Version 1.0 | 2013/08/15
User Manual
Wireless AC Day/Night Camera with Color Night Vision
DCS-2136L
Manual Overview
D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or
organization of such revisions or changes. Information in this document may become obsolete as our services and websites develop and
change. Please refer to the www.mydlink.com website for the most current information.
Manual Revisions
Revision
Date
1.0
August 15, 2013
Description
DCS-2136L Revision A1 with firmware version 1.00
Trademarks
D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries.
All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.
Copyright © 2013 D-Link Corporation.
All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation.
D-Link DCS-2136L User Manual
2
Table of Contents
Product Overview....................................................................... 5
Package Contents.................................................................. 5
Introduction............................................................................. 7
Features..................................................................................... 8
Hardware Overview.............................................................. 9
Front....................................................................................... 9
Rear.......................................................................................10
Sides.....................................................................................11
Zero Configuration Setup.................................................13
Camera Setup Wizard.........................................................17
Windows Users.................................................................17
Mac Users............................................................................18
Manual Hardware Installation.........................................19
Installation...................................................................................20
Wireless Installation Considerations.............................20
WPS - Push Button Setup..................................................21
mydlink..........................................................................................22
Configuration..............................................................................23
Configuration Utility...........................................................23
Live Video...............................................................................24
Setup........................................................................................26
Setup Wizard.....................................................................26
Network Setup..................................................................32
Wireless Setup...................................................................35
Dynamic DNS....................................................................36
D-Link DCS-2136L User Manual
Image Setup......................................................................37
Audio and Video...............................................................39
Preset....................................................................................41
Motion Detection............................................................43
Time and Date...................................................................44
Event Setup........................................................................45
SD Card................................................................................53
Advanced................................................................................54
Digital Input/Output.......................................................54
ICR and White LED Light................................................55
HTTPS...................................................................................56
Access List...........................................................................57
Maintenance..........................................................................58
Device Management......................................................58
System.................................................................................59
Firmware Upgrade...........................................................60
Status.......................................................................................61
Device Info.........................................................................61
Logs......................................................................................62
Help......................................................................................63
DI/DO Specifications................................................................64
Technical Specifications.........................................................65
Safety Statements....................................................................68
3
Section 1: Product Overview
Product Overview
Package Contents
DCS-2136L Wireless AC Day/Night Camera with Color Night Vision
CAT5 Ethernet cable
Power adapter
CD-ROM with User Manual and software
Quick Installation Guide
If any of the above items are missing, please contact your reseller.
Note: Using a power supply with a different voltage than the one included with your
product will cause damage and void the warranty for this product.
D-Link DCS-2136L User Manual
4
Section 1: Product Overview
System Requirements
Network Requirements
CD Setup Wizard Requirements
Web-based Configuration Utility
Requirements
• 10/100 Ethernet network or an 802.11ac/n/g/b wireless network
Computer with the following:
• A PC with a wired connection to your router
• Windows® 8 (32/64bit), Windows® 7 (32/64bit), XP (32/64bit),Vista® (32/64bit), Mac
OS®X 10.5 or above
•An Internet connection
•A router connected to your broadband modem
Browser Requirements:
• Internet Explorer 7 or higher
• Firefox 12 or higher
• Safari 4 or higher
• Chrome 20 or higher
Note: Make sure you have the latest version of Java installed.
Visit www.java.com to download the latest version.
mydlink Website Requirements
D-Link DCS-2136L User Manual
• Broadband Internet connection
• Computer with:
• Internet Explorer 7 or higher (ActiveX)
• Firefox 12 or higher
• Safari 4 or higher
• Chrome 20 or higher
5
Section 1: Product Overview
Introduction
Congratulations on your purchase of the DCS-2136L Wireless AC Day/Night Camera with Color Night Vision. The DCS-2136L is
a versatile and unique solution for your small office or home. Unlike a standard webcam, the DCS-2136L is a complete system
with a built-in CPU and web server that transmits high quality video images for security and surveillance. The DCS-2136L
can be accessed remotely, and controlled from any PC/Notebook over your local network or through the Internet via a web
browser. The simple installation and intuitive web-based interface offer easy integration with your Ethernet/Fast Ethernet
or 802.11ac/n/g wireless network. The DCS-2136L also comes with remote monitoring and motion detection features for a
complete and cost-effective home security solution.
D-Link DCS-2136L User Manual
6
Section 1: Product Overview
Features
Simple to Use
The DCS-2136L is a stand-alone system with a built-in CPU, requiring no special hardware or software. The DCS-2136L supports both ActiveX mode
for Internet Explorer and Java mode for other browsers such as Chrome®, Firefox®, and Safari®.
Supports a Variety of Platforms
Supports TCP/IP networking, HTTP, and other Internet related protocols. The DCS-2136L can also be integrated easily into other Internet/Intranet
applications because of its standards-based features.
Web Configuration
Using a standard Web browser, administrators can configure and manage the DCS-2136L directly from its own Web page via Intranet or Internet.
This means you can access your DCS-2136L anytime, anywhere in the world.
All-Day Surveillance with low light color image capability
A built-in white light LED lets you monitor an area 24 hours a day with full color images, even in areas with low light or complete darkness. Combined
with the passive IR sensor which can be used to trigger the white light LED, the DCS-2136L is a versatile surveillance and security monitoring device.
Broad Range of Applications
With today’s high-speed Internet services, the DCS-2136L can provide the ideal solution for delivering live video images over the Intranet and
Internet for remote monitoring. The DCS-2136L allows remote access using a Web browser for live image viewing, and allows the administrator to
manage and control the DCS-2136L anytime, anywhere in the world. Many applications exist, including industrial and public monitoring of homes,
offices, banks, hospitals, child-care centers, and amusement parks.
802.11ac Wireless or Ethernet/Fast Ethernet Support
The DCS-2136L offers wireless 802.11ac and Ethernet/Fast Ethernet connectivity, making the DCS-2136L easy to integrate into your existing network
environment. The DCS-2136L works with 10/100/1000Mbps Ethernet based networks for traditional wired environments, and works with 802.11ac
routers or access points for added flexibility. The Site Survey feature also allows you to view and connect to any available wireless networks.
Remote Monitoring Utility
The D-ViewCam application adds enhanced features and functionality for the DCS-2136L and allows administrators to configure and access the
DCS-2136L from a remote site via Intranet or Internet. Other features include image monitoring, recording images to a hard drive, viewing up to
32 cameras on one screen, and taking snapshots.
D-Link DCS-2136L User Manual
7
Section 1: Product Overview
Hardware Overview
Front
5
1
2
3
6
4
1
Power/Link LED
Indicates the camera's current status
2
WPS Status LED
Indicates the WPS connection status of the camera
3
White Light LED
Used to illuminate the camera's field of view at night
4
PIR Sensor
5
Camera Lens
Records video of the surrounding area
6
Microphone
Records audio from the surrounding area
D-Link DCS-2136L User Manual
Passive Infrared sensor for motion detection
8
Section 1: Product Overview
Rear
1
5
6
2
3
7
4
1
Ethernet Port
2
Speaker
3
WPS Button
Press this button, then press the WPS button for 5 seconds on your router to set up
a wireless connection automatically
4
Reset Button
Press and hold this button for 10 seconds to reset the camera
5
Power Connector
Connects to the included DC 5 V power adapter
6
DI/DO Connector
I/O connectors for external devices
7
Adjustment Ring
Tighten or loosen the adjustment ring to adjust the camera's position
D-Link DCS-2136L User Manual
RJ45 connector for Ethernet
Audio output
9
Section 1: Product Overview
Sides
1
1
Micro SD Card Slot
D-Link DCS-2136L User Manual
Insert a MicroSD card for Local storage for storing recorded image and video
10
Section 2: Installation
Software Installation
There are three ways to set up your camera:
Zero Configuration Setup: If you have a mydlink-enabled router, this is the easiest way to set up your camera.
Refer to page 12.
Camera Setup Wizard: If you do not have a mydlink-enabled router, use the Camera Installation Wizard to guide
you through setup and initial configuration of your camera. Refer to page 16.
Manual Hardware Installation: This section shows you how to manually set up your camera, though in order to
use the mydlink features of your camera, you will still need to run the Camera Installation Wizard. Refer to page 18.
D-Link DCS-2136L User Manual
11
Section 2: Installation
Zero Configuration Setup
If you have a D-Link Cloud Router, you can take advantage of Zero Configuration. Zero Configuration automatically configures
your camera's settings for you, and adds it to your mydlink account automatically. This type of setup allows you to set up your
camera by simply plugging it in and connecting it to your router.
Connect your camera to your mydlink enabled cloud router and Zero Configuration will automatically configure your
DCS-2136L and automatically add the camera to your mydlink account. You can now remotely access your camera from the
mydlink.com website to manage and monitor your DCS-2136L.
Connect the Ethernet Cable
If using an Ethernet connection: Connect the included Ethernet cable to the
Ethernet port located on the back of the DCS-2136L and connect it to your router.
Attach the External Power Supply
Attach the external power supply to the DC Power receptor located on the rear
panel of the DCS-2136L and connect it to your wall outlet or power strip.
D-Link DCS-2136L User Manual
12
Section 2: Installation
Optional: WPS Wireless Connection
Alternatively, if your router supports WPS, you can use the WPS
button on the camera to easily create a secure wireless connection
to your network.
To create a WPS connection:
Step 1
Press and hold the WPS button for approximately 5-6 seconds. The
blue WPS status LED above the button will blink.
Step 2
Within 60 seconds press the WPS button on your router. On some
routers, you may need to log in to the web interface and click on
an on-screen button to activate the WPS feature. If you are not sure
where the WPS button is on your router, please refer to your router’s
User Manual.
The DCS-2136L will automatically create a wireless connection to
your router. While connecting, the status LED will flash. When the
connection process is complete, the status LED will turn solid.
WPS Button
Note: If your router does not support WPS, you can still use the wired
connection method on the previous page. After Zero Configuration
setup is complete, your router's wireless settings will be automatically
transferred to the camera.
D-Link DCS-2136L User Manual
13
Section 2: Installation
Check Your mydlink Account
From any computer, open a web browser, go to http://www.mydlink.
com and log into your account. Once mydlink detects your camera,
a New Device Found! notice will appear in the bottom-left corner.
Click on the device name to continue.
A summary and confirmation notification will appear with the
automatically configured details. Make a note of the details and click
OK to add the camera to your account.
D-Link DCS-2136L User Manual
14
Section 2: Installation
Zero Configuration is now complete and your camera has been
added to your mydlink account. You can now view your camera on
the mydlink Live View tab.
If you wish to connect your camera to your router wirelessly, you
can simply disconnect the Ethernet cable and move the camera
to its intended location; your router's wireless settings have been
automatically transferred to the camera, and no further configuration
is required.
Your camera is now set up, and you can skip to "mydlink" on page
21 to learn more about the mydlink features of this camera, or to
"Configuration" on page 22 for advanced configuration of your camera.
D-Link DCS-2136L User Manual
15
Section 2: Installation
Camera Setup Wizard
If you do not have a mydlink-enabled Cloud Router, you can use the Camera Setup Wizard to guide you through the process
of adding your camera to the mydlink service.
Windows Users
Insert the Installation CD-ROM into your computer’s optical drive to start the autorun program. If the autorun
program does not open, go to My Computer, browse to your CD drive, and double-click on the autorun.exe file.
Once the wizard has started simply click Set up your Cloud Camera to go through the Setup Wizard, which will
guide you step-by-step through the installation process from connecting your hardware to configuring your
camera and registering it with your mydlink account.
D-Link DCS-2136L User Manual
16
Section 2: Installation
Mac Users
Insert the Installation CD-ROM into your computer’s optical drive. On the desktop, open your
CD drive and double-click on the SetupWizard file.
After about 20-30 seconds, the Setup Wizard will open, which will guide you step-by-step through the installation process
from connecting your hardware to configuring your camera and registering it with your mydlink account.
D-Link DCS-2136L User Manual
17
Section 2: Installation
Manual Hardware Installation
If you wish to set up your camera without using the Camera Setup Wizard, please follow these steps.
Note: In order to use the mydlink features of this product, you will need to go through the Camera Setup Wizard.
Attach the External Power Supply
Attach the external power supply to the DC Power receptor located on the rear
panel of the DCS-2136L and connect it to your wall outlet or power strip.
Connect the Ethernet Cable
Connect the included Ethernet cable to the network cable connector located on
the panel at the rear of the DCS-2136L and attach it to the network.
D-Link DCS-2136L User Manual
18
Section 2: Installation
Installation
Wireless Installation Considerations
This D-Link device can connect to your wireless network from anywhere within the operating range of your wireless network. However, the number,
thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary
depending on the types of materials and background RF (radio frequency) noise in your home or business. The key to maximizing wireless range
is to follow these basic guidelines:
1. Minimize the number of walls and ceilings between your adapter and other network devices (such as your DCS-2136L) - each wall or ceiling
can reduce your adapter’s range from 3-90 feet (1-30 meters).
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree angle appears to be almost 3 feet
(1 meter) thick. At a 2-degree angle, it looks over 42 feet (14 meters) thick. Position your devices so that the signal will travel straight through
a wall or ceiling (instead of at an angle) for better reception.
3. Building Materials make a difference. A solid metal door or aluminum studs may weaken the wireless signal. Try to position your access points,
wireless routers, and other networking devices where the signal passes through drywall or open doorways. Materials and objects such as
glass, steel, metal, walls with insulation, water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your product at least 3-6 feet or 1-2 meters away from electrical devices or appliances that generate RF noise.
5. If you are using 2.4GHz cordless phones or other radio frequency sources (such as microwave ovens), your wireless connection may degrade
dramatically or drop completely. Make sure your 2.4GHz phone base is as far away from your wireless devices as possible. The base transmits
a signal even if the phone in not in use.
D-Link DCS-2136L User Manual
19
Section 2: Installation
WPS - Push Button Setup
If your router supports WPS, you can use the WPS button on the camera to easily create a secure wireless connection to your
network.
To create a WPS connection:
Step 1
Press and hold the WPS button for approximately 5-6 seconds. The
blue WPS status LED above the button will blink.
Step 2
Within 60 seconds press the WPS button on your router. On some
routers, you may need to log in to the web interface and click on
an on-screen button to activate the WPS feature. If you are not sure
where the WPS button is on your router, please refer to your router’s
User Manual.
The DCS-2136L will automatically create a wireless connection to
your router. While connecting, the status LED will flash. When the
connection process is complete, the status LED will turn solid.
WPS Button
D-Link DCS-2136L User Manual
20
Section 3: mydlink
mydlink
After registering your DCS-2136L camera with a mydlink account in the Camera Setup Wizard. You will be able to remotely
access your camera from the www.mydlink.com website. After signing in to your mydlink account, you will see a screen similar
to the following:
For more details on using your camera with mydlink, go to the Support section of the mydlink website and check the User
Manual section for your product to find the latest instruction guide for your camera's mydlink features.
D-Link DCS-2136L User Manual
21
Section 4: Configuration
Configuration
Configuration Utility
After completing the Camera Installation Wizard, you are ready to use your camera. The camera’s built-in Web configuration
interface is designed to allow you to easily access and configure your DCS-2136L. At the end of the wizard, enter the IP address
of your camera into a web browser, such as Internet Explorer®. To log in, use the User name admin and the password you created
in the Installation Wizard. If you did not create a password, the default password is blank. After entering your password, click OK.
Note: If you are directly connecting your PC to the camera, or if you are using the camera on a closed network, the default IP
is 192.168.0.20.
D-Link DCS-2136L User Manual
22
Section 4: Configuration
Live Video
This section shows your camera’s live video. You may select any of the
available icons listed below to operate the camera. You may also select
your language using the drop-down menu on the left side of the screen.
You can zoom in and out on the live video image using your mouse.
Right-click to zoom out or left-click to zoom in on the image.
SD Status: This option displays the status of the SD card. If no
SD card has been inserted, this screen will display the
message "Card Invalid."
IO Status: This option displays the status of your I/O device if a
device has been connected.
Digital Input
Indicator
Motion Trigger
Indicator
Recording
Indicator
White Light LED
This indicator will change color when a digital input signal is detected.
This indicator will change color when a trigger event occurs.
Note: The video motion feature for your camera must be enabled.
When a recording is in progress, this indicator will change color.
This button will enable or disable the white light LED. This may change depending
on the setting configured in "White LED Light" on page 54
Stop
This control pad can be used to electronically pan, tilt, and zoom (ePTZ) within the
camera's predefined view area, if one has been defined.
Starts the automatic panning function. The ROI will pan from back and forth within
the FOV
Stops automatic panning.
Preset Path
Starts the camera's motion along the predefined path.
Control Pad
Auto Pan
D-Link DCS-2136L User Manual
23
Section 4: Configuration
ePTZ Speed: You may select a value between 0 and 64. 0 is the
slowest and 64 is the fastest.
Global View: This window indicates the total field of view (FOV) of
the camera. The red box indicates the visible region of
interest (ROI).
Language: You may select the interface language using this menu.
Go To: If any presets have been defined, selecting a preset
(Preset List) from this list will display it.
D-Link DCS-2136L User Manual
Video Profile 1
Record a Video Clip
Video Profile 2
Set a Storage Folder
Video Profile 3
Listen/Stop Audio In (from microphone)
Full screen mode
Start/Stop Audio Out (to speaker)
Taking a Snapshot
Start/Stop Digital Output
24
Section 4: Configuration
Setup
Setup Wizard
This section allows you to begin setup wizards which will guide you through the process of getting your camera’s various functions configured. If
you comfortable with adjusting the settings manually, you may skip the wizards and adjust the necessary as needed.
Internet You may choose to configure your network by using
Connection the Internet Connection Setup Wizard that includes
Setup Wizard: step-by-step instructions. Please refer to page "Internet
Connection Setup Wizard" on page 26 for more details.
Manual
Internet
Connection
Setup:
If you would rather manually setup the camera internet
connection, you can refer to page "Network Setup" on
page 31 which provides more details on the information
required.
Motion You may choose to configure motion detection by
Detection Setup using the Motion Detection Setup Wizard that includes
Wizard: step-by-step instructions. Please refer to page "Motion
Detection Setup Wizard" on page 29 for more details.
Manual
Motion
Detection
Setup:
If you would rather manually setup the camera’s
motion detection features, you can refer to page
"Motion Detection" on page 42 which provides more
details on the information required.
D-Link DCS-2136L User Manual
25
Section 4: Configuration
Internet Connection Setup Wizard
This wizard will guide you through a step-by-step process to configure your
new D-Link Camera and connect the camera to the Internet. Note that this
wizard will not register your camera with mydlink.com.
Click Next to continue.
Select Automatic IP Address if you want your DHCP server (usually
enabled on your router) to assign the camera its IP settings. If you want
to manually assign the IP settings, select Static IP Address and enter the
following details:
IP Address: Enter an IP address for your camera.
Subnet Mask: Enter the subnet mask of your network.
Default Enter the default gateway address. This is usually the IP
Gateway: address of your router.
Primary DNS: Enter the primary DNS server’s IP address. This is usually
the IP address of your router.
Secondary DNS: Enter the secondary DNS server’s IP address. This is
optional.
If you are required to connect using PPPoE, select Enabled and enter the
Username and Password for your PPPoE connection. Only select this option
if your camera is directly connected to your broadband modem. If it is on
a network with a router or gateway, do not select this option.
Click Next to continue.
D-Link DCS-2136L User Manual
26
Section 4: Configuration
A Dynamic DNS account allows you to access your camera over the Internet
when you have an IP address that changes each time you connect to the
Internet. If you have a Dynamic DNS account, click Enable and enter the
following details:
Enable: Click to enable the DDNS function.
DDNS: (Dynamic Domain Name Server) will hold a DNS host
name and synchronize the public IP address of the
modem when it has been modified. The username and
password are required when using the DDNS service.
Server Address: Select your Dynamic DNS Server from the drop down
menu.
Host Name: Enter the host name of the DDNS server.
User Name: Enter your username or e-mail address used to connect
to the DDNS.
Password: Enter your password used to connect to the DDNS
server.
Timeout: You can setup how often the camera notifies the DDNS
server of its current global IP address by entering a
whole number in hours.
Click Next to continue.
D-Link DCS-2136L User Manual
27
Section 4: Configuration
Create a unique name for your camera. Click Next to continue.
Select the time zone that the camera is geographically located in so that
scheduled events occur at the correct time. If your time zone observes
daylight saving, check the Enable Daylight Saving box and select Auto
Daylight Saving to have DST set automatically or select Set date and
time manually to enable the drop-down menu so that you can set the
start and end time of daylight saving yourself.
Click Next to continue.
A summary of the options you selected is displayed for confirmation. If
you are happy with the selected configuration, click Apply otherwise click
Back to make the required changes.
D-Link DCS-2136L User Manual
28
Section 4: Configuration
Motion Detection Setup Wizard
This wizard will guide you through a step-by-step process to configure
your camera's motion detection functions.
Click Next to continue.
Step 1
This step will allow you to enable or disable motion detection, specify the
detection sensitivity, and adjust the camera’s ability to detect movement.
You may specify whether the camera should capture a snapshot or a
video clip when motion is detected.
Please see the Motion Detection section on "Motion Detection" on page
42for information about how to configure motion detection.
Step 2
This step allows you to enable motion detection based on a customized
schedule. Specify the day and hours. You may also choose to always
record whenever motion is detected.
D-Link DCS-2136L User Manual
29
Section 4: Configuration
Step 3
This step allows you to specify how you will receive event notifications
from your camera. You may choose not to receive notifications, or to
receive notifications via e-mail or FTP.
Please enter the relevant information for your e-mail or FTP account.
Click Next to continue.
Step 4
You have completed the Motion Detection Wizard.
Please verify your settings and click Apply to save them.
Please wait a few moments while the camera saves your settings and
restarts.
D-Link DCS-2136L User Manual
30
Section 4: Configuration
Network Setup
Use this section to configure the network connections for your camera.
All relevant information must be entered accurately. After making any
changes, click the Save Settings button to save your changes.
LAN Settings: This section lets you configure settings for your local
area network.
DHCP: Select this connection if you have a DHCP server
running on your network and would like your camera
to obtain an IP address automatically.
Static IP You may obtain a static or fixed IP address and other
Address: network information from your network administrator
for your camera.
IP Address: Enter the fixed IP address in this field.
Subnet Mask: This number is used to determine if the destination is
in the same subnet. The default value is 255.255.255.0.
Default Gateway: The gateway used to forward data to.
Primary DNS: The primary domain name server translates names to
IP addresses.
Secondary DNS: The secondary DNS acts as a backup to the primary.
Enable UPnP Enabling this setting allows your camera to be
Presentation: configured as a UPnP device on your network.
Enable UPnP Enabling this setting allows the camera to add port
Port Forwarding: forwarding entries into the router automatically on a
UPnP capable network.
D-Link DCS-2136L User Manual
31
Section 4: Configuration
Enable PPPoE: Enable this setting if your network uses PPPoE.
User Name / Enter the username and password for your PPPoE
Password: account. Re-enter your password in the Confirm
Password field. You may obtain this information from
your ISP.
HTTP Port: The default port number is 80.
Access Name for The default name is video#.mjpg, where # is the
Stream 1~3: number of the stream.
HTTPS Port: You may use a PC with a secure browser to connect to
the HTTPS port of the camera. The default port number
is 443.
RTSP Port: The port number that you use for RTSP streaming
to mobile devices, such as mobile phones or PDAs.
The default port number is 554. You may specify the
address of a particular stream. For instance, live1.sdp
can be accessed at rtsp://x.x.x.x/video1.sdp where the
x.x.x.x represents the ip address of your camera.
Enable CoS: Enabling the Class of Service setting implements a
best-effort policy without making any bandwidth
reservations.
Enable QoS: Enabling QoS allows you to specify a traffic priority
policy to ensure a consistent Quality of Service during
busy periods. If the DCS-2136L is connected to a router
that itself implements QoS, the router's settings will
override the QoS settings of the camera.
D-Link DCS-2136L User Manual
32
Section 4: Configuration
Enable IPV6: Enable the IPV6 setting to use the IPV6 protocol.
Enabling the option allows you to manually set up
the address, specify an optional IP address, specify an
optional router and an optional primary DNS.
Enable The DCS-2136L allows you to multicast each of the
Multicast for available streams via group address and specify the TTL
stream value for each stream. Enter the port and TTL settings
you wish to use if you do not want to use the defaults.
Please verify your settings and click Save Settings to
commit them.
D-Link DCS-2136L User Manual
33
Section 4: Configuration
Wireless Setup
This section allows you to set up and configure the wireless settings on
your camera. After making any changes, click the Save Settings button to
save your changes.
Site Survey: Click the Rescan button to scan for available wireless
networks. After scanning, you can use the drop-down
box to select an available wireless network. The related
information (SSID,Wireless Mode, Channel, Authentication,
Encryption) will be automatically filled in for you.
SSID: Enter the SSID of the wireless access point you wish to
use.
Wireless Mode: Use the drop-down box to select the mode of the
wireless network you wish to connect to. Infrastructure
is normally used to connect to an access point or
router. Ad-Hoc is usually used to connect directly to
another computer.
Channel: If you are using Ad Hoc mode, select the channel of the
wireless network you wish to connect to, or select Auto.
Authentication: Select the authentication you use on your wireless
network - Open, Shared, WPA-PSK, or WPA2-PSK.
Encryption: If you use WPA-PSK or WPA2-PSK authentication, you
will need to specify whether your wireless network
uses TKIP or AES encryption. If you use Open or Shared
authentication, WEP encryption should be the setting.
Key: If you use WEP, WPA-PSK, or WPA2-PSK authentication,
enter the Key (also known as password) used for your
wireless network.
D-Link DCS-2136L User Manual
34
Section 4: Configuration
Dynamic DNS
DDNS (Dynamic Domain Name Server) will hold a DNS host name and
synchronize the public IP address of the modem when it has been
modified. A user name and password are required when using the DDNS
service. After making any changes, click the Save Settings button to save
your changes.
Enable DDNS: Select this checkbox to enable the DDNS function.
Server Address: Select your Dynamic DNS provider from the pull down
menu or enter the server address manually.
Host Name: Enter the host name of the DDNS server.
User Name: Enter the user name or e-mail used to connect to your
DDNS account.
Password: Enter the password used to connect to your DDNS
server account.
Timeout: Enter the DNS timeout values you wish to use.
Status: Indicates the connection status, which is automatically
determined by the system.
D-Link DCS-2136L User Manual
35
Section 4: Configuration
Image Setup
In this section, you may configure the video image settings for your
camera. A preview of the image will be shown in Live Video.
Enable Privacy The Privacy Mask setting allows you to specify up
Mask: to 3 rectangular areas on the camera's image to be
blocked/excluded from recordings and snapshots.
You may click and drag the mouse cursor over the
camera image to draw a mask area. Right clicking
on the camera image brings up the following menu
options:
Disable All: Disables all mask areas
Enable All: Enables all mask areas
Reset All: Clears all mask areas.
Mirror: This will mirror the image horizontally.
Flip: This will flip the image vertically. When turning Flip on,
you may want to consider turning Mirror on as well.
Power Line: Select the frequency used by your power lines to avoid
interference or distortion.
White Balance: Use the drop-down box to change white balance
settings to help balance colors for different
environments. You can choose from Auto, Outdoor,
Indoor, Fluorescent, and Push Hold.
D-Link DCS-2136L User Manual
36
Section 4: Configuration
Exposure Mode: Changes the exposure mode. Use the drop-down
box to set the camera for Indoor, Outdoor, or Night
environments, or to Moving to capture moving
objects. The Low Noise option will focus on creating a
high-quality picture without noise. You can also create
3 different custom exposure modes. The Max Gain
setting will allow you to control the maximum amount
of gain to apply to brighten the picture.
Denoise: This setting controls the amount of noise reduction
that will be applied to the picture.
Brightness: Adjust this setting to compensate for backlit subjects.
Contrast: Adjust this setting to alter the color intensity/strength.
Saturation: This setting controls the amount of coloration, from
grayscale to fully saturated.
Sharpness: Specify a value from 0 to 8 to specify how much sharpening
to apply to the image.
WDR Level: The WDR function is especially effective in environment
with extreme contrast such as lobby entrances, parking
lots, ATMs, and loading areas. A higher WDR setting will
help in reducing areas with high contrast.
3D filter: Setting this option to Low, Medium, or High will help to
reduce image artifacts, and result in images with less blur
when viewing the camera during the night or in areas
where there are low levels of light.
Reset Default: Click this button to reset the image to factory default
settings.
D-Link DCS-2136L User Manual
37
Section 4: Configuration
Audio and Video
You may configure up to 3 video profiles with different settings for your
camera. Hence, you may set up different profiles for your computer and
mobile display. In addition, you may also configure the two-way audio
settings for your camera. After making any changes, click the Save
Settings button to save your changes.
Number of You can use the drop-down box to set up to 2 active
active profiles: profiles.
Aspect ratio: Set the aspect ratio of the video to 4:3 standard or 16:9
widescreen.
Mode: Set the video codec to be used to JPEG, MPEG-4, or H.264.
Frame size / Frame size determines the total capture resolution,
View window and View window area determines the Live Video
area: viewing window size. If the Frame size is larger than
the Live Video size, you can use the ePTZ controls to
look around.
16:9 1280 x 720, 800 x 450, 640 x 360, 480 x 270, 320
x 176, 176 x 144
4:3 1024 x 768, 800 x 600, 640 x 480, 480 x 360, 320
x 240, 176 x 144
Note: If your View window area is the same as your
Frame size, you will not be able to use the ePTZ
function.
D-Link DCS-2136L User Manual
38
Section 4: Configuration
Maximum frame A higher frame rate provides smoother motion for
rate: videos, and requires more bandwidth. Lower frame
rates will result in stuttering motion, and requires less
bandwidth.
Video Quality: This limits the maximum frame rate, which can be
combined with the "Fixed quality" option to optimize
the bandwidth utilization and video quality. If fixed
bandwidth utilization is desired regardless of the
video quality, choose "Constant bit rate" and select the
desired bandwidth.
Constant bit The bps will affect the bit rate of the video recorded
rate: by the camera. Higher bit rates result in higher video
quality.
Fixed quality: Select the image quality level for the camera to try to
maintain. High quality levels will result in increased bit
rates.
Audio in off: Selecting this checkbox will mute incoming audio.
Audio in gain This setting controls the amount of gain applied to
level: incoming audio to increase its volume.
Audio out off: Selecting this checkbox will mute outgoing audio.
Audio out This setting controls the amount of gain applied to
volume level: outgoing audio to increase its volume.
D-Link DCS-2136L User Manual
39
Section 4: Configuration
Preset
This screen allows you to set preset points for the ePTZ function of the
camera, which allows you to look around the camera's viewable area
by using a zoomed view. Presets allow you to quickly go to and view
a specific part of the area your camera is covering, and you can create
preset sequences, which will automatically change the camera's view
between the different presets according to a defined order and timing
you can set.
Note: If your View window area is the same as your Frame size, you will
not be able to use the ePTZ function.
Video Profile: This selects which video profile to use.
ePTZ Speed: You may select a value between 0 and 64. 0 is the
slowest and 64 is the fastest.
Arrow Buttons Use these buttons to move to a specific part of the
and Home viewing area, which you can then set as a preset. Click
Button: the Home button to return to the center of the viewing
area.
Input Preset Enter the name of the preset you want to create,
Name: then click the Add button to make a new preset. If an
existing preset has been selected from the Preset List,
you can change its name by typing in a new name,
then clicking the Rename button.
Preset List: Click this drop-down box to see a list of all the presets
that have been created. You can select one, then click
the GoTo button to change the displayed camera view
to the preset. Clicking the Remove button will delete
the currently selected preset.
D-Link DCS-2136L User Manual
40
Section 4: Configuration
Preset This section allows you to create a preset sequence,
Sequence: which automatically moves the camera's view between
a set of preset views.
Preset List: To add a preset to the sequence, select it from the
drop-down box at the bottom of this window, set the
Dwell time to determine how long the camera view
will stay at that preset, then click the Add button. The
preset name will appear in the list, followed by the
dwell time to view that preset for.
You can rearrange your presets in the sequence by
selecting a preset in the sequence, then clicking the
arrow buttons to move it higher or lower in the current
sequence.
Clicking the trash can button will remove the currently
selected preset from the sequence.
If you want to change the dwell time for a preset, select
it from the list, enter a new dwell time, then click the
Update button.
D-Link DCS-2136L User Manual
41
Section 4: Configuration
Motion Detection
Enabling Video Motion will allow your camera to use the motion
detection feature. You may draw a finite motion area that will be used for
monitoring. After making any changes, click the Save Settings button to
save your changes.
Enable Video Select this box to enable the motion detection feature
Motion: of your camera.
Sensitivity: Specifies the measurable difference between two
sequential images that would indicate motion. Please
enter a value between 0 and 100.
Percentage: Specifies the amount of motion in the window being
monitored that is required to initiate an alert. If this
is set to 100%, motion is detected within the whole
window will trigger a snapshot.
Draw Motion Draw the motion detection area by dragging your
Area: mouse in the window (indicated by the red square).
Erase Motion To erase a motion detection area, simply click on the red
Area: square that you wish to remove.
Right clicking on the camera image brings up the
following menu options:
Select All: Draws a motion detection area over the
entire screen.
Clear All: Clears any motion detection areas that have
been drawn.
Restore: Restores the previously specified motion
detection areas.
D-Link DCS-2136L User Manual
42
Section 4: Configuration
Time and Date
This section allows you to automatically or manually configure, update,
and maintain the internal system clock for your camera. After making
any changes, click the Save Settings button to save your changes.
Time Zone: Select your time zone from the drop-down menu.
Enable Daylight Select this to enable Daylight Saving Time.
Saving:
Auto Daylight Select this option to allow your camera to configure
Saving: the Daylight Saving settings automatically.
Set Date and Selecting this option allows you to configure the
Time Manually: Daylight Saving date and time manually.
Offset: Sets the amount of time to be added or removed when
Daylight Saving is enabled.
Synchronize Enable this feature to obtain time automatically from
with NTP Server: an NTP server.
NTP Server: Network Time Protocol (NTP) synchronizes the
DCS-2136L with an Internet time server. Choose the
one that is closest to your location.
Set the Date and This option allows you to set the time and date
Time Manually: manually.
Copy Your This will synchronize the time information from your
Computer's PC.
Time Settings:
D-Link DCS-2136L User Manual
43
Section 4: Configuration
Event Setup
In a typical application, when motion is detected, the DCS-2136L sends images to a FTP server or via e-mail as notifications. As shown in the
illustration below, an event can be triggered by many sources, such as motion detection or external digital input devices. When an event is
triggered, a specified action will be performed. You can configure the DCS-2136L to send snapshots or videos to your e-mail address or FTP site.
Action
Event Condition
ex.
Motion detection,
Periodically, Digital input,
System reboot
Media
(what to send)
ex.
Snapshot, Video Clips
Server
(where to send)
ex.
Email, FTP
To start plotting an event, it is suggested to configure server and media columns first so that the DCS-2136L will know what action shall be
performed when a trigger is activated.
D-Link DCS-2136L User Manual
44
Section 4: Configuration
The Event Setup page includes 4 different sections.
• Server
• Media
• Event
• Recording
1. To add a new item - "server, media, or event," click Add. A screen will
appear and allow you to update the fields accordingly.
2. To delete the selected item from the pull-down menu of event, server or
media, click Delete.
3. Click on the item name to pop up a window for modifying.
D-Link DCS-2136L User Manual
45
Section 4: Configuration
Add Server
You can configure up to 5 servers to save snapshots and/or video to. After
making any changes, click the Save Settings button to save your changes.
Server Name: Enter the unique name of your server.
E-mail: Enter the configuration for the target e-mail server
account.
FTP: Enter the configuration for the target FTP server
account.
Network Specify a network storage device. Only one network
Storage: storage device is supported.
SD Card: Use the camera's onboard SD card storage.
D-Link DCS-2136L User Manual
46
Section 4: Configuration
Add Media
There are three types of media, Snapshot, Video Clip, and System Log.
After making any changes, click the Save Settings button to save your
changes.
Media Name: Enter a unique name for media type you want to create.
Snapshot: Select this option to set the media type to snapshots.
Source: Set the video profile to use as the media source. Refer
to Audio and Video on "Audio and Video" on page 38 for
more information on video profiles.
Send pre-event Set the number of pre-event images to take. Preimage(s) [0~4]: event images are images taken before the main event
snapshot is taken.
Send post-event Set the number of post-event images to take. Postimage(s) [0~7]: event images are images taken after the main event
snapshot is taken. You can set up to 7 post-event
images to be taken.
File name prefix: The prefix name will be added on the file name.
Add date and Check it to add timing information as file name suffix.
time suffix to
file name:
D-Link DCS-2136L User Manual
47
Section 4: Configuration
Video clip: Select this option to set the media type to video clips.
Source: Set the video profile to use as the media source. Refer
to "Audio and Video" on page 51 for more information
on video profiles.
Pre-event This sets how many seconds to record before the main
recording: event video clip starts. You can record up to 4 seconds
of pre-event video.
Maximum Set the maximum length of video to record for your
duration: video clips.
Maximum file Set the maximum file size to record for your video clips.
size:
File name prefix: This is the prefix that will be added to the filename of
saved video clips.
System log: Select this option to set the media type to system logs.
This will save the event to the camera system log, but
will not record any snapshots or video.
D-Link DCS-2136L User Manual
48
Section 4: Configuration
Add Event
Create and schedule up to 2 events with their own settings here. After
making any changes, click the Save Settings button to save your
changes.
Event name: Enter a name for the event.
Enable this Select this box to activate this event.
event:
Priority: Set the priority for this event. The event with higher
priority will be executed first.
Delay: Select the delay time before checking the next event. It
is being used for both events of motion detection and
digital input trigger.
Trigger: Specify the input type that triggers the event.
Video Motion Motion is detected during live video monitoring. Select
Detection: the windows that need to be monitored.
Periodic: The event is triggered in specified intervals. The trigger
interval unit is in minutes.
Digital input: The external trigger input to the camera.
System Boot: Triggers an event when the system boots up.
Network Lost: Triggers an event when the network connection is lost.
Passive Infrared Triggers an event when the PIR sensor is activated by
Sensor: moving infrared objects even in dark environment.
D-Link DCS-2136L User Manual
49
Section 4: Configuration
Time: Select Always or enter the time interval.
Trigger D/O: Select to trigger the digital output for a specific number
of seconds when an event occurs.
Trigger white Select to trigger the white light LED only during an
light LED event or for a specific duration of time when an event
occurs.
D-Link DCS-2136L User Manual
50
Section 4: Configuration
Add Recording
Here you can configure and schedule the recording settings. After
making any changes, click the Save Settings button to save your
changes.
Recording entry The unique name of the entry.
name:
Enable this Select this to enable the recording function.
recording:
Priority: Set the priority for this entry. The entry with a higher
priority value will be executed first.
Source: The source of the stream.
Recording Scheduling the recording entry.
schedule:
Recording Configuring the setting for the recording.
settings:
Destination: Select the folder where the recording file will be stored.
Total cycling Input a value between 1MB and 2TB for recording
recording size: space. New recordings will replace the oldest recording
when the total recording size exceeds this value.
Size of each file If this is selected, files will be separated based on the
for recording: file size you specify.
Time of each file If this is selected, files will be separated based on the
for recording: maximum length you specify.
File Name Prefix: The prefix name will be added on the file name of the
recording file(s).
D-Link DCS-2136L User Manual
51
Section 4: Configuration
SD Card
Here you may browse and manage the recorded files which are stored on
the SD card.
Format SD Card: Click this icon to automatically format the SD card and
create "picture" & "video" folders.
View Recorded If the picture files are stored on the SD card, click on the
Picture: picture folder and choose the picture file you would
like to view.
Playback If video files are stored on the SD card, click on the
Recorded Video: video folder and choose the video file you would like
to view.
Refresh: Reloads the file and folder information from the SD
card.
D-Link DCS-2136L User Manual
52
Section 4: Configuration
Advanced
Digital Input/Output
This screen allows you to control the behavior of digital input and digital
output devices. The I/O connector provides the physical interface for
digital output (DO) and digital input (DI) that is used for connecting a
variety of external alarm devices such as IR-Sensors and alarm relays.
The digital input is used for connecting external alarm devices and once
triggered images will be taken and e-mailed. After making any changes,
click the Save Settings button to save your changes.
Select D/I or The camera will send a signal when an event is triggered,
D/O Mode: depending upon the type of device connected to the DI
circuit.
N.C. stands for Normally Closed. This means that the
normal state of the circuit is closed. Therefore events
are triggered when the device status changes to "Open."
N.O. stands for Normally Open. This means that the
normal state of the circuit is open. Therefore events are
triggered when the device status changes to "Closed."
D-Link DCS-2136L User Manual
53
Section 4: Configuration
White LED Light
Here you can configure the white light LED settings. The settings on this
page will control how the light button on the live view page will appear.
It will also set up how the white light LED functions when used with event
triggers.
Light: The camera can enable or disable the white LED light
according to your preferences. This setting provides
additional controls depending on your selection. The options
are None, Pulse, Active, and Slider.
None: If the white light LED option is set to none, the camera PIR
sensor or any other external triggers will not activate the
white light LED.
Pulse: Select Pulse to activate the built-in light for a defined period
of time, for example 20 seconds. You can set how the white
light functions by selecting an action for when the white
light LED becomes active and goes inactive.
Active: Select Active to have the white light LED activated on a
predefined event, or by enabling via button on the live view
page. You can set how the white light functions by selecting
an action for when the white light LED becomes active and
goes inactive.
Slider: Selecting this option will enable a slider on the live view
page. The slider will allow you to control the brightness of
the built-in light, sliding it left to dim and sliding it right to
brighten.
Auto: Selecting this option will enable the white LED to
automatically come on when it senses a the surrounding
light levels have reached a certain threshold.
D-Link DCS-2136L User Manual
54
Section 4: Configuration
HTTPS
This page allows you to install and activate an HTTPS certificate for secure
access to your camera. After making any changes, click the Save Settings
button to save your changes.
Enable Enable the HTTPS service.
HTTPS Secure
Connection:
Create Choose the way the certificate should be created.
Certificate Three options are available:
Method:
Create a self-signed certificate automatically
Create a self-signed certificate manually
Create a certificate request and install
Status: Displays the status of the certificate.
Note: The certificate cannot be removed while the HTTPS is
still enabled. To remove the certificate, you must first
uncheck Enable HTTPS secure connection.
D-Link DCS-2136L User Manual
55
Section 4: Configuration
Access List
Here you can set access permissions for users to view your DCS-2136L.
Allow list: The list of IP addresses that have the access right to the
camera.
Start IP address: The starting IP Address of the devices (such as a computer)
that have permission to access the video of the camera.
Click Add to save the changes made.
Note: A total of seven lists can be configured for both
columns.
End IP address: The ending IP Address of the devices (such as a
computer) that have permission to access the video of
the camera.
Delete allow list: Remove the customized setting from the Allow List.
Deny list: The list of IP addresses that have no access rights to
the camera.
Delete deny list: Remove the customized setting from the Delete List.
For example:
When the range of the Allowed List is set from 1.1.1.0
to 192.255.255.255 and the range of the Denied List is
set from 1.1.1.0 to 170.255.255.255. Only users with IPs
located between 171.0.0.0 and 192.255.255.255 can
access the DCS-2136L.
D-Link DCS-2136L User Manual
Alowed
List
Denied
List
56
Section 4: Configuration
Maintenance
Device Management
You may modify the name and administrator’s password of your camera,
as well as add and manage the user accounts for accessing the camera.
You may also use this section to create a unique name and configure the
OSD settings for your camera.
Admin Password Set a new password for the administrator’s account.
Setting:
Add User Account: Add new user account.
User Name: The user name for the new account.
Password: The password for the new account.
User List: All the existing user accounts will be displayed here.
Camera Name: Create a unique name for your camera that will be
added to the file name prefix when creating a snapshot
or a video clip.
Enable OSD: Select this option to enable the On-Screen Display
feature for your camera.
Label: Enter a label for the camera, which will be shown on
the OSD when it is enabled.
Show Time: Select this option to enable the time-stamp display on
the video screen.
LED: You may specify whether or not to illuminate the status
LED on the camera.
D-Link DCS-2136L User Manual
57
Section 4: Configuration
System
In this section, you may backup, restore and reset the camera
configuration, or reboot the camera.
Save To Local You may save your current camera configuration as a
Hard Drive: file on your computer.
Load From Local Locate a pre-saved configuration by clicking Browse
Hard Drive: and then restore the pre-defined settings to your
camera by clicking Load Configuration.
Restore to You may reset your camera and restore the factory
Factory Defaults: settings by clicking Restore Factory Defaults.
Reboot Device: This will restart your camera.
D-Link DCS-2136L User Manual
58
Section 4: Configuration
Firmware Upgrade
The camera's current firmware version will be displayed on this screen.
You may visit the D-Link Support Website to check for the latest available
firmware version.
To upgrade the firmware on your DCS-2136L, please download and save
the latest firmware version from the D-Link Support Page to your local
hard drive. Locate the file on your local hard drive by clicking the Browse
button. Select the file and click the Upload button to start upgrading the
firmware.
Current Displays the detected firmware version.
Firmware
Version:
Current Product Displays the camera model name.
Name:
File Path: Locate the file (upgraded firmware) on your hard drive
by clicking Browse.
Upload: Uploads the new firmware to your camera.
D-Link DCS-2136L User Manual
59
Section 4: Configuration
Status
Device Info
This page displays detailed information about your device and network
connection.
D-Link DCS-2136L User Manual
60
Section 4: Configuration
Logs
This page displays the log information of your camera. You may download
the information by clicking Download. You may also click Clear to delete
the saved log information.
D-Link DCS-2136L User Manual
61
Section 4: Configuration
Help
This page provides helpful information regarding camera operation.
D-Link DCS-2136L User Manual
62
Appendix A: DI/DO Specifications
DI/DO Specifications
Pin 1
Pin 2
Pin 3
Pin 4
PIN
NOTE
FUNCTION
1
Digital Out (DO)
Uses an open-drain NFET transistor with the source connected to GND in camera. If used
with an external relay, a diode must be connected in parallel with the load for protection
against voltage transients. Max loading is 100 mA.
2
Digital In (DI)
A switch from DI to DC 5 V, activated by setting NO. or NC.
3
DC5V OUTPUT
DC 5 V Output / Max. 100 mA
4
GND
GND
Internal 5V Power
External 3~12V Power
DND
DND
DC Power 5V
DC Power 5V
5V
DI
N.C / N.O
5V
DI
N.C / N.O
Reed switch
DC Power 3V~12V
Reed switch
R
R
DO
100 mA
DO
Diode
ALARM
D-Link DCS-2136L User Manual
100 mA
Diode
ALARM
63
Appendix B: Technical Specifications
Technical Specifications
Camera
Network
Camera Hardware
Profile
ƒƒ 1/3” Megapixel progressive CMOS sensor
ƒƒ 5 meter white light illumination distance
ƒƒ Minimum illumination: 0 lux with white light LED on
ƒƒ Built-in PIR sensor (5 meter)
ƒƒ Built-in microphone and speaker
ƒƒ 10x digital zoom
Image Features
ƒƒ Configurable image size, quality, frame rate, and bit rate
ƒƒ Time stamp and text overlays
ƒƒ Configurable motion detection windows
ƒƒ Configurable privacy mask zones
ƒƒ Configurable shutter speed, brightness, saturation, contrast,
sharpness, and WDR
Video Compression
ƒƒ Simultaneous H.264/MPEG-4/MJPEG format compression
ƒƒ H.264/MPEG-4 multicast streaming
ƒƒ JPEG for still images
Video Resolution
16:9 - 1280 x 720, 800 x 450, 640 x 360, 480 x 270, 320 x 176,
176 x 144 up to 30 fps recording
4:3 - 1024 x 768, 800 x 600, 640 x 480, 480 x 360, 320 x 240,
176 x 144 up to 30 fps recording
Audio Support
ƒƒ G.726
ƒƒ G.711
External Device
Interface
ƒƒ 10/100 BASE-TX Fast Ethernet port
ƒƒ IEEE 802.11ac 2.4GHz, 5GHz Dual-Band Wireless
ƒƒ DI/DO port
ƒƒ MicroSD/SDHC card slot
Network Protocols
ƒƒ IPv6
ƒƒ IPv4
ƒƒ TCP/IP
ƒƒ UDP
ƒƒ ICMP
ƒƒ DHCP client
ƒƒ NTP client (D-Link)
ƒƒ DNS client
ƒƒ DDNS client (D-Link)
ƒƒ SMTP client
ƒƒ FTP client
ƒƒ HTTP / HTTPS
ƒƒ Samba client
ƒƒ PPPoE
ƒƒ UPnP port forwarding
ƒƒ RTP / RTSP/ RTCP
ƒƒ IP filtering
ƒƒ QoS
ƒƒ CoS
ƒƒ Multicast
ƒƒ IGMP
ƒƒ SNMP
ƒƒ ONVIF compliant
Security
ƒƒ Administrator and user group protection
ƒƒ Password authentication
ƒƒ HTTP and RTSP digest encryption
D-Link DCS-2136L User Manual
ƒƒ Focal length: 3.6 mm
ƒƒ Aperture: F1.4
ƒƒ Angle of view:
ƒƒ (H) 64°
ƒƒ (V) 46.5°
ƒƒ (D) 92.4°
64
Appendix B: Technical Specifications
System
System
Management Requirements for
Web Interface
General
ƒƒ Operating System: Microsoft Windows 7/Vista/XP/2000
ƒƒ Browser: Internet Explorer, Firefox, Netscape, Opera
Event Management
ƒƒ Motion detection
ƒƒ Event notification and uploading of snapshots/video clips via
e-mail or FTP
ƒƒ Supports multiple SMTP and FTP servers
ƒƒ Multiple event notifications
ƒƒ Multiple recording methods for easy backup
Remote
Management
ƒƒ Take snapshots/video clips and save to local hard drive or NAS
via web browser
ƒƒ Configuration interface accessible via web browser
Mobile Support
Windows 7/Vista/XP system, Pocket PC, or mobile phone
mydlink mobile app for iOS and Android mobile devices
D-ViewCam™ System ƒƒ Operating System: Microsoft Windows 7/Vista/XP
Requirements
ƒƒ Web Browser: Internet Explorer 7 or higher
ƒƒ Protocol: Standard TCP/IP
D-ViewCam™
Software Functions
ƒƒ Remote management/control of up to 32 cameras
ƒƒ Viewing of up to 32 cameras on one screen
ƒƒ Supports all management functions provided in web interface
ƒƒ Scheduled motion triggered, or manual recording options
Weight
ƒƒ Device: 84.0g (without stand)
ƒƒ Stand: 45.0g
External Power
Adaptor
ƒƒ Input: 100 to 240 V AC, 50/60 Hz
ƒƒ Output: 5 V DC, 1.2 A, 50/60 Hz
Power Consumption ƒƒ 4 watts
Temperature
ƒƒ Operating: 0 to 40 °C (32 to 104 °F)
ƒƒ Storage: -20 to 70 °C (-4 to 158 °F)
Humidity
ƒƒ Operating: 20% to 80% non-condensing
ƒƒ Storage: 5% to 95% non-condensing
Certifications
ƒƒ CE
ƒƒ CE LVD
ƒƒ FCC
ƒƒ C-Tick
D-Link DCS-2136L User Manual
65
Appendix B: Technical Specifications
Dimensions
•
D-Link DCS-2136L User Manual
66
Appendix C: Safety Statements
Safety Statements
CE Mark Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take
adequate measures.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
D-Link DCS-2136L User Manual
67
Appendix C: Safety Statements
IMPORTANT NOTICE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory
to match the intended destination. The firmware setting is not accessible by the end user.
For detailed warranty information applicable to products purchased outside the United States, please contact the corresponding local D-Link
office.
Industry Canada Notice:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.
This device has been designed to operate with an antenna having a maximum gain of 2 dB. Antenna having a higher gain is strictly prohibited per
regulations of Industry Canada. The required antenna impedance is 50 ohms.
D-Link DCS-2136L User Manual
68