Zanussi FL 811 Operating instructions

AUDIO/VIDEO MULTI-CHANNEL
RECEIVER
VSX-D711
VSX-D811S
Operating Instructions
XRB3013A.01.06
1
01.12.12, 4:40 PM
Thank you for buying this Pioneer product.
Please read through these operating instructions
so you will know how to operate your model
properly. After you have finished reading the
instructions, put them away in a safe place for future
reference.
IMPORTANT NOTICE
H006AEn
The serial number for this equipment is located in the
rear panel. Please write this serial number on your
enclosed warranty card and keep it in a secure area.
This is for your security.
XRB3013A.01.06
2
01.12.12, 4:40 PM
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic II” and the double D symbol 2
are trademarks of Dolby Laboratorories.
XRB3013A.01.06
3
"DTS", “ES”, and "DTS Digital Surround" are trademarks
of Digital Theater Systems, Inc.
01.12.12, 4:41 PM
Contents
1 Before you start
Checking what’s in the box ...............................6
Installing the receiver ........................................6
Making cable connections ................................6
Loading the batteries .........................................6
Operating range of remote control unit ........... 6
2 5 minute guide
Introduction to home theater ............................7
Listening to Surround Sound ............................8
Using the Quick Setup ....................................12
3 Connecting up
Audio/Video cords ........................................... 13
S-video cables ...................................................13
Component video cords ................................. 13
Digital audio coaxial cords/
Optical cables ...................................................13
Connecting digital components .................... 14
Connecting audio components ......................16
Connecting DVD 5.1 channel components ... 17
Connecting video components .......................18
Connecting to the front panel
video terminal ............................................ 18
Connecting antennas ..................................... 19
FM wire antenna .........................................19
AM loop antenna ....................................... 19
Antenna snap connectors ........................ 19
Using external antennas ............................19
To improve FM reception ............................19
To improve AM reception ...........................19
Connecting the speakers (VSX-D711) ............. 20
Connecting the speakers (VSX-D811S) ........... 21
A and B speaker systems ......................... 22
Speaker terminals ..................................... 22
Hints on speaker placement .................... 22
Connecting additional amplifiers
(VSX-D811S only) ............................................ 24
AC outlet .......................................................... 25
Operating other Pioneer components .......... 25
XRB3013A.01.06
4
4 Controls and displays
Front panel ........................................................26
Display ............................................................. 27
Remote control ................................................ 29
5 Playing sources
Introduction to Sound Modes ........................ 32
Stereo/Direct ...............................................32
Standard mode .......................................... 32
Advanced Surround modes .......................33
Choosing the input signal .............................. 34
Listening to multi-channel playback ..............34
Using Stereo/Direct .........................................35
Using Advanced Surround ............................. 35
Using Loudness and Midnight listening ........36
Using the tone controls .................................. 36
Playing other sources ..................................... 36
Selecting the multi-channel analog inputs ... 37
6 Setting up your receiver
Choosing your receiver setup ........................ 38
Speaker setting .......................................... 39
Surround back speaker
setting (VSX-D811S only) ............................ 40
6.1 channel setting (VSX-D811S only) ....... 40
Subwoofer setting ..................................... 40
Crossover frequency setting ......................40
LFE attenuator setting ................................41
Front speaker distance setting ..................41
Center speaker distance setting .............. 41
Surround speaker distance setting .......... 41
Surround back speaker distance
setting (VSX-D811S only) ............................ 42
Dynamic range control setting ..................42
Dual mono setting ..................................... 42
Component video input settings .............. 42
Surround back channel input
setting (VSX-D811S only) ............................ 43
Coaxial digital input settings .................... 43
Optical digital input settings .................... 43
01.12.12, 4:41 PM
Setting the relative volume level
of each channel ............................................... 44
7 Using the tuner
Listening to the radio ...................................... 45
Improving FM stereo sound ....................... 45
Tuning directly to a station ........................ 45
Saving station presets .....................................46
Naming station presets .................................. 47
Listening to station presets ............................ 47
8 Making a recording
Making an audio or a video recording .......... 48
Monitoring your recording ........................ 48
9 Controlling the rest of your system
Setting the remote to control
other components ........................................... 49
Selecting preset codes directly ....................... 49
Searching for preset codes ............................ 50
Programming signals from other
remote controls (VSX-D811S only) .................. 50
Erasing one of the remote control
button settings (VSX-D811S only) ................... 51
Clearing all the remote control settings ........ 51
Direct function ................................................ 52
Confirming preset codes .................................52
Controls for TVs ............................................... 53
Controls for other components ....................... 54
Preset Code List ...............................................56
10 Additional information
Troubleshooting ............................................... 68
Specifications ...................................................70
XRB3013A.01.06
5
01.12.12, 4:41 PM
01
Before you start
Checking what’s in the box
Please check that you've received the following
supplied accessories:
• AM loop antenna
• FM wire antenna
Incorrect use of batteries may result in such
hazards as leakage and bursting. Observe the
following precautions:
• Never use new and old batteries together.
• Dry cell batteries x 2 (AA size IEC R6P)
• These operating instructions
• Insert the plus and minus sides of the
batteries properly according to the marks
in the battery case.
Installing the receiver
• Batteries with the same shape may have
different voltages. Do not use different
batteries together.
• Remote control
Please note the following points:
• Do not place objects
directly on top of this
unit. This prevents
proper heat dispersal.
• When installing on a
rack, shelf, etc., be sure to leave more than
8 inches (20 cm.) of space above the
receiver.
Making cable connections
Make sure not to
bend the cables
over the top of this
unit (as shown in
the illustration). If
this happens, the
magnetic field
produced by the transformers in this unit may cause a humming
noise from the speakers.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules
that apply in your country or area.
Operating range of remote
control unit
The remote control may not work properly if:
• There are obstacles between the remote
control and the receiver's remote sensor.
• Direct sunlight or fluorescent light is
shining onto the remote sensor.
• The receiver is located near a device that is
emitting infrared rays.
• The receiver is operated simultaneously
with another infrared remote control unit.
Loading the batteries
30
30
23ft (7m)
6
Dry cell batteries x 2 (AA size IEC R6P)
En
XRB3013A.01.06
6
01.12.12, 4:41 PM
5 minute guide
02
Introduction to home theater
You are probably used to using stereo equipment to listen to music, but may not be used to home
theater systems that give you many more options (such as surround sound) when listening to
soundtracks.
Home theater refers to the use of multiple audio tracks to create a surround sound effect, making
you feel like you're in the middle of the action or concert. The surround sound you get from a home
theater system depends not only on the speakers you have set up in your room, but also on the
source and the sound settings of the receiver.
DVD-Video has become the basic source material for home theater due to its size, quality, and ease
of use. Depending on the DVD, you can have up to seven different audio tracks coming from one
disc, all of them being sent to different speakers in your system. This is what creates a surround
sound effect and gives you the feeling of ‘being there’.
This receiver will automatically decode Dolby Digital, DTS, or Dolby Surround DVD-Video discs,
according to your speaker setup. In most cases, you won’t have to make changes for realistic
surround sound, but other possibilities (like listening to a CD with multi-channel surround sound)
are explained in Playing sources, starting on page 32.
7
En
XRB3013A.07.12
7
01.12.12, 4:41 PM
02
5 minute guide
Listening to Surround Sound
This receiver was designed with the easiest possible setup in mind, so with the following quick
setup guide, you should have your system hooked up for surround sound in no time at all. In most
cases, you can simply leave the receiver in the default settings.
1
Hook up your DVD player.
For surround sound, you’ll want to hook up using a digital connection from the DVD player to the
receiver. You can do this with either a coaxial, or an optical connection (you don’t need to do both). If
you hook up using an optical cable, you should refer to Optical digital input setting on page 43 to
assign the optical input to DVD.
Use a video cord to connect the video output on your DVD to the receiver using the jacks shown
below.
2
Hook up your TV.
Use a video cord to connect your receiver to the TV using the jacks as shown below.
Optical cable
Coaxial cable
Note: If you hook up
using a optical cable,
see Optical input
setting on page 43 to
assign the optical
input to DVD.
Video cord
DIGITAL IN
ASSIGNABLE
COAX
OPT
(DVD/LD) ¥
DIGITAL OUT
DVD
/ LD
FRONT
VIDEO OUT
S
IN
DIGITAL IN
AUX
IN
D VIN D
ANTENNA
5.1CH
REC INPUT
CD-R AM IN
/ TAPE LOOP
FM
IN
/ MD UNBAL
75 Ω
¡¢
7
8
(T V / S A T ) ¥
OPT
This receiver*
OPT
R
SURROUND
(CD)
ø
DIGITAL
OUT
Y
OUT
IN
Î
3
VCR /
DVR
MONITOR
OUT
SUB
WOOFER
IN
TV/
IN SAT
IN
DVD /
IN LD
PREOUT
CONTROL
IN
PLAY
AUDIO
ASSIGNABLE
L
DVD player
OUT
PB
VIDEO
S
P
E
A
A
K
E
R
S
R
FRONT
PR
VIDEO IN
Video cord
Y
PB
(T V / SAT) IN ø
CENTER
L
R SURROUND L
MONITOR
OUT
FRONT
L
SUB
WOOFER
* The illustration
shows the VSXD711, but DVD
connections for
the VSX-D811S
are the same.
En
8
R
PREOUT
CENTER
8
XRB3013A.07.12
PR
OUT
PREOUT
TV
( D V D / LD) IN ¥
MONITOR OUT
L
IN
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
R
COMPONENT
VIDEO
( T V / SAT) ¥
MONITOR
OUT
OUT
DVD PLAYER
41
S - VIDEO
VIDEO
TV /
SAT
DVD
/ LD
FRONT
IN
0
(DVD/ LD) ¥
CD
VCR /
DVR
IN
STANDBY/ON
COAX
ASSIGNABLE
DVD 5.1CH INPUT
CENTER SUB W.
01.12.12, 4:41 PM
B
5 minute guide
02
3
Connect your speakers.
A complete setup of speakers is shown here (six speakers (including the subwoofer) for the VSXD711, and eight (also including the subwoofer) for the VSX-D811S), but everyone’s home setup will
vary. Simply connect the speakers you have in the manner shown below. The receiver will work with
just two stereo speakers (the front speakers in the diagram) but using at least three speakers is
recommended, and a complete setup is best.
Make sure you connect the speaker on the right to the right terminal and the speaker on the left to
the left terminal. Also make sure the positive and negative (+/–) terminals on the receiver match
those on the speakers.
• Use speakers with a nominal impedance of 8 Ω to 16 Ω.
• If you’re not using a subwoofer, change the front speaker setting (see Speaker setting on page
39) to large
• When using the speaker on your TV as the center speaker (C), connect the CENTER PREOUT
jack on this unit to the audio input jack on your TV. In this case the center speaker shown is
unnecessary.
Front Speakers
L
R
Surround Speakers
SL
SR
Center Speaker
C
Use speakers with a
nominal impedance
of 8 Ω to 16 Ω.
DIGITAL IN
COAX
OPT
OPT
ASSIGNABLE
ANTENNA
IN
AUX
IN
CD
DVD 5.1CH INPUT
CENTER SUB W.
(DVD/ LD) ¥
S - VIDEO
VCR /
DVR
AM
LOOP
R
SURROUND
(CD)
ø
COMPONENT
VIDEO
( T V / SAT) ¥
DIGITAL
OUT
PB
PR
OUT
VIDEO
TV /
SAT
IN
DVD
/ LD
FRONT
IN
VCR /
DVR
IN
OUT
IN
IN
MONITOR
OUT
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
TV/
IN SAT
SUB
WOOFER
DVD /
IN LD
PREOUT
CONTROL
IN
OUT
PLAY
R
AUDIO
( D V D / LD) IN ¥
L
Y
FM
UNBAL IN
75 ‰
ASSIGNABLE
MONITOR OUT
MONITOR
OUT
L
S
P
E
A
A
K
E
R
S
R
FRONT
L
Y
PB
(T V / SAT) IN ø
CENTER
PR
R SURROUND L
R
FRONT
L
AC OUTLET
PREOUT
CENTER
B
VSX-D711
TV
Be sure to complete all
connections before
connecting this unit to
the AC power source.
INPUT
Powered subwoofer
9
En
XRB3013A.07.12
9
01.12.12, 4:41 PM
02
5 minute guide
Front Speakers
L
R
Surround Speakers
SL
SR
Center Speaker
C
DIGITAL IN
COAX
OPT
Surround back speakers
SBL
SBR
OPT
ASSIGNABLE
ANTENNA
IN
AUX
IN
CD
DVD 7.1CH INPUT
CENTER SUB W.
(DVD/ LD) ¥
S - VIDEO
SURROUND
R
L
VCR /
DVR
AM
LOOP
SURROUND
L BACK
R
FM
UNBAL IN
75 Ω
TV /
SAT
IN
DVD
/ LD
FRONT
IN
IN
VIDEO
OUT
IN
MONITOR
OUT
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
SUB
WOOFER
(CD)
ø
COMPONENT
VIDEO
(TV /
SAT)
MONITOR
OUT
TV/
IN SAT
DVD /
IN LD
CONTROL
R
AUDIO
OUT
L
VSX-D811S
(CD-R/
/ TAPE
/ MD)
ø
DIGITAL
OUT
S
P
E
A
A
K
E
R
S
R
FRONT
PREOUT
ASSIGNABLE ( D V D / LD) IN ¥
L
L
MONITOR OUT
Y
OUT
VCR /
DVR
IN
PREOUT
PLAY
IN
¥
PB
L
PR
CENTER
Y
PB
(T V / SAT) IN ø
PR
R SURROUND BACK L
R
FRONT
SURROUND
BACK
R
SURROUND
CENTER
R SURROUND L
R
FRONT
L
AC OUTLET
B
Subwoofer
(passive)
INPUT
TV
Be sure to complete all
connections before
connecting this unit to
the AC power source.
Powered subwoofer
VSX-D811S only
Surround back
speaker (or
subwoofer)
• If you are using only one surround back
speaker, connect the positive wire to the
right channel (+) terminal, and the
negative wire to the left channel (–)
terminal (shown at right).
• If you select subwoofer (SB SUBWF) in the
Surround back speaker setting (see page
40) you can hook up a subwoofer instead
of speakers to the surround back speaker
terminals. Connect the wires just as above
(and as shown at right), connecting the
positive wire to the right channel (+)
terminal, and the negative wire to the left
channel (–) terminal.
VSX-D811S
R SURROUND BACK L
10
En
XRB3013A.07.12
10
01.12.12, 4:41 PM
5 minute guide
02
4
Plug in the receiver and switch it on, followed by your DVD player, your subwoofer and
the TV.
Make sure you’ve set the video input on your TV to this receiver. Check the manual that came with
the TV if you don’t know how to do this.
Also make sure that DVD/LD is showing in the receiver’s display, indicating that the DVD input is
selected. If it isn’t, press DVD/LD on the remote control to set the receiver to the DVD input.
5
Press QUICK SETUP on the front panel to specify your speaker setup and your room
size.
Use the MULTI JOG/INPUT SELECTOR dial to select and ENTER to confirm your selection. See
Using the Quick Setup on the next page if you’re unsure about the settings.
6
Play a DVD, and adjust the volume to your liking.
There are several other sound options you can select. See pages 32–33 for more on this. See also
Choosing your receiver setup on page 38–43 for more setup options.
Depending on your DVD player or source discs, you may only get digital 2 channel stereo and
analog sound. In this case, the listening mode must be set to Standard (it should already be
set—see page 34 if you need to do this) if you want multi-channel surround sound.
11
En
XRB3013A.07.12
11
01.12.12, 4:41 PM
02
5 minute guide
Using the Quick Setup
You can use the Quick Setup to get your system
up and running with just a few button presses.
The receiver automatically makes the necessary
settings after you have selected your speaker
setup and room size. If you want to make more
specific settings, refer to Choosing your receiver
setup on pages 38–43. Use the front panel
controls for the steps below.
Check the table below to find the speaker
setup that corresponds with your system.
Front Center Surround Surround Sub
Speakers Speaker Speakers Back Sp. Woofer
3.0 ch
3.1 ch
4.0 ch
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
N∫m-Û≥,,
4.1 ch
5.0 ch
INPUT
SELECTOR
MULTI JOG
ENTER
5.1 ch
MASTER VOLUME
ADVANCED
SURROUND
STEREO/
DIRECT
SIGNAL
SELECT
MIDNIGHT/
LOUDNESS
SPEAKERS
MONITOR
TONE
6.0 ch*
QUICK SETUP
UP
DOWN
6.1 ch*
MULTI JOG
LISTENING MODE
VIDEO INPUT
FL DIMMER
DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
7.0 ch*
R
R
7.1 ch*
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
(1 speaker)
(1 speaker)
√
(2 speakers)
(2 speakers)
√
* VSX-D811S only
1
If the receiver is off, press STANDBY/
ON to turn the power on.
The STANDBY indicator goes out.
2
Press QUICK SETUP.
The display prompts you to select your speaker
setup.
3
Use the MULTI JOG/INPUT SELECTOR
dial to choose your speaker setup.
Cycle between the following choices:
3.0ch
3.1ch
4.0ch
7.1ch*
4.1ch
7.0ch*
5.0ch
4
Press ENTER.
The display prompts you to select your room
size.
5
Use the the MULTI JOG/INPUT
SELECTOR dial to choose your room size.
Depending on the distance of your speakers
from the listening position, choose between
Small, Medium, or Large (see table below).
S
12 ft.
Center
10 ft.
Surround
6 ft.
Surround Back* 3 ft.
Front
M
L
12 ft.
10 ft.
7 ft.
5 ft.
12 ft.
10 ft.
9 ft.
7 ft.
* VSX-D811S only
6.1ch*
6.0ch*
* VSX-D811S only
5.1ch
6
Press ENTER to confirm your setup.
The display shows the speaker setup and room
size that you have selected.
12
En
XRB3013A.07.12
12
01.12.12, 4:41 PM
Connecting up
03
Before making or changing any connections, switch off the power and disconnect the power cord from
the AC outlet.
Audio/Video cords
Component video cords
Use audio/video cords (not supplied) to connect
the audio/video components and a video cord
to connect the monitor TV.
Use component video cords to get the best
possible color reproduction of your video
source. The color signal of the TV is divided into
the luminance (Y) signal and the color (PB and
PR) signals and then output. In this way,
interference between the signals is avoided.
Connect from the component video jacks on the
rear of the receiver to the component video
jacks on the video component you are hooking
up.
Connect red plugs to R (right), white plugs to L
(left), and the yellow plugs to VIDEO.
Be sure to insert completely.
R
L
VID
EO
Y
PB
Green
S-video cables
Use S-video cables (not supplied) to get clearer
picture reproduction than regular video cords.
Connect from an S-video jack on the rear of the
receiver to an S-video jack on the video
component you are hooking up.
Be sure to insert completely.
SV
IDE
O
PR
Blue
Red
Digital audio coaxial cords/
Optical cables
Commercially available digital audio coaxial
cords (standard video cords can also be used)
or optical cables (not supplied) are used to
connect digital components to this receiver.
Be sure to insert completely.
Digital audio coaxial cord
(or standard video cord)
Optical cable
13
En
XRB3013A.13.25
13
01.12.12, 4:42 PM
03
Connecting up
Connecting digital components
The easiest way to hook up this receiver for surround sound is to use a digital input. You can do this
by either coaxial or optical connections (you do not need to do both). The quality of these two types
of connections is the same but since some digital components only have one type of digital
terminal, it is a matter of matching like with like (for example, the coaxial output from the
component to coaxial input on the receiver). The VSX-D711 has three digital inputs on the rear panel
(two coaxial inputs and a optical input) and the VSX-D811S has four (two coaxial inputs and two
optical inputs). Connect your digital components to the rear panel as shown below. See page 18 to
connect the front panel optical input on the VSX-D811S.
There is one digital output jack which is marked DIGITAL OUT. If you connect this to the optical
input on a digital recorder (currently these include MD, DAT and CD-R) you can make direct digital
recordings with this unit.
When connecting your equipment, always make sure the power is turned off and the power cord is
disconnected from the AC outlet.
The arrows indicate the direction of the audio signal.
VSX-D711
DIGITAL IN
COAX
OPT
DIGITAL
IN
OPT
CD recorder
ASSIGNABLE
ANTENNA
DVD 5.1CH INPUT
CENTER SUB W.
AUX
IN
(DVD/ LD) ¥
CD
IN
AM
LOOP
(CD)
S - VIDEO
VCR /
DVR
R
SURROUND
ø
COMPONENT
VIDEO
( T V / SAT) ¥
DIGITAL
OUT
MONITOR OUT
MONITOR
OUT
L
Y
FM
UNBAL IN
75 ‰
ASSIGNABLE
PB
PR
OUT
VIDEO
TV /
SAT
IN
DVD
/ LD
FRONT
IN
VCR /
DVR
IN
OUT
IN
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
MONITOR
OUT
SUB
WOOFER
IN
TV/
IN SAT
DVD /
IN LD
PREOUT
CONTROL
IN
PLAY
R
AUDIO
OUT
L
S
P
E
A
A
K
E
R
S
R
FRONT
L
Y
PB
(T V / SAT) IN ø
CENTER
PR
R SURROUND L
R
DIGITAL
OUTL
Satellite
tuner
FRONT
AC OUTLET
PREOUT
CENTER
B
DIGITAL OUT
COAX
CD player
DIGITAL OUT
COAX
DVD player
14
En
XRB3013A.13.25
14
01.12.12, 4:42 PM
Connecting up
03
Satellite
tuner
DIGITAL
OUT
DIGITAL
CD recorder
DIGITAL
IN
OUT
VSX-D811S
DIGITAL IN
COAX
OPT
OPT
ASSIGNABLE
ANTENNA
IN
AUX
IN
CD
DVD 7.1CH INPUT
CENTER SUB W.
(DVD/ LD) ¥
S - VIDEO
SURROUND
R
L
VCR /
DVR
AM
LOOP
SURROUND
L BACK
R
FM
UNBAL IN
75 Ω
TV /
SAT
IN
DVD
/ LD
FRONT
IN
IN
VIDEO
OUT
IN
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
MONITOR
OUT
SUB
WOOFER
(CD)
ø
COMPONENT
VIDEO
(TV /
SAT)
R
AUDIO
L
(CD-R/
/ TAPE
/ MD)
ø
DIGITAL
OUT
TV/
IN SAT
DVD /
IN LD
PREOUT
OUT
S
P
E
A
A
K
E
R
S
R
FRONT
ASSIGNABLE
PREOUT
IN ¥
( D V D / LD) IN
L
L
MONITOR OUT
Y
OUT
VCR /
DVR
IN
CONTROL
PLAY
IN
¥
MONITOR
OUT
PB
L
PR
CENTER
Y
P BB
(T V / SAT) IN ø
P RR
R SURROUND BACK L
R
FRONT
FRONT
R
SURROUND
SURROUND
SURROUND
SURROUND
BACK
BACK
CD player
CENTER
DIGITAL
OUT
CENTER
R SURROUND L
COAX
R
FRONT
L
AC OUTLET
B
DIGITAL OUT
COAX
DVD player
If you have an LD player, you need to make special connections to ensure you can play 2 RF
format LDs on your system. If this is the case, hook up your DVD or LD player directly to an RF
demodulator using both the 2 RF output and either a coaxial or optical digital connection. We
also recommend hooking up your digital components to analog audio jacks as well. Make sure
the RF demodulator digital in switch is set correctly (optical or coaxial depending on the
connection). See the component's instruction manual if you are unsure about its input and
output jacks.
15
En
XRB3013A.13.25
15
01.12.12, 4:42 PM
03
Connecting up
Connecting audio components
To begin set up, connect your analog audio components (such as a cassette deck) to the jacks. For
components you want to record with, you need to hook up four plugs to the receiver (a set of stereo
inputs and a set of stereo outputs), but for components that only play, you only need to hook up one
set of stereo plugs. You must also hook up your digital components to analog audio jacks if you want
to record to/from digital components (like an MD) to/from analog components. See page 14 for
more on digital connections.
When connecting your equipment, always make sure the power is turned off and the power cord is
disconnected from the AC outlet.
The arrows indicate the direction of the audio signal.
OUTPUT
DIGIT
L
R
CD player
ASSI
ANTENNA
IN
AUX
IN
CD
VCR /
DVR
AM
LOOP
FM
UNBAL IN
75 ‰
TV /
SAT
IN
DVD
/ LD
FRONT
IN
SURROUND
L
IN
OUT
IN
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
R
IN
CD-R/Tape/MD Deck
R
VIDEO
REC PLAY
L
DVD 5.1CH INPUT
CENTER SUB W.
MONI
OUT
SUB
WOOF
PREOU
PLAY
R
AUDIO
L
16
En
XRB3013A.13.25
16
01.12.12, 4:42 PM
Connecting up
03
Connecting DVD 5.1 channel components
If you prefer to use a seperate component for decoding DVDs, you can connect a decoder or a DVD
player with multi-channel analog outputs to the multi-channel inputs of this receiver.
When connecting your equipment, always make sure the power is turned off and the power cord is
disconnected from the AC outlet.
The arrows indicate the direction of the signal.
DVD/multi-channel decoder with
5.1 channel analog output jacks
VSX-D711
DIGITAL IN
COAX
OPT
OPT
ASSIGNABLE
ANTENNA
IN
AUX
IN
CD
DVD 5.1CH INPUT
CENTER SUB W.
(DVD/ LD) ¥
S - VIDEO
VCR /
DVR
AM
LOOP
R
SURROUND
(CD)
ø
COMPONENT
VIDEO
( T V / SAT) ¥
DIGITAL
OUT
PB
PR
Y
OUT
VIDEO
TV /
SAT
IN
DVD
/ LD
FRONT
IN
VCR /
DVR
IN
OUT
IN
S
P
E
A
A
K
E
R
S
IN
MONITOR
OUT
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
TV/
IN SAT
SUB
WOOFER
DVD /
IN LD
PREOUT
CONTROL
IN
OUT
PLAY
R
AUDIO
( D V D / LD) IN ¥
L
Y
FM
UNBAL IN
75 ‰
ASSIGNABLE
MONITOR OUT
MONITOR
OUT
L
DIGITAL IN
COAX
R
FRONT
PB
(T V / SAT) IN ø
CENTER
L
PR
SUB
WOOFER
OUTPUT
R SURROUND L
SURROUND
OUTPUT
R
FRONT
R
L
VIDEO
OUTPUT
AC OUTLET
R
B
PREOUT
CENTER
OPT
FRONT
OUTPUT
CENTER
OUTPUT
L
L
OPT
ASSIGNABLE
ANTENNA
DVD 7.1CH INPUT
CENTER SUB W.
AUX
IN
(DVD/ LD) ¥
CD
IN
S - VIDEO
SURROUND
R
L
VCR /
DVR
AM
LOOP
SURROUND
L BACK
R
FM
UNBAL IN
75 Ω
TV /
SAT
IN
DVD
/ LD
FRONT
IN
IN
VIDEO
OUT
IN
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
MONITOR
OUT
SUB
WOOFER
(CD)
ø
COMPONENT
VIDEO
(TV /
SAT)
MONITOR
OUT
PLAY
R
AUDIO
L
(CD-R/
/ TAPE
/ MD)
ø
DIGITAL
OUT
TV/
IN SAT
DVD /
IN LD
PREOUT
OUT
S
P
E
A
A
K
E
R
S
R
FRONT
PREOUT
ASSIGNABLE ( D V D / LD) IN ¥
L
SURROUND
BACK
L
MONITOR OUT
Y
OUT
VCR /
DVR
IN
CONTROL
IN
¥
PB
L
PR
CENTER
Y
PB
(T V / SAT) IN ø
PR
R SURROUND BACK L
R
R
SURROUND CENTER SURROUND
FRONT
OUTPUT
OUTPUT
SURROUND
FRONT
FRONT
R
L
R
L
L
R
R
L
SURROUND
BACK OUTPUT
L
SUB
WOOFER
OUTPUT
CENTER
OUTPUT
VIDEO
OUTPUT
AC OUTLET
B
R
VSX-D811S
DVD/multi-channel decoder with
7.1 channel analog output jacks
• The multi-channel input can only be used when DVD 5.1 CH (or DVD 7.1 CH) is selected (see
page 37).
• If the component you are connecting (to the VSX-D811S) only has one surround back channel
output, change the Surround back channel input setting (page 43) to SB 1ch IN.
17
En
XRB3013A.13.25
17
01.12.12, 4:42 PM
03
Connecting up
Connecting video components
Connect your video components to the jacks as shown below. With digital video components (like a
DVD player), you must use the connections shown on this page for the video signal, but in order to
hear a digital source (like a DVD) you should hook up the audio to a digital input (see page 14). It is
also a good idea to hook up your digital components with analog audio connections (see page 16).
For better quality video, you can hook up using the component video jacks or the S-video jacks
(quality descends in this order) on the rear of the receiver instead of the regular video jacks. Make
sure they are connected to the video component using the same kind of connection.
When connecting your equipment, always make sure the power is turned off and the power cord is
disconnected from the AC outlet.
The arrows indicate the direction of the signal.
Video deck
INPUT
OUTPUT
DIGITAL IN
VIDEO
COAX
OPT
OUTPUT
VIDEO
VIDEO
L
L
OPT
ASSIGNABLE
L
ANTENNA
DVD 5.1CH INPUT
CENTER SUB W.
AUX
IN
(DVD/ LD) ¥
CD
IN
S - VIDEO
R
TV tuner (or
Satellite tuner)
VCR /
DVR
AM
LOOP
R
SURROUND
ø
( T V / SAT) ¥
DIGITAL
OUT
ASSIGNABLE
R
R
L
PB
PR
Y
OUT
VIDEO
TV /
SAT
IN
DVD
/ LD
FRONT
IN
VCR /
DVR
IN
OUT
IN
IN
MONITOR
OUT
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
OUTPUT
TV/
IN SAT
SUB
WOOFER
DVD /
IN LD
PREOUT
CONTROL
IN
OUT
PLAY
R
AUDIO
( D V D / LD) IN ¥
MONITOR OUT
MONITOR
OUT
Y
FM
UNBAL IN
75 ‰
VIDEO
(CD)
COMPONENT
VIDEO
L
R
S
P
E
A
A
K
E
R
S
FRONT
L
PB
(T V / SAT) IN ø
CENTER
PR
R SURROUND L
INPUT
R
FRON
PREOUT
CENTER
VIDEO
L
DVD or LD player
R
TV (monitor)
Connecting to the front panel
video terminal
Front video connections are accessed via the
front panel input selector as VIDEO. There are
standard audio/video jacks as well as an
S-video jack (the VSX-D811S also has an optical
input jack). Hook them up the same way you
made the rear panel connections.
REO/
ECT
SIGNAL
SELECT
MIDNIGHT/
LOUDNESS
SPEAKERS
MONITOR
TONE
QUICK SETUP
MULTI JOG
VIDEO INPUT
DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
R
Video
camera
(etc.)
VIDEO INPUT
DIGITAL OUT
V
L
R
18
En
XRB3013A.13.25
18
01.12.12, 4:42 PM
Connecting up
03
Connecting antennas
Antenna snap connectors
Connect the AM loop antenna and the FM wire
antenna as shown below. To improve reception
and sound quality, connect external antennas
(see Using external antennas below). Always
make sure that the receiver is switched off and
unplugged from the wall outlet before making
or changing any connections.
Twist the exposed wire strands together and
insert into the hole, then snap the connector
shut.
3/8 in. (10mm)
Using external antennas
AM LOOP
ANTENNA
To improve FM reception
Connect an external FM antenna.
FM
UNBAL
75Ω
FM WIRE
ANTENNA
75 Ω coaxial cable
FM wire antenna
Connect the FM wire antenna and fully extend
vertically along a window frame or other
suitable area, etc.
AM loop antenna
Assemble the antenna and connect to the
receiver. Attach to a wall, etc. (if desired) and
face in the direction that gives the best
reception.
FM
ANTENNA
To improve AM reception
Connect a 15-18 feet length of vinyl-coated wire
to the AM antenna terminal without disconnecting the supplied AM loop antenna.
For the best possible reception, suspend
horizontally outdoors.
Outdoor antenna
Indoor
antenna
(Vinylcoated
wire)
15-18 ft. (5–6m)
AM LOOP
ANTENNA
19
En
XRB3013A.13.25
19
01.12.12, 4:42 PM
03
Connecting up
Connecting the speakers (VSX-D711)
A complete setup of six speakers (including the subwoofer) is shown below, but everyone’s home
setup will vary. Simply connect the speakers you have in the manner shown below. The receiver will
work with just two stereo speakers (the front speakers in the diagram) but using at least three
speakers is recommended, and a complete setup is best. If you’re not using a subwoofer, change
the front speaker setting (see Speaker setting on page 39) to large.
Make sure you connect the speaker on the right to the right terminal and the speaker on the left to
the left terminal. Also make sure the positive and negative (+/–) terminals on the receiver match
those on the speakers.
Front Speakers
L
R
Surround Speakers
SL
SR
Center Speaker
C
Use speakers with a
nominal impedance
of 8 Ω to 16 Ω.
DIGITAL IN
COAX
OPT
OPT
ASSIGNABLE
ANTENNA
IN
AUX
IN
CD
DVD 5.1CH INPUT
CENTER SUB W.
(DVD/ LD) ¥
S - VIDEO
VCR /
DVR
AM
LOOP
R
SURROUND
(CD)
ø
COMPONENT
VIDEO
( T V / SAT) ¥
DIGITAL
OUT
PB
PR
OUT
VIDEO
TV /
SAT
IN
DVD
/ LD
FRONT
IN
VCR /
DVR
IN
OUT
IN
IN
MONITOR
OUT
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
TV/
IN SAT
SUB
WOOFER
DVD /
IN LD
PREOUT
CONTROL
IN
OUT
PLAY
R
AUDIO
( D V D / LD) IN ¥
L
Y
FM
UNBAL IN
75 ‰
ASSIGNABLE
MONITOR OUT
MONITOR
OUT
L
S
P
E
A
A
K
E
R
S
R
FRONT
L
Y
PB
(T V / SAT) IN ø
CENTER
PR
R SURROUND L
R
FRONT
L
AC OUTLET
PREOUT
CENTER
B
VSX-D711
TV
Be sure to complete all
connections before
connecting this unit to
the AC power source.
INPUT
Powered subwoofer
When using the speaker on your TV as the center speaker
(C), connect the CENTER PREOUT jack on this unit to the
audio input jack on your TV. In this case the center speaker
shown is unnecessary.
20
En
XRB3013A.13.25
20
01.12.12, 4:42 PM
Connecting up
03
Connecting the speakers (VSX-D811S)
A complete setup of eight speakers (including the subwoofer) is shown below, but everyone’s home
setup will vary. Simply connect the speakers you have in the manner shown below. The receiver will
work with just two stereo speakers (the front speakers in the diagram) but using at least three
speakers is recommended, and a complete setup is best for surround sound. If you’re not using a
subwoofer, change the front speaker setting (see Speaker setting on page 39) to large.
Make sure you connect the speaker on the right to the right terminal and the speaker on the left to
the left terminal. Also make sure the positive and negative (+/–) terminals on the receiver match
those on the speakers.
Use speakers with a nominal impedance of 8 Ω to 16 Ω.
Front Speakers
L
R
Surround Speakers
SL
SR
Center Speaker
C
DIGITAL IN
COAX
OPT
Surround Back Speakers
SBL
SBR
OPT
ASSIGNABLE
ANTENNA
IN
AUX
IN
CD
DVD 7.1CH INPUT
CENTER SUB W.
(DVD/ LD) ¥
S - VIDEO
SURROUND
R
L
VCR /
DVR
AM
LOOP
SURROUND
L BACK
R
FM
UNBAL IN
75 Ω
TV /
SAT
IN
DVD
/ LD
FRONT
IN
IN
VIDEO
OUT
IN
MONITOR
OUT
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
SUB
WOOFER
(CD)
ø
COMPONENT
VIDEO
(TV /
SAT)
MONITOR
OUT
TV/
IN SAT
DVD /
IN LD
CONTROL
R
AUDIO
OUT
L
VSX-D811S
(CD-R/
/ TAPE
/ MD)
ø
DIGITAL
OUT
S
P
E
A
A
K
E
R
S
R
FRONT
PREOUT
ASSIGNABLE ( D V D / LD) IN ¥
L
SURROUND
BACK
L
MONITOR OUT
Y
OUT
VCR /
DVR
IN
PREOUT
PLAY
IN
¥
PB
L
PR
CENTER
Y
PB
(T V / SAT) IN ø
PR
R SURROUND BACK L
R
FRONT
R
SURROUND
CENTER
R SURROUND L
R
FRONT
L
AC OUTLET
B
Subwoofer
(passive)
TV
INPUT
Be sure to complete
all connections
before connecting
this unit to the AC
power source.
Powered subwoofer
21
En
XRB3013A.13.25
21
01.12.12, 4:42 PM
03
Connecting up
• When using the speaker on your TV as the center speaker (C), connect the CENTER PREOUT
jack on this unit to the audio input jack on your TV. In this case the center speaker shown is
unnecessary.
• If you are using only one surround back speaker, connect the positive wire to the right channel
(+) terminal, and the negative wire to the left channel (–) terminal (see illustration on page 11).
• If you select subwoofer (SB SUBWF) in the Surround back speaker setting (see page 39) you can
hook up a subwoofer instead of speakers to the surround back speaker terminals. Connect the
positive wire to the right channel (+) terminal, and the negative wire to the left channel (–)
terminal (see illustration on page 11).
Speaker terminals
3/8 in. (10mm)
1
Twist exposed wire strands together.
2
Loosen speaker terminal and insert exposed wire.
3
Tighten terminal.
The speaker terminals also
accept single banana
plugs. (Refer to speaker
manual for details.)
Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker
terminal. If any of the bare speaker wire touches the back panel it may cause the power to cut off as
a safety measure. Use good quality speaker wire to connect the speakers to the receiver.
A and B speaker systems
The receiver has two speaker systems: A and B. A is the main system supporting the full speaker
setup. If you switch on both A and B speaker systems, only the front speakers and the subwoofer
will be audible. No sound will come from the center, surround, or surround back speakers, but
multi-channel sources will be down-mixed to the active speakers so no sound will be lost. Similarly,
if you choose just the B system you‘ll only hear the front speakers connected to the B system and
multi channel sources will be down-mixed to these two speakers.
Hints on speaker placement
Speakers are usually designed with a particular placement in mind. Some are designed to be
floorstanding, while others should be placed on stands to sound their best. Some should be placed
near a wall; others should be placed away from walls. We have provided a few tips on getting the
best sound from your speakers (below), but you should also follow the guidelines on placement that
the speaker manufacturer provided with your particular speakers to get the most out of them.
• Place the front left and right speakers at equal distances from the TV.
22
• When placing speakers near the TV, we recommend using magnetically shielded speakers to
prevent possible interference, such as discoloration of the picture when the TV is switched on. If
you do not have magnetically shielded speakers and notice discoloration of the TV picture, move
the speakers farther away from the TV.
En
XRB3013A.13.25
22
01.12.12, 4:43 PM
Connecting up
03
• Place the center speaker above or below the
TV so that the sound of the center channel is
localized at the TV screen.
If you choose to install the center speaker
on top of the TV, be sure to secure it with
putty, or by other suitable means, to
reduce the risk of damage or injury
resulting from the speaker falling from
the TV in the event of external shocks
such as earthquakes.
• If possible, place the surround speakers
slightly above ear level.
3-D view of speaker set up (VSX-D711)
Overhead view of speaker set up
(VSX-D811S)
Front
Left
Front
Right
Center
• Try not to place the surround speakers
further away from the listening position than
the front and center speakers. Doing so can
weaken the surround sound effect.
• To achieve the best possible surround
sound, install your speakers as shown
below. Be sure all speakers are installed
securely to prevent accidents and improve
sound quality.
Overhead view of speaker set up (VSX-D711)
Front
Left
Center
Subwoofer
Surround
Left
Surround
Right
Listening Position
Surround Back
Left
Surround Back
Right
Front
Right
3-D view of speaker set up (VSX-D811S)
Subwoofer
Surround
Left
Surround
Right
Listening Position
23
En
XRB3013A.13.25
23
01.12.12, 4:43 PM
03
Connecting up
Connecting additional amplifiers
(VSX-D811S only)
This receiver has more than sufficient power for any home use, however it is possible to add
additional amplifiers to every channel. Make the connections shown below to add amplifiers to
power your speakers. Always make sure that the receiver is switched off and unplugged from the
wall outlet before making or changing any connections.
The arrows indicate the direction of the audio signal.
ANALOG IN
L
VSX-D811S
ANALOG IN
OPT
DIGITAL IN
OPT
ASSIGNABLE
ANTENNA
DVD 7.1CH INPUT
CENTER SUB W.
AUX
IN
(TV /
SAT)
IN
¥
(CD-R/ ø
/ TAPECD
/ MD)
1
DIGITAL OUT
2
RY
FM
UNBAL IN
75
IN
IN
IN
R
L
L
SURROUND
BACK
L
Surround channel
amplifier
R
S - VIDEO
MONITORSURROUND
OUT
R
L
VCR /
DVR
AM
LOOP
PREOUT
ASSIGNABLE
( D V D / LD) IN ¥
COMPONENT
(DVD/ LD) ¥
VIDEO
Front channel
amplifier
R
IN
R FRONT
S
TV /
SAT
P
IN
DVD
E
/ LD
FRONT
A
DVD
A
5.1CH
K
REC INPUT
IN
CD-R
E
/ TAPE
/ MD
R
S L PLAY
PB
LVIDEO
SURROUND
PLR BACK Y
CENTER
PB
(T V / SAT) IN ø
PR
R SURROUND BACK L
R
FRONT
R
SURROUND
CENTER
R SURROUND L
R
FRONT
ANALOG IN
Surround back
channel amplifier
ANALOG IN
Center channel
amplifier
L
OUT
AC OUTLET
MONITOR
OUT
B
SUB
WOOFER
PREOUT
AUDIO
INPUT
Powered
subwoofer
• To hear sound only from the pre-outs, disconnect any speakers that are connected directly to
the receiver.
• If you’re not using a subwoofer, change the front speaker setting (see Speaker setting on page
39) to large.
24
En
XRB3013A.13.25
24
01.12.12, 4:43 PM
Connecting up
03
AC outlet
[switched 100 W (0.8 A) max]
Power supplied through this outlet is turned on and off by the
receiver's POWER switch. Total electrical power consumption of
connected equipment should not exceed 100 W (0.8 A).
AC OUTLET
SWITCHED
100 W MAX
0.8 A MAX
DO NOT CONNECT A MONITOR, TV SET, HEATER, OR SIMILAR
APPLIANCE TO THIS UNIT'S AC OUTLET.
Do not connect appliances with high power consumption to the
AC OUTLET in order to avoid overheating and fire risk. This can
also cause the receiver to malfunction.
• Make sure no exposed speaker wire is touching the rear panel, this may cause the receiver to
turn off automatically.
• This unit should be disconnected by removing the power plug from the wall socket when not in
regular use (ex. when on vacation).
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the
power cord when your hands are wet as this could cause a short circuit or an electric shock. Do not
place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in
the cord or tie it with other cords. The power cords should be routed such that they are not likely to
be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the
power cord once in a while. When you find it damaged, ask your nearest Pioneer authorized service
center or your dealer for a replacement.
Operating other Pioneer
components
By connecting a control cord (optional),
you can point the remote controls of other
Pioneer components at the receiver’s
remote sensor. The remote control signals
are received by the remote sensor of this
unit, and sent to the other devices via the
CONTROL OUT terminal.
CONTROL
IN
OUT CONTROL
OUT
Receiver
Other Pioneer products
with Î mark
Remote
control unit
Connect to CONTROL
IN terminal of other
Pioneer products
with Î mark.
25
En
XRB3013A.13.25
25
01.12.12, 4:43 PM
04
Controls and Displays
Front panel
1
3
2
4
5
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
N∫m-Û≥,,
INPUT
SELECTOR
MULTI JOG
ENTER
STANDBY
STANDBY/ON
MASTER VOLUME
UP
DOWN
PHONES
R
7
6
8
9
STATION
TUNING
10
STANDARD
ADVANCED
SURROUND
11 12 13 14 15 16
STEREO/
DIRECT
SIGNAL
SELECT
MIDNIGHT/
LOUDNESS
SPEAKERS
MONITOR
TONE
QUICK SETUP
MULTI JOG
LISTENING MODE
VIDEO INPUT
TUNER EDIT
CLASS
BAND
MPX
INPUT ATT
FL DIMMER
MULTI JOG
DIGITAL IN
S-VIDEO
24 23 22 21 20 19
18
VIDEO
L
AUDIO
R
17
1
STANDBY/ON
Switches the receiver between on and standby.
8
STATION (+/–) buttons (pages 46–47)
Selects station presets when using the tuner.
2
STANDBY indicator
Lights when the receiver is in standby.
9
TUNING buttons (page 45)
Selects the frequency when using the tuner.
3
Remote sensor
Receives the signals from the remote control.
10
4
ENTER
5
MULTI JOG/INPUT SELECTOR dial
The MULTI JOG/INPUT SELECTOR dial
performs a number of tasks. Use it to select
options after pressing TONE CONTROL, QUICK
SETUP or TUNER EDIT.
6
MASTER VOLUME
7
PHONES jack
Use to connect headphones. When the
headphones are connected, there is no sound
output from the speakers.
LISTENING MODE buttons
STANDARD (pages 32, 34)
Press for Standard decoding and to switch
between the various Pro Logic II options.
ADVANCED SURROUND (pages 33, 35)
Use to switch between the various
surround modes.
STEREO/DIRECT (pages 32, 35)
Switches direct playback on or off. Direct
playback bypasses the tone controls and
channel levels for the most accurate
reproduction of a source.
26
En
XRB3013A.26.31
26
01.12.12, 4:43 PM
Controls and Displays
04
18
11 SIGNAL SELECT (pages 34, 37, 48)
Use to select an input signal.
19 FL DIMMER
Use this button to make the fluorescent display
(FL) dimmer or brighter.
12 MIDNIGHT/LOUDNESS (page 36)
Use Midnight when listening to movie soundtracks at low volume. Use Loudness to boost
the bass and treble at low volume.
20 INPUT ATT
Use to attenuate (lower) the level of an analog
input signal to prevent distortion.
13 SPEAKERS
Use to cycle through the speaker
system: A = B = A+B
21 MPX (page 45)
Press to receive a radio broadcast in mono.
14 MONITOR
Press to switch tape monitoring on/off.
22 BAND (page 45)
Switches between AM and FM radio bands.
15 TONE
Press this button to access the bass and treble
controls, which you can then adjust with the
MULTI JOG/INPUT SELECTOR dial.
16
QUICK SETUP
17
VIDEO INPUT (page 18)
DIGITAL IN (VSX-D811S only) (page 18)
23 CLASS (pages 46–47)
Switches between the three banks (classes) of
station presets.
24 TUNER EDIT (pages 46–47)
Press to memorize and name a station for recall
using the STATION +/– buttons.
Display
1
2
3
10 11
1
SIGNAL SELECT indicators
Lights to indicate the type of input signal
assigned for the current component:
AUTO
Lights when AUTO signal select is on
4
12
5
6
13
7
8
9
14
15
SB (VSX-D811S only)
Depending on the source, this lights when
a signal with surround back channel
encoding is detected.
DIGITAL
Lights when a digital audio signal is
detected.
27
En
XRB3013A.26.31
27
01.12.12, 4:43 PM
04
Controls and Displays
2 DIGITAL
Lights when a Dolby Digital signal is
detected.
ANALOG
Lights when an analog signal is detected.
DTS
Lights when a source with DTS audio
signals is detected.
2
DTS
When the Standard mode of the receiver is on,
this lights to indicate decoding of a DTS signal.
3
2 DIGITAL
When the Standard mode of the receiver is on,
this lights to indicate decoding of a Dolby
Digital signal.
4
2 PRO LOGIC II
When the Standard mode of the receiver is on,
this lights to indicate Pro Logic II decoding.
5
ATT
Lights when INPUT ATT is used to attenuate
(reduce) the level of the analog input signal.
6
DIRECT
Lights when source direct playback is in use.
This function bypasses all tone, balance,
Advanced surround, and Dolby Surround
effects.
10
Character display
11 Neo:6 (VSX-D811S)
Lights during NEO:6 processing
12 ADV. SURR (Advanced Surround)
Lights when one of the Advanced Surround
modes has been selected.
13 LOUDNESS
Lights when LOUDNESS has been selected.
14
TUNER indicators
STEREO:
Lights when a stereo FM broadcast is being
received in auto stereo mode.
MONO:
Lights when the mono mode is set using the
MPX button.
TUNED:
Lights when a broadcast is being received.
15 Master volume level
Shows the overall volume level. ---dB indicates
the minimum level, and −0 dB indicates the
maximum level.
Depending on your level settings for each
channel, the maximum level can range between
–10 dB and –0 dB.
7
MIDNIGHT
Lights during Midnight listening.
8
MONITOR
Lights when MONITOR is selected (page 48).
9
Speaker indicator
Shows the speaker system currently in use.
28
En
XRB3013A.26.31
28
01.12.12, 4:43 PM
Controls and Displays
04
Remote control
4
DVD
TV
VCR
CD-R
TUN
CD
TVC
1
2
3
TEST TONE
INPUT ATT
FL DIMMER
4
5
6
CH SELECT
LEVEL
8
7
9
EFFECT
0
DTV INFO
6
7
8
DISPLAY/DISC (ENTER)
The button’s use depends on the
component selected. It can be used to
switch the display between the station
preset name and the frequency for the
tuner, enter commands for TV or DTV, and
can also be used to select a disc in a multiCD player.
MULTI CONTROL
RCV
+10
5
10
11
RECEIVER
SOURCE
1
2
3
MPX/RETURN
DISPLAY
DISC
ENTER
D.ACCESS
T.EDIT/GUIDE
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
¡
4
¢
1
TOP MENU
REMOTE SETUP
INPUT SEL.
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
RECEIVER CONTROL
TUNE
S ETU P
ST
ST
12
ENTER
TUNE
13
CHANNEL
MENU
TV VOL
TV INPUT
9
4
Number buttons/Receiver controls/
ENTER
Use the number buttons to directly select a
radio frequency (page 45) or the tracks on a CD,
DVD, etc.
MASTER VOLUME
14
TV
15
TV CONTROL
AV PRE-PROGRAMMED
REMOTE CONTROL UNIT
Receiver Controls
Press the RCV button first to access the
functions above the number buttons. The
display flashes when it isn’t possible to use
a function.
TEST TONE (page 44)
Sounds the test tone when setting up the
surround sound of the receiver.
INPUT ATT
Attenuates (lowers) the level of an analog
input signal to prevent distortion (when the
overload indicator lights).
FL DIMMER
Dims or brightens the display.
1
SOURCE
Press to turn on/off other components connected to the receiver.
CH SELECT (page 44)
Selects a speaker when setting up the
surround sound of the receiver.
2
MULTI CONTROL buttons
Press to select control of other components
(see Controlling the Rest of Your System on
pages 49–52).
LEVEL +/– (page 44)
Adjusts the levels of the surround sound of
the receiver.
3
RCV
Switches the remote to controls the receiver
(used to select the features above the number
buttons. (ex. INPUT ATT, FL. DIMMER). Also
use this button to set up surround sound
(pages 38, 44).
EFFECT +/– buttons (page 35)
Adds or subtracts the amount of effect
with different advanced listening modes
(except 5 or 6 Ch Stereo and Virtual SB).
29
En
XRB3013A.26.31
29
01.12.12, 4:43 PM
04
Controls and Displays
5
Component/Tuner controls
The main buttons (3, 7, etc.) are used to
control a component after you have selected it
using the MULTI CONTROL buttons. The tuner/
DTV controls above these buttons can be
accessed after you have selected the corresponding MULTI CONTROL button (TUNER or
DVD (when connected to DTV)).
6
DVD controls (Press DVD first to access)
These controls will also function as DTV
controls, depending on the component you’ve
selected.
TOP MENU
Displays the disc ‘top’ menu of a DVD.
AUDIO
Changes the audio language or channel.
DTV INFO
Use to bring up information screens on a
digital TV.
MPX/RETURN (page 45)
Switches between stereo and mono
reception of FM broadcasts. If the signal is
weak then switching to mono will improve
the sound quality. Also acts as a stop
button for CDs, tapes, or DVDs.
D. ACCESS (page 49)
After pressing, you can access a radio
station directly using the number buttons.
T. EDIT/GUIDE (page 46–47)
Press to memorize and name a station for
recall using the STATION +/– buttons.
Also displays the guides on a digital TV.
BAND (page 45)
Switches between the tuner AM and FM
bands.
CLASS (page 46–47)
Switches between the three banks
(classes) of radio station presets.
DTV ON/OFF
Switches a digital TV on/off.
DTV MENU
Displays menus on a digital TV.
SUBTITLE
Displays/changes the subtitles included in
multilingual DVD-Video discs.
ANGLE
Switches camera angles on discs with
multi-angle scenes.
7
REMOTE SETUP (pages 49–52)
Press this button to set up the remote control to
control other components.
8
RECEIVER CONTROL buttons
STANDARD (pages 32, 34)
Press to switch between the various Dolby/
DTS modes
ADV. SURR. (pages 33, 35)
Use to switch between the various
surround modes.
STEREO (pages 32, 35)
Switches direct playback on or off. Direct
playback bypasses the tone controls and
channel levels for the most accurate
reproduction of a source.
INPUT SELECT
Use to select the input source.
SIGNAL SELECT (pages 34, 37, 48)
Use to select between an input signal.
30
En
XRB3013A.26.31
30
01.12.12, 4:43 PM
Controls and Displays
04
MIDNIGHT/LOUDNESS (page 36)
Switches to Midnight or Loudness
listening.
MUTE
Mutes the sound (or restores the sound if
it has been muted).
9
TV control buttons
These buttons can only be used to control your
TV.
TV VOLUME +/–
Use to adjust the volume on your TV.
TV INPUT
Use select the TV function.
TV
Use to turn on/off the power of the TV.
10 LED DISPLAY
This display flashes when a command is sent
from the remote control.
11 RECEIVER
This switches between standby and on for this
receiver.
12 }]‘’ (TUNE/ST +/–) /ENTER
Use the arrow buttons when setting up your
surround sound system (see pages 38–43). Also
used to control DVD menus/options and for
deck 1 of a double cassette deck player. Use the
TUNE +/– buttons to find radio frequencies and
use ST +/– to find preset stations (page 45–47).
13 CHANNEL +/–
Select radio station presets. Also skip tracks
backward or forward on CDs, DVDs, etc.
14 MASTER VOLUME +/–
Use to set the listening volume.
15 MENU button
Displays the disc menu of DVD-Video discs. It
also displays TV and DTV menus.
31
En
XRB3013A.26.31
31
01.12.12, 4:43 PM
05
Playing sources
Introduction to Sound Modes
There are three basic sound options: Stereo/
Direct, Standard or Advanced Surround.
Choose one of the following to add depth to a 2
channel source:
Pro Logic
Stereo/Direct
When you select STEREO or DIRECT, you will
hear the source through just the front left and
right speakers (and possibly your subwoofer
depending on your speaker settings). Dolby
Digital and DTS multichannel sources are
downmixed to stereo.
In STEREO, you’ll hear the audio with your
surround settings and you can still use the
Midnight, Loudness, and Tone control functions.
With DIRECT, you will bypass all effects and
surround settings so that the audio remains as
close to the source audio signal as possible.
If you switch on Midnight listening, Loudness, or the Tone controls when DIRECT is
selected, the receiver automatically
switches to STEREO.
This mode gives 4.1 channel surround sound. It
is less sensitive to the quality of the source
material, so may be useful when Pro Logic II
Movie/ Music modes don’t give good results.
Pro Logic II Movie
This mode gives 5.1 channel surround sound. It
is suitable for movies, especially those recorded
in Dolby Surround. The channel separation and
movement of surround effects is comparable to
Dolby Digital 5.1.
Pro Logic II Music
This mode gives 5.1 channel surround sound
and is suitable for music. The surround effect is
more enveloping than Pro Logic II Movie.
Neo:6 Cinema (VSX-D811S only)
This mode gives 6.1 channel surround sound
and is suitable for movies. The Neo:6 Cinema
mode delivers good channel separation for
movie soundtracks.
Standard mode
The standard mode can be used to decode
Dolby Digital, DTS, or Dolby Surround sources.
The other surround sound options (next
column) can add multi-channel sound to
regular stereo sources.
You can identify Dolby Digital software by the
marks. Most Dolby
1 or
Surround software is marked 3, but
unmarked software may also incorporate Dolby
Surround. Depending on the source, the 6.1
channel setting (page 40), and the sound mode
you have selected, you may not get sound from
the surround back speakers in your setup. For
more on this, refer to the table on the next page.
Neo:6 Music (VSX-D811S only)
This mode gives 6.1 channel surround sound
and is suitable for music. The Neo:6 Music
mode plays the stereo source as is through the
front left/right speakers, and generates a
natural, ambient surround and center sound.
32
En
XRB3013A.32.37
32
01.12.12, 4:44 PM
Playing sources
05
Advanced Surround modes
Virtual Surround Back (VIRTL SB)
These are designed to be used with multichannel surround sound audio/visual sources
(like DVDs and LDs). Most Advanced Surround
modes are designed to be used with film
soundtracks, but some modes are also suited
for music sources. Try different settings with
various soundtracks to see which you like.
The Virtual Surround Back effect simulates 7.1
surround channel listening, giving the impression that there are two surround back speakers
in your system when listening to a 5.1 channel
source.
Expanded
Depending on the source, the 6.1 channel
setting (page 40), and the sound mode you have
selected, you may not get sound from the
surround back speakers in your setup. For more
on this, refer to the table below.
This mode is especially designed to give sound
depth to stereo sources, and lets you hear twochannel (stereo) signals as simulated multichannel surround sound. Use with Dolby Pro
Logic for a stereo surround effect. You can also
use with Dolby Digital sources for a wider
stereo field than the Standard modes.
Movie
5-Channel Stereo (VSX-D711)
Simulates the relaxed environment of a movie
theater, and is suitable for watching movies.
This can be selected to give multi-channel
sound to a stereo source, using all of the
speakers in your setup.
Music
Simulates the acoustic environment of a large
concert hall and is suitable for music or
musical sources.
6-Channel Stereo (VSX-D811S)
This can be selected to give multi-channel
sound to a stereo source, using all of the
speakers in your setup.
6.1 ch.
setting
Standard
DTS-ES/Dolby Digital Matrix encoded
multi-channel sources with 6.1 surround
Auto
√
√
√
√
Fix
√
√
√
√
Dolby Digital/DTS encoded multi-channel
sources with stereo surround
Auto
√
√
√
Dolby Digital/DTS encoded multi-channel
sources with mono surround, Stereo sources
Auto
Analog 2-channel (stereo) source
Auto
Type of source
Fix
Fix
Fix
√
Advanced
Virtual SB Expanded
Movie/Music
√
6 Ch.
Stereo
√
√
√
√
√
√
• The checkmark (√) indicates when sound will be output from the surround back speaker(s).
• See the 6.1 channel setting on page 40 to select between AUTO or FIX.
33
En
XRB3013A.32.37
33
01.12.12, 4:44 PM
05
Playing sources
Choosing the input signal
• You may get digital noise when a LD or CD
player compatible with DTS is playing an
analog signal. To prevent noise, make the
proper digital connections (page 14) and
set the signal input to DIGITAL.
You need to hook up a component to both
analog and digital inputs on the rear of the
receiver to select between input signals.
RECEIVER
SOURCE
DVD
• Some DVD players don’t output DTS
signals. For more details, refer to the
instruction manual supplied with your DVD
player.
TV
VCR
CD-R
MULTI CONTROL
RCV
TUN
CD
TVC
1
2
3
TEST TONE
INPUT ATT
FL DIMMER
4
5
6
CH SELECT
LEVEL
8
7
9
+10
EFFECT
DISPLAY
DISC
ENTER
D.ACCESS
T.EDIT/GUIDE
0
DTV INFO
MPX/RETURN
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
TOP MENU
¡
4
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
Listening to multi-channel
playback
¢
RECEIVER
SOURCE
REMOTE SETUP
INPUT SEL.
DVD
TV
VCR
CD-R
RECEIVER CONTROL
MULTI CONTROL
TUNE
ST
S ETU P
RCV
ST
TVC
1
2
3
TEST TONE
INPUT ATT
FL DIMMER
4
5
ENTER
TUNE
TUN
CD
6
CH SELECT
LEVEL
8
7
CHANNEL
9
+10
EFFECT
0
When set to DIGITAL, 2 DIGITAL lights when
a Dolby Digital signal is input, and DTS lights
when a DTS signal is input.
• This receiver can only play back Dolby
Digital, PCM (32kHz, 44kHz, 48kHz, and 96
kHz) and DTS digital signal formats. With
other digital signal formats, set to
ANALOG.
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
¡
4
¢
TOP MENU
REMOTE SETUP
INPUT SEL.
D.ACCESS
T.EDIT/GUIDE
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
RECEIVER CONTROL
Each press switches between AUTO, DVD 5.1
ch/DVD 7.1ch, ANALOG and DIGITAL. The
default is AUTO.
DVD 5.1ch (VSX-D711) and DVD 7.1ch (VSXD811S) will only appear when DVD/LD is
selected using the remote or the MULTI JOG/
INPUT SELECTOR dial on the front panel.
MPX/RETURN
1
•
Press SIGNAL SEL (SIGNAL SELECT) to
select the input signal corresponding to the
source component.
DISPLAY
DISC
ENTER
DTV INFO
TUNE
ST
S ETU P
ST
ENTER
TUNE
CHANNEL
1
Switch on the playback component.
2
Select the source you want to playback.
Use the MULTI CONTROL buttons on the
remote (or MULTI JOG/INPUT SELECTOR dial
on the front panel).
3
Press STANDARD.
If the source is Dolby Digital, DTS, or Dolby
Surround encoded, the proper decoding format
will automatically be selected and shows in the
display.
34
En
XRB3013A.32.37
34
01.12.12, 4:44 PM
Playing sources
05
If you are listening to a two channel source,
each press changes the display as follows:
Pro Logic II Movie
Pro Logic
II Music
Pro Logic
NEO:6
Music*
NEO:6
Cinema*
* VSX-D811S only
Using Advanced Surround
When you select one of the Advanced surround
options, Dolby Pro Logic, Dolby Digital and DTS
decoding is done automatically corresponding
to the input signal. Use Advanced surround to
add effects to the surround sound.
•
Press ADV.SURR. (ADVANCED SURROUND) repeatedly to cycle the sound
options.
Each press changes the display as follows:
Refer to page 32 for more details about each
mode.
Movie
Music
Virtual SB
4
Start playback of the component you
selected in step 1.
5-Stereo*/
6-Stereo**
Expanded
* VSX-D711
Using Stereo/Direct
When you select STEREO or DIRECT, you will
hear the source through just the front left and
right speakers (and possibly your subwoofer
depending on your speaker settings). Dolby
Digital and DTS multichannel sources are
downmixed to stereo. See page 32 for more on
these modes.
•
Press STEREO (STEREO/DIRECT on the
front panel) repeatedly to switch between
the two options.
** VSX-D811S
Refer to page 33 for more details about each
surround effect.
The Advanced surround effects can be
adjusted in the range of 10 to 90 (the
default setting is 70) by pressing RCV then
pressing EFFECT +/– . The effect level can
be set for each Advanced surround mode.
The Standard mode cannot be changed.
If you switch on Midnight listening,
Loudness, or the Tone controls when
DIRECT is selected, the receiver automatically switches to STEREO.
35
En
XRB3013A.32.37
35
01.12.12, 4:44 PM
05
Playing sources
Using Loudness and Midnight
listening
The Loudness listening feature can be used to
get good bass and treble from music sources at
low volume levels.
The Midnight listening feature allows you to
hear effective surround sound of movies at low
volume levels. The effect automatically adjusts
according to the volume at which you’re
listening.
2
Use the MULTI JOG/INPUT SELECTOR
dial to change the amount of bass or treble
as necessary.
Wait about five seconds for your changes to be
input automatically.
Playing other sources
RECEIVER
SOURCE
•
Press MIDNIGHT/LOUDNESS.
Each press cycles through the effects as
follows:
DVD
TV
VCR
TUN
CD
1
2
TEST TONE
INPUT ATT
4
5
3
6
7
3
8
DTV ON/OFF
DTV MENU
4
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
¢
TUNE
ST
Depending on what you are listening to, you
may want to adjust the bass or treble using the
front panel tone control.
N∫m-Û≥,,
S ETU P
ST
ENTER
TUNE
CHANNEL
1
Turn on the power of the playback
component.
INPUT
SELECTOR
MULTI JOG
2
ENTER
MASTER VOLUME
UP
DOWN
Turn on the power of the receiver.
3
Select the source you want to playback.
Use the MULTI CONTROL buttons on the
remote (or MULTI JOG/INPUT SELECTOR dial
on the front panel).
QUICK SETUP
MULTI JOG
VIDEO INPUT
AUDIO
¡
AUDIO
RECEIVER CONTROL
Using the tone controls
L
T.EDIT/GUIDE
CLASS
INPUT SEL.
VIDEO
DISPLAY
DISC
D.ACCESS
¶
TOP MENU
REMOTE SETUP
S-VIDEO
MPX/RETURN
ENTER
BAND
1
Loudness
TONE
9
EFFECT
0
DTV INFO
MONITOR
8
+10
Off
SPEAKERS
LEVEL
7
Midnight
TVC
FL DIMMER
CH SELECT
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
CD-R
MULTI CONTROL
RCV
R
R
4
Start playback of the component you
selected in step 1.
1
Press TONE to select the frequency you
want to adjust.
Each press switches between BASS and
TREBLE.
36
En
XRB3013A.32.37
36
01.12.12, 4:44 PM
Playing sources
05
Selecting the multi-channel
analog inputs
• When playback from the multi-channel
inputs is selected, only the volume and
channel levels can be set.
If you have connected a decoder or a DVD
player with multi-channel analog outputs to this
receiver (page 17), you must select the analog
multi-channel inputs for surround sound
playback.
RECEIVER
SOURCE
DVD
TV
VCR
CD-R
MULTI CONTROL
RCV
TUN
CD
TVC
1
2
3
TEST TONE
INPUT ATT
FL DIMMER
4
5
6
CH SELECT
LEVEL
8
7
9
+10
EFFECT
0
DISPLAY
DISC
ENTER
DTV INFO
MPX/RETURN
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
¡
4
¢
1
TOP MENU
REMOTE SETUP
INPUT SEL.
D.ACCESS
T.EDIT/GUIDE
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
RECEIVER CONTROL
TUNE
ST
S ETU P
ST
ENTER
TUNE
CHANNEL
1
Press DVD or select it with the MULTI
JOG/INPUT SELECTOR dial (front panel).
2
Press SIGNAL SEL (SIGNAL SELECT)
repeatedly to select DVD 5.1ch/DVD 7.1ch.
To cancel playback from the multi-channel
inputs, use the SIGNAL SEL (SIGNAL SELECT)
button to select a different input signal.
• When playback from the multi-channel
inputs is selected, you can’t use the INPUT
ATT, TONE, and MIDNIGHT/LOUDNESS
buttons, as well as the Standard,
Advanced Surround, and Stereo/Direct
sound modes.
37
En
XRB3013A.32.37
37
01.12.12, 4:44 PM
06
Setting up the receiver
Choosing your receiver setup
To ensure the best possible surround sound, be
sure to complete the following set up
operations. This is particularly important when
using Dolby surround. You only need to make
these settings once (unless you change the
placement of your current speaker system or
add new speakers, etc.). Refer to the following
pages for details on each of the settings.
If you are using the Pioneer S-FCRW220
speaker system, you’ll have to set the
Crossover frequency to 200kHz. You can
leave the Speaker setting and the
Subwoofer setting in the default settings.
DVD
TV
VCR
TUN
CD
1
2
TEST TONE
INPUT ATT
4
5
3
6
LEVEL
8
7
9
EFFECT
+10
0
DISPLAY
DISC
MPX/RETURN
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
INPUT SEL.
D.ACCESS
T.EDIT/GUIDE
¡
4
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
¢
RECEIVER CONTROL
TUNE
ST
S ETU P
ST
ENTER
TUNE
LFE attenuator setting (page 41)
Specify the peak level for the LFE channel.
Front speaker distance setting (page 41)
Specify the distance from your listening
position to your front speakers.
Center speaker distance setting (page
41)
Specifies the distance from your listening
position to your center speaker.
CHANNEL
1
Press
RECEIVER to turn the power
on.
The STANDBY indicator goes out.
2
Crossover frequency setting (page 40)
Determine which frequencies will be sent
to the subwoofer (or large speakers).
ENTER
DTV INFO
REMOTE SETUP
6.1 channel setting (VSX-D811S only)
(page 40)
Set when 6.1 channel decoding is used.
TVC
FL DIMMER
CH SELECT
1
Surround back speaker setting (VSXD811S only) (page 40)
Specify your surround back speaker/
surround back subwoofer setup.
Subwoofer setting (page 40)
Specify how the subwoofer is used.
CD-R
MULTI CONTROL
TOP MENU
Speaker setting (page 39)
Specify the number and type of speakers
you have connected.
RECEIVER
SOURCE
RCV
3
Use } or ] to choose the option you
want to adjust.
It will be easiest to adjust each of the settings in
turn, following the order below (and on the
following pages). The current setting is shown
for each option as you cycle through the
display.
Press RCV.
Surround speaker distance setting (page
41)
Specify the distance from your listening
position to your surround speakers.
Surround back speaker distance setting
(VSX-D811S only) (page 42)
Specifies the distance from your listening
position to your surround back speakers.
38
En
XRB3013A.38.44
38
01.12.12, 4:46 PM
Setting up the receiver
Dynamic range control setting (page 42)
Compress the dynamic range of the sound
track.
Dual mono setting (page 42)
Isolate one channel when listening to discs
with dual mono encoding.
Component video input setting (page
42)
Specify the components to be assigned to
the component video inputs (below).
• Component video 1 input setting
06
Speaker setting
• Default setting: S (all speakers)
You must let the receiver know how many
speakers you have, and how big they are. The
size you choose (large or small) determines
how much bass is sent from the receiver to the
speakers.
In the display, F, C, and S refer to front, center,
and surround speakers respectively. Speaker
size is denoted as L for large speakers, S for
small speakers, and (asterisk) if no speaker is
connected.
• Component video 2 input setting
Surround back channel input setting
(VSX-D811S only) (page 43)
Specify the number of surround back
inputs you have connected.
Digital input settings (page 43)
Specify the components to be assigned to
the video and digital inputs (below).
• Coaxial digital input 1 setting
• Coaxial digital input 2 setting
• If the cone size (diameter) of the speaker is
larger than 5 inches, set the speaker size
to L.
• If you’re not using a subwoofer, we
recommend setting the front speakers to L.
•
Cycle through the available choices
using ’ or ‘ and choose a configuration
that matches your speaker setup.
• Optical digital input 1 setting
• Optical digital input 2 setting (VSX-D811S
only)
4
Use ’ or ‘ to adjust the setting.
The setting is entered automatically.
5
Repeat steps 3 and 4 to set other
surround modes.
6
One of the following configurations should
match your setup:
FS-CS-SS
FL-C -SS
FS-CS-S
FL-C -SL
FS-C -SS
FL-CS-S
FL-CL-SL
FL-CS-SS
FL-CL-SS
FL-CS-SL
FL-CL-S
When you’re done, press ENTER to exit.
The setting display is automatically exited
after 20 seconds of inactivity.
39
En
XRB3013A.38.44
39
01.12.12, 4:46 PM
06
Setting up the receiver
Surround back speaker setting
Subwoofer setting
• Default setting: ON
(VSX-D811S only)
• Default setting: S
You must let the receiver know if surround back
speaker(s) have been connected, and how big
they are. The size you choose (large or small)
determines how much bass is sent from the
receiver to the speakers. If you have connected
a surround back subwoofer, you should select
the surround back subwoofer setting (SB
SUBWF) from the options. Choose (asterisk) if
no speaker is connected.
•
Use ’ or ‘ to select SB L, SB S, SB or
SB SUBWF.
You can choose whether the subwoofer is used
or not. Use the plus (PLS) setting for extra bass.
•
Use ’ or ‘ to select subwoofer ON, PLS
or OFF.
• If you chose the small front speaker
setting, SUBWF ON is automatically set
and locked.
• When you select the plus setting, you will
get the bass sounds from the subwoofer
even if the front speakers are set to L.
6.1 channel setting
(VSX-D811S only)
Crossover frequency setting
• Default setting: 6.1 FIX
• Default setting: 100 Hz
You can have the receiver automatically switch
to Dolby Digital or DTS-ES decoding for 6.1
encoded sources (6.1 AUTO), or you can
choose to listen to other kinds of sources (for
example, 5.1 encoded material) with 6.1
encoding (6.1 FIX). With 5.1 encoded sources, a
surround back channel will be generated, but
the material may sound better in the 5.1 format
for which it was originally encoded.
•
Use ’ or ‘ to select 6.1 FIX or 6.1
AUTO.
• If you chose SB in Surround back speaker
setting (above), you can’t set the 6.1
channel setting and
shows in the
display.
• Refer to the table on page 33 to see how
the 6.1 channel setting affects sound
output from the surround back speakers.
Crossover frequency is the point where the
receiver divides the high and low sounds (the
frequencies) between the speakers. Since most
smaller speakers can’t handle deep bass tones,
you can send these sounds to the subwoofer (or
if you don’t have a subwoofer, the large (L)
speakers in your system) instead of the
speakers set to small (S) in your setup. Choose
the point at which you want the frequency
routed to the subwoofer (or L speakers).
We recommend setting this to 200 Hz if your S
speakers are smaller bookshelf-type speakers.
•
Use ’ or ‘ to specify the crossover
frequency for your small speakers (100 Hz,
150 Hz or 200 Hz).
100Hz
150Hz
200Hz
100 Hz
Sends bass frequencies below 100 Hz to
the subwoofer (or L speakers).
40
En
XRB3013A.38.44
40
01.12.12, 4:46 PM
Setting up the receiver
150 Hz
Sends bass frequencies below 150 Hz to
the subwoofer (or L speakers).
200 Hz
Sends bass frequencies below 200 Hz to
the subwoofer (or L speakers).
If all speakers (front, center, and surround)
are set to L, the crossover frequency can’t
be set because there are no S speakers
appears in the display).
(
06
Center speaker distance setting
• Default setting: 10 ft.
The center speaker is normally placed directly
in the front of the listening room and closer to
the listening position than the front speakers.
This means that the sound from the center
speaker will be heard before the front speakers.
To prevent this, set the center speaker distance
setting to delay the sound from the center
speaker so that the sound from the front and
center speakers will be heard at the same time.
•
Use ’ or ‘ to set the distance of the
center speaker from the main listening
position (within a 30 foot range).
LFE attenuator setting
• Default setting: 0 dB
Dolby Digital and DTS audio sources include
ultra-low bass tones. Set the LFE attenuator as
necessary to prevent the ultra-low bass tones
from distorting the sound from the speakers.
•
Use ’ or ‘ to set the attenuation level
(0 dB, 10 dB or
dB(∞)).
0 dB
10 dB
∞ (displays
)
When ∞ is selected (
appears in the
display), LFE is not available.
Front speaker distance setting
• Default setting: 10 ft.
Sets the distance from the front speakers to the
listening position.
When C is selected in the speaker setting,
the center speaker distance can’t be set.
Surround speaker distance setting
• Default setting: 10 ft.
Like the center speaker, you should set the
distance of the surround speakers accurately to
hear sounds coming from both front and
surround speakers at the same time.
•
Use ’ or ‘ to set the distance of the
surround speakers from the main listening
position (within a 30 foot range).
When S is selected in the speaker setting,
the surround speaker distance can’t be
set.
•
Use ’ or ‘ to set the distance of the
front speakers from the main listening
position (within a 30 foot range).
41
En
XRB3013A.38.44
41
01.12.12, 4:46 PM
06
Setting up the receiver
Surround back speaker distance
setting
Dual mono setting
(VSX-D811S only)
The dual mono setting can only be used when
listening to Dolby Digital discs with dual mono
encoding. These discs are not widely used, but
are sometimes used when it is necessary to
have one language on one channel and a
different language on the other. With this
setting you can choose which channel in the
dual mono setting you want to listen to.
• Default setting: 10 ft.
Like the center speaker, you should set the
distance of the surround speakers accurately to
hear sounds coming from both front and
surround speakers at the same time.
•
Use ’ or ‘ to set the distance of the
surround speakers from the main listening
position (within a 30 foot range).
When SB is selected in the surround
speaker setting, the surround back
speaker distance can’t be set.
Dynamic range control setting
• Default setting: OFF
Dynamic range is the difference between the
loudest and softest sounds in any given signal.
With this setting, you can compress the
dynamic range, so that low level sounds can be
heard more easily (sounding relatively louder)
yet louder sounds won’t be too overbearing.
•
Press ’ or ‘ to set the dynamic range
control (OFF, MAX, or MID).
• Default setting: ch1
If Dolby Digital mode is switched on, you will
hear the channel you have selected (either ch1
or ch2) through your center speaker. With Dolby
Digital mode off, or if you don’t have a center
speaker, you will hear the channel you have
selected through both front speakers. In the L
ch 1. R ch 2 setting, the left front speaker will
play channel 1 and the right front speaker will
play channel 2.
•
Use ’ or ‘ to cycle through the
possible dual mono settings.
L ch 1.R ch 2
ch2
ch1
Component video input settings
Here you tell the receiver what components you
have hooked up to the component video jacks
on the back of the receiver.
• When the volume level is increased, set to
OFF.
Component video 1:
• When listening at low volumes, set to
MAX for maximum dynamic range
compression.
1
Use ’ or ‘ to assign the component
video 1 input (DVD, TV, VCR or OFF).
• Dynamic range control is effective only
when a Dolby Digital signal is being played
back.
Component video 2:
• Default settings: DVD
• Default setting: TV
2
Use ’ or ‘ to assign the component
video 2 input (DVD, TV, VCR or OFF).
42
En
XRB3013A.38.44
42
01.12.12, 4:46 PM
Setting up the receiver
Surround back channel input
setting
(VSX-D811S only)
• Default setting: SB 2ch IN
You only have to make this setting if you are
using a seperate component for decoding
DVDs, and the component has only one
surround back channel output. If this is the
case, select SB 1ch IN, otherwise leave it set to
SB 2ch IN.
•
Use ’ or ‘ to select SB 2ch IN or
SB 1ch IN.
06
Optical digital input settings
Here you tell the receiver what components you
have hooked up to the optical DIGITAL IN
jack(s) on the back of the receiver.
Optical digital 1:
• Default settings: TV/SAT
1
Use ’ or ‘ to assign the optical digital
1 input (DVD, TV, CD, CD-R, VCR or OFF).
Optical digital 2
(VSX-D811S only):
• Default setting: CDR/TAPE/MD
Coaxial digital input settings
Here you tell the receiver what components you
have hooked up to the coaxial DIGITAL IN jacks
1 and 2 on the back of the receiver.
Coaxial digital 1:
• Default settings: DVD/LD
2
Use ’ or ‘ to assign the optical digital
2 input (DVD, TV, CD, CD-R, VCR or OFF).
After you assign a component to a digital jack,
whenever you select that component, (for
example, a DVD player) the receiver
automatically changes to the digital input
setting and DIGITAL shows in the display.
1
Use ’ or ‘ to assign the coaxial digital
1 input (DVD, TV, CD, CD-R, VCR or OFF).
Coaxial digital 2:
• Default setting: CD
2
Use ’ or ‘ to assign the coaxial digital
2 input (DVD, TV, CD, CD-R, VCR or OFF).
After you assign a component to a digital jack,
whenever you select that component, (for
example, a DVD player) the receiver
automatically changes to the digital input
setting and DIGITAL shows in the display.
43
En
XRB3013A.38.44
43
01.12.12, 4:46 PM
06
Setting up the receiver
Setting the relative volume level
of each channel
• Default setting: 0db
RECEIVER
SOURCE
For best surround sound playback, you should
set the relative channel levels from the main
listening position. You can set seperate levels
for each surround mode.
DVD
TV
VCR
TUN
CD
1
2
TEST TONE
INPUT ATT
4
5
3
6
LEVEL
8
7
Press RCV.
TVC
FL DIMMER
CH SELECT
1
CD-R
MULTI CONTROL
RCV
9
+10
EFFECT
0
DTV INFO
2
Press TEST TONE to output the test
tone.
The test tone is output in the following order
(depending on the speaker setting):
MPX/RETURN
DISPLAY
DISC
ENTER
D.ACCESS
T.EDIT/GUIDE
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
TOP MENU
REMOTE SETUP
INPUT SEL.
¡
4
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
¢
RECEIVER CONTROL
TUNE
FL
C
FR
S ETU P
ST
ST
ENTER
SR
TUNE
CHANNEL
SW
SB*
SL
MENU
TV VOL
TV INPUT
*VSX-D811S only
MASTER VOLUME
TV
TV CONTROL
AV PRE-PROGRAMMED
REMOTE CONTROL UNIT
If you don’t hear a test tone from one of your
speakers, please refer to Speaker setting on
page 39 to make sure you have correctly
specified your speaker setup.
3
Press MASTER VOLUME +/– to adjust
the volume to an appropriate level.
4
Use LEVEL +/- to adjust the speaker
levels in turn.
You should hear the test tone at the same
volume from each speaker when seated in the
main listening position. The channel level range
is ± 10 dB.
• Test tone is only output in Standard
modes.
• Since the subwoofer transmits an ultralow frequency its sound may seem
quieter than it actually is.
5
When you’re done, press TEST TONE to
turn off the test tone.
The speaker volume can be adjusted without
outputting the test tone by pressing CH
SELECT and then using LEVEL +/–.
44
En
XRB3013A.38.44
44
01.12.12, 4:46 PM
Using the tuner
07
Listening to the radio
for about a second. The receiver will start
searching for the next station, stopping
when it has found one. Repeat to search
for other stations.
The following steps show you how to tune in to
FM and AM radio broadcasts using the
automatic (search) and manual (step) tuning
functions. If you already know the frequency of
the station you want, see Tuning directly to a
station below. Once you are tuned to a station
you can memorize the frequency for recall
later—see Saving station presets on the next
page for more on how to do this.
DVD
TV
VCR
Improving FM stereo sound
CD-R
MULTI CONTROL
TUN
CD
1
2
TEST TONE
INPUT ATT
4
5
FL DIMMER
6
LEVEL
8
7
9
+10
EFFECT
0
MPX/RETURN
DISPLAY
DISC
ENTER
D.ACCESS
T.EDIT/GUIDE
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
TOP MENU
REMOTE SETUP
INPUT SEL.
If the TUNED or STEREO indicators don't light
when tuning to an FM station because the
signal is weak, press the MPX(/RETURN)
button to switch the receiver into mono
reception mode. This should improve the sound
quality and allow you to enjoy the broadcast.
TVC
3
CH SELECT
DTV INFO
High speed tuning
Press and hold TUNE +/– for high speed
tuning. Release the button at the
frequency you want.
RECEIVER
SOURCE
RCV
Manual tuning
To change the frequency one step at a
time, press TUNE +/–.
¡
4
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
¢
Tuning directly to a station
RECEIVER CONTROL
Sometimes, you'll already know the frequency of
the station you want to listen to. In this case,
you can simply enter the frequency directly
using the number buttons on the remote
control.
TUNE
ST
S ETU P
ST
ENTER
TUNE
CHANNEL
1
Press the TUN button on the remote
control to select the tuner.
You can also use the MULTI JOG/INPUT
SELECTOR dial on the front panel.
2
Use the BAND button to change the
band (FM or AM), if necessary.
Each press switches the band between FM and
AM.
1
Press the TUN button on the remote
control to select the tuner.
You can also use the MULTI JOG/INPUT
SELECTOR dial on the front panel.
2
Use the BAND button to change the
band (FM or AM), if necessary.
Each press switches the band between FM and
AM.
3
3
Tune to a station.
There are three ways to do this:
Automatic tuning
To search for stations in the currently
selected band, press and hold TUNE +/–
Press D.ACCESS (Direct Access).
4
Use the number buttons to enter the
frequency of the radio station.
For example, to tune to 106.00 (FM), press 1, 0,
6, 0, 0.
45
En
XRB3013A.45.48
45
01.12.12, 4:48 PM
07
Using the tuner
STEREO
FM
TUNED
SP A
106.00
RECEIVER
SOURCE
DVD
TV
VCR
CD-R
MULTI CONTROL
If you make a mistake halfway through, press
D.ACCESS twice to cancel the frequency and
start over.
RCV
TUN
CD
TVC
1
2
3
TEST TONE
INPUT ATT
FL DIMMER
4
5
6
CH SELECT
LEVEL
8
7
9
EFFECT
+10
0
Saving station presets
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
N∫m-Û≥,,
INPUT
SELECTOR
MULTI JOG
MASTER VOLUME
MIDNIGHT/
LOUDNESS
MONITOR
SPEAKERS
TONE
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
¡
4
¢
TOP MENU
REMOTE SETUP
INPUT SEL.
D.ACCESS
T.EDIT/GUIDE
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
RECEIVER CONTROL
TUNE
ST
S ETU P
ST
ENTER
TUNE
CHANNEL
1
Tune to a station you want to memorize.
See Listening to the radio (previous page) for
more on this.
2
Press T.EDIT (TUNER EDIT).
The display shows ST. MEMORY, then a
blinking memory class.
ENTER
SIGNAL
SELECT
MPX/RETURN
1
If you often listen to a particular radio station,
it's convenient to have the receiver store the
frequency for easy recall whenever you want to
listen to that station. This saves the effort of
manually tuning in each time. This unit can
memorize up to 30 stations, stored in three
banks, or classes, (A, B and C) of 10 stations
each. When saving an FM frequency, the MPX
setting (see previous page) is also stored. Use
the front panel controls to store station presets.
DISPLAY
DISC
ENTER
DTV INFO
QUICK SETUP
UP
DOWN
MULTI JOG
VIDEO INPUT
STEREO
DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
R
A-
R
STATION
TUNING
STANDARD
ADVANCED
SURROUND
STEREO/
DIRECT
SIGNAL
SELECT
MIDNIGHT/
LOUDNESS
SPEAKERS
MONITOR
TONE
QUICK SETUP
MULTI JOG
LISTENING MODE
VIDEO INPUT
TUNER EDIT
CLASS
BAND
MPX
INPUT ATT
FL DIMMER
MULTI JOG
S-VIDEO
VIDEO
L
AUDIO
R
TUNED
SP A
99.50
3
Press CLASS to select one of the three
classes then press ST +/– (STATION +/–) to
select the station preset you want.
You can also use the the MULTI JOG/INPUT
SELECTOR dial (front panel) to select a station
preset.
4
Press ENTER.
After pressing ENTER, the preset class and
number stop blinking and the receiver stores
the station.
46
En
XRB3013A.45.48
46
01.12.12, 4:48 PM
Using the tuner
07
Naming station presets
Listening to station presets
For easier identification, you can name your
station presets.
Having stored up to 30 stations (see previous
page), preset stations can be easily recalled.
1
Choose the station preset you want to
name.
See Listening to station presets (this page) for
how to do this.
1
Press TUN (remote) or use the MULTI
JOG/INPUT SELECTOR dial on the front
panel to select the tuner.
2
Press T.EDIT (TUNER EDIT).
The display shows ST. NAME, then a blinking
cursor at the first character position.
2
Press CLASS to select the class in which
the station is stored.
Press repeatedly to cycle through classes A, B
and C.
3
Input the name you want.
Names can be up to four characters long.
3
Press ST +/– (STATION +/–) to select the
station preset you want.
• Use the MULTI JOG/INPUT SELECTOR dial
(front panel) or the ST +/- buttons (remote)
to select characters.
• Press ENTER to confirm a character. If no
character is input, a space is input.
• The name is stored when ENTER is
pressed after choosing the fourth
character.
• If the receiver is left disconnected from the
AC power outlet for an extended period,
the station memories will be lost and will
have to be reprogrammed.
To erase a station name, simply repeat steps
1-3 and input four spaces instead of a
name.
Once you have named a station preset, you
can press DISPLAY when listening to a
station to switch the display between the
name and the frequency.
47
En
XRB3013A.45.48
47
01.12.12, 4:48 PM
08
Making Recordings
Making an audio or a video
recording
automatically—check the component’s
instruction manual if you’re unsure.
You can make an audio or a video recording
from the built-in tuner, or from an audio or video
source connected to the receiver (such as a CD
player or TV).
5
Start recording, then start playback of
the source component.
Keep in mind you can’t make a digital recording
from an analog source or vice-versa, so make
sure the components you are recording to/from
are hooked up in the same way (see pages 13–
19 for more on connections).
RECEIVER
SOURCE
DVD
TV
VCR
TUN
CD
1
2
TEST TONE
INPUT ATT
4
5
TVC
3
FL DIMMER
6
CH SELECT
If you want to record a video source, you also
need use the same type of connection for the
source as for the recorder. For example, you
can’t record a component hooked up to S-video
jacks with a recorder hooked up to the component video outputs (see page 18 for more on
video connections).
CD-R
MULTI CONTROL
RCV
LEVEL
8
7
9
+10
EFFECT
0
DTV INFO
MPX/RETURN
DISPLAY
DISC
ENTER
D.ACCESS
T.EDIT/GUIDE
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
TOP MENU
REMOTE SETUP
INPUT SEL.
¡
4
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
¢
RECEIVER CONTROL
TUNE
ST
S ETU P
ST
ENTER
TUNE
CHANNEL
The receiver's volume, balance, tone (bass,
treble, loudness), and surround effects
have no effect on the recorded signal.
1
Select the source you want to record.
Use the MULTI CONTROL buttons on the
remote (or MULTI JOG/INPUT SELECTOR dial
on the front panel).
2
Select the input signal (if necessary).
Press SIGNAL SEL (SIGNAL SELECT) to select
the input signal corresponding to the source
component (see page 34 for more on this).
Monitoring your recording
You can listen to (monitor) the recording as it's
being made using the MONITOR button on the
front panel (a cassette deck would have to have
a record monitor function).
•
Press the MONITOR button to switch
between the recorded signal and the
original source signal.
3
Prepare the source you want to record.
Tune to the radio station, load the CD, video,
DVD etc.
4
Prepare the recorder.
Insert a blank tape, MD, video etc. into the
recording device and set the recording levels.
Refer to the instructions that came with the
recorder if you are unsure how to do this. Most
video recorders set the audio recording level
48
En
XRB3013A.45.48
48
01.12.12, 4:48 PM
Controlling the rest of your system
Setting the remote to control
other components
09
Selecting preset codes
directly
There are several ways to set your remote to
control the other components in your system.
The easiest way to do this is to assign the
component’s manufacturer preset code (listed
on pages 56–67) to one of the MULTI CONTROL
buttons on the remote control.
The buttons can be set to control the following
components:
RECEIVER
SOURCE
DVD
TV
VCR
CD-R
MULTI CONTROL
RCV
TUN
CD
1
2
TEST TONE
INPUT ATT
4
5
TVC
3
FL DIMMER
6
CH SELECT
LEVEL
8
7
9
EFFECT
+10
0
Button Controllable Components
MPX/RETURN
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
¡
4
1
TOP MENU
DVD:
TV:
VCR:
CD:
CD-R:
TVC:
TUN:
DVD or LD player
TV or Satellite tuner
VCR or Digital Video Recorder
CD player
CD Recorder, Tape deck
or MD player
TV or Cable TV tuner
FM/AM tuner
You can do this directly, or by searching
through different preset codes until you find the
right one. If you can’t find a preset code that
matches the component you want to control,
you can still teach the remote individual
commands from another remote control (page
50).
You can cancel or exit any of the steps by
pressing and holding MUTE for three seconds.
DISPLAY
DISC
ENTER
DTV INFO
AUDIO
REMOTE SETUP
INPUT SEL.
D.ACCESS
T.EDIT/GUIDE
¢
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
RECEIVER CONTROL
TUNE
ST
S ETU P
ST
ENTER
TUNE
CHANNEL
1
Press and hold REMOTE SETUP for three
seconds.
The LED lights steadily for two seconds.
2
Press the MULTI CONTROL button for
the component you want to control.
3
Use the number buttons to enter the 4
digit preset code (see pages 56–67)
The LED blinks for half a second after you input
each digit and shows a long, two second blink
once you have entered a valid code. If the LED
blinks three times it means an invalid code has
been input or an error has occurred.
• If you assign a preset code for the TUNER
button, you won’t be able to control the
built-in tuner of this receiver using the
remote. Reset the remote to the built-in
tuner by entering the preset code 7008.
4
Repeat steps 1 through 3 for the other
components you want to control.
49
En
XRB3013A.49.67
49
01.12.12, 4:48 PM
09
Controlling the rest of your system
Searching for preset codes
Another way of entering preset codes is to use
the search feature. The remote transmits
batches of 10 codes; when you see the
component you want to control respond (by
turning on or off), you just scan through the last
10 codes until you find the right one.
RECEIVER
SOURCE
DVD
TV
VCR
TUN
CD
1
2
TEST TONE
INPUT ATT
4
5
TVC
3
6
LEVEL
8
9
EFFECT
+10
0
DTV INFO
MPX/RETURN
DISPLAY
DISC
ENTER
D.ACCESS
T.EDIT/GUIDE
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
¡
4
¢
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
TOP MENU
REMOTE SETUP
INPUT SEL.
RECEIVER CONTROL
TUNE
ST
You can also verify you have the correct code by
adjusting the volume, pressing 3, 7, etc.
FL DIMMER
CH SELECT
7
6
Use ’ and ‘ to scan through the last
10 codes transmitted to identify the correct
code.
Stop when you see the component stop or
switch off. The LCD display on the remote
shows the I.D.
7
Press and hold ENTER for three seconds
to save the preset code.
CD-R
MULTI CONTROL
RCV
5
Switch the component back on or
restart playback.
S ETU P
ST
ENTER
TUNE
CHANNEL
1
Switch on the component you want to
control.
If the component is some kind of player (CD
player, VCR, etc.), start it playing.
2
Press and hold REMOTE SETUP for three
seconds.
The LED lights steadily for two seconds.
3
Press the MULTI CONTROL button for
the component you want to control.
4
Press and hold REMOTE SETUP for three
seconds.
A batch of 10 codes is transmitted and the LED
blinks during transmission. If the component
responds, by stopping or switching off, go to the
next step, otherwise repeat this step.
Programming signals from
other remote controls
(VSX-D811S only)
If the preset code for your component is not
available, or the available preset codes do not
operate correctly, you can program signals from
the remote control of another component. This
can also be used to program additional
operations (buttons not covered in the presets)
after assigning a preset code.
1
Press REMOTE SETUP and hold for three
seconds.
The LED lights steadily for two seconds.
2
Press the MULTI CONTROL button for
the component you want to control.
3
Prepare the remote to learn the remote
control signal from the component.
Press and hold the RECEIVER button for two
seconds.
The LED lights steadily to indicate the remote is
ready accept a signal.
To exit or cancel press and hold the REMOTE
SETUP key for three seconds.
50
En
XRB3013A.49.67
50
01.12.12, 4:48 PM
Controlling the rest of your system
MASTER VOLUME
TV
MENU
TVFUNC
CHANNEL
AV PRE-PROGRAMMED AND LEARNING
REMOTE CONTROL UNIT
TUNE
TV CONTROL
VOLUME
8
¢
ST
ENTER
TUNE
ST
GUIDE
MUTING
FUNCTION
DTV MENU
SETUP
FL DIMMER
LOUDNESS
6
9
TEST TONE SIGNAL SELECT
CH LEVEL
DSP
2 /DTS
CH SELECT
3
3
4
¡
DTV ON/OFF
7
CLASS
¶
BAND
1
TVC
ATT
CD-R
DISC
ENTER
RECEIVER
D.ACCESS
0
MPX/RETURN
10
DTV INFO
TUN
EFFECT
5
8
VCR
2
5.1 / 7.1
TV
CD
4
7
MULTI CONTROL
1
DVD
SOURCE
RCV
1 - 2 inches
MIDNIGHT
4
Point the two remote controls towards
each other about 1-2 inches apart then
press the button that will be doing the
learning on this receiver’s remote control
(for example 3, 7, etc.).
The LED flashes rapidly.
5
Press the corresponding button on the
other remote control that is sending
(teaching) the signal to this receiver’s
remote control (for example 3, 7, etc.).
If the operation has been learned successfully,
the LED on this receiver’s remote will go out
and then light steadily.
If for some reason the operation hasn’t been
learned the LED will blink for three seconds and
then light steadily. If this happens, keep
pressing the (teaching) button as you vary the
distance between the two remotes, until you
see the the LED light steadily.
To program additional operations for the current
component repeat steps 4 and 5.
To program operations for another component
exit and repeat steps 1 through 5.
6
Press and hold the REMOTE SETUP
button for three seconds to store the
operation(s).
09
• TV CONTROL buttons (TV , TV VOL +/-,
and TV INPUT) can only be learned after
selecting TV or TVC.
Erasing one of the remote
control button settings
(VSX-D811S only)
This erases one of the buttons you have
programmed and restores the button to the
factory default.
1
Press REMOTE SETUP and hold for three
seconds.
The LED lights steadily for two seconds.
2
Press the MULTI CONTROL button
relating to the button setting to be erased.
3
Prepare the remote to erase the button
setting.
Press the RECEIVER button twice quickly.
The LED blinks to indicate the remote is ready
to erase the button setting.
4
Press and hold the button to be erased
for three seconds.
The LED lights steadily for three seconds and
then goes off.
5
Repeat step 4 to erase other buttons.
6
Press and hold the REMOTE SETUP
button for two seconds to exit.
• Some commands from other remote
controls cannot be learned, but in most
cases the remotes just need to be moved
closer together or farther apart.
Clearing all the remote
control settings
• Certain buttons represent operations that
cannot be learned from other remote
controls. These include: RECEIVER ,
REMOTE SETUP and the MULTI
CONTROL, RECEIVER CONTROL and
MASTER VOLUME buttons.
1
Press REMOTE SETUP and hold for three
seconds.
The LED lights steadily for two seconds.
You can clear all presets and restore the factory
default settings.
51
En
XRB3013A.49.67
51
01.12.12, 4:49 PM
09
Controlling the rest of your system
2
Press any MULTI CONTROL button then
use the number buttons to enter 0123.
The LED lights for two seconds to indicate that
the settings have been restored to the factory
presets. (If the LED blinks three times, then you
made a mistake with the code—try re-entering
it.)
Confirming preset codes
Use this feature to check which preset code is
assigned to a MULTI CONTROL button.
1
Press REMOTE SETUP and hold for three
seconds.
The LED lights steadily for two seconds.
2
Press the MULTI CONTROL button of the
component for which you want to check the
preset code.
Direct function
• Default setting: ON
You can use the direct function feature to
control one component using the remote
control while at the same time, using your
receiver to playback a different component. This
could let you, for example, use the remote
control to set up and listen to a CD on the
receiver and then use the remote control to
rewind a tape in your VCR while you continue to
listen to your CD player.
3
Press and hold ENTER for two seconds.
Each preset code consists of four digits, for
example 1329. Each digit will be represented by
a series of blinks on the remote’s LED—3 blinks
to represent the digit “3”, etc. (“0” is
represented by 10 blinks)
When direct function is on, any component you
select (using the MULTI CONTROL buttons )
will be selected by both the receiver and the
remote control. When you turn direct function
off, you can operate the remote control without
affecting the receiver.
1
Press REMOTE SETUP and hold for three
seconds.
The LED lights steadily for two seconds.
2
Press the MULTI CONTROL button for
the component you want to control.
3
Use the number buttons to enter either
9990 (direct on) or 9995 (direct off).
The LED will light for two seconds to indicate
that it’s been correctly set. (If the LED blinks
three times, then there was a mistake with the
code—repeat steps 1-4.)
You can’t use direct function for TV INPUT.
52
En
XRB3013A.49.67
52
01.12.12, 4:49 PM
Controlling the rest of your system
09
Controls for TVs
This remote control can control components after entering the proper codes or teaching the
receiver the commands (see pages 56–67). Use the MULTI CONTROL buttons to select the
component.
Button (s)
TV
Function
Components
Switches the DTV on or off.
DTV
Switches the TV or CATV between standby and on.
Cable TV/Satellite TV/TV
TV INPUT
Switches the TV input. (Not possible with all models.)
TV
CHANNEL
+/–
Selects channels.
Cable TV/Satellite TV/TV/
DTV
TV VOL
+/–
Adjust the TV volume.
Cable TV/Satellite TV/TV/
DTV
SOURCE
Press to switch the component assigned to the TVC
button on or off.
DTV
4
Switches DTV on or off.
DTV
¢
Press to display the DTV menu.
DTV
8
Use as the GUIDE button for navigating
DTV
¶
Press to get information on DTV programs.
DTV
TOP MENU Use to choose the BLUE commands on a DTV menu.
DTV
AUDIO
Use to choose the GREEN commands on a DTV menu.
DTV
SUB TITLE
Use to choose the RED commands on a DTV menu.
DTV
ANGLE
Use to choose the YELLOW commands on a DTV menu.
DTV
¡
Selects between screen formats for widescreen TVs.
TV
1
Use to clear a TV channel selected using the number
buttons.
Cable TV/TV
3
Use to switch DTV audio tracks
DTV
7
Use to select closed captioning with DTV.
DTV
Number
Buttons
Use to select a specific TV channel.
Cable TV/Satellite TV/TV/
DTV
+10 button Use to add a decimal point when selecting a specific TV
channel.
DTV
ENTER/
DISPLAY/
DISC
Cable TV/Satellite TV/TV
Use to enter a channel.
53
En
XRB3013A.49.67
53
01.12.12, 4:49 PM
09
Controlling the rest of your system
Button (s)
MENU
Function
Components
Select different menus from the DTV functions.
DTV
Select the menu screen.
Cable TV/Satellite TV/TV
}]’‘ & Select or adjust and navigate items on the menu screen.
ENTER
ENTER brings up the DTV menus.
DTV
Press to select or adjust and navigate items on the menu
screen.
EFFECT
+/–
Cable TV/Satellite TV/TV/
DTV
For TV and cable TV use this button to immediately enter Cable TV/Satellite TV/TV/
a new channel (CHANNEL ENTER function). For satellite
DTV
TV use this button to exit the menu screen.
The four TV CONTROL buttons on the remote control are dedicated to control the TV assigned to
the TVC button. Thus if you only have one TV to hook up to this system assign it to the TVC
MULTI CONTROL button. If you have two TVs, assign the main TV to the TVC button.
Controls for other components
This remote control can control these components after entering the proper codes or teaching the
receiver the commands (see pages 56–67). Use the MULTI CONTROL buttons to select the
component.
Button (s)
Function
Components
SOURCE
Press to switch the component between standby and on. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
4
Press to return to the start of the current track.
Repeated presses skips to the start of previous tracks.
CD/MD/CD-R/DVD/LD player
Go back channels (channel –).
VCR/DVR
Play the reverse side of the tape on a reversible deck.
Cassette deck
Press to advance to the start of the next track.
Repeated presses skips to the start of following tracks.
CD/MD/CD-R/LD player
Go forward channels (channel +).
VCR
¢
Play the forward side of the tape on a reversible deck.
Cassette deck
8
Pause playback or recording.
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
3
Start playback.
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
54
En
XRB3013A.49.67
54
01.12.12, 5:24 PM
Controlling the rest of your system
Button (s)
Function
09
Components
¡
Hold down for fast forward playback.
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
1
Hold down for fast reverse playback.
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
7
Stops playback (on some models, pressing this when the
disc is already stopped will cause the disc tray to open).
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
¶
Starts recording. To prevent accidental recording, this
button must be pressed twice to take effect (the second
press must be within 10 seconds of the first).
VCR/DVR player
Number
buttons
Directly access tracks on a program source.
CD/MD/CD-R/VCR/LD player
Use the number buttons to navigate the on-screen
display.
DVD/DVR player
+10 button Selects tracks higher than 10. (For example, press +10
then 3 to select track 13.)
CD/MD/CD-R/VCR/LD player
ENTER
Multiple CD player
Chooses the disc.
(DISPLAY/ Ejects the disc.
MD player
DISC)
Use as the ENTER button.
VCR
Displays the setup screen for DVD/DVR players.
DVD/DVR player
Changes sides of the LD.
LD player
MENU
Displays menus concerning the current DVD or DVR you
are using.
DVD/DVR player
’
Pauses the tape.
CD-R/Cassette deck
‘
Stops the tape.
CD-R/Cassette deck
ENTER
Starts playback.
CD-R/Cassette deck
}/]
Fast rewinds/fast forwards the tape.
CD-R/Cassette deck
}]’‘ & Navigates DVD menu/options.
ENTER
DVD/DVR Player
CHANNEL Selects channels.
VCR/DVD/DVR Player
+/–
CD/MD/CD-R/Cassette deck
Selects tracks.
TOP MENU Displays the disc ‘top’ menu of a DVD.
DVD/DVR Player
AUDIO
Changes the audio language or channel.
DVD/DVR Player
SUBTITLE
Displays/changes the subtitles on multilingual DVDs.
DVD/DVR Player
ANGLE
Switches camera angles on discs with multi-angle scenes. DVD/DVR Player
55
En
XRB3013A.49.67
55
01.12.12, 4:49 PM
09
Controlling the rest of your system
Preset Code List
You can only set these codes for the buttons that assigned to the respective components. So, for
example, the TV codes can only be set to the TV or TVC button.
TV
Manufacturer
PHILIPS
SONY
PANASONIC
TOSHIBA
TELEFUNKEN
SHARP
SAMSUNG
FERGUSON
MITSUBISHI
GOLDSTAR
BLAUPUNKT
RADIOLA
JVC
DAEWOO
ORION
SIEMENS
ADMIRAL
ADYSON
AIKO
AKAI
AKURA
ACURA
ALARON
ALBA
ALLORGAN
ANAM
56
ANAM NATIONAL
AMBASSADOR
AMERICA ACTION
TV
TVC
Code
1008, 1017, 1020, 1025, 1104,
1115
1001, 1007, 1016
1023, 1054, 1055, 1075, 1076,
1082, 1087, 1121, 1124
1015, 1016, 1027, 1031, 1050,
1051, 1085
1005, 1026, 1034, 1038, 1042,
1046, 1075, 1097
1016, 1019, 1041, 1056, 1124
1006, 1011, 1013, 1017, 1026,
1027, 1039, 1062, 1079, 1089,
1092, 1102
1005, 1017, 1033, 1046, 1065,
1084, 1091
1011, 1016, 1041, 1045, 1049,
1062, 1114
1002, 1011, 1013, 1017, 1019,
1026, 1046, 1062, 1079, 1092
1066, 1068, 1071, 1075, 1115
1008, 1017
1016, 1024, 1030, 1053, 1065,
1067, 1103, 1122
1006, 1011, 1017, 1019, 1028,
1040, 1050, 1104, 1110, 1118,
1119
1017, 1063, 1083, 1095, 1098,
1099, 1112
1017, 1052, 1066, 1068, 1071,
1075, 1115
1041, 1055, 1075, 1112
1014, 1079
1040
1013, 1074
1080, 1089
1006
1063, 1078
1006, 1016, 1017, 1080, 1103
1095
1004, 1006, 1029, 1054, 1064,
1087, 1108
1054, 1087, 1108
1061
1064
AMPLIVISION
AMPRO
AMSTRAD
ANITECH
AOC
ARCAM
ASBERG
ASUKA
ATLANTIC
AUDIOSONIC
AUDIOVOX
AUTOVOX
BANG & OLUFSEN
BASIC LINE
BAYSONIC
BAUR
BEKO
BELCOR
BELL & HOWELL
BEON
BINATONE
BLUE SKY
BLUE STAR
BONDSTEC
BOOTS
BPL
BSR
BRADFORD
BRANDT
BRITANNIA
BROCKWOOD
BROKSONIC
BTC
BUSH
CANDLE
CARNIVALE
CARREFOUR
CARVER
CASCADE
CATHAY
CENTURY
CENTURION
CELEBRITY
CCE
CGE
CIMLINE
1079
1126
1006, 1017, 1103, 1105
1006, 1029, 1036
1011, 1013
1078, 1079
1036
1080
1073
1017, 1046
1040, 1064, 1110 , 1118
1036, 1073
1116
1006, 1080
1064
1007, 1017, 1114, 1115
1102
1011
1009, 1050
1017
1079
1080
1090
1086
1079
1090
1095
1064
1046, 1069, 1070, 1072
1078
1011
1083, 1112
1080
1006, 1016, 1017, 1080, 1090,
1095, 1103, 1104
1013, 1026
1013
1016
1025, 1058
1006
1017
1075
1017
1001
1017
1034, 1036, 1038, 1086, 1097
1006
En
XRB3013A.49.67
56
01.12.12, 4:49 PM
Controlling the rest of your system
CINERAL
1040, 1110
CITIZEN
1013, 1019, 1026, 1027, 1040
CLARIVOX
1017
CLATRONIC
1036, 1086, 1102
CME
1007, 1015, 1114
CONCERTO
1026
CONDOR
1098, 1102
CONTEC
1006, 1016, 1064, 1078
CONTINENTAL EDISON 1069, 1070, 1072
CRAIG
1054
CROSLEY
1025, 1034, 1036, 1038, 1075
CROWN
1006, 1017, 1019, 1036, 1064,
1102, 1106
CRYSTAL
1109
CS ELECTRONICS 1078
CTC
1086
CURTIS MATHES
1009, 1013, 1019, 1022, 1023,
1025, 1026, 1027, 1041, 1047,
1050, 1057, 1110, 1113, 1129,
1131
CYBERTRON
1080
CXC
1064
DAINICHI
1077, 1080
DANSAI
1017
DAYTRON
1006, 1011
DECCA
1017, 1032
DE GRAAF
1074
DENON
1047
DIXI
1006, 1017
DUAL TEC
1079
DUMONT
1010, 1011, 1031
DWIN
1125, 1127
ECE
1017
ELBE
1088
ELECTROBAND
1001
ELIN
1017
ELITE
1080, 1098
ELTA
1006
EMERSON
1011, 1018, 1019, 1050, 1061,
1062, 1063, 1064, 1075, 1083,
1090, 1112, 1118, 1119
ENVISION
1013
ERRES
1008, 1017
ETRON
1006, 1120
EXPERT
1073
FIDELITY
1078
FINLANDIA
1074
FINLUX
1017, 1031, 1032 , 1044
FISHER
1050, 1074, 1079, 1096, 1102
FLINT
1111
FORMENTI
1017, 1075, 1098
FORTRESS
1041
09
FRONTECH
FUJITSU
FUNAI
1055, 1086, 1089, 1109
1032, 1063, 1073
1059, 1063, 1064, 1089, 1095,
1096
FUTURETECH
1064
GE
1012, 1022, 1023, 1041, 1062,
1090, 1110, 1129, 1131
GEC
1017, 1020, 1032, 1072, 1079
GELOSO
1006, 1075
GENEXXA
1055, 1080
GIBRALTER
1010, 1011, 1013
GOODMANS
1016, 1017, 1032, 1079, 1103,
1104
GORENJE
1102
GPM
1080
GRAETZ
1055
GRANADA
1017, 1032, 1048, 1074, 1079,
1100
GRADIENTE
1024, 1026, 1058
GRANDIN
1090
GRUNDIG
1031, 1066, 1068, 1072, 1115
GRUNPY
1063, 1064
HALLMARK
1062
HANSEATIC
1017, 1098
HARLEY DAVIDSON 1063
HARVARD
1029, 1064
HARMAN/KARDON 1025
HCM
1006, 1090, 1105
HINARI
1006, 1016, 1017, 1080
HISAWA
1090, 1111
HITACHI
1014, 1016, 1018, 1020, 1021,
1026, 1044, 1046, 1047, 1055,
1069, 1070, 1079, 1081, 1097
HUANYU
1078, 1104
HYPSON
1017, 1089, 1090
ICE
1079, 1089, 1103
ICES
1080
IMPERIAL
1034, 1036, 1038, 1086, 1102,
1106
INDIANA
1017
INFINITY
1025
INGELEN
1055
INNO HIT
1032
INNOVA
1017
INTEQ
1010
INTERBUY
1029
INTERFUNK
1017, 1055, 1086, 1114
INTERVISION
1017, 1029, 1043
1079, 1089
ISUKAI
1080
ITS
1103
ITT
1055
57
En
XRB3013A.49.67
57
01.12.12, 4:49 PM
09
Controlling the rest of your system
JBL
JCB
KAISUI
KAMP
KAPSCH
KAWASHO
KEC
KENDO
KNEISSEL
KENWOOD
KINGSLEY
KONIG
KORPEL
KOYODA
KTV
LEYCO
LG
LIESENK&TTER
LLOYTRON
LOEWE
LOGIK
LUMA
LUXMAN
LXI
M ELECTRONIC
MAGNAVOX
MAGNADYNE
MAGNAFON
MAJESTIC
MANESTH
MARANTZ
MARK
MATSUI
MATSUSHITA
MCMICHAEL
MEDIATOR
MEGATRON
MEMOREX
METZ
MGA
MIDLAND
MINERVA
MINOKA
MINUTZ
MIVAR
MOTION
MOTOROLA
MTC
58
MULTITECH
1025
1001
1006, 1078, 1079, 1080, 1090,
1078
1055, 1073
1078
1064
1017
1088
1011, 1013
1078
1114
1017
1006
1013, 1019, 1064
1017, 1032, 1089, 1095
1026
1017
1014
1035, 1114
1009
1073
1026
1022, 1025, 1050, 1051, 1062
1006, 1017, 1029, 1044, 1046,
1055, 1079, 1091, 1104
1013, 1016, 1025, 1063
1043, 1086
1036, 1043, 1075
1009
1079, 1089, 1098
1013, 1017, 1025
1017
1006, 1015, 1016, 1017, 1032,
1074, 1079, 1095, 1103
1087
1020
1008, 1017
1047, 1062
1006, 1009, 1026, 1049, 1050,
1062, 1087, 1112
1075
1011, 1013, 1049, 1062
1010, 1019, 1022, 1023
1031, 1115
1105
1012
1078, 1092, 1093, 1094
1036
1041
1011, 1013, 1026, 1027, 1078,
1114
1006, 1036, 1043, 1064, 1078
NAD
NEC
NECKERMANN
NEI
NETSAT
NICAMAGIC
NIKKAI
NIKKO
NOBLIKO
NORDMENDE
NTC
OCEANIC
ONWA
OPTIMUS
OPTONICA
OSAKI
OSO
OSUME
OTTO
OTTO VERSAND
PALLADIUM
PANAMA
PATHE MARCONI
PATHE CINEMA
PAUSA
PENNEY
PERDIO
PHAPSODY
PHASE
PHILCO
PHONOLA
PILOT
PORTLAND
PRISM
PROFEX
PROLINE
PROSOCAN
PROTECH
PROTON
PULSAR
PYE
QUASAR
QUELLE
QUESTA
R-LINE
1051, 1057, 1062
1011, 1013, 1016, 1026, 1058
1017, 1066, 1075, 1115
1017, 1109
1017
1078
1014, 1015, 1017, 1032, 1078,
1080, 1089
1013, 1040, 1062
1036, 1043
1046, 1069, 1070, 1075, 1091
1040
1055, 1077
1064
1050, 1057, 1087
1041, 1056
1014, 1032, 1079, 1080, 1089,
1105
1080
1014, 1032, 1052
1007, 1114
1007, 1016, 1017, 1066, 1075,
1079, 1098, 1115
1102, 1106
1079, 1089
1069, 1070, 1072
1075, 1078, 1084, 1098
1006
1003, 1011, 1012, 1013, 1019,
1022, 1023, 1026, 1027, 1051,
1062, 1131
1098
1078
1014
1011, 1013, 1025, 1034, 1036,
1038, 1047, 1075, 1086, 1112
1008, 1017
1011, 1013, 1019
1011, 1019, 1040
1023
1006, 1037
1099
1022
1006, 1017, 1043, 1079, 1086,
1089, 1106, 1109
1062, 1113
1010, 1011
1008
1023, 1056, 1087
1007, 1017, 1031, 1034, 1038,
1071, 1075, 1097, 1114, 1115
1016
1017
En
XRB3013A.49.67
58
01.12.12, 4:49 PM
Controlling the rest of your system
RANK ARENA
RBM
RCA
REALISTIC
REX
REVOX
ROADSTAR
RUNCO
SABA
SACCS
SAISHO
SALORA
SAMBERS
SAMPO
SAMSUX
SANDRA
SANSEI
SANSUI
SANYO
SBR
SCHNEIDER
SCIMITSU
SCOTCH
SCOTT
SEARS
SEG
SEI
SEI-SINUDYNE
SELECO
SEMIVOX
SEMP
SENTRA
SHOGUN
SHORAI
SSS
SIAREM
SINDYNE
SIGNATURE
SILVER
SKY
SKY-WORTH
SOLAVOX
SONITRON
SONOKO
SONOLOR
SONTEC
SOUNDESIGN
XRB3013A.49.67
1016
1031
1011, 1018, 1022, 1023, 1039,
1041, 1128, 1129, 1130, 1131,
1132
1011, 1013, 1019, 1026, 1050,
1056, 1062, 1064
1055, 1073, 1088, 1089
1017
1006, 1080, 1089, 1106
1010, 1013, 1117
1035, 1046, 1055, 1069, 1070,
1072, 1075, 1091
1084
1006, 1089, 1109
1055
1036, 1043, 1075
1013, 1019
1019
1078
1110
1112
1016, 1032, 1048, 1050, 1052,
1074, 1075, 1100
1008, 1017, 1020
1017, 1080, 1086, 1096, 1103
1011
1062
1011, 1062, 1063, 1064, 1083
1022, 1025, 1026, 1050, 1051,
1059, 1062, 1063
1016, 1036, 1079, 1089
1043, 1075, 1095
1007
1055, 1073, 1088
1064
1051
1015
1011
1095
1011, 1064
1043, 1075
1043, 1075, 1095
1009
1016
1017
1017
1014, 1055
1074
1006, 1017
1055, 1074, 1077
1017
1062, 1063, 1064
59
09
SOUNDWAVE
SQUAREVIEW
STANDARD
STARLITE
STERN
SUNKAI
SUPERTECH
SUPREME
SUSUMU
SYLVANIA
SYMPHONIC
SYSLINE
TANDY
TASHIKO
TEC
TECHNEMA
TECHNICS
TECHNOL ACE
TECHWOOD
TEKNIKA
1017, 1106
1059
1006, 1079, 1080
1064
1055, 1073, 1088
1095, 1099
1078
1001
1080
1013, 1025
1059
1017
1032, 1041, 1055, 1079, 1080
1016, 1020, 1079
1079, 1086
1098
1023, 1087, 1121
1063
1023, 1026
1009, 1011, 1019, 1025, 1026,
1027, 1040, 1049, 1063, 1064
TELEAVIA
1072
TELEMEISTER
1098
TELETECH
1006
TELETON
1016, 1073, 1079
TENSAI
1080, 1095, 1098
TEXET
1078, 1080
THOMSON
1046, 1069, 1070, 1072, 1091
THORN
1015, 1017, 1032, 1034, 1038,
1065, 1067, 1114
TMK
1026, 1061, 1062
TOMASHI
1090
TOTEVISION
1019
TRIUMPH
1085
TUTUNG
1017, 1032, 1079
UHER
1073, 1096, 1098
ULTRA
1067
ULTRAVOX
1043
UNIVERSUM
1017, 1044, 1089, 1102
VECTOR RESEARCH 1013
VESTEL
1017
VICTOR
1016, 1024, 1053, 1087
VIDEOSAT
1086
VIDEOTECHNIC
1079
VIDIKRON
1025
VIDTECH
1011, 1016, 1062
VISION
1098
VOXSON
1055
WALTHAM
1079
WATSON
1017, 1098
WATT RADIO
1043
WARDS
1009, 1011, 1012, 1013, 1025,
1026, 1056, 1062, 1063
WEGA
1016
01.12.12, 4:49 PM
59
En
09
Controlling the rest of your system
WHITE WESTINGHOUSE 1017, 1078, 1098, 1112,
1118, 1119
YAMAHA
1011, 1013
YOKO
1017, 1079, 1101, 1109
ZANUSSI
1073
ZENITH
1009, 1010, 1040, 1112
PIONEER
1018, 1046, 1055, 1057, 1060,
1091, 1107, 1123, 1124
MD PLAYER
Manufacturer
SONY
KENWOOD
SHARP
ONKYO
ORION
DENON
PIONEER
CD-R
Code
5401
5402,5407
5403
5404
5406
5405
5408
LD PLAYER
Manufacturer
AKAI
BBK
CYRUS
DENON
DISCO VISION
FUNAI
HITACHI
HONG DENG
IDALL
KEBAO
MARANTZ
MITSUBISHI
NAD
PANASONIC
PHILIPS
RADIOLA
ROWA
SALORA
SEGA
SHARP
SHINCO
SMC
SONY
SUPER
TELEFUNKEN
TOSHIBA
PIONEER
DVD
Code
5222
5224
5207
5202
5201
5217
5201
5213
5219
5215
5203, 5205
5202
5202
5210
5203, 5207, 5209
5207
5212
5203
5201
5221
5211
5220
5204, 5206, 5216
5218
5215
5202
5223
5201,5202, 5208
5214
60
CD
CD PLAYER
CD
Manufacturer
Code
AIWA
5016, 5021
AKAI
5014, 5020, 5032
ANAM
5041
ARCAM
5021
AUDIOLAB
5021
AUDIOMECA
5021
AUDIO TON
5021
BESTAR
5022
BURMESTER
5045
CALIFORNIA AUDIO LABS 5004
CARVER
5021, 5025, 5046
CONDOR
5018, 5022
CURTIS MATHES
5004
CYRUS
5021
DENON
5002, 5006, 5040, 5060
DKK
5001
DUAL
5031
DYNAMIC BASS
5025
EMERSON
5038
EROICA
5053, 5054
FANTASIA
5051
FISHER
5024, 5025
GARRARD
5044, 5045
GENEXXA
5005, 5038
GOLDSTAR
5043, 5051
GRUNDIG
5021
HARMAN/KARDON 5021, 5023
HITACHI
5005
INKEL
5015, 5026, 5046
JVC
5011
KENWOOD
5003, 5008, 5029, 5056, 5057,
5062
KRELL
5021
LINN
5021
LUXMAN
5036
LXI
5038
MAGNAVOX
5021, 5038
MARANTZ
5004, 5009, 5017, 5021, 5026
MATSUI
5021
MCS
5004
MEMOREX
5022
MERIDIAN
5021
MICROMEGA
5021
MISSION
5021
MITSUBISHI
5014, 5020
MTC
5045
NAD
5001
NAIM
5021
NIKKO
5024, 5041, 5051
NSM
5021
En
XRB3013A.49.67
60
CD-R
01.12.12, 4:49 PM
Controlling the rest of your system
ONKYO
OPTIMUS
ORION
PANASONIC
PARASOUND
PHILIPS
PMG
POPPY
PROTON
QED
QUAD
QUASAR
RCA
REALISTIC
REVOX
ROTEL
SAE
SANSUI
SANYO
SCHNEIDER
SCOTT
SEARS
SHARP
SHERWOOD
SONY
SOUDESIGN
TASCAM
TEAC
TECHNICS
THORENS
TOSHIBA
UNIVERSUM
YAMAHA
YORX
VICTOR
WARDS
PIONEER
5012, 5013, 5042, 5059
5001, 5005, 5008, 5019, 5025,
5038, 5045, 5046, 5048
5061
5004, 5037
5045
5021, 5055
5022
5022
5021
5021
5021
5004,
5010, 5025, 5038
5025, 5026, 5045
5021
5021, 5045
5021
5021, 5033, 5038
5025, 5039
5018
5038
5038
5008, 5026, 5058
5015, 5026, 5031
5001, 5027, 5050
5019
5045
5024, 5026, 5044, 5045
5004, 5034, 5037
5021
5049
5021
5007, 5028
5047
5011
5010, 5021
5005, 5030, 5035, 5038, 5048,
5052, 5063
TAPE DECK
Manufacturer
ADC
AIWA
AKAI
ANAM
ARCAM
CARVER
DENON
DUAL
CD-R
Code
6013
6002, 6022, 6017, 6018
6015, 6016
6035
6005
6002, 6028
6005, 6039
6037
CD
09
DYNAMIC BASS
EROICA
FISHER
GARRARD
GOLDSTAR
GRUNDIG
HARMON/KARDON
INKEL
JVC
KENWOOD
KYOCERA
LOTTE
LUXMAN
MAGNAVOX
MARANTZ
MEMOREX
MITSUBISHI
NAKAMICHI
NIKKO
OLYMPUS
ONKYO
OPTIMUS
PANASONIC
PHILIPS
RCA
RENAISSANCE
REVOX
SAMSUNG
SANSUI
SANYO
SHARP
SONIC
SONY
TEAC
TECHNICS
THORENS
VICTOR
WARDS
YAMAHA
PIONEER
6028
6041
6028
6036
6036
6002
6002, 6014
6003
6027, 6030, 6031
6003, 6004, 6019, 6024, 6025
6013
6034
6029
6002
6002
6008, 6009
6016
6020
6035
6029
6010, 6011, 6032
6001, 6021
6023
6002
6028
6040
6002
6038
6002
6028
6019
6036
6012, 6026, 6033
6038
6023
6002
6027, 6030
6001
6006, 6007, 6019
6001, 6008, 6009
6021,
DVD PLAYER
Manufacturer
TOSHIBA
SONY
PANASONIC
KENWOOD
JVC
SAMSUNG
AKAI
HARMAN/KARDON
DVD
Code
5302
5306
5301, 5322
5307
5311, 5318
5313
5316
5314
61
En
XRB3013A.49.67
61
01.12.12, 4:49 PM
09
Controlling the rest of your system
MAGNAVOX
MITSUBISHI
ONKYO
PROSCAN
RCA
SHARP
THETA DIGITAL
TECHNICS
THOMSON
YAMAHA
PHILIPS
ZENITH
PIONEER
5302
5303
5302, 5317, 5319
5304
5304
5320
5312
5301
5310
5301, 5309
5302, 5308
5302, 5315
5305, 5312, 5321
5322
AMPLIFIER
Manufacturer
AUDIOLAB
DENON
GRUNDIG
MARANTZ
MICROMEGA
PHILIPS
PIONEER
REVOX
TANDBERG
THORENS
YAMAHA
EROICA
FANTASIA
FERGUSON
FINE ARTS
FISHER
GARRARD
GOLDSTAR
GOODMANS
GP AUDIO
GRUNDIG
HARMAN/KARDON
INKEL
JBL
JVC
KENWOOD
TUN
LOTTE
LUXMAN
MAGNAVOX
MARANTZ
MCINTOSH
MCS
MCSILVER
MICROMEGE
NIKKO
OPTIMUS
ONKYO
PALLADIUM
PANASONIC
PHILIPS
Code
8005
8002
8005
8005
8005
8005
8004
8005
8003
8005
8001, 8006
MISC AUDIO
TUN
Manufacturer
Code
JERROLD
8201, 8203
STARCOM
8201
SCIENTIFIC ATLANTA 8202
62
RECEIVERS
TUN
Manufacturer
ADC
AIWA
AKAI
ANAM
ARCAM
AUDIOLAB
CAPETRONIC
CARVER
CURTIS
DAEWOO
DENON
DUAL
Code
7042
7012, 7023, 7031, 7055, 7064
7011, 7027
7010, 7046
7018, 7048
7059
7042
7055, 7059
7008
7032
7001, 7056, 7058
7040
PHONOTREND
QUASAR
RCA
RENAISSANCE
REVOX
ROADSTAR
SABA
SAISHO
SAMSUNG
SANSUI
SANYO
SCHNEIDER
SHARP
SHERWOOD
SOUNDESIGN
SONY
TAE KWANG
TEAC
TECHNICS
TELEFUNKEN
THORENS
7005
7037
7042
7059
7028
7032, 7034, 7035
7010
7027
7033
7018, 7059
7009, 7051
7038, 7040
7009
7007, 7036, 7042
7003, 7017, 7025, 7026, 7044,
7053, 7063, 7066
7037, 7039
7021
7030, 7042, 7055, 7059
7004, 7018, 7055, 7059
7020
7004
7037
7018, 7059
7032, 7037, 7046
7017, 7034, 7042, 7049, 7052
7013, 7029
7050
7004, 7024, 7041
7018, 7030, 7045, 7048, 7051,
7055, 7059
7038
7004
7006, 7042
7043
7018
7027
7042
7027
7010
7027, 7055
7028
7042
7017
7038
7049
7015, 7054, 7057, 7060
7034
7010, 7035
7004, 7062, 7065
7019, 7024, 7041, 7061, 7062,
7065
7018, 7059
En
XRB3013A.49.67
62
01.12.12, 4:49 PM
Controlling the rest of your system
UHER
VICTOR
WARDS
YAMAHA
PIONEER
7027, 7042, 7050
7007
7002, 7006, 7008
7016, 7017
7002, 7008, 7014, 7022, 7042,
7047, 7050, 7052
VCR
Manufacturer
PHILIPS
PANASONIC
THOMSON
SONY
JVC
GRUNDIG
AKAI
HITACHI
TOSHIBA
MITSUBISHI
SHARP
ORION
SANYO
FERGUSON
BLAUPUNKT
NOKIA
ADMIRAL
ADVENTURA
AIKO
AIWA
AKIBA
ALBA
AMBASSADOR
AMERICA ACTION
AMERICAN HIGH
AMSTRAD
ANAM
ANAM NATIONAL
ANITECH
ASA
ASHA
ASUKA
AUDIOVOX
VCR
Code
2015, 2035, 2074, 2075
2015, 2042, 2053, 2054,
2055, 2087
2021, 2064, 2074
2001, 2009, 2012, 2013, 2014,
2015
2008, 2021, 2033, 2049, 2050,
2074, 2080
2003, 2005, 2007, 2010, 2034,
2035, 2048, 2050, 2054, 2069,
2071, 2075
2021, 2029, 2038, 2060, 2063
2001, 2004, 2021, 2022, 2043,
2056, 2057
2021, 2023, 2024, 2035, 2074
2023, 2027, 2033, 2035, 2045
2027, 2073
2002, 2004, 2016, 2036, 2046,
2052, 2070, 2072, 2078
2025, 2026, 2037, 2057
2021, 2039, 2064, 2065
2003, 2005, 2010, 2014, 2041,
2042, 2048, 2054, 2055, 2075
2025, 2037, 2038, 2057
2027, 2052
2001
2059
2001, 2017, 2062, 2070, 2072
2034
2011, 2034, 2052, 2059, 2063,
2072
2011
2059
2015
2001, 2059, 2067, 2068
2017, 2042, 2054, 2057, 2059,
2082, 2084
2042, 2054, 2087
2034
2017, 2035
2057
2017
2017
09
BAIRD
2001, 2021, 2037, 2039
BASIC LINE
2011, 2034, 2059
BEAUMARK
2057
BELL & HOWELL
2037
BRANDT
2047, 2064, 2065
BRANDT ELECTRONIC 2021
BROKSONIC
2002, 2040, 2046, 2052, 2078
BUSH
2034, 2052, 2059, 2072
CALIX
2017
CANON
2015
CAPEHART
2011
CARVER
2035
CATRON
2011
CCE
2034, 2059
CGE
2001
CIMLINE
2034
CINERAL
2059
CITIZEN
2017, 2059
CLATRONIC
2011
COLT
2034
COMBITECH
2072
CONDOR
2011
CRAIG
2017, 2026, 2034, 2057, 2058
CROWN
2011, 2034, 2059
CURTIS MATHES
2015, 2021, 2032, 2042
CYBERNEX
2057
CYRUS
2035
DAEWOO
2011, 2024, 2025, 2059, 2083
DANSAI
2034
DAYTRON
2011
DECCA
2001, 2035
DE GRAAF
2022, 2043
DENON
2022
DUAL
2021
DUMONT
2001, 2035, 2037
DYNATECH
2001
ELBE
2018
ELCATECH
2034
ELECTROHOME
2017
ELECTROPHONIC 2017
EMEREX
2012
EMERSON
2001, 2002, 2017, 2023, 2040,
2046, 2051, 2052, 2059, 2078,
2083
ESC
2057, 2059
FIDELITY
2001
FINLANDIA
2035, 2037
FINLUX
2001, 2022, 2035, 2037
FIRSTLINE
2017, 2023, 2024, 2034, 2052
FISHER
2025, 2026, 2030, 2037
FRONTECH
2011
FUJI
2015
63
En
XRB3013A.49.67
63
01.12.12, 4:49 PM
09
Controlling the rest of your system
FUNAI
2001
GARRARD
2001
GE
2015, 2027, 2032, 2057
GEC
2035
GENERAL
2011, 2028
GOLDHAND
2034
GOLDSTAR
2017, 2018, 2053, 2079
GOODMANS
2001, 2017, 2034, 2059, 2075
GO VIDEO
2077, 2081
GRAETZ
2005, 2021, 2037, 2057
GRANADA
2025, 2035, 2037
GRADIENTE
2001, 2008
GRANDIN
2001, 2017, 2034
HANSEATIC
2017
HARMAN/KARDON 2018, 2035
HARLEY DAVIDSON 2001
HARWOOD
2034
HCM
2034
HEADQUARTER
2025
HINARI
2004, 2034, 2057, 2072
HI-Q
2026
HUGHES NETWORK SYSTEMS 2022
HYPSON
2034
IMPERIAL
2001
INGERSOL
2004
INTERFUNK
2035
ITT
2005, 2021, 2025, 2037, 2038,
2057, 2074
ITV
2017, 2059
JENSEN
2021
KAISUI
2034
KEC
2017, 2059
KENDO
2038, 2052
KENWOOD
2018, 2021, 2033
KLH
2034
KODAK
2015, 2017
KORPEL
2034
LAYCO
2034
LENCO
2059
LG
2079
LLOYD’S
2001, 2051
LOEWE
2004, 2005, 2017, 2035
LOGIK
2004, 2034, 2057
LUXOR
2023, 2025, 2027, 2037, 2038
LXI
2017
M ELECTRONIC
2001
MAGNASONIC
2059
MAGNAVOX
2001, 2015, 2019, 2035
MAGNIN
2057
MANESTH
2024, 2034
MARANTZ
2003, 2005, 2015, 2035
MARTA
2017
MATSUI
2004, 2016, 2036, 2052, 2070,
2072
MATSUSHITA
2015, 2042, 2055
MEI
2015
MELECTRONIC
2018
MEMOREX
2001, 2015, 2017, 2019, 2025,
2026, 2027, 2037, 2052, 2057,
2062, 2085, 2087, 2088
MEMPHIS
2034
METZ
2003, 2005, 2017, 2042, 2048,
2055, 2069
MGA
2023, 2057
MGN TECHNOLOGY 2057
MINCRVA
2048
MINERVA
2005, 2010, 2048
MINOLTA
2022
MOTOROLA
2015, 2027
MTC
2001, 2057
MULTITECH
2001, 2034
MURPHY
2001
NAD
2031
NATIONAL
2054
NEC
2018, 2020, 2021, 2033, 2037
NECKERMANN
2035
NESCO
2034
NIKKO
2017
NIKON
2014
NOBLEX
2057
NOKIA
2021, 2025, 2037, 2038, 2057
NORDMENDE
2021, 2061, 2064, 2065, 2074
OCEANIC
2001, 2021
OKANO
2063, 2070
OLYMPUS
2015, 2054
OPTIMUS
2017, 2027, 2031, 2037, 2042,
2077, 2086, 2087, 2088
OSAKI
2001, 2017, 2034
OTTO VERSAND
2035
PALLADIUM
2005, 2017, 2021, 2034
PATHE MARCONI 2021
PATHE CINEMA
2016
PENTAX
2022
PENNY
2015, 2017, 2018, 2020, 2022,
2057
PERDIO
2001
PHILCO
2015, 2018, 2052, 2078
PHONOLA
2035
PILOT
2017
PORTLAND
2011
PROFEX
2066
PROFITRONIC
2057
PROLINE
2001
PROSCAN
2032
64
En
XRB3013A.49.67
64
01.12.12, 4:49 PM
Controlling the rest of your system
PROTEC
PULSAR
PYE
QUARTER
QUARTZ
QUASAR
QUELLE
RADIO SHACK
RADIOLA
RADIX
RANDEX
RCA
REALISTIC
REX
RFT
RICOH
ROADSTAR
RUNCO
SABA
SAISHO
SALORA
SANKY
SANSUI
SAMSUNG
SAVILLE
SBR
SCHAUB LORENZ
SCHNEIDER
SCOTT
SEARS
SEG
SEI
SELECO
SEMP
SENTRA
SHINTOM
SHOGUN
SHORAI
SIEMENS
2017, 2030, 2035
SILVA
SINGER
SINUDYNE
SOLAVOX
SONOLOR
SONTEC
STS
SUNKAI
2034
2019
2035
2025
2025
2015, 2042, 2087
2035
2001, 2085
2035
2017
2017
2015, 2022, 2027, 2032, 2038,
2057
2001, 2015, 2017, 2025, 2026,
2027, 2037
2021, 2074
2075
2014
2017, 2034, 2057, 2059
2019
2021, 2049, 2050, 2061, 2064,
2065, 2074
2004, 2016, 2036, 2052
2023, 2025, 2038
2019, 2027
2001, 2021, 2033, 2052, 2058,
2078
2024, 2057, 2076, 2077
2072
2035
2001, 2005, 2021, 2037
2001, 2034, 2035
2023, 2024, 2040, 2046
2001, 2015, 2017, 2022, 2025,
2026, 2037
2057, 2066
2004, 2035
2021
2024
2011
2034, 2037
2057
2004
2003, 2005, 2010
2037, 2048
2017
2024, 2034
2004, 2035
2011
2025
2017
2022
2070
09
SUNSTAR
SUNTRONIC
SYLVANIA
SYMHONIC
TASHIKO
TATUNG
TEAC
TEC
TECHNICS
TEKNIKA
TELEAVIA
TELEFUNKEN
TENOSAL
TENSAI
THOMAS
THORN
TMK
TOTEVISION
TOWADA
UHER
UNITECH
UNIVERSUM
2001
2001
2001, 2015, 2023, 2035
2001
2001
2001, 2021, 2035
2001, 2021
2011
2015, 2042, 2054
2001, 2015, 2007, 2017, 2028
2021
2021, 2047, 2058, 2064, 2074
2034
2001, 2066
2001
2016, 2021, 2037
2051, 2057
2017, 2057
2066
2057
2057
2001, 2006, 2010, 2017, 2035,
2038, 2048, 2057, 2067
VECTOR
2024
VECTOR RESEARCH 2018, 2020
VICTOR
2008, 2021, 2033
VIDEO CONCEPTS 2020, 2024
VIDEOSONIC
2057
WARDS
2001, 2015, 2022, 2026, 2027,
2032, 2034, 2035, 2057
WHITE WESTINGHOUSE 2052, 2059
XR-1000
2001
XR-1001
2015
XR-1002
2034
YAMAHA
2018
YAMISHI
2034
YOKAN
2034
YOKO
2011, 2057
ZENITH
2001, 2014, 2019, 2052, 2078
PIONEER
2031, 2033, 2035, 2044, 2056
SATELLITE TUNER
Manufacturer
ABSAT
AST
ALBA
ALDES
AMSTRAD
ANKARO
ANTTRON
TV
TVC
Code
4006
4027
4029, 4034, 4037, 4052
4019
4003, 4016, 4025, 4038, 4039,
4042
4013, 4019, 4030, 4044
4009, 4034
65
En
XRB3013A.49.67
65
01.12.12, 4:49 PM
09
66
Controlling the rest of your system
ARMSTRONG
4015
ASTRA
4005
ASTRO
4008, 4039, 4045
AVALON
4031
AXIS
4030, 4046
BT
4053
BEKO
4010
BEST
4030
BLAUPUNKT
4008
BOCA
4015, 4043
BRAIN WAVE
4022
BRITISH SKY BROADCASTING 4058
BUSH
4002
CNT
4045
CAMBRIDGE
4024
CANAL SATELLITE 4059
CANAL+
4059
CHANNEL MASTER 4029
COMLINK
4019
CONNEXIONS
4031
CROWN
4015
CYRUS
4011
D-BOX
4054
DDC
4029
DNT
4011, 4031
ECHOSTAR
4031, 4036, 4061
EMANON
4034
FTE HUMAX
4060
FERGUSON
4002, 4009, 4010, 4023
FIDELITY
4016
FINLUX
4005, 4024, 4032, 4037
FRACARRO
4061
FREECOM
4034
FUBE
4030, 4031, 4034
G-SAT
4009
GALAXIS
4019, 4057, 4060
GENERAL INSTRUMENT 4012
GOLD BOX
4059
GOODING
4048
GOODMANS
4010
GRUNDIG
4008, 4010, 4048
HINARI
4009
HIRSCHMANN
4008, 4032, 4039, 4040, 4049
HITACHI
4037
HOUSTON
4053
HUTH
4013, 4015, 4019, 4026
ITT
4005
INVIDEO
4061
INTERVISION
4050
JVC
4048
JOHANSSON
4022
KATHREIN
4004, 4006, 4008, 4011, 4035,
4041
KREISELMEYER
KYOSTAR
LA SAT
LENCO
LENNOX
LUPUS
LUXOR
MANHATTAN
MARANTZ
MASPRO
MATSUI
MEDIASAT
MEDIAMARKT
MINERVA
MORGAN’S
NAVEX
NEUHAUS
NEUSAT
NEWHAUS
NIKKO
NOKIA
NORDMENDE
ORBITECH
OXFORD
PACE
PALLADIUM
PALSAT
PANDA
PHILIPS
PHONOTREND
PIONEER
PLANET
PROMAX
PROSAT
QUADRAL
RADIOLA
RADIX
RFT
SAT
SABA
SABRE
SAGEM
SALORA
SATCOM
SATEC
SATMASTER
SATPARTNER
SCHWAIGER
SEEMANN
4008
4034
4043, 4045
4034
4050
4030
4005, 4049
4037, 4045, 4050
4011
4004, 4023
4024, 4048
4059
4015
4048
4015, 4043
4022
4039
4057
4013
4028
4005, 4032, 4037, 4049, 4054,
4063
4029
4039
4024
4002, 4009, 4014, 4023, 4037,
4055, 4058
4048
4039
4037
4007, 4011, 4020, 4037, 4048,
4059
4019, 4050
4021, 4059
4061
4037
4019
4029, 4044
4011
4031, 4064
4011, 4013, 4019
4027, 4038
4023, 4045
4037
4056
4005
4026, 4051
4009
4026
4022, 4034, 4040, 4045
4009, 4041
4031, 4046
En
XRB3013A.49.67
66
01.12.12, 4:49 PM
Controlling the rest of your system
SEG
SIEMENS
SKYMASTER
SONY
STRONG
SUNSTAR
TPS
TANTEC
TECHNISAT
TECHNILAND
TELEFUNKEN
TELEKA
TELESAT
THOMSON
TONNA
TRIAD
TRIASAT
UNITOR
UNIVERSUM
VENTANA
VORTEC
VTECH
WINERSAT
WISI
XSAT
XCOM MULTIMEDIA
ZEHNDER
4030, 4034
4008
4019, 4044, 4051
4017, 4018
4062
4043
4056
4023, 4037
4001, 4039
4026
4034
4015, 4052
4051
4037, 4059
4026, 4053
4027
4040
4022
4008, 4049
4011
4034
4027
4022
4008, 4027, 4031, 4037
4006, 4065
4065
4033, 4045, 4047
CABLE TV
TV
09
JASCO
JERROLD
TVC
Manufacturer
Code
ABC
3002, 3003, 3004, 3006, 3008
ANDOVER
3037
BELL & HOWELL
3006
BIRGMINGHAM CABLE
COMMUNICATION 3020
BRITISH TELECOM 3002, 3012
CABLETIME
3016, 3019, 3025, 3029
CONTEC
3009
CLYDE
3011
CRYPTOVISION
3038
DAEHAN
3043
DAERYUNG
3003
DECSAT
3027
EVERQUESST
3007
FILMNET
3028
FRANCE TELECOM 3030
GEC
3011
GEMINI
3007
GENERAL INSTRUMENT 3004, 3020, 3031, 3046
GOLDSTAR
3014, 3047
GRUNDIG
3035
HITACHI
3004
3007
3002, 3004, 3005, 3006, 3007,
3020, 3031, 3046
3044
3001
3009, 3028
3041
3009
3039
3001, 3013
3001
3001
LG ALPS
MEMOREX
MNET
NOW
OAK
PACIFIC
PANASONIC
PARAGON
PULSAR
PVP STEREO VISUAL
MATRIX
3002
PIONEER
3010, 3014, 3018, 3036
QUASAR
3001
RADIO SHACK
3007
REMBRANDT
3004
RUNCO
3001
SAMSUNG
3014, 3040
SATBOX
3024
SIGNAL
3007
SIGNATURE
3004
STS
3015
SALORA
3026
SCIENTIFIC
3003, 3032, 3049
SCIENTIFIC ATLANTA 3003, 3008, 3021
SEAWOO
3045
STARCOM
3002, 3007
STARGATE
3007
STARQUEST
3007
TAIHAN
3043
TELESERVICE
3022
TELE+1
3028
TUDI
3023
TUSA
3007
TOCOM
3005
TONGKOOK
3042, 3048
TOSHIBA
3001
UNITED CABLE
3002
VIDEOWAY
3017
VISICABLE+
3033
WESTMINSTER
3012
WOLSEY GENE
3037
ZENITH
3001, 3034
67
En
XRB3013A.49.67
67
01.12.12, 4:49 PM
10
Additional information
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Investigate the other components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer
authorized service center or your dealer to carry out repair work.
Problem
Remedy
The power does not turn on.
• Connect the power plug to the wall outlet.
• Disconnect the power plug from the outlet, and insert again.
• Make sure there are no loose strands of speaker wire touching
the rear panel. This could cause the receiver to shut off
automatically.
No sound is output when a
function is selected.
• Make sure the component is connected correctly (refer to
pages 14–19).
• Press MUTE on the remote control to turn muting off.
• Adjust the MASTER VOLUME.
• Press the MONITOR button to turn monitoring off.
No image is output when a
function is selected.
• Make sure the component is connected correctly (refer to
pages pages 14–19).
• Select the correct component (use the MULTI JOG/INPUT
SELECTOR dial or the MULTI CONTROL buttons on the remote).
Considerable noise in radio
broadcasts.
• Tune in the correct frequency.
• Connect the antenna (refer to page 19).
• Route 2 RF and digital cables away from the antenna
terminals and wires.
• Fully extend the FM wire antenna, position for best reception,
and secure to a wall.
• Connect an outdoor FM antenna (refer to page 19).
• Adjust the direction and position for best reception.
• Connect an additional internal or external AM antenna (refer
to page 19).
• Turn off the equipment causing the noise or move it away from
the receiver.
• Place the antenna farther away from the equipment causing
the noise.
Broadcast stations cannot be
selected automatically.
• Connect an outdoor antenna (refer to page 19).
68
En
XRB3013A.68.74
68
01.12.12, 5:13 PM
Additional information
10
Problem
Remedy
No sound from surround or
center speakers.
• Refer to Speaker setting on page 39 to check the speaker
settings.
• Refer to Setting the relative volume level of each channel on
page 44 to check the speaker levels.
• Connect the speakers properly (refer to page 19–21).
No sound from surround back
speakers.
• Refer to Surround back speaker setting on page 40 to check
the surround back speaker settings.
• Refer to the table on page 33 to make sure the 6.1 channel
setting and the sound mode are set for surround back sound.
Noise during playback of a
cassette deck.
• Move the cassette deck further from your receiver, until the
noise disappears.
Sound is produced from other
components, but not from LD or
DVD player.
• Set the SIGNAL SELECT to AUTO, DIGITAL or ANALOG
according to the type of connections made. (refer to page 34).
• Set the digital input settings correctly (refer to page 43).
• Make digital connections (refer to page 14) and set the
SIGNAL SELECT to DIGITAL (refer to page 34).
• Refer to the instruction manual supplied with the DVD player.
No sound is output or a noise is
output when software with DTS
is played back.
• Set the digital volume level of the player to full, or to the
neutral position.
When a search is performed by • This is not a malfunction, but be sure to turn the volume
a DTS compatible CD player
down to prevent the output of loud noise from your speakers.
during playback, noise is output.
Can’t operate the remote
control.
• Replace the batteries (refer to page 6).
• Operate within 23 feet ( 7 m), 30° of the remote sensor on the
front panel (refer to page 6).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct
light.
The display is dark or off.
• Press FL DIMMER on the remote control repeatedly to return
to the default.
If the unit does not operate normally due to external effects such as static electricity disconnect the
power plug from the outlet and insert again to return to normal operating conditions.
69
En
XRB3013A.68.74
69
01.12.12, 5:13 PM
10
Additional information
Specifications
Video Section
Amplifier Section
Input (Sensitivity/Impedance)
VCR/DVR, DVD/LD, TV/SAT ............. 1 Vp-p/75 Ω
Continuous average power output of 100 watts*
per channel, min., at 8 ohms, from 20 Hz to
20,000 Hz with no more than 0.2 %** total
harmonic distortion (front).
Continuous Power Output
Front ...................................... 100 W per channel
(1kHz, 1.0 %, 8 Ω)
Center .......................... 100 W (1kHz, 1.0 %, 8 Ω)
Surround ............................... 100 W per channel
(1kHz, 1.0 %, 8 Ω)
Surround Back* ................... 100 W per channel
(1kHz, 1.0 %, 8 Ω)
* VSX-D811S only
Input (Sensitivity/Impedance)
CD, VCR/DVR, CD-R/TAPE/MD,
DVD/LD, TV/SAT ........................... 200 mV/47 kΩ
Frequency Response
CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD,
TV/SAT ........................... 5 Hz to 100,000 Hz +0
– 3 dB
Output (Level/Impedance)
VCR/DVR REC, CD-R/TAPE/
MD REC ....................................... 200 mV/2.2 kΩ
Tone Control
BASS .......................................... ± 6 dB (100 Hz)
TREBLE ...................................... ± 6 dB (10 kHz)
LOUDNESS .................................. +9 dB/+9 dB
(100 Hz/10 kHz)
Signal-to-Noise Ratio (IHF, short
circuited, A network)
CD, VCR/DVR, CD-R/TAPE/MD,
DVD/LD, TV/SAT ......................................... 96 dB
Output (Level/Impedance)
VCR/DVR ........................................... 1 Vp-p/75 Ω
Frequency Response
VCR/DVR, DVD/LD,
TV/SAT ] MONITOR ........... 5 Hz to 7 MHz +0
– 3 dB
Signal-to-Noise Ratio ................................. 55 dB
Cross Talk .................................................... 55 dB
FM Tuner Section
Frequency Range ............. 87.5 MHz to 108 MHz
Usable Sensitivity ................ Mono:13.2 dBf, IHF
(1.3 µV/ 75 Ω)
50 dB Quieting Sensitivity .......... Mono: 20.2 dB
Stereo: 38.6 dBf
Signal-to-Noise Ratio ..................... Mono: 73 dB
(at 85 dBf)
Stereo: 70 dB (at 85 dBf)
Distortion ........................... Stereo: 0.5 % (1 kHz)
Alternate Channel Selectivity .................... 60 dB
(400 kHz)
Stereo Separation ......................... 40 dB (1 kHz)
Frequency Response .................. 30 Hz to 15 kHz
(±1 dB)
Antenna Input (DIN) .............. 75 Ω unbalanced
AM Tuner Section
Frequency Range .............. 530 kHz to 1,700 kHz
Sensitivity (IHF, Loop antenna) ............ 350 µV/m
Selectivity .................................................... 25 dB
Signal-to-Noise Ratio ................................. 50 dB
Antenna ........................................ Loop antenna
Signal-to Noise Ratio [EIA, at 1 W (1
kHz)]
CD, VCR/DVR, CD-R/TAPE/MD,
DVD/LD, TV/SAT ......................................... 79 dB
70
En
XRB3013A.68.74
70
01.12.12, 5:13 PM
Additional information
10
Miscellaneous
Power Requirements ................. AC 120 V, 60Hz
Power Consumption
VSX-D711 .................................. 260W, 340 VA
VSX-D811S ............................... 300W, 420 VA
In Standby ................................................ 1 W
AC Outlet .................. 100 W MAX. (SWITCHED)
Dimensions ..... 420 (W) x 158 (H) x 401 (D) mm
(16-9/16 (W) x 6-4/16 (H) x 15-6/16 (D) in.)
Weight (without package)
VSX-D711 .................................................... 9.0 kg
(19.8 lb)
VSX-D811S ................................................ 10.5 kg
(23.2 lb)
Furnished Parts
AM loop antenna ................................................ 1
FM wire antenna ................................................ 1
Dry cell batteries (AA size IEC R6P) ................. 2
Remote control ................................................... 1
Operating instructions ...................................... 1
Specifications and the design are subject to
possible modifications without notice, due to
improvements.
* Measured pursuant to the Federal Trade
Commission’s Trade Regulation rule on Power
Output Claims for Amplifiers.
** Measured by Audio Spectrum Analyzer.
71
En
XRB3013A.68.74
71
01.12.12, 5:13 PM
Additional information
NI
C IND
U
S
SO
CIAT
N
•A
EST 1924
•
EIA
RIES
ELECT
O
ST
R
10
IO
We
Want You
LISTENING
For A Lifetime
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your musical enjoyment. Now
it’s time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the
Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing
it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion-and, most
importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to higher volumes of sound. So what sounds
“normal” can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level
BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future. After all, we want you listening
for a lifetime.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing damage from
loud noise is often undetectable until it is too late, this manufacturer and the Electronic Industries Association’s Consumer
Electronics Group recommend you avoid prolonged exposure to excessive noise. This list of sound levels is included for
your protection.
Decibel
Level
30
40
50
60
70
80
Example
Quiet library, soft whispers
Living room, refrigerator, bedroom away from traffic
Light traffic, normal conversation, quiet office
Air conditioner at 20 feet, sewing machine
Vacuum cleaner, hair dryer, noisy restaurant
Average city traffic, garbage disposals, alarm clock
at two feet.
THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE
90
100
120
140
180
Subway, motorcycle, truck traffic, lawn mower
Garbage truck, chain saw, pneumatic drill
Rock band concert in front of speakers, thunderclap
Gunshot blast, jet plane
Rocket launching pad
NI
C IND
U
SO
CIAT
•
•A
S
EST 1924
N
EIA
RIES
ELECT
O
ST
R
Information courtesy of the Deafness Research Foundation.
We
Want You
IO
LISTENING
For A Lifetime
72
En
XRB3013A.68.74
72
01.12.12, 5:13 PM
Additional information
10
73
En
XRB3013A.68.74
73
01.12.12, 5:13 PM
10
Additional information
74
En
XRB3013A.68.74
74
01.12.12, 5:13 PM
Additional information
10
75
En
XRB3013A.68.74
75
01.12.12, 5:13 PM
Should this product require service in the U.S.A. and you wish to locate the nearest Pioneer
Authorized Independent Service Company, or if you wish to purchase replacement parts,
operating instructions, service manuals, or accessories, please call the number shown below.
800–421–1404
Please do not ship your product to Pioneer without first calling the Customer Service Department
at the above listed number for assistance.
PIONEER ELECTRONICS (USA) INC.
CUSTOMER SERVICE DEPARTMENT
P.O. BOX 1760, LONG BEACH,
CA 90801-1760, U.S.A.
For warranty information please see the Limited Warranty sheet included with your product.
Should this product require service in Canada, please contact a Pioneer Canadian Authorized
Dealer to locate the nearest Pioneer Authorized Service Company in Canada.
Alternatively, please contact the Customer Service Department at the following address:
Pioneer Electronics of Canada, Inc.
Customer Service Department
300 Allstate Parkway, Markham, Ontario L3R OP2
(905) 479-4411
1-877-283-5901
For warranty information please see the Limited Warranty sheet included with your product.
Si ce produit doit être réparé au Canada, veuillez vous adresser à un distributeur autorisée
Pioneer au Canada pour obtenir le nom de la Société de Service Autorisée Pioneer le plus près de
chez vous. Ou encore, veuillez vous communiquer avec le Service de Clientèle de Pioneer:
Pioneer électroniques du Canada, Inc.
Département de service au consommateurs
300 Allstate Parkway, Markham, Ontario L3R OP2
(905) 479-4411
1-877-283-5901
Pour obtenir des renseignements sur la garantie, veuillez vous reporter au feuillet sur la Garantie
Limitée gui accompagne le produit.
Published by Pioneer Corporation.
Copyright © 2001 Pioneer Corporation.
All rights reserved.
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS [USA] INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A.
PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: [03] 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
San Lorenzo 1009 3er Piso Desp. 302 Col. Del Valle Mexico D.F. C.P. 03100
TEL: 55-5688-5290
<TNGZF/01L00001>
XRB3013A.68.74
Printed in
76
<XRB3013-A>
01.12.12, 5:13 PM