GAS HOB ZGL 62 INSTRUCTION BOOKLET Please read this instruction booklet before using the appliance GB Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation z z z z This appliance must be installed and serviced by a competent person as stated in the Gas Safety ( Installation and Use) Regulations Current Editions and the IEE Wiring Regulations. Remove all packaging before using the hob. Ensure that the gas and electrical supply complies with the type stated on the rating plate, located near the gas supply pipe. Do not attempt to modify the hob in any way. Child Safety z z z z This hob is designed to be operated by adults. Do not allow children to play near or with the hob. The hob gets hot when it is in use. Children should be kept away until it has cooled. Children can also injure themselves by pulling pans or pots off the hob. During Use z z z z z z z z z z 2 This hob is intended for domestic cooking only. It is not designed for commercial or industrial purposes. This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation. When in use a gas cooking appliance will produce heat and moisture in the room in which it has been installed. Ensure there is a continuous air supply, keeping air vents in good condition or installing a cooker hood with a venting hose. When using the hob for a long period of time, the ventilation should be improved, by opening a window or increasing the extractor speed. Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. Ensure the control knobs are in the ‘OFF’ position when not in use. When using other electrical appliances, ensure the cable does not come into contact with the hot surfaces of the cooking appliance. Unstable or misshapen pans should not be used on the hob as unstable pans can cause an accident by tipping or spillage. Never leave the hob unattended when cooking with oil and fats. Never use plastic or aluminium foil dishes on the hob. z Perishable food, plastic items and aerosols may be affected by heat and should not be stored above or below the hob unit. Service z This hob should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. Environmental Information z z z After installation, please dispose of the packaging with due regard to safety and the environment. When disposing of an old appliance, make it unusable, by cutting off the cable. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. Keep this instruction book for future reference and ensure it is passed on to any new owner. Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions ) Step by step instructions for an operation Hints and Tips Environmental Information Contents For the Installer For the User Important Safety Information 2 Instructions for the Installer 8 Description of the Hob 3 Installation 10 Operation 4 Electrical connections 12 Maintenance and Cleaning 5 Wiring Diagram 13 Something Not Working? 6 Fault Finding 13 Service and Spare Parts 6 Commissioning 15 Customer Care 7 Conversion from Natural Gas to LPG 15 Guarantee Conditions 7 This appliance complies with the following E.E.C. Directives: * 73/23 - 90/683 (Low VoltageDirective); * 93/68 (General Directives); * 89/336 (Electromagnetical Compatibility Directive); * 90/396 (Gas Appliances), and subsequent modifications Description of the Hob 3 2 3 1 4 1. 2. 3. 4. 5. 5 Hob Top Rapid Burner Semi-rapid Burners Auxiliary Burner Control knobs 3 Operation Hob burners ) To light a burner: turn the relevant control knob anticlockwise to the maximum position, then push it down to ignite the burner; z then, check the flame is regular and adjust it as required. If you cannot light the flame even after several attempts, check the "cap" and “crown” (see diagram - letter A and B) are in the correct position. To put the flame out, turn the knob to the symbol z. z When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically. To ensure maximum burner efficiency, you should only use pots and pans with a flat bottom fitting the size of the burner used (see table). Burner Large (rapid) Medium (semi-rapid) Small (auxiliary) minimum diameter 180 mm 120 mm 80 mm maximum diameter 260 mm 220 mm 160 mm If you use a saucepan which is smaller than the recommended size, the flame will spread beyond the bottom of the vessel, causing the handle to overheat. Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite. As soon as a liquid starts boiling, turn down the flame so that it will barely keep the liquid simmering. If the control knobs become difficult to turn, please contact your local Service Force Centre. 4 A - Burner cap B - Burner crown C - Ignition electrode Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added. Avoid the use of the following: - household detergent and bleaches; - impregnated pads unsuitable for non-stick saucepans; - steel wool pads; - bath/sink stain removers. Should the hob top become heavily soiled, the following products are recommended: - For stainless steel hobs use a proprietary stainless steel cleaner. - For other hobs use Hob Brite or Bar Keepers Friend. Pan Supports The pan supports are dishwasher proof. If washing them by hand, take care when drying them as the enamelling process occasionally leaves rough edges. If necessay, remove stubborn stains using a paste cleaner. The Burners The burner caps and crowns can be removed for cleaning. Wash the burner caps and crowns using hot soapy water, and remove marks with a mild paste cleaner. A well moistened soap impregnated steel wool pad can be used with caution, if the marks are particularly difficult to remove. After cleaning, be sure to wipe dry with a soft cloth. Ignition electrode The electric ignition is obtained through a ceramic "electrode" and a metal electrode (see diagram on page 4 - letter C). Keep these components very clean, to avoid lighting difficulties, and check that the burner crown holes are not obstructed. 5 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Zanussi Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMPTOM There is no spark when lighting the gas SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e.g. after cleaning. The gas ring burns unevenly Check the main jet is not blocked and the burner crown is clear of food particles. Check the burner cap and crown have been replaced correctly, e.g. after cleaning. Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Zanussi Service Force Centre by telephoning: 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk Before calling out an engineer, please ensure you have read the details under the heading “Something Not Working.” 6 When you contact the Service Force Centre you will need to give the following details: 1. Your name, address and post code 2. Your telephone number 3. Clear and concise details of the fault 4. The model and serial number of the appliance (found on the rating plate) 5. The purchase date Please note that a valid purchase receipt or guarantee documentation is required for inguarantee service calls. Customer Care Department For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.zanussi.co.uk Customer Care Department ZANUSSI 55-77 High Street Slough Berkshire SL1 1DZ 08705 727727 (*) * calls to this number may be recorded for training purposes. Guarantee Conditions Zanussi Guarantee conditions We, Zanussi, undertake that if, within 24 months of the date of the purchase, this Zanussi appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: * The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate. * The appliance has been used for normal domestic purpose only, and in accordance with the manufacturer's instructions. * The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. * All service work under this guarantee must be undertaken by a Zanussi Service Centre. * Any appliance or defective part replaced shall become the Company's property. * This guarantee is in addition to your statutory and other legal rights. Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours, in which case a premium will be charged. Exclusions This guarantee does not cover: * Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable parts of glass or plastic. * Costs incurred for calls to put right an appliance which is improperly installed or calls to appliance outside the United Kingdom. * * Appliances found to be in use within a commercial or similar environment, plus those which are the subject to rental agreements. Products of Zanussi manufacture which are not marketed by Zanussi. European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications: * The guarantee starts from the date you first purchased your product. * The guarantee is for the same period and to the same extent for labour and parts as exist in the new country of use for this brand or range of products. * This guarantee relates to you and cannot be transferred to another user. * Your new home is within the European Community (EC) or European Free Trade Area. * The product is installed and used in accordance with our instructions and is only used domestically, i.e. a normal household * The product is installed taking into account regulations in your new country. Before you move, please contact your nearest Customer Care centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden UK Senlis Nürnberg Pordenone Stockholm Slough +33 (0) 3 44 62 29 29 +49 (0) 800 234 7378 +39 (0) 0434 39 4700 +46 (0) 8 672 53 90 +44 (0) 1753 219897 7 Instructions for the Installer Engineers technical data Overall dimensions Width: Depth: Rear Left Burner Heat Input 580 mm 500 mm Front Left Burner (rapid) Heat Input 3.0 kW Natural gas (10236 BTU/HR) 2.8 kW L.P.G. (9554 BTU/HR) Cut out dimensions Width: Depth: (semi rapid) 2.0 kW (6824 BTU/HR) 550 mm 470 mm Supply connections Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Rear Right Burner Heat Input (semi rapid) 2.0 kW (6824 BTU/HR) Front Right Burner Heat Input (auxiliary) 1.0 kW (3412 BTU/HR) Burner VALUE = 37.78 MJ/m3 Characteristics Ws - 50.7 MJ/ m3 VALUE = 49.92 MJ/Kg LPG GAS 28-30/37 mbar NATURAL GAS 20 mbar TYPE OF GAS Electric: 230 V 50 Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. BURNER POSITION SEMI-RAPID (medium) AUXILIARY (small) MAX MIN MAX MIN MAX MIN 3.0 0.65 2.0 0.45 1.0 0.33 0.286 0.062 0.190 0.043 0.095 0.031 119 Adjust. 96 Adjust. 70 Adjust. NOMINAL THERMAL POWER kW 2.8 0.65 2.0 0.45 1.0 0.33 NOMINAL FLOW RATE g/h 202 47 144 32 72 24 NOZZLE REFERENCE 1/100 mm 86 40 71 32 50 28 NOMINAL THERMAL POWER kW NOMINAL FLOW RATE m3/h NOZZLE REFERENCE 1/100 mm Dia. Tap By-pass 1/100 mm Auxiliary Semi-rapid 28 32 Rapid 40 Aeration adjustment none 8 RAPID (large) APPLIANCE CLASS: APPLIANCE CATEGORY: 3 II2H3+ APPLIANCE GAS SUPPLY:Natural gas G20/20 mbar Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Provision for ventilation Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Part 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m3. If it is installed in a room of volume less than 5 m3 an air vent of effective area of 110 cm2 is required. If it is installed in a room of volume between 5 m3 and 10 m3 an air vent of effective area of 50 cm2 is required, while if the volume exceeds 11 m3 no air vent is required. However, if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m3 and 11 m3. If there are other fuel burning appliances in the same room, B.S. 5440 Part 2 Current Edition, should be consulted to determine the requisite air vent requirements. Location The hob may be located in a kitchen, a kitchen/diner or bed sitting room, but not in a bathroom, shower room or garage. Before making the cut out in the worktop ensure that there is a minimum distance of 55 mm between the rear edge of the hob and the wall. A minimum distance of 100 mm must be left between the side edges of the hob and any adjacent cabinets or walls. The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 400 mm. If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob. The minimum distance combustible material can be fitted directly above the hob is 700 mm. ICLEARANCES REQUIRED CLEARANCES REQUIRED WHEN FITTING THE HOB WITH A COOKER HOOD ABOVE WHEN FITTING THE HOB WITHOUT A COOKER HOOD ABOVE 600 mm 700 mm 650 mm 700 mm 400 mm 50 m 55 400 mm mm m 100 400 mm mm mm m 100 50 m 55 50 m 400 mm mm m 50 m m FO 0812 FO 0813 9 Installation IMPORTANT: This hob must be installed by a competent person to the relevant Gas Standards. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. WHEN THE HOB IS FIRST INSTALLED Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory. Any gas installation must be carried out by a competent person. The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. On the end of the shaft, which includes the GJ 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. FO 0814 Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob. It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. FO 0264 A) End of shaft with nut B) Washer C) Elbow Cut Out Size 30 470 The dimensions of the cut-out are given in the diagram. 550 FO 2098 Dimensions are given in mm. 10 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. 2 3 ON/OFF SWITCH 30 ON/OFF SWITCH a 60 FLEX OUTLET 20 min 1 It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2. b FLEX OUTLET FO 0763 FO 1013 FO 0764 Dimensions are given in mm. Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. Fitting the Hob into the worktop )Carry out the building in of the hob as follows: • • • put the seals supplied with the hob, on the edges of the cut out taking care that the seals meet without overlapping; place the hob in the cut out, taking care that it is centred; fix the hob with the relevant fixing clamps and screws, as shown in the diagram. When the screws have been tightened, the excess seal can be removed. a Seal The edge of the hob forms a double seal which prevents the ingress of liquids. FO 0199 11 Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230 V 50 Hz AC electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate. The rating plate is located on the bottom of the hob. A copy is attached on the back cover of this book. Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cable does not come into contact with surfaces with temperatures higher than 50 deg. C. The hob is supplied with a 3 core flexible supply cable incorporating a 3amp plug fitted. In the event of having to change the fuse, a 3amp ASTA approved (BS 1362) fuse must be used. Should the plug need to be replaced for any reason, the wires in the mains lead are coloured in accordance with the following code: Green and Yellow - Earth Blue - Neutral Brown - Live ) — Connect the green and yellow (earth) wire to the terminal in the plug which is marked with the letter 'E' or the earth symbol or coloured green and yellow. — Connect the blue (neutral) wire to the terminal in the plug which is marked with the letter 'N' or coloured black. — Connect the brown (live) wire to the terminal in the plug which is marked with the letter 'L' or coloured red. Upon completion there must be no cut, or stray strands of wire present and the cable clamp must be secure over the outer sheath. A cut off plug inserted into a 13 amp socket is a serious safety (shock) hazard. Ensure that the cut off plug is disposed of safely. 12 FO 0390 Wiring Diagram A. TAPS IGNITOR SWITCHES B. IGNITOR UNIT Fault Finding Preliminary Electrical Systems Check Blue START Isolate appliance and carry out: A: Earth Continuity check. Blue Brown Neutral Wire Blue E( ) FUSE Brown SOCKET (face view) PLUG (with cover removed) Earth Wire ( ) Green/Yellow N L Green Yellow YES NO Carry out: C: Polarity check. Has inlet fuse blown? YES NO Inlet wiring faulty. Rectify any fault. Isolate appliance and carry out: B: Insulation check. Rectify any fault including replacing fuses as necessary. Carry out: D: Resistance to Earth check. Electricity supply should now be satisfactory. A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale and adjust zero if necessary. a) Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 Ω (Ohm), check all earth wires for continuity and all contacts are clean and tight. B. INSULATION CHECK - Appliance electrically disconnected, all switches ON. a) meter set on Ω (Ohms) x 1 scale. Test leads from L to N in appliance terminal block. If meter reads «0» then there is a short circuit. b) meter set on Ω (Ohm) x 100 scale. Repeat test with leads from L to E. If meter reads less than ∞ (infinity) there is a fault. NOTE - Should it be found that the fuse has failed but no fault is indicated - a detailed continuity check (i.e. by disconnecting and checking each component) is required to trace the faulty component. It is possible that a fault could occur as a result of local burning/arcing but no fault could be found under test. However a detailed visual inspection should reveal evidence of burning around the fault. 13 Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check by pass simmer Check polarity and earth continuity of supply point Check position of the electrode Check earth continuity of appliance Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from 'L' on the mains connector block and the taps ignition switches Check continuity from ignition switches connector to ignitor unit Check continuity from the tip of each electrode to the terminals 1 to 4 on the ignitor unit Check for breaks in the insulation of the HT leads Change the taps ignition switches Change the ignitor unit 14 Check fitting of burners Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. - Turn the gas tap to the MAX position and ignite. - Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. ) - - Re-ignite the burner and set to MIN. Remove the control knob and use a thin bladed screwdriver to turn the adjustment screw until the flame is steady and does not extinguish, when the knob is turned from MIN to MAX. The adjustment screw may be located at the centre of the gas tap control shaft or on the gas tap body, left of the control shaft or below (see diagram). Repeat the adjustment procedure for all burners. ) - Procedure: Pressure Testing Remove left hand pan support and front left burner cap and crown. Fit manometer tube over the injector. Turn on the burner gas supply and ignite another burner. The pressure reading should be nominally 20mbar and must be between 17 mbar and 25mbar. Turn off the burner supplies. Adjustment screw Conversion from Natural Gas to LPG IMPORTANT The replacement/conversion of the gas hob should only be undertaken by a competent person. It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to suit. To adjust the gas rate With the aid of a thin bladed screwdriver completely tighten down the by pass adjustment screw, which is located down the centre of the gas tap control shaft. Upon completion stick the replacement rating plate on the under side of the hob. Method • Ensure that the gas taps are in the 'OFF' position • Isolate the hob from the electrical supply • Remove all pan supports, burner caps, rings, crowns and control knobs. • With the aid of a 7mm box spanner the burner injectors can then be unscrewed and replaced by the appropriate LPG injectors. 15 CUSTOMER CARE ZANUSSI 55-77 High Street Slough Berkshire, SL1 1DZ Tel: 08705 727727 Long Mile Road Dublin 12 Republic of Ireland Tel: + 353 (0) 1 4090751 © Electrolux plc 2003 From the Electrolux Group. The world’s No.1 choice. 35675-2602 01/05 Grafiche MDM - Forlì The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.