Miele DA 3180 Technical data

Operating and installation instructions
Cooker hoods
DA 3160
DA 3180
DA 3190
DA 3160 EXT
DA 3190 EXT
To avoid the risk of accidents
or damage to this appliance
it is essential to read these
instructions before it is installed
and used for the first time.
en - GB
M.-Nr. 07 777 490
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Description of the functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Grease filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Fitting and replacing the charcoal filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Changing a halogen lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appliance dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Installation accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Positioning the appliance in the wall housing unit . . . . . . . . . . . . . . . . . . . . . . . . . 25
Attaching the lightshield . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Weight of a lightshield matching existing furniture. . . . . . . . . . . . . . . . . . . . . . 28
Aligning the deflector plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Fitting the grease filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Setting up for extraction mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Setting up for recirculation mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Connection for air extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Condensate trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Silencer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Operation with DSM 400 control module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Connection to a window contact switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Potential free connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Connection to a light switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
2
Caring for the environment
Disposal of the packing
material
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Packaging e.g. cling film, polystyrene
and plastic wrappings must be kept out
of the reach of babies and young
children. Danger of suffocation!
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
Please dispose of it at your local
community waste collection / recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
3
Warning and Safety instructions
This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal injury
and damage to property.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time.
They contain important information
on the safety, installation, use and
maintenance of the appliance.
Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.
Correct application
~ This appliance is not designed for
commercial use. It is intended for use in
domestic households and in similar
working and residential environments
such as:
– Shops
– Offices and showrooms
and by residents in establishments
such as
– Hostels and guesthouses
~ It must only be used as a domestic
appliance to extract vapours and
remove odours from cooking.
4
~ Any other usage is not supported by
the manufacturer and could be
dangerous. Miele cannot be held liable
for damage resulting from incorrect or
improper use or operation of the
appliance.
~ This appliance is not intended for
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
are supervised whilst using it or have
been shown how to use it correctly by a
person responsible for their safety.
Safety with children
~ This appliance is only intended for
use by adults who have read these
instructions.
~ This appliance is not a toy! To avoid
the risk of injury, keep children well
away and do not allow them to play with
it or to use the controls. They will not
understand the potential dangers
posed by it. They should be supervised
whenever you are working in the
kitchen.
~ Older children may use the cooker
hood only when its operation has been
clearly explained to them and they are
able to use it safely, recognising the
dangers of misuse.
~ Please be aware that on cooker
hoods with halogen lighting, the lamps
will get very hot during use and remain
hot for some time after switching off. To
safeguard against burning, keep
children well away from the lamps at all
times.
Warning and Safety instructions
Technical safety
~ Before installation, check the cooker
hood for visible signs of damage.
Under no circumstances should you
use a damaged appliance. It could be
dangerous.
~ Before connecting the appliance to
the mains supply, make sure that the
voltage and frequency details given on
the data plate correspond with the
on-site electricity supply, otherwise the
appliance could be damaged. Consult
a qualified electrician if in any doubt.
~ The electrical safety of this
appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system which complies with current
local and national safety regulations. It
is most important that this basic safety
requirement is present and tested
regularly, and where there is any doubt,
the household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
~ For safety reasons, this appliance
may only be used when it has been
fully installed.
~ Only open the housing as described
in the instructions given in the
installation sheet and in the Cleaning
and care section of this booklet. Under
no circumstances should any other
parts of the housing be opened.
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user, and can
cause operational faults.
~ Installation, maintenance and
repairs may only be carried out by a
Miele authorised person in accordance
with current national and local safety
regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
Ensure that current is not supplied to
the appliance until after maintenance or
repair work has been carried out.
~ Faulty components must only be
replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
~ During installation, maintenance and
repair work, the appliance must be
disconnected from the mains electricity
supply. It is only completely isolated
from the electricity supply when:
– it is switched off at the isolator, or
– the screw-out fuse is removed (in
countries where this is applicable), or
– the mains fuse is disconnected, or
– it is switched off at the wall socket
and the plug withdrawn, or
– the fuse from the fused spur
connection unit is withdrawn.
5
Warning and Safety instructions
~ Do not connect the appliance to the
mains electricity supply by a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).
Using at the same time as other
heating appliances that depend on
the air from the room
Warning - danger of toxic fumes
~ For appliances with an external fan
motor fitted (...EXT models) the
connection of the two units must be
made using the connection cable and
the plug connectors.
These models may only be combined
with a Miele external motor.
~ This appliance may only be used in
mobile installations if a risk assessment
of the installation has been carried out
by a suitably qualified engineer.
~ In areas which may be subject to
infestation by cockroaches or other
vermin, pay particular attention to
keeping the appliance and its
surroundings in a clean condition at all
times. Any damage which may be
caused by cockroaches or other vermin
will not be covered by the guarantee.
~ Great care should be taken when
using the cooker hood at the same time
and in the same room or area of the
house as another heating appliance
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas hobs, cookers or ovens which draw
air in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
When used in extraction mode, with or
without an external motor fitted, the
appliance draws air in from the room in
which it is installed and from
neighbouring rooms.
If there is insufficient air, an
underpressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.
Harmful gases could be drawn out of
the chimney or extraction ducting back
into the room, with potentially fatal
consequences.
6
Warning and Safety instructions
In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the cooker
hood and the heater are in operation
simultaneously, an underpressure of
0.04 mbar (4 pa) is the maximum
permissible in the room.
One of the following technical
measures may be necessary to ensure
safe operation.
– If the only way of ensuring adequate
ventilation is via an open window, a
window contact switch should be
fitted to ensure that the cooker hood
can only operate when the window is
opened sufficiently. A window
contact switch kit is available from
good builders' merchants.
Take care when ventilating the room
through an open window that
ventilation is not impaired by a
closed blind or curtain.
– The cooker hood can be set up to
automatically switch on an air intake
fan or open a motorised inlet flap
when it is switched on.
Ventilation can be maintained by air
inlets which must not be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the cooker hood can
only be switched on when the heating
appliance is switched off or vice versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.
,The overall ventilation condition
of the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder or, for gas, a
qualified gas fitter (GasSafe
registered in the UK) must be
sought.
– The cooker hood can be set up to
automatically switch off a heating
appliance which also depends on
the air from the room when it is
switched on.
The Miele DSM 400 control module
offers the possibility of combining other
components with the cooker hood (see
"Operation with Control module DSM
400").
It is available to purchase as an
optional extra.
If in any doubt , the advice of a
qualified builder, gas fitter (GasSafe
registered in the UK) or electrician
must be sought.
If the hood is being operated in
recirculation mode, the above
restrictions do not apply.
7
Warning and Safety instructions
Correct use
~ Never use an open flame beneath
the cooker hood. To avoid the danger
of fire, do not flambé or grill over an
open flame.
When switched on, the cooker hood
could draw flames into the filter. Fat
particles drawn into the cooker hood
present a fire hazard.
~ When using the cooker hood over a
gas hob, ensure that any burners in use
are always covered by a pan. Switch
the cooking zone off when a pan is
removed, even for a short time.
Regulate the flame so that it does not
burn up the sides of the pan.
Do not allow the pans to overheat
excessively (e.g. when using a wok).
The cooker hood can become
damaged when exposed to excessive
heat.
~ Always switch the cooker hood on
when a cooking zone is in use,
otherwise condensation may collect in
the hood, which could cause corrosion.
~ When cooking with oil or fat, chip
pans and deep fat fryers etc, do not
leave the pans unattended. Never leave
an open grill unattended when grilling.
Overheated oil and fat can ignite and
could set the cooker hood on fire.
8
~ Do not use the cooker hood without
the filters in place. This way you will
avoid the risk of grease and dirt getting
into the appliance and hindering its
smooth operation.
~ The filters should be regularly
cleaned or changed as appropriate.
Saturated filters are a fire hazard. See
"Cleaning and care".
~ The cooker hood can get very hot
during cooking due to heat rising from
the hob.
Do not touch the housing or the grease
filters until the cooker hood has cooled
down.
~ Do not use a steam-cleaner to clean
this appliance. Steam could reach the
electrical components and cause a
short circuit.
Warning and Safety instructions
Correct installation
Accessories
~ Refer to the cooker or hob
manufacturer's instructions as to
whether a cooker hood may be
operated above the cooker/hob.
~ Only use genuine Miele spare parts
~ The minimum safety distances
between the top of the cooker or hob
and the bottom of the cooker hood
given in the "Appliance dimensions"
section of this booklet must be
maintained, unless the hob
manufacturer states that a greater
safety distance is required.
and accessories with this appliance. If
spare parts or accessories from other
manufacturers are used, this will
invalidate the guarantee, and Miele
cannot accept liability.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
If more than one cooking appliance is
fitted beneath the cooker hood, and
they have different minimum safety
distances to the cooker hood, select
the greater distance.
~ Follow the cooker or hob
manufacturer's instructions on the use of
flammable materials over the cooker/hob
when installing a wood or laminate
lightshield onto the cooker hood.
~ Safety regulations prohibit the fitting
of a cooker hood over solid fuel stoves.
~ All ducting, pipework and fittings
must be of non-flammable material.
These can be obtained from the Miele
Spare Parts department or from
builders' merchants.
~ The appliance must not be
connected to a chimney or vent flue
which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
~ If exhaust air is to be extracted into
a chimney or ventilation duct no longer
used for other purposes, seek
professional advice.
9
Guide to the appliance
10
Guide to the appliance
a Exhaust socket ø 150 mm
b Control panel
c Grease filter
d Pull-out deflector plate
e Hob lighting
f Charcoal filter
(extra accessory available to order
for recirculation mode)
g Drop-down lightshield to conceal
control panel
The front of the deflector plate can
be fitted with a lightshield to match
your kitchen furniture.
The DA 3160 and DA 3190 can be
fitted with a DFB 61 or DFB 91
lightshield, available as an optional
accessory.
h On/Off control for the fan
i Controls to select fan power level
j Lighting control
11
Description of the functions
The cooker hood works with
. . . air extraction:
The air is drawn in, cleaned by the
grease filter and then directed outside.
If the on-site ventilation system does
not have a non-return flap, then the
non-return flap supplied with the
appliance must be fitted in the exhaust
socket in the motor unit.
Having a non-return flap fitted in the
ducting ensures that air, once ducted
to the outside, cannot get back into the
room again.
The flap is closed when the cooker
hood is switched off.
When the cooker hood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
. . . air recirculation:
(air recirculation conversion kit
required)
The air is drawn in and cleaned first by
the grease filter and then by a charcoal
filter. The cleaned air is then
recirculated back into the kitchen.
Charcoal filters are available to order
through your Dealer or the Miele Spare
Parts Department or via the internet on
www.miele-shop.com. (See back cover
for contact details and "Technical Data"
for model number).
Before using the cooker hood in
recirculation mode, ensure that the
charcoal filter is in place; see
"Cleaning and care".
. . . an external motor:
(EXT models only)
The EXT models are designed to be
connected to an external motor located
outside the room.
The external motor is connected to the
cooker hood by means of a control
cable, and is operated by the controls
on the cooker hood.
12
Operation
The cooker hood is operated by pulling
out and pushing in the deflector plate.
To switch the fan on
^ Pull out the deflector plate.
The fan will begin to operate at setting II.
For short periods of cooking food with
intensive vapours and a strong aroma,
e.g. when searing meat, you may wish
to select the Intensive Setting "IV".
Pull the deflector plate right out to
achieve optimum extraction and to
prevent unnecessary noise levels.
To switch the fan off
The On/Off indicator lamp and the 2nd
– / + power level indicator lamp will
light up.
If the cooker hood has been
connected to a window contact
switch via the Miele DSM 400 control
module, then the fan cannot be
switched on if the window is shut.
The indicator lamp will flash.
To select a power level
^ Use the – / + controls to select the
power level required.
The indicator lamps show which power
level has been chosen.
Depending on the intensity of the
cooking vapours, levels "I" to "III" are
usually sufficient for normal cooking.
^ Push the deflector plate back in. The
next time the deflector plate is pulled
out, the cooker hood will operate at
power level II again.
or
^ Press the On/Off touch control for the
fan
All the indicator lamps will go out.
To switch the lighting on
^ Pull out the deflector plate.
or
^ Press the touch control for the
lighting again.
When the lighting is switched on, the
indicator lamp lights up.
To switch the lighting off
^ Push the deflector plate back in.
or
^ Press the touch control for the
lighting.
The indicator lamp will go out.
13
Operation
Automatic switch-off of the Intensive
setting
You can set the Intensive setting so that
it only runs for 10 minutes before
reverting automatically to level III.
^ To set this option, both the fan and
the hob lighting must be switched off
and the deflector plate pushed in.
^ Press the – and + touch controls at
the same time for approx. 10
seconds until the first power level
indicator lamp lights up in the
display.
^ Press the + touch control to activate
automatic switch-off.
The indicator lamps for fan power
levels I and IV will now light up
constantly.
Press the – touch control to
deactivate the automatic switch-off
function.
^ Press the On/Off touch control to
confirm.
^ Then press, one after the other,
Safety cut-out
Should the cooker hood be left on, the
fan will switch off automatically after 10
hours. The lighting will remain on.
– the hob lighting touch control,
^ Pressing the On/Off control will
switch the fan back on again.
– then the – touch control, and
– the hob lighting touch control again.
The indicator lamps for fan power levels
I and IV will flash if the automatic
switch-off of the Intensive setting is not
activated.
14
Cleaning and care
Before any cleaning or maintenance
work is carried out, disconnect the
cooker hood from the mains supply.
Ensure that:
– it is switched off at the wall socket
and the plug is withdrawn, or
– the fuse is withdrawn from the
fused spur connection unit, or
– the mains fuse is disconnected ,or
– the screw-out fuse is removed
(in countries where this is
applicable).
A range of Miele branded cleaning and
conditioning agents are available to
order through your Miele Dealer/
Chartered Agent, the Miele Spare Parts
Department or via the internet at
www.miele-shop.com.
Housing
General notes
Warning: The surfaces and controls
are susceptible to scratches and
abrasions. Please observe the
following cleaning instructions.
^ All external surfaces and controls can
be cleaned using warm water with a
small amount of washing-up liquid
applied with a well wrung-out soft
sponge or cloth.
Do not use too much water when
cleaning the controls. Water could
penetrate into the electronics and
cause damage.
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents, e.g.
powder cleaners or cream cleaners
and abrasive sponges, as well as pot
scourers or sponges which have
been used previously with abrasive
cleaning agents. These will damage
the surface material.
Important for appliances with
stainless steel housing
(This infomation does not apply to the
controls).
Stainless steel surfaces can be cleaned
with a proprietary non-abrasive cleaning
agent designed specifically for use on
stainless steel.
To help prevent re-soiling, a
conditioning agent for stainless steel
can also be used. Follow the
instructions on the label, and apply
sparingly with an even pressure in the
direction of the "grain".
^ Wipe the surfaces dry using a soft
cloth.
15
Cleaning and care
Controls
The controls may suffer
discolouration or damage if soiling is
left on them for too long. Remove
soiling straight away.
Observe the General notes on cleaning
earlier in this section.
Do not use stainless steel cleaning
agents on the controls.
Grease filter
The re-usable metal grease filter in the
appliance removes solid particles from
the kitchen vapours (grease, dust, etc)
preventing soiling of the cooker hood.
To avoid a build-up of fat, it should be
cleaned every 3-4 weeks on average,
but sooner if necessary.
An oversaturated filter is a fire
hazard.
Important for DFB aluminium
lightshields
(optional accessory)
Aluminium is affected by the way that
light falls on it, by the surrounding
environment and by the angle you
observe it from.
Aluminium surfaces may suffer
discolouration or damage if soiling is
left on them for too long. Remove
any soiling straight away.
Observe the General notes on cleaning
earlier in this section.
Do not use:
– stainless steel cleaners,
– cleaning agents containing
descaling agents,
^ Grip the front of the deflector plate
together with the grease filter, and
pull outwards as shown.
^ Then pull the filter downwards to
remove.
To avoid damaging the filter or the
hob below, make sure you hold the
filter securely at all times when
handling it.
– dishwasher detergent,
– oven sprays.
^ Press the On/Off control to switch the
fan off.
16
Cleaning and care
Cleaning the grease filters by hand
^ Clean the filters with a soft nylon
brush in a mild solution of hot water
and a small amount of washing-up
liquid.
Do not use undiluted washing up
liquid.
^ When removing the filter for cleaning,
also clean off any residues of oil or
fat from the now accessible housing
to prevent the risk of these catching
fire.
Do not use:
– cleaning agents containing
descaling agents,
– powder cleaners, cream cleaners or
abrasive all-purpose cleaning
agents,
– oven sprays.
Cleaning the grease filters in the
dishwasher
^ Place the filters as upright as
possible in the lower basket, with the
short sides upright, and wash on a
65°C programme, ensuring the spray
arm is not obstructed. If a Miele
dishwasher is being used, select the
Sensor wash programme.
^ Use a mild dishwasher detergent.
^ When putting it back, make sure that
the red plastic guides are at the
front and facing upwards.
^ Replace the grease filter in the front
of the deflector plate, press it
upwards and push it in together with
the deflector plate. It will slide onto
the fixing pins at the back. Finally,
push the grease filter back a little
more.
Depending on the cleaning agent
used, cleaning the grease filter in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filter in any way.
^ After cleaning, leave the filter to dry
for a while on an absorbent surface
before putting it back in place.
17
Cleaning and care
Fitting and replacing the
charcoal filter
If the cooker hood is connected for
recirculation, a charcoal filter (optional
accessory) must be inserted in addition
to the grease filter.
This is designed to absorb cooking
smells.
It is fitted in the canopy above the
grease filter.
Replacement charcoal filters can be
obtained from your Dealer /
Chartered Agent or the Miele Spare
Parts department or via the internet
on www.miele-shop.com. See back
cover for contact details, and
"Technical data" for type and
reference number.
Follow the instructions supplied with the
charcoal filter when fitting it.
Replace the charcoal filter at least
every six months or more frequently if
necessary.
Used charcoal filters can be disposed
of with the normal domestic waste.
18
Cleaning and care
Changing a halogen lamp
^ Pull out the deflector plate, and
remove the grease filter as described
earlier.
^ Switch off the fan and the lighting.
Exercise caution when changing
halogen lamps. They get very hot
during use, and remain hot for some
time after being switched off. Do not
touch the surface directly when
changing a lamp, as grease
particles from your fingers will
adhere to the surface and damage
it. Please follow the manufacturer’s
instructions.
^ Remove the charcoal filter if the
cooker hood is being used in
recirculation mode.
Before any cleaning or maintenance
work, disconnect the cooker hood
from the mains supply. Ensure that
– it is switched off at the wall socket
and the plug is withdrawn, or
– the fuse is withdrawn from the
fused spur connection unit, or
– the mains fuse is withdrawn,or
– the screw-out fuse is removed
(in countries where this is
applicable).
^ Push down the lighting unit slightly
via the opening in the safety panel.
^ The halogen lamp is now accessible
to be unscrewed anti-clockwise.
^ Replace it with a new halogen lamp
(specification: GU/GZ 10, 230 V,
50 W). Screw the lamp into the
socket and push it upwards.
Please follow the manufacturer's
instructions.
^ Replace the grease filter and, if being
used in recirculation mode, the
charcoal filter.
19
Appliance dimensions
DA 3160
DA 3190*
1) The front section of the wall housing
unit must be fitted with a shelf to the
depth of the partition wall.
2) The partition wall in the wall unit must
be removable.
3) In extraction mode: when measuring
for the height of the wall housing unit
and the cut-out, account must be taken
of any accessories fitted, e.g. silencer,
DSM module.
4) Recirculation mode with conversion
kit DUU 151.
5) Accessory DSM 400.
* Installation is also possible in a
600 mm wide unit.
DA 3180*
20
Appliance dimensions
Safety distance between hob and
cooker hood
The minimum safety distances
between the top of a cooker or hob
and the bottom of the cooker hood
are as follows, unless a greater
distance is specified by the
manufacturer of your cooking
appliance:
– 450 mm above electric hobs
and cookers,
– 650 mm above an open grill or
deep fat fryer,
– 650 mm above gas hobs and
cookers.
If this cooker hood is installed above
a Miele Wok CS 1028 CombiSet
appliance, a minimum safety
distance of 760 mm must be
maintained between the burner and
the lower edge of the cooker hood.
See “Warning and Safety
instructions” for further information.
21
Installation
Installation accessories
22
Installation
a 1 exhaust connection for exhaust
ducting C 150 mm.
b 1 reducing collar
for exhaust ducting C 125 mm.
c 1 non-return valve
for fitting into the exhaust
connection (not for recirculation
mode).
14 screws 3.5 x 16 mm
for securing the cooker hood into the
wall unit.
d 2 brackets
to support the appliance in the wall
unit.
8 screws M4 x 12 mm
for securing the cooker hood to the
brackets.
e 1 spacer strip
to conceal the gap between the rear
of the appliance and the wall.
4 of the screws can be used instead of
the plastic rivets to secure the spacer
strip.
f Conversion kit for recirculation
mode
including exhaust grille and flexible
aluminium hose with clips (this is not
included, but is available as an
optional extra - see Technical Data).
4 plastic rivets
for securing the spacer strip to the
back of the appliance.
g DML 300 installation kit (optional
accessory)
contains hinging and screws for
fixing a lightshield to match kitchen
furniture (lightshield not supplied with
cooker hood)
23
Installation
24
Installation
Positioning the appliance in
the wall housing unit
To position the appliance correctly,
cut the spacer strip to required depth
T, and then attach it to the back of
the appliance.
T= Depth of carcase K minus depth of
appliance G
^ The depth of appliance G depends
on the lightshield being used:
^ Screw the spacer strip to the bottom
of the sides of the housing, flush with
the rear wall.
– a Lightshield to match existing
kitchen furniture
– b DFB lightshield (optional
accesssory)
– c No lightshield.
This is based on a lightshield which
aligns with the front edge of the
carcase.
If the lightshield is further forward or
back, measurement T will need to be
adjusted accordingly.
^ Draw a vertical line up both inside
walls of the housing from the front of
the spacer strip.
When installing an interim shelf or
partition wall, the building-in space at
the back must not be less than
180 mm.
If it is less than 180 mm, position the
appliance further back, and reduce
measurement T accordingly. The
building-in position can be rectified
later by adjusting the depth.
^ Cut the spacer strip supplied to
measurement T.
Score along the groove for the
smaller measurement as shown, and
remove the surplus.
25
Installation
^ Place the appliance on its back.
Do not remove the protective film
between the deflector plate and the
casing until the hood has been
placed in the housing unit.
^ Screw the brackets onto the right and
left inside walls of the housing unit as
shown. The back edge of the
brackets should align with the vertical
line drawn up from the front of the
spacer strip, and the lower edge
aligned with the lower edge of the
housing unit side wall.
The brackets are designed for 16
and 19 mm thick carcase sides.
Orientate the bracket so that the
vertical depth matches the thickness
of the panel, as shown.
^ Hold the grease filter firmly, and pull
it out with the deflector plate as
shown.
^ Remove the grease filter and place to
one side.
^ Push the deflector plate back in.
26
Installation
^ When fitting a DA 3180 or a DA 3190
appliance into a 60 cm unit, unscrew
the brackets on the deflector plate
whilst it is pulled out.
Note for dismantling the cooker hood:
Undoing the screws on the left and
right inside the housing releases the
brackets, allowing the appliance to
be removed from the unit.
^ Push the cooker hood back against
the spacer strip.
^ Pull out the deflector plate.
^ Secure the appliance to the brackets
using two screws on each side.
^ Remove the protective film between
the deflector plate and the casing.
^ Lift the appliance up into the housing
from below, and engage in the
brackets.
27
Installation
Attaching the lightshield
^ Secure the front of the appliance to
the floor of the housing unit from
below using 4 screws (6 screws for
90 cm wide cooker hood).
To avoid damaging the deflector plate
when it is pulled out, care should be
taken to screw the fixing screws in
straight, and to ensure that the
screwheads are countersunk.
^ Attach the lightshield (if using).
A DML 300 installation kit, available as
an optional accessory, is required for
this.
This installation kit is supplied with the
DFB lightshield.
Follow the installation instructions
supplied.
Weight of a lightshield matching
existing furniture
The lightshield must not exceed 1300 g
in weight.
This applies to lightshields with a depth
of up to 30 mm.
For larger or heavier lightshields, the
weight must be reduced by e.g.
machining it away at the back.
^ Secure the spacer strip to the back of
the appliance from behind using
4 plastic rivets as shown.
28
Installation
Aligning the deflector plate
Fitting the grease filter
^ Remove the protective strip around
the edge of the grease filter.
Fit the grease filter.
^ The position of the deflector plate
can be brought forward by up to 50
mm using the adjusting screws on
either side of the deflector plate.
Align the deflector plate to the front of
the kitchen furniture units on either
side.
^ To do this, pull the deflector plate
out.
^ Turn the grease filter so that the red
plastic guides are at the front and
facing upwards.
^ Fit the grease filter in the front of the
deflector plate, press it upwards and
push it in together with the deflector
plate. It will slide onto the fixing pins
at the back. Finally, push the grease
filter back a little more.
29
Installation
Setting up for extraction mode
^ If the on-site ventilation system does
not have a non-return flap, then the
non-return flap supplied with the
appliance must be fitted in the
exhaust socket in the motor unit.
dai2699
^ When using C 150 mm ducting,
secure the exhaust connection
supplied to exhaust ducting with
hose clips.
^ If using C 125 mm ducting, fit the
reducing collar into the exhaust
connection, and secure the exhaust
ducting to the reducing collar with a
hose clip. (See "Connection for air
extraction").
dai2700
^ Place the exhaust ducting on the fan
connection for the cooker hood.
^ See "Connection for air extraction" for
further instructions on fitting the
ducting.
30
Installation
Setting up for recirculation
mode
If site conditions are not suitable for the
cooker hood to be used with air
extraction, the appliance must be set
up for recirculation.
^ Make sure that the slats in the
exhaust grille point towards the
centre of the room and not towards a
wall or the ceiling.
A non-return flap is not used in
recirculation mode.
14
3
^ Fit the charcoal filter (see “Cleaning
and care”).
9
31
10
Electrical connection
90
11
0
0
24
Refer to the notes in “Electrical
connection” and “Warning and
Safety instructions” before
connecting to the electricity supply.
3
22
40
33 160
^ For appliances connected to an
external motor (EXT models):
Connect the cooker hood to the
external motor using the connecting
cable and the 6-pole plug connector.
0
15
^ Separate fitting instructions are
supplied with the external motor.
For this, conversion kit DUU 151
(available from your Miele dealer or the
Miele Spare Parts Dept.) is required.
You will also need a charcoal filter (see
“Technical data”).
^ Fit the conversion kit as described in
the installation instructions supplied
with the kit.
31
Connection for air extraction
Important: To avoid the danger of
toxic fumes, please observe the
Warning and Safety instructions.
This is especially crucial when using
the cooker hood at the same time as
another heating appliance which
relies on air from the same room.
The cooker hood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
– Only use smooth pipes or flexible
hoses made from non-flammable
materials for the extraction ducting.
– When using an external motor, make
sure that the exhaust ducting is
sufficiently rigid. The external motor
can cause an underpressure which
can result in the exhaust ducting
distorting.
To achieve the greatest possible air
extraction with the lowest noise level,
please note the following:
– To ensure efficient air extraction, the
diameter of the exhaust ducting
should not be less than 150 mm.
– If flat ducting is being used, the
cross-sectional area must not be
smaller than the cross-sectional area
of the exhaust connection.
– All ducting, pipework and fittings
must be of non-flammable materials.
– The exhaust ducting should be as
short and straight as possible.
– Only use wide radius bends.
– The exhaust ducting should not be
kinked or compressed.
– Ensure that all connections are
strong and airtight.
– Where ducting is horizontal, it must
be laid to slope away at at least 1 cm
per metre. This is to ensure that
condensate cannot drain back into
the cooker hood.
32
Connection for air extraction
– If the exhaust air is to be ducted into
the open air, the installation of a
telescopic wall vent or roof vent
(available as an optional accessory)
is recommended.
Condensate trap
(optional accessory)
– If the exhaust air is to be ducted into
a vent flue, the ducting must be
directed in the flow direction of the
flue.
Important:
If the exhaust ducting is to run through
rooms, ceiling space etc. where there
may be great variations in temperature
between the different areas, the
problem of condensation will need to
be addressed. The exhaust ducting will
need to be suitably insulated.
In addition to insulating the exhaust
ducting, we recommend that a suitable
condensate trap is also installed to
collect and evaporate any condensate
which may occur. Condensate traps
are available for C 125 mm or
C 150 mm ducting.
When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the
exhaust connection. The arrow on the
housing indicates the direction of
air-flow.
Cooker hoods designed for use with an
external motor (...EXT models) have an
integrated condensate trap.
33
Connection for air extraction
Silencer
...with air extraction:
(optional accessory)
The silencer not only reduces noise
from the fan, but also sounds from
outside (e.g. traffic noise).
For this reason the silencer must be
positioned as close as possible to where
the ducting leaves the building a.
...in recirculation mode:
The silencer needs to be positioned
between the fan and the exhaust grille
b. Ensure there is adequate space for
fitting it.
To achieve even further reductions in
noise levels, a special silencer can be
fitted in the ducting system.
...air extraction with external motor:
To minimise noise from the motor in the
kitchen, the silencer should be
positioned in front of the external motor
c if possible, or if the ducting is long,
then in the ducting above the cooker
hood itself d.
In the case of an external motor placed
inside the house, fitting a silencer
behind the external motor e reduces
the noise of the fan outside the house.
In all modes of operation, the most
effective noise reductions are
achieved if two silencers are fitted in
the system.
34
Electrical connection
All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national
and local safety regulations
(BS 7671 in the UK).
Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
manufacturer cannot be held liable.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
The connection data is given on the
data plate. This is visible when the
grease filters have been removed.
Ensure that this data matches the
household mains supply.
If the switch is not accessible after
installation (depending on country), an
additional means of disconnection must
be provided for all poles.
For extra safety it is advisable to protect
the appliance with a suitable residual
current device (RCD). Contact a
qualified electrician for advice.
Important
This appliance is supplied for
connection to an a.c. 230 V single
phase 50 Hz supply.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue
= neutral
Brown
= live
WARNING:
THIS APPLIANCE MUST BE
EARTHED
Connection of this appliance should be
made via a suitable isolator or a double
pole fused spur connection unit which
complies with national and local safety
regulations and the On-Off switch
should be easily accessible after the
appliance has been built in.
When switched off there must be an
all-pole contact gap of 3 mm in the
switch (including switch, fuses and
relays according to EN 60335).
35
Operation with DSM 400 control module
The Miele DSM 400 control module can
be used to combine the cooker hood
with other components.
It enables the following:
Connection to a window contact
switch
If adequate ventilation to the room can
only be ensured by having a window
open when the cooker hood is in use at
the same time as a heating appliance
which depends on the air from the
same room, then the control module
can be used to connect a window
contact switch (not supplied) to the
appliance.
Once connnected, the cooker hood can
only be operated when the window is
sufficiently open (see also "Warning
and Safety instructions").
When the window is closed, the cooker
hood fan cannot be switched on. The
indicator lamp for the On/Off touch
control on the cooker hood will flash.
The cooker hood lighting is not affected
by this.
EXT models can also be connected to a
window contact switch.
Take care when ventilating the room
through an open window that ventilation
is not impaired by a closed blind or
curtain.
The window contact switch must be
tested for safety after it has been
connected.
36
If the control module is
disconnected in order to operate the
cooker hood without the window
contact switch (e.g. after moving
house), the cooker hood electronics
must be reset by a Miele service
technician.
Potential free connection
This enables a further appliance to be
controlled by the switch setting on the
cooker hood fan.
– For instance it can be used to ensure
a sufficient supply of fresh air when
the cooker hood and a heating
appliance which also depends on
the air in the room are being used
together, by switching on an air
intake fan, or opening a motorised
inlet flap as soon as the cooker hood
fan is switched on.
It is important to ensure that the fan
power is sufficient and that the air
intake has a suitable cross-sectional
diameter.
– If a sufficient air intake cannot be
guaranteed, then the potential free
contact will enable a heating
appliance, which depends on air in
the same room as a cooker hood, to
be switched off when the cooker
hood is in operation.
See also "Warning and Safety"
instructions.
All appliances must be tested for safety
after they have been connected.
Operation with DSM 400 control module
Connection to a light switch
The control module can be used to
switch on the cooker hood lighting via a
light switch in the house.
Installation
The control module must be installed
above the cooker hood housing.
The control module is supplied with its
own detailed operating and installation
instructions.
37
After Sales Service
In the event of a fault which you cannot
correct yourself, or if the appliance is
under guarantee, please contact:
– Your Miele Dealer / Chartered Agent
or
– The Miele Service Department (see
back cover for address).
When contacting your Dealer or Miele,
please quote the model and serial
number of your appliance. These are
shown on the data plate which is visible
when the grease filter is removed.
For G.B.: Please note that telephone
calls may be monitored and
recorded for training purposes.
N.B. A call-out charge will be applied
for service visits where the problem
could have been resolved as described
in these instructions.
38
Technical data
Connected load* . . . . . . . . . . . . . 280 W
Fan motor* . . . . . . . . . . . . . . . . . 180 W
Hob lighting . . . . . . . . . . . . . . 2 x 50 W
* For EXT models the connected load
and extraction power will depend on
the type of external motor fitted.
Voltage . . . . . . . . . . . . . . . . . AC 230 V
EXT models:
Length of connection cable to external
motor. . . . . . . . . . . . . . . . . . . . . . . 1.9 m
Frequency . . . . . . . . . . . . . . . . . . 50 Hz
Fuse rating (UK) . . . . . . . . . . . . . . . . 5 A
Electrical cable length . . . . . . . . . 1.5 m
Weight
DA 3160 . . . . . . . . . . . . . . . . . . . . 12 kg
DA 3160 EXT . . . . . . . . . . . . . . . . 10 kg
DA 3190 . . . . . . . . . . . . . . . . . . . . 14 kg
DA 3190 EXT . . . . . . . . . . . . . . . . 12 kg
Fan performance*
Extraction power according to EN 61591
Extraction system ø 150 mm:
Level I . . . . . . . . . . . . . . . . . . . 150 m3/h
Level II. . . . . . . . . . . . . . . . . . . 275 m3/h
Level III . . . . . . . . . . . . . . . . . . 400 m3/h
Intensive Setting . . . . . . . . . . . 550 m3/h
Recirculation with charcoal filter:
Level I . . . . . . . . . . . . . . . . . . . . 80 m3/h
Level II. . . . . . . . . . . . . . . . . . . 180 m3/h
Level III . . . . . . . . . . . . . . . . . . 280 m3/h
Intensive Setting . . . . . . . . . . . 350 m3/h
Optional accessories for
recirculation mode:
- Conversion Kit DUU 151
- Miele charcoal filter DKF 13-1
39
Alteration rights reserved / 0310
M.-Nr. 07 777 490 / 00