Casio XW-P1 User`s guide

E
XW-P1
USER’S GUIDE
Please keep all information for future reference.
Safety Precautions
Before trying to use the instrument, be sure to read the
separate “Safety Precautions”.
XWP1-E-1B
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Declaration of Conformity
Model Number: XW-P1
Trade Name: CASIO COMPUTER CO., LTD.
Responsible party: CASIO AMERICA, INC.
Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801
Telephone number: 973-361-5400
This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Important!
Please note the following important information before using this product.
• Before using the optional AC Adaptor to power the unit, be sure to check the AC Adaptor for any damage first. Carefully check
the power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC adaptor that is
seriously damaged.
• Never attempt to recharge batteries.
• Do not use rechargeable batteries.
• Never mix old batteries with new ones.
• Use recommended batteries or equivalent types.
• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated near the battery compartment.
• Replace batteries as soon as possible after any sign they are getting weak.
• Do not short-circuit the battery terminals.
• The product is not intended for children under 3 years.
• Use only a CASIO AD-E95100L adaptor.
• The AC adaptor is not a toy.
• Be sure to disconnect the AC adaptor before cleaning the product.
This mark applies in EU countries only.
Manufacturer:
CASIO COMPUTER CO., LTD.
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Responsible within the European Union:
CASIO EUROPE GmbH
Casio-Platz 1, 22848 Norderstedt, Germany
● Any reproduction of the contents of this manual, either in part or its entirety, is prohibited. Except for your own, personal
use, any other use of the contents of this manual without the consent of CASIO is prohibited under copyright laws.
● IN NO EVENT SHALL CASIO BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION) ARISING OUT OF THE
USE OF OR INABILITY TO USE THIS MANUAL OR PRODUCT, EVEN IF CASIO HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
● The contents of this manual are subject to change without notice.
● The actual appearance of the product may be different from that shown in the illustrations in this User’s Guide.
● Company and product names used in this manual may be registered trademarks of others.
E-1
Contents
General Guide ............................. E-5
Controlling Sounds .................................. E-35
Using a Pedal ....................................................... E-35
Getting Ready to Play ................ E-8
Using the Wheels (Bender, Modulation) ............... E-35
Using the Assignable Knobs ................................. E-35
Connections ...............................................E-8
Using Sliders......................................................... E-36
Power Supply .............................................E-9
Using the Hold Button ........................................... E-36
Using a Household Power Outlet ............................E-9
Changing the Pitch of Notes in Semitone Steps
(Transpose) or Octave Steps (Octave Shift)......... E-36
Using Batteries ......................................................E-10
Auto Power Off ......................................................E-10
Applying Effects to Notes ........................ E-37
Bundled and Optional Accessories ..........E-10
To configure effect settings................................... E-38
Saving an Edited DSP .......................................... E-39
Learning to Play by Playing
(For Synthesizer Novices) ....... E-11
Playing with Built-in Tones .......................E-11
Creating Tones.........................................E-12
Using the Step Sequencer and
Phrases ....................................................E-14
Sounding Arpeggio Phrases
Automatically ............................ E-40
To use the Arpeggio Function ................. E-40
Editing an Arpeggio ................................. E-41
Clearing Arpeggio Data ........................... E-43
Arpeggio Function .................................................E-14
Step Sequencer ....................................................E-15
Recording and Playing Back
Phrases ...................................... E-44
Using the Performance Function..............E-16
To play back a preset .............................. E-44
Playing a Built-in Demo Song ..................E-17
To change the tempo setting ................................ E-45
Conclusion ...............................................E-17
You can use the phrase selection screen
to select the recommended tone for the currently
selected phrase as your Zone Part 1 tone. ........... E-45
Phrase Sequencer ................................................E-14
Selecting and
Creating Tones ......................... E-18
To start phrase playback by
pressing keyboard key (Key Play) ........... E-45
Overview ..................................................E-18
Recording a New Phrase ........................ E-46
To select a tone........................................E-20
To edit and save a tone as a user tone....E-21
Editable Solo Synthesizer Tone Parameters ........E-22
Editable Hex Layer Tone Parameters ...................E-30
Editable Drawbar Organ Tone Parameters ...........E-32
Editable PCM Melody Tone
(Non-drum PCM Tones) Parameters ....................E-33
Editable Drum PCM Tone Parameters..................E-34
E-2
Phrase Data Settings ............................................ E-47
Recording Over Another Phrase
(Overdubbing) ......................................... E-47
Indicators Next to Phrase Numbers......... E-48
To save a phrase..................................... E-48
Contents
Using the Step Sequencer ....... E-49
Other Useful Functions ............ E-67
How the Step Sequencer is organized.....E-49
Using the Mixer ....................................... E-67
Playing Back a Step Sequence................E-51
Instant Adjustment of Settings using
the Sliders and Step Buttons ................................ E-67
Editing a Sequence -Simple Editing.........E-51
Mixer Settings ....................................................... E-68
To turn a step on or off ..........................................E-52
To configure tied note settings ..............................E-52
Global Synthesizer Settings .................... E-69
Tuning (Fine tuning of note pitch) ......................... E-69
Using the Sliders to Change Note and
Velocity Settings....................................................E-52
Local Control......................................................... E-69
Using the Master Slider to Change Note and
Velocity Settings....................................................E-53
Master Coarse Tune
(Tuning of note pitch in semitone steps) ............... E-69
Changing Slider Assignments ...............................E-53
Changing the Function Assigned
to the Master Slider ...............................................E-53
Inputting Step Data by Playing
on the Keyboard, etc. ............................................ E-54
Changing the Solo1 Channel ................................E-54
Changing the Timing of Pattern Switching ............E-55
Syncing Step Sequencer Playback
with an Arpeggio ...................................................E-55
Changing the Step Sequencer Tone........E-55
To sound a single part (solo mode)..........E-55
Editing a Sequence - Advanced...............E-55
Initial Power On Mode .......................................... E-69
Display Contrast ................................................... E-69
Auto Power Off On/Off .......................................... E-69
Using MIDI............................................... E-69
What is MIDI? ....................................................... E-69
MIDI Settings ........................................................ E-70
Deleting Data Saved
on the Synthesizer................................... E-71
Initializing Synthesizer Global
Settings and Data .................................... E-71
Playing a Demo Tune or
a File from a Memory Card...................... E-72
To perform advanced parameter editing ...............E-55
Changing Slider Settings..........................E-59
To copy slider settings from another slider............E-59
Using a Memory Card ............... E-73
Supported Data Types .......................................... E-73
To save an edited sequence ....................E-60
Card and Card Slot Precautions ........................... E-74
Chaining ...................................................E-60
To create a chain ..................................................E-60
Loading and Removing
a Memory Card........................................ E-74
To play back a chain ............................................. E-61
Formatting a Memory Card...................... E-75
To initialize chain settings .....................................E-61
To save a chain in SMF format
to a memory card ..................................................E-61
Saving Synthesizer Data
to a Memory Card.................................... E-75
To save Synthesizer data to a memory card ........ E-75
Using the Performance
Mode .......................................... E-62
Overview ..................................................E-62
Registering and Recalling
Performances...........................................E-62
To register a performance .....................................E-62
To recall a performance ........................................E-63
Editable Performance Parameter List ......E-64
To batch save all Synthesizer data
to a memory card .................................................. E-76
Loading Data from a Memory Card ......... E-77
To load data to Synthesizer memory
from a memory card.............................................. E-77
To batch load all Synthesizer memory data
from a memory card.............................................. E-77
To delete a file from a memory card........ E-78
To rename a file on a memory card......... E-78
Playing a Music File
from a Memory Card ............................... E-78
E-3
Contents
Connecting to a Computer ...... E-79
Minimum Computer System
Requirements...........................................E-79
Connecting the Synthesizer to Your Computer .....E-79
Saving and Loading Synthesizer Data
to a Computer and Editing Synthesizer
Data on a Computer.................................E-80
Reference .................................. E-81
Error Messages........................................E-81
Troubleshooting .......................................E-82
Specifications ...........................................E-84
Operating Precautions .............................E-86
DSP Effect List .........................................E-87
DSP Type List .......................................................E-87
DSP Parameter List ..............................................E-88
Supported Input Characters .....................E-91
MIDI Implementation Chart
E-4
General Guide
• In this manual, buttons, knobs, terminals, and other parts are referred to using a combination of group numbers
( ,
, etc.) and part names.
12
Back
Left
Center
Right
Tray
• The tray is angled slightly.
Take care so items placed
on it do not slide off.
• Do not place cups or any
other liquid containers on
the tray.
Lower left
Left
3
1
4
2
5
(Sliders)
1 through 5 are laid out to facilitate adjustment of a sound as you listen to it.
1 Use these buttons to select the functions assigned to the sliders (5) and 2 buttons. ☞ Page E-35
2 Use these buttons to change the effects assigned to drawbar organ tones, and the parts assigned to the sliders (5).
Groups
3
4
5
☞ Page E-32
Use these knobs to adjust attack, decay, and other sound parameters. ☞ Page E-35
Use these buttons with the step sequencer to turn each step or part on or off. ☞ Page E-52
Use these sliders to control drawbar organ tones. They are also used for editing with the step sequencer and mixer.
☞ Page E-35, E-52, E-67
E-5
General Guide
Center
6
9
7
bk
8
LCD
Indicates name of function
when button is held down.
bm
bn
bo
(Dial)
bl
6 Use the [POWER] button to turn power on or off, and the [VOLUME] knob to adjust the volume level. ☞ Page E-9
7 Use the top three buttons to select the Synthesizer’s mode. Use the bottom three buttons to edit and save tone and other
data, and to configure system-wide general settings. ☞ Page E-11, E-12, E-69
8 Use these buttons to adjust the tempo of the step sequencer, phrase, and other playback. ☞ Page E-45
9 Use these buttons to select a part for editing with the step sequencer or mixer. ☞ Page E-51, E-67
bk Use these buttons to select a step for step sequencer playback or editing. ☞ Page E-51
bl Use these buttons to select a tone category or step sequencer pattern. ☞ Page E-11, E-51
bm Use these buttons to turn the arpeggiator and hold functions on or off, and to change mixer or effect settings.
☞ Page E-38, E-40, E-67
bn Use these buttons to perform phrase sequencer recording and playback. ☞ Page E-44
bo Use the dial for quick change of the numbers and values that appear on the display. ☞ Page E-12
E-6
General Guide
Right
bp
bq
br
bp Use these buttons to select a tone number, performance number, etc. ☞ Page E-20
bq Use the six buttons on the right to move the cursor on the screen, and the minus (–) and plus (+) buttons to change a
displayed value. Press the [MENU] button to display a menu of options for the operation you are currently performing.
☞ Page E-21
br Use these keys for one-touch alteration of the pitch of a sound. ☞ Page E-36
Lower left
bs
bs Use [BENDER] to bend notes and [MODULATION] to add vibrato to notes. ☞ Page E-35
Back
See the next page.
E-7
Getting Ready to Play
Connections
• Whenever you connect any device to the Synthesizer, be sure to read the user documentation that comes with the device.
• This Synthesizer does not have built-in speakers. It will no produce unless you connect some device for sound output.
bt Back left
Memory card (page E-73)
Computer (page E-79)
Other electronic music instrument (page E-69)
ck Back right
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Configuration
and type
depends on your
geographic
location.
*1
Pedal
Other electronic music
instrument
*3
*1
*1
Microphone
CD player, audio player,
etc.
E-8
*1
Audio device, amplifier, etc.
*2
Headphones
Household
power outlet
*1 Standard plug (monaural)
*2 Stereo standard plug
*3 Stereo mini plug
Getting Ready to Play
To do this:
Do this:
(1)
Use a pedal
Connect an optionally available sustain pedal. For information about the type of
effect applied when the pedal is depressed, see page E-65.
(2)
Input sound from another electronic
musical instrument
Use a commercially available connecting cord to connect the output terminal
(monaural) of the other instrument to the Synthesizer.*4
• You can also apply effects to input sounds (page E-67) and use input sounds
when creating new tones as part of the Synthesizer’s tones (page E-22).
(3)
Input from an external device
Use a commercially available connecting cord to connect the output terminal
(stereo) of a CD player or portable audio player to the Synthesizer.*4
(4)
Input external sound using a
microphone
Connect a commercially available dynamic microphone to the Synthesizer.*4
You can use
MIC VOLUME to adjust sound input with the microphone
independently of other sound.
• For information about applying effects to sound input with a microphone, see
page E-67. For information about using input sounds for tone creation, see
page E-22.
ck
(5)
Output Synthesizer sound using audio Use a commercially available connecting cord to connect the input terminal
equipment or an amplifier
(AUX IN, etc.) of the audio equipment or amplifier to the Synthesizer.*4
• For monaural output with a single connecting cord, connect the cord to the
L/MONO terminal of the Synthesizer.
(6)
Use headphones
Connect optional or commercially available headphones to the Synthesizer.*4
• Do not listen to music at very loud volumes for long periods. Doing so creates
the risk of hearing damage.
(7)
Supply power to the Synthesizer
See “Power Supply” below.
*4 Before connecting, be sure to turn off power to the Synthesizer and the device being connected, and turn
to a low level.
Power Supply
Prepare a household power outlet or batteries.
6 VOLUME down
1. Use the AC adaptor specified for this
Synthesizer to connect it to a household power
outlet.
Household power outlet
• Be sure to comply with the separate “Safety
Precautions”. Incorrect use of this product creates the
risk of electric shock and fire.
• Always make sure that the product is turned off before
plugging in or unplugging the AC adaptor, or before
loading or removing batteries.
AC adaptor
• Configuration and type
depends on your
geographic location.
DC 9.5V
Using a Household Power Outlet
Make sure that you use only the AC adaptor (JEITA Standard,
with unified polarity plug) specified for this product. Use of a
different type of AC adaptor can cause malfunction.
2. Press 6 POWER to turn on power.
• To turn off power, press
6 POWER again.
6
Specified AC Adaptor: AD-E95100L
E-9
Getting Ready to Play
■ Low Battery Indication
6
• If you press
POWER only lightly, the display will
light up momentarily but power will not turn on. This
does not indicate malfunction. Press
POWER firmly
and completely to turn on power.
• The AC adaptor will become warm to the touch after
very long use. This is normal and does not indicate
malfunction.
• To prevent breaking of the wire, take care to avoid
putting any type of load on the power cord.
6
No bending!
The following shows the approximate battery life.
Approximately 35 hours* (alkaline batteries, using the
optional CASIO CP-16 headphones)
* Using a high volume setting, playing in very low
temperatures, and certain other playing conditions can
shorten battery life.
Low battery power is indicated when the message “Battery
Low” appears and the indicators shown below flash on the
display. Replace the batteries with new ones.
No winding!
• Never insert metal, pencils, or any other objects into
the product’s 9.5V DC terminal. Doing so creates the
risk of accident.
Using Batteries
You can use six D-size batteries for power.
• Use alkaline or zinc-carbon batteries.
Never use oxyride or any other nickel based batteries.
1. Open the battery cover on the bottom of the
Synthesizer.
Low battery indication (flashing)
Auto Power Off
The Synthesizer turns off automatically to avoid wasting
power if no operation is performed for a preset amount of
time. The Auto Power Off trigger time is six minutes under
battery power and four hours under AC adaptor power.
• You can disable Auto Power Off by turning off the “Auto
Power Off” setting as described under “Global Synthesizer
Settings” (page E-69).
Bundled and Optional
Accessories
2. Load six D-size batteries into the battery
Use of unauthorized accessories creates the risk of fire,
electric shock, and personal injury.
compartment.
• Make sure the positive + and negative - ends of the
batteries are facing as shown in the illustration.
3. Insert the tabs of the battery cover into the
holes on the side of the battery compartment,
and close the cover.
Tabs
4. Press 6 POWER to turn on power.
E-10
• You can get information about accessories that are sold
separately for this product from the CASIO catalog
available from your retailer, and from the CASIO website at
the following URL.
http://world.casio.com/
Learning to Play by Playing (For Synthesizer Novices)
This chapter gets you started with basic operations by actually
using the Synthesizer, while avoiding getting too bogged
down in theory and technical details. It is the perfect place to
start for those who are using a synthesizer for the first time.
■ Three Synthesizer Modes
Performance Mode
Use this mode for playing and
performing. It enables high-level
performance with tone categories,
a Step Sequencer, and more.
Tone Mode
Use this mode for tone creation.
You can select a single tone and
edit it the way you want.
Step Sequencer Mode
This mode is for creating step
sequencer data (sets).
So, let’s get started!
Playing with Built-in Tones
Press 6 POWER to turn on power. The Synthesizer initially
enters its Performance Mode.
Here, lets select a tone hear what it sounds like.
6
Tones are divided among eight categories. Use the
buttons to select the category you want.
bl
bl
Performance Mode
1
2
3
4
5
6
Category
Number
The Performance Mode is great for tapping to the full power of
the Synthesizer during performances, but it is a bit too
advanced for our basic explanation here. For now, let’s start
out with some basic operations in the Tone Mode.
Press
7 TONE to enter the Tone Mode.
7
Step Sequencer Mode
8
Category
number
Overview
Name
1
Solo Synthesizer
Traditional analog
synthesizer tones
2
Hex Layer
Layering of up to six tones
for ensemble sounds with
plenty of depth
3
Drawbar Organ
Traditional drawbar organ
tones
Tone Mode
Performance Mode
7
4 to 8
PCM
Piano to
Various
These tones let you use
sampled sounds to
reproduce the sounds from a
variety of different
instruments.
• For more information, see page E-20.
Lit
Tone Mode
E-11
Learning to Play by Playing (For Synthesizer Novices)
First, let’s see what a Solo Synthesizer tone sounds like.
Press
SOLO SYNTH so the button becomes lit.
bl
The tones of this Synthesizer are divided into 10-tone groups
called “banks”. There are a total of 10 Solo Synthesizer tone
banks numbered 0 through 9, with 10 tones in each bank for a
total of 100 Solo Synthesizer tones.
You can quickly select a bank and a tone number by rotating
the
dial.
Or you can use the
buttons to input specific bank and
tone numbers (page E-20).
bo
Lit
Play something on the keyboard to hear what the tone sounds
like. Use
VOLUME to adjust the volume.
• Note that the Solo Synthesizer tones are monophonic. If
you press multiple keys, only the note of the first key will
sound.
6
bp
You can use the same operations to select the tones in the
other categories besides Solo Synthesizer, so experiment for
yourself to find out what tones are available.
Creating Tones
Tone creation is actually what using a synthesizer is all about.
Starting from a preset tone, you can change various
parameters to create a tone that is your own original sound.
7
With this setting, pressing the
EDIT button provides you
with a collection of powerful editing capabilities (page E-21).
In addition, you also can use the
sliders to easily alter
tones without using the
EDIT button. Here we will take a
simplified look at editing a Hex Layer tone. This process is
covered in greater detail later in this manual.
7
Solo Synthesizer actually is a category that contains 100
built-in (preset*) tones. What we played here is just one of
them. Now let’s play some more of the preset tones in this
category.
* There are also “user tones” which are those that you create
and store for later recall. The terms “preset” and “user” are
also used for other types of data, such as Step Sequencer
data, performance data, etc.
bq
Press the
plus (+) button. Each press increases the
preset tone number and changes the tone setting.
bq
Back
Forward
Tone number
Bank
Tone name
P: Preset
U: User
Category name (abbreviation)
E-12
Press
tone.
5
bl HEX LAYER and select the 0-0 preset Hex Layer
Learning to Play by Playing (For Synthesizer Novices)
Play some notes on the keyboard, and as you do move the
sliders around. This will change the volume settings of
the tones that make up the six layers. Adjust the volume
levels until you get the balance you want.
5
Layer 1 through 6
individual volume
Global
volume
bq
left (U) and right (I) buttons to move the cursor
Use the
between input positions, and the
tone number buttons to
input characters.
• The illustration below shows the letters that each of the
tone number buttons inputs. Each press of a button
cycles through the letters or toggles between the settings
assigned to it. For information about what types of
characters are supported, see page E-91.
bp
bp
Symbols (Part 1)
Numerals
ABC
DEF
GHI
JKL
PQRS
TUV
WXYZ
5
MNO
(Upper/lower case toggle)
After you are finished, you can save the result as a user tone.
7
Press
WRITE to enter the save mode. The save
destination will appear on the display screen.
Save destination
U: User number
0-0: Bank 0, Tone Number 0
Symbols (Part 2)
bq
• You also can use the
minus (–) and plus (+) buttons
or the
dial to scroll through characters.
bo
bq
ENTER.
After the tone name is the way you want, press
This will cause “Replace?” (Do you want to replace the current
tone?) to appear on the display.*1
Press
YES to save the user tone.*2
*1 Saving data to a tone number deletes any data that was
previously assigned to that number.
*2 If you do not want to save the data, press
NO instead
of YES.
bq
bq
bo
bq
dial or
minus (–) and plus (+) buttons to
Use the
specify the bank and tone number where you want to save
your user tone.
bq
To recall a stored user tone, use the same procedure as that
for recalling preset tones. Let’s try recalling the tone we just
saved.
• Before specifying the tone bank and number, press
PRESET/USER to enter the user tone select mode.
bp
bp
Lit (Indicates user tone selected.)
Next, press the
down (w) button to change to the tone
name input screen.
Example:
User tone
Cursor: Input position
E-13
Learning to Play by Playing (For Synthesizer Novices)
At this point you have mastered the simplest steps required to
edit and save tones. But you shouldn’t stop here. Your
Synthesizer has a wealth of other tone editing features,
functions, and tools. Take the time to learn about these and
you will become capable of high-level tone editing. Find out
more under “Selecting and Creating Tones” on page E-18.
Phrase Sequencer
To give you an idea about what a musical phrase is, let’s
listen to a preset phrase.
bn
Hold down
KEY PLAY until the screen shown below
appears on the display.
Phrase Sequencer Mode
Using the Step Sequencer and
Phrases
Bank-Phrase number
Preset
Your sequencer does much more than create tones. It is also
equipped with a collection of functions that support uniquely
expressive rhythms and phrases that enhance your
performances. This section provides a simple introduction to
some of these functions.
Phrase name
Arpeggio Function
Press
bm
bn
Press
PLAY/STOP. This will start playback of one of the
Synthesizer’s built-in preset phrases. Now you perform the
same procedure as you did when selecting a preset tone to
select another preset phrase and play it back.
bm ARPEGGIO so the button becomes lit.
Lit
bn
Instead of using
PLAY/STOP, you can also start playback
of a phrase by pressing a key on the keyboard. Let’s see how
this works.
Press any key on the keyboard. The arpeggio function will
cause the note assigned to the key to play in an endless loop.
The loop will stop when you release the keyboard key.
Pressing two or three keyboard keys will loop play the notes
of the keys you press. Pressing three or more keys will cause
an arpeggio (sometimes referred to as a “broken chord”) to be
played.
There are a variety of different built-in arpeggio types. You
can select one the same way as you select a preset tone, edit
it, and then save it as a user arpeggio type. Let’s go over the
procedure for selecting a preset arpeggio type. Hold down
ARPEGGIO until the screen shown below appears on the
display.
bm
Screen title (arpeggio type)
Bank-Type number
Preset
Now perform the same procedure as you did when selecting a
preset tone to select a preset type and then play it.
For details about arpeggios, see “Sounding Arpeggio Phrases
Automatically” on page E-40.
E-14
First, press
bn
bn KEY PLAY so the button becomes lit.
Lit
This is Key Play Mode. Pressing a keyboard key while in the
Key Play Mode will automatically start playback of a phrase.
Pressing another key will play the phrase using a different
pitch. In the Key Play Mode, the keyboard can be used to
sequentially play a phrase at different pitches to create an
interesting effect.
The Phrase Sequencer main chapter covers information
about how you can record your own phrases and play them
back when you want to. For more information see “Recording
a New Phrase” on page E-46.
Learning to Play by Playing (For Synthesizer Novices)
Step Sequencer
Let’s start out our explanation of the Step Sequencer by
listening to some preset sequence data.
Press
7 STEP SEQ to enter the Step Sequencer Mode.
The Step Sequencer uses nine (8 through 16) of the 16 parts
of the Synthesizer’s sound source, which provides plenty of
support every for very complex rhythms. You can find out
which parts are outputting sound at any time by checking the
level meter on the Synthesizer’s display.
Parts 11 and 14 unused
7
Lit
Step Sequencer Mode
Bank-Sequence number
Preset
4
As the sequence plays back, the
buttons (1 to 16)
continually turn on and off, which indicates the movement of
the notes of the part that is being edited (the part indicated by
the pointer (e) in the illustration above. This is the way the
Step Sequencer repeatedly produces the 16 steps.
You can select a part for editing using the
PART minus
(–) and plus (+) buttons. Use the
slider to edit individual
steps. For more information, see page E-49.
5
Sequence name
bo
dial
As you do when selecting a tone, you can use the
and
number buttons and
minus (–) and plus (+)
buttons to select the sequence you want. For now, lets select
preset sequence 2-3, and then press
START/STOP. This
will start playback of the sequence you selected.
bp
Part selected for editing
bq
bk
9
What we have seen here is just a very small part of the many
and varied rhythms that can be produced by your Synthesizer.
Be sure to take a look at the procedure under “Using the Step
Sequencer” on page E-49 to find out how you can create your
own original sequences.
bk
Each sequence has eight variations (patterns), which you can
select using the
PATTERN 1 to 8 buttons. Experiment
with selecting the various patterns to get an idea of what is
available.
bl
Example: To select Pattern 3
bl
Unlit: Selected pattern
E-15
Learning to Play by Playing (For Synthesizer Novices)
Using the Performance Function
If you have read all of the information in this introductory part
of the manual, you are finally ready to start using the
Performance function. In the Tone Mode, you saw how you
can select a single tone and play it on the keyboard. In the
Performance Mode, you can perform with up to four tones
simultaneously. You also can use the Performance Mode to
register tone, Step Sequencer, and other settings as setup
called a “Performance”. A Performance can be recalled at any
time, even while you are playing, to instantly change the
sequencer’s setup.
Press
bl
Always configure Zone Part 1 first. Press
PCM PIANO to
enter the Quick Tone Mode, which you can use for simple
Performance editing.
bl
Quick Tone Mode
Zone part tone being edited
7 PERFORM to enter the Performance Mode.
7
Lit
Performance Mode
Bank-Performance number
Zone part being edited
Preset
If the pointer (e) on the display is not under 1, use the
PART minus (–) and plus (+) buttons to move it to 1.
After ensuring that the pointer (e) is located at 1, use
to select the tone for Zone Part 1.
9
bl bo
bp bq
9
Performance name
The Performance Mode keyboard uses the four tones
selected as Zone Part 1 through 4. For more information
about zone parts and their tones, see “Selecting and Creating
Tones” on page E-18.
• As shown in the illustration below, the tones of the three
categories on the left can be assigned to Zone Part 1 only.
bl
Can be assigned to
Zone Part 1 only
PART minus (–) and plus (+) buttons to
Next, use the
move the display pointer (e) to 2 and then use the same
procedure as above to select a tone for Zone Part 2. Repeat
the above step for Zone Parts 3 and 4.
bq
After selecting tones for each of the zone parts,
EXIT to
return to the Performance Mode screen. Next, play something
on the keyboard to see what it sounds like. All four of the
tones that you selected above should sound.
Edits pending indicator
Can be assigned to
Zone Parts 1 through 4
The exclamation point ( ! ) indicator on the display indicates
that there are pending edits that have not been saved yet.
Press
WRITE to enter the save mode. Next, perform the
same procedure that you used when saving a user tone to
save your user Performance data.
7
E-16
Learning to Play by Playing (For Synthesizer Novices)
Example: To save the performance to User Bank 2,
Performance 1
Edits saved indicator
Playing a Built-in Demo Song
Use the procedure below to play a built-in demo song that
shows off the full versatility of the Synthesizer.
Press
7 SETTING and 7 WRITE at the same time.
7
Name indicating “Aura Lee” performance data
bq
bq
• The edits pending indicator ( ! ) and edits saved indicator
( * ) are also used in other modes where data is edited and
saved (tones, Step Sequencer, etc.)
When you want to perform the song “Aura Lee”, simply recall
User Performance 2-1 to instantly configure the Synthesizer
with the four tones you registered above. Try recalling a
different Performance number and then recall User
Performance 2-1.
In addition to keyboard tones, you also can register a variety
of other settings as Performance data. An effective way to use
banks would be as song-specific banks. For example, Bank 2
for “Aura Lee”, Bank 3 for another song, etc. For more
information, see “Using the Performance Mode” on page
E-62.
Next, press
ENTER. This will start demo tune play.
• Use the
minus (–) and plus (+) buttons to select a
different tune, and
START/STOP to stop demo tune
play. For more information, see page E-72.
bk
Conclusion
Tone number and other settings you configure on the
Synthesizer are retained even when you turn power off. For
information about returning the Synthesizer to the initial
factory default settings that are in effect when you purchase it,
see “Initializing Synthesizer Global Settings and Data” on
E-71.
This completes the section for synthesizer novices. See the
other sections of this manual for detailed information about
the topics covered briefly in this section. Take your time and
don’t rush, making sure you fully understand as you go along.
If you have problems with any of the terms used in this
manual, you can find more information by searching on the
Web or by consulting a reference book about synthesizers or
electronic music.
Soon you will be well on your way enjoying
the full potential of sound creation!
E-17
Selecting and Creating Tones
7
3
bm bn bo
bp
bq
br
5
9
bl
Overview
The tones of this Synthesizer are made up of the 16 parts shown below, plus externally input parts. This chapter explains how to
select, edit, and save tones using Zone Part 1* in the Tone Mode (page E-11).
It also covers the Effect Function that can be used to enhance tones and controllers that can be used to make various changes in
a tone as you play.
Part Number
Part name
Features
Zone Part1*
This is the Synthesizer’s main part. This part is played whenever you play on the
keyboard. You can select the tone assigned to Zone Part 1 and edit the currently
assigned tone.
2 to 4
Zone Parts 2 through 4*
These parts can be played only in the Performance Mode. Compared with Zone Part
1, your ability to assign and edit the tones assigned to these parts are limited (page
E-62).
5 to 7
–
These parts are sounded when MIDI messages are received from an external
source (page E-69).
1
8 to 16
–
Drum 1 to Chord
Step Sequencer Note Parts (page E-40).
External Input
These are tones that are input via the
ck MIC IN, INST IN jacks (page E-67).
* About zones and zone parts
Keyboard, pedal, button, and other operations not only affect the Synthesizers preset tones, they are also sent as MIDI data and
affect any external device (electronic musical instrument or computer) connected to the Synthesizer.
The settings that apply to both internal and external parts are collectively referred to as a “zone” while the parts of the
Synthesizer’s built-in sound source that correspond to a zone is called “zone parts”. For example, if you select a tone with
Synthesizer Zone 2, that tone can be the part that corresponds to both the internal sound source Zone Part 2 or MIDI Channel 2
of an external device.
• You can change the relationships between zones and MIDI channels (page E-64).
E-18
Selecting and Creating Tones
Built-in sound
source
Zone Part 1
Zone 1
settings
Zone Part 2
Zone 2
settings
Zone Part 3
Zone 3
settings
Zone Part 4
Zone 4
settings
External device
(MIDI
Channel 1)
(MIDI
Channel 2)
(MIDI
Channel 3)
(MIDI
Channel 4)
E-19
Selecting and Creating Tones
To select a tone
1. Press 7 TONE.
The button will light and the Synthesizer will enter the Tone Mode.
2. Use the bl SOLO SYNTH to VARIOUS buttons to select a tone category.
3. Press bp PRESET/USER to select preset tones or user tones.
• Preset tones are selected while the button is unlit, while user tones are selected while the button is lit.
4. Press the bp NUM/BANK button so the button is flashing.
• While this button is flashing, the
bp (0 to 9) buttons can be used to input a bank number.
5. Use the bp number buttons (0 to 9) to select a bank number.
bp
• As soon as you input a bank number, the
NUM/BANK light will go out. While this button is unlit, it indicates that the
(0 to 9) buttons can be used to input a tone number.
bp
6. Use the bp number buttons (0 to 9) to input a tone number.
bo
• You also can select a tone number by rotating the
dial.
• One more way to change the tone number is to use the
minus (–) and plus (+) buttons to decrease or increase the
displayed number. Pressing the
minus (–) and plus (+) buttons at the same time will jump to the first tone in the current
selected category (see next section).
bq
bq
■ Tone Category Overview
Category
Number
Name
Number of Tones
Description
Preset
User
100
100
1
Solo Synthesizer
This category contains traditional analog synthesizer tones. You
can select a waveform as a base, and then edit the three
elements of a sound (pitch, tone, volume) to create exactly the
sound you want. Monophonic.
2
Hex Layer
In this category, up to six tones are layered for ensemble sounds
with plenty of depth. Each of the layered sounds can be edited
individually.
50
50
3
Drawbar Organ
This category includes traditional drawbar organ tones with nine
drawbars and rotary speakers. The Synthesizer’s
sliders
operate as drawbars with these tones.
50
50
420
110
4
Piano
5
6
Strings/Brass
PCM
Guitar/Bass
7
Synthesizer
8
Various
5
The tones in this category let you use sampled sounds to
reproduce the sounds from a variety of different instruments.
• See the separate “Appendix” for a complete list of tones.
• Under initial factory default settings, the user tone numbers are assigned the same tones as the corresponding preset tone
numbers.
E-20
Selecting and Creating Tones
To edit and save a tone as a user
tone
Enters a group.
Exits a group.
bo
1. Select the tone you want to edit.
bq
Selects item.
• You can select a preset tone or an existing user tone
for editing.
2. Press 7 EDIT.
This will display the top screen of the tone editing list.
Example: First page of the Solo Synthesizer tone editing
list
Changes setting.
Scrolls pages.
List title
4. After you finish with your edits, press 7 EDIT.
This exits the tone editing list.
• The edits pending indicator ( ! ) on the display indicates
that there are pending edits that have not been saved
yet. Your edits will be lost if you change to another
operation without saving them. Advance to step 5
below if you want to save your edits.
Edits pending indicator
List
3. Use bq to select the item you want and change
the selected setting.
bo
• You also can change setting by rotating the
dial.
• For details about the displayed contents, see the
information presented for each tone category in the
sections of this manual from “Editable Solo Synthesizer
Tone Parameters” (page E-22) to “Editable Drum PCM
Tone Parameters” (page E-34).
Example: To select the “Volume” item on the top screen
and change its setting to 055
The options on this screen are groups, which are
made up of multiple items. Selecting a group and
pressing
ENTER will enter the group.
bq
Page
5. Press 7 WRITE and then save your edited tone
as a user tone.
• For information about how to delete user tones, see
page E-71.
• The settings of some of the items on the tone editing list
can be changed using the Synthesizer’s sliders, without
going through the tone editing list. See “Controlling
Sounds” in the next section.
■ Saving User Tones to an External Device
• Memory card (page E-73)
• Computer (page E-79)
Item selection Cursor
Setting
E-21
Selecting and Creating Tones
Editable Solo Synthesizer Tone Parameters
Solo Synthesizer tones are synthesized by combining tones of the six blocks, number (1) through (6), in the illustration below.
Before actually getting into tone editing, you should spend a little time becoming familiar with the structure and the details of each
block.
■ Solo Synthesizer Tone Configuration Diagram
(2) Synth OSC2 Block
(9) LFO2 Block
(8) LFO1 Block
(1) Synth OSC1 Block
EG*
EG*
EG*
EG*
Synth OSC
Filter
Amp
LFO
To blocks (1) through (7)
(4) PCM OSC2 Block
(3) PCM OSC1 Block
EG*
EG*
EG*
(7) Total Block
EG*
PCM OSC
Filter
Amp
Filter
Solo
Synthesizer
DSP
(5) External Input Sound Block
EG*
EG*
EG*
To blocks (1) through (9)
MIC IN
Pitch shifter
Filter
Amp
(10) Controllers
•
•
•
•
•
•
INST IN
(6) Noise Block
Noise
generator
* Envelope Generator
E-22
EG*
EG*
Filter
Amp
Keyboard
Pedal
HOLD
Bender
Modulation
MIDI receive messages
bm
(Virtual controllers)
Output
Selecting and Creating Tones
Description
(1) Synthesizer OSC1 Block
“OSC” is an abbreviation of “oscillator”, which is where a sound is actually produced. These two
synth OSC blocks creates sound using a sine wave, sawtooth wave, or other base waveform,
just like an analog synthesizer.
• Synth OSC: Generates the base sound and determines the pitch.
• Filter: Cuts some of the frequencies to adjust timbre.
• Amp: Adjusts volume.
• Three EG (envelope generators):
Control changes in pitch, timbre, volume, and other parameters over time.
The nearby illustration shows an example of a volume envelope.
Volume
(2) Synthesizer OSC2 Block
Time
Attack
Sustain
Decay
(3) PCM OSC1 Block
(4) PCM OSC2 Block
Release 2
Release 1
This block creates sound based on PCM sounds (same sound quality as sounds in the PCM
Tone category). For information about show the editable parameters of this block differ from
those for the OSC blocks above, see “Editable Parameters of Blocks (1) through (6)” (page
E-24).
(5) External Input Sound Block
Instead of an oscillator, this block creates sound based on sound input through the
Synthesizer’s
MIC IN and INST IN jacks. The pitch change range of sound produced by
this block is limited.
(6) Noise Block
Instead of an oscillator, this block creates sound based on noise generated by a special noise
generator. The pitch of sound produced by this block cannot be edited.
(7) Total Block
This block combines signals (1) through (6) and sends the completed tone to the filters and
DSP (a type of effect).
(8) LFO1 Block
“LFO” is an abbreviation of “low-frequency oscillator”. The LFOs send waveform information to
each block that is used as the basis for modulation, tremolo and other reverb effects.
(9) LFO2 Block
(10) Controllers
ck
Controllers include the keyboard, bender, and other controllers, as well as MIDI messages.
Control messages are sent to blocks (1) through (9) to control tones.
A virtual controller function can be used to freely configure combinations of controller types
(sources) and the parameters being controlled (destinations) to perform such actions as “pedal
depressed, change volume”.
E-23
Selecting and Creating Tones
■ Editable Parameters of Blocks (1) through (6)
5) and four knobs (3) can be used for quick and easy adjustment of some of the parameters in the list
• The nine sliders (
below (page E-35).
Preparation
Perform the following steps from the screen in step 2 of the procedure under “To edit and save a tone as a user tone” on page
E-21.
1. Select “OSC Block >Ent” and then press bq ENTER to enter the group.
2. Use the 9 PART minus (–) and plus (+) buttons to select the block you want to edit.
Block
Syn1: Synth OSC1
Syn2: Synth OSC2
PCM1: PCM OSC1
PCM2: PCM OSC2
Ext: External input
Noise: Noise
Editable Parameter List
• Shaded cells indicate a group made up of multiple items. Press
ENTER to display the items that make up a group.
• (V) at the end of a display item indicates an item that can be selected as a Block (10) virtual controller destination (page E-29).
bq
Display Text
Description
Settings
OSC On Off
OSC on/off. Selecting off disables the entire block.
Oscillator >Ent (Block (1) to (5) only)
Oscillator. Group of editable parameters associated with the pitch of the synth
OSC, PCM OSC, and pitch shift.
• This group can be entered by performing step 1 under “To edit and save a tone
EDIT.
as a user tone” (page E-21) and then holding down
Off, On
7
Synth Wave
(Blocks (1) and (2) only)
PCM Wave
(Blocks (3) and (4) only)
Synth wave, PCM wave. Selects the base wave for a sound generated by the
synth OSC or PCM OSC.
• A wave whose name is displayed with “L” or “B” next to it will sound at a pitch
that is one octave lower than the actual pitch. In the case of a “B” wave, nothing
will sound when a keyboard key higher than C5 is pressed.
• See the separate “Appendix” for details about wave types.
• This item is not present in Block (5).
See the separate
“Appendix”.
Pitch (V)
Pitch. Adjusts the maximum and minimum pitch values within a range of ±2
octaves. A setting of –256 lowers the pitch two octaves, while a setting of 255
raises the pitch two octaves.
–256 to 0 to +255
Detune. Fine adjustment of the tuning.
–256 to 0 to +255
Detune (V)
Key follow. Adjusts the amount of pitch change between neighboring keyboard
keys. A higher value represents greater change.
Example: When Key Follow Base is keyboard key C4
Key Follow = 127
Key Follow = 64
KeyFollow (V)
–128 to 0 to +127
D4
C#4
C4
Bb4
C4
C#4
Key Follow = 0
Key Follow
Key Follow = -127
Key Follow Base
E-24
KeyFolBase (V)
Key follow base. Keyboard key that is the center of key follow.
• Setting value can be specified using the keyboard keys.
C-1 to G9
Env.Depth (V)
Envelope depth. Specifies how the envelope shown below is applied.
–64 to 0 to +63
B
Selecting and Creating Tones
Display Text
Description
Settings
Pitch envelope. Group of editable envelope (Envelope Generator) parameters
applied to the synth OSC, PCM OSC, and pitch shifter.
• The figure below also applies to filter, amp, and other envelopes. With the pitch
envelope, the pitch of the sound corresponds to the vertical (Level) axis.
Level
AL
RL1
SL
Envelope >Ent
IL
RL2
AT
IL :
AT :
AL :
DT :
SL :
DT
Init Level
Attack Time
Attack Level
Decay Time
Sustain Level
RT1
RT1 :
RL1 :
RT2 :
RL2 :
RT2
Time
Release Time1
Release Level1
Release Time2
Release Level2
Init.Level (V)
Initial level. Pitch of the sound at initial note on.
–64 to 0 to +63
Atk.Time (V)
Attack time. Time it takes until the attack level is reached from the initial level.
0 to 127
Atk.Level (V)
Attack level. Target level reached immediately after note on.
–64 to 0 to +63
Dec.Time (V)
Decay time. Time it takes for the sound to reach the sustain level from the attack
level.
0 to 127
Sus.Level (V)
Sustain level. Level the sound is sustained as long as a key or pedal is
depressed.
–64 to 0 to +63
Rel.Time1 (V)
Release time 1. Time it takes to reach Release Level 1 after a key is released.
0 to 127
Rel.Level1 (V) Release level 1. Target level reached immediately after a key is released.
–64 to 0 to +63
Rel.Time2 (V)
0 to 127
Release time 2. Time it takes to reach Release Level 2 from Release Level 1.
Rel.Level2 (V) Release level 2. Second target level reached after a key is released.
–64 to 0 to +63
Clk.Trig
Clock trigger. Specifies the number of beats for resetting the envelope. Selecting
a setting from 1/4U to 4U resets to the timing of the back beat.
Off, 1/4, 1/3, 1/2, 2/3,
1, 3/2, 2, 3, 4, 1/4U,
1/3U, 1/2U, 2/3U, 1U,
3/2U, 2U, 3U, 4U
Ext.Trig
(Block (5)
only)
External trigger. When on, the envelope is reset by an external trigger.
Off, On
LFO1 Depth (V)
LFO1 depth. Specifies how LFO1 from Block (8) is applied.
–64 to 0 to +63
LFO2 Depth (V)
LFO2 depth. Specifies how LFO2 from Block (9) is applied.
–64 to 0 to +63
PulseWidth
(Blocks (1) and (2) only) (V)
Pulse width. Adjusts the width of the square wave when the synth wave is a
square wave.
0 to 127
PWM LFO1 depth. Adjusts the depth of pulse width modulation by LFO1.
PWM
PWM LFO1 Depth
(Blocks (1) and (2) only) (V)
–64 to 0 to +63
PWM LFO2 Depth
(Blocks (1) and (2) only) (V)
PWM LFO2 depth. Adjusts the depth of pulse width modulation by LFO2.
–64 to 0 to +63
Sync OSC (Block (2) only)
Oscillator sync. Turning on this resets the Block (2) sound wave in accordance
with the Block (1) sound wave period, cause them to become synced.
Off, On
OriginalKey (Block (5) only)(V)
Original key. Selects the keyboard keys where the externally input sound to
Block (5) is sounded as-is at its original pitch.
• Setting can be specified using the keyboard keys.
C-1 to G9
MicInstLvl (Block (5) only) (V)
Mic/inst level. Level of external input sound to Block (5).
0 to 127
E-25
Selecting and Creating Tones
Display Text
Description
Settings
TrigThresh (Block (5) only) (V)
Trigger threshold. Specifies the external input level threshold value that
determines whether or not an external input trigger (page E-25) is applied.
0 to 127
TrigRelease
(Block (5) only) (V)
Trigger release time. Adjusts the time following external input trigger (page E-25)
operation that the next trigger operation is blocked.
0 to 127
P.ShiftMode (Block (5) only)
Pitch shifter mode. A larger setting value lengthens the time until note on, but
increases tone quality. When this setting is off, the same pitch sounds no matter
which keyboard key is pressed.
Off, 1, 2, 3
P.ShiftMix (Block (5) only)
Pitch shifter mix. Specifies the volume ratio between the pitch shifted sound (shift
sound) and the unshifted sound.
0: Shift sound only
7: Both sounds at same volume
15: Original sound only
0 to 15
Noise Type (Block (6) only)
Noise type. Selects the type of noise generated by Block (6). White noise (equal
noise for all frequencies), pink noise (noise inversely proportional to the
frequency) and other types of noise are available.
• See the separate “Appendix” for a complete list of noise types.
See the separate
“Appendix”.
Filter >Ent
Filter. Group of editable parameters associated with the filters (tones) in each
block.
Gain
Gain. Specifies how the volume of frequency components that are higher than
the cut off frequency setting value described below is attenuated. There is no cut
off when “Flat” is specified here.
–18dB, –12dB, –6dB,
–3dB, Flat
Cutoff (V)
Cutoff frequency. Specifies the filter cutoff frequency.
0 to 15
TouchSense (V)
Touch sense. Specifies the degree of change in the filter in accordance with
change in keyboard playing touch.
–64 to 0 to +63
KeyFollow (V)
Key follow. Adjusts the amount of filter change between neighboring keyboard
keys. A higher value represents greater change.
–128 to 0 to +127
KeyFolBase (V)
Key follow base. Keyboard key that is the center of key follow.
• Setting can be specified using the keyboard keys.
C-1 to G9
Env.Depth (V)
Envelope depth. Specifies how the envelope shown below is applied.
–64 to 0 to +63
Envelope >Ent
Filter envelope. Group of editable envelope (Envelope Generator) parameters
applied to filters.
• For details about group items and setting ranges, see “Pitch Envelope”. With
this group, the vertical (Level) axis in the pitch envelope diagram corresponds
to how the filter is applied.
0 to 127 (Initial Level
to Release Level 2)
• The setting ranges
for Clock Trigger
and External Input
Trigger are the
same as those for
Pitch Envelope.
LFO1 Depth (V)
LFO1 depth. Specifies how LFO1 from Block (8) is applied.
–64 to 0 to +63
LFO2 Depth (V)
LFO2 depth. Specifies how LFO2 from Block (9) is applied.
–64 to 0 to +63
Amp >Ent
Amp. Group of editable parameters associated with the amp (volume) in each
block.
Volume (V)
Volume. Specifies the amp volume.
0 to 127
TouchSense (V)
Touch sense. Specifies the degree of change in volume in accordance with
change in keyboard playing touch.
–64 to 0 to +63
KeyFollow (V)
Key follow. Adjusts the amount of volume change between neighboring keyboard
keys. A higher value represents greater change.
–128 to 0 to +127
KeyFolBase (V)
Key follow base. Keyboard key that is the center of key follow.
• Setting can be specified using the keyboard keys.
C-1 to G9
Envelope >Ent
Amp envelope. Group of editable envelope (Envelope Generator) parameters
applied to amps.
• For details about group items, see “Pitch Envelope”. The vertical (Level) axis in
the pitch envelope diagram corresponds to the volume in the case of this
group. However, the setting range for the nine items from Initial Level to
Release Level 2 is 0 to 127, which is different from the pitch envelope items.
0 to 127 (Initial Level
to Release Level 2)
• The setting ranges
for Clock Trigger
and External Input
Trigger are the
same as those for
Pitch Envelope.
LFO1 Depth (V)
LFO1 depth. Specifies how LFO1 from Block (8) is applied.
–64 to 0 to +63
LFO2 Depth (V)
LFO2 depth. Specifies how LFO2 from Block (9) is applied.
–64 to 0 to +63
Legato
Legato. Turning this setting on causes subsequent notes to be played smoothly
and connected.
Off, On
Portamento
Portamento. Turning on this setting applies a portamento effect.
Off, On
E-26
Selecting and Creating Tones
Display Text
PortaTime (V)
Description
Portamento Time. Specifies the time until the next note is reached by
Portamento.
Settings
0 to 127
■ Block (7): Total Block Filter Editable Parameters
Preparation
On the screen that appears in step 2 under “To edit and save a tone as a user tone” (page E-21), select “Total Filter >Ent” and then
press
ENTER to enter the group.
bq
Editable Parameter List
• Shaded cells indicate a group made up of multiple items. Press
ENTER to display the items that make up a group.
• (V) at the end of a display item indicates an item that can be selected as a Block (10) virtual controller destination (page E-29).
bq
Display Text
Description
Settings
FilterType
Filter type. Selects the filter type.
LPF: Low-pass filter. Cuts high-range components above the cut off frequency.
BPF: Band-pass filter. Cuts low-range and high-range components outside of a range centered on
the cut off frequency.
HPF: High-pass filter. Cuts low-range components below the cut off frequency.
Refer to the cell to the
left.
Cutoff (V)
Cutoff frequency. Specifies the cut off frequency of all Solo Synthesizer tones.
0 to 127
Resonance (V)
Resonance. Emphasizes notes in the vicinity of the cut off frequency to alter the tone.
0 to 127
TouchSense (V)
Touch sense. Specifies the degree of change in the filter in accordance with change in keyboard
playing touch.
–64 to 0 to +63
KeyFollow (V)
Key follow. Adjusts the amount of filter change between neighboring keyboard keys. A higher value
represents greater change.
–128 to 0 to +127
KeyFolBase (V)
Key follow base. Keyboard key that is the center of key follow.
• Setting can be specified using the keyboard keys.
C-1 to G9
Env.Retrig
Envelope generator retrigger. Turning on this setting retriggers the filter with each keyboard key
press.
Off, On
Env.Depth (V)
Envelope depth. Specifies how the envelope shown below is applied.
–64 to 0 to +63
Envelope >Ent
Total filter envelope. Group of editable envelope (Envelope Generator) parameters applied to Total
Block filters.
• For details about group items, see “Pitch Envelope”. With this group, the vertical (Level) axis in the
pitch envelope diagram corresponds to how the filter is applied.
0 to 127 (Initial Level to
Release Level 2)
• The setting ranges for
Clock Trigger and
External Input Trigger
are the same as those
for Pitch Envelope.
LFO1 Depth (V)
LFO1 depth. Specifies how LFO1 from Block (8) is applied.
–64 to 0 to +63
LFO2 Depth (V)
LFO2 depth. Specifies how LFO2 from Block (9) is applied.
–64 to 0 to +63
E-27
Selecting and Creating Tones
■ Block (8): LFO1 and Block (9): LFO2 Editable Parameters
Preparation
Perform the following steps from the screen in step 2 of the procedure under “To edit and save a tone as a user tone” on page
E-21.
1. Select “LFO >Ent” and then press bq ENTER to enter the group.
2. Use the 9 PART minus (–) and plus (+) buttons to select the block you want to edit.
Editable Parameter List
• (V) at the end of a display item indicates an item that can be selected as a Block (10) virtual controller destination (page E-29).
Display Text
Description
Settings
Wave type. Specifies one of the following wave types to be used for LFO.
Sin
(Sine Wave)
Puls 1:3
(Square Wave 1:3)
Tri
(Triangular Wave)
Puls 2:2
(Square Wave 2:2)
Saw up
(Sawtooth Wave Up)
Puls 3:1
(Square Wave 3:1)
Saw down
(Sawtooth Wave
Down)
Random
(Random)
WaveType
Refer to the cell to the
left.
Sync
Sync. Specifies what LFO is synced with.
Off: No syncing
Tempo: Synced with beat specified by clock sync (see below).
LFO1 (Can be selected with LFO2 only.): Synced with LFO1.
Refer to the cell to the
left.
Rate (V)
Rate. Specifies the LFO speed (frequency). This setting is enabled when the above Sync setting is
off.
0 to 127
Clk.Sync
Clock sync. Specifies the number of beats synced with the LFO frequency. Selecting a setting from
1/4U to 4U syncs with the timing of the back beat.
• This setting a valid only when the sync setting is “Tempo”.
1/4, 1/3, 1/2, 2/3, 1, 3/2,
2, 3, 4, 1/4U, 1/3U, 1/2U,
2/3U, 1U, 3/2U, 2U, 3U,
4U
Depth (V)
Depth. Specifies how LFO is applied.
0 to 127
Delay (V)
Delay. Specifies the degree of delay in the timing for applying LFO.
0 to 127
Rise (V)
Rise. Specifies the time it takes from the start of application of the LFO until the effect reaches the
level specified by Depth above.
0 to 127
Mod.Depth (V)
Modulation depth. Specifies how modulation is applied to the LFO.
0 to 127
E-28
Selecting and Creating Tones
■ Block (10): Controllers Editable Virtual Controller Parameters
These controllers are virtual controllers for adjusting any editable parameters (destinations) with any input method (source).
Preparation
Perform the following steps from the screen in step 2 of the procedure under “To edit and save a tone as a user tone” on page
E-21.
1. Select “VirtualCtrl >Ent” and then press bq ENTER to enter the group.
• Controllers are numbered 1 through 8, and are assigned to the
5 sliders (1/9 through 8/16).
2. Use the 9 PART minus (–) and plus (+) buttons to select the number of the controller you want to edit.
Editable Parameter List
Display Text
Source
Description
Settings
Source. Specifies the input method.
Off: None
CC00 to CC97: MIDI control change*
NoteOnKeyNum: Key number of MIDI note on message
NoteOnVel: Velocity value of MIDI note on message
Ch.Pressure: MIDI channel after touch
BENDER center
Bend Up: Upward operation from
BENDER center
Bend Down: Downward operation from
MODULATION operation
Modulation:
LFO1: LFO1 (Block (8))
LFO2: LFO2 (Block (9))
bs
bs
Refer to the cell to the
left.
bs
* For details about each setting, refer to the MIDI Implementation document
(http://world.casio.com/) and other MIDI documentation.
Depth
Dest
Depth. Specifies how virtual controller is applied.
–128 to 0 to +127
Destination. Specifies the destination parameter for a virtual controller operation.
• Off
• Block (1) to (9)
parameters (pages
E-24 through E-28)
whose “Display Text”
items have “(V)” after
them.
• DSP parameters (page
E-88)
■ Other Editable Items
This section explains parameters that are not part of the blocks described up to this point. These settings not only apply to the Solo
Synthesizer, but also to other category tones as well.
Preparation
Display the screen in step 2 of the procedure under “To edit and save a tone as a user tone” on page E-21.
Editable Parameter List
• Shaded cells indicate a group made up of multiple items. Press
Display Text
bq ENTER to display the items that make up a group.
Description
Settings
DSP On/Off
(Non-Solo
Synthesizer
tones only)
DSP on/off. Specifies whether or not DSP should be applied to tones.
ENTER enters the DSP editing screen (page E-39).
• When this setting is on, pressing
• This item is not displayed on the Solo Synthesizer tone editing list.
DSP Edit >Ent
DSP edit. Group of editable effect function DSPs (page E-37). Press
DSP editing screen.
Disabled when the above DSP On/Off setting is off.
Volume
Volume. Specifies the main volume.
0 to 127
Rev.Send
Reverb send. Specifies how reverb (page E-37) is applied to a tone.
0 to 127
Cho.Send
(Non-Solo
Synthesizer
tones only)
Chorus send. Specifies how chorus (page E-37) is applied to a tone.
• This item is not displayed on the Solo Synthesizer tone editing list.
0 to 127
bq
Off, On
bq ENTER to advance to the
E-29
Selecting and Creating Tones
Editable Hex Layer Tone Parameters
Hex Layer tones have three types of editable parameters: parameters for each of the individual layers (Layer 1 through Layer 6),
parameters that affect all six of the layers, and the same parameters that apply to the other tone categories.
5) and four knobs (3) can be used for quick and easy adjustment of some of the parameters in the list below (page E-35).
• The nine sliders (
■ Editable Parameters for Individual Layers (Layer 1 through Layer 6)
Preparation
Perform the following steps from the screen in step 2 of the procedure under “To edit and save a tone as a user tone” on page
E-21.
1. Select “Layer Edit >Ent” and then press bq ENTER to enter the group.
• You also can enter the group using the following shortcut: Perform step 1 under “To edit and save a tone as a user tone”
(page E-21) and then hold down
EDIT. This will enter the group.
7
2. Use the 9 PART minus (–) and plus (+) buttons to select the layer number you want to edit.
Layer number
Editable Parameter List
Display Text
Description
Settings
LayerOn/Off
Layer on/off. Selecting off disables layer.
Off, On
PCM Wave
PCM wave. Selects a tone from among the PCM waves.
• See the separate “Appendix” for information about PCM wave types.
See the separate
“Appendix”.
Volume
Volume. Specifies the volume.
–128 to 0 to +127
Pan
Pan. Specifies the stereo position of the sound. 0 indicates the center, while a smaller values shifts
to the left and a larger value shifts to the right.
–64 to 0 to +63
CoarseTune
Coarse tune. Changes the pitch of notes by semitone units.
–24 to 0 to +24
FineTune
Fine tune. Fine tunes the pitch of the sound. Lowers the value up to –256 or raises the value up to
+255 in semitone steps.
–256 to 0 to +255
Cutoff
Cutoff frequency. Specifies the cut off frequency of the layered tone.
–128 to 0 to +127
TouchSense
Touch sense. Specifies the degree of change in volume in accordance with change in keyboard
playing touch.
–128 to 0 to +127
Atk.Time
Attack time. Specifies the time it takes to reach peak value from note on.
–128 to 0 to +127
Dec.Time
Decay time. Specifies the time it takes for the volume to reach the sustain level from the attack level. –128 to 0 to +127
Sus.Level
Sustain level. Specifies the volume at which the sound is sustained as long as a key or pedal is
depressed.
–128 to 0 to +127
Rel.Time
Release time. Specifies the time it takes for a sustained sound to decay after a key is released.
–128 to 0 to +127
Rev.Send
Reverb send. Specifies how reverb (page E-37) is applied to a tone.
–128 to 0 to +127
Cho.Send
Chorus send. Specifies how chorus (page E-37) is applied to a tone.
–128 to 0 to +127
KeyRangeLow
Key range low. Specifies the lower limit of the enabled keyboard range. Nothing sounds when any
keyboard key below this range is pressed.
• Setting can be specified using the keyboard keys.
C-1 to G9
KeyRangeHi
Key range high. Specifies the upper limit of the enabled keyboard range. Nothing sounds when any
keyboard key above this range is pressed.
• Setting can be specified using the keyboard keys.
C-1 to G9
VelRangeLow
Velocity range low. Specifies the minimum value of the effective velocity. Nothing sounds when
velocity less than this setting is played.
0 to 127
VelRangeHi
Velocity range high. Specifies the maximum value of the effective velocity. Nothing sounds when
velocity greater than this setting is played.
0 to 127
Pitch Lock
(Layers 2, 4, and
6 only)
Pitch lock. When this setting is turned on for Layer 2, the Layer 2 pitch is changed to the same pitch
as Layer 1 so both pitches are the same. The same is true for Layers 3 and 4, and Layers 5 and 6.
Off, On
E-30
B
Selecting and Creating Tones
■ Editable Parameters for All Layers (Layer 1 through Layer 6)
Preparation
Display the screen in step 2 of the procedure under “To edit and save a tone as a user tone” on page E-21.
Editable Parameter List
• Shaded cells indicate a group made up of multiple items. Press
Display Text
bq ENTER to display the items that make up a group.
Description
Settings
Detune. Causes the tuning of Layers 1 through 6 to be slightly different from each other. A
larger setting value increases the amount of detuning. The maximum value (31) results in
a difference of 100 cents (semitones) between Layer 1 and Layer 6.
Detune = 31
+50cent
Detune
0 to 31
Layer4 Layer5 Layer6
Detune = 0
Layer1 Layer2 Layer3
−50cent
Pitch LFO >Ent
Pitch LFO. Group of editable LFOs applied to the pitch of a layered tone.
Wave type. Specifies a wave type to be used for LFO. The details of the selectable waves
are the same as those for “WaveType” of “Block (8): LFO1 and Block (9): LFO2 Editable
Parameters” (page E-28).
Sin, Tri, SawUp,
SawDown, Puls1:3,
Puls2:2, Puls3:1
Rate
Rate. Specifies the LFO speed (frequency).
0 to 127
Depth
Depth. Specifies how LFO is applied.
–128 to 0 to +127
Delay
Delay. Specifies the degree of delay in the timing for applying LFO.
0 to 127
Rise
Rise. Specifies the time it takes from the start of application of the LFO until the effect
reaches the level specified by Depth above.
0 to 127
Mod.Depth
Modulation depth. Specifies how modulation is applied to the LFO.
0 to 127
After Depth
After depth. Specifies LFO change when MIDI channel after touch is received.
0 to 127
Amp LFO. Group of editable LFOs applied to the volume of a layered tone. Group items
and setting ranges are the same as “LFO (Pitch LFO)”, above.
Refer to the cell to the
left.
WaveType
Amp LFO >Ent
■ Editable Parameters Common to Other Tone Categories
See “Other Editable Items” on page E-29.
E-31
Selecting and Creating Tones
Editable Drawbar Organ Tone Parameters
There are two types of parameters: drawbar organ tone specific editable parameters and the same parameters that apply to the
other tone categories.
• The nine sliders ( ), three buttons ( ), and four knobs ( ) can be used for quick and easy adjustment of some of the
parameters in the list below (page E-35).
5
2
3
■ Drawbar Organ Specific Editable Parameters
Preparation
Display the screen in step 2 of the procedure under “To edit and save a tone as a user tone” on page E-21.
Editable Parameter List
• Shaded cells indicate a group made up of multiple items. Press
Display Text
bq ENTER to display the items that make up a group.
Description
Settings
Ft16'
16 feet. Specifies the pull out amount of the 16-foot drawbar.
0 to 8
Ft5 1/3'
5 and 1/3 feet. Specifies the pull out amount of the 5 1/3-foot drawbar.
0 to 8
Ft8'
8 feet. Specifies the pull out amount of the 8-foot drawbar.
0 to 8
Ft4'
4 feet. Specifies the pull out amount of the 4-foot drawbar.
0 to 8
Ft2 2/3'
2 and 2/3 feet. Specifies the pull out amount of the 2 2/3-foot drawbar.
0 to 8
Ft2'
2 feet. Specifies the pull out amount of the 2-foot drawbar.
0 to 8
Ft1 3/5'
1 and 3/5 feet. Specifies the pull out amount of the 1 3/5-foot drawbar.
0 to 8
Ft1 1/3'
1 and 1/3 feet. Specifies the pull out amount of the 1 1/3-foot drawbar.
0 to 8
Ft1'
1 foot. Specifies the pull out amount of the 1-foot drawbar.
0 to 8
Perc.2nd
2nd overtone percussion. Turning this setting on applies a second overtone percussion
sound.
Off, On
Perc.3rd
3rd overtone percussion. Turning this setting on applies a third overtone percussion
sound.
Off, On
Perc.Decay
Percussion decay time. Specifies the decay time of percussion sound.
0 to 127
On Click
Key on click. Turns the click sound when a key is pressed on or off.
Off, On
Off Click
Key off click. Turns the click sound when a key is released on or off.
Off, On
Type
Wave type. Selects either a sine wave or detune for the drawbar tone basic wave.
Sin, Vin
Vib.Rate
Vibrato rate. Specifies the vibrato rate (frequency).
0 to 127
Vib.Depth
Vibrato depth. Specifies how vibrato is applied.
0 to 127
Rot.Setting >Ent
Rotary setting. Group of settings for the
2 ROTARY SLOW/FAST function.
Button assign. Selects the DSP parameter (page E-88)*1 assigned to 2 ROTARY
Off, 1 to 8 *1
On Value
On value. DSP parameter value when the above button is on (lit).
*2
Off Value
Off value. DSP parameter value when the above button is off (unlit).
*2
Button Assign
SLOW/FAST.
*1: Depends on the currently selected DSP parameter (page E-88).
ROTARY SLOW/FAST.
*2: Range of the DSP parameter assigned to
2
■ Editable Parameters Common to Other Tone Categories
See “Other Editable Items” on page E-29.
E-32
Selecting and Creating Tones
Editable PCM Melody Tone (Non-drum PCM Tones) Parameters
There are two types of parameters: PCM melody tone specific editable parameters and the same parameters that apply to the
other tone categories.
The drum sets in the Variance category of the PCM tones have different editable parameters. See “Editable Drum PCM Tone
Parameters” for more information about them.
■ Editable Non-drum Set PCM Tone Parameters
Preparation
Display the screen in step 2 of the procedure under “To edit and save a tone as a user tone” on page E-21.
Editable Parameter List
Display Text
Description
Settings
Atk.Time
Attack time. Specifies the time it takes to reach peak value from note on.
–64 to 0 to +63
Rls.Time
Release time. Specifies the time it takes for a sustained sound to decay after a key is released.
–64 to 0 to +63
Cutoff
Cutoff frequency. Specifies the tone cutoff frequency.
–64 to 0 to +63
Vib.Type
Vibrato type. Specifies one of the wave types below to be used for vibrato.
Sin (sine wave), Tri (triangular wave), Saw (sawtooth wave), Sqr (square wave)
Sin, Tri, Saw, Sqr
Vib.Depth
Vibrato depth. Specifies how vibrato is applied.
–64 to 0 to +63
Vib.Rate
Vibrato rate. Specifies the vibrato rate (frequency).
–64 to 0 to +63
Vib.Delay
Vibrato delay. Specifies the delay in the timing for applying vibrato.
–64 to 0 to +63
Oct.Shift
Octave shift. Changes the tone of notes in octave units.
–2 to 0 to +2
TouchSense
Touch sense. Specifies the degree of change in volume in accordance with change in keyboard
playing touch.
–64 to 0 to +63
■ Editable Parameters Common to Other Tone Categories
See “Other Editable Items” on page E-29.
E-33
Selecting and Creating Tones
Editable Drum PCM Tone Parameters
The editable parameters described here are for the drum set tones in the Variance tone category. There are two types of
parameters: PCM drum tone specific editable parameters and the same parameters that apply to the other tone categories.
■ Editable Drum Set PCM Tone Parameters
Preparation
Display the screen in step 2 of the procedure under “To edit and save a tone as a user tone” on page E-21.
Editable Parameter List
• Shaded cells indicate a group made up of multiple items. Press
bq ENTER to display the items that make up a group.
Display Text
Description
Settings
Instrument edit. Group of editable drum tone parameters for each
keyboard.
• Press a keyboard key to specify the keyboard to be edited.
• This group can be entered by performing step 1 under “To edit and save
EDIT.
a tone as a user tone” (page E-21) and then holding down
Inst Edit >Ent
(C-1 to G9)
7
Instrument select. Group of editable tone parameters. Keyboard key
pressure (Velocity) is divided into four velocity ranges. Each range can be
configured to sound a different tone (Inst Number).
PART minus (–) and plus (+) buttons to select the range
• Use the
you want to edit.
9
Inst Number
Inst Select >Ent
0
[1]
[2]
[3]
[4]
range 1
range 2
range 3
range 4
[1]
[2]
[3]
Cannot be
specified.
[4]
127 Velocity
Velocity Range Hi
Inst Number
Instrument number. Selects the drum tone wave assigned to each
velocity range.
• See the separate “Appendix” for details about wave types.
VelRangeHi
See the separate
“Appendix”.
Velocity range high. Determines the high limit of each velocity range.
0 to 127
Volume
Volume. Specifies drum sound volume.
–128 to 0 to +127
Pan
Pan. Specifies the stereo position of drum sound.
–64 to 0 to +63
Rev.Send
Reverb send. Specifies how reverb is applied to a drum tone.
0 to 127
NoteOffMode
Note off mode. Turning on this setting causes note off to be performed
when a key is released.
Off, On
Assign Grp
Assign group. Specifies as a value from 1 to 15 which group the currently
selected keyboard should be placed into. Only one keyboard in a group is
sounded at any time (non-polyphonic).
Off, 1 to 15
Pitch LFO >Ent
Pitch LFO. Group of editable LFOs applied to pitch. Group items and
setting ranges are the same as “LFO (Pitch LFO)” under “Editable
Parameters for All Layers (Layer 1 through Layer 6)” (page E-31).
Refer to the cell to the
left.
Amp LFO >Ent
Amp LFO. Group of editable LFOs applied to volume. Group items and
setting ranges are the same as “LFO (Amp LFO)” under “Editable
Parameters for All Layers (Layer 1 through Layer 6)” (page E-31).
Refer to the cell to the
left.
■ Editable Parameters Common to Other Tone Categories
For information about Solo Synthesizer tones, see “Other Editable Items” on page E-29.
E-34
B
Selecting and Creating Tones
Controlling Sounds
You can use a pedal, the bender, or other devices, to instantly
change the pitch and volume of notes, the envelope, and
other parameters as you perform.
Using a Pedal
A pedal operation can be used to sustain notes, arpeggios
(page E-40), or phrases (page E-44), or to apply a soft effect.
• For information about connecting a pedal, see page E-8.
• You can specify the effect applied by a pedal operation by
performing the following operation on the performance
editing list: Controller >Ent 3 Pedal. See page E-65 for
more information.
Using the Wheels (Bender, Modulation)
bs
The
BENDER wheel can be use to seamlessly raise or
lower the pitch of a sound, while the
MODULATION wheel
adds vibrato (modulation effect) to the sound.
bs
bs
Hex layer tones (page E-30)
K1 : Cut off Frequency (Layer 1 to 6 individual) (page E-30)
K2 : Detune (Layer 1 to 6 global) (page E-31)
K3 : Attack Time (Layer 1 to 6 individual) (page E-30)
K4 : Release Time (Layer 1 to 6 individual) (page E-30)
Drawbar organ tones (page E-32)
K1 : Vibrato Rate
K2 : Vibrato Depth
K3 : Percussion Decay Time
K4 : Reverb Send (Same as other tone categories.)
PCM melody tones (page E-33)
K1 : Cut off Frequency
K2 : Attack Time
K3 : Release Time
K4 : Reverb Send (Same as other tone categories.)
PCM drum tones (page E-34)
K1 : Volume (Drum Inst >)
K2 : Pan (Drum Inst >)
K3 : Reverb Send (Drum Inst >)
K4 : Reverb Send (Same as other tone categories.)
The above functions show the abbreviated names used on
the tone mode screen.
Raises and lowers pitch.
(Releasing wheel returns
to original pitch.)
Applies modulation.
(Raising wheel
applies modulation.)
• Do not have a wheel rotated as you turn on Synthesizer
power.
• You can control the bend range of the
BENDER wheel
by configuring the following settings on the performance
editing list: BendRngDwn, BendRngUp (page E-64).
bs
• You can change the operations currently assigned to the
assignable knobs by performing the following operation on
the on the performance editing list (page E-65):
Controller >Ent 3 K1 to K4.
Using the Assignable Knobs
3
The four
ASSIGNABLE KNOBS can be assigned
functions that enable instant adjustment of a sound attack
time and other envelope parameters (page E-22), volume,
and more.
3
• The following shows the knob functions for each Zone Part
1 tone category.
Solo Synthesizer tones (page E-24)
K1 : Cut off Frequency (Block (7)) (page E-27)
K2 : Resonance (Block (7)) (page E-27)
K3 : Attack Time (Block (1) to (6) Amp >Envelope >)
(page E-26)
K4 : Release Time 1 (Block (1) to (6) Amp >Envelope >)
(page E-26)
E-35
Selecting and Creating Tones
Using Sliders
Using the Hold Button
5
You can used the nine sliders ( ) to adjust the volume
balance between the multiple sounds (see below) that make
up a tone, and to make simple adjustments in some DSP
parameters.
Solo Synthesizer tones : Volume settings of lock (1) through
(6) (Amp >Volume, page E-26)
Hex Layer Tones
: Volume of Layers 1 through 6
(Volume, Page E-30)
Drawbar Organ Tones : Pull out amount of nine drawbars
(Ft16' through Ft1', page E-32)
1
5
When you select a tone, the button ( ) that corresponds to
its category lights, and the sliders ( ) and the three buttons
( ) are assigned functions that correspond to the tone
category.
2
Labels show names of adjustable parameters.
bm
When the
HOLD button is lit (by pressing it), the currently
sounding note, arpeggio (page E-40), or phrase (page E-44)
will be sustained.
bm
Lights when HOLD is on.
bm
• Pressing
HOLD again will cause its light to go out,
indicating that hold is turned off.
Changing the Pitch of Notes in Semitone
Steps (Transpose) or Octave Steps (Octave
Shift)
br
PARAM A, PARAM B of current DSP type (page E-88)
Block (1) to (6)
volume
Tone category
selection
Main volume
(page E-29)
You can use the
TRANSPOSE and OCTAVE (–, +)
buttons to change the pitch of the keyboard notes in
semitone or octave steps.
• For information about fine tuning the pitch in hertz steps
(Tuning), see page E-69.
1. To change the pitch in semitone steps, hold
Layer 1 to 6 volume
br
down
TRANSPOSE as you press the
OCTAVE minus (–) or plus (+) button.
1
br
• The setting range for this operation is one octave
upwards and downwards (–12 semitones to +12
semitones).
5
2
Drawbar feet
Functions during drawbar organ tone selection*
ROTARY SLOW/FAST : Toggles the rotation speed between slow
(SLOW, button unlit) and fast (FAST,
button lit).
PERCUSSION SECOND : 2nd overtone percussion (page E-32)
PERCUSSION THIRD : 3rd overtone percussion (page E-32)
* During selection of a non-drawbar organ tone, the leftmost button
is assigned the Step Sequencer key shift function (page E-51).
The other two buttons are disabled.
• In the Performance Mode or Step Sequencer Mode, you
can use the
buttons (HEX LAYER, etc.) to edit tones
with the sliders without changing to another mode.
• Adjustment with the sliders is not possible for PCM tones.
• For more information about slider functions, see page E-49
for the Step Sequencer Mode and page E-67 for the Mixer
Mode.
1
E-36
br
Selecting and Creating Tones
2. To change the pitch in octave steps, use the br
OCTAVE minus (–) and plus (+) buttons
(without holding down
TRANSPOSE).
br
• The setting range for this operation is three octaves
upwards and downwards (–3 octaves to +3 octaves).
br
(1) Reverb
Adds reverberation to make it sound like
you are playing in a room or in a hall.
(2) Chorus
Combines multiple layers of the same note
to create a sound with more depth.
(3) Normal
DSP
A collection of versatile Normal DSP
effects help to enhance the sound of tones.
For example, distortion can be applied to
an electric guitar sound to make it sound
more powerful. There are 46 different
Normal DSP types, and the most
appropriate one for the selected tone is
applied automatically.* A DSP can be
edited and saved as a user DSP.
One of the elements that makes up a Solo
(4) Solo
Synthesizer Synthesizer tones. See “(7) Total Block” in
the “Editable Solo Synthesizer Tone
DSP
Parameters” on page E-22. There are six
Solo Synthesizer DSP types. When you
edit a Solo Synthesizer DSP, it is saved as
part of a Solo Synthesizer user tone. You
cannot save it as a user DSP.
(5) Master
Equalizer
• While the setting screen shown above is displayed you can
the
dial or the
minus (–) or plus (+) buttons to
change the setting. If you do not perform any operation for
a while, the setting screen will be exited automatically.
bo
bq
Applying Effects to Notes
You can apply reverb, vibrato, and other effects to notes to
enhance their sound.
■ Effect Block Diagram
Sound
Source
(4) Solo
Synthesizer
DSP
■ Chorus and DSP Use Restrictions
Under this condition:
Output
(2) Chorus
(3) Normal DSP
* When a tone with DSP (tone that uses a particular DSP)
that is not a Solo Synthesizer tone is selected. A tone with
DSP will have “DSP” next to its display name on the mixer
screen (page E-67) or performance editing screen (page
E-64).
Only one of the three effect types (Chorus, Normal DSP, Solo
Synthesizer DSP) can be enabled at any time.
(5) Master
Equalizer
(1) Reverb
Adjusts the frequency characteristics of the
Synthesizer’s notes. The Master Equalizer
can be used to adjust the frequency and
gain of four frequency bands: low, mid1,
mid2, and high.
Goes through (2), (3),
or (4). Also refer to
the “Chorus and DSP
Use Restrictions”
below.
And effects are
This type of
applied to each
effect is valid:
part like this:
(2) Chorus
Chorus Mode
• A tone other than
the Song Sequencer
is selected by Zone
Part 1, and the
Chorus is selected
by “Chorus/DSP
Select” (page E-38).
Depends on the
mixer chorus
send value
(page E-68) and
the selected
tone chorus
send value
(page E-29).
Normal DSP Mode
(3) Normal DSP
• A tone other than
the Song Sequencer
is selected by Zone
Part 1, and the DSP
is selected by
“Chorus/DSP
Select” (page E-38).
(3) is applied
only to parts
whose mixer
DSP line (page
E-68) is on.
Solo Synthesizer Tone
Mode
• Solo Synthesizer
tone selected by
Zone Part 1.
(4) is applied
only to Zone
Part 1 and parts
whose mixer
DSP line is on.
(4) Solo
Synthesizer
DSP
E-37
Selecting and Creating Tones
To configure effect settings
1. Hold down bm EFFECT until the effect list top screen shown below appears.
bm
2. Next, refer to the list below as you perform operations with the bq controls to select items and change
settings.
■ Effect Settings
Display
Description
Settings
Rev Type
Reverb type. Reverb effect type.
Type1, Type2
Rev Level
Reverb level. Reverb effect level.
0 to 127
Rev Time
Reverb time. Reverb sustain time.
0 to 127
Cho Level
Chorus level. Chorus effect level.
0 to 127
Cho Rate
Chorus rate. Rate of chorus effect undulation.
0 to 127
ChoSendRev
Chorus send level to reverb. Specifies how reverb is applied to the entire sound to which
the chorus effect is being applied.
0 to 127
Cho/DSP
Chorus/DSP select. Selects use of either Chorus or Normal DSP (“Chorus and DSP Use
Restrictions”, page E-37).
Cho, DSP
DSP Select >Ent
Displays the main Normal DSP selection screen.
• You will not be able to go any further if a Solo Synthesizer tone is selected for Zone Part
1.
(Normal DSP
selection
screen)
You can select from among preset and user tones for the Normal DSP using the same
procedures as those for tone selection.
• For a list of preset Normal DSPs, see the separate Appendix. Selecting “ton” applies the
initial preset DSP of each tone.
• Param A and Param B (page E-88) for the currently selected DSP type appear on the
K1 and K2.
display. You can adjust these parameters using
• Pressing
EDIT while this screen is displayed will change to the DSP editing screen
(page E-39).
7
Master EQ >Ent
Master equalizer setting group (item (5) of the “Effect Block Diagram” on page E-37)
EQ Enable
E-38
3
ton
Preset: 0-0 to 9-9
User: 0-0 to 9-9
Turning this setting off disables the Master EQ setting.
Off, On
Low Freq
Low frequency band. Adjusts the low frequency band.
200Hz, 400Hz,
800Hz
Low Gain
Low gain. Adjusts the low gain.
–12 to 0* to +12
Mid1 Freq
Mid 1 frequency band. Adjusts the mid1 frequency band.
1.0kHz to 5.0kHz
Mid1 Gain
Mid1 gain. Adjusts the mid gain.
–12 to 0* to +12
Mid2 Freq
Mid 2 frequency band. Adjusts the mid2 frequency band.
1.0kHz to 5.0kHz
Mid2 Gain
Mid2 gain. Adjusts the mid2 gain.
–12 to 0* to +12
High Freq
High frequency band. Adjusts the high frequency band.
6.0kHz, 8.0kHz,
10.0kHz
High Gain
High gain Adjusts the high gain.
–12 to 0* to +12
Selecting and Creating Tones
Saving an Edited DSP
DSPs are divided among 53 DSP types according to effects.
Preset Normal DSPs 0-0 and 0-1 are compressor type DSPs.
There are two DSP types: a Normal DSP specific type and a
Solo Synthesizer DSP specific type.
When editing and saving a DSP, you must first specify its type
and then edit it in accordance with its type.
• For a list of DSP types, see “DSP Type List” on page E-87.
1. Select the tone to which you want to apply the
DSP. Next, on the editing screen of the tone,
select DSP Edit >Ent (page E-29) and then press
ENTER to display the DSP editing screen
shown below.
bq
• When editing a Normal DSP, you can display the DSP
editing screen from the Normal DSP selection screen
(page E-38) by pressing
EDIT.
7
DSP type number: type name
DSP parameter
2. Use the bo dial to select a DSP type number.
3. Use the same operation as these for tone
editing (page E-21) to select and configure the
DSP parameters on the screen.
• DSP parameters depend on the DSP type. For details,
see the “DSP Parameter List” (page E-88).
4. After you finish editing a DSP, save it as
described below.
7
Press
WRITE to display the screen for saving a user
tone. Save the data as a user tone (page E-12).
• If you displayed the DSP editing screen from the
Normal DSP selection screen (page E-38) in step 1
Press
WRITE to display the screen for saving a
DSP. Save the edited DSP as a user DSP using the
same operation as that for a user tone.
7
■ Saving a User DSP to an External Device
• Memory card (page E-73)
• Computer (page E-79)
E-39
Sounding Arpeggio Phrases Automatically
bm
7
bo
bq
4
2
5
bk
With the Arpeggio Function, you can play various arpeggios
automatically by simply pressing keys on the keyboard. You
can select from a number of different arpeggio options,
including playing arpeggios from a chord, playing various
phrases automatically, and more.
• The Arpeggio Function has 100 arpeggio type presets. A
type presets can be edited and saved as a user arpeggio
type. There is memory for up to 100 user arpeggio types.
• The following functions are also available for selecting an
arpeggio type.
Hold (HOLD) : The arpeggio continues to play after
keyboard keys are released. This is useful,
for example, when you use the Split
Function to insert an arpeggio on one part
of the keyboard.
Sync (SYNC) : The Step Sequencer automatically plays
and stops in sync with the Arpeggio
Function when keyboard keys are pressed.
To use the Arpeggio Function
1. Hold down bm ARPEGGIO until the arpeggio
type selection screen shown below appears on
the display.
Arpeggio bank and number
Arpeggio name
2. Select a preset or user arpeggio type.
• To select an arpeggio type, perform the same operation
as steps 3 through 6 for selecting a tone (page E-20).
• If you want to turn on the hold function (HOLD), press
STEP +. Each press toggles HOLD between on and
off.
OFF : The arpeggio will play while keyboard keys are
depressed.
ON : The arpeggio will continue to play even after the
keyboard keys are released
• If you want to turn on the sync function (SYNC), use
STEP – to cycle through the available sync settings
described below.
OFF : Sync setting is turned off.
ON : Arpeggio play is synced with only the play
operation of the Step Sequencer.
S/S : Arpeggio play is synced with both the play and
stop operations of the Step Sequencer.
• The HOLD and SYNC settings are performance
parameters.
bk
bk
3. Press some keys and the arpeggio will start to
play automatically.
bm
• To turn off the Arpeggio Function, press
ARPEGGIO again.
• To stop arpeggio HOLD playback, press
ARPEGGIO or change the HOLD function in step 2 of
the above procedure to OFF.
bm
■ You can use the arpeggio type selection screen
to select the recommended tone for the currently
selected arpeggio type as your Zone Part 1 tone.
1. Hold down bm ARPEGGIO until the arpeggio
type selection screen appears on the display.
2. Hold down 7 EDIT until bm ARPEGGIO starts
Hold setting
Sync setting
to flash and then stops flashing to remain lit.
• In the case of a user arpeggio, the tone that was
selected as the Zone Part 1 tone when the user data
was saved is the recommended tone.
E-40
Sounding Arpeggio Phrases Automatically
5. Use the bo dial or the bq minus (–) and plus (+)
Editing an Arpeggio
There are two arpeggio types: step type and variation type.
• With a step type arpeggio, you can edit its steps and its
parameters. A step type arpeggio can contain up to 16
steps. You can change the following values for each step.
TYPE : Specifies the relative position in the arpeggio
pattern where each of the keyboard notes will play.
You can specify positions starting from the lowest
note played (L1) or from the highest note played
(U1). You can even specify simultaneous play of up
to five notes (P2 through P5).
NOTE: Specifies a relative shift, in semitone steps, from
the note played on the keyboard.
VELO : Specifies the volume of the note.
• With a variation type arpeggio, you can edit only its
parameters.
buttons to change the TYPE, NOTE, and VELO
settings.
4
• You can also use the
1 to 16 buttons to toggle
each step on or off.
• While TYPE is selected, use the
minus (–) and
plus (+) buttons to turn the TYPE setting on or off.
• You can use
(eight sliders excluding “MASTER”) to
change the values of the applicable step directly. When
using the sliders, press
1-8/9-16 to toggle between
steps 1 through 8 (button unlit) and steps 9 through 16
(button lit). Note, however, that you will not be able to
use the sliders when TYPE is TIE and OFF.
• You can specify the tie setting. For details how, see “To
configure tied note settings” on page E-52.
• The table below shows the contents of the arpeggio
step editing menu.
bq
5
2
1. Hold down bm ARPEGGIO until the arpeggio
type selection screen shown below appears on
the display.
2. From among the preset or user arpeggio types
select the arpeggio type you want to edit.
• To select an arpeggio type, perform the same operation
as steps 3 through 6 for selecting a tone (page E-20).
3. Press 7 EDIT.
4. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to “Step
Edit”, and then press
ENTER.
bq
• The “Step Edit” option will not be displayed if you
selected a variation type arpeggio in step 2 above.
Step type
Step number
E-41
Sounding Arpeggio Phrases Automatically
Menu Layer
Description
1
Settings
2
Step Edit >Ent
Specifies the relative position in the arpeggio pattern where the keyboard notes will play starting
from the lowest note played (which is L1).
• If the number of keys pressed is less than the number of configured type (L) settings (i.e. if you
press only three keyboard keys for an arpeggio pattern that includes settings for L1 through L6),
the arpeggio pattern will repeat, playing the keyboard key notes one octave higher.
• At any point the above causes the range of one higher octave to be exceeded, arpeggio play will
return to the L1 note automatically.
L1 to L8
Specifies the relative position in the arpeggio pattern where the keyboard notes will play starting
from the highest note played (which is U1).
• If the number of keys pressed is less than the number of configured type (U) settings (i.e. if you
press only three keyboard keys for an arpeggio pattern that includes settings for U1 through
U6), the arpeggio pattern will repeat, playing the keyboard key notes one octave lower.
• At any point the above causes the range of one lower octave to be exceeded, arpeggio play will
return to the U1 note automatically.
U1 to U8
Specifies how many of the notes played on the keyboard, starting from the highest note played,
should be played simultaneously.
• When the number of keys pressed is less than the polyphony (P) value specified here, only the
notes that are played are sounded.
P2 to P5
NOTE
Shifts the notes produced by pressing keys in semitone steps.
–24 to +24
VELO
Changes the velocity of pressed keys.
–64 to +63
TYPE
6. After the TYPE, NOTE, and VELO settings are the way you want, press bq EXIT to return to the arpeggio
menu screen.
7. Use the bq up (q) and down (w) buttons to move the item selection cursor (0) to “Parameter”, and
bq ENTER.
8. Use the bo dial or the bq minus (–) and plus (+) buttons to change the parameter settings.
then press
• The table below shows the contents of the parameter editing menu.
Menu Layer
Description
1
Settings
2
Parameter >Ent
Max Step
Maximum step. Can be edited only by step type.
1 to 16
Step Size
Step size. Specifies the note length between steps.
2, 6,
NoteLngth
Note length. Specifies the length of the note that is sounded as
a percentage of the step size. (100% for the same length as
the original, 50% for half the original.)
1 to 100%
Groove
Groove. Specifies the timing of the off-beat step. (50% for
even. Larger values increase the length of the first half of the
note.)
10 to 90%
Grv.Type
Groove type. Specifies the note length when the Groove
setting is anything besides 50%.
Norml: Plays back at the actual percentage of the
step length.
Short: Adjusts to a short step in accordance with the
step.
Velocity
Velocity. Specifies the velocity of an input arpeggio. Specifying
KeyOn inputs a velocity value in accordance with the degree
of key pressure applied.
KeyOn, 1 to 127
Hold Pedal
Hold pedal. Specifies on/off switching for hold used by a pedal. On, Off
, 7,
,8
9. After you finish arpeggio parameter editing, save it as described below.
7
• Press
WRITE to display the screen for saving arpeggio data. Save the arpeggio by performing the same operation as
that for saving a user tone (page E-12).
• For information about deleting data you saved, see page E-71.
■ Saving Arpeggio Data on an External Device
• Memory card (page E-73)
• Computer (page E-79)
E-42
Sounding Arpeggio Phrases Automatically
Clearing Arpeggio Data
Use the procedure below to clear preset step data or step
data that was edited using Step Edit (page E-42) and create
new step data from scratch.
• Note that variation type data cannot be cleared.
1. Hold down bm ARPEGGIO until the type
selection screen shown below appears on the
display.
2. From among the preset or user arpeggio types
select the arpeggio type you want to clear.
• The procedure for selecting an arpeggio type is the
same as that for selecting a tone (page E-20).
3. Press 7 EDIT.
4. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to “Clear
Step”, and then press
ENTER.
bq
5. Press bq ENTER again.
This should cause “Clear?” to appear on the display.
6. Press bq YES.
The message “Complete!” will appear on the display when
the data is cleared.
E-43
Recording and Playing Back Phrases
7
bn
bp
bq
bk
The Phrase Sequencer is a great way to record musical
phrases that suddenly pop into your mind for later playback.
• The Sequencer has 100 preset phrases.
• You can record a new phrase or overdub onto an existing
phrase to create a user phrase. There is memory for
storage of up to 100 user phrases for later recall when you
need them.
• In addition to what you play on the keyboard, your pedal,
wheel, and knob operations are also recorded as part of
phrase.
• You can choose either of two different playback options:
one-time playback (loop off) or repeat playback (loop on).
• Overdubbing during looped playback is supported. You
also can temporarily cancel overdubbing and perform
looped playback only.
• Pressing a keyboard key will start playback of the phrase
from the corresponding pitch (Key Play).
To play back a preset
phrase selection screen shown below appears
on the display.
Loop setting
E-44
play.
• To select a phrase number, perform the same
operation steps 3 through 6 for selecting a tone (page
E-20).
3. Press bk STEP + to toggle looping between on
and off.
OFF : One-time playback
ON : Looped playback
4. Press bk STEP – to toggle hold between on and
off.
bn
PLAY/STOP is
OFF : Phrase plays back only while
depressed, and stops when the button is released.
ON : Phrase playback starts when
PLAY/STOP is
pressed and stops when
PLAY/STOP is
pressed again.
bn
bn
5. Press bn PLAY/STOP to start phrase playback.
1. Hold down bn KEY PLAY until the preset
Phrase name
2. Select the number of the phrase you want to
Phrase number
Hold setting
bn
• If the phrase is looped, the
PLAY/STOP light will go
out momentarily to indicate when playback returns to
the beginning of the phrase.
• You can also use the above procedure to play back
user phrases as well.
• Phrase loop and hold settings are saved as parameters
for each phrase.
Recording and Playing Back Phrases
To change the tempo setting
There are two different methods you can use to change the
tempo setting: using the TEMPO buttons or tapping a beat
with a button.
• You can use this procedure to adjust the tempo not only for
phrases, but also for other functions as well.
■ To change the tempo using the TEMPO buttons
1. Press the 8 TEMPO – (slower) or 8 TEMPO +
(faster) button.
• This displays the tempo screen shown below.
You can use the phrase selection screen to
select the recommended tone for the currently
selected phrase as your Zone Part 1 tone.
1. Hold down bn KEY PLAY until the phrase
selection screen appears on the display.
2. Hold down 7 EDIT until bn KEY PLAY starts to
flash.
• In the case of a user phrase, the tone that was selected
as the Zone Part 1 tone when the user data was saved
is the recommended tone.
To start phrase playback by
pressing keyboard key (Key Play)
1. Press bn KEY PLAY so the button becomes lit.
2. Press keyboard key to start playback of the
phrase.
• If you do not perform any operation for a few seconds,
the display will return to previous screen automatically.
2. Use the 8 TEMPO –, + buttons to change the
tempo (beats per minute).
• Holding down either button or rotating the dial will scroll
the tempo values at high speed.
• You can specify a tempo value in the range of 30 to
255.
3. Press the bq EXIT button.
• This exits the tempo screen.
• If the key you press to start phrase playback is higher
or lower than the phrase’s original pitch, the phrase will
play at the pitch of pressed key.
• When the hold setting is turned off, the phrase is played
only while the keyboard key is depressed, and stops
when the key is released. When the hold setting is
turned on, phrase playback starts when the keyboard
key is pressed and does not stop until the
PLAY/
STOP key is pressed.
• You can use the “Phrase Key Range Lo” and “Phrase
Key Range Hi” settings to specify the high point and the
low point of the keyboard where Key Play can be
performed (page E-66).
bn
■ To adjust the tempo by tapping a beat
1. TAP the 8 TAP button four times at the speed
(tempo) you want to set.
• The tempo setting will change in accordance with your
tapping speed as soon as you tap the fourth time.
2. After setting the tempo by tapping, you then
can use the procedure under “To change the
tempo using the TEMPO buttons” (page E-45) to
make fine adjustments.
E-45
Recording and Playing Back Phrases
Recording a New Phrase
In addition to what you play on the keyboard, pedal, knob, and
wheel operations are also recorded in phrases.
• You can record up to approximately 1,600 notes for a single
phrase. Also, recorded wheel and knob operations
significantly reduce the remaining number of notes
available for recording.
1. Press bn REC.
bn
This will cause the
REC light to flash.
• If OVDB (overdubbing) is displayed as the “Rec Mode”
setting, use the
minus (–) and plus (+) buttons to
change it to NEW (new phrase). This will enter the new
phrase recording standby mode.
Menu
bq
• End quantize and note quantize settings can be
configured as required.
■ End Quantize (End Qntz)
When you perform a button operation to end recording of a
new phrase, there is a chance that your timing may be off.
The end quantize settings described below can be used to
correct the timing of the end point automatically and make its
positioning more natural.
Off : Phrase end point timing not adjusted.
1M : Phrase end point is adjusted to measure-unit
positions.
2 : Phrase end point is adjusted to quarter note-unit
positions.
6 : Phrase end point is adjusted to eighth note-unit
positions.
■ Note Quantize (Note Qntz)
When recording keyboard play, there may be cases when
your timing strays a bit. The note quantize settings described
below can be used to correct the timing of keyboard play
automatically and correct the timing of notes you play on the
keyboard. (Note that only key press timing is correct. The
timing of other operations such as key release, and wheel,
pedal, and knob operations are not corrected.)
Off
: Timing not adjusted. (Notes are
recorded as played.)
6,
, 7,
: Timing of actual keyboard play is
corrected to the nearest note in
accordance with the specified note unit.
bq
• Pressing
MENU will display a menu of the detailed
settings shown below. Use the
up (q) and down
(w) buttons to select a parameter and then use the
minus (–) and plus (+) buttons to change its
setting.
bq
E-46
bq
Description
Setting Range
Guide
Guide tone. Specifies whether
or not a count tone is sounded
Off, On
during phrase recording and/or
record standby.
Precount
Precount. Specifies the
number of measures of count Off,
to be inserted prior to the start 1:1 measure,
2:2 measures
of button operation triggered
phrase recording.
Beat
Beat. Specifies the beat when
2/4 to 8/4,
Guide, Precount, or end
2/8 to 16/8
quantize 1M is being used.
2. Recording will start when you press the bn
REC, or when you start to play by performing a
pedal, knob, or wheel operation or play
something on keyboard.
bn REC will light when recording starts.
3. When recording reaches the point where you
want to stop, press
bn
bn PLAY/STOP.
REC will become unlit and “!TEMP” (temporary) will
appear for the phrase number.
• Pressing
REC in place of
PLAY/STOP in step 3
above will stop recording, temporarily change to the
overdub standby mode, and start looped playback of
the phrase you have recorded. For details about
overdubbing, see “Recording Over Another Phrase
(Overdubbing)” (page E-47).
bn
bn
4. After you finish recording, save the data as
described below.
7
• Press
WRITE to display the screen for saving a
phrase (page E-48).
• For information about deleting data you saved, see
page E-71.
■ Saving a Phrase to an External Device
• Memory card (page E-73)
• Computer (page E-79)
Recording and Playing Back Phrases
5. After you finish configuring settings, save them
Phrase Data Settings
When playing on keyboard to start phrase playback (page
E-45), the phrase data will play back in the key it was
originally recorded in (Original Key) if you press the key for
the first note recorded in the phrase.
Phrase data settings can be used to specify that playback
should be performed using the originally recorded notes, even
when keyboard keys are pressed for notes other than those in
the original phrase data. Each phrase has a Key Shift setting
that you can use to change the pitch of the original key in
semitone steps.
as described below.
7
• Press
WRITE to display the screen for saving a
phrase (page E-48).
• For information about deleting data you saved, see
page E-71.
■ Saving a Phrase to an External Device
• Memory card (page E-73)
• Computer (page E-79)
Recording Over Another Phrase
(Overdubbing)
1. Hold down bn KEY PLAY until the phrase
selection screen appears on the display.
2. Select the number of the phrase whose settings
you want to configure.
• To select a phrase number, perform the same
operation steps 3 through 6 for selecting a tone (page
E-20).
3. Press 7 EDIT.
1. Select the phrase you want to overdub.
• To select a phrase, perform the same operation steps 3
through 6 for selecting a tone (page E-20).
2. Press bn REC.
bn
This will cause
REC to flash.
• If NEW is displayed as the “Rec Mode” setting, use the
minus (–) and plus (+) buttons to change it to
OVDB (overdubbing). This will enter the overdubbing
standby mode. A phrase number and name will be
shown on the display, but you cannot select a phrase at
this time.
bq
4. Use the bq up (q) and down (w) buttons to
bp
bq
select a parameter and then use
or the
minus (–) and plus (+) buttons to change its
setting.
Menu
OriginalKey
Key Shift
Description
Setting Range
Original Key. Specifies
the keyboard key that
corresponds to the first
note of the phrase played
by Key Play. (The initial
Original Key default
C– to G9
settings the note played
when the phrase was
recorded.)
• Setting can be
specified using the
keyboard keys.
Key shift. Specifies the
key shift, in semitone
steps, of a phrase when
the keyboard key
corresponding to the
original is or the PLAY/
STOP key is pressed.
(To disable key shift,
specify 000.)
• If you want, configure the note quantize (Note Qntz)
setting (page E-46) at this time.
3. Press bn REC or start playing with a pedal,
knob, or wheel operation, or by playing
something on the keyboard. Any one of these
operations will start overdub recording.
bn
bn
This will cause
REC and
PLAY/STOP to light
(without flashing).
• The original phrase will playback as a loop. Anything
you play on the keyboard and any operations you
perform during loop playback will be overdubbed onto
the original phrase.
4. When recording reaches the point where you
want to stop, press
bn PLAY/STOP.
bn REC and bn PLAY/STOP will become unlit and an
exclamation point (!) will appear next to the phrase
number.
–127 to 000 to
+127
E-47
Recording and Playing Back Phrases
■ To pause overdubbing during looped playback
bn
In step 4 of the above procedure, press
REC instead of
PLAY/STOP.
• This will cause
REC to start flashing.
• Though what has been recorded up to that point continues
to play as a loop, further recording is not possible while
overdubbing is paused.
• Press
REC again to resume overdubbing.
bn
bn
To save a phrase
Press 7 WRITE to display the screen for saving a phrase.
Save the phrase by performing the same operation as that for
saving a user tone (page E-12).
bn
■ To delete the last recorded data (undo)
While phrase playback is in progress or stopped, or while
overdubbing is in progress or paused, hold down
REC
until the undo screen appears.
bn
• The message “Can’t UNDO” will be appear on the display if
you try to perform an undo operation again after already
undoing the last recording.
• If there is not enough Synthesizer memory space available
to store the phrase data, the message “not enough space”
will appear on the above display in place of “Press Enter”,
and you will not be able to save the phrase data. If this
happens, delete some of the user data in Synthesizer
memory to free up memory space.
• The Synthesizer can store up to 100 user phrases with a
combined total of up to 128KB.
• For information about deleting phrase data you saved, see
page E-71.
■ Saving a Phrase to an External Device
• Memory card (page E-73)
• Computer (page E-79)
• A phrase that has been saved as a user phrase cannot be
undone.
Indicators Next to Phrase
Numbers
The meanings of the indicators that are appended to the
phrase number on the display are described below.
!
: Unsaved phrase
*
: Saved user phrase
! TEMP : Newly recorded phrase that has not been saved
• If you change the phrase number selection in step 2 of the
procedure under “To play back a preset” while an
exclamation point (!) is appended to the currently selected
phrase number (indicating that it is an unsaved user
phrase), the unsaved user phrase will be discarded. To
save an unsaved user phrase, use the procedure under “To
save a phrase”, below.
E-48
Using the Step Sequencer
7
1
2
bm
bo
bp
bq
4
5
9
bk
bl
The Step Sequencer provides up to 16 steps. The Synthesizer’s sliders can be used to control step notes and velocity in real time.
The Step Sequencer is not just a rhythm machine, it makes it possible for you to compose music as you play on the keyboard.
You can edit each step of a preset sequence to create your own rhythm pattern and save the result as a user sequence.
• The Step Sequencer has 100 preset sequences. You also can store up to 100 of your own user sequences.
• There are two ways to edit a step: simple editing without using the editing screen, and the editing screen that provides more
detailed modification of a step.
• Wheel (bender, modulation) and knob operations can also be recorded as part of a sequence.
• Up to 99 different patterns can be chained together with the Step Sequencer and played back as a loop. You can store up to 100
chained sequences.
• Phrase Sequencer playback can be started from the Step Sequencer.
How the Step Sequencer is organized
The following describes the configuration of a single sequence.
• A part (PART) consists of nine note parts (Drum 1 to 5, Bass, Solo 1 and 2, Chord) and four control parts.
• The control parts can be configured with pitch bends/control changes and Phrase Sequencer play triggers (that start and stop
playback).
• For details about the settings and other information about each part, see “Editing a Sequence - Advanced” on page E-55.
• Each sequence has eight different patterns. You can configure separate beat (Beat Info) for each of the eight patterns.
• A track consists of data 16 steps along with their track parameters.
• You can use the Synthesizer’s mixer function to change Step Sequencer tones. For details, see “Using the Mixer” on page E-67.
E-49
Using the Step Sequencer
Sequence Parts
Patterns 1 through 8
(page E-49)
Part
(page E-49)
Note Part
Control Part
Sliders
(page E-52)
Beat
Drum 1
Track
Drum 2
Track
Drum 3
Track
Drum 4
Track
Drum 5
Track
Bass
Track
Solo 1
Track
Solo 2
Track
Chords
Track
Control 1
Track
Control 2
Track
Control 3
Track
Control 4
Track
A
A
A
A
A
A
A
A
A
Master Slider
(page E-53)
B
B
B
B
B
B
B
B
B
Mixer
(page E-67)
8ch
9ch
10ch
11ch
12ch
13ch
14ch
15ch
16ch
Track
Step Data
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Track Parameters
• Maximum step
• Step size
• Others
Control Type
• Control track only
Note Part
Off, On, Tie
Note 1
*Note 2
*Note 3
Velocity
* Control track only
Control Part
Value
E-50
Key shift
• Phrase only
Using the Step Sequencer
Playing Back a Step Sequence
A step sequence can be played back from the Performance,
Tone, or Step Sequencer Mode.
The step sequence can be changed by switching to a different
pattern, selecting a different sequence bank and number, and
by shifting the key (Key Shift).
3. If you want to change to a different sequence,
enter the Step Sequencer Mode and change the
sequence bank and/or number.
• To select a sequence, perform the same operation
steps 3 through 6 for selecting a tone (page E-20).
4. If you want to shift the key, press 1 STEP
SEQUENCER and then press
bk
• If the
CHAIN button is lit (indicating the Chain
Mode), press
CHAIN to turn off the light before
starting the procedure below.
bk
1. Press bk START/STOP.
bk
The
START/STOP button will flash and sequence
playback will start.
Sequence name
2 KEY SHIFT.
• When the original key is C2, you can shift the key by
pressing a keyboard key within the range of D2 to B2.
• You can specify whether or not to shift the key of each
individual part. For details, see the section of this
manual from “Editing a Sequence - Advanced” on page
E-55.
• The Key Shift on/off setting is saved as Performance
parameter.
Sequence bank, number
Editing a Sequence -Simple
Editing
Simple editing of a sequence can be performed from the
Performance, Tone, or Step Sequencer Mode.
bk
• If the
CHAIN button is lit (indicating the Chain
Mode), press
CHAIN to turn off the light before
starting the procedure below.
Tempo
Measure
Beat
bk
• Pressing
START/STOP while playback is in
progress will stop the sequence and cause the
START/STOP button light to go out.
• Step Sequencer playback can be performed
automatically, without pressing
START/STOP, by
using the Arpeggio Function to specify Step Sequencer
playback triggers. For details, see the section of this
manual from “To use the Arpeggio Function” on page
E-40.
• For information about changing the playback tempo,
see “To change the tempo setting” (page E-45).
bk
bk
2. To change to a different pattern, enter the Step
Sequencer Mode and press one of the
PATTERN 1 to 8 buttons.
bl
The light of the button whose pattern you select will go
out.
• When changing to a different measure, the light of the
button of the currently selected pattern will flash until a
point is reached where the change can be made.
• Pressing the button of the currently selected pattern will
cause its button light to flash, indicating that playback is
standing by to stop. Next, pressing
START/STOP
will stop playback when it reaches the end of the
currently playing measure. To cancel the stop standby
operation described above, press the flashing button
again.
bk
bk
1. If the Synthesizer is in the Performance or Tone
Mode, press
1 STEP SEQUENCER.
This enters the Step Sequencer Mode, which causes the
STEP SEQUENCER button to light.
1
2. Perform steps 1 through 3 of the procedure
under “Playing Back a Step Sequence” on page
E-51 to select the sequence and pattern you
want to edit.
3. Use the 9 PART minus (–) and plus (+) buttons
to select the part you want to edit.
A pointer (e) will appear on the display under the number
of the currently displayed part.
Selected part name
Selected part number
• The pointer (e) does not appear on the display if you
select a control type part.
4. Edit each part using the procedures in the
following sections.
E-51
Using the Step Sequencer
2. Next, while holding down 1 STEP
To turn a step on or off
4
■ On (Sounding)
4
Press the
1 to 16 button of the number of the step you
want to turn on.
When a step is on, its
1 to 16 button is lit and NOTE is
displayed next to its step number.
SEQUENCER, press the
1 to 16 button that
corresponds to the step number of the last note
of the tied group.
4
Last step number
■ Off (Not sounding)
4
Press the
1 to 16 button of the number of the step you
want to turn off.
When a step is turned off, the light of its
1 to 16 button is
unlit and OFF is displayed next to its step number.
4
• This turns on the step you specified as the start of the
tied group. It also ties together all of the notes from the
first step up to the last step.
• The
1 to 16 buttons that correspond to the step
numbers included in the tied group will all be flashing.
Release
STEP SEQUENCER and the button lights
will go out. (Even though the button lights go out, the
notes in the group remain tied.)
• To check which steps are tied, hold down
STEP
SEQUENCER and then press any one of the
1 to
16 buttons. This will cause the
1 to 16 buttons of
the steps included in the tied group to flash.
• A control part doe not have a tie setting.
4
1
1
4
• There is no step on/off setting for a control part.
To configure tied note settings
1. While holding down 1 STEP SEQUENCER,
4
Using the Sliders to Change Note and
Velocity Settings
4
press the
1 to 16 button that corresponds to
the step number of the first note of the tied
group.
1
1
• If the
STEP SEQUENCER button is not lit, press
STEP SEQUENCER to turn on the light before starting
the procedure below.
■ Slider Operations
5
First step number
Use
1/9 to 8/16 to change the note and velocity settings
(note part) of the notes of steps 1 through 16.
• In the case of a control part, the sliders can be used to
change the control effect. For details, see “Editing a
Sequence - Advanced” on page E-55.
• Press
1-8/9-16 to toggle slider operations between
steps 1 through 8 and steps 9 through 16.
• Step 1 through 8 operation is selected when the
1-8/
9-16 button is unlit. Step 9 through 16 operation is selected
when the
1-8/9-16 button is lit.
2
2
2
Steps 1 through 8 or steps 9 through 16 (selectable)
E-52
Using the Step Sequencer
■ Selecting a Slider Function
2
Pressing
FUNC A/B toggles the sliders between two
functions.
Example: Preset sequence
FUNC A/B unlit: L (NOTE)
FUNC A/B lit: M (VELOCITY)
2
2
3. Use the 9 PART minus (–) and plus (+) buttons
to select the part whose slider assignments you
want to change.
4. Press 2 FUNC A/B to select the set of sliders
(A or B) whose assignments you want to
change.
5. Move the display cursor to “TYPE” and then
bq
use the
NO and YES buttons to assign one
of the following functions to the selected
sliders.
Indicates the selected function as L or M.
5
1/9 to 8/16 slider will turn on the
• Moving a
corresponding step, even if it is currently turned off.
• Slider function switching cannot be performed for a
control part.
Using the Master Slider to Change Note and
Velocity Settings
NOTE
: Note
VELO
: Velocity
NOTE & VELO : Both note and velocity
6. Use the bo dial, the bq up (q) and down (w)
bl
buttons, or the
PATTERN (1 to 8) buttons to
move the display cursor to the slider position
(1 to 8) whose setting you want to change.
• The numbers 1 through 8 indicate the eight slider
positions, from top (8) to bottom (1).
5
You can use the
MASTER slider to batch change the
settings (note, velocity, staccato/tenuto, playback speed,
groove) of all of the parts.
• The settings that can be changed using the master slider
depend on the part type.
• For some parts, the master slider cannot be used to change
settings.
• You can assign other settings to the master slider, if you
want. For more information, see “Changing the Function
Assigned to the Master Slider” on page E-53 and
“Changing Slider Settings” on page E-59.
Changing Slider Assignments
Under default settings, the A sliders have note settings
assigned to them, while the B sliders have velocity settings
assigned. You can use the procedure below to assign note
settings, velocity settings, or both note and velocity settings to
sliders.
You also can specify the note or velocity setting that is
selected at each of the eight slider positions.
1. Press 1 STEP SEQUENCER.
2. Hold down 2 FUNC A/B until the SLIDER
screen shown below appears.
7. Use the bq NO and YES buttons to change the
note or velocity value at the currently selected
slider position.
• You can also press the keyboard key that corresponds
to the note you want to input to specify the note and
velocity for the currently selected slider position.
• For a chord part, you can specify up to three values.
Changing the Function Assigned to the
Master Slider
1. Press 1 STEP SEQUENCER.
2. Hold down 2 FUNC A/B until the SLIDER
screen appears.
3. Press bq MENU and then press the bq right (I)
button to move the item selection cursor (0) to
“M.Slider”.
E-53
Using the Step Sequencer
4. Press bq ENTER.
This will display the master slider setting screen.
Inputting Step Data by Playing on the
Keyboard, etc.
You can input note, velocity, and other step data by
performing keyboard, pitch bend, and knob operations as you
play.
• When inputting a pitch bend or knob operation, you first
need to use the control track to select the pitch bender or
knob and then perform in input.
1. Press 7 EDIT.
5. Use the bq minus (–) and plus (+) buttons and
9
the
PART minus (–) and plus (+) buttons to
display the name of the part you want to change
to inside the brackets % next to Part.
6. Use the bq up (q) and down (w) buttons to
move to the “Assign” setting, and then use the
dial or the
minus (–) and plus (+) buttons
to change to one of the settings described
below.
bo
bq
Assign
Description
Nop
No operation. Master slider operation is
disabled.
S. Data
Step data. Changes the data of all of the steps
(1 thorough 16) that are currently turned on.
S. Size
Step size
NoteLn
Note length
Groove
Groove
Octave
When there are notes assigned to sliders 1
through 8, moving the master slider when this
setting is in effect will change the octaves of
the notes (Range: –1 to 0 to 1).
• For details about step size, note length, and groove
assignments, see “Step Sequencer Parameters” on
page E-56.
2. Use the bq down (w) button to move the item
selection cursor (0) to “Step Edit”, and then
press
ENTER.
bq
3. Input data as described below.
■ While sequence playback is in progress
Press keyboard keys and perform other operations as
required according to the timing of playback.
■ While sequence playback is stopped
Perform input into the currently displayed step.
Changing the Solo1 Channel
Solo1 is normally assigned to channel 14.
You can use the procedure below to change the assignment
to channel 1 when you want to use Solo Synth or other special
tones as the solo tone.
1. Press 1 STEP SEQUENCER.
2. Press bq MENU and then press the bq right (I)
button.
3. After confirming that the item selection cursor
(0) is next to “Setting”, press
bq ENTER.
4. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to “Solo1
Ch”.
• Slider functions can also be modified as described below.
For information about making these changes, see
“Changing Slider Settings” on page E-59.
– Copying settings from another slider
– Scale, drum, velocity slider presets
– Note shift
5. Use the bq minus (–) and plus (+) buttons to
change the Solo1 channel setting.
1 : Channel 1
14 : Channel 14
• The Solo1 channel setting is saved as Performance
parameter.
E-54
Using the Step Sequencer
Changing the Timing of Pattern Switching
1. Perform steps 1 through 3 of the procedure
under “Changing the Solo1 Channel” on page
E-54.
2. Use the bq up (q) and down (w) to move the
item selection cursor (0) to “Pattern Change
Timing”.
To sound a single part
(solo mode)
1. Press 1 STEP SEQUENCER and then press
7 EDIT.
• This step is not necessary if you already pressed
EDIT and are already editing a step sequence.
7
2. Press bm MIXER.
3. Hold down the button (4 9 to 16 note part
buttons) that corresponds to the part you want
to solo.
• To cancel the solo setting, exit the Step Sequencer
Mode or display the Track On/Off screen (page E-56).
• For details about mixer operations, see “Using the
Mixer” on page E-67.
3. Use the bq minus (–) and plus (+) buttons to
select one of the pattern switching timings
described below.
Wait : Wait until the start of the next measure.
Real : Switch immediately, even if it is partway through a
measure.
• The pattern switching timing setting is saved as
Performance parameter.
Syncing Step Sequencer Playback with an
Arpeggio
Editing a Sequence - Advanced
You can use the procedures in this section for advanced,
detailed editing of sequence parameters.
To perform advanced parameter editing
1. Press 7 STEP SEQ.
2. Press 7 EDIT.
Mixer screen
See “To use the Arpeggio Function” on page E-40.
Changing the Step Sequencer
Tone
You can use the Synthesizer’s mixer function to change the
Step Sequencer tone.
• Data assigned by the mixer to channels 8 through 16 is
saved as Step Sequencer data.
• Mixer parameters are applied to all pattern parameters.
• For details, see “Using the Mixer” on page E-67.
3. Use the bq cursor (U, q, w, I) buttons to
move the item selection cursor (0) to the menu
item for the edits you want to perform.
E-55
Using the Step Sequencer
■ Step Sequencer Parameters
Level 1
Level 2
Level 3
Trk On/Off >Ent
Setting Range and
Screen Contents
Description
Track editing
EDIT while in the Step Sequencer Mode will
• Pressing
display the same screen as Trk On/Off >Ent.
7
Pattern
Pattern number
1 to 8
Part
Part name.
Drm1 to 5, Bass, Sol1 to 2, Chrd,
Ctl1 to 4
Track
1 to 16 to toggle.
Track on/off. Use
1 to 4 correspond respectively to Control Parts 1
•
through 4. In the same way,
8 to 16 correspond to
Note Parts (page E-50).
4
Step Edit >Ent
4
Off, On
4
Step editing. Step-specific editing group.
Drm1 to 5,
Bass,
Sol1 and 2
NOTE, VELO Selects off (OFF), on (NOTE), or tie (TIE) for a step. When
on, note (NOTE) and velocity (VELOCITY) parameter
settings are configured. The tie setting cannot be selected
for Step 1.
Off, (When on) NOTE: C– to G9,
(When on) VELO: 1 to 127, Tie
Note
Chrd
NOTE, VELO Selects off (OFF), on (NOTE), or tie (TIE) for a step. When
on, note (NOTE) and velocity (VELOCITY) parameter
settings are configured. The tie setting cannot be selected
for Step 1.
Velocity
Off, (When on) NOTE: Off or C– to
G9, (When on) VELO: 1 to 127, Tie
Notes of chord
Ctl1 to 4
Control part (Ctl) effects. Data of each part.
NOP: No operation. Other setting
ranges are as shown below.
Example screen shot below shows
PHRASE screen.
Menu
BEND
E-56
Pitch Bender
Velocity
Value
–128 to +127
CC1 to 97
MIDI control change.
0 to 127, Pan only –64 to +63
K1 to 4
Knob operations specified by a Performance, etc.
0 to 127
TEMPO
Tempo
30 to 255
PHRASE
Specifies triggers for starting and stopping Phrase
Sequencer playback. Display for Control 4 (Ctl4) only.
Nop: Disabled, Stop: Stop playback,
Start: Start playback,
–24 to +24: Shift from original key
(When Start is selected)
Using the Step Sequencer
Level 1
Level 2
Level 3
Track Param >Ent
Beat Info
Setting Range and
Screen Contents
Description
Track parameter
Max Step
1 to 16
Maximum step. Specifies the number of steps played back
by a part. If the specified maximum number of steps is
exceeded during playback, playback returns to the first step.
Step Size
Step size. Specifies the note length between steps.
2, 6,
NoteLngth
Note length. Note on note length specified as a percentage
of the step size. 100% specifies the same size as the
original, while 50% specifies a note length that is half the
original.
1 to 100%
Groove
Groove. Specifies the on note timing of the off-beat step.
The step note length changed alternately by step playback.
50% specifies even, while a larger value increases the first
half note length.
10 to 90%
Grv.Type
Groove type. Specifies the note on note length type when
anything other than 50% is specified for Groove.
Norml: Normal Playback performed
with length based on actual
percentage.
Short: When step length is changed
by Groove, adjusts to the shorter
length.
Ctrl.Ch
(Control part only)
Control Channel. Specifies the channel that applies the
Control Track effect.
Channel 1, 8 to 16
Smooth
(Control part only)
Smooth. Controls Control Track playback. When on, control
data is interpolated and played back
On, Off
Phrase No.
(Control part 4 only)
Phrase Sequencer number. Specifies the Phrase Sequencer
number to be controlled.
P00 to 99, U00 to 99
Key Shift >Ent
Key shift editing group. This setting cannot be configured for
Control 1 through 3. Real-time setting is not supported when
Control 4 is configured to perform Phrase Sequencer key
shift.
, 7,
,8
Enable
Key shift on/off
Off, On
BreakPoint
Point between C and B where key shift drops the octave
when the key is exceeded.
C to B
Realtime
Real-time. Specifies breakpoint timing.
On: Change immediately
Off: Change at the next note
Beat setting
2/4 to 8/4, 2/8 to 16/8
E-57
Using the Step Sequencer
Level 1
Level 2
Level 3
Copy >Ent
Description
Setting Range and
Screen Contents
Data copy
Track
Copies data from another track. Copies step data and part
parameter data.
• Data being edited (TMP) can also be copied.
• The following are parts that can be copied.
From
Dr1 to S2
Chord
Ctrl1 to 3
Ctrl4
3
3
3
3
To
Dr1 to S2
Chord
Ctrl1 to 3
Ctrl4
Copy source part name
Copy source pattern number
Copy source sequence
(bank, number)
Copy destination pattern
number
Copy destination part name
Pattern
Copy data from another pattern.
• Data being edited (TMP) can also be copied.
Copy source pattern number
Copy source sequence
(bank, number)
Copy destination pattern number
Note Shift >Ent
Note shift editing group
Shift
Specifies how much to shift in semitone steps.
Ptn
Specifies a pattern to be shifted.
01 to 08
Part
Specifies a part to be shifted.
Dr1 to 5, Bas, Sl1 and 2, Chd
Clear >Ent
Track data clear
Track
E-58
–24 to +24
Pattern, Part
Selects a pattern and/or part inside a track.
Pattern
Clears all patterns.
Set
Clears all track (set) data.
Pattern: 01 to 16
Part: Drm1 to 5, Bass, Sol1 and 2,
Chrd, Ctl1 to 4
Using the Step Sequencer
4. Use the bq cursor (U, q, w, I) buttons to
move the brackets % or the cursor to the item
whose setting you want to change, and then
use the
minus (–) and plus (+) buttons to
change the selected setting.
bq
bl
• Use
PATTERN to change the pattern number.
• Use the
PART minus (–) and plus (+) buttons to
change the part name.
• Use
STEP minus (–) and plus (+) buttons to
change the step number.
• To return to the previous menu level, press
EXIT.
• The mixer screen shows current settings.
• While the Step Edit screen is displayed, the keyboard
will sound the tone of the currently selected part. The
mixer screen shows the settings of each step (the note,
velocity or value item that is currently being changed).
• On the mixer screen, notes are shown in a specific
position on the screen as C through B, regardless of the
actual octave.
9
bk
bq
4. Use the bq cursor (U, q, w, I) buttons to
move the item selection cursor (0) to the item
you want and then press
ENTER. The items
available on the screen are described below.
bq
■ Copy: Copies settings from another slider.
bq
Use the
cursor (U, q, w, I) buttons to move the
brackets % to an item and then use the
minus (–) and
plus (+) buttons to change the item’s setting.
bq
FUNC A/B button setting
Copy source sequence number
Pattern
Copy destination pattern name
FUNC A/B button setting
Changing Slider Settings
In addition to the changes you can make using the simple
editing procedures (page E-51), you can also do the following.
• Copy settings from another slider
• Scale, drum, velocity slider presets
• Note shift
To copy slider settings from another slider
1. Press 1 STEP SEQUENCER.
• Chord parts can be copied between chord parts only.
• Data being edited (!TEMP) can be specified as a copy
source.
■ Preset: Scale, drum, velocity slider presets
bq
Use the
cursor (U, q, w, I) buttons to move the
brackets [ ] to an item and then use the
minus (–) and
plus (+) buttons to change the item’s setting. Inputting a
slider preset number automatically causes the slide preset
name to change accordingly.
bq
Slider preset number
Slider preset name
2. Hold down 2 FUNC A/B until a screen like the
one shown below appears on the display.
Pattern name
3. Press bq MENU.
FUNC A/B button setting
• The following shows the slider preset numbers and their
corresponding slider preset names.
1 Major, 2 Minor, 3 Dorian, 4 Lydian,
5 Mixolydn (Mixolydian), 6 Phrygian, 7 Locrian,
8 M.Minor (Melodic Minor), 9 H.Minor (Harmonic Minor),
10 H.M. 5th (Harmonic Minor 5th), 11 Altered (Altered),
12 WholeTon (Whole Tone), 13 Diminish (Diminished),
14 Pentaton (Pentatonic), 15 M.Penta (Minor Pentatonic),
16 Blues, 17 Kick (Bass Drum), 18 Snare, 19 Hi-hat,
20 Toms, 21 Cymbal, 22 Velocity
• The following are the chord part only slider preset numbers
and their slider preset names.
1 Diatonic, 2 Minor, 3 H.Minor (Harmonic Minor), 4 Velocity
E-59
Using the Step Sequencer
3. Use the bq cursor (U, q, w, I) buttons to
■ Note Shift: Shifts notes.
bq
Use the
cursor (U, q, w, I) buttons to move the
brackets [ ] to an item and then use the
minus (–) and
plus (+) buttons to change the item’s shift value setting.
bq
move the cursor to an item and then input the
setting you want.
Chain number
Measure
Shift value (–24 to +24)
Sequence number
Pattern name
FUNC A/B button setting
Chain type
Key shift
Pattern number
To save an edited sequence
7
Press
WRITE to display the screen for saving a sequence.
Save the sequence by performing the same operation as that
for saving a user tone (page E-12).
• For information about deleting data you saved, see page
E-71.
■ Saving Sequences to an External Device
• Memory card (page E-73)
• Computer (page E-79)
Chaining
To create a chain
1. In the Step Sequencer Mode, press bk CHAIN.
• Button operations to change a setting depend on the
item that is selected.
Sequence number: To select a sequence, perform the
same operation steps 3 through 6
for selecting a tone (page E-20).
Pattern number :
(–, +) or
PATTERN
(–, +)
Measure
:
(–, +) or keyboard key (leftmost
Key shift
:
keys, one octave from C to B)
Chain type
:
(–, +)
• For the chain type, you can specify LOOP, which loops
playback, or END to end chain playback.
• You can use
DELETE to delete part of a chain.
• You also can insert part of a chain by pressing
INSERT.
• To check the currently selected pattern, press
CHAIN and the press
START/STOP to play the
pattern. You can edit a pattern as it is playing.
bq
bq
bq
bl
bq
bk
bk
bk
bk
4. Press 7 WRITE to display the screen for
saving a chain. Save the chain by performing
the same operation as that for saving a user
tone (page E-12).
• For information about deleting data you saved, see
page E-71.
2. Press 7 EDIT.
E-60
■ Saving a Chain to an External Device
• Memory card (page E-73)
• Computer (page E-79)
Using the Step Sequencer
To play back a chain
1. Hold down bk CHAIN until the CHAIN screen
appears.
2. Use the bo dial, bp buttons, or the bq minus
(–) and plus (+) buttons to display the chain you
want to play.
To save a chain in SMF format to a memory
card
• Before performing the following procedure, insert a memory
card into the Synthesizer.
1. Hold down bk CHAIN until the CHAIN screen
appears.
2. Use the bo dial, bp buttons, or the bq minus
(–) and plus (+) buttons to display the chain you
want to save.
3. Press bq MENU.
4. Use the bo dial or bq cursor (U, q, w, I)
buttons to move the item selection cursor (0)
to “SMF Save” and then press
ENTER.
bq
3. Press bk START/STOP.
bk
• To stop playback, press
START/STOP again.
• You can rearrange a chain later, if you want. For details
about how, see “To create a chain” on page E-60.
To initialize chain settings
1. Hold down bk CHAIN until the CHAIN screen
appears.
2. Press bq MENU.
3. Use the bo dial or bq cursor (U, q, w, I)
buttons to move the item selection cursor (0)
to “Initialize” and then press
ENTER.
bq
• For the remainder procedure, perform the steps starting
from step 4 under “Saving Synthesizer Data to a
Memory Card” (page E-75)
• To save data to a memory card, see “Using a Memory
Card” on page E-73.
4. Press bq ENTER again.
This should cause “Sure?” to appear on the display.
5. Press bq YES.
The message “Complete!” will appear on the display when
initialization is complete.
E-61
Using the Performance Mode
7 8
3
bq
2
9
2. Select a performance bank and number the
Overview
same procedures as those for selecting a tone.
You can use the Performance Mode to perform with up to four
tones assigned to the keyboard. In addition to tone
assignments, you can also save effect, Step Sequencer, and
other settings as a setup (called a “performance”) which can
be recalled at any time, even while you are playing, to
instantly change the sequencer’s setup.
• There are 100 preset performances. You can edit preset
performances and save it as one of 100 user performances.
See the separate “Appendix” for a list of preset
performances.
Registering and Recalling
Performances
Zone 1 to 4 on/off and keyboard range settings
using the same procedures as those used when
selecting a tone.
• For details about editing, see “Editable Performance
Parameter List” on page E-64.
1. Press 7 PERFORM.
The button will light and the Synthesizer will enter the
Performance Mode.
bq
This will display the top screen of the performance editing
list.
4. Select items and change settings on the screen
To register a performance
up (q) / down (w)
Use
to select a zone to edit
(page E-64).
3. Press 7 EDIT.
Zone 1 to 4 on/off and
keyboard range setting
screen (page E-64)
5. After you finish with your edits, press 7 EDIT.
This exits the editing list.
6. Press 7 WRITE and then save your edited
performance as a user performance.
• For information about how to save user data, see the
procedure for saving user tone data (page E-12).
■ Saving User Performance Data to an External
Device
• Memory card (page E-73)
• Computer (page E-79)
bq
Press
left (U) to advance to
the screen below.
E-62
3 K1 to K4 knob functions
(page E-64)
Using the Performance Mode
To recall a performance
1. Press 7 PERFORM.
The button will light and the Synthesizer will enter the Performance Mode.
2. Select a performance bank and number the same procedures as those for selecting a tone.
This will recall the contents of the performance you selected.
• Recalled performance contents are the same as those described in “Editable Performance Parameter List” in the next
section of this manual.
• Here you can configure a performance filter to omit certain settings (Sequencer, arpeggio, etc.) contained in recalled
performance data. Press
MENU to display the performance menu. Next, select “PrfrmFilter >Ent” shown below to enter
the group and configure performance filer settings.
bq
Performance Filter Setting List
Display
PrfrmFilter >Ent
Description
Settings
Performance filter
Step Seq
Step Sequencer on/off. Turning on this setting filters out Step Sequencer items contained in the
Sequencer Parameter group of the Editable Performance Parameter List (page E-64).
Off, On
Arpeggio
Arpeggio on/off. Turning on this setting filters out Arpeggio items contained in the Sequencer
Parameter group of the Editable Performance Parameter List (page E-64).
Off, On
Phrase
Phrase on/off. Turning on this setting filters out Phrase Sequencer items contained in the
Sequencer Parameter group of the Editable Performance Parameter List (page E-64).
Off, On
Tempo
Tempo on/off. Turning on this setting filters out Tempo settings contained in the Sequencer
Parameter group of the Editable Performance Parameter List (page E-64).
Off, On
Sys Rev
System reverb. Turning on this setting filters out reverb items contained in the Effect Parameter
group of the Editable Performance Parameter List (page E-64).
Off, On
Sys Cho
System chorus. Turning on this setting filters out chorus items contained in the Effect Parameter
Off, On
group of the Editable Performance Parameter List (page E-64).
Master EQ
Master Equalizer (Master EQ). Turning on this setting filters out master equalizer items contained
Off, On
in the Effect Parameter group of the Editable Performance Parameter List (page E-64).
E-63
Using the Performance Mode
Editable Performance Parameter List
Editable Parameter List
Display
Zone Parame >Ent
Description
Settings
Zone parameters. This group includes parameters for each of the zones (Zone 1 through 4).
• Use the
PART minus (–), plus (+) buttons to select the zone you want to edit.
• You also can enter the group using the following shortcut: Perform step 2 under “To register a
performance” (page E-62) and then hold down
EDIT. This will enter the group.
9
7
Zone
Zone on/off. Turns all zones on or off This setting is different from the mixer function page (page
Off, On
E-68) part on/off (Part Enable) setting.
Tone
Tone. Selects the tone for each zone. This setting is the same as the mixer function part tone
(page E-68).
• While this item is selected, you can select a tone using the same operation as that used in the
Tone Mode.
• This setting can also be configured using quick editing (page E-16).
• There are some limitations on the selection of tone categories for Zones 2 through 4 (page
E-16).
• A tone with DSP will have DSP next to the tone name on the display (page E-37).
Zone 1:
Solo Synth P00 to
Various U29
Zone 2 to 4:
Piano P00 to
Various U29
Key range low. Specifies the low key range of the keyboard for each zone. This setting is used in
combination with the Key Range Hi setting to configure key ranges for each zone.
For example, configuring F3 (low) to C7 (high) for Zones 1 and 2 and C2 (low) to E3 (high) for
Zones 3 and 4 will enable play of Zone 1 and 2 tones on the right side keyboard range in the
illustration below, and the Zone 3 and 4 tones on the left side keyboard.
Zone 3
Zone 4
KeyRangLow
C2
Zone 1
Zone 2
E3 F3
C-1 to G9
C7
• Setting can be specified using the keyboard keys.
KeyRangHi
Key range high. Specifies the high range of the keyboard for each zone. This setting is used in
combination with the Key Range Lo setting to configure key ranges for each zone.
C-1 to G9
Volume
Volume. This setting is the same as the mixer function tone volume (page E-68).
0 to 127
Pan
Pan. Adjusts the left-right position of sound in the stereo field. This setting is the same as the
mixer function part panning (page E-68).
–64 to 0 to +63
Oct.Shift
Octave shift. Shifts the tone of notes by octave units.
–2 to 0 to +2
Transpose
Transpose. Shifts the tone of notes by semitone units. This setting is the same as the mixer
function part coarse tune (page E-68).
–12 to 0 to +12
FineTune
Fine tune. This setting is the same as the mixer function part fine tune (page E-68).
–99 to 0 to +99
BendRngDwn
Bend range down. Pitch change amount for downward bender operation.
0 to 24
BendRngUp
Bend range up. Pitch change amount for upward bender operation.
0 to 24
Rev Send
Reverb send. This setting is the same as the mixer reverb send (page E-68).
0 to 127
Cho Send
Chorus send. This setting is the same as the mixer chorus send (page E-68).
0 to 127
DSP Line
DSP line. This setting is the same as the mixer function part DSP line (page E-68).
Off, On
Knob1Enable
3
3 K2 operation for each zone.
Knob 3 on/off. Enables/disables 3 K3 operation for each zone.
Knob 4 on/off. Enables/disables 3 K4 operation for each zone.
Bender on/off. Enables/disables bs BENDER operation for each zone.
Modulation wheel on/off. Enables/disables bs MODULATION operation for each zone.
Pedal on/off. Enables/disables operation of a pedal plugged in to the ck SUSTAIN/
Off, On
Knob2Enable
Knob3Enable
Knob4Enable
Bend Enable
Wheel Enable
Pedal Enable
E-64
Knob 1 on/off. Enables/disables
K1 operation for each zone.
Knob 2 on/off. Enables/disables
ASSIGNABLE JACK for each Zone.
Off, On
Off, On
Off, On
Off, On
Off, On
Off, On
Using the Performance Mode
Display
Description
Settings
Arp Enable
Arpeggio on/off. Enables/disables arpeggio function (page E-40) for each zone.
Off, On
Phrase Enable
Phrase on/off. Enables/disables the Phrase Sequencer (page E-44) for each zone.
Off, On
Controller >Ent
Controller parameters. This is group of editable controller parameters.
3
Knob Target 1. Selects the parameter controlled by
K1 knob operation. For example, if
“CC67:Soft” is specified for this setting,
K1 operation will apply a soft pedal effect.
3
K1
CC00 to CC97: MIDI control change*1
NRPN, RPN: MIDI NRPN and RPN parameters*1 *2
Ch Pressure: MIDI channel pressure*1
Arpeggio: Preset arpeggio type (page E-40)
Tempo: Tempo setting (page E-45)
EQ Low Gain - EQ High Gain: Master EQ >Low Gain - High Gain (page E-38)
Refer to the cell to
the left.
*1 For details about each setting, refer to the MIDI Implementation document
(http://world.casio.com/) and other MIDI documentation.
*2 After selecting these parameters, press
ENTER again and then adjust the items below.
MSB: 63H for NRPN, 65H for RPN (Setting range: 000 to 127)
LSB: 62H for NRPN, 64H for RPN (Setting range: 000 to 127)
Send Data: Specifies whether knob operation controls MSB or LSB. (Settings: MSB, LSB)
bq
K2 to K4
Knob Target 2 to Knob Target 4. As with K1 (Knob Target 1), Selects the parameter controlled by
Same as K1.
K2 to K4 knob operation.
3
Pedal. Specifies the function of the pedal plugged in to
Pedal
ck SUSTAIN/ASSIGNABLE JACK.
Hold: Pressing the pedal sustains notes. This is a sustain effect.
Soft: Pressing the pedal slightly lowers the volume of notes.
Sostenuto (Sostenut): Pressing the pedal while keyboard keys are depressed sustains (holds)
only the notes of the pressed keyboard keys.
Refer to the cell to
Step Sequencer Play/Stop (SSEQ P/S): Pressing the pedal starts or stops Step Sequencer
the left.
sequence playback.
Phrase Sequencer Play/Stop (Phrase P/S): Pressing the pedal starts or stops Phrase Sequencer
phrase playback.
Phrase Record (Phrase REC): Same function as the Phrase Sequencer
REC button.
Rotary Slow/Fast (Rotary S/F): Pressing the pedal performs the same operation as drawbar
organ tone
SLOW/FAST. This changes the speed of rotary speaker rotation.
bn
2
Touch. Specifies touch sensitivity when the keyboard is played.
Touch
TchOffVel
Sequencers >Ent
Tempo
Off (Off): Notes sound at a fixed volume level regardless of keyboard pressure.
Normal
Light: High-volume notes are easily produced even with light keyboard pressure.
Touch off velocity. Specifies the volume level at which the above touch curve setting values
become off.
Refer to the cell to
the left.
0 to 127
Sequencers parameter. This group includes Step Sequencer (page E-49), Phrase Sequencer
(page E-44), and Arpeggio function (page E-40).
Tempo. Adjusts the Phrase Sequencer and Step Sequencer playback tempo. You also can
TEMPO.
change the playback tempo using
8
Step SEQ Number Step sequencer number. Specifies the Step Sequencer sequence (page E-51).
30 to 255
Preset00 to
User99
Solo1 Ch
Step Sequencer solo track part. Step Sequencer Solo Track 1 is normally Part 14, but it can be
changed to Part 1 (Zone Part 1, page E-54).
1, 14
Change
Step Sequencer change timing. Specifies the switching timing when a pattern is changed by the
Step Sequencer (page E-55).
Wait, Real
Key Shift
Step Sequencer key shift Switches the Step Sequencer key shift function between on and off
(page E-51).
Off, On
Pattern
Step sequencer pattern number. Selects the step sequencer pattern (page E-49).
1 to 8
Arp On/Off
Arpeggio on/off. The arpeggio function is disabled while this setting is off.
Off, On
Arp Type
Arpeggio type. Specifies the arpeggio type (page E-40).
Preset00 to
User99
ArpKeyRgLo
Arpeggio key range low. Specifies the low keyboard range where the arpeggio function is
enabled. This setting is used in combination with the Arpeggio Key Range Hi setting to configure C-1 to G9
the keyboard range where the arpeggio function is enabled.
E-65
Using the Performance Mode
Display
ArpKeyRgHi
Description
Settings
Arpeggio key range high. Specifies the high keyboard range where the arpeggio function is
enabled. This setting is used in combination with the Arpeggio Key Range Lo setting to configure C-1 to G9
the keyboard range where the arpeggio function is enabled.
Arp Hold
Arpeggio hold on/off. Enables/disables arpeggio hold (page E-40).
Off, On
Arp Synchro
Arpeggio synchronization. Switches the arpeggio sync setting (page E-40).
Off, On, S/S
Key Play
Phrase key play. Turns Phrase Sequencer Phrase key play on or off.
Off, On
Phrase
Phrase number. Selects the phrase of the Phrase Sequencer (page E-44).
Preset00 to
User99
PhrKeyRgLo
Phrase key range low. Specifies the low keyboard range where Phrase Sequencer key play is
effective (page E-45). This setting is used in combination with the Phrase Key Range Hi setting to C-1 to G9
specify the keyboard range where key play is enabled.
PhrKeyRgHi
Phrase key range high. Specifies the effective high keyboard range where Phrase Sequencer key
play is effective (page E-45). This setting is used in combination with the Phrase Key Range Lo C-1 to G9
setting to specify the keyboard range where key play is enabled.
Effect >Ent
Effect parameter. This group includes effect settings (page E-38). For details about group items,
see “Effect Settings” (page E-38).
MIDI >Ent
MIDI parameters. This group includes MIDI parameter (page E-70) settings. Use the
PART
minus (–), plus (+) buttons to select one of the Synthesizer’s 16 sound source parts for editing.
E-66
9
Ext Out Ch
External Out Channel. Specifies the MIDI send channel for sending information about each part
to an external destination.
1 to 16
Ext In Ch
External in channel. This is the MIDI message channel received by each part.
Off, 1 to 16
Gen Out
Internal send on/off. Specifies whether or not the information of each part is sent to the
Synthesizer’s sound source.
Off, On
MIDI Out
MIDI output on/off. Specifies whether or not MIDI send of the information of each part is
performed from
MIDI OUT/THRU.
Off, On
USB Out
USB output on/off. Specifies whether or not MIDI send of the information of each part is
performed from
USB.
Off, On
bt
bt
Other Useful Functions
bm
7
bo
bq
4
2
5
9
bk
3. Use the bq cursor (U, q, w, I) buttons to
Using the Mixer
The mixer lets you make adjustments to the tone, volume
level, and other settings* of the Synthesizer’s sound source
parts (Parts 01 through 16, external input parts, page E-18),
while viewing the balance between the parts on the display.
* Settings that affect individual parts are called “part
settings”, wile settings that affect all parts are called
“master settings”.
1. Press bm MIXER.
This displays the mixer screen.
Part being configured
Current part setting
bo
select the item you want, and then use the
dial or
minus (–) and plus (+) buttons to
change its setting.
bq
• For details about settings, see “Mixer Settings” on page
E-68
4. After settings are the way you want, press bm
MIXER to exit the mixer screen.
Instant Adjustment of Settings using the
Sliders and Step Buttons
5
4
You can use the
1/9 to MASTER sliders and the
step
(1 to 16) buttons to make instant changes in mixer settings.
1. Press bm MIXER.
This displays the mixer screen.
Setting item list
Indicates part being configured
2. Use the 9 PART minus (–) and plus (+) buttons
2. Use the 2 KEY SHIFT, FUNC A/B, and 1-8/9-16
buttons to change the part assigned to the
1/9 to MASTER sliders.
• Each press of one of the above buttons toggles the
button between being lit and unlit.
to select the part whose settings you want to
configure.
To perform this
adjustment:
Individual settings (page
E-68) of parts 01 through
16
Master
Ext
Unlit
Lit
Select this part:
All, 01 to 16
• “All” can be selected to batch adjust all
parts from 01 through 16. To select
PART minus (–)
“All”, press the
button once while “01” is displayed.
9
Master settings (page
E-68)
Master
• To select “Master”, press the
PART minus (–) button twice while
“01” is displayed.
External input part
settings (page E-68)
Ext
PART
• To select “Ext”, press the
minus (–) button three times while
“01” is displayed.
5
Unlit
Lit
Part 01 - 08
Part 09 - 16
2
9
9
Unlit
Lit
Part 01 through 08 (or 09 through 16)
All parts (leftmost slider only)
E-67
Other Useful Functions
3. Move a slider to adjust the setting of the part assigned to it.
• Use the
bq cursor (U, q, w, I) buttons to select a setting item.
4. Use the 4 1 to 16 buttons to toggle parts 01 through 16 between on and off.
• Each press of a button toggles it between lit (on) and unlit (off).
• Holding a button down will turn that part on and turn all other parts off (solo mode). Press the same button again to exit the
solo mode.
Example: To enter the solo mode for Part 08
Lit
4
Hold down for a short while.
Mixer Settings
■ Part 01 through Part 16 Settings
Display
Description
Settings
4
Part
Part on/off. Turns each part on or off. This is the same parameter that is turned on and off by the
1 to 16 buttons (page E-68).
Tone
Part tone. This is the tone of each part.
While this item is selected, you can select a tone using the same operation as that used in the Tone
Mode.
• A tone with DSP will have DSP next to the tone name on the display (page E-37).
Part 01: Solo Synth
P00 to Various U29
Part 02 to 16: Piano
P00 to Various U29
Volume
Part volume. This is the volume of each part.
0 to 127
Pan
Part panning. Adjusts the left-right position of sound in the stereo field.
–64 to 0 to +63
CoarseTune
Part coarse tune. Shifts the pitch of notes by semitone units.
–12 to 0 to +12
FineTune
Part fine tune. Shifts the pitch of notes by cent units.
–99 to 0 to +99
BendRange
Part bend range. Specifies (in semitone units) the maximum change in pitch when the
wheel is rotated.
DSP Line
Part DSP line. Specifies whether DSP (page E-37) is applied to the notes of each part.
Off, On
Rev Send
Part reverb send. Controls how the reverb effect (page E-37) is applied to each part.
0 to 127
Cho Send
Part chorus send. Controls how the chorus effect (page E-37) is applied to each part.
0 to 127
bs BENDER
Off, On
–24 to 0 to +24
■ External Input Part Settings
Display
Description
Settings
Part
Volume
Pan
Same as “Part 01 through Part 16 Settings” (page E-68).
DSP Line
Rev Send
Cho Send
N.Thresh
Noise gate threshold. Reduces noise by cutting all input sound at a volume that is smaller than this
setting value.
0 to 127
N.Release
Noise gate release. Time that input sound is cut after its volume drops below the noise gate threshold
value.
0 to 127
Auto Level
Auto level control. Automatically adjusts the input signal level. The greater the setting value, the stronger
the effect.
Off, 1 to 3
■ Master Settings
Display
Description
Settings
Volume
Master volume. Adjusts the volume of all the parts.
0 to 127
Pan
Master panning. Adjusts the left-right position of sound in the stereo field of all the parts.
–64 to 0 to +63
E-68
Other Useful Functions
Setting Item
Global Synthesizer Settings
Display
The following are Synthesizer settings that can be configured
globally.
• Tuning (Fine tuning of note pitch)
• Local Control
• Master Coarse Tune (Tuning of note pitch in semitone
steps)
• Initial Power On Mode
• Display Contrast
• Auto Power Off On/Off (page E-10)
1. Press 7 SETTING.
Settings
Tuning
415.5 to
465.9Hz
M.Coarse
Master coarse tune. Adjustment of
overall Synthesizer pitch in semitone
units
–24 to 0 to
+24
Local Ctrl
Local control. Turning off local
control disables the Synthesizer’s
internal sound source, so nothing
sound when keyboard keys are
pressed. Turn off local control when
you want to use the Synthesizer
keyboard and pedal operations to
operate an external sound source,
without producing any sound from
the Synthesizer itself.
Off, On
Start Up
Start up item. Specifies one of the
following as the Synthesizers initial
power on mode.
Perfm: Performance Mode
Tone: Tone Mode
S.Seq: Step Sequencer Mode
Refer to the
cell to the
left.
Contrast
Display contrast. Adjusts the
contrast of the display.
1 to 17
Auto Power
Auto Power Off function on/off.
Turning off this setting disables Auto
Power Off (page E-10).
Off, On
This displays the setting screen with “General >Ent”
selected.
2. Press bq ENTER.
Description
Tuning. Fine tuning of Synthesizer
pitch in 0.1 Hertz steps.
4. After settings are the way you want, press 7
SETTING to exit the setting screen.
Using MIDI
What is MIDI?
3. Use the bq cursor (U, q, w, I) buttons to
bo
select the item you want, and then use the
dial or
minus (–) and plus (+) buttons to
change its setting.
bq
The letters MIDI stand for Musical Instrument Digital Interface,
which is the name of a worldwide standard for digital signals
and connectors that makes it possible to exchange musical
data between musical instruments and computers (machines)
produced by different manufacturers.
For details about the MIDI specifications of this Synthesizer,
see the “MIDI Implementation” document at the website
located at the URL below.
http://world.casio.com/
• Use a separately available or commercially available MIDI
cable to connect the MIDI terminals of your Synthesizer and
another electronic musical instrument for exchange of MIDI
data (page E-8).
• For information about connecting a computer, see page
E-79.
• For information about the relationship between each
Synthesizer part (page E-67) and the MIDI IN and MIDI
OUT channels, see “Editable Performance Parameter List”
(page E-64).
• This Synthesizer conforms to General MIDI Level 1 (GM).
E-69
Other Useful Functions
MIDI Settings
Display
“MIDI >Ent” and then press
Off, On
S.Seq NRPN
Step Sequencer NRPN change.
When this setting is turned on, a
Synthesizer sequence (page E-51)
can be selected by a MIDI NRPN
message from an external device.
Off, On
Phrase NRPN
Phrase NRPN change. When this
setting is turned on, a Synthesizer
phrase (page E-44) can be selected
by a MIDI NRPN message from an
external device.
Off, On
Arp NRPN
Arpeggio NRPN change. When this
setting is turned on, a Synthesizer
arpeggio type (page E-40) can be
selected by a MIDI NRPN message
from an external device.
Off, On
bq ENTER.
3. Use the bq cursor (U, q, w, I) buttons to
bo
select the item you want, and then use the
dial or
minus (–) and plus (+) buttons to
change its setting.
bq
Setting Item
Display
Description
Settings
Device ID. Selects the ID number of
the Synthesizer for MIDI system
exclusive message send/receive.
• While “All” is selected, a system
exclusive message is sent
regardless of the ID number.
• For details about the ID number,
see MIDI Implementation at
http://world.casio.com/.
1 to 16, ALL
Basic Ch
Basic channel. Specifies the receive
channel of “Perform NRPN”, “S.Seq
NRPN”, and other MIDI messages
described below.
1 to 16
MIDIOutSel
MIDI OUT select. Specifies what is
output as MIDI OUT.*
KEY (Keyboard): Synthesizer
keyboard play, operations, etc.
MIDI (MIDI IN): Messages input via
MIDI IN (MIDI THRU)
USB (USB IN): Messages input via
USB
Refer to the
cell to the
left.
USB out select. Specifies what is
output as USB out.*
KEY (Keyboard): Keyboard and
other Synthesizer operations.
MIDI (MIDI IN): Messages input via
MIDI IN
Refer to the
cell to the
left.
MIDI In
MIDI IN on/off (MIDI IN enable).
While this setting is turned on,
MIDI IN are
messages input via
reflected by the Synthesizer’s
internal sound source.
Off, On
USB In
USB IN on/off (USB IN enable).
While this setting is turned on,
USB are
messages input via
reflected by the Synthesizer’s
internal sound source.
Off, On
Sync Mode
Sync mode. Settings for MIDI
syncing between the Synthesizer
and an external device.*
Off: No syncing
Mast (Master): Outputs Clock, Start/
Stop (Step Sequencer), and other
signals from the Sequencer to
control an external device.
Slav (Slave): Receives Clock, Start/
Stop, and other signals from an
external device.
• Step Sequencer and Phrase
Sequencer playback is not
possible unless Clock is received.
Start/Stop is interpreted as Step
Sequencer start/stop.
Refer to the
cell to the
left.
Device ID
bt
bt
USBOutSel
* To apply setting changes, turn the Synthesizer off and then
back on again. A message to that effect appears on the
display whenever you exit a setting screen.
4. After settings are the way you want, press 7
bt
E-70
bt
bt
Settings
Perform NRPN
1. Press 7 SETTING.
2. Use the bq down (w) button to select
Description
Performance NRPN change.
When this setting is turned on, a
Synthesizer performance (page
E-63) can be selected by a MIDI
NRPN message from an external
device.
SETTING to exit the setting screen.
• You can also use performance data editing to change the
MIDI data send channel and configure other settings. For
more information, see the “MIDI >Ent” group (page E-66).
Other Useful Functions
Deleting Data Saved on the
Synthesizer
Initializing Synthesizer Global
Settings and Data
Use the procedure below to delete user tones, user
sequences, and other data that you created, and return
memory to its initial factory default status.
You can use the procedure below to initialize Synthesizer
global settings and data, and return them to their initial factory
defaults.
1. Referring to the table in step 2 of the procedure
1. Press 7 SETTING.
under “To save Synthesizer data to a memory
card” (page E-75), perform the procedure
required for the type of data you want to delete.
2. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to “Clear
USER” and then press
ENTER.
bq
2. Press bq ENTER.
3. Use the bq cursor (U, q, w, I) buttons to
select “Initialize >Ent” and then press
(ENTER).
bq
This will display the INITIALIZE screen.
• This causes a menu screen like the one shown below
to appear on the display. The sample screen below
shows the screen that appears when you perform this
procedure from the Step Sequencer Mode.
4. Use the bq up (q) and down (w) buttons to
select the initialization option you want.
• In the case of the Phrase Sequencer, the phrase data
size is also displayed.
3. Use the bo dial or bq minus (–) and plus (+)
buttons to select the user data you want to
delete.
4. Press the bq ENTER button.
5. In response to the “Sure?” message that
bq
appears, press the
YES button to delete or
the
NO button to cancel.
bq
Initialization Options
Display
Description
Parameter >Ent
Parameters only. Initializes all Synthesizer
settings except for display contrast (E-69).
All >Ent
All settings and data. Initializes all Synthesizer
global settings and data, and return them to their
initial factory defaults.
5. Press bq ENTER.
This should cause “Sure?” to appear on the display.
6. Press bq YES.
The message “Complete!” will appear on the display when
delete is complete.
7. Press 7 SETTING to exit the setting screen.
E-71
Other Useful Functions
Playing a Demo Tune or a File
from a Memory Card
You can use the procedure below to play back the
Synthesizer built in demo tunes, and to play back SMF
(Standard MIDI File) music files or audio files stored on a
memory card.
1. Press 7 SETTING and 7 WRITE at the same
time.
This will enter the Playback Mode.
3. Press bq ENTER.
This displays the playback screen.
• In the case of a demo tune, playback will start
automatically. In the case of an SMF music file or an
audio file, use the
minus (–) and plus (+) buttons
to select a file and press
START/STOP to start
playback.
• While playback is in progress, you can use the
dial
or
minus (–) and plus (+) buttons to change to a
different tune or file for playback.
You also can use the four
buttons to perform fast
forward and other playback operations as shown
below.
bq
bk
bo
bq
bk
Demo Tune Playback Screen
Tune name
2. Use the bq up (q) and down (w) buttons to
select the type of playback you want to perform.
Auto Playback Types
Display
Description
Demo >Ent
Demo Tune (Demo). For playback of the
Synthesizer’s built-in demo tunes.
SMF >Ent
SMF (Standard MIDI File) music files. For
playback of SMF music files from a memory card
loaded in the Synthesizer’s card slot.
• Supported playback music files formats are SMF
format 0 and 1 MIDI files (MID).
• Make sure that the data you want to play is in the
MUSICDAT folder (page E-77) on the memory
card.
Audio >Ent
E-72
Audio file. For playback of audio files from a
memory card loaded in the Synthesizer’s card slot.
• Supported playback audio files are those that
have been converted using a computer data
editor (page E-80). For details, refer to the user
documentation that comes with your data editor.
Operation Guide
s (Fast Reverse)
d (Fast Forward)
Y (Stop)
k (Pause)
:
:
:
:
bk STEP –
bk STEP +
bk START/STOP
bk CHAIN
9
• You can use the
PART minus (–) and plus (+)
buttons to adjust the volume of audio playback.
4. Press bk START/STOP.
This stops playback and exits the playback screen.
• You also can stop playback by pressing the
SETTING and WRITE buttons at the same time or by
pressing
EXIT.
7
bq
• Never touch the memory card loaded in the Synthesizer
audio playback is in progress. Doing so can cause
operational problems or file corruption, or it can make
the card unusable due to electrostatic charge.
Using a Memory Card
bm
7
3
bo
bq
bk
You can save Synthesizer user area data to a memory card
and load data from a memory card to Synthesizer memory.
You also can play music files (MIDI files) stored on a memory
card on the Synthesizer.
• Use a memory card that satisfies the
conditions below.
Format: SDHC or SD
Capacity: 32GB or less
Use of any memory cards other than
those defined above is not
supported.
• SDHC Logo is a trademark of SD-3C,
LLC.
Supported Data Types
■ Data that can be saved to and exported from a
memory card
Data Type
Description
(File Name Extension)
User performances
(page E-62)
Performance data edited with the
Synthesizer (ZPF)
User PCM melody tones
(page E-33)
Melody tone data edited with the
Synthesizer (ZTN)
User drawbar organ tones
(page E-32)
Drawbar organ tone data edited with
the Synthesizer (ZDO)
User hex layer tones
(page E-30)
Melody hex layer tone data edited
with the Synthesizer (ZLT)
User Solo Synthesizer tones
(page E-22)
Solo Synthesizer tone data edited
with the Synthesizer (ZSY)
User PCM drum tones
(page E-34)
Drum tone data edited with the
Synthesizer (ZDR)
User DSP data
(page E-39)
DSP data edited with the Synthesizer
(DS7)
User step sequences
(page E-51)
Step sequence data recorded with
the Synthesizer (ZSS)
Step sequence chains
(page E-61)
Sequence chain data recorded with
the Synthesizer (ZSC, MID (save
only))
Data Type
Description
(File Name Extension)
User phrases
(page E-44)
Phrase data recorded with the
Synthesizer (ZPH)
User arpeggios
(page E-41)
Arpeggio data edited with the
Synthesizer (ZAR)
All data
All of the above data (ZAL)
Setting data
Setting data configure with the
Synthesizer (ZST)
• For information about saving and importing individual data
items, see “Saving Synthesizer Data to a Memory Card”
(page E-75) and “Loading Data from a Memory Card” (page
E-77).
• For details about saving and loading all data, see “To batch
save all Synthesizer data to a memory card” (page E-76)
and “To batch load all Synthesizer memory data from a
memory card” (page E-77).
■ Data that can be directly played back from a
memory card
Data Type
Song files
(page E-78)
Description
(File Name Extension)
SMF format 0 or 1 MIDI files (MID)
• If you want to use data stored on a memory card that is not
supported by this Synthesizer, you need either to copy the
data to a memory card supported by the Synthesizer, or
use Data Editor to transfer the data from a computer to the
Synthesizer. For more information, see “Connecting to a
Computer” (page E-79).
E-73
Using a Memory Card
Card and Card Slot Precautions
• Be sure to observe the precautions provided in the
documentation that comes with the memory card.
• Memory cards have a write-protect switch. Use it when you
want to protect the data on the card from accidental
deletion.
• Avoid using a memory card under the following conditions.
Such conditions can corrupt data stored on the memory
card.
– Areas subjected to high temperature, high humidity, or
corrosive gas.
– Areas subjected to strong electrostatic charge and digital
noise.
• Never touch the contacts of a memory card when loading it
or removing it from the Synthesizer.
• The message “Please Wait” will remain on the display while
a data save operation is in progress. Do not perform any
other operation while it is displayed.
Turning off the Synthesizer or removing the memory card
can cause Synthesizer data to be deleted or become
corrupted. It also can cause the Synthesizer to fail to turn
on when
POWER is pressed. If this happens, refer to
“Troubleshooting” (page E-82).
• If the message “No Card” appears on the display, it means
there is no memory card in the card slot. For details about
what appears on the display while a card is loaded, see
“Playing a Music File from a Memory Card” (page E-78).
• Never insert anything besides a memory card into the card
slot. Doing so creates the risk of malfunction.
• Electrostatic charge from your fingers or the memory card
to the card slot can cause malfunction of the Synthesizer. If
this happens, turn the Synthesizer off and then back on
again.
• A memory card can become quite warm after very long use
in the card slot. This is normal and does not indicate
malfunction.
Loading and Removing a Memory
Card
• A memory card must be positioned correctly when
being loaded into the Synthesizer. Trying to force an
improperly oriented memory card into the slot can
damage the memory card and the slot.
1. With the top of the memory card facing
upwards (so you can see it), carefully insert it
into the Synthesizer’s SD card slot ( ) until
stops with a click.
bt
6
E-74
Top
2. To remove the memory card first press it into
the slot further.
• This will cause the memory card to disengage and eject
partially. Pull the memory card the rest of the way out of
the slot.
Using a Memory Card
Formatting a Memory Card
• Format a memory card before using it for the first time.
• Before formatting a memory card, make sure it does
not have any valuable data stored on it.
• The memory card format operation performed by this
Synthesizer is a “quick format”. If you want to
completely delete all of the data on the memory card,
format it on your computer or some other device.
1. Insert the memory card you want to format into
the Synthesizer’s card slot.
• Make sure the memory card is write-enabled. Check
the position of the card’s write-protect switch to ensure
it is not in the write-protect position.
2. Press 7 SETTING.
3. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to
“CardUtility” and then press
ENTER.
Saving Synthesizer Data to a
Memory Card
To save Synthesizer data to a memory card
1. Insert the memory card into the card slot.
2. Depending on the type of data you want to save
to the memory card, perform one of the steps
shown below.
To save this
type of data:
One user
performance
One user PCM
melody tone
4. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to “Format”.
7 PERFORM.
bq MENU.
1. Press 7 TONE.
2. Press one of the bl PIANO to VARIOUS
1. Press
2. Press
buttons to select a melody tone.
3. Press
MENU.
One user drawbar
organ tone.
bq
• This causes the “CARD UTIL” screen to appear.
Perform these steps:
One user hex layer
tones
One user Solo
Synthesizer tone
One user PCM
drum tone
bq
7 TONE.
bl DRAWBAR ORGAN.
bq MENU.
1. Press 7 TONE.
2. Press bl HEX LAYER.
3. Press bq MENU.
1. Press 7 TONE.
2. Press bl SOLO SYNTH.
3. Press bq MENU.
1. Press 7 TONE.
2. Press bl VARIOUS and then select the
1. Press
2. Press
3. Press
drum tone.
3. Press
MENU.
bq
One user DSP
bm
MIXER until the EFFECT
1. Hold down
screen appears on the display.
2. Use the
cursor (U, q, w, I) buttons
to move the item selection cursor (0) to
“DSP Select” and then press
ENTER.
• “Ent” is not displayed in the case of a Solo
Synthesizer tone.
3. Press
MENU.
bq
bq
5. Press the bq ENTER button.
• This will cause the confirmation message “Sure?” to
appear.
6. Press the bq YES button to format the memory
card or the
bq NO button to cancel.
• The message “Please Wait” will remain on the display
while the format operation is being performed. Do not
perform any Synthesizer operation while this message
is on the display. “Complete!” appears on the display
after formatting is complete.
• Formatting may take as long as a few minutes to
complete.
One user step
sequence
One step
sequence chain
bq
7 STEP SEQ.
bq MENU.
1. Hold down bk CHAIN until the CHAIN
1. Press
2. Press
screen appears on the display.
2. Press
MENU.
bq
bn
One user phrase
KEY PLAY until the PHRASE
1. Hold down
screen appears on the display.
2. Press
MENU.
One user arpeggio
ARPEGGIO until the
1. Hold down
ARPEGGIO screen appears on the display.
2. Press
MENU.
All data
SETTING.
1. Press
2. Use the
up (q) and down (w)
buttons to move the item selection cursor
(0) to “CardUtility” and then press
ENTER.
3. Use the
up (q) and down (w)
buttons to move the item selection cursor
(0) to “All data” and then press
ENTER.
bq
bm
bq
7
bq
bq
bq
bq
E-75
Using a Memory Card
5. Select the bank and memory location number,
To save this
type of data:
Setting data
Perform these steps:
7
bq
1. Press
SETTING.
2. Use the
up (q) and down (w)
buttons to move the item selection cursor
(0) to “CardUtility” and then press
ENTER.
3. Use the
up (q) and down (w)
buttons to move the item selection cursor
(0) to “SettingData” and then press
ENTER.
bq
bq
bq
3. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to “Card
Save” (or “Save” if you want to save all data)
and then press
ENTER.
bq
• This displays a screen like the one shown below. (As
an example, the remainder of this procedure uses the
screen that appears when you perform these steps
from the Performance Mode.)
and input a file name. You can perform the
following steps to change the initial default file
name that is assigned automatically.
bq
(1) Use the
cursor (U, I) buttons to move the cursor
to the character you want to change.
(2) Use the
dial or
minus (–) and plus (+)
buttons to change the character.
• For details about inputting characters, see “Creating
Tones” on page E-12.
• The characters you can select are shown below.
bo
0
A
K
U
(
1 2 3
B C D
L M N
V W X
) - ^
bq
4
E
O
Y
{
5 6
F G
P Q
Z S
} @
7
H
R
&
~
8
I
S
_
`
9
J
T
'
• The three characters at the end of a file name are a file
name extension, which indicates the type of data stored
in the file.
6. After everything is the way you want, press the
bq (ENTER) button.
7. In response to the “Sure?” message that
4. Press bq ENTER.
bq
appears, press the
YES button to save or
the
NO button to cancel.
bq
To batch save all Synthesizer data to a
memory card
1. Press 7 SETTING.
2. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to
“CardUtility” and then press
ENTER.
bq
• This causes the “CARD UTIL” screen to appear.
3. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to “ALL
Data” and then press
ENTER.
bq
E-76
Using a Memory Card
4. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to “Save”.
3. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to “Card
Load” (or “Load” if you want to load all data)
and then press
ENTER.
bq
• This causes a menu screen like the one shown below
to appear on the display. The sample screen below
shows the screen that appears when you perform this
procedure from the Step Sequencer Mode.
• The remainder of the steps are the same as those from
step 3 under “To save Synthesizer data to a memory
card” (page E-75).
■ Memory card Data Storage
The above procedure stores Synthesizer data in a folder
named MUSICDAT on the memory card.
• The MUSICDAT folder is created automatically when you
format the memory card on the Synthesizer (page E-75).
• Note that files not in the MUSICDAT folder cannot be
loaded, deleted, or renamed by this Synthesizer. You also
will not be able to load or delete any file stored in any
subfolder inside the MUSICDAT folder.
Loading Data from a Memory
Card
4. Use the bo dial or bq minus (–) and plus (+)
buttons to display the file you want to import.
5. Use the bq down (w) button to move the
cursor downwards, and then use the bo dial or
bq minus (–) and plus (+) buttons to display the
destination of the load operation.
6. Press the bq ENTER button.
7. In response to the “Sure?” message that
• Make sure that all of the data you want to load is in the
MUSICDAT folder on the memory card.
To load data to Synthesizer memory from a
memory card
bq
appears, press the
YES button to load or the
NO button to cancel.
bq
To batch load all Synthesizer memory data
from a memory card
1. Insert the memory card into the card slot.
1. Press 7 SETTING.
2. Referring to the table in step 2 of the procedure
2. Use the bq up (q) and down (w) buttons to
under “To save Synthesizer data to a memory
card” (page E-75), perform the procedure
required for the type of data you want to load
from the card.
move the item selection cursor (0) to
“CardUtility” and then press
ENTER.
bq
• This causes the “CARD UTIL” screen to appear.
3. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to “All
Data” and then press
ENTER.
bq
• The remainder of the steps are the same as those from
step 3 under “To load data to Synthesizer memory from
a memory card” (page E-77).
E-77
Using a Memory Card
To delete a file from a memory
card
To rename a file on a memory
card
1. Insert the memory card into the card slot.
1. Insert the memory card into the card slot.
2. Press 7 SETTING.
2. Press 7 SETTING.
3. Use the bq up (q) and down (w) buttons to
3. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to
“CardUtility” and then press
ENTER.
move the item selection cursor (0) to
“CardUtility” and then press
ENTER.
• This causes the CARD UTIL screen to appear.
• This causes the CARD UTIL screen to appear.
bq
4. Use the bq up (q) and down (w) buttons to
move the item selection cursor (0) to “Delete”
and then press the
ENTER button.
bq
• This displays a screen for specifying the file to be
deleted.
bq
4. Use the bq cursor (U, q, w, I) buttons to
move the item selection cursor (0) to
“Rename” and then press the
ENTER
button.
bq
• This displays a screen for specifying the file to be
renamed.
5. Use the bo dial or bq minus (–) and plus (+)
buttons to display the file you want to rename.
6. Use the bq left (U) and right (I) buttons to
move the cursor to the name character position
you want to change, and then use the
dial or
minus (–) and plus (+) buttons to select the
character you want.
bo
bq
5. Use the bo dial or bq minus (–) and plus (+)
buttons to display the file you want to delete.
6. Press the bq ENTER button.
7. In response to the “Sure?” message that
bq
appears, press the
YES button to delete or
the
NO button to cancel.
bq
bq
• Pressing the
YES button displays the message
“Please Wait” (indicating the operation is in progress).
Do not perform any operation while this message is on
the display. “Complete!” appears on the display after
the operation is complete.
7. After the name is the way you want, press the
bq ENTER button.
8. In response to the “Sure?” message that
bq
appears, press the
YES button to rename
the file or the
NO button to cancel.
bq
bq
• Pressing the
YES button displays the message
“Please Wait” (indicating the operation is in progress).
Do not perform any operation while this message is on
the display. “Complete!” appears on the display after
the operation is complete.
Playing a Music File from a
Memory Card
You can use the Synthesizer to play music files and audio
files that you have saved to a card with your computer.
For details about the playback method, see “Playing a Demo
Tune or a File from a Memory Card” on page E-72.
E-78
Connecting to a Computer
You can connect the Synthesizer to a computer and
exchange MIDI data between them. You can send play data
from the Synthesizer to music software running on your
computer, or you can send MIDI data from your computer to
the Synthesizer for playback.
Minimum Computer System
Requirements
2. After starting up your computer, use a
commercially available USB cable to connect it
to the Synthesizer.
B connector
USB cable
(A-B type)
Synthesizer USB port
A connector
The following shows the minimum computer system
requirements for sending and receiving MIDI data. Check to
make sure that your computer complies with these
requirements before connecting the Synthesizer to it.
• Operating System
Windows® XP (SP2 or later) *1
Windows Vista® *2
Windows® 7*3
Mac OS® X (10.3.9, 10.4.11, 10.5.8 or later,
10.6.8 or later, 10.7.1 or later)
*1: Windows XP Home Edition
Windows XP Professional (32-bit)
*2: Windows Vista (32-bit)
*3: Windows 7 (32-bit, 64-bit)
• USB port
• Never connect to a computer that does not conform to
the above requirements. Doing so can cause problems
with your computer.
Connecting the Synthesizer to Your
Computer
• Make sure you follow the steps of the procedure below
exactly. Connecting incorrectly can make data send
and receive impossible.
1. Turn off the Synthesizer and then start up your
computer.
• Do not start up the music software on your computer
yet!
Computer USB port
3. Turn on the Synthesizer.
• If this is the first time you are connecting the
Synthesizer to your computer, the driver software
required to send and receive data will be installed on
your computer automatically.
4. Start up your computer’s music software.
5. Configure the music software settings to select
one of the following as the MIDI device.
CASIO USB-MIDI : (For Windows 7, Windows Vista,
Mac OS X)
USB Audio Device : (For Windows XP)
• For information about how to select the MIDI device,
see the user documentation that comes with the music
software you are using.
• Be sure to turn on the Synthesizer first before starting
up your computer’s music software.
• Once you are able to connect successfully for the first time,
there is no problem with leaving the USB cable connected
when you turn off your computer and/or Synthesizer.
• You can alter the Synthesizer’s MIDI setup by changing the
MIDI data send channel or other settings. For details, see
“MIDI Settings” (page E-70).
• For detailed specifications and connections that apply to
MIDI data send and receive by this Synthesizer, see the
latest support information provided by the website at the
following URL.
http://world.casio.com/
E-79
Connecting to a Computer
Saving and Loading Synthesizer
Data to a Computer and Editing
Synthesizer Data on a Computer
You can transfer user tones, phrases, and other data you
saved with the Synthesizer to a computer for storage. Later,
you can return the data back to the Synthesizer when you
need it.
You can also edit tone, performance and other Synthesizer
data on a computer, where it is easier to work with. A special
Data Editor application is required in order to perform
operations such as these.
1. Go to the CASIO WORLDWIDE site at the
following URL.
http://world.casio.com/
2. At the site, select a geographic area or country.
3. After accessing the area site, navigate to the
minimum computer system requirements for
Data Editor for this product.
• You should be able to find a link to Data Editor
information on the product introduction page of this
product. If you cannot find such a link, use the search
form of the area site where you are located to enter the
model name of this product and search for it.
• Note that site contents are subject to change without
notice.
4. Check if your computer system complies with
the minimum requirements for Data Editor.
5. Download Data Editor and its user’s guide to
your computer.
6. Follow the procedure in the Data Editor user’s
guide you downloaded in step 5 to install Data
Editor.
7. Use the procedures in the Data Editor user’s
guide to transfer and edit data.
• See the Data Editor user’s Guide for information about
the types of data that can be transferred and the data
that can be edited.
E-80
Reference
Error Messages
Display
Message
Cause
Required Action
1. The current memory card format is not compatible
with this Synthesizer.
1. Format the memory card on the Synthesizer (page
E-75).
2. The memory card capacity is greater than 32GB.
2. Use a memory card with a capacity of 32GB or
less.
3. You are trying to use an SDXC card.
3. SDXC cards not supported. Use an SD or SDHC
memory card.
4. There is something wrong with the memory card.
4. Use a different memory card.
Card Full
There is not enough room available on the memory
card.
Delete some of the files on the memory card to make
room for new data (page E-78), or use a different
card.
Card R/W
Memory card data is corrupted.
Use a different memory card.
No Card
1. The memory card is not loaded correctly in the
Synthesizer’s card slot.
1. Correctly load the memory card into the card slot.
2. The memory card was removed while some
operation was in progress.
2. Do not remove the memory card while any
operation is in progress.
No Data
You tried to save a Synthesizer user area (user
rhythm, user rhythm song, etc.) that does not contain
any data to the memory card.
Select a user area that contains data.
No File
1. There is no MUSICDAT folder (page E-77) on the
memory card.
1. Create a MUSICDAT folder on the memory card or
format the memory card on the Synthesizer (page
E-75).
2. There is no loadable or playable data in the
MUSICDAT folder.
2. Move the file you want to load or play into the
memory card’s MUSICDAT folder.
Not SMF0/1
You are attempting to play back SMF Format 2 file.
This Synthesizer supports playback of SMF Format 0
or Format 1 only.
Protect
The memory card is write-protected.
Use the memory card’s write protect switch to enable
writing.
Read Only
A read-only file with the same name you are trying to
use is already stored on the memory card.
• Use a different name to save the new file.
• Remove the read-only attribute from the existing
file and overwrite it with the new file.
• Use a different memory card.
Size Over
1. The data on the memory card is too big to play.
1. This Synthesizer supports playback of song data
files with a maximum size of about 320KB.
2. The data you are trying to load is too large.
2. The following is the approximate maximum data
sizes (per data item) when loading data into
Synthesizer memory.
User phrase: 8KB
A total of approximately 128KB of user phrase
(total of all 100 user presets) can be loaded.
3. Chain SMF data size is too large to convert the
data and save it to a card.
3. The Synthesizer can convert up to 320KB of chain
SMF data and save it to a card.
1. The memory card data is corrupted.
Use a different memory card.
Format
Wrong Data
2. The memory card contains data that is not
supported by this Synthesizer.
Memory Full
There is not enough memory capacity required for
phrase sequencer operations.
Shorten the phrase so it takes up less memory space.
E-81
Reference
Display
Message
Cause
Required Action
File Name
When renaming a file on a memory card, attempting
to specify a file name that is already used.
Use a different name.
Invalid Tone
You selected a Synthesizer tone, hexlayer tone, or
drawbar organ tone for a part other than PART1
(ZONE1).
Select Synthesizer, hexlayer, or drawbar organ tones
only for PART1 (ZONE1).
Battery Low
Battery power is low.
Replace the batteries or change to AC adaptor power
(page E-9).
Write Error!
Writing to internal storage memory failed.
Try again.
Troubleshooting
Symptom
Action
Included Accessories
I can’t find something that should be
included with the product.
Carefully check inside all of the packing materials.
Power Requirements
Power will not turn on.
• Check the AC adaptor or make sure that the batteries are facing correctly (page
E-9).
• Replace the batteries with new ones or switch over to AC adaptor power (page
E-9).
The display lights up momentarily but
power does not turn on when I press
POWER.
6
Press
6 POWER firmly and completely to turn on power.
The Synthesizer outputs a loud sound and Replace the batteries with new ones or switch over to AC adaptor power (page
then suddenly powers down.
E-9).
The Synthesizer suddenly powers down
after a few minutes.
This happens when Auto Power Off (page E-10) is triggered.
Display
The display keeps going out or is flashing. Replace the batteries with new ones or switch over to AC adaptor power (page
E-9).
Screen contents are visible only from
straight ahead.
This is due to production limitations. It does not indicate malfunction.
Sound
Nothing happens when I press any
keyboard key.
• Adjust the main volume setting (page E-12).
• This Synthesizer does not have built-in speakers. It will no produce unless you
connect some device for sound output (page E-8).
No sound is produced when a start the
Step Sequencer.
When the arpeggio function is being triggered by start of the Step Sequencer, the
sequence will not start until you play something on the keyboard.
Notes keep sounding, without stopping.
Replace the batteries with new ones or switch over to AC adaptor power (page
E-9).
Some notes are cut off while they are
playing.
Notes are cut off whenever the number of notes being sounded exceeds the
maximum polyphony value of 64 (1 to 32 for some tones). This does not indicate
malfunction.
The volume or tone setting I configured
has changed.
• Adjust the main volume setting (page E-12).
• Replace the batteries with new ones or switch over to AC adaptor power (page
E-9).
Output volume does not change even
though I change my keyboard pressure.
Change the Touch setting (page E-65).
E-82
Reference
Symptom
Action
In certain keyboard ranges, the volume
and tone quality sound are slightly
different from those in other keyboard
ranges.
This is due to system limitations. It does not indicate malfunction.
With some tones, octaves do not change
at the far ends of the keyboard.
This is due to system limitations. It does not indicate malfunction.
The pitch of the notes does not match
other accompanying instruments or
sounds strange when played along with
other instruments.
Check the transpose and octave shift settings (page E-36).
There is digital noise mixed with the sound This is due to system limitations. It does not indicate malfunction.
when I play high notes with a Solo
Synthesizer tone.
The reverb of notes seems to change
suddenly.
Check and adjust the reverb setting (page E-37).
Computer Connection
I can’t exchange data between the
Synthesizer and a computer.
• Check to make sure that the USB cable is connected to the Synthesizer and
computer, and that the device is selected correctly with your computer’s music
software settings (page E-79).
• Turn off the Synthesizer and then exit the music software on your computer.
Next, turn the Synthesizer back on and then restart the music software on your
computer.
E-83
Reference
Specifications
Model
Keyboard
Touch Response
XW-P1
61 standard-size keys
2 types, Off
Maximum Polyphony
64 notes (1 to 32 for some tones)
Tones
620 preset, 310 user
Solo Synthesizer Tones
100 preset, 100 user
Hex Layer Tones
50 preset, 50 user
Drawbar Organ Tones
50 preset, 50 user
PCM Melody Tones
400 preset, 100 user
PCM Drum Tones
20 preset, 10 user
Effects
Reverb
System reverb
Chorus
System chorus
DSP
100 preset, 100 user
53 types (46 normal, 7 Solo Synthesizer)
Master Equalizer
4 bands
Demo Songs
3 songs
Performance Functions
100 preset, 100 user
Phrase Functions
Preset Phrases
100
User Phrases
100
Playback Mode
One time, loop
Memory Capacity
128KB
Other
Overdubbing
Step Sequencer Functions
Preset Sequences
100
User Sequences
100
Number of Tracks
Mono: 8, Poly: 1, Control: 4
Patterns
8 types per sequence
Chains
100
Maximum Steps
16
Other
Mixer
Phrase function control
16 internal parts + Externally input parts
Other Functions
Transpose
±1 octaves (–12 to 0 to +12 semitones)
Octave Shift
±3 octaves
Tuning
A4 = 415.5 - 440.0 - 465.9Hz
Arpeggios
Preset: 100
User: 100
MIDI
16 multi-timbre received, GM Level 1 standard
Wheels
Bender, modulation
Memory Cards
Supported Memory Cards
SD or SDHC memory cards, 32GB or less
Functions
SMF playback, audio file playback, file storage, file recall, file delete, card format
E-84
Reference
Inputs/Outputs
USB port
TYPE B
MIDI IN/OUT terminal
IN, OUT
Sustain/Assignable jack
Standard jack (sustain, sostenuto, soft, start/stop)
Phones jack
Stereo standard jack
Line Out R, L/MONO jacks
Standard jack × 2
Output Impedance: 2.3kΩ, Output Voltage: 1.7V (RMS) MAX
Audio In jack
Stereo mini jack
Input Impedance: 9kΩ, Input Sensitivity: 200mV
Inst In Jack
Standard jack
Input Impedance: 9kΩ, Input Sensitivity: 200mV
Mic In jack
Standard jack (connect a dynamic microphone only)
Input Impedance: 3kΩ, Input Sensitivity: 10mV
Power Jack
9.5V DC
Power Supply
2-way
Batteries
6 D-size zinc-carbon batteries or alkaline batteries
Battery Life
Approximately 35 hours (alkaline batteries, using the optional CASIO CP-16 headphones)
AC Adaptor
AD-E95100L
Auto Power Off
Approximately 6 minutes after last key operation during battery use,
approximately 4 hours after last key operation during AC adaptor use. Auto Power Off can be
disabled.
Power Consumption
9.5V = 4W
Dimensions
94.8 × 38.4 × 12.4 cm (37 3/8 × 15 1/8 × 4 7/8 inch)
Weight
Approximately 5.4kg (11.9 lbs) (without batteries)
• Design and specifications are subject to change without notice.
E-85
Reference
Operating Precautions
Be sure to read and observe the following operating
precautions.
■ Location
Avoid the following locations for this product.
• Areas exposed to direct sunlight and high humidity
• Areas subjected to temperature extremes
• Near a radio, TV, video deck, or tuner
The above devices will not cause malfunction of the
product, but the product can cause interference in the audio
or video of a nearby device.
■ User Maintenance
• Never use benzine, alcohol, thinner, or other chemical
agents to clean the product.
• To clean the product or its keyboard, wipe with a soft cloth
moistened in a weak solution of water and a mild neutral
detergent. Wring all excess moisture from the cloth before
wiping.
■ Included and Optional Accessories
Use only accessories that are specified for use with this
product. Use of unauthorized accessories creates the risk of
fire, electric shock, and personal injury.
■ AC Adaptor Handling Precautions
• Use a power outlet that is easily accessible so you can
unplug the AC adaptor when a malfunction occurs or
whenever else you need to do so.
• The AC adaptor is intended for indoor use only. Do not use
it where it might be exposed to splashing or moisture. Do
not place any container, such as a flower vase, that
contains liquid on the AC adaptor.
• Store the AC adaptor in a dry place.
• Use the AC adaptor in an open, well-ventilated area.
• Never cover the AC adaptor with newspaper, a table cloth,
a curtain, or any other similar item.
• Unplug the AC adaptor from the power outlet if you do not
plan to use the product for a long time.
• Never try to repair the AC adaptor or modify it in any way.
• AC adaptor operating environment
Temperature: 0 to 40°C
Humidity: 10% to 90% RH
• Output polarity: &
■ Weld Lines
Lines may be visible on the exterior of the product. These are
“weld lines” that result from the plastic molding process. They
are not cracks or scratches.
■ Musical Instrument Etiquette
Always be aware of others around you whenever using this
product. Be especially careful when playing late at night to
keep the volume at levels that do not disturb others. Other
steps you can take when playing late at night are closing
windows and using headphones.
E-86
Reference
DSP Effect List
DSP Type List
■ Normal DSP Types
• Type numbers 01 through 14 are single type DSPs, while numbers 15 through 46 are dual type DSPs. A single type DSP is one
with a single structure, while a dual type is a combination of two single type DSPs.
• The name of a dual DSP is formed by its two constituent single DSP names, in the order that they are applied. For example, type
15 named “Wah-Compressor” connects in line to “Wah” and “Compressor”, in that sequence.
Type Number
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
DSP Type Name
Wah
Compressor
Distortion
Enhancer
AutoPan
Tremolo
Phaser
Flanger
Chorus
Delay
Reflection
Rotary
RingModulator
Lo-Fi
Wah-Compressor
Wah-Distortion
Wah-Chorus
Wah-Flanger
Wah-Reflection
Wah-Tremolo
Wah-AutoPan
Compressor-Wah
Compressor-Distortion
Screen Name
Wah
Comp
Dist
Enhance
AutoPan
Tremolo
Phaser
Flanger
Chorus
Delay
Reflect
Rotary
RingMod
Lo-Fi
WahCmp
WahDst
WahCho
WahFln
WahRef
WahTrm
WahPan
CmpWah
CmpDst
Type Number
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
DSP Type Name
Compressor-Chorus
Compressor-Flanger
Compressor-Reflection
Compressor-Tremolo
Compressor-AutoPan
Distortion-Wah
Distortion-Compressor
Distortion-Chorus
Distortion-Flanger
Distortion-Reflection
Distortion-Tremolo
Distortion-AutoPan
Chorus-Reflection
Chorus-AutoPan
Flanger-Reflection
Flanger-AutoPan
Reflection-Distortion
Reflection-Chorus
Reflection-AutoPan
Tremolo-Distortion
Tremolo-Chorus
Tremolo-Flanger
Tremolo-Reflection
Screen Name
CmpCho
CmpFln
CmpRef
CmpTrm
CmpPan
DstWah
DstCmp
DstCho
DstFln
DstRef
DstTrm
DstPan
ChoRef
ChoPan
FlnRef
FlnPan
RefDst
RefCho
RefPan
TrmDst
TrmCho
TrmFln
TrmRef
• For details about parameters that can be configured with each DSP type, refer to the sections shown in the table below.
For information about this DSP type:
Go here:
Single type (Type numbers 01 through 14)
Normal DSP Single Type DSP Parameters (page E-88)
Dual type (Type numbers 15 through 46)
Normal DSP Dual Type DSP Parameters (page E-90)
■ Solo Synthesizer DSP Types
Type Number
01
02
03
DSP Type Name
Bypass
Auto Pan
Distortion
Flanger
Screen Name
Bypass
AutoPan
Dist
Flanger
Type Number
DSP Type Name
04
Chorus
05
Delay
06
Ring Modulator
Screen Name
Chorus
Delay
RingMod
• For information about the parameters whose settings can be configured for each DSP type, see “Solo Synthesizer DSP
Parameters” (page E-90).
E-87
Reference
DSP Parameter List
■ Normal DSP Single Type DSP Parameters
• (Param A) and (Param B) are parameters assigned to the
8/16 and MASTER sliders when Hex Layer tones are
selected.
5
01: Wah
This is a “wah” effect that can automatically affect the
frequency using an LFO.
Parameters and Value Ranges:
1 :Resonance (0 to 127) (Param B)
Adjusts the strength of resonance.
2 :Manual (0 to 127) (Param A)
Adjusts the wah filter reference frequency.
3 :LFO Rate (0 to 127)
Adjusts the LFO rate.
4 :LFO Depth (0 to 127)
Adjusts the LFO depth.
5 :LFO Waveform (off, sin, tri, random)
Selects the LFO waveform.
02: Compressor
Compresses the input signal, which can have the effect of
suppressing level variation and make it possible to sustain
dampened sounds longer.
Parameters and Value Ranges:
1 :Attack (0 to 127)
Adjusts the attack amount of the input signal. A smaller
value causes prompt compressor operation, which
suppresses the attack of the input signal. A larger values
delays compressor operation, which causes the attack of
the input signal to be output as-is.
2 :Release (0 to 127)
Adjusts the time from the point the input signal drops
below a certain level until the compression operation is
stopped. When an attack feeling is desired (no
compression at the onset of sound), set this parameter to
as low a value as possible. To have compression applied
at all times, set a high value.
3 :Level (0 to 127) (Param B)
Adjusts the output level.
4 :Threshold (0 to 127) (Param A)
Adjusts the volume level at which the compression
operation starts.
03: Distortion
Digital distortion that applies an overtone to the input signal
and distorts it.
Parameters and Value Ranges:
1 :Gain (0 to 127) (Param A)
Adjusts the input signal gain.
2 :Level (0 to 127) (Param B)
Adjusts the output level.
E-88
04: Enhancer
Phase shifts low-range sounds and high-range sounds of the
input signal to enhance the signal’s profile.
Parameters and Value Ranges:
1 :Low Frequency (0 to 127) (Param A)
Adjusts the low range enhancer frequency.
2 :Low Phase (0 to 127)
Adjusts the phase shift amount of the low-range enhancer.
3 :High Frequency (0 to 127) (Param B)
Adjusts the high range enhancer frequency.
4 :High Phase (0 to 127)
Adjusts the phase shift amount of the high-range
enhancer.
05: Auto Pan
Performs continual left-right panning of the input signal using
an LFO.
Parameters and Value Ranges:
1 :LFO Rate (0 to 127)
Adjusts the panning rate.
2 :LFO Depth (0 to 127) (Param B)
Adjusts the panning depth.
3 :LFO Waveform (sin, tri)
Selects the LFO waveform.
4 :Manual (Range: –64 to 0 to 63) (Param A)
Adjusts the pan (stereo position).
–64 is full left, 0 is center, and 63 is full right.
06: Tremolo
Adjusts the volume of the input signal using an LFO.
Parameters and Value Ranges:
1 :LFO Rate (0 to 127) (Param A)
Adjusts the tremolo rate.
2 :LFO Depth (0 to 127) (Param B)
Adjusts the tremolo depth.
3 :LFO Waveform (sin, tri)
Selects the LFO waveform.
07: Phaser
Produces a distinctive pulsating, broad sound by using an
LFO to change the phase of the input signal and then mixes it
with the original input signal.
Parameters and Value Ranges:
1 :Resonance (0 to 127)
Adjusts the strength of the resonance.
2 :LFO Rate (0 to 127) (Param A)
Adjusts the LFO rate.
3 :LFO Depth (0 to 127) (Param B)
Adjusts the LFO depth.
4 :LFO Waveform (sin, tri, random)
Selects the LFO waveform.
Reference
08: Flanger
11: Reflection
Applies wildly pulsating and metallic reverberation to sounds.
LFO waveform is selectable.
Parameters and Value Ranges:
1 :LFO Rate (0 to 127) (Param A)
Adjusts the LFO rate.
2 :LFO Depth (0 to 127) (Param B)
Adjusts the LFO depth.
3 :LFO Waveform (sin, tri, random)
Selects the LFO waveform.
4 :Feedback (0 to 127)
Adjusts the strength of feedback.
An effector that extracts early reflections from reverb. Applies
acoustic presence to sounds.
Parameters and Value Ranges:
1 :Type (1, 2, 3, 4, 5, 6, 7, 8) (Param A)
Selects from among the eight available reflection patterns.
2 :Feedback (0 to 127) (Param B)
Adjusts the repeat of the reflected sound.
09: Chorus
Gives sounds depth and breadth. Chorus type is selectable.
Parameters and Value Ranges:
1 :LFO Rate (0 to 127) (Param A)
Adjusts the LFO rate.
2 :LFO Depth (0 to 127) (Param B)
Adjusts the LFO depth.
3 :LFO Waveform (sin, tri)
Selects the LFO waveform.
4 :Feedback (0 to 127)
Adjusts the strength of feedback
5 :Type (mono, stereo, tri)
Selects the chorus type.
10: Delay
Delays the input signal and feeds it back to create a repeating
effect and give sounds more breadth.
Parameters and Value Ranges:
1 :Delay Time (0 to 127) (Param A)
Adjusts the delay time.
2 :Feedback (0 to 127)
Adjusts the repeat of the delay.
3 :Ratio Lch (0 to 127)
Adjusts the delay time of the left channel. This value is a
ratio of the value specified for Delay Time.
4 :Ratio Rch (0 to 127)
Adjusts the delay time of the right channel. This value is a
ratio of the value specified for Delay Time.
5 :Wet Level (0, 1, 2, 3, 4, 5) (Param B)
Adjusts the level of the delay sound.
6 :Type (1, 2)
Selects the delay type.
1 :Delay repeat determined by Delay Time.
2 :Delay repeat determined by Delay Time and Ratio L/R.
7 :Tempo Sync (Range: Off, 1/4, 1/3, 3/8, 1/2, 2/3, 3/4, 1,
4/3, 3/2, 2)
Adjusts the relationship between tempo and delay time of
the Sequencer.
When Off is selected, the current setting of the Delay Time
parameter is used for the delay time. When any other
setting is selected, the delay time is synced with the
Sequencer beat.
Selecting 1, for example, the delay time is approximately
equal to the length of one beat.
(Delay time is not precisely synced with the beat.)
12: Rotary
This is a rotary speaker simulator.
Parameters and Value Ranges:
1 :Overdrive Gain (0, 1, 2, 3) (Param A)
Adjusts overdrive gain.
2 :Overdrive Level (0 to 127)
Adjusts the overdrive output level.
3 :Speed (Slow, Fast) (Param B)
Switches the speed mode between fast and slow.
4 :Brake (Rotate, Stop)
Stops speaker rotation.
5 :Fall Acceleration (0 to 127)
Adjusts acceleration when the speed mode is switched
from fast to slow.
6 :Rise Acceleration (0 to 127)
Adjusts acceleration when the speed mode is switched
from slow to fast.
7 :Slow Rate (0 to 127)
Adjusts the speaker rotation speed in the slow speed
mode.
8 :Fast Rate (0 to 127)
Adjusts the speaker rotation speed in the fast speed
mode.
13: Ring Modulator
Multiplies the input signal with an internal oscillator signal to
create a metallic sound.
Parameters and Value Ranges:
1 :OSC Frequency (0 to 127) (Param A)
Sets the reference frequency of the internal oscillator.
2 :LFO Rate (0 to 127)
Adjusts the LFO rate.
3 :LFO Depth (0 to 127) (Param B)
Adjusts the LFO depth.
4 :Type (1, 2, 3)
1 :Outputs the ring modulated signal only.
2 :Outputs the ring modulated signal and the input signal.
3 :Outputs a signal with a chorus effect applied to 2 (ring
modulated signal and input signal).
Important!
When adjusting the delay time and type, certain settings can
result in a switching sound in the delay.
E-89
Reference
14: Lo-Fi
Applies various types of noise to the input signal to reproduce
a retro Lo-Fi sound.
Includes wow and flutter for rotational fluctuation like that in
tapes and records, a Noise 1 generator that generates
continual FM radio type, and a Noise 2 generator that
generates record play types scratch noise.
Parameters and Value Ranges:
1 :Wow and Flutter Rate (0 to 127)
Adjusts the wow and flutter rate.
2 :Wow and Flutter Depth (0 to 127)
Adjusts the wow and flutter depth.
3 :Noise1 Level (0, 1, 2, 3, 4, 5) (Param A)
Adjusts the level of Noise Generator 1.
4 :Noise2 Level (0, 1, 2, 3, 4, 5) (Param B)
Adjusts the level of Noise Generator 2.
5 :Noise2 Density (0, 1, 2, 3, 4, 5)
Adjusts the frequency of Noise Generator 2.
6 :Bit (0, 1, 2, 3)
Distorts the sound. A larger number produces greater
distortion.
Important!
Raising the noise level while a note is not sounding will cause
noise to sound, even if there is no input signal.
■ Normal DSP Dual Type DSP Parameters
Dual type DSPs are configured by combining two different
single type DSPs. Use the procedure below to determine what
parameters that can be configured for each dual type DSP,
and the operation, and setting ranges of dual type DSPs.
Example: Type number 29: Distortion-Wah
1. The DSP type name has two parts: a left side part and a
right side part.
Distortion-Wah 3 “Distortion” and “Wah”
2. Find out what parameters you can configure by looking up
the left side part of a dual type DSP in the “Type Name”
column of the table below.
Type Name
Wah
Configurable Parameters
LFO Waveform
LFO Rate
LFO Depth (Param)
Distortion
Gain (Param)
Level
Chorus
LFO Waveform
LFO Rate (Param)
LFO Depth
Flanger
LFO Waveform
LFO Rate (Param)
LFO Depth
3. Find the same type names in the table under “Normal DSP
Single Type DSP Parameters” on pages E-88 through
E-90, and note the operation and setting ranges of the
items that are the same as those shown in the
“Configurable Parameters” column of the above table.
• In our “Distortion-Wah” example, the left side part of the
name is “Distortion” so we can see in the above table
that “Gain” and “Level” parameters can be configured.
You can find out about the operations and setting ranges
of “Gain” and “Level” by referring to “03: Distortion” on
page E-88.
4. Next, repeat steps 2 and 3 above for the right side part of
the dual type DSP parameter name.
• The parameter numbers that appear on the parameter
setting screen start from 1, and the number is
incremented for each successive parameter.
The parameter numbers of our “Distortion-Wah” example
would be as shown below.
1: Gain
2: Level
3: LFO Waveform
4: LFO Rate
5: LFO Depth
• (Param) in the table under step 2 of this procedure are
parameters assigned to the
8/16 and MASTER sliders
when Hex Layer tones are selected. The (Param) of the
single type DSP whose name is on the left is assigned the
8/16 button, while the single type DSP whose name is
on the right is assigned the
MASTER button.
5
5
5
■ Solo Synthesizer DSP Parameters
• (Param A) and (Param B) are parameters assigned to the
8/16 and MASTER sliders when Solo Synthesizer
tones are selected.
5
(No number): Bypass
Selecting this option disables application of DSP.
No parameters
01: Auto Pan
Parameters and Ranges
1 :LFO Waveform (Range: sin, tri)
2 :LFO Rate (Range: 0 to 127) (Param A)
3 :LFO Depth (Range: 0 to 127) (Param B)
4 :Manual (Range: –64 to 0 to 63)
02: Distortion
Reflection
Feedback (Param)
Parameters and Ranges:
1 :Gain (Range: 0 to 127) (Param A)
2 :Level (Range: 0 to 127) (Param B)
Compressor
Threshold (Param)
Level
03: Flanger
Auto Pan
LFO Waveform
LFO Rate
LFO Depth
Manual (Param)
Parameters and Ranges
1 :LFO Waveform (Range: sin, tri, random)
2 :LFO Rate (Range: 0 to 127) (Param A)
3 :LFO Depth (Range: 0 to 127) (Param B)
Tremolo
LFO Waveform
LFO Rate (Param)
LFO Depth
E-90
Reference
04: Chorus
Parameters and Ranges
1 :LFO Waveform (Range: sin, tri)
2 :LFO Rate (Range: 0 to 127) (Param A)
3 :LFO Depth (Range: 0 to 127) (Param B)
Supported Input Characters
05: Delay
Parameters and Ranges
1 :Delay Time (Range: 0 to 127) (Param A)
2 :Feedback (Range: 0 to 127)
3 :Damp (Range: 0 to 3)
Adjusts damping of the high-range. 3 results in maximum
damping.
4 :Wet Level (Range: 0, 1, 2, 3, 4, 5) (Param B)
5 :Tempo Sync (Range: Off, 1/4, 1/3, 3/8, 1/2, 2/3, 3/4, 1,
4/3, 3/2, 2)
06: Ring Modulator
Parameters and Ranges
1 :Frequency (Range: 0 to 127) (Param A)
Adjusts the modulation frequency of the ring modulator.
2 :Dry Level (Range: 0 to 127)
Adjusts the level of the original sound.
3 :Wet Level (Range: 0 to 127) (Param B)
Adjusts the sound level of the ring modulator.
• For information about parameters not included in the
above, see the explanations of the parameters with the
same names under “Normal DSP Single Type DSP
Parameters” (page E-88).
E-91
Control
Change
0
1
5
6, 38
7
10
11
16 - 19
64
65
Key’s
Ch’s
After
Touch
Pitch Bender
Note ON
Note OFF
Velocity
True voice
O
O
O *2
O *2
O
O
X
O *2
O *3
O *2
O
X
X
O 9nH v = 1 - 127
X 9nH v = 0
0 - 127
Mode 3
X
Default
Messages
Altered
Mode
Note
Number
1 - 16
1 - 16
Default
Changed
Transmitted
O
O
O *2
O *2
O
O
O
O *2
O
O *2
O
X
O
O 9nH v = 1 - 127
X 9nH v = 0, 8nH v =**
0 - 127
0 - 127 *1
Mode 3
X
1 - 16
1 - 16
Recognized
MIDI Implementation Chart
Basic
Channel
Function
Model: XW-P1
Hold 1
Portamento On/Off
Bank select
Modulation
Portamento Time
Data entry LSB, MSB
Volume
Pan
Expression
**: no relation
Remarks
Version : 1.0
:True #
Mode 1 : OMNI ON, POLY
Mode 3 : OMNI OFF, POLY
Remarks
Messages
O
O
O
O
O
X
X
X
X
X
X
O *2
O
0 - 127
O
O
O *2
O
O
O *2
O *2
Reverb send
Chorus send
NRPN LSB, MSB
RPN LSB, MSB
Sostenuto
Soft pedal
Mode 2 : OMNI ON, MONO
Mode 4 : OMNI OFF, MONO
O : Yes
X : No
*1: Depends on tone.
*2: For details about NRPN, RPN, and system exclusive messages, see MIDI Implementation at
http://world.casio.com/.
*3: In accordance with pedal effect setting.
X
O
X
O
X
X
: All sound off
: Reset all controller
: Local ON/OFF
: All notes OFF
: Active Sense
: Reset
Aux
O
O
: Clock
: Commands
System
Real Time
X
X
X
: Song Pos
: Song Sel
: Tune
O *2
O
O *3
O *3
O *2
O
O
O *2
O *2
System
Common
System Exclusive
Program
Change
66
67
70 - 90
91
93
98, 99
100, 101
This recycle mark indicates that the packaging conforms to
the environmental protection legislation in Germany.
K
MA1203-B Printed in China
XWP1-E-1B