Sharp 21SFX10L Service manual

21G-FX10L(A)
SERVICE MANUAL
S61015821GFX10L(A)
COLOUR TELEVISION
Chassis No. GA-8P (VE)
MODEL
21G-FX10L(A)
In the interests of user safety (Required by safety regulations in some countries) the set should be restored to its original
condition and only parts indentical to those specified should be used.
CONTENTS
Page
IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................................... 1-1
LOCATION OF USER’S CONTROL ...................................................................................................................... 2-1
INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................................. 3-1
SERVICE MODE ..................................................................................................................................................... 4-1
ADJUSTMENT METHOD ........................................................................................................................................ 5-1
WAVEFORMS ......................................................................................................................................................... 6-1
CHASSIS LAYOUT ................................................................................................................................................. 7-1
BLOCK DIAGRAM .................................................................................................................................................. 8-1
DESCRIPTION OF SCHEMATIC DIAGRAM .......................................................................................................... 9-1
SCHEMATIC DIAGRAMS ......................................................................................................................................10-1
PRINTED WIRING BOARD ASSEMBLIES ........................................................................................................... 11-1
Parts Guide
ELECTRICAL SPECIFICATIONS
POWER INPUT.......................... AC 110-220 V, 50/60 Hz
POWER RATING .................................................... 78W
PICTURE SIZE ............................ 1,239 cm2 (192sq inch)
CONVERGENCE ............................................. Magnetic
SWEEP DEFLECTION .................................... Magnetic
FOCUS ......................................................... Electrostatic
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ...................... 45.75 MHz
Sound IF Carrier Frequency ...................... 41.25 MHz
Color Sub-Carrier Frequency ......................42.17 MHz
(Nominal)
AUDIO POWER
OUTPUT RATING......................... 3.0 W (RMS) x 2pcs
SPEAKER
SIZE ........................................................ 9 x 5cm, 2pcs
VOICE COIL IMPEDANCE .................16 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF ........................................75 ohm Unbalanced
TUNING RANGES
VHF-Channels ................................................. 2 thru 13
UHF-Channels ................................................14 thru 69
CATV Channels ............................................. 1 thru 125
(EIA, Channel Plan U.S.A.)
Specifications are subject to change without
prior notice.
This document has been published to be used for after sales service only.
The contents are subject to change without notice.
SHARP CORPORATION
21G-FX10L(A)
CHAPTER 1. IMPORTANT SERVICE SAFETY PRECAUTION
Service Manual
TV
E
Market
21G-FX10L(A)
IMPORTANT SERVICE SAFETY PRECAUTION
Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
X-RADIATION AND HIGH VOLTAGE LIMITS
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock
hazards when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation.
The only potential source of X-ray in current solid
state TV receivers is the picture tube. However, the
picture tube does not emit measurable X-Ray
radiation, if the high voltage is as specified in the
"High Voltage Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem.
Every time a color chassis is serviced, the brightness
should be tested while monitoring the high voltage
with a meter to be certain that the high voltage does
not exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified
or make unrecommended circuit modifications to the
high voltage circuitry.
6. W h e n t r o u b l e s h o o t i n g a n d t a k i n g t e s t
measurements on a receiver with excessive high
voltage, avoid being unnecessarily close to the
receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
1–1
21G-FX10L(A)
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 110~220 volt AC
outlet, (Do not use an isolation transformer for this
test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15μF capacitor in series
with all exposed metal cabinet parts and a known
earth ground, such as electrical conduit or electrical
ground connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
DVM
AC SCALE
1.5k ohm
10W
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
SAFETY NOTICE
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by " "
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
1–2
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
21G-FX10L(A)
CHAPTER 2. LOCATION OF USER'S CONTROL
Service Manual
TV
E
Market
21G-FX10L(A)
[1] LOCATION OF USER'S CONTROL
AV
AV
AVa
2–1
21G-FX10L(A)
CHAPTER 3. INSTALLATION AND SERVICE INSTRUCTIONS
Service Manual
TV
E
Market
21G-FX10L(A)
INSTALLATION AND SERVICE INSTRUCTIONS
Note:
(1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
HIGH VOLTAGE CHECK
The receiver is protected by a 3.15A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
X-RADIATION PROTECTOR CIRCUIT TEST
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 110~220V AC using a variac transformer for
accurate input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to C602 +ve and make
sure that the voltmeter reads 20 ±1.1V.
5. Apply external 28.5V DC at C602 +ve by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and make
a short circuit between C602 -ve and C602 +ve.
Now make sure that normal picture appears on the
screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
3–1
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 110~220V
AC line voltage, with a strong air signal or a properly
tuned in test signal.
3. Enter the service mode and set Y-mute ON by using
Service R/C.
4. The voltage should be approximately 23kV (at zero
beam).
If a correct reading cannot be obtained, check circuitry
for malfunctioning components. After the voltage test,
make Y-mute off to the normal mode.
21G-FX10L(A)
CHAPTER 4. SERVICE MODE
Service Manual
TV
E
Market
21G-FX10L(A)
SERVICE MODE
1. Service mode is switched by SERVICE key, CH UP + VOL DOWN when reset.
2. Service mode is cancelled by SERVICE key during Service mode.
3. Service mode can be switched to the following 5 modes via MENU key:
First mode of service when entering by
SERVICE key.
Adjustment mode
Setting mode
First mode of service when entering by
2 local keys.
Confirmation mode
Option mode
NVM Edit mode
4䋮During Service mode, AFT operation is prohibited. The setting data for PLL is always set to fo data.
5䋮During Service mode, the following user data are set to default value and stored as last memory.
PICTURE䋯TINT䋯COLOR䋯BRIGHT䋯SHARP䋯COLOR TEMP.
BASS䋯TREBLE䋯BALANCE䋯MTS䋯FAO䋯SPEAKER䋯ENERGY SAVE
6䋮During Service mode, OSD display for ON/OFF is toggled via [CH CALL] key.
䊶At display OFF condition, if changing adjustment data, channel, input source, it remains display OFF.
䊶At display OFF condition, if changing adjustment item, it returns to display ON.
7䋮During Service mode, the following operation are prohibited.
CLOSED CAPTION䋯No signal BLUE SCREEN
8䋮During Service mode, sound is muted(only MTSIC) except when selecting the following items.
V24, M01
4–1
21G-FX10L(A)
AUTO ADJUSTMENT
H-VCO
1. When there is H-VCO auto adjustment key input at item H-VCO, auto adjustment will be implemented.
2. H-FREE (1chip) is set to 1.
3. H-OUT (1chip) is set by intelligent monitor output.
4. IM input becomes TIM input.
5. H-VCO (1chip) data is changed so that the number is 126 inside 8ms interval.
6. When adjustment is completed, OSD display and H-VCO auto adjustment data of EERPOM are updated.
7. H-FREE (1chip), intelligent monitor output, IM input mode are recovered.
RF-AGC
1. If there is RF-AGC auto adjustment key input at item RF-AGC, auto adjustment will be implemented.
2. AGC-OUT (MONITOR(1chip)is set by intelligent monitor output.
3. IM input becomes AD input.
4. RF-AGC(1chip) is decreased from current RF-AGC value to 0, the maximum AFT input voltage is obtained.
5. RF-AGC(1chip) is increased until at the point of AFT input voltage is (max. 0.3V), adjustment is completed.
6. When adjustment is completed, OSD display and RFGC auto adjustment status in EEPROM are updated.
7. Intelligent monitor output, IM input mode are recovered.
PIF-VCO
1. If there is PIF-VCO auto adjustment key input at item PIF- VCO, auto adjustment will be implemented.
2. VIF-DEF (1chip) is set to 1.
3. AFT output (1chip) is set by intelligent monitor output.
4. IM input becomes AD input.
5. VIF-VCO (1chip) is changed so the input voltage becomes 2.5V.
6. When adjustment is completed, OSD display and PIF-VCO auto adjustment status in EEPROM are updated.
7. VIF-DEF (1chip) intelligent monitor output, IM input mode are recovered.
S-TRAP
1. If there is S-TRAP auto adjustment key input at item S-TRAP, auto adjustment will be implemented.
2. S-TRAP OUTPUT is set by intelligent monitor output.
3. IM input becomes AD input.
4. S-Trap (1chip) is set to the value of V45(S-TRAP ADJ Start).
5. S_Trap_Result is set to the value of V45(S-TRAP ADJ Start).
6. S-Trap (1chip) is increased until the minimum input voltage becomes minimum.
7. Wait 20ms before sampling the new_ AD_data.
8. When adjustment is completed, OSD display and S-TRAP auto adjustment status in EEPROM are updated.
9. S-TRAP (1chip) intelligent monitor output, IM input mode are recovered.
4–2
21G-FX10L(A)
CHAPTER 5. ADJUSTMENT METHOD
Service Manual
TV
E
Market
21G-FX10L(A)
Memory Map Data
Caution: To get into the service mode, one of the ways is press direct key for service items.
There is three stage of Service Mode data
First stage data from V01 ~ M01
to go into second stage of service mode data, press MENU key
Second stage data from F01 ~ F160
to go into third stage of service mode data, press MENU key
Third stage data from O01 ~ O31
Adjustmet Mode (First Stage)
V25
V26
DATA
LENGTH
0~127
0~127
0~127
0~255
0~63
0~63
0~7
0~31
0~127
0~63
-7~+7
-15~+15
-31~+31
0~63
0~255
0~255
0~255
0~127
0~127
0~127
0~127
0~255
0~2
0~127 (O20=0)
0~255 (O20=1)
0~7
0~127
INITIAL
DATA
127
64
64
128
41
41
4
16
127
32
0
0
0
32
127
127
127
64
64
64
64
32
0
127
255
4
64
VS-CORRECT
V27
0~63
36
VS-CORRECT50
V28
-13~+13
0
0
FIX
V LINEARITY
V29
0~63
35
36
*FIX
V LINEARITY50
PARABOLA
PARABOLA50
TRAPEZIUM
TRAPEZIUM50
H-SIZE
H-SIZE50
UPPER CORNER
UPPER CORNER50
LOWER CORNER
LOWER CORNER50
ANGLE ADJ
ANGLE ADJ50
BOW ADJ
BOW ADJ50
S-TRAP ADJ START
S-TRAP STOP
MTS-ATT
V30
V31
V32
V33
V34
V35
V36
V37
V38
V39
V40
V41
V42
V43
V44
V45
V46
M01
-13~+13
0~63
-13~+13
0~63
-13~+13
0~63
-13~+13
0~63
-13~+13
0~63
-13~+13
0~63
-13~+13
0~63
-13~+13
0~127
0~127
0~15
0
32
0
32
0
32
0
32
0
32
0
31
0
31
0
25
95
10
0
32
0
32
0
32
0
32
0
32
0
31
0
31
0
25
95
10
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
EEPROM ITEMS
OSD
SUB-CON
SUB-TINT
SUB-COL
SUB-BRI
SUB-SHP-PRE
SUB-SHP-OVER
V-SHIFT
H-SHIFT
RF-AGC
V-SIZE
V-SHIFT50
H-SHIFT50
V-SIZE50
VIF-VCO
R-CUT
G-CUT
B-CUT
R-DRI
B-DRI
SUB-COLOR-YUV
SUB-TINT-YUV
CC-POS
SCREEN CUT OFF
V01
V02
V03
V04
V05
V06
V07
V08
V09
V10
V11
V12
V13
V14
V15
V16
V17
V18
V19
V20
V21
V22
V23
SUB-VOL
V24
H-VCO
S-TRAP
Auto Adjustment Item
ķ H-VCO , ĸ RF-AGC, Ĺ VIF-VCO, ĺ S-TRAP
Remark: * Initial Data different with Setting Data
5–1
SETTING DATA
FIX/ADJ/AUTO
127
64
64
128
44
24
4
16
127
32
0
0
0
32
127
127
127
64
64
64
64
32
0
115
4
64
ADJ
ADJ
ADJ
ADJ
*FIX
*FIX
ADJ
ADJ
AUTO
ADJ
FIX
FIX
FIX
AUTO
ADJ
ADJ
ADJ
ADJ
ADJ
FIX
FIX
ADJ
FIX
30
*FIX
REMARK
*FIX
AUTO
AUTO
ADJUST IF NECESSARY TO
IMPROVE
ADJUST IF NECESSARY TO
IMPROVE
21G-FX10L(A)
SETTING MODE (Second Stage)
EEPROM ITEMS
OSD
ABCL-Gain
SHP-AV-PRE
SHP-YUV-PRE
SHP-P-PRE
SHP-N3-PRE
SHP-AV-OVER
SHP-YUV-OVER
SHP-P-OVER
SHP-N3-OVER
SHP ANT-ON II OFFSET
RGB-CLIP
E-SAVE
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
FAO-VOL
F13
VIF-G
YDL-TV
YDL-TV-P
YDL-TV-N3
YDL-AV
YDL-AV-P
YDL-AV-N3
YDL-YUV
TINT-AV
COL-AV
COL-P
COL-N3
R-R
R-B
B-R
B-B
GAMMA
BS-D
BS-C
SL-TV
SL-AV
SL-YUV
AFC2
VD-TV
VD-AV
VD-YUV
AS-TV
AS-AV
AS-YUV
FBP-TV
FBP-AV
FBP-YUV
C.Clip Level
CP
CC LEVEL
OSD POS-H
OSD POS-V50
OSD POS-V60
OFFSET-ADJ-COLOR
OFFSET-ADJ-TINT
WAITガMDガTIMER
R-CUT-YUV
G-CUT-YUV
B-CUT-YUV
R-DRI-YUV
B-DRI-YUV
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F41
F42
F43
F44
F45
F46
F47
F48
F49
F50
F51
F52
F53
F54
F55
F56
F57
F58
F59
DATA
LENGTH
0/1
-16~+16
-16~+16
-31~+31
-31~+31
-16~+16
-16~+16
-31~+31
-31~+31
-15~0
0/1
0~63
0~127 (O20=0)
0~255 (O20=1)
0~7
0~7
0~7
0~7
0~7
0~7
0~7
0~7
-32~+32
-32~+32
-31~+31
-31~+31
-32~+32
-32~+32
-32~+32
-32~+32
0~3
0~3
0~3
0~7
0~7
0~7
0~3
0~7
0~7
0~7
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0~31
0~31
1~55
1~50
-32~+32
-32~+32
0/1
-63~+63
-63~+63
-63~+63
-63~+63
-63~+63
Remark: * Initial Data different with Setting Data
5–2
INITIAL
DATA
0
0
0
0
0
0
0
0
0
-10
0
30
120
246
5
5
5
5
5
5
5
0
+6
0
+24
0
+3
-2
-8
+6
1
0
0
2
2
0
0
5
7
1
1
1
0
0
0
0
0
1
0
0
38
23
+10
+2
1
0
0
0
0
0
SETTING DATA FIX/ADJ/AUTO
0
-5
0
0
0
-5
0
0
0
-10
0
30
81
7
5
5
5
5
5
4
0
-8
+10
+24
0
+7
0
-20
+9
3
0
0
1
2
0
1
1
2
0
1
1
0
0
0
0
0
1
0
10
48
37
+17
+8
1
0
0
0
0
0
FIX
*FIX
FIX
FIX
FIX
*FIX
FIX
FIX
FIX
FIX
FIX
FIX
*FIX
*FIX
FIX
FIX
FIX
FIX
FIX
*FIX
FIX
*FIX
*FIX
FIX
FIX
*FIX
*FIX
*FIX
*FIX
*FIX
FIX
FIX
*FIX
FIX
FIX
*FIX
*FIX
*FIX
*FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
*FIX
*FIX
*FIX
*FIX
*FIX
FIX
FIX
FIX
FIX
FIX
FIX
21G-FX10L(A)
SETTING MODE (Second Stage)
EEPROM ITEMS
OSD
CONTRAST OFFSET
CONTRAST YUV OFFSET
BRIGHT OFFSET
BRIGHT AV2 OFFSET
BRIGHT YUV OFFSET
TRAP
TRAP-P
TRAP-N3
AFC1-Gain-TV
AFC1-Gain-AV
AFC1-Gain-YUV
OM-DET
˞˯ˉˣ˽̅̊
C-ANGLE
˲ˉˠ˨
˱ˉˠ˨
AS-SPEED-DN
AS-SPEED-UP
CR-PEDESTEL-ADJ
CB-PEDESTEL-ADJ
SIF-BPF-WIDE
SIF-BPF-WIDE-LOW
SIF-BPF-WIDE-HIGH
F60
F61
F62
F63
F64
F65
F66
F67
F68
F69
F70
F71
F72
F73
F74
F75
F76
F77
F78
F79
F80
F81
F82
COL-SYSTEM
F83
Pow-Storage
SIF45 GAIN DOWN
S-TRAP OFF
BASS OFFSET
MID1 OFFSET
MID2 OFFSET
MID3 OFFSET
TREBLE OFFSET
AVL LEVEL
F84
F85
F86
F87
F88
F89
F90
F91
F92
AVL OPTION
F93
AU-ATT AMP
F94
OSD LEVEL
F95
R MTX UP
MATRIX ADJ
SAP LEVEL
STEREO SENS
SAP SENS
MER
MEL1
MEL2
MEL3
MEL4
MEL5
MEL6
S-St-Point
F96
F97
F98
F99
F100
F101
F102
F103
F104
F105
F106
F107
F108
DATA
LENGTH
-63~+63
-63~+63
-63~+63
-15~+15
-63~+63
0~3
0~3
0~3
0~3
0~3
0~3
0/1
0~2
0/1
0~3
0~3
0/1
0/1
0~15
0~15
0~7
0/1
0/1
0: 11XX (AUTO)
1: 0011 (PAL-M)
2: 0111 (PAL-N)
3: 0110 (N358)
4: 10XX (AUTO1)
0/1
0/1
0/1
-4~+4
-4~+4
-4~+4
-4~+4
-4~+4
0~3
0: fix to 0
1: fix to 1
2: AVL in
SOUND MENU
0 (0dB)/1(3dB)
0: 10%
1: 30%
2: 50%
3: 70%
4: 90%
0/1
0~3
0/1
0/1
0/1
0~255
0~255
0~255
0~255
0~255
0~255
0~255
0~60
Remark: * Initial Data different with Setting Data
5–3
INITIAL
DATA
0
0
0
+1
0
2
2
2
0
3
3
0
0
0
0
0
0
0
8
8
3
0
0
SETTING DATA FIX/ADJ/AUTO
0
0
-25
+4
0
0
2
2
0
3
3
0
0
0
0
0
0
0
8
8
1
0
0
FIX
FIX
*FIX
*FIX
FIX
*FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
*FIX
FIX
FIX
3
3
FIX
1
0
1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
1
FIX
FIX
*FIX
FIX
FIX
FIX
FIX
FIX
*FIX
2
1
*FIX
0
1
*FIX
3
3
FIX
0
0
0
0
0
70
150
156
163
165
170
180
21
0
0
0
0
0
70
150
156
163
165
170
180
21
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
21G-FX10L(A)
SETTING MODE (Second Stage)
EEPROM ITEMS
OSD
S-Sp-Point
S-Step
CONT NEWS
CONT MUSIC
CONT MOVIE
BRIGHT NEWS
BRIGHT MUSIC
BRIGHT MOVIE
COL NEWS
COL MUSIC
COL MOVIE
SHARP NEWS
SHARP MUSIC
SHARP MOVIE
SURR NEWS
SURR MUSIC
SURR MOVIE
TREBLE NEWS
TREBLE MUSIC
TREBLE MOVIE
BASS NEWS
BASS MUSIC
BASS MOVIE
EQ BASS NEWS
EQ BASS MUSIC
EQ BASS MOVIE
EQ MID1 NEWS
EQ MID1 MUSIC
EQ MID1 MOVIE
EQ MID2 NEWS
EQ MID2 MUSIC
EQ MID2 MOVIE
EQ MID3 NEWS
EQ MID3 MUSIC
EQ MID3 MOVIE
EQ TRE NEWS
EQ TRE MUSIC
EQ TRE MOVIE
S-BOOST NEWS
S-BOOST MUSIC
S-BOOST MOVIE
CORNER UP-LOW EN
BOW/ANGLE-ON/OFF
SHP-NR-OFFSET
V-FREE60
TAKEOFF TV
STRAP OFFSET
RGB MUTE TIME
H-BLK LEFT
H-BLK RIGHT
F109
F110
F111
F112
F113
F114
F115
F116
F117
F118
F119
F120
F121
F122
F123
F124
F125
F126
F127
F128
F129
F130
F131
F132
F133
F134
F135
F136
F137
F138
F139
F140
F141
F142
F143
F144
F145
F146
F147
F148
F149
F150
F151
F152
F153
F154
F155
F156
F157
F158
H-STOP DELAY
F159
SYS MUTE
F160
DATA
LENGTH
0~60
0~60
0~60
0~60
0~60
-30~+30
-30~+30
-30~+30
-30~+30
-30~+30
-30~+30
-30~+30
-30~+30
-30~+30
0(OFF)/1(ON)
0(OFF)/1(ON)
0(OFF)/1(ON)
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
-10~+10
0(OFF)/1(ON)
0(OFF)/1(ON)
0(OFF)/1(ON)
0/1
0(OFF)/1(ON)
-15~0
0/1
0/1
-16~+16
0~8
0~7
0~7
0: 5ms
1: 10ms
2: 15ms
3: 20ms
0/1
Remark: * Initial Data different with Setting Data
5–4
INITIAL
DATA
60
7
40
50
60
0
0
0
0
0
+10
-10
0
+5
0
0
0
-10
0
+5
-5
0
+10
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
1
0
0
0
0
0
SETTING DATA FIX/ADJ/AUTO
60
7
40
50
60
0
0
0
0
0
+10
-10
0
+5
0
0
0
-10
0
+5
-5
0
+10
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
0
1
0
0
1
0
3
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
*FIX
FIX
*FIX
1
1
FIX
0
0
FIX
21G-FX10L(A)
Setting Mode (Third stage)
Data
O01
O02
O03
O04
O05
O06
O07
O08
O09
O10
O11
O12
O13
O14
O15
O16
O17
O18
O19
O20
O21
O22
O23
O24
O25
O26
O27
O28
O29
O30
O31
OPTION FUNCTION
Description
0 : ALPS
1 : MATSUSHITA
FAO
DIS/ENA
* PON-CH
DIS/ENA
ANTENNA BOOSTER DIS/ENA
AV
DIS/ENA
0 : AV1
AV2
1 : AV2
MTS
DIS/ENA
0 : without COMPONENT
COMPONENT
1 : COMPONENT (share with AV1)
2 : COMPONENT (individual)
0 : Without Sound Menu
TONE-CTRL
1 : TONE
2 : EQUALIZER
3 : Without Sound Menu (GA8P)
AUTO-OFF
DIS/ENA
0 : Standby Mode
LAST POWER
1 : Last Memory
0 : No Set Up
SETUP-FLAG
1 : AUTO Set Up
AV MODE
DIS/ENA
MP-IN
DIS/ENA
S-BOOSTER
DIS/ENA
FORCE-COL
DIS/ENA
0 : ENGLISH
INIT-LANG
1 : SPANISH
2 : PORTUGUESE
LNA TUNER
LANG-SEL
Portuguese / French / Spanish
0 : CH /ͪ, VOL+/1 : /, /
0 : 7-bit volume table
VOL-TABLE
1 : 8-bit volume table
0 : EZ Setup Same as GA6 Brazil
AUTO-JUDGEMENT
1 : EZ Setup Same as GA6 LAG
WHITE-OUT
DIS/ENA
H-SYNC JUDGE
DIS/ENA
CHSET COLOR
DIS/ENA
DEMO
DIS/ENA
FLAT
DIS/ENA
0 : No AV
1 : Rear
F/R-AV
2 : Front
3 : Rear & Front
DIS/ENA
SPEAKER
0 : Old Vol-Table
VOL-CURVE
1 : New Vol-Table
0 : -105 ~ 0
CONTRAST TABLE 1 : -60 ~ 0
2 : -30 ~ 0
0 : -60 ~ +60
BRIGHTNESS TABLE
1 : -30 ~ +30
ARROW-KEY
* POWER ON BY CH-UP / DOWN KEY.
5–5
Range
INITIAL
DATA
Setting Data
0/1
0
0
0/1
0/1
0/1
0/1
1
0
0
1
0
1
0
1
0/1
1
1
0/1
1
0
0…2
1
0
0…3
1
3
0/1
1
1
0/1
0
0
0/1
1
1
0/1
0/1
0/1
0/1
1
0
0
0
0
0
0
0
0…2
0
1
0…7
7
1
0/1
1
0
0/1
0
0
0/1
1
1
0/1
0/1
0/1
0/1
0/1
0
1
0
1
1
0
1
0
1
1
0…3
3
3
0/1
1
0
0/1
0
1
0…2
0
0
0/1
0
0
21G-FX10L(A)
ADJUSTMENT PRECAUTION : Make sure TV Set is in "NORMAL CONDITION" before switch to Service Mode for Adjustment.
PIF ADJUSTMENT CHECKING
NO
1
ADJUSTMENT POINT
RF-AGC
TAKE OVER POINT
ADJUSTMENT
(I2C BUS CONTROL)
(AUTO & MANUAL ADJ)
ADJUSTMENT CONDITION/PROCEDURE
(1) Receive the "US 10 CH HALF Color Bar" signal.
Signal Strength: 56 ± 1dBμV (75 ohm open)
(2) Connect the oscilloscope to JA402 (Tuner's AGC Terminal) as shown in
figure 3-1.
+ OSCILLOSCOPE
0.1V
JA402
+
BIAS BOX
TV SET
Bias Box : about 4.5V
Fig. 3-1
(3) Call V09 in service mode. Adjust the V09 bus data to obtain the Tuner
output pin drop 0.1V below maximum voltage.
(4) Change the antenna input signal to 63 ~ 67dBμV, and make sure there
is no noise.
(5)Turn up the input signal to 90 ~ 95 dBμV to be sure that there is no cross
modulation beat.
WAVEFORM OR OTHERS
* for Auto ADJ
1)Receive "NTSC COLOUR BAR" signal
signal strength : 56 ± 1 dBμV (75 ohm open).
1) Go to service mode.
2) Go to service data V09 , press R/C to operate
"Auto-AGC" key and confirm the OK display
on the screen
3) If appear red display with NG sign, increase data some
step and please repeat step 2.
4) Proceed step 4 & 5 in manual mode.
FOCUS ADJUSTMENT
NO
1
ADJUSTMENT POINT
FOCUS
ADJUSTMENT CONDITION / PROCEDURE
(1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).
(2) Press RESET to set Picture NORMAL condition.
(3) Adjust the focus control to get the best focusing.
WAVEFORM OR REMARKS
Focusing Point (middle
of center and edge of
monoscope pattern)
H-VCO, VIF-VCO & S-TRAP fo ADJUSTMENT
NO ADJUSTMENT POINT
1 H-VCO ADJ
(I2C BUS CONTROL)
(AUTO & MANUAL ADJ)
ADJUSTMENT CONDITION / PROCEDURE
(Manual Adj)
(1) In No signal (RASTER) condition.
(2) Go to service mode, choose service data V25.
(3) Connect oscilloscope to IC801 pin13 (H-OUT), adj V25 until freq
become 15.735 ± 0.2KHz.
WAVEFORM OR OTHERS
(Auto Adj)
(1) In No signal (RASTER) condition.
(2) Go to service mode.
(3) Choose service data V25, by pressing R/C "AUTO H-VCO" key, OSD will appear "OK"
at screen.
(4) If appear "NG" pls repeat step 3.
2
VIF-VCO ADJ
(I2C BUS CONTROL)
(AUTO & MANUAL ADJ)
3
S-TRAP fo ADJ
(I2C BUS CONTROL)
(AUTO & MANUAL ADJ)
(Manual Adj)
(1) In No signal (RASTER) condition.
(2) Go to service mode, choose service data V14
(3) Connect oscilloscope to IC801 pin7 (AFT), adj V14 until voltage become
2.5 ± 0.5 V DC (Checking spec : 2.50 ± 1.5 V)
(Auto Adj)
(1) In No signal (RASTER) condition.
(2) Go to service mode, choose service data V14.
(3) Press the R/C "AUTO PIF-VCO" key, OSD will appear "OK" at screen.
(4) If appear "NG" pls repeat step 3.
(Manual ADJ)
(1) In No signal (RASTER) condition.
(2) Go to service mode, choose service data V26.
(3) Connect oscilloscope to TP 801 or IC801 pin 30, adj V26 until voltage become Min (below 5 V).
(Auto Adj)
(1) In No signal (RASTER) condition.
(2) Go to service mode, choose service data V26.
(3) Press the R/C "AUTO S-TRAP" key, OSD will appear "OK" at screen.
(4) If appear "NG" pls repeat step 3.
5–6
*NOTE:
This adjustment must be done after aging
at least 3 minutes.
21G-FX10L(A)
HORIZONTAL, VERTICAL, DEFLECTION LOOP ADJUSTMENT
NO
ADJUSTMENT POINT
1
V-SHIFT
ADJUSTMENT CONDITION / PROCEDURE
(1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).
WAVEFORM OR OTHERS
Figure
A
B
(I2C BUS CONTROL) (2) Choose the service data V07.
(3) Adjust V07 to align the center of the screen to the geometric center of CRT.
Note: B line (Monoscope middle line) must same or nearest higher position
to the A mark (Tube middle mark), refer to the attach drawing.
OK
2
V-SIZE
OK
NG
(1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).
(I2C BUS CONTROL) (2) Choose the service data V10.
(to be done after
(3) Adjust V10 bus data until the overscan become 10 ± 2.5 %.
V-shift adj)
Caution 1: Pls aging TV more than 10 minutes before adjustment
3
V-LINEARITY
(1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).
(I2C BUS CONTROL) (2) Choose the service data V29.
(3) Already preset. (Adjust this unless the linearity is achieved.)
4
VS CORRECTION
(1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).
(I2C BUS CONTROL) (2) Choose the service data V27.
(3) Already preset. (Adjust this unless the linearity is achieved.)
5
H-SHIFT
(1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).
(I2C BUS CONTROL) (2) Choose the service data V08.
(3) Adjust the V08 bus data to have a balance position to spec of A=B (as attach drawing).
(4) If cannot make it to A=B, adjust from the best point so that A slightly smaller than B.
5–7
A
B
21G-FX10L(A)
CLOSED CAPTION ADJUSTMENT
NO ADJUSTMENT POINT
1 CLOSED CAPTION
SET UP
ADJUSTMENT CONDITION / PROCEDURE
(1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz)
(2) Go to service mode, choose service data V22.
(3) Adjust the V22 bus data to have a balance position to spec of A=B
(4) After the left and right symmetrical then V22 data reduce 5 step.
WAVEFORM OR OTHERS
A
B
SCREEN, WHITE BALANCE, SUB-BRIGHTNESS & SUB-CONTRAST ADJUSTMENT (1)
NO
ADJUSTMENT POINT
1
SCREEN
ADJUSTMENT CONDITION / PROCEDURE
(1) Set the service data before adjust CRT cutoff as follows:
WAVEFORM OR OTHERS
NOTE:
ADJUSTMENT
a) V01
:
127
Service data
R/C key (Hex)
(I2C BUS CONTROL)
b) V04
:
127
R-cutoff up
A9
c) V15
:
127
R-cutoff down
69
d) V16
:
127
G-cutoff up
E9
e) V17
:
127
G-cutoff down
19
f) V18
:
64
B-cutoff up
99
g) V19
:
64
B-cutoff down
59
White
Dark
(2) Receive the window pattern or US4 CH LION HEAD Signal (NTSC 60 Hz)
(3) Go to service mode, get in Y-mute by R/C and set V23 to "1"
(4) Adjust the Screen so that cut-off line appear in low bright, then judge that whether
the cut-off data appear in Red or Green or Blue color, in this condition between
V15 = R-CUTOFF, V16=G-CUTOFF & V17= B-CUTOFF, fix the data of the color appear
in cut-off line and adj the other two cut-off line so that cut-off line color become white.
(5) Turn the screen VR of FBT so that cut-off line just disappear and use R/C to set V23 to "0".
Next disable the Y-Mute so that the picture appear in normal mode
2
WHITE BALANCE ADJ (1) WHITE (HIGH BEAM)
(to be done
after screen adj)
(I2C BUS CONTROL)
(CH 23 50IRE
WINDOW PATTERN)
First use Minolta Color Analyzer CA100, let the gun point at Dark White position
(as drawing attach), Adj V04 until LUMINANCE Y become 5 cd/m 2, then let the gun
point at White position ( as drawing attach), Adj V01 until LUMINANCE Y
become: 150 cd/m 2.
White
Adj the V18(R DRIVE) , V19(B DRIVE) until the axis of color temperature become
10700°
X : 0.278 , Y : 0.280
(2) DARK WHITE (LOW BEAM)
Let the gun point at Dark White position, if the color temperature data shift away from
50% WHITE
the data adjusted in Item 1 Screen adjustment, adjust V15,V16,V17.
Please fix the first colour appears in Screen adj item step (4) is fixed,
adj the other two so that to obtain the similar axis as above
** Repeat step 1 & 2 to get a regulated position
5–8
*Note : Use RF CH23 50IRE window pattern
21G-FX10L(A)
NO
ADJUSTMENT POINT
3
SUB-BRIGHTNESS
ADJUSTMENT CONDITION / PROCEDURE
WAVEFORM OR OTHERS
(1) In CH 23 50IRE window pattern signal condition.
(to be done after screen, (2) Using Minolta Color Analyzer CA-100, let the gun point at Dark White position
white balance adj)
US14
(as attach drawing), adjust V04 Bus data until BRIGHTNESS Y = 1.5cd/m 2
(I2C BUS CONTROL)
*Note: Final inspection data are as follows
(TV set must be in Service mode & complete with Cab-B):
Service
Luminance
Tolerance (cd/m 2)
Mode
(cd/m 2)
Upper Limit Low er Limit
Enable
1.5
+0.5
-0.5
Dark White
4
SUB-CONTRAST
(1) In CH 23 50IRE window pattern signal condition.
(to be done after screen, (2) Using Minolta Color Analyzer CA-100, let the gun point at White position
white balance adj,
US14
(as attach drawing), adjust V01 Bus data until BRIGHTNESS Y = 150cd/m 2
sub-brightness adj)
(I2C BUS CONTROL)
NOTE: Allowable Data for V01 >=90, even Y can't match the spec
*Note: Final inspection data are as follows
(TV set must be in Service mode & complete with Cab-B):
5
BEAM CURRENT
CHECK
Service
Luminance
Tolerance (cd/m 2)
Mode
(cd/m 2)
Upper Limit Low er Limit
Enable
150.0
+10
-10
White
(1) Receive US 4 CH LION HEAD Signal (NTSC 60 Hz).
(2) Press R/C to set Picture NORMAL condition.
(3) Connect the DC miliammeter between TP 603 ( + ) & TP 602 ( - )
(Full Scale: 3mA Range).
(4) Beam current must be within :
NO
1
1000 ± 100μA
ADJUSTMENT POINT
ADJUSTMENT CONDITION / PROCEDURE
SUB-TINT
(1) Receive the "US 10 CH HALF Color Bar" signal.
(2) Connect the oscilloscope to JA410 or TP853 BLUE-OUT
(I2C BUS CONTROL)
Range
: 500mV/Div (AC)
(Use Probe 10:1)
Sweep time : 10 sec/Div
WAVEFORM OR REMARKS
(3) Select the service data V02. On Y-mute using the R/C.
(4) Adjust the V02 (Sub tint) data to obtain the waveform as shown in Figure 1.1
(B-Amp Base (TP853) must be in stepping level)
*REMARK : PLEASE MAKE SURE USE RF SIGNAL DURING SUB TINT ADJUSTMENT
Fig 1-1
2
SUB COLOR
(I2C BUS CONTROL)
(to be done after
sub tint adj)
(1) Receive the "US 10 CH HALF Color Bar" signal.
(2) Make the image normal with the remote controller.
(3) Connect the oscilloscope to JA401 (TP851) RED-OUT.
Range
: 500mV/Div (AC)
Sweep time : 10 sec/Div
( Use Probe 10:1)
(4) Select the service data V03. Adjust the V03 (Sub color) data to obtain the waveform
adjustment shown in Fig. 1-2.
(5) Fig 1.2 waveforms shows that the 75% white & red portions of color bar at the same level
Cy
G
100% WHITE
*REMARK : PLEASE MAKE SURE USE RF SIGNAL DURING SUB COLOUR ADJUSTMENT
W
Y
Fig 1-2
5–9
Mg
R
B
21G-FX10L(A)
PROTECTOR OPERATION CHECKING
NO
1
2
ADJUSTMENT POINT
H, V PROTECTOR
ADJUSTMENT CONDITION / PROCEDURE
(1) Receive US 4 CH LION HEAD Signal (NTSC 60 Hz).
(2) Connect output of Bias Box to D602 cathode (C602 positive).
(3) Set voltage of Bias Box to 18V and make sure the protector is not working.
(4) Set voltage of Bias Box to 28.5V. Make sure the protector is functioned, horizontal oscilation stop
and picture disappear.
-COM has
(5) Pull out the AC cord at least 4 second before plugging in again (to make sure ohm
been reset) for the set to recover from protector mode
WAVEFORM OR OTHERS
OTHER PROTECTOR (1) Once finish rectified Electrolytic Capacitor short testing in + B line,
check all possible damaged components on +B line.
(Use random selected set for inspection)
A/V INPUT & OUTPUT CHECKING
NO
1
ADJUSTMENT POINT
VIDEO AND AUDIO
OUTPUT CHECK
ADJUSTMENT CONDITION / PROCEDURE
(1) Receive the "US 10 CH HALF Color Bar" signal.
(2) Terminate the Video output with a 75 ohm impedance.
( At signal is standard Color Bar Y/C=1/1, 87.5% Mod.)
Make sure the output is as specified (1.0 Vp-p ± 3 dB).
(3) Terminate the Audio output with a 47K ohm impedance.
( 400 Hz 100 % Mod. 47 k ohm , VOL Max. )
Set volume to max, make sure the O/P is as specified (2.5 Vp-p ± 0.5Vp-p).
2
VIDEO AND AUDIO
INPUT CHECK
(1) Using the INPUT key on the remote controller, make sure that the modes change in order of
TV, INPUT1,INPUT2 & TV again and the video & audio output are according
to the input terminal for each mode.
(2) Video cross-talk INPUT to TV checking :
a) When connect INPUT1 input, check TV also
b) When connect INPUT2 input, check TV also
3
HEADPHONE
CHECK
(1) Receive "US 4 CH LION HEAD Signal ( NTSC 60 Hz )" signal.
(2) Maximum volume , and check the headphone output with 400Hz sound and no sound
output from speaker.
5 – 10
WAVEFORM OR OTHERS
21G-FX10L(A)
FUNCTION OPERATION CHECKING (VIDEO & AUDIO) (1)
E
ADJUSTMENT CONDITION / PROCEDUR
NO ADJUSTMENT POINT
(1) Receive "US 4 CH LION HEAD Signal (NTSC 60 Hz)" signal.
PICTURE Key
1
(2) Press to Menu mode, then select Picture Mode and set to select CONTRAST.
(3) Press Volume Up/Down key to check whether the CONTRAST effect is OK or not.
2
COLOUR Key
3
BRIGHTNESS Key
4
TINT Key
5
SHARPNESS Key
6
RESET KEY
(1) Receive the "US 10 CH HALF Color Bar" signal
(2) Press to Menu mode, then select Picture Mode and set to select COLOUR.
(3) Press Volume Up/Down key to check whether the COLOUR effect is OK or not.
(1) Receive "US 4 CH LION HEAD Signal (NTSC 60 Hz)" signal.
(2) Press to Menu mode, then select Picture Mode and set to select BRIGHTNESS.
(3) Press Volume Up/Down key to check whether the BRIGHTNESS effect is OK or not
(1) Receive the "US 10 CH HALF Color Bar" signal
(2) Press to Menu mode, then select Picture Mode and select TINT.
(3) Press Volume Up/Down key to check TINT, UP for GREEN direction and
DOWN for RED direction whether is OK or not.
(1) Receive "US 4 CH LION HEAD Signal (NTSC 60 Hz)" signal.
(2) Press to Menu mode, then select Picture Mode and set to select SHARPNESS.
(3) Press Volume Up/Down key to check whether the SHARPNESS effect is OK or NOT.
(1) Once in Picture Mode , and the RESET Key is pressed,
all the setting will be present to normal setting.
PICTURE
COLOUR
BRIGHTNESS
TINT
SHARP
PICTURE NR
COLOR TEMP
7
COLOR TEMP
WAVEFORM OR REMARKS
60
0
0
0
0
OFF
Mid
(1) Receive US 4 CH LION HEAD Signal ( NTSC 60 Hz ).
(2) Set FUNCTION to select WHITE TEMP.
(3) Press Volume Up/Down key to check WHITE TEMP Option, STANDARD.
NORMAL SETTING, WARM for more REDDISH direction changing, COOL for
more BLUISH direction changing.
5 – 11
*NOTE :
In RESET Mode,when press RESET key,
will appear RESET OSD and all setting set to normal.
21G-FX10L(A)
CHECKING FUNCTION OPERATION (VIDEO & AUDIO) (2)
NO
ADJUSTMENT POINT
8
NOISE MUTE
CHECKING
ADJUSTMENT CONDITION / PROCEDURE
WAVEFORM OR REMARKS
(1) Receive mono-tone signal.
(2) Turn up the volume control to maximum, make sure the sound is
heard from the speakers. Then put the unit in no signal state.
(3) Check the sound mute is effective.
(4) Finally turn sound level of CTV to minimum.
6
OSD LANGUAGE
(1) Check OSD LANGUAGE quantity and type for respective model.
QUANTITY CHECK
MODEL
21G-FX10L(A)
10
CLOSED CAPTION
CHECKING
QUANTITY ENGLISH SPANISH
2
O
O
(1) Receive closed caption channel.
(2) Press R/C "CC" button, and the it will change from OFF to CC1 to CC2 to TEXT1 to TEXT2.
(3) Check the closed caption to make sure it is working accordingly.
SHOCK TEST CHECKING
NO
ADJUSTMENT POINT
1
SHOCK TEST
ADJUSTMENT CONDITION / PROCEDURE
WAVEFORM OR OTHERS
(1) Hit at the top of TV set for two time.
(2) Check TV set not damage and TV operation operate correctly.
ROM CORRECTION CHECKING
NO ADJUSTMENT POINT
ADJUSTMENT CONDITION / PROCEDURE
1 SOFTWARE VERSION (1) Go to SERVICE mode, press "MENU" key until the SERVICE mode display as in
WAVEFORM OR OTHERS
* OTHERS:
Figure 1 appeared.*
INFO
(2) Check the SOFTWARE VERSION status by monitoring the screen, follow the model's setting.
Model
Micon Version
CHK1
CHK2
21G-FX10L(A)
RH-IXD064WJZZQ (Software Ver. 1.35)
NO
NO
MASK: N1
SOFT : 1.35
CHK1 :NO
CHK2 :NO
Figure 1
5 – 12
21G-FX10L(A)
CHAPTER 6. WAVEFORMS
Service Manual
TV
E
Market
21G-FX10L(A)
(1) 1.92 Vp-p
(2) 4.85 Vp-p
(3) 3.70 Vp-p
(4) 3.85 Vp-p
Horiz. Rate
Horiz. Rate
Horiz. Rate
Horiz. Rate
(5) 3.01 Vp-p
(6) 4.72 Vp-p
(7) 5.70 Vp-p
(8) 1.33 Vp-p
Horiz. Rate
Vert. Rate
Horiz. Rate
Vert. Rate
(9) 2.45 Vp-p
(10) 40.80 Vp-p
(11) 1086 Vp-p
(12) 53.20 Vp-p
Horiz. Rate
Horiz. Rate
Horiz. Rate
Vert. Rate
(13) 6.78 Vp-p
(14) 144.00 Vp-p
(15) 483.00 Vp-p
(16) 118.80 Vp-p
Vert. Rate
Horiz. Rate
-
Horiz. Rate
(17) 86.60 Vp-p
(18) 94.60 Vp-p
Horiz. Rate
Horiz. Rate
6–1
21G-FX10L(A)
CHAPTER 7. CHASSIS LAYOUT
Service Manual
TV
E
Market
21G-FX10L(A)
H
G
F
E
D
C
B
A
1
2
3
4
6
5
7–1
7
8
9
10
21G-FX10L(A)
CHAPTER 8. BLOCK DIAGRAM
Service Manual
TV
E
Market
21G-FX10L(A)
H
G
F
E
D
C
B
A
1
2
3
4
6
5
8–1
7
8
9
10
21G-FX10L(A)
10
11
12
13
14
15
8–2
16
17
18
19
21G-FX10L(A)
H
G
F
E
D
C
B
A
1
2
3
4
6
5
8–3
7
8
9
10
21G-FX10L(A)
CHAPTER 9. DESCRIPTION OF SCHEMATIC DIAGRAM
Service Manual
TV
E
Market
21G-FX10L(A)
DESCRIPTION OF SCHEMATIC DIAGRAM
DESCRIPTION OF SCHEMATIC DIAGRAM
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are μF, unless otherwise noted.
(P=pF=μμF)
4. (G) indicates ±2% tolerance may be used.
5.
indicates line isolated ground.
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000μ V B & W or Color
signal.
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
indicates waveform check points (See chart,
2.
waveforms are measured from point indicated to
chassis ground.)
AND SHADED (
) COMPONENTS
= SAFETY RELATED PARTS.
MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES ET HACHRES (
):
PIECES RELATIVES A LA SECURITE.
MARQUE : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
9–1
21G-FX10L(A)
CHAPTER 10. SCHEMATIC DIAGRAM
Service Manual
TV
E
Market
21G-FX10L(A)
H
G
F
E
D
C
B
A
1
2
3
4
6
5
10 – 1
7
8
9
10
21G-FX10L(A)
10
11
12
13
14
15
10 – 2
16
17
18
19
21G-FX10L(A)
H
G
F
E
D
C
B
A
1
2
3
4
6
5
10 – 3
7
8
9
10
21G-FX10L(A)
CHAPTER 11. PRINTED WIRING BOARD ASSEMBLIES
Service Manual
TV
E
Market
21G-FX10L(A)
H
G
F
E
D
C
B
A
PWB-A : MAIN UNIT ( Wiring Side )
1
2
3
4
6
5
11 – 1
7
8
9
10
21G-FX10L(A)
H
G
F
E
D
C
B
A
PWB-A : MAIN UNIT ( Chip Parts Side )
1
2
3
4
6
5
11 – 2
7
8
9
10
21G-FX10L(A)
H
G
F
E
D
C
B
PWB-B : CRT UNIT ( Wiring Side )
A
1
2
3
4
6
5
11 – 3
7
8
9
10
21G-FX10L(A)
H
G
F
E
D
C
B
PWB-B : CRT UNIT ( Chip Parts Side )
A
1
2
3
4
6
5
11 – 4
7
8
9
10
21G-FX10L(A)
PARTS GUIDE
No. 21G-FX10L(A)
21G-FX10L(A)
MODEL
CONTENTS
PartsGuide
[1]
PICTURE TUBE
[2]
PRINTED WIRING BOARD
ASSEMBLIES ( NOT REPLACEMENT ITEM )
[3]
MAIN UNIT
[4]
CRT UNIT
[5]
MISCELLANEOUS PARTS
[6]
SUPPLIED ACCESSORIES
[7]
CABINET PARTS
[8]
PACKING PARTS ( NOT REPLACEMENT ITEM )
„
INDEX
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
21G-FX10L(A)
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[1] PICTURE TUBE
VB51QGT310X2E
RCILGA172WJZZ
QEARCA052WJZZ
!
!
BS
AM
AG
R
R
R
SEMI-ITC Picture Tube
Degaussing Coil
Ground-Part
[2] PRINTED WIRING BOARD ASSEMBLIES ( NOT REPLACEMENT ITEM )
DUNTKF472WEA6
DUNTKF473WEA6
BN
AP
-
MAIN Unit
CRT Unit
AS
AL
AE
AM
AE
AR
AE
AC
AE
AE
AG
AA
AB
AD
AD
AD
AB
AB
AB
AB
AB
AA
AA
AE
AE
AB
AC
AE
AB
AA
AA
AC
AA
AB
AE
AE
AG
AG
AC
AC
AC
AB
AC
AB
AB
AB
AB
AB
AD
AE
AB
AB
AA
AA
AA
AA
AB
AC
AC
AC
AC
AA
AA
AA
AC
AC
AF
AD
AB
AB
AG
AG
AD
AD
AB
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Tuner
LA42032E-1
LA78040B-1
I.C.
I.C.
I.C.
IM24C08W
I.C.
2SC2735//1E
2SC2235
2SC6090
2SC3198
2SC3928AR
2SD468
2SD468
2SD468
2SC3928AR
2SC3928AR
2SC3928AR
2SA1530AR
2SC3928AR
Zener Diode , 33V
Diode
Diode , DX0445CE
Diode , DX0247CE
Zener Diode , 5.1V
Diode , DXA094WJ
Diode , DX0302CE
Diode , 1SS244
Zener Diode , 27V
Diode
Diode , DXA049WJ
Diode
Zener Diode
Diode , DX0321CE
Diode , DX0255CE
Diode , DXA006WJ
Diode , DX0476CE
Diode , DX0066GE
Diode , DX0066GE
Diode , DX0066GE
Zener Diode
Diode , DX0066GE
Zener Diode
Zener Diode
Zener Diode , 8.2V
Zener Diode
Zener Diode , 5.1V
Diode , DXA044WJ
Diode , DX0247CE
Zener Diode , 5.1V
Zener Diode , 8.2V
Diode
Diode
Diode
Diode
Zener Diode
Zener Diode
Zener Diode
Zener Diode
Photodiode
Zener Diode , 10.71V
Diode
Diode
Diode , DX0066GE
Varistor
Crystal
[3] MAIN UNIT
!
!
!
!
TU201
IC301
IC501
IC701
IC751
IC801
IC1003
IC3004
Q201
Q601
Q602
Q603
Q604
Q752
Q753
Q754
Q762
Q764
Q801
Q802
Q1003
D201
D203
D392
D393
D503
D505
D510
D602
D603
D605
D606
D607
D608
D609
D610
D611
D701
D706
D707
D709
D715
D721
D722
D723
D732
D736
D750
D751
D752
D754
D757
D762
D763
D764
D801
D806
D807
D808
D809
D1001
D1002
D1005
D1008
D1081
VA701
X801
NR701
L203
L204
L601
L605
L701
L751
L802
RTUNQA037WJN1
VHILA42032E-1
VHILA78040B-1
VHISTRW5453-1
VHIKIA78R05-1
RH-IXD064WJZZQ
VHIM24C08W6-1Y
VSIMXC/C//-1Y
VS2SC2735//1EY
VS2SC2235Y/1E+
VS2SC6090++1E
VS2SC3198-G-1+
VS2SC3928AR-1Y
VS2SD468-C/-1+
VS2SD468-C/-1+
VS2SD468-C/-1+
VS2SC3928AR-1Y
VS2SC3928AR-1Y
VS2SC3928AR-1Y
VS2SA1530AR-1Y
VS2SC3928AR-1Y
VHEZJ33C+++1EY
VHDHSS4148+-1Y
RH-DX0445CEZZ
RH-DX0247CEZZ
VHEZJ5R1B++1EY
RH-DXA094WJZZY
RH-DX0302CEZZY
VHD1SS244//-1Y
RH-EXA572WJZZY
VHDHSS4148+-1Y
RH-DXA049WJZZY
VHDHSS4148+-1Y
VHEZJ5R6C++1EY
RH-DX0321CEZZY
RH-DX0255CEZZ
RH-DX0461CEZZ
RH-DX0476CEZZ
RH-DX0066GEZZY
RH-DX0066GEZZY
RH-DX0066GEZZY
VHEZJ5R6B++1EY
RH-DX0066GEZZY
VHEZJ27D+++1EY
VHEZJ12B+++1EY
VHEZJ8R2B++1EY
VHEZJ36C+++1EY
VHEZJ5R1A++1EY
RH-DXA044WJZZ
RH-DX0247CEZZ
VHEZJ5R1B++1EY
VHEZJ8R2B++1EY
VHDHSS4148+-1Y
VHDHSS4148+-1Y
VHDHSS4148+-1Y
VHDHSS4148+-1Y
RH-EXA520WJZZY
RH-EXA535WJZZY
RH-EXA535WJZZY
RH-EXA535WJZZY
RH-PX0013PEZZ
VHEZJ11A+++1EY
VHDHSS4148+-1Y
VHDHSS4148+-1Y
RH-DX0066GEZZY
RH-VXA210WJZZ
RCRSAA075WJZZ
RH-HXA013WJZZ
QJUM-0001AJFWY
VP-XF1R2K0000Y
RCILZA121WJZZ
RCILZA115WJZZ
RCILFA187WJZZ
RCILP0179CEZZ+
VP-CF220K0000Y
Jumper wire
Peaking 1.2μH
Coil
Coil
Coil
Coil
Peaking 10μH
2
21G-FX10L(A)
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[3] MAIN UNIT
L803
L808
SF201
T602
T603
T702
C207
C208
C209
C210
C211
C212
C301
C303
C305
C306
C308
C309
C310
C311
C312
C370
C371
C372
C390
C393
C394
C395
C451
C501
C505
C508
C511
C513
C514
C515
C601
C602
C604
C608
C610
C615
C617
C618
C620
C621
C635
C701
C702
C703
C705
C706
C708
C709
C710
C711
C713
C719
C743
C750
C753
C755
C756
C757
C758
C760
C761
C767
C784
C801
C803
C804
C805
C806
C811
C814
C815
C816
C818
C819
C822
C823
C825
C826
C827
VP-CF220K0000Y
VP-CF100K0000Y
RFILCA055WJQZS
RTRNFA151WJZZ
RTRNZA058WJZZ
RTRNWA382WJZZ
VCKYCY1HF103ZY
VCKYCY1HF103ZY
VCKYCY1HF103ZY
VCKYCY1HF103ZY
VCCCCY1HH820JY
VCCCCY1HH820JY
VCEA0A1EW476M+
VCKYCY1HB332KY
VCKYCY1HB332KY
VCEA0A1CW336M+
VCEA0A1CW477M+
VCFYFA1HA104J+
VCFYFA1HA104J+
VCEA0A1CW106M+
VCEA0A1CW106M+
VCEA0A1CW106M+
VCEA0A1HW225M+
VCEA0A1HW225M+
VCEA0A1CW106M+
VCEA0A1CW108M+
VCEA0A1HW225M+
VCEA0A1HW225M+
VCEA0A1CW477M+
VCFYFA1HA154J+
VCEA0A1HW107M+
VCFYAA2AA224J+
VCEA0A1HW477M+
RC-EZA332WJZZ+
VCQYTA2AA473J+
VCEACA1HC335J+
VCQYTA1HM563J+
VCEA0A1HW475M+
VCEA0A2EW336M+
VCQYTA1HM273J+
VCEA0A1EW226M+
RC-FZ0357CEN1
VCFPVC3ZA123H
VCQPBC2JB363J
VCFPKH2ED153J
VCQPBC2GB333J
VCFPKH2ED244J
RC-FZA018WJZZ
RC-KZ0029CEZZ+
RC-KZ0029CEZZ+
RC-EZA229WJZZ
VCFYFA1HA105J+
VCKYPA1HB221K+
VCQYTA1HM103J+
VCQYTA1HM103J+
VCKYPA1HB472K+
RC-KZ0102GEZZ
VCEA0A1HW476M+
VCKYPH3DB561K
VCKYPA2HB102K+
RC-EZA235WJZZ
VCEA0A1CW226M+
VCEA0A1EW108M+
VCEA0A1CW226M+
VCEA0A1CW476M+
VCEA0A1CW476M+
VCEA0A1CW226M+
RC-EZB478WJZZ+
RC-KZ1018CEZZ
VCCCCY1HH101JY
VCKYCY1HB104KY
VCEA0A1HW474M+
VCKYCY1HB153KY
VCEA0A1CW476M+
VCFYFA1HA224J+
VCKYCY1HB153KY
VCCCCY1HH470JY
VCEA0A1HW474M+
VCEA0A1CW227M+
VCKYCY1HB103KY
VCKYCY1HB104KY
VCKYCY1HB104KY
VCEA0A1HW474M+
VCEA0A1HW335M+
VCKYCY1HB103KY
AB
AB
AE
AR
AD
AL
AA
AA
AA
AA
AA
AA
AB
AA
AA
AC
AC
AE
AE
AC
AC
AC
AB
AB
AC
AC
AB
AB
AC
AE
AB
AD
AB
AD
AD
AC
AB
AB
AD
AA
AB
AE
AD
AC
AD
AD
AD
AD
AC
AC
AM
AD
AB
AB
AB
AB
AC
AB
AC
AA
AD
AB
AE
AB
AB
AB
AB
AD
AC
AA
AA
AB
AA
AB
AA
AA
AA
AB
AB
AA
AA
AA
AB
AB
AA
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Peaking 22μH
Peaking 10μH
Coil
H-Volt Transformer
Transformer
Transformer
0.01 50V Ceramic
0.01 50V Ceramic
0.01 50V Ceramic
0.01 50V Ceramic
82p 50V Ceramic
82p 50V Ceramic
47 25V Electrolytic
3.3 50V Ceramic
3.3 50V Ceramic
33 16V Electrolytic
470 16V Electrolytic
0.1 50V Mylar
0.1 50V Mylar
10 16V Electrolytic
10 16V Electrolytic
10 16V Electrolytic
2.2 50V Electrolytic
2.2 50V Electrolytic
10 16V Electrolytic
1000 25V Electrolytic
2.2 50V Electrolytic
2.2 50V Electrolytic
470 16V Electrolytic
0.15 50V Mylar
100 50V Electrolytic
0.22 100V Mylar
470 50V Electrolytic
Capacitor
47 100V Mylar
3.3 50V Electrolytic
0.56 50V Mylar
4.7 50V Electrolytic
33 250V Electrolytic
0.27 50V Mylar
22 25V Electrolytic
Capacitor
12 1.8KV Metalized Polypro Film
Capacitor
Capacitor
Capacitor
Capacitor
220 275V Metalized Plastic Film
0.01 250V Ceramic
0.01 250V Ceramic
220 400V Electrolytic
Capacitor
220p 50V Ceramic
50V Mylar
50V Mylar
4700p 50V Ceramic
2kV Ceramic
47 50V Electrolytic
560p 2KV Ceramic
1000p 500V Ceramic
160V Electrolytic
22 16V Electrolytic
1800 25V Electrolytic
22 16V Electrolytic
47 16V Electrolytic
47 16V Electrolytic
22 16V Electrolytic
Capacitor
2KV Ceramic
100p 50V Ceramic
0.10 50V Ceramic
0.47 50V Electrolytic
0.15 50V Ceramic
47 16V Electrolytic
0.22 50V Mylar
0.15 50V Ceramic
47p 50V Ceramic
0.47 50V Electrolytic
220 16V Electrolytic
0.01 50V Ceramic
0.1 50V Ceramic
0.1 50V Ceramic
0.47 50V Electrolytic
3.3 50V Electrolytic
0.01 50V Ceramic
3
21G-FX10L(A)
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[3] MAIN UNIT
C828
C830
C831
C833
C834
C836
C838
C840
C841
C842
C843
C844
C845
C1002
C1003
C1007
C1008
C1013
C1016
C1017
C1018
C1019
C1020
C1021
C1043
C1081
C1850
C1860
RJ14
RJ17
RJ32
RJ34
RJ37
RJ44
RJ46
RJ47
RJ70
RJ78
RJ305
RJ310
RJ311
RJ312
RJ313
RJ314
RJ317
RJ320
R205
R206
R207
R208
R209
R216
R301
R303
R307
R308
R309
R310
R314
R315
R318
R319
R325
R326
R362
R366
R370
R371
R372
R374
R382
R384
R391
R432
R458
R459
R461
R462
R502
R503
R504
R506
R507
R513
R514
VCEA0A1HW474M+
VCKYCY1HB103KY
VCEA0A1AW477M+
VCEA0A1HW105M+
VCKYCY1HB104KY
VCKYCY1HB222KY
VCEA0A1CW477M+
VCKYCY1CF105ZY
VCKYCY1CB393KY
VCKYCY1CF105ZY
VCEA0A1HW225M+
VCEA0A1HW474M+
VCEA0A1HW474M+
VCCCCY1HH101JY
VCEA0A1CW107M+
VCEA0A1CW476M+
VCKYCY1HF103ZY
VCKYCY1HF103ZY
VCKYCY1EF104ZY
VCKYCY1HB221KY
VCEA0A1HW105M+
VCKYCY1HB102KY
VCKYCY1HB561KY
VCKYCY1EF104ZY
VCKYCY1HB103KY
VCQYTA1HM104J+
VCEA0A1HW106M+
VCCCCY1HH220JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRD-RA2BE680JY
VRS-CY1JF122JY
VRS-CY1JF121JY
VRS-CY1JF221JY
VRS-CY1JF392JY
VRS-RG3LB393J+
VRD-RA2BE122JY
VRS-CY1JF473JY
VRS-CY1JF682JY
VRD-RA2BE273JY
VRS-CY1JF561JY
VRS-CY1JF561JY
VRD-RA2BE273JY
VRS-CY1JF682JY
VRD-RA2BE680JY
VRD-RA2BE680JY
VRD-RM2HD1R0JY
VRD-RM2HD1R0JY
VRS-CY1JF102JY
VRS-CY1JF102JY
VRS-CY1JF471JY
VRS-CY1JF471JY
VRS-CY1JF472JY
VRS-CY1JF472JY
VRS-CY1JF102JY
VRS-CY1JF102JY
VRN-RL3ABR10J+
VRS-CY1JF151JY
VRS-CY1JF103JY
VRD-RA2EE750JY
VRS-CY1JF750JY
VRS-CY1JF101JY
VRS-VV3AB561J+
VRN-VV3DBR56J
VRS-CY1JF222JY
VRS-RG3AB331J+
VRD-RM2HD1R0JY
VRD-RM2HD333JY
VRD-RM2HD682JY
AB
AA
AB
AB
AA
AA
AC
AB
AB
AB
AB
AB
AB
AA
AB
AC
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AB
AB
AA
AB
AA
AA
AA
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0.47 50V Electrolytic
0.01 50V Ceramic
470 10V Electrolytic
1 50V Electrolytic
0.1 50V Ceramic
2.2 50V Ceramic
470 16V Electrolytic
1 16V Ceramic
3.9 16V Ceramic
1 16V Ceramic
2.2 50V Electrolytic
0.47 50V Electrolytic
0.47 50V Electrolytic
100p 50V Ceramic
100 16V Electrolytic
47 16V Electrolytic
0.01 50V Ceramic
0.01 50V Ceramic
0.1 25V Ceramic
220 50V Ceramic
1 50V Electrolytic
1 50V Ceramic
560 50V Ceramic
0.1 25V Ceramic
0.01 50V Ceramic
0.1 50V Mylar
10 50V Electrolytic
22p 50V Ceramic
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
68 1/8W Carbon
1.2K 1/16W Metal Oxide
120 1/16W Metal Oxide
220 1/16W Metal Oxide
3.9K 1/16W Metal Oxide
39K 3W Metal Oxide
2.7K 1/8W Carbon
47K 1/16W Metal Oxide
6.8K 1/16W Metal Oxide
27K 1/8W Carbon
560 1/16W Metal Oxide
560 1/16W Metal Oxide
27K 1/8W Carbon
6.8K 1/16W Metal Oxide
68 1/8W Carbon
68 1/8W Carbon
1 1/2W Carbon
1 1/2W Carbon
1K 1/16W Metal Oxide
1K 1/16W Metal Oxide
470 1/16W Metal Oxide
470 1/16W Metal Oxide
4.7K 1/16W Metal Oxide
4.7K 1/16W Metal Oxide
1K 1/16W Metal Oxide
1K 1/16W Metal Oxide
10 1W Metal Oxide
150 1/16W Metal Oxide
10K 1/16W Metal Oxide
75 1/8W Carbon
75 1/16W Metal Oxide
100 1/16W Metal Oxide
560 1W Metal Oxide
56 2W Metal Oxide
2.2K 1/16W Metal Oxide
330 1W Metal Oxide
1 1/2W Carbon
33K 1/2W Carbon
6.8K 1/2W Carbon
4
21G-FX10L(A)
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[3] MAIN UNIT
R520
R523
R524
R526
R601
R602
R603
R605
R607
R608
R609
R611
R612
R614
R615
R616
R617
R618
R621
R622
R625
R626
R627
R637
R638
R639
R643
R644
R662
R702
R704
R705
R706
R710
R711
R721
R726
R733
R750
R751
R752
R753
R754
R757
R758
R762
R763
R764
R772
R774
R802
R805
R806
R807
R809
R810
R811
R812
R818
R819
R820
R825
R827
R828
R832
R833
R834
R835
R836
R837
R838
R841
R1003
R1004
R1008
R1010
R1011
R1012
R1013
R1014
R1015
R1017
R1019
R1020
R1021
VRS-CY1JF682JY
VRS-CY1JF103JY
VRS-CY1JF103JY
QJUM-0001AJFWY
VRS-VV3AB181J
VRD-RA2BE393JY
VRD-RA2BE823JY
VRD-RM2HD104JY
VRS-VV3AB181J
VRD-RM2HD102JY
VRD-RM2HD330JY
VRN-RL3AB1R5J+
VRD-RM2HD270JY
VRS-CY1JF154JY
VRS-CY1JF102JY
VRS-CY1JF102JY
VRS-CY1JF123JY
VRS-CY1JF103JY
VRN-RL2HC4R7J+
VRS-RG3DB682J+
VRD-RM2HD184JY
VRS-CY1JF472JY
VRD-RA2BE222JY
VRD-RA2BE331JY
VRD-RA2BE121JY
VRD-RM2HD101JY
VRS-KT3LB103J
VRS-RG3DB221J+
VRS-CY1JF103JY
VRS-VV3DB124J
VRD-RA2BE221JY
VRN-RL3DB1R0J+
VRN-RL3DBR18J+
VRD-RM2HD1R0JY
VRD-RA2EE472JY
VRD-RA2BE153JY
VRN-SV2HCR22J
VRD-RA2BE273JY
VRS-RG3AB180J+
RR-DZ0049CEZZY
RR-DZ0049CEZZY
VRD-RM2HD124JY
VRS-RG3DB680J+
VRN-VV3AB150J
VRN-VV3AB180J
VRD-RM2HD821JY
VRD-RM2HD561JY
VRD-RM2HD681JY
VRS-CY1JF102JY
VRS-CY1JF102JY
VRS-CY1JF473JY
VRD-RA2BE101JY
VRS-CY1JF822JY
VRS-CY1JF124JY
VRD-RA2BE103JY
VRS-CY1JF103JY
VRS-CY1JF103JY
VRS-CY1JF822JY
VRS-CY1JF101JY
VRS-CY1JF223JY
QJUM-0001AJFWY
VRS-CY1JF473JY
VRD-RM2HD151JY
VRS-CY1JF153JY
VRS-CY1JF222JY
VRS-CY1JF222JY
VRS-CY1JF222JY
VRS-CY1JF181JY
VRS-CY1JF181JY
VRS-CY1JF181JY
VRS-CY1JF472JY
VRS-CY1JF333JY
VRS-CY1JF102JY
VRD-RA2BE101JY
QJUM-0001AJFWY
VRS-CY1JF104JY
VRS-CY1JF183JY
VRS-CY1JF183JY
QJUM-0001AJFWY
QJUM-0001AJFWY
VRS-CY1JF000JY
VRD-RA2BE101JY
VRD-RA2BE101JY
VRS-CY1JF183JY
VRS-CY1JF822JY
AA
AA
AA
AA
AB
AA
AA
AA
AB
AA
AA
AB
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AF
AB
AA
AB
AA
AB
AB
AA
AA
AA
AB
AA
AB
AF
AF
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
6.8K 1/16W Metal Oxide
10K 1/16W Metal Oxide
10K 1/16W Metal Oxide
Jumper wire
180 1W Metal Oxide
39K 1/8W Carbon
82K 1/8W Carbon
100K 1/2W Carbon
180 1W Metal Oxide
1K 1/2W Carbon
33 1/2W Carbon
1.5 1W Metal Film
27 1/2W Carbon
150K 1/16W Metal Oxide
1K 1/16W Metal Oxide
1K 1/16W Metal Oxide
12K 1/16W Metal Oxide
10K 1/16W Metal Oxide
4.7 1/2W Metal Oxide
6.8 2W Metal Film
180K 1/2W Carbon
4.7K 1/16W Metal Oxide
2.2K 1/8W Carbon
330 1/8W Carbon
120 1/8W Carbon
100 1/2W Carbon
Resister
220 2W Metal Film
10K 1/16W Metal Oxide
120K 1W Metal Film
220 1/8W Carbon
1 2W Metal Film
0.18 2W Metal Film
1 1/2W Carbon
4.7K 1/4W Carbon
15K 1/8W Carbon
0.22 1/2W Metal Oxide
27K 1/8W Carbon
18 1W Metal Oxide
39M 1/2W Carbon Film
39M 1/2W Carbon Film
120K 1/2W Carbon
68 2W Metal Film
15 1W Metal Oxide
18 1W Metal Oxide
820 1/2W Carbon
560 1/2W Carbon
680 1/2W Carbon
1K 1/16W Metal Oxide
1K 1/16W Metal Oxide
47K 1/16W Metal Oxide
100 1/8W Carbon
8.2K 1/16W Metal Oxide
120K 1/16W Metal Oxide
10K 1/8W Carbon
10K 1/16W Metal Oxide
10K 1/16W Metal Oxide
8.2K 1/16W Metal Oxide
100 1/16W Metal Oxide
22K 1/16W Metal Oxide
Jumper wire
47K 1/16W Metal Oxide
150 1/2W Carbon
15K 1/16W Metal Oxide
2.2K 1/16W Metal Oxide
2.2K 1/16W Metal Oxide
2.2K 1/16W Metal Oxide
180 1/16W Metal Oxide
180 1/16W Metal Oxide
180 1/16W Metal Oxide
4.7K 1/16W Metal Oxide
33K 1/16W Metal Oxide
1K 1/16W Metal Oxide
100 1/8W Carbon
Jumper wire
100K 1/16W Metal Oxide
18K 1/16W Metal Oxide
18K 1/16W Metal Oxide
Jumper wire
Jumper wire
0 1/16W Metal Oxide
100 1/8W Carbon
100 1/8W Carbon
18K 1/16W Metal Oxide
8.2K 1/16W Metal Oxide
5
21G-FX10L(A)
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[3] MAIN UNIT
!
R1022
R1025
R1026
R1027
R1028
R1030
R1032
R1040
R1041
R1042
R1044
R1046
R1047
R1048
R1049
R1074
R1087
R1092
R1800
R1873
R1874
R3002
R3003
R3005
R3006
S701
S1001
S1002
S1003
S1004
S1005
F701
FH701
FH702
J351
J402
J403
J404
J405
P302
P601
P602
P701
P702
P1001
P1002
RMC1001
RDA301
RDA501
RDA602
RDA701
RDA751
TP801
VRS-CY1JF183JY
VRS-CY1JF103JY
VRS-CY1JF183JY
VRS-CY1JF104JY
VRD-RA2BE391JY
VRD-RA2BE103JY
VRS-CY1JF103JY
VRS-CY1JF332JY
VRS-CY1JF332JY
VRS-CY1JF000JY
VRS-CY1JF104JY
VRD-RA2BE102JY
VRS-CY1JF101JY
VRS-CY1JF471JY
VRS-CY1JF105JY
VRS-CY1JF103JY
VRS-CY1JF000JY
VRS-CY1JF000JY
VRD-RA2EE474JY
VRS-CY1JF151JY
VRS-CY1JF101JY
VRS-CY1JF102JY
VRD-RA2BE101JY
VRS-CY1JF102JY
VRD-RA2BE101JY
QSW-PA006WJZZ
QSW-KA019WJZZ+
QSW-KA019WJZZ+
QSW-KA019WJZZ+
QSW-KA019WJZZ+
QSW-KA019WJZZ+
QFS-C3225CEZZ
QFSHDA008WJZZ+
QFSHDA008WJZZ+
QJAKJA020WJZZ
QJAKEA056WJ04
QJAKEA056WJ09
QJAKEA070WJ02
QTANJA136WJZZ
QPLGNA109WJZZ
QPLGNA890WJZZ
LHLDW1104PEZZ
QPLGNA792WJZZ
QPLGN0269GEZZ
LHLDW1105PEZZ
QPLGNA110WJZZ
RRMCUA052WJZZ
PRDARA420WJFW
PRDARA851WJFW
PRDAR0337PEFW
PRDARA119WJFW
PRDARA167WJFW
QPLUGP0111GEFW
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AG
AC
AC
AC
AC
AC
AC
AC
AC
AD
AB
AB
AC
AG
AB
AC
AB
AC
AB
AB
AB
AG
AC
AF
AD
AF
AD
AA
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
18K 1/16W Metal Oxide
10K 1/16W Metal Oxide
18K 1/16W Metal Oxide
100K 1/16W Metal Oxide
390 1/8W Carbon
10K 1/8W Carbon
10K 1/16W Metal Oxide
3.3K 1/16W Metal Oxide
3.3K 1/16W Metal Oxide
0 1/16W Metal Oxide
100K 1/16W Metal Oxide
1K 1/8W Carbon
100 1/16W Metal Oxide
470 1/16W Metal Oxide
1M 1/16W Metal Oxide
10K 1/16W Metal Oxide
0 1/16W Metal Oxide
0 1/16W Metal Oxide
470K 1/4W Carbon
150 1/16W Metal Oxide
100 1/16W Metal Oxide
1K 1/16W Metal Oxide
100 1/8W Carbon
1K 1/16W Metal Oxide
100 1/8W Carbon
Switch , POWER
Switch , CH UP
Switch , CH DOWN
Switch , VOL UP
Switch , VOL DOWN
Switch , MENU
Fuse , 3.15A 250V
Fuse Holder
Fuse Holder
Jack
Jack
Jack
Jack
Jack
Plug ,4Pin(S)
Plug ,6Pin(F)
Plug
Plug ,2Pin(M)
Plug ,2Pin
Plug
Plug ,5Pin(BC)
Remote Receiver
Heat Sink for IC301
Heat Sink for IC501
Heat Sink for Q602
Heat Sink for IC701
Heat Sink for IC751
Plug
AC
AC
AC
AB
AA
AA
AB
AB
AC
AA
AA
AA
AA
AA
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
BF422+
BF422+
BF422+
2SA1530AR
Zener Diode
820p 50V Ceramic
560p 50V Ceramic
560p 50V Ceramic
10000p 1.5KV Ceramic
390 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
47 1/16W Metal Oxide
390 1/16W Metal Oxide
390 1/16W Metal Oxide
18K 2W Metal Film
18K 2W Metal Film
18K 2W Metal Film
10 1/8W Carbon
120 1/16W Metal Oxide
120 1/16W Metal Oxide
120 1/16W Metal Oxide
3.3K 1/2W Carbon
3.3K 1/2W Carbon
3.3K 1/2W Carbon
3.9K 1/16W Metal Oxide
390 1/16W Metal Oxide
1.5K 1/16W Metal Oxide
560 1/8W Carbon
[4] CRT UNIT
!
!
!
Q853
Q854
Q855
Q894
D898
C851
C852
C853
C880
R849
R850
R851
R852
R854
R855
R859
R861
R863
R864
R876
R877
R878
R880
R881
R882
R891
R892
R894
R895
VSBF422++++2+
VSBF422++++2+
VSBF422++++2+
VS2SA1530AR-1Y
VHD1N4148//-1Y
VCKYPA1HB821K+
VCKYPA1HB561K+
VCKYPA1HB561K+
RC-KZ018JCEZZ
VRS-CY1JF391JY
VRS-CY1JF470JY
VRS-CY1JF470JY
VRS-CY1JF470JY
VRS-CY1JF391JY
VRS-CY1JF391JY
VRS-RG3DB183J+
VRS-RG3DB183J+
VRS-RG3DB183J+
VRD-RA2BE100JY
VRS-CY1JF121JY
VRS-CY1JF121JY
VRS-CY1JF121JY
VRD-RM2HD332JY
VRD-RM2HD332JY
VRD-RM2HD332JY
VRS-CY1JF392JY
VRS-CY1JF391JY
VRS-CY1JF152JY
VRD-RA2BE561JY
6
21G-FX10L(A)
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[4] CRT UNIT
P860
P880
SC851
LHLDW1104PEZZ
LHLDW1105PEZZ
QSOCVA023WJZZ
AB
AB
AE
R
R
R
Plug 4Pin (H)
Plug 5Pin (K)
Socket , 12Pin
AK
AH
AE
AD
AD
R
R
R
R
R
AC Cord
SPEAKER
SP WIRE (+--+)
H-WIRE
K-WIRE
AM
AD
AC
R
R
R
Infrared Remote Control Unit
Operation Manual
Battery
[5] MISCELLANEOUS PARTS
!
ACC701
QACCZA091WJPZ
VSP9050PA02WA
QCNW-F201WJPZ
QCNW-A230WJN1
QCNW-A788WJN1
[6] SUPPLIED ACCESSORIES
RRMCGA878WJSA
TINS-E760WJN1
UBATUA031WJZZ
7
[7] CABINET PARTS
1-1
1
1-6
1-7
1-2
1-3
1-4
2
1-5
2-1
2-2
NO.
PARTS CODE
PRICE NEW PART
RANK MARK RANK
DESCRIPTION
[7] CABINET PARTS
1
1-1
1-2
1-3
1-4
1-5
1-6
1-7
2
2-1
2-2
CCABAC304WEV4
Not Available
JBTN-A846WJKA
MSPRC0005PEFW
GCOVAD398WJSA
JBTN-A831WJKA
HBDGBA085WJKA
HDECAA030WJSA
CCABBB546WEV0
Not Available
LHLDWA101WJKZ
BC
AE
AB
AC
AC
AD
AH
BA
AD
R
R
R
R
R
R
R
R
R
Front Cabinet Ass'y
Front Cabinet
Power Button
Power Button Spring
R/C & LED Cover
Control Button
Sharp Badge
Aluminium Decoration
Rear Cabinet Ass'y
Rear Cabinet
AC Cord Hook
8
21G-FX10L(A)
[8] PACKING PARTS ( NOT REPLACEMENT ITEM )
6
SSAKA0001PEZZ
*Polyethylene Bag
Operation Manual
Batteries
4
Infra Red R/C Unit
SPAKP0099PEZZ
* Wrapping Sack
5
SPAKXC550WJZZ
*Buffer Material
3
SPAKCF689WJZZ
* Packing Case
USE 2 PACKING TAPES
FIX THE PACKING CASE
MARK *: Not replacement items
NO.
PARTS CODE
PRICE NEW PART
RANK MARK RANK
DESCRIPTION
[8] PACKING PARTS ( NOT REPLACEMENT ITEM )
3
4
5
6
SPAKCF689WJZZ
SPAKP0099PEZZ
SPAKXC550WJZZ
SSAKA0001PEZZ
-
-
Packing Case
Wrapping Sack
Buffer Material
Polyethylene Bag
9
21G-FX10L(A)
„INDEX
PARTS CODE
No.
PRICE NEW PART
RANK MARK RANK
PARTS CODE
RC-KZ018JCEZZ
RC-KZ1018CEZZ
RCRSAA075WJZZ
RFILCA055WJQZS
RH-DX0066GEZZY
[C]
CCABAC304WEV4
CCABBB546WEV0
7-1
7-2
BC
BA
R
R
22-
BN
AP
-
7-1-4
AC
R
7-1-6
7-1-7
AD
AH
R
R
7-1-5
7-1-2
AC
AE
R
R
3-P602
4-P860
3-P1001
4-P880
7-2-2
AB
AB
AB
AB
AD
R
R
R
R
R
7-1-3
AB
R
7-2-1
7-1-1
-
-
3-RDA602
3-RDA701
3-RDA751
3-RDA301
3-RDA501
AD
AF
AD
AC
AF
R
R
R
R
R
5-ACC701
55513-F701
3-FH701
3-FH702
3-J402
3-J403
3-J404
3-J351
3-L203
3-R526
3-R820
3-R1008
3-R1013
3-R1014
3-P702
3-P302
3-P1002
3-P701
3-P601
3-TP801
4-SC851
3-S1001
3-S1002
3-S1003
3-S1004
3-S1005
3-S701
3-J405
AK
AD
AD
AE
AG
AC
AC
AC
AB
AB
AC
AD
AB
AA
AA
AA
AB
AB
AB
AB
AB
AC
AC
AA
AE
AC
AC
AC
AC
AC
AG
AG
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
3-C705
3-C753
3-C513
3-C767
3-C615
3-C701
3-L701
13-L751
3-L605
3-L601
3-C702
3-C703
3-C713
AM
AD
AD
AD
AE
AD
AD
AM
AD
AG
AG
AC
AC
AC
R
R
R
R
R
R
R
R
R
R
R
R
R
R
[D]
DUNTKF472WEA6
DUNTKF473WEA6
[G]
GCOVAD398WJSA
[H]
HBDGBA085WJKA
HDECAA030WJSA
[J]
JBTN-A831WJKA
JBTN-A846WJKA
[L]
LHLDW1104PEZZ
"
LHLDW1105PEZZ
"
LHLDWA101WJKZ
[M]
MSPRC0005PEFW
[N]
Not Available
"
[P]
PRDAR0337PEFW
PRDARA119WJFW
PRDARA167WJFW
PRDARA420WJFW
PRDARA851WJFW
[Q]
QACCZA091WJPZ
QCNW-A230WJN1
QCNW-A788WJN1
QCNW-F201WJPZ
QEARCA052WJZZ
QFS-C3225CEZZ
QFSHDA008WJZZ+
"
QJAKEA056WJ04
QJAKEA056WJ09
QJAKEA070WJ02
QJAKJA020WJZZ
QJUM-0001AJFWY
"
"
"
"
"
QPLGN0269GEZZ
QPLGNA109WJZZ
QPLGNA110WJZZ
QPLGNA792WJZZ
QPLGNA890WJZZ
QPLUGP0111GEFW
QSOCVA023WJZZ
QSW-KA019WJZZ+
"
"
"
"
QSW-PA006WJZZ
QTANJA136WJZZ
[R]
RC-EZA229WJZZ
RC-EZA235WJZZ
RC-EZA332WJZZ+
RC-EZB478WJZZ+
RC-FZ0357CEN1
RC-FZA018WJZZ
RCILFA187WJZZ
RCILGA172WJZZ
RCILP0179CEZZ+
RCILZA115WJZZ
RCILZA121WJZZ
RC-KZ0029CEZZ+
"
RC-KZ0102GEZZ
"
"
"
"
RH-DX0247CEZZ
"
RH-DX0255CEZZ
RH-DX0302CEZZY
RH-DX0321CEZZY
RH-DX0445CEZZ
RH-DX0461CEZZ
RH-DX0476CEZZ
RH-DXA044WJZZ
RH-DXA049WJZZY
RH-DXA094WJZZY
RH-EXA520WJZZY
RH-EXA535WJZZY
"
"
RH-EXA572WJZZY
RH-HXA013WJZZ
RH-IXD064WJZZQ
RH-PX0013PEZZ
RH-VXA210WJZZ
RR-DZ0049CEZZY
"
RRMCGA878WJSA
RRMCUA052WJZZ
RTRNFA151WJZZ
RTRNWA382WJZZ
RTRNZA058WJZZ
RTUNQA037WJN1
[S]
SPAKCF689WJZZ
SPAKP0099PEZZ
SPAKXC550WJZZ
SSAKA0001PEZZ
[T]
TINS-E760WJN1
[U]
UBATUA031WJZZ
[V]
VB51QGT310X2E
VCCCCY1HH101JY
"
VCCCCY1HH220JY
VCCCCY1HH470JY
VCCCCY1HH820JY
"
VCEA0A1AW477M+
VCEA0A1CW106M+
"
"
"
VCEA0A1CW107M+
VCEA0A1CW108M+
VCEA0A1CW226M+
"
"
VCEA0A1CW227M+
VCEA0A1CW336M+
VCEA0A1CW476M+
"
"
"
VCEA0A1CW477M+
"
"
VCEA0A1EW108M+
VCEA0A1EW226M+
VCEA0A1EW476M+
VCEA0A1HW105M+
"
VCEA0A1HW106M+
10
No.
4-C880
3-C784
3-X801
3-SF201
3-D706
3-D707
3-D709
3-D721
3-D1081
3-D393
3-D752
3-D610
3-D510
3-D609
3-D392
3-D611
3-D701
3-D751
3-D606
3-D505
3-D806
3-D807
3-D808
3-D809
3-D603
3-NR701
3-IC801
3-D1001
3-VA701
3-R751
3-R752
63-RMC1001
3-T602
3-T702
3-T603
3-TU201
PRICE NEW PART
RANK MARK RANK
AC
AC
AF
AE
AC
AC
AC
AC
AC
AE
AE
AE
AE
AE
AE
AG
AG
AD
AC
AC
AB
AC
AC
AC
AA
AD
AR
AC
AC
AF
AF
AM
AG
AR
AL
AD
AS
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
8-3
8-4
8-5
8-6
-
-
6-
AD
R
6-
AC
R
13-C801
3-C1002
3-C1860
3-C815
3-C211
3-C212
3-C831
3-C311
3-C312
3-C370
3-C390
3-C1003
3-C393
3-C755
3-C757
3-C761
3-C818
3-C306
3-C758
3-C760
3-C806
3-C1007
3-C308
3-C451
3-C838
3-C756
3-C610
3-C301
3-C833
3-C1018
3-C1850
BS
AA
AA
AA
AA
AA
AA
AB
AC
AC
AC
AC
AB
AC
AB
AB
AB
AB
AC
AB
AB
AB
AC
AC
AC
AC
AE
AB
AB
AB
AB
AB
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
21G-FX10L(A)
PARTS CODE
VCEA0A1HW107M+
VCEA0A1HW225M+
"
"
"
"
VCEA0A1HW335M+
VCEA0A1HW474M+
"
"
"
"
"
VCEA0A1HW475M+
VCEA0A1HW476M+
VCEA0A1HW477M+
VCEA0A2EW336M+
VCEACA1HC335J+
VCFPKH2ED153J
VCFPKH2ED244J
VCFPVC3ZA123H
VCFYAA2AA224J+
VCFYFA1HA104J+
"
VCFYFA1HA105J+
VCFYFA1HA154J+
VCFYFA1HA224J+
VCKYCY1CB393KY
VCKYCY1CF105ZY
"
VCKYCY1EF104ZY
"
VCKYCY1HB102KY
VCKYCY1HB103KY
"
"
"
VCKYCY1HB104KY
"
"
"
VCKYCY1HB153KY
"
VCKYCY1HB221KY
VCKYCY1HB222KY
VCKYCY1HB332KY
"
VCKYCY1HB561KY
VCKYCY1HF103ZY
"
"
"
"
"
VCKYPA1HB221K+
VCKYPA1HB472K+
VCKYPA1HB561K+
"
VCKYPA1HB821K+
VCKYPA2HB102K+
VCKYPH3DB561K
VCQPBC2GB333J
VCQPBC2JB363J
VCQYTA1HM103J+
"
VCQYTA1HM104J+
VCQYTA1HM273J+
VCQYTA1HM563J+
VCQYTA2AA473J+
VHD1N4148//-1Y
VHD1SS244//-1Y
VHDHSS4148+-1Y
"
"
"
"
"
"
"
"
VHEZJ11A+++1EY
VHEZJ12B+++1EY
No.
3-C505
3-C371
3-C372
3-C394
3-C395
3-C843
3-C826
3-C804
3-C816
3-C825
3-C828
3-C844
3-C845
3-C602
3-C719
3-C511
3-C604
3-C515
3-C620
3-C635
3-C617
3-C508
3-C309
3-C310
3-C706
3-C501
3-C811
3-C841
3-C840
3-C842
3-C1016
3-C1021
3-C1019
3-C819
3-C827
3-C830
3-C1043
3-C803
3-C822
3-C823
3-C834
3-C805
3-C814
3-C1017
3-C836
3-C303
3-C305
3-C1020
3-C207
3-C208
3-C209
3-C210
3-C1008
3-C1013
3-C708
3-C711
4-C852
4-C853
4-C851
3-C750
3-C743
3-C621
3-C618
3-C709
3-C710
3-C1081
3-C608
3-C601
3-C514
4-D898
3-D602
3-D203
3-D605
3-D607
3-D762
3-D763
3-D764
3-D801
3-D1005
3-D1008
3-D1002
3-D723
PRICE NEW PART
RANK MARK RANK
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AD
AC
AD
AD
AD
AD
AE
AE
AD
AE
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AA
AA
AC
AD
AC
AB
AB
AA
AA
AB
AD
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
PARTS CODE
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
VHEZJ27D+++1EY
VHEZJ33C+++1EY
VHEZJ36C+++1EY
VHEZJ5R1A++1EY
VHEZJ5R1B++1EY
"
VHEZJ5R6B++1EY
VHEZJ5R6C++1EY
VHEZJ8R2B++1EY
"
VHIKIA78R05-1
VHILA42032E-1
VHILA78040B-1
VHIM24C08W6-1Y
VHISTRW5453-1
VP-CF100K0000Y
VP-CF220K0000Y
"
VP-XF1R2K0000Y
VRD-RA2BE100JY
VRD-RA2BE101JY
"
"
"
"
"
VRD-RA2BE102JY
VRD-RA2BE103JY
"
VRD-RA2BE121JY
VRD-RA2BE122JY
VRD-RA2BE153JY
VRD-RA2BE221JY
VRD-RA2BE222JY
VRD-RA2BE273JY
"
"
VRD-RA2BE331JY
VRD-RA2BE391JY
VRD-RA2BE393JY
VRD-RA2BE561JY
VRD-RA2BE680JY
"
"
VRD-RA2BE823JY
VRD-RA2EE472JY
VRD-RA2EE474JY
VRD-RA2EE750JY
VRD-RM2HD101JY
VRD-RM2HD102JY
VRD-RM2HD104JY
VRD-RM2HD124JY
VRD-RM2HD151JY
VRD-RM2HD184JY
VRD-RM2HD1R0JY
"
"
"
VRD-RM2HD270JY
VRD-RM2HD330JY
VRD-RM2HD332JY
"
"
VRD-RM2HD333JY
VRD-RM2HD561JY
VRD-RM2HD681JY
VRD-RM2HD682JY
VRD-RM2HD821JY
VRN-RL2HC4R7J+
VRN-RL3AB1R5J+
VRN-RL3ABR10J+
VRN-RL3DB1R0J+
VRN-RL3DBR18J+
VRN-SV2HCR22J
VRN-VV3AB150J
VRN-VV3AB180J
VRN-VV3DBR56J
VRS-CY1JF000JY
"
"
"
"
11
No.
3-D722
3-D201
3-D736
3-D750
3-D503
3-D754
3-D715
3-D608
3-D732
3-D757
3-IC751
3-IC301
3-IC501
3-IC1003
3-IC701
3-L808
3-L802
3-L803
3-L204
4-R864
3-R805
3-R1004
3-R1017
3-R1019
3-R3003
3-R3006
3-R1046
3-R809
3-R1030
3-R638
3-R301
3-R721
3-R704
3-R627
3-R308
3-R314
3-R733
3-R637
3-R1028
3-R602
4-R895
3-R205
3-R318
3-R319
3-R603
3-R711
3-R1800
3-R459
3-R639
3-R608
3-R605
3-R753
3-R827
3-R625
3-R325
3-R326
3-R507
3-R710
3-R612
3-R609
4-R880
4-R881
4-R882
3-R513
3-R763
3-R764
3-R514
3-R762
3-R621
3-R611
3-R391
3-R705
3-R706
3-R726
3-R757
3-R758
3-R503
3-RJ14
3-RJ17
3-RJ32
3-RJ34
3-RJ37
PRICE NEW PART
RANK MARK RANK
AB
AA
AB
AB
AB
AB
AB
AB
AB
AB
AE
AL
AE
AE
AM
AB
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AB
AB
AB
AB
AB
AB
AA
AA
AA
AA
AA
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
21G-FX10L(A)
PARTS CODE
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
"
VRS-CY1JF101JY
"
"
"
VRS-CY1JF102JY
"
"
"
"
"
"
"
"
"
"
VRS-CY1JF103JY
"
"
"
"
"
"
"
"
"
VRS-CY1JF104JY
"
"
VRS-CY1JF105JY
VRS-CY1JF121JY
"
"
"
VRS-CY1JF122JY
VRS-CY1JF123JY
VRS-CY1JF124JY
VRS-CY1JF151JY
"
VRS-CY1JF152JY
VRS-CY1JF153JY
VRS-CY1JF154JY
VRS-CY1JF181JY
"
"
VRS-CY1JF183JY
"
"
"
"
VRS-CY1JF221JY
VRS-CY1JF222JY
"
"
"
VRS-CY1JF223JY
VRS-CY1JF332JY
"
VRS-CY1JF333JY
VRS-CY1JF391JY
"
"
"
VRS-CY1JF392JY
"
VRS-CY1JF470JY
No.
3-RJ44
3-RJ46
3-RJ47
3-RJ70
3-RJ78
3-R1015
3-R1042
3-R1087
3-R1092
3-RJ305
3-RJ310
3-RJ311
3-RJ312
3-RJ313
3-RJ314
3-RJ317
3-RJ320
3-R462
3-R818
3-R1047
3-R1874
3-R362
3-R366
3-R382
3-R384
3-R615
3-R616
3-R772
3-R774
3-R1003
3-R3002
3-R3005
3-R458
3-R523
3-R524
3-R618
3-R662
3-R810
3-R811
3-R1025
3-R1032
3-R1074
3-R1010
3-R1027
3-R1044
3-R1049
3-R207
4-R876
4-R877
4-R878
3-R206
3-R617
3-R807
3-R432
3-R1873
4-R894
3-R828
3-R614
3-R835
3-R836
3-R837
3-R1011
3-R1012
3-R1020
3-R1022
3-R1026
3-R208
3-R504
3-R832
3-R833
3-R834
3-R819
3-R1040
3-R1041
3-R841
4-R849
4-R854
4-R855
4-R892
3-R209
4-R891
4-R850
PRICE NEW PART
RANK MARK RANK
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
PARTS CODE
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
"
"
VRS-CY1JF471JY
"
"
VRS-CY1JF472JY
"
"
"
VRS-CY1JF473JY
"
"
VRS-CY1JF561JY
"
VRS-CY1JF682JY
"
"
VRS-CY1JF750JY
VRS-CY1JF822JY
"
"
VRS-KT3LB103J
VRS-RG3AB180J+
VRS-RG3AB331J+
VRS-RG3DB183J+
"
"
VRS-RG3DB221J+
VRS-RG3DB680J+
VRS-RG3DB682J+
VRS-RG3LB393J+
VRS-VV3AB181J
"
VRS-VV3AB561J+
VRS-VV3DB124J
VS2SA1530AR-1Y
"
VS2SC2235Y/1E+
VS2SC2735//1EY
VS2SC3198-G-1+
VS2SC3928AR-1Y
"
"
"
"
VS2SC6090++1E
VS2SD468-C/-1+
"
"
VSBF422++++2+
"
"
VSIMXC/C//-1Y
VSP9050PA02WA
12
No.
4-R851
4-R852
3-R370
3-R371
3-R1048
3-R372
3-R374
3-R626
3-R838
3-R303
3-R802
3-R825
3-R309
3-R310
3-R307
3-R315
3-R520
3-R461
3-R806
3-R812
3-R1021
3-R643
3-R750
3-R506
4-R859
4-R861
4-R863
3-R644
3-R754
3-R622
3-R216
3-R601
3-R607
3-R502
3-R702
3-Q802
4-Q894
3-Q601
3-Q201
3-Q603
3-Q604
3-Q762
3-Q764
3-Q801
3-Q1003
3-Q602
3-Q752
3-Q753
3-Q754
4-Q853
4-Q854
4-Q855
3-IC3004
5-
PRICE NEW PART
RANK MARK RANK
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AF
AB
AB
AB
AB
AB
AB
AB
AB
AC
AB
AB
AB
AB
AB
AB
AE
AE
AA
AB
AB
AB
AB
AB
AG
AD
AD
AD
AC
AC
AC
AC
AH
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
EndPage
2010 BY
SHARP CORPORATION
CORPORATION
COPYRIGHT
COPYRIGHT © XXXX
BYSHARP
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form
or by any
means, electronic,
mechanical,
COPYRIGHT
© XXXX
BYSHARP
CORPORATION
photocopying, recording, or otherwise, without
priorALL
written
permission
of the publisher.
RIGHTS
RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
RQ0155-S
Jun 2010 Printed in Malaysia
Design and Production Information
Design
:SEM
Production :SMM
CHS.FLE
SHARP MANUFACTURING
CORPORATION (M) SDN. BHD
PQA DEPARTMENT
Batu Pahat, Johor,
Malaysia.
–1