian) - Aplinkosaugos informacija, skirta Europos Sjungos vartotojams
Europos direktyva 2002/96/EC numato, kad rangos, kuri ir kurios pakuot yra pažymta šiuo simboliu
(veskite simbol), negalima šalinti kartu su neršiuotomis komunalinmis atliekomis. Šis simbolis rodo,
kad gamin reikia šalinti atskirai nuo bendro buitini atliek srauto. Js privalote užtikrinti, kad ši ir kita
elektros ar elektronin ranga bt šalinama per tam tikras nacionalins ar vietins valdžios nustatytas
atliek rinkimo sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta galimos žalos aplinkai ir
žmoni sveikatai. Daugiau informacijos apie js senos rangos šalinim gali pateikti vietins valdžios
institucijos, atliek šalinimo tarnybos arba parduotuvs, kuriose sigijote t gamin.
Malti (Maltese) - Informazzjoni Ambjentali gal Klijenti fl-Unjoni Ewropea
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagmir li jkun fih is-simbolu fuq il-prodott u/jew fuq lippakkjar ma jistax jintrema ma’ skart muniipali li ma iex isseparat. Is-simbolu jindika li dan il-prodott
gandu jintrema separatament minn ma’ l-iskart domestiku regolari. Hija responsabbiltà tiegek li
tarmi dan it-tagmir u kull tagmir ieor ta’ l-elettriku u elettroniku permezz ta’ failitajiet ta’ bir
appuntati apposta mill-gvern jew mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riikla jgin
jipprevjeni konsegwenzi negattivi potenzjali gall-ambjent u gas-saa tal-bniedem. Gal aktar
informazzjoni dettaljata dwar ir-rimi tat-tagmir antik tiegek, jekk jogbok ikkuntattja lill-awtoritajiet
lokali tiegek, is-servizzi gar-rimi ta’ l-iskart, jew il-anut minn fejn xtrajt il-prodott.
Magyar (Hungarian) - Környezetvédelmi információ az európai uniós vásárlók számára
A 2002/96/EC számú európai uniós irányelv megkívánja, hogy azokat a termékeket, amelyeken, és/
vagy amelyek csomagolásán az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági
hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott termék kidobásakor a szokványos
háztartási hulladékelszállítási rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön felelõssége,
hogy ezt, és más elektromos és elektronikus berendezéseit a kormányzati vagy a helyi hatóságok
által kijelölt gyjtõredszereken keresztül számolja fel. A megfelelõ hulladékfeldolgozás segít a
környezetre és az emberi egészségre potenciálisan ártalmas negatív hatások megelõzésében. Ha
elavult berendezéseinek felszámolásához további részletes információra van szüksége, kérjük,
lépjen kapcsolatba a helyi hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal üzlettel, ahol
a terméket vásárolta.
Nederlands (Dutch) - Milieu-informatie voor klanten in de Europese Unie
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit symbool op het
product of de verpakking, niet mag worden ingezameld met niet-gescheiden huishoudelijk afval.
Dit symbool geeft aan dat het product apart moet worden ingezameld. U bent zelf verantwoordelijk
voor de vernietiging van deze en andere elektrische en elektronische apparatuur via de daarvoor
door de landelijke of plaatselijke overheid aangewezen inzamelingskanalen. De juiste vernietiging
en recycling van deze apparatuur voorkomt mogelijke negatieve gevolgen voor het milieu en de
gezondheid. Voor meer informatie over het vernietigen van uw oude apparatuur neemt u contact
op met de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product
hebt aangeschaft.
Cisco WRP400 User Guide
150
C
Regulatory Information
Norsk (Norwegian) - Miljøinformasjon for kunder i EU
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol avbildet på produktet og/eller
pakningen, ikke må kastes sammen med usortert avfall. Symbolet indikerer at dette produktet skal
håndteres atskilt fra ordinær avfallsinnsamling for husholdningsavfall. Det er ditt ansvar å kvitte deg
med dette produktet og annet elektrisk og elektronisk avfall via egne innsamlingsordninger slik
myndighetene eller kommunene bestemmer. Korrekt avfallshåndtering og gjenvinning vil være
med på å forhindre mulige negative konsekvenser for miljø og helse. For nærmere informasjon om
håndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon
for avfall eller butikken der du kjøpte produktet.
Polski (Polish) - Informacja dla klientów w Unii Europejskiej o przepisach dotyczcych ochrony
rodowiska
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzt oznaczony symbolem znajdujcym si na
produkcie i/lub jego opakowaniu nie by wyrzucany razem z innymi niesortowanymi odpadami
komunalnymi. Symbol ten wskazuje, e produkt nie powinien by usuwany razem ze zwykymi
odpadami z gospodarstw domowych. Na Pastwu spoczywa obowizek wyrzucania tego i innych
urzdze elektrycznych oraz elektronicznych w punktach odbioru wyznaczonych przez wadze krajowe
lub lokalne. Pozbywanie si sprztu we waciwy sposób i jego recykling pomog zapobiec potencjalnie
negatywnym konsekwencjom dla rodowiska i zdrowia ludzkiego. W celu uzyskania szczegóowych
informacji o usuwaniu starego sprztu, prosimy zwróci si do lokalnych wadz, sub oczyszczania miasta
lub sklepu, w którym produkt zosta nabyty.
Português (Portuguese) - Informação ambiental para clientes da União Europeia
A Directiva Europeia 2002/96/CE exige que o equipamento que exibe este símbolo no produto e/ou
na sua embalagem não seja eliminado junto com os resíduos municipais não separados. O símbolo
indica que este produto deve ser eliminado separadamente dos resíduos domésticos regulares. É da
sua responsabilidade eliminar este e qualquer outro equipamento eléctrico e electrónico através
das instalações de recolha designadas pelas autoridades governamentais ou locais. A eliminação e
reciclagem correctas ajudarão a prevenir as consequências negativas para o ambiente e para a
saúde humana. Para obter informações mais detalhadas sobre a forma de eliminar o seu
equipamento antigo, contacte as autoridades locais, os serviços de eliminação de resíduos ou o
estabelecimento comercial onde adquiriu o produto.
Român (Romanian) - Informaii de mediu pentru clienii din Uniunea European
Directiva european 2002/96/CE impune ca echipamentele care prezint acest simbol pe produs i/sau
pe ambalajul acestuia s nu fie casate împreun cu gunoiul menajer municipal. Simbolul indic faptul c
acest produs trebuie s fie casat separat de gunoiul menajer obinuit. Este responsabilitatea dvs. s
casai acest produs i alte echipamente electrice i electronice prin intermediul unitilor de colectare
special desemnate de guvern sau de autoritile locale. Casarea i reciclarea corecte vor ajuta la
prevenirea potenialelor consecine negative asupra sntii mediului i a oamenilor. Pentru mai multe
informaii detaliate cu privire la casarea acestui echipament vechi, contactai autoritile locale, serviciul
de salubrizare sau magazinul de la care ai achiziionat produsul.
Slovenina (Slovak) - Informácie o ochrane životného prostredia pre zákazníkov v Európskej
únii
Cisco WRP400 User Guide
151
C
Regulatory Information
Poda európskej smernice 2002/96/ES zariadenie s týmto symbolom na produkte a/alebo jeho balení
nesmie by likvidované spolu s netriedeným komunálnym odpadom. Symbol znamená, že produkt
by sa mal likvidova oddelene od bežného odpadu z domácností. Je vašou povinnosou likvidova toto
i ostatné elektrické a elektronické zariadenia prostredníctvom špecializovaných zberných zariadení
urených vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia pomôže zabráni
prípadným negatívnym dopadom na životné prostredie a zdravie udí. Ak máte záujem o
podrobnejšie informácie o likvidácii starého zariadenia, obráte sa, prosím, na miestne orgány,
organizácie zaoberajúce sa likvidáciou odpadov alebo obchod, v ktorom ste si produkt zakúpili.
Slovenina (Slovene) - Okoljske informacije za stranke v Evropski uniji
Evropska direktiva 2002/96/EC prepoveduje odlaganje opreme, oznaene s tem simbolom – na
izdelku in/ali na embalaži – med obiajne, nerazvršene odpadke. Ta simbol opozarja, da je treba
izdelek odvrei loeno od preostalih gospodinjskih odpadkov. Vaša odgovornost je, da to in preostalo
elektrino in elektronsko opremo odnesete na posebna zbirališa, ki jih doloijo državne ustanove ali
lokalna uprava. S pravilnim odlaganjem in recikliranjem boste prepreili morebitne škodljive vplive
na okolje in zdravje ljudi. e želite izvedeti ve o odlaganju stare opreme, se obrnite na lokalno upravo,
odpad ali trgovino, kjer ste izdelek kupili.
Suomi (Finnish) - Ympäristöä koskevia tietoja EU-alueen asiakkaille
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboli itse tuotteessa ja/tai sen
pakkauksessa, laitteistoa ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana. Symboli
merkitsee sitä, että tämä tuote on hävitettävä erillään tavallisesta kotitalousjätteestä. Sinun
vastuullasi on hävittää tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet viemällä
tuote tai tuotteet viranomaisten määräämään keräyspisteeseen. Laitteiston oikea hävittäminen
estää mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten terveyteen. Lisätietoja vanhan
laitteiston oikeasta hävitystavasta saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä
myymälästä, josta ostit tuotteen.
Svenska (Swedish) - Miljöinformation för kunder i Europeiska unionen
Det europeiska direktivet 2002/96/EC kräver att utrustning med denna symbol på produkten och/
eller förpackningen inte får kastas med osorterat kommunalt avfall. Symbolen visar att denna
produkt bör kastas efter att den avskiljts från vanligt hushållsavfall. Det faller på ditt ansvar att kasta
denna och annan elektrisk och elektronisk utrustning på fastställda insamlingsplatser utsedda av
regeringen eller lokala myndigheter. Korrekt kassering och återvinning skyddar mot eventuella
negativa konsekvenser för miljön och personhälsa. För mer detaljerad information om kassering av
din gamla utrustning kontaktar du dina lokala myndigheter, avfallshanteringen eller butiken där du
köpte produkten.
Cisco WRP400 User Guide
152
D
Where to Go From Here
This appendix describes additional resources that are available to help you and
your customer obtain the full benefits of the SPA9000 Voice System.
Cisco WRP400 User Guide
Resource
Location
Technical
Documentation
www.cisco.com/en/US/products/ps10024/
tsd_products_support_series_home.html
Firmware
Downloads
www.cisco.com/en/US/products/ps10024/index.html
Customer Support
www.cisco.com/en/US/support/
tsd_cisco_small_business_support_center_contacts.html
Warranty and End
User License
Agreement
www.cisco.com/go/warranty
Open Source
License Notices
www.cisco.com/go/osln
Regulatory
Compliance and
Safety Information
www.cisco.com/en/US/products/ps10024/
tsd_products_support_series_home.html
Cisco Partner
Central site for Small
Business
www.cisco.com/web/partners/sell/smb
153