ADV38

10.1” OVERHEAD LED BACKLIT

LCD MONITOR WITH

DVD PLAYER

ON OFF AUTO

R

OPERATION

MANUAL

Important Notice

I nstallation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or

D pillars of the vehicle. Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal injury to vehicle occupants. If you have any questions regarding wire routing in a vehicle, please contact Audiovox Technical Support at 1-800-225-6074.

When connecting power and ground in a mobile video installation ensure that the ACC wire is fused at the point where it is connected to the vehicle ACC wiring. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the mobile video product.

An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle's parking brake is applied.

An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver's seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle.

Warnings

•

•

Do not use any solvents or cleaning materials when cleaning the video monitor.

Do not use any abrasive cleaners, they may scratch the screen.

•

•

Use only a lightly dampened lint free cloth to wipe the screen if it is dirty.

Lock the LCD screen in the fully closed position when not in use.

• Before putting on headphones always adjust the volume setting to the lowest position.

• Remember to leave the dome light switch in the off or auto positions when the vehicle is unattended, as the dome lights, if left on, can drain the vehicle's battery.

•

•

Do not put pressure on the screen.

Caution children to avoid touching or scratching the screen, as it may become dirty or damaged.

Patented, refer to www.voxxintl.com/company/patents

I

Congratulations

Congratulations on your purchase of the ADVENT ADV38

DVD Player with Drop-Down Video / Monitor. The ADV38 has been designed to give you and your family many years of video entertainment in the mobile environment. Please read the directions that follow to familiarize yourself with the product to ensure that you obtain the best results from your equipment.

Please note:

Installation options vary, see the individual owner's manuals for each component in your system to obtain a full understanding of each component's operation.

Safety Precaution

For safety reasons, when changing video media it is recommended that the vehicle is not in motion, and that you do not allow children to unfasten seat-belts to change video media or make any adjustments to the system. System adjustments can be accomplished using the remote control, while seat-belts remain fastened. Enjoy your ADVENT entertainment system but remember the safety of all passengers remains the number one priority.

FEATURES

• 10.1” TFT (Thin Film Transistor) Active Matrix LCD (Liquid

Crystal Display) Monitor

• LED Backlighting

• Built-in DVD Player.

• OSD (On Screen Display) for Control of Picture Quality and

Functions.

• Single Channel Infrared Transmitter for IR Wireless Headphones.

•

GAME).

• Dome Lights with Built-in Three Way Switch.

• Built-in 16 Channel Wireless FM Modulator.

• Last Position Memory for DVD.

• Screen Mode Selection (4:3, 16:9).

• Wireless Game Controller.

• Full Function Remote Control.

• Backlit Controls.

• 1 AV Output via RCA Pigtail.

• Pla ys s

II

CONTROLS AND INDICATORS DIAGRAM (FRONT VIEW)

6

5 4 3 2 1

ON OFF AUTO

-

-

Press the STOP button once : Stops playback . P ressing the PLAY button will resume playback from where movie was stopped.

Press the STOP button the twice : P ressing the PLAY button will resume playback from the beginning of the

DVD.

7

8

9

This control is used for ejecting discs from the disc compartment. (

Note:

Disc can be ejected with the unit turned

Off. Vehicle ignition must be in Run or ACC position

). After the Disc is removed the unit will turn Off in 15-20 seconds.

3. Source Select

Use to select one of the four sources:

GAME.

10

11

This control is used to start playback of a disc.

5. POWER ( ) Control

Used to turn the system on/off..

6. Dome Lights

Provide additional interior illumination.

7. Infrared Transmitter and Sensor

Transmits audio to wireless headphones, allows the remote control to operate the ADV38 and to control other accessories in the system.

12

1

8. Three Position Dome Light Switch

ON

OFF

- Turns on the dome lights.

- The dome lights will not turn on in this position.

AUTO

- Automatically switches on the dome lights in

Conjunction with the vehicle's interior illumination.

9. Ventilation Openings

10. LCD Cut Off Switch

Used to turn off the LCD monitor when in the closed position.

11. LCD Panel

12. Screen Release

.

Press to release the screen.

(

CONTROL FUNCTION DESCRIPTION

BACK VIEW)

1

1. REAR IR SENSOR

Transmits audio to wireless headphones, allows the remote control to operate the ADV38 and to control other Accessories in the system.

CONTROL FUNCTION DESCRIPTION

(SIDE VIEW)

1

2 3 4

2

1. DVD Disc Insertion Slot

For loading and removing discs. Unit will turn ON and load disc when disc is inserted. Insert disc with label side facing up.

Note:

Disc slot will be lit when unit is turned OFF for easy loading at night.

2. HEADPHONE JACK

Allows the use of wired headphone with a 1/8” (3.5mm) plug for listening to the audio output

3. AUX IN

The Jack is used for audio and video input.

4. USB INPUT

FOR USB MEMORY DEVICE

Allows for the connection of an USB or memory device.

TURNING THE UNIT ON OR OFF

1. Pushing in the Screen Release button will unlock the LCD screen and it will drop down slightly. Pivot the screen downward until a comfortable viewing angle is reached. The hinge friction will hold the screen in position while the system is in use.

2. Pressing the power button* on the unit or the remote control will turn the system on and off. When in use the internal backlighting will illuminate the controls.

3. After the unit has been turned on and is displaying a picture, adjust the viewing angle, by pivoting the screen to optimize the picture quality.

4. Remember to turn the unit off and pivot the LCD to the locked position when not in use.

*Note:

Unit will turn On automatically when a Disc is inserted

Power

ON/OFF

Button

Remote Sensor

Infrared Transmitter

ON OFF AUTO

Screen Release

Rear IR Sensor

3

OVERHEAD DOME LIGHTS

The Dome Lights integrated into the unit are controlled by a three position slide switch. Sliding the switch to the ON position will turn the lights ON. The OFF position will prevent the lights from turning ON with the vehicle's interior lighting and the auto position will allow the lights to turn ON and OFF with the vehicle's interior lighting. Refer to the Installation Guide for wire connections. Do not leave the vehicle unattended with the dome light switch in the ON position, as this could result in a discharged battery.

REAR IR SENSOR

The ADV38 incorporates two infrared remote sensors to relay signals to the unit when the remote control is pointed at the remote sensor.

ACCESSORIES

WIRELESS HEADPHONES

The ADV38 includes a built-in infrared transmitter for use with the supplied wireless headphones. The headphone volume is adjusted using the controls on each headset. Any number of wireless headphones may be used but they must be used within a line of sight from the transmitter, as infrared transmissions, like visible light travel only in a straight line. See the documentation accompanying your wireless headphones.

WIRED HEADPHONES (OPTIONAL)

There is one 1/8” headphone jack on the unit that can be used with any standard wired stereo headphones with a 1/8” plug. This jack is controlled by the volume up/down buttons on the remote control.

4

SOURCE FEATURE

AV1

The AV1 input may be connected to a external video source, video game system, or other audio/video devices. To access the audio/video inputs, turn the unit on and press the S (source) button on the ADV38 or the Source button on the remote control until

"AV1" is displayed on the screen. Turn the video source component on with its power button or remote control and it is now ready to play the audio and video signals from the source connected .

Note:

AV1 sources are available only if pre-installed during your video product installation.

AUX

The AUX input may be connected to an external video source, video game system, or other audio/video devices. To access the audio / video inputs, turn the unit on and press the S (source) button on the ADV38 or the Source button on the remote control until "AUX" is displayed on the screen.

Note:

The ADV38 can be used with many currently available portable media players that have RCA output cables. Plug the RCA outputs of the portable media player into the RCA connectors on the A/V adapter cable supplied with your ADV38 and plug the 3.5mm plug on the other end of the adapter into the into the AUX IN jack on the side of the ADV38.

Your portable media player may need a special adapter from the manufacturer to be able to play video on the ADV38. Check the owner’s manual supplied with your portable media player to see if one is available.

GAME

Press the unit’s S (source) button until the screen displays GAMES. The GAME selection is controlled by wireless game controller.

5

USING THE WIRELESS GAME CONTROLLER

The Game Controller transmits to the ADV38 with two infrared transmitters located on the front of the Game Controller. The

Game Controller must be pointed toward the unit for correct operation.

Press the source button on the remote control or the unit until

“GAME” is displayed.

GAME CONTROLLER FUNCTIONAL DESCRIPTION

1. Install two AAA batteries in the Game Controller. Observe the correct polarity.

2. Use the ON/OFF selector switch to turn on the Game

Controller. A list of ten games will be displayed.

3. Use the A button (page up) or B button (page down) to display the three pages of games (1-10, 11-20, 21-30). Then use the direction buttons to move the arrow to the desired game. Press

Start to select the game.

4. Press Start to begin the game. Press Start again at any time to pause the game.

5. Press RESET to return to the game list.

6. Use the ON/OFF selector switch to turn off the Game

Controller after use

.

6

Bottom Side of Game Controller

Battery case

REMOTE CONTROL OPERATION

CR2025

Initial Use

When purchased the remote control has a battery installed with a

Pull Tab to prevent battery discharge. Remove the Pull Tab before attempting to use the remote.

Battery Replacement

1. Remove the battery holder.

2. Insert the battery into the battery holder and insert the battery holder into the remote. Be sure to observe the correct polarity.

3. Align the battery holder with the remote control and push until the holder clicks.

7

MAIN FUNCTION OPERATION

9

8

10

11

12

13

1

4

5

2

3

6

7

14

15

POWER

M1

SOURCE

TV

DVD SOURCE

SYSTEM MENU

PIX

M2

DVD

VOLUME

MUTE

DISC MENU ZOOM

REPEAT

DISPLAY

ENTER

SETUP SUBTITLE

DVD SOURCE

AUDIO

FMM

ON/OFF

IRT

ON/OFF

29

28

27

26

25

24

23

22

21

20

19

18

17

16

*

**

Function control is available on the unit and the Remote Control.

Function not available in this model.

1. POWER Button*

Press this button to turn the unit ON and OFF.

2.

SOURCE Button*

Each time the button is pressed, the audio /video source will change in the following sequence: DVD/USB > AV1 > AV2 > GAME.

3.

TV Mode Select Button**

Switches certain function keys on the remote control for TV.

4.

DVD Source

This button is only activated when remote control is in DVD mode. Each time the button is pressed one of the source (DVD or USB) will be selected. If the Card Reader and USB are not plugged in, it will remain on DVD Source. Press to change source in sequence of DVD > USB.

5.

PIX Button (Picture Select)*

Each time this button is pressed, the on screen picture adjustment displays the “adjustment bar” for BRIGHTNESS, CONTRAST,

COLOR, TINT or RESET. Once the desired adjustment bar is displayed, use the VOLUME(+)/ VOLUME(–) button to adjust the setting.

The display will automatically turn off if no adjustments are made within 6 seconds, or is any other button is pressed.

6.

SYSTEM MENU Button

Allow the user to access the system menu. Press cursor ( pq

) buttons to select desired screen mode, OSD language and source default on power up.

7.

CURSOR / CHANNEL UP DOWN (

pqtu

) **

Use these buttons to navigate the menu selections on the screen.

Use the CH p to increase the channel number and use CH q to decrease the channel number. **

8

8.

ENTER Button

Used to implement a selected setting or menu option.

9.

DISPLAY

Press to display current disc information while the disc is playing. Press cursor ( pq

) buttons to select the Title or Chapter.

For Title/Chapter selection use the numeric buttons to enter the desired Title Chapter selection.

10.

SCAN BACKWARD (

7

) Button

Press to search in backward direction. Press repeatedly to change the search speed from 2, 4, 8, and 16 times then normal speed.

11.

Press to activate the play mode when a disc is loaded in the disc compartment.

12.

PREVIOUS (

9

) Button

Press to return to the previous chapter or track.

13.

Allows the user to pause the playback. Pressing pause again or Play Button will resume normal playback.

14.

NUMBER Buttons

Allow the user to enter numbers 0 to 9 for selection of selection of CD tracks, DVD chapters or password.

15. FMM ON / OFF Button*

Turns the wireless FM Modulator on or off.

16. IRT ON/OFF Button

Turns the Infrared Transmitter IRT ON or OFF for IR Wireless Headphones. Pressing M1 then IRT ON/OFF will control the IR Transmitter for M1.

9

17.

NEXT (

:

) Button

Press to skip to the next chapter or track

18. STOP (

<

) Button*

Press to stop playback.

19.

SCAN FORWARD (

8

) Button

Press to search in a forward direction. Press repeatedly to change the search speed from 2, 4, 8, and 16 times then normal speed.

20.

AUDIO Button

Press to display and select the available AUDIO languages in DVD mode. Each time you press the button, the language changes.

Note:

The languages for audio vary from disc to disc.

21.

SETUP Button

Press to display the Setup Menu which allows the user to change the DVD player options such as LANGUAGE, VIDEO, RATING &

MISC. Refer to the settings and adjustments section for more information.

22.

SUBTITLE Button

Press to display and select the available subtitle language in DVD mode. Each time you press the button, the subtitle language changes.

Note:

The type and number of languages for subtitle vary from disc to disc.

23.

REPEAT Button

Allows the user to repeat a selected title, chapter, or track.

24.

DISC Menu Button

Allows the user to access the DISC’s menu mode.

10

25. ZOOM Button

Press this button to enlarge the picture when playing a DVD disc.

Press ZOOM button

Once

DVD player perform

Q1- Enlarge the picture 2 times of the original size

Second

Third

Forth

Q2- Enlarge the picture 3 times of the original size

Q3- Enlarge the picture 4 times of the original size

Q off- Picture is returned to original size

26.

VOLUME DOWN (–) or UP (+)*

Press to decrease or increase the level of the wired headphone volume.

27.

DVD Mode Select Button

Switches certain function keys on the remote control for DVD function.

28.

MUTE Button

Press this button to mute the audio for wireless FMM, IR HEADPHONES and wired headphones.

Pressing the button again restores the sound to the previously set level.

29.

This button is used to eject the disc.

11

SYSTEM MENU ADJUSTMENT

The System Menu contains features and options that let you customize your system to change the screen mode display, OSD language and source default.

1) Press the SYSTEM MENU button on the remote, the main page of the system menu will appear on screen.

2) Use the cursor buttons p or q to select the desired item in the main page and press the ENTER button to select.

3) The sub menu will appear on screen.

4) Use the cursor buttons p or q to select an item in the sub menu and then press the ENTER button to select.

5) Press the System Menu button to exit System Menu.

Note:

System Menu can be controlled via Remote Control only. (Items selected in the menu will have a green background)

PICTURE CONTROL

When watching program, the picture quality can be adjusted to suit individual preferences.

1) Each time this button is pressed, the on screen picture adjustment displays the “adjustment bar ” for

COLOR, TINT

or

RESET.

BRIGHTNESS, CONTRAST,

2) Once the desired adjustment bar is displayed, use the Volume (+) / Volume (-) button to adjust the setting. The display will automatically turn off if no adjustments are made within 6 seconds, or is any other button is pressed.

3) Press the q button four times to select RESET, then press either Volume (-) or the Volume (+) button on the remote or the main unit.

All of the picture settings (

BRIGHTNESS, CONTRAST, COLOR

and

TINT

) will return to the factory setting.

SYSTEM MENU

PICTURE CONTROL

FMM

OSD LANGUAGE

SOURCE DEFAULT DVD

SCREEN MODE

PICTURE CONTROL

BRIGHTNESS

CONTRAST

COLOR

TINT

RESET

12

FMM SELECT

This function allows the user to listen to audio through the vehicle’s radio.

FMM ON - Turns the FM Modulator on.

FMM OFF - Turns the FM Modulator off.

FMM SELECT - Selects the wireless FM Modulator frequency (CH1 - 88.1MHz, CH2 - 88.3MHz, CH3 - 88.5MHz, CH4 - 88.7MHz,

CH5 - 88.9MHz, CH6 - 89.1MHz, CH7 - 89.3MHz, CH8 - 89.5MHz, CH9 - 89.7MHz, CH10 - 89.9MHz, CH11 - 90.1MHz,

CH12 - 90.3MHz, CH13 - 90.5MHz, CH14 - 90.7MHz, Ch15 - 90.9MHz, CH16 - 91.1MHz).

SYSTEM MENU

PICTURE CONTROL

FMM

OSD LANGUAGE

SOURCE DEFAULT DVD

SCREEN MODE

FMM

FMM ON

FMM OFF

FMM SELECT

To choose a FM frequency for audio playback through your vehicle’s radio:

1. Access the System Menu. Press the TV button on the remote control, then press the SYSTEM MENU button. The SYSTEM MENU screen appears.

2. Press the q cursor button to highlight FMM, then press the ENTER button. The FMM screen appears.

3. Press the q cursor button to highlight FMM SELECT, then press the ENTER button. The FMM SELECT screen appears.

FMM SELECT

88.1 Mhz 89.7 Mhz

88.3 Mhz 89.1 Mhz

88.5 Mhz

88.7 Mhz

88.9 Mhz

89.1 Mhz

89.3 Mhz

89.5 Mhz

90.1 Mhz

90.3 Mhz

90.5 Mhz

90.7 Mhz

90.9 Mhz

91.1 Mhz

4. Press the pqt or u cursor buttons to select a frequency not used by a radio station in the area. Press the ENTER button to select the highlighted frequency. Tune your vehicle’s radio to the selected frequency.

5. Press the DVD button to restore control of the DVD functions.

13

OSD LANGUAGE

This function allows the user to select the language for the on-screen display.

The user can either select English, Spanish, French, German for the OSD language.

SYSTEM MENU

PICTURE CONTROL

FMM

OSD LANGUAGE

SOURCE DEFAULT DVD

SCREEN MODE

SOURCE DEFAULT DVD

This function allows the user to set the system default source to DVD (via

System Menu).

Notes:

•

If selected default source is set to DVD every time the unit’s power is cycled with the source set to something other then DVD, the unit will power up and automatically switch the source over to DVD.

•

Unit will be set to Last Memory on as the default mode of operation.

• Selection of Source default can only be made from within the system menu.

SYSTEM MENU

PICTURE CONTROL

FMM

OSD LANGUAGE

SOURCE DEFAULT DVD

SCREEN MODE

SCREEN MODE

This function allows the user to change the screen format (aspect ratio

4:3, 16:9)

To select the screen aspect ratio format:

1. Highlight SCREEN MODE and press the ENTER button to access the submenu.

2. Press the Up or down cursor buttons ( p or q

) to select from 4:3 or 16:9.

Press ENTER button to confirm the setting.

14

SYSTEM MENU

PICTURE CONTROL

FMM

OSD LANGUAGE

SOURCE DEFAULT DVD

SCREEN MODE

OSD LANGUAGE

ENGLISH

SPANISH

FRENCH

GERMAN

SOURCE DEFAULT DVD

ON

OFF

4:3

16:9

SCREEN MODE

SETUP MENU SETTINGS AND ADJUSTMENTS

The Setup Menu contains features and options that let you customize your DVD player. For example, you can set a language for the onscreen display or prevent DVD playback for children.

Using the Setup Menu

1. Press the SETUP button on the remote. The Setup Menu appears on the screen as shown per diagram.

2. To set the desired option, move the highlight into the setup area using the cursor button u

.

3. After entering the setup area, highlight the desired option using the cursor button or .

4. Press u to open the sub menu that contains the different options available. Press or to highlight the desired option, and press ENTER to confirm the selection.

Language

Video

Rating

Misc

OSD Language

Subtitle

Audio

5. Repeat steps 3~4 to set the options that reside on the same Setup Page.

6. To change to another Setup page, press t to position the highlight back on the icon side of the Setup Page. Then, repeat steps 2~5.

: English

: Off

: English

Exiting the Setup Menu

Press the SETUP button again.

LANGUAGE SETUP

Language for On-Screen Display

OSD MENU: The OSD MENU setup allows you to select the language for the on-screen display.

The user can either select English, French, Spanish, German or Italian for the OSD language.

Language

OSD Language

Video

Rating

Subtitle

Audio

Misc

English

French

Spanish

German

Italian

15

SUBTITLE SETUP

Select "SUBTITLE" desire using using pq button, then press u button to enter the Sub menu. Select the subtitle you pq button, then press “ENTER” to confirm the setting. Press t button to return.

Note: The subtitle selection is only available for discs that are recorded in the above listed languages. If the selected, language is not available, the player will play and display on the screen the original language contained in the disc.

Language OSD Language

Subtitle Video

Rating

Audio

Misc

English

French

Spanish

German

Italian

Chinese

Japanese

Thai

Off

AUDIO SETUP

Select using

"AUDIO" pq using pq button, then press u button to enter the Sub menu. Select the audio you desire button, then press “ENTER” to confirm the setting. Press t button to return.

Note: The audio selection is only available for discs that are recorded in the above listed languages. If the selected, language is not available, the player will play and display on the screen the original language contained in the disc.

Language OSD Language

Subtitle Video

Rating

Audio

Misc

English

French

Spanish

German

Italian

Chinese

Japanese

Thai

VIDEO SETUP

TV Display

The TV DISPLAY setup allows you to set the screen aspect ratio.

4:3 - This displays the wide picture with black bands on the upper and lower portions of the screen.

16:9 - This displays a wide picture with black bands on the upper and lower portion of the screen.

The bandwidth will vary, depending on the aspect ratio of the disc.

TV Type

The TV Type setup allows you to select the system to fit to the color system of the TV to be connected.

NTSC - Select this type for NTSC TV

PAL - Select this type for PAL TV

16

Language TV display

TV type

Video

Rating

Misc

4:3

16:9

RATING SETUP

Rating

This item allows you to limit the content of movie playback from G to Adult.

The lower the value, the more strict the control.

1. G

2. PG

3. PG – 13

4. R

5. NC – 17

6. Adult

Language

Parental : 6.Adult

Change Password Video

Rating

Misc

Language

Parental

Video

Rating

: 6.Adult

Change Password

Enter Password

Misc

The rating level can only be changed when the correct password is entered. The first time the parental control is entered, use the cursor u button to enter parental mode, key in the default password (3308) and press ENTER. Press the ENTER button again to open the parental level sub menu. Select the desired level and press ENTER. To change the password to your own password highlight “Change Password” and press

ENTER. Enter the default password (3308) and press ENTER. Press the ENTER button again and key in a new four digit password. Press

ENTER button to end the process.

Note:

The Default Password is 3308. This password is always accepted even after a new password has been entered. To avoid the possibility of others using the default password to set the parental level and change the password, record this default password in another area and delete it from this manual. The restriction of viewing disc content by younger users may be available on some disc but not on others.

Misc SETUP

Select "M ISC ” using pq button, then press u button to enter the Misc menu.

Language

Load Factory

Screen Saver : On Video

Rating

Misc

17

Load Factory

This option allows you to reset all options to factory settings.

Note:

This function will not affect the Rating control settings.

Language

Video

Load Factory

Load Factory

Screen Saver

Yes No

Rating

Misc

Screen Saver

This option allows the operator to set the Screen saver mode.

ON - Screen saver will appear

OFF - Screen saver will not appear

Note:

The DVD player will enter Screen Saver mode if the unit is inactive for approximately 2 minutes.

Language Load Factory

Screen Saver Off

Video

Rating

On

Misc

Playing DVDs

1. Press the DISPLAY button on the remote control to display the status banner. The banner includes title, chapter, angle, audio, subtitle and

2.

time.

Title Selection

Press numeric (0~9) buttons to initiate a change of title selection. Then press ENTER to implement the selection.

3.

Chapter selection

Press numeric (0~9) buttons to initiate a change of chapter selection. Then press ENTER to implement the selection.

USB Memory Devices

1. The System will detect the insertion of the USB device automatically if no disc is loaded. The system only auto detects the first media inserted (USB drive); the second media source can be manually selected by pressing the DVD source button on the remote control when the unit is in DVD mode.

2. When a disc is inserted, the system will switch to DVD mode immediately regardless of a USB media is currently playing.

3. The DVD source (DVD or USB) can only be changed if the DVD is stopped.

4. This system cannot support more than 2 memory partitions on the USB thumb drive.

Note:

The system will always default to the DVD when the system detects a disc in the DVD player.

18

Playing MP3 Discs

MP3 is a format for storing digital audio. An audio CD-quality song can be compressed into the MP3 format with very little loss of quality, while taking up much less space. CD-R discs that have been encoded in MP3 format can be played on DVD player. The DVD player plays the songs in the order they were burned on to the disc. When playback is started the elapsed time of the track that is playing will be displayed.

Selecting Folders and Songs

When a device containing MP3 files is loaded in the player, the navigation menu appears automatically.

1. Press or to move the highlight to the desired folder (if present) on the left side of the menu and press ENTER. The songs in the folder will be displayed on screen.

2. Press or to move the highlight to the desired track containing the song and press ENTER to begin track playback.

Skipping Songs

Use the Next (

:

) button on the remote control to move to the next song. Use the Previous (

9

) button to move to the previous song.

Selecting a Play Mode

Filter (For MP3 & JPEG only)

Filter Mode enables or disables the display of files contained on the media based on their file extension.

The filter function applies to the following formats:

Audio -

Audio data format (MP3, WMA)

Photo -

Photo data format (JPEG)

Video -

Video data format (MPEG , )

1/12

001

002

003

004

005

006

/

00:00:01

Filter

Audio

Flat Mode

Repeat :

Photo

Video off

Flat Mode:

play the entire disc

This mode is always on (default). During the Flat Mode, all the data folder with MP3, JPEG and movies will be played in sequence. If the Flat Mode function is off, it will only play the selected folder; other folders are disabled.

1/12

001

002

003

004

005

006

/

00:00:01

Flat Mode

Repeat : Off

Mode : Normal

19

Repeat:

play repetitively

Repeat function has 4 options : Off, Single, Folder, All. Move cursor to Repeat function and press ENTER,

Each time ENTER is pressed the unit will cycle through the available options. Off/Single/Folder/All are displayed in that order. Repeat default is Off;

Off

Single

Folder

All

Turn off repeat function

Repeat the song being played until STOP is pressed.

Play all songs in a folder repetitively

Play all songs on the disc repetitively

1/12

001

002

003

004

005

006

/

00:00:01

Flat Mode

Repeat : Off

Mode : Normal

Mode

: play mode

The Mode function has 4 options: Normal, Shuffle, Random and Music Intro. Move cursor to the Mode function area and press ENTER repeatedly till the desired mode is displayed. Normal/Shuffle/Random/

Music Intro are displayed in that order. The Mode function default is Normal.

Normal:

Shuffle:

Play all songs in folder once.

Play songs in a folder in a shuffle order. Each song in the folder is played only once.

Random:

Play songs in a folder in a random order. Each song in a folder is’t only be played once.

Music Intro:

Play each song in order in the folder for 10 seconds The purpose of the Music Intro function is to provide the user with a sample of each song for 10 seconds, thereby making it easy to select and listen to a favorite song.

1/12

001

002

003

004

005

006

/

00:00:01

Flat Mode

Repeat : Off

Mode : Normal

Add to program

Method:

To add the selected songs into Browser view, make sure disc playback is off. Move cursor to

“Edit Mode” function and press ENTER. After Edit Mode” is selected, move cursor to songs list and select the songs which will be compiled and press ENTER. A check mark appears to the left of the selected song;

1/12

001

002

005

006

/

00:00:01

Edit mode

Program view

Add to program

to add the selected songs to the program, move cursor to the “Add to Program” function and press ENTER.

The selected songs is added into a new program list and the check mark will disappear on play list, move cursor to “Program View” function and press ENTER to browse the songs in the program. Press play button

003

004

Album:------------

to play the selected songs.

Note:

Edit Mode, Program View or Add to Program functions are relationship related when selecting the preferred song add to the songs list.

20

Clear program

Method:

To clear the selected song files, press the STOP button twice during playback mode. Move the cursor to the “Edit Mode” function and press ENTER. After “Edit Mode” is selected, move cursor to selected songs list and select the songs you want to delete. Press ENTER and a check mark will appear to the left of the selected song. Move the cursor to clear program and press ENTER, the selected songs will be deleted from the play list.

1/12 /

00:00:01

001

002

003

004

005

006

Album:------------

Edit mode

Browser view

Clear program

21

DVD BASICS

To get the optimum use out of the DVD section, make sure you read this section completely.

DVD Region Code

The DVD player is preset to a region code at the factory depending on where the DVD player is sold. DVDs from a different region cannot be played in this unit and the unit will display "WRONG REGION”

Region 1- USA, Canada

Region 2- Japan, Europe, South Africa, Middle East,

Greenland

Region 3- S. Korea, Taiwan, Hong Kong, Parts of

South East Asia

Region 4- Australia, New Zealand, Latin America

(including Mexico)

Region 5- Eastern Europe, Russia, India, Africa

Region 6- China

22

Types of Discs your DVD Player will play

• DVD* disc - DVD discs which contain video.

•

•

Audio discs - Audio CDs contain musical or sound content only.

MP3 discs - A disc that contains audio files (for example, a CD-R with downloaded MP3 files).

* This system is capable of playing most recordable DVD formats. However, due to the variety of disc manufacturers and software, playback cannot be guaranteed.

Loading and Playing Discs

Before you load a disc, make sure that it is compatible with the player. Insert the disc with the label facing the headliner of the vehicle.

Note:

•

the following Discs

MiniDisc

CANNOT

be used with this player :

•

Laserdisc

•

•

Blu-ray disc (BD)

.

To load and play a disc:

1. Press the Power button to turn the unit ON.

2. Select DVD mode and insert the disc (Label facing headliner) into the disc compartment.

23

TROUBLESHOOTING

PROBLEM

IR remote inoperative

Disc won't play

Play starts, but then stops immediately

No sound or distorted sound

Can’t advance through a movie

SOLUTION

Verify that the batteries in the remote are fresh.

Verify that the remote sensor eye is not obstructed.

Insert a disc with the label side facing up.

Check the type of disc you put into disc tray. This DVD only plays DVDs, audio CDs and MP3s. Blu-ray (BD) discs will not play in this player.

Both the unit and the disc are coded by region. If the regional codes don’t match, the disc can’t be played.

The disc is dirty. Clean it.

Condensation has formed. Allow player to dry out.

Make sure your DVD is connected properly. Make sure all cables are securely inserted into the appropriate jacks.

If you are using the 2-channel IR headphones, make sure you turn on the IR headphone power, make sure the correct channel (A-B) is selected.

Make sure the Modulator is ON and the proper Frequency has been selected.

Make sure that unit is set to M1 when using Single Channel Headphones.

It can’t advance through the opening credits and warning information that appear at the beginning of movies because the disc is programmed to prohibit that action.

24

TROUBLESHOOTING (cont’d)

PROBLEM

Not allowed at the moment

Picture is distorted

No forward or reverse scan

SOLUTION

The feature or action cannot be completed at this time because:

1. The disc’s software restricts it.

2. The disc’s software doesn’t support the feature (e.g., angles)

3. The feature is not available at the moment.

4. You have requested a title or chapter number that is out of range.

The disc might be damaged. Try another disc.

It is normal for some distortion to appear during forward or reverse scan.

Some discs have sections that prohibit rapid scanning or title and chapter skip.

If you try to skip through the warning information and credits at the beginning of a movie, you won’t be able to. This part of the movie is often programmed to prohibit skipping through it.

Technical Support 1-800-645-4994

25

REPLACEMENT PARTS

Remote Control

Wireless Headphones

136-4840

IR1CFF

26

SPECIFICATIONS

LCD Backlighting

Resolution

Pixels

Operation Temperature

Storage Temperature

Backlight

Backlight Life

Video Display System

LED

800 (RGB) x 480

1,152,000

32 ~131 F (0 ~ 55º C)

-4 ~ 158 F (-20 ~ 70º C)

LED

20,000 Hours

NTSC / PAL

Headphone Audio Output 0.03W @ 32 ohms

Video Output 1.0Vp-p @ 75 ohms

Power Source

Dimension

12V DC

L x W x H

14.0" x 12.0" x 2.0"

356mm x 305mm x 51mm

© 2014 VOXX ELECTRONICS CORP., 150 Marcus Blvd. Hauppauge, NY 11788

128-8512F