Emerson HD13003 Owner`s manual

HD1300 3 US manual
11/14/00
1:40 PM
Page 1
CAUTION: Read all instructions carefully before installation.
Save this Owner’s Manual for future reference.
Model No.
HD1300 3
EMERSON
®
MoistAIR™ HD1300
Evaporative Console
Humidifier Owner’s Manual
Part No. SP6305
Printed in Canada
HD1300 3 US manual
11/14/00
1:40 PM
Page 2
Limited Warranty
All products covered by this Owner’s Manual are warranted against defects in
workmanship and materials for one year from the date of sale except for motors,
which are warranted for two years. This warranty does not apply to damage from
accident, misuse or alteration nor where the connected voltage is more than 5%
above the nameplate voltage, nor to the equipment improperly installed or wired or
maintained in violation of this Owner’s Manual. No other written or oral warranty
applies. No employee, agent, dealer or other person is authorized to give any warranties on behalf of Emerson Electric.
The customer shall be responsible for all costs incurred in the removal or reinstallation and shipping of the product for repairs. Within the limitations of this warranty,
inoperative units should be returned, freight prepaid to the nearest Emerson authorized service centre, or the Emerson Electric Co. Service Centre, and we will repair
or replace, at our option, at no charge to you with return freight paid by Emerson. It
is agreed that such repair or replacement is the exclusive remedy available from
Emerson Electric Co. and that Emerson Is Not Responsible For Damages Of
Any Kind, Including Incidental And Consequential Damage. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the
above exclusion or limitation may not apply to you.
The warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
For the address of your nearest authorized service centre, call (901) 642-1120.
GENERAL SAFETY INSTRUCTIONS
4. Keep the humidifier clean.
5. Do not put foreign objects inside the
humidifier.
6. Never use your humidifier while any part
is missing or damaged in any manner.
7. To reduce the risk of electrical hazard or
damage to humidifier, do not tilt, jolt or tip
humidifier over while unit is running.
8. To reduce the risk of damage to humidifier, unplug humidifier when water bottles
are empty or when the humidifier is not in
use.
9. To reduce the risk of accidental electrical
shock, do not touch the cord or controls with
wet hands.
10. Note the warning label shown below.
Safety Signal Words
DANGER: means if the safety information is
not followed someone will be seriously
injured or killed.
WARNING: means if the safety information is
not followed someone could be seriously
injured or killed.
CAUTION: means if the safety information is
not followed someone may be injured.
1. To reduce the risk of fire or shock hazard,
plug humidifier directly into a 120V, A.C.
electrical outlet. Do not use extension
cords.
2. Keep the electric cord out of traffic areas.
To reduce the risk of fire hazard, never
put the electric cord under rugs, near heat
registers, radiators, stoves or heaters.
3. Always unplug the humidifier before moving it, removing the fan assembly section,
before cleaning, or whenever the humidifier is not in service.
WARNING: To reduce the risk of fire, electric
shock, or injury always unplug before filling,
servicing or cleaning.
2
HD1300 3 US manual
11/14/00
1:40 PM
Page 3
Know Your Humidifier
Control Panel Cover & Pivoting Lid
Removed for Clarity
Fan Assembly
Controls
Bottles
Fill Light
Filter
Housing
Filters:
Replacement
No. HDC-12
Description
HD1300
Litre Output/24 hrs.
Capacity of Bottles
* Sq. Ft. Coverage
Fan SpeedsVariable
Filters
Fill Light
Auto Humidistat
Auto Shut Off
Dry Out
Controls
CUL Listed
AHAM Certified
Volts
Hertz
Amps
Watts
13
2-3/8 Gallons Each
2,700
4 (HDC-12)
Yes
Yes
Yes
Manual
Rotary
Yes
Yes
120 A.C.
60
2.88
165
* Based on an area with average insulation and an 8
foot ceiling.
3
HD1300 3 US manual
11/14/00
1:40 PM
Page 4
Humidifier Operations
Humidified Air is
Then Released
Through the Top
Your new Emerson humidifier is designed to
satisfy home humidity requirements through the
principle of evaporation of water into the air.
After water is added to the bottles and positioned in the humidifier, the filters begin to
soak up the water and become totally saturated in approximately 30 minutes. Air is drawn
in from the rear of the humidifier and through
the filters by means of two circulation fans. As
air passes through the filters, moisture is
absorbed into the air and then released
through the top of the humidifier. This moist air
is released in the form of vapor. No water
droplets will enter the home. All evaporation
into the air takes place in the humidifier, which
means that the residue left by evaporating
water is not passed into the home, but
remains in the filter.
Dry Air Enters
Through the
Rear
CAUTION: Keep your humidifier clean.
While humidifiers do not cause colds,
some studies suggest that dirty humidifiers can cause cold-like symptoms in
some people. To avoid this, clean your
humidifier weekly with cleaners specifically recommended for humidifiers and
use Emerson WT-BC EPA recommended bacteriostat.
CAUTION: Emerson WT-BC EPA
Registered Bacteriostat available from
your local retail store or call (800) 6543545 to order. Under no circumstances
should you use water treatment products for Roto belt or Ultrasonic humidifiers.
Assembly
Your new Emerson humidifier is completely
assembled for you to use. Remove the packaging material from inside your humidifier
and follow the instructions of this owner’s
manual for proper usage. The packaging
material is located under the fan assembly.
Remove the packaging material and discard.
Electrical Hook-Up
Locate nearest 120V A.C. wall socket in the
location desired, preferably on inside wall.
Plug in the electrical cord.
WARNING: To reduce the risk of fire or
shock hazard, humidifier should be
plugged into a 120V A.C. outlet. Do not
use extension cords.
4
HD1300 3 US manual
11/14/00
1:40 PM
Page 5
Location Instructions
appropriate the unit should be repositioned in
another location.
NOTE: Due to release of cool, moist air from
humidifier, it is best to direct air away from
home thermostat and hot air registers. It is
best to position humidifier next to an inside
wall. Hot air registers and cold air from outside walls can affect the efficiencies of the
controls. Unit should not be placed where
warm air from a hot air register blows directly
on unit.
Step 2
The humidifier should be positioned with the
back (cord exit side), at least 2 inches away
from the wall. Air needs to enter through louvers in the back of the cabinet in order for the
humidifier to operate at peak efficiency.
WARNING: For your own safety, do not
use humidifier if any parts are damaged
or missing.
Step 1
Place humidifier on a flat level surface in area
of house where most humidity is needed, or
one which would likely result in moist air
being circulated throughout the house such
as near a cold air return. Placing the unit
level is very important if the humidifier is
located on carpeting.
NOTE: The 13 gallon humidifier contains
water bottles. The weight of the bottles in
the front of the cabinet may sink the front
casters deeper in the carpet. This will
keep the water level forward in the cabinet. The water level float (located at the
rear of the cabinet) may not sense the
water and the fill light will be on and the
unit will not energize. If this happens, the
unit will need to be leveled in order for the
humidifier to be energized.
NOTE: It may be necessary to purchase leveling coasters from your local hardware store.
The coasters should be positioned under the
front two casters of the humidifier.
Moist air (humidity) produced will disperse
into the whole house, but area closest to unit
will have the highest humidity. If the unit is
positioned close to a window, condensation
may form on the window pane. If this is not
At Least
2" From Wall
Water Fill
Fan Assembly
WARNING: To reduce the risk of shock,
always unplug humidifier before filling,
cleaning, or servicing.
WARNING: To reduce the risk of fire or
shock hazard, do not pour or spill water
into control or motor area. Close the
control cover. If controls get wet, let
them dry completely and have unit
checked by authorized service personnel before plugging in.
This humidifier is designed to be used with
the two water bottles that are located under
the pivoting lid.
Pivoting Lid
Removed for
Clarity
Water
Bottles
Cabinet
5
Front of Humidifier
HD1300 3 US manual
11/14/00
1:40 PM
Page 6
Water Fill (continued)
Open the pivoting lid of the humidifier.
Remove the water bottles, by lifting them
straight up and out of the cabinet.
Notice the water bottles are designed as right
and left hand units. Position them in the correct location so the humidifier can function
properly. The water bottles should rest in the
front of the cabinet. Each “E-Z-Fill Side-Cap”
must be facing the rear of the unit
Each water bottle is designed with an “E-ZFill Side-Cap” that is easily removable.
Remove the “E-Z-Fill Side-Cap” on the side
of the water bottle by twisting counterclockwise.
Place the opening of the water bottle under a
water faucet (the bottle should fit under a
four-inch clearance faucet). Fill with recommended mixture of cold water and if necessary Emerson WT-BC Bacteriostat only. Do
not add solid debris as this could make the
valve leak. Install the “E-Z-Fill Side-Cap” by
twisting clockwise. Hand tighten only.
Check for possible leaks by performing
the following:
1. Grasp bottle handle and hold the bottle
upright over a sink.
2. Press up on valve cap plunger for about
one second to let out a little water.
3. Release the plunger.
4. Listen for air bubbles. Look for leaks
around “E-Z-Fill Side-Cap”.
5. If you hear air bubbles or see leaks,
retighten “E-Z-Fill Side-Cap” and repeat
steps 1-4.
NOTE: Repeat for other bottle. If either fill
cap leaks, water may overflow and leak
out of the rear vents of the cabinet.
Wipe off excess water from the bottle.
Position the water bottle back into the unit.
Grasp the water bottle handle, and lower into
the cabinet until the bottle sits on pads at bottom of cabinet. The “E-Z-Fill Side-Cap” must
be facing the rear of the cabinet. When positioned properly, the plunger will open and
water will flow into the cabinet. The water
level will automatically remain at approximately 1/2" until the bottles are empty.
The unit is now ready for operation.
6
Rear of
Humidifier
“E-Z-Fill Side-Cap” Should Always
Face Rear
Turn Counterclockwise
to Remove Cap
Valve
Cap Plunger
Pivoting Lid Removed
for Clarity
HD1300 3 US manual
11/14/00
1:40 PM
Page 7
Operating Humidifier Controls
The operating controls of your Emerson
evaporative humidifier are located on the top
centre of the humidifier. The controls are
found under the smoked cover, located
between the air circulating fans. Lift the control cover by placing your finger in the round
cutout and lifting. The cover will stay open.
Now you can clearly see the control area.
Familiarize yourself with the controls and reference the diagram of the control area for
the correct naming used within this manual.
To Operate the Controls
Humidity Control:
Adjust the amount of humidity depending on
your needs. The humidifier will turn on and off
as required to maintain level of humidity
selected. A medium setting (half way
between MIN and MAX) is recommended, but
there are times when a low or high amount of
humidity may be preferred. For constant
operation of humidifier, MAX allows for the
maximum amount of humidity to be evaporated into the air continuously.
IMPORTANT: Water damage may result if
condensation starts to form on windows or
walls. Humidity Control setting should be lowered until condensation no longer forms.
Fan Control
Your Emerson humidifier allows a choice to
be made for single or dual fan control. The
slide switch located closest to the front of the
cabinet allows one or two fans to be used.
Slide the switch to the “1” position to operate
one fan and the “2” position to operate both
fans.
The “FAN” slide switch, positioned in the #1
position will operate the humidifier with one
fan only in any speed position and provides
reduced output at a lower noise level. The
“FAN” slide switch positioned in the #2 setting will operate the humidifier with both fans
and provides greater output than the single
fan settings. Maximum output is provided by
the humidifier in the #2 position with the
speed control set at high. This combination of
infinite number of fan/speed settings allows
you to determine the noise level and output
level that best suits you.
HUMIDITY
MIN
Air Flow Control
MAX
The unit is adjusted from “OFF” to high to low
with a variable speed control.
The higher the air flow speed, the more water
is evaporated and released into the air. MIN
speed is the quietest and is provided for conditions that may not require as high an evaporation rate.
MAX
OFF
AIR FLOW
MIN
Fill Light
When the unit has a small amount of water
left in it, the fill light will come on and the unit
will automatically shut off.
FILL
7
FAN
HD1300 3 US manual
11/14/00
1:40 PM
Page 8
Using Your Humidifier
Step 1
Be sure unit is full of water and plugged in.
Step 2
Set the Fan selection switch to “2”. This will
allow both fans to operate if the humidistat
senses humidity is needed.
Step 3
Set air flow control to desired setting.
Step 4
Set Humidity Control to medium position (half
way between MIN and MAX.)
NOTE: Humidifier should operate with humidity control on the recommended medium setting. If it does not, the humidity is at a relatively high level. To test the unit under this
condition, turn Humidity Control all the way to
MAX and unit should begin to operate. After
the unit has been tested, set Humidity Control
to medium or desired level.
Step 5
If humidifier stops running and the Fill Light is
not illuminated, the humidity level is at the
normal requirements for that setting or it is
adjusting to the home conditions. The table
below shows recommended indoor humidity
levels. The figure below shows approximate
relative humidity percentages which correspond to the various settings of the Humidity
Control.
When Outdoor Recommended Indoor
Temperature is: Relative Humidity is:
-10°F
0°F
10°F
20°F & above
20%
25%
30%
35%
um
Rel. H idity
IMPORTANT: Water damage may result if
condensation starts to form on windows
or walls. Humidity Control setting should
be lowered until condensation no longer
forms.
MIN
MAX
Rel. Humid
ity
If humidity level in home is sufficient, the
humidifier will only operate with Humidity
Control set on maximum.
Humidity
Rel.
Allow 24 hours for humidifier to adjust.
Relative Humidity
Operating Tips for Best Performance
1. Position the humidifier at least 2 inches
from any wall and away from any heat registers.
4. Regular cleaning as instructed in
“Cleaning Your Humidifier” section of this
manual is recommended.
2. Do not restrict airflow from entering or exiting the humidifier.
5. Replace the evaporative wicking filters at
least once per humidification season or
more depending on water conditions in
your area.
3. Use Emerson recommended bacteriostat
WT-BC to retard bacteria growth that may
cause odors and may be harmful to your
health.
8
HD1300 3 US manual
11/14/00
1:40 PM
Page 9
Replacement and Care of Filters
WARNING: To reduce the risk of shock
or injury from moving parts, always
unplug humidifier before removing or
replacing any parts.
CAUTION: To help retard bacteria
growth and keep maximum efficiency,
the filters should be replaced at least
once a season, or more often under hard
water conditions. Use Emerson HDC-12
recommended replacement filter.
All filters may be rinsed in clear water only.
Take care not to damage paper.
To replace the evaporative wicking filters in
your Emerson humidifier, follow the instructions below.
1. Unplug humidifier, and proceed to clean.
Before removing the filters, we recommend moving the humidifier to an area
where floor coverings are not susceptible
to water damage, i.e. kitchen or bath
areas.
Pivoting
Lid
Fan
Assembly
2. Open the pivoting lid and remove water
bottles and set aside. Grasp the fan
assembly front centre and rear centre. Lift
off and set aside on a clean flat surface.
The filter assemblies are now accessible.
3. Lift filter housings out of cabinet and place
where you may work on them comfortably.
With a soft, absorbent cloth, remove any
remaining water or loose mineral deposits
not trapped in the filter from the humidifier
cabinet.
4. To open filter housing for easy access to
filters
a. Deflect the two spring tabs on top of filter housing. Lift top cover off of the filter housing and set aside.
b. Remove the two filters and dispose of
properly. Clean internal parts of humidifier per the “Cleaning Your Humidifier“
section of your owner’s manual.
9
Spring
Tabs
Filter
Housing
HD1300 3 US manual
11/14/00
1:40 PM
Page 10
Replacement and Care of Filters (continued)
c. Install new filters in the filter housing
track with the glue beads of the wicking
pad to the inside of the filter housing.
Fixed Tabs
Spring Tabs
d. Return the top cover of the filter housing by installing the cover over the fixed
tabs on the rear of the lower filter housing and pivoting the cover down over
the top of the filters. Snap the cover
over the two spring tabs.
Filter
Housing
e. Replace the filter housing in the cabinet. Note: There is a left and a right filter housing. There is also a front and
back orientation. To position the filter
housings correctly:
Rear of
Humidifier
• Make sure the two indents in the
cylinder section of the top covers are
positioned towards the centre of the
cabinet.
• Be sure that spring tabs of filter housings are towards front of cabinet.
Front of
Humidifier
Top
Cover
Indents
Towards
Centre
of Cabinet
• Align the lower portion of the filter
assembly over the six ribs, located at
the bottom rear of the humidifier cabinet.
f. Position fan assembly onto the cabinet.
Make sure the fan venturi (lowest cylinder section below the fan) is placed
inside the filter housing.
g. Replace water bottles.
h. Close the pivoting lid on the fan assembly.
i. The unit is ready for use or to be stored
away for the next season.
Flat Portion of Filter Housing
Towards Back of Cabinet
NOTE: For correct operation of the filter
housing assembly, filters must be fully contained inside the flange of the top cover.
Indents Toward Centre of Cabinet
Step 4.e.
10
HD1300 3 US manual
11/14/00
1:40 PM
Cleaning Your Humidifier
CAUTION: To reduce the risk of injury,
fire or damage to humidifier, use only
cleaners specifically recommended for
humidifiers. Never use flammable, combustible or poisonous materials to clean
your humidifier. To reduce the risk of
scalds and damage to humidifier, never
put hot water in humidifier.
CAUTION: Local water purity may vary
from area to area and under certain conditions water impurities and airborne
bacteria may promote the growth of
microorganisms in the reservoir of a
humidifier.
To retard bacteria growth that may
cause odors and be harmful to your
health, use only Emerson HDC-12
replacement filters. We also recommend
using Emerson WT-BC EPA registered
bacteriostat, and cleaners specifically
recommended for humidifiers available
at your local retail store or by calling
(800) 654-3545.
NOTE: If it is necessary to use an approved
bacteriostat, follow the directions correctly.
The bottles of the 13 gallon unit will hold 23/8 gallons of water each.
Step 1
To make cleaning easier, the humidifier cabinet should be empty and completely dried
out. To accomplish this, use the following
method:
a. Allow the humidifier to run until the automatic shutoff turns the humidifier “OFF”.
b. Unplug humidifier
WARNING: If humidifier is not unplugged, fan could start after housing is
removed.
Page 11
Step 2
To Remove Parts
a. Open the pivoting lid and remove water
bottles and set aside. Grasp the fan
assembly front center and rear center. Lift
off and set aside on a clean flat surface.
The filter housings are now accessible.
b. Before removing the internal parts of the
humidifier cabinet, we recommend moving
the humidifier to an area where floor coverings are not susceptible to water damage, i.e., kitchen or bath area. Lift the filter
housing assemblies out of the cabinet and
set to the side.
c. Remove the water level float from the
humidifier cabinet by pinching the float
retainer at the back of the cabinet to
release it. The cabinet should be empty
before cleaning. The cabinet consists of
the lower areas of the humidifier where the
filters are during normal operation time.
d. Empty cabinet of any remaining water.
e. Proceed to “Bi-Weekly Maintenance” or
“End of Season Maintenance” then continue as described below.
f. Remove old filters and dispose of properly
as described on page 9 and 10.
Step 3
Install new filters (use Emerson HDC-12
Replacement Filters) into the location where
the old filters were positioned. Install water
level float at back of cabinet. Ensure that you
slide the float retainer down to the lowest
position in slot at back of cabinet. (See diagram of slot below). Install the filter housings
with the new filters into the correct location.
Position the fan assembly on top of the cabinet and return the humidifier to the desired
location for use.
Refill humidifier bottles with fresh cool water.
Plug the unit into a 120 volt A.C. power outlet
and set the controls per the “Operating
Humidifier Controls” section of this manual.
Position Float Retainer in
bottom of slot
11
FLOAT RETAINER SLOT AS VIEWED
FROM BACK OF CABINET
HD1300 3 US manual
11/14/00
1:40 PM
Page 12
Cleaning Your Humidifier (continued)
2. Empty humidifier cabinet after 20 minutes. Rinse with water until bleach smell
is gone. Allow unit to dry out completely.
Bi-Weekly Maintenance
Removing Scale
1. Fill the humidifier cabinet with one 8 oz.
cup of undiluted white vinegar. Let solution stay 20 minutes.
3. Water bottles should be cleaned in same
manner.
2. Clean all interior surfaces with soft brush.
Dampen a soft cloth with undiluted white
vinegar and wipe out the humidifier cabinet to remove scale.
1. Follow bi-weekly maintenance instructions
at end of humidification season.
End of Season Maintenance
2. Remove and throw away filters.
3. Rinse thoroughly with clean warm water
to remove scale and cleaning solution
before disinfecting the humidifier cabinet.
3. Let humidifier dry completely before storing. Do not store with water inside cabinet.
4. Dust the fan assembly and outside surfaces with a soft cloth only.
4. Store in cool, dry location.
5. Install new filters into a clean humidifier
before next season begins.
Disinfecting Humidifier Cabinet and
Bottles
1. Fill humidifier cabinet with 1 teaspoon
chlorine bleach in 1 gallon of water. Let
solution stay 20 minutes, swishing every
few minutes. Wet all surfaces normally
exposed to water.
6. “Bi-Weekly Maintenance” is also recommended if you do not plan to run the
humidifier for one week or more.
12
HD1300 3 US manual
11/14/00
1:40 PM
Page 13
Troubleshooting
TROUBLE
PROBABLE CAUSE
REMEDY
Unit will not run • Selected humidity level has
been established
and Fill Light is
• No power
not illuminated.
• Raise humidistat setting if desired
• Check 120 volt source for power
Unit will not shut • Float is not free
• Float retainer positioned in top
off
slot at back of cabinet
• Free float from obstruction
• Slide float retainer down to lowest
position in slot at back of cabinet.(See diagram on page 11.)
Unit will not dry • This is normal
out completely
• A small amount of water remains
in the cabinet after the Fill Light
comes on.
Bottles continue to • Air is entering water bottles
empty
• Check “E-Z-Fill Side-Caps” to
ensure tightness
• Check for leak in water bottles
• Ensure gaskets for “E-Z-Fill Side
Caps” are in place (see repair
parts list).
Unit is not
emptying during
use
• Dirty filters
• Bottle cap plunger missing post
in bottom of cabinet.
Unit runs and • Unit is not setup on a level surface (Float will not sense water
shuts off before
at the rear of the cabinet).
bottles are empty
• Change to fresh new filters.
• Check orientation of bottle.
Reposition so that bottle cap
plunger is depressed by post in
bottom of cabinet.
• Position unit level (some carpet
padding may allow unit to sit lower
in the front than the rear with the
additional weight of water bottles
in the front of the cabinet. Install
coasters under front casters.
CAUTION: Use only Emerson WT-BC EPA Registered Bacteriostat available from
your local retail store or by calling (800) 654-3545.
Use of other water treatment products may damage the filter elements. Under no
circumstances should you use water treatment products designed for Rotobelt
or Ultrasonic humidifiers.
Call 1-800-654-3545
for technical help or parts.
13
HD1300 3 US manual
11/14/00
1:40 PM
Page 14
Repair Parts
24
25
32
27
14
24
25
26
27
30
31
28
29
29
22
23
11
9
33
22
1
14
15 16
35
12
13
8
10
7
4
5
6
2
34
21
20
17
19
18
3
PARTS LIST FOR EMERSON HUMIDIFIERS
MODEL NO. HD1300 3
HD1300 3 US manual
11/14/00
1:40 PM
Page 15
Repair Parts
PARTS LIST FOR EMERSON HUMIDIFIER
MODEL NO. HD1300 3
Key No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
–
Part No.
823884
823730-3
823724-3
826544-1
824117
825976
826400
823910
824691-3
825858
13805-02
823728
826401
824101-1
828200
824690
828192
828191
509229-1
828199-5
823726-2
*
822120
823849
HDC-12
828197
823735
822405-1
822406-1
816069-2
822405-2
828196
821904
826367
*
SP6305
Description
Cover, Dust
Lid, Stationary
Lid, Pivoting
Knob
Cap, Glamour
Label, Control
Cover, Electronics
Switch, Slide
Switch, Variable Speed w/Off
Light, Pilot
Humidistat
Switch, Micro
Enclosure, Electronics
Retainer, Float
Float, Water Level
“E-Z-Fill Side-Cap”
Bottle, Left (Includes Key Nos. 16 & 19)
Bottle, Right (Includes Key Nos. 16 & 19)
Cap, Valve Assembly
Cabinet
Rail, Kick
Screw, Pan Hd. Ty “AB” #10 x 3/4
Caster, Twin Wheel
Support, Filter Lower
† Filter, Evaporative
Support, Upper L.H. Filter
Support, Motor
Motor, Single Speed
Fan
Screw, Pan Hd. “AB” #6 x 1-3/4
Motor
Support, Upper R.H. Filter
Cord w/Plug
Retainer, Micro Switch
Screw, Pan Hd. Ty “AB” #6 x 3/8
Owner’s Manual (not illustrated)
* Standard Hardware Item - May be purchased locally.
† Stock Item. May be purchased locally or call 1-800-654-3545
to order.
15
HD1300 3 US manual
11/14/00
1:40 PM
Page 16
FOR PARTS OR TECHNICAL HELP, CALL
(800) 654-3545
(Please have complete model number)
TM
8100 W. Florissant
St. Louis, Mo. 63136
© 2000 Emerson Electric Co.
Part No. SP6305
Form No. SP6305-1
Printed in Canada 09/00