MINI-COMPACT
RADIO DATA SYSTEM
MAX-N72/N73/N75
Instruction Manual
Downloaded From Disc-Player.com Samsung Manuals
Safety Warnings
GB
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE REAR COVER.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified
as a CLASS 1 LASER product.
Use of controls, adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
CAUTION-INVISIBLE LASER RADIATION WHEN OPEN
AND INTER LOCKS DEFEATED, AVOID
EXPOSURE TO BEAM.
This symbol indicates that dangerous voltage
which can cause electric shock is present inside
this unit.
This symbol alerts you to important operating
and maintenance instructions accompanying the
unit.
WARNING: To reduce the risk of fire or electric shock,
do not expose this appliance to rain or
moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
Wiring the Main Power Supply Plug(UK Only)
IMPORTANT NOTICE
The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be
used.
Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must
be of the same colour as the fuse fitted in the plug. Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power
point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do
not connect the plug to a main socket as there is a risk of shock hazard from the bared flexible cord.
Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times.
IMPORTANT
The wires in the main lead are coloured in accordance with the following code:–
BLUE = NEUTRAL
BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug,
proceed as follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE
or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or
coloured BROWN or RED.
WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS
MARKED WITH THE LETTER E OR BY THE EARTH SYMBOL
, OR
COLOURED GREEN OR GREEN AND YELLOW.
Downloaded From Disc-Player.com Samsung Manuals
Thank you for buying this
SAMSUNG mini-compact system.
Contents
Please take time to read these instructions.
They will allow you to operate your
system with ease and take full advantage
of its features.
SAFETY WARNINGS .................................................................................................................................................................................. 2
INSTALLING YOUR MINI-COMPACT SYSTEM
Front Panel View ...................................................................................................................................................................................... 4
Remote Control ........................................................................................................................................................................................ 5
Rear Panel View ...................................................................................................................................................................................... 6
Where to Install Your Mini-Compact System ............................................................................................................................................ 7
Connecting your System to the Power Supply ........................................................................................................................................ 7
Connecting the Loudspeakers.................................................................................................................................................................. 7
Connecting the AM(MW)/LW Aerial .......................................................................................................................................................... 8
Connecting the FM Aerial ........................................................................................................................................................................ 8
Inserting Remote Control Batteries...................................................................................................................................................... 9
Viewing the Various Functions on Your System ........................................................................................................................................ 9
Moving Jog Function ................................................................................................................................................................................ 9
Setting the Clock ...................................................................................................................................................................................... 10
CD-PLAYER
Loading and Changing Compact Discs.................................................................................................................................................... 10
Listening to a Compact Disc .................................................................................................................................................................... 11
Selecting a Disc in the CD changer ........................................................................................................................................................ 11
Selecting a Track ...................................................................................................................................................................................... 11
Searching for a Specific Music Passage on a CD .................................................................................................................................. 12
Shuffle Function ...................................................................................................................................................................................... 12
Repeating One or All Tracks on the Compact Discs ............................................................................................................................ 12
Programming the Order of Playback ........................................................................................................................................................ 12
Checking or Changing Programmed Tracks ............................................................................................................................................ 13
TUNER
Searching for and Storing the Radio Stations ........................................................................................................................................ 14
Selecting a Stored Station........................................................................................................................................................................ 14
Improving Radio Reception...................................................................................................................................................................... 14
About RDS broadcasting.......................................................................................................................................................................... 15
About RDS Display function .................................................................................................................................................................... 15
TPY (Program Type) indication and PTY-SEARCH function.................................................................................................................... 16
TAPE DECK
Listening to a Cassette ............................................................................................................................................................................ 17
CD Synchro Record Feature.................................................................................................................................................................... 17
Recording a Compact Disc ...................................................................................................................................................................... 17
Recording a Radio Programme................................................................................................................................................................ 18
Copying a Cassette (Dubbing) ................................................................................................................................................................ 18
Selecting the Cassette Playback Mode.................................................................................................................................................... 18
Tape Counter............................................................................................................................................................................................ 19
Dolby Noise Reduction System (Only MAX-N75) .................................................................................................................................... 19
Counter Display (Only MAX-N73/N72) .................................................................................................................................................... 19
OTHER FUNCTIONS
Timer Function ........................................................................................................................................................................................ 20
Cancelling the Timer ................................................................................................................................................................................ 21
Mute Function .......................................................................................................................................................................................... 21
Power Sound/Surround Function ............................................................................................................................................................ 21
Super Bass System (SBS) ...................................................................................................................................................................... 21
User EQ Setting ...................................................................................................................................................................................... 22
Selecting an Equalizer Preset .................................................................................................................................................................. 22
3D Surround Function .............................................................................................................................................................................. 22
Game Function ........................................................................................................................................................................................ 23
Connecting Headphones...................................................................................................................................................................... 23
Connecting to an External Source .......................................................................................................................................................... 24
CD Digital Out Jack.................................................................................................................................................................................. 24
RECOMMENDATIONS FOR USE
Safety Precautions .................................................................................................................................................................................. 24
Cleaning Your Mini-Compact System ...................................................................................................................................................... 25
Precautions When Using Compact Discs ................................................................................................................................................ 25
Precautions When Using Audio Cassettes .............................................................................................................................................. 25
Before Contacting the After-Sales Service .............................................................................................................................................. 25
Technical Specifications .......................................................................................................................................................................... 26
Symbols
Downloaded From Disc-Player.com Samsung Manuals
Press
Push
Important
Note
GB
Front Panel View
GB
37
1
2
3
4
5
Disc Change
Disc 1
Disc 2
Open/
Close
Disc 3
36
35
On/Standby
Aux
6
34
Volume
+
Game
Demo
33
PTY
RDS
Display
–
Timer/
Clock
Band
7
8
9
ower
Surround
TUNER
CD
TAPE
Deck 1/2
Mono/ST
Program
Counter Reset
Preset/Memory
31
Phones
Rev Mode
CD Repeat
S.BASS
Dubbing
10
32
Normal
CD REC/Pause
REC/Pause
Shuffle
30
EQ
CD Synchro
3D Surround
High
11
12
29
28
27
26
25
24
13
14
23
15
22
16
21
Manual EQ
/Enter
20
19
18
Do
wn
Preset/Manual
Up
17
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Disc Selection Buttons
PTY (RDS)
Demo
Game
On/Standby
Aux
Headphone Jack Connector
Display (RDS)
Timer/Clock
Rev Mode
Counter Display (MAX-N73/N72)
Dolby NR (MAX-N75)
12. Cassette Deck 1
13. Dubbing Normal/CD REC/Pause
14. Dubbing High
15 Counter Reset
16. Deck 1/2
17. Preset/Manual or Stop Button
Downloaded From Disc-Player.com
Samsung
Manuals
18. CD Track
or Radio
Station Search (Down/Up)
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
Moving Jog
Manual EQ/Enter
REC/Pause
Preset Memory
Mono/ST
Shuffle
Cassette Deck 2
CD Synchro
CD Repeat
Program
3D Surround
EQ
S. Bass
Power Surround
Volume
Function Selection Buttons.
Disc Change
Open/Close
Compact Disc Compartment
Remote Control
GB
20
Power
Timer
Mute
On/Off
1
2
19
Sound
Mode
Disc Skip
18
Program
/Set
Aux
3
17
Deck 1/2
4
Repeat
Mono/ST.
Tuner
CD
Band
5
TAPE
6
16
15
14
13
CD
12
7
8
VOL.
11
CD
9
Tuning
Mode
10
CD
VOL.
1.
On/Standby
11. CD Track or Radio Station Search
2.
Disc Number Skip
12. CD Play and Pause
3.
Sound Mode
13. Deck Stop
4.
Deck 1/2
14. Deck Play
5.
CD Repeat
15. Mono/ST Selection
6.
Tape Rewind and Fast-Forward
16. Frequency Band Selection
7.
CD Stop
17. AUX
8.
Volume Increase
18. Program/Set
9.
Volume Decrease
19. Mute
10. Tuning Mode
Downloaded From Disc-Player.com Samsung Manuals
20. Timer On/Off
Rear Panel View
GB
1
DIGITAL OUT
OPTICAL
FM ANT. (75Ω)
2
AM ANT
3
4
(IMPEDANCE 6Ω)
5
1. CD Digital out Jack
2. FM Aerial Connector Terminal
3. AM(MW)/LW Aerial Connector Terminal
4. Aux-Input
5. Loudspeaker Connector Terminal
Downloaded From Disc-Player.com Samsung Manuals
Where to Install Your
Mini-Compact System
Connecting the Loudspeakers
GB
To take full advantage of your new mini-compact system, follow
these installation instructions before connecting the unit.
Install the system on a flat, stable surface.
Never place this unit on carpeting.
Never place this unit in an outdoor area.
Maintain an open space of approximately 4 inches (10 cm) on the
sides and rear of the system, for ventilation purposes.
Make sure that you have enough room to open the compact disc
compartment easily.
Place the loudspeakers at a reasonable distance on either side of the
system to ensure good stereo sound.
Direct the loudspeakers towards the listening area.
For optimum performance, make sure that both speakers are placed
at an equal distance above the floor.
The loudspeaker connector terminals are located on the rear
of the system.
There are four terminals on the system:
Two for the left speaker (marked L)
Two for the right speaker (marked R)
To achieve the correct sound quality, connect the:
Red wire to the + terminals
Black wire to the - terminals
1
2
3
Disc Change
Disc 1
Disc 2
Open/
Close
Disc 3
On/Standby
Insert the wire, up to the plastic sheathing, in the hole.
Push the tab back:
To the left on the system, until it clicks into place
To the top on the loudspeaker
Result: The wire is pinched and held firmly in place.
Volume
+
Game
Aux
To connect a wire to a terminal, push the tab as far as it will go:
To the right on the system
4
Demo
PTY
RDS
Display
Repeat the operation for each wire.
–
Timer/
Clock
Band
ower
Surround
TUNER
CD
Moving Control
Rev Mode
TAPE
Manual EQ /Enter
Deck 1/2
Mono/ST
Counter Reset
Preset/Memory
Program
CD Repeat
S.BASS
Dubbing
Shuffle
REC/Pause
High
wn
Do
Normal
CD REC/Pause
Preset/Manual
Up
CD Synchro
EQ
<MAX-N72>
3D Surround
L
R
Connecting your System to the
Power Supply
<MAX-N73>
The main lead must be plugged into an appropriate socket.
Before plugging your system into a main socket, you must check
the voltage.
L
R
1
2
Plug the main lead (marked AC Cord on the rear of the system) into
an appropriate socket.
Press the On/Standby button to switch your mini-compact system on.
(IMPEDANCE 6Ω)
<MAX-N75>
L
R
Downloaded From Disc-Player.com Samsung Manuals
Connecting the AM(MW)/LW Aerial
Connecting the FM Aerial
GB
The AM aerial (for long and medium waves) can be:
Placed on a stable surface
Fixed to the wall (you must first remove the base)
The AM aerial connector terminals are located on the rear of the system and
are marked AM .
To avoid noise interference, check that the loudspeaker wires do
not run close to the aerial wires.
Always keep them at least 2 inches (5 cm) away.
DIGITAL OUT
OPTICAL
How to connect a COAXIAL TYPE aerial.
Connect a 75Ω antenna to the FM antenna terminal.
Plug the connector on the FM aerial supplied into the coaxial socket
(75Ω) marked FM on the rear of the system.
Follow the instructions given on Page 14 to tune into a radio station, and determine the best position for the aerial.
If reception is poor, you may need to install an outdoor aerial.
To do so, connect an outdoor FM aerial to the FM socket on the rear
of the system using a 75Ω coaxial cable (not supplied).
FM ANT. (75Ω)
AM ANT.
FM
FM AERIAL
(supplied)
Downloaded From Disc-Player.com Samsung Manuals
FM
75Ω COAXIAL CABLE
(not supplied)
Inserting Remote Control Batteries
Moving Jog Function
GB
Insert or replace remote control batteries when you:
Your mini-compact system has an improved Moving Jog Function,
including visual effect on standard jog function.
Each time you press Tuner, CD or Tape buttons, Moving Jog will
move automatically to a selected function.
Moving Jog will always return to CD position at standby.
Be cautious not to move Moving Jog excessively or give extreme
force. It will likely be the major cause of malfunction.
Purchase the mini-compact system
Find that the remote control is no longer operating correctly
When replacing the batteries, use a new set of batteries and
never mix alkaline and manganese batteries.
1
Place your thumb on the position marked
on the battery compartment cover (rear of the remote control) and push the cover in the
direction of the arrow.
–
Timer/
Clock
Band
TUNER
2
Insert two AAA, LR03 or equivalent batteries, taking care to respect
the polarities:
+ on the battery against + on the remote control
– on the battery against - on the remote control
Rev Mode
Mono/ST
Counter Reset
Preset/Memory
Dubbing
Replace the cover by sliding it back until it clicks into position.
Normal
CD REC/Pause
Viewing the Various Functions on
Your System
You can view the various functions available on your system.
1
Press the Demo button.
Result: The various functions available are listed in turn on the display.
All these functions are described in detail in this booklet.
For instructions on how to use them, refer to the appropriate sections.
2
To cancel this function, press Demo again.
On/Standby
Volume
+
Game
Aux
Demo
PTY
RDS
Display
–
Timer/
Clock
Band
TUNER
CD
Moving Control
Downloaded From Disc-Player.com
Samsung
Manuals
Rev Mode
Deck 1/2
TAPE
Manual EQ /Enter
Mono/ST
Program
TAPE
Manual EQ /Enter
Deck 1/2
Program
CD Repeat
Shuffle
REC/Pause
High
wn
Do
3
CD
Moving Control
Preset/Manual
Up
CD Synchro
Loading and Changing Compact
Discs
Setting the Clock
GB
The CD disc changer can contain up to three 12 cm or 8 cm
compact discs without using an adapter.
Your system is equipped with a clock which allows you to
turn your system on and off automatically. You should set the
clock:
When you purchase the mini-compact system
After a power failure
After unplugging the unit
Never force the compact disc carrousel when opening and closing the compartment.
Never press down or place objects on the carrousel.
Remember to reset the time when the clock changes from
winter to summer time and vice versa.
For each step, you have a few seconds to set the required
options. If you exceed this time, you must start again.
1
2
Switch the system on by pressing On/Standby.
3
Press Manual EQ/Enter.
Result: The hour flashes.
4
5
6
7
Always treat your compact discs with care; refer, if necessary, to
the section entitled “Precautions When Using Compact Discs” on
page 25.
Press Timer/Clock twice.
Result: CLOCK is displayed.
To...
Turn the Moving Jog knob to the...
Increase the hours
Decrease the hours
Right
Left
When the correct hour is displayed, press Manual EQ/Enter.
Result: The minutes flash.
To...
Turn the Moving Jog knob to the...
Increase the minutes
Decrease the minutes
Right
Left
1
2
Switch the system on by pressing On/Standby.
3
Place one or two discs in the front slots of the carrousel, with the label
on the discs facing upwards.
Check that the compact disc has been correctly inserted in
the holder before closing the compartment.
4
If you wish to load a third compact disc, press the Disc Change button on the front panel (or Disc Skip on the remote control).
Result: The carrousel rotates by 120°.
5
Close the compartment by pressing the Open/Close button again.
If you wish to start playing a disc directly, you can also
proceed as follows.
To play...
Press...
Disc 1
CD (
) or Disc 1
Disc 2
Disc 2
Disc 3
Disc 3
Result: The compartment closes automatically and the disc selected
starts playing.
When the correct time is displayed, press Manual EQ/Enter.
Result: The clock starts and is displayed, even when the system is in
standby mode.
You can display the time, even when you are using another function,
by pressing Timer/Clock once.
On/Standby
6
To change or unload the compact disc changer, repeat Steps 2 to 5.
Keep the compartment closed whenever you are not using it,
to prevent dust from entering.
Volu
+
Game
Aux
Press the Open/Close button on the front panel.
Result: The compartment opens.
You can load or unload compact discs when the radio,
tape or auxiliary source function is selected.
Demo
1
PTY
RDS
Display
Disc Change
–
Timer/
Clock
Disc11
Disc
Disc22
Disc
Band
2
TUNER
4,6
Moving Control
Rev Mode
3,5,7
CD
Deck 1/2
Manual EQ /Enter
Mono/ST
Program
On/Standby
Volume
+
Game
Counter Reset
Preset/Memory
CD Repeat
Aux
Dubbing
REC/Pause
High
wn
Do
Normal
CD REC/Pause
Preset/Manual
Shuffle
Up
CD Synchro
1
Demo
PTY
RDS
Display
5
Timer/
Clock
–
Band
ower
Surround
TUNER
CD
Moving Control
Downloaded From Disc-Player.com Samsung Manuals
2,5
4
5
TAPE
Open/
Open/
Close
Close
Disc33
Disc
TAPE
Manual EQ /Enter
Listening to a Compact Disc
Selecting a Disc in the CD changer
GB
When you have loaded at least one compact disc into the
player, you can start listening to it.
The CD function is automatically selected when DISC SKIP is
pushed.
Always treat your compact discs with care; refer, if necessary, to
the section entitled “Precautions When Using Compact Discs” on
page 25.
1
2
3
4
Switch the system on by pressing On/Standby.
Select the CD function by pressing CD (
If you wish to play the current disc only, press Repeat on the
remote control one or more times, until 1 CD is displayed.
) on the front panel.
Load one or more discs.
Press CD (
) on the front panel or
To select a specific disc, press the corresponding Disc (1, 2, 3) button on
the front panel or Disc Skip on the remote control, until the required disc
indicator flashes.
Result: All the discs will be played in turn, starting with the one selected.
on the remote control.
If you use the Disc (1, 2, 3) function when listening to the
radio or to a tape, the system switches automatically to the CD
mode.
If the disc selected is not loaded, the next disc is played automatically.
If you have loaded more than one compact disc, they will
be played in turn.
5
Adjust the volume as required by:
Turning the Volume knob on the front panel
or
Pressing the VOL. + or – buttons on the remote control
6
To pause temporarily during playback, press CD (
Disc Change
Disc 11
Disc
Disc 22
Disc
Disc 33
Disc
).
Volume
+
Game
Press CD (
) again to continue disc playback.
Demo
7
Press
when you have finished.
PTY
RDS
Display
When playing a disc, you can load new discs without
stopping the current one. To do so, open the compartment by
pressing Disc Change and load new discs in the other two
vacant slots (not the one containing the disc that you are playing). You cannot rotate the carrousel during playback.
When no discs are loaded, the “NO DISC” indication is displayed.
The CD player stops automatically after playing the three
discs, if the CD REPEAT function has not been selected.
Selecting a Track
You can select the track you wish to listen to, either when the
compact disc player is stopped or when a disc is playing.
Disc Change
Disc 1
Disc 2
Open/
Close
Disc 3
To start playback at the beginning of the... Turn the Moving Jog knob...
On/Standby
Volume
++
Game
Aux
Next track
Current track
Previous track
Track of your choice
One notch to the right
One notch to the left
Two notches to the left
The appropriate number of
notches to the right or to the left
Demo
1
PTY
RDS
Display
Timer/
Clock
––
2,4,6
Band
CD
CD
TUNER
Moving Control
Rev Mode
TAPE
5
ower
Surround
You can also use the
and
buttons on the front panel, or
the
and
buttons on the remote control.
Manual EQ /Enter
Deck 1/2
Mono/ST
–
Timer/
Clock
Program
Band
Counter Reset
Preset/Memory
CD Repeat
S.BASS
Dubbing
High
wn
Do
Normal
CD REC/Pause
REC/Pause
Preset/Manual
Preset/Manual
Shuffle
Up
CD Synchro
EQ
TUNER
CD
Moving Control
7
Rev Mode
Manual EQ /Enter
Deck 1/2
Mono/ST
Program
Counter Reset
Preset/Memory
CD Repeat
Dubbing
REC/Pause
High
wn
Do
Normal
CD REC/Pause
Downloaded From Disc-Player.com Samsung Manuals
TAPE
3D Surround
Pr
Preset/Manual
ual
Shuffle
Up
CD Synchro
Repeating One or All Tracks on the
Compact Discs
Searching for a Specific Music
Passage on a CD
GB
When listening to a compact disc, you can quickly search for a
specific music passage on a track.
It is recommended that you turn the volume down before using
this function.
To search through the tracks...
Press and hold down...
Forwards
Backwards
You can repeat indefinitely:
A specific track on a compact disc.
All tracks on the compact disc selected.
All discs loaded in the carrousel
1
for at least one second
for at least one second
Deck 1/2
Repeat
Mono/ST.
Tuner
2
CD
Band
TAPE
To repeat...
Press CD Repeat on the REMOTE
CONTROL one or more times
until...
The current track indefinitely
The selected disc
All discs loaded
REPEAT 1 is displayed
REPEAT 1 CD is displayed
REPEAT ALL CD is displayed
When you wish to stop the Repeat function, press Repeat until ALL
CD is displayed, or press
.
CD
VOL.
Power
Timer
Mute
On/Off
Tuning
Mode
CD
CD
VOL.
Sound
Mode
Disc Skip
Program
/Set
Aux
Deck 1/2
Repeat
Mono/ST.
Tuner
CD
Band
Programming the Order of Playback
Shuffle Function
The Shuffle function allows you to select and listen to the
tracks at random.
1
Press the Shuffle button on the front panel.
If this button is pressed while a CD is played back or stopped, any
tracks in the CD can be selected and played back without repeat.
2
To cancel, press
You can decide:
The order in which you listen to the tracks on the discs loaded
Which tracks you do not wish to listen to
You can programme up to 24 tracks.
You must stop the compact disc player before selecting the
tracks.
This feature can be combined with the Repeat function.
or the Shuffle button.
The CD player stops and the shuffle function is automatically
canceled when the music stops.
PTY
1
2
3
RDS
If the CD function is selected, stop the player by pressing
.
Load the selected CDs.
Press Program on the front panel.
Result: The following indications are displayed:
Display
–
Timer/
Clock
Band
ower
Surround
TUNER
CD
Moving Control
Rev Mode
Manual EQ /Enter
Deck 1/2
Mono/ST
Program
Counter Reset
Preset/Memory
CD Repeat
Dubbing
REC/Pause
High
wn
Do
Normal
CD REC/Pause
(01 = Programme n°, DI = Disc n°, – – = Track n° on the disc)
TAPE
Preset/Manual
Preset/Manual
1,2
2
Shuffle
Up
CD Synchro
S.BASS
EQ
4
If necessary, select the disc containing the required track by pressing
the corresponding Disc (1, 2, 3) button.
5
Select the required track by turning the Moving Jog knob:
To the left to move back through the tracks
To the right to move forward through the tracks
6
Press Program to confirm your selection.
3D Surround
Result: The selection is stored and
Downloaded From Disc-Player.com Samsung Manuals
is displayed.
Programming the Order of
Playback(Continued)
Checking or Changing Programmed
Tracks
GB
You can check or change your selection of tracks at any time.
7
8
9
To select other tracks, repeat Steps 4 to 6.
Press
1
2
to listen to the track selection in the order programmed.
To...
Turn the Moving Jog knob...
Listen to the current track again
Listen to the previous track
Listen to the next track
Skip forwards or backwards one
or more tracks
One notch to the left
Two notches to the left
One notch to the right
The appropriate number of
notches to the right or to the left
twice .
Once if the compact disc player is stopped
Result: PRGM is no longer displayed.
If you open the compartment, the selection is cancelled.
If you select the number of a disc which is not loaded or a track which does
not exist on the CD, the selection skips to the next programmed track.
Disc Change
Disc22
Disc
once if you have started listening to the selection.
Press Program/Set on the remote control.
Result: The following indications appear:
(C H= Check, 01=Program n˚, D1 = Disc n˚, – – = Track n° on the disc)
If you have already programmed 24 tracks, CH is displayed
instead of PR when you press Program/Set.
3
Press Program/Set again.
Result: The first track selected is displayed, together with the letter
CH (Change).
4
Press Program/Set one or more times until the track to be changed
is displayed.
5
If necessary, press the corresponding Disc (1, 2, 3) button to change
discs.
6
7
8
Press Tuning Down and Up to select a different track.
10 To cancel the selection, press
Disc11
Disc
Press
Disc33
Disc
4
Press Program/Set to confirm your change.
Press CD ( ) to start listening to the selection.
Result: The first track selected is played.
Sound
Mode
Volume
+
Game
Program
/Set
Disc Skip
Aux
2,3,4,7
Repeat Mono/ST.
Demo
Deck 1/2
PTY
Tuner
CD
RDS
Display
Band
Timer/
Clock
8
Band
TAPE
–
S
CD
CD
TUNER
TAPE
5,9
Moving Control
Rev Mode
Deck 1/2
Mono/ST
Program
Counter Reset
Preset/Memory
CD Repeat
Dubbing
REC/Pause
High
wn
Do
Normal
CD REC/Pause
1
3,6
8
CD
Manual EQ /Enter
Preset/Manual
Preset/Manual
Shuffle
Up
VOL.
CD Synchro
6
3D
1,10
6
Tuning
Mode
CD
CD
VOL.
Disc Change
Disc 1
Disc 2
Disc 3
5
by
Volume
+
Game
Demo
PTY
RDS
Display
Timer/
Clock
–
8
Band
CD
TUNER
Moving Control
Rev Mode
Deck 1/2
Counter Reset
Mono/ST
6
Dubbing
Downloaded From Disc-Player.com Samsung Manuals
Preset/Memory
1
Program
6
REC/Pause
High
wn
Do
Normal
CD REC/Pause
TAPE
Manual EQ /Enter
Preset/Manual
CD Repeat
Shuffle
Up
CD Synchro
Searching for and Storing the Radio
Stations
Searching for and Storing the Radio
Stations (continued)
GB
You can store up to:
Deck 1/2
Repeat
Mono/ST.
Tuner
CD
15 FM stations
8 AM(MW) stations
7 LW stations
7
TAPE
Band
3
CD
1
2
3
6
Switch the system on by pressing On/Standby.
VOL.
Select the TUNER function by pressing TUNER on the front panel.
Select the required frequency band by pressing TUNER (Band)
again on the front panel or TUNER (BAND) on the remote control.
Result: The appropriate indication is displayed:
FM
Frequency Modulation
AM(MW)
Medium Wave
LW
Long Wave
4
5
To search for a
station...
Press Preset/Manual on the front panel
or Tuning Mode on the remote control
Manually
Automatically
One or more times until MANUAL is displayed.
One or more times until AUTO is displayed.
Select the station to be stored by:
Turning the Moving Jog knob to the right or to the lef to increase
or decrease the frequency respectively
or
Pressing TUNING
or
on the remote control
To scroll through the frequencies faster when searching manually, hold down the Preset/Manual Down or Up buttons.
The automatic search procedure may stop on a frequency that
does not correspond to a radio station. If this happens, use the
manual search mode.
6
Adjust the volume by:
Turning the Volume knob on the front panel
or
Pressing the VOL. + or – buttons on the remote control
7
8
Tuning
Tuning
Mode
CD
4
5
CD
VOL.
5
6
Selecting a Stored Station
You can listen to a stored radio station as follows:
1
2
3
4
5
Switch the system on by pressing On/Standby.
Select the TUNER function by pressing TUNER on remote control.
Select the required frequency band by pressing Tuner (Band) on the
remote control or TUNER (Band) again on the front panel.
Press the Preset/Manual button on the front panel of the unit, or the
Tuning Mode button on the remote control until “PRESET” is displayed.
Tuning the multi-jog on the front panel left or right until the desired
station is found.
or
Select the desired station by pressing the station number stored,
using the Tuning
or
button on the remote control.
Result: The desired station is now received.
Select the stereo or mono mode by pressing Mono/ST.
If you do not want to store the radio station found, revert to Step 4
and search for another station.
Otherwise:
a Press Preset Memory on the front panel.
Result: The programme number and PRGM are displayed for a
few seconds.
b Press Preset/Manual Down and Up to assign a programme
number between 1 and 15.
c Press Preset Memory to store the radio station.
Result: PRGM is no longer displayed and the station is stored.
9
To store any other radio frequencies required, repeat Steps 3 to 8.
The PROGRAM function can be used to assign a new station to
an existing programme number.
On/Standby
Aux
Timer
On/Off
Mute
Sound
Mode
Disc Skip
Program
/Set
4
Aux
CD
Deck 1/2
Repeat
Mono/ST.
5
VOL.
5
2,3
Tuner
Tuning
Tuning
Mode
CD
VOL.
CD
Band
Improving Radio Reception
You can improve the quality of radio reception by:
Rotating the FM or AM(MW) aerial
Testing the positions of the FM and AM(MW) aerials before fixing
them permanently
Volume
+
Game
1
1 Power
If reception from a specific FM radio station is poor, press Mono/ST.
to switch from stereo mode to mono. The quality of the sound will be
improved.
Demo
PTY
RDS
Display
2,3
Timer/
Clock
Band
–
TUNER
Moving Control
CD
Preset/Memory
Dolby
NR Counter Reset
6
ower
Surround
Mono/ST
Program
Preset Memory
CD Repeat
S.BASS
REC/Pause
Dubbing
wn
Do
Preset/Manual
Preset/Manual
Normal
High
CD REC/Pause
Rec/Pause
Up
Sound
Mode
Disc Skip
Program
/Set
Aux
Deck 1/2
Repeat
Mono/ST.
Tuner
7
5
Manual EQ /Enter
Mono/STDeck 1/2
Rev Mode
TAPE
8
5,8 Manuals
5,8 4 Samsung
Downloaded From Disc-Player.com
Shuffle
CD Synchro
CD
EQ
Band
3D Surround
TAPE
Listening to a Cassette
CD Synchro Record Feature
GB
Always treat your cassettes with care; refer, if necessary, to
the section entitled “Precautions When Using Audio Cassettes”
on page 25.
1
2
3
Synchronized recording
Direct recording
This feature enables you to synchronize the start of the recording with the start of the disc or track of your choice.
Switch the system on by pressing On/Standby.
Select the TAPE function by pressing TAPE on the front panel.
1
2
3
4
5
6
Open either cassette deck 1 or 2 by pushing and releasing the deck
cover where Push Eject ( ) is written.
4
Insert the pre-recorded cassette with the open edge of the tape facing downwards.
5
Close the deck by pushing on it until it clicks into place.
Result: Depending on the deck selected, the 1 or 2 indication is
displayed in front of the counter number.
Switch the system on by pressing On/Standby.
Insert a blank cassette in Deck 2.
Select the CD function by pressing CD on the front panel.
Load a compact disc.
Select the required disc.
Select the required track and press CD Synchro or press CD
Synchro directly to start recording at the beginning of the disc.
Result: REC is displayed and recording starts.
If you insert a cassette in both decks, the system selects the
deck in which you inserted the second cassette.
6
You can record a compact disc on a cassette in two different ways:
7
If you have inserted two cassettes, press Deck 1/2 on the front
panel or directly the Deck 1/2 button on the remote control to select
the cassette to be played.
To stop...
Recording and playing the compact disc
–
Timer/
Clock
Band
Result: Depending on the deck selected, the TAPE 1 or TAPE 2 indication is displayed.
7
)
)
High
6
REC/Pause
Shuffle
S.BASS
EQ
CD Synchro
Up
Preset/Manual
3D Surround
You do not need to adjust the volume, as it has no effect on
the recording.
PTY
RDS
Display
Timer/
Clock
2,7
Band
TUNER
TAPE
TAPE
CD
Moving Control
Mono/ST
Program
Counter Reset
Preset/Memory
CD Repeat
6
Dubbing
REC/Pause
wn
Do
8
1
2
3
4
5
6
Switch your system on by pressing On/Standby.
7
Press the CD Rec/Pause.
Result: REC flashes.
8
Press the
to start playing the track.
Result: The track is recorded on the cassette.
9
When you have finished recording, press
for Deck 2 on the
remote control or
on the front panel to stop recording.
Insert a blank cassette in Deck 2.
Select the CD function by pressing CD on the front panel.
Load the compact disc.
Select the required disc.
Select the required track on the compact disc and press
on the front panel or
on the remote control to set the compact disc player to Pause mode.
Manual EQ /Enter
Deck 1/2
High
7
You can only record on cassettes in Deck 2.
Demo
Normal
CD REC/Pause
CD Repeat
The direct recording mode enables you to start recording with
any track on the compact disc.
V
Rev Mode
Preset/Memory
Recording a Compact Disc
Press ...
Game
1
Program
Counter Reset
Normal
CD REC/Pause
On/Standby
Aux
Manual EQ /Enter
Mono/ST
Dubbing
When the cassette is stopped, select one of the following functions
as required.
To...
Rewind the cassette
Fast-forward the cassette
3
Moving Control
In case of MAX-N72/N73, this function is possible only in
Deck 2.
8
TAPE
Deck 1/2
wn
Do
Press ...
TAPE (
TAPE (
ower
Surround
CD
TUNER
Rev Mode
To listen to...
Side A
Side B
Result: The cassette starts playing.
Press ...
Pre
ual
Preset/Manual
Shuffle
Up
CD Synchro
8
On/Standby
Volume
+
Game
Demo
Aux
1
PTY
RDS
Display
3,6,8
Timer/
Clock
Band
–
ower
Surround
CD
CD
TUNER
Moving Control
Rev Mode
Downloaded From Disc-Player.com Samsung Manuals
7
TAPE
Manual EQ /Enter
Deck 1/2
Mono/ST
Counter Reset
Preset/Memory
Dubbing
CD Repeat
S.BASS
REC/Pause
High
wn
Do
Normal
CD REC/Pause
Program
9
Preset/Manual
Preset/Manual
Shuffle
Up
CD Synchro
EQ
3D Surround
Recording a Radio Programme
Copying a Cassette (Dubbing)
GB
You can record a radio programme of your choice.
You can only record on cassettes in Deck 2.
You do not need to adjust the volume, as it has no effect on the
recording.
1
2
3
4
You can copy a cassette from Deck 1 to Deck 2. Two options are available:
Normal speed dubbing
High-speed dubbing
You do not need to adjust the volume, as it has no effect on the recording.
Take care not to insert the tape to be copied in Deck 2, as it will
be erased when you start recording.
Switch the system on by pressing On/Standby.
Insert a blank cassette in Deck 2.
Select the TUNER function by pressing TUNER on the front panel.
Select the radio station that you wish to record by pressing TUNING
or
on the remote control or by press the Preset/Manual
Down or Up on the front panel.
5
Press Rec/Pause (
).
Result: REC is displayed in red and recording starts.
6
When you have finished recording, press the
for Deck 2 on the
remote control or
on the front panel to stop recording.
Volume
Insert a blank cassette in Deck 2.
Insert the tape to be copied in Deck 1.
To copy a cassette at...
Press...
Normal speed
DUBBING NORMAL
High speed
DUBBING HIGH
5
Press
on the front panel or
for each deck on the remote
control when you have finished recording.
On/Standby
+
Game
1
PTY
RDS
Volume
+
Game
Aux
Demo
1
Switch your system on by pressing On/Standby.
Result: The appropriate indications are displayed and the cassette in
Deck 1 is copied to the cassette in Deck 2.
On/Standby
Aux
1
2
3
4
Demo
PTY
RDS
Display
Display
–
Timer/
Clock
–
3
Timer/
Clock
Band
Band
ower
Surround
TUNER
TUNER
CD
TAPE
Deck 1/2
Mono/ST
Counter Reset
Preset Memory
Manual EQ /Enter
Mono/ST
Program
Manual EQ /Enter
Mono/STDeck 1/2
Rev Mode
Mono/ST
Preset/Memory
Dolby
NR Counter Reset
Preset Memory
REC/Pause
Dubbing
wn
Do
Preset/Manual
Preset/Manual
Normal
High
CD REC/Pause
Rec/Pause
Up
Program
5
4
Dubbing
CD Repeat
Normal
CD REC/Pause
Shuffle
Preset/Memory
CD Repeat
5
High
S.BASS
EQ
REC/Pause
Shuffle
CD Synchro
Rec/Pause
wn
Do
6
4
TAPE
Moving Control
Rev Mode
Moving Control
CD
Preset/Manual
Preset/Manual
Up
3D Surround
CD Synchro
4
Selecting the Cassette Playback Mode
Your mini-compact system has three cassette playback modes
which enable you to listen to both sides of a cassette automatically.
Press Rev Mode until the appropriate symbol is displayed.
When the display indicates...
The mini-compact system plays back...
one side of the selected cassette and then
stops.
One side of the cassette.
The other side of the cassette and then stops.
Both sides of the cassette indefinitely until
you press stop.
In case of MAX-N72/N73, this function is possible only in Deck 2.
Moving Control
Mono/ST
Mono/ST
Program
Counter Reset
Preset Memory
Preset/Memory
CD Repeat
Dubbing
REC/Pause
Shuffle
CD Synchro
Rec/Pause
High
wn
Do
Normal
CD REC/Pause
Downloaded From Disc-Player.com Samsung Manuals
Manual EQ /Enter
Deck 1/2
Rev Mode
Preset/Manual
Up
Tape Counter
Counter display (Only MAX-N73/N72)
GB
When playing a cassette in one of the cassette decks, a counter
is displayed to enable you to take note of the counter value at
the start of each track to start playback at the beginning of the
track to which you wish to listen.
Before starting to record a cassette for which you wish to take
note of the counter values at the beginning of each track, reset the
counter by pressing Counter Reset on the front panel.
It’s a function to be used when confirming the numerical
value about an action progress status at the time of tape
reproducing or recording.
Press Counter Display on the front panel.
PTY
RDS
Display
Each cassette deck has a separate counter.
–
Timer/
Clock
Band
Band
TUNER
CD
TAPE
Moving Control
TUNER
Deck 1/2
Mono/ST
Mono/ST
Program
Counter Reset
Preset Memory
Preset/Memory
CD Repeat
Rev Mode
Dubbing
Rev Mode
Preset/Manual
Deck 1/2
Counter Display Counter Reset
Dubbing
Up
Normal
CD REC/Pause
Mono/ST
Program
Preset Memory
Preset/Memory
CD Repeat
REC/Pause
Shuffle
CD Synchro
Rec/Pause
High
(Only MAX-N73/N72)
Dolby Noise Reduction System
(Only MAX-N75)
Your mini-compact system has a Dolby Noise Reduction
feature, produced under license, in order to remove background noise (noise or hiss) when listening to a cassette.
1
To activate the DOLBY NR mechanism, press Dolby NR on the front
panel.
2
To deactivate the DOLBY NR mechanism, press Dolby NR again
For good quality sound, it is recommended to use DOLBY NR
function for cassettes recorded in DOLBY NR.
™ Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation.
DOLBY and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
–
Timer/
Clock
Band
TUNER
CD
TAPE
Moving Control
Manual EQ /Enter
Mono/ST
Mono/ST
Program
Dolby NR Counter Reset
Preset Memory
Preset/Memory
CD Repeat
Dubbing
Rec/Pause
Rev Mode
REC/Pause
Shuffle
CD Synchro
wn
Do
Normal
CD REC/Pause
Deck 1/2
High
(Only MAX-N75)
Downloaded From Disc-Player.com Samsung Manuals
Preset/Manual
Up
Manual EQ /Enter
Mono/ST
wn
Do
High
TAPE
Moving Control
REC/Pause
Shuffle
CD Synchro
Rec/Pause
wn
Do
Normal
CD REC/Pause
CD
Manual EQ /Enter
Preset/Manual
Up
Timer Function
GB
The timer enables you to switch the system on or off at specific times.
Example: You wish to wake up to music every morning.
9
Press On/Standby to set the system to standby mode.
Result:
is displayed to the upper right of the time, indicating that
the timer has been set. The system will switch on and off
automatically at the required times.
If you no longer want the system to be switched on or off
automatically, you must cancel the timer.
Before setting the timer, check that the current time is correct.
For each step, you have a few seconds to set the required
options. If you exceed this time, you must start again.
1
2
3
4
Switch the system on by pressing On/Standby.
TIMER is displayed.
Press Timer/Clock until
Press Manual EQ/Enter on the front panel.
Result: ON TIME is displayed (instead of the equalizer symbols) for
a few seconds, followed by any switch-on time already set;
you can set the timer switch-on time.
If the timer switch on and off times are identical, the word
ERROR is displayed.
On/Standby
V
Game
Aux
1,9
Demo
PTY
RDS
Display
Timer/
Clock
Band
2
Set the timer switch-on time.
TUNER
Moving Control
a
b
6
7
Press Manual EQ/Enter.
Result: The minutes flash.
c
Set the minutes by turning the Moving Jog knob to the right or to
the left.
d
Press Manual EQ/Enter.
Result: OFF TIME is displayed (instead of the equalizer symbols)
for a few seconds, followed by any switch-off time already
set; you can now set the timer switch-off time.
Set the timer switch-off time.
a
Set the hour by turning the Moving Jog knob to the right or to
the left.
b
Press Manual EQ/Enter.
Result: The minutes flash.
c
Set the minutes by turning the Moving Jog knob to the right or to
the left.
d
Press Manual EQ/Enter.
Result: VOL XX is displayed, where XX corresponds to the volume already set.
Turn the Moving Jog knob to adjust the volume level and press
Manual EQ/Enter.
Result: The source to be selected is displayed.
Turn the Moving Jog knob to select the source to be played when
the system switches on.
If you select...
You must also...
TAPE (cassette)
Insert a recorded cassette in one of the
decks before setting the system to standby.
a Press Manual EQ/Enter.
b Select the FM or AM frequency band
by turning the Moving Jog knob to
the right or to the left.
c Press Manual EQ/Enter.
d Select a preset station by turning the
Moving Jog knob to the right or to
the left.
TUNER (radio)
CD (compact disc)
8
a Load one or more compact discs.
b Select the required disc.
Press Manual EQ/Enter
confirm the timer.
Downloaded From Disc-Player.com
Samsung to
Manuals
Rev Mode
TAPE
Manual EQ /Enter
Deck 1/2
Mono/ST
Program
Counter Reset
Preset/Memory
CD Repeat
Dubbing
Normal
CD REC/Pause
REC/Pause
High
wn
Do
5
Set the hour by turning the Moving Jog knob to the right or to
the left.
3,4,5,6,7,8
CD
4,5,6,7
Preset/Manual
Shuffle
Up
CD Synchro
Cancelling the Timer
Power Sound/Surround Function
GB
After having set the timer, it will start automatically as shown
by the TIMER indication on the display. If you no longer wish to
use the timer, you must cancel it.
You can stop the timer at any time (system on or in standby mode).
To...
Press Timer-On/Off...
Cancel the timer
Once.
Result:
is no longer displayed.
Restart the timer
Twice.
Result:
is displayed again.
Power
Timer
On/Off
Your mini-compact system is equipped with the function of
Power Sound and Power Surround.
The function of Power Sound amplifies bass and improves
high key or bass twice as much for you to appreciate powerful real sound.
The Power Surround replaces conventional stereo sound with
a wider and more true-to -life sound. It creates the feeling of
being right at the centre of the music and being surrounded
by total music sound.
Press Power Surround button on the front panel until the
required option is selected. Each time the Power Surround button is pressed, “POWER SOUND, POWER SURROUND, OFF”
are selected in this order.
Mute
PTY
Sound
Mode
Disc Skip
Program
/Set
Aux
Deck 1/2
Repeat
Mono/ST.
Tuner
RDS
Display
–
Timer/
Clock
Band
CD
ower
ower
Surround
Surround
TUNER
CD
Band
TAPE
Moving Control
Rev Mode
TAPE
Manual EQ /Enter
Deck 1/2
Mono/ST
Program
Counter Reset
Preset/Memory
CD Repeat
CD
S.BASS
Dubbing
Mute Function
Preset/Manual
EQ
CD Synchro
Up
3D Surround
Super Bass System (SBS)
You can turn the sound off temporarily on your system.
Example: You wish to answer a telephone call.
1
2
High
wn
Do
Normal
CD REC/Pause
Shuffle
REC/Pause
Press MUTE on the remote control.
To switch the sound back on (at the same volume as before), press
MUTE again or the VOLUME buttons.
Your mini-compact system has a bass amplification function called SBS (Super Bass System). This function makes
the sound more powerful and real.
1
Press the S. BASS button on the front panel.
Result: SBS ON is displayed for a few seconds.
2
To cancel this function, press S. BASS again.
Result: SBS OFF is displayed for a few seconds.
RDS
Display
Power
Timer
On/Off
Mute
–
Timer/
Clock
Band
ower
Surround
TUNER
Sound
Mode
Disc Skip
Program
/Set
Aux
Deck 1/2
Repeat
Mono/ST.
Tuner
CD
Moving Control
Rev Mode
TAPE
Manual EQ /Enter
Deck 1/2
Mono/ST
Counter Reset
Preset/Memory
Program
CD Repeat
S.BASS
S.BASS
Normal
CD REC/Pause
Band
TAPE
CD
Downloaded From Disc-Player.com Samsung Manuals
Shuffle
REC/Pause
High
wn
Do
CD
Dubbing
Preset/Manual
Up
CD Synchro
EQ
EQ
3D Surround
User EQ Setting
3D Surround Function
GB
User EQ Setting Function allows you to control tones of
music.
1
2
This model provides 3D Surround modes so that you can
enjoy virtually original sound.
Press Manual EQ/Enter button on the front panel.
Result: USER EQ is displayed, and the part to be controlled flashes.
Using the Moving Jog knob, select a tone that you want. Then,
press the Manual EQ/Enter button.
Result: Pre-set part stops flashing, and the part to be controlled
next starts to flash.
Press 3D Surround on the front panel until the required option
is selected. Each time the 3D Surround button is pressed,
“HALL(Concert hall mood), LIVE(Live house sound), MOVIE
(Cinema mood), OFF” are selected in this order.
PTY
RDS
3
Display
Repeat the procedures of above 1 and 2 to control tones of music.
When USER 1 is displayed, select a USER EQ number using the
Moving Jog knob. Then, press the Manual EQ/Enter button.
Result: USER X flashes a few seconds, and all procedures are completed. ( X = USER EQ number)
–
Timer/
Clock
Band
CD
Moving Control
Rev Mode
Repeat above procedures 1 to 3 to setup up to three USER EQs.
ower
Surround
TUNER
Mono/ST
Program
Counter Reset
Preset/Memory
CD Repeat
S.BASS
REC/Pause
High
wn
Do
Normal
CD REC/Pause
–
Manual EQ /Enter
Deck 1/2
Dubbing
Timer/
Clock
TAPE
Preset/Manual
Shuffle
Up
CD Synchro
EQ
EQ
3D Surround
Surround
3D
Band
TUNER
Rev Mode
2,3
CD
Moving Control
Deck 1/2
Mono/ST
Counter Reset
Preset/Memory
Dubbing
Program
CD Repeat
Shuffle
REC/Pause
wn
Do
Normal
CD REC/Pause
High
TAPE
Manual EQ /Enter
1,3
Preset/Manual
Press SOUND MODE on the remote control until the required
option is selected. Each time the SOUND MODE button is
pressed in sequence, the equalizer modes, 3D Surround
modes and Power Surround modes “PASS, POP, ROCK, CLASSIC, USER 1, USER 2, USER 3, HALL, LIVE, MOVIE, POWER
SOUND, POWER SURROUND” are selected in this order.
CD Synchro
Up
Selecting an Equalizer Preset
Your mini-compact system is equipped with a preset equalizer
that allows you to choose the most appropriate balance
between treble and bass frequencies, according to the type
of music you are listening to.
Press EQ on the front panel until the required option is selected.
Equalizer mode
PASS
POP
ROCK
CLASSIC
USER 1, 2, 3
Normal balance (linear)
Balance suitable for pop music
Balance suitable for rock music
Balance suitable for classic music
–
Timer/
Clock
Band
ower
Surround
TUNER
CD
Moving Control
Rev Mode
TAPE
Manual EQ /Enter
Deck 1/2
Mono/ST
Counter Reset
Preset/Memory
Program
CD Repeat
S.BASS
REC/Pause
Dubbing
High
wn
Do
Normal
CD REC/Pause
Preset/Manual
Shuffle
Up
Downloaded From Disc-Player.com Samsung Manuals
CD Synchro
EQ
EQ
3D Surround
Game Function
Connecting Headphones
GB
You can enjoy simple games on the display window of the front
panel.
1
Press Game on the front panel.
Result: SHOOTING flashes.
2
Turn the Moving Jog knob to the right or to the left.
Result: RACING and SHOOTING are displayed alternately.
3
4
You can connect a set of headphones to your mini-compact
system so that you can listen to music or radio programmes
without disturbing other people in the room. The earphones
must have a 6.3 mm jack or an appropriate adapter.
Connect the headphones to the Phones jack on the front panel.
Result: The loudspeakers are no longer used to output the sound.
Prolonged use of headphones at a high volume may damage
your hearing.
Press the Manual EQ/Enter button to select a game.
Result: 01 LEVEL is displayed. (01=level of a game)
Turn the Moving Jog knob to select a level. Then, press the Manual
EQ/Enter button.
Result: The game gets started.
On/Standby
Volu
+
Game
Aux
Demo
PTY
RDS
SHOOTING :
Move the Moving Jog knob to attack the enemies and press the
Manual EQ/Enter button to shoot.
RACING:
Move the Moving Jog knob to avoid crashing with the enemies
coming down.
Display
–
Timer/
Clock
Band
TUNER
Rev Mode
On/Standby
Vol
+
Game
Aux
1
Demo
PTY
RDS
Display
–
Timer/
Clock
Band
TUNER
Rev Mode
3,4
CD
Moving Control
Deck 1/2
Mono/ST
Counter Reset
Preset/Memory
Dubbing
Program
CD Repeat
REC/Pause
High
wn
Do
Normal
CD REC/Pause
Downloaded From Disc-Player.com Samsung Manuals
TAPE
Manual EQ /Enter
Preset/Manual
Shuffle
2,4
Up
CD Synchro
TAPE
Manual EQ /Enter
Deck 1/2
Mono/ST
Program
Counter Reset
Preset/Memory
CD Repeat
Dubbing
Normal
CD REC/Pause
REC/Pause
High
wn
Do
You starts with three lives.
When the unit bumps against the enemy, you will lose one
live. Then, “CRASH” appears on the display window.
You will be leveled up after you reaching the settled point.
When you play “SHOOTING” game, everytime the enemy
arrives at the settled line, the remaining energy diminish one
by one.
After finishing the game, “GAME OVER” appears on the display window. If you want to restart the game, repeat the
process 1 to 4.
CD
Moving Control
Preset/Manual
Shuffle
Up
CD Synchro
Connecting to an External Source
Safety Precautions
GB
The auxiliary input can be used to take advantage of the sound quality
of your mini-compact system when listening to other sources.
Examples: A television
A video disc player
A DAT or DCC cassette player
A Hi-Fi stereo video cassette recorder
The following diagrams illustrate the precautions to be taken
when using or moving your mini-compact system.
To connect the external source, the source must have an audio
output. In addition, you need an RCA connection cable.
Disc Change
Disc 1
Disc 2
Open/
Close
Disc 3
Disc Change
Disc 1
Disc 2
Open/
Close
Disc 3
On/Standby
Volume
+
Game
On/Standby
Demo
Aux
Volume
+
Game
PTY
RDS
Aux
Demo
Display
–
Timer/
Clock
PTY
RDS
Band
ower
Surround
Display
Band
Connect the audio cable to the rear of the mini--compact system.
Connect the...
Red jack
White jack
Manual EQ /Enter
Mono/ST
Preset/Memory
Program
CD Repeat
S.BASS
Program
CD Repeat
Dubbing
Normal
CD REC/Pause
S.BASS
Dubbing
Normal
CD REC/Pause
To the connector marked...
R (right)
L (left)
REC/Pause
High
Shuffle
4
Select the AUX source by pressing AUX on the front panel or on the
remote control.
Result: AUX is displayed.
Shuffle
EQ
CD Synchro
Up
Preset/Manual
3D Surround
3D Surround
For optimum sound quality, do not invert the right and left channels.
Plug the system back into the main socket and press On/Standby to
switch it on.
REC/Pause
High
EQ
CD Synchro
Up
Preset/Manual
Ambient operating conditions:
Ambient temperature
5°C-35°C
Humidity
10-75%
3
Do not expose the unit to direct sun
radiation or other heat sources.
This could lead to overheating and
malfunction of the unit.
Disc Change
Disc 1
Disc 2
Open/
Close
Disc 3
Disc Change
Disc 1
Disc 2
Open/
Close
Disc 3
On/Standby
Volume
+
Game
On/Standby
Volume
+
Game
Demo
Aux
Aux
PTY
Demo
RDS
Display
PTY
Switch the external source on.
RDS
–
Timer/
Clock
Display
Band
ower
Surround
–
Timer/
Clock
Band
TUNER
ower
Surround
TUNER
CD
CD
Moving Control
TAPE
Rev Mode
Moving Control
Rev Mode
TAPE
Manual EQ /Enter
Deck 1/2
Mono/ST
Counter Reset
Preset/Memory
Program
Manual EQ /Enter
Deck 1/2
Mono/ST
Program
Counter Reset
Preset/Memory
CD Repeat
CD Repeat
S.BASS
Dubbing
n
Dow
Adjust the volume and balance as required:
Volume
Equalizer
Example: You can watch a film and take advantage of stereo sound
provided that the original sound track is in stereo, (as if you
were in a cinema).
On/Standby
Shuffle
REC/Pause
High
Preset/Manual
Up
CD Synchro
Normal
CD REC/Pause
EQ
Shuffle
REC/Pause
S.BASS
Dubbing
Normal
CD REC/Pause
n
Dow
5
6
TAPE
Moving Control
Deck 1/2
Counter Reset
Rev Mode
TAPE
Manual EQ /Enter
Mono/ST
Preset/Memory
n
Dow
2
CD
Moving Control
Deck 1/2
Counter Reset
Rev Mode
n
Dow
1
CD
ower
Surround
TUNER
Set the system to standby mode and disconnect it and the external
source from the main.
TUNER
–
Timer/
Clock
High
Preset/Manual
Up
EQ
CD Synchro
3D Surround
3D Surround
Do not place potted plants or vases
on top of the unit. Moisture entering
the unit could lead to dangerous
electric shock and can cause
equipment damage. In such events
immediately disconnect the main
plug from the socket.
During thunderstorms, disconnect
the main plug from the socket.
Main voltage peaks due to lightning
could damage the unit.
Vo
VOLUME
Game
UP
Aux
Demo
PTY
DOWN
RDS
Display
Timer/
Clock
Band
CD Digital Out Jack
Remove the batteries from the
remote control, if not used for any
extended periods.
Leaking batteries can cause serious
damage to the remote control.
When using headphones, take care
not to listen at excessive volumes.
Extended use of headphones at
high volumes will lead to hearing
damage.
This unit can output CD digital sound signals through this
jack. Use an optical cable to connect digital audio equipment.
(DAT deck, MD recorder, etc.).
Remove the dust cap (1) from the CD DIGITAL OUT jack. Then,
connect an optical cable plug to the CD DIGITAL OUT jack.
Disc Change
Disc 1
Disc 2
Open/
Close
Disc 3
On/Standby
Volume
+
Game
Aux
Demo
PTY
RDS
Display
–
Timer/
Clock
Band
ower
Surround
TUNER
CD
Moving Control
Rev Mode
TAPE
Manual EQ /Enter
Deck 1/2
Mono/ST
Counter Reset
Preset/Memory
Program
CD Repeat
S.BASS
Dubbing
(1)
When the CD DIGITAL OUT jack is not being used
Attach
the supplied dust
cap. Manuals
Downloaded From
Disc-Player.com
Samsung
Do not place heavy items on the
main lead. Main cable damage can
lead to damage of the equipment (fire
hazard) and can cause electric
shock.
Shuffle
REC/Pause
High
n
Dow
Normal
CD REC/Pause
Preset/Manual
Up
CD Synchro
EQ
3D Surround
Do not remove any equipment panels.
The inside of the unit
contains live components, which
cause electric shock.
Cleaning Your Mini-Compact
System
Precautions When Using Audio
Cassettes
GB
Check that the tape in the cassette is sufficiently taught.
To prevent erasing a cassette that you wish to keep, remove the safety
tab on the upper edge of the cassette. To record a cassette, where the
tab has been broken, simply cover the opening with adhesive tape.
When you have finished playing a cassette, always put it back in its case.
Store your cassettes in a clean place, out of direct sunlight, where they
will not be exposed to high temperatures.
Avoid using 120-minute cassettes as they place unnecessary strain on
the tape mechanism.
To obtain the best possible results from your mini-compact system,
you must clean the following elements regularly:
The outer casing
The compact disc player
The cassette players (heads, rollers and drive capstans)
Always unplug the system from the wall outlet:
Before cleaning it
If you are not going to be using it for a long time
Outer Casing
Clean the outer casing regularly using a soft cloth and a light detergent. Do not use
abrasive powders, liquids or aerosol cleaners. Never let any liquids get into the system.
Compact Disc Player
Before playing a compact disc, clean it with a special CD cleaning
agent. Do not use the same cleaning agents as for vinyl LP records.
Carefully wipe the disc from the centre outwards.
Before Contacting the After-Sales
Service
1
2
Regularly clean the player with a special cleaning disc (available from
your local dealer).
Tape Decks
Press EJECT(
1
2
It always takes a little time to become familiar with a new appliance. If you have any of the problems listed below, try the solutions given. They may save you the time and inconvenience of an
unnecessary service call.
) to open the cassette deck.
Problem
Use a cotton bud and a special cassette cleaning agent to clean the:
Head (1)
Rollers (2)
Drive capstans (3)
If you will not be using the remote control for a long time,
remove the batteries to prevent corrosion.
Although your system is very hard-wearing, it should not be
used in an excessively dusty environment or subjected to
shocks or extreme heat (close to heating appliances or in
direct sunlight, etc.).
If the unit emits an unpleasant odour when in use, unplug it
from the main supply and contact the after-sales service.
G
E
N
E
R
A
L
3
The system does not work
• The main lead is not correctly plugged into a
wall socket or the wall socket is not switched on.
• The remote control batteries need replacing or
the polarity has not been respected.
• The On/Standby button has not been pressed.
There is no sound
• The volume has been completely turned down.
• The correct function (TUNER, CD, TAPE, AUX)
has not been selected.
• You have connected a set of earphones.
• The loudspeaker wires have been disconnected.
• The Mute button has been pressed.
The Timer does not work
• The timer has been stopped by pressing Timer
On/Off.
Incase it is not worked, even the
action is taken as above.
• Press the S. Bass button for 5 seconds in
power ‘OFF’(standby), then it is returned the
original position (RESET)
The compact disc player does not
start playing
• The CD function has not been selected.
• The disc has been inserted face down or is
either dirty or scratched.
• The laser sensor is dirty or dusty.
• The system has not been installed on a flat,
horizontal surface.
• Condensation has formed in the player; leave
the system in a warm, airy room for at least
one hour.
The tape does not start playing
• The TAPE function has not been selected.
• The cassette has not been inserted correctly.
• The cassette player has not been closed.
• The tape is either slack or broken.
The volume falls off
The cassette is not erased correctly
There is excessive wow and flutter
• The audio heads are dirty.
• The rollers or drive capstans are dirty.
• The tape is worn.
Reception is poor or no radio stations are received at all
• The TUNER function has not been selected.
• The radio frequency has not been correctly
selected.
• The aerial has been disconnected or is not facing the right way. Turn it until you find the best
orientation.
• You are in a building that blocks radio waves;
you must use an outside aerial.
C
D
1
2
Precautions When Using Compact
Discs
Handle your compact discs with care. Always hold them by the edges
to avoid leaving fingerprints on the shiny surface.
When you have finished playing a compact disc, always put it back in its case.
Do not fix paper or adhesive tape to the discs and do not write on the label.
Clean them with a special-purpose cloth.
Store your compact discs in a clean place, out of direct sunlight,
where they will not be exposed to high temperatures.
Always use compact discs marked.
COMPACT
DIGITAL AUDIO
Downloaded From Disc-Player.com Samsung Manuals
C
A
S
S
E
T
T
E
S
R
A
D
I
O
Checks/Explanation
If the above guidelines do not allow you to solve the problem, take a note of:
The model and serial numbers, normally printed on the rear of the system
Your warranty details
A clear description of the problem
Then contact your local dealer or SAMSUNG after-sales service.
Technical Specifications
GB
SAMSUNG strives to improve its products at all times. Both the design specifications and
these user instructions are thus subject to change without notice.
RADIO
LW
Usable sensitivity
AM (MW)
Signal/noise ratio
Usable sensitivity
Total harmonic distortion
FM
Signal/noise ratio
Usable sensitivity
Total harmonic distortion
60 dB
40 dB
54 dB
2%
62 dB
10 dB
0.3 %
COMPACT DISC PLAYER
Capacity
Frequency range
Signal/noise ratio
Distortion
Channel separation
Disc sizes
3 discs
20 Hz - 20 KHz (± 1 dB)
90 dB (at 1 KHz) with filter
0.05 % (at 1 KHz)
74 dB
Diameter: 120 or 80 mm. Thickness: 1.2 mm
TAPE DECK
Frequency range
Signal/noise ratio
Channel separation
Erasing effect
125 Hz ~ 8 KHz
40 dB
35 dB
60 dB
AMPLIFIER
Output power (6 Ω)
Channel separation
Signal/noise ratio
2 x 120 Watts RMS (total harmonic distortion: 10 %) ........MAX-N72/N73
2 x 200 Watts RMS (total harmonic distortion: 10 %) ........MAX-N75
50 dB
75 dB
GENERAL
Dimensions
270 (W) x 317 (H) x 340 (D) mm
Downloaded From Disc-Player.com Samsung Manuals
THIS APPLIANCE IS MANUFACTURED BY:
ELECTRONICS
Downloaded From Disc-Player.com Samsung Manuals
AH68-00357B