Samsung SVD-4600 SVD-4600 User guide

High Resolution Vandal-proof Dome Camera SVD-4600 User Guide
Before installing and operating this product,
please read this manual thoroughly.
ENGLISH
Before operating the camera, confirm the camera model and proper input power
voltage. In order to that you can understand this manual thoroughly, we'll introduce our
model description.
nSVD-4600 SERIES
• NTSC MODEL SVD-4600(W)N
• PAL MODEL
SVD-4600(W)P
n MODEL DESCRIPTION
• SVD-4600(W)X
__
SIGNAL SYSTEM
CAMERA COLOR • SIGNAL SYSTEM
N → NTSC MODEL
P → PAL MODEL
• CAMERA COLOR
→ SILVER COLOR
W → IVORY COLOR
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.
INFORMATION -This equipment has been tested and found to comply with limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
WARNING - To prevent electric shock and risk of fire hazards:
◆ Do NOT use power sources other than that specified.
◆ Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Features
Contents
• Precautions… …………………………………………………………………… 7
• Components and Accessories……………………………………………… 9
• Overview…………………………………………………………………………… 9
Ultra High Resolution
Day & Night
By adopting a double-speed 410,000 pixel Sony CCD, the
camera produces clear picture quality with a horizontal
resolution of 560 TV lines for color, and 700 TV lines for B/W.
The camera identifies whether it is day or night and
automatically switches to the appropriate mode, depending on
its environment. By day, the camera switches to color mode in
order to maintain optimal color. At night, it switches to B/W
mode so as to obtain better picture definition.
• Connection………………………………………………………………………… 10
■ Connecting To Monitor… ……………………………………………………………… 10
■ Connecting To Power…………………………………………………………………… 11
■ RS-485 communication control……………………………………………………… 12
Vari-focal Lens Built-in
DIS (Digital Image Stabilizer)
With built-in vari-focal lens, the camera can control the focal
distance easily from 2.8 to 10.0mm.
The DIS function compensates for any camera
movement, to produce more stable pictures.
• Operating Your Camera……………………………………………………… 13
■ Menu Configuration……………………………………………………………………… 13…
■ Menu Setup… …………………………………………………………………………… 13…
• LENS……………………………………………………………………………………………14…
• EXPOSURE… …………………………………………………………………………………15…
• WHITE BALANCE……………………………………………………………………………16…
• BACKLIGHT……………………………………………………………………………………18…
• SSNR………………………………………………………………………………………… 20…
• DAY/NIGHT… …………………………………………………………………………………21…
• IMAGE ADJ… ……………………………………………………………………………… 22…
• SPECIAL……………………………………………………………………………………… 24…
• EXIT…………………………………………………………………………………………… 28
• Troubleshooting………………………………………………………………
29
• Specification……………………………………………………………………
30
• Dimension… ……………………………………………………………………
30
Sub Monitor Function
Wide Dynamic Range (WDR):
The sub monitor function enables easy adjustment of the
camera angle within the monitoring range during its installation.
By adopting a proprietary SV-IV DSP chip, the camera delivers
clear, high quality pictures even in backlight, by increasing
exposure in dark areas while decreasing it in bright areas; a
corrected image with clear details results.
IP66 Approved /
Dust & Rain Resistant
With dust and rain resistant design, the camera can be
installed ouside under building eaves or place that is
esposed to the dust and rain.
Excellent Sensitivity
Miscellaneous Functions
Adopting a Diagonal 6mm (1/3"), highly sensitive CCD and
digital signal processing technology, it can clearly
distinguish the outline and color of a subject in an
extremely low luminance environment – even, for example,
under starlight. Since surveillance is possible in places
where the light is poor, the camera is appropriate for day
and night surveillance outdoors or on the outside of
buildings.
- 0.00004 Lux
SYNC(INT/LL), SENS-UP, FREEZE, FLIP(H/V-REV),
D-ZOOM, SHARPNESS, MOTION DETECTION and
PRIVACY functions are provided.
RS-485 Communication
Control Support
Remote OSD menu control via an RS-485 interface is supported.
COLOR CCD CAMERA
4
User Guide
SSNR (Samsung Super Noise
Reduction) Function
OSD
The high performance SV-IV DSP chip
dramatically reduces the gain noise in digital
image processing, producing clear, sharp images
in low lighting environments.
The camera control is convenient by using 9 different
foreign language O.S.D.
- NTSC : Korean, English, Spanish, Japanese, French, Portuguese
- PAL : English, French, German, Spanish, Italian, Chinese, Portuguese
COLOR CCD CAMERA
5
User Guide
Samsung Techwin cares for the environment at all product manufacturing
stages to preserve the environment, and is taking a number of steps to provide
customers with more environment-friendly products.The Eco mark represents
Samsung Techwin’s will to create environment-friendly products, and indicates
that the product satisfies the EU RoHS Directive.
Precautions
Do not install the camera in
extreme temperature conditions.
Do not install or use the camera in an
environment where the humidity is high.
Warnings & Cautions
This information is provided to ensure your safety and to prevent any losses, financial or
otherwise. Please read it carefully and use the product accordingly.
* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as
an aerial ladder while providing after-sales service shall be at your expense.
* Separate the power plug when thunder crashes or lighting flashes.
* This product is support equipment for surveillance system. Therefore, we can't compensate for material loss and/or
personal injuries by robbery, fire, natural disaster or something like this type.
Warning/Attention/Special Mark Messages
Ignoring this information may
result in material loss and/or
serious personal injuries including
death.
Ignoring this information may
result in material loss and/or a
slight injuries.
Indicates “Never Allowed.”
Indicates “No Disassembling.”
Only use the camera under conditions
where temperatures are between
-10ºC and +50ºC. Be especially careful
to provide ventilation when operating
under high temperatures.
Do not install the camera under
unstable lighting conditions.
Severe lighting change or flicker can
cause the camera to work improperly.
COLOR CCD CAMERA
6
User Guide
It can cause the image quality to be
poor.
COLOR CCD CAMERA
Do not touch the front lens of the
camera.
It is one of the most important parts of
the camera. Be careful not to be
stained by fingerprint.
7
User Guide
Precautions
Components and Accessories
Do not drop the camera or subject
them to physical shocks.
Never keep the camera face to
strong light directly.
❶
2
3
6
It can cause malfunctions to occur.
It can damage the CCD.
❶ SVD-4600 5 Wrench
2 Instruction Manual 6 Template
5
4
7
3 M5 Tapping Screw 4EA 4 Quick Install Guide 7 Installation Video Output Cable
Overview
Do not expose the camera to
radioactivity.
⓫
⓬
1
3
2
If it is exposed to radioactivity, For
heated CCD, it will be out of order.
5 4
Notes
• I f the camera is exposed to spotlight or object reflecting strong light, smear or
blooming may occur.
• P lease check that the power satisfies the normal specification before connecting
the camera.
8
7
6
❿
COLOR CCD CAMERA
8
User Guide
COLOR CCD CAMERA
9
9
User Guide
Overview
❶ Pan Base : control panning angle of camera
Intermediate End monitor
2 Rotate Base : control rotating angle of camera
3 X3.6 Vari-focal Lens Module
4 Rotate Base Holding Screw : fix rotated position
5 Pan Base Holding Screws (Color : Silver) : fix panned position
6 RS-485 Control Cable : The detailed description refers to p12
7 Power Input Jack
8 Video Output Jack
CCTV Camera
9 Function Setup switch : display the menu on the screen and move the cursor to four
directions to confirm status or after changing a selected item.
❿ Video Output Terminal to Monitor ⓫ Dome Cover ⓬ Shield Case
Connecting to Power
Connect the adaptor to the power input
power input terminal connector as shown in the figure below.
The recommended adaptor specification
for SVD-4600 is AC 24V / 500mA or DC 12V
/ 500mA.
Connection
Connecting to Monitor
Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.
When the resistance value of copper wire is at [20ºC(68°F)]
Copper wire size (AWG)
#24(0.22㎟)
#22(0.33㎟)
#20(0.52㎟)
#18(0.83㎟)
Resistance (Ω / m)
0.078
0.050
0.030
0.018
Voltage Drop (V/m)
0.078
0.018
0.011
0.006
• As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an
excessively long adaptor output line for connection to the camera may affect the
performance of the camera.
CCTV Camera
Monitor
• As the connecting method varies with the instruments, refer to the manual supplied with the
instrument.
• If necessary, you can connect the monitor to the REMOTE jack on the back of your camera.
• Only connect the cable when the power is turned off.
• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.
COLOR CCD CAMERA
10 User Guide
*Standard voltage for camera operation : DC 12V ± 10%, AC 24V±10%
*There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
Notes
• Be sure to connect power only after all the installation is complete.
• Use the UL listed, class 2 power transformer of AC 24V adaptor.
• Ground should be connected to the GND terminal.
COLOR CCD CAMERA
11 User Guide
Connection
Operating Your Camera
Menu Configuration
RS-485 communication control
Setup Menu
Connecting to RS-485 Control Cable
CONTROL CABLE
SPEC
RED (TRX+)
RS-485+
WHITE(TRX-)
RS-485-
Using a RS-485 communication, it will be able to control the OSD menu at the
SAMSUNG TECHWIN System Controller or DVR.
(1) The case which it controls from the PC
Using a RS-485 converter, It connects to RS-485 control cable outside camera
and serial cable
EX) SERIAL PORT OF THE PC(COM1) → SERIAL CABLE → RS-485 CONVERTER → RS-485
CONTROL CABLE
(2)The case which it controls from the DVR or System Controller
It connects the RS-485 control cable in the connection terminal of 485 control
boards which are connected with the DVR or System Controller.
485 Control Board Connection Port
(+) CONNECTION TERMINAL
(-) CONNECTION TERMINAL
RS-485 Control Port
RED (TRX+)
WHITE (TRX-)
* RS-485 Communication establishment initial value
Item
Initial value
Camera ID
1
BAUD RATE
9600
UART MODE
8-NONE-1
RET PKT
ENABLE
LENS
●DC
EXPOSURE
●SHUTTER
● RETURN
●AGC ● SENS-UP WHITE BALANCE
● ATW
●OUTDOOR
●MANUAL
● INDOOR
●AWC→SET
BACKLIGHT
● OFF
● HLC
●WDR
● BLC
SSNR
● ON
● OFF
DAY/NIGHT
● COLOR
●B/W
IMAGE ADJUSTMENT
(IMAGE ADJ.)
●FREEZE
●D-ZOOM
●V-REV ● H-REV
●SHARPNESS ● RETURN
SPECIAL
●CAMTITLE
●PRIVACY
●LANGUAGE
●SYNC ●DIS ●RESET
Menu Setup
Use the Function Setup switch on back of the camera.
Function Setup switch
Notes
12 User Guide
●MOTION DET
●COMM ADJ
●RETURN
EXIT
• When you construct external control systems for a camera control, please use to the SAMSUNG
TECHWIN PROTOCOL or PELCO-D PROTOCOL.
• When you connecting to RS-485 control cable, please peel off the outer skin inside the RS-485
control cable.
• In case of SCC-101 connection, change communication mode to 『8-E-1』 at 『Communication
configuration』menu. (For more information, refer to SCC-101 manual.)
COLOR CCD CAMERA
●AUTO
COLOR CCD CAMERA
13 User Guide
Operating Your Camera
1. Press the Function Setup switch.
• Main setup menu is displayed on the monitor screen.
Select the function by moving
up or down direction of
function setup switch.
MAIN SETUP
1.LENS
2.EXPOSURE 3.WHITE BAL
4.BACKLIGHT
5.SSNR
6.DAY/NIGHT
7.IMAGE ADJ
8.SPECIAL
9.EXIT
Change the status by
moving right or left
direction of function setup
switch.
DC
ATW
OFF
ON
AUTO
EXPOSURE
Notes
• An item with the icon also has sub menus. To select a sub menu, select an item
with the icon and press the Function Setup switch.
• An item with the - - - icon is unavailable due to function settings.
LENS
Using this function, you can control screen brightness.
1. When the SETUP menu screen is displayed, select 'LENS' by using the Function
Setup switch so that the arrow indicates 'LENS'.
COLOR CCD CAMERA
14 User Guide
MAIN SETUP
1.LENSDC
2.EXPOSURE 3.WHITE BALATW
2. Select a desired function using the Function Setup switch.
• Place the cursor over a desired item.
3. Set up a selected item by using the Function Setup switch.
4. To finish the setting, select ‘EXIT’ and press the Function Setup switch.
MAIN SETUP
1.LENSDC
2.EXPOSURE
DC : Select Auto Iris Lens
• When DC is selected, you can control screen
brightness. The range of brightness control is
between 1 and 70. Adjust the brightness
appropriately for optimal screen brightness.
1. When the SETUP menu screen is displayed, select
'EXPOSURE' by using the Function Setup switch so that
the arrow indicates 'EXPOSURE'.
2. Select a desired mode using the Function Setup switch.
SHUTTER : Because of using a DC lens, the shutter speed is fixed.
(NTSC mode l: 1/60 sec, PAL model : 1/50 sec)
When flickering occurs on the screen, select the A.FLK mode using the
Function Setup switch.
- A.FLK : Select this when you experience picture flicker, which can happen when there is a
clash with the frequency of the installed lighting.
Notes
• To produce better results with A.FLK, do not use it in conjunction with the WDR
mode of the BACKLIGHT menu.
• When the SHUTTER is set to A.FLK mode, SENS-UP will be disabled.
COLOR CCD CAMERA
15 User Guide
Operating Your Camera
A
GC (AUTO GAIN CONTROL) :
The higher the gain level, the brighter the screen - but the higher the noise.
- OFF : Deactivates the AGC function.
- LOW : Allows automatic gain control from 5.3dB to 30dB.
- HIGH : Allows automatic gain control from 5.3dB to 42dB.
SENS-UP :
When it is night or dark, the camera automatically detects the light level and maintains a clear picture if this mode is activated.
- OFF : Deactivates the SENS-UP function.
- AUTO : Activates the SENS-UP function.
RETURN :
Select this to save the changes in the EXPOSURE menu and return to the SETUP menu.
Notes
• If you press the Function Setup switch in ‘AUTO’ mode, You can adjust brightness by
increasing or decreasing the shutter speed. (x2 ~ x256)
• Note that the higher the zoom level, the brighter the screen, but the more likely it is
that an after-image will appear.
• Although Noise, Spots, and Whitish symptoms may occur in SENS-UP operation
when the zoom level is increased, this is normal.
White Balance (White Bal.)
Use the White Balance function to adjust the screen color.
1. When the SETUP menu screen is displayed, select ‘White Bal.’ by using the
Function Setup switch so that the arrow indicates ‘White Bal.’ .
2. Select a desired mode using the Function Setup switch.
COLOR CCD CAMERA
16 User Guide
MAIN SETUP
1.LENSDC
2.EXPOSURE 3.WHITE BALATW
4.BACKLIGHTOFF
* Select one of the following 5 modes, as appropriate for your purpose.
ATW : S elect this when the color temperature is between 1,800ºK and 10,500ºK
INDOOR : Select this when the color temperature is between 4,500ºK and 8,500ºK.
OUTDOOR : Select this when the color temperature is between 1,800ºK and 10,500ºK.
(sodium light inclusion)
AWC →SET : To find the optimal setting for the current luminance environment in this
mode, set the point the camera towards a sheet of white paper and press
the Function Setup switch. If the environment changes, readjust it.
MANUAL : S elect this to fine-tune White Balance
manually. Set White Balance first by using the
ATW or AWC mode. After that switch to
MANUAL mode, fine-tune the White Balance
and then press the Function Setup switch.
Notes
• White Balance may not work properly under the following conditions. In this case
select the AWC mode.
❶ When the color temperature of environment surrounding the subject is out of the
control range (e.g. clear sky, or sunset)
2 When the ambient illumination of the subject is dim.
3 If the camera is directed towards a fluorescent light or is installed in a place
where illumination changes dramatically, the White Balance operation may
become unstable.
COLOR CCD CAMERA
17 User Guide
Operating Your Camera
BACKLIGHT
This camera is designed so that it delivers a distinctive subject and background at
the same time, even when the subject is in backlight, unlike conventional cameras,
by adopting a proprietary SV-IV DSP chip.
1. When the SETUP menu screen is
MAIN SETUP
displayed, select ‘BACKLIGHT’ by using the
1.LENS
Function Setup switch so that the arrow
2.EXPOSURE
indicates ‘BACKLIGHT‘.
3.WHITE BAL
2. Select a desired mode using the Function
4.BACKLIGHT
Setup switch depending on the camera
5.SSNR
purpose.
BLC : Enables a user to directly select a desired area
from a picture, and to view the area more clearly.
• Select ‘BLC’ to adjust the area to be enhanced and
enhancement level.
WDR : When there are both bright and dark areas at
the same time, this mode makes both areas
distinctive.
DC
ATW
OFF
ON
• The WDR compensates for backlight more effectively than previous models,
by applying an optimum fusion ratio when combining the high speed shut
ter used in bright areas and the low speed shutter used in dark areas.
HLC(High
Light Compensation) :
If the scene contains extremely bright light areas such as; from car headlight,
the light can mask out much of the on-screen detail.
- DAY : in normal daylight conditions, the HLC is not activated.
- NIGHT : lf a high light that is larger than a certain size is present on the screen,
HLC is activated to remove the high light.
- HLC : Enable a user to select a mask color of high light area from a picture.
OFF : Not being used.
3. S elect a desired mode using the Function Setup switch and press the SET button.
Notes
WDR
OFF
• Select ‘WDR’ to adjust the WDR LIMIT and LEVEL.
- LIMIT : Adjust the WDR Sensitivity by selecting LOW,
MIDDLE, or HIGH.
- LEVEL : Adjust the WDR Brightness by controlling the
bar from 1 to 100.
COLOR CCD CAMERA
18 User Guide
• Since the following symptoms may occur according to the ambient illumination when
WDR is selected, set it to OFF.
❶ Color or screen changes unnaturally.
2 Noise appears in the bright part of the screen.
• Since the performance of the WDR function may be affected by the area of the bright part
of the screen, optimize the installation angle for the best WDR performance.
• If you increase LIMIT, the screen display may be distorted.
• In a dark environment, the HLC is only activated when a high light that is larger than a
certain area is present.
• The HLC is not activated in light or overly dark conditions.
COLOR CCD CAMERA
19 User Guide
Operating Your Camera
SSNR
DAY/NIGHT
This function reduces the background noise in a low luminance environment.
1. When the SETUP menu screen is displayed, select ‘SSNR’ by using the Function
Setup switch so that the arrow indicates ‘SSNR’ .
You can display pictures in color or black and white.
1. When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ by using the
Function Setup switch so that the arrow indicates ‘DAY/NIGHT’.
MAIN SETUP
1.LENSDC
2.EXPOSURE
3.WHITE BALATW
4.BACKLIGHTOFF
5.SSNRON
6.DAY/NIGHTAUTO
2. Select a desired mode using the Function Setup switch.
OFF : Deactivates SSNR. Noise is not reduced.
ON : Activates SSNR so that noise is reduced.
3. Set the SSNR mode to ‘ON’ and press the Function Setup switch. Then you can
adjust the noise reduction level.
2. S elect a desired mode using the Function Setup switch according to the picture
display you want.
Notes
• You cannot set the SSNR to ‘ON’ or ‘OFF’ when the AGC mode of the EXPOSURE
menu is ‘OFF’.
• When adjusting the noise reduction level of the SSNR mode, remember that the
higher the level set, the more the noise level will be reduced but that after image
may also occur.
COLOR CCD CAMERA
20 User Guide
MAIN SETUP
1.LENSDC
2.EXPOSURE 3.WHITE BALATW
4.BACKLIGHTOFF
5.SSNRON
6.DAY/NIGHT
AUTO
7.IMAGE ADJ COLOR : The picture is always displayed in color.
B/W : The picture is always displayed in black and
white. Please press SETUP button to turn on
or off the burst signal on B/W mode.
AUTO : The mode is switched to ‘Color’ in a normal
environment, but switches to ‘B/W’ mode
when ambient illumination is low. To set up
the switching time or speed for AUTO mode,
press the Function Setup switch.
- DWELL TIME : You can select the duration time about
changing the day/night mode.
→ 5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s
- DURATION : You can select brightness of illumination about changing the
day/night mode.
COLOR CCD CAMERA
21 User Guide
Operating Your Camera
Fast
Slow
Color → B/W
2.5 lux
0.8 lux
B/W → Color
4 lux
6 lux
* The brightness of illumination is changeable
by installed environment.
EXTERN : This mode allows you to apply a desired filter to external signals.
Notes
• You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is ‘OFF’.
At this time, the exchange between DAY mode and NIGHT mode operates as like
selecting ‘COLOR’ mode.
• The OSD key does not work for 3 seconds when switching to Color or B/W, to
ensure stable camera operation.
• The camera may focus less well under infrared illumination than under normal illumination.
IMAGE ADJ.
MAIN SETUP
1.LENSDC
2.EXPOSURE
3.WHITE BALATW
4.BACKLIGHTOFF
5.SSNRON
6.DAY/NIGHTAUTO
7.IMAGE ADJ
8.SPECIAL
2. Select a desired mode using the Function Setup switch.
COLOR CCD CAMERA
22 User Guide
IMAGE SETUP
V-REV
H-REV
D-ZOOM
SHARPNESS
PED LEVEL
RETURN
F REEZE : You can view still or moving pictures.
V-REV : You can flip the picture vertically on the
screen.
H-REV : You can flip the picture horizontally on
the screen.
D-ZOOM : You can use a digital zoom of x2~x10.
SHARPNESS :
1. When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by using the
Function Setup switch so that the arrow indicates ‘IMAGE ADJ.’
1.
2.
3.
4.
5.
6.
OFF
OFF
OFF
ON
0
As you increase this value, the picture outline
becomes stronger and clearer. Adjust this value
appropriately depending on the sharpness of
the picture.
PED LEVEL : P
lease use this menu item when
using a LCD monitor other than
standard ones. You can change
PED LEVEL.
RETURN : Select this to save the settings for the IMAGE ADJ. menu and to
return to the SETUP menu.
Notes
• When the V-REV or H-REV mode is enabled, the text on the screen does not flip.
• If you increase the SHARPNESS level too high, the picture may become distorted or
noise may appear.
COLOR CCD CAMERA
23 User Guide
Operating Your Camera
Notes
SPECIAL
• When the
・ the CAM
CAMTITLE
TITLEmenu
menuis is ヤOFFユ,
‘OFF’, no title
no
title will
will
be displayed
be displayed
ononthe
themonitor
monitorscreen
screen
even if you enter one.
• Only English is available in this mode.
1. When the SETUP menu screen is displayed, select ‘SPECIAL’ by using the Function
Setup switch so that the arrow indicates ‘SPECIAL’.
MAIN SETUP
1.LENS DC
2.EXPOSURE
3.WHITE BAL ATW
4.BACKLIGHT OFF
5.SSNR ON
6.DAY/NIGHT AUTO
7.IMAGE ADJ
8.SPECIAL
9.EXIT
1.
2.
3.
4.
5.
SPECIAL
CAM TITLE
SYNC
MOTION DET
PRIVACY
DIS
OFF
INT
OFF
OFF
OFF
3 Press the Function Setup switch.
CAMERA TITLE SETUP
ABCDEFGHIJKLM
NOPQRSTUVWXYZ
abcdefghijklm
nopqrstuvwxyz
-.0123456789
←→ CLR POS END
2. Select a desired mode using the Function Setup switch.
1.
2.
3.
4.
5.
6.
7.
8.
9.
SPECIAL
CAM TITLE
SYNC
MOTION DET
PRIVACY
DIS
COMM ADJ
LANGUAGE
RESET
RETURN
Notes
• If you move the cursor to CLR and press the Function Setup switch, all the letters
are deleted. To edit a letter, change the cursor to the bottom left arrow and press
the Function Setup switch. Move the cursor over the letter to be edited, move the
cursor to the letter to be inserted and then press the Function Setup switch.
ENGLISH
CAM TITLE : If you enter a title, the title will appear on the monitor.
24 User Guide
4 Use the Function Setup switch to move to a desired letter and select the letter
by pressing the Function Setup switch. Repeat this to enter multiple letters.
You can enter up to 15 letters.
OFF
INT
OFF
OFF
OFF
❶ If the SPECIAL menu screen is displayed, use the Function Setup switch so
that the arrow indicates ‘CAM TITLE’.
2 Set it to ‘ON’ by using the Function Setup switch.
COLOR CCD CAMERA
5 Enter
a title, move the cursor to ‘POS’ and press
the Function Setup switch. The entered title
appears on the screen. Select the position to
display the title on the screen by using the
Function Setup switch and press. When the
position is determined, select ‘END’ and press the
Function Setup switch to return to the SPECIAL
menu.
COLOR CCD CAMERA
25 User Guide
FRONT DOOR
Operating Your Camera
SYNC : In areas where the supply is at 60Hz, you can
synchronize the output phase of multiple cameras
using the power synchronization function (LineLock) without using a synchronization signal
generator.
- INT : Internal Synchronization Type
- L/L : Power Synchronization Type, Line-lock
• Press the Function Setup switch.
• You can select a desired phase from 0 to 359 when select 'phase'.
• You can decide the synchronization between luminance and color signal when
select the 'Mode' to TRACE.
Notes
• When using AC power at 60Hz frequency, you can use the L/L type synchronization.
• When the power is DC 12V, the SYNC menu is fixed to the ‘INT’ mode.
M
OTION DET: You can monitor activity more efficiently, because a
signal is generated by the camera whenever
motion is detected.
❶ When the SPECIAL menu screen is displayed, press the Function Setup
switch so that the arrow indicates ‘MOTION DET’.
2 Set up the mode using the Function Setup switch.
- SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high,
motion detection sensitivity is increased to recognize even small
movement.
- AREA MODE : Determines whether to use the MD area selected in SENSITIVITY.
- SEL POS : Determines which of the 4 vertices of each MD area is to be used.
- YPOS : Determines the coordinate of the vertical axis for SEL POS.
- XPOS : Determines the coordinate of the horizontal axis for SEL POS.
- FILL → SET : Fills in a selected MD area. Fills in a selected MD area. The color of filling
is sequentially selected as brown, orange, blue, cyan, yellowish green,
yellow and red.
- RETURN : Select this to save the MOTION DET menu settings and return to the SPECIAL
menu.
COLOR CCD CAMERA
26 User Guide
Notes
• MD areas show only MOTION DET menu. Therefore, MD areas don’t display on the
monitor screen.
• When motion is detected, “MOTION DETECTION” expression is displayed on the screen.
P RIVACY :H
ide an area you want to hide on the
screen.
❶ When the SPECIAL menu screen is displayed,
press the Function Setup switch so that the
arrow indicates ‘PRIVACY’.
2 Set up the mode using the Function Setup
switch.
- AREA SEL : You can select up to 8 PRIVACY areas.
- AREA MODE : D
etermines whether to use the area
selected in the AREA SEL, and the
size and position of the area.
- MASK COLOR : D
etermine area color. You can select Gray, Green, Red, Blue, Black,
White.
- TRANSP : Determine the transparency of selected area as controlling number
from 0 to 3.
- RETURN : S elect this to save the PRIVACY menu settings and return to the
SPECIAL menu.
DIS (Digital Image Stabilizer) :
This function mitigates any picture movement due to external factors such as
wind.
Notes
• The chance of resolution decrease is existed because DIS function uses the digital zoom.
• DIS doesn’t operate when background illumination is too low.
• DIS doesn’t operate when object pattern is monotonic as like sky or white wall.
• If DIS is enabled, the digital zoom is configured to less than 46 level.
COLOR CCD CAMERA
27 User Guide
Operating Your Camera
OMM ADJ (Communication Adjustment) :
C
This function sets up the camera communication status when controlling the
camera through an external control device.
❶ When the SPECIAL menu screen is displayed, press the Function Setup
switch so that the arrow indicates ‘COMM ADJ’.
2 Set up the mode using the Function Setup switch.
Troubleshooting
Refer to the following table if you are experiencing trouble with your camera.
Contact an authorized technician if the table does not provide you with a
solution to the trouble.
● Nothing appears on the screen.
▶ Check that the power cord and line connection between the camera and monitor are fixed properly.
▶ Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
● The image on the screen is dim.
▶ Is lens stained with dirt? Clean your lens with soft, clean cloth.
▶ Set the monitor to proper condition.
▶ If the camera is exposed to too strong light, change the camera position.
● The image on the screen is dark.
▶ Adjust the contrast feature of the monitor.
▶ If you have an intermediate device, set the 75Ω / Hi-z properly.
● The camera is not working properly, and the surface of the camera is hot.
▶ Check that you have properly connected the camera to an appropriate power source.
- CAM ID : Determines the camera's identification number (between 0 and 255).
- BAUD RATE : You can select 2400/4800/9600/19200/38400/57600 bps.
- UART MODE : You can select NONE, EVEN or ODD for the parity bits.
- RET PKT : Determines whether to send a command back to the controller device
when a communication control command is sent to the camera.
- DISP CAM ID : Display camera title on top left corner of the screen.
Camera ID
1
BAUD RATE
9600
UART MODE
8-NONE-1
▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
● The SENS-UP function does not work.
▶ Check that AGC of EXPOSURE SETUP menu is ‘OFF’.
▶ Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ .
● The Motion Detection function does not work.
▶ Check that MOTION DEF of SPECIAL SETUP menu is ‘OFF’.
● Color is not correct.
* Initial value of communication adjustment
Item
Initial value
● The DAY/NIGHT menu does not work.
PET PKT
ENABLE
▶ Check the setting of WHITE BAL SETUP menu .
● The screen flickers continually.
▶ Check that direction of camera turns toward the Sun.
LANGUAGE : You can select the menu language according to your
requirements.
RESET : Resets the camera settings to the factory defaults.
RETURN : S elect this to save the SPECIAL menu settings and return to the MAIN SETUP
menu.
EXIT
Press the Function Setup switch in the EXIT menu to save the current settings and exit the
MAIN SETUP menu.
COLOR CCD CAMERA
28 User Guide
● RS-485 communication fails.
▶ Check the polarity between RS-485 Control Port and RS-485 cable.
485 Control Board Connection Port
(+) CONNECTION TERMINAL (TRX+)
( - ) CONNECTION TERMINAL (TRX-)
RS-485 Control Port
485+
485-
▶ Check the RS-485 Communication establishment initial value
* RS-485 Communication establishment initial value
Item
Camera ID BAUD RATE UART MODE
Initial value
1
9600
8-NONE-1
RET PKT
ENABLE
▶ We recommend that you make ground connect between camera and controller in order to maintain
safety communication control.
COLOR CCD CAMERA
29 User Guide
DECLARATION OF CONFORMITY
Specifications
SVD-4600(W)N
POWER
CCD
Sync
Input voltage
Power consumption
Size
Diagonal 6mm (1/3") Sony DS CCD
Total Pixels
Effective Pixels
Scanning System
Synchronization
Frequency
811(H) x 508(V)
768(H) x 494(V)
O.S.D
E
L
E
C
T
R
I
C
A
L
SVD-4600(W)P
AC24V / DC12V
3.5W
Back-light Compensation
Resolution
S/N (Y signal)
Min. Illumination
White Balance
Electronic Shutter Speed
Sens-up
Gain Control
SSNR
Motion Detection
PRIVACY
V-REV (Mirror)
H-REV (Flip)
FREEZE
SHARPNESS
IRIS Control
Day & Night
DIS
Digital Zoom
Communication
Built-in Lens
Angle of view
Monitoring angle
Horizontal
Vertical
PAN
TILT
Weather Proof
Operating
Temperature/Humidity
Storage Temperature/Humidity
Dimension
Weight
795(H) x 595(V)
752(H) x 582(V)
2:1 Interlace
Internal / Line Lock
H : 15.734KHz / V : 59.94Hz
H : 15.625KHz / V : 50.00Hz
Korean, English, Japanese,
English, French, Germany, Spanish,
French, Spanish, Portuguese
Italy, Chinese, Portuguese
WDR / HLC / BLC / OFF
Color : 560 TV Lines↑ B/W : 700 TV Lines↑
52 dB (AGC Off, Weight ON)
0.001 Lux (Color Sens-up), 0.00004 Lux (B/W Sens-up) at F1.2
ATW / AWC / Manual / Outdoor / Indoor (1800°K ~10,500°K)
Fixed (1/60 or Flickerless Mode)
Fixed (1/50 or Flickerless Mode)
AUTO / OFF (Selectable limit x2 ~ x256)
LOW/HIGH/OFF
ON / OFF (1~32 Level)
ON / OFF (8 Zone)
ON / OFF (8 Zone)
ON / OFF
ON / OFF
ON / OFF
ON / OFF (Level Adjustable)
DC drive Lens
COLOR / Black & White / AUTO
ON / OFF
ON / OFF (x10)
RS-485 (2400, 4800, 9600, 19200, 38400, 57600 bps selectable)
(STW Protocol, Pelco-D Protocol available)
x3.6 Vari-focal Lens (F1.2 f2.8~10.0mm)
94.4° ~ 28°
69.2° ~ 21°
Manual 0°~ 340°
Manual 0°~ 146°
IP66
-10° to +50° / 30% to 80% RH
※ SVD-4600WN, SVD-4600WP : Ivory color base model
85mm
85mm
COLOR CCD CAMERA
30 User Guide
46mm
126mm
85mm
Ø 148mm
83.5mm
89 / 336 / EEC
Manufacturer's Name SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-716
European Representative Name
European Representative Address
Equipment Type/Environment CCTV Camera
Model Name SVD-4600P/WP
Beginning Serial NO. S8080001
Year of Manufacture 2008. 12. 01
Conformance to EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
20° to +60° / 20% to 90% RH
Ø148 x 126 mm
1.3Kg
Dimension
Application of Council Directive(s)
Manufacturer SAMSUNG TECHWIN CO., LTD Legal Representative in Europe
Signature Signature
Full Name BONJENG GU
Full Name Position QUALITY CONTROL MANAGER Position Place CHANGWON, KOREA
Place
Date 2008. 12. 01
Date
COLOR CCD CAMERA
31 User Guide
SALES NETWORK
•
AMSUNG TECHWIN CO., LTD.
S
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703
TEL : +82-31-740-8151~8 FAX : +82-31-740-8145
•
AMSUNG TECHWIN AMERICA Inc.
S
1480 Charles Willard St, Carson, CA 90746, UNITED STATES
Tol Free : +1-877-213-1222 FAX : +1-310-632-2195
www.samsungcctvusa.com
•
AMSUNG TECHWIN EUROPE CO., LTD.
S
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS
TEL : +44-1932-45-5300 FAX : +44-1932-45-5325
www.samsungtechwin.com
www.samsungcctv.com
P/No. : Z6806-0869-01C
VAN 09. 10