Samsung SV-DVD1E Instruction manual

01274A SV-DVD1E/XEU-GB1
9/5/56 7:53 AM
Page 1
DVD-VCR
SV-DVD1E
Instruction Manual
www.samsungvcr.com
Downloaded From Disc-Player.com Samsung Manuals
01274A SV-DVD1E/XEU-GB1
9/5/56 7:53 AM
Page 2
Safety Precautions
Contents
GB
CAUTION
◆ FOREWORD
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION. TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE REAR COVER. NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
DANGER
This symbol is intended to alert you to the
presence of dangerous voltage within the
product.
■
Safety Instructions.........................................................................................
6
◆ DVD-VCR OVERVIEWS
■
■
■
■
■
Front View of the DVD-VCR..........................................................................
Rear View of the DVD-VCR...........................................................................
Infrared Remote Control................................................................................
Display Indicators..........................................................................................
Accessories...................................................................................................
7
7
8
9
9
◆ CONNECTING YOUR DVD-VCR
IMPORTANT NOTE
■
■
■
The mains lead on this equipment is supplied with a
moulded plug incorporating a fuse. The value of the fuse is
indicated on the pin face of the plug. If it requires
replacing, a fuse approved to BS1362 of the same rating
must be used.
Never use the plug with the fuse cover omitted if the cover
is detachable. If a replacement fuse cover is required, it
must be of the same colour as the pin face of the plug.
Replacement covers are available from your dealer.
■
CAUTION
This symbol is intended to alert you to the
presence of important instructions
accompanying the product.
■
■
■
■
■
■
■
■
■
■
■
■
However, if there is no alternative to cutting off the plug,
remove the fuse and then safely dispose of the plug. Do
not connect the plug to a mains socket, as there is a risk of
shock hazard from the bared flexible cord.
■
BLUE = NEUTRAL
BROWN = LIVE
As these colours may not correspond with the coloured
markings identifying the terminals in your plug, proceed as
follows: The wire coloured BLUE must be connected to the
terminal marked with the letter N or coloured BLUE or
BLACK. The wire coloured BROWN must be connected to
the terminal marked with the letter L or coloured BROWN
or RED.
Inserting Batteries in the Remote Control......................................................
Setting the Date and Time.............................................................................
Displaying/Hiding On-Screen Information.....................................................
Setting the DVD-VCR Output Channel..........................................................
Presetting the Stations Automatically............................................................
Presetting the Stations Manually...................................................................
Clearing a Preset Station...............................................................................
Changing the Preset Station Table................................................................
18
18
19
19
20
21
22
23
◆ RECORDING TELEVISION BROADCASTS
■
■
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code: -
10
11
11
12
13
13
14
15
16
17
◆ SETTING UP YOUR DVD-VCR
■
If the fitted plug is not suitable for the power points in your
house or the cable is not long enough to reach a power
point, you should obtain a suitable safety approved
extension lead or consult your dealer for assistance.
Deciding How to Connect DVD-VCR.............................................................
Connecting DVD-VCR to the TV using the Coaxial Cable............................
Connecting DVD-VCR to the TV using the SCART Cable............................
Connecting DVD-VCR to the Satellite receiver or Other Equipment.............
Connecting the Audio Output Cable..............................................................
Plug &Auto Set Up........................................................................................
Tuning Your Television for the DVD-VCR.....................................................
Deck Control Keys.........................................................................................
Basic TV Tuner Operations...........................................................................
Copying from DVD to VCR............................................................................
■
■
■
■
■
■
■
■
■
■
Selecting the Cassette Type..........................................................................
Selecting the Recording Speed.....................................................................
NICAM...........................................................................................................
Switching between the TV and VCR Modes..................................................
Protecting a Recorded Cassette....................................................................
Recording a Programme Immediately...........................................................
Recording a Programme with Automatic Stop...............................................
Using the VIDEOPlus+ Feature.....................................................................
Modifying VIDEOPlus+ Programming...........................................................
Using the Timer Programming Feature.........................................................
Checking a Preset Recording........................................................................
Cancelling a Preset Recording......................................................................
24
24
25
25
26
26
27
28
29
30
31
31
WARNING: DO NOT CONNECT EITHER WIRE TO THE
EARTH TERMINAL WHICH IS MARKED WITH THE
LETTER E OR BY THE EARTH SYMBOL
, OR
COLOURED GREEN OR GREEN AND YELLOW.
2
Downloaded From Disc-Player.com Samsung Manuals
3
01274A SV-DVD1E/XEU-GB1
9/5/56 7:53 AM
Page 4
Contents (cont.)
Contents (cont.)
GB
GB
◆ PLAYING BACK
Playing a Cassette.........................................................................................
Adjusting Picture Alignment Automatically....................................................
Adjusting Picture Alignment Manually...........................................................
Intelligent Picture Control..............................................................................
Record Source...............................................................................................
Selecting the Colour Mode............................................................................
Selecting the Audio Output Mode..................................................................
Selecting the Audio Mute Mode.....................................................................
■
■
■
■
■
■
■
■
32
32
32
33
33
34
35
35
◆ DVD FUNCTIONS
Using the Setup Menu...................................................................................
Setting Up the Language Features................................................................
Using the Disc Menu Language....................................................................
Setting Up the AUDIO Language Features...................................................
Using the Subtitle Language.........................................................................
Setting Up the Parental Control.....................................................................
Setting Up the Audio Options........................................................................
Setting Up the Display Options......................................................................
58
59
59
60
60
61
62
63
◆ Technical Specifications .......................................................................................
64
■
■
■
■
■
■
■
■
◆ SEARCHINGFOR
A
SEQUENCE
Playing a Cassette in Slow Motion................................................................
Playing a Sequence Frame by Frame...........................................................
Playing a Sequence at Variable Speeds.......................................................
Searching for a Specific Sequence...............................................................
Auto Repeat Play...........................................................................................
Interval Repeat Play......................................................................................
Using the Tape Counter................................................................................
■
■
■
■
■
■
■
36
37
37
38
39
39
40
◆ SOLVING PROBLEMS
■
■
■
Problems and Solutions (VCR)......................................................................
Troubleshooting Guide (DVD).......................................................................
Service Centers List......................................................................................
65
66
67
◆ ADVANCED RECORDING FEATURES
Connecting an RCA Audio/Video Input Cable...............................................
Using the Assemble Edit Function.................................................................
Recording from Another VCR or Camcorder.................................................
Audio Dubbing a Pre-recorded Cassette.......................................................
■
■
■
■
41
42
42
43
◆ OTHER FUNCTIONS AND USEFUL RECOMMENDATIONS
SQPB (Super VHS Quasi PlayBack).............................................................
Auto Power Off..............................................................................................
■
■
44
44
◆ DVD FUNCTIONS
Disc Type and Characteristics....................................................................... 45
Choosing a Connection................................................................................. 46
Playing a Disc................................................................................................47,48
Using the Search & Skip Functions............................................................... 49
Using the Display Function (DVD)................................................................. 50
Using the Display Function (CD/VCD)........................................................... 50
Repeat Play................................................................................................... 51
Program Play (DVD/VCD/CD)....................................................................... 52
Random Playback (DVD/VCD/CD)................................................................ 52
Using the Disc View Function (Track View VCD).......................................... 53
Using the Disc View Function (Index View VCD).......................................... 53
Selecting the Audio Language (Using the AUDIO button)............................. 54
Selecting the Subtitle Language (Using the SUBTITLE button).................... 54
Changing the Camera Angle......................................................................... 55
Using the Mark Function (DVD/VCD)............................................................ 56
Recalling a Marked Scene............................................................................. 56
Clearing a Mark............................................................................................. 56
Using the Zoom (DVD/VCD).......................................................................... 57
3D Sound Function........................................................................................ 57
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
4
Downloaded From Disc-Player.com Samsung Manuals
Symbols
1
1
☛
➢
Press/push
Hold down
Important
Note
1 = Step number
5
01274A SV-DVD1E/XEU-GB1
9/5/56 7:53 AM
Page 6
Front View of the DVD-VCR
Safety Instructions
GB
GB
The following illustrations represent precautions.
The lightning bolt is a warning sign alerting you to dangerous voltage inside the product.
DO NOT OPEN THE DVD-VCR. Refer to service personnel.
STANDBY/ON
BUTTON
VIDEO CASSETTE
COMPARTMENT
DVD DECK
F.F /
SKIP NEXT
BUTTON
RECORD
BUTTON
EJECT
BUTTON
Do NOT expose the DVD-VCR
to extreme temperature conditions (below 5°C and above
40°C) or to extreme humidity
conditions (less than 10% and
more than 75%).
Do NOT expose the DVD-VCR
to direct sunlight.
Do NOT expose the DVD-VCR
to any liquids.
STEREO
HEADPHONE
JACK
HEADPHONES OPEN/CLOSE
VOLUME
BUTTON
CONTROL
DVD/VCR
SELECT BUTTON
COPY
BUTTON
PROGRAMME PLAY/PAUSE STOP
REW /
SELECTION
BUTTON
BUTTON SKIP BACK
BUTTONS
BUTTON
Rear View of the DVD-VCR
Do NOT place any objects on
the DVD-VCR or remote
control.
During a storm and/or lightning, unplug the DVD-VCR
from the mains socket and
aerial.
If the remote control is not
used for a long period of time,
remove the batteries and store
it in a cool, dry place.
AERIAL IN
CONNECTOR
AV2 (DEC./EXT.) SCART
(EURO-21) SOCKET
S-VIDEO OUT
JACK
VIDEO INPUT/OUTPUT
SOCKETS
DIGITAL AUDIO OUT
SOCKET (COAXIAL)
THIS DEVICE IS NOT FOR USE IN INDUSTRIAL
ENVIRONMENTS
OUT TO TV
CONNECTOR
6
Downloaded From Disc-Player.com Samsung Manuals
AV1 (EURO AV) IN/OUT
SCART (EURO-21) SOCKET
RCA AUDIO L, R
IN/OUT SOCKETS
DIGITAL AUDIO OUT
SOCKET (OPTICAL)
7
01274A SV-DVD1E/XEU-GB1
9/5/56 7:53 AM
Page 8
Infrared Remote Control
Display Indicators
GB
GB
1
STANDBY/ON BUTTON
AUTO TRACKING, TRACKING +/VOLUME +/- BUTTONS
2
3
4
5
6
7 8 9
10
11
OPEN/CLOSE BUTTON
SHUTTLE << / >>
PROGRAM +/- BUTTONS
S-VHS BUTTON
MUTE BUTTON
3D SOUNDBUTTON
0-9 / AUDIO DUBBING BUTTON
DVD BUTTON
REWIND/REVERSE PICTURE SEARCH BUTTON
SKIP BACK / RECORD BUTTON
STOP BUTTON
ZOOM / RECORDING SPEED SELECTION BUTTON
ANGLE / TIMERBUTTON
SETUP BUTTON
LAST CHANNEL BUTTON
TV/VCR BUTTON
VCR BUTTON
FAST-FORWARD/FORWARD SEARCH
BUTTON
PLAY/PAUSE BUTTON
SKIP NEXT / FRAME/STEP BUTTON
AUDIO MODE SELECTION BUTTON
SUBTITLE BUTTON
DISPLAY BUTTON
MENU BUTTON
JOYSTICK
TITLE BUTTON
MARK / SEARCH BUTTON
CLEAR BUTTON
AB REPEAT / REPEAT / MODE BUTTON
RETURN / CLOCK/COUNTER BUTTON
➢
12 13 14
15 16
17
18
TV VIEW BUTTON
1 The DVD Deck is active
2 A DVD, CD, VCD or SVCD is loaded
10 The VCR Record Speed is set to SP or LP
11 The VCR Deck is active
3 A disc with LPCM (Linear Pulse Code
Modulation) audio is loaded
12 The status of the DVD deck is graphically displayed
13 3D Sound is active
4 A DVD with a Dolby Digital is loaded
5 A DVD with a DTS soundtrack is loaded
6 The time, counter position, time remaining or
current deck status is displayed
7 The current TV show or video is broadcast in
Stereo
8 The Hi-Fi track of a VHS tape is playing
9 A Timer Recording is programmed or in progress.
If blinking there is an error. Also displays without the
clock hands to indicate that a recording is in progress
and blinks when the VCR is in Pause mode.
14 The DVD has multiple angles to choose from
15 The number to the right of the “T” symbol is the
current title number
16 The number to the right of the “C” symbol is the
current title number
17 DVD to VHS copy is in progress
18 The status of the VCR deck is graphically displayed
Accessories
Function Buttons:
◆ TV VIEW : Output selection key. Select the output that you want to see.
◆ DVD : Remote key active for DVD operation.
◆
◆
◆
◆
If you press DVD button, the DVD is ligthining. It means DVD mode.
ex) If you press ll (PLAY) key, the DVD will be play.
VCR : Remote key active for VCR operation.
If you press VCR button, the VCR is ligthining. It means VCR mode.
ex) If you press ll (PLAY) key, the VCR tape will be play.
JOYSTICK : Use for Up ( ), Down ( ), Left ( ), Right ( ), ENTER key.
MENU : Use for DISC menu of DVD.
SETUP : Use for SETUP menu of DVD or VCR.
8
Downloaded From Disc-Player.com Samsung Manuals
You have just purchased a SAMSUNG Video Cassette Recorder (DVD-VCR).
Together with your DVD-VCR, you will find the following accessories in the box.
REMOTE CONTROL
& BATTERIES
AUDIO & VIDEO
CABLE
OWNER’S
INSTRUCTIONS
COAXIAL CABLE
9
01274A SV-DVD1E/XEU-GB1
9/5/56 7:53 AM
Page 10
Deciding How to Connect DVD-VCR
Connecting DVD-VCR to the TV using the Coaxial Cable
To receive television programmes a signal must be received from
one of the following sources:
GB
◆
◆
◆
◆
You must take into account various factors when connecting audio or video systems:
◆ Types of connectors available on your systems
◆ Systems connected permanently to the DVD-VCR (satellite receiver for example) or
temporarily (camcorder for example)
☛
Your DVD-VCR is equipped with the following connectors.
Connector
Location
Type
Direction
Recommended Use
◆ Television
◆ Satellite receiver
◆ Other VCR
AV1 (EURO AV) Rear
SCART
In/Out
AV2 IN
SCART
In
Rear
Audio input
Rear
Audio output
VIDEO input
Rear
Audio RCA
In
Audio RCA
Out
◆ Satellite receiver
◆ CANAL/DECODER
◆ Other VCR
An outdoor aerial
An indoor aerial
A cable television network
A satellite receiver
2
Make sure that both the television and the DVD-VCR are
switched off before connecting the cables.
1
Remove the aerial or network input cable from the television.
2
Connect this cable to the 75Ω coaxial socket marked
rear of your DVD-VCR.
3
Plug the coaxial cable supplied into the
DVD-VCR.
4
Plug the other end of the coaxial cable into the connector
previously used for the aerial on the television.
5
To obtain better quality pictures and sound on your television, you
can also connect your DVD-VCR to the television via the SCART
cable (see section below) if your television is equipped with this
type of connection.
on the
socket on your
TV
4
◆ AUX Audio in
◆ LINE Audio out
GB
3
Connecting DVD-VCR to the TV using the SCART Cable
◆ AUX Video in
RCA
In
RCA
Out
◆ LINE Video out
S-JACK
Out
◆ S-Video out (DVD only)
Optical
coaxial
Out
◆ Digital Audio out (DVD only)
75 Ω
Out
Aerial
VIDEO output
TV
S-VIDEO
output
Rear
3
2
Digital AUDIO
output
Rear
OUT TO TV
Rear
RF coaxial cable
◆ Television
coaxial
IN FROM ANT. Rear
75 Ω
coaxial
☛
◆ Aerial
◆ Cable television network
◆ Satellite receiver
Refer to the documentation supplied with your equipment for detailed connection instructions
and associated safety precautions.
Downloaded From Disc-Player.com Samsung Manuals
You can connect your DVD-VCR to the television using the SCART cable if the appropriate input is
available on the television. You thus:
◆ Obtain better quality sound and pictures
◆ Simplify the setting up procedure of your DVD-VCR
☛
In
Whenever you connect an audio or video system to your DVD-VCR, ensure that all elements
are switched off.
10
SCART Cable
◆ Regardless of the type of connection chosen, you must always connect the coaxial cable
supplied. Otherwise, no picture will be visible on the screen when the DVD-VCR is switched
off.
◆ Make sure that both the television and the DVD-VCR are switched off before connecting the
cables.
1
Connect the coaxial cable as indicated in the above section.
2
3
Connect one end of the SCART cable to the AV1 (EURO AV) socket on the rear of the DVD-VCR.
Plug the other end into the appropriate connector on the television.
11
01274A SV-DVD1E/XEU-GB1
9/5/56 7:53 AM
Page 12
Connecting DVD-VCR to a Satellite Receiver or Other Equipment
Connecting the Audio Output Cable
GB
GB
You can connect your DVD-VCR to a Satellite receiver or other DVD-VCR using the SCART cable if the
appropriate outputs are available on the equipment chosen. The following illustrations give a few examples
of the connection possibilities.
You can connect your DVD-VCR to a Hi-Fi system.
Example: You wish to take advantage of the quality of your Hi-Fi
stereo system when watching a programme or recording
via your DVD-VCR.
☛
1. AV1(EURO AV): By means of 21-pin Scart Cable
◆ Regardless of the type of connection chosen, you
must always connect the coaxial cable supplied.
Otherwise, no picture will be visible on the screen
when the DVD-VCR is switched off.
Plug the SCART Cable with satellite receiver or other equipment into the AV1 (EURO AV) socket on the rear of the
DVD-VCR.
After making this connection, select the source by pressing the TV VIEW button for the AV1 input sources.
◆ Make sure that both the television and the DVD-VCR
are switched off before connecting the cables.
2. By means of RF Coaxial Cable
After making this connection, you must preset the station received through the satellite tuner.
RF output channel of the satellite receiver should be adjusted away from channel 60, which is used by the
DVD-VCR, e.g. re-adjust to channel 65.
Aerial
Satellite Receiver or other Equipment
1
1
Connect the coaxial cable or SCART as indicated on page 12.
2
Plug the audio output cable into the audio connectors on the rear
of your DVD-VCR.
3
Plug the other end of the audio cable into the appropriate input
connectors on your Hi-Fi stereo system.
➢
Aerial Connector
Respect the colour coding of the left and right channels.
2
2
2
TV
Plug & Auto Set Up
1
SCART Cable
Your DVD-VCR will automatically set itself up when it is plugged
into the mains for the first time. TV stations will be stored in
memory. The process takes a few minutes. Your DVD-VCR will
then be ready for use.
RF coaxial cable
TV
1. AV2 IN: By means of 21-pin Scart Cable
Plug the SCART Cable with satellite receiver or other equipment into the AV2 (DEC./EXT.) socket on the rear of
the DVD-VCR.
After making this connection, select the source by pressing the TV VIEW button for the AV2 input sources.
1
Connect the coaxial cable as indicated on page 12.
(Connecting Your DVD-VCR to the TV Using the Coaxial Cable)
2. By means of RF Coaxial Cable
2
After making this connection, you must preset the station received through the satellite tuner.
RF output channel of the satellite receiver should be adjusted away from channel 60, which is used by the
DVD-VCR, e.g. re-adjust to channel 65.
Plug the DVD-VCR into the mains. It will automatically tune itself
in and store TV stations in the memory.
3
The process will finish after a few minutes. Then the DVD-VCR
automatically switches itself off.
Aerial
Satellite Receiver or other Equipment
Aerial Connector
1
2
➢
☛
Now, you only have to switch the DVD-VCR on and it is
ready for use.
Function for “Plug & Auto Set Up” is fixed already.
So if you want to change this fixed one, you can change
it by Presetting the Stations Automatically in OSD “ Auto
Set Up” menu. (see page 20)
TV
SCART Cable
RF coaxial cable
12
Downloaded From Disc-Player.com Samsung Manuals
13
01274A SV-DVD1E/XEU-GB1
9/5/56 7:53 AM
Page 14
Tuning Your Television for the DVD-VCR
Deck Control Keys
GB
GB
You must tune your television for the DVD-VCR only if you are not
using a Scart cable
➢
2
4
To view pictures from your DVD-VCR when a Scart cable
is used, the television must be set to the audio/video
mode (AV).
1
Switch on the television.
2
Switch on the DVD-VCR by pressing STANDBY/ON on the front of
the DVD-VCR or STANDBY/ON on the remote control.
3
Select a programme position on the television to be reserved for
use with your DVD-VCR.
4
The DVD-VCR uses one set of controls to operate both decks. The
following keys are helpful in successfully controlling each deck.
1
STANDBY/ONButton
Press the STANDBY/ON button on the remote control or front
panel to turn on the DVD-VCR.
2
DVD Button
Press the DVD button on the remote control when you want to
control the DVD deck.
◆ The DVD indicator will light on the Front Panel Display to show
that the DVD deck is selected.
3
VCR Button
Press the VCR button on remote control when you want to control
the VCR deck.
◆ The VCR indicator will light on the Front Panel Display to show
that VHS deck is selected.
Insert the video cassette in the DVD-VCR. Check that the
DVD-VCR starts reading the cassette; if not, press II button.
5
Start a scan on your television or set the television to UHF
channel 60.
6
Fine tune the television until the pictures and sound are obtained
clearly.
7
If you cannot find the pictures and sound, or there is interference
from nearby channels, it may be necessary to change the setting
of the DVD-VCR output channel (see Setting the DVD-VCR
Output Channel on page 19 and Problems and Solutions on page
63).
8
When the picture and sound are perfectly clear, store this channel
at the desired programme position on the television.
Result:
That programme is now reserved for use with your
DVD-VCR.
4
DVD-VCR Toggle
Press the DVD-VCR button on the front panel to toggle control
between the DVD deck and the VCR deck.
5
The TV VIEW Key
Press the TV VIEW key repeatedly to cycle through all of your
input sources, including the DVD, VCR, Tuner (PR##), AV1, AV2
and AUX.
➢
1
1
3
2
Before using the VCR operation of 14~44 pages, press
the VCR button on the remote control to select VCR
mode.
4
Before using the DVD operation of 45~63 pages, press
the TV VIEW button on the remote control to select and
watch DVD.
5
14
Downloaded From Disc-Player.com Samsung Manuals
15
01274A SV-DVD1E/XEU-GB1
9/5/56 7:53 AM
Page 16
Basic TV Tuner Operations
Copying from DVD to VCR
GB
GB
The following buttons are used when watching television via the
DVD-VCR’s built-in TV tuner.
The DVD-VCR allows you to copy the contents of a DVD to a VHS
tape with a press of the COPY button.
2
1
TV/VCRButton
Press to switch between your TV’s tuner and the VCR’s internal
tuner.
2
PROG Up/Down Button
Press to change to the next or previous channel.
3
0-9 Buttons
Press to select channels directly.
4
Last Programme
Press to jump directly to the previously viewed channel.
5
Volume/Mute
Press to adjust the volume of the programme you are watching.
Press Mute to toggle the sound on and off.
◆ Also works in DVD and VCR mode.
6
Display
Press to display the channel you are watching.
◆ Also works in DVD and VCR mode.
2
1
3
4
If the DVD you are attempting to copy is copy
protected, you will not be able to copy the disc. It is not
permitted to copy Macrovision® encoded DVDs.
1
Insert Disc
Insert the disc you wish to copy in the DVD deck and close the
drawer.
2
Insert VHS Tape
Insert a blank VHS videotape into the VCR deck.
3
Copy the DVD to VHS Tape
Press the COPY button on the DVD-VCR front panel.
◆ The DVD will go into Play mode and the VCR will go into Record
mode.
◆ If the DVD disc menu appears, you may need to press the PLAY
button manually to begin copying.
4
1
2
Stop the Copy Process
When the DVD is finished playing, press the VCR button on the
remote control and then press the STOP button to end the copy.
◆ You must stop the Copy process manually when the DVD movie
ends or the DVD may replay and record over and over again.
☛
For NTSC DVD or VCD copy
3
◆ Before starting the copy process, set the Quasi PAL to
Off in Display options of DVD SETUP MENU.
(see page 63)
◆ If Quasi PAL is On, the copy process can not active.
◆ The copy is only active PAL tape system.
5
5
4
4
5
6
16
Downloaded From Disc-Player.com Samsung Manuals
17
01274A SV-DVD1E/XEU-GB2
9/5/56 7:54 AM
Page 18
Displaying/Hiding On-Screen Information
Inserting Batteries in the Remote Control
GB
You must insert or replace the batteries in the remote control when
you:
◆ Purchase the DVD-VCR
◆ Find that the remote control is no longer working
correctly
1
1
Push the tab in the direction of the arrow to release the battery
compartment cover on the rear of the remote control.
1
Press SETUP on the remote control.
Result:
The programming menu is displayed.
2
Insert two AA, R6 or equivalent batteries, taking care to respect
the polarities:
◆
+ on the battery with + on the remote control
◆
– on the battery with – on the remote control
2
Press the corresponding
USER SET option.
3
Press the ENTER button to select this option.
Result:
The USER SET menu is displayed.
Replace the cover by aligning it with the base of the remote
control and pushing it back into place.
4
Press the corresponding or
in front of the OSD option.
5
To...
Press
Display on-screen information
ON is displayed.
Hide on-screen information
OFF is displayed.
3
➢
Do not mix different battery types (manganese and
alkaline for example).
GB
Your DVD-VCR displays most information both on the DVD-VCR
and the television.
You can choose to display or hide this information on the television
screen (except for the Index, Programming MENU and
Timer functions, which cannot be hidden).
Setting the Date and Time
6
,
or ,
buttons to select the
buttons, until the cursor is placed
or , until...
USER SET
ENTER
E N
D:SETUP
OSD
TAPE SELECT
COLOUR SYSTEM
IPC
NICAM
RECORD SOURCE
:ON
:E180
:AUTO
:ON
:ON
:AUTO
E D
N:SETUP
On completion, press SETUP twice to exit the menu.
Your DVD-VCR contains a 24-hour clock and calendar used to:
◆ Automatically stop programme recording
◆ Preset your DVD-VCR to record a programme
automatically
You must set the date and time when:
◆ You purchase the DVD-VCR
◆ The power supply remains off for more than 60 minutes
☛
CLOCK SET
ENTER
◆ The time and date are set automatically from the
broadcast signal. If the signal is weak or ghosting
occurs, the time and date may not be set automatically. In this case, they should be set manually.
E N
D:SETUP
◆ Do not forget to reset the time when you change
clocks from winter to summer time and vice versa.
12:00
1/JAN/2000
SAT
Your DVD-VCR output channel may need to be changed if the
pictures suffer from interference or if your TV cannot find the
pictures.
Also, you can change the DVD-VCR output channel to adjust the
frequency in which information is displayed on the screen.
1
Press SETUP on the remote control.
Result:
The programming menu is displayed.
2
Press the corresponding
INSTALLATION option.
Press the ENTER button to select this option.
Result:
The CLOCK SET menu is displayed.
3
Press the ENTER button to select this option.
Result:
The INSTALLATION menu is displayed.
4
Press or to select the hour, minutes, day, month and year.
Result:
The option selected flashes.
4
Press the
buttons, until the cursor is placed in front of the
VCR OUTPUT CH option.
5
Press the or buttons to increase or decrease the value.
Result:
The day of the week is displayed automatically.
5
Select the required output channel (CH21~CH69) by pressing the
or buttons.
6
On completion, press SETUP twice to exit the menu.
Then tune your television again (see page 14).
1
Press SETUP on the remote control.
Result:
The programming menu is displayed.
2
Press the corresponding
CLOCK SET option.
3
AUTO CLOCK : ON
E N
D:SETUP
Setting the DVD-VCR Output Channel
➢
6
18
Downloaded From Disc-Player.com Samsung Manuals
,
or
,
buttons to select the
You can hold the or buttons down to scroll more
quickly through the values.
On completion, press SETUP twice to exit the menu.
,
or
,
buttons to select the
or
INSTALLATION
ENTER
E N
D:SETUP
AUTO SET UP
MANUAL SET UP
VCR OUTPUT CH
:CH60
E N
D:SETUP
19
01274A SV-DVD1E/XEU-GB2
9/5/56 7:54 AM
Page 20
Presetting the Stations Manually
Presetting the Stations Automatically
GB
GB
☛
2,3
1
ENTER
1
Press the SETUP button on the remote control.
Result:
The programming menu is displayed.
You must preset the stations received through the tuner. This can
be done:
◆ Plug & Auto Set up (see page 13)
◆ Automatically
◆ Manually (see page 21)
2
Press the corresponding ,
INSTALLATION option.
3
Press the ENTER button to select this option.
Result:
The INSTALLATION menu is displayed.
1
Press the SETUP button on the remote control.
Result:
The programming menu is displayed.
2
Press the corresponding ,
INSTALLATION option.
3
Press the ENTER button to select this option.
Result:
The INSTALLATION menu is displayed.
or ,
buttons to select the
E N
D:SETUP
4
AUTO SET UP
MANUAL SET UP
VCR OUTPUT CH
:CH60
E D
N:SETUP
5
YOUR DATA WILL BE LOST
PRESS ENTER TO CONTINUE
SETUP TO EXIT
PLEASE WAIT
Press the corresponding or buttons, until the cursor is placed
in front of the AUTO SET UP option.
And then press the button to select this option.
Result:
A message appears, indicating that any channels
already preset on your DVD-VCR will be deleted.
Press ENTER to start the auto scanning.
Result:
◆ The P L E A S E W A I
indication
T
flashes on the
television screen.
◆ The first frequency band is scanned and the first
station found is displayed and stored.
◆ The DVD-VCR then searches for the second station
and so on.
◆ When the automatic scanning procedure has
finished, the DVD-VCR switches automatically to
programme 1.
➢
6
AUTO SET UP
You do not need to preset the stations manually if you
have already set them automatically.
Your DVD-VCR contains a built-in tuner used to receive television
broadcasts.
You can store up to 99 stations.
INSTALLATION
☛
You do not need to preset the stations if you have already
set them automatically (see Plug & Auto Set Up on
page 13).
➢
2%
I--------------------I
Downloaded From Disc-Player.com Samsung Manuals
INSTALLATION
Press the corresponding or buttons, until the cursor is placed
in front of the MANUAL SET UP option.
5
Press the
Result:
6
Press the
required.
7
Press the
Result:
8
Press the or buttons to start scanning.
Result:
The frequency band is scanned and the first station
found is displayed.
9
Press the or buttons until the cursor is placed in front of the
NAME.
The station name is set automatically from the broadcast signal.
10
To change the programme’s name, press the button.
Result:
The first letter of the name flashes.
11
To...
Then...
Select a character
in the name
Press the or button until the
required character is displayed
(letters, numbers or “-” character).
Move to the next or
previous character
Press the or
respectively.
12
button to select a MANUAL SET UP option.
The TV STATION TABLE menu is displayed.
or
buttons to select a programme number as
If you...
Then...
Wish to store the
station displayed
◆
◆
◆
Do notwish to
store the station
displayed
◆ The time and date are set automatically from the
broadcast signal. If the signal is weak or ghosting
occurs, the time and date may not be set automatically. In this case, they should be set manually (see
page 18).
ENTER
E N
D:SETUP
AUTO SET UP
MANUAL SET UP
VCR OUTPUT CH
button to preset the station.
The MANUAL SET UP menu is displayed.
If you wish to cancel the auto scanning before the end, press the
SETUP button three times to exit the menu.
◆
◆
◆
E N
D:SETUP
20
buttons to select the
4
The number of stations automatically stored by the DVDVCR depends on the number of stations that it has found.
◆ Once the auto scanning procedure has finished, some
stations may have been stored more than once; select
the stations with the best reception and delete the
ones no longer required (see page 22).
or ,
:CH60
E D
N:SETUP
** TV STATION
P R CH
1 --2 --3 --4 --5
TABLE **
NAME
-------------
SET:
SORT:ENTER
DELETE:CLEAR
SETUP
buttons
Press the or buttons to place the
cursor in front of the MFT.
Press the or buttons to adjust the
picture, if necessary.
Press OK to store the station
* *MANUAL SET UP * *
P R
C H
MFT
NAME
: 1
: --: : BBC1
MEMORY:ENTER
END: SETUP
Press the or buttons until the
cursor is placed in front of the CH.
Press the or buttons to go on
scanning the frequency band and display
the next station
Go back to the beginning of Step 12
13
Repeat this procedure from Step 6 onwards, until all the required
stations have been stored.
14
On completion, press the SETUP button three times to exit the
menu.
21
01274A SV-DVD1E/XEU-GB2
9/5/56 7:54 AM
Page 22
Clearing a Preset Station
Changing the Preset Station Table
GB
GB
You can rearrange the Station Table and give different programme
numbers to the stations listed according to your own preferences.
If you have stored a TV station:
◆ That you do not require
◆ At the wrong programme position
you can cancel it.
1
2
INSTALLATION
ENTER
E N
D:SETUP
AUTO SET UP
MANUAL SET UP
VCR OUTPUT CH
Press the SETUP button on the remote control.
2
Press the corresponding ,
INSTALLATION option.
3
Press the ENTER button to select this option.
Result:
The INSTALLATION menu is displayed.
4
Press the corresponding or buttons, until the cursor is placed
in front of the MANUAL SET UP option.
5
Press the button to select this option.
Result:
The TV STATION TABLE menu is displayed.
6
Press the corresponding or buttons, until the cursor is placed
in front of the required preset TV station. (PR)
7
Press the CLEAR button.
8
Repeat the same procedure from Step 6 onwards until all the
required stations have been cleared.
9
On completion, press the SETUP button three times to exit the
menu.
:CH60
E D
N:SETUP
** TV STATION
P R CH
1 021
2 025
3 030
4 065
5 055
1
TABLE **
NAME
----------------
SET:
SORT:ENTER
DELETE:CLEAR
SETUP
or ,
buttons to select the
Press the SETUP button on the remote control.
Press the corresponding
,
or
,
buttons to select the
INSTALLATION option.
3
Press the ENTER button to select this option.
Result:
The INSTALLATION menu is displayed.
4
Press the corresponding or buttons, until the cursor is placed
in front of the MANUAL SET UP option.
5
Press the button to select this option.
Result:
The TV STATION TABLE menu is displayed.
6
Press the corresponding or buttons, until the cursor is placed
in front of the required preset TV programme.
Result:
The selected station is displayed at the same time on
the television screen.
7
To change the programme number assigned to a station (PR4
instead of PR1 for example):
◆
Press ENTER
◆
Press the or buttons until the cursor is placed in front of
the programme to which the station is to be moved
◆
Press ENTER again
8
You can modify this station by repeating the same procedure from
Step 6 onwards.
9
On completion, press the SETUP button three times to exit the
menu.
** TV STATION TABLE * *
P R CH
NAME
1 021
---2 025
---3 030
---4 065
---5
SET:
SORT:ENTER
DELETE:CLEAR
SETUP
** TV STATION TABLE * *
P R CH
NAME
1 021
---2 025
---3 030
---4 ( 065
---- )
5
(SORT : 4 ➛ 4 )
EXECUTE:ENTER SETUP
** TV STATION TABLE * *
P R CH
NAME
1 ( 065
---- )
2 025
---3 030
---4 065
---5
(SORT : 4 ➛ 1 )
EXECUTE:ENTER SETUP
** TV STATION
P R CH
1 065
2 021
3 025
4 030
5
TABLE * *
NAME
-------------
SET:
SORT:ENTER
DELETE:CLEAR
SETUP
22
Downloaded From Disc-Player.com Samsung Manuals
23
01274A SV-DVD1E/XEU-GB2
9/5/56 7:54 AM
Page 24
Selecting the Cassette Type
NICAM
GB
If you wish to use the tape counter to display the time remaining on
a cassette, you must indicate the type of cassette inserted.
1
Press SETUP on the remote control.
Result:
The programming menu is displayed.
2
Press the corresponding
USER SET option.
3
Press the ENTER button to select this option.
4
5
1
Press SETUP on the remote control.
Result:
The programming menu is displayed.
2
Press the corresponding
USER SET option.
Press the corresponding or buttons, until the cursor is placed
in front of the TAPE SELECT option.
3
Press the ENTER button to select this option.
Result:
The USER SET menu is displayed.
Press the
or buttons as many times as required, until the
correct cassette length is displayed.
4
Press the corresponding or
buttons, until the cursor is
placed in front of the NICAM option.
5
To...
Press
Mono mode
OFF is displayed.
,
or ,
buttons to select the
USER SET
ENTER
E N
D:SETUP
OSD
TAPE SELECT
COLOUR SYSTEM
IPC
NICAM
RECORD SOURCE
:ON
:E180
:AUTO
:ON
:ON
:AUTO
E180
E 300
6
E240
E260
GB
NICAM programmes are divided into 3 types. NICAM Stereo,
NICAM Mono and Bilingual (transmission in another language).
NICAM programmes are always accompanied by a standard mono
sound broadcast and you can select the desired sound.
Please refer to page 35.
Press SETUP twice to exit the menu.
,
or ,
buttons to select the
or , until...
OFF: Only set at this position to record the
standard mono sound during a
NICAM broadcast if the stereo sound
is distorted due to inferior reception
conditions.
E D
N:SETUP
NICAM mode
USER SET
ENTER
E N
D:SETUP
OSD
TAPE SELECT
COLOUR SYSTEM
IPC
NICAM
RECORD SOURCE
E D
N:SETUP
ON is displayed.
ON: Normally set at this position.
6
Selecting the Recording Speed
You can record a cassette at two different speeds:
◆ SP (Standard Play)
Type
Recording Time (in SP)
E-180
180 mins. or 3 hours
E-240
240 mins. or 4 hours
E-260
260 mins. or
4 hours and 20 mins.
E-300
300 mins. or 5 hours
◆ LP (Long Play)
In Long Play modes:
On completion, press SETUP twice to exit the menu.
Switching between the TV and VCR Modes
The TV/VCR button allows you to record one channel with the VCR
while you watch another channel on the TV.
◆ Each cassette lasts twice as long
◆ The recording is of a slightly lower quality
To record a cassette...
Press the SPEED button on the
remote control, until...
In standard play mode
In long play mode
SP is displayed.
LP is displayed.
24
Downloaded From Disc-Player.com Samsung Manuals
Your television...
On
The television receives the picture from
the VCR and you can select channels
with the PROG ( or ) buttons on the
VCR or the remote control.
Off (or the VCR is turned off)
The television receives the picture from
your home aerial or cable television
system as it did before you connected
the VCR.
You can then use the programme ( or
) buttons on your television to select
the channels.
:ON
:E180
:AUTO
:ON
:ON
:AUTO
25
01274A SV-DVD1E/XEU-GB2
9/5/56 7:54 AM
Page 26
Protecting a Recorded Cassette
Recording a Programme with Automatic Stop
GB
GB
Video cassettes have a safety tab to prevent accidental erasure.
When this tab has been removed, you cannot record on the tape.
1
If you wish to protect a cassette, break off the tab using a small
screwdriver.
2
To re-record over a protected cassette (safety tab broken), cover
the hole with adhesive tape.
1
This function enables you to record up to nine hours (LP) of
programmes.
Your DVD-VCR stops automatically after the requested length of
time.
1
Switch on the television.
2
To monitor the programme being recorded, select the television
channel reserved for use with your DVD-VCR (or the AV input if
used).
3
Recording a Programme Immediately
4
Before recording a programme, you must have preset the corresponding station (unless you are recording via an external video
source). If you have not done so, refer to pages 20 and 21.
Switch on the television.
2
To monitor the programme being recorded, select the television
channel reserved for use with your DVD-VCR (or the AV input if
used).
3
Insert the cassette on which the programme is to be recorded,
with the window visible and the safety tab intact or the opening
covered with adhesive tape.
Result:
The DVD-VCR is switched on automatically.
4
Select:
◆
The station to be recorded using the PROG(
or
4
6
5
or
6
Hold REC ( I ) down for a while to start recording.
Result:
The record indicator appears on the television and DVDVCR display. An index is recorded on the tape (see
page 38).
7
To stop recording, press ■ once.
➢
26
Downloaded From Disc-Player.com Samsung Manuals
) buttons
Select the recording speed by pressing the SPEED button as
many times as required (see page 24).
6
Hold the REC button ( I ) down for a while to start recording.
Result:
The record indicator appears on the television screen
and DVD-VCR display. An index is recorded on the
tape (see page 38).
7
Press the REC button ( I ) several times to increase the
recording time in:
◆
30-minute intervals up to four hours
◆
1-hour intervals up to nine hours (LP)
Result:
The length is displayed on the television displays. The
selected programme is recorded for the length of time
requested. At the end of that time, the DVD-VCR stops
recording automatically.
The AV1, AV2 or AUX source using the TV VIEW button for a
satellite tuner or external video source
Result:
The station number is displayed and the programme
can be seen on the television.
7
or
5
◆
Select the recording speed by pressing the SPEED button as
many times as required (see page 24).
Select:
◆
The station to be recorded using the PROG(
or
4
4
The AV1, AV2 or AUX source using the TV VIEW button for a
satellite tuner or external video source
Result:
The channel number is displayed and the programme
can be seen on the television.
) buttons
5
Insert the cassette on which the programme is to be recorded,
with the window visible and the safety tab intact or the opening
covered with adhesive tape.
Result:
The DVD-VCR is switched on automatically.
◆
4
1
3
8
6
5
LENGTH 2:30
SET LENGTH :
PRESS REC ●
If you wish to cancel the recording before the end, press
STANDBY/ON.
☛
If the end of the tape is reached while recording:
◆ The recording stops
◆ The DVD-VCR automatically turns off
◆ If your DVD-VCR ejects the cassette when you start
recording, check to make sure that the cassette’s
safety tab is intact or that the opening (created by a
broken safety tab) is covered with adhesive tape.
◆ If you reach the end of the tape while recording, the
cassette rewinds automatically.
27
01274A SV-DVD1E/XEU-GB3
9/5/56 7:56 AM
Page 28
Using the VIDEOPlus+ Feature
Modifying VIDEOPlus+ Programming
GB
GB
Before presetting your DVD-VCR:
◆ Switch on both the television and your DVD-VCR
◆ Check that the date and time are correct
◆ Insert the cassette on which the programme is to be
recorded (safety tab intact)
1
Up to six programmes can be preset.
1
STANDARD TIMER
VIDEO PLUS
VIDEOPLUS
3
CODE ---------
PR
1
------
CORRECT:
END:SETUP
1/JAN SAT 12:09
DAY START STOP V/P
SA 9 12:00→12:50SP ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- -
DELETE:CLEAR
If you wish to correct the VIDEOPlus+ code that you are
entering:
◆ Press the button until the digit to be corrected is
cleared
◆ Enter the correct digit
Press the SETUP button.
Result:
The information concerning the programme is displayed.
☛
CODE:0-9
When using the VIDEOPlus+ function for the first time with
stored stations, the programme number flashes. This one
time, you must enter the station number manually by
pressing the or buttons. Refer to the following page if:
◆ The programme number or times flash
◆ You wish to modify the programme
4
If the programme and times are correct, press the SETUP button.
5
Press the STANDBY/ON button to activate the timer.
6
Refer to page 31 if you wish to:
Check that your DVD-VCR has been programmed correctly
Cancel a preset recording
◆
◆
SETUP
Then...
◆ Press the
☛
The numbers next to each TV programme listing are
VIDEOPlus+ code numbers, which allow you to
programme your videorecorder instantly with the remote
control. Tap in the VIDEOPlus+ code for the programme
you wish to record.
or
buttons, until the PR selection flashes.
◆ Press the TV VIEW button one or more times to change the
input source selection.
Result:
The programme number is replaced by:
• The AV1, AV2 or AUX source using the TV
VIEW button for a satellite tuner or external
video source
If all six programmes have been set, the message TIMER
I S F U L L is displayed. Refer to page 31 if you wish to
cancel a preset recording.
Press the numeric buttons to enter the code opposite the
programme that you wish to record in your television magazine.
➢
END:SETUP
If you wish to...
Select an input source other
than the tuner (AV1, AV2 or AUX)
To enter a VideoPlus, press the TIMER button.
Press the and buttons to select VIDEO PLUS.
Result:
A message is displayed to allow you to enter the
VIDEOPlus+ code.
☛
2
If you wish to correct the programme displayed or modify certain elements, such as the recording
speed, you can do so before you press SETUP a second time to confirm.
➢
Record a programme every day
(Monday to Sunday) at the same time
The input source must be selected before changing any
other value.
◆ Press the
◆ Press the
or buttons, until the DAY selection flashes.
or buttons, until the DLY (Daily) value is
displayed.
Record a programme every week
on the same day and at the same time
Extend the recording time
◆ Press the
or buttons, until the DAY selection flashes.
or buttons, until the W- (Week) value is
displayed, followed by the required day.
Example: W-SA (Weekly Saturday)
◆ Press the
◆ Press the
◆ Press the
or buttons, until the STOP selection flashes.
or buttons to increase or decrease the stop
time.
◆ Press the
Select the recording speed
or buttons, until the recording speed selection
flashes.
◆ Press the
or buttons until the correct indication is
displayed:
• AUTO (Auto Tape Speed Select) : see page 30
• SP (Standard Play)
• LP (Long Play)
Select the PDC recording
◆ Press the
◆ Press the
☛
or buttons, until the V/P selection flashes.
or buttons until the “ON” indication is displayed.
Do not select PDC unless you are sure the programme you
wish to record is broadcast with PDC. If you do set PDC ON
(by selecting “ON” in the right - hand column on the screen),
then you must set up the start-time EXACTLY according to
the published TV schedule. Otherwise the timer recording
won’t take place.
5
™ VIDEOPLUS+ is a trademark of Gemstar Development Corporation. The VIDEOPLUS+
system is manufactured under licence from Gemstar Development Corporation.
28
Downloaded From Disc-Player.com Samsung Manuals
29
01274A SV-DVD1E/XEU-GB3
9/5/56 7:56 AM
Page 30
Using the Timer Programming Feature
Checking a Preset Recording
GB
GB
The Timer Programming feature allows you to preset the DVD-VCR
to record a programme up to one month before that programme is
to be broadcast. Up to six programmes can be preset.
☛
STANDARD TIMER
VIDEO PLUS
END:SETUP
PR
1
------
1/JAN SAT 12:09
DAY START STOP V/P
SA 9 12:00→12:50SP ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- -
DELETE:CLEAR
You can check your preset recordings:
◆ When you have finished presetting the DVD-VCR
◆ If you have forgotten which programmes will be
recorded
Before presetting a recording, check that the date and
time are correct.
1
Insert the cassette and press TIMER on the remote control.
Result:
The timer selection is displayed.
2
Press the
Result:
button to select STANDARD TIMER option.
The TIMER PROGRAMMING menu is displayed.
3
Press
4
Select the required station by pressing the , buttons or
TV VIEW to select the AV1, AV2 or AUX input sources.
to select the input source.
5
Press
6
Select the required day by pressing the
7
Press
1
Press TIMER on the remote control.
Result:
The timer selection is displayed.
2
Press the
Result:
button to select STANDARD TIMER option.
The TIMER PROGRAMMING menu is displayed.
3
Press the
4
Press the
or buttons to select and change any values as
required. For more details, refer to the previous page.
5
On completion, press SETUP twice.
or
buttons to select the required programme.
1/JAN SAT 12:09
DAY START STOP V/P
SA 9 12:00→12:50SP ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- SET:
DELETE:CLEAR
SETUP
PR
1
------
to select the recording day.
or
buttons.
to select the recording start time.
SETUP
8
Select the required hour value by pressing the
9
10
Press
11
12
17
or
Select the required minute value by pressing the
Press
buttons.
to select the minutes.
or
buttons.
to select the recording end time.
Select the required recording end time by pressing the or
buttons, following the same procedure as when selecting the
recording start time.
13
Press
14
Press the
or
buttons to select the SP (Standard Play), LP
(Long Play), AUTO (Auto Tape Speed Select) recording speeds.
15
Press the or buttons to toggle between the VPS or PDC
mode (marked ON) and the non-VPS/PDC mode (marked -).
16
17
Cancelling a Preset Recording
to select the recording speed.
You can cancel any programmes that are:
◆ Incorrect
◆ No longer required
1
Press TIMER on the remote control.
Result:
The timer selection is displayed.
2
Press the
Result:
3
Select the programme to be cancelled by pressing the
buttons.
4
Press the CLEAR button to cancel the selected programme.
Result:
All the recording information is deleted and the broadcast will not be recorded.
5
On completion, press SETUP twice.
When you have finished, press the SETUP button.
Press the STANDBY/ON button to activate the timer.
Result:
Before starting recording, the DVD-VCR compares the
timer duration with the remaining time on the cassette.
➢
Auto Tape Speed Select. The DVD-VCR’s “Auto Tape
Speed Select” function compares the duration of the timer
recording to the actual recording time remaining on the
tape loaded. If there is insufficient tape to complete a
timer recording in AUTO mode, the DVD-VCR
automatically switches to LP mode to record the whole
programme.
button to select STANDARD TIMER option.
The TIMER PROGRAMMING menu is displayed.
or
1/JAN SAT 12:09
DAY START STOP V/P
SA 9 12:00→12:50SP ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- ---- --:--→--:---- SET:
DELETE:CLEAR
SETUP
PR
1
------
4
30
Downloaded From Disc-Player.com Samsung Manuals
31
01274A SV-DVD1E/XEU-GB3
9/5/56 7:56 AM
Page 32
Intelligent Picture Control
Playing a Cassette
GB
This function allows you to play back any pre-recorded cassette.
1
Switch on both the television and your DVD-VCR.
1
2
Insert the video cassette to be played. If the safety tab on the
cassette is intact, press ll.
Otherwise, the cassette is played automatically.
During playback, press the SETUP button on the remote control.
Result:
The programming menu is displayed.
2
Press the corresponding
USER SET option.
➢
3
Press the OK button to select this option.
Result:
The USER SET menu is displayed.
4
Press the corresponding or
buttons, until the cursor is
placed in front of the IPC option.
5
Press the
option.
2
3
The Intelligent Picture Control Feature allows you to adjust the
sharpness of the image automatically, according to your own
preferences.
3
When a cassette is loaded, the tape position is optimized
automatically to reduce disturbance (Digital Auto Tracking).
When playing a cassette, if the end of the tape is reached,
the cassette is rewound automatically.
NTSC tapes can be played back but cannot be recorded
with this DVD-VCR.
To...
Then press...
Stop the playback
■ (STOP).
Eject the cassette
(EJECT).
➢
Result:
◆ The tracking bar appears.
◆ The picture is automatically adjusted.
◆ The tracking bar disappears when digital auto tracking has
been completed.
Adjusting Picture Alignment Manually
◆ The image is adjusted.
**
button to turn the
PICTURE
IPC
:
**
OFF
SOFTEN
SHARPEN
--------*----ON/OFF:
If you do not press a button within ten seconds, the
PICTURE menu disappears automatically.
On completion, press the SETUP button again.
Record Source
You can set the SV-DVD1E to record from a variety of sources,
including the Tuner, DVD deck, AV or AUX input. The Auto setting
will record whatever is currently visible on-screen, as set by the TV
VIEW button.
1
Press SETUP on the remote control.
Result:
The programming menu is displayed.
2
Press the corresponding
USER SET option.
3
Press the ENTER button to select this option.
Result:
The USER SET menu is displayed.
4
Press the corresponding or buttons, until the cursor is placed
in front of the RECORD SOURCE option.
5
Press the button to select from the following options.
The DVD-VCR will record from:
◆
◆
◆
When noise bars or streaks appear during playback, adjust alignment
manually by pressing the TRK (+ or -) buttons until the picture is clear and
stable.
◆ The tracking bar appears.
:ON
:E180
:AUTO
:ON
:ON
:AUTO
E N
D:SETUP
When intelligent picture control mode is ON, the sharpness
of the image is adjusted automatically.
Press the or buttons until the picture is displayed according to
your preferences.
The Picture Adjustment feature allows you to adjust the alignment
manually to obtain the best possible picture.
Result:
OSD
TAPE SELECT
COLOUR SYSTEM
IPC
NICAM
RECORD SOURCE
button to select the IPC (intelligent picture control)
7
8
When noise bars or streaks appear during playback, adjust picture
alignment by pressing the ATR button.
buttons to select the
To adjust the sharpness manually, press the
IPC mode OFF.
➢
The Picture Alignment feature enables you to optimize the tape
position automatically to obtain the best possible picture.
or ,
6
3
Adjusting Picture Alignment Automatically
,
GB
◆
◆
6
,
or ,
1
2,3
buttons to select the
AUTO: Whatever is currently visible on screen.
Tuner: The SV-DVD1E’s built-in television tuner.
AV1, AV2: An external source, such as a satellite receiver,
connected to the scart jack.
AUX: An external source, such as a camcoder, connected
to the rear RCA JACK inputs.
DVD: A DVD playing in the DVD deck.
On completion, press SETUP twice to exit the menu.
USER SET
ENTER
E N
D:SETUP
OSD
TAPE SELECT
COLOUR SYSTEM
IPC
NICAM
RECORD SOURCE
:ON
:E180
:AUTO
:ON
:ON
:AUTO
◆ The tracking bar disappears when you release the button.
E D
N:SETUP
32
Downloaded From Disc-Player.com Samsung Manuals
33
01274A SV-DVD1E/XEU-GB3
9/5/56 7:56 AM
Page 34
Selecting the Colour Mode
Selecting the Audio Output Mode
GB
GB
Before recording or playing back a cassette, you can select the
required system standard.
Otherwise, the system automatically selects the reception standard
when you select AUTO.
➢
◆
◆
USER SET
ENTER
E N
D:SETUP
1
OSD
TAPE SELECT
COLOUR SYSTEM
IPC
NICAM
RECORD SOURCE
:ON
:E180
:AUTO
:ON
:ON
:AUTO
E D
N:SETUP
When playing back a cassette, the standard is
automatically selected by the DVD-VCR.
When you playback an NTSC-recorded tape on this DVDVCR make a setting on the colour system according to your
TV. If your TV is a PAL system only TV, set NTPB.
If your TV is Multi System TV (NTSC 4.43 compatible), set
NT4.43 and you can record NT4.43.
Press SETUP on the remote control.
Result:
The programming menu is displayed.
2
Press the corresponding
USER SET option.
3
Press the ENTER button to select this option.
Result:
The USER SET menu is displayed.
4
Press the corresponding or buttons, until the cursor is placed
in front of the COLOUR SYSTEM option.
5
Press the button to select AUTO ➝ PAL ➝ B/W.
AUTO When playing back a cassette, the system standard is
automatically selected by the DVD-VCR.
B/W Black and White
6
On completion, press SETUP twice to exit the menu.
,
or ,
buttons to select the
You can select the mode in which the sound is reproduced on the
loudspeakers and AV outputs. The following options are available.
Option
L
Description
Used to listen to the sound on the left Hi-Fi channel.
R
Used to listen to the sound on the right Hi-Fi channel.
MIX
Used to listen to the mixed sound of the Hi-Fi and normal
channels.
MONO
Used to listen to the sound on the normal mono channel.
LR
Used to listen to Hi-Fi stereo sound on the left and right
channels.
➢
When playing back tapes recorded in Hi-Fi, the
sound switches to Hi-Fi after five seconds of Mono.
L
R
LR
MONO
To select the sound mode, simply press the AUDIO button on the remote
control until the required option is displayed.
Selecting the Audio Mute Mode
You can select the Audio Mute mode.
To select the audio mute mode on and off, simply press the MUTE button
on the remote control.
X
34
Downloaded From Disc-Player.com Samsung Manuals
MIX
35
01274A SV-DVD1E/XEU-GB3
9/5/56 7:56 AM
Page 36
Playing a Cassette in Slow Motion
GB
You can play a cassette in slow motion.
➢
1
1
Press:
◆
1
◆
◆
◆
◆
2
2
ll to start playing the cassette
ll button one more time to make PAUSE mode.
to start SLOW mode.
button as many times as required to decrease or
or
increase the speed respectively
To return to the normal speed, press the ll button twice.
When playing back in slow motion, picture interference may occur.
Press the TRK (+or - ) buttons to minimize this effect.
☛
2
No sound is heard when playing back a cassette in slow
motion.
When you have been using the Slow Motion function for
more than about five minutes, the DVD-VCR will
automatically play to protect the:
◆ Cassette
◆ Video heads
36
Downloaded From Disc-Player.com Samsung Manuals
01274A SV-DVD1E/XEU-GB4
9/5/56 7:59 AM
Page 37
Playing a Sequence Frame by Frame
GB
You can:
◆ Stop the cassette at a given frame (image)
◆ Advance one frame at a time
➢
No sound is heard when playing back frame by frame.
1
1
1
Press:
◆
ll to start playing the cassette
◆
◆
2
ll to stop the tape at a given frame
FRAME/STEP (
) to advance frame by frame
To return to normal playback, press
☛
➢
ll.
When you have been using the Frame-by-Frame function
for more than about five minutes, the DVD-VCR will
automatically play to protect the cassette and video
heads.
Vertical stability: When playing back frame by frame,
interference may be seen on the screen. Press the TRK
(
,
) buttons to minimize this effect.
Playing a Sequence at Variable Speeds
You can vary the playback speed using the Shuttle function (up to
nine times the normal speed).
Example:
You wish to analyze a sportsperson’s technique,
movement by movement.
The Shuttle function is available on the Remote control
➢
1
Press:
◆
◆
◆
2
No sound is heard when playing a sequence at variable
speeds.
ll during playback
SHUTTLE (<<) to play the cassette backwards
SHUTTLE (>>) to play the cassette forwards
1
1
Each time you press a SHUTTLE button, the speed is changed as
shown in the following illustration.
REVERSE REVERSE REVERSE
PLAY
PLAY
PLAY
X9
X7
X3
STILL
SLOW
MOTION
X1/10
SLOW
MOTION
X1/5
PLAY
PLAY
X3
PLAY
X7
PLAY
X9
37
Downloaded From Disc-Player.com Samsung Manuals
01274A SV-DVD1E/XEU-GB4
9/5/56 7:59 AM
Page 38
Searching for a Specific Sequence
Auto Repeat Play
GB
GB
Each time you record a cassette on this DVD-VCR, an “index” is
automatically marked on the tape when recording starts.
The Search function allows you to fast-forward or rewind to a
specific index and start playback from that point. Depending on the
direction selected, the indexes are numbered as follows:
1
etc.
2
➢
INDEX SEARCH : --
Seq. being
Next
Seq.
played
Seq.
1
1
1
Press SETUP on the remote control.
Result:
The programming menu is displayed.
2
Press the corresponding ,
EASY OPERATION option.
3
Press the ENTER button to select this option.
Result:
The EASY OPERATION menu is displayed.
4
Press the corresponding or buttons, until the cursor is placed
in front of the REPEAT PLAY option.
5
To...
Press
Repeat play
ON is displayed.
Do not wish to repeat play
OFF is displayed.
or ,
2
This DVD-VCR uses a standard indexing system (VISS). As
a result, it will recognize any indexes marked by other
VCRs using the same system and vice versa.
To search for a specific index, press INDEX.
2
Press the
or
buttons depending on the direction where your
desired programme is located. Each time you press the
or
buttons, the number decreases or increases respectively.
Result:
The index number is displayed.
6
The DVD-VCR starts to search for the point you specified with the
or buttons.
Result:
When the index is found, cassette playback starts.
Interval Repeat Play
3
➢
buttons to select the
EASY OPERATION
etc.
1
INDEX SEARCH : - 6
2
Prev
You can set repeat play to repeat the tape continuously from
beginning to end.
You can set an index number up to ±20.
ENTER
E D
N:SETUP
AUTO POWER OFF
:OFF
REPEAT PLAY
:OFF
NO. OF
INTERVAL REPEAT : 5
or , until...
E N
D:SETUP
On completion, press SETUP twice to exit the menu.
You can set Interval Repeat Play so that the cassette is repeated a
number of times according to a specified set interval.
1
Press SETUP on the remote control.
Result:
The programming menu is displayed.
2
Press the corresponding ,
EASY OPERATION option.
3
Press the ENTER button to select this option.
Result:
The EASY OPERATION menu is displayed.
4
Press the corresponding or buttons, until the cursor is placed
in front of the NO. OF INTERVAL REPEAT option.
2
5
or ,
buttons to select the
To...
Press
Interval Repeat Play
5, 10, 15 is displayed.
(choose an interval repeat of
5, 10 or 15 times)
Cancel Interval Repeat Play
2,3
1
7
, until...
OFF is displayed.
6
On completion, press SETUP twice to exit the menu.
7
To select Interval Repeat Play during playback, press the
REPEAT button at the desired start point.
Result:
“INTERVAL REPEAT SETTING” is displayed.
Press the REPEAT button one more time at the desired
end point.
Result:
The tape is automatically rewound to the start point.
“INTERVAL REPEAT” is displayed.
EASY OPERATION
ENTER
E D
N:SETUP
AUTO POWER OFF
:OFF
REPEAT PLAY
:OFF
NO. OF
INTERVAL REPEAT : 5
E N
D:SETUP
38
Downloaded From Disc-Player.com Samsung Manuals
39
01274A SV-DVD1E/XEU-GB4
9/5/56 7:59 AM
Page 40
Using the Tape Counter
Connecting an RCA Audio/Video Input Cable
GB
GB
The tape counter:
◆ Indicates the elapsed time in the play and record modes
(hours, minutes and seconds)
◆ Is reset when a cassette is inserted in the DVD-VCR
◆ Allows you to find the beginning of a sequence easily
☛
If the remaining time is to be calculated correctly, you
must indicate the type of cassette being used.
0:00:00
1
2
You can connect other audio/video equipment to your DVD-VCR
using audio/video cables if the appropriate outputs are available on
the equipment chosen.
Examples: ◆ You wish to copy a video cassette with the help of a
second VCR (see page 42).
◆ You wish to play back and/or copy pictures taken
with a camcorder (see page 42).
☛
Insert a cassette in your DVD-VCR.
To set the tape counter to zero at the beginning of a sequence:
Press DISPLAY twice to display the counter
Press CLEARwhen you want to set the tape counter to zero
1
Connect one end of the RCA audio/video cable into the VIDEO
socket on the Rear of the VCR.
2
Plug the other end of the audio/video cable into the appropriate
output connector on the other system (VCR or camcorder).
3
Connect one end of the RCA audio cable into the AUDIO sockets
on the Rear of the VCR.
◆
◆
2
3
2
To fast-forward or rewind to the sequence at which the counter
was set to zero, simply press
or .
Result:
The DVD-VCR stops automatically when the counter
reaches zero.
➢
Some DVD-VCR information, such as the counter, can be
displayed on the television screen (unless you have
deactivated the OSD mode; refer to page 19).
Press DISPLAY:
◆ Once to display the current function, programme
number, recording speed, date, time and counter
◆ Twice to display the counter only
◆ Three times to display the time remaining on the
cassette
◆ Four times to clear the display
40
Downloaded From Disc-Player.com Samsung Manuals
1
◆ Make sure that both the television and the VCR are
switched off before connecting the cables.
➢
4
3
3
Take care to respect the colour coding of the left and right
channels.
Plug the other end of the audio cable into the appropriate output
connectors on the other system (VCR, camcorder or Hi-Fi sound
system).
41
01274A SV-DVD1E/XEU-GB4
9/5/56 7:59 AM
Page 42
Using the Assemble Edit Function
Audio Dubbing a Pre-recorded Cassette
This function allows you to start a new recording at a specific
position on the cassette while maintaining a very smooth scene
change.
GB
2
5
GB
With the Audio Dubbing function, you erase the previously
recorded sound and replace it with a new soundtrack from:
1
Insert the cassette to be edited in your DVD-VCR.
2
Press the
3
When you reach the position from which you wish to start the new
recording, press the ll button.
4
Press the FRAME/STEP (
◆ A CD, DVD
ll button to start playback.
◆ A microphone connected to a sound system
Restriction:
)button again as often as
Audio dubbing is applicable only to the longitudinal audio track
(normal audio).
necessary to advance frame by frame, until the exact recording
position is located.
5
While the DVD-VCR is in still mode, hold the REC button ( I
down for a while to activate the Assemble Edit function.
Result:
Record symbol flashes in the display.
6
Select the source from which you wish to record by pressing:
◆ The PROG( or ) buttons for television channels
◆ The TV VIEW button for the AV1, AV2 or AUX input sources
7
Press the
8
When you have finished recording, press ■ .
)
You can copy a cassette to your SV-DVD1E from another video
source, such as another VCR or a camcorder.
1
6
It is an infringement of copyright laws to copy prerecorded
cassettes or to re-record them in any form without the
permission of the owners of the corresponding copyright.
Connect the DVD-VCR, fromwhich the cassette is to be copied, to
the appropriate SCART audio and video input connectors on the
rear of your DVD-VCR, as indicated on page 12.
2
Insert a blank cassette in your DVD-VCR.
3
Insert the pre-recorded cassette in the other video source (VCR or
camcorder).
4
Press the TV VIEW button to select the appropriate input on your
DVD-VCR:
◆ AV1, AV2 for the SCART input
◆ AUX for the RCA input
7
5
Start playing back the cassette to be copied.
6
Hold REC (I
DVD-VCR.
7
When you have finished recording, press ■ on both VCR and
DVD-VCR.
➢
42
Downloaded From Disc-Player.com Samsung Manuals
1
Connect an RCA audio cable to the appropriate output on your
sound system (cassette player for example).
2
Connect the other end of the RCA audio cable to the audio input
connectors (L, R) on the Rear of your DVD-VCR.
3
Insert the pre-recorded cassette on which the audio track is to be
replaced, and press the ll to start playback.
4
Search for the Audio Dubbing (ending) point using the , and set
the counter to 0:00:00 by pressing CLK/CTR and CLEAR.
5
Search back slightly beyond the Audio Dub start point using the
button.
6
Press the
Press the
7
Press A.DUB.
Result:
Your VCR is now in the Audio dubbing Pause
mode.
8
Press the TV VIEW button to select Audio dubbing source.
ex) If you want to dub external cassette player, then select AUX.
9
On the sound system, locate the point on the cassette at which
you wish to start playback.
Example: The track that you wish to record on the cassette.
10
When you are ready:
◆
Start playback on the sound system
◆
Press the ll on the remote control.
Result:
The soundtrack is replaced on the pre-recorded cassette.
11
The audio dubbing will finish when the counter reaches 0:00:00.
ll button to start recording.
Recording from Another VCR or Camcorder
☛
◆ A cassette player
) down for a while to start recording on your
➢
2
2
ll button.
ll button one more time to make PAUSE mode.
7
A.DUB
-0:05:23
The new sound will be recorded on the normal sound
track of the tape, and the original sound will remain on
the Hi-Fi sound track.
To hear the new sound and original sound mixed
together, press the Audio button on the remote control
until the MIX option is displayed (see page 35).
If you wish to view the cassette being copied:
◆ Your SV-DVD1E must be connected as usual to the
television (see page 11 for further details)
43
01274A SV-DVD1E/XEU-GB4
9/5/56 7:59 AM
Page 44
Disc Type and Characteristics
SQPB (Super VHS Quasi Playback)
GB
GB
This function is for playback of Super VHS format tapes only, not
for recording.
3
1
Inset the SVHS format tape that you want to see.
2
Press PLAY ( ll ) to start playing the cassette.
3
Press SVHS (
☛
) button to start SQPB.
This DVD player is capable of playing the following types of discs with the corresponding logos :
Disc Types
(Logos)
DVD
12 Cm
Audio
+
Video
If the SQPB is on during normal playback, the video
output is distorted.
8 Cm
VIDEO-CD
Auto Power Off
EASY OPERATION
ENTER
1
Press SETUP on the remote control.
Result:
The programming menu is displayed.
2
Press the corresponding ,
EASY OPERATION option.
3
Press the ENTER button to select this option.
Result:
The EASY OPERATION menu is displayed.
4
Press the corresponding
or
buttons, until the cursor is
placed in front of the AUTO POWER OFF option.
5
Press the
interval.
or ,
buttons to select the
E D
N:SETUP
AUTO POWER OFF
:OFF
REPEAT PLAY
:OFF
NO. OF
INTERVAL REPEAT : 5
button, until you select the time of Auto Power off
OFF
2HOUR
3HOUR
Characteristics
Single-sided
240 min.
Double-sided
480 min.
Single-sided
80 min.
Double-sided
160 min.
• DVD contains excellent sound
and video due to Dolby Digital
and MPEG-2 system.
• Various screen and audio
functions can be easily selected
through the on-screen menu.
12 Cm
Audio
+
Video
The Auto Power Off feature automatically turns off your DVD-VCR
if no signal is received and you do not press any button for the
selected time.
Max.
Playing
Time
Recording Disc Size
Types
AUDIO-CD
74 min.
• Video with CD sound, VHS
quality & MPEG-1 compression
technology.
8 Cm
20 min.
12 Cm
74 min.
8 Cm
20 min.
Audio
• An LP is recorded as an analog
signal with more distortion. CD
is recorded as a Digital Signal
with better audio quality, less
distortion and less deterioration
of audio quality over time.
* DO NOT play CD-ROM, CD-I, CD-R and DVD-ROM in this player!
(CDGs play audio only, not graphics.)
Disc Markings
~
• Playback
Region
Number
PAL
• PAL broadcast
system in U.K,
France, Germany,
etc.
STEREO
• Dolby
Digital disc
• Stereo
disc
DIGITAL
SOUND
• Digital
Audio disc
• DTS disc
E N
D:SETUP
6
On completion, press SETUP twice to exit the menu.
Playback Region Number
Both the DVD player and the discs are coded by region. These regional codes must match in order for the
disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is described on the rear panel of the player.
44
Downloaded From Disc-Player.com Samsung Manuals
45
01274A SV-DVD1E/XEU-GB4
9/5/56 7:59 AM
Page 46
Playing a Disc
Choosing a Connection
GB
GB
Before Playback :
◆ Turn on a TV and press the TV/VIDEO button to select
video mode.
The following show examples of connections commonly used to connect the DVD player with a TV
and other components. It is only available for DVD. The DVD-VCR out can not watch by this
connection.
Connection of S-Video Jack
Connection to an Audio System
◆ Turn on your Audio System and select AUX, CD or DVD.
◆ Refer to your AUDIO User’s Manual.
1
Press the OPEN/CLOSE button.
The STANDBY indicator light goes out and the tray opens.
2
Place a disc gently into the tray with the disc’s label facing up.
3
Press the ll (PLAY/PAUSE) button or OPEN/CLOSE button to
close the disc tray.
1,3
☛ When
RESUME function :
you stop disc play, the player remembers where you
3
stopped, so when you press PLAY again, it will pick up
where you left off (unless the disc is removed, the STOP
button is pressed twice or the player is unplugged.).
Dolby Digital Decoder
Digital Audio Input Jack
➢
TV
S-Video
Cable
➢
◆ If the player is left for 2 minutes in pause mode, it will
stop.
◆ This
icon indicates an invalid button press.
Before using the DVD operation, press the TV VIEW
button on the remote control to watch and select DVD.
OR
SV-DVD1E
Digital Audio out
Jack
46
Downloaded From Disc-Player.com Samsung Manuals
S-Video Jack
47
01274A SV-DVD1E/XEU-GB4
9/5/56 7:59 AM
Page 48
Playing a Disc
Using the Search & Skip Functions
GB
1
Stopping Playback. Press the STOP button during playback.
2
Removing Disc. Press the OPEN/CLOSE button.
3
Pausing Playback.
Press the
ll (PLAY/PAUSE) button on the remote during
playback.
◆ Screen stops, no sound.
◆ To resume again, press ll (PLAY/PAUSE) button once
again.
3
4
5
5
5
Step Motion Playback (Except CD)
Press the STEP button on the remote during pausing playback.
◆ Each time the button is pressed, a new frame will appear.
◆ No sound is heard during STEP mode.
◆ Press ll (PLAY/PAUSE) to resume normal playback.
(You can only perform step motion playback in the forward
direction.)
Slow Motion Playback (Except CD)
Press the
button on the remote during PAUSE or STEP mode.
◆ By pressing the
button, you can select slow motion
,
playback for 1/2, 1/4 or 1/8 of normal speed.
◆ No sound is heard during slow mode.
◆ Press ll (PLAY/PAUSE) to resume normal playback.
◆ When playing, the reverse slow motion playback will not
work.
1
2
During playback, press the
button on the remote.
or
◆ Press the
button on the remote and press again to
or
search at a faster speed(2X/4X/8X/16X/32X/normal speed, in
order) on the DVD.
◆ Press the
button on the remote and press again to
or
search at a faster speed(4X/8X/normal speed in order) on
VCD and CD.
◆ To return to normal speed playback, press the ll
(PLAY/PAUSE) button.
Downloaded From Disc-Player.com Samsung Manuals
1
1
During playback, press the I (NEXT SKIP) or I (BACK SKIP)
button.
◆ When playing a DVD, if you press the I (NEXT SKIP)
button, it moves to next chapter. If you press the I (BACK
SKIP) button, it moves to the beginning of the chapter. One
more press makes it move to the beginning of the previous
chapter.
◆ When playing a VCD 2.0 in MENU OFF mode, a VCD 1.1 or
a CD, if you press the I (NEXT SKIP) button, it moves to
next track. If you press the I (BACK SKIP) button, it moves
to the the beginning of the track. One more press makes it
move to the beginning of the previous track.
◆ If a track exceeds 15 minutes when playing a VCD and you
press the I (NEXT SKIP) button, it moves forward 5
minutes. If you press the BACK SKIP button, it moves
backward 5 minutes.
◆ When playing a VCD 2.0 in the MENU MODE or Track View
function, if you press the I (NEXT SKIP) button, it moves to
the next MENU or the next Track View display. If you press
the I (BACK SKIP) button, it moves to the previous MENU
or the previous Track View display. (See page 53.)
➢
48
GB
During playback, you can search quickly through a chapter or track
or use the skip function to jump to the next selection.
2
◆ When in search mode (8X/16X/32X) on a DVD or
high-speed playback on a VCD, no sound will be
heard.
◆ When 2X SCAN AUDIO is set to ON in the SETUP
MENU, no sound will be heard on discs which are
recorded with LPCM, DTS or MPEG-2.
◆ Depending on the disc, audio may not be heard when
a disc is in 2X playback mode.
49
01274A SV-DVD1E/XEU-GB4
9/5/56 7:59 AM
Page 50
Using the Display Function (DVD)
GB
DVD T:01
ENG 5.1 CH
1
During playback, press the DISPLAY button on the remote.
- Current title, chapter number and elapsed time will be displayed.
◆ Use the , button to select a title or a chapter number.
Use the , button or Number buttons to enter a different
title or chapter number, then press the ENTER button.
◆ To enter the time from which you want to start, use the ,
button to select, then use the Number buttons to enter the
time. Then press the ENTER button.
2
Press the DISPLAY button on the remote twice.
- Current audio, subtitle and volume control will appear.
- To make the screen disappear, press the DISPLAY button again.
C:04 0:06:54
ENG ON
Using the Display Function (CD/VCD)
1
CD
T:01
0:06:54
During playback, press the DISPLAY button on the remote.
- Current track number, elapsed time and volume control will be
displayed.
◆ Use the , button to select a track. Use the , button or
Number buttons to enter a different track number, then press
the ENTER button.
◆ To enter the time from which you want to start, use the ,
button to select, then use the Number buttons to enter the
time. Press the ENTER button.
- To make the screen disappear, press the DISPLAY button again.
➢
50
Downloaded From Disc-Player.com Samsung Manuals
What is a Chapter?
Each Title on a DVD can be divided into chapters (similar
to tracks on an audio CD).
What is a Title?
A DVD may contain several different titles. For example,
if a disc contains four different movies, each might be
considered a title.
01274A SV-DVD1E/XEU-GB5
9/5/56 7:57 AM
Page 51
Repeat Play
GB
Repeat the current track, chapter, title, a chosen section (A-B), or
all of the disc (VCD/CD only).
When Playing a DVD :
1
2
Press the REPEAT button on the remote. Repeat screen appears.
Select Chapter, Title or A-B using the , button.
- A-B Repeat
Press the REPEAT button. Select A-B on screen with the ,
button. Or press the A-B button on the remote.
◆ Press ENTER at the point where you want the repeat play to
start (A). The B is automatically highlighted.
◆ Press ENTER at the point where you want the repeat play to
stop (B).
◆ The A-B Repeat that you set plays until you turn Repeat off.
◆
3
Press ENTER.
4
To return to normal playback press REPEAT again, then press the
, button to select Off and press ENTER.
➢
◆ DVD repeats playback by chapter or title, CD and
VCD repeat playback by disc or track.
◆ Depending on the disc, the Repeat function may not
work.
◆ If the title or track is completed before marking the
end (B), the end of title or track becomes B
automatically.
◆ When in VCD 2.0 mode (MENU ON mode), this
function does not work.
1
DVD
Off Chapter Title A-B
VCD/CD
Off Track Disc
51
Downloaded From Disc-Player.com Samsung Manuals
A-B
01274A SV-DVD1E/XEU-GB5
9/5/56 7:57 AM
Page 52
Program Play (DVD/VCD/CD)
Using the Disc View Function (Track View VCD)
GB
GB
Displays the beginning view of each track and the track number.
DVD
PROGRAM 01
Chap. (T:01)
Program Order
01 -- -- --- -- -- --- -- -- --- -- -- --- -- -- --
01 02 03 04
05 06 07 08
09
1
Press the MODE button.
1
During playback, press the TITLE button.
2
Use the
button.
2
Press the
button.
,
button to select PROGRAM. Press the ENTER
3
Use the , button to select the first chapter (or track) to add to
the program. Press the ENTER button. The selection numbers
appear in the Program Order box.
4
Press the ll (PLAY/PAUSE) button. The disc will be played
back in programmed order.
,
DISC VIEW
ENTER
button to select TRACK VIEW. Press the ENTER
1 Track View
3
Select the desired view by pressing the
4
Press the ENTER button.
,
or ,
2 Index View
buttons.
VCD/CD
TRACK VIEW
PROGRAM 01
Track
Program Order
01 -- -- --- -- -- --- -- -- --- -- -- --- -- -- --
01 02 03 04
05 06 07 08
09
01
02
03
04
05
06
07
08
09
(example)
Using the Disc View Function (Index View VCD)
Random Playback (DVD/VCD/CD)
Displays the equally divided 9 views of the current playing track.
1
Press the MODE button.
2
Use the , button to select RANDOM. Press the ENTER button.
The disc will be played back in random order.
➢
1
52
Downloaded From Disc-Player.com Samsung Manuals
◆ Depending on the disc, the Program and Random
Playback function may not work.
◆ When in VCD 2.0 mode (MENU ON mode), these
functions do not work.
◆ To resume normal playback, press the CLEAR button.
1
During playback, press the TITLE button.
2
Press
button.
3
Select the desired view by pressing
4
Press the ENTER button.
➢
,
button to select INDEX VIEW. Press the ENTER
,
or ,
buttons.
INDEX VIEW
01
02
03
04
05
06
07
08
09
(example)
◆ In stop mode on VCD, press the TITLE button and
the TRACK VIEW will be displayed.
◆ When pressing the TITLE button with a DVD; the
disc’s TITLE MENU function comes up. A disc must
have at least two titles for the TITLE MENU function
to work.
◆ When pressing the TITLE button with a CD; the unit
enters the INTRO mode. INTRO lets you listen to the
beginning of each track for about 10 seconds.
1
53
01274A SV-DVD1E/XEU-GB5
9/5/56 7:57 AM
Page 54
Selecting the Audio Language (Using the AUDIO button)
Changing the Camera Angle
GB
GB
You can select a desired language quickly and easily with the
AUDIO button.
1
Press the AUDIO button.
2
Use the , button to select the desired language on a DVD.
- The audio and subtitle languages are represented by
abbreviations.
1
3
Use the
,
button to select STEREO, R CHANNEL or L
CHANNEL. (On VCD/CD)
When a DVD contains multiple angles of a particular scene, you
can select the Angle function.
Using the ANGLE button :
Check to see if an ‘ANGLE (
)’ mark is present at the upper
right hand corner of the screen.
1
When an ‘ANGLE’ mark is shown, press the ANGLE button.
2
Use the
,
button to select the desired screen angle. Then
press the ENTER button.
3
To turn off the display, press the ANGLE button again.
4/4
(example)
ENG DOLBY DIGITAL 5.1CH
1
STEREO
Selecting the Subtitle Language
(Using the SUBTITLE button)
You can select a desired subtitle quickly and easily with the
SUBTITLE button.
1
ENG
Off
ENG
On
1
Press the SUBTITLE button.
2
Use the
3
Use the , button to determine whether or not the subtitle will
be displayed.
- Initially, the subtitling will not appear on screen.
- The audio and subtitle languages are represented by
abbreviations.
➢
54
Downloaded From Disc-Player.com Samsung Manuals
,
button to select the desired subtitle language.
◆ This function depends on what languages are
encoded on the disc and may not work with all
DVDs.
◆ A DVD disc can contain up to 32 subtitle languages.
55
01274A SV-DVD1E/XEU-GB5
9/5/56 7:57 AM
Page 56
Using the Mark Function (DVD/VCD)
Using the Zoom (DVD/VCD)
GB
GB
The Mark function lets you select parts of a DVD or VCD (MENU
OFF mode) so that you can quickly find the section at a later time.
---
ENTER
1
During playback, press the MARK button on the remote. A marker
will be displayed.
2
Use the ,
3
When you reach the scene you want to mark, press the ENTER
button. The icon will change to a number (1, 2, or 3).
4
Press the MARK button to turn off the display.
button to move to the desired bookmark icon.
1
During playback or pause mode, press the ZOOM button on the
remote. A square will be displayed on screen.
2
Use the , or
want to zoom.
3
Press the ENTER button.
- During DVD playback, press ENTER to zoom in 2X/4X/normal in
order.
- During VCD playback, press ENTER to zoom in 2X/normal in
order.
PLAY
CLEAR
3D Sound Function
1
During playback, press the MARK button on the remote.
2
Use the ,
3
Press the
button to select a marked scene.
ll (PLAY/PAUSE) button to skip to the marked scene.
The simulated surround effect (SPATIALIZER N-2-2) depends on
the disc contents. If you connect the unit to your stereo system,
you can enhance sound quality and produce a greater surround
effect.
This feature is useful when you are using the DVD player with a
two channel stereo through the analog outputs.
(Discs which are recorded with LPCM or DTS will not work.
When the DOLBY DIGITAL OUT or MPEG-2 DIGITAL OUT are
set to BITSTREAM in the SETUP MENU, the 3D Sound function
will not work.)
1
During playback, press the 3D SOUND (
) button. The 3D
SOUND mark will be displayed on screen. (Be sure the DOLBY
DIGITAL OUT or MPEG-2 DIGITAL OUT are set to PCM.)
2
Press the
Clearing a Mark
1
During playback, press the MARK button on the remote.
2
Use the
delete.
3
Press the CLEAR button to delete a bookmark number.
Press the MARK button to turn off display.
1
➢
56
Downloaded From Disc-Player.com Samsung Manuals
,
button to select the part of the screen you
1
Recalling a Marked Scene
1--
,
button to select the bookmark number you want to
➢
,
Off
button to turn the 3D Sound feature on or off.
◆ 3D Sound is possible only on discs recorded using
DOLBY SURROUND or DOLBY DIGITAL. However,
some of these discs do not contain rear channel
sound signals.
◆ Depending on the disc, the Zoom and 3D Sound
function may not work.
◆ Up to three scenes may be marked at the same time.
◆ When in VCD 2.0 mode (MENU ON mode), this
function does not work.
◆ Depending on the disc, the Bookmark function may
not work.
57
01274A SV-DVD1E/XEU-GB5
9/5/56 7:57 AM
Page 58
Using the Setup Menu
Setting Up the Language Features
GB
GB
SETUP MENU
1 Player Menu
2 Disc Menu
English
English
3
4
5
6
7
English
Automatic
Unlocked
Audio
Subtitle
Parental
Audio Options
Display Options
The Setup menu lets you customize your DVD player by allowing
you to select various language preferences, set up a parental level,
even adjust the player to the type of television screen you have.
1
Setup of the Display. Language (See page 59)
Use the Player preference menu to select the
language for the player’s on-screen displays.
DISC MENU ➁
Setup of the Menu Language (See page 59)
Use the Menu preference menu to select the
language you want a DVD’s disc menu to be
displayed in.
➂
AUDIO
➃
Setup of the Subtitle Language (See page 60)
Use the Subtitle preference menu to select the
language the disc’s subtitles are to be displayed
in.
PARENTAL
➄
Setup of the Parental Level (See page 61)
Allows users to set the level necessary to prevent
children from viewing unsuitable movies such as
those with violence, adult subject matter, etc.
AUDIO OPTIONS
DISPLAY
OPTIONS
58
Downloaded From Disc-Player.com Samsung Manuals
➅
With no disc playing, press the SETUP button.
SETUP MENU
2
Use the
,
,
button to select the PLAYER MENU.
3
Press the ENTER button.
4
Use the
5
Press the ENTER button.
- ENGLISH is selected and the screen returns to SETUP MENU.
- To make the SETUP MENU disappear, press the RETURN
button.
,
1
2
3
4
5
6
7
Player Menu
English
Disc Menu
Audio
Subtitle
Parental
Audio Options
Display Options
English
English
AUTOMATIC
UNLOCKED
button to select ‘ENGLISH’.
PLAYER MENU LANGUAGE
1
2
3
4
5
6
English
Francais
Deutsch
Español
Italiano
Nederlands
Using the Disc Menu Language
Setup of the Audio Options (See page 61)
Setup of the Display Options (See page 62)
Use to select which type of screen you want to
watch and several display options.
➆
Use the
features.
button on the remote to access the different
Press the ENTER button to access the sub features.
To make the setup screen disappear after setting up, press the
SETUP button again.
➢
1
Setup of the Audio Language (See page 60)
Use the Audio preference menu to select the
soundtrack language.
SUBTITLE
3
e.g Setting up in ENGLISH.
With no disc playing, press the SETUP button on the remote.
PLAYER MENU ➀
2
If you set the player menu, disc menu, audio and subtitle language
in advance, it will come up automatically every time you watch a
movie.
Using the Player Menu :
Depending on the disc, some Setup Menu selections
may not work.
This function changes the language only for the text on the disc
menu screens.
1
With no disc playing, press the SETUP button.
2
Use the
3
Press the ENTER button.
4
Use the , button to select ‘ENGLISH’.
- Select “OTHERS” if the language you want is not listed.
5
Press the ENTER button.
- ENGLISH is selected and the screen returns to SETUP MENU.
,
e.g Setting up in ENGLISH.
button to select DISC MENU.
DISC MENU LANGUAGE
1
2
3
4
5
6
7
English
Francais
Deutsch
Español
Italiano
Nederlands
Others
59
01274A SV-DVD1E/XEU-GB5
9/5/56 7:57 AM
Page 60
Setting Up the AUDIO Language Features
Setting Up the Parental Control
GB
GB
Using the Audio Language :
AUDIO LANGUAGE
1
2
3
4
5
6
7
8
English
Français
Deutsch
Español
Italiano
Nederlands
Original
Others
1
With no disc playing, press the SETUP button.
2
Press the
3
Press the ENTER button.
4
Press the , button to select ‘ENGLISH’ .
- Select “ORIGINAL” if you want the default soundtrack language
to be the original language the disc is recorded in.
- Select “OTHERS” if the language you want is not listed.
5
Press the ENTER button.
- ENGLISH is selected and the screen returns to SETUP MENU.
,
button to move to AUDIO.
The Parental Control function works in conjunction with DVDs that
have been assigned a rating - which helps you control the types of
DVDs that your family watches. There are up to 8 rating levels on a
disc.
1
With no disc playing, press SETUP. The Setup Menu screen
appears.
2
Use , to select Parental. Press ENTER. The Parental Control
screen appears.
3
Use , to select Yes if you want to use a password. Press
ENTER. The Enter Password screen appears.
4
Enter your password. The Re-enter Password screen appears to
confirm the password. Enter your password again. The Parental
Control screen appears.
5
Using the Subtitle Language
1
With no disc playing, press the SETUP button.
2
Use the
3
Press the ENTER button.
4
Use the , button to select ‘ENGLISH’.
- Select “AUTOMATIC” if you want the subtitle language to be the
same as the language selected as the audio preference.
- Select “OTHERS” if the language you want is not listed. Some
discs may not contain the language you select as your initial
language; in that case the disc will use its original language
setting.
,
button to select SUBTITLE.
6
PARENTAL CONTROL
1
No
CREATE PASSWORD
Enter Password
____
About the Rating Level ;
The Rating Level will work only when Use Password is set to Yes.
To unlock the player, use , to select No. Use
, to select Rating level. Press ENTER.
- Use , to select the level(e.g. Level 6) and press
ENTER. The disc that contains Level 7 will now not play.
- To cancel the rating level, use , to select No in Use
Password.
About the Change Password ;
- Use , to select Change Password. The Change
Password screen appears.
- Enter your new password. Re-enter the new password again.
Use Password
PARENTAL CONTROL
1
2
3
Use Password
Rating Level
Change Password
Yes
1
SUBTITLE LANGUAGE
1
2
3
4
5
6
7
8
Automatic
English
Français
Deutsch
Español
Italiano
Nederlands
Others
5
Press the ENTER button.
- ENGLISH is selected and the screen returns to SETUP MENU.
➢
60
Downloaded From Disc-Player.com Samsung Manuals
➢
◆ How to make the SETUP MENU disappear or return
to menu screen during set up; Press RETURN button.
◆ If you have forgotten your password, see Forget
Password in the Troubleshooting Guide.
e.g
Setting up in LEVEL 6
RATING LEVEL
Level 8 Adult
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
Level 1 Kids Safe
◆ If the selected language is not recorded on the disc,
the original pre-recorded language is selected.
◆ How to make the SETUP MENU disappear or return
to menu screen during set up; Press RETURN button.
61
01274A SV-DVD1E/XEU-GB5
9/5/56 7:57 AM
Page 62
Setting Up the Audio Options
Setting Up the Display Options
GB
GB
1
With no disc playing, press the SETUP button.
1
With no disc playing, press the SETUP button.
2
Use the , button to select AUDIO OPTIONS. Then press the
ENTER button.
2
Use the
, button to select DISPLAY OPTIONS. Then press
the ENTER button.
3
Use the ,
button.
3
Use the ,
button.
DISPLAY OPTIONS
AUDIO OPTIONS
1 Dolby Digital Out
PCM
2 MPEG-2 Digital Out
PCM
3 DTS
Off
4 Dynamic Compression
On
5 2X Scan Audio
Off
button to select the desired item. Then press the
,
❶ DOLBY DIGITAL OUT / ❷ MPEG-2 DIGITAL OUT
1
2
PCM : Converts to PCM(2CH) 48kHz/16Bit audio. Select
PCM when using the Analog Audio Outputs.
BITSTREAM : Converts to Dolby Digital
BITSTREAM - 5.1CH (in case of MPEG-2, 7.1CH). Select
BITSTREAM when using the Digital Audio Output.
1
2
3
❸ DTS
2
ON : Outputs DTS BITSTREAM via digital output only.
Select DTS when connecting to a DTS DECODER.
OFF : Doesn’t output digital signal.
1
2
➢
62
Downloaded From Disc-Player.com Samsung Manuals
ON : Turns 2X audio on.
OFF : Turns 2X audio off.
Though 2X SCAN AUDIO is ON in the SETUP MENU, no
sound will be heard on discs which are recorded with
LPCM, DTS or MPEG-2.
4:3 LETTER BOX : Select when you want to see the
total 16:9 ratio screen DVD supplies, even though you
have a TV with a 4:3 ratio screen. Black bars will appear at
the top and bottom of the screen.
4:3 PAN-SCAN : Select this for conventional size TVs
when you want to see the central portion of the 16:9
screen. (Extreme left and right side of movie picture will be
cut off.)
16:9 WIDE : You can view the full 16:9 picture on your
widescreen TV.
❷ STILL MODE
1
❹ DYNAMIC COMPRESSION
1 ON : To select dynamic compression.
2 OFF : To select the standard range.
❺ 2X SCAN AUDIO
,
❶ TV ASPECT
NOTE : Be sure to select the correct Digital Output or no
audio will be heard.
1
button to select the desired item. Then press the
1 TV Aspect
2 Still Mode
3 Screen Messages
4 Black Level
5 Quasi-PAL
6 VIDEO Output
2
3
FIELD : Select this feature when the screen shakes in the
AUTO mode.
FRAME : Select this feature when you want to see small
letters more clearly in the AUTO mode.
AUTO : When selecting AUTO, FIELD/FRAME mode will
be automatically converted.
❸ SCREEN MESSAGES
Use to turn on-screen messages on or off.
❹ BLACK LEVEL
Adjusts the brightness of the screen.
❺ QUASI-PAL
◆ How to make the SETUP MENU disappear or return
to menu screen during set up; Press RETURN button.
◆ Certain audio features of this product manufactured
under a license from Desper Products, Inc.
Spatializer® and circle-in-square device are
trademarks owned by Desper Products, Inc.
◆ Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories. Confidential unpublished works.
©1992-1997 Dolby Laboratories Inc. All rights
reserved.
◆ “DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
Depending on a disc, you can play a NTSC DVD disc by
Quasi-PAL mode.
❻ VIDEO OUT
1
2
3
➢
RGB : Sends RGB signal to the AV JACK(SCART
terminal).
VIDEO : Sends COMPOSITE VIDEO signal to the
AV JACK(SCART terminal).
S-VIDEO : Sends S-VIDEO signal to the S-JACK.
◆ How to make the SETUP MENU disappear or return
to menu screen during set up; Press RETURN button.
63
4:3 L-Box
Auto
On
Off
Off
RGB
01274A SV-DVD1E/XEU-GB5
9/5/56 7:57 AM
Page 64
Technical Specifications
Problems and Solutions (VCR)
GB
GB
Before contacting the Samsung after-sales service, perform the following simple checks.
Problem
General
Rated voltage
AC100 - 240V, 50/60Hz
Power consumption
32Watts
Output
You cannot insert a video cassette
◆
A video cassette can only be inserted with the window
side up and the safety tab facing you.
The television programme was not recorded
◆
◆
◆
Check the DVD-VCR aerial connections.
Is the DVD-VCR tuner properly set?
Check if the safety tab is intact on the cassette.
Timer recording was unsuccessful
◆
◆
◆
Was the STANDBY/ON button pressed to activate the timer?
Re-check the recording start/stop time settings.
If there was a power failure or interruption during timer
recording, the recording will have been cancelled.
5.6Kg
430mm X 357mm X 100mm
Operating ambient temperature
+5°C ~ +35°C
Installation conditions
Operation position : Horizontal,
Video input (Rear)
RCA jack : 1.0Vp-p (unbalanced) 75Ω
Audio input (Rear)
RCA jack :-8dBm, 47Kohm unbalanced
RF out
UHF 21-69 (Initial CH60)
Headphones, RCA jack, Euro Scart socket
No playback picture or the picture
is distorted
◆
Audio (DVD, VCR)
Check to see if you are using a prerecorded tape.
Audio (DVD only)
Digital audio out (OPTICAL, COAXIAL)
You cannot see normal broadcasts
◆
Video (DVD, VCR)
RCA jack, Euro Scart socket
Video (DVD only)
S-Video out
Check the TUNER/EXTERNAL setting. It should be on
TUNER.
Check the TV/VCR aerial connections.
◆
Noise bars or streaks on playback
◆
Press the TRK (+or -) buttons to minimize this effect.
◆
A still picture may have “noise bars”, depending on the
condition of the tape. Press the TRK (+or -) buttonsduring
SLOW motion to minimize this effect.
If poor pictures appear on a variety of cassettes, the video
heads may need cleaning. This is not a common problem
and unless it appears, the heads should not be cleaned.
When cleaning the video heads, read all instructions
provided with the head cleaning cassette. Incorrect head
cleaning can permanently damage the video heads.
S-VHS type video tape (Playback only)
When the II button is pressed
during playback, the still picture
has severe “noise bars” streaks
Color system
PAL, NTSC4.43, NTSC playback on PAL TV
Video Head Cleaning
◆
Tuning system
I
Video S/N
Above 43dB (standard recording)
If when tuning in your TV to the DVD-VCR
test pattern your TV does not find the test
pattern or the pattern when found suffers
from interference, it may be due to the
DVD-VCR output channel clashing with
the normal TV transmissions in your area.
To prevent this you will need to change the
DVD-VCR output channel in the following
way
1. Remove the aerial input plug from the socket marked (aerial
symbol) on the rear of the DVD-VCR.
2. Carry out the instructions “Tuning Your Television for the DVDVCR” (see page 14).
3. Carry out the instructions “Setting the DVD-VCR output
Channel” (see page 19), move the channel number
several channels down from the original setting.
(example:from 60 to 57).
4. Replace the aerial plug into the socket marked (aerial symbol)
on the rear of the DVD-VCR.
5. Re-tune your TV to the DVD-VCR again by following
instructions “Tuning Your Television for the DVD-VCR”
(page 14).
6. If the problem still exists repeat steps 1 to 5 moving several
more channels away from the original setting.
Tape format
DVD
Check that the power plug is connected to a wall outlet.
Have you pressed the STANDBY/ON button?
Size
RGB out : Euro Scart socket
VCR
◆
◆
Weight
Relative humidity :Below 75%
Input
Explanation/Solution
No power
VHS type video tape,
Resolution
Above 240 lines (standard recording)
Audio S/N
Above 68dB (Hi-Fi), 39dB (Mono)
Audio frequency characteristics
20Hz - 20KHz (Hi-Fi)
Disc
DVD, CD (12cm), CD(8cm), VIDEO-CD (12cm)
Audio S/N
115dB
Audio dynamic range
105dB
If you are unable to solve the problem after reading the above instructions, note:
◆ The model and serial number on the rear of your DVD-VCR
◆ The warranty information
◆ A clear description of the problem
Then contact your nearest SAMSUNG after-sales service.
64
Downloaded From Disc-Player.com Samsung Manuals
65
01274A SV-DVD1E/XEU-GB5
9/5/56 7:57 AM
Page 66
SAMSUNG ELECTRONICS (UK) LTD
AUTHORISED SERVICE CENTERS
Troubleshooting Guide (DVD)
In the event of warranty service being required, please contact your retailer first. If they cannot provide service, please contact
your nearest service centre listed below. Service facilities are return to base, however some agents may provide an in-home
service (there may be a cost for call out). Please refer to your warranty card or retailer for terms and conditions of the warranty.
GB
Before requesting service (troubleshooting)
Problem
Disc does not play.
5.1 channel sound is not
being reproduced.
AVON
Action
Page
◆
◆
◆
Ensure that the disc is installed with the label side facing up.
Check the region number of the DVD.
This player cannot play CD-ROMs, DVD-ROMs, CD-R, etc. Insert a
DVD, a VIDEO-CD or a CD.
P45
◆
5.1 channel sound is reproduced only when the following conditions
are met. :
1)The DVD-VCR player is connected with the proper amplifier
2) The disc is recorded with 5.1 channel sound.
Check whether the disc being played has the “Dolby 5.1 ch” mark on
the outside.
Check if your audio system is connected and working properly.
◆
◆
◆
The
icon appears on
screen.
P58-63
Some of the functions selected in the Setup Menu may not work
properly if the disc is not encoded with the corresponding function.
The screen ratio cannot be
changed.
◆
The Screen Ratio is fixed on your DVDs.
◆
Forgot password
◆
If you experience other
problems.
◆
Make sure you have selected the correct Digital Output in the Audio
Options Menu.
Press power on from a cold start with no disc in the unit. Press the
and
ll buttons simultaneously on the front panel for five
seconds. The Select Menu Language display will appear. Select the
desired language button. Press the SETUP button on the remote
control to select the Parental Mode. The Parental Mode is now
unlocked as indicated on the display. Press the DOWN button to
select Parental. Press ENTER and the Create Password display will
appear. You can now set your rating level and change your
password to a new number.
Go to the contents and find the section of the instruction book that
contains the explanations regarding the current problem, and follow
the procedure once again.
If the problem still cannot be solved, please contact your nearest
authorized service center.
BERKSHIRE
READING
A & W SOUND & VISION
TEL: 01734 872000
MAIDENHEAD
J F ASSOCIATES
TEL: 01628 25709
WARGRAVE
J F ASSOCIATES
TEL: 01734 401525
CAMBRIDGESHIRE
DRY DRAYTON
DRAYTON ELECTRONICS
TEL: 01954 211330
PETERBOROUGH
DEEPING TV SVCS
TEL: 01778 343831
CHESHIRE
CHESTER
H & H VIDEO & TV
TEL: 01244 379579
WARRINGTON
W L ELECTRONICS
TEL: 01925 764387
P49-52
P54-58
◆
◆
P46
The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is
out of range.
Playback mode differs from
the Setup Menu selection.
No audio.
ESSEX
BRISTOL
GOGGLEBOX TV
TEL: 01275 838083
P63
P62
CORNWALL
BUDE
H B H WOOLACOTTS
TEL: 01288 352269
LAUNCESTON
H B H WOOLACOTTS
TEL: 01566 772096
NEWQUAY
GREENBANK ELECTRONICS
TEL: 01637 880576
WADEBRIDGE
H B H WOOLACOTTS
TEL: 01208 816155
CUMBRIA
BARROW IN FURNESS
KENNETH GARDNER
TEL: 01229 821202
SEARLE AUDIO
TEL: 01229 839692
PENRITH
CANNAN & BROWN
TEL: 01768 864829
DEVON
HOLSWORTHY
H B H WOOLACOTTS
TEL: 01409 253280
NEWTON ABBOT
TELLI-SCOPE ELECTRONICS
TEL: 01626 63907
PLYMOUTH
ARGYLE TV & VIDEO
TEL: 01752 779933
CTV ELECTRONICS
TEL: 01752 350950
P61
DORSET
BOURNEMOUTH
M & G ELECTRONICS
TEL: 01202 523771
DURHAM
DURHAM
LEE TECH SVCS
TEL: 0191 371 1300
DARLINGTON
GAZE ELECTRONICS
TEL: 01325 482344
DYFED
CARMARTHEN
ADVANCE CONSUMER
TEL: 01267 236143
ST CLEARS
BEN EVANS & SON
TEL: 01994 231015
ESSEX
BRAINTREE
GWYNNE TV & ELECTRICAL
TEL: 01376 322567
66
Downloaded From Disc-Player.com Samsung Manuals
WICKFORD
CENTRAL SERVICE
TEL: 01268 766333
MID GLAMORGAN
BRIDGEND
BRIDGEND SERVICE
TEL: 01656 663463
GLOUCESTERSHIRE
TEWKESBURY
SWITCH ELECTRONICS
TEL: 01684 850063
WESTON-SUB-EDGE
PROFESSIONAL ELECTRONIC
TEL: 01386 841773
HAMPSHIRE
FAREHAM
SOUND & VISION
TEL: 01329 286551
FARNBOROUGH
ICTV
TEL: 01252 510118
PORTSMOUTH
ICTV
TEL: 01705 653654
SOUTHAMPTON
OLYMPIC TV & AUDIO
TEL: 01703 703401
HEREFORD
HEREFORD
J P MICRO SVCS
TEL: 01432 356353
HERTFORDSHIRE
BALDOCK
TECHNICAL REPAIR SVC
TEL: 01462 491144
MARKYATE
TELETECH SVCS
TEL: 01582 841862
NORTH HUMBERISDE
GOOLE
HEADLAND ELECTRCS
TEL: 01977 661223
SOUTH HUMBERSIDE
GRIMSBY
RAYNERS SUPERSTORE
TEL: 01472 358766
KENT
CANTERBURY
BARRETTS OF CANTERBURY
TEL: 01227 766582
DARTFORD
BUDGET REPAIR CENTRE
TEL: 01322 227668
MAIDSTONE
AVERY ELECTRONICS
TEL: 01622 682138
LANCASHIRE
BLACKPOOL
KENNETH GARDNER
TEL: 01253 824047
LANCASTER
KENNETH GARDNER
TEL: 01524 64468
ROCHDALE
CTV SERVICES
TEL: 01706 654983
LEICESTERSHIRE
LEICESTER
SOUNT & VISION CENTRE
TEL: 01162 730444
LINCOLNSHIRE
BRANSTON
STUART WALLACE
TEL: 01522 791496
LONDON
HIGH HOLBORN
BERRYS OF HOLBORN
TEL: 0171 405 1157
LONDON
ARMSTRONG SERVICES
TEL: 0181 523 0023/0051
WEST EALING
BABBER ELECTRONICS
TEL: 0181 579 6315
LONDON
WILLESDEN
ATLANTIC ELECTRIC
TEL: 0181 451 6155
MANCHESTER
ASHTON UNDER LYNE
VIDEOTECH UK
TEL: 0161 308 4092
NORTHENDEN
G H SUMNER LTD
TEL: 0161 998 2705
MERSEYSIDE
ELLESMERE PORT
H & H VIDEO & TV
TEL: 0151 357 1011
LIVERPOOL
P & A AUDIO VIDEO LTD
TEL: 0151 924 7287
MIDDLESEX
HAYES
A & A REPAIRS
TEL: 0181 561 2900/4104
NORFOLK
AYLESHAM
CORTONS ELECTRICAL
TEL: 01263 733391
WATTON
JULIAN HORN
TEL: 01953 881440
NORTHAMPTONSHIRE
KETTERING
INTEGRATED SVCS
TEL: 01536 516475
OXFORDSHIRE
BANBURY
HITECH
TEL: 01295 267415
BOTLEY
SPECTRUM ELECTRON
TEL: 01865 250199
SHROPSHIRE
TELFORD
W OWEN
TEL: 01952 613818
SOMERSET
TAUNTON
ARMTECH ELECTRONICS
TEL: 01823 279401
YEOVIL
M J THOMAS
TEL: 01935 477255
STAFFORDSHIRE
STOKE ON TRENT
TELEFAULTS (S.O.T.) LTD
TEL: 01782 813757
SUFFOLK
IPSWICH
GGN LTD
TEL: 01473 744300
SURREY
WALLINGTON
SERVICECARE
TEL: 0181 669 1145
HORLEY
D K AUDIO VISUAL SVCS
TEL: 01293 786459
EAST SUSSEX
SEAFORD
CLEARVIEW RENTAL & RELAY
TEL: 01323 898989
EASTBOURNE
STARTEC SVCS
TEL: 01323 412012
TYNE & WEAR
NEWCASTLE UPON
TYNE
M SINGH RADIO & TV
TEL: 0191 226 0446
WEST MIDLANDS
COVENTRY
D & J HENRY
TEL: 01203 431393
WEST MIDLANDS
DUDLEY
J S STOREY ELECTRICAL
TEL: 01384 455608
WALSALL
BEAVER ELECTRONICS
TEL: 01922 725554
WARLEY
MERRIVALE TV SVCS
TEL: 0121 544 6273/6350
WILTSHIRE
SWINDON
COLORITE TV LTD
TEL: 01793 641038
WORCESTERSHIRE
WORCESTER
THE HI FI CAR RADIO REPAIR
TEL: 01905 26623
SOUTH YORKSHIRE
SHEFFIELD
GRAPHIC ELECTRONIC SVCS
TEL: 0114 256 2791
BARNSLEY
ALTRA
TEL: 01226 207434
NORTH YORKSHIRE
YORK
DBS SERVICE CENTRE
TEL: 01904 789789
WEST YORKSHIRE
BRADFORD
GRAPHICK ELECTRON
TEL: 01274 862267
HUDDERSFIELD
GRAPHIC ELECTRONICS
TEL: 01484 451045
ILKLEY
R BEAUMONT
TEL: 01943 607021
CHANNEL ISLANDS
GUERNSEY
TELESKILL LTD
TEL: 01481 56508
JERSEY
ALTERNATIVE ELECT
TEL: 01534 68277
ISLE OF WIGHT
AUDIO VISION SVCS
TEL: 01983 752023
NORTHERN IRELAND
CO ARMAGH
CRAIGAVON TV SVCS
TEL: 0762 326119/322505
EIRE
CO CORK
TVAE REPAIRS
TEL: 00353 21 273457
GRAMPIANS
FRASERBURGH
RODGERS ELECTRICAL
TEL: 01346 518540
HIGHLANDS
ULLAPOOL
R & R ELECTRONICS
TEL: 01854 612608
LOTHIAN
EDINBURGH
RETEC AUDIO & VISUAL
TEL: 0131 478 7779
STRATHCLYDE
GLASGOW
DSC ELECTRONICS
TEL: 0141 941 3711
TAYSIDE
DUNDEE
ANCRUM ELECTRONICS
TEL: 01382 454511
67
01274A SV-DVD1E/XEU-GB5
9/5/56 7:58 AM
Page 68
Downloaded From Disc-Player.com Samsung Manuals
01274A SV-DVD1E/XEU-GB5
9/5/56 7:58 AM
Page 70
THIS APPLIANCE IS DISTRIBUTED BY
www.samsungvcr.com
Downloaded From Disc-Player.com Samsung Manuals
AC68-01274A