advertisement
SLF
5
INSTRUCTION MANUAL
We’ll Make It Stress-Free
If you have any questions along the way, just give us a call.
1-888-333-1376 (UK: 0800-056-2853). We’re ready to help!
Scan for easy install video http://san.us/306
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
1
Before getting started, let’s make sure this mount is perfect for you!
Does your TV weigh
more
than 56.7 kg (125 lb) including accessories?
(56.7 kg)
125 lb
No — Perfect!
Yes — This mount is NOT compatible. Visit Simplicity.Sanus.com or call 1-888-333-1376 (UK: 0800-056-2853) to fi nd a compatible mount.
2
What is your wall made of?
Drywall with wood studs
Perfect!
Solid concrete or concrete block
Perfect!
?
Unsure?
Call 1-888-333-1376 (UK: 0800-056-2853)
3
Do you have all of the tools needed?
2
4
5.5 mm
(7/32 in.)
10 mm
(3/8 in.)
13 mm
(1/2 in.)
Ready to begin?
Please read through these instructions completely to be sure you’re comfortable with this easy install process. Also check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, contact
Customer Service at 1-888-333-1376 (UK: 0800-056-2853).
Features
200 x 200mm
700 x 425mm
TV bracket expands to fi t TV hole patterns from 200 x 200mm up to 700 x 425mm
TV tilts up or down for the perfect viewing angle
Level adjustment creates a worry-free installation
Fully articulating arm creates 2-point movement for optimal viewing position
Adjustment knobs allow fi ngertip control or to restrict movement
Cover and cable tie holes hold cables along mount arm for a clean look
Mounting arm adjusts within the wall plate for optimal positioning
3
4
Dimensions
in.
[mm]
29.46
748.4
28.74
730.0
27.56
700.0
6.53
165.8
1.70
43.1
12.45
316.2
9.06
230.0
200mm to
425mm
0.34
8.8
15.00°
4.00°
13.46
[342.0]
in.
[mm]
2.00
50.8
R0.17
4.3
18.11
460.0
24.00
609.6
16.00
406.4
5
11.59
294.4
10.01
254.2
5
6
Supplied Parts and Hardware
WARNING:
This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!
NOTE:
Not all hardware included will be used.
STEP 1 Parts and Hardware
TV Screws
03 x4
M6 x 12mm
04 x4
M8 x 16mm
Vertical TV
Support
01 x1
05 x4
M4 x 12mm
08 x4
M4 x 35mm
06 x4
M6 x 20mm
09 x4
M6 x 35mm
Washers
07 x4
M8 x 20mm
10 x4
M8 x 35mm
Spacers
Interface
Nuts
Horizontal TV
Brackets
02 x2
M4
11 x4
M6 / M8
12 x4
13 x4
#8 Allen Nut
14 x4
STEP 2 Parts and Hardware
Wall Plate Template
15 x1
Wall Plate
16 x1
STEP 3-1 Parts and Hardware
Lag Bolts
5/16 in. x 2 3/4 in.
17 x4
Concrete Anchors
18 x4
Washers
19 x4
5 / 16 in.
Wall Plate Screws
Arm Assembly
20 x1
1/4-20 x 3/8 in.
21 x4
STEP 3-2 Hardware
Safety Screw
22 x1
1/4-20 x 3/4 in.
STEP 3-3 Hardware
Cable Ties
Cable Tie
23 x5
STEP 3-4 Parts and Hardware
25 x1
3/16 in.
Hex Keys
26 x1
7/32 in.
Cover Plates
24 x2
7
8
STEP 1 Attach Brackets to TV
1-1 Select TV Screw Diameter
Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter ( M4, M6, or M8 ) to use.
M4 M6 M8 a
1-2 Select TV Screw Length
If your TV has a flat back, use the shorter screws.
Spacers and longer screws are supplied to accommodate:
●
irregular / round back TVs
●
TVs with inset mounting holes
●
extra space needed for cables
b
CAUTION:
Verify adequate thread engagment with the screw or screw/spacer combination.
-
Too short will not hold the TV.
-
Too long will damage the TV.
FLAT BACK ROUND BACK INSET HOLES CABLES
Too Short
Correct
Too Long
1-3 Assemble TV Brackets
Slide horizontal TV brackets
02
onto the vertical TV support
01
as shown.
NOTE:
Position the slotted holes toward the outside for TV hole patterns larger than 250mm and toward the inside for hole patterns 250mm or less.
01
02
02
01
Screw posts
Angle the brackets
02
to clear the screw posts
TV Hole pattern greater than 250mm
Tilt the brackets
02
to nest the screw posts
TV Hole pattern 250mm or less
Slotted Holes
Screw Posts
02
Screw Posts
Slotted Holes
9
10
1-4 Secure TV Bracket Assembly
Center the horizontal TV brackets
02
and vertical TV support
01
over the hole pattern on your TV.
NOTE:
If the vertical TV support
01
is not centered, you may need to reposition the horizontal TV supports
02
(see previous step 1-3).
Secure the assembly with the four interface nuts
14
using hex key
25
.
02
02
01
25
14
1-5 Attach Bracket Assembly to TV
Attach the TV bracket assembly using either the short screw and washer or spacer, long screw and washer combination you selected for your TV.
02
02
01
a
Short screw and washer
03 04
05 06
07
11 12
b
Spacer, long screw and washer
13
08 09
10
11 12
11
STEP 2 Attach Wall Plate -
Wood Stud Option
CAUTION:
Avoid potential personal injuries and property damage!
●
Drywall covering the wall must not exceed 16 mm (5/8 in.)
●
Minimum wood stud size: common 51 x 102 mm (2 x 4 in.) nominal 38 x 89 mm (1 1/2 x 3 1/2 in.)
●
Minimum horizontal space between fasteners: 406 mm (16 in.)
1. Locate studs. Verify the center of the stud(s) using an awl, a thin nail, or an edge to edge stud finder.
NOTE:
For assistance in determining wall plate location, try our MountWizard ™ at
Simplicity.Sanus.com
2. Level the wall plate template
15
and mark the hole locations in the center of the studs.
NOTE:
TV shifts 254 mm (10 in.) to the right or left when in the home position. Consider this when selecting the location of your wall mount.
1
2
≤16 mm
(5/8 in.)
406-610 mm
(16-24 in.)
15
12
3. Drill pilot holes then remove the wall plate template
15
.
IMPORTANT
: Be sure to drill into the center of the stud.
IMPORTANT
: Pilot holes must be drilled to a depth of 75 mm (3 in.), using a 5.5 mm (7/32 in.) diameter drill bit.
4. Install the wall plate
16
using four lag bolts
17
and washers
19
. Tighten all lag bolts only until they are pulled firmly against the wall plate.
CAUTION:
Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts
.
4 3
75 mm
(3 in.)
5.5 mm
(7/32 in.)
15
17
19
16
13
STEP 2 Attach Wall Plate -
Solid Concrete or Concrete Block Option
CAUTION:
Avoid potential personal injuries and property damage!
●
Mount the wall plate directly onto the concrete surface
●
Minimum solid concrete thickness: 203 mm (8 in.)
●
Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
●
Minimum horizontal space between fasteners: 610 mm (24 in.)
NOTE:
For assistance in determining wall plate location, try our MountWizard ™ at
Simplicity.Sanus.com
1. Level the wall plate template
15
and mark the hole locations.
NOTE:
TV shifts 254 mm (10 in.) to the right or left when in the home position. Consider this when selecting the location of your wall mount.
2. Drill pilot holes into solid concrete. Never drill into the mortar between blocks.
1
IMPORTANT:
Pilot holes must be drilled to a depth of 75 mm (3 in.), using a 10 mm (3/8 in.) diameter drill bit.
2
15
610 mm
(24 in.)
15
75 mm
(3 in.)
10 mm
(3/8 in.)
14
3. Remove the wall plate template
15
and insert concrete anchors
18
.
CAUTION:
Be sure the anchors are seated flush with the concrete surface.
4. Install the wall plate
16
using four lag bolts
17
and washers
19
. Tighten all lag bolts only until they are pulled firmly against the wall plate.
CAUTION:
Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts
.
3
4
18
16
17
19
15
STEP 3 Attach TV to Wall Plate
3-1 Attach Arm Assembly to Wall Plate
1. Position the arm assembly
20
on the wall plate
16
by tilting the top into the wall plate channel, then rotating the bottom toward the wall.
NOTE:
TV shifts 254 mm (10 in.) to the right or left when in the home position. Consider this when selecting the location of your wall mount.
2. Secure using four wall plate screws
21
with hex key
25
.
1
2
25
16
21
Wall Plate Channel
16
20
3-2 Attach TV to Arm Assembly
HEAVY! You may need assistance with this step.
1. Hang the TV onto the arm assembly
20
by first hooking the top support, then resting the TV into place.
2. Lock the TV to the arm assembly
20
with safety screw
22
using hex key
25
.
1
CAUTION:
Avoid potential personal injury or property damage! This safety screw
22
must be installed to secure the TV onto the arm assembly
20
.
Top Support
2
20
20
22
25
17
18
3-3 Manage Cables
1. Remove the cable cover.
2. Use the supplied cable ties
23
to secure your cables in the positions shown.
3. Reattach the cable cover over the cables.
1
Cable Cover
2
3
23
Cable
Cover
Cable
Cover
3-4 Install Cover Plates
Store hex keys
25
and
26
in the slots provided, for future use.
NOTE:
Before installing the cover plates, use the hex keys to make any necessary adjustments as shown on pages 20 and 21.
Bow the middle of each cover plate
24
to slip the ends into the channels of the wall plate
16
.
26
25
24
24
25
16
24
19
TV Adjustments
ROTATE ADJUSTMENT
Your TV should adjust easily when moved, then stay in place.
If your TV is too loose or too tight, adjust either the top tension knob by hand or hex key
26
, or the top tension bolt using hex key
26
.
NOTE:
Once your TV is in place, tighten the tension knobs to prevent unwanted movement.
26
Tighten
Loosen
Tighten
26
Top Tension
Knob
Top Tension
Bolt
Loosen
TILT ADJUSTMENT
Your TV should adjust easily when moved, then stay in place.
If your TV is too loose or too tight, adjust the side tension knob by hand or use hex key
25
.
NOTE:
Once your TV is in place, tighten the tension knob to prevent unwanted movement.
Loosen
Side Tension Knob
Tighten
25
20
LEVEL ADJUSTMENT
Adjust the leveling of your TV by turning the level screw using hex key
25
.
Level Screw
TV LATERAL SHIFT
1. Remove the TV from the arm assembly
20
.
2. Remove the cover plates
24
and the four screws
21
from wall plate
16
.
3. Reposition the arm assembly on the wall plate.
4. Reattach the four screws (STEP 3-1) and replace the cover plates (STEP 3-4).
5. Hang the TV onto the arm assembly following STEP 3-2.
REMOVING THE TV
To remove your TV from the arm assembly
20
, disconnect all cables and then reverse the procedures in STEP 3-2.
20
25
24
21
20
16
25
24
21
ESPAÑOL
INSTRUCCIONES DE SEGURIDAD IMPORTANTES. CONSÉRVELAS. LEA TODO EL MANUAL ANTES DE UTILIZAR ESTE PRODUCTO.
1
Antes de comenzar, verifiquemos que este soporte sea perfecto para usted.
¿Su televisor pesa
más
de 56,7 kg (125 libras) incluyendo los accesorios?
(56,7 kg)
125 libras
No — ¡Perfecto!
Sí — Este soporte NO es compatible. Visite Simplicity.Sanus.com o llame al 1-888-333-1376 (Reino Unido: 0800-056-2853) para
encontrar un soporte compatible.
2
¿De qué está hecha su pared?
Tabiques de yeso con montantes de madera
Hormigón sólido o bloques de cemento
?
¿No está seguro?
¡Perfecto!
¡Perfecto!
Llame al 1-888-333-1376 (Reino Unido: 0800-056-2853)
3
¿Tiene todas las herramientas necesarias?
22
4
5,5 mm
(7/32'')
10 mm
(3/8'')
13 mm
(1/2'')
¿Listo para comenzar?
Lea estas instrucciones en su totalidad para estar seguro de sentirse cómodo con este fácil proceso de instalación. Consulte también el manual del usuario de su televisor para ver si existe algún requisito especial para instalar su televisor en la pared.
Si no entiende las instrucciones o si tiene dudas acerca de la seguridad de la instalación, del ensamblado o del uso del producto, contáctese con el servicio de atención al cliente al 1-888-333-1376 (Reino Unido: 0800-056-2853).
Descripción
La placa de sujeción se expande para adecuarse a televisores con patrones de orificios de 200 x 200 mm hasta 700 x 425 mm.
El televisor se inclina hacia arriba / abajo para obtener el ángulo de visualización perfecto.
El ajuste del nivel crea una instalación sencilla.
El brazo completamente articulado crea un movimiento de 2 puntos para una alcanzar una posición de visualización óptima.
El brazo se ajusta en la placa mural para un posicionamiento óptimo.
Las perillas de ajuste permiten el ajuste manual o limitar el movimiento.
La cubierta y los orificios para cinchos sujetan los cables a lo largo del brazo para un aspecto prolijo.
ESPAÑOL
VER PÁGINA 3
Dimensiones
VER PÁGINAS 4-5
Piezas y accesorios suministrados
VER PÁGINAS 6-7
ADVERTENCIA:
Este producto contiene piezas pequeñas que, si fuesen tragadas, podrían producir asfixia.
Antes de iniciar el ensamblaje, compruebe que todas las piezas estén incluidas y en buenas condiciones. Si faltan piezas o alguna está dañada, no devuelva el artículo al distribuidor; póngase en contacto con el servicio de atención al cliente. Nunca utilice piezas deterioradas.
NOTA:
No todos los accesorios incluidos deberán utilizarse.
23
ESPAÑOL
PASO 1 Colocar las placas de sujeción en el televisor
VER PÁGINAS 8-11
1-1 Seleccione el diámetro de los tornillos para el televisor
VER PÁGINA 8
Enrosque manualmente los tornillos en los encastres roscados del dorso del televisor a fin de determinar qué diámetro de tornillos
( M4, M6 o M8 ) utilizar.
1-2 Seleccione la longitud de los tornillos para el televisor
VER PÁGINA 8
Si el dorso del televisor es plano, utilice los tornillos cortos. Los espaciadores y los tornillos largos se proporcionan para:
●
los televisores con dorso irregular / redondeado
●
los televisores con orificios de montaje intercalados
●
dejar un espacio adicional para cables
PRECAUCIÓN:
Verifique que el tornillo o la combinación de tornillo y espaciador enrosquen correctamente.
Si el tornillo es demasiado corto no sostendrá el televisor. Si es demasiado largo dañará el televisor.
1-3 Arme las placas de sujeción del televisor
VER PÁGINA 9
Deslice las placas de sujeción horizontales
02
sobre el soporte vertical
01
como se muestra.
NOTA:
Ubique los orificios muescados hacia fuera para patrones de orificios de televisores mayores a 250 mm y hacia dentro para patrones de orificios de 250 mm o menos.
Coloque las placas de sujeción
02
en ángulo para liberar los postes de los tornillos. Incline las placas de sujeción
02
para encajar los postes de los tornillos.
1-4 Fije las placas de sujeción
VER PÁGINA 10
Centre las placas de sujeción horizontales
02
y el soporte vertical
01
sobre el patrón de orificios de su televisor.
NOTA:
Si el soporte vertical
01
no está centrado, necesitará reposicionar las placas de sujeción horizontales
02
(ver el paso 1-3).
Fije el módulo con cuatro tuercas interfaz
14
usando una llave hexagonal
25
.
1-5 Acople las placas de sujeción al televisor
VER PÁGINA 11
Acople el módulo de placas de sujeción para televisor usando ya sea la combinación de tornillo corto y arandela o espaciador, o tornillo largo
24 y arandela, que haya seleccionado para su televisor.
ESPAÑOL
PASO 2 Fijar la placa mural -
Opción para montantes de madera
VER PÁGINAS 12-13
PRECAUCIÓN:
Evite lesiones personales y daños materiales.
●
El yeso que recubre la pared no debe exceder los 16 mm (5/8'').
●
Tamaño mínimo del montante de madera: común 51 mm x 102 mm (2'' x 4'') nominal 38 mm x 89 mm (1 1/2'' x 3 1/2'').
●
Espacio horizontal mínimo entre los elementos de sujeción: 406 mm (16'')
NOTA:
Para ayudar a determinar la posición de la placa mural, pruebe nuestro MountWizard ™ en Simplicity.Sanus.com
1. Localice los montantes. Verifique el centro de los montantes con un punzón o un clavo delgado, o bien utilice un detector de bordes de montantes.
2. Nivele la placa mural
15
y marque la ubicación de los orificios en el centro de los montantes.
NOTA:
El televisor se desplaza 254 mm (10”) a la derecha o la izquierda cuando se encuentra en la posición inicial. Considere esto a la hora de seleccionar la ubicación de su soporte mural.
3. Realice los orificios guía y retire la placa mural
15
.
IMPORTANTE
: Asegúrese de perforar el centro del montante.
IMPORTANTE
: Los orificios deben realizarse con una mecha de 5,5 mm (7/32'') de diámetro hasta una profundidad de 75 mm (3'').
4. Instale la placa mural
16
usando cuatro tornillos tirafondo
17
y arandelas
19
. Ajuste los tornillos tirafondo solamente hasta que queden firmes contra la placa mural.
PRECAUCIÓN:
El uso indebido podría reducir la capacidad de retención de los tornillos tirafondo.
NO ajuste en exceso los tornillos tirafondo
.
PASO 2 Fijar la placa mural -
Opción para hormigón sólido o bloques de cemento
VER PÁGINAS 14-15
PRECAUCIÓN:
Evite lesiones personales y daños materiales.
●
Instale la placa mural directamente sobre la superficie de hormigón.
●
Espesor mínimo del hormigón: 203 mm (8'')
●
Tamaño mínimo del bloque de cemento: 203 x 203 x 406 mm (8'' x 8'' x 16'')
●
Espacio horizontal mínimo entre los elementos de sujeción: 610 mm (24'')
25
ESPAÑOL
PASO 2 Fijar la placa mural -
Opción para hormigón sólido o bloques de cemento (continuación)
NOTA:
Para ayudar a determinar la posición de la placa mural, pruebe nuestro MountWizard
™
en Simplicity.Sanus.com
1. Nivele la placa mural
15
y marque la ubicación de los orificios.
NOTA:
El televisor se desplaza 254 mm (10”) a la derecha o la izquierda cuando se encuentra en la posición inicial. Considere esto a la hora de seleccionar la ubicación de su soporte mural.
2. Realice los orificios guía en el hormigón sólido. Nunca perfore el cemento que une los bloques.
IMPORTANTE:
Los orificios guía deben realizarse con una mecha de 10 mm (3/8'') de diámetro hasta una profundidad de 75 mm (3'').
3. Retire la placa mural
15
e introduzca los anclajes para cemento
18
.
PRECAUCIÓN:
Cerciórese de que los anclajes queden nivelados respecto de la superficie de hormigón.
4. Instale la placa mural
16
usando cuatro tornillos tirafondo
17
y arandelas
19
. Ajuste los tornillos tirafondo solamente hasta que queden firmes contra la placa mural.
PRECAUCIÓN:
El uso indebido podría reducir la capacidad de retención de los tornillos tirafondo.
NO ajuste en exceso los tornillos tirafondo
.
PASO 3 Fije el televisor a la placa mural
VER PÁGINA 16
3-1 Fijar el módulo del brazo a la placa mural
VER PÁGINA 16
1. Ubique el módulo del brazo
20
sobre la placa mural
16
inclinando la parte superior dentro del canal de la placa mural, y rotando luego la parte inferior hacia la pared.
NOTA:
El televisor se desplaza 254 mm (10”) a la derecha o la izquierda cuando se encuentra en la posición inicial. Considere esto a la hora de seleccionar la ubicación de su soporte mural.
2. Fije usando los cuatro tornillos
21
con la llave hexagonal
25
.
3-2 Acoplar el televisor al módulo del brazo
VER PÁGINA 17
¡ELEMENTO PESADO! Es posible que necesite ayuda en este paso.
26
1. Para colgar el televisor del módulo del brazo
20
, enganche el soporte superior y luego apoye el televisor en su lugar.
2. Fije el televisor al brazo
20
con un tornillo
22
usando una llave hexagonal
25
.
PRECAUCIÓN:
Evite el riesgo de lesiones y daños materiales.
Este tornillo de seguridad
22
debe instalarse para fijar el televisor al ensamblaje del brazo
20
.
ESPAÑOL
3-3 Organizar los cables
VER PÁGINA 18
Retire la cubierta de los cables. 2. Utilice los cinchos sujetacables provistos
23
para fijar los cables en las posiciones que se muestran.
NOTA:
Antes de instalar las tapas, use las llaves hexagonales para realizar cualquier ajuste necesario, como se muestra en las páginas 20 y 21.
Vuelva a colocar la cubierta de los cables por sobre los cables.
3-4 Instalar las tapas
VER PÁGINA 19
Guarde las llaves hexagonales
25
y
26
en las ranuras, para su uso en el futuro.
Arquee la parte media de cada tapa
24
para introducir los extremos en los canales de la placa mural
16
.
Ajustes del televisor
VER PÁGINAS 20-21
AJUSTE DE LA ROTACIÓN
El televisor debe acomodarse fácilmente al moverlo, y luego quedar en su lugar. Si el televisor está demasiado suelto o demasiado ajustado, puede o bien ajustar la perilla de tensión superior manualmente o con la llave hexagonal
26
, o bien ajustar el perno de tensión superior con la llave hexagonal
26
.
NOTA:
Una vez que el televisor esté en su lugar, ajuste las perillas de tensión para evitar un movimiento indeseado.
AJUSTE DE LA INCLINACIÓN
El televisor debe acomodarse fácilmente al moverlo, y luego quedar en su lugar. Si el televisor está demasiado suelto o demasiado ajustado, ajuste la perilla de tensión lateral manualmente o con la llave hexagonal
25
.
NOTA:
Una vez que el televisor esté en su lugar, ajuste las perillas de tensión para evitar un movimiento indeseado.
AJUSTE DEL NIVEL
Ajuste el nivel de su televisor girando el tornillo de ajuste de nivel con la ayuda de la llave hexagonal
25
.
DESPLAZAMIENTO LATERAL DEL TELEVISOR
1: Retire el televisor del módulo del brazo
20
. 2: Retire las tapas
24
y los cuatro tornillos
21
de la placa mural
16
. 3: Vuelva a ubicar el módulo del brazo sobre la placa mural. 4: Vuelva a colocar los cuatro tornillos (PASO 3-1) y las tapas (PASO 3-4). 5: Cuelgue el televisor del módulo del brazo siguiendo las instrucciones del PASO 3-2.
EXTRACCIÓN DEL TELEVISOR
Para extraer el televisor del módulo del brazo
20
, desconecte todos los cables y luego revierta el procedimiento descrito en el PASO 3-2.
27
Thank you for choosing Sanus! Please take a moment to let us know how we did:
Call us: 1-888-333-1376 (UK: 0800 056 2853)
Email us: [email protected]
Leave a review: www.simplicity.sanus.com
Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.
Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy,
©2013 Milestone AV Technologies, a Duchossois Group Company. All rights reserved. Sanus is a division of Milestone.
All other brand names or marks are used for identifi cation purposes and are trademarks of their respective owners.
SANUS
• 6436 City West Parkway • Eden Prairie, MN 55344 USA 6903-002018 03
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project