Liebert® NX™ UPS
User Manual–40-200kVA, 480V, 60Hz
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
GLOSSARY OF SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
1.0
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.0
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.1
2.2
External Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Internal Inspections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2.1
2.3
Preliminary Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3.1
2.4
Identification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
UPS Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.4.1
2.4.2
2.4.3
2.5
2.6
Storing for Delayed Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Positioning the UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Environmental Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Special Considerations for Parallel Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Considerations in Moving the Liebert NX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mechanical Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.6.1
2.6.2
2.6.3
2.6.4
Clearances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Floor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Cabinets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
10
11
3.0
ELECTRICAL CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1
Power Cabling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1.1
3.1.2
3.1.3
3.1.4
3.1.5
3.1.6
3.1.7
3.2
13
14
14
15
15
15
16
Control Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.2.1
3.3
Cable Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Input Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cabling Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protective Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cabling Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitor Board Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Dry Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
Input Dry Contacts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Bypass Cabinet Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Circuit Breaker Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Dry Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EPO Input—Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
20
21
21
22
4.0
BATTERY INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.1
4.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
i
4.3
External Battery Cabinet Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
4.3.1
4.3.2
4.3.3
4.3.4
Battery Cabinets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the Battery Cabinet to the UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
25
25
26
4.4
4.5
4.6
Non-Standard Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
BCB Shunt Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Alber Monitoring System—Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.0
OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.1
Load Bus Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
5.1.1
5.1.2
5.2
Configuring Parallel Sbasystem Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.2.1
5.2.2
5.2.3
5.2.4
5.3
Performance Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
LBS Cable and Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features of Parallel System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Principles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operation Modes Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
30
32
32
Installing Parallel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.3.1
5.3.2
5.3.3
5.3.4
5.3.5
5.3.6
Conditions for Parallel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cabinet Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel Control Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emergency Power Off (EPO) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
33
33
33
33
35
6.0
UPS SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
6.1
6.2
6.3
6.4
Conformity and Standards. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Mechanical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
36
36
37
6.4.1
6.4.2
6.4.3
6.4.4
7.0
Input Rectifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
DC Intermediate Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Inverter Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Bypass Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
LIEBERT BDC™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
7.1
Normal (UPS) Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
7.1.1
7.2
7.3
7.4
Maintenance Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Locating the Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
7.4.1
7.4.2
7.4.3
7.5
Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Wiring Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Power Cable Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Input/Output Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Bolting Cabinets Together . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
ii
8.0
9.0
INSTALLATION DRAWINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
9.1
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
9.1.1
9.1.2
Bypass Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Operating Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
10.0
OPERATOR CONTROL AND DISPLAY PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
10.1
Operator Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
10.1.1 Display Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
10.2
10.3
10.4
10.5
10.6
10.7
10.8
10.9
10.10
10.11
10.12
Mimic Display Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audible Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LCD Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigation Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LCD Menus and Data Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Current Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS Status Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Types of LCD Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
81
82
83
83
84
84
85
88
88
90
91
10.12.1 Opening Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.12.2 Default Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.12.3 UPS Help Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.12.4 Screen Saver Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
91
91
92
92
10.13 Pop-Up Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
10.13.1 From Bypass to Inverter Mode With Power Interruption . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.13.2 From Inverter to Bypass Mode With Interruption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.13.3 System Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.13.4 Battery Capacity Test Confirmation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.13.5 Battery Self-Test Aborted, Condition Not Met . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.13.6 Battery Refresh Charge Aborted, Condition Not Met . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
93
93
93
93
93
11.0
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
11.1
Liebert NX Operating Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
11.1.1 Circuit Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
11.2
UPS Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
11.2.1 Startup Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
11.2.2 Verify Switching Between Operation Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
11.3
11.4
11.5
11.6
11.7
11.8
11.9
Partially De-Energize the Liebert Nx 480 with Internal Maintenance Bypass . . . . . . . . . . 98
Partially De-Energize the Liebert Nx 480 with Bypass Distribution Cabinet (BDC) . . . . . 99
De-Energize the Liebert Nx 480 with Bypass Distribution Cabinet (BDC) . . . . . . . . . . . . 100
Energize Nx 480 with Bypass Distribution Cabinet (BDC) . . . . . . . . . . . . . . . . . . . . . . . . . 100
Auto Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Emergency Shutdown With EPO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Reset After Shutdown for Emergency Stop (EPO Action) or Other Conditions . . . . . . . . . 101
iii
11.10 Battery Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
11.10.1 Battery Undervoltage Pre-Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
11.10.2 Battery End-of-Discharge (EOD) Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
11.11 Multi-Module System Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
11.11.1 Isolating One Module in a Multi-Module System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
11.11.2 Inserting One Module into a Multi-Module System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
11.11.3 Shutdown Procedure—Complete UPS and Load Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . 105
11.12 Commissioning a Parallel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
11.13 Parallel System Startup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
12.0
OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
12.1
Communication and Other User Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
12.1.1
12.1.2
12.1.3
12.1.4
12.1.5
12.2
Analog Input Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Liebert IntelliSlot Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communication and Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring Baud Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
106
106
106
107
107
LBS Mode—Load Bus Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
12.2.1 Remote Alarm Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
12.3
Replacing Dust Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
13.0
SPECIFICATIONS AND TECHNICAL DATA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
13.1
13.2
13.3
13.4
Lug Size and Torque Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable Lengths: Floor to Connection Point Inside UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable size and tightening torques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery Run Times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
111
112
114
APPENDIX A - UPS STATUS MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
FIGURES
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Cabinet arrangement—Liebert NX units and battery cabinets. . . . . . . . . . . . . . . . . . . . . . . . . . .
Cabinet arrangement—Liebert NX UPS, battery cabinets and Liebert NX bypass
distribution cabinets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Single module block diagram—dual input configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitor board U2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auxiliary terminal block detail (Monitoring Board) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input dry contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output dry contacts and EPO wiring for firmware before M170 . . . . . . . . . . . . . . . . . . . . . . . . . .
EPO wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery cabinets for Liebert NX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery cabinet—details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Battery tray and supports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Load Bus Synchronization cable connection in single module systems. . . . . . . . . . . . . . . . . . . . .
Load Bus Synchronization cable connection with multi-module systems . . . . . . . . . . . . . . . . . . .
Parallel system block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Paralleling cabinet with input and bypass circuit breakers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Paralleling cabinet with input, bypass and distribution circuit breakers . . . . . . . . . . . . . . . . . . .
Connecting system parallel control cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auxiliary dry contact cables for output breaker in multi-module system . . . . . . . . . . . . . . . . . . .
iv
11
12
14
18
19
20
21
22
24
25
26
28
29
30
31
31
33
34
Figure 19 Connecting EPO push button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 20 Single input UPS with external Liebert BDC with optional internal transformer—typical
configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 21 Liebert BDC connection to UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 22 Liebert BDC connection to Liebert NX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 23 Bolting a Liebert NXUPS to a Liebert BDC™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 24 Outline drawing, Liebert BDC™, 47" cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 25 Outline drawing, Liebert NX 40-120kVA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 26 Terminal details, 34" battery power pack system for Liebert NX 480V UPS . . . . . . . . . . . . . . . .
Figure 27 Liebert NX 80-120kVA dimensions—front and left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 28 Liebert NX 160-200kVA dimensions—front and left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 29 Liebert NX 160-200kVA dimensions—front and left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 30 Liebert NX 40-120kVA main components—typical unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 31 Liebert NX 160-200kVA dimensional view—front and left side . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 32 Liebert NX 160-200kVA dimensions continued—top and bottom view . . . . . . . . . . . . . . . . . . . . .
Figure 33 Liebert NX 160-200kVA main components—typical unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 34 Liebert NX 40-120kVA cable connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 35 Liebert NX 160-200kVA cable connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 36 Outline drawing, 33" battery power pack system, single cabinet . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 37 Terminal details, 33" battery power pack system, single cabinet Liebert NX . . . . . . . . . . . . . . .
Figure 38 Outline drawing, 49" battery power pack system, single cabinet . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 39 Terminal details, 49" battery power pack system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 40 Liebert NX 160-200kVA UPS to 49" battery cabinet interconnection . . . . . . . . . . . . . . . . . . . . . .
Figure 41 Liebert NX 40-120kVA UPS to 33" battery cabinet interconnection . . . . . . . . . . . . . . . . . . . . . . .
Figure 42 Outline drawing, Liebert NX 480V 33" parallel cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 43 Outline drawing, Liebert NX 480V 49" parallel cabinet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 44 Liebert NX 480V paralleling cabinet with input and bypass circuit breakers, main
components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 45 Liebert NX 480V paralleling cabinet main components—input, bypass and distribution
circuit breaker configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 46 Main component location drawing Liebert NX 480V, CB2, CB3, CB4 configurations . . . . . . . . .
Figure 47 Liebert NX 480V 40-120kVA UPS to Paralleling Cabinet Interconnection—Configuration
BB0, FB0, KB0 parallel connection to Liebert NX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 48 Interconnecting details for Liebert NX 40-120kVA UPS to paralleling cabinet with input,
bypass and distribution circuit breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 49 Lineup detail—Configuration CB2, CB3, CB4 parallel connection to Liebert NX . . . . . . . . . . . .
Figure 50 Line-up detail, bolt together description, 40-120 kVA Liebert NX . . . . . . . . . . . . . . . . . . . . . . . .
Figure 51 Single module block diagram (dual input configuration) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 52 Overview of control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 53 Detailed view of control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 54 Mimic display indicators location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 55 Location of control buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 56 Buzzer location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 57 Sections of the LCD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 58 Menu tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 59 Language selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 60 Set date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 61 Current status and history log records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 62 Opening display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 63 Default screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v
35
41
44
45
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
80
80
81
82
83
83
86
88
89
90
91
91
Figure 64
Figure 65
Figure 66
Figure 67
Figure 68
Figure 69
Figure 70
Figure 71
Help screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Screen saver window. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Circuit breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Typical parallel system block diagram with common input supply, with separate batteries
and optional output / bypass distribution panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Monitoring board (U2) auxiliary terminal block detail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Liebert IntelliSlot™ Web card display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
MultiPort 4 card pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Dust filter replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Table 1
Table 2
Table 3
Table 4
Table 5
Table 6
Table 7
Table 8
Table 9
Table 10
Table 11
Table 12
Table 13
Table 14
Table 15
Table 16
Table 17
Table 18
Table 19
Table 20
Table 21
Table 22
Table 23
Table 24
Table 25
Table 26
Table 27
Table 28
Table 29
Table 30
Table 31
Table 32
Table 33
Table 34
Table 35
Table 36
Table 37
Table 38
Table 39
Table 40
Input dry contacts at X3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Maintenance bypass cabinet interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
BCB control interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Output dry contact relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
EPO input contact relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Environmental characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
UPS mechanical characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
UPS terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Rectifier input power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Input voltage window with derating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Liebert-approved replacement batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DC intermediate circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Inverter output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Bypass input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Power cable size selection (Copper Wire Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Control wiring for Liebert NX UPS to Liebert BDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Circuit breaker schedule - Main circuit breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Main panelboard circuit breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Panelboard branch circuit breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Subfeed circuit breaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Square D I-Line panelboard circuit breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Weights, Liebert NX 40-120kVA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Battery cabinet ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Battery cabinet circuit breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
UPS terminal specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Electrical specifications, Liebert NX 160-200kVA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Mimic display status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Control buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Icons for navigation keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Description of items in UPS system window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Descriptions of UPS menus and data window items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
UPS operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Liebert NX communication options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Torque specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Battery torque rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Distance to connection points on the Liebert NX UPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Parallel system current table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
External cabinet dimensions, including side panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Cable size tightening torque at Liebert NX 40kVA UPS terminals. . . . . . . . . . . . . . . . . . . . . . . 112
Cable size tightening torque at Liebert NX 60kVA UPS terminals. . . . . . . . . . . . . . . . . . . . . . . 112
TABLES
vi
Table 41
Table 42
Table 43
Table 44
Table 45
Table 46
Table 47
Table 48
Table 49
Cable size tightening torque at Liebert NX 80kVA UPS terminals. . . . . . . . . . . . . . . . . . . . . . .
Cable size tightening torque at Liebert NX 100kVA UPS terminals. . . . . . . . . . . . . . . . . . . . . .
Cable size tightening torque at Liebert NX 120kVA UPS terminals. . . . . . . . . . . . . . . . . . . . . .
Cable size tightening torque at Liebert NX 160kVA UPS terminals. . . . . . . . . . . . . . . . . . . . . .
Cable size tightening torque at Liebert NX 200kVA UPS terminals. . . . . . . . . . . . . . . . . . . . . .
Cable size tightening torque at Liebert NX 480V Battery Cabinet DC input bus terminals. . .
Enersys battery run times in minutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C&D Dynasty battery run times in minutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UPS status messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vii
112
113
113
113
113
113
114
115
117
viii
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that should be followed during installation of your
Liebert NX UPS and ancillary equipment.
Read this manual thoroughly, paying special attention to the sections that apply to your installation,
before working with the UPS. Retain this manual for use by installing personnel.
! WARNING
Risk of heavy unit tipping over. Can cause property damage, injury and death.
Exercise extreme care when handling UPS cabinets to avoid equipment damage or injury to
personnel. The UPS module weight ranges from 1180 to 2205 lb. (535 to 1000kg).
Determine unit weight and locate center of gravity symbols
before handling the UPS. Test lift and balance the cabinet
before transporting. Never tilt equipment more than 15 degrees from vertical.
Battery manufacturers supply details of the necessary precautions to be observed when
working on, or in the vicinity of, a large bank of battery cells. These precautions should be
followed implicitly at all times.
Follow all battery safety precautions when installing, charging or servicing batteries. In
addition to the hazard of electric shock, gas produced by batteries can be explosive and
sulfuric acid can cause severe burns. When connected, the nominal battery voltage is 480VDC
and is potentially lethal.
In case of fire involving electrical equipment, use only carbon dioxide fire extinguishers or
those approved for use in fighting electrical fires.
Extreme caution is required when performing maintenance. Be constantly aware that the
UPS system contains high DC as well as AC voltages.
Check for voltage with both AC and DC voltmeters prior to making contact.
! WARNING
Risk of electric shock. Can cause injury and death.
Dangerous voltages are present within the UPS and battery enclosure. The risk of contact
with these voltages is minimized as the live component parts are housed behind a hinged,
lockable door. Further internal safety screens make the equipment protected to IP20
standards.
No risk exists to any personnel when operating the equipment in the normal manner,
following the recommended operating procedures.
All equipment maintenance and servicing procedures involve internal access and should be
carried out only by trained personnel.
! WARNING
Risk of electric shock from high leakage current. Can cause injury, property damage and
death.
High ground leakage current: Ground connection is essential before connecting the input
supply.
This equipment must be grounded in accordance with local electrical codes.
Maximum load must not exceed that shown on the UPS rating label.
Liebert® NX™
1
! WARNING
Risk of electric shock. Can cause injury and death.
Under typical operation and with all UPS doors closed, only normal safety precautions are
necessary. The area around the UPS system should be kept free of puddles of water, excess
moisture and debris.
Special safety precautions are required for procedures involving handling, installation and
maintenance of the UPS system and the batteries. Observe all safety precautions in this
manual before handling or installing the UPS system. Observe all precautions in this manual,
before as well as during performance of all maintenance procedures. Observe all battery
safety precautions before working on or near the battery.
This equipment contains several circuits that are energized with high voltage. Only
test equipment designed for troubleshooting should be used. This is particularly true for
oscilloscopes. Always check with an AC and DC voltmeter to ensure safety before making
contact or using tools. Even when the power is turned Off, dangerously high electric charges
may exist within the UPS.
All power and control wiring should be installed by a qualified electrician. All power
and control wiring must comply with the NEC and applicable local codes.
ONLY qualified service personnel should perform maintenance on the UPS system.
When performing maintenance with any part of the equipment under power, service
personnel and test equipment should be standing on rubber mats. The service personnel
should wear insulating shoes for isolation from direct contact with the floor (earth ground).
Never work alone, even if all power is removed from the equipment. A second person should
be standing by to assist and summon help in case an accident should occur.
! CAUTION
This equipment is fitted with RFI suppression filters.
Ground leakage current exceeds 3.5 mA and is less than 30 mA.
Transient and steady-state ground leakage currents, which may occur when starting the
equipment, should be taken into account when selecting instantaneous residual current
circuit breakers (RCCBs) or residual current devices (RCDs).
RCCBs must be selected sensitive to DC unidirectional pulses (Class A) and insensitive to
transient current pulses.
Note also that the ground leakage currents of the load will be carried by this RCCB or RCD.
NOTICE
Risk of improper improper electromagnetic shielding. Can cause radio communication
interference.
This unit complies with the limits for a Class A digital device, pursuant to Part 15 Subpart J
of the FCC rules. These limits provide reasonable protection against harmful interference in a
commercial environment. This unit generates, uses and radiates radio frequency energy and,
if not installed and used in accordance with this instruction manual, may cause harmful
interference to radio communications. This unit is not designed for use in a residential area.
Operation of this unit in a residential area may cause harmful interference that the user must
correct at his own expense.
2
Liebert® NX™
Battery Cabinet Precautions
The following warning applies to all battery cabinets supplied with UPS systems. Additional
warnings and cautions applicable to battery cabinets may be found in 4.0 - Battery Installation.
WARNING
Risk of electric shock. Can cause injury, property damage and death.
Special care should be taken when working with the batteries associated with this equipment.
Batteries are always live. Battery terminal voltage will exceed 480VDC and is potentially
lethal.
In addition to the hazard of electric shock, gas produced by batteries can be explosive and
sulfuric acid can cause severe burns.
Batteries should be installed, serviced and replaced only by properly trained and qualified
service personnel trained in safe battery handling methods and who have the correct PPE
(Personal Protection Equipment) and tools.
The following precautions should be observed when working with the batteries:
•
•
•
•
•
•
•
•
•
•
Eye protection should be worn to prevent injury from electrical arcs.
Remove rings, watches and all other metal objects.
Use only tools with insulated handles.
Wear rubber gloves and boots.
When replacing batteries, replace them with the same type and number of batteries or battery packs.
Do not dispose of batteries in a fire. The batteries may explode.
Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It is
toxic.
Never lay metal objects of any type on top of the batteries.
Disconnect the charging source before connecting or disconnecting battery terminals.
Determine whether the battery is grounded. If the battery is grounded, remove source of
the ground. Contact with any part of a grounded battery can result in electrical shock. The
likelihood of such shock can be reduced if such grounds are removed during installation and
maintenance.
! WARNING
Risk of heavy unit tipping. Can cause property damage, injury and death.
Internal battery strapping must be verified by manufacturer prior to moving a battery cabinet
(after initial installation).
• Battery cabinets contain non-spillable batteries.
• Keep units upright.
• Do not stack.
• Do not tilt.
Failure to heed this warning could result in smoke, fire or electric hazard.
Call 1-800-LIEBERT before moving battery cabinets (after initial installation).
! WARNING
Risk of electric shock. Can cause injury and death.
The Liebert NX’s internal batteries are connected and energized even if the UPS is turned
Off. To minimize the risk of injury, a properly trained and qualified service person should
disconnect the batteries before any maintenance is performed on the unit.
Servicing of batteries should be performed or supervised only by properly trained and
qualified personnel knowledgeable about batteries and the required precautions.
When replacing batteries, replace with the same manufacturer and type, or equivalent. See
your local Emerson® representative for a list of approved batteries.
Liebert® NX™
3
! CAUTION
Risk of replacing battery with an incorrect type. Can cause property damage injury and
death.
Dispose of used batteries according to the instructions.
When replacing batteries, replace with the same manufacturer and type, or equivalent. See
your local Emerson representative for a list of approved batteries.
4
Liebert® NX™
GLOSSARY OF SYMBOLS
Risk of electrical shock
!
Indicates caution followed by important instructions
AC input
AC output
i
-
Requests the user to consult the manual
+
Indicates the unit contains a valve-regulated lead acid battery
PbH2SO4
R
Recycle
DC voltage
Equipment grounding conductor
Bonded to ground
AC voltage
Liebert® NX™
5
Introduction
1.0
INTRODUCTION
The Liebert NX Uninterruptible Power Supply system provides continuous, high-quality AC power to
your business-critical equipment, such as telecommunications and data processing equipment.
The Liebert NX UPS is a SmartAisle™ technology, appropriate for use with the SmartAisle design
approach.
The Liebert NX supplies power that is free of the disturbances and variations in voltage and
frequency common to utility power, which is subject to brownouts, blackouts, surges and sags.
The Liebert NX utilizes the latest in high-frequency, double-conversion pulse width modulation
technology and fully digital controls to enhance its reliability and increase the ease of use.
6
Liebert® NX™
Installation
2.0
INSTALLATION
This section describes the Liebert NX environmental requirements and mechanical considerations
that must be taken into account when planning the positioning and cabling of the UPS equipment.
Because every site is unique, this section presents a guide to general procedures and practices that
should be observed by the installing engineer, rather than step-by-step installation instructions.
! WARNING
Do not apply electrical power to the UPS equipment before the arrival of the commissioning
engineer.
! WARNING
The UPS equipment should be installed by a qualified engineer in accordance with the
information contained in this section.
! WARNING
Risk of electric shock. Can cause injury and death.
Special care should be taken when working with the batteries associated with this equipment.
When connected together, the nominal battery voltage is 480VDC and is potentially lethal.
• Eye protection should be worn to prevent injury from accidental electrical arcs.
• Remove rings, watches and all other metal objects.
• Use only tools with insulated handles.
• Wear rubber gloves.
If a battery leaks electrolyte or is otherwise physically damaged, it must be replaced, stored in
a container resistant to sulfuric acid and disposed of in accordance with local regulations.
If electrolyte comes into contact with skin, the affected area should be washed immediately
with large amounts of water.
NOTE
The Liebert NX UPS can be used in TN utility system.
2.1
External Inspections
1. While the UPS system is still on the truck, inspect the equipment and shipping container(s) for
any signs of damage or mishandling. Do not attempt to install the system if damage is apparent.
If any damage is noted, file a damage claim with the shipping agency within 24 hours and contact
Emerson Network Power® Liebert Services at 1-800-LIEBERT to inform them of the damage
claim and the condition of the equipment.
2. Compare the contents of the shipment with the bill of lading. Report any missing items to the
carrier and your local Liebert representative immediately.
2.2
Internal Inspections
1. Remove any packaging material, then visually examine the UPS and battery equipment for
transit damage, both internally and externally. Report any such damage to the shipper and to
Liebert immediately.
2. Check the nameplate inside the cabinet door to verify that the model number and rating
correspond to the ones specified. Record the model number and serial number in the front of this
installation manual. This information is necessary should service be required.
3. Check for loose connections or unsecured components in the cabinet.
4. Check for shipping damage to internal components.
Liebert® NX™
7
Installation
2.2.1
Storing for Delayed Installation
If the equipment will not be installed immediately, it must be stored indoors where the humidity is no
higher than 90% and the temperature is no higher than 104°F (40°C). The storage area must protect
the Liebert NX from excessive moisture (see 6.2 - UPS Environmental).
NOTE
If the battery cabinet must remain disconnected from power for more than six (6) months, the
battery must be recharged before use. To charge the batteries, the battery cabinet must be
connected to the Liebert NX UPS and the UPS must be connected to utility power and started
up because the charger operates only while the Liebert NX UPS is operating
NOTE
When batteries are installed in a cabinet adjacent to the UPS unit, the battery—not the
UPS—dictates the designed maximum ambient operating temperature.
2.3
Preliminary Checks
2.3.1
Identification
The equipment supplied has an identification tag on the back of the main door listing the type and
size of the UPS.
2.4
UPS Location
2.4.1
Positioning the UPS
Choose a location for the UPS that offers:
•
•
•
•
•
•
•
2.4.2
Easy connection to inputs, outputs and auxiliary equipment
Enough space to service the UPS
Air circulation sufficient to expel heat produced by UPS
Protection against moisture and excessive humidity
Protection against dust and other particulate matter
Compliance with fire prevention regulations and practices
Operating environment temperature of 74-80°F (23-27°C) for maximum battery efficiency
Environmental Considerations
Before installing the Liebert NX, verify that the UPS room satisfies the environmental conditions
stipulated in 6.2 - UPS Environmental, paying particular attention to the ambient temperature
and air exchange system.
The UPS unit should be installed in a cool, dry, clean-air environment with adequate ventilation to
keep the ambient temperature within the specified operating range 32°F to 104°F (0°C to 40°C).
For optimal UPS and battery system performance and service life, maintain the operating
temperature within the range of 74-80°F, (23-27°C).
The Liebert NX UPS cooled by internal fans. Cooling air enters the unit through the front of the unit
and is exhausted out the top. To permit proper air flow and prevent overheating, do NOT block or
cover the ventilation openings or blow air down onto the unit. Ventilation clearance above the unit
must be a minimum of 8 in. (203mm).
See Table 7 for details on heat dissipation.
8
Liebert® NX™
Installation
Battery Location
Batteries must be installed in Liebert NX 480V battery cabinets or battery room. Temperature is a
major factor in determining battery life and capacity. Battery manufacturers recommend an
operating temperature of 77°F (25°C). Ambient temperatures higher than this reduce battery life;
temperatures lower than this reduce battery capacity. In a typical installation, battery temperature
should be maintained between 74°F and 80°F (23-27°C). Batteries should be placed where there are
no main heat sources or air inlets to prevent portions of batteries from being either much warmer or
much cooler than other parts of the batteries.
2.4.3
Special Considerations for Parallel Systems
1. Consider the grounding configuration of your system before finalizing module placement. For
optimal ground performance, the Liebert NX modules should be close together.
2. For optimal load-sharing performance, the UPS output cables should be approximately the same
length, plus or minus 20 percent.
3. Position modules in such a way as to minimize the length of power cables and control wiring
between UPS modules and the paralleling cabinet.
2.5
Considerations in Moving the Liebert NX
Ensure that the UPS weight is within the designated surface weight loading (lb./ft2 or kg/cm2) of any
handling equipment. See Table 7 for weights of various units.
To move the UPS and optional battery cabinets:
• The Liebert NX may be rolled on its casters when moving the unit a short distance. For longer distances, move the UPS with a forklift or similar equipment to ease the relocation and to reduce
vibration.
The optional battery cabinets should be moved with a forklift or similar equipment.
! WARNING
Risk of heavy unit falling. Can cause property damage, injury and death.
Ensure that any equipment that will be used to move the Liebert NX has sufficient lifting
capacity. The Liebert NX weight ranges from 1180 to 2201 lb. (535 to 1000kg). See Table 7 for
details. The UPS presents a tipping hazard. Do not tilt the Liebert NX further than 15
degrees from vertical.
The UPS is fitted with casters—take care to prevent movement when unbolting the
equipment from its shipping pallet. Ensure adequate personnel and lifting equipment are
available when taking the Liebert NX off its shipping pallet. Do not tilt the unit more than 15
degrees from center.
! WARNING
Risk of heavy unit falling. Can cause property damage, injury and death.
The casters are strong enough for movement across even surfaces only. Casters may fail if
they are subjected to shock loading, such as being dropped or rolled over holes in the floor or
obstructions. Such failure may cause the unit to tip over, injuring personnel and damaging
the equipment.
Care must be taken when maneuvering cabinets fitted with batteries. Keep such moves to a
minimum. For further information, see Battery Cabinet Precautions on page 3.
Final Position
When the equipment has been finally positioned, ensure that the adjustable stops are set so that the
UPS will remain stationary and stable (see 8.0 - Installation Drawings).
Liebert® NX™
9
Installation
2.6
Mechanical Considerations
The Liebert NX is constructed with a steel frame and removable panels. Top and side panels are
secured to the chassis by screws. The doors may be opened for access to power connections bars,
auxiliary terminal blocks and power switches.
The UPS comes with an operator control panel, which provides basic operational status and alarm
information. Cooling is provided by internal fans. The unit sits on four casters. Adjustable stops are
provided to prevent the UPS from moving once it has been moved to its final position.
2.6.1
Clearances
There are no ventilation grilles on the sides or rear of the UPS. The unit may be placed with the rear
against a wall and optional cabinets on either side.
To enable routine tightening of power terminations within the UPS, make sure there is sufficient
clearance in front of the Liebert NX to permit free passage of personnel with the door fully opened.
Leave a minimum of 8 in. (203mm) between the top of the UPS and the ceiling to permit adequate air
circulation above the unit. Liebert recommends against using air conditioning or other systems that
blow air onto the top of the unit.
2.6.2
Floor Installation
The diagrams in 8.0 - Installation Drawings show the location of holes in the base plate for bolting
the equipment to the floor.
If the equipment is to be placed on a raised floor, it should be mounted on a pedestal that will support
the equipment point loading. Refer to the cabinet-bottom views in 8.0 - Installation Drawings to
design this pedestal.
2.6.3
Cable Entry
Cables can enter the Liebert NX from the top or bottom. Cable entry is made possible by removing a
metal plate attached to the UPS.
These plates are designed to allow the personnel to punch holes for fitting and securing the conduit.
Once the conduit holes are punched, these plates should be reattached to the UPS.
! WARNING
Risk of explosion and fire. Can cause property damage, injury and death.
To reduce the risk of fire, connect only to a circuit provided with correct amperes maximum
branch circuit overcurrent protection (see Table 8) in accordance with the National Electric
Code, ANSI/NFPA 70.
NOTE
When installing the UPS, the customer must provide a disconnect with overcurrent protection
at the output of the UPS.
System Composition
A UPS system can comprise a number of equipment cabinets, depending on the individual system
design requirements—e.g., UPS cabinet with External Bypass cabinet and Maintenance Bypass
cabinet. In general, all cabinets used will be the same height and are designed to be positioned sideby-side to form an aesthetically appealing equipment suite.
10
Liebert® NX™
Installation
2.6.4
Optional Cabinets
The Maintenance Bypass Cabinet must be cabled and bolted to the Liebert NX before the UPS and
bypass cabinet are moved into their final position. Connect the input wiring to the Maintenance
Bypass Cabinet ONLY after the units are connected and positioned.
Battery cabinets may be bolted to either side of the Liebert NX; see Figure 1.
Figure 1
Cabinet arrangement—Liebert NX units and battery cabinets
Liebert
NX
UPS
Battery
Cabinet
Battery
Cabinet
Front of Units
Battery
Cabinet
Battery
Cabinet
Battery
Cabinet
Liebert
NX
UPS
Front of Units
Liebert
NX
UPS
Liebert
NX
UPS
Front of Units
Battery
Cabinet
Liebert
NX
UPS
Battery
Cabinet
Battery
Cabinet
Battery
Cabinet
Front of Units
Liebert
NX
UPS
Multi-Module
Parallel Cabinet
Front of Units
Liebert® NX™
Battery
Cabinet
11
Liebert
NX
UPS
Battery
Cabinet
Liebert
NX
UPS
Battery
Cabinet
Installation
Figure 2
Cabinet arrangement—Liebert NX UPS, battery cabinets and Liebert NX bypass distribution
cabinets
Battery
Cabinet
Liebert
NX
UPS
Liebert NX
Bypass
Distribution
Cabinet
Front of Units
Battery
Cabinet
Battery
Cabinet
Battery
Cabinet
Liebert
NX
UPS
Liebert NX
Bypass
Distribution
Cabinet
Front of Units
12
Liebert® NX™
Electrical Connections
3.0
ELECTRICAL CONNECTIONS
The UPS requires both power and control cabling once it has been mechanically installed. All control
cables must run separate from power cables in metal conduits or metal ducts that are electrically
bonded to the metalwork of the cabinets to which they are connected.
! WARNING
Risk of electrical shock. Can cause injury and death.
Before connecting input power to the Liebert NX, ensure that you are aware of the location
and operation of the overcurrent protection devices that connect the UPS input/bypass supply
to the power distribution panel.
De-energize and lockout or tagout all incoming high- and low-voltage power circuits before
installing cables or making any electrical connections.
3.1
Power Cabling
3.1.1
Cable Rating
The main factors affecting the choice and size of cable are voltage, current (also taking into account
overcurrent), room temperature and conditions of installation of the cable.
The power cables of the system must be sized with respect to the following description:
• UPS input cables - The UPS input cables must be sized for the maximum input current, including the maximum battery recharge current, given in Table 8, with respect to the unit rating and
the input AC voltage.
• UPS bypass and output cables - The bypass and output cables must be sized for the nominal
output current, given in Table 8, with respect to the unit rating and the output AC voltage.
• Battery cables - When connecting an external battery cabinet, the battery cables must be sized
for the battery discharge current at the end-of-discharge voltage, as given in Table 8, with
respect to the unit rating.
NOTE
Table 8 gives nominal currents for determining the size of UPS power cables. Other important
factors to consider include cable route length and coordination with protective devices.
The power cables can be sized to suit the UPS unit rating according to Table 8.
NOTE
When installing a Liebert NX with Softscale™ capability Liebert recommends sizing the input,
bypass and output cabling for the UPS’s maximum rating. Properly sizing the cable will
reduce the work required to upgrade the UPS.
Lug Size and Torque Requirements
Refer to Table 34 for lug size and torque requirements.
Liebert® NX™
13
Electrical Connections
3.1.2
UPS Input Configuration
Figure 3 illustrates the Liebert NX in a split bypass (dual-input) configuration. In this configuration,
the Static Bypass and the Maintenance Bypass lines are supplied from a separate feed from the Main
input. Both sources must be protected externally with properly sized protective devices. By default,
the unit ships with internal links installed between the bypass input and main input (Single Input
configuration). To wire the unit as a dual input UPS, remove the links and wire the bypass to the
input bus bars, then wire the main input directly to CB1 (see Figure 3).
Figure 3
Single module block diagram—dual input configuration
3-Phase
3W + Gnd
Internal Maintenance Bypass
3-Phase
3W + Gnd
Static Bypass
Rectifier
AC Input
Inverter
3-Phase
3W + Gnd
AC Output
Converter
UPS Cabinet
2W + Gnd
Battery Cabinet
3.1.3
Cabling Guidelines
The following are guidelines only and are superseded by local regulations and codes of practice where
applicable. Use wiring rated at 75°C or greater.
1. The ground conductor should be sized in accordance with the input overcurrent protection device
data in Table 8. The ground cable connecting the UPS to the main ground system must follow the
most direct route possible. Control wiring and power wiring must be run in separate conduit.
Output and input cables must be run in separate conduit.
2. Consider using paralleled smaller cables for heavy currents—this can ease installation.
3. When sizing battery cables, a maximum voltage drop of 4VDC is permissible at the current
ratings in UPS terminal. For terminal connection sizing, see Table 8.
4. In most installations, especially parallel multi-module systems, the load equipment is connected
to a distribution network of individually protected busbars fed by the UPS output, rather than
connected directly to the UPS itself. When this is the case, the UPS output cables can be rated to
suit the individual distribution network demands rather than being fully load-rated.
NOTE
If more load is added to the distribution panel, the unit’s cabling must be resized.
5. When laying power cables, do not form coils; this will help avoid increasing formation of
electromagnetic interference.
14
Liebert® NX™
Electrical Connections
3.1.4
Cable Connections
The rectifier input, bypass and output are easily accessible from the front of the unit for installation.
All require lug type terminations. They are connected to busbars on the front side of the Liebert NX
and below the circuit breaker, as shown in Figure 3. These busbars are accessible when the front
side panel is removed. Busbars to connect external batteries are accessible from the front of the UPS.
NOTE
External connection access requires removal of a protective panel on the lower front of the UPS.
NOTE
There is no battery fuse in the UPS; the battery cabinet must include a circuit breaker
to cut off the current in case of short circuit. Refer to Table 8 for current ratings.
3.1.5
Safety Ground
The safety ground busbar is located below the Maintenance Bypass circuit breaker or to the right of
the UPS Output breaker for 160-200KVA models as shown in Figure 3. The safety ground cable must
be connected to the ground busbar and bonded to each cabinet in the system.
All cabinets and cable conduit should be grounded in accordance with local regulations.
! WARNING
Risk of electrical shock from ground fault. Can cause injury and death.
Failure to follow proper grounding procedures can result in electric shock hazard to personnel
or the risk of fire, should a ground fault occur.
NOTE
Proper grounding significantly reduces electromagnetic interference problems in systems.
NOTE
The ground busbar is easily accessible when the lower protective cover plate is removed.
3.1.6
Protective Devices
For safety, it is necessary to install circuit breakers in the input AC supply and external battery
battery cabinets, external to the UPS system. Given that every installation has its own
characteristics, this section provides guidelines for qualified installation engineers with knowledge of
operating practices, regulatory standards and the equipment to be installed.
UPS Rectifier and Bypass Input Supply
• Protection from excessive overcurrents and short circuits in power supply input
External overcurrent protection for the AC output circuit is to be provided. See 6.4 - UPS
Electrical Characteristics and Table 9 for overload capacity.
When an external battery supply not made by Liebert is used, the customer must provide
overcurrent protection for the battery circuit.
• Dual Input
When wiring the UPS with dual inputs, the Rectifier input and the Bypass input must be
protected separately. Size the breakers according to the input currents shown in Table 8.
Liebert® NX™
15
Electrical Connections
3.1.7
Cabling Procedure
NOTICE
Risk of improper installation. Can cause improper operation and void warranty.
The operations described in this section must be performed by authorized electricians or
qualified technical personnel. If you have any difficulties, contact your local Emerson
representative or Emerson Network Power Liebert Services.
NOTE
Hydraulic pressure pliers, combinative tools and piston ring pliers should be used to connect
AC wiring.
Once the equipment has been positioned and secured for operation, and the battery and ground
collars have been connected (see 3.1.4 - Cable Connections), connect the power cables as described
below. (Study the reference drawing in 8.0 - Installation Drawings.)
1. Verify that all incoming high and low voltage power circuits are de-energized and locked out or
tagged out before installing cables or making any electrical connections.
2. Remove the front protective cover to gain easier access to the connections busbars.
3. Connect the safety ground and bonding ground bus cables to the copper ground busbar located on
the bottom of the equipment below the power connections. All cabinets in the UPS system must be
connected to the user’s ground connection.
NOTE
The grounding bonding arrangement must comply with the National Electrical Code and all
applicable local codes.
4. Identify and make power connections with incoming cables according to Steps 5 through 11.
Common Input Connections
5. For common bypass and rectifier inputs, connect the AC input supply cables between the power
distribution panel and the UPS input busbars (A-B-C terminals) and tighten the connections to
88 lb-in. (10 N-m) using the M8 bolt provided.
Dual Input Connections
6. Remove the internal links installed between the Input circuit breaker (CB1) busbars and Bypass
Input busbars as shown in Figure 3.
7. For the bypass, connect the AC input supply cables between the power distribution panel and the
UPS Rectifier Input busbars (CB1 A-B-C terminals) and tighten the connections to 88 lb-in.
(10 N-m) using the M8 bolt provided.
8. For the Rectifier Input, connect AC input supply cables between the power distribution panel and
the UPS Rectifier Input busbars (CB1 A-B-C terminals).
16
Liebert® NX™
Electrical Connections
NOTE
Both the rectifier and bypass feeds must come from the same utility source. The UPS can be
powered from separate sources provided all the following conditions are met:
1. The transformers are delta/wye isolation transformers where the wye secondary’s are
connected to the NX 480V UPS.
2. The individual transformer used to supply the Bypass of the NX 480V is solidly bonded to
earth ground at the transformer.
3. The individual transformer used to supply the Input (rectifier) of the NX 480V is solidly
bonded to earth ground at the transformer.
4. There are no appreciable ground currents flowing between the two transformers.
5. No delta/delta (ungrounded or corner grounded) transformers are used as a source to the
NX 480V UPS.
6. No high resistance or low resistance grounds can be used in the neutral bonding path to
ground of the delta/wye isolation transformers described above in Items 2 and 3.
7. All applicable NEC standards and wiring rules are enforced.
8. The internal bypass to input (rectifier) shorting bars in the NX 480V UPS are removed.
The above all apply to single-module systems.
9. For 1+N paralleled system, the Bypass to each unit must be fed from the same utility
source.
Output System Connections—Ensure Correct Phase Rotation
10. Connect the system output cables between the UPS output busbars (A-B-C terminals) and the
critical load and tighten the connections to 88 lb-in. (10 N-m) (M8 bolt).
! WARNING
Risk of electric shock. Can cause injury and death.
If the load equipment will not be ready to accept power on the arrival of the commissioning
engineer, then ensure that the system output cables are safely isolated.
Observe the battery cable polarity. Be sure that the battery connector is made with the
correct polarity.
11. Refit all protective covers removed for cable installation.
Frequency Converter Mode
If a frequency converter configuration is used, connect the AC input supply cables to the rectifier
input busbars (A-B-C terminals). Torque to 88 lb-in (10N-m) for M8 bolts. Ensure correct phase
rotation. There will not be any AC bypass supply cables to the bypass input (A-B-C terminals) and
tighten the connections.
NOTE
The operations described in this section must be performed by authorized electricians or
qualified technical personnel. If any difficulties arise, contact Liebert at 1-800-LIEBERT.
NOTE
For frequency converter operation, ensure that the linking busbars between the bypass and the
rectifier input are removed.
Liebert® NX™
17
Electrical Connections
3.2
Control Cables
3.2.1
Monitor Board Features
Based on your site’s specific needs, the UPS may require auxiliary connections to manage the battery
system (external battery circuit breaker, battery temperature sensor), communicate with a personal
computer or provide alarm signaling to external devices or for Remote Emergency Power Off (REPO).
The monitor board, arranged for this purpose, is located on the rear of the operator access door. The
main features are:
•
•
•
•
•
•
•
Input and Output dry contacts signal (one pair of contacts of relay)
Emergency Power Off control (EPO)
Environmental parameter input interface
User communication (for data setting and user background monitor)
Liebert IntelliSlot® interface
Modem interface
Temperature detect interface
Figure 4 shows the relationship and connection between the monitoring (U2) board and other boards
in the UPS.
Figure 4
Monitor board U2
U1
DSP Control
M5
Auxiliary Power
K1
Key & LED Board
U2
Monitor Board
M3
Parallel Logic
Board
X1
User Interface
Board
18
Liebert® NX™
Electrical Connections
Figure 5
Auxiliary terminal block detail (Monitoring Board)
J8
J3
J1
LCD
J22
X7
J23
X6
J12
J9
J2
J15
PWR
MODEM
SNMP CARD
X5
J16
J17
Liebert IntelliSlot 2
J13 J21 J25
J28
J4
Liebert IntelliSlot 1
J26 J30 J10
X4
X4
J24
Liebert IntelliSlot 3
BFP INV ACF
X1
Liebert® NX™
EPO
X2
Dry in
MBC
BCB
NOTE: The black square ()
on each slot indicates Pin 1.
X3
19
Electrical Connections
3.3
Dry Contacts
The UPS provides input dry contacts and output dry contacts.
NOTE
When operating the Liebert NX with dry contacts, ESD measures must be taken or the contacts
may be damaged.
3.3.1
Input Dry Contacts
There are several input dry contacts at the X3 slot.
Figure 6
Input dry contacts
+12V
+12V
+12V
+12V
DRV
FB
GND
OL
FUSE
F_FAN
J10
T_0T
T_IT
AUX_0
J30
AUX_I
GND
BtG
ENV
J26
GEN
+12V
J4
+12V
X3
NOTE: The black square () on each slot indicates Pin 1.
Table 1
Input dry contacts at X3
Position
J4.1
J4.2
J4.3
J4.4
Name
ENV3
BtG
GEN1,2
+12V
Description
Battery Room Alarm (Normally Closed)
Battery Ground Fault Detection (Normally Closed)
Generator Detection (Normally Open)
+12V Power
1 - Must be configured using configuration software before becoming active.
2 - When activated, the charger current can be limited, via software, to a percentage of the full charger current (0-100%).
3 - Activating this feature turns the battery charger off.
3.3.2
Maintenance Bypass Cabinet Interface
J26 and J30 are the MBC interface.
Table 2
Maintenance bypass cabinet interface
Position
Name
1
Description
Input transformer over temperature (N.C.)
J26.1
T_IT
J26.2
AUX_I
Reserved
J26.3
+12V
+12V Power
J26.4
GND
Power Ground
J30.1
FUSE
Reserved
J30.2
F_FAN
Fan Fail Alarm (N.C.)
J30.3
T_OT1
Output Transformer Overtemperature (N.C.)
J30.4
AUX_O
Reserved
1
- Must be configured using configuration software before becoming active.
NOTE
All auxiliary cables of terminal must be double-insulated. The wire must be 600V, 18-16 AWG
stranded for maximum runs between 82 and 197 feet (25-60m), respectively.
20
Liebert® NX™
Electrical Connections
3.3.3
Battery Circuit Breaker Control Interface
J10 is the Battery Circuit Breaker (BCB) box interface.
Table 3
BCB control interface
Position
Name
Description
J10.1
DRV
BCB Driver Signal
J10.2
FB
BCB Contact State
J10.3
GND
J10.4
OL
Power Ground
BCB On-Line - Input - This pin will become active when
BCB interface is connected. (N.O.)
NOTE
All auxiliary cables of terminal must be double-insulated. The wire must be 600V, 18-16 AWG
stranded for maximum runs between 82 and 197 feet (25-60m), respectively.
3.3.4
Output Dry Contacts
There are three output dry contact relays at the X1 slot (see Figure 7 and Table 4).
Output dry contacts and EPO wiring for firmware before M170
NOTE: The black square on each slot
Table 4
ACF_O
ACF_S
ACF_C
J25
INV_O
INV_C
J21
BFP_O
BFP_C
J13
INV_S
X1
BFP_S
Figure 7
indicates Pin 1.
Output dry contact relays
Position
Name
Description
J13.2
BFP_O
Bypass feedback protection relay. Normally open. Closed when bypass SCR is
shorted;. 5A, 250VAC/24 VDC
J13.3
BFP_S
Bypass feedback protection relay center; 5A, 250VAC/24 VDC
J13.4
BFP_C
Bypass feedback protection relay. Normally closed. Open when bypass SCR is shorted;
5A, 250VAC/24 VDC
J21.2
INV_O
Inverter mode relay. Normally open. Closed when UPS is in inverter mode.; 5A,
250VAC/24 VDC
J21.3
INV_S
Inverter mode relay center; 5A, 250VAC/24 VDC
J21.4
INV_C
Inverter mode relay. Normally closed. Open when UPS is in inverter mode;
5A, 250VAC/24 VDC
J25.2
ACF_O
Main input fault relay. Normally open. Closed when main input is in fault;
5A, 250VAC/24 VDC
J25.3
ACF_S
Main input fault relay center; 5A, 250VAC/24 VDC
J25.4
ACF_C
Main input fault relay. Normally closed. Open when main input is in fault;
5A, 250VAC/24 VDC
NOTE
All auxiliary cables of terminal must be double-insulated. The wire must be 600V, 18-16 AWG
stranded for maximum runs between 82 and 197 feet (25-60m), respectively.
Liebert® NX™
21
Electrical Connections
3.3.5
EPO Input—Optional
The UPS has an Emergency Power Off (EPO) function operated by a button on the control panel or by
a remote contact provided by the user. The local EPO button is under a hinged, clear plastic shield.
The X2 slot, shown in Figure 8, is the remote EPO input interface. The EPO has a NO/NC contact
point that becomes active when shorting terminals X2: 3 and 4 or open terminal connection
X2: 2 and 1.
If an external Emergency Stop facility is required, it is connected terminals X2: 1 and 2 or X2: 3 and 4
of the auxiliary terminal block (X2). It also is connected to the Normally Open or Normally Closed
remote stop switch between these two terminals using shielded cable (see Figure 8 and Table 5). If
this function is not used, terminals X2: 3 and 4 must be opened and X2: 1 and 2 must be closed.
Figure 8
EPO wiring
X2
J28
EPO - NO
Table 5
EPO - NC
NOTE: The black square
indicates Pin 1.
EPO input contact relays
Position
Name
Description
J28.1
EPO_NC
EPO Activated when opened to J28.2
J28.2
EPO_NC
EPO Activated when opened to J28.1
J28.3
EPO_NO
EPO Activated when shorted to J28.4
J28.4
EPO_NO
EPO Activated when shorted to J28.3
NOTE
The Emergency Stop action within the UPS shuts down the rectifier, inverter and static
bypass. It does not internally disconnect the input power supply. To disconnect ALL power to
the UPS, open the upstream feeder breaker(s) when the remote EPO is activated.
NOTE
Normally Closed EPO – X2: 1,2, these terminals are supplied factory-linked on the monitor
board and must remain installed if using NO contacts.
NOTE
All auxiliary cables of terminal must be double-insulated. The wire must be 600V, 18-16 AWG
stranded for maximum runs between 82 and 197 feet (25-60m), respectively.
22
Liebert® NX™
Battery Installation
4.0
BATTERY INSTALLATION
4.1
Introduction
If using multiple sets of batteries connected in parallel to provide the required battery backup run
times, fit each set with an isolating device to permit working on one of the battery sets while leaving
the others in service and providing backup protection.
When replacing batteries, replace with the same manufacturer and type, or equivalent. See your
Emerson representative for a list of approved batteries.
4.2
Safety
Special care should be taken when working with the batteries associated with the Liebert NX™
system equipment. When all batteries are connected together, the battery terminal voltage may
exceed 480V and is POTENTIALLY LETHAL.
WARNING
Risk of electric shock. Can cause injury, property damage and death.
Special care should be taken when working with the batteries associated with this equipment.
Batteries are always live. Battery terminal voltage will exceed 480VDC and is potentially
lethal.
In addition to the hazard of electric shock, gas produced by batteries can be explosive and
sulfuric acid can cause severe burns.
Batteries should be installed, serviced and replaced only by properly trained and qualified
service personnel trained in safe battery handling methods and who have the correct PPE
(Personal Protection Equipment) and tools.
The following precautions should be observed when working with the batteries:
•
•
•
•
•
•
•
•
•
•
Eye protection should be worn to prevent injury from electrical arcs.
Remove rings, watches and all other metal objects.
Use only tools with insulated handles.
Wear rubber gloves and boots.
When replacing batteries, replace them with the same type and number of batteries or battery packs.
Do not dispose of batteries in a fire. The batteries may explode.
Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It is
toxic.
Never lay metal objects of any type on top of the batteries.
Disconnect the charging source before connecting or disconnecting battery terminals.
Determine whether the battery is grounded. If the battery is grounded, remove source of
the ground. Contact with any part of a grounded battery can result in electrical shock. The
likelihood of such shock can be reduced if such grounds are removed during installation and
maintenance.
! CAUTION
Risk of explosion and fire. Can cause property damage, injury and death.
To reduce the risk of fire, connect only to a circuit provided with correct amperes maximum
branch circuit overcurrent protection (see Table 12) in accordance with the National Electric
Code, ANSI/NFPA 70.
NOTE
The maximum available fault current from the battery supply is 8500A and the DC voltage
rating of the battery supply overcurrent protective device that is to be installed near the battery
supply must be at least 600VDC.
Liebert® NX™
23
Battery Installation
4.3
External Battery Cabinet Installation
4.3.1
Battery Cabinets
Figure 9
Battery cabinets for Liebert NX
Top Cable Entry
BCB Plate and BCB
Optional Alber BDSi
Data Collection/Load
Module
Optional Alber
BDSi Controller
Module
Battery Trays
Liebert 49" Battery Cabinet
Liebert 33" Battery Cabinet
The same model battery cabinet may be installed in parallel in multiple cabinet striSngs for additional
capacity. Battery run time depends on the cabinet model, the number of cabinets and the load on the UPS.
Handling—The battery cabinet has casters to facilitate movement over short distances. The bottoms
of the battery cabinets are reinforced to permit movement by forklift over longer distances.
Inspection—Remove all panels and visually inspect the batteries, bus connections and cabinet for
any damage. Exercise caution: voltage is present within the battery cabinet even before installation.
If there are signs of damage, do not proceed. Call Liebert Services at 1-800-542-2378.
Storage—The batteries can be stored for up to six months without appreciable deterioration. If
planning to store a battery cabinet for longer than six months or at temperatures higher than 77°F
(25°C), contact Liebert Services for recommended precautions.
! CAUTION
Risk of electrical shock. Can cause injury and death.
Any battery system should be installed by properly trained and qualified personnel.
When installing an external battery cabinet that is NOT a Liebert NX battery cabinet, the customer
must provide overcurrent protection. See Table 8 for sizing of protection devices.
NOTE
When using an external battery supply that is not provided by Liebert, refer to the battery
manufacturer’s installation manual for battery installation and maintenance instructions,
available on the manufacturer’s Web site.
NOTE
When replacing batteries, Liebert recommends that the all batteries in external cabinets be the
same type. See Table 11 for a list of batteries that are approved for use with this product.
24
Liebert® NX™
Battery Installation
4.3.2
Connecting the Batteries
If the Liebert NX battery cabinets are installed on a raised floor, the battery power cables and circuit
breaker control cables may be routed to the UPS cabinet via the floor of the cabinet (bottom entry).
If the Liebert NX battery cabinets are installed adjacent to one another on a solid floor, these cables
may be passed between the cabinets through lifting slots in the lower sides of the cabinets.
Intertray connections must be made before the battery cabinet can be used.
Figure 10 Battery cabinet—details
Tray Handle
Insulated Post
for Cabling
4.3.3
Installation Considerations
Position— If the system includes a matching maintenance bypass cabinet (MBC), the MBC should
be installed first and the battery cabinet installed on the opposite side of the UPS. Otherwise, leftside placement of the battery cabinet is preferable.
The battery cabinet(s) are designed to be located conveniently next to each UPS module, and are also
available in stand-alone configurations with painted side panels. The front access design eliminates
side and rear service clearance requirements. Refer to Table 38 for battery cabinet dimensions and
weights.
Bolt-On Cabinets—Matching battery cabinets are designed to bolt onto the side of the UPS module
cabinet. Use bolts that ship with each unit to connect cabinet frames at posts, two places in the front
and two places in the rear.
Service Clearance—Allow front access to the battery cabinet at all times for maintenance and
servicing. Electrical codes require that the battery cabinet be installed with no less than 3 feet (1m) of
clearance at the front of the cabinet when operating. Side and rear panels do not require service
clearance.
Cables—Cables may be run between the cabinets through cutouts in the top of the cabinet,
eliminating the need for external conduit runs. Route cables before moving cabinets into final position
for bolting together. No top or bottom entry cables are required, except for remotely located cabinets
which require conduits.
Software—To allow the UPS to accurately display the battery run time, the number of battery
cabinets must be noted when performing initial startup and setup using the configuration software.
This is to be performed by the Liebert Services customer engineer when commissioning the unit.
Casters and Adjustable Stops—The adjustable stops are not designed to bear the full weight of the
cabinet. Lower the stops until they are finger-tight in contact with the floor. Then tighten a small
amount with a wrench (less than two turns) to give a good friction fit. When mounting the battery
cabinet on seismic stands, ensure that the casters are bearing the weight of the cabinet.
Battery Support Tray—Be sure to connect the battery tray support to the front of the cabinet
before sliding a battery tray out for connection or service. Without the support, the battery tray may
fall out of the cabinet. See Figure 11 for details.
Liebert® NX™
25
Battery Installation
Figure 11 Battery tray and supports
Slot in support
secured by screw-in
connector at corner
of battery tray...
4.3.4
... and notched end of
support slips into slot at
top corner of battery
compartment
Connecting the Battery Cabinet to the UPS
After the battery cabinet equipment has been positioned and secured for operation and the batteries
have been connected, connect the power cables as described below.
1. Verify that all incoming high and low voltage power circuits are de-energized and locked out or
tagged out before installing cables or making any electrical connections.
2. Remove the UPS front protective cover to gain access to the equipment ground busbar.
3. Connect the safety ground and any necessary bonding ground cables to the copper ground busbar.
(example: UPS located on the bottom of the equipment below the power connections).
All cabinets in the UPS system must be connected to the user's ground connection.
NOTE
The grounding bonding arrangement must be in accordance with the National Electrical Code
and all applicable local codes.
4. Connect the system battery cables. Be sure that the battery connections are made with the right
polarity, and tighten the connections to 44 lb-in. (5 N-m) (M6 Bolt). Do not close the battery circuit
breaker before the equipment has been commissioned.
5. Connect supplied auxiliary control cable to pins J10.2 and J10.3 on the U2 monitoring board (see
3.3 - Dry Contacts).
4.4
Non-Standard Batteries
When batteries other than a matching battery cabinet are used, a remote battery disconnect switch
with overcurrent protection is required per the National Electrical Code. Contact your local Emerson
sales representative about this option.
Install battery racks, cabinets and batteries in accordance with the manufacturer's instructions.
Verify that the battery area has adequate ventilation and battery operating temperature complies
with the manufacturer's specifications and with all applicable national and local codes.
If you have any questions concerning batteries, battery racks or accessories, contact Liebert Services
at 1-800-543-2378.
26
Liebert® NX™
Battery Installation
4.5
BCB Shunt Trip
The Liebert NX battery cabinet has the shunt trip installed in the circuit breaker. When a DC ground
fault (using the optional DC Ground Fault kit), a battery overtemperature or EPO is activated, the
shunt trip will open the circuit breaker.
NOTE
The Liebert NX battery Cabinet circuit breaker will not open at the end of a battery discharge.
The UPS will isolate the batteries internally in this situation.
4.6
Alber Monitoring System—Optional
The Liebert matching battery cabinet allows installing an optional Alber® battery monitoring system
in the cabinet. The Alber Battery Monitoring by Liebert continuously checks all critical battery
parameters, such as cell voltage, overall string voltage, current and temperature. Automatic periodic
tests of internal resistance of each battery will verify the battery’s operating integrity. Additional
capabilities include automatic internal DC resistance tests and trend analysis providing the ability to
analyze performance and aid in troubleshooting.
The Alber monitoring system is installed inside the battery cabinet (see Figure 9). The monitoring
system requires approximately 0.5A, single-phase 480V.
NOTE
This power must be UPS protected.
This power can come from the output terminals of the UPS, a distribution panel, or another
UPS-protected source. This power is to be field supplied. See Figure 37 for wiring location.
For details about operating the Alber system, see the Alber Monitoring System manual.
Liebert® NX™
27
Options
5.0
OPTIONS
5.1
Load Bus Synchronization
The Load Bus Synchronizer (LBS) keeps the output of two independent UPS systems or parallel UPS
systems in synchronization even when the systems are operating in different modes and even when
either or both systems are operating on batteries. When the LBS is used, one UPS system is
designated as master, the other as slave.
The LBS option is typically used with dual-corded equipment or with either the Liebert
SmartSwitch™ or Liebert Static Transfer Switch™ (STS) for single-corded equipment.
5.1.1
Performance Requirements
The LBS operates under the following conditions:
• Both master and slave are on inverter
(either system may be on inverter through the rectifier or on inverter through the batteries)
• Master on inverter and slave on bypass
• Master on bypass and slave on inverter
• Master and slave on bypass IF the bypass source is the same for both systems
5.1.2
LBS Cable and Settings
For Liebert NX™-to-Liebert NX dual bus configuration, only one optional LBS cable is required, the
built-in LBS will operate normally without an extra LBS control box or interface box. The LBS port is
X4 on the Parallel Board (M3). The Parallel Board is on the interior of the Liebert NX, above and left
of the power electronics; see Figures 30 and 33.
An optional, 9-pin LBS cable is used to connect two UPS systems through each system’s DB9 port on
its Parallel Board. For two parallel systems, the LBS cable can be mounted between any two units
belonging to different parallel systems. For information about the LBS kit or to order the optional
equipment, see your local Liebert representative.
The LBS cable is connected as illustrated in Figures 12 and 13.
Figure 12 Load Bus Synchronization cable connection in single module systems
LBS Cable
Parallel Board
X3
Parallel Board
X4
X4
X2-1 X2-2
X2-1 X2-2
X1-1 X1-2
UPS Module or
System #1
X1-1 X1-2
The parallel board is on the
interior of the Liebert NX UPS,
above and left of the power
electronics; see Figure 29.
UPS Module or
System #2
28
Liebert® NX™
Options
Figure 13 Load Bus Synchronization cable connection with multi-module systems
UPS
8
X2-1
X2-2
X1-1
X1-2
P4
X1-2
X2-1
P1
P2
P1
X1-1
X1-2
X4
P3
X2-2
P1
LBS
Cable
DBS
Cable
P4
X1-1
P3
X1-2
X2-1
Parallel Board
X3
P5
X4
P4
X2-2
P2
P1
X2-1
P4
P2
P3
X1-1
X4
P2
X4
X2-2
Parallel Board
X3
P5
Parallel Board
X3
P5
P3
Parallel Board
X3
P5
UPS
8
Parallel System I
A
Parallel System II
B
The LBS function is activated with configuration software; when the LBS takes effect, the graphic
LCD will display “LBS active.”
Liebert® NX™
29
Options
5.2
Configuring Parallel Sbasystem Operation
5.2.1
General
The Liebert NX uses intelligent and reliable decentralized technology to achieve parallel operation of
two or more modules.
The parallel system is used to:
• Increase the reliability of the system to ensure adequate power supply to the critical load connected.
• Increase serviceability and allow the execution of maintenance operations and repairs without
affecting the ordinary operating conditions of the system (depending on the redundancy level).
5.2.2
Features of Parallel System
• The controls for parallel UPS module operation are standard in the Liebert NX, and the configuration can be set up by changing the settings in configuration software.
• It is easy to install the parallel cables in a ring, providing high reliability and redundancy. And
the intelligent paralleling logic provides the user with maximum flexibility. For example, shutting down or starting up the UPS modules in the parallel system can be done in any sequence. If
an overload transfer occurs, the whole system can recover automatically from bypass mode after
the overload is cleared.
• The total load of the parallel system can be queried from each module’s liquid crystal display
screen.
Figure 14 Parallel system block diagram
Liebert NX UPS (40-200kVA)
Liebert NX Basic Paralleling Cabinet
Bypass
(Field Removable
Jumper for Dual
Input)
480V, 3W
Input
Static
Switch
AC
DC
DC
IOB1
AC
UOB
480V, 3W
Output
DC
480V DC
Battery Input
RIB = Rectifier Input
Breaker
IOB = Inverter Output
Breaker
MBB = Maintenance
Bypass Breaker
MIB = Maintenance
Isolation Breaker
LDB = Load Distribution
Breaker
DC
UPS Module 2
IOB2
UPS Module 3
IOB3
UPS Module 4
IOB4
30
Liebert® NX™
Options
Figure 15 Paralleling cabinet with input and bypass circuit breakers
480V, 3W
System Input
480V, 3W
System Output
MBB
Liebert NX UPS (40-200kVA)
MOB
Bypass
Static
Switch
AC
RIB 1
DC
DC
IOB 1
AC
DC
DC
480V DC
Battery
Input
RIB = Rectifier Input
Breaker
IOB = Inverter Output
Breaker
MBB = Maintenance
Bypass Breaker
MIB = Maintenance
Isolation Breaker
LDB = Load
Distribution
Breaker
RIB 2
UPS Module 2
IOB 2
RIB 3
UPS Module 3
IOB 3
RIB 4
UPS Module 4
IOB 4
Figure 16 Paralleling cabinet with input, bypass and distribution circuit breakers
480V, 3W
System Input
MBB
Liebert NX UPS (40-200 kVA)
MIB
Bypass
LDB 1
Static
Switch
RIB 1
AC
DC
DC
IOB 1
User Supplied
Plug-In Output
Breakers
AC
DC
LDB N
DC
480V DC
Battery Input
Liebert® NX™
RIB 2
UPS Module 2
IOB 2
RIB 3
UPS Module 3
IOB 3
RIB 4
UPS Module 4
IOB 4
31
480V, 3W
Output
480V, 3W
Output
Options
5.2.3
Operating Principles
Redundancy Paralleling
The parallel redundant system can noticeably improve system reliability. In normal condition, none of
the UPS modules work at full load. That means that even if the load is increased, the system will not
transfer to bypass. And when a UPS module shuts down due to any failure, the remaining UPS
modules can still power and protect the load. When redundancy is lost due to module failure or load
increase, the parallel system will trigger an alarm.
5.2.4
Operation Modes Summary
The parallel system also has operation modes such as normal, battery, bypass and maintenance
bypass. All UPS modules in the parallel system operate in coordination.
• Normal Mode Operation
The load is powered by the inverters of all the UPS modules in the system. If the frequency of
bypass is within the synchronous range, the inverter will be synchronized with the bypass.
Otherwise, the system will operate at nominal frequency.
• Battery Mode Operation
The batteries of all UPS modules power the load through their inverters. The system operates at
nominal frequency.
• Bypass Mode Operation
The condition to transfer to bypass mode is essentially the same as that of single module system.
The bypass of all the UPS modules powers the load.
• Maintenance Bypass Mode Operation
The sequence to transfer to maintenance bypass mode is the same as for transferring a singlemodule system. The maintenance bypass switches should be switched on as synchronously as
possible. Thus the system can be repaired without interrupting the power supply to critical load.
If ECO mode is selected, the double-conversion UPS operation is inhibited at most times for the
purpose of saving energy. In this mode of operation, not unlike UPS of line-interactive or standby
technology, the bypass is the preferred source. Only when the voltage and/or frequency of the
bypass supply is beyond pre-defined and adjustable limits is the critical AC load transferred to
the inverter.
5.3
Installing Parallel System
The basic installation procedure of parallel system is the same as that of single module system. The
following sections introduce only the installation procedures specific to the parallel system.
5.3.1
Conditions for Parallel System
• Each UPS module must have the same bypass source.
• The outputs of all UPS modules are connected altogether.
• The main inputs can be from different sources, but the phase rotation sequence of main inputs,
bypass inputs and outputs must be correct and the same.
• The parallel logic cable and load sharing cable must be connected in a ring correctly (see
Figure 17).
NOTICE
Risk of creating parallel systems with incorrect power ratings. Can cause equipment damage.
When paralleling UPS’s with different power ratings, the power rating of the larger UPS can
be no more than four times the power rating of the smaller UPS.
• 40-80kVA Liebert NX units can be installed in parallel with 80-120kVA Liebert NX units.
• 80-120kVA Liebert NX units can be installed in parallel with 160-200kVA.
• 40-80kVA Liebert NX units must not be installed in parallel with 160-200kVA Liebert NX
units.
32
Liebert® NX™
Options
5.3.2
Cabinet Installation
Parallel system composed of two or more UPS modules using parallel cabinet
The UPS modules that will form the parallel system should be placed side-by-side. Each battery
cabinet is placed next to its corresponding UPS module.
The parallel cabinet should be placed in the middle of the system.
5.3.3
Preliminary Checks
Each UPS module should have the same firmware and the same hardware version. Refer to the
instructions in 5.3.1 - Conditions for Parallel System.
5.3.4
Power Cables
Wiring of power cables is similar to that of a single module system (See 3.1 - Power Cabling). The
bypass sources of all modules should be the same, and the outputs should be connected altogether
correctly.
Power cables are field-supplied. Power cables to the UPS’s of the paralleling cabinet must be routed
through either the top or bottom entry access of the UPS.
NOTE
The system input and/or output circuit breaker is to be field-supplied. See Table 8 for current
rating.
NOTE
The length and specifications of power cables including the bypass input cables and UPS
output cables should be the same, thus the load can be shared evenly in bypass mode.
5.3.5
Parallel Control Cables
Parallel System Control Cables
Make the connections listed below on the parallel logic board (M3) inside the Liebert NX. (See
Figure 30 for the location of the parallel logic board):
Shielded and double-insulated control cables, available in lengths of up to 100 feet (30m), must be
interconnected in a ring configuration between UPS modules as shown below. The ring configuration
ensures high reliability of the control (refer to Figure 17).
Figure 17 Connecting system parallel control cables
1
Parallel Board
X3
P5
Parallel Board
X3
P5
X4
X2-2
UPS
2
X2-1
3
Parallel Board
X3
P5
X4
X2-2
4
Parallel Board
X3
P5
X4
X2-1
X2-2
X2-1
X4
X2-2
X2-1
Liebert® NX™
33
X1-1
P1
X1-2
P4
P2
P1
X1-2
P3
X1-1
P4
P2
P1
X1-2
P3
X1-1
P4
P2
P1
X1-2
P3
P3
X1-1
P4
P2
Interconnecting
Cables
Options
Auxiliary Dry Contact Cables
The external output breaker of each UPS must have Normally Open auxiliary contacts. These
contacts must be wired to connector X3 on the Parallel Logic Board (M3). See Figure 18.
:X T M IAN T
X2 2
P2
X2 1
P1
DBS
X3
485485+
Figure 18 Auxiliary dry contact cables for output breaker in multi-module system
! CAUTION
The auxiliary control wire must be installed to ensure proper operation of the system.
NOTE
For startup procedure, 11.2 - UPS Startup.
34
Liebert® NX™
Options
5.3.6
Emergency Power Off (EPO)
The external emergency stop facility is identical to that described for the single unit installation—
that an individual emergency stop button is provided for each unit.
Figure 19 Connecting EPO push button
SINGLE MODULE
Liebert NX Monitor Board
4
3
2
1
EPO_NO
+12V
+12V
EPO_NC
X2_J28
Remote EPO
(Customer-Supplied)
TWO MODULES IN PARALLEL
Liebert NX Monitor Board
EPO_NO
+12V
+12V
EPO_NC
X2_J28
Liebert NX Monitor Board
4
3
2
1
Remote EPO
(Customer-Supplied)
EPO_NO
+12V
+12V
EPO_NC
X2_J28
Field-Supplied Wiring
Liebert® NX™
U3839652
Rev. 0
35
UPS Specifications
6.0
UPS SPECIFICATIONS
These specifications describe requirements for the Liebert NX UPS.
6.1
Conformity and Standards
The UPS has been designed to conform to the following standards:
• UL Standard 1778
• CSA 22.2, No. 107.1
• FCC Part 15, Class A
• IEC 61000-4-5
• National Electrical Code (NFPA-70)
• NEMA PE-1
• ISTA_1H
The UPS shall be UL and cUL listed per UL Standard 1778.
6.2
UPS Environmental
The UPS is designed to operate under the following environmental conditions without damage or
degradation in electrical operating characteristics.
Table 6
Environmental characteristics
40kVA
Rated Power
60/80kVA
100/120kVA
Operating Temperature, UPS
32°F to 104°F (0°C to 40°C)
Optimal Operating Temperature, Battery
68°F to 86°F (20°C to 30°C)
Relative Humidity
0 to 95%, non-condensing
Accoustical Noise, dBA at 39 in. (1m)
(fans at low speed)
61
61
63
68.5
Up to 6562 ft. (2000m) above mean sea level without derating. Linearly
derated from 100% load at 6,562 ft. (2000m) to 88% load at 9843 ft. (3000m)
Altitude of Operation
Storage-Transport Temperature, UPS,
-4°F to 158°F (-25°C to 70°C)
Storage-Transport Temperature, Battery
-4°F to 86°F (-20°C to 33°C)
6.3
160/200kVA
UPS Mechanical Characteristics
Table 7
UPS mechanical characteristics
Parameter
40 kVA 60kVA 80kVA 80kVA 100kVA 120kVA 160kVA
200kVA
Dimensions, W x D x H, inches (mm)
All Units
25.5 x 39.0 x 78.7
(648 x 978 x 2000)
Units for use
with Liebert BDC
—
—
—
Units with Wiring
Cabinet Extension
—
—
—
—
—
—
25.5 x 39.0 x 78.7
(648 x 978 x 2000)
—
—
48.8 x 39.0 x 78.7
(1239 x 978 x 2000)
41.0 x 39.0 x 78.7
(1041 x 978 x 2000)
64.4 x 39.0 x 78.7
(1636 x 990 x 2000)
Weight, lb (kg)
All Units
1290 (585)
—
—
For use with Liebert BDC
—
1422 (645)
2201 (998)
Includes Wiring Cabinet Extension
—
1847 (837)
2626 (1191)
Heat Dissipation, BTU/H (kWH)
12,200 15,400 20,600 19,700
(3.6)
(4.5)
(6.0)
(5.8))
24,300
(7.1)
28,700
(8.4)
35,900
(10.5)
47,00
(13.8)
Airflow, CFM (m3/h)
620
(1050)
920
(1550)
920
(1550)
1590
(2700)
1590
(2700)
620
(1050)
620
(1050)
Cable Entry
1668
(2834)
Bottom or Top
Color
Black (ZP-7021)
Protection Grade
(with open/closed front doors)
IP 20
36
Liebert® NX™
UPS Specifications
6.4
Table 8
UPS Electrical Characteristics
UPS terminal
Input (For Single-Input Unit)
Unit
Rating
Nominal
Input
Current
Maximum
Input
Current
40
48
60
60
71
89
80
94
118
100
117
147
120
140
175
160
186
233
200
234
293
Rectifier Input (For Dual Input Unit Only)
Unit
Rating
Nominal
Input
Current
Maximum
Input
Current
40
48
60
60
71
89
80
94
118
100
117
147
120
140
175
160
186
233
200
234
293
Bypass Input (For Dual Input Units)
Maximum Recommended Lug
(Thomas & Betts Part #)
OCP
Current
OCP
Device
Rating
Bolt
Size
Compression
1-Hole
Mechanical
1-Hole;
72
106.8
141.5
176.3
210
279.5
351.5
80
110/125
150
175
225
300
350
M8
M8
M8
M8
M8
M10
M10
54140
54148
54110
54112
54174
54286
256-30695-886
ADR35
ADR35
ADR35
31015
31015
31015
31015
OCP
Current
OCP
Device
Rating
Bolt
Size
Compression
1-Hole
Mechanical
1-Hole
72
106.8
141.5
176.3
210
279.5
351.5
80
110/125
150
175
225
300
350
M8
M8
M8
M8
M8
M10
M10
54140
54148
54110
54112
54174
54286
256-30695-886
ADR35
ADR35
ADR35
31015
31015
250mcm
500mcm
Maximum Recommended Lug
(Thomas & Betts Part #)
Maximum Recommended Lug
(Thomas & Betts Part #)
Nominal
Input
Current
Maximum
Input
Current
OCP
Device
Rating
Bolt
Size
Compression
1-Hole
Mechanical
1-Hole
48
72
96
120
144
192
241
60
90
120
150
180
240
300
70
110
125
150
200
250
300
M8
M8
M8
M8
M8
M10
M10
54140
54145-TB
54155-TB
54110
54112
54286
256-30695-886
ADR35
ADR35
ADR35
ADR35
31015
31015
31015
Unit
Rating
Nominal
Output
Current
Maximum
Output
Current
OCP
Device
Rating
Bolt
Size
Compression
1-Hole
Mechanical
1-Hole
40
60
80
100
120
160
200
48
72
96
120
144
192
241
60
90
120
150
180
240
300
70
110
125
150
200
250
300
M8
M8
M8
M8
M8
M10
M10
54140
54145-TB
54155-TB
54110
54112
54174
256-30695-886
ADR35
ADR35
ADR35
ADR35
31015
31015
31015
Unit
Rating
40
60
80
100
120
160
200
Output
Liebert® NX™
Maximum Recommended Lug
(Thomas & Betts Part #)
37
UPS Specifications
Table 8
UPS terminal (continued)
Battery
Maximum
Recommended
Lug
(Thomas &
Betts Part #)
Unit
Rating
Nominal
Discharge
Current
Maximum
Discharge
Current
OCP
Device
Rating
Bolt
Size
Compression
One-Hole; 3/8"
bolt
40
60
80
100
120
160
200
82 at 480VDC
122 at 480VDC
163 at 480VDC
204 at 480VDC
244 at 480VDC
367 at 480VDC
408 at 480VDC
103 at 384VDC
155 at 384VDC
206 at 384VDC
258 at 384VDC
309 at 384VDC
412 at 384VDC
515 at 400VDC
125
175
225
300
350
450
600
M8
M8
M8
M8
M8
M10
M10
54106
54107
54152-TB
54157
54167
54115
54115
1.
2.
3.
4.
5.
Nominal (Nom) current is based on full rated output load.
Maximum (Max) current (125% of nominal) is short duration for battery recharge conditions.
UPS input and bypass cables must be run in separate conduit from output cables.
Nominal battery voltage is shown at 2.0 volts/cell per NEC 480-2.
OCPD = Overcurrent Protection Device. Recommended AC input and AC output overcurrent protection represents 125% of nominal full
load current (continuous) per NEC 215.
6. Minimum-sized grounding conductors to be per NEC 250-122. Parity-sized ground conductors are recommended. References are per
NEC 1999.
7. Wiring requirements:
a. AC Input: 3-phase, 3-wire, plus ground.
b. AC Output: 3-phase, 3-wire, plus ground.
8. All wiring is to be in accordance with national and local electric codes.
6.4.1
Input Rectifier
Table 9
Rectifier input power
Rated Power kVA
40
60
80
Rated Voltage, VAC
100
120
160
200
480
Supply
3-phase, 3-wire plus ground
Input Voltage Tolerance, VAC
(without derating)
480V Nominal +15%, -20% without derating
Overload capacity of input
current
100% Imax <I<125% Imax: 60 min
125% Imax <I<150% Imax: 10 min; >150% load, less than 200msec
Frequency, Hz
57-66
Power Factor
> 0.99 at full load; >0.98 at half load
Harmonic Current
Less than 3% at full rated UPS output load
See Table 8 for current ratings.
Table 10
Input voltage window with derating
Input Voltage Window
(L-L Voltage)
Percentage
of Nominal
Inverter Load,
Percentage
Charger Load,
Percentage
432VAC to 552VAC
90-115
100%
100%
431VAC to 384VAC
80-89
100%
30%
383VAC to 360VAC
75-79
100%
0%
359VAC to 288VAC
60-74
80%
0%
38
Liebert® NX™
UPS Specifications
Table 11
Liebert-approved replacement batteries
Battery
Manufacturer
Models
Supplied
12HX205FR
12HX300FR
Enersys
12HX330FR
12HX400RF
12HX505FR
45HR2000
24HR3000
East Penn
27HR3500
31HR4000
31HR5000
UPS12-100MR
UPS12-150MR
UPS12-210MR
C&D
UPS12-300MR
UPS12-400MR
UPS12-490MR
UPS12-540MR
6.4.2
DC Intermediate Circuit
Table 12
DC intermediate circuit
Rated Power kVA
40
Recommended number
of lead-acid batteries
60
80
100
2.4VDC *
Recommended end of discharge voltage
1.67 - 1.75 VDC
14.8
22.2
Maximum boost charge duration, min. *
29.6
37.0
44.4
59.2
74
1800
Boost-float threshold current, A *
0.1 C default
From 0 to 5 mV/deg. C/cell. Default value is 3mV/deg. C/cell.*
≤1
Ripple voltage superimposed%
* Set by configuration software and based on usage of VLRA batteries.
See Table 8 for current ratings.
Liebert® NX™
200
2.27VDC *
Recommended boost charge voltage
Temperature voltage compensation, mV/°C *
160
Total 40 battery blocks of 12VDC (240 cells of 2VDC)
will be supported by UPS
Recommended float charge voltage
Maximum recharge battery current, A *
120
39
UPS Specifications
6.4.3
Inverter Output
Table 13
Inverter output
40
Rated Power kVA
60
80
Rated voltage, VAC
100
120
160
200
144
180
480
Supply
3-phase, 3-wire plus ground
Frequency, Hz
60 (50Hz in frequency converter mode)
Rated Power, kW
36
54
72
90
108
Three-phase transient
overload, min. load
105% to 110% for 60 minutes
111% to 125% for 10 minutes
126% to 150% for 1 minute
Voltage Regulation%
±1% 3-phase RMS average for a balanced three-phase load for the combined variation
effects of input voltage, connected load, battery voltage, ambient temperature and load
power factor
±2% 3-phase RMS average for a 100% unbalanced load for the combined variation
effects of input voltage, connected load, battery voltage, ambient temperature and load
power factor
Frequency Regulation%
Nominal frequency regulation is ±0.05% in single module mode,
and+/- 0.25% in parallel mode.
Maximum rate of change
of frequency, Hz/sec
Selectable from 0.1Hz/sec to 3.0Hz/sec maximum for single unit
Fixed maximum of 0.2Hz/sec for paralleled units
See Table 8 for current ratings.
6.4.4
Bypass Input
Table 14
Bypass input
Rated Power, kVA
40
60
80
Rated voltage, VAC
Bypass overload
capacity (all ratings)
160
200
3-phase, 3-wire plus ground
Upper limit: +10%, +15% or +20%; Upper limit default: +15%
Lower limit: -10%, -20%, -30% or -40%; Lower limit default: -20%
Frequency, Hz
Input frequency tolerance%
120
480
Supply
Bypass voltage tolerance%
100
60
±2.5%, ±5%, ±10% and ±20%; default ±10%
Rated Output Current:
105% to 110%:
111% to 125%:
126% to 150%:
1000%:
Duration of Overload
60 Minutes
10 Minutes
1 Minute
100 Milliseconds
See Table 8 for current ratings.
Bypass frequency synchronization range setting should be wider than bypass frequency shift range.
40
Liebert® NX™
Liebert BDC™
LIEBERT BDC™
7.0
The Liebert BDC is designed to operate in UPS mode, bypass mode and maintenance mode. The
Liebert BDC offers either 45kVA or 90kVA capacity to match the associated Liebert NX™ frame
offerings. Each of the Liebert BDC capacities offer optional 480V and 600V internal transformers as
well as multiple output distribution selections.
Figure 20 Single input UPS with external Liebert BDC with optional internal transformer—typical
configuration
UPS AC input and AC output cables are factory-supplied when UPS and Bypass
Distribution Cabinet are bolted together
Bypass Distribution Cabinet
Isolation
Transformer
MBB
* AC Input
3W + G
SKRU
UPS Cabinet
225A
42 Poles
225A
42 Poles
225A
42 Poles
CB3
225A
BIB
Remove Jumper
for Dual Input
Configuration
CB2
42 Poles
200kVA
Only
Static Bypass
CB1
Rectifier
Inverter
CB5
MIB
Converter
Local Grounding
Electrode
2 Wire + Ground
Field-Supplied Wiring
Battery Cabinet
* External Overcurrent
Protection By Others
MBD
7.1
FPC12004
Rev. 3
Normal (UPS) Mode
While the Liebert BDC is in Normal mode (MBB open; BIB/MIB closed), the UPS is supplying the
connected load with continuous, high-quality AC power. In this mode of operation, the load is
protected by the UPS.
Liebert® NX™
41
Liebert BDC™
7.1.1
Bypass Mode
When the Liebert BDC is in Bypass mode, it provides an alternate path for power to the connected
equipment. Should the UPS need to be taken out of service for limited maintenance or repair, manual
activation of the bypass will cause an immediate transfer of the equipment from the UPS inverter to
the bypass source. In this mode, power will still be supplied to the UPS; however, the load is NOT
protected by the UPS.
7.2
Maintenance Mode
When the Liebert BDC is in Maintenance mode (MBB closed; BIB/MIB open), it provides an alternate
path for power to the connected equipment should the UPS need to be taken out of service for limited
maintenance or repair. In this mode of operation, no power is supplied to the UPS and the load is
NOT protected by the UPS.
7.3
Locating the Cabinet
This Liebert BDC may be mounted to the left of the UPS or installed as a stand-alone unit. In either
case, ensure that the unit is in a well-ventilated area and that there is clearance for access to the
switches and cable connections as required by national and local codes.
7.4
Cable Installation
7.4.1
Wiring Preparation
Be sure that the unit is not connected to any AC utility power source or UPS before installing any
wiring to this unit. This Liebert BDC should be installed by a qualified / certified electrician.
WARNING
Risk of electrical shock and arc flash. Can cause property damage, injury and death.
Read this section thoroughly before attempting to install wiring to this unit. Read and
comply with all warnings and cautions in this manual.
Removing the Cover Plates
Plates cover the input and output terminals on the front of the Liebert BDC. Remove these and keep
the screws and plates for reinstallation.
7.4.2
Power Cable Installation
Refer to Table 15 when selecting cables.
Table 15
Power cable size selection (Copper Wire Only)
Bus Type
Main Input
Terminal
Bypass Input
Single Input
Dual Input
Dual Input
Output
Liebert NX 40kVA UPS
4
4
4
3
Liebert NX 60kVA UPS
1
1
2
2
Liebert NX 80kVA UPS
2/0
2/0
1/0
1/0
Liebert NX 100kVA UPS
4/0
4/0
2/0
2/0
Liebert NX 120kVA UPS
250
250
4/0
4/0
Liebert NX 160kVA UPS
2-3/0
2-3/0
2-3/0
2-3/0
Liebert NX 200kVA UPS
2-4/0
2-4/0
2-4/0
2-4/0
Liebert NX 480V
Battery Cabinet DC Input Bus
225A
350A
600A
—
4/0AWG
400kcmi
2-350kcmil
—
NOTE
Transient and steady state earth leakage currents may occur when starting the equipment.
This should be taken into account when selecting ground current detection devices because
these will carry the earth leakage currents of both the UPS equipment and the load.
42
Liebert® NX™
Liebert BDC™
7.4.3
Input/Output Wiring
Follow the steps below to connect the input wiring:
NOTE
Input wiring must be installed using conduit if cabinet is not mounted to the immediate right
of the UPS.
1. Locate the input wiring access (top or bottom access), remove the conduit landing plate and punch
the appropriate size hole for the size conduit being used. Pull the three/four input wires through
it, allowing some slack for installation. For cabinets that are located to the immediate left of the
UPS, the access plate is on the lower right of the cabinet. Remove the access plate and verify that
the edge guarding is installed and intact.
2. Secure the conduit to the access plate of the Liebert BDC.
3. Input power cables connect to the system input circuit breaker; refer to Figure 21 and Table 34.
4. Connect the ground (earth) wire to the earth busbar and tighten it to 240lb-in. (27N-m) (M10
bolt).
5. Locate UPS input and output cables and access panel to UPS on lower right side.
NOTE
If the Liebert BDC is not to be bolted to the UPS, use either top or bottom access plate.
6. Connect the system ground cable between the Liebert BDC and UPS and tighten the connections
to 240lb-in. (27N-m) (M10 bolt).
7. Connect the system input cables between the Liebert BDC “UPS Input” Busbars (A-B-C N
terminals) and UPS input busbars (A-B-C N terminals) and tighten the connections to 240lb-in.
(27N-m) (M10 bolt).
8. Connect the system output cables between the Liebert BDC 'UPS Output' Busbars (A-B-C N
terminals) and UPS output busbars (A-B-C N terminals) and tighten the connections to 240lb-in.
(27N-m) (M10 bolt).
NOTICE
Risk of improper wiring connection. Can cause equipment damage.
The control wire must be installed to ensure proper operation of the system and fully protect
the load when switching between bypass cabinet and UPS.
Liebert® NX™
43
Liebert BDC™
Figure 21 Liebert BDC connection to UPS
NOTES
1. All Liebert-supplied cable must be repositioned prior to and while the cabinets are being placed in
their final installed location.
2. All interconnection hardware supplied by Emerson®.
3. AC connections must be made to the UPS module before attaching Liebert BDC to UPS module.
4. All cabling will be field-supplied when a Liebert BDC is configured as a stand-alone cabinet.
5. Liebert BDCs must attach to the right side only of the Liebert NX™.
6. Refer to the individual drawing of each piece of equipment for additional details.
Table 16
Control wiring for Liebert NX UPS to Liebert BDC
From
To
Liebert NX UPS
Monitor Board X1-J21
Liebert BDC Terminal Strip (TB2)
J21-3 INV_S
TB1-2
J21-4 INV_C
TB2-1
NX 480 UPS Parallel Board X3
Liebert BDC Terminal Strip (TB2)
X3-1-EXT-MAINT
TB2-3
X3-2-GND2
TB2-4
44
Liebert® NX™
Liebert® NX™
H3
H2
H1
45
X0
X3
X2
W564
W574
Isolation Transformer
Output Voltage
208/120
220/127
Table 1
Isolation
Transformer
X1
W571
Black
T2 Transformer
Tap Location
208V (Yellow)
240V (Red)
Fuse 6
1/2 Amp
600 Volt
Fuse 1
1/2 Amp
600 Volt
W563
Inverter Bus Output Switch
inhibited When
Circuit Is Closed
Red
Black
7
4
A
TB2-1
TB2-2
TB2-3
TB2-4
8
5
2
K1
3 Amp Inline Fuse
Provided With
T2 Transformer
W571
J21-INV_S
To Parallel Board X3-1-EXT-MAINT
To Parallel Board X3-2-GND2
J21-INV_C
24 VAC
To UPS Monitor Board
Terminal Block J21
See Note 1
& Table
Common Black
600V White
480V Orange
400V Blue
240V Red
208V Yellow
Transformer
W570
1
1
2
3
4
5
6
TB2
B
W565
Black
W565
W572
W573
9
6
3
W566
W567
8
7
6
5
4
3
2
1
Solenoid Key Release Unit
(Auxiliary switch shown in
position with key installed.)
Interlock key normally retained
In lock. Key removable when
Solenoid is energized.
53469
Rev. 5
Solenoid Key Release Unit
Factory-Supplied Busbar
Field-Supplied Wiring
Factory-Supplied Wiring
Wiring Legend
W572
W573
W569
W564
W568
Indicator
W569
W570
OK to Transfer W567
Push Button Switch
Liebert BDC™
Figure 22 Liebert BDC connection to Liebert NX
NOTE
Install jumper on TB1 pins 4 and 5. For startup procedure, see 11.2 - UPS Startup.
Liebert BDC™
Table 17
kVa
15
Circuit breaker schedule - Main circuit breaker
Frame Amps
Trip Amps
Model Number
Interrupting
Rating AIC
208V
250A
60A
T4S060TW-S24
100K
240V
250A
50A
T4S050TW-S24
100K
380V
250A
30A
T4S030TW-S24
35K
250A
30A
T4S030TW-S24
35K
415V
250A
30A
T4S030TW-S24
35K
480V
250A
25A
T4S025TW-S24
35K
600V
250A
20A
T4S020TW-S24
25K
208V
400A
110A
T4S110TW-S24
100K
240V
400A
100A
T4S100TW-S24
100K
250A
60A
T4S060TW-S24
35K
250A
60A
T4S060TW-S24
35K
415V
250A
60A
T4S060TW-S24
35K
480V
250A
50A
T4S050TW-S24
35K
600V
250A
40A
T4S040TW-S24
25K
208V
600A
200A
T4S200TW-S24
100K
240V
400A
175A
T4S175TW-S24
100K
380V
250A
100A
T4S100TW-S24
35K
Voltage In
400V
Vendor
ABB
380V
30
50
75
100
400V
400V
ABB
ABB
250A
100A
T4S100TW-S24
35K
415V
250A
90A
T4S090TW-S24
35K
480V
250A
80A
T4S080TW-S24
35K
600V
250A
70A
T4S070TW-S24
25K
208V
600A
300A
T5S300TW-S24
100K
240V
600A
250A
T4S250TW-S24
100K
380V
400A
150A
T4S150TW-S24
35K
400A
150A
T4S150TW-S24
35K
415V
400A
150A
T4S150TW-S24
35K
480V
250A
125A
T4S125TW-S24
35K
600V
250A
100A
T4S100TW-S24
25K
208V
250A
400A
T5S400TW-S24
100K
240V
250A
350A
T5S350TW-S24
100K
380V
250A
200A
T4S200TW-S24
35K
250A
200A
T4S200TW-S24
35K
415V
250A
200A
T4S200TW-S24
35K
480V
250A
175A
T4S175TW-S24
35K
600V
250A
125A
T4S125TW-S24
25K
208V
250A
450A
T5S450BW-S24
100K
240V
250A
400A
T5S400BW-S24
100K
250A
250A
T4S250TW-S24
35K
250A
250A
T4S250TW-S24
35K
415V
250A
225A
T4S225TW-S24
35K
480V
250A
200A
T4S200TW-S24
35K
600V
250A
175A
T4S175TW-S24
25K
400V
400V
ABB
ABB
380V
125
400V
ABB
46
Liebert® NX™
Liebert BDC™
Table 17
kVa
Circuit breaker schedule - Main circuit breaker (continued)
Frame Amps
Trip Amps
Model Number
Interrupting
Rating AIC
208V
400A
600A
T5S600BW-S24
100K
240V
250A
500A
T5S500BW-S24
100K
250A
300A
T5S300BW-S24
35K
250A
300A
T5S300BW-S24
35K
415V
250A
300A
T5S300BW-S24
35K
480V
250A
250A
T4S250TW-S24
35K
600V
250A
200A
T4S200TW-S24
25K
380V
400A
400A
T5S450BW-S24
35K
400V
400V
400A
T5S400BW-S24
35K
400A
400A
T5S400BW-S24
35K
480V
400A
350A
T5S350BW-S24
35K
600V
250A
250A
T4S250TW-S24
25K
380V
600A
450A
T5S450BW-S24
35K
400V
600V
450A
T5S400BW-S24
35K
600A
450A
T5S400BW-S24
35K
480V
400A
350A
T5S350BW-S24
35K
600V
400A
300A
T5S300BW-S24
25K
380V
600A
600A
T5S600BW-S24
35K
400V
600V
600A
T5S600BW-S24
35K
Voltage In
Vendor
380V
150
200
225
300
Table 18
400V
415V
415V
415V
ABB
ABB
ABB
ABB
600A
600A
T5S600BW-S24
35K
480V
600A
500A
T5S500BW-S24
35K
600V
400A
400A
T5S400BW-S24
25K
Main panelboard circuit breaker
kVA
Voltage In
Vendor
Type
Frame
Amps
Tri
pAmps
Model
Number
Interrupting
Rating AIC
15-300
208V
ABB
FIX MTD
225A
225A
T3N225TW
22k
15-300
208V
ABB
PLUG-IN
225A
225A
T3N225TW +
22k
Table 19
Panelboard branch circuit breaker
kVA
Voltage
In
Vendor
Type
Frame
Amps
Trip
Amps
Model
Number
Interrupting
Rating AIC
15-100
208V
SQUARE D
PLUG-IN
100A
15-100A
QO
10K
15-100
208V
SQUARE D
BOLT-IN
100A
15-100A
QOB
10K
15-100
208V
SQUARE D
PLUG-IN
100A
15-100A
QOxxVH
22K
15-100
208V
SQUARE D
BOLT-IN
100A
15-100A
QOBxxVH
22K
15-100
208V
GE
PLUG-IN
100A
15-100A
THQL
10K
15-100
208V
GE
BOLT-IN
100A
15-100A
THQB
10K
15-100
208V
GE
PLUG-IN
100A
15-100A
THHQL
22K
15-100
208V
GE
BOLT-IN
100A
15-100A
THHQB
22K
Liebert® NX™
47
Liebert BDC™
Table 20
Subfeed circuit breaker
kVA
Voltage
In
Vendor
Type
Frame
Amps
Trip
Amps
Model
Number
Interrupting
Rating AIC
15-300
208V
ABB
FIX MTD
250A
100A
T4N100TW
65K
15-300
208V
ABB
FIX MTD
250A
125A
T4N125TW
65K
15-300
208V
ABB
FIX MTD
250A
150A
T4N150TW
65K
15-300
208V
ABB
FIX MTD
250A
175A
T4N175TW
65K
15-300
208V
ABB
FIX MTD
250A
200A
T4N200TW
65K
15-300
208V
ABB
FIX MTD
250A
225A
T4N225TW
65K
15-300
208V
ABB
FIX MTD
250A
250A
T4N250TW
65K
150-300
208V
ABB
FIX MTD
400A
300A
T5N300TW
65K
150-300
208V
ABB
FIX MTD
400A
350A
T5N350TW
65K
150-300
208V
ABB
FIX MTD
400A
400A
T5N400TW
65K
Table 21
Square D I-Line panelboard circuit breaker
kVA
Voltage
In
Vendor
Type
Frame
Amps
Trip
Amps
Model
Number
Interrupting
Rating AIC
50-300
208V
SQUARE D
PLUG-IN
150A
100A
HGA36100
65K
50-300
208V
SQUARE D
PLUG-IN
150A
125A
HGA36125
65K
50-300
208V
SQUARE D
PLUG-IN
150A
150A
HGA36150
65K
50-300
208V
SQUARE D
PLUG-IN
250A
175A
JGA36175
65K
50-300
208V
SQUARE D
PLUG-IN
250A
200A
JGA36200
65K
50-300
208V
SQUARE D
PLUG-IN
250A
225A
JGA36225
65K
50-300
208V
SQUARE D
PLUG-IN
250A
250A
JGA36250
65K
225-300
208V
SQUARE D
PLUG-IN
400A
300A
LA36300
42K
225-300
208V
SQUARE D
PLUG-IN
400A
350A
LA36350
42K
225-300
208V
SQUARE D
PLUG-IN
400A
400A
LA36400
42K
48
Liebert® NX™
Liebert BDC™
7.5
Bolting Cabinets Together
NOTE
UPS wiring must be completed before the cabinets are bolted together.
1. Line up cabinets so that mounting holes are aligned.
Figure 23 Bolting a Liebert NXUPS to a Liebert BDC™
Output
Cable Plate
(See Note 4)
Air
Exhaust
39.5" (1003mm)
38.6" (980mm)
Including Hinge and
Bezel Projection
Control
Wires
Input
Wires
TOP VIEW
23.5"
(597mm)
78.7?
(2000mm)
Cable
Pass-Through
Area
RIGHT SIDE VIEW
REAR VIEW
Right Side Output
Cable Entry Area
9.5 x 6.5 (241mm x 165mm)
23.5"
(597mm)
1.2"
(30mm)
FRONT VIEW
Input Landing
10 x 5.7 (254mm x 145mm)
17"
(432mm)
36.4"
(925mm)
3.1"
(80mm)
34.0"
(864mm)
8.3" (211mm)
19.9
(504mm)
Output Cable Plate
(See Note 4)
27.7"
(702mm)
Inlet Area
For Cooling
Pedestal Location
Ø0.9" (22mm) Typical
6.0"
(152mm)
11.5"
(292mm)
FRONT
Base Footprint Shaded Area
Indicates Floor Cutout Dimensions
For Colling Air And Cable Entry/exit
BOTTOM VIEW
Notes
1. All dimensions are in inches (mm).
2. 24" (610mm) minimum clearance above unit required for air exhaust.
3. Keep cabinets within 15 degrees of vertical.
4. Output Cable Plates
Panelboard Option: Top output plates have 84 knockouts for
1/2" conduit per plate. Bottom output plates have 84 plugs
for 1/2" conduit per plate.
Output Circuit Breaker Option: Top and bottom output plates
are removable blank plates. Remove, punch to suit conduit size and reinstall.
5. Control wiring and power wiring must be run in separate conduits.
6. All wiring is to be in accordance with national and local electrical codes.
7. Depth dimensions include front and rear doors.
8. Width dimensions without side panels. Add 2.2 (56mm) when adding
both side panels.
9. Clearance of 36" (914mm) minimum is recommended at front and rear for
service access.
Full Load
Heat Output
BTU/HR (kw)
Unit
kVA
Weight
lb (kg)
75
1350 (6128)
8150 (239)
125
1650 (748)
11,500 (3.37)
FPC13600
Rev. 4
2. Using supplied hardware, bolt the cabinets together. The bolts may be inserted from either the
UPS side or from the Liebert BDC side, whichever is more convenient.
Liebert® NX™
49
Liebert BDC™
Figure 24 Outline drawing, Liebert BDC™, 47" cabinet
47" (1194mm)
R 25.3" (643mm) x
180° Door Swing°
R 25.3" (643mm) x
180° Door Swing°
Output Conduit Plates
11.9" x 15.7" (302 x 400mm)
See Note 4
Input Conduit Plates
5" x 8.5" (127 x 216mm)
36.4"
(925mm)
33.8"
(859mm)
Input Conduit Plates
5" x 8.5" (127 x 216mm)
6" (152mm)
R 25.3" (643mm) x
180° Door Swing°
Control Wiring Holes
2-1/2" (64mm)
R 25.3" (643mm) x
180° Door Swing°
FRONT
Base Footprint Shaded Area
Indicates Floor Cutout Dimensions
For Cooling Air and Cable
Entry and Exit
REAR VIEW
TOP VIEW
Including Hinge
and Bezel
Projection
39.5" (1003mm)
38.6" (980mm)
47" (1194mm)
See Note 8
79.6"
(2021mm)
FRONT VIEW
2.2"
(56mm)
39.2" (996mm)
1.3"
(33mm)
3.8"
(97mm)
RIGHT
SIDE
VIEW
Unit
kVA
Weight
lb. (kg)
Full Load
Hea Output
BTU/Hr (kw)
200
2610
(1184)
15,500
(4.54)
NOTES
1. All dimensions are in inches (mm).
2. 18" [457mm] minimum clearance above unit required for air exhaust.
3. Keep cabinets within 15 degrees of vertical.
4. Output conduit plates
Panelboard option:
Top output plates have 84 knockouts for 1/2" conduit per plate.
Bottom output plates have 84 plugs for 1/2" conduit per plate.
Output circuit breaker option:
Top and bottom output plates are removable blank plates. Remove,
punch to suit conduit size and reinstall.
5. Control wiring and power wiring must be run in separate conduits.
6. All wiring is to be in accordance with national and local electrical codes.
7. Depth dimensions include front and rear doors.
8. Width dimensions without side panels. Add 2.2 [56mm] when adding
both side panels.
Left and Right Side
Output Cable Access 9. Clearance of 36" [914mm] minimum is recommended at front and rear for
service access.
Area; (2) @ 2"x10"
(210 x 254mm)
6.6" (168mm)
1.9"
(48mm)
Input Conduit Plates
32" x 8" (812 x 204mm)
26.7"
(677mm)
AIR INLET
FOR COOLING
BOTTOM VIEW
FPC1360
Rev. 1
Output Conduit Plates
15.7" x 11.9" (400 x 302mm)
See Note 4
50
Liebert® NX™
Installation Drawings
8.0
INSTALLATION DRAWINGS
The diagrams in this section illustrate the key mechanical and electrical characteristics of the Liebert
NX UPS System cabinets.
Figure 25 Outline drawing, Liebert NX 40-120kVA
Power Cable Entry
3.7 x 22.8 (94x 580)
25.5 (648)
23.6 (600)
SIDE VIEW
FRONT
78.7
(2000)
Center
of Gravity
TOP VIEW
Display
Center
of Gravity
33.1
(842)
Detail A
FRONT
20.3
(515)
FRONT
40.9
(1040)
15.4
(390)
1.6 (40)
FRONT VIEW
20.9
(530)
BOTTOM VIEW
Outer Panel
1. All dimensions are in inches (mm).
Caster
2. Minimum clearance 36" front and 8" top
required for air exhaust.
3. Keep cabinet within 15 deg. of vertical
5.9 (150)
while handling.
to Outside
4. Top and bottom cable entry available
Frame
through removable access plates.
Remove punch to suit conduit size and replace.
5. Color: Black.
6. Unit bottom is structurally adequate for forklift
Power
handling.
Cable
7. Open door to replace air filter, washable type.
Entry
8. Side panels are removed between adjacent units
that are bolted together.
9. Leveling feet are not designed to carry the full weight of the
cabinet. Finger-tighten leveler against the floor, then tighten
with a wrench less than two turns for friction fit against floor.
Table 22
3.7 (94) Caster
To Outside Frame
1.55 (39) Leveler
to Outside Frame (See Note 9)
1.6 (41) Leveler to Outside Frame
3.5 (90) Caster
To Outside Frame
Outer Panel
DETAIL A
Weights, Liebert NX 40-120kVA
UPS Weight, lb (kg)
kVA Rating
Net
Crated
Heat
BTU/Hr
Cooling Air
CFM
40
60
80
80*
100*
120
1290 (585
1290 (585
1290 (585
1422 (645
1422 (645
1422 (645
1440 (653)
1440 (653)
1440 (653)
1572 (713)
1572 (713)
1572 (713)
11612
15204
20273
19700
23496
28196
620
620
620
920
920
920
Source: U3819203, Rev. 4
Liebert® NX™
Power Cable Entry
4.9 x 11.4 (125 x290)
38.5 (978)
39 (990)
To Display
51
1.5 (38) Cable Panel
To Outside Frame
U3819203
Rev. 4
Installation Drawings
Figure 26 Terminal details, 34" battery power pack system for Liebert NX 480V UPS
PCB
See
Detail B
Transformer for Alber
monitoring system
(optional)
Fuse input Alber
monitoring system
(optional)
Terminal Block
Aux. Contacts
TOP VIEW
Without Protecting Plates
DETAIL B
2.3 (59)
(-) Negative
Ø 0.4
(9)
1.2 (30)
1.2 (30)
30 (76)
GND
Busbar
See
Detail A
See
Detail C
(+) Positive
DETAIL C
DETAIL A
1. All dimensions are in inches [mm].
2.All cables should be routed before bolting cabinets
together.
3. For stand-alone installations, the interconnecting
cables between the battery cabinet and the UPS
must be provided by others. Optional battery
intercabinet wiring kits are available for
side-by-side line-up installations.
4. All hardware supplied with battery cabinet for
bolting cabinet to UPS. Use M6 hardware provided;
assemble as shown in detail drawings.
5. See installation, operation and maintenance
manual for additional information.
6. All external wiring is to be in accordance with
national and local electrical codes.
U3819205
Rev. 2
FRONT VIEW
Without Doors and Protecting Plate
Table 23
Battery cabinet ground
Unit Rating
Bolt Size
Torque
lb-in (N-m)
80
1/4" (M6)
44 (5)
Source: U3819205, Rev. 2
Table 24
Battery cabinet circuit breaker
Cabinet
Rating
Battery
Current
OCP Device
Rating
Bolt Size
Torque
lb-in (N-m)
80kVA
195
225
1/4" (M6)
44 (5)
Source: U3819205, Rev. 2
52
Liebert® NX™
Installation Drawings
Figure 27 Liebert NX 80-120kVA dimensions—front and left side
Table 25
UPS terminal specifications
Utility Configurations
Breaker Size, Amps
Unit Rating
Bolt Shaft
Size
Torque
lb-in (N-m)
CB1
CB2
CB3
CB4
CB5
80-120
M8
88 (10)
225
225
225
225
225
Source: U3819611, Rev. 0
Liebert® NX™
53
Installation Drawings
Figure 28 Liebert NX 160-200kVA dimensions—front and left side
39.0 (990) to Display
38.5 (978)
48.9 (1242)
61.9
(1573)
Power Cable
Entry
14 x 13 (355x330)
Low Voltage
Entry
5.1 x 3.9
(130x100)
78.7
(2000)
2.7 (68)
Front
Frame
.9 (23)
Outside
Frame
.8 (19)
Front
Frame
.4 (10)
Outside
Frame
TOP VIEW (Door Open)
DETAIL A
FRONT
5.0 (127) Typ
RIGHT SIDE
38.9 (987)
See Detail A
REAR
To Centers of Caster Brkt. Typ
1.6 (41) Outside
Frame Typ
1.6 (41) Outside
Frame Typ
3
(76)
4.1 (104)
5.7 (146) Typ
27.1 (688)
To Centers
of Caster
Brkt. Typ
1.9 (49)
Front Frame
Front
32.3 x 6.4 (820x163)
Cable Entry Panel
7.3 (186)
Outside Frame
33.1
(842)
Typ
43.7 (1111) Typ.
LEVELER SPACING
Looking Top Down
BOTTOM
(Looking Top Down)
NOTES:
1. All dimensions are in inches [mm]. Weight est. 2201 lb. (1000kg).
2. 24" [610] minimum clearance above unit required for air exhaust, and 36" [914] minimum service clearance at front of unit.
3. Keep cabinet within 15 degrees of vertical.
4. Top and bottom cable entry available through removable access plates. Remove, punch to suit conduit size and replace.
5. Control wiring and power wiring must be run in separate conduits.
6. Aluminum and copper-clad aluminum cables are not recommended.
7. All wiring is to be in accordance with national and local electrical codes.
U3819621
8. Depth dimensions include front door and rear panel.
Rev. 1
9. Width dimension includes side panels. Subtract 2.2" (56mm) when removing both side panels.
Table 26
Electrical specifications, Liebert NX 160-200kVA
Voltage
Rating, kVA
Input
Output
Heat
Rejection
BTU/hr
160
480
480
35,900
1590
200
480
480
47,000
1590
Cooling Air
CFM
Source: U3819621, Rev. 1
54
Liebert® NX™
Installation Drawings
Figure 29 Liebert NX 160-200kVA dimensions—front and left side
Ø .39
(10) Typ
DC
Bus
Ground
Bus
1
(25)
Typ
5.9
(150)
20.3
(516)
10.6
(268)
10.1
(258)
1.6
(40)
8
(203)
Typ
LOWER
FRONT
RIGHT SIDE FRONT
Output
Bypass Input Bus
Bus
(Dual Input)
See Detail A
See Detail A
Main Input Bus
See Detail A
DETAIL A
Input/Output/Bypass
Right Front Corner
Post Not Shown
Ø .39
(10) Typ
1
(25)
Typ
GROUND BUS
BOTTOM CABLE ENTRY
3.9 (100)
Access Plate Height
Rear
BOTTOM VIEW
1. All dimensions are in inches [mm].
2. 24" [610] minimum clearance above unit required
for air exhaust and 36" [914] minimum service clearance at front of unit.
3. Keep cabinet within 15 degrees of vertical.
4. Top and bottom cable entry available through removable access
plates. Remove, punch to suit conduit size and replace.
5. Control wiring and power wiring must be run in separate conduits.
6. Aluminum and copper-clad aluminum cables are not recommended.
7. All wiring is to be in accordance with national and local electrical codes.
8. Terminal connecting hardware included.
Liebert® NX™
55
1
(25)
Typ
Ø .39
(10) Typ
DC BUS
U389641
Rev. 0
Installation Drawings
Figure 30 Liebert NX 40-120kVA main components—typical unit
Parallel Board
Monitor
Board
Intellislot
Communication
Ports
Input Breaker
(CB1)
Bypass Breaker
(CB2)
Replaceable
Air Filters
Maintenance
Bypass Breaker (CB3)
Output Breaker
(CB5)
CB1
DC Bus
CB2
CB3
CB5
Output Bus
Main Input GND
Bypass
Bus
Input Bus
FRONT VIEW (Dual Input)
(door open)
56
Liebert® NX™
Installation Drawings
Figure 31 Liebert NX 160-200kVA dimensional view—front and left side
1239mm (48.8")
979mm (38.5")
2000mm
(78.7")
1000mm
(39.4")
610mm (24")
590mm 23.2"
FRONT VIEW
Liebert® NX™
57
LEFT VIEW
Installation Drawings
Figure 32 Liebert NX 160-200kVA dimensions continued—top and bottom view
1239mm (48.77")
1110mm (43.72")
972mm
(38.28")
842mm
(33.14")
355mm
(13.99")
1239mm (48.77"
A
330mm
(12.99")
BOTTOM VIEW
Front of UPS
TOP VIEW
Front of UPS
Detail A
58
Liebert® NX™
Installation Drawings
Figure 33 Liebert NX 160-200kVA main components—typical unit
Parallel Board
Monitor
Board
Intellislot
Communication
Ports
Input Breaker
(CB1)
Replaceable
Air Filters
Bypass Breaker
(CB2)
Maintenance
Bypass Breaker
(CB3)
Output Breaker
(CB5)
DC Bus
Liebert® NX™
Main Input
Bus
Bypass
Output
Input Bus Bus
59
Ground
Installation Drawings
Figure 34 Liebert NX 40-120kVA cable connections
NOTES
600
(23.6")
1. All dimensions are millimeters (in.).
2. Top and bottom cable entry available through
removable access plates. Remove, punch to
accommodate conduit size and replace.
3. Control wiring and power wiring must be run in
separate conduit. Output and input cables must
be run in separate conduit.
4. Aluminum and copper-clad aluminum cables are
not recommended.
5. All wiring is to be in accordance with national
and local electrical codes.
2000
(78.7")
20 (.79")
35
(1.38")
FRONT VIEW
(with door removed)
CB1
CB2
CB3
CB5
25.4
(1")
158.1
(6.22")
6
(.24")
DC
35
(1.38")
36 (1.42")
Output
Main
Bypass
GND
DETAIL A
60
Liebert® NX™
Installation Drawings
Figure 35 Liebert NX 160-200kVA cable connections
65mm
(2.56")
FRONT VIEW
(door removed)
A
DC Bus
224mm
(8.83")
Main Input
Bus
O 10mm
(0.394")
80mm
(3.15")
Liebert® NX™
Bypass
Input Bus
(Dual Input)
61
80mm
(3.15")
Output
Bus
DETAIL A
80mm
(3.15")
Installation Drawings
Figure 36 Outline drawing, 33" battery power pack system, single cabinet
169.5 (6.7)
896.6
(35.3)
609.3
(24)
372.7 (14.7)
26.8 (1.1)
172.1
(6.8)
474.3
575.9
(18.7)
(22.7)
322.9
(12.7)
322.9
(12.7)
779.1
(30.7)
872.2
(34.3)
Bottom
(Viewed From Below)
Max. Door Swing: 120°
Top
(Viewed From Above)
845
(33.2)
965
(38)
418.9 (16.5)
490.3
(19.3)
Center
of Gravity
Center
of Gravity
2000
(78.7)
Leveling
Feet
(See
Note #9)
683
(26.9)
Right Side
Front
(Without Door)
1. All dimensions are in millimeters (inches)
2. Minimum clearance 36" front and 8" top required for air exhaust.
3. Top and bottom cable entry available through removable access plates.
4. Keep cabinet within 15 deg. of vertical while handling.
5. Control wiring and power wiring must be run in separate conduit.
6. Aluminum and copper clad cables are not recommended.
7. All wiring is to be in accordance with national and local electrical codes.
8. Intercabinet wiring between the UPS and the external battery cabinet is
field-supplied.
9. Leveling feet are not designed to carry the full weight of the cabinet.
Finger-tight leveler against the floor, then tighten with a wrench less
than 2 turns for friction fit against floor.
10. Side panels included.
11. M10 threaded mounting holes used for seismic anchoring or floor stand.
NOTE: If floor stand is used the weight of the unit must be supported under
all casters. Mounting holes same spacing front and rear.
13. Battery-support tray connects to the front of the cabinet with the
support brackets. Without the support, the battery may fall out of the cabinet.
U3819204
62
Liebert® NX™
Installation Drawings
Figure 37 Terminal details, 33" battery power pack system, single cabinet Liebert NX
59
(2.32)
PCB
(-) Negative
Transformer
For Alber Monitoring
System (Optional)
9
(0.30)
76.2
(3)
Fused Input
for Alber Monitoring
System (Optional)
Terminal Block
Aux. Contacts
DETAIL B
B
(+) Positive
A
Top
(Without Protective Plates)
NOTES:
1. All dimensions are in millimeters (inches).
2. All cables should be routed before bolting cabinets togethe r.
3. The cables between the battery cabinet and the UPS cabinet
must be supplied by others.
4. All hardware supplied with battery cabinet for bolting cabinet
to UPS use M6 hardware provided; assemble as shown in
detail drawings.
5. All external wiring is to be in accordance with national
and local electrical codes.
U3819205
Front
(Without Doors and
Protective Plates)
Liebert® NX™
63
Installation Drawings
Figure 38 Outline drawing, 49" battery power pack system, single cabinet
974mm (38.3")
1240mm (48.8)
1997mm
(78.6")
868.7mm
(34.2")
485.3mm
(19.1")
A
481.1mm (18.94")
Cable Entry Panel
190x290mm (7.2x11.4")
typ. 2
188mm
(7.4")typ.
183mm (7.2)
Outside
Frame
271mm
(10.7")
Front Frame
323mm
(12.7") typ.
296mm (11.7")
Outside Frame
Cable Entry Panel
190x290mm (7.2x11.4")
typ. 2
Rear
482mm
(19.0") typ.
SECTION A-A
(Plan View)
98mm (3.9")
Outside Frame
509mm (20")
FrontFrame
271mm
(10.7")
Rear Frame
323mm
(12.7") typ.
138mm
(5.4") typ.
RIGHT SIDE
A
FRONT
1616mm
(63.6")
482mm
(19.0")
typ.
TOP VIEW
(Door Open)
1140mm (44.9")
typ.
841mm
(33.1")
typ.
LEVELER SPACING
64
Liebert® NX™
Installation Drawings
Figure 39 Terminal details, 49" battery power pack system
Negative
(-)
A Positive
Ground
Detail A
PCB
Positive
(+)
Transformer for Alber
Monitoring System
(Optional)
Terminal Block /
Aux Contacts
B
Top View
(without BCB Cover Plate)
Liebert® NX™
Detail B
65
Fused Input
for Alber Monitoring
System (Optional)
Installation Drawings
Figure 40 Liebert NX 160-200kVA UPS to 49" battery cabinet interconnection
C
A
C
D
A
NX 160-200KVA UPS Module
Front View
B
C
D
B
D
49" Battery Cabinet Right-Side Views
NOTES:
1. All cables must be repositioned prior to and while setting the cabinets in their installed location.
2. Refer to the individual drawing of each piece of equipment for additional details.
Run
From
To
Conductors
A
UPS Battery Terminal Block
External Battery Cabinet
Positive, Negative
B
External Battery Cabinet
Additional External
Battery Cabinet(s)
Positive, Negative
C
Battery Cabinet(s) Breaker
Control Terminal Block
UPS Monitoring Board
Battery Breaker
Auxiliary Contacts
D
UPS Ground
Battery Cabinets Ground
Ground
66
Liebert® NX™
Installation Drawings
Figure 41 Liebert NX 40-120kVA UPS to 33" battery cabinet interconnection
NOTES:
1. All cables must be repositioned prior to and while setting the cabinets in their installed location.
2. Refer to the individual drawing of each piece of equipment for additional details.
Run
From
To
Conductors
A
UPS Battery Terminal Block
First External Battery Cabinet
Positive, Negative
B
External Battery Cabinet
Additional External
Battery Cabinet(s)
Positive, Negative
C
Battery Cabinet(s) Breaker
Control Terminal Block
UPS Monitoring Board
Battery Breaker
Auxiliary Contacts
D
UPS Ground
Battery Cabinets Ground
Ground
Liebert® NX™
67
Installation Drawings
Figure 42 Outline drawing, Liebert NX 480V 33" parallel cabinet
845
(33.2)
965
(38)
2000
(78.7)
Top
Front
Right Side
NOTE:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
All dimensions are in millimeters (in).
Eight-inch minimum clearance above unit required for air exhaust.
Keep cabinet within 15 degrees of vertical while handling.
Top and bottom cable entry available through removable access plates. Remove access plate,
punch to suit conduit size and replace.
Color - black.
Unit bottom is structurally adequate for forklift handling.
M10 threaded mounting holes used for seismic anchoring or floor stand.
NOTE: If floor stand is used, the weight of the unit must be supported under all casters.
Each mounting location is supported by two 10 ga. (.135") galvanized steel. The threaded
insert is approximately 3/4" deep. Mounting holes are underneath unit base; mounting bolts
must be threaded into unit.
Side panels must be removed from adjacent units that are bolted together.
Leveling feet are not designed to carry the full weight of the cabinet. Finger-tighten leveler
against the floor, then tighten with a wrench less than 2 turns for friction fit against floor.
68
Liebert® NX™
Installation Drawings
Figure 43 Outline drawing, Liebert NX 480V 49" parallel cabinet
1240
(48.8)
965
(38)
2000
(78.7)
Top
Right Side
Front
NOTE:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
All dimensions are in millimeters (in).
Eight-inch minimum clearance above unit required for air exhaust.
Keep cabinet within 15 degrees of vertical while handling.
Top and bottom cable entry available through removable access plates. Remove access plate punch to
suit conduit size and replace.
Color - black.
Unit bottom is structurally adequate for forklift handling.
M10 threaded mounting holes used for seismic anchoring or floor stand.
NOTE: If floor stand is used, the weight of the unit must be supported under all casters.
Each mounting location is supported by two 10 ga. (.135") galvanized steel. The threaded insert is
approximately 3/4" deep. Mounting holes are underneath unit base; mounting bolts must be threaded
into unit.
Side panels must be removed from adjacent units that are bolted together.
Leveling feet are not designed to carry the full weight of the cabinet. Finger-tighten leveler against
the floor, then tighten with a wrench less than 2 turns for friction fit against floor.
Liebert® NX™
69
Installation Drawings
Figure 44 Liebert NX 480V paralleling cabinet with input and bypass circuit breakers, main components
System
Input
System Output
Tie Breaker
UPS Output
Breaker
UPS
Input
Breakers
Kirk - Key
Fuse
Disconnect
Ground
Busbar
System
Bypass
Tie Breaker
Rear
Front
70
System
Output
Busbar
Liebert® NX™
Installation Drawings
Figure 45 Liebert NX 480V paralleling cabinet main components—input, bypass and distribution circuit
breaker configuration
System Input
UPS Input
Ground
Bus
Bypass
Tie
Breaker
Front
With Covers
Front
Without Covers
Output
Distribution
Bypass
Tie
Breaker
Rear
Without Covers
Rear
With Covers
Liebert® NX™
71
UPS
Output
Installation Drawings
Figure 46 Main component location drawing Liebert NX 480V, CB2, CB3, CB4 configurations
System
Bypass
UPS
Output
Breakers
Kirk-Key
Fuse
Disconnect
Ground
Busbar
FRONT
72
System
Output
Busbars
Liebert® NX™
Installation Drawings
Figure 47 Liebert NX 480V 40-120kVA UPS to Paralleling Cabinet Interconnection—Configuration BB0,
FB0, KB0 parallel connection to Liebert NX
G1-G4
H1-H4
A
B1-B4
G1-G4
H1-H4
FRONT
Without Covers
C1-C4
B1-B4
FRONT
Door Open
C1-C4
E1-E4
F
D
REAR
Without Covers
Liebert® NX™
E1-E4
Run
From
To
Conductors
A
Utility Source
Parallel Cabinet
Ph A, B, C - System
Input
B1-B4
Parallel Cabinet
UPS #1-UPS #4 Module
AC Input
Ph A, B, C - UPS
Inputs
C1-C4
UPS #1-UPS #4
Module AC Output
Parallel Cabinet
Ph A, B, C UPS Outputs
D
Parallel Cabinet
Critical Loads
Ph A, B, C - System
Outputs
E1-E4
Parallel Cabinet
UPS #1-UPS #4
Module Gnd
Ground - UPS
F
Parallel Cabinet
Building Gnd
Ground - System
G1-G4
Parallel Cabinet
UPS #1-UPS #4 Module
Output Breaker Aux
UPS Parallel Logic
Contact
Board (M3)
H1-H4
Parallel Cabinet
UPS #1-UPS #4 Module
UPS Parallel Logic
Board (M3)
73
UPS Bypass
Detection
Installation Drawings
Figure 48 Interconnecting details for Liebert NX 40-120kVA UPS to paralleling cabinet with input, bypass
and distribution circuit breakers
A
G1-G4,
H1-H4
B1-B4
E1-E4, F
G1-G4,
H1-H4
FRONT
Without Covers
D
B1-B4
E1-E4
C1-C4
FRONT
With Door Open
C1-C4
REAR
Without Covers
Run
From
To
Conductors
A
Utility Source
Parallel Cabinet
Ph A, B, C - System Input
B1-B4
Parallel Cabinet
UPS #1-UPS #4 Module
AC Input
Ph A, B, C - UPS Inputs
C1-C4
UPS #1-UPS #4 Module
AC Output
Parallel Cabinet
Ph A, B, C - UPS Outputs
D
Parallel Cabinet
Critical Loads
Ph A, B, C - System Outputs
E1-E4
Parallel Cabinet
UPS #1-UPS #4 Module
Gnd
Ground - UPS
F
Parallel Cabinet
Building Gnd
Ground - System
G1-G4
Parallel Cabinet
UPS #1-UPS #4 Module
UPS Parallel Logic Board (M3)
Output Breaker Aux Contact
H1-H4
Parallel Cabinet
UPS #1-UPS #4 Module
UPS Parallel Logic Board (M3)
UPS Bypass Detection
74
Liebert® NX™
Installation Drawings
Figure 49 Lineup detail—Configuration CB2, CB3, CB4 parallel connection to Liebert NX
G1-G4
H1-H4
C1-C4
E1-E4
F
G1-G4
H1-H4
D
Liebert® NX™
C1-C4
B1-B4
FRONT
Without Covers
FRONT
Door Open
E1-E4
Run
From
To
Conductors
B1-B4
Utility
UPS #1-UPS #4 Module AC
Input
Ph A, B, C - UPS Inputs
C1-C4
UPS #1-UPS #4
Module AC Output
Parallel Cabinet
Ph A, B, C - UPS Outputs
D
Parallel Cabinet
Critical Loads
Ph A, B, C - System Outputs
E1-E4
Parallel Cabinet
UPS #1-UPS #4 Module Gnd
Ground - UPS
F
Parallel Cabinet
Building Gnd
Ground - System
G1-G4
Parallel Cabinet
UPS #1-UPS #4 Module
UPS Parallel Logic Board (M3)
Output Breaker Aux Contact
H1-H4
Parallel Cabinet
UPS #1-UPS #4 Module
UPS Parallel Logic Board (M3)
UPS Bypass Detection
75
Installation Drawings
Figure 50 Line-up detail, bolt together description, 40-120 kVA Liebert NX
LEFT SIDE
Without Exterior Panels
965
(38 in.)
LEFT SIDE
Isometric View
NOTES:
1. All dimensions are in millimeters (inches)
2. All cables should be routed before bolting
cabinets together.
3. The cables between the auxillary cabinets
and the UPS cabinet must be supplied by customer.
4. All hardware supplied with ancillary cabinets
for bolting cabinet to UPS.
5. Use M6 hardware provided. Assemble as
shown in detail drawing.
6. All external wiring is to be in accordance
with national and local codes.
2000
(78.7 in)
Remove
when cabinets
are to be bolted
together
DETAIL A
U3819301
A
RIGHT SIDE
Without Exterior Panels
76
Liebert® NX™
Operation
9.0
OPERATION
9.1
General Description
Liebert’s NX provides continuous, high-quality AC power to your business-critical equipment, such as
telecommunications and data processing equipment. The Liebert NX UPS supplies power that is free
of the disturbances and variations in voltage and frequency common to utility power, which is subject
to brownouts, blackouts, surges and sags.
The Liebert NX utilizes the latest in high-frequency, double-conversion pulse width modulation
technology and fully digital controls to enhance its reliability and increase the ease of use.
Specifically, the Liebert NX 480V utilizes soft-switching technology to greatly enhance efficiency.
As shown in Figure 51, the AC utility source is input at CB1 and the rectifier converts the AC utility
into DC power. The inverter converts that DC power from the utility—or DC power from the
batteries—into AC power for the load. The batteries power the load through the inverter in the event
of a power failure. The utility source can also power the load through the static bypass.
If maintenance or repair of the UPS is necessary, the load can be switched without interruption in
service to the maintenance bypass.
Figure 51 Single module block diagram (dual input configuration)
3-Phase
3W + Gnd
Internal Maintenance Bypass
3-Phase
3W + Gnd
Static Bypass
Rectifier
AC Input
Inverter
Converter
UPS Cabinet
2W + Gnd
Battery Cabinet
Liebert® NX™
77
3-Phase
3W + Gnd
AC Output
Operation
9.1.1
Bypass Supplies
The Liebert NX contains an electronically controlled switching circuit that enables the critical load to
be connected to either the inverter output or to a bypass power source via the static bypass line.
During normal system operation the load is connected to the inverter and the inverter contactor is
closed; but in the event of a UPS overload or an inverter failure, the load is automatically transferred
to the static bypass line.
To provide a clean (no-break) load transfer between the inverter output and static bypass line, the
bypass static switch activates, connecting the load to bypass. To achieve this, the inverter output and
bypass supply must be fully synchronized during normal operating conditions. This is achieved
through the inverter control electronics, which make the inverter frequency track that of the static
bypass supply, provided that the bypass remains within an acceptable frequency window.
A manually controlled, maintenance bypass supply is incorporated into the UPS design. It enables the
critical load to be powered from the utility (bypass) supply while the UPS is shut down for routine
maintenance.
NOTE
When the UPS is operating in bypass mode or on maintenance bypass, the connected
equipment is not protected from power failures or surges and sags.
9.1.2
Operating Modes
The UPS is designed to operate as an on-line, double-conversion, reverse-transfer system in the
following modes:
Normal Mode
Operating in normal mode, the Liebert NX’s rectifier derives power from a utility AC source and
supplies regulated DC power to the inverter, which regenerates precise AC power to supply the
connected equipment. The rectifier also uses the utility source power to charge the batteries.
Battery Mode
When utility AC power fails, the Liebert NX protects the critical load by instantaneously channeling
battery power to the inverter, which continues supporting the critical load without interruption.
When utility power returns and is within acceptable limits, the Liebert NX automatically shifts back
to Normal mode, with the rectifier powering the critical load.
Bypass Mode
When the Liebert NX is in bypass mode, the load is directly supported by utility power and is without
battery backup protection.
The Liebert NX’s inverter static switch and bypass static switch will shift the load from the inverter
to bypass mode without an interruption in AC power if the inverter is synchronous with the bypass
and any of the following occurs:
• inverter fails
• inverter overload capacity is exceeded
• inverter is manually turned off by the user
NOTE
If the inverter is asynchronous with the bypass, the static switch will transfer the load from the
inverter to the bypass WITH interruption in AC power to the critical load. This interruption
will be less than 10ms. This interruption time may be altered by modifying the Output transfer
interrupt time setting.
78
Liebert® NX™
Operation
Maintenance Mode
For maintenance or repair, the Liebert NX may be operated in maintenance mode. To place the
Liebert NX in maintenance mode, the load must be transferred to bypass and the inverter must be
turned off. When those conditions are met, the CB3 may be turned on and the UPS may be shut down,
permitting disconnecting the batteries for maintenance.
! WARNING
Risk of electrical shock. Can cause injury and death.
The UPS input and output must be protected with external overcurrent protection devices. In
maintenance mode, the input and output busbars remain energized.
NOTICE
Risk of improper operation. Can cause loss of power to the load and damage to the UPS.
The internal maintenance bypass must not be used when the UPS system is in a parallel
system. Doing so can cause a backfeed that can damage the UPS and interrupt power to the
load.
Parallel Redundancy Mode (System Expansion)
For higher capacity, higher reliability or both, the outputs of up to four UPS modules can be
programmed for directly paralleling while a built-in parallel controller in each UPS ensures
automatic load-sharing.
Frequency Converter Mode
The Liebert NX can be programmed into frequency converter mode for either 50Hz or 60Hz stable
output frequency. The input frequency may vary from 57Hz to 66Hz. In this mode, the static bypass
operation is disabled and the battery becomes optional, depending on any requirement to operate in
battery mode (stored energy mode).
Eco Mode
If ECO mode is selected, the double-conversion UPS operation is inhibited at most times for the
purpose of saving energy. In this mode of operation, not unlike UPS of line-interactive or stand-by
technology, the bypass is the preferred source, and only when the voltage and/or frequency of the
bypass supply is beyond pre-defined and adjustable limits is the critical AC load transferred to the
inverter. This transfer takes place with an interruption of less than 3/4 of an electrical cycle, e.g., less
than 15ms (50Hz) or less than 12.5ms (60Hz).
Liebert® NX™
79
Operator Control and Display Panel
10.0 OPERATOR CONTROL AND DISPLAY PANEL
10.1
Operator Control Panel
The control panel and LCD on the front of the Liebert NX lets the operator:
•
•
•
•
turn the UPS On or Off
transfer into the various operating modes
silence alarms
check the status of the UPS and its batteries, including all measured parameters, events and
alarms
The main areas of the control panel are shown below in Figure 52 and detailed in Figure 53.
• Mimic Display - view the status of the Liebert NX in single-line diagram format—indicators
show status by changing color when ON, flashing or OFF
• Liquid Crystal Display (LCD) and Navigation keys - view status and operational data from
the Liebert NX in tabular format
• Control buttons - turn the Liebert NX on or off, silence alarms
Figure 52 Overview of control panel
Liebert NX
80kV A-3X 3
Liquid Crystal
Display (LCD)
Main
LED1
Mimic
display
L-N current(A)
Frequency (HZ)
L-L voltage (V)
LED4
LED2
P owerFactor
LED5
2007-01-06
S ingle
L1-N/L2
71. 4
L2-N/L 3
70. 8
59. 9
59. 9
480
0.99
480
0.99
Input disconnect closed
Output disconnect closed
Bypass abnorm al
LED3
09:20:37
Norm al
Output
Bypass
59. 9
480
0. 99
EPO
INVER TER OFF
01-06 09:15
01-06 09 :15
01-06 09:15
F1
F2
F3
F4
FAULT C LEAR
SILENC E ON/ OFF
Control
buttons
INVER TER ON
?
STATUS
Navigation
keys
L3-N/L 1
71. 3
HELP
30kVA 3X3
10.1.1 Display Panel Layout
Figure 53 shows the control panel in greater detail, identifying individual items that are described in
the rest of this section.
Figure 53 Detailed view of control panel
1
2
3
4
5
6
8
9
10
11
7
12
13
14
Mimic indicators
1. Rectifier indicator
2. Battery indicator
3. Inverter indicator
4. Bypass indicator
5. Load indicator
6. Status indicator
7. Buzzer
15
16
17
18
19
Control buttons
8. Inverter Off Button
9. Emergency Power Off Button
10. EPO Cover
11. Fault Clear Button
12. Silence On/Off Button
13. Inverter On Button
14. LCD
80
Navigation keys
15. F1
16. F2
17. F3
18. F4
19. Help
Liebert® NX™
Operator Control and Display Panel
10.2
Mimic Display Indicators
The Mimic display on the front panel consists of six indicators arranged in a single-line diagram
depicting the various paths of UPS power, as shown in Figure 54.
Figure 54 Mimic display indicators location
Load indicator
Bypass indicator
Inverter indicator
Liebert NX
80kV A-3X 3
Main
LED1
Rectifier indicator
LED2
LED4
LED5
LED3
Buzzer
STATUS
09:20:37
Norm al
Bypass
L1-N/L 2
L-N current (A) 71. 4
Frequency (HZ) 59. 9
L-L voltage (V )
480
P owerFactor
Battery indicator
2007-01-06
S ingle
0. 99
Input disconnect closed
Output disconnect closed
Bypass abnorm al
Output
L 2-N/ L3
70.8
59.9
L 3-N/ L1
71.3
59.9
480
0.99
480
0. 99
EPO
INVER TER OFF
01-06 09:15
01-06 09:15
01-06 09 :15
?
Status indicator
F1
F2
F3
F4
FAULT C LEAR
SILENC E ON/ OFF
INVER TER ON
HELP
The current operational status of the Liebert NX is indicated by the color of the indicators—green,
amber or red—and whether they are ON (solid), flashing or OFF. Table 27 provides a guide to
interpreting the various states of the indicators.
Table 27
Mimic display status indicators
Indicator
(see
Figure 54)
Green
Flashing Green / Amber
Red
Off
Rectifier
Load on rectifier
Flashing Green: Utility normal,
Rectifier fault
but rectifier not operating
Battery
Battery powering
the load
Flashing Green: Battery prewarning (low battery)
Battery and converter are
Battery or battery
normal, and battery is not
converter abnormal*
discharging
Inverter
Inverter powering
the load normally
Flashing Green: Inverter on
standby
Inverter fault
Inverter normal, but off
Bypass
Load on Bypass
power
—
Bypass out of
normal range
Bypass Normal
Load
UPS output on
—
UPS output
overloaded
UPS no output power
Status
No alarms—UPS
working normally
Amber: UPS has a general
alarm
UPS has a serious
alarm
Rectifier is normal, but utility is
abnormal
—
* Battery or battery converter abnormal events include these event messages (see Appendix A): No Battery, Battery Replaced, Battery
Reverse, Batt. Conv. Over. Curr., Batt. Converter Fault, Batt. Converter Overtemp.
Liebert® NX™
81
Operator Control and Display Panel
10.3
Control Buttons
The Control Buttons on the front panel may be used to shut down the UPS completely, turn the
inverter On or Off, restart the UPS after a fault and silence the alarm, as shown in Figure 55. The
function of each button is described in Table 28.
NOTE
To activate a button properly, press and hold until you hear a short beep—about two seconds.
Figure 55 Location of control buttons
Button cover
EPO button
Liebert NX
80kV A-3X 3
Main
LED1
L-N current (A)
LED2
LED4
LED5
LED3
STATUS
09:20:37
Norm al
Bypass
L1-N/L 2
71. 4
Frequency (HZ) 59. 9
L-L voltage (V )
480
P owerFactor
0. 99
L 3-N/ L1
71.3
59.9
INVER TER OFF
01-06 09:15
01-06 09:15
01-06 09 :15
F3
F4
Fault Clear button
EPO
480
0.99
FAULT C LEAR
SILENC E ON/ OFF
?
F2
Inverter Off button
Output
L 2-N/ L3
70.8
59.9
480
0. 99
Input disconnect closed
Output disconnect closed
Bypass abnorm al
F1
Table 28
2007-01-06
S ingle
INVER TER ON
Silence On/Off button
Inverter On button
HELP
Control buttons
Button
(see Figure 55)
Function
EPO
Completely shuts down the UPS, including the static switch.
CAUTION: Use caution before pressing the Emergency Power Off (EPO) button. This button
completely shuts down the unit and cuts off power to the critical load.
Inverter Off
Press this button to shut down the inverter during operation. The load will be transferred to
static bypass.
Fault Clear
After the UPS shuts down due to a fault and the alarm condition has been resolved, press
this button to clear the fault and restart the UPS.
Silence On/Off
Press this button once to silence the alarm buzzer when an alarm is active. Any new fault will
sound the buzzer again.
If the alarm buzzer is not beeping, press this button to test the alarm sound.
Inverter On
Press this button to start the inverter and transfer from static bypass to inverter.
NOTE: If the inverter is not ready, this will not activate the UPS.
82
Liebert® NX™
Operator Control and Display Panel
10.4
Audible Buzzer
The buzzer produces three types of sounds:
• Single beep - when any control button is pressed
• Single beep repeating every two seconds - the system has a general alarm
• Continuous - the system has a serious fault
If the buzzer makes no sound, the system may be operating properly, or an alarm may have been
silenced manually.
Figure 56 Buzzer location
Liebert NX
80kV A-3X 3
LED1
LED2
LED4
2007-01-06
S ingle
Main
L-N current (A)
Frequency (HZ)
LED5
L-L voltage (V )
P owerFactor
LED3
59.9
59.9
480
0. 99
480
0. 99
L3-N/ L1
71.3
59.9
480
0.99
EPO
INVER TER OFF
01-06 09:15
01-06 09:15
01-06 09:15
F2
F3
F4
FAULT C LEAR
SILENC E ON/OFF
INVER TER ON
?
F1
10.5
L2-N/ L3
70.8
L 1-N/ L2
71.4
Input disconnect closed
Output disconnect closed
Bypass abnorm al
STATUS
Buzzer
09:20:37
Norm al
Output
Bypass
HELP
LCD Overview
The LCD on the front panel has five main sections, as shown in Figure 57. Press the F1 key below
the LCD to scroll through these sections.
• UPS System Information - view UPS name and model, date and time, overall status (see
Table 30).
• LCD Menu - choose a category of data items to appear below the menus (see Table 31).
• Data and Settings - view data items for the selected menu (see Table 31).
• Current Status Messages - check any active UPS event and alarm messages (see Appendix A).
• Navigation Key Icons - look at the icon above each navigation key to determine how the key
operates when pressed (see 10.6 - Navigation Keys).
The LCD displays alarm information in real time. After appearing in the current status section of the
LCD, status messages are stored in the history log—512 records can be stored and retrieved.
Figure 57 Sections of the LCD
Liebert NX
80kVA-3X3
LCD menu
Data and settings
Current status
messages
Main
L-N current (A)
Frequency(HZ)
L-L voltage(V)
PowerFactor
2007-01-06
Single
Bypass
L1-N/L2
71.4
59.9
480
0.99
09:20:37
Normal
Output
L2-N/L3
70.8
59.9
480
0.99
Input disconnect closed
Output disconnect closed
Bypass abnormal
L3-N/L1
71.3
59.9
480
0.99
01-06 09:15
01-06 09:15
01-06 09:15
?
F1
Liebert® NX™
F2
F3
83
UPS system
information
F4
HELP
Navigation
key icons
Operator Control and Display Panel
10.6
Navigation Keys
The navigation keys on the front panel—F1 through F4 and Help—are used to access the LCD to view
the current status and other information about the Liebert NX.
Navigation key icons on the LCD appear above each key to indicate its operation (see Table 29). The
keys are “soft keys” that can change functions according to the icon.
• Use F1 either to move to a different portion of the LCD (Shift icon) or to escape to a previous view
(ESC icon).
• Use F2 and F3 as cursor keys to move left and right or up and down, depending on the icons displayed above the keys.
• Use F4 as an Enter key to confirm a choice.
• Use HELP to access help information on the LCD.
Table 29
Icons for navigation keys
Key
Functions
Available
F1
F2
F3
Shift
Left
Right
ESC
Exit
10.7
F4
?
Enter
Up
HELP
Help
Down
UPS System Information
The UPS system information displayed at the top of the LCD is detailed in Table 30.
Table 30
Description of items in UPS system window
Item Type
Liebert NX
2007-10-12
12:30:36
080kVA-3x3
Unit #1
Single
Normal
Warning
Fault
Explanation
UPS name
Current date
Current time
080 means UPS model is 80kVA;
3x3 means 3 by 3 system (three-phase input and three-phase output)
#1 of 6 Paralleled changed to “Unit #1”
UPS is configured as a single unit system running in Normal mode
UPS in normal operation, inverter powering load, no warnings
UPS has a general alarm
UPS has a serious fault
84
Liebert® NX™
Operator Control and Display Panel
10.8
LCD Menus and Data Items
The LCD menus provide access to the following categories of information and settings for the UPS.
Selecting a menu changes the information displayed in the UPS data items portion of the LCD. The
menu choices are listed below and described in detail in Table 31.
•
•
•
•
•
•
•
•
•
•
•
•
Mains - view utility power input data: voltage, current, frequency and power factor
TX Input - view input transformer voltages
Bypass - view bypass data: voltage and frequency
Output - view output data: voltage, current, frequency and power factor
Load - view load data: load percent, output current, output power and crest factor (CF)
System - view system data
Battery - view battery characteristics—voltage, current, temperature and remaining time—and
messages when the battery is boost/float charging or disconnected
Records - access the history log—displays all records in the log (newest records added at end)
Language - select a language for LCD text (choices appear in the native language)
Settings - configure UPS settings: adjust the display contrast, choose a format for date display,
set the date and time, set up the UPS for modem communications (baud rate, address, mode and
phone numbers to dial for alarm notifications) and change the password
Command - start or stop a battery maintenance test, battery capacity test or system test
Version - view firmware versions for the inverter, rectifier and software display board and the
model information for the UPS
Figure 58 shows a menu tree of the options available from the LCD menus.
Liebert® NX™
85
Operator Control and Display Panel
Figure 58 Menu tree
Mains (input)
TX Input *
Bypass
Output
TX Output **
L-N current (A)
Frequency (Hz)
L-L voltage (V)
Power factor
L-L voltage (V)
Frequency (Hz)
L-L voltage (V)
L-N current (A)
Frequency (Hz)
L-L voltage (V)
Power factor
L-L voltage (V)
Load
System
Battery
Records
Sout (kVA)
Pout (kW)
Qout (kVAR)
Loadlevel %
Crest factor
Sout (kVA)
Pout (kW)
Qout (kVAR)
Single unit, no
parallel data
Battery voltage (V)
Battery current (A)
Battery temperature (°C)
Remain Time Min.
Battery boost charging
Battery float charging
Battery disconnected
(history log)
Language
Settings
Command
(Choices for
display)
Display contrast
Date format set
Date & time
Comm1 baud rate
Comm2 baud rate
Comm3 baud rate
Communication address
Communication mode
Callback times
Phone No.1
Phone No.2
Phone No.3
Command password
Audible Alarm
Battery maintenance test
UPS model
Battery capacity test
Monitor version
System test
Rectifier version
Stop testing
Inverter version
Freshening Charge
Stop Freshening Charge
Modem auto-answer enable
Battery Commission
* When configured, input transformer voltages are
displayed on the front LCD. When not activated, the
values are hidden.
** When configured, output transformer voltages are
displayed on the front LCD. When not activated, the
values are hidden.
Table 31
Descriptions of UPS menus and data window items
Menu Type
Mains
(input)
TX Input
Bypass
Output
TX Output
Load
Version
Item Type
Explanation
L-N current (A)
Phase current
Frequency (Hz)
Input frequency
L-L voltage (v
Line-line voltage
Power factor
Power factor
L-L voltage (V)
Line-line voltage
Frequency (Hz)
Bypass frequency
L-L voltage (A)
Line-line voltage
L-N current (A)
Phase current
Frequency (Hz)
Output frequency
L-L voltage (V)
Line-line voltage
Power factor
Power factor
L-L voltage (V)
Line-line voltage
Sout (kVA)
Sout: Apparent power
Pout (kW)
Pout: Active power
Qout (kVAR)
Qout: Reactive power
Loadlevel %
The percent of the UPS rating load
Crest factor
Output current Crest Factor
86
Liebert® NX™
Operator Control and Display Panel
Table 31
Descriptions of UPS menus and data window items (continued)
Menu Type
System
Battery
Item Type
Explanation
Sout (kVA)
Sout: Apparent power
Pout (kW)
Pout: Active power
Qout (kVAR)
Qout: Reactive power
Single unit, no parallel data
When configured as a single unit, UPS has only native load, no system load.
Battery voltage (V)
Battery bus voltage
Battery current (A)
Battery bus current
Battery temperature (°C)
Internal battery temperature °C
Remain Time Min.
Battery run time remaining.
Battery boost charging
Battery is boost charging.
Battery float charging
Battery is float charging.
Battery disconnected
Battery is not connected.
Records
(History Log)
Displays all records in the history log.
Language
(choices for text displayed)
User may select any of 12 languages for LCD text.
Display contrast
Adjust the LCD contrast
Settings
Settings
Command
(start / stop
battery &
system
tests)
Version
Liebert® NX™
Date format set
Choose the format for date display: M/D/Y, D/M/Y, M/D/Y, Y/M/D
Date & time
Set the date and time
Comm1 baud rate
Communication baud rate setting for Liebert IntelliSlot 1
Comm2 baud rate
Communication baud rate setting for Liebert IntelliSlot 2
Comm3 baud rate
Communication baud rate setting for Liebert IntelliSlot 3
Communication address
This setting is applicable to RS485 communication mode.
Communication mode
Communication Mode Setting
Callback times
When Liebert IntelliSlot 1 Communication mode is Modem, this parameter
sets the number of times a number is redialed to send an alarm notification.
Phone No.1
When Liebert IntelliSlot 1 Communication mode is Modem, this is the first
phone number to be dialed (to send an alarm notification).
Phone No.2
When Liebert IntelliSlot 1 Communication mode is Modem, this is the second
phone number to be dialed (to send an alarm notification).
Phone No.3
When Liebert IntelliSlot 1 Communication mode is Modem, this is the third
phone number to be dialed (to send an alarm notification).
Command password
User can modify the command password.
Audible Alarm
User can Enable and Disable the UPS audible alarm.
Battery maintenance test
This test performs a partial discharge of the battery to obtain a rough estimate
of the battery capacity. Load must be between 20% and 80%.
Battery capacity test
This test performs a full discharge of the battery to obtain a precise measure of
the battery capacity. Load must be between 20% and 80%.
System test
This is a self-test of the UPS. When the user activates this function, a pop-up
window appears about 5 seconds later to show the results.
Stop testing
Manually stops a battery maintenance test, battery capacity test or system
test.
Freshening Charge
Allows a temporary Equalize charge for the batteries. This charge is
configurable for 1 to 36 hours.
Stop Freshening Charge
Manually stops a Freshening Charge.
Modem Auto-answer
enable
Manually enable the modem’s auto-answer function.
Battery Commission
Resets the UPS battery detection logic after new/fresh batteries are installed.
UPS version
Provides UPS firmware version numbers for the inverter, rectifier and software
display board.
UPS model
Provides UPS model information—for example, 480V-60Hz.
87
Operator Control and Display Panel
10.9
Language Selection
The LCD menus and data display are available in 12 languages (Chinese, Dutch, English, French,
German, Italian, Japanese, Polish, Portuguese, Russian, Spanish and Swedish). To select a different
language:
• From the main menu, press the F1 (Shift) key to move the cursor to the menu at the top of the
screen.
• Press F2 and F3 (left and right arrows) as needed to select the Language menu.
• Press F1 (shift) to move the cursor to the data and settings area of the LCD.
• Use F2 and F3 (up and down) to select the required language.
• Press the F4 (enter) key to accept the language selection.
• Return to the main menu by repeatedly pressing F1 (ESC) as needed; all text on the LCD will now
be displayed in the selected language.
Figure 59 Language selection
2007-01-12
Single
Liebert NX
80KVA-3X3
Battery
POLSKI
ESPAÑOL
History
12:30:36
Normal
Language
English
DEUTSCH
FRANCAIS
ITALIANO
NEDERLANDS
SVENSKA
РУССКИЙ
Input disconnect closed
Output disconnect closed
Bypass disconnect open
PORTUGUêS
01-12 12:30
01-12 12:30
01-12 12:30
?
F1
F2
F3
F4
HELP
10.10 Current Date and Time
To change the system date and time:
• From the main menu, press the F1 (shift) key to move the cursor to the menu at the top of the
screen.
• Press F2 and F3 (left and right arrows) as needed to select the Settings menu.
• Press F1 (shift) to move the cursor to the data and settings area of the LCD.
• Use F2 and F3 (up and down) to select the Date & Time option, then press F4 (enter).
• Position the cursor on the row in which the date and time are displayed, then press F4 (enter).
• Using the F2 and F3 (up and down) keys, enter the current time and date information.
• Press F4 (enter) to save the settings, then press F1 (ESC) to return to the main menu.
88
Liebert® NX™
Operator Control and Display Panel
Figure 60 Set date and time
2007-01-12
Single
Liebert NX
80KVA-3X3
Language
12:30:36
Normal
Setting
Command
D/M/Y
Y/M/D
Y/M/D
LCD contrast
Date format
M/D/Y
Date & Time
2007-01-12
12:30:36
Input disconnect closed
Output disconnect closed
Bypass disconnect open
01-12 12:30
01-12 12:30
01-12 12:30
?
F1
Liebert® NX™
F2
F3
89
F4
HELP
Operator Control and Display Panel
10.11 UPS Status Messages
The Liebert NX displays status changes as they occur in the current status window of the LCD,
then stores that data in the history log, as shown in Figure 61.
• Current Status Window: The status messages are displayed chronologically and include the
date and time of the events. Three status messages are visible in the window at a time. To see
other messages, use the navigation keys to scroll up or down the list. A status message remains in
the current status area of the LCD until the status changes, when it is moved to the history log.
• History Log: When a record moves to the history log, the time the status changed is recorded.
The history log can hold up to 512 records. History log records may be viewed by accessing the
Records menu.
Figure 61 Current status and history log records
2007-01-12
Single
Liebert NX
80KVA-3X3
History
Battery
12:30:36
Normal
Language
Inverter in setting
2003-01-21
2003-01-21
12 :21:12
12 :21:12
2003-01-21
2003-01-22
12 :21:12
12 :30:16
2003-01-21
2003-01-21
12 :21:12
12 :30:16
UPS shutdown
History Log
(records
menu)
Bypass abnormal
Current
Status
Messages
Input disconnect closed
Output disconnect closed
Bypass disconnect open
01-12 12:30
01-12 12:30
01-12 12:30
?
F1
F2
F3
F4
HELP
See Appendix A for a complete list of status messages, along with a description and any
recommended actions.
90
Liebert® NX™
Operator Control and Display Panel
10.12 Types of LCD Screens
This section provides a quick guide to the main types of LCD screens.
10.12.1Opening Display
As the UPS begins powering up, the opening display appears, as shown in Figure 62.
Figure 62 Opening display
F1
F2
F3
HELP
F4
10.12.2Default Screen
After the UPS has powered up and completed a self-test, the output screen appears, as shown in
Figure 63. This window is the default screen.
Figure 63 Default screen
2007-01-12
Single
Liebert NX
80KVA-3X3
Main
L-N current(A)
Frequency(HZ)
L-L voltage(V)
PowerFactor
Bypass
L1-N/L2
71.4
59.9
480
0.99
12:30:36
Normal
Output
L2-N/L3
70.8
59.9
480
0.99
480
0.99
Input disconnect closed
Output disconnect closed
Bypass disconnect open
L3-N/L1
71.3
59.9
01-12 12:30
01-12 12:30
01-12 12:30
?
F1
Liebert® NX™
F2
F3
91
F4
HELP
Operator Control and Display Panel
10.12.3UPS Help Screen
Press the HELP key below the LCD to display the Help window shown in Figure 64. (Press the
HELP key again to exit the Help window.)
Figure 64 Help screen
Help information
Select the current record window
Select the previous menu item
Select the next menu item
Press ENTER key to view KVA history
Press ENTER
Q3 key to view KVA history
Q2
Q5
Q1
Press help key back to main menu
Press help key back to main menu
F1
F2
F3
F4
?
HELP
10.12.4Screen Saver Window
If there has been no interaction with the Liebert NX LCD for 2 minutes, the screen saver window
appears. It remains on the LCD for 2 minutes, then the screen will go dark. The LCD will become
active again when any key is pressed.
Figure 65 Screen saver window
2007-01-12
Single
Liebert NX
80KVA-3X3
12:30:36
Normal
Press any key back to main menu
F1
F2
F3
92
F4
F5
Liebert® NX™
Operator Control and Display Panel
10.13 Pop-Up Windows
Pop-up prompt windows appear when the user must confirm a choice or perform an operation. This
section describes the pop-up windows.
10.13.1From Bypass to Inverter Mode With Power Interruption
If the bypass voltage or frequency exceeds the synchronized range and
utility voltage or frequency is normal, the inverter cannot be in
Transfer with Interrupt,
please confirm or cancel
synchronization with the bypass, and the output can transfer to
inverter only after an interruption of about 15ms when the user
presses the INVERTER ON button. Before transferring, the system
will let the user confirm whether the interruption can be accepted, as shown at right. If the bypass
voltage returns to normal before the user makes confirmation, the UPS will transfer to inverter mode
automatically. At the same time, the prompt window will close.
10.13.2From Inverter to Bypass Mode With Interruption
If the bypass voltage or frequency exceeds the synchronized range and
the UPS is in inverter mode, the user must confirm and accept the
This operation leads to
power interruption danger before pressing the INVERTER OFF
output shutdown,
Confirm or cancel
button to shut down the output of the inverter. The user can also
cancel the shutdown operation, as shown at right. If the bypass voltage
returns to normal before the user makes the confirmation, the UPS
will transfer to bypass operation mode automatically, and at the same time the prompt window will
close disappear soon.
10.13.3System Self-Test
When a system self-test is completed, a pop-up window reports the
results of the test, as shown at right.
• Press the F4 (Enter) key and the pop-up window closes.
System Self-Test finished,
Everything is OK
10.13.4Battery Capacity Test Confirmation
When a battery capacity test is started from the Command menu, the
battery will be discharged to low-battery warning level. The Liebert
NX asks for confirmation before the test is started, as shown at right.
Battery will be depleted,
Confirm or cancel
• To confirm the choice and begin the battery capacity test, press the
F4 (Enter) key and the pop-up window disappears.
• To cancel the test, press the F1 (ESC) key. The pop-up window closes.
NOTE
For a battery capacity test to function properly, the load must be between 20% and 100%.
10.13.5Battery Self-Test Aborted, Condition Not Met
When a battery capacity test is started from the Command menu and
the battery self-test criteria are not met, the Liebert NX will not
perform a battery test. User should check whether the battery state is
boost charging and whether the load level is greater than 20 percent.
Battery Self-Test aborted,
Conditions not met
• Press the F4 (Enter) key and the pop-up window closes.
10.13.6Battery Refresh Charge Aborted, Condition Not Met
When a battery refreshening charge is started from the Command
menu and battery refreshening condition fails to meet requirements,
the Liebert NX will not perform a battery refreshening charge. User
should check if boost charging condition has not met the test criteria,
such as (No battery, charger failed, etc.).
• Press the F4 (Enter) key and the pop-up window closes.
Liebert® NX™
93
Battery Refresh Charge
aborted,
Conditions not met
Operating Instructions
11.0 OPERATING INSTRUCTIONS
11.1
Liebert NX Operating Modes
The Liebert NX can operate in any of four modes, as shown in Table 32. This section provides
instructions on switching between modes, resetting the UPS, switching the inverter On and Off and
performing other operations.
Table 32
UPS operating modes
Operating Mode
Circuit Breaker
State
Description
Normal
Operation
CB1:ON
CB2:ON
CB3:OFF
CB5:ON
The UPS is powering the load.
On Maintenance
Bypass
CB1:OFF
CB2:OFF
CB3:ON
CB5:OFF
The UPS is shut down but the load is connected to utility power via the
Maintenance Bypass Supply line.
NOTE: The load is not protected against disturbances in AC input power in
this mode.
On Test
CB1:ON
CB2:ON
CB3:ON
CB5:OFF
No load power is supplied by the UPS. The load is connected to utility power
via the Maintenance Bypass Supply line.
NOTE: The load is not protected against disturbances in AC input power in
this mode.
On Static Bypass
CB1:ON or OFF
The load power is supplied through the static bypass line. This may be
CB2:ON
considered as a temporary mode during load transfers between inverter and
CB3:OFF
maintenance bypass or supply under abnormal operating conditions.
CB5:ON
NOTE
1. The user controls and indicators mentioned in these procedures are identified in 10.0 Operator Control and Display Panel.
2. The audible alarm may sound at various points during these procedures. It can be canceled
at any time by pressing the SILENCE ON/OFF push button.
NOTE
This section refers to some modes and conditions that are set or adjusted using proprietary
service software. To take advantage of all the available features for the Liebert NX, the unit
must be commissioned by a Liebert factory-trained service engineer.
94
Liebert® NX™
Operating Instructions
11.1.1 Circuit Breakers
The UPS can be isolated by means of circuit breakers, mounted inside the cabinet and accessible after
opening the front door.
The location of the UPS power switches is shown in Figure 66.
Figure 66 Circuit breakers
The UPS unit circuit breakers are CB1, CB2, CB3 and CB5.
•
•
•
•
11.2
CB1—Main Input circuit breaker; connects the utility supply to the UPS main input.
CB2—Bypass circuit breaker; connects the utility supply to the UPS bypass.
CB3—Maintenance Bypass breaker; connects the utility supply to the UPS maintenance bypass.
CB5—Output breaker; connects inverter or bypass to the external output transformer or power
distribution panel.
UPS Startup
The Liebert NX must be fully installed and commissioned before startup, and external power isolators
must be closed. Once those general conditions are met, the UPS may be started.
11.2.1 Startup Procedure
To start the UPS from a fully powered-down condition:
1. Open the UPS door to gain access to the main input circuit breakers.
! WARNING
Risk of electrical shock. Can cause injury and death.
During this procedure the output terminals will become live. If any load equipment is
connected to the UPS output terminals, please check with the load user and ascertain
whether it is safe to apply power to the load. If the load is not ready to receive power, then
ensure that it is safely isolated from the UPS output terminals.
2. Close CB1, CB2 and CB3 (CB5 is open).
The main input contactor closes automatically and the LCD begins to show startup screens. The
Rectifier indicator flashes green while the rectifier is starting up. It stops flashing and becomes
solid green about 30 seconds after the rectifier enters the normal operation state.
Liebert® NX™
95
Operating Instructions
After initialization, the bypass SCR closes. Because the
output circuit breaker is still open, the UPS channels
power through the Maintenance Bypass Supply line
(CB3). The bypass indicator extinguishes, provided that
the bypass is normal.
The opening display is shown in the figure at right.
The UPS Mimic display indicators will be:
Indicator
State
Rectifier indicator
Green
Battery indicator
Red
Bypass indicator
Off
Inverter indicator
Off
Output indicator
Off
Status indicator
Off
F1
F2
F3
F4
HELP
• Close CB5 (CB1, CB2, CB3 and CB5 are closed).
• The Maintenance Bypass supply is now in parallel with the UPS Static Switch supply.
• Verify that the Bypass indicator is Green, then open CB3.
The UPS powers from static bypass instead of from maintenance bypass. The bypass and load
indicators turn on. The design of the hardware and software ensures uninterrupted output.
3. Close external battery circuit breaker.
After the UPS detects that the battery is connected, the red battery indicator extinguishes
moments after the battery charger starts operation.
The UPS Mimic display indicators will be
Indicator
State
Rectifier indicator
Green
Battery indicator
Off
Bypass indicator
Green
Inverter indicator
Off
Output indicator
Green
Status indicator
Amber
4. Press the INVERTER ON control button for 2 seconds.
The inverter will start and the inverter indicator will flash green. After the inverter is ready, the
UPS will transfer from bypass to inverter, the bypass indicator will turn off and the inverter and
load indicators will turn on.
The UPS is operating normally. The UPS Mimic display indicators will:
Indicator
State
Rectifier indicator
Green
Battery indicator
Off
Bypass indicator
Off
Inverter indicator
Green
Output indicator
Green
Status indicator
Green
96
Liebert® NX™
Operating Instructions
11.2.2 Verify Switching Between Operation Modes
Switch from Normal Mode to Battery Mode
• Open CB1 to enter battery mode. This breaks the utility connection to the Liebert NX.
To return to normal mode, close CB1 after a few seconds. The rectifier will restart automatically
after 10 seconds and resume feeding power to the inverter.
Switch from Normal Mode to Bypass Mode
• Press the INVERTER OFF button to switch to bypass mode.
NOTE
In bypass mode, the load is being powered by the utility and is not receiving conditioned power
through the inverter.
Switch from Bypass Mode to Normal Mode
• In bypass mode, press the INVERTER ON button. When the inverter is ready, the UPS will
switch to normal mode.
Liebert® NX™
97
Operating Instructions
11.3
Partially De-Energize the Liebert Nx 480 with Internal Maintenance Bypass
Follow the procedure below to transfer the load from the inverter output to the internal Maintenance
Bypass line of the UPS.
NOTICE
Risk of improper operation. Can cause property damage from loss of power to connected load.
Before performing this operation, read the messages on the LCD to be sure that bypass supply
is regular and the inverter is synchronous with it. If those conditions are not present, there is
a risk of a short interruption in powering the load.
This procedure assumes that the UPS is operating normally.
1. Press the INVERTER OFF button on the operator control panel for longer than 2 seconds.
The Inverter indicator will turn off and the status indicator will turn amber and an audible alarm
will sound. The load will transfer to static bypass and the inverter will shut off.
NOTE
Pressing the Alarm Silence Switch cancels the audible alarm, but leaves the warning message
displayed until the relevant condition is rectified.
2. Close maintenance breaker CB3.
The Maintenance Bypass supply is now in parallel with the UPS Static Switch supply.
3. Open output breaker CB5. This ends the bypass procedure. The load is now powered directly from
the Maintenance Bypass supply.
4. Press the EPO (Emergency Power Off) button at the UPS front panel of this UPS module only.
This will disable further Rectifier, Inverter, Static Switch and Battery operation. This will not
affect the manual maintenance bypass power switch. If a Liebert NX battery cabinet is connected,
the battery circuit breaker will shunt trip open.
5. Open the rectifier switch CB1 and bypass breaker CB2.
All operator indicators and messages will turn off as the utility-driven internal power supplies
decay. The unit will power down, but the load will continue to be supplied by the manual
Maintenance bypass.
! WARNING
Risk of electrical shock. Can cause injury and death.
Wait 5 minutes for the internal DC busbar capacitors to discharge before attempting
to remove the internal protective barriers.
! WARNING
Risk of electrical shock. Can cause injury and death.
Even with the UPS in maintenance bypass and “Off,” portions of the unit are still energized.
Service is to be performed by qualified personnel only.
NOTICE
Risk of loss of power to connected load. Can cause property damage.
The load equipment is not protected from normal supply aberrations when operating in
maintenance bypass mode.
• To return unit to normal operation, follow the steps in 11.2.1 - Startup Procedure.
98
Liebert® NX™
Operating Instructions
11.4
Partially De-Energize the Liebert Nx 480 with Bypass Distribution Cabinet (BDC)
Follow the procedure below to transfer the load from the UPS inverter output to the Maintenance
Bypass line of the UPS. To partially de-energize Liebert NX 480V UPS with Liebert BDC:
NOTICE
Risk of load being dropped by the UPS. Can cause equipment damage.
This procedure must be performed by properly trained and qualified personnel who are
knowledgeable about the operation of this system. Failure to follow these instructions will
result in loss of power and possible damage to critical equipment.
Before performing this operation, read any messages on the LCD to be sure that bypass
supply is regular and the inverter is synchronous with it. If those conditions are not present,
there is a risk of a short interruption in powering the load.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
On the Control Panel, press the INVERTER OFF button for 2 seconds.
Close the CB3 Maintenance Bypass Breaker.
Open the CB5 Output Breaker.
Manually open the external battery breaker(s).
Open the CB2 Bypass Input Breaker.
Open the CB1 Rectifier Input Breaker.
Verify that the indicator on the SKRU unit is illuminated.
Press and hold the “Alarm Present Silence” button while rotating and removing the key.
Insert the key into the lock on the MBB and turn the key.
Close the MBB.
Verify MBB is closed.
NOTICE
12.
13.
14.
15.
Risk of improper operation. Can cause property damage from loss of power to connected load.
Failure to close the MBB will interrupt power to the load. The load equipment is not protected
from normal supply aberrations when the Liebert NX is operating in the maintenance bypass
mode.
Open the MIB.
Turn the key to complete lockout of MIB.
Remove the key from lock on MIB.
Insert the key into the SKRU lock unit and turn the key.
UPS is now isolated from the critical load.
For a single-input system—The bypass isolation breaker (BIB) remains closed. This allows
power to remain present at the UPS input; refer to Figure 51.
For a single-source, dual-input system—The bypass isolation breaker (BIB) can be opened to
further isolate the UPS from input power; refer to Figure 21.
! WARNING
Risk of electrical shock and arc flash. Can cause property damage, injury and death.
Wait 5 minutes for the internal DC busbar capacitors to discharge before attempting to
remove the internal protective barriers.
! WARNING
Risk of electrical shock and arc flash. Can cause property damage, injury and death.
Even with the UPS in maintenance bypass and Off, portions of the Liebert NX system are still
energized. Service must be performed by properly trained and qualified personnel only.
NOTICE
Risk of improper operation. Can cause property damage from loss of power to connected load.
The load equipment is not protected from normal supply aberrations when the Liebert NX is
operating in the maintenance bypass mode.
Liebert® NX™
99
Operating Instructions
11.5
De-Energize the Liebert Nx 480 with Bypass Distribution Cabinet (BDC)
To de-energize the Liebert NX 480V UPS w/ BDC:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
On the Control Panel, press the INVERTER OFF button for 2 seconds.
Close CB3 Maintenance Bypass Breaker
Open CB5 Output Breaker
Manually open external battery breaker(s).
Open CB2 Bypass Input Breaker
Open CB1 Rectifier Input Breaker
Verify the indicator on the SKRU unit is illuminated
Press and hold the “Alarm Present Silence” button while rotating and removing the key.
Insert the key into the lock on the MBB and turn the key.
Close the MBB.
Verify the MBB is closed.
NOTICE
12.
13.
14.
15.
16.
11.6
Risk of improper operation. Can cause property damage from loss of power to connected load.
Failure to close the MBB will interrupt power to the load. The load equipment is not protected
from normal supply aberrations when the Liebert NX is operating in the maintenance bypass
mode.
Open the MIB
Turn the key to complete the lockout of MIB
Remove Key from MIB lock.
Insert key into the SKRU lock unit and turn the key.
UPS is now isolated from the critical load.
Open CB3 Maintenance Bypass Breaker.
Energize Nx 480 with Bypass Distribution Cabinet (BDC)
To re-energize the partially de-energized Liebert NX 480V UPS with Liebert BDC:
NOTE
UPS system must be in bypass prior to the start of any transfers. Safety features prevent
transferring the load to bypass while the Liebert NX inverter is powering the load.
1.
2.
3.
4.
5.
Verify the indicator on the SKRU unit is illuminated.
Press and hold the Alarm Present Silence button while rotating and removing the key.
Insert the key into the lock on the MIB and turn the key.
Close the MIB.
Verify that the MIB is closed.
NOTICE
Risk of power interruption. Can cause equipment damage.
Failure to close the MIB will interrupt power to the load.
6.
7.
8.
9.
Open the MBB.
Turn the key to complete locking out the MBB.
Remove the key from the MBB lock.
Insert the key into the SKRU lock unit and turn the key.
The UPS system is now available to be returned to normal operations.
10. Close the CB1 Rectifier Input Breaker.
11. Close the CB2 Bypass Input Breaker.
12. Verify that the Rectifier LED flashes green, then turns solid green after about 30 seconds.
100
Liebert® NX™
Operating Instructions
13.
14.
15.
16.
17.
18.
11.7
Close the CB5 Output Breaker.
Close the external battery breaker(s).
Verify the Battery Alarm LED extinguishes.
Open theCB3 Maintenance Bypass Breaker.
On the Control Panel, press the INVERTER ON button for 2 seconds.
Verify that the Inverter LED turns solid green, and that the unit indicates Normal Mode after
about a minute.
Auto Restart
When the main and bypass sources fail, the UPS draws power from the battery system to supply the
load until the batteries are depleted. When the UPS reaches its end of discharge (EOD) threshold, it
will shut down.
The UPS will automatically restart and enable output power:
• after utility power is restored
• if “Auto Recovery after EOD Enabling” is enabled
• after the “Auto Recovery after EOD Delay Time” expires (the default delay is 10 minutes)
During the auto recovery delay, the Liebert NX will be charging its batteries to provide a safety
margin for equipment shutdown if input power fails again.
If the “Auto Recovery after EOD Enabling” feature is disabled, the user must restart the system
manually.
11.8
Emergency Shutdown With EPO
This circuit has been designed to switch off the UPS in emergency conditions (i.e., fire, flood, etc.). The
system will turn off the rectifier and inverter and will stop powering the load immediately (including
the inverter and bypass), and the battery stops charging or discharging. If a Liebert NX battery
cabinet is connected, the circuit breaker in the battery cabinet will shunt trip open.
If input utility power is present, the UPS’s controls will remain active; however, the output will be
turned off. To remove all power from the UPS, open the external feeder breaker.
11.9
Reset After Shutdown for Emergency Stop (EPO Action) or Other Conditions
Once all appropriate measures have been taken to correct the problem indicated by the alarm
message appearing on the operator control panel display, carry out this procedure to restore the UPS
to regular operation following an EPO action or for the following reasons: Inverter Overtemperature,
Cut-off Overload, Battery Overvoltage, excessive switching (BYP: XFER COUNT BLOCK), etc.
When the user confirms that the fault is cleared:
1. Press the FAULT CLEAR button to let the system exit the emergency-off state.
NOTE
The rectifier will start again, and the bypass will begin to power the load. The Rectifier
indicator flashes while the rectifier is starting up. When the rectifier enters the normal
operation state (about 30 seconds), the rectifier indicator turns green.
2. Press the INVERTER ON button on the right side of the operator control panel for longer than
2 seconds.
NOTE
The rectifier will automatically turn on 5 minutes after the Inverter Overtemp alarm has
cleared.
Liebert® NX™
101
Operating Instructions
After the EPO button is pressed, if the input utility is removed, the UPS will shut down completely.
When input utility is returned, if the Bypass input circuit breaker (CB2) and UPS output circuit
breaker (CB5) are closed, the UPS will start up on Bypass. There will be power at the output
terminals of the UPS.
! WARNING
Risk of electrical shock. Can cause injury and death.
If the internal maintenance bypass circuit breaker (CB3) is closed and input utility is present,
there will be power at the output terminals of the UPS.
11.10 Battery Protection
11.10.1Battery Undervoltage Pre-Warning
Before the end of discharge, the Liebert NX displays a Low Battery pre-warning. After this prewarning, the battery has the capacity for 5 minutes discharging with full load (default time). The
Liebert NX can be user-configured to display this warning from 3 to 60 minutes before end-ofdischarge.
11.10.2Battery End-of-Discharge (EOD) Protection
If the battery voltage is lower than the end-of-discharge voltage, the battery converter will be shut
down.
11.11 Multi-Module System Procedures
11.11.1Isolating One Module in a Multi-Module System
1. Turn Off the inverter.
2. Open External Output CB4 in Parallel Cabinet (see Figure 67).
The UPS enters Isolation Status automatically, parallel signaling and communication become
masked and output becomes inhibited.
3. Power Off the unit for maintenance.
4. Power On the unit.
5. Unit enters Test Mode by configuration software setting.
6. Diagnosis or testing.
7. The UPS exits Test Mode by configuration software setting.
Output becomes inhibited because of Isolation Status.
8. Return all switches to the Normal position.
9. Close External Output CB4 in Parallel Cabinet (see Figure 67).
The UPS exits Isolation Status automatically, parallel signaling and communication recovers,
output becomes enabled but interlocking works now.
10. Turn On inverter and join the parallel system.
102
Liebert® NX™
Operating Instructions
Figure 67 Typical parallel system block diagram with common input supply, with separate batteries and
optional output / bypass distribution panel
480V, 3W
System Input
MBB
Liebert NX UPS (40-200 kVA)
MIB
Bypass
LDB 1
Static
Switch
RIB 1
AC
DC
DC
IOB 1
User Supplied
Plug-In Output
Breakers
AC
DC
RIB = Rectifier Input
Breaker
IOB = Inverter Output
Breaker
MBB = Maintenance
Bypass Breaker
MIB = Maintenance
Isolation Breaker
LDB = Load Distribution
Breaker
LDB N
DC
480V DC
Battery Input
RIB 2
UPS Module 2
IOB 2
RIB 3
UPS Module 3
IOB 3
RIB 4
UPS Module 4
IOB 4
NOTE
All equipment servicing procedures must be carried out only by trained personnel.
Liebert® NX™
103
480V, 3W
Output
480V, 3W
Output
Operating Instructions
11.11.2Inserting One Module into a Multi-Module System
This procedure outlines how to integrate a UPS module that has been previously isolated from other
modules of a group of paralleled UPS modules. It is assumed that the installation is complete, the
system has been commissioned by authorized personnel and the external power isolators are closed.
! WARNING
Risk of electrical shock. Can cause injury and death.
Utility power will be applied to UPS output terminals.
No operator serviceable parts are located behind covers that require a tool for their removal.
Only properly trained and qualified service personnel are authorized to remove such covers.
1. Open the UPS door to gain access to the main circuit breakers.
2. Open (or confirm disabled) maintenance bypass circuit breaker CB3.
3. Close Input breaker CB1.
The Rectifier indicator flashes on the UPS mimic panel during the startup of the rectifier and
becomes steady green once the rectifier reaches normal operation state after about 30 seconds.
4. Close external battery circuit breaker. This breaker is inside the battery cabinet or is otherwise
adjacent to the battery racks.
5. After the UPS detects the batteries, the red battery indicator extinguishes when the battery
charger starts operation.
6. Close bypass circuit breaker CB2.
7. Press the INVERTER ON control button for 2 seconds.
The inverter will start up and the inverter indicator flashes while it synchronizes to the load
voltage and frequency. After the inverter is ready, the UPS connects to the load, the inverter
indicator becomes steady green and the output indicator turns green.
8. Check that no “Warning” message is displayed in the top right corner of the LCD and that the
indicators have the status shown below.
# LED
LED Function
Status
1
Rectifier indicator
Green
2
Battery indicator
Off
3
Bypass indicator
Off
4
Inverter indicator
Green
5
Output indicator
Green
6
Alarm indicator
Off
The UPS is now operating in NORMAL mode.
104
Liebert® NX™
Operating Instructions
11.11.3Shutdown Procedure—Complete UPS and Load Shutdown
This procedure must be followed to completely power down the UPS and the load. All power switches,
isolators and circuit breakers will be opened and power will be removed from the load.
In multi-module systems, perform each step of the procedure in every UPS module before proceeding
to the next step.
NOTICE
Risk of improper operation. Can cause property damage from loss of power to connected load.
This procedure will shut off power to the load. Before beginning this procedure, shut down the
connected load to prevent the possibility of damage.
1. Press the EPO (Emergency Power Off) button at the UPS front panel only. This will disable
Rectifier, Inverter, Static Switch and Battery operation. The load will be de-energized.
! CAUTION
Except in an emergency situation, do not press any remote EPO button.
2. Open the UPS door to gain access to the main circuit breakers.
3. Open the Rectifier input circuit breaker CB1.
4. Open external battery circuit breaker. This breaker is inside the battery cabinet or is otherwise
adjacent to the battery racks.
5. Open Output circuit breaker CB5.
6. Open bypass input circuit breaker CB2.
7. Ensure maintenance bypass circuit breaker CB3 is open.
8. All mimic panel LED indications and messages will extinguish as the mains-driven, internal
power supplies decay.
9. To completely isolate the UPS from the AC supplies, the main external power input isolator (both
isolators, where dual supplies are provided for rectifier and bypass) and external output isolator
must be opened and tagged with warning labels accordingly.
11.12 Commissioning a Parallel System
! CAUTION
The operations described in this section must be performed by authorized electricians or
qualified technical personnel. If you have any difficulty, call 1-800-LIEBERT for assistance.
Check the input and output wiring of each UPS module. Ensure that the phase rotation sequence of
the main inputs and the bypass inputs and outputs of each UPS module are the same. Ensure that
the parallel cables are connected firmly.
It is assumed that the installation is complete, the system has been commissioned by authorized
personnel and the external power isolators are closed. Disconnect the load before startup.
11.13 Parallel System Startup
1. Start each UPS normally as described in 11.2 - UPS Startup.
2. Turn on the inverter of each UPS module one at a time.
3. Apply the load after the last UPS module transfers to inverter. The total load can be determined
through the LCD of either UPS.
4. Verify the load rate of each UPS module. If the load rates are roughly the same, then the parallel
system may be assumed to be operating normally.
NOTE
If one module cannot transfer to inverter mode long after its inverter is on, its output
connection may not be good or its output phase rotation may not be coincident with other
modules. At this time, the LCD for the UPS module will display “inverter asynchronous” and
the inverter indicator will flash continuously. If either UPS module makes abnormal noise
after it transfers to inverter, its parallel cables may be incorrectly connected.
Liebert® NX™
105
Options
12.0 OPTIONS
Several items of optional equipment are available for connection to the Liebert NX UPS.
12.1
Communication and Other User Terminals
The UPS can be integrated into advanced networking environments via UPS monitoring software
such as Microsoft UPS Monitor™, Liebert MultiLink™, Liebert Nform™, Liebert SiteNet™, Modbus /
Jbus, Liebert SiteScan™, Liebert SiteScan 2™, SNMP, etc. They allow UPS status monitoring and
automatic and safe shutdown of the server and PCs.
Figure 68 Monitoring board (U2) auxiliary terminal block detail
J8
J3
J1
LCD
J22
X7
J23
X6
J12
J9
J2
J15
PWR
MODEM
SNMP CARD
X5
J16
J17
Liebert IntelliSlot 2
J13 J21 J25
J28
J4
Liebert IntelliSlot 1
J26 J30 J10
X4
X4
J24
Liebert IntelliSlot 3
BFP INV ACF
X1
EPO
X2
Dry in
MBC
BCB
X3
NOTE: The black square ()
on each slot indicates Pin 1.
12.1.1 Analog Input Interface
At the X6 slot, there are two analog signal channels. Input range is from 0 to +5V, and the precision is
2 percent. “ENV-T” is used for environment temperature detecting.
•
•
•
•
X6 pin 1: Not used
X6 pin 2: +12V
X6 pin 3: ENV-T – environment temperature detection
X6 pin 4: GND
12.1.2 Power Output
The X5 slot can provide power for a modem or an external SNMP card. Available voltage is from 9V to
12V. The maximum current is 500mA.
12.1.3 Liebert IntelliSlot Communication
The Liebert NX has three Liebert IntelliSlot ports to allow field-installation of optional
communication cards. Liebert IntelliSlot cards communicate via Liebert’s proprietary ESP2 protocol
to cards that translate the information into such protocols as SNMP, IGMnet, Modbus or Jbus. Other
cards provide dry contact signals for external signaling of operating status.
The Liebert IntelliSlot communication ports may be installed or removed while the Liebert NX is
operating.
106
Liebert® NX™
Options
12.1.4 Communication and Monitoring
Liebert IntelliSlot Web Card - SNMP/HTTP Network Interface Card
This network interface card provides all real-time data and status information as SNMPv1 traps for
connection to a 10/100-baseT Ethernet connection. The same card also will transmit the same status
information and all measured parameters for display through a Web browser.
Table 33
Liebert NX communication options
Physical
description
of port
Top
Liebert
IntelliSlot
Middle
Liebert
IntelliSlot
Bottom
Liebert
IntelliSlot
Labeled
ID Name
of Port
Intellislot 2
(On Monitor
Board)
Intellislot 1
(On Monitor
Board)
Intellislot 3
(On Monitor
Board)
On the UPS
LCD screen,
under Settings,
controlled by:
Comm 1
Comm 2
Comm 3
Monitoring
Devices
supported
Baud
rate
Multiport 4
any
Relaycard-int
any
Comments
Liebert IntelliSlot
WEB-LB
2400
Not simultaneous with
Multilink in RS232-1;
See 12.1.5 - Configuring
Baud Rates
Modbus/Jbus
2400
See 12.1.5 - Configuring
Baud Rates
Multiport 4
any
Relaycard-int
any
Liebert IntelliSlot
WEB-LB
2400
See 12.1.5 - Configuring
Baud Rates
Not simultaneous with
Multilink in RS232-2
Modbus/Jbus
2400
See 12.1.5 - Configuring
Baud Rates
Multiport 4
any
Relaycard-int
any
Liebert IntelliSlot
WEB-LB
2400
See 12.1.5 - Configuring
Baud Rates
Modbus/Jbus
2400
See 12.1.5 - Configuring
Baud Rates
Top
DB9 port
RS232-1
Comm 1
MultiLink Serial
9600
Not simultaneous with Web
card in top Liebert
IntelliSlot.
Bottom
DB9 port
RS232-2
Comm 2
Service Software
(Reserved)
9600
Not simultaneous with Web
card in middle Liebert
IntelliSlot.
12.1.5 Configuring Baud Rates
The default baud rate for Liebert IntelliSlot cards is 9600. To communicate with the
Liebert OCWEB-LB, Modbus/Jbus or the adapters to permit using Liebert MultiLink, the baud rate
must be set to 2400.
To change the baud rate (refer to Table 33):
1. Use the Navigation keys directly below the LCD to highlight the Settings Screen.
2. Press F1 to move the highlight into the Data & Settings area of the LCD.
3. Use the Navigation keys to scroll down to highlight the current baud rate across from the
appropriate Comm Channel.
NOTE
The Comm Channel settings are not immediately visible because of window-size constraints.
Scroll down to view them on the screen.
4. Press the Enter (F4) key to select the Comm Channel to change.
5. Navigate to underline the desired baud rate (2400).
6. Press the Enter (F4) key to lock in the new baud rate.
Liebert® NX™
107
Options
Figure 69 Liebert IntelliSlot™ Web card display
Relay Card
The relay card provides voltage-free contact closures for remote monitoring of alarm conditions.
Delivering On Battery, On Bypass, Low Battery, Summary Alarm, UPS Fault and On UPS
signals, the easy-to-install card integrates with AS/400 computers (additional cable required) and
other relay contact monitoring systems.
The relay card is rated for 24 VAC/DC at 1A and supported in any of the three Liebert IntelliSlot bays
on the Liebert NX™.Refer to the Liebert Intellislot Relay Card user manual, SL-23211, for pin and
jumper configuration. The manual is available at Liebert’s Web site: www.liebert.com
108
Liebert® NX™
Options
MultiPort 4 Card
The MultiPort 4 card provides four sets of voltage-free contact closures for remote monitoring of
alarm conditions UPS operation On Battery and Low Battery condition. A typical application is to
allow a maximum of four computer systems to simultaneously monitor the status (e.g., utility power
failure-low battery) of a single UPS.
This card is supported in any of the three Liebert IntelliSlot® bays on the Liebert NX™.
Figure 70 MultiPort 4 card pin assignment
CPU
Pin
CPU
UPS
CPU
Assignment
Description
1
Low Battery
2
Not Used
3
Not Used
4
Not Used
5
Not Used
6
Not Used
7
Low Battery Common
8
Utility Fail Common
9
Utility Fail
CPU
12.2
LBS Mode—Load Bus Synchronization
The function of LBS is to keep the output of two independent UPS systems (single unit or multiple
unit) in synchronization even when the two systems are operating in different modes (bypass/
inverter) or on batteries. It is usually used with a Static Transfer Switch connected to the critical load
to achieve dual bus configuration.
NOTE
In LBS configuration, both units must be supplied from the same utility source.
12.2.1 Remote Alarm Monitor
Status and alarm conditions are available on an optional remote alarm monitor (RAM) panel, which is
driven by volt-free alarm status contacts (from an optional relay alarm board).
12.3
Replacing Dust Filters
1. Open the UPS door.
2. The dust filters are behind the door. For each filter, there is a bracket on either side holding the
dust filter in place, as shown in Figure 71.
3. Remove one bracket and loosen the other. The second bracket need not be removed.
4. Remove the old filter and replace with the new filter.
5. Reinstall the bracket that was removed and tighten the other bracket.
Figure 71 Dust filter replacement
Bracket
Sems screw
Liebert® NX™
Bracket
109
Specifications and Technical Data
13.0 SPECIFICATIONS AND TECHNICAL DATA
13.1
Lug Size and Torque Requirements
Use commercially available solderless lugs for the wire size required for your application. Refer to
Table 34. Connect wire to the lug using tools and procedures specified by the lug manufacturer.
Table 34
Torque specifications
Nut and Bolt CombinationS
Grade 2 Standard
Electrical Connections
with Belleville Washers
Bolt Shaft Size
Lb-in
N-m
Lb-in
N-m
1/4
5/16
3/8
1/2
53
107
192
428
6.0
12
22
22
46
60
95
256
5.2
6.8
11
29
Circuit Breakers With Compression Lugs (For Power Wiring)
Wire Size or Range
Lb-in
#6 - #4
#3 - #1
1/0 - 2/0
3/0 - 200 MCM
250 - 400 MCM
500 - 700 MCM
100
125
150
200
250
300
Circuit Breakers With Compression Lugs (For Power Wiring)
Current Rating
Lb-in
400 - 1200 Amps
300.00
Terminal Block Compression Lugs (For Control Wiring)
AWG Wire Size or Range
Lb-in
#22 -#14
3.5 to 5.3
N-m
11
14
17
23
28
34
N-m
34.00
N-m
0.4 to 0.6
NOTE: Use the values in this table unless the equipment is labeled with a different torque value.
Table 35
Battery torque rating
Battery
Initial Torque
in-lb (N-m)
UPS12-100MR
40 (4.5)
UPS12-150MR
25 (2.8)
UPS12-210MR
25 (2.8)
UPS12-300MR
110 (12.4)
UPS12-350MR
110 (12.4)
UPS12-400MR
110 (12.4)
UPS12-490MRLP
110 (12.4)
UPS12-540MR
110 (12.4)
HX300
60 (6.8)
HX330
60 (6.8)
HX400
60 (6.8)
HX500
60 (6.8)
HX540
60 (6.8)
110
Liebert® NX™
Specifications and Technical Data
13.2
Cable Lengths: Floor to Connection Point Inside UPS
To help calculate the total cable length required, refer to Table 36 for the distance from the floor to
selected connection points inside the Liebert NX. Determine the cable length required to reach the
Liebert NX, then add the appropriate length from the table and adequate slack for repair and
maintenance.
Table 36
Distance to connection points on the Liebert NX UPS
Distance
From Floor
in. (mm)
From Top of Unit
in. (mm)
Bypass AC input supply
13 (330)
66 (1676)
UPS output AC
13 (330)
66 (1676)
Battery power
13 (330)
66 (1676)
Auxiliary cables: Monitor board (U2)
67 (1702)
11 (279)
Liebert IntelliSlot Communications
60 (1524)
19 (483)
Ground
13 (330)
66 (1676)
Parallel Board
70 (1780)
11 (279)
Connection Point on UPS
Table 37
System
Size
Parallel system current table
Type
E
1+1
E1
E2
E
2+1
E1
E2
E
3+1
E1
E2
kVA
System I/P
Voltage
(VAC)
System Max
Input Current
System
Input OCPCB
Size (A)
O/P Voltage
(VAC)
Nominal
O/P Current
Rating (A)
Output
OCPCB
Size (A)
80
480V
135.0
200
480V
96.2
125
120
480V
202.5
300
480V
144.3
200
80
480V
135.0
200
480V
96.2
125
120
480V
202.5
300
480V
144.3
200
80
N/A
N/A
N/A
480V
96.2
125
120
N/A
N/A
N/A
480V
144.3
200
80
480V
270.0
350
480V
192.5
250
120
480V
405.0
600
480V
288.7
400
80
480V
270.0
350
480V
192.5
250
120
480V
405.0
600
480V
288.7
400
80
N/A
N/A
N/A
480V
192.5
250
120
N/A
N/A
N/A
480V
288.7
400
80
480V
405.0
600
480V
288.7
400
120
480V
607.5
800
480V
433.0
600
80
480V
405.0
600
480V
288.7
400
120
480V
607.5
800
480V
433.0
600
80
N/A
N/A
N/A
480V
288.7
400
120
N/A
N/A
N/A
480V
433.0
600
Type E: BB0, FB0 and KB0 configurations
Type E1: CB1, GB1, LB1 configurations;
Type E2: CB2, CB3, CB4 configurations
Use wiring rated at 75°C or greater.
Liebert® NX™
111
Specifications and Technical Data
Table 38
External cabinet dimensions, including side panels
Wide Parallel Cabinet
Unit
Width
Depth
Height
mm (inch)
1240 (48.8)
965 (38)
2000 (78.7)
Narrow Parallel Cabinet
Unit
Width
Depth
Height
mm (inch)
845 (33.2)
965 (38)
2000 (78.7)
33 in. Battery Cabinet
13.3
Unit
Width
Depth
Height
mm (inch)
845 (33.2)
965 (38)
2000 (78.7)
Cable size and tightening torques
Table 39
Cable size tightening torque at Liebert NX 40kVA UPS terminals
Cable Size
(Copper Wire Only)
Torque to Tighten
Terminal Bus & Lug Body
Main Input
(Single Input)
4
10 N-m
Main Input
(Dual Input)
4
10 N-m
Bypass Input
(Dual Input)
4
10 N-m
Output
3
10 N-m
Bus Type
Table 40
Cable size tightening torque at Liebert NX 60kVA UPS terminals
Cable Size
(Copper Wire Only)
Torque to Tighten
Terminal Bus & Lug Body
Main Input
(Single Input)
1
10 N-m
Main Input
(Dual Input)
1
10 N-m
Bypass Input
(Dual Input)
2
10 N-m
Output
2
10 N-m
Bus Type
Table 41
Cable size tightening torque at Liebert NX 80kVA UPS terminals
Cable Size
(Copper Wire Only)
Torque to Tighten
Terminal Bus & Lug Body
Main Input
(Single Input)
2/0
10 N-m
Main Input
(Dual Input)
2/0
10 N-m
Bypass Input
(Dual Input)
1/0
10 N-m
Output
1/0
10 N-m
Bus Type
112
Liebert® NX™
Specifications and Technical Data
Table 42
Cable size tightening torque at Liebert NX 100kVA UPS terminals
Cable Size
(Copper Wire Only)
Torque to Tighten
Terminal Bus & Lug Body
Main Input
(Single Input)
4/0
10 N-m
Main Input
(Dual Input)
4/0
10 N-m
Bypass Input
(Dual Input)
2/0
10 N-m
Output
2/0
10 N-m
Bus Type
Table 43
Cable size tightening torque at Liebert NX 120kVA UPS terminals
Cable Size
(Copper Wire Only)
Torque to Tighten
Terminal Bus & Lug Body
Main Input
(Single Input)
250
10 N-m
Main Input
(Dual Input)
250
10 N-m
Bypass Input
(Dual Input)
4/0
10 N-m
Output
4/0
10 N-m
Bus Type
Table 44
Cable size tightening torque at Liebert NX 160kVA UPS terminals
Cable Size
(Copper Wire Only)
Torque to Tighten
Terminal Bus & Lug Body
Main Input
(Single Input)
2-3/0
26 N-m
Main Input
(Dual Input)
2-3/0
26 N-m
Bypass Input
(Dual Input)
2-3/0
26 N-m
Output
2-3/0
26 N-m
Bus Type
Table 45
Cable size tightening torque at Liebert NX 200kVA UPS terminals
Cable Size
(Copper Wire Only)
Torque to Tighten
Terminal Bus & Lug Body
Main Input
(Single Input)
2-4/0
26 N-m
Main Input
(Dual Input)
2-4/0
26 N-m
Bypass Input
(Dual Input)
2-4/0
26 N-m
Output
2-4/0
26 N-m
Bus Type
Table 46
Cabinet
Rating
Cable size tightening torque at Liebert NX 480V Battery Cabinet DC input bus terminals
Cable Size
(Copper Wire Only)
Torque to Tighten
Terminal Bus and Lug Body
225A
4/0AWG
15 N-m
350A
400kcmil
15 N-m
600A
2-350kcmil
26 N-m
All control wiring and power wiring must be 600V rated wire.
Liebert® NX™
113
Specifications and Technical Data
13.4
Battery Run Times
Table 47
Enersys battery run times in minutes
Softscale Range
Scalable to 80kVA
External Battery Cabinet
Rated Output, kVA
Type
Quantity
40
60
HX205FR
1
19
HX300FR
1
31
HX330FR
1
HX400RF
1
HX500FR
HX205FR
HX300FR
Scalable to 120kVA
Scalable to 200kVA
Rated Output, kVA
Rated Output, kVA
80
80
100
120
160
200
11
7
N/A
N/A
N/A
N/A
N/A
17
12
12
8
6
N/A
N/A
36
22
15
15
11
8
5
N/A
40
26
18
18
13
10
6
N/A
1
64
38
27
27
20
16
10
7
2
41
27
19
N/A
N/A
N/A
N/A
N/A
2
70
41
32
32
22
18
12
9
HX330FR
2
90
52
37
37
28
23
16
11
HX400RF
2
98
62
41
41
34
27
19
14
HX500FR
2
146
93
66
66
49
38
28
21
HX205FR
3
70
41
33
N/A
N/A
N/A
N/A
N/A
HX300FR
3
109
71
50
51
38
32
21
16
HX330FR
3
146
92
63
63
47
38
27
20
HX400RF
3
156
100
72
72
54
41
32
23
HX500FR
3
224
148
105
106
80
67
46
35
HX205FR
4
97
63
45
N/A
N/A
N/A
N/A
N/A
HX300FR
4
153
99
71
72
54
41
33
23
HX330FR
4
202
131
93
94
69
53
38
30
HX400RF
4
216
142
101
102
77
64
41
35
HX500FR
4
317
206
149
150
113
95
68
50
114
Liebert® NX™
Specifications and Technical Data
Table 48
C&D Dynasty battery run times in minutes
Softscale Range
Scalable to 80kVA
External Battery Cabinet
Type
Quantity
Scalable to 120kVA
Scalable to 200kVA
Rated Output, kVA
Rated Output, kVA
Rated Output, kVA
40
60
80
80
100
120
160
200
UPS12-100MR
1
5
N/A
N/A
N/A
N/A
N/A
N/A
N/A
UPS12-150MR
1
12
6
N/A
N/A
N/A
N/A
N/A
N/A
UPS12-210MR
1
19
10
6
N/A
N/A
N/A
N/A
N/A
UPS12-300MR
1
32
19
12
13
9
6
N/A
N/A
UPS12-350MR
1
38
23
16
16
11
8
N/A
N/A
UPS12-400MR
1
41
28
19
20
14
10
6
N/A
UPS12-490MR
1
65
38
27
27
20
15
8
N/A
UPS12-540MR
1
68
40
31
31
23
17
10
6
UPS12-100MR
2
16
8
5
N/A
N/A
N/A
N/A
N/A
UPS12-150MR
2
31
18
12
N/A
N/A
N/A
N/A
N/A
UPS12-210MR
2
47
30
20
N/A
N/A
N/A
N/A
N/A
UPS12-300MR
2
74
46
33
33
25
20
13
9
UPS12-350MR
2
82
54
38
39
31
25
16
11
UPS12-400MR
2
101
64
45
46
36
28
19
14
UPS12-490MR
2
149
95
67
68
50
39
27
20
UPS12-540MR
2
156
99
70
71
53
41
31
23
UPS12-100MR
3
28
16
10
N/A
N/A
N/A
N/A
N/A
UPS12-150MR
3
50
32
22
N/A
N/A
N/A
N/A
N/A
UPS12-210MR
3
77
48
35
N/A
N/A
N/A
N/A
N/A
UPS12-300MR
3
122
75
53
53
40
34
22
17
UPS12-350MR
3
147
83
65
65
49
39
28
21
UPS12-400MR
3
159
103
73
74
55
46
33
25
UPS12-490MR
3
244
151
107
108
81
68
46
35
UPS12-540MR
3
258
158
112
113
83
71
49
37
UPS12-100MR
4
41
25
17
N/A
N/A
N/A
N/A
N/A
UPS12-150MR
4
71
41
32
N/A
N/A
N/A
N/A
N/A
UPS12-210MR
4
109
70
49
N/A
N/A
N/A
N/A
N/A
UPS12-300MR
4
162
106
76
76
56
47
33
25
UPS12-350MR
4
209
132
90
91
70
55
39
31
UPS12-400MR
4
224
146
103
104
79
66
45
35
UPS12-490MR
4
335
212
152
153
121
97
67
50
UPS12-540MR
4
343
222
159
160
130
101
70
53
Liebert® NX™
115
Specifications and Technical Data
116
Liebert® NX™
UPS Status Messages
APPENDIX A - UPS STATUS MESSAGES
Table 49 shows all event messages as they appear in the current status area of the LCD and in the
history log, along with a description and recommended actions, if any. For further information on the
current status area and the history log, see 2.11 UPS Status Messages.
Table 49
UPS status messages
Event Message
Description / Suggested Action (if any)
Inverter Comm. Fail
The RS-485 communication between internal monitor and inverter has failed. Contact Liebert
Services at 800-543-2378 for assistance.
Rectifier Comm. Fail
The RS-485 communication between internal monitor and rectifier fails. Contact Liebert
Services at 800-543-2378 for assistance.
Parallel Comm. Fail
The CAN communication between different UPS units within a parallel system has failed.
Check if there are some UPS units not powered on in the parallel system. If so, power on these
UPS units and check if the alarm disappears.
Press Fault Clear push button.
If alarm does not clear, contact Liebert Services at 800-543-2378
Battery Overtemp.
The battery temperature is over limit. Check the battery temperature and ventilation
Replace Battery
Battery should be replaced. Contact Liebert Services at 800-543-2378 for assistance.
Battery Low Pre-warning
Before the end of discharging, battery under-voltage pre-warning should occur. After this prewarning, battery should have the capacity for 3 minutes discharging with full load. The time is
user configured from 3 to 60 minutes.
Shut down the load in time to prevent damage to equipment and data.
Battery End of Discharge
Inverter turned off due to low battery voltage.
Check the utility failure and try to recover it.
Mains Volt. Abnormal
Mains voltage exceeds the upper or lower limit and results in rectifier shutdown.
Check the input line-to-line voltage amplitude of rectifier.
Mains Undervoltage
Mains voltage is undervoltage 288V~384V line to line voltage with derated load.
Check the input line-to-line voltage amplitude of rectifier.
Mains Freq. Abnormal
Mains frequency is out of limit range and results in rectifier shutdown.
Check the rectifier’s input voltage frequency
Rectifier Fault
Contact Liebert Services at 800-543-2378 for assistance.
Input Inductor Overtemp.
The temperature of rectifier inductor of rectifier common mode inductor is too high to keep the
rectifier running.
Check the ambient temperature and ventilation; contact Liebert Services at 800-543-2378 for
assistance.
Rectifier Overtemp.
The temperature of the heat sink is too high to keep the rectifier running.
The UPS can recover automatically. Check the environment and ventilation.
Charger Fault
The charger has a fault. Contact Liebert Services at 800-543-2378 for assistance.
Control Power 1 Fail
Control Power 1 has failed or has been lost. Contact Liebert Services at 800-543-2378 for
assistance.
Mains Phase Reversed
Input phase sequence is inverse. Contact Liebert Services at 800-543-2378 for assistance.
Rectifier Overcurrent
The current of rectifier is over limit. Contact Liebert Services at 800-543-2378 for assistance.
Soft Start Fail
Rectifier could not start due to low DC bus voltage. Contact Liebert Services at 800-543-2378
for assistance.
Bypass Unable to Trace
This alarm is triggered by an inverter software routine when the amplitude or frequency of
bypass voltage is beyond the normal range.
The amplitude threshold is fixed for positive and negative 10% rating.
This alarm automatically resets once the bypass voltage goes normal.
First verify that the bypass voltage and frequency displayed on the panel is within the selected
range. Note here the rated voltage and frequency are specified by “Output voltage level” and
“Output frequency level” respectively.
If the displayed voltage is believed to be abnormal, then verify the bypass voltage and frequency
presented to the UPS. Check the external supply if it is found to be faulty.
Contact Liebert Services at 800-543-2378 for assistance.
Liebert® NX™
117
UPS Status Messages
Table 49
UPS status messages
Event Message
Description / Suggested Action (if any)
Bypass Abnormal
This alarm is triggered by an inverter software routine when the amplitude or frequency of
bypass voltage exceeds the limit.
This alarm automatically resets once the bypass voltage goes normal.
First check whether there are relevant alarms such as “Bypass disconnect open,” “Bypass
phase reverse” and “Mains neutral lost.” If they appear, solve them first.
Then verify that the bypass voltage and frequency displayed on the panel is within the bypass
limit. Note here the rated voltage and frequency are specified by “Output voltage level” and
“Output frequency level” respectively.
If the displayed voltage is believed to be abnormal, then verify the bypass voltage and frequency
presented to the UPS. Check the external bypass supply if it is found to be faulty. If the utility is
likely to trigger this alarm frequently, the bypass limit can be increased through the configuration
software according to the customer’s agreement.
Contact Liebert Services at 800-543-2378 for assistance.
Inverter Asynchronous
This alarm is triggered by an inverter software routine when the inverter and bypass waveforms
are misaligned by more than 6 degrees in phase. This alarm resets automatically once the
condition clears.
First check if the alarm “Bypass unable to trace” or “Bypass abnormal” occurs. If so, solve it first.
Verify the waveform of the bypass voltage.
Contact Liebert Services at 800-543-2378 for assistance.
Inverter Fault
This alarm indicates a fault condition exists within the inverter.
Contact Liebert Services at 800-543-2378 for assistance.
Output Voltage Abnormal
This alarm indicates the inverter voltage waveform is abnormal.
Contact Liebert Services at 800-543-2378 for assistance.
Input Current Abnormal
This alarm indicates the rectifier input current is abnormal.
Contact Liebert Services at 800-543-2378 for assistance.
Inv. Inductor Overtemp.
The temperature of the inverter filter inductor or inverter common mode inductor is too high to
keep inverter running.
This alarm is triggered by the signal from a thermostat mounted in the inverter filter inductor.
The UPS would recover automatically after a 5 minute delay from the disappearance of the
overtemperature signal.
If the overtemperature condition is true then check for and verify:
High ambient air temperature.
Blocked cooling airway
Any fan failure
Prolonged inverter overload.
Contact Liebert Services at 800-543-2378 for assistance.
Inverter Overtemp.
The temperature of the inverter heat sink is too high to keep inverter running.
This alarm is triggered by the signal from a temperature monitoring thermostat on the inverter
bridge heat sink.
The UPS will recover automatically after a 5 minute delay from the disappearance of the
overtemperature signal.
If the overtemperature condition is true then check for and verify:
high ambient air temperature.
blocked cooling airway.
any fan failure.
prolonged inverter overload.
Contact Liebert Services at 800-543-2378 for assistance.
Fan Fault
At least one of the cooling fans has failed. Contact Liebert Services at 800-543-2378 for
assistance.
Inverter STS Fail
At least one of the static switches of inverter side is open or short circuit. This fault is locked until
power off. Contact Liebert Services for assistance at 800-543-2378 for assistance.
Bypass STS Fail
At least one of the static switches of bypass side is open or short-circuited. This fault is locked
until power off.
Contact Liebert Services at 800-543-2378 for assistance.
Output Fuse Fail
At least one of the output fuses is open. Contact Liebert Services at 800-543-2378 for
assistance.
Control Power 2 Fail
Control Power 2 is abnormal or lost. Contact Liebert Services at 800-543-2378 for assistance.
118
Liebert® NX™
UPS Status Messages
Table 49
UPS status messages
Event Message
Description / Suggested Action (if any)
Unit Overload
The UPS is overloaded when the load arises above 105% nominal rating.
The alarm automatically resets once the overload condition is removed.
Confirm that the alarm is true by checking the load percent indicated on the LCD panel to
determine which phase is being overloaded.
If the alarm is true, measure the actual output current to verify that the indications are valid.
Disconnect unnecessary load. In a parallel system, a severe load sharing error can also lead to
the alarm.
Contact Liebert Services at 800-543-2378 for assistance.
System Overload
The UPS parallel system is overloaded when the total load arises above 105% nominal rating
for the set basic number of UPS units. The alarm resets automatically once the overload
condition is removed.
Confirm that the alarm is true by checking the system load percent indicated on the LCD panel
to determine which phase is being overloaded.
If the alarm is true, measure the actual output current to verify that the indications are valid.
Disconnect unnecessary load and ensure the safety. In a parallel system, a severe load sharing
error can also leads to the alarm.
Unit Overload Timeout
The UPS is overloaded and the overload times out.
Note 1: The highest loaded phase will indicate overload timing-out first.
Note 2: When the timer is active then alarm “unit overload” should also be active as the load is
above nominal.
Note 3: When the timer has expired, the inverter Static Switch is opened and the load
transferred to bypass. The inverter shutdown and will restart after 1 seconds.
Note 4: If the load decreases lower than 95% after 5 minutes, the system will transfer back to
inverter mode.
Confirm that the alarm is genuine by checking the load percent indicated on the LCD. If an
overload is indicated then check the load, and investigate any additional load connected prior to
the alarm (if applicable).
Inverter Overcurrent
The current of inverter IGBT is over limit. If the fault will not reset, contact Liebert Services at
800-543-2378 for assistance.
Bypass Phase Reversed
The phase sequence direction of bypass voltage is reversed.
Normally, the phase of Phase B lags 120 degrees behind Phase A, and the phase of Phase C
lags 120 degrees behind Phase B.
Verify that the phase rotation of the bypass supply presented to the UPS is correct, and rectify it
if it is found to be in error. Contact Liebert Services at 800-543-2378 for assistance.
Load Impact Transfer
A transfer to bypass occurred due to a large step load. The UPS should recover automatically.
Turn on connected equipment in sequential order to reduce the step loading of the inverter.
Transfer Timeout
The load is on bypass power due to excessive number of transfers that occurred within the last
hour.
The UPS will recover automatically and will transfer the load back to inverter power within an
hour.
Load Sharing Fault
UPS units working within a parallel system are not sharing load current correctly. Contact
Liebert Services at 800-543-2378 for assistance.
DC Bus Abnormal
Shut off inverter due to abnormal DC bus voltage.
Contact Liebert Services at 800-543-2378 for assistance.
System Transfer
The whole paralleled UPS system transferred to bypass at the same time. This message will
appear on the UPS which passive transfer to bypass.
Parallel Board Fault
Parallel board is not working correctly. Contact Liebert Services at 800-543-2378 for assistance.
DC Bus Overvoltage
Rectifier, inverter and battery converter were shut down because DC bus voltage is too high.
Check whether there is a fault in rectifier side. If not, check whether overload occurs.
Restart the inverter after resetting the fault. If fault does not clear, contact Liebert Services at
800-543-2378 for assistance.
Parallel Connect Fault
The parallel cables are not connected correctly in a parallel system.
Reset the fault by pressing the Fault Clear button, then restart the inverter by pressing the
Inverter On button.
If the UPS does not resume normal operation, contact Liebert Services at
800-543-2378 for assistance.
Bypass Overcurrent
Bypass current is over limit above 135% rating. The UPS just alarms and does nothing. Refer to
your installation documentation or contact Liebert Services at 800-543-2378 for assistance.
Liebert® NX™
119
UPS Status Messages
Table 49
UPS status messages
Event Message
Description / Suggested Action (if any)
LBS Active
The LBS setting is active. The UPS is acting as an LBS master or slave in a dual bus
configuration.
Battery ground fault
Battery ground fault from dry contact signal. Contact Liebert Services at 800-543-2378 for
assistance.
Inverter turned On
manually
Manual Turn On via front panel
Inverter turned Off
manually
Manual Turn Off via front panel
EPO
Emergency Power Off
Transfer Confirm
Interrupted Transfer Confirm
Transfer Cancel
Interrupted Transfer is cancel
Unit Off Confirm
Unit Turned Off Confirm
System Off Confirm
Parallel System Turned Off Confirm
Fault Reset
Fault Reset
Alarm Silence
Alarm Silence
Turn On Fail
Turn On Fail
Alarm Reset
Audible Alarm Reset
Bypass Mode
UPS in Bypass Mode
Normal Mode
UPS in Normal Mode
Battery Mode
UPS in Battery Mode
Check UPS output
UPS Shutdown, output power-down
Output Disabled
UPS Output Disabled
Generator Connected
Generator is connected and a signal is sent to UPS
Input CB Open
Input CB is Open
Input CB Closed
Input CB is Closed
Bypass CB Open
Bypass CB is Open
Bypass CB Closed
Bypass CB is Closed
Output CB Open
Output CB is Open
Output CB Closed
Output CB is Closed
Maint. CB Open
Maintenance CB is Open
Maint. CB Closed
Maintenance CB is Closed
Battery Reverse
Connect the battery again and check the wiring of batteries
No Battery
Check the battery and the wiring of batteries
Auto start
After the UPS was shut down at end of discharge, inverter auto starts when utility is restored
BCB closed
BCB closed from dry contact signal
BCB open
BCB open from dry contact signal
Battery Float Charging
Battery is float charging
Battery Boost Charging
Battery is boost charging
Battery Mode
Battery is discharging
Battery Period Testing
Battery is period self-testing.
Batt. Capacity Testing
Battery is capacity self-testing.
Batt. Maint. Testing
Battery is maintenance self-testing.
UPS System Testing
UPS System is testing
Inverter in Setting
Inverter is in parameter setting
Rectifier in Setting
Rectifier is in parameter setting
120
Liebert® NX™
UPS Status Messages
Table 49
UPS status messages
Event Message
Description / Suggested Action (if any)
Balancer Fault
Internal VDC (+) and VDC (-) offset by over 50V exceeding the inverter DC offset compensation
capacity. Inverter shuts down. Load transfers to bypass.
Operation Invalid
This record is registered following an incorrect operation.
Byp. Abnormal Shutdown
Both bypass and inverter voltages unavailable. Load interruption
Setting Save Error
History records not saved (Reserved)
Protocol version clash
Firmware incompatibility between monitor board and digital signal processor board
MBP-T cabinet Fan Fault
Maintenance bypass cabinet fans fault
Ext Input TX Overtemp
External input isolation transformer overtemperature
Ext Output TX Overtemp
External output isolation transformer overtemperature
Battery Room Alarm
Environment in Battery Room Needs Attention
Rec Flash Update
Rectifier firmware is being updated
Inv Flash Update
Inverter firmware is being updated
Monitor Flash Update
Monitor firmware is being updated
Input contactor fault
Input contactor fault
LBS abnormal
LBS is abnormal
DSP firmware error
The inverter firmware is not compatible with the rectifier firmware.
Fan power fail
Fan power has failed
Keyboard fault
Keyboard has a fault. Check the cable between keyboard with U2 board. Contact Liebert
Services at 800-543-2378 for assistance.
KVA Invalid
An invalid kVA has been configured in unit.Contact Liebert Services at 800-543-2378 for
assistance.
KVA updated
The capacity updating is successful.
Output ground fault
Output Line is shorted with ground
Liebert® NX™
121
Technical Support / Service
Web Site
www.liebert.com
Monitoring
liebert.monitoring@emerson.com
800-222-5877
Outside North America: +00800 1155 4499
Single-Phase UPS & Server Cabinets
liebert.upstech@emerson.com
800-222-5877
Outside North America: +00800 1155 4499
Three-Phase UPS & Power Systems
800-543-2378
Outside North America: 614-841-6598
Environmental Systems
800-543-2778
Outside the United States: 614-888-0246
Locations
While every precaution has been taken to ensure the accuracy
and completeness of this literature, Liebert Corporation assumes no
responsibility and disclaims all liability for damages resulting from use of
this information or for any errors or omissions.
© 2014 Liebert Corporation
All rights reserved throughout the world. Specifications subject to change
without notice.
® Liebert is a registered trademark of Liebert Corporation.
All names referred to are trademarks
or registered trademarks of their respective owners.
SL-25217_REV5_10-14
Emerson Network Power
Liebert
www.emerson.com
United States
1050 Dearborn Drive
P.O. Box 29186
Columbus, OH 43229
Europe
Via Leonardo Da Vinci 8
Zona Industriale Tognana
35028 Piove Di Sacco (PD) Italy
+39 049 9719 111
Fax: +39 049 5841 257
Asia
29/F, The Orient Square Building
F. Ortigas Jr. Road, Ortigas Center
Pasig City 1605
Philippines
+63 2 687 6615
Fax: +63 2 730 9572
Rev. Date: 08-09