Samsung SCD-6021 User manual

HD-SDI CAMERA
User Manual
SCD-6021-ENGLISH-131230.indd 1
SCD-6021
2014-3-12 15:27:50
HD-SDI Camera
User Manual
Copyright
©2013 Samsung Techwin Co., Ltd. All rights reserved.
Trademark
is the registered logo of Samsung Techwin Co., Ltd.
The name of this product is the registered trademark of Samsung Techwin Co., Ltd.
Other trademarks mentioned in this manual are the registered trademark of their respective company.
Restriction
Samsung Techwin Co., Ltd shall reserve the copyright of this document. Under no circumstances, this document shall
be reproduced, distributed or changed, partially or wholly, without formal authorization of Samsung Techwin.
Disclaimer
Samsung Techwin makes the best to verify the integrity and correctness of the contents in this document, but no
formal guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own
responsibility. Samsung Techwin reserves the right to change the contents of this document without prior notice.
Warranty
If the product does not operate properly in normal conditions, please let us know. Samsung Techwin will resolve the
problem for free of charge. The warranty period is 3 years. However, the followings are excluded:
•• If the system behaves abnormally because you run a program irrelevant to the system operation.
•• Deteriorated performance or natural worn-out in process of time
™™ Design and specifications are subject to change without prior notice.
SCD-6021-ENGLISH-131230.indd 2
2014-3-12 15:27:51
overview
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
● overview
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11.Only use attachments/ accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13.Unplug this apparatus during lighting storms or when unused for
long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
SCD-6021-ENGLISH-131230.indd 3
English _3
2014-3-12 15:27:53
overview
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC
OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS
ON THE EQUIPMENT.
Apparatus shall not be exposed to dripping or splashing and that no objects
filled with liquids, such as vases, shall be placed on the apparatus.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature
accompanying the product.
4_ overview
SCD-6021-ENGLISH-131230.indd 4
2014-3-12 15:27:53
Class construction
An apparatus with CLASS construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
Batteries(battery pack or batteries installed) shall not be exposed to excessive
heat such as sunshine, fire or the like.
Disconnection Device
● overview
Battery
Disconnect the main plug from the apparatus, if it’s defected. And please call
a repair man in your location.
When used outside of the U.S., it may be used HAR code with fittings of
an approved agency is employed.
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than
that contained in the operating instructions unless you are qualified to do so.
Please use the input power with just one camera and other devices must not
be connected.
SCD-6021-ENGLISH-131230.indd 5
English _5
2014-3-12 15:27:53
overview
Please read the following recommend safety precautions carefully.
yy Do not place this apparatus on an uneven surface.
yy Do not install on a surface where it is exposed to direct sunlight, near
heating equipment or heavy cold area.
yy Do not place this apparatus near conductive material.
yy Do not attempt to service this apparatus yourself.
yy Do not place a glass of water on the product.
yy Do not install near any magnetic sources.
yy Do not block any ventilation openings.
yy Do not place heavy items on the product.
yy Do not expose the camera to radioactivity.
User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.
yy Reference : In case of providing information for helping of product’s usages
yy Notice : If there’s any possibility to occur any damages for the goods and
human caused by not following the instruction
 Please read this manual for the safety before using of goods and keep it in
the safe place.
6_ overview
SCD-6021-ENGLISH-131230.indd 6
2014-3-12 15:27:53
CONTENTS
overview
installation &
connection
Important Safety Instructions
Product Features
What’s Included
At a Glance
● overview
3
3
8
9
10
13Installation
16 Connecting with other Device
13
Operating Your Camera
SCD-6021-ENGLISH-131230.indd 7
20
appendix
36
20
21
Menu Configuration
Menu Setup
36Specification
38 Product Overview
39Troubleshooting
English _7
2014-3-12 15:27:53
overview
Product Features
•• Supports Full HD-SDI Video
By adopting a diagonal 6mm (1/3”) 2M pixel CMOS, the camera produces clear picture
quality.
•• Excellent low-illumination image quality
By adopting high-sensitive colour CMOS, the camera provides clear image quality under a
severe low illumination condition of 0.008 Lux .
•• SSNR3 (Samsung Super Noise Reduction) Function
The high-performance WN2 DSP chip effectively removes low-light gain noise and afterimage
to provide clear images even in dark environments.
•• Electrical Day&Night
This camera has a function that automatically selects the mode that is appropriate for
daytime or night-time conditions. The COLOR mode operates in daytime conditions to
provide optimum colors, and B/W mode operates in night-time conditions to enhance the
definition of the image.
•• INTELLIGENCE
Without assistance from an external sensor, this camera independently detects and traces
objects while examining stillness and movement to activate the alarm.
•• SSDR (Samsung Super Dynamic Range)
For images with high contrast between bright and dark areas from difficult lighting conditions
such as backlighting, this camera selectively illuminates darker areas while retaining the same
light level for brighter areas to even out the overall brightness.
•• Miscellaneous Functions
HLC(High Light Compensation), SENS-UP, FLIP (H/V-REV), D-ZOOM and PRIVACY
functions are provided.
•• OSD
By providing multi-lingual user-friendly OSD (On-screen Display) menu, the camera provides
easy handling of the camera.
8_ overview
SCD-6021-ENGLISH-131230.indd 8
2014-3-12 15:27:54
WHat’S IncLuDeD
Check if the main unit and all the following accessories are included in the product package.
Camera
1
3.MD_OU
4.RS_485+
5.RS_485-
3.MD_OU
4.RS_485+
5.RS_485-
Description
3.MD_OU
4.RS_485+
5.RS_485-
Quantity
● oVerVIeW
Item Name
3.MD_OU
4.RS_485+
5.RS_485-
Appearance
SAMSUNG
SAMSUNG
3.MD_OU
4.RS_485+
5.RS_485-
BLAC
485N:
GREE W: 485+UT
YELLO: MD_O N
BLUE : EXT_D
GND
GRAY K:
1
1.GN
2.EXT_DN
SCD-6021-ENGLISH-131230.indd 9
Quick Guide
Iron Screw
2
Used for fixing to an iron plate
Cable for the testingmonitor
1
Used to test the camera connection to a
portable display device
Function cable
1
Template
1
b
UPDATE
Product installation guide
1.G
N
XT_D D
N
2.E
3.MD_OU T
4.RS_485+
5.RS_485-
3.M
D_
4.RS
OU
5.RS _485 T
+
_4
85
-
English _9
D
GN DN
1.
T_
EX
3.M
D
4.RS _O
U
5.RS _485 T
+
_4
85
-
2.
2014-3-12 15:28:05
D
GN DN
1.
T_
EX
2.
overview
at a GLance
5.RS
_OU
+
3.MD
_485
4.RS
_485
appearance
Item
Description
a
Top cover
Case cover used to protect the lens and the main unit.
b
Camera Case
Covers the lens and camera body.
10_ overview
SCD-6021-ENGLISH-131230.indd 10
2014-3-12 15:28:08
Inside
_OU
+
3.MD
_485
4.RS
_485
5.RS
● oVerVIeW
1.GN
2.EXT_DN
SCD-6021-ENGLISH-131230.indd 11
English _11
2014-3-12 15:28:10
overview
Item
Description
a
Internal Cover
It is a cover to protect the main body.
b
Lens
Lens for the camera.
The switch is used for setting and adjusting the camera’s functions and
properties.
_/+
c
SETUP Switch
$/%
d
I/O Port
Move this switch left or right to move the cursor or change
the value in the menu.
Move this switch up or down to move the cursor in the
menu.
▪
Press the switch to set the function in menu. To move to a
sub-menu item in the menu, press this switch.
GREEN(485–)
Signal port for RS-485– communication.
YELLOW(485+)
Signal port for RS-485+ communication.
BLUE(MD_OUT)
Output port that signals when a motion is detected.
GRAY(EXT_D/N)
External signal input port for Day/Night mode setup.
BLACK(GND)
Earth-grounding port for external signal.
Analogue video output terminal of Video.
e
VIDEO
Use a monitor cable for testing the camera with a portable display.
(for installation)
f
Power Port
Used to plug the power cable.
g
HD-SDI Video
Out terminal
BNC terminal for HD-SDI video signal output.
12_ overview
SCD-6021-ENGLISH-131230.indd 12
2014-3-12 15:28:10
installation & connection
InStaLLatIon
precautions before installation
Ensure you read out the following instructions before installing the camera:
Disassembling
OU
3.MD_ 85+
4.RS_4 855.RS_4
1. Use one hand to hold the camera’s bottom part and turn the cover counterclockwise
with another hand to separate it.
● InStaLLatIon & connectIon
• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight
of the camera including the installation bracket.
• Stuck-in or peeled-off cables can cause damage to the product or a fire.
• For safety purposes, keep anyone else away from the installation site. And put asid
personal belongings from the site, just in case.
SCD-6021-ENGLISH-131230.indd 13
OU
3.MD_485+
4.RS_ 4855.RS_
OU
3.MD_485+
4.RS_ 4855.RS_
2. Lift up the inner cover to separate it.
English _13
2014-3-12 15:28:12
installation & connection
Installation
1. Attach the installation template to the selected
area and punch 2 holes as shown in the
figure.
2. Use the 2 supplied screws to fix the camera
to the 2 punched holes.
` Set the <FRONT TOP> mark imprinted on the camera
to face the direction of camera monitoring.
Locking direction
(Clockwise)
Unlocking direction
(Anti-clockwise)
3. Connect the camera internal terminal with the
corresponding cable.
4. Adjust the lens in a desired direction by
referring to the “Adjusting the monitoring
direction for the camera” section. (page 15)
5. Fasten the dome case (dome cover +camera case)
to the main body as shown in the figure.
J
` Pay attention to the direction for assembly.
14_ installation & connection
SCD-6021-ENGLISH-131230.indd 14
2014-3-12 15:28:14
Adjusting the monitoring direction for the camera
Panning
● installation & connection
Tilting
Rotation
❖❖ Adjusting the monitoring direction
You can adjust the camera direction only when the camera is fixed on the ceiling.
Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called
Tilt, and turning the lens on its axis is called Rotation.
-- The effective range of pan is a total of 354 degrees.
-- The effective range of rotation is a total of 355 degrees.
-- The effective range of tilt is a total of 67 degrees.
JJ `` In some angles, the top cover may cause cutting some part of the monitoring object.
`` Do not rotate the focus/zoom lens by force after removing the cover front.
Otherwise, it may cause an incorrect focus due to a motor failure.
❖❖ Methods of adjustment
1. After installing the camera, adjust the panning angle in consideration of the
monitoring direction.
2. Set the horizontal angle so that the image is not reversed.
3. Adjust the tilt angle so that the camera faces toward the monitoring object.
SCD-6021-ENGLISH-131230.indd 15
English _15
2014-3-12 15:28:16
installation & connection
connectInG WItH otHer DeVIce
DVR
System Controller
or
Test monitor for installation
R+
T+ T- R-
CONVERTER
RS232C
RS485, 422
U
3.MD_O85+
4.RS_4 855.RS_4
N: 485 +
EE
485
GR
W:
UT
_O N
LLO
YE E: MD
T_D
BLU
: EX GND
AY
:
GR
CK
BLA
RS-485
Converter
PC
Motion detection output device
Day/Night mode controller
connecting to the monitor
Connect the video out port of the camera to the video input port of the monitor.
M
` To check the display screen after installing the camera for the first time, you can use the C-Video
port to check the video screen.
` You can set the video output type to either NTSC or PAL. (page31)
` The C-Video source (4:3) will be displayed with either side truncated in comparison with the
HD-SDI video.
` The video source from the HD-SDI port can be displayed on the dedicated monitor. To display the
source on a commercial monitor, you need a converter to convert the video signal as appropriate.
16_ installation & connection
SCD-6021-ENGLISH-131230.indd 16
2014-3-12 15:28:18
Video Cable
Maximum video transfer
distance
Recommended cable
specification
100~140m
5C2V(75ohm)
200m
L-6CHD(75ohm)
(SDI-specific Cable)
RS-485 Communications
Using RS-485 communication, the camera menu can be accessed using Samsung
Techwin’s System Controller or the DVR.
•• For accessing the camera from a computer
Use a RS-485 converter to connect the camera’s control port with the computer’s
serial cable.
Ex) Serial port (COM1) of computer  Serial Cable  RS-485 Converter  Camera’s
RS-485 control port
•• For accessing the camera from a DVR or the System Controller
Connect the camera’s RS-485+ and RS-485– terminals to the RS-485 control
board’s terminals of desired device with a RS-485 cable (TRX+ and TRX–).
Control ports of RS-485 Controller
RS-485 ports of the camera
(+) CONNECTION TERMINAL (TRX+)
485+
(–) CONNECTION TERMINAL (TRX–)
485–
● installation & connection
The cable connecting the camera’s video output and a monitor is a BNC coaxial cable as
shown below.
If the distance between the camera and the monitor exceeds the recommended maximum,
please use an auxiliary video amp.
Default RS-485 communication settings
Item
Camera Number
Transfer Rate
Communication Mode
Return Data
Default
1
9600
8-NONE-1
Not used
constructing a proprietary controller for direct camera control, apply Pelco-D or SamsungJJ `` When
Techwin protocol.
SCD-6021-ENGLISH-131230.indd 17
`` Use only a DVR model that supports HD-SDI saving.
English _17
2014-3-12 15:28:18
installation & connection
External Day/Night Switching Input
Day/Night mode of the camera can be switched by signal from an external device.
MM `` To(Pageuse28)this function, <DAY/NIGHT> setting of the camera should be set to the <EXTERN>.
Motion Detection Signal Out
Upon a motion detection, the port outputs signal for an external device for display or operation.
When a motion is detected, the port outputs 3.3V signal.
MM `` To use this function, <ALARM OUT> setting of the camera should be set to <ON>. (Page 33)
HD-SDI Monitor
1.GN
2.EXT_DN
POWER
18_ installation & connection
SCD-6021-ENGLISH-131230.indd 18
2014-3-12 15:28:20
Power Supply
Use the screwdriver to connect each line (+, –) of the power cable to the corresponding
power port of the camera.
● Operating Your Camera
JJ `` Be careful not to reverse the polarity when you connect the power cable.
`` Be sure to turn the power off the device to be connected.
For DC Power Supply
You can use either one of DC 12V/2A~4A adaptor.
Resistance of copper wire [at 20°C (68°F)]
Wire specification (AWG)
#24(0.22mm2)
#22(0.33mm2)
#20(0.52mm2)
#18(0.83mm2)
Resistance (Ω/m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.028
0.018
0.011
0.006
Recommended Distance (m)
Less than 20
Less than 30
Less than 30
Less than 30
•• As shown in the table above, you may encounter a voltage-sag depending on the
wire length. If you use an excessively long wire for camera connection, the camera
may not work properly.
`` Voltage for proper camera operation: DC 12V±10%
`` Voltage drop shown in the table above may show difference from the actual depending on the
SCD-6021-ENGLISH-131230.indd 19
manufacturer and cable type.
English _19
2014-3-12 15:28:20
operating your camera
Menu Configuration
MAIN SETUP
•BRIGHTNESS
•SHUTTER
•AGC
•SENS-UP
•DEFOG
•RETURN
•ATW
•OUTDOOR
•INDOOR
•MANUAL
•AWC ➝ SET
SSDR
•OFF
•ON
BACKLIGHT
•OFF
•WDR
•BLC
SSNR3
•ON
•OFF
•AUTO
•EXTERN
•COLOR
•BASIC
•DAY/NIGHT
•BACKLIGHT
•ITS
•INDOOR
•USER
•CAM TITLE
•IMAGE ADJ
•INTELLIGENCE
•PRIVACY
•COMM ADJ
•LANGUAGE
•RESET
•RETURN
EXPOSURE
WHITE BAL
DAY/NIGHT
PROFILE
•HLC
•B/W
•BANK
SPECIAL
EXIT
•EXIT
20_ Operating Your Camera
SCD-6021-ENGLISH-131230.indd 20
2014-3-12 15:28:20
Menu Setup
To configure the camera’s function settings, use the button on the inside of the product.
● Operating Your Camera
1.GN
2.EXT_DN
•• $% : Moves up/down in menu.
•• _+ : Moves right/left in menu.
•• ▪ : Press the switch to set the function in camera menu.
To move to a sub-menu item in the menu, press this switch.
1. Press the SET button.
•• Enters the function menu.
The selected function’s menu appears on the monitor.
MAIN SETUP
Use up/down buttons
to set the desired item.
► 1. EXPOSURE 2. WHITE BAL
ATW
3. SSDRON
4. BACKLIGHTOFF
5. SSNR3ON
6. DAY/NIGHTAUTO
7. PROFILEBASIC
8. SPECIAL
9. EXIT
Use right/left buttons
to change the
selection.
2. Use the Up/Down buttons to select a desired function.
•• Move the button up or down to move the arrow up or down.
Set the arrow to indicate the desired item.
SCD-6021-ENGLISH-131230.indd 21
English _21
2014-3-12 15:28:21
operating your camera
3. Use the Right/Left buttons to select a desired function.
•• Move the button right or left to display available values or settings.
Set the desired setting value using the button.
4. To finish, select <EXIT> and press the SET button.
with the icon also has sub menus. To select a sub menu, select an item with the icon
MM `` Ananditem
press the Function Setup switch.
`` An item with the --- icon is unavailable due to function settings.
EXPOSURE
1. When the SETUP menu screen is displayed,
select <EXPOSURE> by using the Function
Setup switch so that the arrow indicates
<EXPOSURE> .
2. Select a desired mode using the Function
Setup switch.
•• BRIGHTNESS : Adjust the screen brightness.
•• SHUTTER : You can select the shutter.
-- ESC : Select this to control the shutter speed
automatically. If ESC is selected, the shutter
speed is automatically controlled depending on
the ambient illumination of the subject.
-- MANUAL : You can control shutter speed
manually((1/30~1/16,000 、x2~x60))
MAIN SETUP
► 1. EXPOSURE
2. WHITE BAL
ATW
3. SSDRON
4. BACKLIGHTOFF
5. SSNR3ON
6. DAY/NIGHTAUTO
7. PROFILEBASIC
8. SPECIAL
9. EXIT
EXPOSURE SETUP
► 1. BRIGHTNESS .... .... * .... ....50
2. SHUTTER
ESC
3. AGCHIGH
4. SENS-UP
AUTO
5. DEFOG--6. RETURN
-- A.FLK : Select this when you experience
picture flicker, this happen when there is a
clash with the installed lighting frequency.
JJ `` When the SHUTTER is set to MANUAL or A.FLK mode, SENS-UP will be disabled.
`` Carefully position the camera when installing, since produced image quality might be poor if
framing a bright light source while the shutter mode of EXPOSURE is set to AUTO.
22_ Operating Your Camera
SCD-6021-ENGLISH-131230.indd 22
2014-3-12 15:28:22
•• AGC(AUTO GAIN CONTROL) : The higher the gain level, the brighter the screen but the greater the noise.
-- OFF : Not being used
-- Low : Allows automatic gain control from 5.3dB to 20dB.
● Operating Your Camera
-- Medium : Allows automatic gain control from 5.3dB to 26dB.
-- High : Allows automatic gain control from 5.3dB to 32dB.
•• SENS-UP : When it is night or dark, the camera automatically detects the light level
and maintains a clear picture if this mode is activated.
-- OFF : Deactivates the SENS-UP function.
-- AUTO : Activates the SENS-UP function.
•• DEFOG : Through the defogging function,
camera can automatically recognize fog
concentration of the image, defog, self correct
in hazy, rainy, flue gas and other inclement
weather to get a clear image.
-- AUTO : The camera will automatically correct
image according to the defogging level (low,
middle, high) set by the user.
DEFOG SETUP
► LEVEL
RETURN
MIDDLE
-- MANUAL : The camera will adjust the definition
of the image according to user’s preferences
through the defogging level (low, middle, high).
-- OFF : Turn off defogging function.
•• RETURN : Select this to save the changes in the EXPOSURE menu and return to
the SETUP menu.
the SET button while in AUTO mode to adjust the automatic scene accumulation multiplier
JJ `` Press
for low-illumination operation. (x2 ~ x60)
SCD-6021-ENGLISH-131230.indd 23
`` The greater the video accumulation factor is, the brighter the screen is, but the afterimage of a
moving object grows accordingly.
`` Although noise, spots, and whitish symptoms may occur in higher accumulation, this is normal.
`` If the gain control (AGC) of EXPOSURE mode is set to OFF, SENS-UP mode is accordingly set to
‘- - -‘.
English _23
2014-3-12 15:28:22
operating your camera
White Bal (White Balance)
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed,
select <WHITE BAL> by using the Function
Setup switch so that the arrow indicates
<WHITE BAL>.
2. Select a desired mode using the Function
Setup switch.
Select one of the following 5 modes, as appropriate
for your purpose.
MAIN SETUP
1. EXPOSURE
► 2. WHITE BAL
ATW
3. SSDRON
4. BACKLIGHTOFF
5. SSNR3ON
6. DAY/NIGHTAUTO
7. PROFILEBASIC
8. SPECIAL
9. EXIT
•• ATW : Select this when the color temperature is between 2,400˚K and 11,000˚K.
•• OUTDOOR : Select this when the color temperature is between 1,700˚K and
11,000˚K. (sodium light inclusion)
•• INDOOR : Select this when the color
WHITE BAL MANUAL STEUP
temperature is between 4,500˚K and 8,500˚K.
.... .... * .... ....
► RED
552
.... .... * .... ....
BLUE
552
•• MANUAL : Select this to fine-tune White
RETURN
Balance manually. Set White Balance first by
using the ATW or AWC mode. After that switch
to MANUAL mode, fine-tune the White Balance
and the Function Setup switch.
•• AWC ➞ SET : To find the optimal luminance
level for the current environment, point the
camera towards a sheet of white paper and press the Function Setup switch. If the
environment changes, readjust it.
Balance may not work properly under the following conditions. In this case select the AWC
JJ `` White
mode.
-- When the ambient illumination of the subject is dim.
-- If the camera is directed towards a fluorescent light or is installed in a place where illumination
changes dramatically, the White Balance operation may become unstable.
24_ Operating Your Camera
SCD-6021-ENGLISH-131230.indd 24
2014-3-12 15:28:22
SSDr (SamSunG Super DynamIc ranGe)
1. When the SETUP menu screen is displayed,
select <SSDr> by using the Function Setup
switch so that the arrow indicates <SSDr>.
2. Use the Function Setup switch to change the
SSDR level in the sub menu according to the
contrast between bright and dark areas.
MAIN SETUP
1.
2.
► 3.
4.
5.
6.
7.
8.
9.
EXPOSURE
WHITE BAL
SSDR
BACKLIGHT
SSNR3
DAY/NIGHT
PROFILE
SPECIAL
EXIT
ATW
ON
OFF
ON
AUTO
BASIC
● opeRATIng YouR CAmeRA
SSDR illuminates darker areas of an image while
retaining the same light level for brighter areas to
even out the overall brightness of images with high
contrast between bright and dark areas.
SSDR SETUP
► LEVEL
RETURN
.... .... .... * ....
8
• SSDr : Adjust the dynamic range level.
SCD-6021-ENGLISH-131230.indd 25
SSDR ON
SSDR OFF
English _25
2014-3-12 15:28:23
operating your camera
BACKLIGHT
This camera is designed so that it delivers a distinctive subject and background at the
same time, even when the subject is in backlight, by adopting a function of the proprietary
WN2 DSP chip.
1. When the SETUP menu screen is displayed,
select <BACKLIGHT> by using the Function
Setup switch so that the arrow indicates
<BACKLIGHT>.
2. Select a desired mode using the Function Setup
switch depending on the camera purpose.
•• BLC : Enables a user to select a desired area
on a picture and view that area more clearly.
-- LEVEL : Adjust level of the BLC function.
-- TOP/BOTTOM/LEFT/RIGHT : Adjust the area
to be enhanced.
•• HLC (High Light Compensation) : If the scene
contains extremely bright light areas such as:
from car headlight, the light can mask out much
of the on-screen detail.
-- LEVEL : Adjust level of the HLC function.
MAIN SETUP
1. EXPOSURE
2. WHITE BAL
ATW
3. SSDRON
► 4. BACKLIGHTOFF
5. SSNR3ON
6. DAY/NIGHTAUTO
7. PROFILEBASIC
8. SPECIAL
9. EXIT
BLC SETUP
► 1. LEVELMIDDLE
.... * .... .... ....30
2. TOP
.... .... .... * ....75
3. BOTTOM
.... * .... .... ....30
4. LEFT
.... .... .... * ....75
5. RIGHT
6. RETURN
-- MASK COLOR : Change the color of the
masking area.
-- MASK TONE : Change the brightness of the
masking area.
-- TOP/BOTTOM/LEFT/RIGHT : Adjust the area
to be enhanced.
•• WDR (wide Dynamic range) : It displays a
sharp image of the objects in a scene where
both bright and dark areas exist.
-- LEVEL : Select a sensitivity level of WDR.
HLC SETUP
► 1. LEVELMIDDLE
2. MASK COLOR
BLACK
3. MASK TONE .... .... * .... ....5
.... * .... .... ....30
4. TOP
.... .... .... * ....75
5. BOTTOM
.... * .... .... ....30
6. LEFT
.... .... .... * ....70
7. RIGHT
8. RETURN
•• OFF : Not being used
3. Select a desired mode using the Function
Setup switch.
WDR SETUP MODE
► LEVEL
RETURN
MIDDLE
26_ Operating Your Camera
SCD-6021-ENGLISH-131230.indd 26
2014-3-12 15:28:23
JJ `` Because there can be a difference in the effectiveness of HLC according to the amount of light
area in the screen, optimize the installation angle for the best HLC performance.
● Operating Your Camera
`` When dark, the HLC is only activated when a bright light exceeding a specific size.
`` The HLC is not activated in day light or when bright light is not present at night.
SSNR3
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed,
select <SSNR3> by using the Function Setup
switch so that the arrow indicates <SSNR3>.
2. Select a desired mode using the Function
Setup switch.
•• ON : Activates SSNR3 so that noise is reduced.
•• OFF : Deactivates SSNR3. Noise is not
reduced.
MAIN SETUP
1. EXPOSURE
2. WHITE BAL
ATW
3. SSDRON
4. BACKLIGHTOFF
► 5. SSNR3ON
6. DAY/NIGHTAUTO
7. PROFILEBASIC
8. SPECIAL
9. EXIT
3. Set the SSNR3 mode to <ON> and press the
Function Setup switch. Then you can adjust the noise reduction level.
JJ `` You cannot set the SSNR3 to ‘ON’ or ‘OFF’ when the AGC mode of the ‘EXPOSURE’ menu is ‘OFF’.
`` When adjusting the noise reduction level in the SSNR3 mode, remember that the higher the level
set, the more the noise level will be reduced, as will the brightness of the image.
DAY/NIGHT
You can display pictures in color or in black and white.
1. When the SETUP menu screen is displayed,
select <DAY/NIGHT> by using the Function
Setup switch so that the arrow indicates <DAY/
NIGHT>.
2. Select a desired mode using the Function
Setup switch according to the picture display
you want.
•• COLOR : The picture is always displayed in
color.
SCD-6021-ENGLISH-131230.indd 27
MAIN SETUP
1. EXPOSURE
2. WHITE BAL
ATW
3. SSDRON
4. BACKLIGHTOFF
5. SSNR3ON
► 6. DAY/NIGHTAUTO
7. PROFILEBASIC
8. SPECIAL
9. EXIT
English _27
2014-3-12 15:28:24
operating your camera
•• B/W : The picture is always displayed in black
and white.
•• AUTO : The mode is switched to <COLOR> in
a normal environment, but switches to <B/W>
mode when ambient illumination is low. To set
up the switching time for AUTO mode, press
the Function Setup switch.
-- DWELL TIME : You can select day/night
switching delay time from.
➝ 5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s
DAY/NIGHT AUTO SETUP
► 1. COLOR  B/W
DWELL TIME
5 SEC
DURATIONSLOW
2. B/W  COLOR
DWELL TIME
10 SEC
DURATIONSLOW
3. RETURN
-- DURATION : Adjust the brightness of the lighting where the mode switch occurs.
•• EXTERN : Control the image modes of Color and B/W when an external controller is
synchronized via the Alarm In port.
AGC in the EXPOSURE menu is ‘OFF’, ‘---’ mode operates as selecting ‘AUTO’ mode cannot
JJ `` When
be selected.
PROFILE
1. When the SETUP menu screen is displayed,
select <PROFILE> by using the Function
Setup switch so that the arrow indicates
<PROFILEL>.
MAIN SETUP
1. EXPOSURE
2. WHITE BAL
ATW
3. SSDRON
4. BACKLIGHTOFF
5. SSNR3ON
6. DAY/NIGHTAUTO
► 7. PROFILEBASIC
8. SPECIAL
9. EXIT
2. Select a desired mode using the Function
Setup switch.
•• BASIC : The most common environment is set
to meet.
•• DAY/NIGHT : It will be set automatically so it
optimizes to the day or night conditions,respectively.
•• BACKLIGHT : It will be set automatically so you can distinguish the object from the
background in a severe backlighting scene.
•• ITS : It will be set automatically so you can easily check the traffic conditions.
•• INDOOR : It will be set automatically to help you take a picture in a regular indoor
lighting condition.
•• USER : Automatically configures the camera to your custom settings.
1) Select Custom for Simple Setup mode.
2) Configure the menu options to your custom settings.
3) The settings are automatically saved as Custom mode.
4) Profile user mode don’t initialize when menu resets.
28_ Operating Your Camera
SCD-6021-ENGLISH-131230.indd 28
2014-3-12 15:28:24
•• BANK : The system will automatically set if dark and bright area are all exist at same
time, sothat you can recognize the object in bank easily.
*In the PROFILE menu, you can configure the following camera settings at once.
ITS
INDOOR
USER BANK
SHUTTER
ESC
ESC
ESC
ESC
ESC
ESC
---
AGC
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
HIGH
WHITE BAL
ATW
ATW
ATW
BACKLIGHT
OFF
OFF
BLC
OUTDOOR INDOOR
OFF
OFF
ATW
ATW
OFF
WDR
SSNR3
ON
ON
ON
ON
ON
ON
ON
DAY/NIGHT
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
AUTO
● Operating Your Camera
BASIC DAY/NIGHT BACKLIGHT
SPECIAL
1. When the SETUP menu screen is displayed,
select <SPECIAL> by using the Function Setup
switch so that the arrow indicates <SPECIAL>.
2. Select a desired mode using the Function
Setup switch.
SCD-6021-ENGLISH-131230.indd 29
MAIN SETUP
1. EXPOSURE
2. WHITE BAL
ATW
3. SSDRON
4. BACKLIGHTOFF
5. SSNR3ON
6. DAY/NIGHTAUTO
7. PROFILEBASIC
► 8. SPECIAL
9. EXIT
SPECIAL SETUP
► 1. CAM TITLE
OFF
2. IMAGE ADJ
3. INTELLIGENCE
OFF
4. PRIVACY 5. COMM ADJ 6. LANGUAGEENGLISH
7. RESET
8. RETURN
English _29
2014-3-12 15:28:24
operating your camera
•• CAM TITLE : If you enter a title, the title will
appear on the monitor.
1) If the SPECIAL menu screen is displayed, use
the Function Setup switch so that the arrow
indicates <CAM TITLE>.
2) Set it to <ON> by using the Function Setup
switch.
3) Press the Function Setup switch.
CAM TITLE SETUP
A B C
NOP
a b c
n o p
– . 0
← →
D
Q
d
q
1
C
EF
R S
e f
r s
2 3
L R
G H I J K L M
TU V W X Y Z
g h i j k l m
t u v w x y z
4 5 6 7 8 9
P O S
E N D
— — — — — — — — — — — — — —
4) Use the Function Setup switch to move to a
desired letter and select the letter by pressing the Function Setup switch. Repeat this
to enter multiple letters. You can enter up to 15 letters.
5) Enter a title, move the cursor to <POS>
and press the Function Setup switch. The
entered title appears on the screen. Select
the position to display the title on the screen
by using the Function Setup switch and press
the Function Setup switch. When the position
is determined, select <END> and press
the Function Setup switch to return to the
SPECIAL menu.
ABCD
←→↑↓ to Locate, then SET
the CAM TITLE menu is ‘OFF’, no title will be displayed on the monitor screen even if you
JJ `` When
enter one.
`` Only English is available in this mode.
`` If you move the cursor to CLR and press the Function Setup switch, all the letters are deleted.
To edit a letter, change the cursor to the bottom left arrow and press the Function Setup switch.
Move the cursor over the letter to be edited, move the cursor to the letter to be inserted and then
press the Function Setup switch.
30_ Operating Your Camera
SCD-6021-ENGLISH-131230.indd 30
2014-3-12 15:28:24
•• IMAGE ADJ :
1) When the SPECIAL menu screen is displayed,
select <IMAGE ADJ> by using the Function
Setup switch so that the arrow indicates
<IMAGE ADJ>.
SPECIAL SETUP
● Operating Your Camera
1. CAM TITLE
OFF
► 2. IMAGE ADJ
3. INTELLIGENCE
OFF
4. PRIVACY 5. COMM ADJ 6. LANGUAGEENGLISH
7. RESET
8. RETURN
2) Select a desired mode using the Function Setup switch.
-- MONITOR : Please change the settings value
of video appropriate to your monitor.
•• LCD : Please select this menu item when
using a LCD monitor.
•• USER : Please use this menu item when
using a monitor other than standard ones.
You can change the gamma, color level and
reset in the sub menus.
IMAGE SETUP
► 1. MONTIORLCD
2. H-REVOFF
3. V-REVOFF
4. D-ZOOMOFF
5. DISOFF
6. SHARPNESSON
7. OSD COLOR
WHITE
8. VIDEO OUT FORMAT 9. RETURN
-- H-REV : You can flip the picture horizontally on
the screen.
-- V-REV : You can flip the picture vertically on the screen.
-- D-ZOOM : You can use a digital zoom of x2 ~ x16.
-- DIS : Compensates the image automatically when it is seen to shake for stable image
output.
-- SHARPNESS : As you increase this value, the picture outline becomes stronger and
clearer. Adjust this value appropriately depending on the sharpness of the picture.
-- FONT COLOR : You can change the OSD font color. (White, Yellow, Green, Red, Blue)
-- VIDEO OUT FORMAT : Sets the video size and video fmt.
•• VIDEO SIZE : Sets the image resolution of the HD-SDI output of the camera.
Select the desired setting and press the SET button. (NTSC : 1080i 60, 1080p 30,
720p 60 ; PAL : 1080i 50, 1080p 25, 720p 50)
•• VIDEO FMT :Sets the video output format of the Video port on the camera provided
for test and installation.(NTSC, PAL)
-- RETURN : Select this to save the settings for the IMAGE ADJ menu and to return to
the SPECIAL menu.
you increase the sharpness level excessively, the image may be displayed abnormally or it can
JJ `` Ifcause
a noise.
SCD-6021-ENGLISH-131230.indd 31
English _31
2014-3-12 15:28:24
operating your camera
•• INTELLIGENCE : Commands the camera to
motion-detect and trace an object.
-- DETECTION : Since the camera detects
motion without any additional external
sensor,you can monitor activity more effcient.
-- TRACKING : Commands the camera to detect
and trace a moving object.
►TYPE : Two types, line and area, of fences
INTELLIGENCE
► 1. DETECTION OFF
2. TRACKINGOFF
3. FIXED/MOVED OFF
4. TAMPERING OFF
5. DETECT BOX
OFF
6. ALARM OUT
OFF
7. SETUP CONFIG
OFF
8. RETURN
are available.
►COUNT : Displays the number of times
that an object enters or leaves a fenced area.
►DISPLAY : Determines whether to use the
fence selected in the FENCE.
►FILL : Fill or remove color from the FENCE.
TRACKING
► 1. TYPELINE
2. COUNTOFF
3. DISPLAYON
4. FILLOFF
5. POSITION 6. RETURN
►POSITION : Defines the position and
detection direction of a line or fenced area
1) LINE FENCE
-- SEL POS : Selects a position from POS1,POS2.
-- X POS / Y POS : Adjust the size and position of the selected line fence.
-- DIRECTION
• DIR1 : Detects objects moving right to left on the fence line.
• DIR2 : Detects objects moving left to right on the fence line.
•• DIR1/2 : Detects all objects moving crosswise on the fence line.
-- RETURN : Select this to save the POSITION menu settings and return to the
TRACKING menu.
2) AREA FENCE
-- SEL POS : Selects a position from POS1 ~ POS4.
-- X POS / Y POS : Adjust the size and position of the selected area fence.
-- DIRECTION
• IN : Detects objects entering the fenced area.
•• OUT : Detects objects exiting the fenced area.
•• IN/OUT : Detects all objects entering and exiting the fenced area.
-- RETURN : Select this to save the POSITION menu settings and return to the
TRACKING menu.
►RETURN :Select this to save the TRACKING menu settings and return to the
INTELLIGENCE menu.
32_ Operating Your Camera
SCD-6021-ENGLISH-131230.indd 32
2014-3-12 15:28:25
► SEL POS
X POS
Y POS
... ... ... *... ...
* ... ... ... ... ...
POS1
106
12
DIR1
TRACKING
► SEL POS
X POS
Y POS
POS1
... ... ... *... ...
* ... ... ... ... ...
DIRECTION
RETURN
70
30
IN
● Operating Your Camera
DIRECTION
RETURN
TRACKING
-- FIXED/MOVED : De tects an object that emerges or disappears from the screen, or
stays onscreen without movement.
JJ `` A detection (FIXED/MOVED) error may occur if :
•• multiple motions occur continuously in random directions
•• a fixed object moves in one position continuously
•• a second object screens the first moving o bjec t
-- TAMPERING : You can set to detect tampering attempts and trigger events, such as
blocked lens.
-- DETECT BOX : Outlines an object on the screen in a box when its movement
matches a custom Motion Type.
-- ALARM OUT : Releases a signal from the MD Output Terminal of the camera when an
object’s movement matches a custom Motion Type.
-- SETUP CONFIG :
►DETECT AREA : Defines the Motion Detection
area.
•• AREA SEL: You can select up to 4 areas.
SETUP CONFIG
► 1. DETECT AREA 2. SENSI TIVITY
3
3. DET.SIZE 3
4. RETURN
•• MODE : Determines whether to use the area
selected in the AREA.
•• DETECT ALARM: Determines whether to
use the detect alarm selected in the AREA.
•• TOP / BOTTOM / LEFT / RIGHT : Adjust the
size and position of the selected area.
•• RETURN : Select this to save the DETECT
AREA menu settings and return to the
SETUP CONFIG menu.
►SENSITIVITY : Set the sensitivity of the motion
SCD-6021-ENGLISH-131230.indd 33
DETECT AREA
► AREA SEL
MODE
DETECT ALARM
TOP
BOTTOM
LEFT
RIGHT
RETURN
* ... ... ... ... ...
... ... ... ... ...*
* ... ... ... ... ...
... ... ... ... ...*
AREA1
OFF
OFF
32
1048
64
1888
English _33
2014-3-12 15:28:25
operating your camera
►DET. SIZE : Selects an object size to detect on the screen. When adjusting the
detection size, note that the higher the level means the bigger detection size.
►RETURN : Select this to save the SETUP CONFIG menu settings and return to the
INTELLIGENCE menu.
-- RETURN : Select this to save the INTELLIGENCE menu settings and return to the
SPECIAL menu.
•• PRIVACY : Mask an area you want to hide on
the screen.
1) When the SPECIAL menu screen is displayed,
press the Function Setup switch so that the
arrow indicates <PRIVACY>.
PRIVACY
► 1. TYPE 1
2. TYPE 2
3. RETURN
OFF
OFF
2) Set up the mode using the Function Setup
switch.
-- TYPE 1 (In this type , the shape of selected
area is rectangular)
►AREA SEL: You can select up to 16 PRIVACY
areas.
►AREA MODE : Determines whether to use the
area selected in the AREA SEL.
►MASK COLOR : Determine area color. You can
TYPE 1
► 1. AREA SEL
AREA1
2. AREA MODE
OFF
3. MASK COLOR
GRAY
...
...
...
...
...
23
4. TOP
*
... ... ...* ... ... 59
5. BOTTOM
6. LEFT
* ... ... ... ... ... 35
... ... ...* ... ... 67
7. RIGHT
8. RETURN
select Green, Red, Blue, Black, White, Gray.
►TOP / BOTTOM / LEFT / RIGHT : Adjust the
size and position of the selected area.
►RETURN : Select this to save the TYPE 1 menu
settings and return to the PRIVACY menu.
-- TYPE 2 ( In this type , the shape of selected
area is polygonal)
►AREA SEL: You can select up to 4 PRIVACY
TYPE 2
► 1. AREA SEL
AREA1
2. AREA MODE
OFF
3. MASK COLOR
GRAY
4. SEL POS
L_TOP
... ... ...* ... ... 30
5. X POS
6. Y POS
* ... ... ... ... ... 10
7. RETURN
areas.
►AREA MODE : Determines whether to use the area selected in the AREA SEL.
►MASK COLOR : Determine area color. You can select Green, Red, Blue, Black,
White, Gray.
►SEL POS/XPOS/YPOS : Adjust the size and position of the selected area.
34_ Operating Your Camera
SCD-6021-ENGLISH-131230.indd 34
2014-3-12 15:28:25
►RETURN : Select this to save the TYPE 2 menu settings and return to the
PRIVACYmenu.
-- RETURN : Select this to save the PRIVACY menu settings and return to the SPECIAL
menu.
● Operating Your Camera
•• COMM ADJ (Communication Adjustment) :
This function sets up the camera
communication status when controlling the
camera through an external control device.
1) When the SPECIAL menu screen is displayed,
press the Function Setup switch so that the
arrow indicates <COMM ADJ>.
COMMUNICATION SETUP
► 1. PROTOCOLSAMSUNG-T
2. CAM ID
* .... .... .... ....1
3. BAUD RATE
9600
4. UART MODE
8-N-1
5. DISP ID
OFF
6. RET PKT
ENABLE
7. RETURN
2) Set up the mode using the Function Setup
switch.
-- PROTOCOL : Select the communication PROTOCOL. (SAMSUNG-T, SAMSUNG-E,
Pelco-D, Pelco-P, Bosch, Honeywell, Vicon, Panasonic, GE, AD)
-- CAM ID : Determines the camera’s identification number (between 0 and 255).
-- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps.
-- UART MODE : You can select NONE, EVEN or ODD for the parity bits.
-- DISP ID : Display camera title on top left corner of the screen.
-- RET PKT : Specify whether to return the same command to the controlling device when
a control command is delivered to the camera.
-- RETURN : Select this to save the COMM ADJ menu settings and return to the
SPECIAL menu.
•• LANGUAGE : You can select the menu language according to your requirements.
•• RESET : Resets the camera settings to the factory defaults. Communication,
Language, Video Format and Monitor settings are not initialized.
•• RETURN : Select this to save the SPECIAL menu settings and return to the MAIN
SETUP menu.
EXIT
Save the current settings and exit the MAIN SETUP menu.
SCD-6021-ENGLISH-131230.indd 35
English _35
2014-3-12 15:28:25
appendix
Specification
Items
Video
Lens Type
pan / Tilt /
Rotate
Operational
Description
Video
1/3" Progressive Scan CMOS
Total Pixels
2,010(H) x 1,108(V), 2.2M Pixels
Effective Pixels
1,944(H) x 1,092(V), 2.1M Pixels
Scanning System
Progressive Scan
Min. Illumination
Color : 0.5Lux (F2.0, 50IRE), 0.008Lux (F2.0 Sen-up x60, 50IRE)
Video Output
SMPTE292M ( HD-SDI )
Lens Type
Board-in type
Mount Type
-
Max. Aperture Ratio
F2.0
Focal Length
3.8mm Fixed
Focus Control
Fixed
Angular Field of View
H: 84.5°, V: 45.8°, D: 98.8°
Pan Range
0° ~ 354°
Tilt Range
0° ~ 67°
Rotate Range
0° ~ 355°
On Screen Display
Multi-language Support
English, Korean, Japanese, Spanish, French, Portuguese, Chinese,
German, Italian, Russian, Czech, Polish, Rumanian, Serbian, Swedish,
Denish, Turkish
Camera Title
Off / On (Displayed 15 characters)
Day &Night
Auto (ICR), Color, B/W , External
Backlight Compensation Off / BLC / HLC / WDR
Contrast Enhancement
SSDR ( Off / On )
Digital Noise Reduction SSNRⅢ ( Off / On )
36_ appendix
SCD-6021-ENGLISH-131230.indd 36
2014-3-12 15:28:25
Items
Environmental
Electrical
Mechanical
Privacy Masking
Off / On (16 Rect-angle zones)
Sens-up
(Frame Integration)
Auto/Off (2x ~ 60x)
Gain Control
Off / Low / Middle / High
White Balance
ATW / Outdoor / Indoor / Manual / AWC (1,700K° ~ 11,000K°)
Electronic Shutter
Speed
Esc / A.FLK / Manual
Digital Zoom
Off / On (x2 ~ x16)
Reverse
Off / H-Rev / V-Rev / HV-Rev
Intelligent Video
Tampering, Detection,Tracking,Fixed/Moved
Communication
RS-485
Protocol
RS-485 : SAMSUNG-T, SAMSUNG-E, Pelco-D, Pelco-P, Bosch,
Honeywell, Vicon, Panasonic, GE, AD
● appendix
Operational
Description
Operating Temperature
-10°C~ +55°C (14°F~131°F) / ~90% RH
/ Humidity
Input Voltage
12VDC
Current
0.3A
Color / Material
Body : Ivory / Plastic
Dimension (ØxH)
Ø120.0 x H102.0mm (Ø4.72" X H4.02")
Weight
435g
HD-SDI
5C2V ( 75ohm )
Transmission
L-6CHD ( 75 ohm )
Distance
Max. 100~140m
Max. 200m
`` The maximum transferrable distance of HD-SDI video signal depends on the cable manufacturer or installation
conditions.
`` When a BNC cable adaptor is used to combine two or more BNC cables for distributed HD-SDI video transfer,
make sure the impedance of the adaptor is 75Ω. Otherwise, the adaptor may cause shorter transfer distance or
broken video transfer due to loss of transferred signal.
※ For enhanced performance, the product specification is subject to change without prior notice.
SCD-6021-ENGLISH-131230.indd 37
English _37
2014-3-12 15:28:26
appendix
Product Overview
Unit : mm (inch)
56.3 (2.22")
Ø 120 (4.72")
102 (4.02")
R4
4.5
(1.
75
")
38_ appendix
SCD-6021-ENGLISH-131230.indd 38
2014-3-12 15:28:26
Troubleshooting
PROBLEM
SOLUTION
Nothing appears on the screen.
yy When the camera’s HD-SDI BNC output is directly connected to the
monitor’s BNC terminal:
Make sure the monitor supports HD-SDI signal input.
● appendix
yy Check that the power cord and line connection between the camera and
monitor are properly connected.
yy When the camera’s HD-SDI BNC output is connected to the DVR: Make
sure the DVR supports HD-SDI signal input.
yy HD-SDI output is converted into other format such as DVI and VGA by
using video converter: Make sure the converter’s HD-SDI input format
supports the product’s output video format.
yy Is lens stained with dirt? Clean your lens with soft, clean cloth.
The image on the screen is dim.
yy Set the monitor to the proper condition.
yy If the camera is exposed to very strong light, change the camera position.
The image on the screen is dark.
yy Adjust the contrast feature of the monitor.
The camera is not working
properly, and the surface of the
camera is hot.
yy Check that you have properly connected the camera to an appropriate
power source.
The SENS-UP function does not
work.
yy Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
Color is not correct.
yy Check the setting of WHITE BAL SETUP menu .
yy Ensure the camera is not pointing towards the sun.
yy Is the camera framing the sun or other bright light source?
The screen flickers continually.
RS-485 communication is not
available.
SCD-6021-ENGLISH-131230.indd 39
yy HD-SDI video may not appear to be normal if distance exceeds the
maximum transferrable distance.
yy When a BNC cable adaptor is used to combine two or more BNC cables
for distributed HD-SDI video transfer, make sure the impedance of the
adaptor is 75Ω. Otherwise, it may cause shorter transfer distance or
broken video transfer.
yy Check RS-485 communication settings.
English _39
2014-3-12 15:28:26
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Samsung Techwin cares for the environment at all product manufacturing stages, and is
taking measures to provide customers with more environmentally friendly products.
The Eco mark represents Samsung Techwin’s devotion to creating environmentally friendly
products, and indicates that the product satisfies the EU RoHS Directive.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its
electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other
household waste at the end of their working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate these items from other types
of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or
their local government office, for details of where and how they can take these items for
environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the
purchase contract. This product and its electronic accessories should not be mixed with other
commercial wastes for disposal.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should
not be disposed of with other household waste at the end of their working life. Where marked, the
chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the
reference levels in EC Directive 2006/66. If batteries are not properly disposed of, these substances
can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types
of waste and recycle them through your local, free battery return system.
SCD-6021-ENGLISH-131230.indd 40
2014-3-12 15:28:27
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
Samsung Techwin R&D Center, 6, Pangyo-ro 319beon-gil, Bundang-gu, Songnam-si, Gyeonggi-do 463-400, Korea
TEL : +82-70-7147-8740~60 FAX : +82-31-8018-3745
SAMSUNG TECHWIN AMERICA Inc.
100 Challenger Rd. Suite 700 Ridgefield Park, NJ 07660
Toll Free : +1-877-213-1222 Direct : +1-201-325-6920
Fax : +1-201-373-0124
www.samsungcctvusa.com
SAMSUNG TECHWIN EUROPE LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
www.samsungtechwin.com
www.samsungsecurity.com
SCD-6021-ENGLISH-131230.indd 41
2014-3-12 15:28:27