Bosch DVR1A1081 Installation manual

EazeoRecorderInstalA.book Page 1 Tuesday, November 23, 2004 3:47 PM
DVR1A1081
Installation Instructions
EN
Digital Recorder
Installatiehandleiding
NL
Manuel d’installation
FR
Enregistreur numérique
Istruzioni sull’installazione
IT
Installationshandbuch
DE
Digital Recorder
Grabador digital
Registratore digitale
Instruções de Instalação
PT
Manual de instalación
ES
Digital Recorder
Gravador Digital
Instrukcja instalacji
PL
Cyfrowy magnetowid
EazeoRecorderInstalA.book Page 2 Tuesday, November 23, 2004 3:47 PM
ENGLISH......................................................................................................................................................................................... 3
FRANÇAIS .................................................................................................................................................................................. 23
DEUTSCH.................................................................................................................................................................................... 43
ESPAGÑOL ................................................................................................................................................................................ 63
NEDERLANDS .......................................................................................................................................................................... 83
ITALIANO .................................................................................................................................................................................. 103
PORTUGUÊS ......................................................................................................................................................................... 123
POLISH .......................................................................................................................................................................................143
EazeoRecorderInstalA.book Page 3 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Table of Contents
1.
2.
3.
4.
SAFETY PRECAUTIONS .........................................................................................................................................................5
1.1
IMPORTANT SAFEGUARDS .......................................................................................................................5
1.2
FCC INFORMATION ......................................................................................................................................6
INTRODUCTION .........................................................................................................................................................................6
2.1
FEATURES ........................................................................................................................................................6
2.2
FRONT PANEL ................................................................................................................................................7
2.3
REAR PANEL ...................................................................................................................................................8
2.3.1 Power .....................................................................................................................................................8
2.3.2 RS232 serial connector ....................................................................................................................8
2.3.3 IR remote control eye connector .....................................................................................................8
2.3.4 Alarm connections ..............................................................................................................................8
2.4
INTERCONNECTIONS ..................................................................................................................................9
2.4.1 Multiplexers ...........................................................................................................................................9
2.4.2 Quads ................................................................................................................................................. 10
2.4.3 Single camera ................................................................................................................................... 11
2.5
REMOTE CONTROL UNIT ........................................................................................................................ 12
OPERATION ............................................................................................................................................................................... 13
3.1
INSTANT RECORDING .............................................................................................................................. 13
3.2
ALARM RECORDING ................................................................................................................................. 13
3.2.1 Pre-alarm recording ......................................................................................................................... 13
3.3
NORMAL PLAYBACK ................................................................................................................................. 13
3.4
SEARCH PLAYBACK ................................................................................................................................. 13
3.5
COPY .............................................................................................................................................................. 14
3.5.1 Still image copy ................................................................................................................................ 14
3.5.2 Copy to movie file ............................................................................................................................ 14
3.6
SECURITY LOCK SETTING ..................................................................................................................... 14
MENU SET-UP .......................................................................................................................................................................... 15
4.1
MAIN MENU ................................................................................................................................................... 15
4.2
CLOCK/LANGUAGE MENU ..................................................................................................................... 15
4.3
NORMAL RECORD MENU ....................................................................................................................... 15
4.4
ALARM RECORD MENU ........................................................................................................................... 15
4.5
TIMER MENU ................................................................................................................................................. 16
4.6
BUZZER MENU ............................................................................................................................................ 16
4.7
ARCHIVE MENU ........................................................................................................................................... 17
4.8
SYSTEM SETTINGS MENU ...................................................................................................................... 17
4.9
PASSWORD MENU .................................................................................................................................... 18
Bosch Security Systems | 2004-11
EN | 3
EazeoRecorderInstalA.book Page 4 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Table of Contents
5.
SPECIFICATIONS ................................................................................................................................................................... 19
5.1
RS-232 INTERFACE ................................................................................................................................... 19
5.1.1 RS-232 control protocol ................................................................................................................ 19
5.2
RECORDING TIME ...................................................................................................................................... 20
5.3
TECHNICAL SPECIFICATIONS .............................................................................................................. 21
Bosch Security Systems | 2004-11
EN | 4
EazeoRecorderInstalA.book Page 5 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 1
1
SAFETY PRECAUTIONS
Danger
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to alert
the user to the presence of an uninsulated
“dangerous voltage” within the product's
enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
Warning
The exclamation mark within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
EN | 5
b. The equipment has been exposed to moisture.
c. The equipment has not work well or you can not
get it work according to user's manual.
d. The equipment has dropped and damaged.
e. If the equipment has obvious sign of breakage.
9. Do not leave this equipment in an environment
unconditioned, storage temperature above 50°C, it
may damage the equipment.
10. Operation Ambient 40°C
11. Power cords : Use the proper power cord with
correct attachment plug type. If the power source is
120 V AC, use a power cord that has UL and CSA
approvals. If the power source is a 240 V AC supply,
use the tandem (T blade) type attachment plug with
ground conductor power cord that meets the
respective European country's safety regulations,
such as VDE for Germany. Plug need approval with
VDE 0620, connector approval by VDE 0625,
minimum 10A, power cord H05VV-F or VW-1,0.75
mm2 x 3G should be used.
12.
Caution
To reduce the risk of electric shock, do not
remove cover (or back). No user-serviceable
parts inside. Refer servicing to qualified service
personnel.
1.1 IMPORTANT SAFEGUARDS
1. Please read these safety instructions carefully.
2. Please keep this User's Manual for later reference.
3. Please disconnect this equipment from connecter
before cleaning. Don't use liquid or sprayed
detergent for cleaning. Use moisture sheet or cloth
for cleaning.
4. Make sure the voltage of the power source when
connect the equipment to the power outlet.
5. All cautions and warnings on the equipment should
be noted.
6. Never pour any liquid into opening, this could cause
fire or electrical shock.
7. Never open the equipment. For safety reason, the
equipment should only be opened by qualified
service personnel.
8. If one of the following situations arises, get the
equipment checked by a service personnel :
a. Liquid has penetrated into the equipment.
Bosch Security Systems | 2004-11
Warning
To reduce the risk of fire or electric shock, this
apparatus should not be exposed to rain or
moisture and objects filled with liquids,such as
vases, should not be placed on this apparatus.
13. The back of the recorder should only be removed by
qualified maintenance and service personnel.
14. Danger of explosion if battery is incorrectly
replaced. A lithium battery is located inside the
enclosure of this recorder. Replace only with the
same or equivalent type. Dispose of the replaced
battery in an environmentally friendly way.
15. Keep ventilation openings free to avoid the recorder
for overheating.
16. Do not place the recorder in the immediate vicinity
of a heating source.
17. Do not install this equipment in a confined space
such as a bookcase or similar unit.
Cleaning
You can clean the unit with a moist fluff-free cloth or
shammy leather cloth.
Bosch has a strong commitment towards the
environment. This unit has been designed to respect the
environment as much as possible.
EazeoRecorderInstalA.book Page 6 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 2
1.2 FCC INFORMATION
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/ TV
technician for help.
Note
Any change or modification not expressly approved by
Bosch of the equipment authorization could void the
user's authority to operate the equipment. For additional
information or to speak to a representative, please
contact the Bosch Security Systems location nearest you
or visit our web site at www.boschsecuritysystems.com
EN | 6
2
The DVR1A1081 Digital Video Recorder provides
advanced recording and playback technology for
CCTV systems. The DVR allows uninterrrupted
recording in either continuous or time-lapse modes for
as long as a week or more. There are no video tapes to
change or store, and frequent, costly VCR maintenance
is eliminated.
The DVR can record at speeds up to 50/60 images per
second with PAL/NTSC formats and replay events
instantly. The DVR incorporates all the benefits of
digital video recording, is simple to install, and operates
just like a VCR. The highly efficient compression
technology, as well as the superior clarity and detail of
recorder images, make the DVR ideally suited for
integration with a wide range of multiplexers.
2.1 Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Bosch Security Systems | 2004-11
Introduction
Provides superior quality images
Pre-Alarm image recording
Time lapse and real time recording
Refresh rate up to 50 images for PAL and 60 images
for NTSC
Quick Search by date/time, alarm events, and
recording list
Fast and slow playback of recorded video in various
speeds
On-screen setup menu and system timer
Password protection
RS-232 communication port
Built-in M-JPEG compression/decompression with
configurable quality
Programmed with various time-lapse speeds
Data can be stored on Compact Flash Card
Remote control
Compatible with Bosch and various other types of
multiplexers.
EazeoRecorderInstalA.book Page 7 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 2
EN | 7
2.2 Front panel
1 REC: Press to start recording (red light in key lights
9 ENTER: Press to confirm a selection or a changed
when unit is recording).
data value.
2 OSD: - Press once to display the time/date, disk
usage and playback rate.
- Press a second time to display disk size,
record position and play position.
- Press a third time to switch off the onscreen display.
10 MENU: Press to enter or leave the setup menu.
11 Remote control IR receiver window.
12 ALARM: Indicator lights when an alarm occurs.
13 HDD: Indicator lights when hard disk drive is
accessed.
3 STOP: Press to stop recording or playback.
14 Compact Flash card slot: Insert a Compact Flash
4 PLAY: Press to start playback.
Card. Press the black button beside the slot to
remove the card.
5 PAUSE: Press to pause the playback picture.
6 SEARCH: Press to enter the search menu.
15 COPY: Press to copy still picture or video stream
onto Compact Flash card.
7 Shuttle Ring:
In playback mode, turn Shuttle Ring clockwise to
speed up or counterclockwise to slow down the
forward or reverse play of the picture.
In pause mode, turn Shuttle Ring to move the
picture slowly forward or reverse.
8 Jog Dial:
In playback mode, turn Jog Dial to select the
playback speed.
In pause mode, turn Jog Dial to move forward or
backward image by image.
In menu mode, turn Jog Dial to navigate through
the menu pages or to select data values. Use
together with the ENTER key to set menu values.
1
15
14
Bosch Security Systems | 2004-11
13 12
2
3
4
5
6
11
10
7
8
9
EazeoRecorderInstalA.book Page 8 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 2
EN | 8
2.3 Rear panel
* Signal
- switching voltage High: > 2 Vdc
2.3.1 Power
- switching voltage Low: < 0.5 Vdc
Connect the power suppy cable to the power socket at
the rear of the unit. Use the power switch to switch the
unit ON or OFF.
GND
NC4
NC3
DISKFULL
VEXT
ALM-CO
ALM-NO
ALM-NC
GND
GND
NC2
NC1
REC
ALM-RST
GND
ALM-IN
- max. input voltage: 12 Vdc
2.3.2 RS232 serial connector
Connect D-Sub 9-pin connector to the RS232 port if
you want to control the unit remotely.
2.3.3 IR remote control eye connector
If the remote control IR receiver window at the front is
hidden from view (if the unit is mounted in a cupboard),
connect the optionally available extension IR cable to
the remote control connector. Position the receiver eye
so that it is in line-of-sight of the remote control unit.
2.3.4 Alarm connections
The ALM-IN and ALM-RST inputs can be set to
Normally Open (N.O.) or Normally Closed (N.C.) in
the Alarm record menu.
GND:
ALM-IN:
ALM-RST:
REC:
NC1, NC2:
Ground connection.
Apply a signal* here to start alarm
recording.
Apply a signal* here to stop alarm
recording.
A high level external recording request
signal* applied to this pin starts
recording. When the signal drops to low,
recording stops.
No connections.
The alarm output signals are:
GND:
ALM-NC**:
Ground connection.
When an alarm occurs, the connection
between this pin and ALM-COM is
open. Otherwise it is closed.
ALM-NO**: When an alarm occurs, the connection
between this pin and ALM-COM is
closed. Otherwise it is open.
ALM-COM**: Alarm common contact.
VEXT:
Synchronization signal for multiplexer.
Output voltage: 5 Vdc
Output current: 100mA
DISKFULL: Disk full alarm output signal.
Output voltage: 5 Vdc
Output current: 100mA
NC3, NC4:
No connections.
* * contact voltage max: 24 Vdc
max. switching current: 2A dc
IR remote
control eye
connector
RS-232
connector
Power switch
Power
Alarm outputs
Alarm inputs
Mux main
Monitor In
Video
In
Looping out
Monitor Out
Out 1
Out 2
RS 232
Remote Control
GND
VEXT
Alarm connector
100-240 Vac
Bosch Security Systems | 2004-11
GND
NC4
NC3
DISKFULL
VEXT
ALM-CO
ALM-NO
ALM-NC
GND
GND
NC2
NC1
REC
ALM-RST
GND
AC 100-240
ALM-IN
Off
EazeoRecorderInstalA.book Page 9 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 2
EN | 9
2.4 Interconnections
•
The DVR can be connected to a wide range of
multiplexers, quads or directly to a camera.
2.4.1 Multiplexers
The drawing below shows how to connect a multiplexer
to the DVR.
•
•
Connect the monitor to the BNC socket marked
Monitor Out on the rear of the DVR.
Connect the main monitor output of the multiplexer
to the BNC socket marked Monitor In on the rear of
the DVR.
Connect the VCR output of the multiplexer to the
BNC socket marked Video In on the rear of the
DVR.
• Connect the VCR input of the multiplexer to the
BNC socket marked Video Out on the rear of the
DVR.
• To synchronise switching with the multiplexer
connect the VEXT and GND connections on the
rear of the unit to the connector of the multiplexer.
When the connections are made, refer to the system
menu to select the type of multiplexer you are using.
Cameras
Multiplexer
1
VCR OUT VCR IN
2
3
4
5
IR remote
control eye
connector
RS-232
connector
Power switch
Power
6
VCR
Monitor
MON B MON A
Mux main
Monitor In
Video
In
Looping out
Monitor Out
Out 1
Out 2
RS 232
Remote Control
Monitor Out
GND
100-240 Vac
Monitor
Bosch Security Systems | 2004-11
VEXT
GND
NC4
NC3
DISKFULL
VEXT
ALM-CO
ALM-NO
ALM-NC
GND
GND
NC2
NC1
REC
ALM-RST
GND
AC 100-240
ALM-IN
Off
EazeoRecorderInstalA.book Page 10 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 2
EN | 10
2.4.2 Quads
•
Connect the video output of the multiplexer to the
BNC socket marked Video In on the rear of the
DVR.
• In the system menu set the multiplexer item to Off.
To connect a quad with a VCR output, refer to the
multiplexer connections.
The drawing below shows how to connect a quad
without a VCR output to the DVR.
•
Connect the monitor to the BNC socket marked
Monitor Out on the rear of the DVR.
Quad
1
2
3
4
Video
Video OUT
Power switch
Power
Mux main
Monitor In
Video
In
Looping out
Monitor Out
Out 1
Out 2
RS-232
connector
IR remote
control eye
connector
RS 232
Remote Control
Monitor Out
GND
100-240 Vac
Monitor
Bosch Security Systems | 2004-11
VEXT
GND
NC4
NC3
DISKFULL
VEXT
ALM-CO
ALM-NO
ALM-NC
GND
GND
NC2
NC1
REC
ALM-RST
GND
AC 100-240
ALM-IN
Off
EazeoRecorderInstalA.book Page 11 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 2
EN | 11
2.4.3 Single camera
•
The drawing below shows how to connect a single to
the DVR.
•
•
Connect the video output of the camera to the BNC
socket marked Video In on the rear of the DVR.
In the system menu set the multiplexer item to Off.
Connect the monitor to the BNC socket marked
Video Out on the rear of the DVR.
Video In
Camera
Power switch
Power
IR remote
control eye
connector
RS-232
connector
Mux main
Monitor In
Video
In
Looping out
Monitor Out
Out 1
Out 2
RS 232
Remote Control
Video Out
GND
100-240 Vac
Monitor
Bosch Security Systems | 2004-11
VEXT
GND
NC4
NC3
DISKFULL
VEXT
ALM-CO
ALM-NO
ALM-NC
GND
GND
NC2
NC1
REC
ALM-RST
GND
AC 100-240
ALM-IN
Off
EazeoRecorderInstalA.book Page 12 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 2
EN | 12
2.5 Remote control unit
The remote control unit is an accessory that makes it
easy to control the DVR from a distance. You can carry
out the main operations using the remote control unit.
The keypad functions for the DVR are as follows:
RECORD:
STOP:
PLAY:
SEARCH:
Press to start recording.
Press to stop recording or playback.
Press to start playback.
Increase the speed by 2x, 4x, 8x, 16x,
32x, 640x, 2x . . .
REWIND:
In playback mode, press to reverse
playback (Search key increases reverse
speed).
STEP REW.: Press to stop playback. Press again to
step backward image by image.
STEP FORW.:Press to stop playback. Press again to
step forward image by image.
FORWARD: In reverse playback, press for forward
playback (Search key increases forward
speed).
Bosch Security Systems | 2004-11
0
BOSCH
DVR control keys
EazeoRecorderInstalA.book Page 13 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 3
3
Operation
3.1 Instant recording
Press the Record key to start the recording immediately
- the images are recorded on the hard disk.
• The recording rate and recording quality are set in
the Normal record and Alarm record menus.
Press the Stop key to stop recording.
• Stop key can only be activated in recording mode.
• When the hard disk is full, the DVR stops recording
automatically or overwrites from the beginning of
the hard disk depending on the setting in the System
Settngs menu.
3.2 Alarm recording
The monitor image is recorded automatically when an
alarm occurs and stops recording at the end of the alarm
duration period. Instant recording and timer recording
stop when an alarm occurs. If the unit is already
recording then the recording quality does not change for
alarm recording. Set the options for alarm recording in
the Alarm record menu.
3.2.1 Pre-alarm recording
A buffer is used to pre-capture video for
recording images just before an alarm is triggered.
Pre-alarm recording only occurs if the unit is not already
recording during the pre-alarm period. The recording
quality in the pre-alarm period is the same as the
recording quality before the alarm occurs. If the
recorder is not recording before the alarm occurs, the
recording quality in the pre-alarm period is the same as
normal recording quality.
3.3 Normal playback
Playback
• Press PLAY key to start playing back the stored
image from the last segment.
• Press STOP key to stop playing back.
Fast Forward
• Press PLAY key to start playing back.
• Turn the Shuttle Ring clockwise and fast forward
playback starts. The speed is shown on the OSD
(normal play speed, 2x, 4x, 8x, 16x, 32x, 640x).
Reverse Playback
• Press PLAY key to start playing back.
Bosch Security Systems | 2004-11
EN | 13
•
Turn the Shuttle Ring counterclockwise and fast
reverse playback starts. The speed is shown on the
OSD (normal play speed, 2x, 4x, 8x, 16x, 32x, 640x).
Slow Forward Playback
• Press Pause key to freeze the playing back picture.
• Turn the Shuttle Ring clockwise and slow forward
playback starts. The speed is shown on the OSD
(>1/2, 1/4, 1/8, 1/16, 1/32, 1/64).
Slow Reverse Playback
• Press Pause key to freeze the playing back picture.
• Turn the Shuttle Ring counterclockwise to start slow
reverse playback. The speed is shown on the OSD
(<1/2, 1/4, 1/8, 1/16, 1/32, 1/64).
Lock displayed speed
• To lock the displayed speed, press the Enter key and
then release the Shuttle Ring. If you turn the Shuttle
Ring again, the speed returns to normal play speed.
Image advance Forward/Reverse
• Press Pause key to freeze the picture.
• Turn the Jog Dial clockwise to advance the picture
image by image.
• Turn the Jog Dial counterclockwise to rewind the
picture image by image.
• The image speed increases if the Jog Dial is turned
quickly.
3.4 Search playback
Segment Search Playback
• Press the Search key to enter the Search menu.
• Move the cursor to BY SEGMENT LIST and press
the Enter key to select file search.
• Move the cursor to the segment you want to
playback (pAlarm: Pre-alarm record, Timer: Timer
record).
• If the selection list is full, turn the Jog Dial clockwise
to select the next page list.
• Press Enter to start playing back.
Alarm Search Playback
• Press Search key to enter the Search menu.
• Move the cursor to BY EVENT LIST and press the
Enter key to select alarm search.
• Move the cursor to select the alarm image to be
played back.
• If the selection list is full, turn the Jog Dial clockwise
to select the next page list.
• Press Enter to start playing back the alarm images.
EazeoRecorderInstalA.book Page 14 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 3
•
The alarm image is played back from the pre-alarm
period and stops at the end of alarm duration.
Date/Time Search Playback
• Press Search key to enter the Search menu.
• Move the cursor to BY DATE/TIME and press the
Enter key to select file search.
• Move the cursor to the value you wish to select and
press the Enter key.
• Turn the Jog Dial to increase or decrease the value
and press the Enter key.
• Move the cursor to START SEARCH AND PLAY
and press the Enter key and the playback starts from
the date/time set in the menu.
EN | 14
Copied images are stored as a single picture in a JPG
file format.
3.5.2 Copy to movie file
•
•
•
•
•
•
•
Press the Play key to start playing back.
Press the Copy key to enter the copy mode.
Turn the Jog Dial to select the desired camera.
While the image is displayed, press the Copy key
again. The message "Copying …" appears on the
screen during the process.
Press STOP key to end copy.
The message "Success" and the file identification
appears on the screen after the file is copied.
Press the Play key to continue playback.
If there is no image stored in the date/time specified
then the unit automatically starts playing back from the
nearest set time.
Copied images are stored as a movie picture in a MOV
file format.
3.5 Copy
3.6 Security lock setting
Insert a Compact Flash card (type I or II) into the
Compact Flash slot on the front panel. When inserting
the Compact Flash card, make sure that the direction of
insertion is correct. Use only a Compact Flash card with
a capacity of 16MB or higher.
Press the REC key for more than 5 seconds while in the
record mode to lock all the keys on the front panel. (The
Password must be set in the System Settings Menu to
enable this feature.)
Press Stop key, the system asks for the password. If you
enter the correct password, the locked keys are released.
The Compact Flash copy function is designed for
copying short clips. A long clip can take quite a long
time to copy.
Note
To improve the legibility of the copy messages, press
the OSD key. Press the OSD key again to switch off the
background.
3.5.1 Still image copy
•
•
•
•
•
•
•
•
Press the Play key to start playing back.
Press the Pause key to freeze the picture.
Turn the Jog Dial clockwise or counterclockwise to
move to the desired image.
Press the Copy key to enter the copy mode.
Turn the Jog Dial to select the desired camera image.
While the image is displayed, press the Copy key
again. The message "Copying …" appears on the
screen during the process. The message "Success"
and the file identification appears on the screen after
the file is copied.
Press the STOP key to cancel copy.
Press the Play key to continue playback.
Bosch Security Systems | 2004-11
EazeoRecorderInstalA.book Page 15 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 4
4
EN | 15
Menu set-up
4.3 Normal record menu
When system has been connected as described:
• Switch power on
• Allow some time for the system to load.
• Press the MENU key to enter the MAIN MENU.
When the main menu is displayed you see the different
submenus where the settings can be changed.
To navigate through these menus, turn the Jog Dial
clockwise or counterclockwise to scroll through the
submenus. Press the ENTER key to open a submenu. In
the submenus, continue using the Jog Dial and ENTER
key to scroll through items and values and select them.
To return to the main menu, scroll to the bottom of each
submenu to the MAIN MENU item and select it by
using the ENTER key.
4.1 Main menu
NORMAL RECORD MENU
RECORD SPEED
RECORD QUALITY
8 IPS
STANDARD
RECORD TIME
... HRS
MAIN MENU
>
SPEED : Select the record speed from 0.1 to 25/30 IPS.
QUALITY: There are six quality levels for recording
LOWER 15 KB
LOW: 20 KB
BASIC: 25 KB
STANDARD: 30 KB
HIGH: 35 KB
SUPERIOR: 40 KB
RECORD TIME: Shows an estimate of the recording time available on
disk for the selected speed and quality.
4.4 Alarm record menu
MAIN MENU
ALARM RECORD MENU
CLOCK/LANGUAGE
NORMAL RECORD
ALARM RECORD
TIMER
BUZZER
ARCHIVE
SYSTEM SETTING
>
>
>
>
>
>
>
4.2 Clock/Language menu
ALARM OPERATION
RECORD SPEED
RECORD QUALITY
ALARM-IN TYPE
ALARM-RESET TYPE
ALARM DURATION TIME
ON
50 IPS
STANDARD
N.O.
N.O.
10 SECS
PRE-ALARM OPERATION
RECORD SPEED
ON
50 IPS
CLOCK/LANGUAGE MENU
MAIN MENU
DATE
TIME
DATE FORMAT
MENU LANGUAGE
2002-04-24
13:01:02
YYYY-MM-DD
ENGLISH
MAIN MENU
>
DATE: Year: 2000~2099 Month: 01~12 Date: 01~31
TIME: Hour: 00~23 Minute : 00~59 Second: 00~59
DATE FORMAT: Set the display order for Year (YYYY), Month (MM)
and Day (DD)
MENU LANGUAGE: English, German, French, Spanish, Italian,
Portuguese, Dutch or Polish.
MAIN MENU: Return to the main menu.
Bosch Security Systems | 2004-11
>
ALARM OPERATION:
ON : Record when alarm occurs.
OFF : Do not record when alarm occurs.
RECORD SPEED: Recording speed for the duration of the alarm.
The max. recording speed is 50/60 IPS (PAL/NTSC).
The min. recording speed is 0.1 IPS.
RECORD QUALITY: Recording picture quality when alarm occurs.
LOWER: 15 KB
LOW: 20 KB
BASIC: 25 KB
STANDARD: 30 KB
HIGH: 35 KB
SUPERIOR: 40 KB
ALARM-IN TYPE:
N.O. : Normally Open
N.C. : Normally Closed
ALARM-RESET TYPE:
N.O. : Normally Open
N.C. : Normally Closed
EazeoRecorderInstalA.book Page 16 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 4
EN | 16
ALARM DURATION TIME: Alarm recording starts from the beginning
of alarm and stops at the end of the duration or when alarm
reset is activated. The max. duration is non-stop, the min.
duration is 10 seconds.
PRE-ALARM OPERATION:
ON: Record the picture in pre-alarm recording speed in prealarm period.
OFF: No pre-alarm recording before alarm occurs.
RECORD SPEED: The recording speed in the pre-alarm period.
The max. recording speed is 50/60 IPS (PAL/NTSC).
The min. recording speed is 0.1 IPS.
Note
If the alarm occurs in standby or normal recording
mode, the recording quality is the same as the normal
recording quality. If the alarm occurs in timer recording
mode, the recording quality is the same as the value set
in timer recording quality.
4.5 Timer menu
The monitored image can be recorded automatically by
setting the start and end times in the TIMER MENU.
There are 15 entries where a recording schedule for a
particular day or set of days can be set for the week.
Move to an entry and press enter to select the day.
If you program for example the following:
START 09:00, STOP 23:59
Than recording starts at 09:00:00 and stops at 23:59:59.
To stop a timed recording while it is recording, press
the STOP key to enter the TIMER MENU and change
the SET value to OFF.
START: Enter the start time for timer recording.
STOP: Enter the end time for timer recording.
STOP time needs to be later than the START time.
(e.g. START 16.00, STOP 03.00 is not correct
START 16.00, STOP 00.00 is not correct
START 16.00, STOP 23.59 is correct
SPEED: When SPEED FORMAT set by HOUR, the recording speed
can be set from 4/6 (NTSC/PAL) HR to 960HR.
When SPEED FORMAT set by IPS, the recording speed can
be set from 0.1~30/0.1~25(NTSC/PAL)IPS.
QUALITY: There are six recording picture quality levels
LOWER: 15 KB
LOW: 20 KB
BASIC: 25 KB
STANDARD: 30 KB
HIGH: 35 KB
SUPERIOR: 40 KB
SET:
Set ON when using timer recording.
Set OFF when not using timer recording.
In Timer Recording mode, the OSD shows the Timer
date/time and the Timer recording rate appears under
T.REC.
You cannot change the quality level for continuous
recording. For example:
Seg 1 08:30~17:00
Seg 2 17:00~23:59
Seg 1 and Seg 2 are treated as the continuous recording
08:30~23:59.
If you need to set different quality level, set as follows:
Seg 1 08:30~16:59
Seg 2 17:00~23:59
4.6 Buzzer menu
TIMER MENU
BUZZER MENU
WEEK
SUN
MON
WDAY
WEND
DLY
MON
TUE
FRI
THU
WED
SAT
SUN
START
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
STOP
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
00:00
SPEED
002 HR
002 HR
002 HR
002 HR
002 HR
002 HR
002 HR
002 HR
002 HR
002 HR
002 HR
002 HR
QUALITY
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
STANDARD
MAIN MENU
WEEK: Selects the day or set of days for the timer.
DLY: every day
WDAY: Monday to Friday
WEND: Saturday and Sunday
Individual days of the week
Bosch Security Systems | 2004-11
SET
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
>
BUZZER OPERATION
ALARM-IN
RECORD-IN
DISK FULL
VIDEO LOSS
TIMER
MAIN MENU
ENABLE
ON
ON
ON
ON
OFF
>
BUZZER OPERATION:
ENABLE: Select buzzer to be on.
DISABLE: Select buzzer to be off.
Note: Press Enter button to enable/disable in Record/Playback
mode.
ALARM-IN: ON - the buzzer sounds when the alarm occurs.
RECORD-IN: ON - the buzzer sounds when Record-IN signal is
applied on the Record-IN terminal.
DISK FULL: ON - the buzzer sounds when disk is nearly full 99.7%
VIDEO LOSS: ON - the buzzer sounds when the video signal is lost.
TIMER: ON - the buzzer sounds when timer record occurs.
EazeoRecorderInstalA.book Page 17 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 4
EN | 17
4.7 Archive menu
ARCHIVE MENU
PICTURE SIZE
TIME STAMP
TIME STAMP POSITION
WATER MARK
WATER MARK POSITITON
720 X 576
ON
BOTTOM
ON
BOTTOM
MAIN MENU
>
PICTURE SIZE: Select picture size for copying image to CF card
Big size: 720x576 (PAL), 720x480 (NTSC)
Small size: 352x288 (PAL), 352x240 (NTSC)
TIME STAMP:
ON: Time stamp appears on the picture when copying image
to CF card.
OFF: Time stamp does not appear on the picture when
copying image to CF card.
TIME STAMP POSITION:
BOTTOM: Time stamp appears at the bottom
TOP: Time stamp appears at the top
WATER MARK:
ON: Water mark appears on the picture when copying image
to CF card.
OFF: Water mark does not appear on the picture when
copying image to CF card.
WATER MARK POSITION:
BOTTOM: Water mark appears at the bottom
TOP: Water mark appears at the top.
4.8 System settings menu
When YES is set for PASSWORD ENABLE, a password is
required to enter the menu. The code is six digits long and
can be any digit from 1 to 5.
If you have activated the password, whenever you press the
menu button in live mode or stop button in record mode the
system asks you to enter the password. Therefore, be sure to
make a note of the password.
MULTIPLEXER: The following settings are available:
OFF: Select if only one camera is connected to the DVR. The
main monitor output is same as the video out connector all
the time.
MAKE OF MULTIPLEXER: Selection for various types of
multiplexer (e.g. BOSCH LTC2600). When a multiplexer is
selected, the video input from the MUX MAIN MONITOR
connector at the rear panel is looped through to the
MONITOR OUT when the recorder is not in MENU mode.
UNKNOWN: Select if your multiplexer is not listed and you
don’t have a custom code.
CUSTOM: Select if you have a custom code for your
multiplexer model. Enter the parameters in the CUSTOM
MULTIPLEXER PARAMETER menu.
CUSTOM MULTIPLEXER MENU
PARAMETER
PARAMETER
PARAMETER
PARAMETER
PARAMETER
PARAMETER
PARAMETER
PARAMETER
PAIR
PAIR
PAIR
PAIR
PAIR
PAIR
PAIR
PAIR
1
2
3
4
5
6
7
8
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
000
SYSTEM SETTINGS MENU
>
SYSTEM SETTINGS MENU
PASSWORD ENABLE
PASSWORD
MULTIPLEXER
FIELD CODE LINE
DISK FULL
SPEED FORMAT
VIDEO SYSTEM
PARAMETER PAIR:
In the CUSTOM MULTIPLEXER menu, you can fill-in a
custom code for a particular model of multiplexer. Consult
you sales representative for information on these codes.
NO
555555
Bosch LTC2600
13
REWRITE
BY IPS
PAL
ERASE DISK
SYSTEM UPDATE
LOAD DEFAULT
CF FORMAT
>
>
>
>
MAIN MENU
>
PASSWORD ENABLE:
YES: PASSWORD required to enter the menu.
NO: PASSWORD not required to enter the menu.
PASSWORD :
Bosch Security Systems | 2004-11
FIELD CODE LINE:
If you set the multiplexer make to UNKNOWN, you can
adjust the field code line of the connected multiplexer
between 0 and 20. The default (13) is suitable for most
multiplexers. If the field code line appears at the top of the
playback channels, decrease the value. If multiplexers do not
playback correctly, increase the value.
DISK FULL:
STOP : When disk is full, the machine stops recording.
REWRITE : When disk is full, the current video overwrites the
existing video from the beginning of the hard disk.
SPEED FORMAT: Select recording speed by IPS (Images per
second) or Hour
VIDEO SYSTEM: Select the video system NTSC or PAL (requires
power reset to activate).
EazeoRecorderInstalA.book Page 18 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 4
ERASE DISK:
Press Enter to erase all recording from the hard disk.
The confirmation dialog box appears on the screen.
Select Yes or No and then press ENTER.
SYSTEM UPDATE:
Press Enter to update the system or not.
YES: Copy the update file onto the Compact Flash card on
the PC and then insert the Compact Flash card into the slot.
Press ENTER key to update the system. After the system is
updated successfully, be sure to reset the power to activate.
LOAD DEFAULT:
Press Enter to load the factory default or not.
YES: The confirmation dialog box appears on the screen.
Select Yes or No and then press ENTER.
CF FORMAT:
YES: will format the Compact Flash card.
NO: will not format the Compact Flash card.
Bosch Security Systems | 2004-11
EN | 18
4.9 Password menu
When password protection is enabled, a password menu
appears on the screen when you try to open a menu or
stop recording. You must enter the password using the
following keys:
REC : 1
OSD : 2
STOP : 3
PLAY : 4
PAUSE : 5
EazeoRecorderInstalA.book Page 19 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 5
5
EN | 19
Specifications
5.1 RS-232 interface
The DVR can be controlled by a computer or a
terminal via the standard D-SUB 9-pin RS-232
connector.
ASCII FUNCTION
CODE
Keypad in
front panel
K01
Start Recording
REC
K03
Stop Recording and
Playing back
STOP
K04
Playing back
PLAY
Pin
DVR1C1161
1
NC
2
TXD
Pin
HOST
1
2
NC
RXD
K05
Pause the playback
picture
PAUSE
3
3
TXD
K06
Search playback
SEARCH
Copy picture into
CF card
COPY
RXD
4
5
NC
GROUND
4
5
DTR
GROUND
K00
6
7
8
9
NC
NC
NC
+5V
6
7
8
9
DSR
RTS
CTS
NC
K02
On screen display
DISPLAY
K07
Confirm the
selection
ENTER
K08
Enter Setting Menu
MENU
K09K15
Fast reverse
playback speed
<< 1-640 X,
1/2-1/64
The transmission setting is 9600 baud rate, 8 data bits, 1
start bit, 1stop bit and no parity.
5.1.1 RS-232 control protocol
A computer or a terminal can be used to control the unit
by sending three character ASCII commands through
the RS232 connector, these ASCII commands are
started with 'K' or 'k'. There are 30 ASCII commands
mapped to the 30 keypads in the front panel. The 30
ASCII commands are shown on the following table.
Bosch Security Systems | 2004-11
K16 - Fast playback speed >> 1-640 X,
K22
1/2-1/64
K23
Rewind the still
image
JOG-REW
K24
Advance the still
image
JOG-FF
EazeoRecorderInstalA.book Page 20 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 5
EN | 20
5.2 Recording time
Approximate recording times in hours when recording
with a 80-GB hard disk.
PAL
Recording
Rate
(IPS)
Recording
Speed
(Hour)
Lower
(15KB)
Low
(20KB)
50
25
12
8
5
2
1.6
1.0
0.5
0.2
0.1
3
6
18
30
48
72
120
168
240
480
960
30
59
119
178
296
711
948
1481
2963
7407
14815
22
44
89
133
222
533
711
1111
2222
5556
11111
Recording
Rate
(IPS)
Recording
Speed
(Hour)
Lower
(15KB)
Low
(20KB)
60
30
20
10
5
2
1.5
1.0
0.5
0.2
0.1
3
6
18
30
48
72
120
168
240
480
960
25
49
74
148
296
741
988
1481
2963
7407
14815
19
37
56
111
222
556
741
1111
2222
5556
11111
Picture Quality (average file size)
Basic
Standard
High
(25KB)
(30KB)
(35KB)
Approximate Recording Time
Hours / weeks
18
15
13
36
30
25
71
59
51
107
89
76
178
148
127
427
356
305
569
474
406
889
741
635
1778
1481
1270
4444
3704
3175
8889
7407
6349
Superior
(40KB)
11
22
44
67
111
267
356
556
1111
2778
5556
NTSC
Reference:
24H=1 day, 168H=1 week, 720H=1 month,
8760H=1year
(Estimated with typical image-low noise level)
Bosch Security Systems | 2004-11
Picture Quality (average file size)
Basic
Standard
High
(25KB)
(30KB)
(35KB)
Approximate Recording Time
Hours / weeks
15
12
11
30
25
21
44
37
32
89
74
63
178
148
127
444
370
317
593
494
423
889
741
635
1778
1481
1270
4444
3704
3175
8889
7407
6349
Superior
(40KB)
9
19
28
56
111
278
370
556
1111
2778
5556
EazeoRecorderInstalA.book Page 21 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 5
EN | 21
5.3 Technical specifications
Video
Format
Input
Output
Compression
Resolution
Display
General
PAL/NTSC
1 camera input (BNC), 1Vpp,
75Ohm
1 video output (BNC) for main
monitor, 1Vpp, 75Ohm
M-JPEG
720 x 576 (PAL) /
720 x 484 (NTSC)
Full display for live and playback
Alarm
Input
Output
Switching voltage High: > 2 Vdc
Switching voltage Low: < 0.5 Vdc
One relay output:
Contact voltage max.: 24 Vdc
Switching current max.: 2A dc
Storage
Hard disk
80 Gb
Recording
Mode
Rate
Continuous, time-lapse, schedule or
event recording
Max. 50 images per sec. (PAL)
Max. 60 images per sec. (NTSC)
Playback
Rate
Search
Max. 50 images per sec. (PAL)
Max. 60 images per sec. (NTSC)
Date/time, segment list or event
(alarm)
Video loss detection Yes
Power loss detectionYes
Alarm log
Yes
User interface
Menu-driven
Setup
By on-screen display menu
User input device Front panel keypad, remote control
(IR with wired receiver) optional
Image export
Built-in Compact Flash slot for
Type I and Type II cards
Security
Password protection
Power supply
100 - 240 Vac, 50/60 Hz
Power consumption < 40 W
Timer
Weekly timer, built-in real time clock
Control connection RS-232, 9-pin D-Sub connector
Mechanical
Weight
approx. 5.5 kg / 11.5 lbs
Dimensions (WxHxD)346 x 88 x 269 mm
13.6 x 3.5 x 10.5 inches
Ambient temperature
Operating
+0°C … +40°C
+32°F . . . +104°F
Approvals
Safety
Europe
USA
Australia
EN60950
UL60950 UL & cUL listed
C-Tick
Electro Magnetic Compatibility (EMC)
Europe
USA
Australia
EN55022 Class B, EN50130-4
FCC part 15, class B
AS/NZS 3548
Specifications may change without notice. If you have
any problems, contact your dealer.
Bosch Security Systems | 2004-11
EazeoRecorderInstalA.book Page 22 Tuesday, November 23, 2004 3:47 PM
DVR1A1081 | Installation Manual | Chapter 5
Bosch Security Systems | 2004-11
EN | 22