Samsung RJ052F3HX Installation manual

Contents
Safety precautions ............................................................................................................................................................................................ 2
Deciding on where to install the air conditioner ................................................................................................................................ 4
Air conditioner and accessories................................................................................................................................................................11
Installing and connecting the drain hose of the outdoor unit ..................................................................................................11
Cutting/extending the piping ..................................................................................................................................................................12
Connecting the cables to the outdoor unit .......................................................................................................................................12
Transmitter installation (optional) ...........................................................................................................................................................16
Checking correct earthing ..........................................................................................................................................................................18
Fixing the unit in position ...........................................................................................................................................................................18
Connecting up and purging the circuit ...............................................................................................................................................19
Adding refrigerant .........................................................................................................................................................................................20
Performing leak tests ....................................................................................................................................................................................21
Pipe installation with indoor units .........................................................................................................................................................22
Setting an indoor unit address and installation option ................................................................................................................23
Troubleshooting .............................................................................................................................................................................................33
Explaining operations to the owner .......................................................................................................................................................35
Pump down procedure (when removing the product) ................................................................................................................35
delete Appendix
Safety precautions
(Carefully follow the precautions listed below because they are essential to guarantee the safety of the equipment.)
WARNING
xAlways disconnect the air conditioner from the power supply before servicing it or
accessing its internal components.
xVerify that installation and testing operations are performed by qualified personnel.
xVerify that the air conditioner is not installed in an easily accessible area.
GENERAL INFORMATION
X Carefully read the content of this manual before installing the air conditioner and store the manual in a safe place in
order to be able to use it as reference after installation.
X For maximum safety, installers should always carefully read the following warnings.
X Store the operation and installation manual in a safe location and remember to hand it over to the new owner if the
air conditioner is sold or transferred.
X This manual explains how to install an indoor unit with a split system with two SAMSUNG units. The use of other types
of units with different control systems may damage the units and invalidate the warranty. The manufacturer shall not
be responsible for damages arising from the use of non compliant units.
X The air conditioner is compliant with the requirements of the Low Voltage Directive (72/23/EEC), the EMC Directive
(89/336/EEC), and the Directive on pressurized equipment (97/23/EEC).
X The manufacturer shall not be responsible for damage originating from unauthorized changes or the improper connection
of electric and hydraulic lines. Failure to comply with these instructions or to comply with the requirements set forth in the
“Operating limits” table, included in the manual, shall immediately invalidate the warranty.
X The air conditioner should be used only for the applications for which it has been designed: the indoor unit is not
suitable to be installed in areas used for laundry.
X Do not use the units if damaged. If problems occur, switch the unit off and disconnect it from the power supply.
2
Safety precautions
GENERAL INFORMATION
ENGLISH
X In order to prevent electric shocks, fires or injuries, always stop the unit, disable the protection switch and contact
SAMSUNG’s technical support if the unit produces smoke, if the power cable is hot or damaged or if the unit is very noisy.
X Always remember to inspect the unit, electric connections, refrigerant tubes and protections regularly.
These operations should be performed by qualified personnel only.
X The unit contains moving parts, which should always be kept out of the reach of children.
X Do not attempt to repair, move, alter or reinstall the unit. If performed by unauthorized personnel, these operations
may cause electric shocks or fires.
X Do not place containers with liquids or other objects on the unit.
X All the materials used for the manufacture and packaging of the air conditioner are recyclable.
X The packing material and exhaust batteries of the remote control(optional) must be disposed of in accordance with
current laws.
X The air conditioner contains a refrigerant that has to be disposed of as special waste. At the end of its life cycle, the air
conditioner must be disposed of in authorized centers or returned to the retailer so that it can be disposed of correctly
and safely.
INSTALLING THE UNIT
IMPORTANT: When installing the unit, always remember to connect first the refrigerant tubes, then the electrical lines.
Always disassemble the electric lines before the refrigerant tubes.
X Upon receipt, inspect the product to verify that it has not been damaged during transport. If the product appears
damaged, DO NOT INSTALL it and immediately report the damage to the carrier or retailer (if the installer or the
authorized technician has collected the material from the retailer.)
X After completing the installation, always carry out a functional test and provide the instructions on how to operate
the air conditioner to the user.
X Do not use the air conditioner in environments with hazardous substances or close to equipment that release free
flames to avoid the occurrence of fires, explosions or injuries.
X To prevent injury when accidentally touching the indoor unit fan, install the indoor unit at least 2.5m above the floor.
X The air conditioner should be used only for the applications for which it has been designed: the indoor unit is not
suitable to be installed in areas used for laundry.
X Our units must be installed in compliance with the spaces indicated in the installation manual to ensure either
accessibility from both sides or ability to perform routine maintenance and repairs. The units’ components must be
accessible and that can be disassembled in conditions of complete safety either for people or things.
For this reason, where it is not observed as indicated into the Installation Manual, the cost necessary to reach and repair
the unit (in safety, as required by current regulations in force) with slings, trucks, scaffolding or any other means of
elevation won’t be considered in-warranty and charged to end user.
POWER SUPPLY LINE, FUSE OR CIRCUIT BREAKER
X Always make sure that the power supply is compliant with current safety standards. Always install the air conditioner in
compliance with current local safety standards.
X Always verify that a suitable grounding connection is available.
X Verify that the voltage and frequency of the power supply comply with the specifications and that the installed power is
sufficient to ensure the operation of any other domestic appliance connected to the same electric lines.
X Always verify that the cut-off and protection switches are suitably dimensioned.
X Verify that the air conditioner is connected to the power supply in accordance with the instructions provided in the
wiring diagram included in the manual.
X Always verify that electric connections (cable entry, section of leads, protections…) are compliant with the electric
specifications and with the instructions provided in the wiring scheme. Always verify that all connections comply with
the standards applicable to the installation of air conditioners.
3
Deciding on Where to Install the Air Conditioner
When deciding on the location of the air conditioner with the owner, the following restrictions must be
taken into account.
General
Do NOT install the air conditioner in a location where it will come into contact with the following elements:
◆ Combustible gases
◆ Saline air
◆ Machine oil
◆ Sulphide gas
◆ Special environmental conditions
◆ The air conditioner should be used only for the applications for which it has been designed : the indoor unit is not
suit able to be installed in areas used for laundry. If you must install the unit in such conditions, first consult your dealer.
Outdoor Unit
◆ The outdoor unit must NEVER be placed on its side or upside down, as the compressor lubrication oil will run into the cooling
circuit and seriously damage the unit.
◆ Choose a location that is dry and sunny, but not exposed to direct sunlight or strong winds.
◆ Do not block any passageways or thoroughfares.
◆ Choose a location where the noise of the air conditioner when running and the discharged air do not disturb any neighbours.
◆ Choose a position that enables the piping and cables to be easily connected to the indoor unit and the recommended
length will be respected.
◆ Install the outdoor unit on a flat, stable surface that can support its weight and does not generate any unnecessary
noise and vibration.
◆ Position the outdoor unit so that the air flow is directed towards the outside, as indicated by the arrows on the top of the unit.
◆ Maintain sufficient clearance around the outdoor unit, as indicated in the diagram on the page opposite.
◆ Make sure that the water dripping from the drain hose runs away correctly and safely.
CAUTION
◆ You have just purchased a Free Joint Multi air conditioner and it has been installed by your installation specialist.
◆ This device must be installed according to the national electrical rules.
◆ Max input power & current is measured according to IEC standard and input power & current is measured according to
ISO standard.
◆ More than 2 indoor units should be installed when you use Free Joint Multi air conditioner.
◆ Our units must be installed in compliance with the spaces indicated in the installation manual to ensure either
accessibility from both sides or ability to perform routine maintenance and repairs.
The units’ components must be accessible and that can be disassembled in conditions of complete safety either for
people or things. For this reason, where it is not observed as indicated into the Installation Manual, the cost necessary to
reach and repair the unit (in safety, as required by current regulations in force) with slings, trucks, scaffolding or any other
means of elevation won’t be considered in-warranty and charged to end user.
◆ With an outdoor unit having net weight upper then 60kg,we suggest do not install it suspended on wall, but considering
floor standing one.
4
◆ RJ040F2HX**/AJ040FCJ2**
Indoor unit
Outdoor unit
RJ040F2HX**
AJ040FCJ2**
Power supply Ø, V, Hz
Outside diameter
Liquid
Gas
Unit
1,220-240,50/60
**020/023/026/035
1/4"
07/09/12**
※ RJ040F2HX**/AJ040FCJ2** Outdoor unit cannot be connected to the following indoor unit combination.
- **052**/MH***FM*A/NJ***LHXEA/**18**/**24**/AJN**
200 mm
or more
100 mm
or more
ENGLISH
**020/023/026/035
07/09/12**
◆ Piping outside diameter
3/8"
160 mm
or more
(h)
(H)
CAUTION
3 m as minimum pipe length: It will reduce noise and
vibration.
600 mm
minimum
A
B
300 mm
minimum
300 mm
minimum
600 mm
minimum
Main power switch
※ The appearance of the unit may be different from the diagram depending on the model.
◆ Piping length and the height
Dimension
Composition
1 Room max
length
20m
A,B
2 Room total max
length
30m
A+B
Max height between
Max height between
indoor unit & outdoor unit
indoor units
15m
7.5m
(H)
(h)
Make at least one round:
It will reduce noise and vibration
※ The appearance of the unit may be different from the diagram depending on the model.
5
A
Deciding
on Where to Install the Air Conditioner
◆ Piping outside diameter
◆ RJ050F2HX**/AJ050FCJ2**
Indoor unit
Outdoor unit
Power supply Ø, V, Hz
**020/023/026/
035/052
07/09/12/18**
RJ050F2HX**
AJ050FCJ2**
1,220-240,50/60
Unit
**020/023/026/
030/035/07/09/12**
**052/18**
Outside diameter
Liquid
Gas
3/8"
1/4"
1/2"
※ RJ050F2HX**/AJ050FCJ2** Outdoor unit cannot be connected to the following indoor unit combination.
- MH052FMEA/MH052FUEA/**24**/AJN052NDEHA
200 mm
or more
160 mm
or more
100 mm
or more
(h)
CAUTION
3 m as minimum pipe length: It will reduce noise and
vibration.
600 mm
minimum
A
B
300 mm
minimum
300 mm
minimum
600 mm
minimum
Main power switch
※ The appearance of the unit may be different from the diagram depending on the model.
◆ Piping length and the height
Dimension
Composition
1 Room max
length
20m
A,B
2 Room total max
length
30m
A+B
Max height between
Max height between
indoor unit & outdoor unit
indoor units
15m
7.5m
(H)
(h)
Make at least one round:
It will reduce noise and vibration
※ The appearance of the unit may be different from the diagram depending on the model.
6
(H)
◆ Piping outside diameter
◆ RJ052/060F3HX**/AJ052/068FCJ3**
Indoor unit
Power supply Ø, V, Hz
1,220-240,50/60
Outside diameter
Liquid
Gas
Unit
**020/023/026/
030/035/07/09/12**
**052/18**
1/4"
ENGLISH
**020/023/026/
030/035/052
07/09/12/18**
Outdoor unit
RJ052F3HX**
RJ060F3HX**
AJ052FCJ3**
AJ068FCJ3**
3/8"
1/2"
※ RJ052F3HX**/AJ052FCJ3** Outdoor unit cannot be connected to the following indoor unit combination.
- MH052FMEA/MH052FUEA/**24**/AJN052NDEHA
200 mm or more
100 mm
or more
160 mm or more
(h) (H)
CAUTION
3 m as minimum pipe length: It will reduce noise and
vibration.
A
600 mm
minimum
B
C
300 mm
minimum
300 mm
minimum
600 mm
minimum
Main power switch
※ The appearance of the unit may be different from the diagram depending on the model.
◆ Piping length and the height
1 Room max
length
Dimension
20m
Composition
A,B,C
3 Room total max
length
RJ052F3HXEA: 50m
RJ060F3HXEA:45m
RJ060F3HXEB:50m
AJ052FCJ3EH:50m
AJ068FCJ3EH:50m
A+B+C
Max height between
Max height between
indoor unit & outdoor unit
indoor units
15m
7.5m
(H)
(h)
Make at least one round:
It will reduce noise and vibration
※ The appearance of the unit may be different from the diagram depending on the model.
7
A
Deciding
on Where to Install the Air Conditioner
◆ Piping outside diameter
◆ RJ070/080F4HX**/AJ070/080FCJ4**
Indoor unit
Outdoor unit
Power supply Ø, V, Hz
**020/023/026/
030/035/052/
07/09/12/18/24**
RJ070F4HX**
RJ080F4HX**
AJ070FCJ4**
AJ080FCJ4**
1,220-240,50/60
Unit
Outside diameter
Liquid
Gas
**020/023/026/
030/035/07/09/12**
**052/18**
3/8"
1/4"
**24**
※ **24** model is connectable to only an 8Kw
outdoor unit.
1/2"
5/8"
CAUTION
3 m as minimum pipe length: It will reduce noise and
vibration.
200 mm
or more
100 mm
or more
160 mm or more
(h)
600 mm
minimum
300 mm
minimum
A
B
C
D
300 mm
minimum
600 mm
minimum
Main power switch
※ The appearance of the unit may be different from the diagram depending on the model.
◆ Piping length and the height
Dimension
Composition
1 Room max
length
25m
A, B,C,D
4 Room total max
length
70m
A+B+C+D
Max height between
Max height between
indoor unit & outdoor unit
indoor units
15m
7.5m
(H)
(h)
Make at least one round:
It will reduce noise and vibration
※ The appearance of the unit may be different from the diagram depending on the model.
8
(H)
Space Requirements for Outdoor Unit
When installing 1 outdoor unit
1500 or more
※ When the air outlet is towards the wall
2000 or more
600 or more
※ The upper part of the outdoor unit and the air
outlet is towards the wall
300 or more
1500 or more
600 or more
※ When 3 sides of the outdoor unit are blocked
by the wall
300 or more
300 or more
1500 or more
300 or more
※ When the air outlet is opposite the wall
ENGLISH
300 or more
(Unit : mm)
※ The upper part of the outdoor unit and the
air outlet is opposite the wall
※ When front and rear side of the outdoor unit is
towards the wall
When installing more than 1 outdoor unit
1500 or more
(Unit : mm)
※ When the air outlet is towards the wall
9
Deciding
on Where to Install the Air Conditioner
A
When installing more than 1 outdoor unit
300 or more
(Unit : mm)
600 or more
300 or more
600 or more
600 or more
1500 or more
300 or more
600 or more
600 or more
※ When 3 sides of the outdoor unit are blocked by the wall
※ When front and rear side of the outdoor unit is towards the wall
10
500 or more
300 or more
500 or more
1500 or more
600 or more
3000 or more
※ When front and rear side of the outdoor unit is towards the wall
300 or more
3000 or more
300 or more
※ The upper part of the outdoor unit and the air outlet is opposite the wall
Air
A conditioner and accessories
The following accessories are supplied with the air conditioner.
Accessories in the Outdoor Unit Case
3-wire
Power Cable
(option)
2-wire
Assembly Cable
(option)
Drain Plug
Energy Label
Rubber Leg
Flare Bolt
(Nut 12.70mm;Bolt
9.52mm) (except RJ040F2HX** , AJ040FCJ2**)
Installation
Manual
Flare Nuts, 9.52mm
outer pipe diameter
(except RJ040F2HX**
, AJ040FCJ2**)
※ Attach Energy Label to the outdoor unit properly when installing.
◆ RJ070F4HX**/RJ080F4HX**/AJ070FCJ4**/AJ080FCJ4**
3-wire
Power Cable
(option)
2-wire
Assembly Cable
(option)
Drain Plug
Flare Bolt
(Nut
12.70mm;Bolt
9.52mm)
Flare Bolt
(Nut 12.70mm; Bolt
15.88mm)(RJ080F4HX**, AJ080FCJ4**)
Energy Label
Installation
Manual
Flare Nuts, 15.88mm
outer pipe diameter Flare Nuts, 9.52mm
(RJ080F4HX**, outer pipe diameter
AJ080FCJ4**)
Rubber Leg
※ Attach Energy Label to the outdoor unit properly when installing.
䭭
The 3-wire power cable and the 2-wire assembly cable are optional. If these cables are not supplied,
use the standard cable approved by IEC standard.
Please, check “Connecting the Cables to the Outdoor Unit” section.
Installing and connecting the drain hose of the outdoor unit
While heating, ice may accumulate. During the process of
defrosting, check if condensation draining is adequate. For
adequate draining, do the following:
1. Insert the drain plug into the drain hole on the
underside of the outdoor unit.
2. Connect the drain hose to the drain plug.
$RAINHOLE
Drain hole
3. Ensure that condensation draining is adequate.
11
ENGLISH
◆ RJ040F2HX**/RJ050F2HX**/RJ052F3HX**/RJ060F3HX**/AJ040FCJ2**/AJ050FCJ2**/AJ052FCJ3**/AJ068FCJ3**
Cutting/extending the piping
A
1. Make sure that you have the required tools available (pipe cutter, reamer,flaring tool and pipe holder).
2. If you wish to shorten the piping, cut it using a pipe cutter, taking care toensure that the cut edge remains at a 90° angle with the side of
the pipe,and referring to the illustrations below for examples of edges cut correctlyand incorrectly.
Oblique
Rough
Burr
3. To prevent any gas from leaking out, remove all burrs at the cut end of thepipe, using a reamer.
4. Slide a flare nut on to the pipe and modify the flare.
Outer Diameter (D)
Thickness
Depth (A)
ø6.35 mm(1/4")
0.8mm
1.3 mm
ø9.52 mm(3/8")
0.8mm
1.8 mm
ø12.70 mm(1/2")
0.8mm
2.0 mm
ø15.88 mm(5/8")
0.8mm
2.2 mm
5. Check that the flaring is correct, referring to the illustrations below for examples of incorrect flaring.
Correct
Inclined
Damaged
Surface
Cracked
Uneven
Thickness
6. Align the pipes to be connected and tighten the flare nuts first manually andthen with a torque wrench, applying the following torque.
Outer Diameter (D)
Thickness
Torque (kgf·cm)
ø6.35 mm(1/4")
0.8mm
140~170
ø9.52 mm(3/8")
0.8mm
250~280
ø12.70 mm(1/2")
0.8mm
380~420
ø15.88 mm(5/8")
0.8mm
440~480
7. For further details on how to connect up to the outdoor unit and purge the circuit, refer to page 19.
䭭
In case welding the pipe, the gas nitrogen must be blown into the parts.
Connecting the cables to the outdoor unit
4FMFDUJOHDPNQSFTTFESJOHUFSNJOBM
4JMWFSTPMEFS
#
%
E
& ' E
U
/PSNJOBM /PSNJOBM
EJNFOTJPOT EJNFOTJPOT 4UBOEBSE
4UBOEBSE
4UBOEBSE
4UBOEBSE
GPSDBCMF GPSTDSFX EJNFOTJPO "MMPXBODF EJNFOTJPO "MMPXBODF EJNFOTJPO "MMPXBODF .JO .JO .BY EJNFOTJPO "MMPXBODF .JO
NN
NN
NN
NN
NN
NN
NN
NN
NN
NN
œ
œ
œ
œ œ
œ
t *ODBTFPGFYUFOEJOHUIFFMFDUSJDXJSFQMFBTF%0/05VTFBSPVOETIBQFEQSFTTJOHTPDLFU
*ODPNQMFUFXJSFDPOOFDUJPOTDBODBVTFFMFDUSJDTIPDLPSBmSF
12
A
Connecting the cables to the outdoor unit
◆ RJ040F2HX**/RJ050F2HX**/AJ040FCJ2**/AJ050FCJ2**
A-unit
1
2(N)
F2
2
F1
Earth
terminal
B
1
F1
2
F1
1(L)
F2
1
Assembly cable
C
B
F2
1
Earth
terminal
2(N)
F1
F2
2
F1
Earth
terminal
ENGLISH
1(L)
B-unit
Indoor unit
F2
C
2
F1
F2
Earth
terminal
Outdoor unit
L
N
Power cable to indoor units
!
"
#
Cable Type : A
Cable Type : B
Cable Type : C
A
L
N
1
2
F1 F2
Main Power
Supply cable
B
A
Earth
terminal
Communication cable
to indoor units
Specification for circuit breaker and power supply cord
䭭 Power supply cord is not supplied with air conditioner.
䭭 Select the power supply cord in accordance with relevant local and national regulations.
䭭 Wire size must comply with the applicable local and national code.
䭭 Specifications for local wiring power supply cord and branch wiring are in compliance with local cord.
Outdoor Units
Maximun Input Current[A]
Model
Rated
Outdoor
Indoor(Max.)
Outdoor Unit Indoor Unit
Hz
Volts
RJ040F2HX**
2 Room
50
1phase,220-240
9
0.8
AJ040FCJ2**
RJ050F2HX**
2 Room
50
1phase,220-240
11
0.8
AJ050FCJ2**
Power Supply
Total
MCA
MFA
9.8
9.8
11.25
11.8
11.8
13.75
Notes
1. Power supply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene sheathed flexible cord.
(Code designation IEC:60245 IEC 57 / CENELEC:H05RN-F)
2. Select power supply cord based on MCA.
3. MFA is used to select the circuit breaker and the ground fault circuit interrupter (earth leakage circuit breaker).
4. MCA represents maximum input current.
5. MFA represents capacity which may accept MCA.
6. The total length of the communication wire must not exceed 60m.Exceeding 60m may not satisfy the EN55014-1 standard.
7. Communication Cable Specification : 2G, 0.75mm², or more.
Abbreviations
- MCA : Min. Circuit Amps. (A)
- MFA : Max. Fuse Amps. (A)
Screw
Tighten Torque(kgf.cm)
Position
M4
12.0~15.0
1(L),2(L),L,N,F1,F2
Tightening power terminal
䭭 Connect the cables to the terminal board using the compressed ring terminal.
䭭 Use rated cables only.
䭭 Connect the cables with driver and wrench that can apply the rated torque to the screws.
䭭 Make sure that appropriate tightening torque is applied for cable connection. If the terminal is loose, arc heat may occur
and cause fire and if the terminal is connected too firmly, terminal may get damaged.
13
A
Connecting
the cables to the outdoor unit
◆ RJ052F3HX**/RJ060F3HX**/AJ052FCJ3**/AJ068FCJ3**
B-unit
A-unit
1(L) 2(N)
F1
1(L) 2(N)
F2
F1
C-unit
Indoor unit
F2
1(L) 2(N)
F1
F2
Assembly cable
1
2
F1
F2
1
2
F1
B
1
C
2
1
F2
2
Earth
terminal
Earth
terminal
F1
B
F2
1
C
2
F1
B
1
F2
F2
C
2
F1
F2
Earth
terminal
Earth
terminal
Earth
terminal
F1
Earth
terminal
Outdoor unit
1(L) 2(N) 1(L) 2(N)
L
N
1
2
A F1 F2 F1 F2
Main Power
Supply cable
B
Power cable to indoor units
!
"
#
A
Cable Type : A
Cable Type : B
Cable Type : C
c
Communication cable
to indoor units
Earth
terminal
Specification for circuit breaker and power supply cord
䭭 Power supply cord is not supplied with air conditioner.
䭭 Select the power supply cord in accordance with relevant local and national regulations.
䭭 Wire size must comply with the applicable local and national code.
䭭 Specifications for local wiring power supply cord and branch wiring are in compliance with local cord.
Model
Outdoor Unit
RJ052F3HX**
AJ052FCJ3**
RJ060F3HX**
AJ068FCJ3**
Indoor Unit
Outdoor Units
Rated
Hz
Volts
Maximun Input Current[A]
Power Supply
Outdoor
Indoor(Max.)
Total
MCA
MFA
3 Room
50
1phase,220-240
11
1.2
12.2
12.2
13.75
3 Room
50
1phase,220-240
13
1.4
14.4
14.4
16.25
3 Room
50
1phase,220-240
14
1.5
15.5
15.5
17.5
Notes
1. Power supply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene sheathed flexible cord.
(Code designation IEC:60245 IEC 57 / CENELEC:H05RN-F)
2. Select power supply cord based on MCA.
3. MFA is used to select the circuit breaker and the ground fault circuit interrupter (earth leakage circuit breaker).
4. MCA represents maximum input current.
5. MFA represents capacity which may accept MCA.
6. Communication Cable Specification : 2G, 0.75mm², or more.
Abbreviations
- MCA : Min. Circuit Amps. (A)
- MFA : Max. Fuse Amps. (A)
Tightening power terminal
Screw
Tighten Torque(kgf.cm)
Position
M4
12.0~15.0
1(L),2(L),L,N,F1,F2
䭭 Connect the cables to the terminal board using the compressed ring terminal.
䭭 Use rated cables only.
䭭 Connect the cables with driver and wrench that can apply the rated torque to the screws.
䭭 Make sure that appropriate tightening torque is applied for cable connection. If the terminal is loose, arc heat may occur
and cause fire and if the terminal is connected too firmly, terminal may get damaged.
14
◆ RJ070F4HX**/RJ080F4HX**/AJ070FCJ4**/AJ080FCJ4**
A-unit
B-unit
C-unit
D-unit
Indoor unit
F1
F2
1(L) 2(N)
F1
F2
1(L) 2(N)
F1
F2
1(L) 2(N)
F1
ENGLISH
1(L) 2(N)
F2
Assembly cable
1 2
F1 F2
1 2
B
1
F1 F2
B
1 2
C
B
F1 F2
1
F1 F2
Earth
terminal
C
2
Earth
terminal
Earth
terminal
1 2
F1 F2
Earth
terminal
Earth
terminal
C
2
1 2
F1 F2
Earth
terminal
B
C
1 2
F1 F2
Earth
terminal
F1 F2
Earth
terminal
Outdoor unit
1(L) 2(N) 1(L) 2(N)
Power cable to indoor units
!
"
#
Cable Type : A
Cable Type : B
Cable Type : C
L
N
1
2
A
Main Power
Supply cable
Earth
terminal
A F1 F2 F1 F2
C
B
D
Communication cable
to indoor units
Specification for circuit breaker and power supply cord
䭭 Power supply cord is not supplied with air conditioner.
䭭 Select the power supply cord in accordance with relevant local and national regulations.
䭭 Wire size must comply with the applicable local and national code.
䭭 Specifications for local wiring power supply cord and branch wiring are in compliance with local cord.
Outdoor Units
Maximun Input Current[A]
Model
Rated
Outdoor
Indoor(Max.)
Outdoor Unit Indoor Unit
Hz
Volts
RJ070F4HX**
4 Room
50
1phase,220-240
16.6
2.1
AJ070FCJ4**
RJ080F4HX**
4 Room
50
1phase,220-240
16.6
2.1
AJ080FCJ4**
Power Supply
Total
MCA
MFA
18.7
18.7
20.75
18.7
18.7
20.75
Notes
1. Power supply cords of parts of appliances for outdoor use shall not be lighter than polychloroprene sheathed flexible cord.
(Code designation IEC:60245 IEC 57 / CENELEC:H05RN-F)
2. Select power supply cord based on MCA.
3. MFA is used to select the circuit breaker and the ground fault circuit interrupter (earth leakage circuit breaker).
4. MCA represents maximum input current.
5. MFA represents capacity which may accept MCA.
6. Communication Cable Specification : 2G, 0.75mm², or more.
Abbreviations
- MCA : Min. Circuit Amps. (A)
- MFA : Max. Fuse Amps. (A)
Screw
Tighten Torque(kgf.cm)
Position
M4
12.0~15.0
1(L),2(L),L,N,F1,F2
Tightening power terminal
䭭 Connect the cables to the terminal board using the compressed ring terminal.
䭭 Use rated cables only.
䭭 Connect the cables with driver and wrench that can apply the rated torque to the screws.
䭭 Make sure that appropriate tightening torque is applied for cable connection. If the terminal is loose, arc heat may occur
and cause fire and if the terminal is connected too firmly, terminal may get damaged.
15
TAransmitter installation(optional)
◆ RJ040F2HX**/RJ050F2HX**/RJ052F3HX**/RJ060F3HX**/RJ070F4HX**/RJ080F4HX**
AJ040FCJ2**/AJ050FCJ2**/AJ052FCJ3**/AJ068FCJ3**/AJ070FCJ4**/AJ080FCJ4**
Accessories (Transmitter: MIM-B13A)
Transmitter
MAIN
485
DC Power Cable DC Power Cable Communication
Transmitter SUB Communication
(12V)
(5V)
Cable
Cable
Cable Tie
R2 R1 R2 R1
R1 R2
1.
Turn the power off and take off the cover of the outdoor units.
2.
Fix the case with bolts to the side of the control box referring to
the figure on the right side.
In case of FJM outdoor unit, there is not enough space to fix all
parts of transmitter. So you may use transmitter main PCB.
3.
Attach the transmitter main PCB to the case, then connect F1/
F2 lines, R1/R2 lines which are upper controller communication
cables and DC 12V power cables to the interface module referring
to the figure on page 17. (Upper controller power should be off.)
RJ040F2HX**/RJ050F2HX**
AJ040FCJ2**/AJ050FCJ2**
Transmitter
4.
RJ052F3HX**/AJ052FCJ3**
You must check the position of dip switch on the transmitter's
main PCB and the main PCB of MH**/NJ** indoor units. For AQV**/
AJN**/AR** indoor units, refer to page 30.
Transmitter
5.
Assemble a cover of the outdoor unit and turn the power on.
RJ060F3HX**/RJ070F4HX**/RJ080F4HX**
AJ068FCJ3**/AJ070FCJ4**/AJ080FCJ4**
6.
Check the communication status.
7.
If you install a transmitter to the outdoor unit, every indoor unit
which is connected to the outdoor unit can be controlled simultaneously.
8.
Each outdoor unit connected to the same centralized controller
has its own transmitter.
Transmitter
Fix the case with hinges
(Control Box in the outdoor unit)
16
Case
DC 12V (Blue)
ENGLISH
DC 12V (Blue)
DC 12V
supply
3 3
Transmitter MAIN PCB
RJ052F3HX**/RJ060F3HX**
RJ070F4HX**/RJ080F4HX**
AJ052FCJ3**/AJ068FCJ3**
AJ070FCJ4**/AJ080FCJ4**
RJ040F2HX**/RJ050F2HX**
Outdoor unit PCB AJ040FCJ2**/AJ050FCJ2**
F1 F2 F1 F2
L
N
F1 F2
1(L) 2(N) 1(L) 2(N)
Terminal Block in the outdoor unit
RJ052F3HX**/RJ060F3HX**
RJ070F4HX**/RJ080F4HX**
AJ052FCJ3**/AJ068FCJ3**
L
N
L
N
Terminal Block in the outdoor unit
RJ040F2HX**/RJ050F2HX**
AJ040FCJ2**/AJ050FCJ2**
AJ070FCJ4**/AJ080FCJ4**
K1 K2 K3 K4
Check the dip switch postion on transmitter main PCB
as the picture above, "turn ON"
Change DIPswitch-K2 on
MH**/NJ** indoor units PCB
(K2 : ON → OFF). For AQV**/AJN**/AR**
indoor units,refer to page 30.
17
Checking correct earthing
A
If the power distribution circuit does not have an earth or the earth does not comply with specifications, an
earthing electrode must be installed. The corresponding accessories are not supplied with the air conditioner.
Select an earthing electrode that complies with the specifications
given in the illustration opposite.
2.
Determine a suitable location for the earthing electrode:
◆ In damp hard soil rather than loose sandy or gravel soil that has a
higher earthing resistance.
◆ Away from underground structures or facilities, such as gas pipes,
water pipes, telephone lines and underground cables.
◆ At least two meters away from a lightening conductor earthing
electrode and its cable.
䭭 The earthing wire for the telephone line cannot be used to earth the
air conditioner.
3.
Dig a hole of the size indicated in the illustration opposite, drive the
earthing electrode into position and cover the top of the electrode with
the excavated soil.
4.
Install a green/yellow insulated earthing wire (Ø1.6 mm, section 2 mm² or
greater):
◆ If the earthing wire is too short, connect an extension lead, soldering
the connec tion and wrapping it with insulating tape (do not bury the
soldered connection)
◆ Secure the earthing wire in position with staples If the earthing
electrode is installed in an area of heavy traffic, its wire must be
connected securely
5.
Carefully check the installation, by measuring the earthing resistance
with an earthing resistance tester. If the resistance is above the required
level(Example:100Ω), drive the earthing electrode deeper into the ground
or increase the number of earthing electrodes.
6.
Connect the earthing wire to the earthing screw on the air conditioner.
Carbon
plastic
Steel core
PVC-insulated green To earthing
screw
/yellow wire, 2mm² x 3.5 m
50 cm
30 cm
1.
Fixing the unit in position
1.
Position the outdoor unit so that the air flow is directed towards the
outside, as indicated by the arrows on the top of the unit.
2.
Attach the outdoor unit to the appropriate support using anchor bolts.
◆ The earthing wire for the telephone line cannot be used to earth the air
conditioner.
3.
DIf the outdoor unit is exposed to strong winds, install shield plates
around the outdoor unit, so that the fan can operate correctly.
䭭 Certainly fix up its rubber leg in order to prevent its vibration and noise.
OUTDOOR UNIT INSTALLED ON THE WALL BY RACK
- Ensure the wall will be able to suspend the weight of rack and outdoor unit ;
- Install the rack close to the colum as much as possible;
- Install proper grommet in order to reduce noise and residual vibration
transferred by outoor unit towards wall.
'Y’ mm
The outdoor unit must be installed on a rigid and stable base to avoid any increase in the noise level and
vibration, particularly if the outdoor unit is to be installed close to a neighbour.
If it is to be installed in a location exposed to strong winds or at a height, the unit must be fixed to an
‘X’ mm
appropriate support (wall or ground).
Rubber leg
Model
RJ040F2HX**/RJ050F2HX**
AJ040FCJ2**/AJ050FCJ2**
RJ052F3HX** /RJ060F3HX**
RJ070F4HX**/RJ080F4HX**
AJ052FCJ3**/AJ068FCJ3**
AJ070FCJ4**/AJ080FCJ4**
Y
612
317
660
340
Designed to cut off
residual vibration
from outdoor unit to
rack. (not supplied
with product)
Soft rubber designed to cut off
vibration from rack to wall.
(not supplied with product)
18
X
Connecting up and purging the circuit
A
WARNING
The outdoor unit is loaded with sufficient R410A refrigerant.Do not vent R-410A into atmosphere: it is a fluorinated greenhouse
gas, covered by Kyoto Protocol, with a Global Warming Potential (GWP) = 1975.
You should purge the air in the indoor unit and in the pipe.
If air remains in the refrigerant pipes, it affects the compressor. It may cause reduction of cooling capacity and malfunction.
Refrigerant for air purging is not charged in the outdoor unit. Use Vacuum Pump as seen in the picture.
◆ RJ040F2HX**/RJ050F2HX**/RJ052F3HX**/AJ040FCJ2**/
AJ050FCJ2**/AJ052FCJ3**
1 Check the piping connections.
2 Connect the charging hose of low pressure side of manifold gauge to
the packed valve having a service port (RJ040F2HX**/AJ040FCJ2** :
3/8” service valve 2EA; RJ050F2HX** /AJ050FCJ2**: 3/8” service valve
1EA+1/2” service valve 1EA; RJ052F3HX**/AJ052FCJ3** : 3/8” service
valve 2EA+1/2” service valve 1EA) as shown at the figure.
Indoor
A-unit
Indoor
B-unit
WARNING
◆ Make the electrical connection and leave the system into “stand by
mode”. Do not turn on the system! This is necessary for better
vacuum operation (full OPEN position of Electronic Expansion
Valve - EEV -).
Vacuum
Pump
3 Open the valve of the low pressure side of manifold gauge
counter-clockwise.
4 Purge the air from the system using vacuum pump for about 10
minutes.
- Close the valve of the low pressure side of manifold gauge clockwise.
- Make sure that pressure gauge show -0.1MPa(-76cmHg) after about 10
minutes.
This procedure is very important in order to avoid gas leak.
- Turn off the vacuum pump
- Remove the hose of the low pressure side of manifold gauge.
5 Set valve cork of both liquid side and gas side of packed valve to
the open position.
Valve stem
Stem cap
Service port
6 Mount the valve stem nuts and the service port cap to the valve,
BOEUJHIUFOUIFNBUUIFUPSRVFPGLHGtDNXJUIBUPSRVFXSFODI
7 Check for gas leakage.
- At this time, especially check for gas leakage from the 3-way valve’s stem
nuts, and from the service port cap.
19
ENGLISH
When installing, make sure there is no leakage. When recovering the refrigerant, ground the compressor first before
removing the connection pipe. If the refrigerant pipe is not properly connected and the compressor works with the service
valve open, the pipe inhales the air and it makes the pressure inside of the refrigerant cycle abnormally high. It may cause
explosion and injury.
A
Connecting up and purging the circuit
◆ RJ060F3HX**/RJ070F4HX**/RJ080F4HX**/AJ068FCJ3**/
AJ070FCJ4**/AJ080FCJ4**
1 Check the piping connections.
2 Connect the charging hose of low pressure side of manifold gauge to the
packed valve having a service port (5/8” Packed valve) as shown at the
figure (Value stem: 1/2” - 20UNF).
WARNING
◆ Make the electrical connection and leave the system into “stand
by mode”. Do not turn on the system! This is necessary for better
vacuum operation (full OPEN position of Electronic Expansion
Valve - EEV -).
A
B
C
Vacuum
Pump
3 Open the valve of the low pressure side of manifold gauge
counter clockwise.
4 Purge the air from the system using vacuum pump for about 30 minutes.
- Close the valve of the low pressure side of manifold gauge clockwise.
- Make sure that pressure gauge show -0.1MPa(-76cmHg) after about
30 minutes. This procedure is very important in order to avoid gas leak.
- Turn off the vacuum pump.
- Remove the hose of the low pressure side of manifold gauge.
5 Set valve cork of both liquid side and gas side of packed valve to the
open position.
6 Mount the valve stem nuts and the service port cap to the valve, and
UJHIUFOUIFNBUUIFUPSRVFPGLHGtDNXJUIBUPSRVFXSFODI
7 Check for gas leakage.
- At this time, especially check for gas leakage from the 3-way valve’s
stem nuts, and from the service port cap.
Adding refrigerant
If you install the excessive length of pipe, add additional refrigerant as 10g(20g) per unit meter ;
refer to the table below.
Refer to the Service Manual for more details on this operation.
Model
Total connecting pipe length (L)
Adding refrigerant
RJ040F2HX**
AJ040FCJ2**
LTd15m
LT>15m
LTd20m
LT>20m
LTd30m
Chargeless
(LT- 15m)x10g
Chargeless
(LT- 20m)x20g
Chargeless
LT>30m
(LT- 30m)x10g
LTd40m
Chargeless
LT>40m
(LT- 40m)x10g
RJ050F2HX**
AJ050FCJ2**
RJ052/060F3HX**
AJ052/068FCJ3**
RJ070/080F4HX**
AJ070/080FCJ4**
$IBSHJOHUIFSFGSJHFSBOUVOEFSDPOEJUJPOTPGMJRVJECZVTJOHBMJRVJEQJQF
3"JTBNJYFEUZQFPGSFGSJHFSBOU*UJTOFDFTTBSZGPSSFDIBSHJOHVOEFSDPOEJUJPOTPGMJRVJE8IFOSFDIBSHJOHSFGSJHFSBOUGSPN
UIFSFGSJHFSBOUDZMJOEFSUPUIFFRVJQNFOUGPMMPXUIFJOTUSVDUJPOTCFMPX
#FGPSFSFDIBSHJOHDIFDLXIFUIFSUIFDZMJOEFSIBTBTJQIPOPSOPU
5IFSFBSFUXPXBZTUPSFDIBSHFUIFSFGSJHFSBOU
$ZMJOEFSXJUITJQIPO
$ZMJOEFSXJUIPVUTJQIPO
TJQIPO
f$IBSHFUIFSFGSJHFSBOUTUBOEJOHUIF
DZMJOEFSVQSJHIU
f$IBSHFUIFSFGSJHFSBOUUVSOJOHUIFDZMJOEFS
VQTJEFEPXO
t *G3"SFGSJHFSBOUJTDIBSHFEXJUIHBTUIFDPNQPTJUJPOPGUIFDIBSHFESFGSJHFSBOUDIBOHFTBOEUIF
DIBSBDUFSJTUJDTPGUIFFRVJQNFOUWBSZ
t %
VSJOHUIFNFBTVSJOHPQFSBUJPOPGSFGSJHFSBOURVBOUJUZBEEFEVTFBOFMFDUSPOJDCBMBODF
*GDZMJOEFSEPFTOUIBWFTZQIPOVQTFUJU
20
Valve stem
Stem cap
Service port
A
Adding
refrigerant
Important information regulation regarding the refrigerant used
CAUTION :
Inform user if system contains 3 kg or more of fluorinated greenhouse gases.
In this case, it has to be checked for leakage at least once every 12 months,
according to regulation n¢X842/2006. This activity has to be covered by
qualified personnel only.
In case situation above (3 kg or more of R-410A), installer (or recognised
person which has responsability for final check) has to provide a
maintenance book, with all the information recorded according to
REGULATION (EC) N¢X 842/2006 OF THE EUROPEAN PARLIAMENT AND OF
THE COUNCIL of 17 May 2006 on certain fluorinated greenhouse gases.
Please fill in with indelible ink,
- ① the factory refrigerant charge of the product,
- ② the additional refrigerant amount charged in the field and
- ①+② the total refrigerant charge.
on the refrigerant charge label supplied with the product.
Note
a. Factory refrigerant charge of the product: see unit name plate
b. Additional refrigerant amount charged in the field
(Refer to the above information for the quantity of
refrigerant replenishment.)
c. Total refrigerant charge
d. Refrigerant cylinder and manifold for charging
䭭 The filled-out label must be adhered in the proximity of the product
charging port (e.g. onto the inside of the stop valve cover).
Refrigerant type
GWP value
R410A
1975
ENGLISH
This product contains fluorinated greenhouse gases covered by
the Kyoto Protocol. Do not vent gases into the atmosphere.
※ GWP=Global Warming Potential
Contains fluorinated greenhouse gases
covered by the Kyoto Protocol.
Indoor unit

d
a
= (
= (

Outdoor unit
) kg
) kg
+ = (
b
) kg
c
Performing leak tests
Before completing the installation (insulation of the cables, hose and
piping and fixing of the indoor unit to the installation plate), you
must check that there are no gas leaks.
To check for gas leaks on the...
Then, using a leak detector,check the ...
Indoor unit
Outdoor unit
Flare nuts at the end of sections C and D.
Valves on sections A and B.
C
D
LEAK TEST WITH NITROGEN (before opening valves)
In order to detect basic refrigerant leaks, before recreating the vacuum and
recirculating the R-410A, it’s responsable of installer to pressurize the whole system
with nitrogen (using a cylinder with pressure reducer) at a pressure above 30 bar
(gauge).
LEAK TEST WITH R-410A (after opening valves)
Before opening valves, discharge all the nitrogen into the system and create vacuum
according to page 19 ~20.
After opening valves, check leaks using a leak detector for refrigerant.
21
A
Performing
leak tests
PUMP DOWN (before disconnecing t the refrigerant connections for unit repair,
removal or disposal)
Pump-down is an operation intended to collect all the system refrigerant in the outdoor unit.
This operation must be carried out before disconnecting the refrigerant pipe in order to avoid
refrigerant loss to the atmosphere.
- Shut off all the liquid valve with the Allen wrench.
- Turn the system on in cooling with fan operating at high velocity.
(Compressor will immediately start, provided 3 minutes have elapsed since the last stop).
- After 2 minutes of operation, shut down the suction valves with the same wrench.
- Turn the system off and switch mains supply off.
- Disconnect pipes. After disconnection, protect valves and tubing ends from dust.
- Compressor damage may occur if run at a negative suction pressure.
RJ040F2HX**
RJ050F2HX**
AJ040FCJ2**
AJ050FCJ2**
$
RJ052F3HX**
AJ052FCJ3**
RJ060F3HX**
AJ068FCJ3**
$
%
&
※ The designs and shape are subject to change according to the model.
RJ070F4HX**
RJ080F4HX**
AJ070FCJ4**
AJ080FCJ4**
$
%
&
Pipe installation with indoor units
Follow different orders depending on the capacity of indoor units.
OUTDOOR UNIT
<MH020/023/026/030/035F***/NJ026/035**/AQV07/09/12**/
AR07/09/12**>
ŹInstall pipes between indoor and outdoor units orderly as[A→B→C→D].
◆ RJ050F2HX**/RJ052F3HX**/AJ068FCJ3**
<MH052F***/AQV18**/AR18**>
A unit
ŹInstall pipes between indoor and outdoor units orderly as [ B→C].
◆ RJ060F3HX**/RJ070F4HX**/RJ080F4HX**
AJ070FCJ4**/AJ080FCJ4**
<MH052F***/AQV18/24** /AR18/24**>
B unit
Ź Install pipes between indoor and outdoor units orderly as [ C→D].
K **24**model is connectable to only an 8Kw outdoor unit.
OUTDOOR UNIT
A unit
B unit
C unit
D unit
22
Setting an indoor unit address and installation option
A
RJ040F2HX**/RJ050F2HX**
AJ040FCJ2**/AJ050FCJ2**
CAUTION
ENGLISH
This product is prohibited one indoor unit installation. Don't use pipe
checking operation and Auto Addressing Mode when one indoor
unit is installed. 37 " to appear on the display of
◆ Switch the system on and wait for code "
the external unit (this requires approximately 60 seconds **).
"displays, press once the red button (K1) shown on
◆ As soon as code "
the figure on the side of the page:
WARNING
If the quantity of indoor units connected is lower than maximum
connectable to outdoor unit, the rotary switch SW01 has to be
positioned, in order to select a number equal to indoor units’
quantity you connected.
RJ052F3HX**/RJ060F3HX**/
RJ070F4HX**/RJ080F4HX**/
AJ052FCJ3**/AJ068FCJ3**/
AJ070FCJ4**/AJ080FCJ4**
◆ After the operations described above have been performed, the system starts in Cooling or
Heating mode, depending on the external ambient temperature. After a few minutes (from a
minimum of 3 to 5 minutes for the internal unit), the system stops automatically, completing
the self-test and addressing procedure.
"
" appears on the display of the external unit.
" (that confirms the correct execution
◆ 20 seconds after the display of "
of the procedure), the following codes (if four internal units are connected) dis
play in sequence on the display of the external unit:
Display 1
Display 2
Description
The outdoor unit is communication correctly together the
indoor unit connected to refrigerant pipe A.
The outdoor unit is communication correctly together the
indoor unit connected to refrigerant pipe B.
Display of the external unit
※ During the initial 60 seconds,
display 1 shows in sequence:
00→ 01→02 →...15→ 00...
The outdoor unit is communication correctly together the
indoor unit connected to refrigerant pipe C.
The outdoor unit is communication correctly together the
indoor unit connected to refrigerant pipe D.
At this point it is possible to start the internal units in the desired mode
䭭
If "
"doesn’t display, the procedure has failed and it is therefore necessary to read
ALL the operator’s manual before repeating the operating described in steps 1-2-3-4.
23
SAetting an indoor unit address and installation option
Step 1
Review all the following elements in the installation:
◆ Installation site strength
◆ Piping connection tightness to detect any gas leakage
◆ Connection wiring
◆ Heat-resistant insulation of the piping
◆ Drainage
◆ Earthing wire connection
Step 2
IMPORTANT!
Before selecting switch turn off the system power supply
RJ040F2HX**/RJ050F2HX**
AJ040FCJ2**/AJ050FCJ2**
- Select rotary switch “SW01” of outdoor unit display
PCB, according to number of indoor unit connected:
SW01
SW01
Switch
37 Indoor unit
address
ex)
ex)
connecting with 2 connecting with
4 indoor units.
indoor units.
Display of the external unit
Advise control we are going to proceeed with manual addressing as follow:
RJ052F3HX**/RJ060F3HX**/RJ070F4HX**/RJ080F4HX**
AJ052FCJ3**/AJ068FCJ3**/AJ070FCJ4**/AJ080FCJ4**
SW 02
Manual
addressing
Switch
Indoor unit
address
- Move dipswitch n°1 of “SW02 - outdoor
unit display PCB” down;
- For assigning new indoor unit address,
refer to page 26~28. (AQV 07/09/12/18/24****)
(AR 07/09/12/18/24***)
Move down the
switch n°1
Display of the external unit
Step 3
Follow of indication reported into table below for indoor unit addressing
Step 4
Turn on the system power supply and waiting for 60 seconds after estabilishing communication
between outdoor and indoor units.
During this phase, the left display of outdoor unit display PCB “DIS01” will count fom 00--01--02 to 15.
Estabilished communication the left display will count sequentially:
00--communication with indoor unit A;
01--communication with indoor unit B;
02--communication with indoor unit C;
03--communication with indoor unit D;
※ In case of Manual address mode,you can do pipe check operation for check whether you connect the pipes correctly or not.
But you need set indoor address switch yourselves.
24
TYPE
PICTURE
TO SET ADDRESSING MANUALLY BY
MODEL
ROTARY SWITCH “SW02”
Same for:
IT'S HERE!
ENGLISH
SERIE VISION
RAC
MH020FV(N/A)**
MH023FB**
MH026FB(V/N/A)**
MH035FB(V/N/A)**
MH052FB(V/N/A)**
MAIN
PCB
+
sw02
sw02
SLIM 1 WAY
MH026FS**
MH035FS**
MINI 4 WAY
MH030FM**
MH035FM**
MH052FM**
sw02
sw02
SW SLIM DUCT
MSP-DUCT
MH026FE**
MH035FE**
NJ026LHX**
NJ035LHX**
MH052FU**
CONSOLE
MH026FJ**
MH035FJ**
MAIN
PCB
+
25
Setting
an indoor unit address and installation option
A
ROTARY SWITCH “SW02” POSITION ACCORDING TO REFRIGERANT CIRCUIT CONNECTED ( 0=A; 1=B; 2=C; 3=D )
Indoor Unit
SW02
OUTDOOR UNIT
Indoor Unit
SW02
OUTDOOR UNIT
Att. "A"
Att. "A"
0
0
A unit
Att. "B"
A unit
1
B unit
Att. "B"
1
C unit
B unit
Att. "C"
2
Indoor Unit
SW02
Att. "A"
OUTDOOR UNIT
0
Att. "B"
1
A unit
Att. "C"
B unit
2
C unit
D unit
Att. "D"
3
INSTALLATION TEST MODE (with all indoor units functioning)
Please do cool mode try-run or heat mode try run.
Cool mode try-run : Push the [K2] button three times.
Heat mode try-run : Push the [K2] button once.
After 12 minutes of stationary condition check each indoor unit air treatment:
Cooling mode (indoor unit check) --> Inlet air temp. - Outlet air temp: From 10°K to 12°K ( indicative delta T)
Heating mode (indoor unit check) --> Outlet air temp. - Inlet air temp: From 11°K to 14°K (indicative delta T)
In heating mode, the indoor fan motor can remain off to avoid cold air blown into conditioned space.
26
Setting Option
(AQV**/AJN**/AR**)
Entering mode for
setting option
Option
setting mode
ENGLISH
Mode change
High Temp Button
High Fan Button
Low Temp Button
Low Fan Button
X Setting Option
1. Remove batteries from the remote controller
2. Insert batteries and enter the option setting mode while pressing High Temp button and Low Temp button.
3. Each time you press Low Fan button, 7-seg on left side is increased by “1” and each time you press High Fan button,
7-seg on right side is increased by “1”
4. You press
button to move to the next setteing page.
5. After setting option, press
button to check whether the option code you input is correct or not.
¤
¤
¤
¤
¤
¤
¤
¤
6. Press operation button
¤
with the direction of remote control for set.
t 4&(4&(4&(4&(BSFOPUTFUBTQBHFPQUJPO
t 4FUUIF4&(4&(BT0/TUBUVTBOE4&(4&(BT0''TUBUVT
EX) Set the each option separately since you cannot set the ADDRESS setting and indoor unit
installation setting option at the same time.
27
Setting an indoor unit address and installation option
A
The procedure of setting option
Operation
* Step 1
1. Remove the batteries from the remote controller.
2. Insert batteries while pressing High Temp Button and Low Temp Button.
* Step 2
1. Press Low Fan button to enter SEG2 value.
2. Press High Fan button to enter SEG3 value.
* Step 3
Press Mode button to be change to Cool mode in the ON status.
1. Press Low Fan button to enter SEG4 value.
2. Press High Fan button to enter SEG5 value.
* Step 4
Press Mode button to be changed to DRY mode in the ON status.
1. Press Low Fan button to enter SEG6.
2. Press High Fan button to enter SEG8.
* Step 5
Press Mode button to be changed to FAN mode in the ON status.
1. Press Low Fan button to enter SEG9 value.
2. Press High Fan button to enter SEG10 value.
* Step 6
Press Mode button to be changed to HEAT mode in the ON status.
1. Press Low Fan button to enter SEG11 value.
2. Press High Fan button to enter SEG12value
* Step 7
Press Mode button to be changed to AUTO mode in the OFF status.
1. Press Fan button to enter SEG14 value.
2. Press High Fan button to enter SEG15 value.
* Step 8
Press Mode button to be changed to Cool mode in the OFF status.
1. Press Low Fan button to enter SEG16 value.
2. Press High Fan button to enter SEG17 value.
* Step 9
Press Mode button to be changed to DRY mode in the OFF status.
1. Press Low Fan button to enter SEG18 value.
2. Press High Fan button to enter SEG20 value.
* Step 10
Press Mode button to be changed to FAN mode in OFF status
1. Press Low Fan button to enter SEG21 value.
2. Press High Fan button to enter SEG22 value.
* Step 11
Press Mode button to be changed to HEAT mode in the OFF status
1. Press Low Fan button to enter SEG23 value.
2. Press High Fan button to enter SEG24 value.
* Step 12
Press Mode button to check whether the option code you entered is correct or not.
Press operation button to enter option.
28
Indication
Setting an indoor unit address (MAIN/RMC)
ENGLISH
1. Check whether power is supplied or not.
- When the indoor unit is not plugged in, there should be additional power
supply in the indoor unit.
Indoor Unit
1(L)
2(N)
2. The panel(display ) should be connected to an indoor unit to receive option.
F2
F1
3. Before installing the indoor unit, assign an address to the indoor unit according
to the air conditioning system plan.
4. Assign an indoor unit address by wireless remote controller.
- The initial setting status of indoor unit ADDRESS(MAIN/RMC) is "0A0000-100000-200000-300000"
- There is no need to assign extra ADDRESS for 1:1 installation between indoor unit and outdoor unit.
Option No. : 0AXXXX-1XXXXX-2XXXXX-3XXXXX
Option
SEG1
SEG2
SEG3
Explanation
PAGE
MODE
Setting Main
address
SEG4
SEG5
SEG6
100-digit of indoor 10-digit of indoor
unit address
unit
A single digit of
indoor unit
Remote
Controller
Display
Indication Details Indication Details
Indication Details Indication
0
Indication
and Details
0
A
Option
SEG7
SEG8
Explanation
PAGE
Details
Indication
Details
100-digit
0~9
10-digit
Indication Details
No Main
address
Main
address
1
setting
mode
SEG9
0~9
SEG10
Setting RMC
address
0~9
A single
digit
SEG11
SEG12
Group
channel(*16)
Group address
Remote
Controller
Display
Indication Details Indication
Indication
and Details
Details
Indication Details
0
No RMC
address
1
RMC
address
setting
mode
1
Indication
Details Indication
RMC1
Details
Indication
Details
1~F
RMC2
1~F
※ You must set RMC address setting mode when using the centralized Control .
29
ASetting an indoor unit address and installation option
t8IFOi"w_w'wJTFOUFSFEUP4&(_UIFJOEPPSVOJU."*/"%%3&44JTOPUDIBOHFE
t*GZPVTFUUIF4&(BTUIFJOEPPSVOJUXJMMNBJOUBJOUIFQSFWJPVT."*/"%%3&44FWFOJGZPVJOQVUUIFPQUJPOWBMVFPG4&(_
t*GZPVTFUUIF4&(BTUIFJOEPPSVOJUXJMMNBJOUBJOQSFWJPVT3.$"%%3&44FWFOJGZPVJOQVUUIFPQUJPOWBMVFPG4&(_
5. The MAIN address is for commnication between the indoor unit and the outdoor unit. Therefore, you must set it to
operate the air conditioner properly.
Setting an indoor unit installation option (suitable for the condition of each installation location)
1. Check whether power is supplied or not.
- When the indoor unit is not plugged in, there should be additional power
Indoor Unit
supply in the indoor unit.
1(L)
2(N)
2. The panel(display ) should be connected to an indoor unit to receive option.
F2
F1
3. Before installing the indoor unit, assign an option to the indoor unit according
to the air conditioning system plan.
- The default setting of an indoor unit installation option is “02000-100000-200000-300000”.
- Individual control of a remote controller(SEG20) is The function that controls an indoor unit individually when there is
more than one indoor unit.
4. Set the indoor unit option by wireless remote controller.
- When entering Address option, connect remote controller receiver.
Option
Explanation
SEG1
PAGE
SEG2
MODE
Indication Details Indication
Details
SEG3
Indication
SEG4
Details
Indication Details Indication
Indication and Details
Option
Explanation
0
2
0
0
SEG7
PAGE
SEG8
SEG9
SEG10
Indication Details Indication
Indication and Details
1
Details
Indication
0
Details
0
SEG16
Option
SEG13
SEG14
SEG15
PAGE
External control
External control output
Indication Details Indication
Indication and Details
2
Option
SEG19
Explanation
PAGE
Details
0
No use
1
On/Off control
2
3
Off control
Window On/Off control1)
SEG20
Indication Details Indication
Details
Indication
Details
0
Thermo ON
Details Indication Details
0
1
No use
Use
SEG11
Details Indication Details
0
Slave
0
1
Master
SEG17
SEG18
Buzzer
Indication Details Indication
Details Indication Details
0
Operation ON
SEG21
Indication
Details
0
SEG12
Master / Slave
Use
0
1
SEG6
Indication Details Indication
0
Explanation
SEG5
Central control
0
1
SEG22
No Use
SEG23
Indication Details Indication
SEG24
Details Indication Details
Indication and Details
3
0
0
0
0
0
▶ If you input a number other than 0~4 of the individual control of the indoor unit(SEG20), the indoor is set as "indoor 1".
1) The window on/off function applies to the following unit
- AJN**/AR**
30
It could take maximum 60 minutes to operate for the protection of the compressor. if the outdoor
temperature is below -5°C.
ENGLISH
Ampere Limit Setting & Changing Procedure
WARNING
◆ Do not adjust the “Ampere Limit Switch”, if it’s not necessary :
before modifying it, evaluate the total number of electric and electronics
loads consumption and use “Ampere limits switch” just as
emergency solution or in case the system is anyway oversized compared to
real thermal load needed.
◆ “Ampere Limit Switch” is initially set to the default value (table below).
◆ “Ampere Limit Switch” is on the PCB of outdoor unit.
◆ Contact the authorized service technician or dealer for setting and changing
the “Ampere Limit Switch”.
◆ Before changing the “Ampere Limit Switch”, turn off the main power of the
system.
RJ070F4HX**
RJ040F2HX** RJ050F2HX** RJ052F3HX**
RJ080F4HX**
RJ060F3HX** AJ068FCJ3**
AJ040FCJ2** AJ050FCJ2** AJ052FCJ3**
AJ070FCJ4**
AJ080FCJ4**
11.0A
(Default)
11.0A
(Default)
13.0A
(Default)
RJ040F2HX**/RJ050F2HX**
AJ040FCJ2**/AJ050FCJ2**
Switch
Selection
Ampere
9.0A
(Default)
※ The designs and shape are subject to
change according to the model.
14.0A
(Default)
Switch
16.6A
(Default)
3
4
ON
ON
(OFF)
8.5A
9.0A
10.5A
13.0A
13.0A
14.0A
ON
OFF
OFF
ON
37 RJ052F3HX**/RJ060F3HX**
RJ070F4HX**/RJ080F4HX**
AJ052FCJ3**/AJ068FCJ3**
AJ070FCJ4**/AJ080FCJ4**
(OFF)
8.0A
8.0A
9.0A
10.0A
10.0A
11.0A
(OFF)
7.0A
7.0A
7.5A
8.0A
8.5A
10.0A
OFF OFF
(OFF)
Display of the external unit
31
Setting an indoor unit address and installation option
A
Settings of PCB Display of the Outdoor unit
◆ Key Options of PCB Display
- K1 : pipe checking operation button
- K3 : Reset button
Key
- K2 : Function button
- K4 : View mode change button
K1
K2
1
Pipe Checking
Operation
(Display: )
Heat Mode Try run
(Display: )
2
-
Refrigerant Charging
)
(Display:
3
-
Cool Mode Try run
(Display: )
4
-
Pump down
)
(Display:
Push
K3
RJ040F2HX**/RJ050F2HX**
AJ040FCJ2**/AJ050FCJ2**
K4
37 Reset
K1
View mode
change
K2
※ Heat and Cool Mode Try run functions are just For Service Technician
K3
K4
RJ052F3HX**/RJ060F3HX**
RJ070F4HX**/RJ080F4HX**
AJ052FCJ3**/AJ068FCJ3**
AJ070FCJ4**/AJ080FCJ4**
K1
◆ K4 View mode Display changes
Push
Display Explanation
Push
Display Explanation
K2
0
Present Compressor Frequency
8
Discharge temperature
1
Target Compressor Frequency
9
OLP temperature
2
Order Compressor Frequency
10
Condenser temperature
3
EEV0 current step
11
Outdoor temperature
4
EEV1 current step
12
Running current
5
EEV2 current step
13
Target Discharge temperature
6
EEV3 current step3
14
Total capacity of the indoor units
7
Fan RPM (H: high, L: low, Blank: off)
15
Safety Control (just For Service Technician)
K3
K4
Display of the external unit
※ During the initial 60 seconds,
display 1 shows in sequence:
00→ 01→02 →...15→ 00...
※ The EEV 2 and EEV 3 of RJ040F2HX**/RJ050F2HX** /AJ040FCJ2**/AJ050FCJ2**are always displayed as blank.
※ The EEV 3 of RJ052F3HX**/RJ060F3HX** /AJ050FCJ3**/AJ068FCJ3**model is always displayed as blank.
32
Troubleshooting
A
The table below give indication about self diagnostic routine. Some of error code requires activities
exclusively for Authorise Service Center.
The error indicated on the PCB display of outdoor unit
EXPLANATION (The error indicated on the PCB display of outdoor unit)
REMARK
Communiaction error(indoor unable to receive data)
Check electrical connection and setting
Outdoor unit communication error(Abnormal data from indoor unit over 60 packet)
Check electrical connection and setting
Indoor unit room temperature sensor error (Open/Short)
Indoor unit heat exchanger in temperature sensor error (Open/Short)
Indoor unit heat exchanger out temperature sensor error (Open/Short)
Indoor unit sensor error-Evaporator pipe in sensor - Self diagnosis
Indoor unit sensor error-Evaporator pipe out sensor - Self diagnosis
Indoor Unit FAN Error
More than two indoor units cool and heat simultaneously
Indoor Unit EEPROM Error
Indoor Unit EEPROM Option Error
EVA-MID BREAK AWAY
EVA-IN BREAK AWAY
EVA-OUT BREAK AWAY
Failure of pipe check operation
Check piping connection and setting
No pipe check operation check
- occasion : try to operation after the installation through auto addressing mode without pipe check operation. Check setting
The number of Indoor unit mismatched
Check electrical connection and setting
Communication error between the outdoor and indoor unit
Check electrical connection and setting
Outdoor communication error between main micom and inverter micom
Outdoor communication error beween main micom and hub micom
Outside temperature sensor error(Short/Open)
- Error level: over 4.9V(-50°C) under 0.4V(93°C)
Condenser temperature sensor error(Short/Open)
- Error level: over 4.9V(-50°C) under 0.4V(93°C)
Outdoor unit sensor error - Condenser out sensor(Short/Open) - Self diagnosis
Compressor Discharge temperature sensor error
Compressor discharge sensor detached - Self diagnosis
Compressor OLP sensor error (Short/Open)
- Error condition : outdoor temperature under -20°C
- Error level : over 4.95V(-30°C) under 0.5V(151°C)
EvaIn1 Sensor Short/Open
EvaIn2 Sensor Short/Open
EvaIn3 Sensor Short/Open
EvaIn4 Sensor Short/Open
EvaIn5 Sensor Short/Open
EvaOut1 Sensor Short/Open
33
ENGLISH
DISPLAY
A
Troubleshooting
The table below give indication about self diagnostic routine. Some of error code requires activities
exclusively for Authorise Service Center.
The error indicated on the PCB display of outdoor unit
DISPLAY
EXPLANATION (The error indicated on the PCB display of outdoor unit)
REMARK
EvaOut2 Sensor Short/Open
EvaOut3 Sensor Short/Open
EvaOut4 Sensor Short/Open
EvaOut5 Sensor Short/Open
Outdoor unit freezing(Compressor stop)
Outdoor unit overload - Safety control(Compressor stop)
Outdoor unit high discharge temperature - Safety control (Compressor stop)
check pipe lenght, indoor unit filter,
refrigerant leakage/charge and
service port
check pipe lenght, refrigerant
leakage/charge
check pipe lenght, refrigerant
leakage/charge
Outdoor unit EEV open (Stopped indoor unit’s) -Self diagnosis
Outdoor unit EEV open (operating indoor unit’s) -Self diagnosis
High temperature(over 30°C) of outdoor as heating mode
Low temperature(under -10°C) of outdoor as cooling mode
Outdoor Fan Error
Communication cable mismatched between indoor and outdoor unit
Inverter compressor starting failure (5 times)
Compressor trip by input current control mode (PFC over current)
Compressor trip by OLP temperature control mode
Over current
Compressor Vlimit Error
DC link Voltage error (under 150V, over 410V)
Abnormal compressor running (Compressor Rotation Error)
Current sensor error
DC link Voltage sensor error
Outdoor unit EEPROM Error
Inverter micom zero-crossing error
Over voltage Error
34
Check electrical connection
A
Explaining
operations to the owner
ENGLISH
Before leaving the premises on which you have installed the air conditioner,
you should explain the following operations to the owner, making
reference to the appropriate pages in the owner’s instruction booklet.
1. How to start and stop the air conditioner.
2. How to select the operating mode and adjust the temperature and fan settings.
3. How to adjust the air flow direction.
4. How to set the timers.
5. How to remove and clean the filters.
䭭 Once the owner is happy with the basic operations, hand over the owner’s instruction ooklet and this installation
manual for storage in a handy and safe place.
Pump down procedure(when removing the product)
1.
Turn on the air conditioner and select Cool mode or pump down mode to run the compressor for 3 minutes.
2.
Release the valve caps on High and Low pressure side.
3.
Use L wrench to close the valve on the high pressure side.
4.
Approximately 2 minutes after, close the valve on the low pressure side.
5.
Stop operation of the air conditioner.
6.
Disconnect the pipes.
35
"EEE Yönetmeliğine Uygundur"
"This EEE is compliant with RoHS"
RJ040F2HX77
RJ050F2HX77
RJ052F3HX77
RJ060F3HX77
RJ070F4HX77
RJ080F4HX77
AJ777FCJ777
Air Conditioner
installation manual
This manual is made with 100% recycled paper.
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please
register your product at
www.samsung.com/register
EN ES FR IT PT DE EL
DB98-33017A-5