advertisement
Touchstone
®
WTM652
Telephony Modem
User’s Guide
Get ready to experience the Internet’s express lane! Whether you’re checking out streaming media, downloading new software, checking your email, or talking with friends on the phone, the Touchstone WTM652 Telephony Modem brings it all to you faster and more reliably. All while providing toll quality Voice over IP telephone ser vice and both wired and wireless connectivity. Some models even provide a Lithi um-Ion battery backup to provide continued telephone service during power outages.
The Touchstone Telephony Modem provides four Ethernet connections for use as the hub of your home/office Local Area Network (LAN). The Touchstone Telephony
Modem also provides 802.11b/g wireless connectivity for enhanced mobility and versatility. In addition, the Touchstone Telephony Modem provides for up to two separate lines of telephone service.
Installation is simple and your cable company will provide assistance to you for any special requirements. The links below provide more detailed instructions.
Battery Installation and Removal (WTM652G only)
Installing and Connecting Your Telephony Modem
Configuring Your Wireless Connection
Configuring Your Ethernet Connection
Export Regulations
This product may not be exported outside the U.S. and Canada without U.S. Department of Commerce, Bureau of Export Admin istration authorization. Any export or re-export by the purchaser, directly or indirectly, in contravention of U.S. Export Adminis tration Regulation is prohibited.
Copyright © 2009-2013 ARRIS. All rights reserved.
The information in this document is subject to change without notice. The statements, configurations, technical data, and recom mendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this docu ment is proprietary to ARRIS.
ARRIS, Touchstone, and the ARRIS logo are trademarks or registered trademarks of ARRIS Group. All other trademarks and reg istered trademarks are the property of their respective holders.
Protected under one or more of the following U.S. patents: 7,031,435; 7,100,011. Other patents pending.
ARSVD01202
Release 6 Standard 1.2 June 2013
Safety Requirements
ARRIS Telephony Modems comply with the applicable requirements for performance, construction, labeling, and information when used as outlined below:
CAUTION
Risk of shock
Mains voltages inside this unit. No user serviceable parts inside. Refer service to qualified personnel only!
CAUTION
Potential equipment damage
Potential loss of service
Connecting the Telephony Modem to existing telephone wiring should only be performed by a professional installer. Physical connections to the previous telephone provider must be removed and the wiring must be checked; there must not be any voltages. Cancellation of telephone service is not adequate. Failure to do so may result in loss of service and/or permanent damage to the Telephony Modem.
CAUTION
Risk of explosion
Replacing the battery with an incorrect type, heating a battery above
75°C, or incinerating a battery, can cause product failure and a risk of fire or battery explosion. Dispose of used batteries according to the
instructions.
• The Telephony Modem is designed to be connected directly to a telephone.
• Connecting the Telephony Modem to the home’s existing tele phone wiring should only be performed by a professional in staller.
• Do not use product near water (i.e. wet basement, bathtub, sink or near a swimming pool, etc.), to avoid risk of electrocu tion.
Touchstone WTM652 Telephony Modem User’s Guide 3
• Do not use spray cleaners or aerosols on the Telephony Modem.
• Avoid using and/or connecting the equipment during an electri cal storm, to avoid risk of electrocution.
• Do not use the telephone to report a gas leak in the vicinity of the leak.
• Do not locate the equipment within 6 feet (1.9 m) of a flame or ignition source (i.e. heat registers, space heaters, fireplaces, etc.).
• Use only power supply and power cord included with the equip ment.
• Equipment should be installed near the power outlet and should be easily
accessible.
• The shield of the coaxial cable must be connected to earth (grounded) at the entrance to the building in accordance with applicable national electrical installation codes. In the U.S., this is required by NFPA 70 (National Electrical
Code) Article 820. In the European Union and in certain other countries,
CATV instal lation equipotential bonding requirements are specified in IEC
60728-11, Cable networks for television signals, sound signals and interac-
tive services, Part 11: Safety. This equipment is in tended to be installed in accordance with the requirements of IEC 60728-11 for safe operation.
If the equipment is to be installed in an area serviced by an IT power line network, as is found in many areas of Norway, spe cial attention should be given that the installation is in accor dance with IEC 60728-11, in particular
Annex B and Figure B.4.
• In areas of high surge events or poor grounding situations and areas prone to lightning strikes, additional surge protection may be required (i.e.
PF11VNT3 from American Power Conver sion) on the AC, RF, Ethernet and
Phone lines.
• When the Telephony Modem is connected to a local computer through Ethernet cables, the computer must be proper ly grounded to the building/residence AC ground network. All plug-in cards within the computer must be properly installed and grounded to the computer frame per the manufacturer’s specifications.
Touchstone WTM652 Telephony Modem User’s Guide 4
FCC Part 15
This equipment has been tested and found to comply with the requirements for a
Class B digital device under Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 7.9 inches (20cm) between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Touchstone WTM652 Telephony Modem User’s Guide 5
Industry Canada Compliance
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
For Mexico
The operation of this equipment is subject to the following two conditions: (1) This equipment or device cannot cause harmful interference and (2) this equipment or device must accept any interference, including interference that may cause some unwanted operation of the equipment.
Touchstone WTM652 Telephony Modem User’s Guide 6
European Compliance
This product complies with the provisions of the Electromagnetic Com patibility
(EMC) Directive (89/336/EEC), the Amending Directive (92/31/EEC), the Low Voltage Directive (73/23/EEC), and the CE Marking Directive (93/68/EEC). As such, this product bears the CE marking in accordance with the above applicable Directive(s).
A copy of the Declaration of Conformity may be obtained from: ARRIS International, Inc., 3871 Lakefield Drive, Suite 300, Suwanee, GA 30024.
As indicated by this symbol, disposal of this prod uct or battery is governed by Directive 2002/96/EC of the European Parliament and of the Council on waste electrical and electronic equipment
(WEEE). WEEE could potentially prove harmful to the environment; as such, upon disposal of the Te lephony Modem the Directive requires that this product must not be disposed as unsorted munic ipal waste, but rather collected separately and dis posed of in accordance with local WEEE ordinances.
This product complies with directive 2002/95/EC of the European
Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances (RoHS) in electrical and electronic equip ment.
Touchstone WTM652 Telephony Modem User’s Guide 7
Getting Started
About Your New Telephony Modem
The Touchstone WTM652 Telephony Modem is DOCSIS or Euro-DOCSIS compliant with the following features:
• Speed: much faster than dialup or ISDN service
• Convenience: supports Ethernet and 802.11b/g wireless connections; both can be used simultaneously
• Flexibility: provides two independent lines of telephone service as well as high speed data
• Compatibility: supports tiered data services (if offered by your cable company)
All WTM652 models provide:
• Wireless 802.11b/g connectivity
• Four Ethernet ports for connections to non-wireless devices
• Up to two lines of telephone service
Your WTM652 model is one of the following:
• WTM652A: DOCSIS compliant
• WTM652B: Euro-DOCSIS compliant
• WTM652G: DOCSIS compliant with Li-Ion backup battery
What’s in the Box?
Make sure you have the following items before proceeding. Call your cable company for assistance if anything is missing.
• Telephony Modem
• Antenna
• Power Cord
Touchstone WTM652 Telephony Modem User’s Guide 8
Coax Cable
Phone Cable
• Quick Installation Guide
• Ethernet Cable
• End User License Agreement
Items You Need
If you are installing the Telephony Modem yourself, make sure you have the follow ing items on hand before continuing:
•
Telephony modem package: see What’s in the Box?
for a list of items in the package.
• Coaxial cable (coax): as shown in the image to the left, this is a round cable with a connector on each end. It is the same kind of wire used to connect to your television for cable TV. You can buy coax from any electronics retailer and many discount stores; make sure it has connectors on both ends. There are two types of connectors, slip-on and screw-on; the screwon connectors are best for use with your Telephony Modem. The coax should be long enough to reach from your Telephony Modem to the nearest cable outlet.
• Phone Cable: as shown in the image to the left, this is a standard phone cable with standard phone connectors (RJ11 type) on both ends. You can buy phone cables from any electronics retailer and many discount stores.
• Splitter (optional): provides an extra cable connection by splitting a single outlet into two. You may need a splitter if you have a TV already connected to the cable outlet that you want to use. You can buy a splitter from any electronics retailer and most discount stores; you may also need a short piece of coax cable (with connectors); use it to connect the splitter to the cable outlet and then connect the Telephony Modem and TV to the splitter.
Note: A splitter effectively cuts the signal in half and sends each half to its two outputs. Using several splitters in a line may deteriorate the quality of your television, telephone, and/or internet connection.
• Wall-mount hardware (optional): if you want to wall-mount your Telephony Modem, you need to obtain two drywall anchors or wood screws. See the Wall-Mount Template and Instructions for more details.
Touchstone WTM652 Telephony Modem User’s Guide 9
• Information packet: your cable company should furnish you with a packet containing information about your service and how to set it up. Read this information carefully and contact your cable company if you have any questions.
Getting Service
Before trying to use your new Telephony Modem, contact your local cable company to establish an Internet account and telephone service. When you call, have the fol lowing information ready:
• the Telephony Modem serial number and cable MAC addresses of the unit
(printed on a sticker on the bottom of the Telephony Modem, as shown on the next page)
• the model number of the Telephony Modem
If the Telephony Modem was provided by your cable company, they already have the required information.
In addition, you should ask your cable company the following questions:
• Do you have any special system requirements or files that I need to download after I am connected?
• When can I start using my Telephony Modem?
• Do I need a user ID or password to access the Internet or my e-mail?
• Will my phone number(s) change?
• What new calling features will I have and how do I use them?
Touchstone WTM652 Telephony Modem User’s Guide 10
FOR HOME OR OFFICE USE
System Requirements
The Touchstone Telephony Modem operates with most computers. The following describes requirements for each operating system; see the documentation for your system for details on enabling and configuring networking.
To use the Telephony Modem, you need DOCSIS high-speed Internet service from your cable company.
Windows
Windows XP, Windows Vista, or Windows 7. A supported Ethernet or wireless LAN connection must be available.
MacOS
System 7.5 to MacOS 9.2 (Open Transport recommended) or MacOS X. A supported
Ethernet or wireless LAN connection must be available.
Linux/other Unix
Hardware drivers, TCP/IP, and DHCP must be enabled in the kernel. A supported
Ethernet or wireless LAN connection must be available.
About this Manual
This manual is written to cover all of the different WTM652 models. Your model may or may not have all of the capabilities outlined in this manual. To determine which model you have purchased, refer to the image at the left. The model number is on the label affixed to the Telephony Modem.
Model Number
Touchstone WTM652 Telephony Modem User’s Guide 11
Ethernet Cable
Ethernet or Wireless?
There are two ways to connect your computer (or other equipment) to the Telephony Modem. The following will help you decide which is best for you:
Ethernet
Ethernet is a standard method of connecting two or more computers into a Local
Area Network (LAN). You can use the Ethernet connection if your computer has built-in Ethernet hardware.
Note: To connect more than four computers to the WTM652 through the Ether net ports, you need an Ethernet hub (available at computer retail ers).
The Telephony Modem package comes with one 6-foot (1.9m) Ethernet cable (the connectors look like wide telephone connectors); you can purchase more cables if necessary at a computer retailer. If you are connecting the Telephony Modem directly to a computer, or to an Ethernet hub with a cross-over switch, ask for Category 5 (CAT5) straight-through cable. If you are connecting the Telephony Modem to an Ethernet hub without a crossover switch, ask for a Category 5 crossover cable.
Wireless
The 802.11 wireless LAN standard allows one or more computers to access the
WTM652 using a wireless (radio) signal. You can use the wireless connection if your computer has a built-in or aftermarket wireless card.
Note: To learn more about which wireless hardware works best with your computer, see your computer dealer.
Both
If you have two or more computers, you can use Ethernet for up to four devices and wireless for others. To connect five or more computers to the Ethernet ports, you will need an Ethernet hub (available at computer retailers).
For more information about connecting two or more computers, contact your cable service provider.
Touchstone WTM652 Telephony Modem User’s Guide 12
What About Security?
Having a high-speed, always-on connection to the Internet requires a certain amount of responsibility to other Internet users—including the need to maintain a reasonably secure system. While no system is 100% secure, you can use the following tips to enhance your system’s security:
• Keep your operating system updated with the latest security patches. Run the system update utility at least weekly.
• Keep your email program updated with the latest security patches. In addition, avoid opening email containing attachments, or opening files sent through chat rooms, whenever possible.
• Install a virus checker and keep it updated.
• Avoid providing web or file-sharing services over your Telephony Modem.
Besides certain vulnerability problems, most cable companies prohibit running servers on consumer-level accounts and may suspend your account for violating your terms of service.
• Use the cable company’s mail servers for sending email.
•
software unless you are certain that it is not open for abuse by other Internet users (some are shipped open by default). Criminals can take advantage of open proxies to hide their identity when breaking into other computers or sending spam. If you have an open proxy, your ca ble company may suspend your account to protect the rest of the network.
• If you use the wireless LAN, make sure you enable wireless security on the
Telephony Modem (for the same reasons that you should run only secured proxies). See “Wireless Configuration” for help.
Touchstone WTM652 Telephony Modem User’s Guide 13
Battery Installation and Removal
(WTM652G only)
Many Telephony Modem models support an optional Lithium-Ion backup battery.
The WTM652G supports the following battery models:
• Basic backup battery — provides up to 5 hours (black) or 8 hours (grey) of backup time, depending on your Telephony Modem model and usage. It may be light grey (recommended battery) or black.
• Extended backup battery — provides up to 12 hours of backup time, depending on model and usage. It has a strap between the battery guides.
• Maximum backup battery — provides up to 24 hours of backup time, depending on model and usage. It replaces the battery door, and increases the height of the Telephony Modem by about 5/8 inch (16 mm).
Touchstone WTM652 Telephony Modem User’s Guide 14
Your cable company may include a backup battery with your Telephony Modem.
You can order any of the batteries shown here at http://yourbroadbandstore.com/
Basic Backup Battery Installation
1 Pull back the battery door latch and remove the battery door. Set the door aside.
2 Align the guides on the battery with the slots on the Telephony Modem as shown below, and slide the battery into the bay.
Battery Slot
Battery Guide
Touchstone WTM652 Telephony Modem User’s Guide 15
3 Push the battery pack into the bay until it seats into place. Push on the center of the battery to avoid inserting the battery at an angle.
4 Replace the battery door: insert the hinge tabs in the receiver slots, and close the door until the latch snaps into place.
Receiver
Slots
Hinge tabs
Touchstone WTM652 Telephony Modem User’s Guide 16
Extended Backup Battery Installation
1 Pull back the battery door latch and remove the battery door. Set the door aside.
2 Stand the Telephony Modem on its top, so the battery bay faces up.
3 Align the guides on the battery with the slots on the Telephony Modem as shown below, and slide the battery into the bay.
Note: Batteries will not insert completely into the Telephony Modem if not oriented correctly. The battery should slide into the bay without significant force. Line up the slots in the battery bay with the guides on the battery and apply even pressure on both ends of the battery.
WRONG WRONG RIGHT
Touchstone WTM652 Telephony Modem User’s Guide 17
4 Replace the battery door: insert the hinge tabs in the receiver slots, and close the door until the latch snaps into place.
Receiver
Slots
Hinge Tabs
Touchstone WTM652 Telephony Modem User’s Guide 18
Maximum Backup Battery Installation
1 Pull back the battery door latch and remove the battery door. The Maximum
Backup battery replaces the door; store the door in a safe place.
2 Place the battery on a firm horizontal surface.
3 Position the Telephony Modem over the battery, aligning the slots on the battery bay with the tabs on the battery. Push straight down on the Telephony Modem until the battery latch clicks into place.
Note: You may need to push down gently on the front of the Telephony
Modem to latch the battery into place.
Touchstone WTM652 Telephony Modem User’s Guide 19
Basic and Extended Backup Battery Removal
1 Pull back the battery door latch and remove the battery door. Set the door aside.
Latch End
2a Basic Backup battery removal: Insert a finger behind the battery tab where shown below, and place your thumb over the other end of the battery. Pull out gently until the battery disconnects and slides out of the bay.
Tab
Touchstone WTM652 Telephony Modem User’s Guide 20
2b Extended Backup battery removal: Pull the strap until the battery disconnects and slides out of the bay.
Battery
Pull Strap
Touchstone WTM652 Telephony Modem User’s Guide 21
Maximum Backup Battery Removal
1 Grasp the battery and pull back on the latch at the front of the battery.
2 Gently rock the battery out of the bay.
Latch
Touchstone WTM652 Telephony Modem User’s Guide 22
Installing and Connecting Your
Telephony Modem
Before you start, make sure that:
• You have contacted your cable company and verified that they provide data and telephone service using standard DOCSIS technology.
•
You have all the items you need .
• Cable, phone, and power outlets are available near the computer. If a cable outlet is not conveniently located, your cable company can install a new one.
CAUTION
Risk of equipment damage
Only qualified installation technicians should connect the Telephony
Modem to house wiring. Incumbent telephone service must be physically disconnected at the outside interface box before making any connections.
Touchstone WTM652 Telephony Modem User’s Guide 23
C
A B
D
A C
E G
F
Se cur e
WL
AN
H
G I
B D E F H J
Front Panel
The front of the Telephony Modem has the following indicators:
A Battery: (WTM652G only) indicates the battery status.
B Telephone 1/2: indicates the status of each telephone line.
C Secure: indicates Wireless Protected Setup (WPS) is active.
D WLAN: indicates the status of the wireless LAN.
E LAN 1–4: indicates the status of each Ethernet port.
F Link: indicates Ethernet or wireless connectivity between the Telephony-
Modem and computers.
G Online: indicates internet data transmission status.
H US: indicates upstream connectivity.
I DS: indicates downstream connectivity.
J Power: indicates whether AC power is available to the unit.
Rear Panel
The rear of the Telephony Modem has the following connectors and controls:
A Tel 1 (A/B models): connector for the first phone line.
Tel 1/2 (G models): connector for the first phone line (or both lines of a
2-line phone).
B Tel 2: connector for the second phone line.
C Antenna: connector for the wireless antenna.
D Ethernet: for use with a computer LAN port.
E Router Reset button: resets the Ethernet and wireless ports without affect ing telephony service.
F TM Reset button: resets the Telephony Modem as if you power cycled the unit. Use a pointed non-metallic object to press this button.
G Cable: connector for the coaxial cable.
H Power: connector for the power cord.
Touchstone WTM652 Telephony Modem User’s Guide 24
Selecting an Installation Location
There are a number of factors to consider when choosing a location to install your
Telephony Modem:
• Is an AC outlet available nearby? For best results, the outlet should not be switched and should be close enough to the Telephony Modem that extension cords are not required.
• Is a cable jack available? For best performance, keep the number of splitters between the jack and cable drop to a minimum. Each splitter attenuates
(re duces) the signal available to the Telephony Modem. A large number of split ters can slow down the Internet connection and even affect your telephone service.
• Can you easily run cables between the Telephony Modem’s location and the phones?
• If you are connecting devices to the Ethernet ports, can you easily run cables between the Telephony Modem’s location and those devices?
• If you want to mount the Telephony Modem on a wall, does the location provide a solid surface for secure attachment? For best results when mounting the Telephony Modem on drywall, position the Telephony Modem so at least one of the screws are fastened to a stud. This may prevent the Telephony
Modem from pulling out of the wall in the future.
• If you want to install the Telephony Modem on a desktop, is there enough space on either side to keep the vents clear? Blocking the vents may cause overheating.
• How close are your wireless devices? The Telephony Modem wireless con nection range is typically 100–200 feet (30m–65m). A number of factors can affect connection range, as described below.
Touchstone WTM652 Telephony Modem User’s Guide 25
Factors Affecting Wireless Range
A number of factors can affect the usable range for wireless connections.
Increases range:
Decreases range:
• Raising the antenna above the devices (for example, in stalling the Telephony Modem in the upper floor of a multi-story dwelling or using an aftermarket omnidirec tional antenna)
• Using an aftermarket directional antenna (increases range in one direction while decreasing range in other directions)
• Adding wireless hubs in a bridge (WDS) network
• Lowering the antenna below the devices (for example, installing the Telephony Modem in a basement)
• Removing the antenna
• Metal or concrete walls between the Telephony Modem and other devices
• Large metal appliances, aquariums, or metal cabinets between the Telephony Modem and other devices
• Interference and RF noise (2.4 GHz wireless phones, microwave ovens, or other wireless networks)
Note that decreasing the range of your wireless network may be beneficial, as long as the decreased range is sufficient for your needs. By limiting your network’s range, you reduce interference with other networks and make it harder for unwant ed users to find and connect to your network.
Touchstone WTM652 Telephony Modem User’s Guide 26
Step 1
Step 3
Step 2
Step 4
Mounting the Telephony Modem
You can either mount the Telephony Modem on a wall or place it on a desktop.
For wall-mount applications, you can mount the Telephony Modem with the indicators facing upward (vertical) or to the side (horizontal).
Tools and Materials
For wall-mounted installations, make sure you have the following tools and materials before proceeding:
• for mounting on drywall: Two 1/4” (6mm) drywall anchors and a drill with
1/4” (6mm) bit (not included)
• for mounting on plywood or studs: two #6 x 1.5” (38.1 mm) self tapping screws (not included)
• screwdriver (flat-blade or Phillips, depending on what kind of screws you use)
• wall-mount template (included)
• transparent tape: for temporarily securing the mounting template to the wall
(not included)
Wall-mounting instructions
1 Position the mounting template on the surface where you intend to mount the Telephony Modem and secure in place with transparent tape.
2 Drill holes through the template in the specified locations for the mounting screws. After drilling holes, remove the template from the surface.
3 If using drywall anchors, set them into the wall. Then, drive the screws into the wall leaving a gap of about 1/8” (3 mm) between the screw head and the wall. If not using anchors, just drive the screws.
4 Orient the Telephony Modem with the indicator lights facing up or right, as desired. Slip both mounting slots (in the back of the Telephony Modem) over the screws, then slide the case down until the narrow end of the keyhole slot contacts the screw shaft.
5 Proceed to Connecting the Telephony Modem .
Touchstone WTM652 Telephony Modem User’s Guide 27
C
A B
D
E G
F
H
Desktop mounting instructions
1 Position the Telephony Modem so that:
• air flows freely around it
• the back faces the nearest wall
• it will not fall to the floor if bumped or moved
2 Proceed to Connecting the Telephony Modem .
Connecting the Telephony Modem
WARNING
Risk of injury or equipment damage
Connecting the Telephony Modem to the home’s existing telephone wiring should only be performed by a professional installer. Physical connections to the previous telephone provider must be removed and the wiring must be checked; there must not be any voltage. Cancellation of telephone service is not adequate. Failure to do so may result in loss of service and/or permanent damage to the Telephony Modem.
1 Thread the antenna onto the Antenna connector on the back of the Telepho ny Modem (C). Tighten only by hand. Turn the antenna so that it points straight up, if possible.
2 Connect one end of the coax cable to the cable outlet or splitter, and the other end to the Telephony Modem’s Cable connector (G). Tighten the connections by hand, then tighten an additional 1/8 turn with a wrench.
Note: For best performance, use high-quality coax cable and minimize or eliminate splitters between the cable jack and the Telephony Modem.
3 Insert the plug from the power cord into the Power connector on the back of the Telephony Modem (H) and insert the power cord into a convenient AC outlet.
if the Power light does not turn on.
Touchstone WTM652 Telephony Modem User’s Guide 28
4 Connect one end of the Ethernet cable to any Ethernet port on the back of the Telephony Modem, (D) and the other end to the Ethernet port on a computer, hub, or broadband router.
Note: If you are connecting to a computer, use the Ethernet cable included in the Telephony Modem package.
5 Connect one end of the telephone cable to the telephone port on the back of the Telephony Modem (A or B). Connect the other end to the telephone.
Touchstone WTM652 Telephony Modem User’s Guide 29
2
1
3
Configuring Your Wireless Connection
The WTM652 ships with a basic factory default configuration that should allow you to immediately access the Internet with a wireless connection. If your computer is equipped with a 802.11b/g wireless LAN card, you may wish to configure the
WTM652 wireless settings. At a minimum, ARRIS suggests that you configure security settings.
Requirements
Make sure you have the following before attempting to configure your Ethernet connection:
• Computer with:
— Ethernet interface or wireless interface
— Ethernet cable, if using Ethernet interface (supplied)
• Web browser
Configuration Basics
The WTM652 uses a web-based interface to configure wireless settings. The follow ing screen shows the various components of the interface.
1 Access bar: Shows the WTM652 connection status and provides the following links:
• Home — returns to the Status page (shown above) from any screen.
• Help — displays help for the current screen.
• Login/Logout — allows access to screens other than the Status screen.
2 Navigation menu: Select any of the items in this list to display an associ ated submenu. Selecting submenu items displays the associated screen. If you are not logged in, the WTM652 displays the login screen before allowing you to proceed.
3 Display area: Enter or view configuration information in this area. A ? link may be available to explain the purpose of the screen or individual items on the screen.
Touchstone WTM652 Telephony Modem User’s Guide 30
Accessing the Configuration Interface
1 Use the connection utility for your operating system to connect to the wireless LAN arris54g (this is the Telephony Modem’s factory default SSID).
2 In your web browser, open the page http://192.168.2.1/ to display the
Status screen:
Touchstone WTM652 Telephony Modem User’s Guide 31
3 Click the Login link in the Access bar to display the Login screen:
Note: The Telephony Modem ships with no password configured. When you log in for the first time, leave the Password field blank.
4 Click the Submit button to return to the Status screen.
Note: The Access bar should now show Logout in place of Login.
5 Proceed to Configuring System Settings .
Touchstone WTM652 Telephony Modem User’s Guide 32
Configuring System Settings
1 Click the Utilities link (at the bottom of the Navigation menu) to open the
Utilities menu, then click System Settings to access the System Settings screen:
2 Make changes as follows:
• Enter Current Password: If you have already created a password, and you want to change settings on this screen, enter the password here.
• Enter New Password: Enter a password that you will remember but is not easy to guess.
• Confirm new Password: Enter the same password again.
Touchstone WTM652 Telephony Modem User’s Guide 33
• Time Zone: Select the proper time zone for your location. The Telephony Modem uses an Internet time server to set its internal clock.
3 Scroll down to the bottom of the page and click the Save button. If you are prompted to log in again, type your new password and click the Submit but ton.
4 Proceed to Setting Up Your WAN Connection .
Setting Up Your WAN Connection
Follow these steps to set up your WAN connection.
1 Click the WAN Setup link in the navigation menu, then click Connection Type.
The Connection Type screen appears:
2 Choose the correct connection type in the Connection Type screen. Most ca ble companies require the Dynamic connection type. If your cable company requires a different connection type, you should have an information sheet that shows the proper connection type to select and other information need ed to set up the connection.
Touchstone WTM652 Telephony Modem User’s Guide 34
3 Click the Next button at the bottom of the screen (you may have to scroll down in the browser to see the Next button). The Telephony Modem displays a screen showing further settings for your connection type. Follow the appropriate link for your connection type:
•
•
•
•
Dynamic
a. Fill in the Host Name field, using any name you want.
b. If you need to clone your computer’s MAC address, click the Change WAN
MAC Address link and proceed to Setting the MAC Address .
c. Click the Save button.
d. Proceed to Configuring the LAN Channel and Name .
Touchstone WTM652 Telephony Modem User’s Guide 35
Static
a. Fill in the IP Address, Subnet Mask, and ISP Gateway address fields with the information provided by your cable company.
b. If you need to enter DNS settings, click the link and proceed to Setting Up
c. Click the Save button.
d. Proceed to Configuring the LAN Channel and Name .
Touchstone WTM652 Telephony Modem User’s Guide 36
PPPoE
a. Fill in the User Name and Password fields with the information provided by your cable company. Enter the password a second time in the Retype
Password field.
b. If you need to change the MTU size or fill in the Service Name, enter the information as specified by your cable company.
c. Click the Save button.
d. Proceed to Configuring the LAN Channel and Name .
Touchstone WTM652 Telephony Modem User’s Guide 37
L2TP
a. Fill in the L2TP Account, L2TP Password, Host Name, and Service IP
Address fields with the information provided by your cable company. Enter the password a second time in the Retype Password field.
b. If you need to enter a static IP address and subnet mask, enter the information as specified by your cable company. Otherwise, select “Get Dynamically from ISP.”
c. If you need to enter DNS settings, click the link and proceed to Setting Up
d. Click the Save button.
e. Proceed to Configuring the LAN Channel and Name .
Touchstone WTM652 Telephony Modem User’s Guide 38
Setting the MAC Address
Some cable companies authenticate customers by the MAC address of your comput er. In some cases, you may need to change the MAC address of the Telephony
Mo dem’s WAN port. Follow these steps only if your cable company requires this change.
1 From the current Connection Type screen, click the MAC Address link.
The MAC address window appears:
Finding the MAC Address of a computer
Locate the operating system of your computer and follow the instructions to find its MAC address.
Windows: from the Start menu, select Settings then
Control Panel. Double-click “Network Connections,” then click the “Wireless Network Connection” for wireless or
“Local Area Connection” for Ethernet. Click the Support tab, then click the Details button. The “Physical Address” line shows the MAC address.
MacOS X: open System Preferences and click the Network icon. To find the Ethernet MAC address, select
Built-in Ethernet from the Show drop-down, then click the Ethernet tab; the “Ethernet ID” field shows the MAC address. To find the wireless MAC address, select Air-
port from the Show drop-down, then click the Airport tab; the “Airport ID” field shows the MAC address.
Linux: open a shell window and type /sbin/ifconfig
(and press Return). The wireless interface is eth1 (unless there is no Ethernet adapter, in which case the interface is eth0).
2 If the MAC address required is that of the computer you are using to set up the Telephony Modem, click the Clone button.
The Telephony Modem updates the WAN MAC Address field with the MAC address of your computer.
3 If you need to enter a MAC address manually, enter the hex digits (0-9, a-
f) in the WAN MAC Address field. If you need help determining the MAC address, see “Finding the MAC Address of a computer” in the sidebar.
4 Click the Save button to continue.
5 To configure DNS settings, proceed to
Setting Up DNS . Otherwise, proceed
to Configuring the LAN Channel and Name .
Touchstone WTM652 Telephony Modem User’s Guide 39
Setting Up DNS
Follow these steps to set up DNS.
1 From the current Connection Type screen, click the “Set Up DNS” link.
The DNS screen appears:
2 If your cable company has provided you with the IP addresses for their DNS servers, enter the IP addresses in the DNS Address and Secondary DNS Address fields.
3 If you have not received DNS server information, check Automatic from
ISP.
4 Click the Save button to return to the Status screen.
5 Proceed to Configuring the LAN Channel and Name .
Touchstone WTM652 Telephony Modem User’s Guide 40
Configuring the LAN Channel and Name
1 Click the Wireless Setup link to open the Wireless menu, then click the Channel and SSID link to open the Channel and SSID screen:
2 Make the following changes to this screen as desired:
• Wireless Channel: Use the default shown in most cases. You may need to change the channel if neighbors have wireless routers, or if you lose your connection while using certain remote telephones.
•
SSID : Give your wireless LAN any name you desire. For best security, do
not use your name or address. The default SSID is arris54g.
• Broadcast SSID: Uncheck to prevent passers-by from seeing your wireless LAN name in their connection utility. This provides only a small amount of extra security, since many wireless utilities can learn an SSID by listening to wireless traffic.
• Protected Mode: Set to On only if needed to overcome interference.
3 Click the Save button.
4 Proceed to Configuring Wireless Security .
Touchstone WTM652 Telephony Modem User’s Guide 41
Configuring Wireless Security
1 Click the Security link under the Wireless menu to open the Security screen:
2 In the Security Mode menu, choose WPA
or WPA-Enterprise unless you have wireless equip ment that does not support WPA; in that case, choose
128-bit WEP (more secure) or 64-bit WEP (more compatible with older wireless equipment).
The WTM652 displays a screen to allow you to configure the chosen mode.
The following screens show WPA and 128-bit WEP screens.
3 Enter a password or pass phrase in the text box. For WEP security, click the
Generate button to the right of the text box to create the hex key.
Note: Do not make changes to the other items unless required by your oth er wireless equipment.
4 Click the Save button.
Touchstone WTM652 Telephony Modem User’s Guide 42
Configuring Wi-fi Protected Setup (WPS)
Wi-fi Protected Setup (WPS) is a standard method for easily configuring a secure connection between your WTM652 and computers or other wifi-capable devices
(known as enrollees). Follow these steps to use WPS to connect to the WTM652.
1 Click the Wireless Setup link in the navigation menu, then click Wi-Fi Protected Setup.
The Wi-Fi Protected Setup window appears.
2. Check the WPS Enable box in the WTM652 screen.
3 Use the appropriate connection method as described below:
a. If your client device has a “Wi-Fi Protected Setup” button: Press the button on the client device, then click the Simple Push Button button on the
WTM652 screen.. When the client indicates that it has configured successfully, click the Save button in the WTM652 screen and refer to your client device documentation for further instructions.
b. If your client device has a WPS PIN number: Check the WPS Enable box in the WTM652 screen, and enter the client’s PIN in the Enrollee PIN field on the WTM652 screen.
Touchstone WTM652 Telephony Modem User’s Guide 43
c. If your client device asks for the router’s PIN number: Enter the WTM652
PIN. The PIN can be found on the WPS screen (AP Active PIN) or on a sticker on the back of the WTM652.
4. If the connection is successful, the Secure indicator stops flashing and remains lit. Otherwise, the Secure light continues to flash for up to two minutes (indicating that it is ready to accept a client connection) then turns off.
If the Secure light turns off, start again at step 1.
Note: When WPS is enabled, the WTM652 displays the status, network name, security type, encryption type, and passphrase at the bottom of the
WPS screen. If your client does not support WPS, use these settings to manually configure the client.
You have completed the basic configuration steps. Unless your cable operator requires additional configuration, which would be described in the information packet, you should now be able to access the Internet. If you want to further customize your configuration, proceed as follows:
•
•
•
If you have any problems, proceed to Troubleshooting .
Touchstone WTM652 Telephony Modem User’s Guide 44
Configuring the Firewall
to protect the computers on your home network from unwanted access. The firewall provides the following features:
• Virtual Server Support: if you have a server on your home network that you want to make available to the general Internet, you can configure a virtual server. The firewall passes requests from the Internet to the designated computer on your home network.
• Client filters: you can use client filters to block computers on your network from accessing the Internet (or certain services) during specific days and times.
• MAC Address filtering: allows access to the wireless network only by computers specifically authorized to connect.
• Ping blocking: ignores ICMP (Ping) requests from the Internet.
Proceed to the next page to begin configuring the firewall.
Configuring Virtual Servers
Follow these steps to allow outside access to servers on your internal network.
1 Click the Firewall link in the navigation menu, then click Virtual Servers.
The Virtual Servers window appears.
2 Proceed as follows:
If you want to… Then …
Add a well-known service
Choose the desired service from the Add drop-down menu and then click the Add button.
Add a custom service Fill in a row as follows:
• Description: the service name.
• Inbound port: the beginning and ending ports of the range required to support this service. These are the ports that outside clients use to access your serv er.
Touchstone WTM652 Telephony Modem User’s Guide 45
• Type: Choose TCP or UDP. If the service requires passing both TCP and UDP packets, you must create a second row.
• Private IP address: the IP address of the server on your internal network.
• Private port: the beginning and ending ports of the range required by this ser vice.
The private ports may be different from the
Inbound ports.
Enable or disable a service
Check (or clear) the box in the Enable column next to the service.
Remove a service Choose the row to remove in the Clear Entry drop-down menu and click the Clear button.
3 Click the Save button at the bottom of the page (you may need to scroll down) to save your changes.
4 Proceed to Configuring Client IP Filters .
Configuring Client IP Filters
Follow these steps to configure client IP filters.
1 Click the Firewall link in the navigation menu, then click Firewall Setting.
The Firewall Setting window appears.
2 Fill in the fields as follows:
• IP: the beginning and ending address in a range of IP addresses. To block only one address, use the same address twice.
• Port: the beginning and ending port in a range of ports. To block only one port, enter the same port twice.
• Type: choose one of TCP, UDP, or BOTH.
• Block Time: choose Always to set up a permanent block, or Block to specify days and times to block access.
Touchstone WTM652 Telephony Modem User’s Guide 46
• Day: choose the beginning and ending day of the week that this block is effective.
• Time: choose the beginning and end time of day that this block is effective.
• Enable: check this box to activate the block, or clear the check to disable the block.
3 Click the Save button to save your changes.
4 Proceed to Configuring MAC Address Filtering .
Configuring MAC Address Filtering
Follow these steps to configure MAC Address filtering.
1 Click the Firewall link in the navigation menu, then click MAC Address Filter ing.
The MAC Address Filtering window appears.
2 Click the Add button to add a blank row to the filter list.
3 Enter the MAC address of the computer you want to add to the filter. Do not enter colons or dashes in between the hex digits. For infor mation about find-
Touchstone WTM652 Telephony Modem User’s Guide 47
ing the MAC address of a computer, go to Setting the MAC Address
and see the sidebar.
Note: Make sure you enter the MAC address correctly. The Telephony
Modem may completely block access if you enter an incorrect address.
4 Click the Save button to save your changes.
5 Proceed to Configuring DDNS .
Configuring DDNS
The public IP addresses assigned to your Telephony Modem can change from time to time. If you are providing services from your private network (using the Virtual
Servers feature), you should use Dynamic DNS (DDNS) to associate your current
IP address with a domain name. The Telephony Modem directly supports several major DDNS providers.
After setting up a DDNS account, follow these steps to configure the Telephony
Modem to contact the DDNS provider.
1 Click the Firewall link in the navigation menu, then click DDNS.
The DDNS window appears.
Touchstone WTM652 Telephony Modem User’s Guide 48
2 Choose your DDNS provider from the DDNS Service drop-down menu.
3 Enter your DDNS account name, password, and DDNS domain name in the appropriate fields.
4 Click the Update DDNS button.
Note: Your domain name may not be immediately associated with your current IP address. Updated DNS information takes some time to propagate across the Internet.
Touchstone WTM652 Telephony Modem User’s Guide 49
Configuring RIP
Enabling RIP (Router Information Protocol) allows the WTM652 to act as a router in your local network. RIP is primarily intended for use in an office environment.
Requirements
To successfully configure RIP, you must:
• have a static IP address assigned by your cable provider
• disable Network Address Translation (NAT) on the WTM652 (which means you must either assign static IP addresses to all devices in your local network or use a DHCP server to assign addresses)
Action
Follow these steps to configure RIP.
1 Click the Lan Setup link in the navigation menu, then click RIP Settings.
The RIPv2 Settings window appears:
Touchstone WTM652 Telephony Modem User’s Guide 50
2 If NAT is enabled, choose Disable in the NAT Enable/Disable field at the bottom of the screen.
3 Select Enable from the RIP Enable/Disable menu.
4 If your routers need to authenticate to each other, choose the authentication type and enter an authentication key.
5 Click Save.
Touchstone WTM652 Telephony Modem User’s Guide 51
Configuring Your Ethernet Connection
If your computer is equipped with a LAN card providing an Ethernet connection, you may have to configure your computer’s TCP/IP settings. The steps that follow will guide you through setting your computer’s TCP/IP settings to work with the
Wideband Cable Modem.
Requirements
Make sure you have the following before attempting to configure your Ethernet connection:
• Computer with:
— one of: Windows XP, Windows Vista, Windows 7, or MacOS X
— Ethernet interface
• Ethernet cable (supplied)
• IP address, subnet, gateway, and DNS information for installations not using
DHCP
How to use this chapter
The following list shows the procedures for modifying the TCP/IP settings on the computer. The procedure is slightly different depending on the operating system that you are using. Please ensure you are using the correct steps for the operating system on your computer. Follow the links below for instructions to configure your ethernet connection on your operating system.
•
TCP/IP Configuration for Windows XP
•
TCP/IP Configuration for Windows Vista
•
TCP/IP Configuration for Windows 7
•
TCP/IP Configuration for MacOS X
Touchstone WTM652 Telephony Modem User’s Guide 52
TCP/IP Configuration for Windows XP
Follow these steps to configure the TCP/IP settings on a Windows XP operating system.
Note: Dialog boxes shown on your computer may differ slightly from those shown in this procedure.
1 From the computer, select Start > Settings > Control Panel and double click on the Network Connections icon in the Control Panel.
2 Click the Configuration tab in the Network window to display the list of
Network Adapters.
Touchstone WTM652 Telephony Modem User’s Guide 53
3 Highlight TCP/IP by clicking on it one time, then click on Properties.
4 Click the IP Address tab, click Obtain an IP address automatically, then click OK.
5 Click OK to accept the new settings, and OK again to close the Configuration window.
6 You may have to restart your computer in order for your computer to obtain a new IP address from the network.
Touchstone WTM652 Telephony Modem User’s Guide 54
TCP/IP Configuration for Windows Vista
Follow these steps to configure the Ethernet interface for use with Touchstone products.
1 Open the Vista Control Panel.
2 Double-click Network and Sharing Center.
Touchstone WTM652 Telephony Modem User’s Guide 55
3 Click Manage network connections. If prompted for a connection, choose
Local Area Connection.
4 Double-click the Local Area Connection to open the Status window:
5 If Windows requests permission to continue, click Continue.
6 Click Properties.
Touchstone WTM652 Telephony Modem User’s Guide 56
7 Double-click Internet Protocol Version 4 (TCP/IPv4).
8 Select Obtain an IP address automatically and Obtain DNS server
address automatically, unless instructed otherwise by your cable provider.
9 Click OK to close the Properties windows.
Touchstone WTM652 Telephony Modem User’s Guide 57
TCP/IP Configuration for Windows 7
Follow these steps to configure the Ethernet interface for use with Touchstone products.
1 Open the Windows 7 Control Panel.
2 Click Network and Internet.
Touchstone WTM652 Telephony Modem User’s Guide 58
3 Click Network and Sharing Center.
4 Click Local Area Connection to open the Status window.
Touchstone WTM652 Telephony Modem User’s Guide 59
5 Click Properties to open the Properties window.
TCP/IPv4 Properties TCP/IPv6 Properties
Touchstone WTM652 Telephony Modem User’s Guide 60
6 Select Internet Protocol Version 4 (TCP/IPv4) and click Properties to configure TCP/IPv4.
Note: If your cable provider requires TCP/IP version 6, select Internet Pro-
tocol Version 6 (TCP/IPv6) and click Properties to configure TCP/IPv6.
The TCP/IP properties window for the version you selected displays.
TCP/IPv4 Properties TCP/IPv6 Properties
7 For either TCP/IPv4 or TCP/IPv6, select Obtain an IP address automati-
cally and Obtain DNS server address automatically, unless instructed otherwise by your cable provider.
8 Click OK to accept the new settings and close the Properties windows and then click Close to back out of the remaining setup screens.
Touchstone WTM652 Telephony Modem User’s Guide 61
TCP/IP Configuration for MacOS X
Follow these steps to configure the Ethernet interface for use with Touchstone products.
1 Open System Preferences, either by choosing System Preferences from the
Apple menu or by clicking the System Preferences icon in the dock.
2 Click the Network icon.
Touchstone WTM652 Telephony Modem User’s Guide 62
3 Choose Automatic from the Location drop-down menu, and Built-in Eth-
ernet from the Show menu.
4 Choose the TCP/IP tab, if necessary.
5 Choose Using DHCP from the Configure IPv4 menu.
6 If necessary, click the Renew DHCP Lease button.
7 Close the System Properties application.
Touchstone WTM652 Telephony Modem User’s Guide 63
Powe
DS r
U
S
O nl ine
Link
1
LAN
2
LAN
LA
N 3
N 4
LA
W
LA
N e
Se cur
1 one
Teleph
Tel ep hon e 2
TM
Tou ch sto ne ny
Te le pho
Modem
Using the Telephony Modem
This chapter describes the controls and features available on the Touchstone Telephony Modem, and covers basic troubleshooting procedures.
•
Setting up Your Computer to Use the Telephony Modem
•
Indicator Lights for the WTM652A/B Models
•
Indicator Lights for the WTM652G Model
•
Setting up Your Computer to Use the Telephony
Modem
Follow the instructions in the information packet supplied by your cable company.
Contact your cable company if you need help setting up your computer.
Indicator Lights for the WTM652A/B Models
The Touchstone Telephony Modem has 13 LED indicator lights to assist in troubleshooting.
Wiring Problems
If the Telephony Modem begins flashing all its lights for more than 10 seconds, this indicates a problem with the telephone wiring — the red and green wires may be shorted (touching), or there may be undesired voltage on the lines. If this pattern persists for more than 10 seconds, disconnect the telephone lines from the Telephony Modem, then call a wiring technician for assistance.
Touchstone WTM652 Telephony Modem User’s Guide 64
Patterns: Normal Operation (WAN)
The following table shows light patterns for the cable connection during normal operation.
Mode Power DS US Online
AC Power
No AC Power
Firmware
Upgrade
On
Off
On
On =
Connected to the
Internet
Flash = Not connected to the
Internet
Off
Flash
On =
Connected to the
Internet
Flash = Not connected to the
Internet
Off
Flash
On =
Internet
Available
Off =
Internet not available
Off
On
Link
On =
Computer
Connected
Off =
Computer not
connected
Flash =
Computer
Activity
Off
(normal
operation)
Touchstone WTM652 Telephony Modem User’s Guide 65
Patterns: Normal Operation (LAN and telephone)
The following table shows light patterns for the Ethernet and wireless LANs, and the telephones, during normal operation.
Mode
AC Power
LAN1 - LAN4 WLAN
On = Computer
Connected
Off = Computer not connected
Off = Computer not connected
Flash = Computer
Activity
On = Computer
Connected
Flash = Com puter
Activity
Tel. 1/Tel. 2
On = On-hook
Flash = Off-hook
Off = disabled
Off Off Off No AC Power
Firmware Upgrade (normal operation) (normal operation) (normal operation)
Touchstone WTM652 Telephony Modem User’s Guide 66
Secur e
Indicator Lights for the WTM652G Models
The Touchstone Telephony Modem has fourteen LED indicator lights to assist in trouble shooting.
Wiring Problems
If the Telephony Modem begins flashing all its lights for more than 10 seconds, this indicates a problem with the telephone wiring — the red and green wires may be shorted (touching), or there may be undesired voltage on the lines. If this pattern persists for more than 10 seconds, disconnect the telephone lines from the Telephony Modem, then call a wiring technician for assistance.
Patterns: Normal Operation (LAN and Telephone)
The following table shows light patterns for the Ethernet and wireless LANs, and the telephones, during normal operation.
Mode
AC Power
LAN1 - LAN4
On = Computer
Connected
Off = Computer not connected
Flash = Computer Activity
WLAN
On = Computer
Connected
Off = Computer not connected
Flash =
Computer Activity
Tel. 1/Tel. 2
On = On-hook
Flash = Off-hook
Off = disabled
No AC Power Off Off
Firmware Upgrade (normal operation) (normal operation)
On = On-hook
Flash = Off-hook
Off = disabled
Off
Touchstone WTM652 Telephony Modem User’s Guide 67
Patterns: Normal Operation (WAN and Battery)
The following table shows light patterns during normal operation.
Mode
AC
Power
Good
No AC
Power
Battery
Installed
Power
On
Flash
DS
On =
Connected to the
Internet
Flash =
Not
connected to the
Internet
On =
Connected to the
Internet
Flash =
Not
connected to the
Internet
On =
Internet available
Off =
Internet not
available
Off
US
Off
Online
Off
Link
On =
Computer connected
Off =
Computer not
connected
Flash =
Computer activity
Off
Battery
On =
Battery good or low
Off =
Battery missing
Flash =
Battery bad
Off =
Battery power
Flash =
Battery bad
No AC
Power
No
Battery
Firmware
Upgrade
Off
On
Off
Flash
Off
Flash
Off
On
Off Off
(normal operation)
(normal operation)
Touchstone WTM652 Telephony Modem User’s Guide 68
Patterns: Startup Sequence
The following table shows the Telephony Modem light patterns during each phase of the startup sequence. There are two phases of startup; the Telephony phase and the cable modem phase. Both are outlined below.
Power,
DS, US,
Online
Off
Link
Off
Telephone
1
Off
2
Off
Battery*
Off
Description
No power to Cable Modem
Flash Flash Flash Flash Flash Power-on Self Test
See “Cable Modem Start Up Sequence” Below
On
On
On
On
Flash
Off
Off
Flash
Off
Off
Retrieving telephone network information
Retrieving telephone line information
On On Flash Flash Off
Activating telephone
service
Normal Operation
* = Battery LED only applies to those models with battery backup
Touchstone WTM652 Telephony Modem User’s Guide 69
TM Reset
Cable Modem Start Up Sequence
DS
Flash
On
US
Off
Flash
Online
Off
Off
On On Flash
Link
Off
Off
Off
Description
Downstream search
Downstream found; upstream search
Downstream and Upstream found; retrieving setup information from cable operator
Router Reset
Using the Reset Buttons
Use the Router Reset button to reset the Ethernet and wireless connections without affecting the cable or telephony connections. You may need to reset the router if you are having problems connecting to the Internet, but the phones are working.
To reset the Telephony Modem to factory defaults, hold the Router Reset button for about 8 seconds.
Use the TM Reset button to reset the mo dem as if you power cycled the entire unit. The phones will be out of service until the Telephony Modem finishes reconnecting to the cable system. You may need to reset the Telephony Modem if you are having problems connecting to the Internet or with the phones. This button should be used rarely.
The TM Reset button is recessed to prevent accidental resets. Use a pointed nonmetallic object to press this button.
The diagram to the left shows the location of the Reset buttons.
Touchstone WTM652 Telephony Modem User’s Guide 70
Troubleshooting
The information in this chapter may help you to clear up common problems.
Viewing Connection Information
The web-based configuration interface provides screens that can help to trouble shoot connectivity problems. The default IP address of the Telephony Modem is
192.168.2.1 — if you have changed the IP address, remember to enter the changed address in your browser.
Viewing the DHCP Client List
The DHCP client list shows all computers that are currently connected to the Telephony Modem and have received an IP address from the router. This information can help you to troubleshoot connectivity problems or to see whether other people have connected to an unsecured network.
To view the list, choose LAN Setup from the navigation menu and then DHCP Cli ent List.
The list shows the IP address assigned to each computer, the host name (the name given by the computer’s owner), and the MAC address of that computer. Click the
Refresh button to update the listing.
Note: The DHCP client list does not show devices that have manually assigned
IP addresses.
Touchstone WTM652 Telephony Modem User’s Guide 71
Viewing the Security Log
The security log keeps a list of system- and firewall-related events. You can use the security log to troubleshoot connectivity problems and to view possible intrusion attempts.
To view the security log, choose Firewall from the navigation menu and then Se curity Log.
Click the Refresh button to update the listing. Click the Save button to download the current log to your computer (the file is named log_web.txt). Click the button to clear both the system and firewall logs.
Note: You may have to scroll down to access the buttons.
Touchstone WTM652 Telephony Modem User’s Guide 72
Backing Up and Restoring the Configuration
You can save a copy of the current Telephony Modem router configuration to a local computer. Once you have configured the Telephony Modem as desired, you should back up the configuration so that you can restore it later if needed.
Backing Up
Follow these steps to back up the configuration.
1 Click the Utilities link in the navigation menu, then click Save/Backup Settings.
The Save/Backup Settings window appears.
2 Click the Save button.
The Telephony Modem downloads a file called admcfg.cfg to your computer.
3 Copy the admcfg.cfg file to a safe location. You can rename the file, if desired, to help you find it in the future.
Restoring
Follow these steps to restore a previous configuration.
1 Click the Utilities link in the navigation menu, then click Restore Previous-
Settings.
The Restore Previous Settings window appears.
2 Click the Choose File button.
Your browser prompts you to find the saved configuration file.
3 After locating the saved configuration file, click the Restore button.
The Telephony Modem restarts the router with the restored configuration.
Touchstone WTM652 Telephony Modem User’s Guide 73
Resetting the Telephony Modem Router
The router can be reset in two ways: a “normal” reset that simply restarts the rout er (without affecting any phone calls in progress), and a “factory” reset that erases the current configuration to the factory defaults.
Restarting the Router
To restart the router, you can push the Router Reset button on the back of the
Telephony Modem. If your Telephony Modem is mounted in an inconvenient location, or you need to restart it remotely, you can use the Restart Router page.
To restart the router remotely, click the Utilities link in the navigation menu, then click Restart Router. When the page appears, click the Restart Router button. The
Telephony Modem shows a confirmation dialog; click OK to restart the router.
Resetting the Router to Factory Defaults
To reset the router to factory defaults, you can press and hold the Router Reset but ton on the back of the Telephony Modem for about eight seconds. You may need to do this if a misconfiguration has locked out all access. If you can access the router and want to restart it remotely, you can use the Restore Factory Defaults page.
To restore factory defaults remotely, click the Utilities link in the navigation menu, then click Restore Factory Defaults. When the page appears, click the Restore Defaults button. The Telephony Modem shows a confirmation dialog; click OK to erase the configuration to factory defaults.
The router resets itself after erasing the current configuration.
Note:
first.
Touchstone WTM652 Telephony Modem User’s Guide 74
General Problems and Solutions
The Telephony Modem is plugged in, but the Power light is off.
Check all power connections. Is the power cord plugged in firmly at both ends?
If you plugged the power cord into a power strip, make sure the strip is switched on.
Avoid using an outlet controlled by a wall switch, if possible.
Finally, check the fuse or circuit breaker panel.
I’m not getting on the Internet (all connections).
It may take over 30 minutes to establish a connection the first time you power up your Telephony Modem, especially when many people are online.
Always leave your Telephony Modem plugged into AC power and connected to the cable system.
Check the front panel lights:
• The Power and Online lights should be on.
• The Link light should be either on or blinking.
• If the Power light blinks for more than 30 minutes, call your cable company for assistance.
Check your cable connections. Connectors should be finger-tight. The coax cable
should not be pinched, kinked, or bent sharply—any of these can cause a break or short in the cable (you may have to replace the cable). If you have one or more splitters between the Telephony Modem and CATV outlet, remove the splitters and connect the Telephony Modem directly to the outlet.
Proceed to the Ethernet or wireless solutions (next page) if necessary.
Touchstone WTM652 Telephony Modem User’s Guide 75
I’m not getting on the Internet. (Ethernet)
If you are using a hub, is the hub turned on?
Are you using the right type of Ethernet
cable? Use the supplied cable for direct connection to a computer; use a cross-over cable for connection to a hub.
Press the Router Reset button on the back of the Telephony Modem.
A misconfiguration could lock out all access to the Telephony Modem router.
If you think this has happened, see Resetting the Router to Factory Defaults .
I’m not getting on the Internet. (Wireless)
Check the indicator lights (see Using the Telephony Modem ) — the WLAN
light should be on.
Does your connection utility discover your wireless LAN? If you turned off
“Broadcast SSID” (see Configuring the LAN Channel and Name ) you need to
manually enter the name of your wireless LAN in the connection utility.
Change your security mode to “WEP” or “disabled” (see Configuring Wireless
Security ). If you use “disabled,” enable one of the other security modes as
soon as you find the problem.
A misconfiguration could lock out all access to the Telephony Modem router.
If you think this has happened, see Resetting the Router to Factory Defaults .
My wireless Internet connection stops working sometimes.
This is usually caused by interference — two common sources are 2.4GHz
“remote” telephones and microwave ovens. If you cannot remove the inter-
fering product, try using a different channel or setting Protected Mode (see
Configuring the LAN Channel and Name
for both features).
I can get on the Internet, but everything is slow.
If the Web site you are visiting is very popular, that site may be having trouble servicing all the requests. If other sites download quickly, wait for a few minutes and try again. Usage during peak hours may also affect the con nection speed.
Other communications on the LAN, or interference with wireless connections, may slow down your connection.
Touchstone WTM652 Telephony Modem User’s Guide 76
I don’t have dial tone when I pick up my phone, why?
In order for telephone service to be functional on the Telephony Modem, telephone service must have been purchased from the service provider and configured on your Telephony Modem. The following steps should help in identifying the source of the problem.
1 Is the Power LED lit?
• If not, check to make sure the Telephony Modem is plugged in and the outlet has power.
• If the LED is lit, go to the next step.
2 Is the Online LED lit?
• If not, check the coax connection at the Telephony Modem and the wall. Ensure they are connected and tight. If they are and you do not have dial tone, contact your service provider.
• If the Online LED is lit, go to the next step.
3 Is the Telephone (Telephone 1 or Telephone 2) LED lit?
• If not, phone service has not been set up on that line. Contact your service provider.
• If it is blinking, there is a phone off hook somewhere in the house. Find that phone and hang it up.
• If it is lit, go to the next step.
4 Is the phone plugged directly into the Telephony Modem?
• Make sure the phone is plugged into the port on the back of the
Telephony Modem labeled “Tel 1” for line 1, and “Tel 2” for line 2.
• If so, try a different phone. Make sure the new phone is a working phone.
• If a known good phone is used and you still don’t have dial tone, try a different phone cable. If a new phone and cable do not restore dial tone, call your service provider.
Touchstone WTM652 Telephony Modem User’s Guide 77
5 Is the Telephony Modem plugged into a wall outlet?
• If so, unplug the RJ-11 connector at the back of the Telephony
Modem and plug in a known working phone. If you now have dial tone, the problem is with the house wiring. Contact your cable company or a qualified wiring technician to correct the house wiring. If you still do not have dial tone, contact your service provider.
Touchstone WTM652 Telephony Modem User’s Guide 78
Glossary
The following is a list of common cable and networking terms.
Amp-hour (Ah)
A measure of battery capacity. For example, a 1.0Ah battery can nominally supply one Ampere of current for one hour.
Category 5 (Cat5)
A high-quality type of cable, used for Fast Ethernet (100BaseT) connec tions.
When purchasing Ethernet cables, always look for Category 5 cable.
Coaxial cable (coax)
A thin wire, used to connect your television and Telephony Modem to the cable TV system. You can buy coax from any electronics retailer and many discount stores.
CPE
Customer Premise Equipment. This is the equipment that is plugged in to the
Telephony Modem; typically a computer or hub.
Cross-over
An Ethernet cable used to connect two hubs (or a hub and a cable modem) together. Also, some Ethernet hubs may have built-in cross-over on one or more ports (which eliminates the need for a cross-over cable).
DHCP
Dynamic Host Configuration Protocol. An IP protocol used to provide an IP address and location of services (such as DNS and TFTP) needed by a device connecting to the network. DHCP allows the cable company to con figure your computer’s networking software for you.
DNS
Domain Name Service (Server). An IP service that associates a domain name (such as www.example.com) with an IP address.
Touchstone WTM652 Telephony Modem User’s Guide 79
Downstream
In an HFC network, the direction from the head-end to the subscriber. Some older cable documentation may refer to this as the forward path.
DOCSIS
Data Over Cable System Interface Specification. The interoperability standards used for data communications equipment on an HFC network.
EMTA
Embedded Multimedia Terminal Adapter. An MTA device that is integrated with a cable modem.
Ethernet
A standard method of connecting two or more computers into a Local Area
Network (LAN).
EuroDOCSIS
The European version of DOCSIS.
Event
An informational message used for monitoring network status.
F-connector
The type of connector used on coax cable. There are two common types of
F-connector, slip-on and screw-on. Use coax with screw-on connectors for connecting your Telephony Modem.
Firewall
A hardware or software device that prevents unauthorized access to a private network from the Internet. The WTM652 provides a built-in firewall.
Gateway
The device, usually a router, that connects devices on a given IP subnet to other IP subnets.
Touchstone WTM652 Telephony Modem User’s Guide 80
Headend
The “central office” in an HFC network. The headend houses both video and data equipment. In larger cable networks, a “master” headend often feeds several “remote” headends to provide distributed services.
HTTP
HyperText Transfer Protocol.
Hub
A box with several Ethernet connectors. Ethernet hubs provide a common point of contact for all connected devices.
IP address
A number assigned to your computer by your cable company, used to identify your computer to other systems on the Internet.
ISDN
Integrated Services Digital Network. A digital telephony standard that provides communication speeds about twice as fast as standard dialup.
LAN
Local Area Network. A network that allows computers in a single location
(such as a building) to communicate with one another.
LED
Light Emitting Diode. A semi-conductor diode that emits light when current is passed through it.
MAC address
A number that uniquely identifies any device connected to a network. Your cable company uses your Telephony Modem’s MAC address to authorize access to the Internet. The MAC address is printed on a label on the bottom of your Telephony Modem.
Protocol
A set of rules and formats that determines the communication behavior of network entities at a given layer.
Touchstone WTM652 Telephony Modem User’s Guide 81
Proxy
A device or program that stands in between a server (for example, a web site) and a client (your browser), providing a way to relieve some of the burden from the server. For example, your cable company may have a web proxy that keeps copies of popular web pages; the proxy can send you those pages instead of fetching them directly from the web site, resulting in faster page loading and less network congestion.
RF
Abbreviation for Radio Frequency. Some literature refers to coax as “RF cable” and the connectors as “RF connectors.”
RJ-11
A standard 4-pin modular connector, commonly used in North America for connecting telephones.
RJ-45
A standard 6-pin modular connector, commonly used on Ethernet cable. An
RJ-45 connector looks like a wide RJ-11 (telephone) connector.
Splitter
A small box with three cable connectors: one input and two outputs. You may need a splitter if you have a TV already connected to the cable outlet that you want to use for your Telephony Modem. You can buy a splitter from any electronics retailer and most discount stores.
SSID
Service Set IDentifier, a string of text (up to 32 characters long) that uniquely identifies a wireless LAN.
Switched outlet
A power outlet that may be turned on and off using a wall switch. Usually intended for lamps. Avoid plugging your computer or Telephony Modem into a switched outlet to avoid disruptions.
TCP/IP
Transmission Control Protocol/Internet Protocol. The protocols used to facilitate communications across one or more connected networks.
Touchstone WTM652 Telephony Modem User’s Guide 82
TDMA
Time Division Multiple Access. A method used by DOCSIS-compliant cable modems for sending upstream data with minimal interference.
Upstream
The path from a subscriber device to the headend. Some older cable documentation may refer to this as the return path or reverse path.
WEP
Wired Equivalent Privacy, a common standard for encrypting data sent over a wireless LAN.
WPA
Wi-fi Protected Access, a standard for encrypting data sent over a wireless
LAN. WPA offers improved security over WEP.
Touchstone WTM652 Telephony Modem User’s Guide 83
Touchstone® WTM652 Telephony Modem User’s Guide
About Your New Telephony Modem
Battery Installation and Removal (WTM652G only)
Basic Backup Battery Installation
Extended Backup Battery Installation
Maximum Backup Battery Installation
Basic and Extended Backup Battery Removal
Maximum Backup Battery Removal
Installing and Connecting Your Telephony Modem
Selecting an Installation Location
Factors Affecting Wireless Range
Connecting the Telephony Modem
Configuring Your Wireless Connection
Accessing the Configuration Interface
Setting Up Your WAN Connection
Configuring the LAN Channel and Name
Configuring Wi-fi Protected Setup (WPS)
Configuring MAC Address Filtering
Configuring Your Ethernet Connection
TCP/IP Configuration for Windows XP
TCP/IP Configuration for Windows Vista
TCP/IP Configuration for Windows 7
TCP/IP Configuration for MacOS X
Setting up Your Computer to Use the Telephony Modem
Indicator Lights for the WTM652A/B Models
Patterns: Normal Operation (WAN)
Patterns: Normal Operation (LAN and telephone)
Indicator Lights for the WTM652G Models
Patterns: Normal Operation (LAN and Telephone)
Patterns: Normal Operation (WAN and Battery)
Viewing Connection Information
Backing Up and Restoring the Configuration
Resetting the Telephony Modem Router
Resetting the Router to Factory Defaults
General Problems and Solutions
Touchstone®
WTM652 Telephony Modem
User’s Guide
Copyright © 2009-2013 ARRIS. All rights reserved.
The information in this document is subject to change without notice. The statements, configurations, technical data, and recom mendations in this document are believed to be accurate and reliable, but are presented without express or implied warranty. Users must take full responsibility for their applications of any products specified in this document. The information in this docu ment is proprietary to
ARRIS.
ARRIS, Touchstone, and the ARRIS logo are trademarks or registered trademarks of ARRIS Group. All other trademarks and reg istered trademarks are the property of their respective holders.
Protected under one or more of the following U.S. patents:
7,031,435; 7,100,011. Other patents pending.
ARSVD01202
Release 6 Standard 1.2 June 2013
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement